diff options
Diffstat (limited to 'board/trab/cmd_trab.c')
| -rw-r--r-- | board/trab/cmd_trab.c | 24 |
1 files changed, 12 insertions, 12 deletions
diff --git a/board/trab/cmd_trab.c b/board/trab/cmd_trab.c index daa6aeefc7..7e2a672348 100644 --- a/board/trab/cmd_trab.c +++ b/board/trab/cmd_trab.c @@ -168,7 +168,7 @@ int do_burn_in (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) int cycle_status; if (argc > 1) { - printf ("Usage:\n%s\n", cmdtp->usage); + cmd_usage(cmdtp); return 1; } @@ -258,7 +258,7 @@ int do_burn_in (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) U_BOOT_CMD( burn_in, 1, 1, do_burn_in, - "burn_in - start burn-in test application on TRAB\n", + "start burn-in test application on TRAB", "\n" " - start burn-in test application\n" " The burn-in test could took a while to finish!\n" @@ -271,7 +271,7 @@ int do_dip (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) int i, dip; if (argc > 1) { - printf ("Usage:\n%s\n", cmdtp->usage); + cmd_usage(cmdtp); return 1; } @@ -292,7 +292,7 @@ int do_dip (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) U_BOOT_CMD( dip, 1, 1, do_dip, - "dip - read dip switch on TRAB\n", + "read dip switch on TRAB", "\n" " - read state of dip switch (S1) on TRAB board\n" " read sequence: 1-2-3-4; ON=1; OFF=0; e.g.: \"0100\"\n" @@ -304,7 +304,7 @@ int do_vcc5v (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) int vcc5v; if (argc > 1) { - printf ("Usage:\n%s\n", cmdtp->usage); + cmd_usage(cmdtp); return 1; } @@ -321,7 +321,7 @@ int do_vcc5v (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) U_BOOT_CMD( vcc5v, 1, 1, do_vcc5v, - "vcc5v - read VCC5V on TRAB\n", + "read VCC5V on TRAB", "\n" " - read actual value of voltage VCC5V\n" ); @@ -332,7 +332,7 @@ int do_contact_temp (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) int contact_temp; if (argc > 1) { - printf ("Usage:\n%s\n", cmdtp->usage); + cmd_usage(cmdtp); return 1; } @@ -346,7 +346,7 @@ int do_contact_temp (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) U_BOOT_CMD( c_temp, 1, 1, do_contact_temp, - "c_temp - read contact temperature on TRAB\n", + "read contact temperature on TRAB", "\n" " - reads the onboard temperature (=contact temperature)\n" ); @@ -355,7 +355,7 @@ U_BOOT_CMD( int do_burn_in_status (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) { if (argc > 1) { - printf ("Usage:\n%s\n", cmdtp->usage); + cmd_usage(cmdtp); return 1; } @@ -398,7 +398,7 @@ int do_burn_in_status (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) U_BOOT_CMD( bis, 1, 1, do_burn_in_status, - "bis - print burn in status on TRAB\n", + "print burn in status on TRAB", "\n" " - prints the status variables of the last burn in test\n" " stored in the onboard EEPROM on TRAB board\n" @@ -851,7 +851,7 @@ int do_temp_log (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) #endif if (argc > 2) { - printf ("Usage:\n%s\n", cmdtp->usage); + cmd_usage(cmdtp); return 1; } @@ -886,7 +886,7 @@ int do_temp_log (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) U_BOOT_CMD( tlog, 2, 1, do_temp_log, - "tlog - log contact temperature [1/100 C] to console (endlessly)\n", + "log contact temperature [1/100 C] to console (endlessly)", "delay\n" " - contact temperature [1/100 C] is printed endlessly to console\n" " <delay> specifies the seconds to wait between two measurements\n" |