diff options
Diffstat (limited to 'board/toradex/colibri_imx6')
| -rw-r--r-- | board/toradex/colibri_imx6/800mhz_2x64mx16.cfg | 58 | ||||
| -rw-r--r-- | board/toradex/colibri_imx6/800mhz_4x64mx16.cfg | 58 | ||||
| -rw-r--r-- | board/toradex/colibri_imx6/MAINTAINERS | 3 | ||||
| -rw-r--r-- | board/toradex/colibri_imx6/clocks.cfg | 41 | ||||
| -rw-r--r-- | board/toradex/colibri_imx6/colibri_imx6.c | 395 | ||||
| -rw-r--r-- | board/toradex/colibri_imx6/colibri_imx6.cfg | 37 | ||||
| -rw-r--r-- | board/toradex/colibri_imx6/ddr-setup.cfg | 97 | ||||
| -rw-r--r-- | board/toradex/colibri_imx6/do_fuse.c | 2 | ||||
| -rw-r--r-- | board/toradex/colibri_imx6/pf0100.c | 177 | ||||
| -rw-r--r-- | board/toradex/colibri_imx6/pf0100.h | 59 | ||||
| -rw-r--r-- | board/toradex/colibri_imx6/pf0100_otp.inc | 16 |
11 files changed, 388 insertions, 555 deletions
diff --git a/board/toradex/colibri_imx6/800mhz_2x64mx16.cfg b/board/toradex/colibri_imx6/800mhz_2x64mx16.cfg deleted file mode 100644 index c9407143d2..0000000000 --- a/board/toradex/colibri_imx6/800mhz_2x64mx16.cfg +++ /dev/null @@ -1,58 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2013 Boundary Devices - * Copyright (C) 2014-2016, Toradex AG - */ - -DATA 4, MX6_MMDC_P0_MDPDC, 0x0002002D -DATA 4, MX6_MMDC_P0_MDCFG0, 0x2C305503 -DATA 4, MX6_MMDC_P0_MDCFG1, 0xB66D8D63 -DATA 4, MX6_MMDC_P0_MDCFG2, 0x01FF00DB -DATA 4, MX6_MMDC_P0_MDRWD, 0x000026D2 -DATA 4, MX6_MMDC_P0_MDOR, 0x00301023 -DATA 4, MX6_MMDC_P0_MDOTC, 0x00333030 -DATA 4, MX6_MMDC_P0_MDPDC, 0x0002556D -/* CS0 End: 7MSB of ((0x10000000 + 512M) -1) >> 25 */ -DATA 4, MX6_MMDC_P0_MDASP, 0x00000017 -/* DDR3 DATA BUS SIZE: 64BIT */ -/* DATA 4, MX6_MMDC_P0_MDCTL, 0x821A0000 */ -/* DDR3 DATA BUS SIZE: 32BIT */ -DATA 4, MX6_MMDC_P0_MDCTL, 0x82190000 - -/* Write commands to DDR */ -/* Load Mode Registers */ -/* TODO Use Auto Self-Refresh mode (Extended Temperature)*/ -/* DATA 4, MX6_MMDC_P0_MDSCR, 0x04408032 */ -DATA 4, MX6_MMDC_P0_MDSCR, 0x04008032 -DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033 -DATA 4, MX6_MMDC_P0_MDSCR, 0x00048031 -DATA 4, MX6_MMDC_P0_MDSCR, 0x13208030 -/* ZQ calibration */ -DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040 - -DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xA1390003 -DATA 4, MX6_MMDC_P1_MPZQHWCTRL, 0xA1390003 -DATA 4, MX6_MMDC_P0_MDREF, 0x00005800 - -DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00000000 -DATA 4, MX6_MMDC_P1_MPODTCTRL, 0x00000000 - -DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x42360232 -DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x021F022A -DATA 4, MX6_MMDC_P1_MPDGCTRL0, 0x421E0224 -DATA 4, MX6_MMDC_P1_MPDGCTRL1, 0x02110218 - -DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x41434344 -DATA 4, MX6_MMDC_P1_MPRDDLCTL, 0x4345423E -DATA 4, MX6_MMDC_P0_MPWRDLCTL, 0x39383339 -DATA 4, MX6_MMDC_P1_MPWRDLCTL, 0x3E363930 - -DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x00340039 -DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x002C002D -DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x00120019 -DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x0012002D - -DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800 -DATA 4, MX6_MMDC_P1_MPMUR0, 0x00000800 -DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000 -DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006 diff --git a/board/toradex/colibri_imx6/800mhz_4x64mx16.cfg b/board/toradex/colibri_imx6/800mhz_4x64mx16.cfg deleted file mode 100644 index c319d2a729..0000000000 --- a/board/toradex/colibri_imx6/800mhz_4x64mx16.cfg +++ /dev/null @@ -1,58 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2013 Boundary Devices - * Copyright (C) 2014-2016, Toradex AG - */ - -DATA 4, MX6_MMDC_P0_MDPDC, 0x0002002D -DATA 4, MX6_MMDC_P0_MDCFG0, 0x2C305503 -DATA 4, MX6_MMDC_P0_MDCFG1, 0xB66D8D63 -DATA 4, MX6_MMDC_P0_MDCFG2, 0x01FF00DB -DATA 4, MX6_MMDC_P0_MDRWD, 0x000026D2 -DATA 4, MX6_MMDC_P0_MDOR, 0x00301023 -DATA 4, MX6_MMDC_P0_MDOTC, 0x00333030 -DATA 4, MX6_MMDC_P0_MDPDC, 0x0002556D -/* CS0 End: 7MSB of ((0x10000000 + 512M) -1) >> 25 */ -DATA 4, MX6_MMDC_P0_MDASP, 0x00000017 -/* DDR3 DATA BUS SIZE: 64BIT */ -DATA 4, MX6_MMDC_P0_MDCTL, 0x821A0000 -/* DDR3 DATA BUS SIZE: 32BIT */ -/* DATA 4, MX6_MMDC_P0_MDCTL, 0x82190000 */ - -/* Write commands to DDR */ -/* Load Mode Registers */ -/* TODO Use Auto Self-Refresh mode (Extended Temperature)*/ -/* DATA 4, MX6_MMDC_P0_MDSCR, 0x04408032 */ -DATA 4, MX6_MMDC_P0_MDSCR, 0x04008032 -DATA 4, MX6_MMDC_P0_MDSCR, 0x00008033 -DATA 4, MX6_MMDC_P0_MDSCR, 0x00048031 -DATA 4, MX6_MMDC_P0_MDSCR, 0x13208030 -/* ZQ calibration */ -DATA 4, MX6_MMDC_P0_MDSCR, 0x04008040 - -DATA 4, MX6_MMDC_P0_MPZQHWCTRL, 0xA1390003 -DATA 4, MX6_MMDC_P1_MPZQHWCTRL, 0xA1390003 -DATA 4, MX6_MMDC_P0_MDREF, 0x00005800 - -DATA 4, MX6_MMDC_P0_MPODTCTRL, 0x00000000 -DATA 4, MX6_MMDC_P1_MPODTCTRL, 0x00000000 - -DATA 4, MX6_MMDC_P0_MPDGCTRL0, 0x42360232 -DATA 4, MX6_MMDC_P0_MPDGCTRL1, 0x021F022A -DATA 4, MX6_MMDC_P1_MPDGCTRL0, 0x421E0224 -DATA 4, MX6_MMDC_P1_MPDGCTRL1, 0x02110218 - -DATA 4, MX6_MMDC_P0_MPRDDLCTL, 0x41434344 -DATA 4, MX6_MMDC_P1_MPRDDLCTL, 0x4345423E -DATA 4, MX6_MMDC_P0_MPWRDLCTL, 0x39383339 -DATA 4, MX6_MMDC_P1_MPWRDLCTL, 0x3E363930 - -DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x00340039 -DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x002C002D -DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x00120019 -DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x0012002D - -DATA 4, MX6_MMDC_P0_MPMUR0, 0x00000800 -DATA 4, MX6_MMDC_P1_MPMUR0, 0x00000800 -DATA 4, MX6_MMDC_P0_MDSCR, 0x00000000 -DATA 4, MX6_MMDC_P0_MAPSR, 0x00011006 diff --git a/board/toradex/colibri_imx6/MAINTAINERS b/board/toradex/colibri_imx6/MAINTAINERS index 1cc7ef2e71..e25c07306c 100644 --- a/board/toradex/colibri_imx6/MAINTAINERS +++ b/board/toradex/colibri_imx6/MAINTAINERS @@ -1,8 +1,9 @@ Colibri iMX6 M: Max Krummenacher <max.krummenacher@toradex.com> W: http://developer.toradex.com/software/linux/linux-software +W: https://www.toradex.com/community S: Maintained F: board/toradex/colibri_imx6/ F: include/configs/colibri_imx6.h F: configs/colibri_imx6_defconfig -F: configs/colibri_imx6_nospl_defconfig +F: arch/arm/dts/imx6-colibri.dts diff --git a/board/toradex/colibri_imx6/clocks.cfg b/board/toradex/colibri_imx6/clocks.cfg deleted file mode 100644 index 1bcbc4fa38..0000000000 --- a/board/toradex/colibri_imx6/clocks.cfg +++ /dev/null @@ -1,41 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2013 Boundary Devices - * Copyright (C) 2014-2016, Toradex AG - * - * Device Configuration Data (DCD) - * - * Each entry must have the format: - * Addr-type Address Value - * - * where: - * Addr-type register length (1,2 or 4 bytes) - * Address absolute address of the register - * value value to be stored in the register - */ - -/* set the default clock gate to save power */ -DATA 4, CCM_CCGR0, 0x00C03F3F -DATA 4, CCM_CCGR1, 0x0030FC03 -DATA 4, CCM_CCGR2, 0x0FFFC000 -DATA 4, CCM_CCGR3, 0x3FF00000 -DATA 4, CCM_CCGR4, 0x00FFF300 -DATA 4, CCM_CCGR5, 0x0F0000C3 -DATA 4, CCM_CCGR6, 0x000003FF - -/* enable AXI cache for VDOA/VPU/IPU */ -DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF -/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */ -DATA 4, MX6_IOMUXC_GPR6, 0x007F007F -DATA 4, MX6_IOMUXC_GPR7, 0x007F007F - -/* - * Setup CCM_CCOSR register as follows: - * - * cko1_en = 1 --> CKO1 enabled - * cko1_div = 111 --> divide by 8 - * cko1_sel = 1011 --> ahb_clk_root - * - * This sets CKO1 at ahb_clk_root/8 = 132/8 = 16.5 MHz - */ -DATA 4, CCM_CCOSR, 0x000000fb diff --git a/board/toradex/colibri_imx6/colibri_imx6.c b/board/toradex/colibri_imx6/colibri_imx6.c index 17876f27e9..c634e3243d 100644 --- a/board/toradex/colibri_imx6/colibri_imx6.c +++ b/board/toradex/colibri_imx6/colibri_imx6.c @@ -2,40 +2,35 @@ /* * Copyright (C) 2010-2013 Freescale Semiconductor, Inc. * Copyright (C) 2013, Boundary Devices <info@boundarydevices.com> - * Copyright (C) 2014-2016, Toradex AG + * Copyright (C) 2014-2019, Toradex AG * copied from nitrogen6x */ #include <common.h> #include <dm.h> + #include <asm/arch/clock.h> #include <asm/arch/crm_regs.h> #include <asm/arch/imx-regs.h> -#include <asm/arch/iomux.h> -#include <asm/arch/mx6-pins.h> #include <asm/arch/mx6-ddr.h> +#include <asm/arch/mx6-pins.h> #include <asm/arch/mxc_hdmi.h> #include <asm/arch/sys_proto.h> #include <asm/bootm.h> #include <asm/gpio.h> +#include <asm/mach-imx/boot_mode.h> #include <asm/mach-imx/iomux-v3.h> -#include <asm/mach-imx/mxc_i2c.h> #include <asm/mach-imx/sata.h> -#include <asm/mach-imx/boot_mode.h> #include <asm/mach-imx/video.h> -#include <asm/io.h> +#include <cpu.h> #include <dm/platform_data/serial_mxc.h> -#include <dm/platdata.h> +#include <environment.h> #include <fsl_esdhc.h> -#include <i2c.h> -#include <input.h> #include <imx_thermal.h> -#include <linux/errno.h> -#include <malloc.h> #include <micrel.h> #include <miiphy.h> -#include <mmc.h> #include <netdev.h> +#include <cpu.h> #include "../common/tdx-cfg-block.h" #ifdef CONFIG_TDX_CMD_IMX_MFGR @@ -49,22 +44,16 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_SRE_FAST | PAD_CTL_HYS) #define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ + PAD_CTL_SPEED_LOW | PAD_CTL_DSE_40ohm | \ + PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_EMMC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ PAD_CTL_SRE_FAST | PAD_CTL_HYS) #define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) -#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ - PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) - -#define BUTTON_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) - -#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ - PAD_CTL_ODE | PAD_CTL_SRE_FAST) - #define WEAK_PULLUP (PAD_CTL_PUS_100K_UP | \ PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ PAD_CTL_SRE_SLOW) @@ -77,8 +66,6 @@ DECLARE_GLOBAL_DATA_PTR; PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ PAD_CTL_HYS | PAD_CTL_SRE_SLOW) -#define OUTPUT_40OHM (PAD_CTL_SPEED_MED|PAD_CTL_DSE_40ohm) - #define OUTPUT_RGB (PAD_CTL_SPEED_MED|PAD_CTL_DSE_60ohm|PAD_CTL_SRE_FAST) int dram_init(void) @@ -96,36 +83,8 @@ iomux_v3_cfg_t const uart1_pads[] = { MX6_PAD_CSI0_DAT11__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), }; -#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) -/* Colibri I2C */ -struct i2c_pads_info i2c_pad_info1 = { - .scl = { - .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC, - .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC, - .gp = IMX_GPIO_NR(1, 3) - }, - .sda = { - .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC, - .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC, - .gp = IMX_GPIO_NR(1, 6) - } -}; - -/* Colibri local, PMIC, SGTL5000, STMPE811 */ -struct i2c_pads_info i2c_pad_info_loc = { - .scl = { - .i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC, - .gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC, - .gp = IMX_GPIO_NR(2, 30) - }, - .sda = { - .i2c_mode = MX6_PAD_EIM_D16__I2C2_SDA | PC, - .gpio_mode = MX6_PAD_EIM_D16__GPIO3_IO16 | PC, - .gp = IMX_GPIO_NR(3, 16) - } -}; - -/* Apalis MMC */ +#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) +/* Colibri MMC */ iomux_v3_cfg_t const usdhc1_pads[] = { MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), @@ -139,18 +98,19 @@ iomux_v3_cfg_t const usdhc1_pads[] = { /* eMMC */ iomux_v3_cfg_t const usdhc3_pads[] = { - MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), + MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), + MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), + MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), + MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), + MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), + MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), + MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), + MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), + MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_EMMC_PAD_CTRL), MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL), }; +#endif /* CONFIG_FSL_ESDHC & CONFIG_SPL_BUILD */ iomux_v3_cfg_t const enet_pads[] = { MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), @@ -173,68 +133,123 @@ static void setup_iomux_enet(void) /* mux auxiliary pins to GPIO, so they can be used from the U-Boot cmdline */ iomux_v3_cfg_t const gpio_pads[] = { /* ADDRESS[17:18] [25] used as GPIO */ - MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_KEY_COL2__GPIO4_IO10 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_D1__GPIO2_IO01 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_KEY_COL2__GPIO4_IO10 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_D1__GPIO2_IO01 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, /* ADDRESS[19:24] used as GPIO */ - MX6_PAD_DISP0_DAT23__GPIO5_IO17 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_DISP0_DAT22__GPIO5_IO16 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_DISP0_DAT21__GPIO5_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_DISP0_DAT20__GPIO5_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_DISP0_DAT19__GPIO5_IO13 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_DISP0_DAT18__GPIO5_IO12 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_DISP0_DAT23__GPIO5_IO17 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_DISP0_DAT22__GPIO5_IO16 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_DISP0_DAT21__GPIO5_IO15 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_DISP0_DAT20__GPIO5_IO14 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_DISP0_DAT19__GPIO5_IO13 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_DISP0_DAT18__GPIO5_IO12 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, /* DATA[16:29] [31] used as GPIO */ - MX6_PAD_EIM_LBA__GPIO2_IO27 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_RB0__GPIO6_IO10 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_ALE__GPIO6_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_WP_B__GPIO6_IO09 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_CLE__GPIO6_IO07 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_CSI0_MCLK__GPIO5_IO19 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_CSI0_PIXCLK__GPIO5_IO18 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_EIM_LBA__GPIO2_IO27 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_RB0__GPIO6_IO10 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_ALE__GPIO6_IO08 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_WP_B__GPIO6_IO09 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_CLE__GPIO6_IO07 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_CSI0_MCLK__GPIO5_IO19 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_CSI0_PIXCLK__GPIO5_IO18 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_GPIO_2__GPIO1_IO02 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, /* DQM[0:3] used as GPIO */ - MX6_PAD_EIM_EB0__GPIO2_IO28 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_EB1__GPIO2_IO29 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_SD2_DAT2__GPIO1_IO13 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_EIM_EB0__GPIO2_IO28 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_EB1__GPIO2_IO29 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_SD2_DAT2__GPIO1_IO13 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_D0__GPIO2_IO00 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, /* RDY used as GPIO */ - MX6_PAD_EIM_WAIT__GPIO5_IO00 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_EIM_WAIT__GPIO5_IO00 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, /* ADDRESS[16] DATA[30] used as GPIO */ - MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(WEAK_PULLDOWN), - MX6_PAD_KEY_COL4__GPIO4_IO14 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_KEY_ROW4__GPIO4_IO15 | MUX_PAD_CTRL(WEAK_PULLDOWN) | + MUX_MODE_SION, + MX6_PAD_KEY_COL4__GPIO4_IO14 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, /* CSI pins used as GPIO */ - MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_SD2_CMD__GPIO1_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_D18__GPIO3_IO18 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(WEAK_PULLDOWN), - MX6_PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_A17__GPIO2_IO21 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_A18__GPIO2_IO20 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_EB3__GPIO2_IO31 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_D17__GPIO3_IO17 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_SD2_DAT0__GPIO1_IO15 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_SD2_CMD__GPIO1_IO11 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_D18__GPIO3_IO18 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_A19__GPIO2_IO19 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(WEAK_PULLDOWN) | + MUX_MODE_SION, + MX6_PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_A17__GPIO2_IO21 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_A18__GPIO2_IO20 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_EB3__GPIO2_IO31 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_D17__GPIO3_IO17 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_SD2_DAT0__GPIO1_IO15 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, /* GPIO */ - MX6_PAD_EIM_D26__GPIO3_IO26 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_EIM_D27__GPIO3_IO27 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_D3__GPIO2_IO03 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_ENET_REF_CLK__GPIO1_IO23 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_DI0_PIN4__GPIO4_IO20 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_SD4_DAT3__GPIO2_IO11 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_GPIO_7__GPIO1_IO07 | MUX_PAD_CTRL(WEAK_PULLUP), - MX6_PAD_GPIO_8__GPIO1_IO08 | MUX_PAD_CTRL(WEAK_PULLUP), + MX6_PAD_EIM_D26__GPIO3_IO26 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_EIM_D27__GPIO3_IO27 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_D6__GPIO2_IO06 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_D3__GPIO2_IO03 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_ENET_REF_CLK__GPIO1_IO23 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_DI0_PIN4__GPIO4_IO20 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_SD4_DAT3__GPIO2_IO11 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_NANDF_D4__GPIO2_IO04 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_SD4_DAT0__GPIO2_IO08 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_GPIO_7__GPIO1_IO07 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, + MX6_PAD_GPIO_8__GPIO1_IO08 | MUX_PAD_CTRL(WEAK_PULLUP) | + MUX_MODE_SION, /* USBH_OC */ MX6_PAD_EIM_D30__GPIO3_IO30 | MUX_PAD_CTRL(WEAK_PULLUP), /* USBC_ID */ @@ -249,8 +264,8 @@ static void setup_iomux_gpio(void) } iomux_v3_cfg_t const usb_pads[] = { - /* USB_PE */ - MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL), + /* USBH_PEN */ + MX6_PAD_EIM_D31__GPIO3_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL) | MUX_MODE_SION, # define GPIO_USBH_EN IMX_GPIO_NR(3, 31) }; @@ -258,14 +273,21 @@ iomux_v3_cfg_t const usb_pads[] = { * UARTs are used in DTE mode, switch the mode on all UARTs before * any pinmuxing connects a (DCE) output to a transceiver output. */ +#define UCR3 0x88 /* FIFO Control Register */ +#define UCR3_RI BIT(8) /* RIDELT DTE mode */ +#define UCR3_DCD BIT(9) /* DCDDELT DTE mode */ #define UFCR 0x90 /* FIFO Control Register */ -#define UFCR_DCEDTE (1<<6) /* DCE=0 */ +#define UFCR_DCEDTE BIT(6) /* DCE=0 */ static void setup_dtemode_uart(void) { setbits_le32((u32 *)(UART1_BASE + UFCR), UFCR_DCEDTE); setbits_le32((u32 *)(UART2_BASE + UFCR), UFCR_DCEDTE); setbits_le32((u32 *)(UART3_BASE + UFCR), UFCR_DCEDTE); + + clrbits_le32((u32 *)(UART1_BASE + UCR3), UCR3_DCD | UCR3_RI); + clrbits_le32((u32 *)(UART2_BASE + UCR3), UCR3_DCD | UCR3_RI); + clrbits_le32((u32 *)(UART3_BASE + UCR3), UCR3_DCD | UCR3_RI); } static void setup_iomux_uart(void) @@ -280,29 +302,9 @@ int board_ehci_hcd_init(int port) imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads)); return 0; } - -int board_ehci_power(int port, int on) -{ - switch (port) { - case 0: - /* control OTG power */ - /* No special PE for USBC, always on when ID pin signals - host mode */ - break; - case 1: - /* Control MXM USBH */ - /* Set MXM USBH power enable, '0' means on */ - gpio_direction_output(GPIO_USBH_EN, !on); - mdelay(100); - break; - default: - break; - } - return 0; -} #endif -#ifdef CONFIG_FSL_ESDHC +#if defined(CONFIG_FSL_ESDHC) && defined(CONFIG_SPL_BUILD) /* use the following sequence: eMMC, MMC */ struct fsl_esdhc_cfg usdhc_cfg[CONFIG_SYS_FSL_USDHC_NUM] = { {USDHC3_BASE_ADDR}, @@ -316,6 +318,7 @@ int board_mmc_getcd(struct mmc *mmc) switch (cfg->esdhc_base) { case USDHC1_BASE_ADDR: + gpio_request(GPIO_MMC_CD, "MMC_CD"); gpio_direction_input(GPIO_MMC_CD); ret = !gpio_get_value(GPIO_MMC_CD); break; @@ -326,37 +329,6 @@ int board_mmc_getcd(struct mmc *mmc) int board_mmc_init(bd_t *bis) { -#ifndef CONFIG_SPL_BUILD - s32 status = 0; - u32 index = 0; - - usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); - usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK); - - usdhc_cfg[0].max_bus_width = 8; - usdhc_cfg[1].max_bus_width = 4; - - for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) { - switch (index) { - case 0: - imx_iomux_v3_setup_multiple_pads( - usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); - break; - case 1: - imx_iomux_v3_setup_multiple_pads( - usdhc1_pads, ARRAY_SIZE(usdhc1_pads)); - break; - default: - printf("Warning: you configured more USDHC controllers (%d) then supported by the board (%d)\n", - index + 1, CONFIG_SYS_FSL_USDHC_NUM); - return status; - } - - status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]); - } - - return status; -#else struct src *psrc = (struct src *)SRC_BASE_ADDR; unsigned reg = readl(&psrc->sbmr1) >> 11; /* @@ -388,9 +360,8 @@ int board_mmc_init(bd_t *bis) } return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); -#endif } -#endif +#endif /* CONFIG_FSL_ESDHC & CONFIG_SPL_BUILD */ int board_phy_config(struct phy_device *phydev) { @@ -412,6 +383,7 @@ int board_eth_init(bd_t *bis) ret = enable_fec_anatop_clock(0, ENET_50MHZ); if (ret) return ret; + /* set gpr1[ENET_CLK_SEL] */ setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK); @@ -421,6 +393,7 @@ int board_eth_init(bd_t *bis) bus = fec_get_miibus(base, -1); if (!bus) return 0; + /* scan PHY 1..7 */ phydev = phy_find_by_mask(bus, 0xff, PHY_INTERFACE_MODE_RMII); if (!phydev) { @@ -428,6 +401,7 @@ int board_eth_init(bd_t *bis) puts("no PHY found\n"); return 0; } + phy_reset(phydev); printf("using PHY at %d\n", phydev->addr); ret = fec_probe(bis, -1, base, bus, phydev); @@ -436,7 +410,8 @@ int board_eth_init(bd_t *bis) free(phydev); free(bus); } -#endif +#endif /* CONFIG_FEC_MXC */ + return 0; } @@ -452,11 +427,12 @@ static iomux_v3_cfg_t const pwr_intb_pads[] = { static iomux_v3_cfg_t const backlight_pads[] = { /* Backlight On */ - MX6_PAD_EIM_D26__GPIO3_IO26 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_EIM_D26__GPIO3_IO26 | MUX_PAD_CTRL(NO_PAD_CTRL) | MUX_MODE_SION, #define RGB_BACKLIGHT_GP IMX_GPIO_NR(3, 26) /* Backlight PWM, used as GPIO in U-Boot */ MX6_PAD_EIM_A22__GPIO2_IO16 | MUX_PAD_CTRL(NO_PULLUP), - MX6_PAD_SD4_DAT1__GPIO2_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL), + MX6_PAD_SD4_DAT1__GPIO2_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL) | + MUX_MODE_SION, #define RGB_BACKLIGHTPWM_GP IMX_GPIO_NR(2, 9) }; @@ -619,6 +595,8 @@ static void setup_display(void) imx_iomux_v3_setup_multiple_pads(backlight_pads, ARRAY_SIZE(backlight_pads)); /* use 0 for EDT 7", use 1 for LG fullHD panel */ + gpio_request(RGB_BACKLIGHTPWM_GP, "PWM<A>"); + gpio_request(RGB_BACKLIGHT_GP, "BL_ON"); gpio_direction_output(RGB_BACKLIGHTPWM_GP, 0); gpio_direction_output(RGB_BACKLIGHT_GP, 1); } @@ -656,9 +634,6 @@ int board_init(void) /* address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; - setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); - setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info_loc); - #if defined(CONFIG_VIDEO_IPUV3) setup_display(); #endif @@ -689,16 +664,17 @@ int board_late_init(void) env_set("board_rev", env_str); #endif - return 0; -} -#endif /* CONFIG_BOARD_LATE_INIT */ +#ifdef CONFIG_CMD_USB_SDP + if (is_boot_from_usb()) { + printf("Serial Downloader recovery mode, using sdp command\n"); + env_set("bootdelay", "0"); + env_set("bootcmd", "sdp 0"); + } +#endif /* CONFIG_CMD_USB_SDP */ -#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_SYSTEM_SETUP) -int ft_system_setup(void *blob, bd_t *bd) -{ return 0; } -#endif +#endif /* CONFIG_BOARD_LATE_INIT */ int checkboard(void) { @@ -722,7 +698,18 @@ int checkboard(void) #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) int ft_board_setup(void *blob, bd_t *bd) { - return ft_common_board_setup(blob, bd); + u32 cma_size; + + ft_common_board_setup(blob, bd); + + cma_size = env_get_ulong("cma-size", 10, 320 * 1024 * 1024); + cma_size = min((u32)(gd->ram_size >> 1), cma_size); + + fdt_setprop_u32(blob, + fdt_path_offset(blob, "/reserved-memory/linux,cma"), + "size", + cma_size); + return 0; } #endif @@ -1073,6 +1060,7 @@ static void spl_dram_init(void) case TEMP_AUTOMOTIVE: default: if (is_cpu_type(MXC_CPU_MX6DL)) { + puts("Industrial temperature grade DDR3 timings, 64bit bus width.\n"); ddr_init(mx6dl_dcd_table, ARRAY_SIZE(mx6dl_dcd_table)); } else { puts("Industrial temperature grade DDR3 timings, 32bit bus width.\n"); @@ -1083,6 +1071,26 @@ static void spl_dram_init(void) udelay(100); } +static iomux_v3_cfg_t const gpio_reset_pad[] = { + MX6_PAD_RGMII_RD1__GPIO6_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL) | + MUX_MODE_SION +#define GPIO_NRESET IMX_GPIO_NR(6, 27) +}; + +#define IMX_RESET_CAUSE_POR 0x00011 +static void nreset_out(void) +{ + int reset_cause = get_imx_reset_cause(); + + if (reset_cause != IMX_RESET_CAUSE_POR) { + imx_iomux_v3_setup_multiple_pads(gpio_reset_pad, + ARRAY_SIZE(gpio_reset_pad)); + gpio_direction_output(GPIO_NRESET, 1); + udelay(100); + gpio_direction_output(GPIO_NRESET, 0); + } +} + void board_init_f(ulong dummy) { /* setup AIPS and disable watchdog */ @@ -1091,7 +1099,7 @@ void board_init_f(ulong dummy) ccgr_init(); gpr_init(); - /* iomux and setup of i2c */ + /* iomux */ board_early_init_f(); /* setup GP timer */ @@ -1109,6 +1117,9 @@ void board_init_f(ulong dummy) /* Clear the BSS. */ memset(__bss_start, 0, __bss_end - __bss_start); + /* Assert nReset_Out */ + nreset_out(); + /* load/boot image from boot device */ board_init_r(NULL, 0); } @@ -1117,7 +1128,7 @@ void reset_cpu(ulong addr) { } -#endif +#endif /* CONFIG_SPL_BUILD */ static struct mxc_serial_platdata mxc_serial_plat = { .reg = (struct mxc_uart *)UART1_BASE, diff --git a/board/toradex/colibri_imx6/colibri_imx6.cfg b/board/toradex/colibri_imx6/colibri_imx6.cfg deleted file mode 100644 index 517c5eb107..0000000000 --- a/board/toradex/colibri_imx6/colibri_imx6.cfg +++ /dev/null @@ -1,37 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2013 Boundary Devices - * Copyright (C) 2014 Toradex AG - * - * Refer doc/README.imximage for more details about how-to configure - * and create imximage boot image - * - * The syntax is taken as close as possible with the kwbimage - */ - -/* image version */ -IMAGE_VERSION 2 - -/* - * Boot Device : one of - * spi, sd (the board has no nand neither onenand) - */ -BOOT_FROM sd - -#define __ASSEMBLY__ -#include <config.h> -#include "asm/arch/mx6-ddr.h" -#include "asm/arch/iomux.h" -#include "asm/arch/crm_regs.h" - -#include "ddr-setup.cfg" - -#if CONFIG_DDR_MB == 256 -#include "800mhz_2x64mx16.cfg" -#elif CONFIG_DDR_MB == 512 -#include "800mhz_4x64mx16.cfg" -#else -#error "unknown DDR size" -#endif - -#include "clocks.cfg" diff --git a/board/toradex/colibri_imx6/ddr-setup.cfg b/board/toradex/colibri_imx6/ddr-setup.cfg deleted file mode 100644 index a943fd228c..0000000000 --- a/board/toradex/colibri_imx6/ddr-setup.cfg +++ /dev/null @@ -1,97 +0,0 @@ -/* SPDX-License-Identifier: GPL-2.0+ */ -/* - * Copyright (C) 2013 Boundary Devices - * Copyright (C) 2014-2016, Toradex AG - * - * Device Configuration Data (DCD) - * - * Each entry must have the format: - * Addr-type Address Value - * - * where: - * Addr-type register length (1,2 or 4 bytes) - * Address absolute address of the register - * value value to be stored in the register - */ - -/* - * DDR3 settings - * MX6Q ddr is limited to 1066 Mhz currently 1056 MHz(528 MHz clock), - * memory bus width: 64 bits x16/x32/x64 - * MX6DL ddr is limited to 800 MHz(400 MHz clock) - * memory bus width: 64 bits x16/x32/x64 - * MX6SOLO ddr is limited to 800 MHz(400 MHz clock) - * memory bus width: 32 bits x16/x32 - */ -DATA 4, MX6_IOM_DRAM_SDQS0, 0x00000030 -DATA 4, MX6_IOM_DRAM_SDQS1, 0x00000030 -DATA 4, MX6_IOM_DRAM_SDQS2, 0x00000030 -DATA 4, MX6_IOM_DRAM_SDQS3, 0x00000030 -DATA 4, MX6_IOM_DRAM_SDQS4, 0x00000030 -DATA 4, MX6_IOM_DRAM_SDQS5, 0x00000030 -DATA 4, MX6_IOM_DRAM_SDQS6, 0x00000030 -DATA 4, MX6_IOM_DRAM_SDQS7, 0x00000030 - -DATA 4, MX6_IOM_GRP_B0DS, 0x00000030 -DATA 4, MX6_IOM_GRP_B1DS, 0x00000030 -DATA 4, MX6_IOM_GRP_B2DS, 0x00000030 -DATA 4, MX6_IOM_GRP_B3DS, 0x00000030 -DATA 4, MX6_IOM_GRP_B4DS, 0x00000030 -DATA 4, MX6_IOM_GRP_B5DS, 0x00000030 -DATA 4, MX6_IOM_GRP_B6DS, 0x00000030 -DATA 4, MX6_IOM_GRP_B7DS, 0x00000030 -DATA 4, MX6_IOM_GRP_ADDDS, 0x00000030 -/* 40 Ohm drive strength for cs0/1,sdba2,cke0/1,sdwe */ -DATA 4, MX6_IOM_GRP_CTLDS, 0x00000030 - -DATA 4, MX6_IOM_DRAM_DQM0, 0x00020030 -DATA 4, MX6_IOM_DRAM_DQM1, 0x00020030 -DATA 4, MX6_IOM_DRAM_DQM2, 0x00020030 -DATA 4, MX6_IOM_DRAM_DQM3, 0x00020030 -DATA 4, MX6_IOM_DRAM_DQM4, 0x00020030 -DATA 4, MX6_IOM_DRAM_DQM5, 0x00020030 -DATA 4, MX6_IOM_DRAM_DQM6, 0x00020030 -DATA 4, MX6_IOM_DRAM_DQM7, 0x00020030 - -DATA 4, MX6_IOM_DRAM_CAS, 0x00020030 -DATA 4, MX6_IOM_DRAM_RAS, 0x00020030 -DATA 4, MX6_IOM_DRAM_SDCLK_0, 0x00020030 -DATA 4, MX6_IOM_DRAM_SDCLK_1, 0x00020030 - -DATA 4, MX6_IOM_DRAM_RESET, 0x00020030 -DATA 4, MX6_IOM_DRAM_SDCKE0, 0x00003000 -DATA 4, MX6_IOM_DRAM_SDCKE1, 0x00003000 - -DATA 4, MX6_IOM_DRAM_SDODT0, 0x00003030 -DATA 4, MX6_IOM_DRAM_SDODT1, 0x00003030 - -/* (differential input) */ -DATA 4, MX6_IOM_DDRMODE_CTL, 0x00020000 -/* (differential input) */ -DATA 4, MX6_IOM_GRP_DDRMODE, 0x00020000 -/* disable ddr pullups */ -DATA 4, MX6_IOM_GRP_DDRPKE, 0x00000000 -DATA 4, MX6_IOM_DRAM_SDBA2, 0x00000000 -/* 40 Ohm drive strength for cs0/1,sdba2,cke0/1,sdwe */ -DATA 4, MX6_IOM_GRP_DDR_TYPE, 0x000C0000 - -/* Read data DQ Byte0-3 delay */ -DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333 -DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333 -DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333 -DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333 -DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333 -DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333 -DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333 -DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333 - -/* - * MDMISC mirroring interleaved (row/bank/col) - */ -/* TODO: check what the RALAT field does */ -DATA 4, MX6_MMDC_P0_MDMISC, 0x00081740 - -/* - * MDSCR con_req - */ -DATA 4, MX6_MMDC_P0_MDSCR, 0x00008000 diff --git a/board/toradex/colibri_imx6/do_fuse.c b/board/toradex/colibri_imx6/do_fuse.c index e6793e366a..22d191f52a 100644 --- a/board/toradex/colibri_imx6/do_fuse.c +++ b/board/toradex/colibri_imx6/do_fuse.c @@ -29,7 +29,7 @@ static int mfgr_fuse(void) return CMD_RET_FAILURE; } /* boot cfg */ - fuse_prog(0, 5, 0x00005072); + fuse_prog(0, 5, 0x00005062); /* BT_FUSE_SEL */ fuse_prog(0, 6, 0x00000010); return CMD_RET_SUCCESS; diff --git a/board/toradex/colibri_imx6/pf0100.c b/board/toradex/colibri_imx6/pf0100.c index fa63865670..e744243297 100644 --- a/board/toradex/colibri_imx6/pf0100.c +++ b/board/toradex/colibri_imx6/pf0100.c @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0+ /* - * Copyright (C) 2014-2016, Toradex AG + * Copyright (C) 2014-2019, Toradex AG */ /* @@ -21,6 +21,8 @@ /* define for PMIC register dump */ /*#define DEBUG */ +#define WARNBAR "@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@\n" + /* use GPIO: EXT_IO1 to switch on VPGM, ON: 1 */ static __maybe_unused iomux_v3_cfg_t const pmic_prog_pads[] = { MX6_PAD_NANDF_D3__GPIO2_IO03 | MUX_PAD_CTRL(NO_PAD_CTRL), @@ -29,37 +31,128 @@ static __maybe_unused iomux_v3_cfg_t const pmic_prog_pads[] = { unsigned pmic_init(void) { + int rc; + struct udevice *dev = NULL; unsigned programmed = 0; uchar bus = 1; uchar devid, revid, val; - puts("PMIC: "); - if (!((0 == i2c_set_bus_num(bus)) && - (0 == i2c_probe(PFUZE100_I2C_ADDR)))) { - puts("i2c bus failed\n"); + puts("PMIC: "); + rc = i2c_get_chip_for_busnum(bus, PFUZE100_I2C_ADDR, 1, &dev); + if (rc) { + printf("failed to get device for PMIC at address 0x%x\n", + PFUZE100_I2C_ADDR); + return 0; + } + + /* check for errors in PMIC fuses */ + if (dm_i2c_read(dev, PFUZE100_INTSTAT3, &val, 1) < 0) { + puts("i2c pmic INTSTAT3 register read failed\n"); return 0; } + if (val & PFUZE100_BIT_OTP_ECCI) { + puts("\n" WARNBAR); + puts("WARNING: ecc errors found in pmic fuse banks\n"); + puts(WARNBAR); + } + if (dm_i2c_read(dev, PFUZE100_OTP_ECC_SE1, &val, 1) < 0) { + puts("i2c pmic ECC_SE1 register read failed\n"); + return 0; + } + if (val & PFUZE100_BITS_ECC_SE1) { + puts(WARNBAR); + puts("WARNING: ecc has made bit corrections in banks 1 to 5\n"); + puts(WARNBAR); + } + if (dm_i2c_read(dev, PFUZE100_OTP_ECC_SE2, &val, 1) < 0) { + puts("i2c pmic ECC_SE2 register read failed\n"); + return 0; + } + if (val & PFUZE100_BITS_ECC_SE2) { + puts(WARNBAR); + puts("WARNING: ecc has made bit corrections in banks 6 to 10\n" + ); + puts(WARNBAR); + } + if (dm_i2c_read(dev, PFUZE100_OTP_ECC_DE1, &val, 1) < 0) { + puts("i2c pmic ECC_DE register read failed\n"); + return 0; + } + if (val & PFUZE100_BITS_ECC_DE1) { + puts(WARNBAR); + puts("ERROR: banks 1 to 5 have uncorrectable bits\n"); + puts(WARNBAR); + } + if (dm_i2c_read(dev, PFUZE100_OTP_ECC_DE2, &val, 1) < 0) { + puts("i2c pmic ECC_DE register read failed\n"); + return 0; + } + if (val & PFUZE100_BITS_ECC_DE2) { + puts(WARNBAR); + puts("ERROR: banks 6 to 10 have uncorrectable bits\n"); + puts(WARNBAR); + } + /* get device ident */ - if (i2c_read(PFUZE100_I2C_ADDR, PFUZE100_DEVICEID, 1, &devid, 1) < 0) { + if (dm_i2c_read(dev, PFUZE100_DEVICEID, &devid, 1) < 0) { puts("i2c pmic devid read failed\n"); return 0; } - if (i2c_read(PFUZE100_I2C_ADDR, PFUZE100_REVID, 1, &revid, 1) < 0) { + if (dm_i2c_read(dev, PFUZE100_REVID, &revid, 1) < 0) { puts("i2c pmic revid read failed\n"); return 0; } - printf("device id: 0x%.2x, revision id: 0x%.2x\n", devid, revid); + printf("device id: 0x%.2x, revision id: 0x%.2x, ", devid, revid); + + /* get device programmed state */ + val = PFUZE100_PAGE_REGISTER_PAGE1; + if (dm_i2c_write(dev, PFUZE100_PAGE_REGISTER, &val, 1)) { + puts("i2c write failed\n"); + return 0; + } + if (dm_i2c_read(dev, PFUZE100_FUSE_POR1, &val, 1) < 0) { + puts("i2c fuse_por read failed\n"); + return 0; + } + if (val & PFUZE100_FUSE_POR_M) + programmed++; + + if (dm_i2c_read(dev, PFUZE100_FUSE_POR2, &val, 1) < 0) { + puts("i2c fuse_por read failed\n"); + return programmed; + } + if (val & PFUZE100_FUSE_POR_M) + programmed++; + + if (dm_i2c_read(dev, PFUZE100_FUSE_POR3, &val, 1) < 0) { + puts("i2c fuse_por read failed\n"); + return programmed; + } + if (val & PFUZE100_FUSE_POR_M) + programmed++; + + switch (programmed) { + case 0: + puts("not programmed\n"); + break; + case 3: + puts("programmed\n"); + break; + default: + puts("undefined programming state\n"); + break; + } #ifdef DEBUG { - unsigned i, j; + unsigned int i, j; for (i = 0; i < 16; i++) printf("\t%x", i); for (j = 0; j < 0x80; ) { printf("\n%2x", j); for (i = 0; i < 16; i++) { - i2c_read(PFUZE100_I2C_ADDR, j+i, 1, &val, 1); + dm_i2c_read(dev, j + i, &val, 1); printf("\t%2x", val); } j += 0x10; @@ -67,8 +160,7 @@ unsigned pmic_init(void) printf("\nEXT Page 1"); val = PFUZE100_PAGE_REGISTER_PAGE1; - if (i2c_write(PFUZE100_I2C_ADDR, PFUZE100_PAGE_REGISTER, 1, - &val, 1)) { + if (dm_i2c_write(dev, PFUZE100_PAGE_REGISTER, &val, 1)) { puts("i2c write failed\n"); return 0; } @@ -76,7 +168,7 @@ unsigned pmic_init(void) for (j = 0x80; j < 0x100; ) { printf("\n%2x", j); for (i = 0; i < 16; i++) { - i2c_read(PFUZE100_I2C_ADDR, j+i, 1, &val, 1); + dm_i2c_read(dev, j + i, &val, 1); printf("\t%2x", val); } j += 0x10; @@ -84,8 +176,7 @@ unsigned pmic_init(void) printf("\nEXT Page 2"); val = PFUZE100_PAGE_REGISTER_PAGE2; - if (i2c_write(PFUZE100_I2C_ADDR, PFUZE100_PAGE_REGISTER, 1, - &val, 1)) { + if (dm_i2c_write(dev, PFUZE100_PAGE_REGISTER, &val, 1)) { puts("i2c write failed\n"); return 0; } @@ -93,52 +184,14 @@ unsigned pmic_init(void) for (j = 0x80; j < 0x100; ) { printf("\n%2x", j); for (i = 0; i < 16; i++) { - i2c_read(PFUZE100_I2C_ADDR, j+i, 1, &val, 1); + dm_i2c_read(dev, j + i, &val, 1); printf("\t%2x", val); } j += 0x10; } printf("\n"); } -#endif - /* get device programmed state */ - val = PFUZE100_PAGE_REGISTER_PAGE1; - if (i2c_write(PFUZE100_I2C_ADDR, PFUZE100_PAGE_REGISTER, 1, &val, 1)) { - puts("i2c write failed\n"); - return 0; - } - if (i2c_read(PFUZE100_I2C_ADDR, PFUZE100_FUSE_POR1, 1, &val, 1) < 0) { - puts("i2c fuse_por read failed\n"); - return 0; - } - if (val & PFUZE100_FUSE_POR_M) - programmed++; - - if (i2c_read(PFUZE100_I2C_ADDR, PFUZE100_FUSE_POR2, 1, &val, 1) < 0) { - puts("i2c fuse_por read failed\n"); - return programmed; - } - if (val & PFUZE100_FUSE_POR_M) - programmed++; - - if (i2c_read(PFUZE100_I2C_ADDR, PFUZE100_FUSE_POR3, 1, &val, 1) < 0) { - puts("i2c fuse_por read failed\n"); - return programmed; - } - if (val & PFUZE100_FUSE_POR_M) - programmed++; - - switch (programmed) { - case 0: - printf("PMIC: not programmed\n"); - break; - case 3: - printf("PMIC: programmed\n"); - break; - default: - printf("PMIC: undefined programming state\n"); - break; - } +#endif /* DEBUG */ return programmed; } @@ -146,6 +199,8 @@ unsigned pmic_init(void) #ifndef CONFIG_SPL_BUILD static int pf0100_prog(void) { + int rc; + struct udevice *dev = NULL; unsigned char bus = 1; unsigned char val; unsigned int i; @@ -159,9 +214,10 @@ static int pf0100_prog(void) ARRAY_SIZE(pmic_prog_pads)); gpio_direction_output(PMIC_PROG_VOLTAGE, 0); - if (!((0 == i2c_set_bus_num(bus)) && - (0 == i2c_probe(PFUZE100_I2C_ADDR)))) { - puts("i2c bus failed\n"); + rc = i2c_get_chip_for_busnum(bus, PFUZE100_I2C_ADDR, 1, &dev); + if (rc) { + printf("failed to get device for PMIC at address 0x%x\n", + PFUZE100_I2C_ADDR); return CMD_RET_FAILURE; } @@ -169,8 +225,7 @@ static int pf0100_prog(void) switch (pmic_otp_prog[i].cmd) { case pmic_i2c: val = (unsigned char) (pmic_otp_prog[i].value & 0xff); - if (i2c_write(PFUZE100_I2C_ADDR, pmic_otp_prog[i].reg, - 1, &val, 1)) { + if (dm_i2c_write(dev, pmic_otp_prog[i].reg, &val, 1)) { printf("i2c write failed, reg 0x%2x, value 0x%2x\n", pmic_otp_prog[i].reg, val); return CMD_RET_FAILURE; @@ -209,4 +264,4 @@ U_BOOT_CMD( "Program the OTP fuses on the PMIC PF0100", "" ); -#endif +#endif /* CONFIG_SPL_BUILD */ diff --git a/board/toradex/colibri_imx6/pf0100.h b/board/toradex/colibri_imx6/pf0100.h index c0efb79bbc..9257620511 100644 --- a/board/toradex/colibri_imx6/pf0100.h +++ b/board/toradex/colibri_imx6/pf0100.h @@ -1,6 +1,6 @@ /* SPDX-License-Identifier: GPL-2.0+ */ /* - * Copyright (C) 2014-2016, Toradex AG + * Copyright (C) 2014-2019, Toradex AG */ /* @@ -10,11 +10,23 @@ #ifndef PF0100_H_ #define PF0100_H_ +/* bit definitions */ +#define PFUZE100_BIT_0 (0x01 << 0) +#define PFUZE100_BIT_1 (0x01 << 1) +#define PFUZE100_BIT_2 (0x01 << 2) +#define PFUZE100_BIT_3 (0x01 << 3) +#define PFUZE100_BIT_4 (0x01 << 4) +#define PFUZE100_BIT_5 (0x01 << 5) +#define PFUZE100_BIT_6 (0x01 << 6) +#define PFUZE100_BIT_7 (0x01 << 7) + /* 7-bit I2C bus slave address */ #define PFUZE100_I2C_ADDR (0x08) /* Register Addresses */ #define PFUZE100_DEVICEID (0x0) #define PFUZE100_REVID (0x3) +#define PFUZE100_INTSTAT3 (0xe) +#define PFUZE100_BIT_OTP_ECCI PFUZE100_BIT_7 #define PFUZE100_SW1AMODE (0x23) #define PFUZE100_SW1ACON 36 #define PFUZE100_SW1ACON_SPEED_VAL (0x1<<6) /*default */ @@ -39,12 +51,55 @@ #define PFUZE100_PAGE_REGISTER_PAGE2 (0x02 & PFUZE100_PAGE_REGISTER_PAGE_M) /* extended page 1 */ +#define PFUZE100_OTP_ECC_SE1 0x8a +#define PFUZE100_BIT_ECC1_SE PFUZE100_BIT_0 +#define PFUZE100_BIT_ECC2_SE PFUZE100_BIT_1 +#define PFUZE100_BIT_ECC3_SE PFUZE100_BIT_2 +#define PFUZE100_BIT_ECC4_SE PFUZE100_BIT_3 +#define PFUZE100_BIT_ECC5_SE PFUZE100_BIT_4 +#define PFUZE100_BITS_ECC_SE1 ((PFUZE100_BIT_ECC1_SE) | \ + (PFUZE100_BIT_ECC2_SE) | \ + (PFUZE100_BIT_ECC3_SE) | \ + (PFUZE100_BIT_ECC4_SE) | \ + (PFUZE100_BIT_ECC5_SE)) +#define PFUZE100_OTP_ECC_SE2 0x8b +#define PFUZE100_BIT_ECC6_SE PFUZE100_BIT_0 +#define PFUZE100_BIT_ECC7_SE PFUZE100_BIT_1 +#define PFUZE100_BIT_ECC8_SE PFUZE100_BIT_2 +#define PFUZE100_BIT_ECC9_SE PFUZE100_BIT_3 +#define PFUZE100_BIT_ECC10_SE PFUZE100_BIT_4 +#define PFUZE100_BITS_ECC_SE2 ((PFUZE100_BIT_ECC6_SE) | \ + (PFUZE100_BIT_ECC7_SE) | \ + (PFUZE100_BIT_ECC8_SE) | \ + (PFUZE100_BIT_ECC9_SE) | \ + (PFUZE100_BIT_ECC10_SE)) +#define PFUZE100_OTP_ECC_DE1 0x8c +#define PFUZE100_BIT_ECC1_DE PFUZE100_BIT_0 +#define PFUZE100_BIT_ECC2_DE PFUZE100_BIT_1 +#define PFUZE100_BIT_ECC3_DE PFUZE100_BIT_2 +#define PFUZE100_BIT_ECC4_DE PFUZE100_BIT_3 +#define PFUZE100_BIT_ECC5_DE PFUZE100_BIT_4 +#define PFUZE100_BITS_ECC_DE1 ((PFUZE100_BIT_ECC1_DE) | \ + (PFUZE100_BIT_ECC2_DE) | \ + (PFUZE100_BIT_ECC3_DE) | \ + (PFUZE100_BIT_ECC4_DE) | \ + (PFUZE100_BIT_ECC5_DE)) +#define PFUZE100_OTP_ECC_DE2 0x8d +#define PFUZE100_BIT_ECC6_DE PFUZE100_BIT_0 +#define PFUZE100_BIT_ECC7_DE PFUZE100_BIT_1 +#define PFUZE100_BIT_ECC8_DE PFUZE100_BIT_2 +#define PFUZE100_BIT_ECC9_DE PFUZE100_BIT_3 +#define PFUZE100_BIT_ECC10_DE PFUZE100_BIT_4 +#define PFUZE100_BITS_ECC_DE2 ((PFUZE100_BIT_ECC6_DE) | \ + (PFUZE100_BIT_ECC7_DE) | \ + (PFUZE100_BIT_ECC8_DE) | \ + (PFUZE100_BIT_ECC9_DE) | \ + (PFUZE100_BIT_ECC10_DE)) #define PFUZE100_FUSE_POR1 0xe4 #define PFUZE100_FUSE_POR2 0xe5 #define PFUZE100_FUSE_POR3 0xe6 #define PFUZE100_FUSE_POR_M (0x1 << 1) - /* output some informational messages, return the number FUSE_POR=1 */ /* i.e. 0: unprogrammed, 3: programmed, other: undefined prog. state */ unsigned pmic_init(void); diff --git a/board/toradex/colibri_imx6/pf0100_otp.inc b/board/toradex/colibri_imx6/pf0100_otp.inc index ce29b95ae2..c3b1f67f81 100644 --- a/board/toradex/colibri_imx6/pf0100_otp.inc +++ b/board/toradex/colibri_imx6/pf0100_otp.inc @@ -5,16 +5,17 @@ // Register Output for PF0100 programmer // Customer: Toradex AG -// Program: Colibri iMX6 +// Program: Colibri iMX6 V1.1 // Sample marking: -// Date: 24.07.2015 -// Time: 10:52:58 +// Date: 01.05.2017 +// Time: 16:22:32 // Generated from Spreadsheet Revision: P1.8 -/* sed commands to get from programmer script to struct */ +/* sed commands to get from programmer script to struct content */ /* sed -e 's/^WRITE_I2C:\(..\):\(..\)/\{pmic_i2c, 0x\1, 0x\2\},/g' -e 's/^DELAY:\([0-9]*\)/\{pmic_delay, 0, \1\},/g' pf0100_otp_Colibri_iMX6.txt > pf0100_otp.inc sed -i -e 's/^VPGM:ON/\{pmic_vpgm, 0, 1},/g' -e 's/^VPGM:OFF/\{pmic_vpgm, 0, 0},/g' pf0100_otp.inc - sed -i -e 's/^PWRON: HIGH/\{pmic_pwr, 0, 1},/g' -e 's/^PWRON:LOW/\{pmic_pwr, 0, 0},/g' pf0100_otp.inc */ + sed -i -e 's/^PWRON: HIGH/\{pmic_pwr, 0, 1},/g' -e 's/^PWRON:LOW/\{pmic_pwr, 0, 0},/g' pf0100_otp.inc +*/ enum { pmic_i2c, pmic_delay, pmic_vpgm, pmic_pwr }; struct pmic_otp_prog_t{ @@ -47,7 +48,8 @@ struct pmic_otp_prog_t pmic_otp_prog[] = { {pmic_i2c, 0xC8, 0x0E}, // Auto gen from Row134 {pmic_i2c, 0xCC, 0x0E}, // Auto gen from Row138 {pmic_i2c, 0xCD, 0x05}, // Auto gen from Row139 -{pmic_i2c, 0xD0, 0x0C}, // Auto gen from Row142 +{pmic_i2c, 0xD0, 0x0F}, // Auto gen from Row142 +{pmic_i2c, 0xD1, 0x05}, // Auto gen from Row143 {pmic_i2c, 0xD5, 0x07}, // Auto gen from Row147 {pmic_i2c, 0xD8, 0x07}, // Auto gen from Row150 {pmic_i2c, 0xD9, 0x06}, // Auto gen from Row151 @@ -185,4 +187,4 @@ struct pmic_otp_prog_t pmic_otp_prog[] = { {pmic_delay, 0, 500}, {pmic_pwr, 0, 1}, #endif -};
\ No newline at end of file +}; |