diff options
Diffstat (limited to 'board')
| -rw-r--r-- | board/xilinx/zynq/board.c | 158 | ||||
| -rw-r--r-- | board/xilinx/zynqmp/zynqmp-zcu102/psu_init_gpl.c | 23566 | ||||
| -rw-r--r-- | board/xilinx/zynqmp/zynqmp-zcu102/psu_init_gpl.h | 30391 | ||||
| -rw-r--r-- | board/xilinx/zynqmp/zynqmp.c | 167 |
4 files changed, 216 insertions, 54066 deletions
diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c index 4daff8f4f1..2c86940957 100644 --- a/board/xilinx/zynq/board.c +++ b/board/xilinx/zynq/board.c @@ -124,77 +124,125 @@ int zynq_board_read_rom_ethaddr(unsigned char *ethaddr) } #if !defined(CONFIG_SYS_SDRAM_BASE) && !defined(CONFIG_SYS_SDRAM_SIZE) -static const void *get_memory_reg_prop(const void *fdt, int *lenp) +/* + * fdt_get_reg - Fill buffer by information from DT + */ +static phys_size_t fdt_get_reg(const void *fdt, int nodeoffset, void *buf, + const u32 *cell, int n) { - int offset; - - offset = fdt_path_offset(fdt, "/memory"); - if (offset < 0) - return NULL; + int i = 0, b, banks; + int parent_offset = fdt_parent_offset(fdt, nodeoffset); + int address_cells = fdt_address_cells(fdt, parent_offset); + int size_cells = fdt_size_cells(fdt, parent_offset); + char *p = buf; + u64 val; + u64 vals; + + debug("%s: addr_cells=%x, size_cell=%x, buf=%p, cell=%p\n", + __func__, address_cells, size_cells, buf, cell); + + /* Check memory bank setup */ + banks = n % (address_cells + size_cells); + if (banks) + panic("Incorrect memory setup cells=%d, ac=%d, sc=%d\n", + n, address_cells, size_cells); + + banks = n / (address_cells + size_cells); + + for (b = 0; b < banks; b++) { + debug("%s: Bank #%d:\n", __func__, b); + if (address_cells == 2) { + val = cell[i + 1]; + val <<= 32; + val |= cell[i]; + val = fdt64_to_cpu(val); + debug("%s: addr64=%llx, ptr=%p, cell=%p\n", + __func__, val, p, &cell[i]); + *(phys_addr_t *)p = val; + } else { + debug("%s: addr32=%x, ptr=%p\n", + __func__, fdt32_to_cpu(cell[i]), p); + *(phys_addr_t *)p = fdt32_to_cpu(cell[i]); + } + p += sizeof(phys_addr_t); + i += address_cells; + + debug("%s: pa=%p, i=%x, size=%zu\n", __func__, p, i, + sizeof(phys_addr_t)); + + if (size_cells == 2) { + vals = cell[i + 1]; + vals <<= 32; + vals |= cell[i]; + vals = fdt64_to_cpu(vals); + + debug("%s: size64=%llx, ptr=%p, cell=%p\n", + __func__, vals, p, &cell[i]); + *(phys_size_t *)p = vals; + } else { + debug("%s: size32=%x, ptr=%p\n", + __func__, fdt32_to_cpu(cell[i]), p); + *(phys_size_t *)p = fdt32_to_cpu(cell[i]); + } + p += sizeof(phys_size_t); + i += size_cells; + + debug("%s: ps=%p, i=%x, size=%zu\n", + __func__, p, i, sizeof(phys_size_t)); + } - return fdt_getprop(fdt, offset, "reg", lenp); + /* Return the first address size */ + return *(phys_size_t *)((char *)buf + sizeof(phys_addr_t)); } -int dram_init(void) -{ - const void *fdt = gd->fdt_blob; - const fdt32_t *val; - int ac, sc, len; - - ac = fdt_address_cells(fdt, 0); - sc = fdt_size_cells(fdt, 0); - if (ac < 0 || sc < 1 || sc > 2) { - printf("invalid address/size cells\n"); - return -EINVAL; - } +#define FDT_REG_SIZE sizeof(u32) +/* Temp location for sharing data for storing */ +/* Up to 64-bit address + 64-bit size */ +static u8 tmp[CONFIG_NR_DRAM_BANKS * 16]; - val = get_memory_reg_prop(fdt, &len); - if (len / sizeof(*val) < ac + sc) - return -EINVAL; +void dram_init_banksize(void) +{ + int bank; - val += ac; + memcpy(&gd->bd->bi_dram[0], &tmp, sizeof(tmp)); - gd->ram_size = fdtdec_get_number(val, sc); + for (bank = 0; bank < CONFIG_NR_DRAM_BANKS; bank++) { + debug("Bank #%d: start %llx\n", bank, + (unsigned long long)gd->bd->bi_dram[bank].start); + debug("Bank #%d: size %llx\n", bank, + (unsigned long long)gd->bd->bi_dram[bank].size); + } +} - debug("DRAM size = %08lx\n", (unsigned long)gd->ram_size); +int dram_init(void) +{ + int node, len; + const void *blob = gd->fdt_blob; + const u32 *cell; - zynq_ddrc_init(); + memset(&tmp, 0, sizeof(tmp)); - return 0; -} + /* find or create "/memory" node. */ + node = fdt_subnode_offset(blob, 0, "memory"); + if (node < 0) { + printf("%s: Can't get memory node\n", __func__); + return node; + } -void dram_init_banksize(void) -{ - const void *fdt = gd->fdt_blob; - const fdt32_t *val; - int ac, sc, cells, len, i; - - val = get_memory_reg_prop(fdt, &len); - if (len < 0) - return; - - ac = fdt_address_cells(fdt, 0); - sc = fdt_size_cells(fdt, 0); - if (ac < 1 || sc > 2 || sc < 1 || sc > 2) { - printf("invalid address/size cells\n"); - return; + /* Get pointer to cells and lenght of it */ + cell = fdt_getprop(blob, node, "reg", &len); + if (!cell) { + printf("%s: Can't get reg property\n", __func__); + return -1; } - cells = ac + sc; + gd->ram_size = fdt_get_reg(blob, node, &tmp, cell, len / FDT_REG_SIZE); - len /= sizeof(*val); + debug("%s: Initial DRAM size %llx\n", __func__, (u64)gd->ram_size); - for (i = 0; i < CONFIG_NR_DRAM_BANKS && len >= cells; - i++, len -= cells) { - gd->bd->bi_dram[i].start = fdtdec_get_number(val, ac); - val += ac; - gd->bd->bi_dram[i].size = fdtdec_get_number(val, sc); - val += sc; + zynq_ddrc_init(); - debug("DRAM bank %d: start = %08lx, size = %08lx\n", - i, (unsigned long)gd->bd->bi_dram[i].start, - (unsigned long)gd->bd->bi_dram[i].size); - } + return 0; } #else int dram_init(void) diff --git a/board/xilinx/zynqmp/zynqmp-zcu102/psu_init_gpl.c b/board/xilinx/zynqmp/zynqmp-zcu102/psu_init_gpl.c deleted file mode 100644 index 4bc732f69e..0000000000 --- a/board/xilinx/zynqmp/zynqmp-zcu102/psu_init_gpl.c +++ /dev/null @@ -1,23566 +0,0 @@ -/****************************************************************************** -* -* Copyright (C) 2015 Xilinx, Inc. All rights reserved. -* -* This program is free software; you can redistribute it and/or modify -* it under the terms of the GNU General Public License as published by -* the Free Software Foundation; either version 2 of the License, or -* (at your option) any later version. -* -* This program is distributed in the hope that it will be useful, -* but WITHOUT ANY WARRANTY; without even the implied warranty of -* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -* GNU General Public License for more details. -* -* You should have received a copy of the GNU General Public License along -* with this program; if not, see <http://www.gnu.org/licenses/> -* -* -******************************************************************************/ - -#include <xil_io.h> -/* #include <sleep.h> */ -#include "psu_init_gpl.h" - -int mask_pollOnValue(u32 add , u32 mask, u32 value ); - -int mask_poll(u32 add , u32 mask ); - -void mask_delay(u32 delay); - -u32 mask_read(u32 add , u32 mask ); - -static void PSU_Mask_Write (unsigned long offset, unsigned long mask, unsigned long val) -{ - unsigned long RegVal = 0x0; - RegVal = Xil_In32 (offset); - RegVal &= ~(mask); - RegVal |= (val & mask); - Xil_Out32 (offset, RegVal); -} - - void prog_reg (unsigned long addr, unsigned long mask, unsigned long shift, unsigned long value) { - int rdata =0; - rdata = Xil_In32(addr); - rdata = rdata & (~mask); - rdata = rdata | (value << shift); - Xil_Out32(addr,rdata); - } - -unsigned long psu_pll_init_data() { - // : RPLL INIT - /*Register : RPLL_CFG @ 0XFF5E0034</p> - - PLL loop filter resistor control - PSU_CRL_APB_RPLL_CFG_RES 0x2 - - PLL charge pump control - PSU_CRL_APB_RPLL_CFG_CP 0x3 - - PLL loop filter high frequency capacitor control - PSU_CRL_APB_RPLL_CFG_LFHF 0x3 - - Lock circuit counter setting - PSU_CRL_APB_RPLL_CFG_LOCK_CNT 0x258 - - Lock circuit configuration settings for lock windowsize - PSU_CRL_APB_RPLL_CFG_LOCK_DLY 0x3f - - Helper data. Values are to be looked up in a table from Data Sheet - (OFFSET, MASK, VALUE) (0XFF5E0034, 0xFE7FEDEFU ,0x7E4B0C62U) - RegMask = (CRL_APB_RPLL_CFG_RES_MASK | CRL_APB_RPLL_CFG_CP_MASK | CRL_APB_RPLL_CFG_LFHF_MASK | CRL_APB_RPLL_CFG_LOCK_CNT_MASK | CRL_APB_RPLL_CFG_LOCK_DLY_MASK | 0 ); - - RegVal = ((0x00000002U << CRL_APB_RPLL_CFG_RES_SHIFT - | 0x00000003U << CRL_APB_RPLL_CFG_CP_SHIFT - | 0x00000003U << CRL_APB_RPLL_CFG_LFHF_SHIFT - | 0x00000258U << CRL_APB_RPLL_CFG_LOCK_CNT_SHIFT - | 0x0000003FU << CRL_APB_RPLL_CFG_LOCK_DLY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RPLL_CFG_OFFSET ,0xFE7FEDEFU ,0x7E4B0C62U); - /*############################################################################################################################ */ - - // : UPDATE FB_DIV - /*Register : RPLL_CTRL @ 0XFF5E0030</p> - - Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_ - ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source - PSU_CRL_APB_RPLL_CTRL_PRE_SRC 0x0 - - The integer portion of the feedback divider to the PLL - PSU_CRL_APB_RPLL_CTRL_FBDIV 0x48 - - This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency - PSU_CRL_APB_RPLL_CTRL_DIV2 0x1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFF5E0030, 0x00717F00U ,0x00014800U) - RegMask = (CRL_APB_RPLL_CTRL_PRE_SRC_MASK | CRL_APB_RPLL_CTRL_FBDIV_MASK | CRL_APB_RPLL_CTRL_DIV2_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RPLL_CTRL_PRE_SRC_SHIFT - | 0x00000048U << CRL_APB_RPLL_CTRL_FBDIV_SHIFT - | 0x00000001U << CRL_APB_RPLL_CTRL_DIV2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RPLL_CTRL_OFFSET ,0x00717F00U ,0x00014800U); - /*############################################################################################################################ */ - - // : BY PASS PLL - /*Register : RPLL_CTRL @ 0XFF5E0030</p> - - Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_RPLL_CTRL_BYPASS 1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFF5E0030, 0x00000008U ,0x00000008U) - RegMask = (CRL_APB_RPLL_CTRL_BYPASS_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_RPLL_CTRL_BYPASS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RPLL_CTRL_OFFSET ,0x00000008U ,0x00000008U); - /*############################################################################################################################ */ - - // : ASSERT RESET - /*Register : RPLL_CTRL @ 0XFF5E0030</p> - - Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS. - PSU_CRL_APB_RPLL_CTRL_RESET 1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFF5E0030, 0x00000001U ,0x00000001U) - RegMask = (CRL_APB_RPLL_CTRL_RESET_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_RPLL_CTRL_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RPLL_CTRL_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - // : DEASSERT RESET - /*Register : RPLL_CTRL @ 0XFF5E0030</p> - - Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS. - PSU_CRL_APB_RPLL_CTRL_RESET 0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFF5E0030, 0x00000001U ,0x00000000U) - RegMask = (CRL_APB_RPLL_CTRL_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RPLL_CTRL_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RPLL_CTRL_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - // : CHECK PLL STATUS - /*Register : PLL_STATUS @ 0XFF5E0040</p> - - RPLL is locked - PSU_CRL_APB_PLL_STATUS_RPLL_LOCK 1 - (OFFSET, MASK, VALUE) (0XFF5E0040, 0x00000002U ,0x00000002U) */ - mask_poll(CRL_APB_PLL_STATUS_OFFSET,0x00000002U); - - /*############################################################################################################################ */ - - // : REMOVE PLL BY PASS - /*Register : RPLL_CTRL @ 0XFF5E0030</p> - - Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_RPLL_CTRL_BYPASS 0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFF5E0030, 0x00000008U ,0x00000000U) - RegMask = (CRL_APB_RPLL_CTRL_BYPASS_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RPLL_CTRL_BYPASS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RPLL_CTRL_OFFSET ,0x00000008U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : RPLL_TO_FPD_CTRL @ 0XFF5E0048</p> - - Divisor value for this clock. - PSU_CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0 0x3 - - Control for a clock that will be generated in the LPD, but used in the FPD as a clock source for the peripheral clock muxes. - (OFFSET, MASK, VALUE) (0XFF5E0048, 0x00003F00U ,0x00000300U) - RegMask = (CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0_MASK | 0 ); - - RegVal = ((0x00000003U << CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RPLL_TO_FPD_CTRL_OFFSET ,0x00003F00U ,0x00000300U); - /*############################################################################################################################ */ - - // : RPLL FRAC CFG - /*Register : RPLL_FRAC_CFG @ 0XFF5E0038</p> - - Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona - mode and uses DATA of this register for the fractional portion of the feedback divider. - PSU_CRL_APB_RPLL_FRAC_CFG_ENABLED 0x0 - - Fractional value for the Feedback value. - PSU_CRL_APB_RPLL_FRAC_CFG_DATA 0x0 - - Fractional control for the PLL - (OFFSET, MASK, VALUE) (0XFF5E0038, 0x8000FFFFU ,0x00000000U) - RegMask = (CRL_APB_RPLL_FRAC_CFG_ENABLED_MASK | CRL_APB_RPLL_FRAC_CFG_DATA_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RPLL_FRAC_CFG_ENABLED_SHIFT - | 0x00000000U << CRL_APB_RPLL_FRAC_CFG_DATA_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RPLL_FRAC_CFG_OFFSET ,0x8000FFFFU ,0x00000000U); - /*############################################################################################################################ */ - - // : IOPLL INIT - /*Register : IOPLL_CFG @ 0XFF5E0024</p> - - PLL loop filter resistor control - PSU_CRL_APB_IOPLL_CFG_RES 0xc - - PLL charge pump control - PSU_CRL_APB_IOPLL_CFG_CP 0x3 - - PLL loop filter high frequency capacitor control - PSU_CRL_APB_IOPLL_CFG_LFHF 0x3 - - Lock circuit counter setting - PSU_CRL_APB_IOPLL_CFG_LOCK_CNT 0x339 - - Lock circuit configuration settings for lock windowsize - PSU_CRL_APB_IOPLL_CFG_LOCK_DLY 0x3f - - Helper data. Values are to be looked up in a table from Data Sheet - (OFFSET, MASK, VALUE) (0XFF5E0024, 0xFE7FEDEFU ,0x7E672C6CU) - RegMask = (CRL_APB_IOPLL_CFG_RES_MASK | CRL_APB_IOPLL_CFG_CP_MASK | CRL_APB_IOPLL_CFG_LFHF_MASK | CRL_APB_IOPLL_CFG_LOCK_CNT_MASK | CRL_APB_IOPLL_CFG_LOCK_DLY_MASK | 0 ); - - RegVal = ((0x0000000CU << CRL_APB_IOPLL_CFG_RES_SHIFT - | 0x00000003U << CRL_APB_IOPLL_CFG_CP_SHIFT - | 0x00000003U << CRL_APB_IOPLL_CFG_LFHF_SHIFT - | 0x00000339U << CRL_APB_IOPLL_CFG_LOCK_CNT_SHIFT - | 0x0000003FU << CRL_APB_IOPLL_CFG_LOCK_DLY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_IOPLL_CFG_OFFSET ,0xFE7FEDEFU ,0x7E672C6CU); - /*############################################################################################################################ */ - - // : UPDATE FB_DIV - /*Register : IOPLL_CTRL @ 0XFF5E0020</p> - - Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_ - ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source - PSU_CRL_APB_IOPLL_CTRL_PRE_SRC 0x0 - - The integer portion of the feedback divider to the PLL - PSU_CRL_APB_IOPLL_CTRL_FBDIV 0x2d - - This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency - PSU_CRL_APB_IOPLL_CTRL_DIV2 0x0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFF5E0020, 0x00717F00U ,0x00002D00U) - RegMask = (CRL_APB_IOPLL_CTRL_PRE_SRC_MASK | CRL_APB_IOPLL_CTRL_FBDIV_MASK | CRL_APB_IOPLL_CTRL_DIV2_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_IOPLL_CTRL_PRE_SRC_SHIFT - | 0x0000002DU << CRL_APB_IOPLL_CTRL_FBDIV_SHIFT - | 0x00000000U << CRL_APB_IOPLL_CTRL_DIV2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_IOPLL_CTRL_OFFSET ,0x00717F00U ,0x00002D00U); - /*############################################################################################################################ */ - - // : BY PASS PLL - /*Register : IOPLL_CTRL @ 0XFF5E0020</p> - - Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_IOPLL_CTRL_BYPASS 1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFF5E0020, 0x00000008U ,0x00000008U) - RegMask = (CRL_APB_IOPLL_CTRL_BYPASS_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_IOPLL_CTRL_BYPASS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_IOPLL_CTRL_OFFSET ,0x00000008U ,0x00000008U); - /*############################################################################################################################ */ - - // : ASSERT RESET - /*Register : IOPLL_CTRL @ 0XFF5E0020</p> - - Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS. - PSU_CRL_APB_IOPLL_CTRL_RESET 1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFF5E0020, 0x00000001U ,0x00000001U) - RegMask = (CRL_APB_IOPLL_CTRL_RESET_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_IOPLL_CTRL_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_IOPLL_CTRL_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - // : DEASSERT RESET - /*Register : IOPLL_CTRL @ 0XFF5E0020</p> - - Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS. - PSU_CRL_APB_IOPLL_CTRL_RESET 0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFF5E0020, 0x00000001U ,0x00000000U) - RegMask = (CRL_APB_IOPLL_CTRL_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_IOPLL_CTRL_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_IOPLL_CTRL_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - // : CHECK PLL STATUS - /*Register : PLL_STATUS @ 0XFF5E0040</p> - - IOPLL is locked - PSU_CRL_APB_PLL_STATUS_IOPLL_LOCK 1 - (OFFSET, MASK, VALUE) (0XFF5E0040, 0x00000001U ,0x00000001U) */ - mask_poll(CRL_APB_PLL_STATUS_OFFSET,0x00000001U); - - /*############################################################################################################################ */ - - // : REMOVE PLL BY PASS - /*Register : IOPLL_CTRL @ 0XFF5E0020</p> - - Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_IOPLL_CTRL_BYPASS 0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFF5E0020, 0x00000008U ,0x00000000U) - RegMask = (CRL_APB_IOPLL_CTRL_BYPASS_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_IOPLL_CTRL_BYPASS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_IOPLL_CTRL_OFFSET ,0x00000008U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : IOPLL_TO_FPD_CTRL @ 0XFF5E0044</p> - - Divisor value for this clock. - PSU_CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0 0x3 - - Control for a clock that will be generated in the LPD, but used in the FPD as a clock source for the peripheral clock muxes. - (OFFSET, MASK, VALUE) (0XFF5E0044, 0x00003F00U ,0x00000300U) - RegMask = (CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0_MASK | 0 ); - - RegVal = ((0x00000003U << CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_IOPLL_TO_FPD_CTRL_OFFSET ,0x00003F00U ,0x00000300U); - /*############################################################################################################################ */ - - // : IOPLL FRAC CFG - /*Register : IOPLL_FRAC_CFG @ 0XFF5E0028</p> - - Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona - mode and uses DATA of this register for the fractional portion of the feedback divider. - PSU_CRL_APB_IOPLL_FRAC_CFG_ENABLED 0x0 - - Fractional value for the Feedback value. - PSU_CRL_APB_IOPLL_FRAC_CFG_DATA 0x0 - - Fractional control for the PLL - (OFFSET, MASK, VALUE) (0XFF5E0028, 0x8000FFFFU ,0x00000000U) - RegMask = (CRL_APB_IOPLL_FRAC_CFG_ENABLED_MASK | CRL_APB_IOPLL_FRAC_CFG_DATA_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_IOPLL_FRAC_CFG_ENABLED_SHIFT - | 0x00000000U << CRL_APB_IOPLL_FRAC_CFG_DATA_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_IOPLL_FRAC_CFG_OFFSET ,0x8000FFFFU ,0x00000000U); - /*############################################################################################################################ */ - - // : APU_PLL INIT - /*Register : APLL_CFG @ 0XFD1A0024</p> - - PLL loop filter resistor control - PSU_CRF_APB_APLL_CFG_RES 0x2 - - PLL charge pump control - PSU_CRF_APB_APLL_CFG_CP 0x3 - - PLL loop filter high frequency capacitor control - PSU_CRF_APB_APLL_CFG_LFHF 0x3 - - Lock circuit counter setting - PSU_CRF_APB_APLL_CFG_LOCK_CNT 0x258 - - Lock circuit configuration settings for lock windowsize - PSU_CRF_APB_APLL_CFG_LOCK_DLY 0x3f - - Helper data. Values are to be looked up in a table from Data Sheet - (OFFSET, MASK, VALUE) (0XFD1A0024, 0xFE7FEDEFU ,0x7E4B0C62U) - RegMask = (CRF_APB_APLL_CFG_RES_MASK | CRF_APB_APLL_CFG_CP_MASK | CRF_APB_APLL_CFG_LFHF_MASK | CRF_APB_APLL_CFG_LOCK_CNT_MASK | CRF_APB_APLL_CFG_LOCK_DLY_MASK | 0 ); - - RegVal = ((0x00000002U << CRF_APB_APLL_CFG_RES_SHIFT - | 0x00000003U << CRF_APB_APLL_CFG_CP_SHIFT - | 0x00000003U << CRF_APB_APLL_CFG_LFHF_SHIFT - | 0x00000258U << CRF_APB_APLL_CFG_LOCK_CNT_SHIFT - | 0x0000003FU << CRF_APB_APLL_CFG_LOCK_DLY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_APLL_CFG_OFFSET ,0xFE7FEDEFU ,0x7E4B0C62U); - /*############################################################################################################################ */ - - // : UPDATE FB_DIV - /*Register : APLL_CTRL @ 0XFD1A0020</p> - - Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_ - ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source - PSU_CRF_APB_APLL_CTRL_PRE_SRC 0x0 - - The integer portion of the feedback divider to the PLL - PSU_CRF_APB_APLL_CTRL_FBDIV 0x48 - - This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency - PSU_CRF_APB_APLL_CTRL_DIV2 0x1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A0020, 0x00717F00U ,0x00014800U) - RegMask = (CRF_APB_APLL_CTRL_PRE_SRC_MASK | CRF_APB_APLL_CTRL_FBDIV_MASK | CRF_APB_APLL_CTRL_DIV2_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_APLL_CTRL_PRE_SRC_SHIFT - | 0x00000048U << CRF_APB_APLL_CTRL_FBDIV_SHIFT - | 0x00000001U << CRF_APB_APLL_CTRL_DIV2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_APLL_CTRL_OFFSET ,0x00717F00U ,0x00014800U); - /*############################################################################################################################ */ - - // : BY PASS PLL - /*Register : APLL_CTRL @ 0XFD1A0020</p> - - Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_APLL_CTRL_BYPASS 1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A0020, 0x00000008U ,0x00000008U) - RegMask = (CRF_APB_APLL_CTRL_BYPASS_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_APLL_CTRL_BYPASS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_APLL_CTRL_OFFSET ,0x00000008U ,0x00000008U); - /*############################################################################################################################ */ - - // : ASSERT RESET - /*Register : APLL_CTRL @ 0XFD1A0020</p> - - Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS. - PSU_CRF_APB_APLL_CTRL_RESET 1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A0020, 0x00000001U ,0x00000001U) - RegMask = (CRF_APB_APLL_CTRL_RESET_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_APLL_CTRL_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_APLL_CTRL_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - // : DEASSERT RESET - /*Register : APLL_CTRL @ 0XFD1A0020</p> - - Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS. - PSU_CRF_APB_APLL_CTRL_RESET 0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A0020, 0x00000001U ,0x00000000U) - RegMask = (CRF_APB_APLL_CTRL_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_APLL_CTRL_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_APLL_CTRL_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - // : CHECK PLL STATUS - /*Register : PLL_STATUS @ 0XFD1A0044</p> - - APLL is locked - PSU_CRF_APB_PLL_STATUS_APLL_LOCK 1 - (OFFSET, MASK, VALUE) (0XFD1A0044, 0x00000001U ,0x00000001U) */ - mask_poll(CRF_APB_PLL_STATUS_OFFSET,0x00000001U); - - /*############################################################################################################################ */ - - // : REMOVE PLL BY PASS - /*Register : APLL_CTRL @ 0XFD1A0020</p> - - Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_APLL_CTRL_BYPASS 0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A0020, 0x00000008U ,0x00000000U) - RegMask = (CRF_APB_APLL_CTRL_BYPASS_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_APLL_CTRL_BYPASS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_APLL_CTRL_OFFSET ,0x00000008U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : APLL_TO_LPD_CTRL @ 0XFD1A0048</p> - - Divisor value for this clock. - PSU_CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0 0x3 - - Control for a clock that will be generated in the FPD, but used in the LPD as a clock source for the peripheral clock muxes. - (OFFSET, MASK, VALUE) (0XFD1A0048, 0x00003F00U ,0x00000300U) - RegMask = (CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0_MASK | 0 ); - - RegVal = ((0x00000003U << CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_APLL_TO_LPD_CTRL_OFFSET ,0x00003F00U ,0x00000300U); - /*############################################################################################################################ */ - - // : APLL FRAC CFG - /*Register : APLL_FRAC_CFG @ 0XFD1A0028</p> - - Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona - mode and uses DATA of this register for the fractional portion of the feedback divider. - PSU_CRF_APB_APLL_FRAC_CFG_ENABLED 0x0 - - Fractional value for the Feedback value. - PSU_CRF_APB_APLL_FRAC_CFG_DATA 0x0 - - Fractional control for the PLL - (OFFSET, MASK, VALUE) (0XFD1A0028, 0x8000FFFFU ,0x00000000U) - RegMask = (CRF_APB_APLL_FRAC_CFG_ENABLED_MASK | CRF_APB_APLL_FRAC_CFG_DATA_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_APLL_FRAC_CFG_ENABLED_SHIFT - | 0x00000000U << CRF_APB_APLL_FRAC_CFG_DATA_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_APLL_FRAC_CFG_OFFSET ,0x8000FFFFU ,0x00000000U); - /*############################################################################################################################ */ - - // : DDR_PLL INIT - /*Register : DPLL_CFG @ 0XFD1A0030</p> - - PLL loop filter resistor control - PSU_CRF_APB_DPLL_CFG_RES 0x2 - - PLL charge pump control - PSU_CRF_APB_DPLL_CFG_CP 0x3 - - PLL loop filter high frequency capacitor control - PSU_CRF_APB_DPLL_CFG_LFHF 0x3 - - Lock circuit counter setting - PSU_CRF_APB_DPLL_CFG_LOCK_CNT 0x258 - - Lock circuit configuration settings for lock windowsize - PSU_CRF_APB_DPLL_CFG_LOCK_DLY 0x3f - - Helper data. Values are to be looked up in a table from Data Sheet - (OFFSET, MASK, VALUE) (0XFD1A0030, 0xFE7FEDEFU ,0x7E4B0C62U) - RegMask = (CRF_APB_DPLL_CFG_RES_MASK | CRF_APB_DPLL_CFG_CP_MASK | CRF_APB_DPLL_CFG_LFHF_MASK | CRF_APB_DPLL_CFG_LOCK_CNT_MASK | CRF_APB_DPLL_CFG_LOCK_DLY_MASK | 0 ); - - RegVal = ((0x00000002U << CRF_APB_DPLL_CFG_RES_SHIFT - | 0x00000003U << CRF_APB_DPLL_CFG_CP_SHIFT - | 0x00000003U << CRF_APB_DPLL_CFG_LFHF_SHIFT - | 0x00000258U << CRF_APB_DPLL_CFG_LOCK_CNT_SHIFT - | 0x0000003FU << CRF_APB_DPLL_CFG_LOCK_DLY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DPLL_CFG_OFFSET ,0xFE7FEDEFU ,0x7E4B0C62U); - /*############################################################################################################################ */ - - // : UPDATE FB_DIV - /*Register : DPLL_CTRL @ 0XFD1A002C</p> - - Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_ - ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source - PSU_CRF_APB_DPLL_CTRL_PRE_SRC 0x0 - - The integer portion of the feedback divider to the PLL - PSU_CRF_APB_DPLL_CTRL_FBDIV 0x40 - - This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency - PSU_CRF_APB_DPLL_CTRL_DIV2 0x1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A002C, 0x00717F00U ,0x00014000U) - RegMask = (CRF_APB_DPLL_CTRL_PRE_SRC_MASK | CRF_APB_DPLL_CTRL_FBDIV_MASK | CRF_APB_DPLL_CTRL_DIV2_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_DPLL_CTRL_PRE_SRC_SHIFT - | 0x00000040U << CRF_APB_DPLL_CTRL_FBDIV_SHIFT - | 0x00000001U << CRF_APB_DPLL_CTRL_DIV2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DPLL_CTRL_OFFSET ,0x00717F00U ,0x00014000U); - /*############################################################################################################################ */ - - // : BY PASS PLL - /*Register : DPLL_CTRL @ 0XFD1A002C</p> - - Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_DPLL_CTRL_BYPASS 1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A002C, 0x00000008U ,0x00000008U) - RegMask = (CRF_APB_DPLL_CTRL_BYPASS_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_DPLL_CTRL_BYPASS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DPLL_CTRL_OFFSET ,0x00000008U ,0x00000008U); - /*############################################################################################################################ */ - - // : ASSERT RESET - /*Register : DPLL_CTRL @ 0XFD1A002C</p> - - Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS. - PSU_CRF_APB_DPLL_CTRL_RESET 1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A002C, 0x00000001U ,0x00000001U) - RegMask = (CRF_APB_DPLL_CTRL_RESET_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_DPLL_CTRL_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DPLL_CTRL_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - // : DEASSERT RESET - /*Register : DPLL_CTRL @ 0XFD1A002C</p> - - Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS. - PSU_CRF_APB_DPLL_CTRL_RESET 0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A002C, 0x00000001U ,0x00000000U) - RegMask = (CRF_APB_DPLL_CTRL_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_DPLL_CTRL_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DPLL_CTRL_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - // : CHECK PLL STATUS - /*Register : PLL_STATUS @ 0XFD1A0044</p> - - DPLL is locked - PSU_CRF_APB_PLL_STATUS_DPLL_LOCK 1 - (OFFSET, MASK, VALUE) (0XFD1A0044, 0x00000002U ,0x00000002U) */ - mask_poll(CRF_APB_PLL_STATUS_OFFSET,0x00000002U); - - /*############################################################################################################################ */ - - // : REMOVE PLL BY PASS - /*Register : DPLL_CTRL @ 0XFD1A002C</p> - - Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_DPLL_CTRL_BYPASS 0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A002C, 0x00000008U ,0x00000000U) - RegMask = (CRF_APB_DPLL_CTRL_BYPASS_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_DPLL_CTRL_BYPASS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DPLL_CTRL_OFFSET ,0x00000008U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DPLL_TO_LPD_CTRL @ 0XFD1A004C</p> - - Divisor value for this clock. - PSU_CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0 0x3 - - Control for a clock that will be generated in the FPD, but used in the LPD as a clock source for the peripheral clock muxes. - (OFFSET, MASK, VALUE) (0XFD1A004C, 0x00003F00U ,0x00000300U) - RegMask = (CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0_MASK | 0 ); - - RegVal = ((0x00000003U << CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DPLL_TO_LPD_CTRL_OFFSET ,0x00003F00U ,0x00000300U); - /*############################################################################################################################ */ - - // : DPLL FRAC CFG - /*Register : DPLL_FRAC_CFG @ 0XFD1A0034</p> - - Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona - mode and uses DATA of this register for the fractional portion of the feedback divider. - PSU_CRF_APB_DPLL_FRAC_CFG_ENABLED 0x0 - - Fractional value for the Feedback value. - PSU_CRF_APB_DPLL_FRAC_CFG_DATA 0x0 - - Fractional control for the PLL - (OFFSET, MASK, VALUE) (0XFD1A0034, 0x8000FFFFU ,0x00000000U) - RegMask = (CRF_APB_DPLL_FRAC_CFG_ENABLED_MASK | CRF_APB_DPLL_FRAC_CFG_DATA_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_DPLL_FRAC_CFG_ENABLED_SHIFT - | 0x00000000U << CRF_APB_DPLL_FRAC_CFG_DATA_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DPLL_FRAC_CFG_OFFSET ,0x8000FFFFU ,0x00000000U); - /*############################################################################################################################ */ - - // : VIDEO_PLL INIT - /*Register : VPLL_CFG @ 0XFD1A003C</p> - - PLL loop filter resistor control - PSU_CRF_APB_VPLL_CFG_RES 0x2 - - PLL charge pump control - PSU_CRF_APB_VPLL_CFG_CP 0x3 - - PLL loop filter high frequency capacitor control - PSU_CRF_APB_VPLL_CFG_LFHF 0x3 - - Lock circuit counter setting - PSU_CRF_APB_VPLL_CFG_LOCK_CNT 0x28a - - Lock circuit configuration settings for lock windowsize - PSU_CRF_APB_VPLL_CFG_LOCK_DLY 0x3f - - Helper data. Values are to be looked up in a table from Data Sheet - (OFFSET, MASK, VALUE) (0XFD1A003C, 0xFE7FEDEFU ,0x7E514C62U) - RegMask = (CRF_APB_VPLL_CFG_RES_MASK | CRF_APB_VPLL_CFG_CP_MASK | CRF_APB_VPLL_CFG_LFHF_MASK | CRF_APB_VPLL_CFG_LOCK_CNT_MASK | CRF_APB_VPLL_CFG_LOCK_DLY_MASK | 0 ); - - RegVal = ((0x00000002U << CRF_APB_VPLL_CFG_RES_SHIFT - | 0x00000003U << CRF_APB_VPLL_CFG_CP_SHIFT - | 0x00000003U << CRF_APB_VPLL_CFG_LFHF_SHIFT - | 0x0000028AU << CRF_APB_VPLL_CFG_LOCK_CNT_SHIFT - | 0x0000003FU << CRF_APB_VPLL_CFG_LOCK_DLY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_VPLL_CFG_OFFSET ,0xFE7FEDEFU ,0x7E514C62U); - /*############################################################################################################################ */ - - // : UPDATE FB_DIV - /*Register : VPLL_CTRL @ 0XFD1A0038</p> - - Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_ - ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source - PSU_CRF_APB_VPLL_CTRL_PRE_SRC 0x0 - - The integer portion of the feedback divider to the PLL - PSU_CRF_APB_VPLL_CTRL_FBDIV 0x39 - - This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency - PSU_CRF_APB_VPLL_CTRL_DIV2 0x1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A0038, 0x00717F00U ,0x00013900U) - RegMask = (CRF_APB_VPLL_CTRL_PRE_SRC_MASK | CRF_APB_VPLL_CTRL_FBDIV_MASK | CRF_APB_VPLL_CTRL_DIV2_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_VPLL_CTRL_PRE_SRC_SHIFT - | 0x00000039U << CRF_APB_VPLL_CTRL_FBDIV_SHIFT - | 0x00000001U << CRF_APB_VPLL_CTRL_DIV2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_VPLL_CTRL_OFFSET ,0x00717F00U ,0x00013900U); - /*############################################################################################################################ */ - - // : BY PASS PLL - /*Register : VPLL_CTRL @ 0XFD1A0038</p> - - Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_VPLL_CTRL_BYPASS 1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A0038, 0x00000008U ,0x00000008U) - RegMask = (CRF_APB_VPLL_CTRL_BYPASS_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_VPLL_CTRL_BYPASS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_VPLL_CTRL_OFFSET ,0x00000008U ,0x00000008U); - /*############################################################################################################################ */ - - // : ASSERT RESET - /*Register : VPLL_CTRL @ 0XFD1A0038</p> - - Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS. - PSU_CRF_APB_VPLL_CTRL_RESET 1 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A0038, 0x00000001U ,0x00000001U) - RegMask = (CRF_APB_VPLL_CTRL_RESET_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_VPLL_CTRL_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_VPLL_CTRL_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - // : DEASSERT RESET - /*Register : VPLL_CTRL @ 0XFD1A0038</p> - - Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS. - PSU_CRF_APB_VPLL_CTRL_RESET 0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A0038, 0x00000001U ,0x00000000U) - RegMask = (CRF_APB_VPLL_CTRL_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_VPLL_CTRL_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_VPLL_CTRL_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - // : CHECK PLL STATUS - /*Register : PLL_STATUS @ 0XFD1A0044</p> - - VPLL is locked - PSU_CRF_APB_PLL_STATUS_VPLL_LOCK 1 - (OFFSET, MASK, VALUE) (0XFD1A0044, 0x00000004U ,0x00000004U) */ - mask_poll(CRF_APB_PLL_STATUS_OFFSET,0x00000004U); - - /*############################################################################################################################ */ - - // : REMOVE PLL BY PASS - /*Register : VPLL_CTRL @ 0XFD1A0038</p> - - Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_VPLL_CTRL_BYPASS 0 - - PLL Basic Control - (OFFSET, MASK, VALUE) (0XFD1A0038, 0x00000008U ,0x00000000U) - RegMask = (CRF_APB_VPLL_CTRL_BYPASS_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_VPLL_CTRL_BYPASS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_VPLL_CTRL_OFFSET ,0x00000008U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : VPLL_TO_LPD_CTRL @ 0XFD1A0050</p> - - Divisor value for this clock. - PSU_CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0 0x3 - - Control for a clock that will be generated in the FPD, but used in the LPD as a clock source for the peripheral clock muxes. - (OFFSET, MASK, VALUE) (0XFD1A0050, 0x00003F00U ,0x00000300U) - RegMask = (CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0_MASK | 0 ); - - RegVal = ((0x00000003U << CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_VPLL_TO_LPD_CTRL_OFFSET ,0x00003F00U ,0x00000300U); - /*############################################################################################################################ */ - - // : VIDEO FRAC CFG - /*Register : VPLL_FRAC_CFG @ 0XFD1A0040</p> - - Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona - mode and uses DATA of this register for the fractional portion of the feedback divider. - PSU_CRF_APB_VPLL_FRAC_CFG_ENABLED 0x1 - - Fractional value for the Feedback value. - PSU_CRF_APB_VPLL_FRAC_CFG_DATA 0x820c - - Fractional control for the PLL - (OFFSET, MASK, VALUE) (0XFD1A0040, 0x8000FFFFU ,0x8000820CU) - RegMask = (CRF_APB_VPLL_FRAC_CFG_ENABLED_MASK | CRF_APB_VPLL_FRAC_CFG_DATA_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_VPLL_FRAC_CFG_ENABLED_SHIFT - | 0x0000820CU << CRF_APB_VPLL_FRAC_CFG_DATA_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_VPLL_FRAC_CFG_OFFSET ,0x8000FFFFU ,0x8000820CU); - /*############################################################################################################################ */ - - - return 1; -} -unsigned long psu_clock_init_data() { - // : CLOCK CONTROL SLCR REGISTER - /*Register : GEM3_REF_CTRL @ 0XFF5E005C</p> - - Clock active for the RX channel - PSU_CRL_APB_GEM3_REF_CTRL_RX_CLKACT 0x1 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_GEM3_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_GEM3_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_GEM3_REF_CTRL_DIVISOR0 0xc - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_GEM3_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E005C, 0x063F3F07U ,0x06010C00U) - RegMask = (CRL_APB_GEM3_REF_CTRL_RX_CLKACT_MASK | CRL_APB_GEM3_REF_CTRL_CLKACT_MASK | CRL_APB_GEM3_REF_CTRL_DIVISOR1_MASK | CRL_APB_GEM3_REF_CTRL_DIVISOR0_MASK | CRL_APB_GEM3_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_GEM3_REF_CTRL_RX_CLKACT_SHIFT - | 0x00000001U << CRL_APB_GEM3_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_GEM3_REF_CTRL_DIVISOR1_SHIFT - | 0x0000000CU << CRL_APB_GEM3_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_GEM3_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_GEM3_REF_CTRL_OFFSET ,0x063F3F07U ,0x06010C00U); - /*############################################################################################################################ */ - - /*Register : USB0_BUS_REF_CTRL @ 0XFF5E0060</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_USB0_BUS_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0 0x6 - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_USB0_BUS_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0060, 0x023F3F07U ,0x02010600U) - RegMask = (CRL_APB_USB0_BUS_REF_CTRL_CLKACT_MASK | CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1_MASK | CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0_MASK | CRL_APB_USB0_BUS_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_USB0_BUS_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1_SHIFT - | 0x00000006U << CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_USB0_BUS_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_USB0_BUS_REF_CTRL_OFFSET ,0x023F3F07U ,0x02010600U); - /*############################################################################################################################ */ - - /*Register : USB3_DUAL_REF_CTRL @ 0XFF5E004C</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_USB3_DUAL_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1 0xf - - 6 bit divider - PSU_CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0 0x5 - - 000 = IOPLL; 010 = RPLL; 011 = DPLL. (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E004C, 0x023F3F07U ,0x020F0500U) - RegMask = (CRL_APB_USB3_DUAL_REF_CTRL_CLKACT_MASK | CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1_MASK | CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0_MASK | CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_USB3_DUAL_REF_CTRL_CLKACT_SHIFT - | 0x0000000FU << CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1_SHIFT - | 0x00000005U << CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_USB3_DUAL_REF_CTRL_OFFSET ,0x023F3F07U ,0x020F0500U); - /*############################################################################################################################ */ - - /*Register : QSPI_REF_CTRL @ 0XFF5E0068</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_QSPI_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_QSPI_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_QSPI_REF_CTRL_DIVISOR0 0xc - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_QSPI_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0068, 0x013F3F07U ,0x01010C00U) - RegMask = (CRL_APB_QSPI_REF_CTRL_CLKACT_MASK | CRL_APB_QSPI_REF_CTRL_DIVISOR1_MASK | CRL_APB_QSPI_REF_CTRL_DIVISOR0_MASK | CRL_APB_QSPI_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_QSPI_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_QSPI_REF_CTRL_DIVISOR1_SHIFT - | 0x0000000CU << CRL_APB_QSPI_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_QSPI_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_QSPI_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010C00U); - /*############################################################################################################################ */ - - /*Register : SDIO1_REF_CTRL @ 0XFF5E0070</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_SDIO1_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_SDIO1_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_SDIO1_REF_CTRL_DIVISOR0 0x6 - - 000 = IOPLL; 010 = RPLL; 011 = VPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_SDIO1_REF_CTRL_SRCSEL 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0070, 0x013F3F07U ,0x01010602U) - RegMask = (CRL_APB_SDIO1_REF_CTRL_CLKACT_MASK | CRL_APB_SDIO1_REF_CTRL_DIVISOR1_MASK | CRL_APB_SDIO1_REF_CTRL_DIVISOR0_MASK | CRL_APB_SDIO1_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_SDIO1_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_SDIO1_REF_CTRL_DIVISOR1_SHIFT - | 0x00000006U << CRL_APB_SDIO1_REF_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_SDIO1_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_SDIO1_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010602U); - /*############################################################################################################################ */ - - /*Register : SDIO_CLK_CTRL @ 0XFF18030C</p> - - MIO pad selection for sdio1_rx_clk (feedback clock from the PAD) 0: MIO [51] 1: MIO [76] - PSU_IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL 0 - - SoC Debug Clock Control - (OFFSET, MASK, VALUE) (0XFF18030C, 0x00020000U ,0x00000000U) - RegMask = (IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_SDIO_CLK_CTRL_OFFSET ,0x00020000U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : UART0_REF_CTRL @ 0XFF5E0074</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_UART0_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_UART0_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_UART0_REF_CTRL_DIVISOR0 0xf - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_UART0_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0074, 0x013F3F07U ,0x01010F00U) - RegMask = (CRL_APB_UART0_REF_CTRL_CLKACT_MASK | CRL_APB_UART0_REF_CTRL_DIVISOR1_MASK | CRL_APB_UART0_REF_CTRL_DIVISOR0_MASK | CRL_APB_UART0_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_UART0_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_UART0_REF_CTRL_DIVISOR1_SHIFT - | 0x0000000FU << CRL_APB_UART0_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_UART0_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_UART0_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010F00U); - /*############################################################################################################################ */ - - /*Register : UART1_REF_CTRL @ 0XFF5E0078</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_UART1_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_UART1_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_UART1_REF_CTRL_DIVISOR0 0xf - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_UART1_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0078, 0x013F3F07U ,0x01010F00U) - RegMask = (CRL_APB_UART1_REF_CTRL_CLKACT_MASK | CRL_APB_UART1_REF_CTRL_DIVISOR1_MASK | CRL_APB_UART1_REF_CTRL_DIVISOR0_MASK | CRL_APB_UART1_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_UART1_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_UART1_REF_CTRL_DIVISOR1_SHIFT - | 0x0000000FU << CRL_APB_UART1_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_UART1_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_UART1_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010F00U); - /*############################################################################################################################ */ - - /*Register : I2C0_REF_CTRL @ 0XFF5E0120</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_I2C0_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_I2C0_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_I2C0_REF_CTRL_DIVISOR0 0xf - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_I2C0_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0120, 0x013F3F07U ,0x01010F00U) - RegMask = (CRL_APB_I2C0_REF_CTRL_CLKACT_MASK | CRL_APB_I2C0_REF_CTRL_DIVISOR1_MASK | CRL_APB_I2C0_REF_CTRL_DIVISOR0_MASK | CRL_APB_I2C0_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_I2C0_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_I2C0_REF_CTRL_DIVISOR1_SHIFT - | 0x0000000FU << CRL_APB_I2C0_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_I2C0_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_I2C0_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010F00U); - /*############################################################################################################################ */ - - /*Register : I2C1_REF_CTRL @ 0XFF5E0124</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_I2C1_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_I2C1_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_I2C1_REF_CTRL_DIVISOR0 0xf - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_I2C1_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0124, 0x013F3F07U ,0x01010F00U) - RegMask = (CRL_APB_I2C1_REF_CTRL_CLKACT_MASK | CRL_APB_I2C1_REF_CTRL_DIVISOR1_MASK | CRL_APB_I2C1_REF_CTRL_DIVISOR0_MASK | CRL_APB_I2C1_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_I2C1_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_I2C1_REF_CTRL_DIVISOR1_SHIFT - | 0x0000000FU << CRL_APB_I2C1_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_I2C1_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_I2C1_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010F00U); - /*############################################################################################################################ */ - - /*Register : CAN1_REF_CTRL @ 0XFF5E0088</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_CAN1_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_CAN1_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_CAN1_REF_CTRL_DIVISOR0 0xf - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_CAN1_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0088, 0x013F3F07U ,0x01010F00U) - RegMask = (CRL_APB_CAN1_REF_CTRL_CLKACT_MASK | CRL_APB_CAN1_REF_CTRL_DIVISOR1_MASK | CRL_APB_CAN1_REF_CTRL_DIVISOR0_MASK | CRL_APB_CAN1_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_CAN1_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_CAN1_REF_CTRL_DIVISOR1_SHIFT - | 0x0000000FU << CRL_APB_CAN1_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_CAN1_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_CAN1_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010F00U); - /*############################################################################################################################ */ - - /*Register : CPU_R5_CTRL @ 0XFF5E0090</p> - - Turing this off will shut down the OCM, some parts of the APM, and prevent transactions going from the FPD to the LPD and cou - d lead to system hang - PSU_CRL_APB_CPU_R5_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_CPU_R5_CTRL_DIVISOR0 0x3 - - 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_CPU_R5_CTRL_SRCSEL 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0090, 0x01003F07U ,0x01000302U) - RegMask = (CRL_APB_CPU_R5_CTRL_CLKACT_MASK | CRL_APB_CPU_R5_CTRL_DIVISOR0_MASK | CRL_APB_CPU_R5_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_CPU_R5_CTRL_CLKACT_SHIFT - | 0x00000003U << CRL_APB_CPU_R5_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_CPU_R5_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_CPU_R5_CTRL_OFFSET ,0x01003F07U ,0x01000302U); - /*############################################################################################################################ */ - - /*Register : IOU_SWITCH_CTRL @ 0XFF5E009C</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_IOU_SWITCH_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_IOU_SWITCH_CTRL_DIVISOR0 0x6 - - 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_IOU_SWITCH_CTRL_SRCSEL 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E009C, 0x01003F07U ,0x01000602U) - RegMask = (CRL_APB_IOU_SWITCH_CTRL_CLKACT_MASK | CRL_APB_IOU_SWITCH_CTRL_DIVISOR0_MASK | CRL_APB_IOU_SWITCH_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_IOU_SWITCH_CTRL_CLKACT_SHIFT - | 0x00000006U << CRL_APB_IOU_SWITCH_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_IOU_SWITCH_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_IOU_SWITCH_CTRL_OFFSET ,0x01003F07U ,0x01000602U); - /*############################################################################################################################ */ - - /*Register : PCAP_CTRL @ 0XFF5E00A4</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_PCAP_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_PCAP_CTRL_DIVISOR0 0x6 - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_PCAP_CTRL_SRCSEL 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E00A4, 0x01003F07U ,0x01000602U) - RegMask = (CRL_APB_PCAP_CTRL_CLKACT_MASK | CRL_APB_PCAP_CTRL_DIVISOR0_MASK | CRL_APB_PCAP_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_PCAP_CTRL_CLKACT_SHIFT - | 0x00000006U << CRL_APB_PCAP_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_PCAP_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_PCAP_CTRL_OFFSET ,0x01003F07U ,0x01000602U); - /*############################################################################################################################ */ - - /*Register : LPD_SWITCH_CTRL @ 0XFF5E00A8</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_LPD_SWITCH_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_LPD_SWITCH_CTRL_DIVISOR0 0x3 - - 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_LPD_SWITCH_CTRL_SRCSEL 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E00A8, 0x01003F07U ,0x01000302U) - RegMask = (CRL_APB_LPD_SWITCH_CTRL_CLKACT_MASK | CRL_APB_LPD_SWITCH_CTRL_DIVISOR0_MASK | CRL_APB_LPD_SWITCH_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_LPD_SWITCH_CTRL_CLKACT_SHIFT - | 0x00000003U << CRL_APB_LPD_SWITCH_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_LPD_SWITCH_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_LPD_SWITCH_CTRL_OFFSET ,0x01003F07U ,0x01000302U); - /*############################################################################################################################ */ - - /*Register : LPD_LSBUS_CTRL @ 0XFF5E00AC</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_LPD_LSBUS_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_LPD_LSBUS_CTRL_DIVISOR0 0xf - - 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_LPD_LSBUS_CTRL_SRCSEL 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E00AC, 0x01003F07U ,0x01000F02U) - RegMask = (CRL_APB_LPD_LSBUS_CTRL_CLKACT_MASK | CRL_APB_LPD_LSBUS_CTRL_DIVISOR0_MASK | CRL_APB_LPD_LSBUS_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_LPD_LSBUS_CTRL_CLKACT_SHIFT - | 0x0000000FU << CRL_APB_LPD_LSBUS_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_LPD_LSBUS_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_LPD_LSBUS_CTRL_OFFSET ,0x01003F07U ,0x01000F02U); - /*############################################################################################################################ */ - - /*Register : DBG_LPD_CTRL @ 0XFF5E00B0</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_DBG_LPD_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_DBG_LPD_CTRL_DIVISOR0 0x6 - - 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_DBG_LPD_CTRL_SRCSEL 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E00B0, 0x01003F07U ,0x01000602U) - RegMask = (CRL_APB_DBG_LPD_CTRL_CLKACT_MASK | CRL_APB_DBG_LPD_CTRL_DIVISOR0_MASK | CRL_APB_DBG_LPD_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_DBG_LPD_CTRL_CLKACT_SHIFT - | 0x00000006U << CRL_APB_DBG_LPD_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_DBG_LPD_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_DBG_LPD_CTRL_OFFSET ,0x01003F07U ,0x01000602U); - /*############################################################################################################################ */ - - /*Register : ADMA_REF_CTRL @ 0XFF5E00B8</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_ADMA_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_ADMA_REF_CTRL_DIVISOR0 0x3 - - 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_ADMA_REF_CTRL_SRCSEL 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E00B8, 0x01003F07U ,0x01000302U) - RegMask = (CRL_APB_ADMA_REF_CTRL_CLKACT_MASK | CRL_APB_ADMA_REF_CTRL_DIVISOR0_MASK | CRL_APB_ADMA_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_ADMA_REF_CTRL_CLKACT_SHIFT - | 0x00000003U << CRL_APB_ADMA_REF_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_ADMA_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_ADMA_REF_CTRL_OFFSET ,0x01003F07U ,0x01000302U); - /*############################################################################################################################ */ - - /*Register : PL0_REF_CTRL @ 0XFF5E00C0</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_PL0_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_PL0_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_PL0_REF_CTRL_DIVISOR0 0xf - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_PL0_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E00C0, 0x013F3F07U ,0x01010F00U) - RegMask = (CRL_APB_PL0_REF_CTRL_CLKACT_MASK | CRL_APB_PL0_REF_CTRL_DIVISOR1_MASK | CRL_APB_PL0_REF_CTRL_DIVISOR0_MASK | CRL_APB_PL0_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_PL0_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_PL0_REF_CTRL_DIVISOR1_SHIFT - | 0x0000000FU << CRL_APB_PL0_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_PL0_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_PL0_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010F00U); - /*############################################################################################################################ */ - - /*Register : PL1_REF_CTRL @ 0XFF5E00C4</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_PL1_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_PL1_REF_CTRL_DIVISOR1 0x4 - - 6 bit divider - PSU_CRL_APB_PL1_REF_CTRL_DIVISOR0 0xf - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_PL1_REF_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E00C4, 0x013F3F07U ,0x01040F00U) - RegMask = (CRL_APB_PL1_REF_CTRL_CLKACT_MASK | CRL_APB_PL1_REF_CTRL_DIVISOR1_MASK | CRL_APB_PL1_REF_CTRL_DIVISOR0_MASK | CRL_APB_PL1_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_PL1_REF_CTRL_CLKACT_SHIFT - | 0x00000004U << CRL_APB_PL1_REF_CTRL_DIVISOR1_SHIFT - | 0x0000000FU << CRL_APB_PL1_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_PL1_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_PL1_REF_CTRL_OFFSET ,0x013F3F07U ,0x01040F00U); - /*############################################################################################################################ */ - - /*Register : PL2_REF_CTRL @ 0XFF5E00C8</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_PL2_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_PL2_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_PL2_REF_CTRL_DIVISOR0 0x4 - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_PL2_REF_CTRL_SRCSEL 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E00C8, 0x013F3F07U ,0x01010402U) - RegMask = (CRL_APB_PL2_REF_CTRL_CLKACT_MASK | CRL_APB_PL2_REF_CTRL_DIVISOR1_MASK | CRL_APB_PL2_REF_CTRL_DIVISOR0_MASK | CRL_APB_PL2_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_PL2_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_PL2_REF_CTRL_DIVISOR1_SHIFT - | 0x00000004U << CRL_APB_PL2_REF_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_PL2_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_PL2_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010402U); - /*############################################################################################################################ */ - - /*Register : PL3_REF_CTRL @ 0XFF5E00CC</p> - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_PL3_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRL_APB_PL3_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_PL3_REF_CTRL_DIVISOR0 0x3 - - 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_PL3_REF_CTRL_SRCSEL 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E00CC, 0x013F3F07U ,0x01010302U) - RegMask = (CRL_APB_PL3_REF_CTRL_CLKACT_MASK | CRL_APB_PL3_REF_CTRL_DIVISOR1_MASK | CRL_APB_PL3_REF_CTRL_DIVISOR0_MASK | CRL_APB_PL3_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_PL3_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRL_APB_PL3_REF_CTRL_DIVISOR1_SHIFT - | 0x00000003U << CRL_APB_PL3_REF_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_PL3_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_PL3_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010302U); - /*############################################################################################################################ */ - - /*Register : AMS_REF_CTRL @ 0XFF5E0108</p> - - 6 bit divider - PSU_CRL_APB_AMS_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRL_APB_AMS_REF_CTRL_DIVISOR0 0x1d - - 000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_AMS_REF_CTRL_SRCSEL 0x2 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_AMS_REF_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0108, 0x013F3F07U ,0x01011D02U) - RegMask = (CRL_APB_AMS_REF_CTRL_DIVISOR1_MASK | CRL_APB_AMS_REF_CTRL_DIVISOR0_MASK | CRL_APB_AMS_REF_CTRL_SRCSEL_MASK | CRL_APB_AMS_REF_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_AMS_REF_CTRL_DIVISOR1_SHIFT - | 0x0000001DU << CRL_APB_AMS_REF_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRL_APB_AMS_REF_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRL_APB_AMS_REF_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_AMS_REF_CTRL_OFFSET ,0x013F3F07U ,0x01011D02U); - /*############################################################################################################################ */ - - /*Register : DLL_REF_CTRL @ 0XFF5E0104</p> - - 000 = IOPLL; 001 = RPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new clock. This - is not usually an issue, but designers must be aware.) - PSU_CRL_APB_DLL_REF_CTRL_SRCSEL 0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0104, 0x00000007U ,0x00000000U) - RegMask = (CRL_APB_DLL_REF_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_DLL_REF_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_DLL_REF_CTRL_OFFSET ,0x00000007U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : TIMESTAMP_REF_CTRL @ 0XFF5E0128</p> - - 6 bit divider - PSU_CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0 0xf - - 1XX = pss_ref_clk; 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and - cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL 0x0 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRL_APB_TIMESTAMP_REF_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFF5E0128, 0x01003F07U ,0x01000F00U) - RegMask = (CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0_MASK | CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL_MASK | CRL_APB_TIMESTAMP_REF_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x0000000FU << CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRL_APB_TIMESTAMP_REF_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_TIMESTAMP_REF_CTRL_OFFSET ,0x01003F07U ,0x01000F00U); - /*############################################################################################################################ */ - - /*Register : SATA_REF_CTRL @ 0XFD1A00A0</p> - - 000 = IOPLL_TO_FPD; 010 = APLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_SATA_REF_CTRL_SRCSEL 0x0 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRF_APB_SATA_REF_CTRL_CLKACT 0x1 - - 6 bit divider - PSU_CRF_APB_SATA_REF_CTRL_DIVISOR0 0x2 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A00A0, 0x01003F07U ,0x01000200U) - RegMask = (CRF_APB_SATA_REF_CTRL_SRCSEL_MASK | CRF_APB_SATA_REF_CTRL_CLKACT_MASK | CRF_APB_SATA_REF_CTRL_DIVISOR0_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_SATA_REF_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_SATA_REF_CTRL_CLKACT_SHIFT - | 0x00000002U << CRF_APB_SATA_REF_CTRL_DIVISOR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_SATA_REF_CTRL_OFFSET ,0x01003F07U ,0x01000200U); - /*############################################################################################################################ */ - - /*Register : DP_VIDEO_REF_CTRL @ 0XFD1A0070</p> - - 6 bit divider - PSU_CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0 0x3 - - 000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD - might be using extra mux; (This signal may only be toggled after 4 cycles of the - ld clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL 0x3 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRF_APB_DP_VIDEO_REF_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A0070, 0x013F3F07U ,0x01010303U) - RegMask = (CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1_MASK | CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0_MASK | CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL_MASK | CRF_APB_DP_VIDEO_REF_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1_SHIFT - | 0x00000003U << CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0_SHIFT - | 0x00000003U << CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_DP_VIDEO_REF_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DP_VIDEO_REF_CTRL_OFFSET ,0x013F3F07U ,0x01010303U); - /*############################################################################################################################ */ - - /*Register : DP_AUDIO_REF_CTRL @ 0XFD1A0074</p> - - 6 bit divider - PSU_CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0 0x27 - - 000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD - might be using extra mux; (This signal may only be toggled after 4 cycles of the - ld clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL 0x0 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRF_APB_DP_AUDIO_REF_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A0074, 0x013F3F07U ,0x01012700U) - RegMask = (CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1_MASK | CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0_MASK | CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL_MASK | CRF_APB_DP_AUDIO_REF_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1_SHIFT - | 0x00000027U << CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_DP_AUDIO_REF_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DP_AUDIO_REF_CTRL_OFFSET ,0x013F3F07U ,0x01012700U); - /*############################################################################################################################ */ - - /*Register : DP_STC_REF_CTRL @ 0XFD1A007C</p> - - 6 bit divider - PSU_CRF_APB_DP_STC_REF_CTRL_DIVISOR1 0x1 - - 6 bit divider - PSU_CRF_APB_DP_STC_REF_CTRL_DIVISOR0 0x11 - - 000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of t - e new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_DP_STC_REF_CTRL_SRCSEL 0x3 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRF_APB_DP_STC_REF_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A007C, 0x013F3F07U ,0x01011103U) - RegMask = (CRF_APB_DP_STC_REF_CTRL_DIVISOR1_MASK | CRF_APB_DP_STC_REF_CTRL_DIVISOR0_MASK | CRF_APB_DP_STC_REF_CTRL_SRCSEL_MASK | CRF_APB_DP_STC_REF_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_DP_STC_REF_CTRL_DIVISOR1_SHIFT - | 0x00000011U << CRF_APB_DP_STC_REF_CTRL_DIVISOR0_SHIFT - | 0x00000003U << CRF_APB_DP_STC_REF_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_DP_STC_REF_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DP_STC_REF_CTRL_OFFSET ,0x013F3F07U ,0x01011103U); - /*############################################################################################################################ */ - - /*Register : ACPU_CTRL @ 0XFD1A0060</p> - - 6 bit divider - PSU_CRF_APB_ACPU_CTRL_DIVISOR0 0x1 - - 000 = APLL; 010 = DPLL; 011 = VPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - lock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_ACPU_CTRL_SRCSEL 0x0 - - Clock active signal. Switch to 0 to disable the clock. For the half speed APU Clock - PSU_CRF_APB_ACPU_CTRL_CLKACT_HALF 0x1 - - Clock active signal. Switch to 0 to disable the clock. For the full speed ACPUX Clock. This will shut off the high speed cloc - to the entire APU - PSU_CRF_APB_ACPU_CTRL_CLKACT_FULL 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A0060, 0x03003F07U ,0x03000100U) - RegMask = (CRF_APB_ACPU_CTRL_DIVISOR0_MASK | CRF_APB_ACPU_CTRL_SRCSEL_MASK | CRF_APB_ACPU_CTRL_CLKACT_HALF_MASK | CRF_APB_ACPU_CTRL_CLKACT_FULL_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_ACPU_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRF_APB_ACPU_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_ACPU_CTRL_CLKACT_HALF_SHIFT - | 0x00000001U << CRF_APB_ACPU_CTRL_CLKACT_FULL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_ACPU_CTRL_OFFSET ,0x03003F07U ,0x03000100U); - /*############################################################################################################################ */ - - /*Register : DBG_TRACE_CTRL @ 0XFD1A0064</p> - - 6 bit divider - PSU_CRF_APB_DBG_TRACE_CTRL_DIVISOR0 0x2 - - 000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_DBG_TRACE_CTRL_SRCSEL 0x0 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRF_APB_DBG_TRACE_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A0064, 0x01003F07U ,0x01000200U) - RegMask = (CRF_APB_DBG_TRACE_CTRL_DIVISOR0_MASK | CRF_APB_DBG_TRACE_CTRL_SRCSEL_MASK | CRF_APB_DBG_TRACE_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x00000002U << CRF_APB_DBG_TRACE_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRF_APB_DBG_TRACE_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_DBG_TRACE_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DBG_TRACE_CTRL_OFFSET ,0x01003F07U ,0x01000200U); - /*############################################################################################################################ */ - - /*Register : DBG_FPD_CTRL @ 0XFD1A0068</p> - - 6 bit divider - PSU_CRF_APB_DBG_FPD_CTRL_DIVISOR0 0x2 - - 000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_DBG_FPD_CTRL_SRCSEL 0x0 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRF_APB_DBG_FPD_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A0068, 0x01003F07U ,0x01000200U) - RegMask = (CRF_APB_DBG_FPD_CTRL_DIVISOR0_MASK | CRF_APB_DBG_FPD_CTRL_SRCSEL_MASK | CRF_APB_DBG_FPD_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x00000002U << CRF_APB_DBG_FPD_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRF_APB_DBG_FPD_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_DBG_FPD_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DBG_FPD_CTRL_OFFSET ,0x01003F07U ,0x01000200U); - /*############################################################################################################################ */ - - /*Register : DDR_CTRL @ 0XFD1A0080</p> - - 6 bit divider - PSU_CRF_APB_DDR_CTRL_DIVISOR0 0x2 - - 000 = DPLL; 001 = VPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new clock. This - s not usually an issue, but designers must be aware.) - PSU_CRF_APB_DDR_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A0080, 0x00003F07U ,0x00000200U) - RegMask = (CRF_APB_DDR_CTRL_DIVISOR0_MASK | CRF_APB_DDR_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000002U << CRF_APB_DDR_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRF_APB_DDR_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DDR_CTRL_OFFSET ,0x00003F07U ,0x00000200U); - /*############################################################################################################################ */ - - /*Register : GPU_REF_CTRL @ 0XFD1A0084</p> - - 6 bit divider - PSU_CRF_APB_GPU_REF_CTRL_DIVISOR0 0x1 - - 000 = IOPLL_TO_FPD; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_GPU_REF_CTRL_SRCSEL 0x0 - - Clock active signal. Switch to 0 to disable the clock, which will stop clock for GPU (and both Pixel Processors). - PSU_CRF_APB_GPU_REF_CTRL_CLKACT 0x1 - - Clock active signal for Pixel Processor. Switch to 0 to disable the clock only to this Pixel Processor - PSU_CRF_APB_GPU_REF_CTRL_PP0_CLKACT 0x1 - - Clock active signal for Pixel Processor. Switch to 0 to disable the clock only to this Pixel Processor - PSU_CRF_APB_GPU_REF_CTRL_PP1_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A0084, 0x07003F07U ,0x07000100U) - RegMask = (CRF_APB_GPU_REF_CTRL_DIVISOR0_MASK | CRF_APB_GPU_REF_CTRL_SRCSEL_MASK | CRF_APB_GPU_REF_CTRL_CLKACT_MASK | CRF_APB_GPU_REF_CTRL_PP0_CLKACT_MASK | CRF_APB_GPU_REF_CTRL_PP1_CLKACT_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_GPU_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRF_APB_GPU_REF_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_GPU_REF_CTRL_CLKACT_SHIFT - | 0x00000001U << CRF_APB_GPU_REF_CTRL_PP0_CLKACT_SHIFT - | 0x00000001U << CRF_APB_GPU_REF_CTRL_PP1_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_GPU_REF_CTRL_OFFSET ,0x07003F07U ,0x07000100U); - /*############################################################################################################################ */ - - /*Register : GDMA_REF_CTRL @ 0XFD1A00B8</p> - - 6 bit divider - PSU_CRF_APB_GDMA_REF_CTRL_DIVISOR0 0x2 - - 000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - lock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_GDMA_REF_CTRL_SRCSEL 0x0 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRF_APB_GDMA_REF_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A00B8, 0x01003F07U ,0x01000200U) - RegMask = (CRF_APB_GDMA_REF_CTRL_DIVISOR0_MASK | CRF_APB_GDMA_REF_CTRL_SRCSEL_MASK | CRF_APB_GDMA_REF_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x00000002U << CRF_APB_GDMA_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRF_APB_GDMA_REF_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_GDMA_REF_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_GDMA_REF_CTRL_OFFSET ,0x01003F07U ,0x01000200U); - /*############################################################################################################################ */ - - /*Register : DPDMA_REF_CTRL @ 0XFD1A00BC</p> - - 6 bit divider - PSU_CRF_APB_DPDMA_REF_CTRL_DIVISOR0 0x2 - - 000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - lock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_DPDMA_REF_CTRL_SRCSEL 0x0 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRF_APB_DPDMA_REF_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A00BC, 0x01003F07U ,0x01000200U) - RegMask = (CRF_APB_DPDMA_REF_CTRL_DIVISOR0_MASK | CRF_APB_DPDMA_REF_CTRL_SRCSEL_MASK | CRF_APB_DPDMA_REF_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x00000002U << CRF_APB_DPDMA_REF_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRF_APB_DPDMA_REF_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_DPDMA_REF_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DPDMA_REF_CTRL_OFFSET ,0x01003F07U ,0x01000200U); - /*############################################################################################################################ */ - - /*Register : TOPSW_MAIN_CTRL @ 0XFD1A00C0</p> - - 6 bit divider - PSU_CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0 0x2 - - 000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - lock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_TOPSW_MAIN_CTRL_SRCSEL 0x2 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRF_APB_TOPSW_MAIN_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A00C0, 0x01003F07U ,0x01000202U) - RegMask = (CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0_MASK | CRF_APB_TOPSW_MAIN_CTRL_SRCSEL_MASK | CRF_APB_TOPSW_MAIN_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x00000002U << CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRF_APB_TOPSW_MAIN_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_TOPSW_MAIN_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_TOPSW_MAIN_CTRL_OFFSET ,0x01003F07U ,0x01000202U); - /*############################################################################################################################ */ - - /*Register : TOPSW_LSBUS_CTRL @ 0XFD1A00C4</p> - - 6 bit divider - PSU_CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0 0x5 - - 000 = APLL; 010 = IOPLL_TO_FPD; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL 0x2 - - Clock active signal. Switch to 0 to disable the clock - PSU_CRF_APB_TOPSW_LSBUS_CTRL_CLKACT 0x1 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A00C4, 0x01003F07U ,0x01000502U) - RegMask = (CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0_MASK | CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL_MASK | CRF_APB_TOPSW_LSBUS_CTRL_CLKACT_MASK | 0 ); - - RegVal = ((0x00000005U << CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0_SHIFT - | 0x00000002U << CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL_SHIFT - | 0x00000001U << CRF_APB_TOPSW_LSBUS_CTRL_CLKACT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_TOPSW_LSBUS_CTRL_OFFSET ,0x01003F07U ,0x01000502U); - /*############################################################################################################################ */ - - /*Register : DBG_TSTMP_CTRL @ 0XFD1A00F8</p> - - 6 bit divider - PSU_CRF_APB_DBG_TSTMP_CTRL_DIVISOR0 0x2 - - 000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.) - PSU_CRF_APB_DBG_TSTMP_CTRL_SRCSEL 0x0 - - This register controls this reference clock - (OFFSET, MASK, VALUE) (0XFD1A00F8, 0x00003F07U ,0x00000200U) - RegMask = (CRF_APB_DBG_TSTMP_CTRL_DIVISOR0_MASK | CRF_APB_DBG_TSTMP_CTRL_SRCSEL_MASK | 0 ); - - RegVal = ((0x00000002U << CRF_APB_DBG_TSTMP_CTRL_DIVISOR0_SHIFT - | 0x00000000U << CRF_APB_DBG_TSTMP_CTRL_SRCSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_DBG_TSTMP_CTRL_OFFSET ,0x00003F07U ,0x00000200U); - /*############################################################################################################################ */ - - /*Register : IOU_TTC_APB_CLK @ 0XFF180380</p> - - 00" = Select the APB switch clock for the APB interface of TTC0'01" = Select the PLL ref clock for the APB interface of TTC0' - 0" = Select the R5 clock for the APB interface of TTC0 - PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL 0 - - 00" = Select the APB switch clock for the APB interface of TTC1'01" = Select the PLL ref clock for the APB interface of TTC1' - 0" = Select the R5 clock for the APB interface of TTC1 - PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL 0 - - 00" = Select the APB switch clock for the APB interface of TTC2'01" = Select the PLL ref clock for the APB interface of TTC2' - 0" = Select the R5 clock for the APB interface of TTC2 - PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL 0 - - 00" = Select the APB switch clock for the APB interface of TTC3'01" = Select the PLL ref clock for the APB interface of TTC3' - 0" = Select the R5 clock for the APB interface of TTC3 - PSU_IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL 0 - - TTC APB clock select - (OFFSET, MASK, VALUE) (0XFF180380, 0x000000FFU ,0x00000000U) - RegMask = (IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL_MASK | IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL_MASK | IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL_MASK | IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_IOU_TTC_APB_CLK_OFFSET ,0x000000FFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : WDT_CLK_SEL @ 0XFD610100</p> - - System watchdog timer clock source selection: 0: Internal APB clock 1: External (PL clock via EMIO or Pinout clock via MIO) - PSU_FPD_SLCR_WDT_CLK_SEL_SELECT 0 - - SWDT clock source select - (OFFSET, MASK, VALUE) (0XFD610100, 0x00000001U ,0x00000000U) - RegMask = (FPD_SLCR_WDT_CLK_SEL_SELECT_MASK | 0 ); - - RegVal = ((0x00000000U << FPD_SLCR_WDT_CLK_SEL_SELECT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (FPD_SLCR_WDT_CLK_SEL_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : WDT_CLK_SEL @ 0XFF180300</p> - - System watchdog timer clock source selection: 0: internal clock APB clock 1: external clock from PL via EMIO, or from pinout - ia MIO - PSU_IOU_SLCR_WDT_CLK_SEL_SELECT 0 - - SWDT clock source select - (OFFSET, MASK, VALUE) (0XFF180300, 0x00000001U ,0x00000000U) - RegMask = (IOU_SLCR_WDT_CLK_SEL_SELECT_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_WDT_CLK_SEL_SELECT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_WDT_CLK_SEL_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : CSUPMU_WDT_CLK_SEL @ 0XFF410050</p> - - System watchdog timer clock source selection: 0: internal clock APB clock 1: external clock pss_ref_clk - PSU_LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT 0 - - SWDT clock source select - (OFFSET, MASK, VALUE) (0XFF410050, 0x00000001U ,0x00000000U) - RegMask = (LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT_MASK | 0 ); - - RegVal = ((0x00000000U << LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_SLCR_CSUPMU_WDT_CLK_SEL_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - - return 1; -} -unsigned long psu_ddr_init_data() { - // : DDR INITIALIZATION - // : DDR CONTROLLER RESET - /*Register : RST_DDR_SS @ 0XFD1A0108</p> - - DDR block level reset inside of the DDR Sub System - PSU_CRF_APB_RST_DDR_SS_DDR_RESET 0X1 - - DDR sub system block level reset - (OFFSET, MASK, VALUE) (0XFD1A0108, 0x00000008U ,0x00000008U) - RegMask = (CRF_APB_RST_DDR_SS_DDR_RESET_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_RST_DDR_SS_DDR_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_RST_DDR_SS_OFFSET ,0x00000008U ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : MSTR @ 0XFD070000</p> - - Indicates the configuration of the device used in the system. - 00 - x4 device - 01 - x8 device - 10 - x16 device - 11 - x32 - evice - PSU_DDRC_MSTR_DEVICE_CONFIG 0x1 - - Choose which registers are used. - 0 - Original registers - 1 - Shadow registers - PSU_DDRC_MSTR_FREQUENCY_MODE 0x0 - - Only present for multi-rank configurations. Each bit represents one rank. For two-rank configurations, only bits[25:24] are p - esent. - 1 - populated - 0 - unpopulated LSB is the lowest rank number. For 2 ranks following combinations are legal: - 01 - - ne rank - 11 - Two ranks - Others - Reserved. For 4 ranks following combinations are legal: - 0001 - One rank - 0011 - Two ra - ks - 1111 - Four ranks - PSU_DDRC_MSTR_ACTIVE_RANKS 0x1 - - SDRAM burst length used: - 0001 - Burst length of 2 (only supported for mDDR) - 0010 - Burst length of 4 - 0100 - Burst lengt - of 8 - 1000 - Burst length of 16 (only supported for mDDR, LPDDR2, and LPDDR4) All other values are reserved. This controls - he burst size used to access the SDRAM. This must match the burst length mode register setting in the SDRAM. (For BC4/8 on-th - -fly mode of DDR3 and DDR4, set this field to 0x0100) Burst length of 2 is not supported with AXI ports when MEMC_BURST_LENGT - is 8. Burst length of 2 is only supported with MEMC_FREQ_RATIO = 1 - PSU_DDRC_MSTR_BURST_RDWR 0x4 - - Set to 1 when the uMCTL2 and DRAM has to be put in DLL-off mode for low frequency operation. Set to 0 to put uMCTL2 and DRAM - n DLL-on mode for normal frequency operation. If DDR4 CRC/parity retry is enabled (CRCPARCTL1.crc_parity_retry_enable = 1), d - l_off_mode is not supported, and this bit must be set to '0'. - PSU_DDRC_MSTR_DLL_OFF_MODE 0x0 - - Selects proportion of DQ bus width that is used by the SDRAM - 00 - Full DQ bus width to SDRAM - 01 - Half DQ bus width to SD - AM - 10 - Quarter DQ bus width to SDRAM - 11 - Reserved. Note that half bus width mode is only supported when the SDRAM bus w - dth is a multiple of 16, and quarter bus width mode is only supported when the SDRAM bus width is a multiple of 32 and the co - figuration parameter MEMC_QBUS_SUPPORT is set. Bus width refers to DQ bus width (excluding any ECC width). - PSU_DDRC_MSTR_DATA_BUS_WIDTH 0x0 - - 1 indicates put the DRAM in geardown mode (2N) and 0 indicates put the DRAM in normal mode (1N). This register can be changed - only when the Controller is in self-refresh mode. This signal must be set the same value as MR3 bit A3. Note: Geardown mode - s not supported if the configuration parameter MEMC_CMD_RTN2IDLE is set - PSU_DDRC_MSTR_GEARDOWN_MODE 0x0 - - If 1, then uMCTL2 uses 2T timing. Otherwise, uses 1T timing. In 2T timing, all command signals (except chip select) are held - or 2 clocks on the SDRAM bus. Chip select is asserted on the second cycle of the command Note: 2T timing is not supported in - PDDR2/LPDDR3/LPDDR4 mode Note: 2T timing is not supported if the configuration parameter MEMC_CMD_RTN2IDLE is set Note: 2T ti - ing is not supported in DDR4 geardown mode. - PSU_DDRC_MSTR_EN_2T_TIMING_MODE 0x0 - - When set, enable burst-chop in DDR3/DDR4. Burst Chop for Reads is exercised only in HIF configurations (UMCTL2_INCL_ARB not s - t) and if in full bus width mode (MSTR.data_bus_width = 00). Burst Chop for Writes is exercised only if Partial Writes enable - (UMCTL2_PARTIAL_WR=1) and if CRC is disabled (CRCPARCTL1.crc_enable = 0). If DDR4 CRC/parity retry is enabled (CRCPARCTL1.cr - _parity_retry_enable = 1), burst chop is not supported, and this bit must be set to '0' - PSU_DDRC_MSTR_BURSTCHOP 0x0 - - Select LPDDR4 SDRAM - 1 - LPDDR4 SDRAM device in use. - 0 - non-LPDDR4 device in use Present only in designs configured to su - port LPDDR4. - PSU_DDRC_MSTR_LPDDR4 0x0 - - Select DDR4 SDRAM - 1 - DDR4 SDRAM device in use. - 0 - non-DDR4 device in use Present only in designs configured to support - DR4. - PSU_DDRC_MSTR_DDR4 0x1 - - Select LPDDR3 SDRAM - 1 - LPDDR3 SDRAM device in use. - 0 - non-LPDDR3 device in use Present only in designs configured to su - port LPDDR3. - PSU_DDRC_MSTR_LPDDR3 0x0 - - Select LPDDR2 SDRAM - 1 - LPDDR2 SDRAM device in use. - 0 - non-LPDDR2 device in use Present only in designs configured to su - port LPDDR2. - PSU_DDRC_MSTR_LPDDR2 0x0 - - Select DDR3 SDRAM - 1 - DDR3 SDRAM device in use - 0 - non-DDR3 SDRAM device in use Only present in designs that support DDR3 - - PSU_DDRC_MSTR_DDR3 0x0 - - Master Register - (OFFSET, MASK, VALUE) (0XFD070000, 0xE30FBE3DU ,0x41040010U) - RegMask = (DDRC_MSTR_DEVICE_CONFIG_MASK | DDRC_MSTR_FREQUENCY_MODE_MASK | DDRC_MSTR_ACTIVE_RANKS_MASK | DDRC_MSTR_BURST_RDWR_MASK | DDRC_MSTR_DLL_OFF_MODE_MASK | DDRC_MSTR_DATA_BUS_WIDTH_MASK | DDRC_MSTR_GEARDOWN_MODE_MASK | DDRC_MSTR_EN_2T_TIMING_MODE_MASK | DDRC_MSTR_BURSTCHOP_MASK | DDRC_MSTR_LPDDR4_MASK | DDRC_MSTR_DDR4_MASK | DDRC_MSTR_LPDDR3_MASK | DDRC_MSTR_LPDDR2_MASK | DDRC_MSTR_DDR3_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_MSTR_DEVICE_CONFIG_SHIFT - | 0x00000000U << DDRC_MSTR_FREQUENCY_MODE_SHIFT - | 0x00000001U << DDRC_MSTR_ACTIVE_RANKS_SHIFT - | 0x00000004U << DDRC_MSTR_BURST_RDWR_SHIFT - | 0x00000000U << DDRC_MSTR_DLL_OFF_MODE_SHIFT - | 0x00000000U << DDRC_MSTR_DATA_BUS_WIDTH_SHIFT - | 0x00000000U << DDRC_MSTR_GEARDOWN_MODE_SHIFT - | 0x00000000U << DDRC_MSTR_EN_2T_TIMING_MODE_SHIFT - | 0x00000000U << DDRC_MSTR_BURSTCHOP_SHIFT - | 0x00000000U << DDRC_MSTR_LPDDR4_SHIFT - | 0x00000001U << DDRC_MSTR_DDR4_SHIFT - | 0x00000000U << DDRC_MSTR_LPDDR3_SHIFT - | 0x00000000U << DDRC_MSTR_LPDDR2_SHIFT - | 0x00000000U << DDRC_MSTR_DDR3_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_MSTR_OFFSET ,0xE30FBE3DU ,0x41040010U); - /*############################################################################################################################ */ - - /*Register : MRCTRL0 @ 0XFD070010</p> - - Setting this register bit to 1 triggers a mode register read or write operation. When the MR operation is complete, the uMCTL - automatically clears this bit. The other register fields of this register must be written in a separate APB transaction, bef - re setting this mr_wr bit. It is recommended NOT to set this signal if in Init, Deep power-down or MPSM operating modes. - PSU_DDRC_MRCTRL0_MR_WR 0x0 - - Address of the mode register that is to be written to. - 0000 - MR0 - 0001 - MR1 - 0010 - MR2 - 0011 - MR3 - 0100 - MR4 - 010 - - MR5 - 0110 - MR6 - 0111 - MR7 Don't Care for LPDDR2/LPDDR3/LPDDR4 (see MRCTRL1.mr_data for mode register addressing in LPD - R2/LPDDR3/LPDDR4) This signal is also used for writing to control words of RDIMMs. In that case, it corresponds to the bank a - dress bits sent to the RDIMM In case of DDR4, the bit[3:2] corresponds to the bank group bits. Therefore, the bit[3] as well - s the bit[2:0] must be set to an appropriate value which is considered both the Address Mirroring of UDIMMs/RDIMMs and the Ou - put Inversion of RDIMMs. - PSU_DDRC_MRCTRL0_MR_ADDR 0x0 - - Controls which rank is accessed by MRCTRL0.mr_wr. Normally, it is desired to access all ranks, so all bits should be set to 1 - However, for multi-rank UDIMMs/RDIMMs which implement address mirroring, it may be necessary to access ranks individually. E - amples (assume uMCTL2 is configured for 4 ranks): - 0x1 - select rank 0 only - 0x2 - select rank 1 only - 0x5 - select ranks - and 2 - 0xA - select ranks 1 and 3 - 0xF - select ranks 0, 1, 2 and 3 - PSU_DDRC_MRCTRL0_MR_RANK 0x3 - - Indicates whether Software intervention is allowed via MRCTRL0/MRCTRL1 before automatic SDRAM initialization routine or not. - or DDR4, this bit can be used to initialize the DDR4 RCD (MR7) before automatic SDRAM initialization. For LPDDR4, this bit ca - be used to program additional mode registers before automatic SDRAM initialization if necessary. Note: This must be cleared - o 0 after completing Software operation. Otherwise, SDRAM initialization routine will not re-start. - 0 - Software interventi - n is not allowed - 1 - Software intervention is allowed - PSU_DDRC_MRCTRL0_SW_INIT_INT 0x0 - - Indicates whether the mode register operation is MRS in PDA mode or not - 0 - MRS - 1 - MRS in Per DRAM Addressability mode - PSU_DDRC_MRCTRL0_PDA_EN 0x0 - - Indicates whether the mode register operation is MRS or WR/RD for MPR (only supported for DDR4) - 0 - MRS - 1 - WR/RD for MPR - PSU_DDRC_MRCTRL0_MPR_EN 0x0 - - Indicates whether the mode register operation is read or write. Only used for LPDDR2/LPDDR3/LPDDR4/DDR4. - 0 - Write - 1 - Re - d - PSU_DDRC_MRCTRL0_MR_TYPE 0x0 - - Mode Register Read/Write Control Register 0. Note: Do not enable more than one of the following fields simultaneously: - sw_i - it_int - pda_en - mpr_en - (OFFSET, MASK, VALUE) (0XFD070010, 0x8000F03FU ,0x00000030U) - RegMask = (DDRC_MRCTRL0_MR_WR_MASK | DDRC_MRCTRL0_MR_ADDR_MASK | DDRC_MRCTRL0_MR_RANK_MASK | DDRC_MRCTRL0_SW_INIT_INT_MASK | DDRC_MRCTRL0_PDA_EN_MASK | DDRC_MRCTRL0_MPR_EN_MASK | DDRC_MRCTRL0_MR_TYPE_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_MRCTRL0_MR_WR_SHIFT - | 0x00000000U << DDRC_MRCTRL0_MR_ADDR_SHIFT - | 0x00000003U << DDRC_MRCTRL0_MR_RANK_SHIFT - | 0x00000000U << DDRC_MRCTRL0_SW_INIT_INT_SHIFT - | 0x00000000U << DDRC_MRCTRL0_PDA_EN_SHIFT - | 0x00000000U << DDRC_MRCTRL0_MPR_EN_SHIFT - | 0x00000000U << DDRC_MRCTRL0_MR_TYPE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_MRCTRL0_OFFSET ,0x8000F03FU ,0x00000030U); - /*############################################################################################################################ */ - - /*Register : DERATEEN @ 0XFD070020</p> - - Derate value of tRC for LPDDR4 - 0 - Derating uses +1. - 1 - Derating uses +2. - 2 - Derating uses +3. - 3 - Derating uses +4 - Present only in designs configured to support LPDDR4. The required number of cycles for derating can be determined by dividi - g 3.75ns by the core_ddrc_core_clk period, and rounding up the next integer. - PSU_DDRC_DERATEEN_RC_DERATE_VALUE 0x3 - - Derate byte Present only in designs configured to support LPDDR2/LPDDR3/LPDDR4 Indicates which byte of the MRR data is used f - r derating. The maximum valid value depends on MEMC_DRAM_TOTAL_DATA_WIDTH. - PSU_DDRC_DERATEEN_DERATE_BYTE 0x0 - - Derate value - 0 - Derating uses +1. - 1 - Derating uses +2. Present only in designs configured to support LPDDR2/LPDDR3/LPDD - 4 Set to 0 for all LPDDR2 speed grades as derating value of +1.875 ns is less than a core_ddrc_core_clk period. Can be 0 or 1 - for LPDDR3/LPDDR4, depending if +1.875 ns is less than a core_ddrc_core_clk period or not. - PSU_DDRC_DERATEEN_DERATE_VALUE 0x0 - - Enables derating - 0 - Timing parameter derating is disabled - 1 - Timing parameter derating is enabled using MR4 read value. - Present only in designs configured to support LPDDR2/LPDDR3/LPDDR4 This field must be set to '0' for non-LPDDR2/LPDDR3/LPDDR4 - mode. - PSU_DDRC_DERATEEN_DERATE_ENABLE 0x0 - - Temperature Derate Enable Register - (OFFSET, MASK, VALUE) (0XFD070020, 0x000003F3U ,0x00000300U) - RegMask = (DDRC_DERATEEN_RC_DERATE_VALUE_MASK | DDRC_DERATEEN_DERATE_BYTE_MASK | DDRC_DERATEEN_DERATE_VALUE_MASK | DDRC_DERATEEN_DERATE_ENABLE_MASK | 0 ); - - RegVal = ((0x00000003U << DDRC_DERATEEN_RC_DERATE_VALUE_SHIFT - | 0x00000000U << DDRC_DERATEEN_DERATE_BYTE_SHIFT - | 0x00000000U << DDRC_DERATEEN_DERATE_VALUE_SHIFT - | 0x00000000U << DDRC_DERATEEN_DERATE_ENABLE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DERATEEN_OFFSET ,0x000003F3U ,0x00000300U); - /*############################################################################################################################ */ - - /*Register : DERATEINT @ 0XFD070024</p> - - Interval between two MR4 reads, used to derate the timing parameters. Present only in designs configured to support LPDDR2/LP - DR3/LPDDR4. This register must not be set to zero - PSU_DDRC_DERATEINT_MR4_READ_INTERVAL 0x800000 - - Temperature Derate Interval Register - (OFFSET, MASK, VALUE) (0XFD070024, 0xFFFFFFFFU ,0x00800000U) - RegMask = (DDRC_DERATEINT_MR4_READ_INTERVAL_MASK | 0 ); - - RegVal = ((0x00800000U << DDRC_DERATEINT_MR4_READ_INTERVAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DERATEINT_OFFSET ,0xFFFFFFFFU ,0x00800000U); - /*############################################################################################################################ */ - - /*Register : PWRCTL @ 0XFD070030</p> - - Self refresh state is an intermediate state to enter to Self refresh power down state or exit Self refresh power down state f - r LPDDR4. This register controls transition from the Self refresh state. - 1 - Prohibit transition from Self refresh state - - - Allow transition from Self refresh state - PSU_DDRC_PWRCTL_STAY_IN_SELFREF 0x0 - - A value of 1 to this register causes system to move to Self Refresh state immediately, as long as it is not in INIT or DPD/MP - M operating_mode. This is referred to as Software Entry/Exit to Self Refresh. - 1 - Software Entry to Self Refresh - 0 - Soft - are Exit from Self Refresh - PSU_DDRC_PWRCTL_SELFREF_SW 0x0 - - When this is 1, the uMCTL2 puts the SDRAM into maximum power saving mode when the transaction store is empty. This register m - st be reset to '0' to bring uMCTL2 out of maximum power saving mode. Present only in designs configured to support DDR4. For - on-DDR4, this register should not be set to 1. Note that MPSM is not supported when using a DWC DDR PHY, if the PHY parameter - DWC_AC_CS_USE is disabled, as the MPSM exit sequence requires the chip-select signal to toggle. FOR PERFORMANCE ONLY. - PSU_DDRC_PWRCTL_MPSM_EN 0x0 - - Enable the assertion of dfi_dram_clk_disable whenever a clock is not required by the SDRAM. If set to 0, dfi_dram_clk_disable - is never asserted. Assertion of dfi_dram_clk_disable is as follows: In DDR2/DDR3, can only be asserted in Self Refresh. In DD - 4, can be asserted in following: - in Self Refresh. - in Maximum Power Saving Mode In mDDR/LPDDR2/LPDDR3, can be asserted in - ollowing: - in Self Refresh - in Power Down - in Deep Power Down - during Normal operation (Clock Stop) In LPDDR4, can be ass - rted in following: - in Self Refresh Power Down - in Power Down - during Normal operation (Clock Stop) - PSU_DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE 0x0 - - When this is 1, uMCTL2 puts the SDRAM into deep power-down mode when the transaction store is empty. This register must be re - et to '0' to bring uMCTL2 out of deep power-down mode. Controller performs automatic SDRAM initialization on deep power-down - xit. Present only in designs configured to support mDDR or LPDDR2 or LPDDR3. For non-mDDR/non-LPDDR2/non-LPDDR3, this registe - should not be set to 1. FOR PERFORMANCE ONLY. - PSU_DDRC_PWRCTL_DEEPPOWERDOWN_EN 0x0 - - If true then the uMCTL2 goes into power-down after a programmable number of cycles 'maximum idle clocks before power down' (P - RTMG.powerdown_to_x32). This register bit may be re-programmed during the course of normal operation. - PSU_DDRC_PWRCTL_POWERDOWN_EN 0x0 - - If true then the uMCTL2 puts the SDRAM into Self Refresh after a programmable number of cycles 'maximum idle clocks before Se - f Refresh (PWRTMG.selfref_to_x32)'. This register bit may be re-programmed during the course of normal operation. - PSU_DDRC_PWRCTL_SELFREF_EN 0x0 - - Low Power Control Register - (OFFSET, MASK, VALUE) (0XFD070030, 0x0000007FU ,0x00000000U) - RegMask = (DDRC_PWRCTL_STAY_IN_SELFREF_MASK | DDRC_PWRCTL_SELFREF_SW_MASK | DDRC_PWRCTL_MPSM_EN_MASK | DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE_MASK | DDRC_PWRCTL_DEEPPOWERDOWN_EN_MASK | DDRC_PWRCTL_POWERDOWN_EN_MASK | DDRC_PWRCTL_SELFREF_EN_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PWRCTL_STAY_IN_SELFREF_SHIFT - | 0x00000000U << DDRC_PWRCTL_SELFREF_SW_SHIFT - | 0x00000000U << DDRC_PWRCTL_MPSM_EN_SHIFT - | 0x00000000U << DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE_SHIFT - | 0x00000000U << DDRC_PWRCTL_DEEPPOWERDOWN_EN_SHIFT - | 0x00000000U << DDRC_PWRCTL_POWERDOWN_EN_SHIFT - | 0x00000000U << DDRC_PWRCTL_SELFREF_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PWRCTL_OFFSET ,0x0000007FU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : PWRTMG @ 0XFD070034</p> - - After this many clocks of NOP or deselect the uMCTL2 automatically puts the SDRAM into Self Refresh. This must be enabled in - he PWRCTL.selfref_en. Unit: Multiples of 32 clocks. FOR PERFORMANCE ONLY. - PSU_DDRC_PWRTMG_SELFREF_TO_X32 0x40 - - Minimum deep power-down time. For mDDR, value from the JEDEC specification is 0 as mDDR exits from deep power-down mode immed - ately after PWRCTL.deeppowerdown_en is de-asserted. For LPDDR2/LPDDR3, value from the JEDEC specification is 500us. Unit: Mul - iples of 4096 clocks. Present only in designs configured to support mDDR, LPDDR2 or LPDDR3. FOR PERFORMANCE ONLY. - PSU_DDRC_PWRTMG_T_DPD_X4096 0x84 - - After this many clocks of NOP or deselect the uMCTL2 automatically puts the SDRAM into power-down. This must be enabled in th - PWRCTL.powerdown_en. Unit: Multiples of 32 clocks FOR PERFORMANCE ONLY. - PSU_DDRC_PWRTMG_POWERDOWN_TO_X32 0x10 - - Low Power Timing Register - (OFFSET, MASK, VALUE) (0XFD070034, 0x00FFFF1FU ,0x00408410U) - RegMask = (DDRC_PWRTMG_SELFREF_TO_X32_MASK | DDRC_PWRTMG_T_DPD_X4096_MASK | DDRC_PWRTMG_POWERDOWN_TO_X32_MASK | 0 ); - - RegVal = ((0x00000040U << DDRC_PWRTMG_SELFREF_TO_X32_SHIFT - | 0x00000084U << DDRC_PWRTMG_T_DPD_X4096_SHIFT - | 0x00000010U << DDRC_PWRTMG_POWERDOWN_TO_X32_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PWRTMG_OFFSET ,0x00FFFF1FU ,0x00408410U); - /*############################################################################################################################ */ - - /*Register : RFSHCTL0 @ 0XFD070050</p> - - Threshold value in number of clock cycles before the critical refresh or page timer expires. A critical refresh is to be issu - d before this threshold is reached. It is recommended that this not be changed from the default value, currently shown as 0x2 - It must always be less than internally used t_rfc_nom_x32. Note that, in LPDDR2/LPDDR3/LPDDR4, internally used t_rfc_nom_x32 - may be equal to RFSHTMG.t_rfc_nom_x32>>2 if derating is enabled (DERATEEN.derate_enable=1). Otherwise, internally used t_rfc_ - om_x32 will be equal to RFSHTMG.t_rfc_nom_x32. Unit: Multiples of 32 clocks. - PSU_DDRC_RFSHCTL0_REFRESH_MARGIN 0x2 - - If the refresh timer (tRFCnom, also known as tREFI) has expired at least once, but it has not expired (RFSHCTL0.refresh_burst - 1) times yet, then a speculative refresh may be performed. A speculative refresh is a refresh performed at a time when refres - would be useful, but before it is absolutely required. When the SDRAM bus is idle for a period of time determined by this RF - HCTL0.refresh_to_x32 and the refresh timer has expired at least once since the last refresh, then a speculative refresh is pe - formed. Speculative refreshes continues successively until there are no refreshes pending or until new reads or writes are is - ued to the uMCTL2. FOR PERFORMANCE ONLY. - PSU_DDRC_RFSHCTL0_REFRESH_TO_X32 0x10 - - The programmed value + 1 is the number of refresh timeouts that is allowed to accumulate before traffic is blocked and the re - reshes are forced to execute. Closing pages to perform a refresh is a one-time penalty that must be paid for each group of re - reshes. Therefore, performing refreshes in a burst reduces the per-refresh penalty of these page closings. Higher numbers for - RFSHCTL.refresh_burst slightly increases utilization; lower numbers decreases the worst-case latency associated with refreshe - . - 0 - single refresh - 1 - burst-of-2 refresh - 7 - burst-of-8 refresh For information on burst refresh feature refer to se - tion 3.9 of DDR2 JEDEC specification - JESD79-2F.pdf. For DDR2/3, the refresh is always per-rank and not per-bank. The rank r - fresh can be accumulated over 8*tREFI cycles using the burst refresh feature. In DDR4 mode, according to Fine Granularity fea - ure, 8 refreshes can be postponed in 1X mode, 16 refreshes in 2X mode and 32 refreshes in 4X mode. If using PHY-initiated upd - tes, care must be taken in the setting of RFSHCTL0.refresh_burst, to ensure that tRFCmax is not violated due to a PHY-initiat - d update occurring shortly before a refresh burst was due. In this situation, the refresh burst will be delayed until the PHY - initiated update is complete. - PSU_DDRC_RFSHCTL0_REFRESH_BURST 0x0 - - - 1 - Per bank refresh; - 0 - All bank refresh. Per bank refresh allows traffic to flow to other banks. Per bank refresh is n - t supported by all LPDDR2 devices but should be supported by all LPDDR3/LPDDR4 devices. Present only in designs configured to - support LPDDR2/LPDDR3/LPDDR4 - PSU_DDRC_RFSHCTL0_PER_BANK_REFRESH 0x0 - - Refresh Control Register 0 - (OFFSET, MASK, VALUE) (0XFD070050, 0x00F1F1F4U ,0x00210000U) - RegMask = (DDRC_RFSHCTL0_REFRESH_MARGIN_MASK | DDRC_RFSHCTL0_REFRESH_TO_X32_MASK | DDRC_RFSHCTL0_REFRESH_BURST_MASK | DDRC_RFSHCTL0_PER_BANK_REFRESH_MASK | 0 ); - - RegVal = ((0x00000002U << DDRC_RFSHCTL0_REFRESH_MARGIN_SHIFT - | 0x00000010U << DDRC_RFSHCTL0_REFRESH_TO_X32_SHIFT - | 0x00000000U << DDRC_RFSHCTL0_REFRESH_BURST_SHIFT - | 0x00000000U << DDRC_RFSHCTL0_PER_BANK_REFRESH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_RFSHCTL0_OFFSET ,0x00F1F1F4U ,0x00210000U); - /*############################################################################################################################ */ - - /*Register : RFSHCTL3 @ 0XFD070060</p> - - Fine Granularity Refresh Mode - 000 - Fixed 1x (Normal mode) - 001 - Fixed 2x - 010 - Fixed 4x - 101 - Enable on the fly 2x ( - ot supported) - 110 - Enable on the fly 4x (not supported) - Everything else - reserved Note: The on-the-fly modes is not sup - orted in this version of the uMCTL2. Note: This must be set up while the Controller is in reset or while the Controller is in - self-refresh mode. Changing this during normal operation is not allowed. Making this a dynamic register will be supported in - uture version of the uMCTL2. - PSU_DDRC_RFSHCTL3_REFRESH_MODE 0x0 - - Toggle this signal (either from 0 to 1 or from 1 to 0) to indicate that the refresh register(s) have been updated. The value - s automatically updated when exiting reset, so it does not need to be toggled initially. - PSU_DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL 0x0 - - When '1', disable auto-refresh generated by the uMCTL2. When auto-refresh is disabled, the SoC core must generate refreshes u - ing the registers reg_ddrc_rank0_refresh, reg_ddrc_rank1_refresh, reg_ddrc_rank2_refresh and reg_ddrc_rank3_refresh. When dis - auto_refresh transitions from 0 to 1, any pending refreshes are immediately scheduled by the uMCTL2. If DDR4 CRC/parity retry - is enabled (CRCPARCTL1.crc_parity_retry_enable = 1), disable auto-refresh is not supported, and this bit must be set to '0'. - his register field is changeable on the fly. - PSU_DDRC_RFSHCTL3_DIS_AUTO_REFRESH 0x1 - - Refresh Control Register 3 - (OFFSET, MASK, VALUE) (0XFD070060, 0x00000073U ,0x00000001U) - RegMask = (DDRC_RFSHCTL3_REFRESH_MODE_MASK | DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL_MASK | DDRC_RFSHCTL3_DIS_AUTO_REFRESH_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_RFSHCTL3_REFRESH_MODE_SHIFT - | 0x00000000U << DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL_SHIFT - | 0x00000001U << DDRC_RFSHCTL3_DIS_AUTO_REFRESH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_RFSHCTL3_OFFSET ,0x00000073U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : RFSHTMG @ 0XFD070064</p> - - tREFI: Average time interval between refreshes per rank (Specification: 7.8us for DDR2, DDR3 and DDR4. See JEDEC specificatio - for mDDR, LPDDR2, LPDDR3 and LPDDR4). For LPDDR2/LPDDR3/LPDDR4: - if using all-bank refreshes (RFSHCTL0.per_bank_refresh = 0 - , this register should be set to tREFIab - if using per-bank refreshes (RFSHCTL0.per_bank_refresh = 1), this register should - e set to tREFIpb For configurations with MEMC_FREQ_RATIO=2, program this to (tREFI/2), no rounding up. In DDR4 mode, tREFI va - ue is different depending on the refresh mode. The user should program the appropriate value from the spec based on the value - programmed in the refresh mode register. Note that RFSHTMG.t_rfc_nom_x32 * 32 must be greater than RFSHTMG.t_rfc_min, and RFS - TMG.t_rfc_nom_x32 must be greater than 0x1. Unit: Multiples of 32 clocks. - PSU_DDRC_RFSHTMG_T_RFC_NOM_X32 0x82 - - Used only when LPDDR3 memory type is connected. Should only be changed when uMCTL2 is in reset. Specifies whether to use the - REFBW parameter (required by some LPDDR3 devices which comply with earlier versions of the LPDDR3 JEDEC specification) or not - - 0 - tREFBW parameter not used - 1 - tREFBW parameter used - PSU_DDRC_RFSHTMG_LPDDR3_TREFBW_EN 0x1 - - tRFC (min): Minimum time from refresh to refresh or activate. For MEMC_FREQ_RATIO=1 configurations, t_rfc_min should be set t - RoundUp(tRFCmin/tCK). For MEMC_FREQ_RATIO=2 configurations, t_rfc_min should be set to RoundUp(RoundUp(tRFCmin/tCK)/2). In L - DDR2/LPDDR3/LPDDR4 mode: - if using all-bank refreshes, the tRFCmin value in the above equations is equal to tRFCab - if usin - per-bank refreshes, the tRFCmin value in the above equations is equal to tRFCpb In DDR4 mode, the tRFCmin value in the above - equations is different depending on the refresh mode (fixed 1X,2X,4X) and the device density. The user should program the app - opriate value from the spec based on the 'refresh_mode' and the device density that is used. Unit: Clocks. - PSU_DDRC_RFSHTMG_T_RFC_MIN 0x8b - - Refresh Timing Register - (OFFSET, MASK, VALUE) (0XFD070064, 0x0FFF83FFU ,0x0082808BU) - RegMask = (DDRC_RFSHTMG_T_RFC_NOM_X32_MASK | DDRC_RFSHTMG_LPDDR3_TREFBW_EN_MASK | DDRC_RFSHTMG_T_RFC_MIN_MASK | 0 ); - - RegVal = ((0x00000082U << DDRC_RFSHTMG_T_RFC_NOM_X32_SHIFT - | 0x00000001U << DDRC_RFSHTMG_LPDDR3_TREFBW_EN_SHIFT - | 0x0000008BU << DDRC_RFSHTMG_T_RFC_MIN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_RFSHTMG_OFFSET ,0x0FFF83FFU ,0x0082808BU); - /*############################################################################################################################ */ - - /*Register : ECCCFG0 @ 0XFD070070</p> - - Disable ECC scrubs. Valid only when ECCCFG0.ecc_mode = 3'b100 and MEMC_USE_RMW is defined - PSU_DDRC_ECCCFG0_DIS_SCRUB 0x1 - - ECC mode indicator - 000 - ECC disabled - 100 - ECC enabled - SEC/DED over 1 beat - all other settings are reserved for futur - use - PSU_DDRC_ECCCFG0_ECC_MODE 0x0 - - ECC Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD070070, 0x00000017U ,0x00000010U) - RegMask = (DDRC_ECCCFG0_DIS_SCRUB_MASK | DDRC_ECCCFG0_ECC_MODE_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_ECCCFG0_DIS_SCRUB_SHIFT - | 0x00000000U << DDRC_ECCCFG0_ECC_MODE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ECCCFG0_OFFSET ,0x00000017U ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : ECCCFG1 @ 0XFD070074</p> - - Selects whether to poison 1 or 2 bits - if 0 -> 2-bit (uncorrectable) data poisoning, if 1 -> 1-bit (correctable) data poison - ng, if ECCCFG1.data_poison_en=1 - PSU_DDRC_ECCCFG1_DATA_POISON_BIT 0x0 - - Enable ECC data poisoning - introduces ECC errors on writes to address specified by the ECCPOISONADDR0/1 registers - PSU_DDRC_ECCCFG1_DATA_POISON_EN 0x0 - - ECC Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD070074, 0x00000003U ,0x00000000U) - RegMask = (DDRC_ECCCFG1_DATA_POISON_BIT_MASK | DDRC_ECCCFG1_DATA_POISON_EN_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_ECCCFG1_DATA_POISON_BIT_SHIFT - | 0x00000000U << DDRC_ECCCFG1_DATA_POISON_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ECCCFG1_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : CRCPARCTL1 @ 0XFD0700C4</p> - - The maximum number of DFI PHY clock cycles allowed from the assertion of the dfi_rddata_en signal to the assertion of each of - the corresponding bits of the dfi_rddata_valid signal. This corresponds to the DFI timing parameter tphy_rdlat. Refer to PHY - pecification for correct value. This value it only used for detecting read data timeout when DDR4 retry is enabled by CRCPARC - L1.crc_parity_retry_enable=1. Maximum supported value: - 1:1 Frequency mode : DFITMG0.dfi_t_rddata_en + CRCPARCTL1.dfi_t_phy_ - dlat < 'd114 - 1:2 Frequency mode ANDAND DFITMG0.dfi_rddata_use_sdr == 1 : CRCPARCTL1.dfi_t_phy_rdlat < 64 - 1:2 Frequency mo - e ANDAND DFITMG0.dfi_rddata_use_sdr == 0 : DFITMG0.dfi_t_rddata_en + CRCPARCTL1.dfi_t_phy_rdlat < 'd114 Unit: DFI Clocks - PSU_DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT 0x10 - - After a Parity or CRC error is flagged on dfi_alert_n signal, the software has an option to read the mode registers in the DR - M before the hardware begins the retry process - 1: Wait for software to read/write the mode registers before hardware begins - the retry. After software is done with its operations, it will clear the alert interrupt register bit - 0: Hardware can begin - the retry right away after the dfi_alert_n pulse goes away. The value on this register is valid only when retry is enabled (P - RCTRL.crc_parity_retry_enable = 1) If this register is set to 1 and if the software doesn't clear the interrupt register afte - handling the parity/CRC error, then the hardware will not begin the retry process and the system will hang. In the case of P - rity/CRC error, there are two possibilities when the software doesn't reset MR5[4] to 0. - (i) If 'Persistent parity' mode re - ister bit is NOT set: the commands sent during retry and normal operation are executed without parity checking. The value in - he Parity error log register MPR Page 1 is valid. - (ii) If 'Persistent parity' mode register bit is SET: Parity checking is - one for commands sent during retry and normal operation. If multiple errors occur before MR5[4] is cleared, the error log in - PR Page 1 should be treated as 'Don't care'. - PSU_DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW 0x1 - - - 1: Enable command retry mechanism in case of C/A Parity or CRC error - 0: Disable command retry mechanism when C/A Parity o - CRC features are enabled. Note that retry functionality is not supported if burst chop is enabled (MSTR.burstchop = 1) and/o - disable auto-refresh is enabled (RFSHCTL3.dis_auto_refresh = 1) - PSU_DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE 0x0 - - CRC Calculation setting register - 1: CRC includes DM signal - 0: CRC not includes DM signal Present only in designs configur - d to support DDR4. - PSU_DDRC_CRCPARCTL1_CRC_INC_DM 0x0 - - CRC enable Register - 1: Enable generation of CRC - 0: Disable generation of CRC The setting of this register should match th - CRC mode register setting in the DRAM. - PSU_DDRC_CRCPARCTL1_CRC_ENABLE 0x0 - - C/A Parity enable register - 1: Enable generation of C/A parity and detection of C/A parity error - 0: Disable generation of - /A parity and disable detection of C/A parity error If RCD's parity error detection or SDRAM's parity detection is enabled, t - is register should be 1. - PSU_DDRC_CRCPARCTL1_PARITY_ENABLE 0x0 - - CRC Parity Control Register1 - (OFFSET, MASK, VALUE) (0XFD0700C4, 0x3F000391U ,0x10000200U) - RegMask = (DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT_MASK | DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW_MASK | DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE_MASK | DDRC_CRCPARCTL1_CRC_INC_DM_MASK | DDRC_CRCPARCTL1_CRC_ENABLE_MASK | DDRC_CRCPARCTL1_PARITY_ENABLE_MASK | 0 ); - - RegVal = ((0x00000010U << DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT_SHIFT - | 0x00000001U << DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW_SHIFT - | 0x00000000U << DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE_SHIFT - | 0x00000000U << DDRC_CRCPARCTL1_CRC_INC_DM_SHIFT - | 0x00000000U << DDRC_CRCPARCTL1_CRC_ENABLE_SHIFT - | 0x00000000U << DDRC_CRCPARCTL1_PARITY_ENABLE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_CRCPARCTL1_OFFSET ,0x3F000391U ,0x10000200U); - /*############################################################################################################################ */ - - /*Register : CRCPARCTL2 @ 0XFD0700C8</p> - - Value from the DRAM spec indicating the maximum width of the dfi_alert_n pulse when a parity error occurs. Recommended values - - tPAR_ALERT_PW.MAX For configurations with MEMC_FREQ_RATIO=2, program this to tPAR_ALERT_PW.MAX/2 and round up to next inte - er value. Values of 0, 1 and 2 are illegal. This value must be greater than CRCPARCTL2.t_crc_alert_pw_max. - PSU_DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX 0x40 - - Value from the DRAM spec indicating the maximum width of the dfi_alert_n pulse when a CRC error occurs. Recommended values: - - tCRC_ALERT_PW.MAX For configurations with MEMC_FREQ_RATIO=2, program this to tCRC_ALERT_PW.MAX/2 and round up to next integer - value. Values of 0, 1 and 2 are illegal. This value must be less than CRCPARCTL2.t_par_alert_pw_max. - PSU_DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX 0x5 - - Indicates the maximum duration in number of DRAM clock cycles for which a command should be held in the Command Retry FIFO be - ore it is popped out. Every location in the Command Retry FIFO has an associated down counting timer that will use this regis - er as the start value. The down counting starts when a command is loaded into the FIFO. The timer counts down every 4 DRAM cy - les. When the counter reaches zero, the entry is popped from the FIFO. All the counters are frozen, if a C/A Parity or CRC er - or occurs before the counter reaches zero. The counter is reset to 0, after all the commands in the FIFO are retried. Recomme - ded(minimum) values: - Only C/A Parity is enabled. RoundUp((PHY Command Latency(DRAM CLK) + CAL + RDIMM delay + tPAR_ALERT_ON - max + tPAR_UNKNOWN + PHY Alert Latency(DRAM CLK) + board delay) / 4) + 2 - Both C/A Parity and CRC is enabled/ Only CRC is en - bled. RoundUp((PHY Command Latency(DRAM CLK) + CAL + RDIMM delay + WL + 5(BL10)+ tCRC_ALERT.max + PHY Alert Latency(DRAM CLK) - + board delay) / 4) + 2 Note 1: All value (e.g. tPAR_ALERT_ON) should be in terms of DRAM Clock and round up Note 2: Board de - ay(Command/Alert_n) should be considered. Note 3: Use the worst case(longer) value for PHY Latencies/Board delay Note 4: The - ecommended values are minimum value to be set. For mode detail, See 'Calculation of FIFO Depth' section. Max value can be set - to this register is defined below: - MEMC_BURST_LENGTH == 16 Full bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH- - Full bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-3 Half bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_D - PTH-4 Half bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-6 Quarter bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CM - _FIFO_DEPTH-8 Quarter bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-12 - MEMC_BURST_LENGTH != 16 Full bus Mode (C - C=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-1 Full bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-2 Half bus Mo - e (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-2 Half bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-3 Quarte - bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-4 Quarter bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEP - H-6 Values of 0, 1 and 2 are illegal. - PSU_DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4 0x1f - - CRC Parity Control Register2 - (OFFSET, MASK, VALUE) (0XFD0700C8, 0x01FF1F3FU ,0x0040051FU) - RegMask = (DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX_MASK | DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX_MASK | DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4_MASK | 0 ); - - RegVal = ((0x00000040U << DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX_SHIFT - | 0x00000005U << DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX_SHIFT - | 0x0000001FU << DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_CRCPARCTL2_OFFSET ,0x01FF1F3FU ,0x0040051FU); - /*############################################################################################################################ */ - - /*Register : INIT0 @ 0XFD0700D0</p> - - If lower bit is enabled the SDRAM initialization routine is skipped. The upper bit decides what state the controller starts u - in when reset is removed - 00 - SDRAM Intialization routine is run after power-up - 01 - SDRAM Intialization routine is skip - ed after power-up. Controller starts up in Normal Mode - 11 - SDRAM Intialization routine is skipped after power-up. Controll - r starts up in Self-refresh Mode - 10 - SDRAM Intialization routine is run after power-up. Note: The only 2'b00 is supported - or LPDDR4 in this version of the uMCTL2. - PSU_DDRC_INIT0_SKIP_DRAM_INIT 0x0 - - Cycles to wait after driving CKE high to start the SDRAM initialization sequence. Unit: 1024 clocks. DDR2 typically requires - 400 ns delay, requiring this value to be programmed to 2 at all clock speeds. LPDDR2/LPDDR3 typically requires this to be pr - grammed for a delay of 200 us. LPDDR4 typically requires this to be programmed for a delay of 2 us. For configurations with M - MC_FREQ_RATIO=2, program this to JEDEC spec value divided by 2, and round it up to next integer value. - PSU_DDRC_INIT0_POST_CKE_X1024 0x2 - - Cycles to wait after reset before driving CKE high to start the SDRAM initialization sequence. Unit: 1024 clock cycles. DDR2 - pecifications typically require this to be programmed for a delay of >= 200 us. LPDDR2/LPDDR3: tINIT1 of 100 ns (min) LPDDR4: - tINIT3 of 2 ms (min) For configurations with MEMC_FREQ_RATIO=2, program this to JEDEC spec value divided by 2, and round it u - to next integer value. - PSU_DDRC_INIT0_PRE_CKE_X1024 0x106 - - SDRAM Initialization Register 0 - (OFFSET, MASK, VALUE) (0XFD0700D0, 0xC3FF0FFFU ,0x00020106U) - RegMask = (DDRC_INIT0_SKIP_DRAM_INIT_MASK | DDRC_INIT0_POST_CKE_X1024_MASK | DDRC_INIT0_PRE_CKE_X1024_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_INIT0_SKIP_DRAM_INIT_SHIFT - | 0x00000002U << DDRC_INIT0_POST_CKE_X1024_SHIFT - | 0x00000106U << DDRC_INIT0_PRE_CKE_X1024_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_INIT0_OFFSET ,0xC3FF0FFFU ,0x00020106U); - /*############################################################################################################################ */ - - /*Register : INIT1 @ 0XFD0700D4</p> - - Number of cycles to assert SDRAM reset signal during init sequence. This is only present for designs supporting DDR3, DDR4 or - LPDDR4 devices. For use with a DDR PHY, this should be set to a minimum of 1 - PSU_DDRC_INIT1_DRAM_RSTN_X1024 0x2 - - Cycles to wait after completing the SDRAM initialization sequence before starting the dynamic scheduler. Unit: Counts of a gl - bal timer that pulses every 32 clock cycles. There is no known specific requirement for this; it may be set to zero. - PSU_DDRC_INIT1_FINAL_WAIT_X32 0x0 - - Wait period before driving the OCD complete command to SDRAM. Unit: Counts of a global timer that pulses every 32 clock cycle - . There is no known specific requirement for this; it may be set to zero. - PSU_DDRC_INIT1_PRE_OCD_X32 0x0 - - SDRAM Initialization Register 1 - (OFFSET, MASK, VALUE) (0XFD0700D4, 0x01FF7F0FU ,0x00020000U) - RegMask = (DDRC_INIT1_DRAM_RSTN_X1024_MASK | DDRC_INIT1_FINAL_WAIT_X32_MASK | DDRC_INIT1_PRE_OCD_X32_MASK | 0 ); - - RegVal = ((0x00000002U << DDRC_INIT1_DRAM_RSTN_X1024_SHIFT - | 0x00000000U << DDRC_INIT1_FINAL_WAIT_X32_SHIFT - | 0x00000000U << DDRC_INIT1_PRE_OCD_X32_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_INIT1_OFFSET ,0x01FF7F0FU ,0x00020000U); - /*############################################################################################################################ */ - - /*Register : INIT2 @ 0XFD0700D8</p> - - Idle time after the reset command, tINIT4. Present only in designs configured to support LPDDR2. Unit: 32 clock cycles. - PSU_DDRC_INIT2_IDLE_AFTER_RESET_X32 0x23 - - Time to wait after the first CKE high, tINIT2. Present only in designs configured to support LPDDR2/LPDDR3. Unit: 1 clock cyc - e. LPDDR2/LPDDR3 typically requires 5 x tCK delay. - PSU_DDRC_INIT2_MIN_STABLE_CLOCK_X1 0x5 - - SDRAM Initialization Register 2 - (OFFSET, MASK, VALUE) (0XFD0700D8, 0x0000FF0FU ,0x00002305U) - RegMask = (DDRC_INIT2_IDLE_AFTER_RESET_X32_MASK | DDRC_INIT2_MIN_STABLE_CLOCK_X1_MASK | 0 ); - - RegVal = ((0x00000023U << DDRC_INIT2_IDLE_AFTER_RESET_X32_SHIFT - | 0x00000005U << DDRC_INIT2_MIN_STABLE_CLOCK_X1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_INIT2_OFFSET ,0x0000FF0FU ,0x00002305U); - /*############################################################################################################################ */ - - /*Register : INIT3 @ 0XFD0700DC</p> - - DDR2: Value to write to MR register. Bit 8 is for DLL and the setting here is ignored. The uMCTL2 sets this bit appropriately - DDR3/DDR4: Value loaded into MR0 register. mDDR: Value to write to MR register. LPDDR2/LPDDR3/LPDDR4 - Value to write to MR1 - register - PSU_DDRC_INIT3_MR 0x930 - - DDR2: Value to write to EMR register. Bits 9:7 are for OCD and the setting in this register is ignored. The uMCTL2 sets those - bits appropriately. DDR3/DDR4: Value to write to MR1 register Set bit 7 to 0. If PHY-evaluation mode training is enabled, thi - bit is set appropriately by the uMCTL2 during write leveling. mDDR: Value to write to EMR register. LPDDR2/LPDDR3/LPDDR4 - V - lue to write to MR2 register - PSU_DDRC_INIT3_EMR 0x301 - - SDRAM Initialization Register 3 - (OFFSET, MASK, VALUE) (0XFD0700DC, 0xFFFFFFFFU ,0x09300301U) - RegMask = (DDRC_INIT3_MR_MASK | DDRC_INIT3_EMR_MASK | 0 ); - - RegVal = ((0x00000930U << DDRC_INIT3_MR_SHIFT - | 0x00000301U << DDRC_INIT3_EMR_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_INIT3_OFFSET ,0xFFFFFFFFU ,0x09300301U); - /*############################################################################################################################ */ - - /*Register : INIT4 @ 0XFD0700E0</p> - - DDR2: Value to write to EMR2 register. DDR3/DDR4: Value to write to MR2 register LPDDR2/LPDDR3/LPDDR4: Value to write to MR3 - egister mDDR: Unused - PSU_DDRC_INIT4_EMR2 0x20 - - DDR2: Value to write to EMR3 register. DDR3/DDR4: Value to write to MR3 register mDDR/LPDDR2/LPDDR3: Unused LPDDR4: Value to - rite to MR13 register - PSU_DDRC_INIT4_EMR3 0x200 - - SDRAM Initialization Register 4 - (OFFSET, MASK, VALUE) (0XFD0700E0, 0xFFFFFFFFU ,0x00200200U) - RegMask = (DDRC_INIT4_EMR2_MASK | DDRC_INIT4_EMR3_MASK | 0 ); - - RegVal = ((0x00000020U << DDRC_INIT4_EMR2_SHIFT - | 0x00000200U << DDRC_INIT4_EMR3_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_INIT4_OFFSET ,0xFFFFFFFFU ,0x00200200U); - /*############################################################################################################################ */ - - /*Register : INIT5 @ 0XFD0700E4</p> - - ZQ initial calibration, tZQINIT. Present only in designs configured to support DDR3 or DDR4 or LPDDR2/LPDDR3. Unit: 32 clock - ycles. DDR3 typically requires 512 clocks. DDR4 requires 1024 clocks. LPDDR2/LPDDR3 requires 1 us. - PSU_DDRC_INIT5_DEV_ZQINIT_X32 0x21 - - Maximum duration of the auto initialization, tINIT5. Present only in designs configured to support LPDDR2/LPDDR3. LPDDR2/LPDD - 3 typically requires 10 us. - PSU_DDRC_INIT5_MAX_AUTO_INIT_X1024 0x4 - - SDRAM Initialization Register 5 - (OFFSET, MASK, VALUE) (0XFD0700E4, 0x00FF03FFU ,0x00210004U) - RegMask = (DDRC_INIT5_DEV_ZQINIT_X32_MASK | DDRC_INIT5_MAX_AUTO_INIT_X1024_MASK | 0 ); - - RegVal = ((0x00000021U << DDRC_INIT5_DEV_ZQINIT_X32_SHIFT - | 0x00000004U << DDRC_INIT5_MAX_AUTO_INIT_X1024_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_INIT5_OFFSET ,0x00FF03FFU ,0x00210004U); - /*############################################################################################################################ */ - - /*Register : INIT6 @ 0XFD0700E8</p> - - DDR4- Value to be loaded into SDRAM MR4 registers. Used in DDR4 designs only. - PSU_DDRC_INIT6_MR4 0x0 - - DDR4- Value to be loaded into SDRAM MR5 registers. Used in DDR4 designs only. - PSU_DDRC_INIT6_MR5 0x6c0 - - SDRAM Initialization Register 6 - (OFFSET, MASK, VALUE) (0XFD0700E8, 0xFFFFFFFFU ,0x000006C0U) - RegMask = (DDRC_INIT6_MR4_MASK | DDRC_INIT6_MR5_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_INIT6_MR4_SHIFT - | 0x000006C0U << DDRC_INIT6_MR5_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_INIT6_OFFSET ,0xFFFFFFFFU ,0x000006C0U); - /*############################################################################################################################ */ - - /*Register : INIT7 @ 0XFD0700EC</p> - - DDR4- Value to be loaded into SDRAM MR6 registers. Used in DDR4 designs only. - PSU_DDRC_INIT7_MR6 0x819 - - SDRAM Initialization Register 7 - (OFFSET, MASK, VALUE) (0XFD0700EC, 0xFFFF0000U ,0x08190000U) - RegMask = (DDRC_INIT7_MR6_MASK | 0 ); - - RegVal = ((0x00000819U << DDRC_INIT7_MR6_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_INIT7_OFFSET ,0xFFFF0000U ,0x08190000U); - /*############################################################################################################################ */ - - /*Register : DIMMCTL @ 0XFD0700F0</p> - - Disabling Address Mirroring for BG bits. When this is set to 1, BG0 and BG1 are NOT swapped even if Address Mirroring is enab - ed. This will be required for DDR4 DIMMs with x16 devices. - 1 - BG0 and BG1 are NOT swapped. - 0 - BG0 and BG1 are swapped i - address mirroring is enabled. - PSU_DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING 0x0 - - Enable for BG1 bit of MRS command. BG1 bit of the mode register address is specified as RFU (Reserved for Future Use) and mus - be programmed to 0 during MRS. In case where DRAMs which do not have BG1 are attached and both the CA parity and the Output - nversion are enabled, this must be set to 0, so that the calculation of CA parity will not include BG1 bit. Note: This has no - effect on the address of any other memory accesses, or of software-driven mode register accesses. If address mirroring is ena - led, this is applied to BG1 of even ranks and BG0 of odd ranks. - 1 - Enabled - 0 - Disabled - PSU_DDRC_DIMMCTL_MRS_BG1_EN 0x1 - - Enable for A17 bit of MRS command. A17 bit of the mode register address is specified as RFU (Reserved for Future Use) and mus - be programmed to 0 during MRS. In case where DRAMs which do not have A17 are attached and the Output Inversion are enabled, - his must be set to 0, so that the calculation of CA parity will not include A17 bit. Note: This has no effect on the address - f any other memory accesses, or of software-driven mode register accesses. - 1 - Enabled - 0 - Disabled - PSU_DDRC_DIMMCTL_MRS_A17_EN 0x0 - - Output Inversion Enable (for DDR4 RDIMM implementations only). DDR4 RDIMM implements the Output Inversion feature by default, - which means that the following address, bank address and bank group bits of B-side DRAMs are inverted: A3-A9, A11, A13, A17, - A0-BA1, BG0-BG1. Setting this bit ensures that, for mode register accesses generated by the uMCTL2 during the automatic initi - lization routine and enabling of a particular DDR4 feature, separate A-side and B-side mode register accesses are generated. - or B-side mode register accesses, these bits are inverted within the uMCTL2 to compensate for this RDIMM inversion. Note: Thi - has no effect on the address of any other memory accesses, or of software-driven mode register accesses. - 1 - Implement out - ut inversion for B-side DRAMs. - 0 - Do not implement output inversion for B-side DRAMs. - PSU_DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN 0x0 - - Address Mirroring Enable (for multi-rank UDIMM implementations and multi-rank DDR4 RDIMM implementations). Some UDIMMs and DD - 4 RDIMMs implement address mirroring for odd ranks, which means that the following address, bank address and bank group bits - re swapped: (A3, A4), (A5, A6), (A7, A8), (BA0, BA1) and also (A11, A13), (BG0, BG1) for the DDR4. Setting this bit ensures t - at, for mode register accesses during the automatic initialization routine, these bits are swapped within the uMCTL2 to compe - sate for this UDIMM/RDIMM swapping. In addition to the automatic initialization routine, in case of DDR4 UDIMM/RDIMM, they ar - swapped during the automatic MRS access to enable/disable of a particular DDR4 feature. Note: This has no effect on the addr - ss of any other memory accesses, or of software-driven mode register accesses. This is not supported for mDDR, LPDDR2, LPDDR3 - or LPDDR4 SDRAMs. Note: In case of x16 DDR4 DIMMs, BG1 output of MRS for the odd ranks is same as BG0 because BG1 is invalid, - hence dimm_dis_bg_mirroring register must be set to 1. - 1 - For odd ranks, implement address mirroring for MRS commands to d - ring initialization and for any automatic DDR4 MRS commands (to be used if UDIMM/RDIMM implements address mirroring) - 0 - Do - not implement address mirroring - PSU_DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN 0x0 - - Staggering enable for multi-rank accesses (for multi-rank UDIMM and RDIMM implementations only). This is not supported for mD - R, LPDDR2, LPDDR3 or LPDDR4 SDRAMs. Note: Even if this bit is set it does not take care of software driven MR commands (via M - CTRL0/MRCTRL1), where software is responsible to send them to seperate ranks as appropriate. - 1 - (DDR4) Send MRS commands t - each ranks seperately - 1 - (non-DDR4) Send all commands to even and odd ranks seperately - 0 - Do not stagger accesses - PSU_DDRC_DIMMCTL_DIMM_STAGGER_CS_EN 0x0 - - DIMM Control Register - (OFFSET, MASK, VALUE) (0XFD0700F0, 0x0000003FU ,0x00000010U) - RegMask = (DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING_MASK | DDRC_DIMMCTL_MRS_BG1_EN_MASK | DDRC_DIMMCTL_MRS_A17_EN_MASK | DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN_MASK | DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN_MASK | DDRC_DIMMCTL_DIMM_STAGGER_CS_EN_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING_SHIFT - | 0x00000001U << DDRC_DIMMCTL_MRS_BG1_EN_SHIFT - | 0x00000000U << DDRC_DIMMCTL_MRS_A17_EN_SHIFT - | 0x00000000U << DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN_SHIFT - | 0x00000000U << DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN_SHIFT - | 0x00000000U << DDRC_DIMMCTL_DIMM_STAGGER_CS_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DIMMCTL_OFFSET ,0x0000003FU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : RANKCTL @ 0XFD0700F4</p> - - Only present for multi-rank configurations. Indicates the number of clocks of gap in data responses when performing consecuti - e writes to different ranks. This is used to switch the delays in the PHY to match the rank requirements. This value should c - nsider both PHY requirement and ODT requirement. - PHY requirement: tphy_wrcsgap + 1 (see PHY databook for value of tphy_wrcs - ap) If CRC feature is enabled, should be increased by 1. If write preamble is set to 2tCK(DDR4/LPDDR4 only), should be increa - ed by 1. If write postamble is set to 1.5tCK(LPDDR4 only), should be increased by 1. - ODT requirement: The value programmed - n this register takes care of the ODT switch off timing requirement when switching ranks during writes. For LPDDR4, the requi - ement is ODTLoff - ODTLon - BL/2 + 1 For configurations with MEMC_FREQ_RATIO=1, program this to the larger of PHY requirement - or ODT requirement. For configurations with MEMC_FREQ_RATIO=2, program this to the larger value divided by two and round it u - to the next integer. - PSU_DDRC_RANKCTL_DIFF_RANK_WR_GAP 0x6 - - Only present for multi-rank configurations. Indicates the number of clocks of gap in data responses when performing consecuti - e reads to different ranks. This is used to switch the delays in the PHY to match the rank requirements. This value should co - sider both PHY requirement and ODT requirement. - PHY requirement: tphy_rdcsgap + 1 (see PHY databook for value of tphy_rdcsg - p) If read preamble is set to 2tCK(DDR4/LPDDR4 only), should be increased by 1. If read postamble is set to 1.5tCK(LPDDR4 onl - ), should be increased by 1. - ODT requirement: The value programmed in this register takes care of the ODT switch off timing - requirement when switching ranks during reads. For configurations with MEMC_FREQ_RATIO=1, program this to the larger of PHY r - quirement or ODT requirement. For configurations with MEMC_FREQ_RATIO=2, program this to the larger value divided by two and - ound it up to the next integer. - PSU_DDRC_RANKCTL_DIFF_RANK_RD_GAP 0x6 - - Only present for multi-rank configurations. Background: Reads to the same rank can be performed back-to-back. Reads to differ - nt ranks require additional gap dictated by the register RANKCTL.diff_rank_rd_gap. This is to avoid possible data bus content - on as well as to give PHY enough time to switch the delay when changing ranks. The uMCTL2 arbitrates for bus access on a cycl - -by-cycle basis; therefore after a read is scheduled, there are few clock cycles (determined by the value on RANKCTL.diff_ran - _rd_gap register) in which only reads from the same rank are eligible to be scheduled. This prevents reads from other ranks f - om having fair access to the data bus. This parameter represents the maximum number of reads that can be scheduled consecutiv - ly to the same rank. After this number is reached, a delay equal to RANKCTL.diff_rank_rd_gap is inserted by the scheduler to - llow all ranks a fair opportunity to be scheduled. Higher numbers increase bandwidth utilization, lower numbers increase fair - ess. This feature can be DISABLED by setting this register to 0. When set to 0, the Controller will stay on the same rank as - ong as commands are available for it. Minimum programmable value is 0 (feature disabled) and maximum programmable value is 0x - . FOR PERFORMANCE ONLY. - PSU_DDRC_RANKCTL_MAX_RANK_RD 0xf - - Rank Control Register - (OFFSET, MASK, VALUE) (0XFD0700F4, 0x00000FFFU ,0x0000066FU) - RegMask = (DDRC_RANKCTL_DIFF_RANK_WR_GAP_MASK | DDRC_RANKCTL_DIFF_RANK_RD_GAP_MASK | DDRC_RANKCTL_MAX_RANK_RD_MASK | 0 ); - - RegVal = ((0x00000006U << DDRC_RANKCTL_DIFF_RANK_WR_GAP_SHIFT - | 0x00000006U << DDRC_RANKCTL_DIFF_RANK_RD_GAP_SHIFT - | 0x0000000FU << DDRC_RANKCTL_MAX_RANK_RD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_RANKCTL_OFFSET ,0x00000FFFU ,0x0000066FU); - /*############################################################################################################################ */ - - /*Register : DRAMTMG0 @ 0XFD070100</p> - - Minimum time between write and precharge to same bank. Unit: Clocks Specifications: WL + BL/2 + tWR = approximately 8 cycles - 15 ns = 14 clocks @400MHz and less for lower frequencies where: - WL = write latency - BL = burst length. This must match th - value programmed in the BL bit of the mode register to the SDRAM. BST (burst terminate) is not supported at present. - tWR = - Write recovery time. This comes directly from the SDRAM specification. Add one extra cycle for LPDDR2/LPDDR3/LPDDR4 for this - arameter. For configurations with MEMC_FREQ_RATIO=2, 1T mode, divide the above value by 2. No rounding up. For configurations - with MEMC_FREQ_RATIO=2, 2T mode or LPDDR4 mode, divide the above value by 2 and round it up to the next integer value. - PSU_DDRC_DRAMTMG0_WR2PRE 0x11 - - tFAW Valid only when 8 or more banks(or banks x bank groups) are present. In 8-bank design, at most 4 banks must be activated - in a rolling window of tFAW cycles. For configurations with MEMC_FREQ_RATIO=2, program this to (tFAW/2) and round up to next - nteger value. In a 4-bank design, set this register to 0x1 independent of the MEMC_FREQ_RATIO configuration. Unit: Clocks - PSU_DDRC_DRAMTMG0_T_FAW 0x11 - - tRAS(max): Maximum time between activate and precharge to same bank. This is the maximum time that a page can be kept open Mi - imum value of this register is 1. Zero is invalid. For configurations with MEMC_FREQ_RATIO=2, program this to (tRAS(max)-1)/2 - No rounding up. Unit: Multiples of 1024 clocks. - PSU_DDRC_DRAMTMG0_T_RAS_MAX 0x24 - - tRAS(min): Minimum time between activate and precharge to the same bank. For configurations with MEMC_FREQ_RATIO=2, 1T mode, - rogram this to tRAS(min)/2. No rounding up. For configurations with MEMC_FREQ_RATIO=2, 2T mode or LPDDR4 mode, program this t - (tRAS(min)/2) and round it up to the next integer value. Unit: Clocks - PSU_DDRC_DRAMTMG0_T_RAS_MIN 0x12 - - SDRAM Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD070100, 0x7F3F7F3FU ,0x11112412U) - RegMask = (DDRC_DRAMTMG0_WR2PRE_MASK | DDRC_DRAMTMG0_T_FAW_MASK | DDRC_DRAMTMG0_T_RAS_MAX_MASK | DDRC_DRAMTMG0_T_RAS_MIN_MASK | 0 ); - - RegVal = ((0x00000011U << DDRC_DRAMTMG0_WR2PRE_SHIFT - | 0x00000011U << DDRC_DRAMTMG0_T_FAW_SHIFT - | 0x00000024U << DDRC_DRAMTMG0_T_RAS_MAX_SHIFT - | 0x00000012U << DDRC_DRAMTMG0_T_RAS_MIN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG0_OFFSET ,0x7F3F7F3FU ,0x11112412U); - /*############################################################################################################################ */ - - /*Register : DRAMTMG1 @ 0XFD070104</p> - - tXP: Minimum time after power-down exit to any operation. For DDR3, this should be programmed to tXPDLL if slow powerdown exi - is selected in MR0[12]. If C/A parity for DDR4 is used, set to (tXP+PL) instead. For configurations with MEMC_FREQ_RATIO=2, - rogram this to (tXP/2) and round it up to the next integer value. Units: Clocks - PSU_DDRC_DRAMTMG1_T_XP 0x4 - - tRTP: Minimum time from read to precharge of same bank. - DDR2: tAL + BL/2 + max(tRTP, 2) - 2 - DDR3: tAL + max (tRTP, 4) - D - R4: Max of following two equations: tAL + max (tRTP, 4) or, RL + BL/2 - tRP. - mDDR: BL/2 - LPDDR2: Depends on if it's LPDDR2 - S2 or LPDDR2-S4: LPDDR2-S2: BL/2 + tRTP - 1. LPDDR2-S4: BL/2 + max(tRTP,2) - 2. - LPDDR3: BL/2 + max(tRTP,4) - 4 - LPDDR4: BL - 2 + max(tRTP,8) - 8 For configurations with MEMC_FREQ_RATIO=2, 1T mode, divide the above value by 2. No rounding up. For conf - gurations with MEMC_FREQ_RATIO=2, 2T mode or LPDDR4 mode, divide the above value by 2 and round it up to the next integer val - e. Unit: Clocks. - PSU_DDRC_DRAMTMG1_RD2PRE 0x4 - - tRC: Minimum time between activates to same bank. For configurations with MEMC_FREQ_RATIO=2, program this to (tRC/2) and roun - up to next integer value. Unit: Clocks. - PSU_DDRC_DRAMTMG1_T_RC 0x1a - - SDRAM Timing Register 1 - (OFFSET, MASK, VALUE) (0XFD070104, 0x001F1F7FU ,0x0004041AU) - RegMask = (DDRC_DRAMTMG1_T_XP_MASK | DDRC_DRAMTMG1_RD2PRE_MASK | DDRC_DRAMTMG1_T_RC_MASK | 0 ); - - RegVal = ((0x00000004U << DDRC_DRAMTMG1_T_XP_SHIFT - | 0x00000004U << DDRC_DRAMTMG1_RD2PRE_SHIFT - | 0x0000001AU << DDRC_DRAMTMG1_T_RC_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG1_OFFSET ,0x001F1F7FU ,0x0004041AU); - /*############################################################################################################################ */ - - /*Register : DRAMTMG2 @ 0XFD070108</p> - - Set to WL Time from write command to write data on SDRAM interface. This must be set to WL. For mDDR, it should normally be s - t to 1. Note that, depending on the PHY, if using RDIMM, it may be necessary to use a value of WL + 1 to compensate for the e - tra cycle of latency through the RDIMM For configurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above - equation by 2, and round it up to next integer. This register field is not required for DDR2 and DDR3 (except if MEMC_TRAININ - is set), as the DFI read and write latencies defined in DFITMG0 and DFITMG1 are sufficient for those protocols Unit: clocks - PSU_DDRC_DRAMTMG2_WRITE_LATENCY 0x7 - - Set to RL Time from read command to read data on SDRAM interface. This must be set to RL. Note that, depending on the PHY, if - using RDIMM, it mat be necessary to use a value of RL + 1 to compensate for the extra cycle of latency through the RDIMM For - onfigurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next inte - er. This register field is not required for DDR2 and DDR3 (except if MEMC_TRAINING is set), as the DFI read and write latenci - s defined in DFITMG0 and DFITMG1 are sufficient for those protocols Unit: clocks - PSU_DDRC_DRAMTMG2_READ_LATENCY 0x8 - - DDR2/3/mDDR: RL + BL/2 + 2 - WL DDR4: RL + BL/2 + 1 + WR_PREAMBLE - WL LPDDR2/LPDDR3: RL + BL/2 + RU(tDQSCKmax/tCK) + 1 - WL - PDDR4(DQ ODT is Disabled): RL + BL/2 + RU(tDQSCKmax/tCK) + WR_PREAMBLE + RD_POSTAMBLE - WL LPDDR4(DQ ODT is Enabled) : RL + B - /2 + RU(tDQSCKmax/tCK) + RD_POSTAMBLE - ODTLon - RU(tODTon(min)/tCK) Minimum time from read command to write command. Include - time for bus turnaround and all per-bank, per-rank, and global constraints. Unit: Clocks. Where: - WL = write latency - BL = - urst length. This must match the value programmed in the BL bit of the mode register to the SDRAM - RL = read latency = CAS l - tency - WR_PREAMBLE = write preamble. This is unique to DDR4 and LPDDR4. - RD_POSTAMBLE = read postamble. This is unique to L - DDR4. For LPDDR2/LPDDR3/LPDDR4, if derating is enabled (DERATEEN.derate_enable=1), derated tDQSCKmax should be used. For conf - gurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next integer. - PSU_DDRC_DRAMTMG2_RD2WR 0x6 - - DDR4: CWL + PL + BL/2 + tWTR_L Others: CWL + BL/2 + tWTR In DDR4, minimum time from write command to read command for same ba - k group. In others, minimum time from write command to read command. Includes time for bus turnaround, recovery times, and al - per-bank, per-rank, and global constraints. Unit: Clocks. Where: - CWL = CAS write latency - PL = Parity latency - BL = burs - length. This must match the value programmed in the BL bit of the mode register to the SDRAM - tWTR_L = internal write to re - d command delay for same bank group. This comes directly from the SDRAM specification. - tWTR = internal write to read comman - delay. This comes directly from the SDRAM specification. Add one extra cycle for LPDDR2/LPDDR3/LPDDR4 operation. For configu - ations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next integer. - PSU_DDRC_DRAMTMG2_WR2RD 0xe - - SDRAM Timing Register 2 - (OFFSET, MASK, VALUE) (0XFD070108, 0x3F3F3F3FU ,0x0708060EU) - RegMask = (DDRC_DRAMTMG2_WRITE_LATENCY_MASK | DDRC_DRAMTMG2_READ_LATENCY_MASK | DDRC_DRAMTMG2_RD2WR_MASK | DDRC_DRAMTMG2_WR2RD_MASK | 0 ); - - RegVal = ((0x00000007U << DDRC_DRAMTMG2_WRITE_LATENCY_SHIFT - | 0x00000008U << DDRC_DRAMTMG2_READ_LATENCY_SHIFT - | 0x00000006U << DDRC_DRAMTMG2_RD2WR_SHIFT - | 0x0000000EU << DDRC_DRAMTMG2_WR2RD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG2_OFFSET ,0x3F3F3F3FU ,0x0708060EU); - /*############################################################################################################################ */ - - /*Register : DRAMTMG3 @ 0XFD07010C</p> - - Time to wait after a mode register write or read (MRW or MRR). Present only in designs configured to support LPDDR2, LPDDR3 o - LPDDR4. LPDDR2 typically requires value of 5. LPDDR3 typically requires value of 10. LPDDR4: Set this to the larger of tMRW - nd tMRWCKEL. For LPDDR2, this register is used for the time from a MRW/MRR to all other commands. For LDPDR3, this register i - used for the time from a MRW/MRR to a MRW/MRR. - PSU_DDRC_DRAMTMG3_T_MRW 0x5 - - tMRD: Cycles to wait after a mode register write or read. Depending on the connected SDRAM, tMRD represents: DDR2/mDDR: Time - rom MRS to any command DDR3/4: Time from MRS to MRS command LPDDR2: not used LPDDR3/4: Time from MRS to non-MRS command For c - nfigurations with MEMC_FREQ_RATIO=2, program this to (tMRD/2) and round it up to the next integer value. If C/A parity for DD - 4 is used, set to tMRD_PAR(tMOD+PL) instead. - PSU_DDRC_DRAMTMG3_T_MRD 0x4 - - tMOD: Parameter used only in DDR3 and DDR4. Cycles between load mode command and following non-load mode command. If C/A pari - y for DDR4 is used, set to tMOD_PAR(tMOD+PL) instead. Set to tMOD if MEMC_FREQ_RATIO=1, or tMOD/2 (rounded up to next integer - if MEMC_FREQ_RATIO=2. Note that if using RDIMM, depending on the PHY, it may be necessary to use a value of tMOD + 1 or (tMO - + 1)/2 to compensate for the extra cycle of latency applied to mode register writes by the RDIMM chip. - PSU_DDRC_DRAMTMG3_T_MOD 0xc - - SDRAM Timing Register 3 - (OFFSET, MASK, VALUE) (0XFD07010C, 0x3FF3F3FFU ,0x0050400CU) - RegMask = (DDRC_DRAMTMG3_T_MRW_MASK | DDRC_DRAMTMG3_T_MRD_MASK | DDRC_DRAMTMG3_T_MOD_MASK | 0 ); - - RegVal = ((0x00000005U << DDRC_DRAMTMG3_T_MRW_SHIFT - | 0x00000004U << DDRC_DRAMTMG3_T_MRD_SHIFT - | 0x0000000CU << DDRC_DRAMTMG3_T_MOD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG3_OFFSET ,0x3FF3F3FFU ,0x0050400CU); - /*############################################################################################################################ */ - - /*Register : DRAMTMG4 @ 0XFD070110</p> - - tRCD - tAL: Minimum time from activate to read or write command to same bank. For configurations with MEMC_FREQ_RATIO=2, prog - am this to ((tRCD - tAL)/2) and round it up to the next integer value. Minimum value allowed for this register is 1, which im - lies minimum (tRCD - tAL) value to be 2 in configurations with MEMC_FREQ_RATIO=2. Unit: Clocks. - PSU_DDRC_DRAMTMG4_T_RCD 0x8 - - DDR4: tCCD_L: This is the minimum time between two reads or two writes for same bank group. Others: tCCD: This is the minimum - time between two reads or two writes. For configurations with MEMC_FREQ_RATIO=2, program this to (tCCD_L/2 or tCCD/2) and rou - d it up to the next integer value. Unit: clocks. - PSU_DDRC_DRAMTMG4_T_CCD 0x3 - - DDR4: tRRD_L: Minimum time between activates from bank 'a' to bank 'b' for same bank group. Others: tRRD: Minimum time betwee - activates from bank 'a' to bank 'b'For configurations with MEMC_FREQ_RATIO=2, program this to (tRRD_L/2 or tRRD/2) and round - it up to the next integer value. Unit: Clocks. - PSU_DDRC_DRAMTMG4_T_RRD 0x3 - - tRP: Minimum time from precharge to activate of same bank. For MEMC_FREQ_RATIO=1 configurations, t_rp should be set to RoundU - (tRP/tCK). For MEMC_FREQ_RATIO=2 configurations, t_rp should be set to RoundDown(RoundUp(tRP/tCK)/2) + 1. For MEMC_FREQ_RATIO - 2 configurations in LPDDR4, t_rp should be set to RoundUp(RoundUp(tRP/tCK)/2). Unit: Clocks. - PSU_DDRC_DRAMTMG4_T_RP 0x9 - - SDRAM Timing Register 4 - (OFFSET, MASK, VALUE) (0XFD070110, 0x1F0F0F1FU ,0x08030309U) - RegMask = (DDRC_DRAMTMG4_T_RCD_MASK | DDRC_DRAMTMG4_T_CCD_MASK | DDRC_DRAMTMG4_T_RRD_MASK | DDRC_DRAMTMG4_T_RP_MASK | 0 ); - - RegVal = ((0x00000008U << DDRC_DRAMTMG4_T_RCD_SHIFT - | 0x00000003U << DDRC_DRAMTMG4_T_CCD_SHIFT - | 0x00000003U << DDRC_DRAMTMG4_T_RRD_SHIFT - | 0x00000009U << DDRC_DRAMTMG4_T_RP_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG4_OFFSET ,0x1F0F0F1FU ,0x08030309U); - /*############################################################################################################################ */ - - /*Register : DRAMTMG5 @ 0XFD070114</p> - - This is the time before Self Refresh Exit that CK is maintained as a valid clock before issuing SRX. Specifies the clock stab - e time before SRX. Recommended settings: - mDDR: 1 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEH - DDR2: 1 - DDR3: tCKSRX - DDR4: - tCKSRX For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it up to next in - eger. - PSU_DDRC_DRAMTMG5_T_CKSRX 0x6 - - This is the time after Self Refresh Down Entry that CK is maintained as a valid clock. Specifies the clock disable delay afte - SRE. Recommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEL - DDR2: 1 - DDR3: max (10 ns, 5 tCK) - DDR4: - ax (10 ns, 5 tCK) For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it up - to next integer. - PSU_DDRC_DRAMTMG5_T_CKSRE 0x6 - - Minimum CKE low width for Self refresh or Self refresh power down entry to exit timing in memory clock cycles. Recommended se - tings: - mDDR: tRFC - LPDDR2: tCKESR - LPDDR3: tCKESR - LPDDR4: max(tCKELPD, tSR) - DDR2: tCKE - DDR3: tCKE + 1 - DDR4: tCKE - 1 For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it up to next intege - . - PSU_DDRC_DRAMTMG5_T_CKESR 0x4 - - Minimum number of cycles of CKE HIGH/LOW during power-down and self refresh. - LPDDR2/LPDDR3 mode: Set this to the larger of - CKE or tCKESR - LPDDR4 mode: Set this to the larger of tCKE, tCKELPD or tSR. - Non-LPDDR2/non-LPDDR3/non-LPDDR4 designs: Set - his to tCKE value. For configurations with MEMC_FREQ_RATIO=2, program this to (value described above)/2 and round it up to th - next integer value. Unit: Clocks. - PSU_DDRC_DRAMTMG5_T_CKE 0x3 - - SDRAM Timing Register 5 - (OFFSET, MASK, VALUE) (0XFD070114, 0x0F0F3F1FU ,0x06060403U) - RegMask = (DDRC_DRAMTMG5_T_CKSRX_MASK | DDRC_DRAMTMG5_T_CKSRE_MASK | DDRC_DRAMTMG5_T_CKESR_MASK | DDRC_DRAMTMG5_T_CKE_MASK | 0 ); - - RegVal = ((0x00000006U << DDRC_DRAMTMG5_T_CKSRX_SHIFT - | 0x00000006U << DDRC_DRAMTMG5_T_CKSRE_SHIFT - | 0x00000004U << DDRC_DRAMTMG5_T_CKESR_SHIFT - | 0x00000003U << DDRC_DRAMTMG5_T_CKE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG5_OFFSET ,0x0F0F3F1FU ,0x06060403U); - /*############################################################################################################################ */ - - /*Register : DRAMTMG6 @ 0XFD070118</p> - - This is the time after Deep Power Down Entry that CK is maintained as a valid clock. Specifies the clock disable delay after - PDE. Recommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 For configurations with MEMC_FREQ_RATIO=2, program this to recom - ended value divided by two and round it up to next integer. This is only present for designs supporting mDDR or LPDDR2/LPDDR3 - devices. - PSU_DDRC_DRAMTMG6_T_CKDPDE 0x1 - - This is the time before Deep Power Down Exit that CK is maintained as a valid clock before issuing DPDX. Specifies the clock - table time before DPDX. Recommended settings: - mDDR: 1 - LPDDR2: 2 - LPDDR3: 2 For configurations with MEMC_FREQ_RATIO=2, pr - gram this to recommended value divided by two and round it up to next integer. This is only present for designs supporting mD - R or LPDDR2 devices. - PSU_DDRC_DRAMTMG6_T_CKDPDX 0x1 - - This is the time before Clock Stop Exit that CK is maintained as a valid clock before issuing Clock Stop Exit. Specifies the - lock stable time before next command after Clock Stop Exit. Recommended settings: - mDDR: 1 - LPDDR2: tXP + 2 - LPDDR3: tXP + - 2 - LPDDR4: tXP + 2 For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it - p to next integer. This is only present for designs supporting mDDR or LPDDR2/LPDDR3/LPDDR4 devices. - PSU_DDRC_DRAMTMG6_T_CKCSX 0x4 - - SDRAM Timing Register 6 - (OFFSET, MASK, VALUE) (0XFD070118, 0x0F0F000FU ,0x01010004U) - RegMask = (DDRC_DRAMTMG6_T_CKDPDE_MASK | DDRC_DRAMTMG6_T_CKDPDX_MASK | DDRC_DRAMTMG6_T_CKCSX_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_DRAMTMG6_T_CKDPDE_SHIFT - | 0x00000001U << DDRC_DRAMTMG6_T_CKDPDX_SHIFT - | 0x00000004U << DDRC_DRAMTMG6_T_CKCSX_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG6_OFFSET ,0x0F0F000FU ,0x01010004U); - /*############################################################################################################################ */ - - /*Register : DRAMTMG7 @ 0XFD07011C</p> - - This is the time after Power Down Entry that CK is maintained as a valid clock. Specifies the clock disable delay after PDE. - ecommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEL For configurations with MEMC_FREQ_RATIO=2, program t - is to recommended value divided by two and round it up to next integer. This is only present for designs supporting mDDR or L - DDR2/LPDDR3/LPDDR4 devices. - PSU_DDRC_DRAMTMG7_T_CKPDE 0x6 - - This is the time before Power Down Exit that CK is maintained as a valid clock before issuing PDX. Specifies the clock stable - time before PDX. Recommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: 2 For configurations with MEMC_FREQ_RATIO= - , program this to recommended value divided by two and round it up to next integer. This is only present for designs supporti - g mDDR or LPDDR2/LPDDR3/LPDDR4 devices. - PSU_DDRC_DRAMTMG7_T_CKPDX 0x6 - - SDRAM Timing Register 7 - (OFFSET, MASK, VALUE) (0XFD07011C, 0x00000F0FU ,0x00000606U) - RegMask = (DDRC_DRAMTMG7_T_CKPDE_MASK | DDRC_DRAMTMG7_T_CKPDX_MASK | 0 ); - - RegVal = ((0x00000006U << DDRC_DRAMTMG7_T_CKPDE_SHIFT - | 0x00000006U << DDRC_DRAMTMG7_T_CKPDX_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG7_OFFSET ,0x00000F0FU ,0x00000606U); - /*############################################################################################################################ */ - - /*Register : DRAMTMG8 @ 0XFD070120</p> - - tXS_FAST: Exit Self Refresh to ZQCL, ZQCS and MRS (only CL, WR, RTP and Geardown mode). For configurations with MEMC_FREQ_RAT - O=2, program this to the above value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: Thi - is applicable to only ZQCL/ZQCS commands. Note: Ensure this is less than or equal to t_xs_x32. - PSU_DDRC_DRAMTMG8_T_XS_FAST_X32 0x4 - - tXS_ABORT: Exit Self Refresh to commands not requiring a locked DLL in Self Refresh Abort. For configurations with MEMC_FREQ_ - ATIO=2, program this to the above value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: - nsure this is less than or equal to t_xs_x32. - PSU_DDRC_DRAMTMG8_T_XS_ABORT_X32 0x4 - - tXSDLL: Exit Self Refresh to commands requiring a locked DLL. For configurations with MEMC_FREQ_RATIO=2, program this to the - bove value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: Used only for DDR2, DDR3 and - DR4 SDRAMs. - PSU_DDRC_DRAMTMG8_T_XS_DLL_X32 0xd - - tXS: Exit Self Refresh to commands not requiring a locked DLL. For configurations with MEMC_FREQ_RATIO=2, program this to the - above value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: Used only for DDR2, DDR3 and - DDR4 SDRAMs. - PSU_DDRC_DRAMTMG8_T_XS_X32 0x6 - - SDRAM Timing Register 8 - (OFFSET, MASK, VALUE) (0XFD070120, 0x7F7F7F7FU ,0x04040D06U) - RegMask = (DDRC_DRAMTMG8_T_XS_FAST_X32_MASK | DDRC_DRAMTMG8_T_XS_ABORT_X32_MASK | DDRC_DRAMTMG8_T_XS_DLL_X32_MASK | DDRC_DRAMTMG8_T_XS_X32_MASK | 0 ); - - RegVal = ((0x00000004U << DDRC_DRAMTMG8_T_XS_FAST_X32_SHIFT - | 0x00000004U << DDRC_DRAMTMG8_T_XS_ABORT_X32_SHIFT - | 0x0000000DU << DDRC_DRAMTMG8_T_XS_DLL_X32_SHIFT - | 0x00000006U << DDRC_DRAMTMG8_T_XS_X32_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG8_OFFSET ,0x7F7F7F7FU ,0x04040D06U); - /*############################################################################################################################ */ - - /*Register : DRAMTMG9 @ 0XFD070124</p> - - DDR4 Write preamble mode - 0: 1tCK preamble - 1: 2tCK preamble Present only with MEMC_FREQ_RATIO=2 - PSU_DDRC_DRAMTMG9_DDR4_WR_PREAMBLE 0x0 - - tCCD_S: This is the minimum time between two reads or two writes for different bank group. For bank switching (from bank 'a' - o bank 'b'), the minimum time is this value + 1. For configurations with MEMC_FREQ_RATIO=2, program this to (tCCD_S/2) and ro - nd it up to the next integer value. Present only in designs configured to support DDR4. Unit: clocks. - PSU_DDRC_DRAMTMG9_T_CCD_S 0x2 - - tRRD_S: Minimum time between activates from bank 'a' to bank 'b' for different bank group. For configurations with MEMC_FREQ_ - ATIO=2, program this to (tRRD_S/2) and round it up to the next integer value. Present only in designs configured to support D - R4. Unit: Clocks. - PSU_DDRC_DRAMTMG9_T_RRD_S 0x2 - - CWL + PL + BL/2 + tWTR_S Minimum time from write command to read command for different bank group. Includes time for bus turn - round, recovery times, and all per-bank, per-rank, and global constraints. Present only in designs configured to support DDR4 - Unit: Clocks. Where: - CWL = CAS write latency - PL = Parity latency - BL = burst length. This must match the value programm - d in the BL bit of the mode register to the SDRAM - tWTR_S = internal write to read command delay for different bank group. T - is comes directly from the SDRAM specification. For configurations with MEMC_FREQ_RATIO=2, divide the value calculated using - he above equation by 2, and round it up to next integer. - PSU_DDRC_DRAMTMG9_WR2RD_S 0xb - - SDRAM Timing Register 9 - (OFFSET, MASK, VALUE) (0XFD070124, 0x40070F3FU ,0x0002020BU) - RegMask = (DDRC_DRAMTMG9_DDR4_WR_PREAMBLE_MASK | DDRC_DRAMTMG9_T_CCD_S_MASK | DDRC_DRAMTMG9_T_RRD_S_MASK | DDRC_DRAMTMG9_WR2RD_S_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_DRAMTMG9_DDR4_WR_PREAMBLE_SHIFT - | 0x00000002U << DDRC_DRAMTMG9_T_CCD_S_SHIFT - | 0x00000002U << DDRC_DRAMTMG9_T_RRD_S_SHIFT - | 0x0000000BU << DDRC_DRAMTMG9_WR2RD_S_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG9_OFFSET ,0x40070F3FU ,0x0002020BU); - /*############################################################################################################################ */ - - /*Register : DRAMTMG11 @ 0XFD07012C</p> - - tXMPDLL: This is the minimum Exit MPSM to commands requiring a locked DLL. For configurations with MEMC_FREQ_RATIO=2, program - this to (tXMPDLL/2) and round it up to the next integer value. Present only in designs configured to support DDR4. Unit: Mult - ples of 32 clocks. - PSU_DDRC_DRAMTMG11_POST_MPSM_GAP_X32 0x6f - - tMPX_LH: This is the minimum CS_n Low hold time to CKE rising edge. For configurations with MEMC_FREQ_RATIO=2, program this t - RoundUp(tMPX_LH/2)+1. Present only in designs configured to support DDR4. Unit: clocks. - PSU_DDRC_DRAMTMG11_T_MPX_LH 0x7 - - tMPX_S: Minimum time CS setup time to CKE. For configurations with MEMC_FREQ_RATIO=2, program this to (tMPX_S/2) and round it - up to the next integer value. Present only in designs configured to support DDR4. Unit: Clocks. - PSU_DDRC_DRAMTMG11_T_MPX_S 0x1 - - tCKMPE: Minimum valid clock requirement after MPSM entry. Present only in designs configured to support DDR4. Unit: Clocks. F - r configurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next i - teger. - PSU_DDRC_DRAMTMG11_T_CKMPE 0xe - - SDRAM Timing Register 11 - (OFFSET, MASK, VALUE) (0XFD07012C, 0x7F1F031FU ,0x6F07010EU) - RegMask = (DDRC_DRAMTMG11_POST_MPSM_GAP_X32_MASK | DDRC_DRAMTMG11_T_MPX_LH_MASK | DDRC_DRAMTMG11_T_MPX_S_MASK | DDRC_DRAMTMG11_T_CKMPE_MASK | 0 ); - - RegVal = ((0x0000006FU << DDRC_DRAMTMG11_POST_MPSM_GAP_X32_SHIFT - | 0x00000007U << DDRC_DRAMTMG11_T_MPX_LH_SHIFT - | 0x00000001U << DDRC_DRAMTMG11_T_MPX_S_SHIFT - | 0x0000000EU << DDRC_DRAMTMG11_T_CKMPE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG11_OFFSET ,0x7F1F031FU ,0x6F07010EU); - /*############################################################################################################################ */ - - /*Register : DRAMTMG12 @ 0XFD070130</p> - - tCMDCKE: Delay from valid command to CKE input LOW. Set this to the larger of tESCKE or tCMDCKE For configurations with MEMC_ - REQ_RATIO=2, program this to (max(tESCKE, tCMDCKE)/2) and round it up to next integer value. - PSU_DDRC_DRAMTMG12_T_CMDCKE 0x2 - - tCKEHCMD: Valid command requirement after CKE input HIGH. For configurations with MEMC_FREQ_RATIO=2, program this to (tCKEHCM - /2) and round it up to next integer value. - PSU_DDRC_DRAMTMG12_T_CKEHCMD 0x6 - - tMRD_PDA: This is the Mode Register Set command cycle time in PDA mode. For configurations with MEMC_FREQ_RATIO=2, program th - s to (tMRD_PDA/2) and round it up to next integer value. - PSU_DDRC_DRAMTMG12_T_MRD_PDA 0x8 - - SDRAM Timing Register 12 - (OFFSET, MASK, VALUE) (0XFD070130, 0x00030F1FU ,0x00020608U) - RegMask = (DDRC_DRAMTMG12_T_CMDCKE_MASK | DDRC_DRAMTMG12_T_CKEHCMD_MASK | DDRC_DRAMTMG12_T_MRD_PDA_MASK | 0 ); - - RegVal = ((0x00000002U << DDRC_DRAMTMG12_T_CMDCKE_SHIFT - | 0x00000006U << DDRC_DRAMTMG12_T_CKEHCMD_SHIFT - | 0x00000008U << DDRC_DRAMTMG12_T_MRD_PDA_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DRAMTMG12_OFFSET ,0x00030F1FU ,0x00020608U); - /*############################################################################################################################ */ - - /*Register : ZQCTL0 @ 0XFD070180</p> - - - 1 - Disable uMCTL2 generation of ZQCS/MPC(ZQ calibration) command. Register DBGCMD.zq_calib_short can be used instead to is - ue ZQ calibration request from APB module. - 0 - Internally generate ZQCS/MPC(ZQ calibration) commands based on ZQCTL1.t_zq_s - ort_interval_x1024. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices. - PSU_DDRC_ZQCTL0_DIS_AUTO_ZQ 0x1 - - - 1 - Disable issuing of ZQCL/MPC(ZQ calibration) command at Self-Refresh/SR-Powerdown exit. Only applicable when run in DDR3 - or DDR4 or LPDDR2 or LPDDR3 or LPDDR4 mode. - 0 - Enable issuing of ZQCL/MPC(ZQ calibration) command at Self-Refresh/SR-Power - own exit. Only applicable when run in DDR3 or DDR4 or LPDDR2 or LPDDR3 or LPDDR4 mode. This is only present for designs suppo - ting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices. - PSU_DDRC_ZQCTL0_DIS_SRX_ZQCL 0x0 - - - 1 - Denotes that ZQ resistor is shared between ranks. Means ZQinit/ZQCL/ZQCS/MPC(ZQ calibration) commands are sent to one r - nk at a time with tZQinit/tZQCL/tZQCS/tZQCAL/tZQLAT timing met between commands so that commands to different ranks do not ov - rlap. - 0 - ZQ resistor is not shared. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices. - PSU_DDRC_ZQCTL0_ZQ_RESISTOR_SHARED 0x0 - - - 1 - Disable issuing of ZQCL command at Maximum Power Saving Mode exit. Only applicable when run in DDR4 mode. - 0 - Enable - ssuing of ZQCL command at Maximum Power Saving Mode exit. Only applicable when run in DDR4 mode. This is only present for des - gns supporting DDR4 devices. - PSU_DDRC_ZQCTL0_DIS_MPSMX_ZQCL 0x0 - - tZQoper for DDR3/DDR4, tZQCL for LPDDR2/LPDDR3, tZQCAL for LPDDR4: Number of cycles of NOP required after a ZQCL (ZQ calibrat - on long)/MPC(ZQ Start) command is issued to SDRAM. For configurations with MEMC_FREQ_RATIO=2: DDR3/DDR4: program this to tZQo - er/2 and round it up to the next integer value. LPDDR2/LPDDR3: program this to tZQCL/2 and round it up to the next integer va - ue. LPDDR4: program this to tZQCAL/2 and round it up to the next integer value. Unit: Clock cycles. This is only present for - esigns supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices. - PSU_DDRC_ZQCTL0_T_ZQ_LONG_NOP 0x100 - - tZQCS for DDR3/DD4/LPDDR2/LPDDR3, tZQLAT for LPDDR4: Number of cycles of NOP required after a ZQCS (ZQ calibration short)/MPC - ZQ Latch) command is issued to SDRAM. For configurations with MEMC_FREQ_RATIO=2, program this to tZQCS/2 and round it up to t - e next integer value. Unit: Clock cycles. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devic - s. - PSU_DDRC_ZQCTL0_T_ZQ_SHORT_NOP 0x40 - - ZQ Control Register 0 - (OFFSET, MASK, VALUE) (0XFD070180, 0xF7FF03FFU ,0x81000040U) - RegMask = (DDRC_ZQCTL0_DIS_AUTO_ZQ_MASK | DDRC_ZQCTL0_DIS_SRX_ZQCL_MASK | DDRC_ZQCTL0_ZQ_RESISTOR_SHARED_MASK | DDRC_ZQCTL0_DIS_MPSMX_ZQCL_MASK | DDRC_ZQCTL0_T_ZQ_LONG_NOP_MASK | DDRC_ZQCTL0_T_ZQ_SHORT_NOP_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_ZQCTL0_DIS_AUTO_ZQ_SHIFT - | 0x00000000U << DDRC_ZQCTL0_DIS_SRX_ZQCL_SHIFT - | 0x00000000U << DDRC_ZQCTL0_ZQ_RESISTOR_SHARED_SHIFT - | 0x00000000U << DDRC_ZQCTL0_DIS_MPSMX_ZQCL_SHIFT - | 0x00000100U << DDRC_ZQCTL0_T_ZQ_LONG_NOP_SHIFT - | 0x00000040U << DDRC_ZQCTL0_T_ZQ_SHORT_NOP_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ZQCTL0_OFFSET ,0xF7FF03FFU ,0x81000040U); - /*############################################################################################################################ */ - - /*Register : ZQCTL1 @ 0XFD070184</p> - - tZQReset: Number of cycles of NOP required after a ZQReset (ZQ calibration Reset) command is issued to SDRAM. For configurati - ns with MEMC_FREQ_RATIO=2, program this to tZQReset/2 and round it up to the next integer value. Unit: Clock cycles. This is - nly present for designs supporting LPDDR2/LPDDR3/LPDDR4 devices. - PSU_DDRC_ZQCTL1_T_ZQ_RESET_NOP 0x20 - - Average interval to wait between automatically issuing ZQCS (ZQ calibration short)/MPC(ZQ calibration) commands to DDR3/DDR4/ - PDDR2/LPDDR3/LPDDR4 devices. Meaningless, if ZQCTL0.dis_auto_zq=1. Unit: 1024 clock cycles. This is only present for designs - upporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices. - PSU_DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024 0x19707 - - ZQ Control Register 1 - (OFFSET, MASK, VALUE) (0XFD070184, 0x3FFFFFFFU ,0x02019707U) - RegMask = (DDRC_ZQCTL1_T_ZQ_RESET_NOP_MASK | DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024_MASK | 0 ); - - RegVal = ((0x00000020U << DDRC_ZQCTL1_T_ZQ_RESET_NOP_SHIFT - | 0x00019707U << DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ZQCTL1_OFFSET ,0x3FFFFFFFU ,0x02019707U); - /*############################################################################################################################ */ - - /*Register : DFITMG0 @ 0XFD070190</p> - - Specifies the number of DFI clock cycles after an assertion or de-assertion of the DFI control signals that the control signa - s at the PHY-DRAM interface reflect the assertion or de-assertion. If the DFI clock and the memory clock are not phase-aligne - , this timing parameter should be rounded up to the next integer value. Note that if using RDIMM, it is necessary to incremen - this parameter by RDIMM's extra cycle of latency in terms of DFI clock. - PSU_DDRC_DFITMG0_DFI_T_CTRL_DELAY 0x4 - - Defines whether dfi_rddata_en/dfi_rddata/dfi_rddata_valid is generated using HDR or SDR values Selects whether value in DFITM - 0.dfi_t_rddata_en is in terms of SDR or HDR clock cycles: - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles R - fer to PHY specification for correct value. - PSU_DDRC_DFITMG0_DFI_RDDATA_USE_SDR 0x1 - - Time from the assertion of a read command on the DFI interface to the assertion of the dfi_rddata_en signal. Refer to PHY spe - ification for correct value. This corresponds to the DFI parameter trddata_en. Note that, depending on the PHY, if using RDIM - , it may be necessary to use the value (CL + 1) in the calculation of trddata_en. This is to compensate for the extra cycle o - latency through the RDIMM. Unit: Clocks - PSU_DDRC_DFITMG0_DFI_T_RDDATA_EN 0xb - - Defines whether dfi_wrdata_en/dfi_wrdata/dfi_wrdata_mask is generated using HDR or SDR values Selects whether value in DFITMG - .dfi_tphy_wrlat is in terms of SDR or HDR clock cycles Selects whether value in DFITMG0.dfi_tphy_wrdata is in terms of SDR or - HDR clock cycles - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles Refer to PHY specification for correct val - e. - PSU_DDRC_DFITMG0_DFI_WRDATA_USE_SDR 0x1 - - Specifies the number of clock cycles between when dfi_wrdata_en is asserted to when the associated write data is driven on th - dfi_wrdata signal. This corresponds to the DFI timing parameter tphy_wrdata. Refer to PHY specification for correct value. N - te, max supported value is 8. Unit: Clocks - PSU_DDRC_DFITMG0_DFI_TPHY_WRDATA 0x2 - - Write latency Number of clocks from the write command to write data enable (dfi_wrdata_en). This corresponds to the DFI timin - parameter tphy_wrlat. Refer to PHY specification for correct value.Note that, depending on the PHY, if using RDIMM, it may b - necessary to use the value (CL + 1) in the calculation of tphy_wrlat. This is to compensate for the extra cycle of latency t - rough the RDIMM. - PSU_DDRC_DFITMG0_DFI_TPHY_WRLAT 0xb - - DFI Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD070190, 0x1FBFBF3FU ,0x048B820BU) - RegMask = (DDRC_DFITMG0_DFI_T_CTRL_DELAY_MASK | DDRC_DFITMG0_DFI_RDDATA_USE_SDR_MASK | DDRC_DFITMG0_DFI_T_RDDATA_EN_MASK | DDRC_DFITMG0_DFI_WRDATA_USE_SDR_MASK | DDRC_DFITMG0_DFI_TPHY_WRDATA_MASK | DDRC_DFITMG0_DFI_TPHY_WRLAT_MASK | 0 ); - - RegVal = ((0x00000004U << DDRC_DFITMG0_DFI_T_CTRL_DELAY_SHIFT - | 0x00000001U << DDRC_DFITMG0_DFI_RDDATA_USE_SDR_SHIFT - | 0x0000000BU << DDRC_DFITMG0_DFI_T_RDDATA_EN_SHIFT - | 0x00000001U << DDRC_DFITMG0_DFI_WRDATA_USE_SDR_SHIFT - | 0x00000002U << DDRC_DFITMG0_DFI_TPHY_WRDATA_SHIFT - | 0x0000000BU << DDRC_DFITMG0_DFI_TPHY_WRLAT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DFITMG0_OFFSET ,0x1FBFBF3FU ,0x048B820BU); - /*############################################################################################################################ */ - - /*Register : DFITMG1 @ 0XFD070194</p> - - Specifies the number of DFI PHY clocks between when the dfi_cs signal is asserted and when the associated command is driven. - his field is used for CAL mode, should be set to '0' or the value which matches the CAL mode register setting in the DRAM. If - the PHY can add the latency for CAL mode, this should be set to '0'. Valid Range: 0, 3, 4, 5, 6, and 8 - PSU_DDRC_DFITMG1_DFI_T_CMD_LAT 0x0 - - Specifies the number of DFI PHY clocks between when the dfi_cs signal is asserted and when the associated dfi_parity_in signa - is driven. - PSU_DDRC_DFITMG1_DFI_T_PARIN_LAT 0x0 - - Specifies the number of DFI clocks between when the dfi_wrdata_en signal is asserted and when the corresponding write data tr - nsfer is completed on the DRAM bus. This corresponds to the DFI timing parameter twrdata_delay. Refer to PHY specification fo - correct value. For DFI 3.0 PHY, set to twrdata_delay, a new timing parameter introduced in DFI 3.0. For DFI 2.1 PHY, set to - phy_wrdata + (delay of DFI write data to the DRAM). Value to be programmed is in terms of DFI clocks, not PHY clocks. In FREQ - RATIO=2, divide PHY's value by 2 and round up to next integer. If using DFITMG0.dfi_wrdata_use_sdr=1, add 1 to the value. Uni - : Clocks - PSU_DDRC_DFITMG1_DFI_T_WRDATA_DELAY 0x3 - - Specifies the number of DFI clock cycles from the assertion of the dfi_dram_clk_disable signal on the DFI until the clock to - he DRAM memory devices, at the PHY-DRAM boundary, maintains a low value. If the DFI clock and the memory clock are not phase - ligned, this timing parameter should be rounded up to the next integer value. - PSU_DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE 0x3 - - Specifies the number of DFI clock cycles from the de-assertion of the dfi_dram_clk_disable signal on the DFI until the first - alid rising edge of the clock to the DRAM memory devices, at the PHY-DRAM boundary. If the DFI clock and the memory clock are - not phase aligned, this timing parameter should be rounded up to the next integer value. - PSU_DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE 0x4 - - DFI Timing Register 1 - (OFFSET, MASK, VALUE) (0XFD070194, 0xF31F0F0FU ,0x00030304U) - RegMask = (DDRC_DFITMG1_DFI_T_CMD_LAT_MASK | DDRC_DFITMG1_DFI_T_PARIN_LAT_MASK | DDRC_DFITMG1_DFI_T_WRDATA_DELAY_MASK | DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE_MASK | DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_DFITMG1_DFI_T_CMD_LAT_SHIFT - | 0x00000000U << DDRC_DFITMG1_DFI_T_PARIN_LAT_SHIFT - | 0x00000003U << DDRC_DFITMG1_DFI_T_WRDATA_DELAY_SHIFT - | 0x00000003U << DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE_SHIFT - | 0x00000004U << DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DFITMG1_OFFSET ,0xF31F0F0FU ,0x00030304U); - /*############################################################################################################################ */ - - /*Register : DFILPCFG0 @ 0XFD070198</p> - - Setting for DFI's tlp_resp time. Same value is used for both Power Down, Self Refresh, Deep Power Down and Maximum Power Savi - g modes. DFI 2.1 specification onwards, recommends using a fixed value of 7 always. - PSU_DDRC_DFILPCFG0_DFI_TLP_RESP 0x7 - - Value to drive on dfi_lp_wakeup signal when Deep Power Down mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - 16 - cycles - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - - 2048 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0xD - - 31072 cycles - 0xE - 262144 cycles - 0xF - Unlimited This is only present for designs supporting mDDR or LPDDR2/LPDDR3 device - . - PSU_DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD 0x0 - - Enables DFI Low Power interface handshaking during Deep Power Down Entry/Exit. - 0 - Disabled - 1 - Enabled This is only pres - nt for designs supporting mDDR or LPDDR2/LPDDR3 devices. - PSU_DDRC_DFILPCFG0_DFI_LP_EN_DPD 0x0 - - Value to drive on dfi_lp_wakeup signal when Self Refresh mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - 16 cy - les - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - - 048 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0xD - 131 - 72 cycles - 0xE - 262144 cycles - 0xF - Unlimited - PSU_DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR 0x0 - - Enables DFI Low Power interface handshaking during Self Refresh Entry/Exit. - 0 - Disabled - 1 - Enabled - PSU_DDRC_DFILPCFG0_DFI_LP_EN_SR 0x1 - - Value to drive on dfi_lp_wakeup signal when Power Down mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - 16 cycl - s - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - 20 - 8 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0xD - 13107 - cycles - 0xE - 262144 cycles - 0xF - Unlimited - PSU_DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD 0x0 - - Enables DFI Low Power interface handshaking during Power Down Entry/Exit. - 0 - Disabled - 1 - Enabled - PSU_DDRC_DFILPCFG0_DFI_LP_EN_PD 0x1 - - DFI Low Power Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD070198, 0x0FF1F1F1U ,0x07000101U) - RegMask = (DDRC_DFILPCFG0_DFI_TLP_RESP_MASK | DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD_MASK | DDRC_DFILPCFG0_DFI_LP_EN_DPD_MASK | DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR_MASK | DDRC_DFILPCFG0_DFI_LP_EN_SR_MASK | DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD_MASK | DDRC_DFILPCFG0_DFI_LP_EN_PD_MASK | 0 ); - - RegVal = ((0x00000007U << DDRC_DFILPCFG0_DFI_TLP_RESP_SHIFT - | 0x00000000U << DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD_SHIFT - | 0x00000000U << DDRC_DFILPCFG0_DFI_LP_EN_DPD_SHIFT - | 0x00000000U << DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR_SHIFT - | 0x00000001U << DDRC_DFILPCFG0_DFI_LP_EN_SR_SHIFT - | 0x00000000U << DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD_SHIFT - | 0x00000001U << DDRC_DFILPCFG0_DFI_LP_EN_PD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DFILPCFG0_OFFSET ,0x0FF1F1F1U ,0x07000101U); - /*############################################################################################################################ */ - - /*Register : DFILPCFG1 @ 0XFD07019C</p> - - Value to drive on dfi_lp_wakeup signal when Maximum Power Saving Mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - - 16 cycles - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - 2048 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0 - D - 131072 cycles - 0xE - 262144 cycles - 0xF - Unlimited This is only present for designs supporting DDR4 devices. - PSU_DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM 0x2 - - Enables DFI Low Power interface handshaking during Maximum Power Saving Mode Entry/Exit. - 0 - Disabled - 1 - Enabled This is - only present for designs supporting DDR4 devices. - PSU_DDRC_DFILPCFG1_DFI_LP_EN_MPSM 0x1 - - DFI Low Power Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD07019C, 0x000000F1U ,0x00000021U) - RegMask = (DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM_MASK | DDRC_DFILPCFG1_DFI_LP_EN_MPSM_MASK | 0 ); - - RegVal = ((0x00000002U << DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM_SHIFT - | 0x00000001U << DDRC_DFILPCFG1_DFI_LP_EN_MPSM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DFILPCFG1_OFFSET ,0x000000F1U ,0x00000021U); - /*############################################################################################################################ */ - - /*Register : DFIUPD1 @ 0XFD0701A4</p> - - This is the minimum amount of time between uMCTL2 initiated DFI update requests (which is executed whenever the uMCTL2 is idl - ). Set this number higher to reduce the frequency of update requests, which can have a small impact on the latency of the fir - t read request when the uMCTL2 is idle. Unit: 1024 clocks - PSU_DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024 0x41 - - This is the maximum amount of time between uMCTL2 initiated DFI update requests. This timer resets with each update request; - hen the timer expires dfi_ctrlupd_req is sent and traffic is blocked until the dfi_ctrlupd_ackx is received. PHY can use this - idle time to recalibrate the delay lines to the DLLs. The DFI controller update is also used to reset PHY FIFO pointers in ca - e of data capture errors. Updates are required to maintain calibration over PVT, but frequent updates may impact performance. - Note: Value programmed for DFIUPD1.dfi_t_ctrlupd_interval_max_x1024 must be greater than DFIUPD1.dfi_t_ctrlupd_interval_min_x - 024. Unit: 1024 clocks - PSU_DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024 0xe2 - - DFI Update Register 1 - (OFFSET, MASK, VALUE) (0XFD0701A4, 0x00FF00FFU ,0x004100E2U) - RegMask = (DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024_MASK | DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024_MASK | 0 ); - - RegVal = ((0x00000041U << DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024_SHIFT - | 0x000000E2U << DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DFIUPD1_OFFSET ,0x00FF00FFU ,0x004100E2U); - /*############################################################################################################################ */ - - /*Register : DFIMISC @ 0XFD0701B0</p> - - Defines polarity of dfi_wrdata_cs and dfi_rddata_cs signals. - 0: Signals are active low - 1: Signals are active high - PSU_DDRC_DFIMISC_DFI_DATA_CS_POLARITY 0x0 - - DBI implemented in DDRC or PHY. - 0 - DDRC implements DBI functionality. - 1 - PHY implements DBI functionality. Present only - in designs configured to support DDR4 and LPDDR4. - PSU_DDRC_DFIMISC_PHY_DBI_MODE 0x0 - - PHY initialization complete enable signal. When asserted the dfi_init_complete signal can be used to trigger SDRAM initialisa - ion - PSU_DDRC_DFIMISC_DFI_INIT_COMPLETE_EN 0x0 - - DFI Miscellaneous Control Register - (OFFSET, MASK, VALUE) (0XFD0701B0, 0x00000007U ,0x00000000U) - RegMask = (DDRC_DFIMISC_DFI_DATA_CS_POLARITY_MASK | DDRC_DFIMISC_PHY_DBI_MODE_MASK | DDRC_DFIMISC_DFI_INIT_COMPLETE_EN_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_DFIMISC_DFI_DATA_CS_POLARITY_SHIFT - | 0x00000000U << DDRC_DFIMISC_PHY_DBI_MODE_SHIFT - | 0x00000000U << DDRC_DFIMISC_DFI_INIT_COMPLETE_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DFIMISC_OFFSET ,0x00000007U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DFITMG2 @ 0XFD0701B4</p> - - >Number of clocks between when a read command is sent on the DFI control interface and when the associated dfi_rddata_cs sign - l is asserted. This corresponds to the DFI timing parameter tphy_rdcslat. Refer to PHY specification for correct value. - PSU_DDRC_DFITMG2_DFI_TPHY_RDCSLAT 0x9 - - Number of clocks between when a write command is sent on the DFI control interface and when the associated dfi_wrdata_cs sign - l is asserted. This corresponds to the DFI timing parameter tphy_wrcslat. Refer to PHY specification for correct value. - PSU_DDRC_DFITMG2_DFI_TPHY_WRCSLAT 0x6 - - DFI Timing Register 2 - (OFFSET, MASK, VALUE) (0XFD0701B4, 0x00003F3FU ,0x00000906U) - RegMask = (DDRC_DFITMG2_DFI_TPHY_RDCSLAT_MASK | DDRC_DFITMG2_DFI_TPHY_WRCSLAT_MASK | 0 ); - - RegVal = ((0x00000009U << DDRC_DFITMG2_DFI_TPHY_RDCSLAT_SHIFT - | 0x00000006U << DDRC_DFITMG2_DFI_TPHY_WRCSLAT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DFITMG2_OFFSET ,0x00003F3FU ,0x00000906U); - /*############################################################################################################################ */ - - /*Register : DBICTL @ 0XFD0701C0</p> - - Read DBI enable signal in DDRC. - 0 - Read DBI is disabled. - 1 - Read DBI is enabled. This signal must be set the same value - as DRAM's mode register. - DDR4: MR5 bit A12. When x4 devices are used, this signal must be set to 0. - LPDDR4: MR3[6] - PSU_DDRC_DBICTL_RD_DBI_EN 0x0 - - Write DBI enable signal in DDRC. - 0 - Write DBI is disabled. - 1 - Write DBI is enabled. This signal must be set the same va - ue as DRAM's mode register. - DDR4: MR5 bit A11. When x4 devices are used, this signal must be set to 0. - LPDDR4: MR3[7] - PSU_DDRC_DBICTL_WR_DBI_EN 0x0 - - DM enable signal in DDRC. - 0 - DM is disabled. - 1 - DM is enabled. This signal must be set the same logical value as DRAM's - mode register. - DDR4: Set this to same value as MR5 bit A10. When x4 devices are used, this signal must be set to 0. - LPDDR - : Set this to inverted value of MR13[5] which is opposite polarity from this signal - PSU_DDRC_DBICTL_DM_EN 0x1 - - DM/DBI Control Register - (OFFSET, MASK, VALUE) (0XFD0701C0, 0x00000007U ,0x00000001U) - RegMask = (DDRC_DBICTL_RD_DBI_EN_MASK | DDRC_DBICTL_WR_DBI_EN_MASK | DDRC_DBICTL_DM_EN_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_DBICTL_RD_DBI_EN_SHIFT - | 0x00000000U << DDRC_DBICTL_WR_DBI_EN_SHIFT - | 0x00000001U << DDRC_DBICTL_DM_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DBICTL_OFFSET ,0x00000007U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : ADDRMAP0 @ 0XFD070200</p> - - Selects the HIF address bit used as rank address bit 0. Valid Range: 0 to 27, and 31 Internal Base: 6 The selected HIF addres - bit is determined by adding the internal base to the value of this field. If set to 31, rank address bit 0 is set to 0. - PSU_DDRC_ADDRMAP0_ADDRMAP_CS_BIT0 0x1f - - Address Map Register 0 - (OFFSET, MASK, VALUE) (0XFD070200, 0x0000001FU ,0x0000001FU) - RegMask = (DDRC_ADDRMAP0_ADDRMAP_CS_BIT0_MASK | 0 ); - - RegVal = ((0x0000001FU << DDRC_ADDRMAP0_ADDRMAP_CS_BIT0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP0_OFFSET ,0x0000001FU ,0x0000001FU); - /*############################################################################################################################ */ - - /*Register : ADDRMAP1 @ 0XFD070204</p> - - Selects the HIF address bit used as bank address bit 2. Valid Range: 0 to 29 and 31 Internal Base: 4 The selected HIF address - bit is determined by adding the internal base to the value of this field. If set to 31, bank address bit 2 is set to 0. - PSU_DDRC_ADDRMAP1_ADDRMAP_BANK_B2 0x1f - - Selects the HIF address bits used as bank address bit 1. Valid Range: 0 to 30 Internal Base: 3 The selected HIF address bit f - r each of the bank address bits is determined by adding the internal base to the value of this field. - PSU_DDRC_ADDRMAP1_ADDRMAP_BANK_B1 0xa - - Selects the HIF address bits used as bank address bit 0. Valid Range: 0 to 30 Internal Base: 2 The selected HIF address bit f - r each of the bank address bits is determined by adding the internal base to the value of this field. - PSU_DDRC_ADDRMAP1_ADDRMAP_BANK_B0 0xa - - Address Map Register 1 - (OFFSET, MASK, VALUE) (0XFD070204, 0x001F1F1FU ,0x001F0A0AU) - RegMask = (DDRC_ADDRMAP1_ADDRMAP_BANK_B2_MASK | DDRC_ADDRMAP1_ADDRMAP_BANK_B1_MASK | DDRC_ADDRMAP1_ADDRMAP_BANK_B0_MASK | 0 ); - - RegVal = ((0x0000001FU << DDRC_ADDRMAP1_ADDRMAP_BANK_B2_SHIFT - | 0x0000000AU << DDRC_ADDRMAP1_ADDRMAP_BANK_B1_SHIFT - | 0x0000000AU << DDRC_ADDRMAP1_ADDRMAP_BANK_B0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP1_OFFSET ,0x001F1F1FU ,0x001F0A0AU); - /*############################################################################################################################ */ - - /*Register : ADDRMAP2 @ 0XFD070208</p> - - - Full bus width mode: Selects the HIF address bit used as column address bit 5. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 6. - Quarter bus width mode: Selects the HIF address bit used as column address bit 7 . Vali - Range: 0 to 7, and 15 Internal Base: 5 The selected HIF address bit is determined by adding the internal base to the value o - this field. If set to 15, this column address bit is set to 0. - PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B5 0x0 - - - Full bus width mode: Selects the HIF address bit used as column address bit 4. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 5. - Quarter bus width mode: Selects the HIF address bit used as column address bit 6. Valid - Range: 0 to 7, and 15 Internal Base: 4 The selected HIF address bit is determined by adding the internal base to the value of - this field. If set to 15, this column address bit is set to 0. - PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B4 0x0 - - - Full bus width mode: Selects the HIF address bit used as column address bit 3. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 4. - Quarter bus width mode: Selects the HIF address bit used as column address bit 5. Valid - Range: 0 to 7 Internal Base: 3 The selected HIF address bit is determined by adding the internal base to the value of this fi - ld. Note, if UMCTL2_INCL_ARB=1 and MEMC_BURST_LENGTH=16, it is required to program this to 0, hence register does not exist i - this case. - PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B3 0x0 - - - Full bus width mode: Selects the HIF address bit used as column address bit 2. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 3. - Quarter bus width mode: Selects the HIF address bit used as column address bit 4. Valid - Range: 0 to 7 Internal Base: 2 The selected HIF address bit is determined by adding the internal base to the value of this fi - ld. Note, if UMCTL2_INCL_ARB=1 and MEMC_BURST_LENGTH=8 or 16, it is required to program this to 0. - PSU_DDRC_ADDRMAP2_ADDRMAP_COL_B2 0x0 - - Address Map Register 2 - (OFFSET, MASK, VALUE) (0XFD070208, 0x0F0F0F0FU ,0x00000000U) - RegMask = (DDRC_ADDRMAP2_ADDRMAP_COL_B5_MASK | DDRC_ADDRMAP2_ADDRMAP_COL_B4_MASK | DDRC_ADDRMAP2_ADDRMAP_COL_B3_MASK | DDRC_ADDRMAP2_ADDRMAP_COL_B2_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_ADDRMAP2_ADDRMAP_COL_B5_SHIFT - | 0x00000000U << DDRC_ADDRMAP2_ADDRMAP_COL_B4_SHIFT - | 0x00000000U << DDRC_ADDRMAP2_ADDRMAP_COL_B3_SHIFT - | 0x00000000U << DDRC_ADDRMAP2_ADDRMAP_COL_B2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP2_OFFSET ,0x0F0F0F0FU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : ADDRMAP3 @ 0XFD07020C</p> - - - Full bus width mode: Selects the HIF address bit used as column address bit 9. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 11 (10 in LPDDR2/LPDDR3 mode). - Quarter bus width mode: Selects the HIF address bit used as - column address bit 13 (11 in LPDDR2/LPDDR3 mode). Valid Range: 0 to 7, and 15 Internal Base: 9 The selected HIF address bit i - determined by adding the internal base to the value of this field. If set to 15, this column address bit is set to 0. Note: - er JEDEC DDR2/3/mDDR specification, column address bit 10 is reserved for indicating auto-precharge, and hence no source addr - ss bit can be mapped to column address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus an - hence column bit 10 is used. - PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B9 0x0 - - - Full bus width mode: Selects the HIF address bit used as column address bit 8. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 9. - Quarter bus width mode: Selects the HIF address bit used as column address bit 11 (10 i - LPDDR2/LPDDR3 mode). Valid Range: 0 to 7, and 15 Internal Base: 8 The selected HIF address bit is determined by adding the i - ternal base to the value of this field. If set to 15, this column address bit is set to 0. Note: Per JEDEC DDR2/3/mDDR specif - cation, column address bit 10 is reserved for indicating auto-precharge, and hence no source address bit can be mapped to col - mn address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus and hence column bit 10 is use - . - PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B8 0x0 - - - Full bus width mode: Selects the HIF address bit used as column address bit 7. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 8. - Quarter bus width mode: Selects the HIF address bit used as column address bit 9. Valid - Range: 0 to 7, and 15 Internal Base: 7 The selected HIF address bit is determined by adding the internal base to the value of - this field. If set to 15, this column address bit is set to 0. - PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B7 0x0 - - - Full bus width mode: Selects the HIF address bit used as column address bit 6. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 7. - Quarter bus width mode: Selects the HIF address bit used as column address bit 8. Valid - Range: 0 to 7, and 15 Internal Base: 6 The selected HIF address bit is determined by adding the internal base to the value of - this field. If set to 15, this column address bit is set to 0. - PSU_DDRC_ADDRMAP3_ADDRMAP_COL_B6 0x0 - - Address Map Register 3 - (OFFSET, MASK, VALUE) (0XFD07020C, 0x0F0F0F0FU ,0x00000000U) - RegMask = (DDRC_ADDRMAP3_ADDRMAP_COL_B9_MASK | DDRC_ADDRMAP3_ADDRMAP_COL_B8_MASK | DDRC_ADDRMAP3_ADDRMAP_COL_B7_MASK | DDRC_ADDRMAP3_ADDRMAP_COL_B6_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_ADDRMAP3_ADDRMAP_COL_B9_SHIFT - | 0x00000000U << DDRC_ADDRMAP3_ADDRMAP_COL_B8_SHIFT - | 0x00000000U << DDRC_ADDRMAP3_ADDRMAP_COL_B7_SHIFT - | 0x00000000U << DDRC_ADDRMAP3_ADDRMAP_COL_B6_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP3_OFFSET ,0x0F0F0F0FU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : ADDRMAP4 @ 0XFD070210</p> - - - Full bus width mode: Selects the HIF address bit used as column address bit 13 (11 in LPDDR2/LPDDR3 mode). - Half bus width - mode: Unused. To make it unused, this should be tied to 4'hF. - Quarter bus width mode: Unused. To make it unused, this must - e tied to 4'hF. Valid Range: 0 to 7, and 15 Internal Base: 11 The selected HIF address bit is determined by adding the intern - l base to the value of this field. If set to 15, this column address bit is set to 0. Note: Per JEDEC DDR2/3/mDDR specificati - n, column address bit 10 is reserved for indicating auto-precharge, and hence no source address bit can be mapped to column a - dress bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus and hence column bit 10 is used. - PSU_DDRC_ADDRMAP4_ADDRMAP_COL_B11 0xf - - - Full bus width mode: Selects the HIF address bit used as column address bit 11 (10 in LPDDR2/LPDDR3 mode). - Half bus width - mode: Selects the HIF address bit used as column address bit 13 (11 in LPDDR2/LPDDR3 mode). - Quarter bus width mode: UNUSED. - To make it unused, this must be tied to 4'hF. Valid Range: 0 to 7, and 15 Internal Base: 10 The selected HIF address bit is d - termined by adding the internal base to the value of this field. If set to 15, this column address bit is set to 0. Note: Per - JEDEC DDR2/3/mDDR specification, column address bit 10 is reserved for indicating auto-precharge, and hence no source address - bit can be mapped to column address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus and h - nce column bit 10 is used. - PSU_DDRC_ADDRMAP4_ADDRMAP_COL_B10 0xf - - Address Map Register 4 - (OFFSET, MASK, VALUE) (0XFD070210, 0x00000F0FU ,0x00000F0FU) - RegMask = (DDRC_ADDRMAP4_ADDRMAP_COL_B11_MASK | DDRC_ADDRMAP4_ADDRMAP_COL_B10_MASK | 0 ); - - RegVal = ((0x0000000FU << DDRC_ADDRMAP4_ADDRMAP_COL_B11_SHIFT - | 0x0000000FU << DDRC_ADDRMAP4_ADDRMAP_COL_B10_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP4_OFFSET ,0x00000F0FU ,0x00000F0FU); - /*############################################################################################################################ */ - - /*Register : ADDRMAP5 @ 0XFD070214</p> - - Selects the HIF address bit used as row address bit 11. Valid Range: 0 to 11, and 15 Internal Base: 17 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 11 is set to 0. - PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B11 0x8 - - Selects the HIF address bits used as row address bits 2 to 10. Valid Range: 0 to 11, and 15 Internal Base: 8 (for row address - bit 2), 9 (for row address bit 3), 10 (for row address bit 4) etc increasing to 16 (for row address bit 10) The selected HIF - ddress bit for each of the row address bits is determined by adding the internal base to the value of this field. When value - 5 is used the values of row address bits 2 to 10 are defined by registers ADDRMAP9, ADDRMAP10, ADDRMAP11. - PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10 0xf - - Selects the HIF address bits used as row address bit 1. Valid Range: 0 to 11 Internal Base: 7 The selected HIF address bit fo - each of the row address bits is determined by adding the internal base to the value of this field. - PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B1 0x8 - - Selects the HIF address bits used as row address bit 0. Valid Range: 0 to 11 Internal Base: 6 The selected HIF address bit fo - each of the row address bits is determined by adding the internal base to the value of this field. - PSU_DDRC_ADDRMAP5_ADDRMAP_ROW_B0 0x8 - - Address Map Register 5 - (OFFSET, MASK, VALUE) (0XFD070214, 0x0F0F0F0FU ,0x080F0808U) - RegMask = (DDRC_ADDRMAP5_ADDRMAP_ROW_B11_MASK | DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10_MASK | DDRC_ADDRMAP5_ADDRMAP_ROW_B1_MASK | DDRC_ADDRMAP5_ADDRMAP_ROW_B0_MASK | 0 ); - - RegVal = ((0x00000008U << DDRC_ADDRMAP5_ADDRMAP_ROW_B11_SHIFT - | 0x0000000FU << DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10_SHIFT - | 0x00000008U << DDRC_ADDRMAP5_ADDRMAP_ROW_B1_SHIFT - | 0x00000008U << DDRC_ADDRMAP5_ADDRMAP_ROW_B0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP5_OFFSET ,0x0F0F0F0FU ,0x080F0808U); - /*############################################################################################################################ */ - - /*Register : ADDRMAP6 @ 0XFD070218</p> - - Set this to 1 if there is an LPDDR3 SDRAM 6Gb or 12Gb device in use. - 1 - LPDDR3 SDRAM 6Gb/12Gb device in use. Every address - having row[14:13]==2'b11 is considered as invalid - 0 - non-LPDDR3 6Gb/12Gb device in use. All addresses are valid Present on - y in designs configured to support LPDDR3. - PSU_DDRC_ADDRMAP6_LPDDR3_6GB_12GB 0x0 - - Selects the HIF address bit used as row address bit 15. Valid Range: 0 to 11, and 15 Internal Base: 21 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 15 is set to 0. - PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B15 0xf - - Selects the HIF address bit used as row address bit 14. Valid Range: 0 to 11, and 15 Internal Base: 20 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 14 is set to 0. - PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B14 0x8 - - Selects the HIF address bit used as row address bit 13. Valid Range: 0 to 11, and 15 Internal Base: 19 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 13 is set to 0. - PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B13 0x8 - - Selects the HIF address bit used as row address bit 12. Valid Range: 0 to 11, and 15 Internal Base: 18 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 12 is set to 0. - PSU_DDRC_ADDRMAP6_ADDRMAP_ROW_B12 0x8 - - Address Map Register 6 - (OFFSET, MASK, VALUE) (0XFD070218, 0x8F0F0F0FU ,0x0F080808U) - RegMask = (DDRC_ADDRMAP6_LPDDR3_6GB_12GB_MASK | DDRC_ADDRMAP6_ADDRMAP_ROW_B15_MASK | DDRC_ADDRMAP6_ADDRMAP_ROW_B14_MASK | DDRC_ADDRMAP6_ADDRMAP_ROW_B13_MASK | DDRC_ADDRMAP6_ADDRMAP_ROW_B12_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_ADDRMAP6_LPDDR3_6GB_12GB_SHIFT - | 0x0000000FU << DDRC_ADDRMAP6_ADDRMAP_ROW_B15_SHIFT - | 0x00000008U << DDRC_ADDRMAP6_ADDRMAP_ROW_B14_SHIFT - | 0x00000008U << DDRC_ADDRMAP6_ADDRMAP_ROW_B13_SHIFT - | 0x00000008U << DDRC_ADDRMAP6_ADDRMAP_ROW_B12_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP6_OFFSET ,0x8F0F0F0FU ,0x0F080808U); - /*############################################################################################################################ */ - - /*Register : ADDRMAP7 @ 0XFD07021C</p> - - Selects the HIF address bit used as row address bit 17. Valid Range: 0 to 10, and 15 Internal Base: 23 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 17 is set to 0. - PSU_DDRC_ADDRMAP7_ADDRMAP_ROW_B17 0xf - - Selects the HIF address bit used as row address bit 16. Valid Range: 0 to 11, and 15 Internal Base: 22 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 16 is set to 0. - PSU_DDRC_ADDRMAP7_ADDRMAP_ROW_B16 0xf - - Address Map Register 7 - (OFFSET, MASK, VALUE) (0XFD07021C, 0x00000F0FU ,0x00000F0FU) - RegMask = (DDRC_ADDRMAP7_ADDRMAP_ROW_B17_MASK | DDRC_ADDRMAP7_ADDRMAP_ROW_B16_MASK | 0 ); - - RegVal = ((0x0000000FU << DDRC_ADDRMAP7_ADDRMAP_ROW_B17_SHIFT - | 0x0000000FU << DDRC_ADDRMAP7_ADDRMAP_ROW_B16_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP7_OFFSET ,0x00000F0FU ,0x00000F0FU); - /*############################################################################################################################ */ - - /*Register : ADDRMAP8 @ 0XFD070220</p> - - Selects the HIF address bits used as bank group address bit 1. Valid Range: 0 to 30, and 31 Internal Base: 3 The selected HIF - address bit for each of the bank group address bits is determined by adding the internal base to the value of this field. If - et to 31, bank group address bit 1 is set to 0. - PSU_DDRC_ADDRMAP8_ADDRMAP_BG_B1 0x8 - - Selects the HIF address bits used as bank group address bit 0. Valid Range: 0 to 30 Internal Base: 2 The selected HIF address - bit for each of the bank group address bits is determined by adding the internal base to the value of this field. - PSU_DDRC_ADDRMAP8_ADDRMAP_BG_B0 0x8 - - Address Map Register 8 - (OFFSET, MASK, VALUE) (0XFD070220, 0x00001F1FU ,0x00000808U) - RegMask = (DDRC_ADDRMAP8_ADDRMAP_BG_B1_MASK | DDRC_ADDRMAP8_ADDRMAP_BG_B0_MASK | 0 ); - - RegVal = ((0x00000008U << DDRC_ADDRMAP8_ADDRMAP_BG_B1_SHIFT - | 0x00000008U << DDRC_ADDRMAP8_ADDRMAP_BG_B0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP8_OFFSET ,0x00001F1FU ,0x00000808U); - /*############################################################################################################################ */ - - /*Register : ADDRMAP9 @ 0XFD070224</p> - - Selects the HIF address bits used as row address bit 5. Valid Range: 0 to 11 Internal Base: 11 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15. - PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B5 0x8 - - Selects the HIF address bits used as row address bit 4. Valid Range: 0 to 11 Internal Base: 10 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15. - PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B4 0x8 - - Selects the HIF address bits used as row address bit 3. Valid Range: 0 to 11 Internal Base: 9 The selected HIF address bit fo - each of the row address bits is determined by adding the internal base to the value of this field. This register field is us - d only when ADDRMAP5.addrmap_row_b2_10 is set to value 15. - PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B3 0x8 - - Selects the HIF address bits used as row address bit 2. Valid Range: 0 to 11 Internal Base: 8 The selected HIF address bit fo - each of the row address bits is determined by adding the internal base to the value of this field. This register field is us - d only when ADDRMAP5.addrmap_row_b2_10 is set to value 15. - PSU_DDRC_ADDRMAP9_ADDRMAP_ROW_B2 0x8 - - Address Map Register 9 - (OFFSET, MASK, VALUE) (0XFD070224, 0x0F0F0F0FU ,0x08080808U) - RegMask = (DDRC_ADDRMAP9_ADDRMAP_ROW_B5_MASK | DDRC_ADDRMAP9_ADDRMAP_ROW_B4_MASK | DDRC_ADDRMAP9_ADDRMAP_ROW_B3_MASK | DDRC_ADDRMAP9_ADDRMAP_ROW_B2_MASK | 0 ); - - RegVal = ((0x00000008U << DDRC_ADDRMAP9_ADDRMAP_ROW_B5_SHIFT - | 0x00000008U << DDRC_ADDRMAP9_ADDRMAP_ROW_B4_SHIFT - | 0x00000008U << DDRC_ADDRMAP9_ADDRMAP_ROW_B3_SHIFT - | 0x00000008U << DDRC_ADDRMAP9_ADDRMAP_ROW_B2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP9_OFFSET ,0x0F0F0F0FU ,0x08080808U); - /*############################################################################################################################ */ - - /*Register : ADDRMAP10 @ 0XFD070228</p> - - Selects the HIF address bits used as row address bit 9. Valid Range: 0 to 11 Internal Base: 15 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15. - PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B9 0x8 - - Selects the HIF address bits used as row address bit 8. Valid Range: 0 to 11 Internal Base: 14 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15. - PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B8 0x8 - - Selects the HIF address bits used as row address bit 7. Valid Range: 0 to 11 Internal Base: 13 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15. - PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B7 0x8 - - Selects the HIF address bits used as row address bit 6. Valid Range: 0 to 11 Internal Base: 12 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15. - PSU_DDRC_ADDRMAP10_ADDRMAP_ROW_B6 0x8 - - Address Map Register 10 - (OFFSET, MASK, VALUE) (0XFD070228, 0x0F0F0F0FU ,0x08080808U) - RegMask = (DDRC_ADDRMAP10_ADDRMAP_ROW_B9_MASK | DDRC_ADDRMAP10_ADDRMAP_ROW_B8_MASK | DDRC_ADDRMAP10_ADDRMAP_ROW_B7_MASK | DDRC_ADDRMAP10_ADDRMAP_ROW_B6_MASK | 0 ); - - RegVal = ((0x00000008U << DDRC_ADDRMAP10_ADDRMAP_ROW_B9_SHIFT - | 0x00000008U << DDRC_ADDRMAP10_ADDRMAP_ROW_B8_SHIFT - | 0x00000008U << DDRC_ADDRMAP10_ADDRMAP_ROW_B7_SHIFT - | 0x00000008U << DDRC_ADDRMAP10_ADDRMAP_ROW_B6_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP10_OFFSET ,0x0F0F0F0FU ,0x08080808U); - /*############################################################################################################################ */ - - /*Register : ADDRMAP11 @ 0XFD07022C</p> - - Selects the HIF address bits used as row address bit 10. Valid Range: 0 to 11 Internal Base: 16 The selected HIF address bit - or each of the row address bits is determined by adding the internal base to the value of this field. This register field is - sed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15. - PSU_DDRC_ADDRMAP11_ADDRMAP_ROW_B10 0x8 - - Address Map Register 11 - (OFFSET, MASK, VALUE) (0XFD07022C, 0x0000000FU ,0x00000008U) - RegMask = (DDRC_ADDRMAP11_ADDRMAP_ROW_B10_MASK | 0 ); - - RegVal = ((0x00000008U << DDRC_ADDRMAP11_ADDRMAP_ROW_B10_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ADDRMAP11_OFFSET ,0x0000000FU ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : ODTCFG @ 0XFD070240</p> - - Cycles to hold ODT for a write command. The minimum supported value is 2. Recommended values: DDR2: - BL8: 0x5 (DDR2-400/533/ - 67), 0x6 (DDR2-800), 0x7 (DDR2-1066) - BL4: 0x3 (DDR2-400/533/667), 0x4 (DDR2-800), 0x5 (DDR2-1066) DDR3: - BL8: 0x6 DDR4: - - L8: 5 + WR_PREAMBLE + CRC_MODE WR_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK write preamble) CRC_MODE = 0 (not CRC mode), 1 - CRC mode) LPDDR3: - BL8: 7 + RU(tODTon(max)/tCK) - PSU_DDRC_ODTCFG_WR_ODT_HOLD 0x6 - - The delay, in clock cycles, from issuing a write command to setting ODT values associated with that command. ODT setting must - remain constant for the entire time that DQS is driven by the uMCTL2. Recommended values: DDR2: - CWL + AL - 3 (DDR2-400/533/ - 67), CWL + AL - 4 (DDR2-800), CWL + AL - 5 (DDR2-1066) If (CWL + AL - 3 < 0), uMCTL2 does not support ODT for write operation - DDR3: - 0x0 DDR4: - DFITMG1.dfi_t_cmd_lat (to adjust for CAL mode) LPDDR3: - WL - 1 - RU(tODTon(max)/tCK)) - PSU_DDRC_ODTCFG_WR_ODT_DELAY 0x0 - - Cycles to hold ODT for a read command. The minimum supported value is 2. Recommended values: DDR2: - BL8: 0x6 (not DDR2-1066) - 0x7 (DDR2-1066) - BL4: 0x4 (not DDR2-1066), 0x5 (DDR2-1066) DDR3: - BL8 - 0x6 DDR4: - BL8: 5 + RD_PREAMBLE RD_PREAMBLE = 1 ( - tCK write preamble), 2 (2tCK write preamble) LPDDR3: - BL8: 5 + RU(tDQSCK(max)/tCK) - RD(tDQSCK(min)/tCK) + RU(tODTon(max)/tC - ) - PSU_DDRC_ODTCFG_RD_ODT_HOLD 0x6 - - The delay, in clock cycles, from issuing a read command to setting ODT values associated with that command. ODT setting must - emain constant for the entire time that DQS is driven by the uMCTL2. Recommended values: DDR2: - CL + AL - 4 (not DDR2-1066), - CL + AL - 5 (DDR2-1066) If (CL + AL - 4 < 0), uMCTL2 does not support ODT for read operation. DDR3: - CL - CWL DDR4: - CL - C - L - RD_PREAMBLE + WR_PREAMBLE + DFITMG1.dfi_t_cmd_lat (to adjust for CAL mode) WR_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK - write preamble) RD_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK write preamble) If (CL - CWL - RD_PREAMBLE + WR_PREAMBLE) < 0, - uMCTL2 does not support ODT for read operation. LPDDR3: - RL + RD(tDQSCK(min)/tCK) - 1 - RU(tODTon(max)/tCK) - PSU_DDRC_ODTCFG_RD_ODT_DELAY 0x0 - - ODT Configuration Register - (OFFSET, MASK, VALUE) (0XFD070240, 0x0F1F0F7CU ,0x06000600U) - RegMask = (DDRC_ODTCFG_WR_ODT_HOLD_MASK | DDRC_ODTCFG_WR_ODT_DELAY_MASK | DDRC_ODTCFG_RD_ODT_HOLD_MASK | DDRC_ODTCFG_RD_ODT_DELAY_MASK | 0 ); - - RegVal = ((0x00000006U << DDRC_ODTCFG_WR_ODT_HOLD_SHIFT - | 0x00000000U << DDRC_ODTCFG_WR_ODT_DELAY_SHIFT - | 0x00000006U << DDRC_ODTCFG_RD_ODT_HOLD_SHIFT - | 0x00000000U << DDRC_ODTCFG_RD_ODT_DELAY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ODTCFG_OFFSET ,0x0F1F0F7CU ,0x06000600U); - /*############################################################################################################################ */ - - /*Register : ODTMAP @ 0XFD070244</p> - - Indicates which remote ODTs must be turned on during a read from rank 1. Each rank has a remote ODT (in the SDRAM) which can - e turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB - etc. For each rank, set its bit to 1 to enable its ODT. Present only in configurations that have 2 or more ranks - PSU_DDRC_ODTMAP_RANK1_RD_ODT 0x0 - - Indicates which remote ODTs must be turned on during a write to rank 1. Each rank has a remote ODT (in the SDRAM) which can b - turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB, - etc. For each rank, set its bit to 1 to enable its ODT. Present only in configurations that have 2 or more ranks - PSU_DDRC_ODTMAP_RANK1_WR_ODT 0x0 - - Indicates which remote ODTs must be turned on during a read from rank 0. Each rank has a remote ODT (in the SDRAM) which can - e turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB - etc. For each rank, set its bit to 1 to enable its ODT. - PSU_DDRC_ODTMAP_RANK0_RD_ODT 0x0 - - Indicates which remote ODTs must be turned on during a write to rank 0. Each rank has a remote ODT (in the SDRAM) which can b - turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB, - etc. For each rank, set its bit to 1 to enable its ODT. - PSU_DDRC_ODTMAP_RANK0_WR_ODT 0x1 - - ODT/Rank Map Register - (OFFSET, MASK, VALUE) (0XFD070244, 0x00003333U ,0x00000001U) - RegMask = (DDRC_ODTMAP_RANK1_RD_ODT_MASK | DDRC_ODTMAP_RANK1_WR_ODT_MASK | DDRC_ODTMAP_RANK0_RD_ODT_MASK | DDRC_ODTMAP_RANK0_WR_ODT_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_ODTMAP_RANK1_RD_ODT_SHIFT - | 0x00000000U << DDRC_ODTMAP_RANK1_WR_ODT_SHIFT - | 0x00000000U << DDRC_ODTMAP_RANK0_RD_ODT_SHIFT - | 0x00000001U << DDRC_ODTMAP_RANK0_WR_ODT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_ODTMAP_OFFSET ,0x00003333U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : SCHED @ 0XFD070250</p> - - When the preferred transaction store is empty for these many clock cycles, switch to the alternate transaction store if it is - non-empty. The read transaction store (both high and low priority) is the default preferred transaction store and the write t - ansaction store is the alternative store. When prefer write over read is set this is reversed. 0x0 is a legal value for this - egister. When set to 0x0, the transaction store switching will happen immediately when the switching conditions become true. - OR PERFORMANCE ONLY - PSU_DDRC_SCHED_RDWR_IDLE_GAP 0x1 - - UNUSED - PSU_DDRC_SCHED_GO2CRITICAL_HYSTERESIS 0x0 - - Number of entries in the low priority transaction store is this value + 1. (MEMC_NO_OF_ENTRY - (SCHED.lpr_num_entries + 1)) i - the number of entries available for the high priority transaction store. Setting this to maximum value allocates all entries - to low priority transaction store. Setting this to 0 allocates 1 entry to low priority transaction store and the rest to high - priority transaction store. Note: In ECC configurations, the numbers of write and low priority read credits issued is one les - than in the non-ECC case. One entry each is reserved in the write and low-priority read CAMs for storing the RMW requests ar - sing out of single bit error correction RMW operation. - PSU_DDRC_SCHED_LPR_NUM_ENTRIES 0x20 - - If true, bank is kept open only while there are page hit transactions available in the CAM to that bank. The last read or wri - e command in the CAM with a bank and page hit will be executed with auto-precharge if SCHED1.pageclose_timer=0. Even if this - egister set to 1 and SCHED1.pageclose_timer is set to 0, explicit precharge (and not auto-precharge) may be issued in some ca - es where there is a mode switch between Write and Read or between LPR and HPR. The Read and Write commands that are executed - s part of the ECC scrub requests are also executed without auto-precharge. If false, the bank remains open until there is a n - ed to close it (to open a different page, or for page timeout or refresh timeout) - also known as open page policy. The open - age policy can be overridden by setting the per-command-autopre bit on the HIF interface (hif_cmd_autopre). The pageclose fea - ure provids a midway between Open and Close page policies. FOR PERFORMANCE ONLY. - PSU_DDRC_SCHED_PAGECLOSE 0x0 - - If set then the bank selector prefers writes over reads. FOR DEBUG ONLY. - PSU_DDRC_SCHED_PREFER_WRITE 0x0 - - Active low signal. When asserted ('0'), all incoming transactions are forced to low priority. This implies that all High Prio - ity Read (HPR) and Variable Priority Read commands (VPR) will be treated as Low Priority Read (LPR) commands. On the write si - e, all Variable Priority Write (VPW) commands will be treated as Normal Priority Write (NPW) commands. Forcing the incoming t - ansactions to low priority implicitly turns off Bypass path for read commands. FOR PERFORMANCE ONLY. - PSU_DDRC_SCHED_FORCE_LOW_PRI_N 0x1 - - Scheduler Control Register - (OFFSET, MASK, VALUE) (0XFD070250, 0x7FFF3F07U ,0x01002001U) - RegMask = (DDRC_SCHED_RDWR_IDLE_GAP_MASK | DDRC_SCHED_GO2CRITICAL_HYSTERESIS_MASK | DDRC_SCHED_LPR_NUM_ENTRIES_MASK | DDRC_SCHED_PAGECLOSE_MASK | DDRC_SCHED_PREFER_WRITE_MASK | DDRC_SCHED_FORCE_LOW_PRI_N_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_SCHED_RDWR_IDLE_GAP_SHIFT - | 0x00000000U << DDRC_SCHED_GO2CRITICAL_HYSTERESIS_SHIFT - | 0x00000020U << DDRC_SCHED_LPR_NUM_ENTRIES_SHIFT - | 0x00000000U << DDRC_SCHED_PAGECLOSE_SHIFT - | 0x00000000U << DDRC_SCHED_PREFER_WRITE_SHIFT - | 0x00000001U << DDRC_SCHED_FORCE_LOW_PRI_N_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_SCHED_OFFSET ,0x7FFF3F07U ,0x01002001U); - /*############################################################################################################################ */ - - /*Register : PERFLPR1 @ 0XFD070264</p> - - Number of transactions that are serviced once the LPR queue goes critical is the smaller of: - (a) This number - (b) Number o - transactions available. Unit: Transaction. FOR PERFORMANCE ONLY. - PSU_DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH 0x8 - - Number of clocks that the LPR queue can be starved before it goes critical. The minimum valid functional value for this regis - er is 0x1. Programming it to 0x0 will disable the starvation functionality; during normal operation, this function should not - be disabled as it will cause excessive latencies. Unit: Clock cycles. FOR PERFORMANCE ONLY. - PSU_DDRC_PERFLPR1_LPR_MAX_STARVE 0x40 - - Low Priority Read CAM Register 1 - (OFFSET, MASK, VALUE) (0XFD070264, 0xFF00FFFFU ,0x08000040U) - RegMask = (DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH_MASK | DDRC_PERFLPR1_LPR_MAX_STARVE_MASK | 0 ); - - RegVal = ((0x00000008U << DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH_SHIFT - | 0x00000040U << DDRC_PERFLPR1_LPR_MAX_STARVE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PERFLPR1_OFFSET ,0xFF00FFFFU ,0x08000040U); - /*############################################################################################################################ */ - - /*Register : PERFWR1 @ 0XFD07026C</p> - - Number of transactions that are serviced once the WR queue goes critical is the smaller of: - (a) This number - (b) Number of - transactions available. Unit: Transaction. FOR PERFORMANCE ONLY. - PSU_DDRC_PERFWR1_W_XACT_RUN_LENGTH 0x8 - - Number of clocks that the WR queue can be starved before it goes critical. The minimum valid functional value for this regist - r is 0x1. Programming it to 0x0 will disable the starvation functionality; during normal operation, this function should not - e disabled as it will cause excessive latencies. Unit: Clock cycles. FOR PERFORMANCE ONLY. - PSU_DDRC_PERFWR1_W_MAX_STARVE 0x40 - - Write CAM Register 1 - (OFFSET, MASK, VALUE) (0XFD07026C, 0xFF00FFFFU ,0x08000040U) - RegMask = (DDRC_PERFWR1_W_XACT_RUN_LENGTH_MASK | DDRC_PERFWR1_W_MAX_STARVE_MASK | 0 ); - - RegVal = ((0x00000008U << DDRC_PERFWR1_W_XACT_RUN_LENGTH_SHIFT - | 0x00000040U << DDRC_PERFWR1_W_MAX_STARVE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PERFWR1_OFFSET ,0xFF00FFFFU ,0x08000040U); - /*############################################################################################################################ */ - - /*Register : DQMAP5 @ 0XFD070294</p> - - All even ranks have the same DQ mapping controled by DQMAP0-4 register as rank 0. This register provides DQ swap function for - all odd ranks to support CRC feature. rank based DQ swapping is: swap bit 0 with 1, swap bit 2 with 3, swap bit 4 with 5 and - wap bit 6 with 7. 1: Disable rank based DQ swapping 0: Enable rank based DQ swapping Present only in designs configured to su - port DDR4. - PSU_DDRC_DQMAP5_DIS_DQ_RANK_SWAP 0x1 - - DQ Map Register 5 - (OFFSET, MASK, VALUE) (0XFD070294, 0x00000001U ,0x00000001U) - RegMask = (DDRC_DQMAP5_DIS_DQ_RANK_SWAP_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_DQMAP5_DIS_DQ_RANK_SWAP_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DQMAP5_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : DBG0 @ 0XFD070300</p> - - When this is set to '0', auto-precharge is disabled for the flushed command in a collision case. Collision cases are write fo - lowed by read to same address, read followed by write to same address, or write followed by write to same address with DBG0.d - s_wc bit = 1 (where same address comparisons exclude the two address bits representing critical word). FOR DEBUG ONLY. - PSU_DDRC_DBG0_DIS_COLLISION_PAGE_OPT 0x0 - - When 1, disable write combine. FOR DEBUG ONLY - PSU_DDRC_DBG0_DIS_WC 0x0 - - Debug Register 0 - (OFFSET, MASK, VALUE) (0XFD070300, 0x00000011U ,0x00000000U) - RegMask = (DDRC_DBG0_DIS_COLLISION_PAGE_OPT_MASK | DDRC_DBG0_DIS_WC_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_DBG0_DIS_COLLISION_PAGE_OPT_SHIFT - | 0x00000000U << DDRC_DBG0_DIS_WC_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DBG0_OFFSET ,0x00000011U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DBGCMD @ 0XFD07030C</p> - - Setting this register bit to 1 allows refresh and ZQCS commands to be triggered from hardware via the IOs ext_*. If set to 1, - the fields DBGCMD.zq_calib_short and DBGCMD.rank*_refresh have no function, and are ignored by the uMCTL2 logic. Setting this - register bit to 0 allows refresh and ZQCS to be triggered from software, via the fields DBGCMD.zq_calib_short and DBGCMD.rank - _refresh. If set to 0, the hardware pins ext_* have no function, and are ignored by the uMCTL2 logic. This register is static - and may only be changed when the DDRC reset signal, core_ddrc_rstn, is asserted (0). - PSU_DDRC_DBGCMD_HW_REF_ZQ_EN 0x0 - - Setting this register bit to 1 indicates to the uMCTL2 to issue a dfi_ctrlupd_req to the PHY. When this request is stored in - he uMCTL2, the bit is automatically cleared. This operation must only be performed when DFIUPD0.dis_auto_ctrlupd=1. - PSU_DDRC_DBGCMD_CTRLUPD 0x0 - - Setting this register bit to 1 indicates to the uMCTL2 to issue a ZQCS (ZQ calibration short)/MPC(ZQ calibration) command to - he SDRAM. When this request is stored in the uMCTL2, the bit is automatically cleared. This operation can be performed only w - en ZQCTL0.dis_auto_zq=1. It is recommended NOT to set this register bit if in Init operating mode. This register bit is ignor - d when in Self-Refresh(except LPDDR4) and SR-Powerdown(LPDDR4) and Deep power-down operating modes and Maximum Power Saving M - de. - PSU_DDRC_DBGCMD_ZQ_CALIB_SHORT 0x0 - - Setting this register bit to 1 indicates to the uMCTL2 to issue a refresh to rank 1. Writing to this bit causes DBGSTAT.rank1 - refresh_busy to be set. When DBGSTAT.rank1_refresh_busy is cleared, the command has been stored in uMCTL2. This operation can - be performed only when RFSHCTL3.dis_auto_refresh=1. It is recommended NOT to set this register bit if in Init or Deep power-d - wn operating modes or Maximum Power Saving Mode. - PSU_DDRC_DBGCMD_RANK1_REFRESH 0x0 - - Setting this register bit to 1 indicates to the uMCTL2 to issue a refresh to rank 0. Writing to this bit causes DBGSTAT.rank0 - refresh_busy to be set. When DBGSTAT.rank0_refresh_busy is cleared, the command has been stored in uMCTL2. This operation can - be performed only when RFSHCTL3.dis_auto_refresh=1. It is recommended NOT to set this register bit if in Init or Deep power-d - wn operating modes or Maximum Power Saving Mode. - PSU_DDRC_DBGCMD_RANK0_REFRESH 0x0 - - Command Debug Register - (OFFSET, MASK, VALUE) (0XFD07030C, 0x80000033U ,0x00000000U) - RegMask = (DDRC_DBGCMD_HW_REF_ZQ_EN_MASK | DDRC_DBGCMD_CTRLUPD_MASK | DDRC_DBGCMD_ZQ_CALIB_SHORT_MASK | DDRC_DBGCMD_RANK1_REFRESH_MASK | DDRC_DBGCMD_RANK0_REFRESH_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_DBGCMD_HW_REF_ZQ_EN_SHIFT - | 0x00000000U << DDRC_DBGCMD_CTRLUPD_SHIFT - | 0x00000000U << DDRC_DBGCMD_ZQ_CALIB_SHORT_SHIFT - | 0x00000000U << DDRC_DBGCMD_RANK1_REFRESH_SHIFT - | 0x00000000U << DDRC_DBGCMD_RANK0_REFRESH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DBGCMD_OFFSET ,0x80000033U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : SWCTL @ 0XFD070320</p> - - Enable quasi-dynamic register programming outside reset. Program register to 0 to enable quasi-dynamic programming. Set back - egister to 1 once programming is done. - PSU_DDRC_SWCTL_SW_DONE 0x0 - - Software register programming control enable - (OFFSET, MASK, VALUE) (0XFD070320, 0x00000001U ,0x00000000U) - RegMask = (DDRC_SWCTL_SW_DONE_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_SWCTL_SW_DONE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_SWCTL_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : PCCFG @ 0XFD070400</p> - - Burst length expansion mode. By default (i.e. bl_exp_mode==0) XPI expands every AXI burst into multiple HIF commands, using t - e memory burst length as a unit. If set to 1, then XPI will use half of the memory burst length as a unit. This applies to bo - h reads and writes. When MSTR.data_bus_width==00, setting bl_exp_mode to 1 has no effect. This can be used in cases where Par - ial Writes is enabled (UMCTL2_PARTIAL_WR=1) and DBG0.dis_wc=1, in order to avoid or minimize t_ccd_l penalty in DDR4 and t_cc - _mw penalty in LPDDR4. Note that if DBICTL.reg_ddrc_dm_en=0, functionality is not supported in the following cases: - UMCTL2_ - ARTIAL_WR=0 - UMCTL2_PARTIAL_WR=1, MSTR.reg_ddrc_data_bus_width=01, MEMC_BURST_LENGTH=8 and MSTR.reg_ddrc_burst_rdwr=1000 (LP - DR4 only) - UMCTL2_PARTIAL_WR=1, MSTR.reg_ddrc_data_bus_width=01, MEMC_BURST_LENGTH=4 and MSTR.reg_ddrc_burst_rdwr=0100 (DDR4 - only), with either MSTR.reg_ddrc_burstchop=0 or CRCPARCTL1.reg_ddrc_crc_enable=1 Functionality is also not supported if Share - -AC is enabled - PSU_DDRC_PCCFG_BL_EXP_MODE 0x0 - - Page match four limit. If set to 1, limits the number of consecutive same page DDRC transactions that can be granted by the P - rt Arbiter to four when Page Match feature is enabled. If set to 0, there is no limit imposed on number of consecutive same p - ge DDRC transactions. - PSU_DDRC_PCCFG_PAGEMATCH_LIMIT 0x0 - - If set to 1 (enabled), sets co_gs_go2critical_wr and co_gs_go2critical_lpr/co_gs_go2critical_hpr signals going to DDRC based - n urgent input (awurgent, arurgent) coming from AXI master. If set to 0 (disabled), co_gs_go2critical_wr and co_gs_go2critica - _lpr/co_gs_go2critical_hpr signals at DDRC are driven to 1b'0. - PSU_DDRC_PCCFG_GO2CRITICAL_EN 0x1 - - Port Common Configuration Register - (OFFSET, MASK, VALUE) (0XFD070400, 0x00000111U ,0x00000001U) - RegMask = (DDRC_PCCFG_BL_EXP_MODE_MASK | DDRC_PCCFG_PAGEMATCH_LIMIT_MASK | DDRC_PCCFG_GO2CRITICAL_EN_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCCFG_BL_EXP_MODE_SHIFT - | 0x00000000U << DDRC_PCCFG_PAGEMATCH_LIMIT_SHIFT - | 0x00000001U << DDRC_PCCFG_GO2CRITICAL_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCCFG_OFFSET ,0x00000111U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : PCFGR_0 @ 0XFD070404</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN 0x0 - - If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command). - PSU_DDRC_PCFGR_0_RD_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the read channel of the port. - PSU_DDRC_PCFGR_0_RD_PORT_AGING_EN 0x0 - - Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGR_0_RD_PORT_PRIORITY 0xf - - Port n Configuration Read Register - (OFFSET, MASK, VALUE) (0XFD070404, 0x000073FFU ,0x0000200FU) - RegMask = (DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGR_0_RD_PORT_URGENT_EN_MASK | DDRC_PCFGR_0_RD_PORT_AGING_EN_MASK | DDRC_PCFGR_0_RD_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGR_0_RD_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGR_0_RD_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGR_0_RD_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGR_0_OFFSET ,0x000073FFU ,0x0000200FU); - /*############################################################################################################################ */ - - /*Register : PCFGW_0 @ 0XFD070408</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN 0x1 - - If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command). - PSU_DDRC_PCFGW_0_WR_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the write channel of the port. - PSU_DDRC_PCFGW_0_WR_PORT_AGING_EN 0x0 - - Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGW_0_WR_PORT_PRIORITY 0xf - - Port n Configuration Write Register - (OFFSET, MASK, VALUE) (0XFD070408, 0x000073FFU ,0x0000600FU) - RegMask = (DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGW_0_WR_PORT_URGENT_EN_MASK | DDRC_PCFGW_0_WR_PORT_AGING_EN_MASK | DDRC_PCFGW_0_WR_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGW_0_WR_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGW_0_WR_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGW_0_WR_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGW_0_OFFSET ,0x000073FFU ,0x0000600FU); - /*############################################################################################################################ */ - - /*Register : PCTRL_0 @ 0XFD070490</p> - - Enables port n. - PSU_DDRC_PCTRL_0_PORT_EN 0x1 - - Port n Control Register - (OFFSET, MASK, VALUE) (0XFD070490, 0x00000001U ,0x00000001U) - RegMask = (DDRC_PCTRL_0_PORT_EN_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCTRL_0_PORT_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCTRL_0_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS0_0 @ 0XFD070494</p> - - This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_0_RQOS_MAP_REGION1 0x2 - - This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_0_RQOS_MAP_REGION0 0x0 - - Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values. - PSU_DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1 0xb - - Port n Read QoS Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD070494, 0x0033000FU ,0x0020000BU) - RegMask = (DDRC_PCFGQOS0_0_RQOS_MAP_REGION1_MASK | DDRC_PCFGQOS0_0_RQOS_MAP_REGION0_MASK | DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1_MASK | 0 ); - - RegVal = ((0x00000002U << DDRC_PCFGQOS0_0_RQOS_MAP_REGION1_SHIFT - | 0x00000000U << DDRC_PCFGQOS0_0_RQOS_MAP_REGION0_SHIFT - | 0x0000000BU << DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS0_0_OFFSET ,0x0033000FU ,0x0020000BU); - /*############################################################################################################################ */ - - /*Register : PCFGQOS1_0 @ 0XFD070498</p> - - Specifies the timeout value for transactions mapped to the red address queue. - PSU_DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR 0x0 - - Specifies the timeout value for transactions mapped to the blue address queue. - PSU_DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB 0x0 - - Port n Read QoS Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD070498, 0x07FF07FFU ,0x00000000U) - RegMask = (DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR_MASK | DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR_SHIFT - | 0x00000000U << DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS1_0_OFFSET ,0x07FF07FFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : PCFGR_1 @ 0XFD0704B4</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN 0x0 - - If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command). - PSU_DDRC_PCFGR_1_RD_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the read channel of the port. - PSU_DDRC_PCFGR_1_RD_PORT_AGING_EN 0x0 - - Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGR_1_RD_PORT_PRIORITY 0xf - - Port n Configuration Read Register - (OFFSET, MASK, VALUE) (0XFD0704B4, 0x000073FFU ,0x0000200FU) - RegMask = (DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGR_1_RD_PORT_URGENT_EN_MASK | DDRC_PCFGR_1_RD_PORT_AGING_EN_MASK | DDRC_PCFGR_1_RD_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGR_1_RD_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGR_1_RD_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGR_1_RD_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGR_1_OFFSET ,0x000073FFU ,0x0000200FU); - /*############################################################################################################################ */ - - /*Register : PCFGW_1 @ 0XFD0704B8</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN 0x1 - - If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command). - PSU_DDRC_PCFGW_1_WR_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the write channel of the port. - PSU_DDRC_PCFGW_1_WR_PORT_AGING_EN 0x0 - - Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGW_1_WR_PORT_PRIORITY 0xf - - Port n Configuration Write Register - (OFFSET, MASK, VALUE) (0XFD0704B8, 0x000073FFU ,0x0000600FU) - RegMask = (DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGW_1_WR_PORT_URGENT_EN_MASK | DDRC_PCFGW_1_WR_PORT_AGING_EN_MASK | DDRC_PCFGW_1_WR_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGW_1_WR_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGW_1_WR_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGW_1_WR_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGW_1_OFFSET ,0x000073FFU ,0x0000600FU); - /*############################################################################################################################ */ - - /*Register : PCTRL_1 @ 0XFD070540</p> - - Enables port n. - PSU_DDRC_PCTRL_1_PORT_EN 0x1 - - Port n Control Register - (OFFSET, MASK, VALUE) (0XFD070540, 0x00000001U ,0x00000001U) - RegMask = (DDRC_PCTRL_1_PORT_EN_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCTRL_1_PORT_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCTRL_1_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS0_1 @ 0XFD070544</p> - - This bitfield indicates the traffic class of region2. For dual address queue configurations, region2 maps to the red address - ueue. Valid values are 1: VPR and 2: HPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and traffic class of region2 - s set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_1_RQOS_MAP_REGION2 0x2 - - This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_1_RQOS_MAP_REGION1 0x0 - - This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_1_RQOS_MAP_REGION0 0x0 - - Separation level2 indicating the end of region1 mapping; start of region1 is (level1 + 1). Possible values for level2 are (le - el1 + 1) to 14 which corresponds to arqos. Region2 starts from (level2 + 1) up to 15. Note that for PA, arqos values are used - directly as port priorities, where the higher the value corresponds to higher port priority. All of the map_level* registers - ust be set to distinct values. - PSU_DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2 0xb - - Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values. - PSU_DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1 0x3 - - Port n Read QoS Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD070544, 0x03330F0FU ,0x02000B03U) - RegMask = (DDRC_PCFGQOS0_1_RQOS_MAP_REGION2_MASK | DDRC_PCFGQOS0_1_RQOS_MAP_REGION1_MASK | DDRC_PCFGQOS0_1_RQOS_MAP_REGION0_MASK | DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2_MASK | DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1_MASK | 0 ); - - RegVal = ((0x00000002U << DDRC_PCFGQOS0_1_RQOS_MAP_REGION2_SHIFT - | 0x00000000U << DDRC_PCFGQOS0_1_RQOS_MAP_REGION1_SHIFT - | 0x00000000U << DDRC_PCFGQOS0_1_RQOS_MAP_REGION0_SHIFT - | 0x0000000BU << DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2_SHIFT - | 0x00000003U << DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS0_1_OFFSET ,0x03330F0FU ,0x02000B03U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS1_1 @ 0XFD070548</p> - - Specifies the timeout value for transactions mapped to the red address queue. - PSU_DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR 0x0 - - Specifies the timeout value for transactions mapped to the blue address queue. - PSU_DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB 0x0 - - Port n Read QoS Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD070548, 0x07FF07FFU ,0x00000000U) - RegMask = (DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR_MASK | DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR_SHIFT - | 0x00000000U << DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS1_1_OFFSET ,0x07FF07FFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : PCFGR_2 @ 0XFD070564</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN 0x0 - - If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command). - PSU_DDRC_PCFGR_2_RD_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the read channel of the port. - PSU_DDRC_PCFGR_2_RD_PORT_AGING_EN 0x0 - - Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGR_2_RD_PORT_PRIORITY 0xf - - Port n Configuration Read Register - (OFFSET, MASK, VALUE) (0XFD070564, 0x000073FFU ,0x0000200FU) - RegMask = (DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGR_2_RD_PORT_URGENT_EN_MASK | DDRC_PCFGR_2_RD_PORT_AGING_EN_MASK | DDRC_PCFGR_2_RD_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGR_2_RD_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGR_2_RD_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGR_2_RD_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGR_2_OFFSET ,0x000073FFU ,0x0000200FU); - /*############################################################################################################################ */ - - /*Register : PCFGW_2 @ 0XFD070568</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN 0x1 - - If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command). - PSU_DDRC_PCFGW_2_WR_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the write channel of the port. - PSU_DDRC_PCFGW_2_WR_PORT_AGING_EN 0x0 - - Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGW_2_WR_PORT_PRIORITY 0xf - - Port n Configuration Write Register - (OFFSET, MASK, VALUE) (0XFD070568, 0x000073FFU ,0x0000600FU) - RegMask = (DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGW_2_WR_PORT_URGENT_EN_MASK | DDRC_PCFGW_2_WR_PORT_AGING_EN_MASK | DDRC_PCFGW_2_WR_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGW_2_WR_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGW_2_WR_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGW_2_WR_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGW_2_OFFSET ,0x000073FFU ,0x0000600FU); - /*############################################################################################################################ */ - - /*Register : PCTRL_2 @ 0XFD0705F0</p> - - Enables port n. - PSU_DDRC_PCTRL_2_PORT_EN 0x1 - - Port n Control Register - (OFFSET, MASK, VALUE) (0XFD0705F0, 0x00000001U ,0x00000001U) - RegMask = (DDRC_PCTRL_2_PORT_EN_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCTRL_2_PORT_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCTRL_2_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS0_2 @ 0XFD0705F4</p> - - This bitfield indicates the traffic class of region2. For dual address queue configurations, region2 maps to the red address - ueue. Valid values are 1: VPR and 2: HPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and traffic class of region2 - s set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_2_RQOS_MAP_REGION2 0x2 - - This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_2_RQOS_MAP_REGION1 0x0 - - This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_2_RQOS_MAP_REGION0 0x0 - - Separation level2 indicating the end of region1 mapping; start of region1 is (level1 + 1). Possible values for level2 are (le - el1 + 1) to 14 which corresponds to arqos. Region2 starts from (level2 + 1) up to 15. Note that for PA, arqos values are used - directly as port priorities, where the higher the value corresponds to higher port priority. All of the map_level* registers - ust be set to distinct values. - PSU_DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2 0xb - - Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values. - PSU_DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1 0x3 - - Port n Read QoS Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD0705F4, 0x03330F0FU ,0x02000B03U) - RegMask = (DDRC_PCFGQOS0_2_RQOS_MAP_REGION2_MASK | DDRC_PCFGQOS0_2_RQOS_MAP_REGION1_MASK | DDRC_PCFGQOS0_2_RQOS_MAP_REGION0_MASK | DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2_MASK | DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1_MASK | 0 ); - - RegVal = ((0x00000002U << DDRC_PCFGQOS0_2_RQOS_MAP_REGION2_SHIFT - | 0x00000000U << DDRC_PCFGQOS0_2_RQOS_MAP_REGION1_SHIFT - | 0x00000000U << DDRC_PCFGQOS0_2_RQOS_MAP_REGION0_SHIFT - | 0x0000000BU << DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2_SHIFT - | 0x00000003U << DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS0_2_OFFSET ,0x03330F0FU ,0x02000B03U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS1_2 @ 0XFD0705F8</p> - - Specifies the timeout value for transactions mapped to the red address queue. - PSU_DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR 0x0 - - Specifies the timeout value for transactions mapped to the blue address queue. - PSU_DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB 0x0 - - Port n Read QoS Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD0705F8, 0x07FF07FFU ,0x00000000U) - RegMask = (DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR_MASK | DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR_SHIFT - | 0x00000000U << DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS1_2_OFFSET ,0x07FF07FFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : PCFGR_3 @ 0XFD070614</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN 0x0 - - If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command). - PSU_DDRC_PCFGR_3_RD_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the read channel of the port. - PSU_DDRC_PCFGR_3_RD_PORT_AGING_EN 0x0 - - Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGR_3_RD_PORT_PRIORITY 0xf - - Port n Configuration Read Register - (OFFSET, MASK, VALUE) (0XFD070614, 0x000073FFU ,0x0000200FU) - RegMask = (DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGR_3_RD_PORT_URGENT_EN_MASK | DDRC_PCFGR_3_RD_PORT_AGING_EN_MASK | DDRC_PCFGR_3_RD_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGR_3_RD_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGR_3_RD_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGR_3_RD_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGR_3_OFFSET ,0x000073FFU ,0x0000200FU); - /*############################################################################################################################ */ - - /*Register : PCFGW_3 @ 0XFD070618</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN 0x1 - - If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command). - PSU_DDRC_PCFGW_3_WR_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the write channel of the port. - PSU_DDRC_PCFGW_3_WR_PORT_AGING_EN 0x0 - - Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGW_3_WR_PORT_PRIORITY 0xf - - Port n Configuration Write Register - (OFFSET, MASK, VALUE) (0XFD070618, 0x000073FFU ,0x0000600FU) - RegMask = (DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGW_3_WR_PORT_URGENT_EN_MASK | DDRC_PCFGW_3_WR_PORT_AGING_EN_MASK | DDRC_PCFGW_3_WR_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGW_3_WR_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGW_3_WR_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGW_3_WR_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGW_3_OFFSET ,0x000073FFU ,0x0000600FU); - /*############################################################################################################################ */ - - /*Register : PCTRL_3 @ 0XFD0706A0</p> - - Enables port n. - PSU_DDRC_PCTRL_3_PORT_EN 0x1 - - Port n Control Register - (OFFSET, MASK, VALUE) (0XFD0706A0, 0x00000001U ,0x00000001U) - RegMask = (DDRC_PCTRL_3_PORT_EN_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCTRL_3_PORT_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCTRL_3_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS0_3 @ 0XFD0706A4</p> - - This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_3_RQOS_MAP_REGION1 0x1 - - This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_3_RQOS_MAP_REGION0 0x0 - - Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values. - PSU_DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1 0x3 - - Port n Read QoS Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD0706A4, 0x0033000FU ,0x00100003U) - RegMask = (DDRC_PCFGQOS0_3_RQOS_MAP_REGION1_MASK | DDRC_PCFGQOS0_3_RQOS_MAP_REGION0_MASK | DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGQOS0_3_RQOS_MAP_REGION1_SHIFT - | 0x00000000U << DDRC_PCFGQOS0_3_RQOS_MAP_REGION0_SHIFT - | 0x00000003U << DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS0_3_OFFSET ,0x0033000FU ,0x00100003U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS1_3 @ 0XFD0706A8</p> - - Specifies the timeout value for transactions mapped to the red address queue. - PSU_DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR 0x0 - - Specifies the timeout value for transactions mapped to the blue address queue. - PSU_DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB 0x4f - - Port n Read QoS Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD0706A8, 0x07FF07FFU ,0x0000004FU) - RegMask = (DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR_MASK | DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR_SHIFT - | 0x0000004FU << DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS1_3_OFFSET ,0x07FF07FFU ,0x0000004FU); - /*############################################################################################################################ */ - - /*Register : PCFGWQOS0_3 @ 0XFD0706AC</p> - - This bitfield indicates the traffic class of region 1. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW traffic. - PSU_DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1 0x1 - - This bitfield indicates the traffic class of region 0. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW traffic. - PSU_DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0 0x0 - - Separation level indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 14 which c - rresponds to awqos. Note that for PA, awqos values are used directly as port priorities, where the higher the value correspon - s to higher port priority. - PSU_DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL 0x3 - - Port n Write QoS Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD0706AC, 0x0033000FU ,0x00100003U) - RegMask = (DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1_MASK | DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0_MASK | DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1_SHIFT - | 0x00000000U << DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0_SHIFT - | 0x00000003U << DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGWQOS0_3_OFFSET ,0x0033000FU ,0x00100003U); - /*############################################################################################################################ */ - - /*Register : PCFGWQOS1_3 @ 0XFD0706B0</p> - - Specifies the timeout value for write transactions. - PSU_DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT 0x4f - - Port n Write QoS Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD0706B0, 0x000007FFU ,0x0000004FU) - RegMask = (DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT_MASK | 0 ); - - RegVal = ((0x0000004FU << DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGWQOS1_3_OFFSET ,0x000007FFU ,0x0000004FU); - /*############################################################################################################################ */ - - /*Register : PCFGR_4 @ 0XFD0706C4</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN 0x1 - - If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command). - PSU_DDRC_PCFGR_4_RD_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the read channel of the port. - PSU_DDRC_PCFGR_4_RD_PORT_AGING_EN 0x0 - - Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGR_4_RD_PORT_PRIORITY 0xf - - Port n Configuration Read Register - (OFFSET, MASK, VALUE) (0XFD0706C4, 0x000073FFU ,0x0000600FU) - RegMask = (DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGR_4_RD_PORT_URGENT_EN_MASK | DDRC_PCFGR_4_RD_PORT_AGING_EN_MASK | DDRC_PCFGR_4_RD_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGR_4_RD_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGR_4_RD_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGR_4_RD_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGR_4_OFFSET ,0x000073FFU ,0x0000600FU); - /*############################################################################################################################ */ - - /*Register : PCFGW_4 @ 0XFD0706C8</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN 0x1 - - If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command). - PSU_DDRC_PCFGW_4_WR_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the write channel of the port. - PSU_DDRC_PCFGW_4_WR_PORT_AGING_EN 0x0 - - Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGW_4_WR_PORT_PRIORITY 0xf - - Port n Configuration Write Register - (OFFSET, MASK, VALUE) (0XFD0706C8, 0x000073FFU ,0x0000600FU) - RegMask = (DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGW_4_WR_PORT_URGENT_EN_MASK | DDRC_PCFGW_4_WR_PORT_AGING_EN_MASK | DDRC_PCFGW_4_WR_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGW_4_WR_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGW_4_WR_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGW_4_WR_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGW_4_OFFSET ,0x000073FFU ,0x0000600FU); - /*############################################################################################################################ */ - - /*Register : PCTRL_4 @ 0XFD070750</p> - - Enables port n. - PSU_DDRC_PCTRL_4_PORT_EN 0x1 - - Port n Control Register - (OFFSET, MASK, VALUE) (0XFD070750, 0x00000001U ,0x00000001U) - RegMask = (DDRC_PCTRL_4_PORT_EN_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCTRL_4_PORT_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCTRL_4_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS0_4 @ 0XFD070754</p> - - This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_4_RQOS_MAP_REGION1 0x1 - - This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_4_RQOS_MAP_REGION0 0x0 - - Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values. - PSU_DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1 0x3 - - Port n Read QoS Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD070754, 0x0033000FU ,0x00100003U) - RegMask = (DDRC_PCFGQOS0_4_RQOS_MAP_REGION1_MASK | DDRC_PCFGQOS0_4_RQOS_MAP_REGION0_MASK | DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGQOS0_4_RQOS_MAP_REGION1_SHIFT - | 0x00000000U << DDRC_PCFGQOS0_4_RQOS_MAP_REGION0_SHIFT - | 0x00000003U << DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS0_4_OFFSET ,0x0033000FU ,0x00100003U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS1_4 @ 0XFD070758</p> - - Specifies the timeout value for transactions mapped to the red address queue. - PSU_DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR 0x0 - - Specifies the timeout value for transactions mapped to the blue address queue. - PSU_DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB 0x4f - - Port n Read QoS Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD070758, 0x07FF07FFU ,0x0000004FU) - RegMask = (DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR_MASK | DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR_SHIFT - | 0x0000004FU << DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS1_4_OFFSET ,0x07FF07FFU ,0x0000004FU); - /*############################################################################################################################ */ - - /*Register : PCFGWQOS0_4 @ 0XFD07075C</p> - - This bitfield indicates the traffic class of region 1. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW traffic. - PSU_DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1 0x1 - - This bitfield indicates the traffic class of region 0. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW traffic. - PSU_DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0 0x0 - - Separation level indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 14 which c - rresponds to awqos. Note that for PA, awqos values are used directly as port priorities, where the higher the value correspon - s to higher port priority. - PSU_DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL 0x3 - - Port n Write QoS Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD07075C, 0x0033000FU ,0x00100003U) - RegMask = (DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1_MASK | DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0_MASK | DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1_SHIFT - | 0x00000000U << DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0_SHIFT - | 0x00000003U << DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGWQOS0_4_OFFSET ,0x0033000FU ,0x00100003U); - /*############################################################################################################################ */ - - /*Register : PCFGWQOS1_4 @ 0XFD070760</p> - - Specifies the timeout value for write transactions. - PSU_DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT 0x4f - - Port n Write QoS Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD070760, 0x000007FFU ,0x0000004FU) - RegMask = (DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT_MASK | 0 ); - - RegVal = ((0x0000004FU << DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGWQOS1_4_OFFSET ,0x000007FFU ,0x0000004FU); - /*############################################################################################################################ */ - - /*Register : PCFGR_5 @ 0XFD070774</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN 0x0 - - If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command). - PSU_DDRC_PCFGR_5_RD_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the read channel of the port. - PSU_DDRC_PCFGR_5_RD_PORT_AGING_EN 0x0 - - Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGR_5_RD_PORT_PRIORITY 0xf - - Port n Configuration Read Register - (OFFSET, MASK, VALUE) (0XFD070774, 0x000073FFU ,0x0000200FU) - RegMask = (DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGR_5_RD_PORT_URGENT_EN_MASK | DDRC_PCFGR_5_RD_PORT_AGING_EN_MASK | DDRC_PCFGR_5_RD_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGR_5_RD_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGR_5_RD_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGR_5_RD_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGR_5_OFFSET ,0x000073FFU ,0x0000200FU); - /*############################################################################################################################ */ - - /*Register : PCFGW_5 @ 0XFD070778</p> - - If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register. - PSU_DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN 0x1 - - If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command). - PSU_DDRC_PCFGW_5_WR_PORT_URGENT_EN 0x1 - - If set to 1, enables aging function for the write channel of the port. - PSU_DDRC_PCFGW_5_WR_PORT_AGING_EN 0x0 - - Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00. - PSU_DDRC_PCFGW_5_WR_PORT_PRIORITY 0xf - - Port n Configuration Write Register - (OFFSET, MASK, VALUE) (0XFD070778, 0x000073FFU ,0x0000600FU) - RegMask = (DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN_MASK | DDRC_PCFGW_5_WR_PORT_URGENT_EN_MASK | DDRC_PCFGW_5_WR_PORT_AGING_EN_MASK | DDRC_PCFGW_5_WR_PORT_PRIORITY_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN_SHIFT - | 0x00000001U << DDRC_PCFGW_5_WR_PORT_URGENT_EN_SHIFT - | 0x00000000U << DDRC_PCFGW_5_WR_PORT_AGING_EN_SHIFT - | 0x0000000FU << DDRC_PCFGW_5_WR_PORT_PRIORITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGW_5_OFFSET ,0x000073FFU ,0x0000600FU); - /*############################################################################################################################ */ - - /*Register : PCTRL_5 @ 0XFD070800</p> - - Enables port n. - PSU_DDRC_PCTRL_5_PORT_EN 0x1 - - Port n Control Register - (OFFSET, MASK, VALUE) (0XFD070800, 0x00000001U ,0x00000001U) - RegMask = (DDRC_PCTRL_5_PORT_EN_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCTRL_5_PORT_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCTRL_5_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS0_5 @ 0XFD070804</p> - - This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_5_RQOS_MAP_REGION1 0x1 - - This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic. - PSU_DDRC_PCFGQOS0_5_RQOS_MAP_REGION0 0x0 - - Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values. - PSU_DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1 0x3 - - Port n Read QoS Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD070804, 0x0033000FU ,0x00100003U) - RegMask = (DDRC_PCFGQOS0_5_RQOS_MAP_REGION1_MASK | DDRC_PCFGQOS0_5_RQOS_MAP_REGION0_MASK | DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGQOS0_5_RQOS_MAP_REGION1_SHIFT - | 0x00000000U << DDRC_PCFGQOS0_5_RQOS_MAP_REGION0_SHIFT - | 0x00000003U << DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS0_5_OFFSET ,0x0033000FU ,0x00100003U); - /*############################################################################################################################ */ - - /*Register : PCFGQOS1_5 @ 0XFD070808</p> - - Specifies the timeout value for transactions mapped to the red address queue. - PSU_DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR 0x0 - - Specifies the timeout value for transactions mapped to the blue address queue. - PSU_DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB 0x4f - - Port n Read QoS Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD070808, 0x07FF07FFU ,0x0000004FU) - RegMask = (DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR_MASK | DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR_SHIFT - | 0x0000004FU << DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGQOS1_5_OFFSET ,0x07FF07FFU ,0x0000004FU); - /*############################################################################################################################ */ - - /*Register : PCFGWQOS0_5 @ 0XFD07080C</p> - - This bitfield indicates the traffic class of region 1. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW traffic. - PSU_DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1 0x1 - - This bitfield indicates the traffic class of region 0. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW traffic. - PSU_DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0 0x0 - - Separation level indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 14 which c - rresponds to awqos. Note that for PA, awqos values are used directly as port priorities, where the higher the value correspon - s to higher port priority. - PSU_DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL 0x3 - - Port n Write QoS Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD07080C, 0x0033000FU ,0x00100003U) - RegMask = (DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1_MASK | DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0_MASK | DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL_MASK | 0 ); - - RegVal = ((0x00000001U << DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1_SHIFT - | 0x00000000U << DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0_SHIFT - | 0x00000003U << DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGWQOS0_5_OFFSET ,0x0033000FU ,0x00100003U); - /*############################################################################################################################ */ - - /*Register : PCFGWQOS1_5 @ 0XFD070810</p> - - Specifies the timeout value for write transactions. - PSU_DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT 0x4f - - Port n Write QoS Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD070810, 0x000007FFU ,0x0000004FU) - RegMask = (DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT_MASK | 0 ); - - RegVal = ((0x0000004FU << DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_PCFGWQOS1_5_OFFSET ,0x000007FFU ,0x0000004FU); - /*############################################################################################################################ */ - - /*Register : SARBASE0 @ 0XFD070F04</p> - - Base address for address region n specified as awaddr[UMCTL2_A_ADDRW-1:x] and araddr[UMCTL2_A_ADDRW-1:x] where x is determine - by the minimum block size parameter UMCTL2_SARMINSIZE: (x=log2(block size)). - PSU_DDRC_SARBASE0_BASE_ADDR 0x0 - - SAR Base Address Register n - (OFFSET, MASK, VALUE) (0XFD070F04, 0x000001FFU ,0x00000000U) - RegMask = (DDRC_SARBASE0_BASE_ADDR_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_SARBASE0_BASE_ADDR_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_SARBASE0_OFFSET ,0x000001FFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : SARSIZE0 @ 0XFD070F08</p> - - Number of blocks for address region n. This register determines the total size of the region in multiples of minimum block si - e as specified by the hardware parameter UMCTL2_SARMINSIZE. The register value is encoded as number of blocks = nblocks + 1. - or example, if register is programmed to 0, region will have 1 block. - PSU_DDRC_SARSIZE0_NBLOCKS 0x0 - - SAR Size Register n - (OFFSET, MASK, VALUE) (0XFD070F08, 0x000000FFU ,0x00000000U) - RegMask = (DDRC_SARSIZE0_NBLOCKS_MASK | 0 ); - - RegVal = ((0x00000000U << DDRC_SARSIZE0_NBLOCKS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_SARSIZE0_OFFSET ,0x000000FFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : SARBASE1 @ 0XFD070F0C</p> - - Base address for address region n specified as awaddr[UMCTL2_A_ADDRW-1:x] and araddr[UMCTL2_A_ADDRW-1:x] where x is determine - by the minimum block size parameter UMCTL2_SARMINSIZE: (x=log2(block size)). - PSU_DDRC_SARBASE1_BASE_ADDR 0x10 - - SAR Base Address Register n - (OFFSET, MASK, VALUE) (0XFD070F0C, 0x000001FFU ,0x00000010U) - RegMask = (DDRC_SARBASE1_BASE_ADDR_MASK | 0 ); - - RegVal = ((0x00000010U << DDRC_SARBASE1_BASE_ADDR_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_SARBASE1_OFFSET ,0x000001FFU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : SARSIZE1 @ 0XFD070F10</p> - - Number of blocks for address region n. This register determines the total size of the region in multiples of minimum block si - e as specified by the hardware parameter UMCTL2_SARMINSIZE. The register value is encoded as number of blocks = nblocks + 1. - or example, if register is programmed to 0, region will have 1 block. - PSU_DDRC_SARSIZE1_NBLOCKS 0xf - - SAR Size Register n - (OFFSET, MASK, VALUE) (0XFD070F10, 0x000000FFU ,0x0000000FU) - RegMask = (DDRC_SARSIZE1_NBLOCKS_MASK | 0 ); - - RegVal = ((0x0000000FU << DDRC_SARSIZE1_NBLOCKS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_SARSIZE1_OFFSET ,0x000000FFU ,0x0000000FU); - /*############################################################################################################################ */ - - /*Register : DFITMG0_SHADOW @ 0XFD072190</p> - - Specifies the number of DFI clock cycles after an assertion or de-assertion of the DFI control signals that the control signa - s at the PHY-DRAM interface reflect the assertion or de-assertion. If the DFI clock and the memory clock are not phase-aligne - , this timing parameter should be rounded up to the next integer value. Note that if using RDIMM, it is necessary to incremen - this parameter by RDIMM's extra cycle of latency in terms of DFI clock. - PSU_DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY 0x7 - - Defines whether dfi_rddata_en/dfi_rddata/dfi_rddata_valid is generated using HDR or SDR values Selects whether value in DFITM - 0.dfi_t_rddata_en is in terms of SDR or HDR clock cycles: - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles R - fer to PHY specification for correct value. - PSU_DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR 0x1 - - Time from the assertion of a read command on the DFI interface to the assertion of the dfi_rddata_en signal. Refer to PHY spe - ification for correct value. This corresponds to the DFI parameter trddata_en. Note that, depending on the PHY, if using RDIM - , it may be necessary to use the value (CL + 1) in the calculation of trddata_en. This is to compensate for the extra cycle o - latency through the RDIMM. Unit: Clocks - PSU_DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN 0x2 - - Defines whether dfi_wrdata_en/dfi_wrdata/dfi_wrdata_mask is generated using HDR or SDR values Selects whether value in DFITMG - .dfi_tphy_wrlat is in terms of SDR or HDR clock cycles Selects whether value in DFITMG0.dfi_tphy_wrdata is in terms of SDR or - HDR clock cycles - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles Refer to PHY specification for correct val - e. - PSU_DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR 0x1 - - Specifies the number of clock cycles between when dfi_wrdata_en is asserted to when the associated write data is driven on th - dfi_wrdata signal. This corresponds to the DFI timing parameter tphy_wrdata. Refer to PHY specification for correct value. N - te, max supported value is 8. Unit: Clocks - PSU_DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA 0x0 - - Write latency Number of clocks from the write command to write data enable (dfi_wrdata_en). This corresponds to the DFI timin - parameter tphy_wrlat. Refer to PHY specification for correct value.Note that, depending on the PHY, if using RDIMM, it may b - necessary to use the value (CL + 1) in the calculation of tphy_wrlat. This is to compensate for the extra cycle of latency t - rough the RDIMM. - PSU_DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT 0x2 - - DFI Timing Shadow Register 0 - (OFFSET, MASK, VALUE) (0XFD072190, 0x1FBFBF3FU ,0x07828002U) - RegMask = (DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY_MASK | DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR_MASK | DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN_MASK | DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR_MASK | DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA_MASK | DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT_MASK | 0 ); - - RegVal = ((0x00000007U << DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY_SHIFT - | 0x00000001U << DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR_SHIFT - | 0x00000002U << DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN_SHIFT - | 0x00000001U << DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR_SHIFT - | 0x00000000U << DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA_SHIFT - | 0x00000002U << DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDRC_DFITMG0_SHADOW_OFFSET ,0x1FBFBF3FU ,0x07828002U); - /*############################################################################################################################ */ - - // : DDR CONTROLLER RESET - /*Register : RST_DDR_SS @ 0XFD1A0108</p> - - DDR block level reset inside of the DDR Sub System - PSU_CRF_APB_RST_DDR_SS_DDR_RESET 0X0 - - DDR sub system block level reset - (OFFSET, MASK, VALUE) (0XFD1A0108, 0x00000008U ,0x00000000U) - RegMask = (CRF_APB_RST_DDR_SS_DDR_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_RST_DDR_SS_DDR_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_RST_DDR_SS_OFFSET ,0x00000008U ,0x00000000U); - /*############################################################################################################################ */ - - // : DDR PHY - /*Register : PGCR0 @ 0XFD080010</p> - - Address Copy - PSU_DDR_PHY_PGCR0_ADCP 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_PGCR0_RESERVED_30_27 0x0 - - PHY FIFO Reset - PSU_DDR_PHY_PGCR0_PHYFRST 0x1 - - Oscillator Mode Address/Command Delay Line Select - PSU_DDR_PHY_PGCR0_OSCACDL 0x3 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_PGCR0_RESERVED_23_19 0x0 - - Digital Test Output Select - PSU_DDR_PHY_PGCR0_DTOSEL 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_PGCR0_RESERVED_13 0x0 - - Oscillator Mode Division - PSU_DDR_PHY_PGCR0_OSCDIV 0xf - - Oscillator Enable - PSU_DDR_PHY_PGCR0_OSCEN 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_PGCR0_RESERVED_7_0 0x0 - - PHY General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080010, 0xFFFFFFFFU ,0x07001E00U) - RegMask = (DDR_PHY_PGCR0_ADCP_MASK | DDR_PHY_PGCR0_RESERVED_30_27_MASK | DDR_PHY_PGCR0_PHYFRST_MASK | DDR_PHY_PGCR0_OSCACDL_MASK | DDR_PHY_PGCR0_RESERVED_23_19_MASK | DDR_PHY_PGCR0_DTOSEL_MASK | DDR_PHY_PGCR0_RESERVED_13_MASK | DDR_PHY_PGCR0_OSCDIV_MASK | DDR_PHY_PGCR0_OSCEN_MASK | DDR_PHY_PGCR0_RESERVED_7_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_PGCR0_ADCP_SHIFT - | 0x00000000U << DDR_PHY_PGCR0_RESERVED_30_27_SHIFT - | 0x00000001U << DDR_PHY_PGCR0_PHYFRST_SHIFT - | 0x00000003U << DDR_PHY_PGCR0_OSCACDL_SHIFT - | 0x00000000U << DDR_PHY_PGCR0_RESERVED_23_19_SHIFT - | 0x00000000U << DDR_PHY_PGCR0_DTOSEL_SHIFT - | 0x00000000U << DDR_PHY_PGCR0_RESERVED_13_SHIFT - | 0x0000000FU << DDR_PHY_PGCR0_OSCDIV_SHIFT - | 0x00000000U << DDR_PHY_PGCR0_OSCEN_SHIFT - | 0x00000000U << DDR_PHY_PGCR0_RESERVED_7_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_PGCR0_OFFSET ,0xFFFFFFFFU ,0x07001E00U); - /*############################################################################################################################ */ - - /*Register : PGCR2 @ 0XFD080018</p> - - Clear Training Status Registers - PSU_DDR_PHY_PGCR2_CLRTSTAT 0x0 - - Clear Impedance Calibration - PSU_DDR_PHY_PGCR2_CLRZCAL 0x0 - - Clear Parity Error - PSU_DDR_PHY_PGCR2_CLRPERR 0x0 - - Initialization Complete Pin Configuration - PSU_DDR_PHY_PGCR2_ICPC 0x0 - - Data Training PUB Mode Exit Timer - PSU_DDR_PHY_PGCR2_DTPMXTMR 0xf - - Initialization Bypass - PSU_DDR_PHY_PGCR2_INITFSMBYP 0x0 - - PLL FSM Bypass - PSU_DDR_PHY_PGCR2_PLLFSMBYP 0x0 - - Refresh Period - PSU_DDR_PHY_PGCR2_TREFPRD 0x10028 - - PHY General Configuration Register 2 - (OFFSET, MASK, VALUE) (0XFD080018, 0xFFFFFFFFU ,0x00F10028U) - RegMask = (DDR_PHY_PGCR2_CLRTSTAT_MASK | DDR_PHY_PGCR2_CLRZCAL_MASK | DDR_PHY_PGCR2_CLRPERR_MASK | DDR_PHY_PGCR2_ICPC_MASK | DDR_PHY_PGCR2_DTPMXTMR_MASK | DDR_PHY_PGCR2_INITFSMBYP_MASK | DDR_PHY_PGCR2_PLLFSMBYP_MASK | DDR_PHY_PGCR2_TREFPRD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_PGCR2_CLRTSTAT_SHIFT - | 0x00000000U << DDR_PHY_PGCR2_CLRZCAL_SHIFT - | 0x00000000U << DDR_PHY_PGCR2_CLRPERR_SHIFT - | 0x00000000U << DDR_PHY_PGCR2_ICPC_SHIFT - | 0x0000000FU << DDR_PHY_PGCR2_DTPMXTMR_SHIFT - | 0x00000000U << DDR_PHY_PGCR2_INITFSMBYP_SHIFT - | 0x00000000U << DDR_PHY_PGCR2_PLLFSMBYP_SHIFT - | 0x00010028U << DDR_PHY_PGCR2_TREFPRD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_PGCR2_OFFSET ,0xFFFFFFFFU ,0x00F10028U); - /*############################################################################################################################ */ - - /*Register : PGCR3 @ 0XFD08001C</p> - - CKN Enable - PSU_DDR_PHY_PGCR3_CKNEN 0x55 - - CK Enable - PSU_DDR_PHY_PGCR3_CKEN 0xaa - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_PGCR3_RESERVED_15 0x0 - - Enable Clock Gating for AC [0] ctl_rd_clk - PSU_DDR_PHY_PGCR3_GATEACRDCLK 0x2 - - Enable Clock Gating for AC [0] ddr_clk - PSU_DDR_PHY_PGCR3_GATEACDDRCLK 0x2 - - Enable Clock Gating for AC [0] ctl_clk - PSU_DDR_PHY_PGCR3_GATEACCTLCLK 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_PGCR3_RESERVED_8 0x0 - - Controls DDL Bypass Modes - PSU_DDR_PHY_PGCR3_DDLBYPMODE 0x2 - - IO Loop-Back Select - PSU_DDR_PHY_PGCR3_IOLB 0x0 - - AC Receive FIFO Read Mode - PSU_DDR_PHY_PGCR3_RDMODE 0x0 - - Read FIFO Reset Disable - PSU_DDR_PHY_PGCR3_DISRST 0x0 - - Clock Level when Clock Gating - PSU_DDR_PHY_PGCR3_CLKLEVEL 0x0 - - PHY General Configuration Register 3 - (OFFSET, MASK, VALUE) (0XFD08001C, 0xFFFFFFFFU ,0x55AA5480U) - RegMask = (DDR_PHY_PGCR3_CKNEN_MASK | DDR_PHY_PGCR3_CKEN_MASK | DDR_PHY_PGCR3_RESERVED_15_MASK | DDR_PHY_PGCR3_GATEACRDCLK_MASK | DDR_PHY_PGCR3_GATEACDDRCLK_MASK | DDR_PHY_PGCR3_GATEACCTLCLK_MASK | DDR_PHY_PGCR3_RESERVED_8_MASK | DDR_PHY_PGCR3_DDLBYPMODE_MASK | DDR_PHY_PGCR3_IOLB_MASK | DDR_PHY_PGCR3_RDMODE_MASK | DDR_PHY_PGCR3_DISRST_MASK | DDR_PHY_PGCR3_CLKLEVEL_MASK | 0 ); - - RegVal = ((0x00000055U << DDR_PHY_PGCR3_CKNEN_SHIFT - | 0x000000AAU << DDR_PHY_PGCR3_CKEN_SHIFT - | 0x00000000U << DDR_PHY_PGCR3_RESERVED_15_SHIFT - | 0x00000002U << DDR_PHY_PGCR3_GATEACRDCLK_SHIFT - | 0x00000002U << DDR_PHY_PGCR3_GATEACDDRCLK_SHIFT - | 0x00000002U << DDR_PHY_PGCR3_GATEACCTLCLK_SHIFT - | 0x00000000U << DDR_PHY_PGCR3_RESERVED_8_SHIFT - | 0x00000002U << DDR_PHY_PGCR3_DDLBYPMODE_SHIFT - | 0x00000000U << DDR_PHY_PGCR3_IOLB_SHIFT - | 0x00000000U << DDR_PHY_PGCR3_RDMODE_SHIFT - | 0x00000000U << DDR_PHY_PGCR3_DISRST_SHIFT - | 0x00000000U << DDR_PHY_PGCR3_CLKLEVEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_PGCR3_OFFSET ,0xFFFFFFFFU ,0x55AA5480U); - /*############################################################################################################################ */ - - /*Register : PGCR5 @ 0XFD080024</p> - - Frequency B Ratio Term - PSU_DDR_PHY_PGCR5_FRQBT 0x1 - - Frequency A Ratio Term - PSU_DDR_PHY_PGCR5_FRQAT 0x1 - - DFI Disconnect Time Period - PSU_DDR_PHY_PGCR5_DISCNPERIOD 0x0 - - Receiver bias core side control - PSU_DDR_PHY_PGCR5_VREF_RBCTRL 0xf - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_PGCR5_RESERVED_3 0x0 - - Internal VREF generator REFSEL ragne select - PSU_DDR_PHY_PGCR5_DXREFISELRANGE 0x1 - - DDL Page Read Write select - PSU_DDR_PHY_PGCR5_DDLPGACT 0x0 - - DDL Page Read Write select - PSU_DDR_PHY_PGCR5_DDLPGRW 0x0 - - PHY General Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD080024, 0xFFFFFFFFU ,0x010100F4U) - RegMask = (DDR_PHY_PGCR5_FRQBT_MASK | DDR_PHY_PGCR5_FRQAT_MASK | DDR_PHY_PGCR5_DISCNPERIOD_MASK | DDR_PHY_PGCR5_VREF_RBCTRL_MASK | DDR_PHY_PGCR5_RESERVED_3_MASK | DDR_PHY_PGCR5_DXREFISELRANGE_MASK | DDR_PHY_PGCR5_DDLPGACT_MASK | DDR_PHY_PGCR5_DDLPGRW_MASK | 0 ); - - RegVal = ((0x00000001U << DDR_PHY_PGCR5_FRQBT_SHIFT - | 0x00000001U << DDR_PHY_PGCR5_FRQAT_SHIFT - | 0x00000000U << DDR_PHY_PGCR5_DISCNPERIOD_SHIFT - | 0x0000000FU << DDR_PHY_PGCR5_VREF_RBCTRL_SHIFT - | 0x00000000U << DDR_PHY_PGCR5_RESERVED_3_SHIFT - | 0x00000001U << DDR_PHY_PGCR5_DXREFISELRANGE_SHIFT - | 0x00000000U << DDR_PHY_PGCR5_DDLPGACT_SHIFT - | 0x00000000U << DDR_PHY_PGCR5_DDLPGRW_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_PGCR5_OFFSET ,0xFFFFFFFFU ,0x010100F4U); - /*############################################################################################################################ */ - - /*Register : PTR0 @ 0XFD080040</p> - - PLL Power-Down Time - PSU_DDR_PHY_PTR0_TPLLPD 0x2f0 - - PLL Gear Shift Time - PSU_DDR_PHY_PTR0_TPLLGS 0x60 - - PHY Reset Time - PSU_DDR_PHY_PTR0_TPHYRST 0x10 - - PHY Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD080040, 0xFFFFFFFFU ,0x5E001810U) - RegMask = (DDR_PHY_PTR0_TPLLPD_MASK | DDR_PHY_PTR0_TPLLGS_MASK | DDR_PHY_PTR0_TPHYRST_MASK | 0 ); - - RegVal = ((0x000002F0U << DDR_PHY_PTR0_TPLLPD_SHIFT - | 0x00000060U << DDR_PHY_PTR0_TPLLGS_SHIFT - | 0x00000010U << DDR_PHY_PTR0_TPHYRST_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_PTR0_OFFSET ,0xFFFFFFFFU ,0x5E001810U); - /*############################################################################################################################ */ - - /*Register : PTR1 @ 0XFD080044</p> - - PLL Lock Time - PSU_DDR_PHY_PTR1_TPLLLOCK 0x80 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_PTR1_RESERVED_15_13 0x0 - - PLL Reset Time - PSU_DDR_PHY_PTR1_TPLLRST 0x5f0 - - PHY Timing Register 1 - (OFFSET, MASK, VALUE) (0XFD080044, 0xFFFFFFFFU ,0x008005F0U) - RegMask = (DDR_PHY_PTR1_TPLLLOCK_MASK | DDR_PHY_PTR1_RESERVED_15_13_MASK | DDR_PHY_PTR1_TPLLRST_MASK | 0 ); - - RegVal = ((0x00000080U << DDR_PHY_PTR1_TPLLLOCK_SHIFT - | 0x00000000U << DDR_PHY_PTR1_RESERVED_15_13_SHIFT - | 0x000005F0U << DDR_PHY_PTR1_TPLLRST_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_PTR1_OFFSET ,0xFFFFFFFFU ,0x008005F0U); - /*############################################################################################################################ */ - - /*Register : DSGCR @ 0XFD080090</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DSGCR_RESERVED_31_28 0x0 - - When RDBI enabled, this bit is used to select RDBI CL calculation, if it is 1b1, calculation will use RDBICL, otherwise use d - fault calculation. - PSU_DDR_PHY_DSGCR_RDBICLSEL 0x0 - - When RDBI enabled, if RDBICLSEL is asserted, RDBI CL adjust using this value. - PSU_DDR_PHY_DSGCR_RDBICL 0x2 - - PHY Impedance Update Enable - PSU_DDR_PHY_DSGCR_PHYZUEN 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DSGCR_RESERVED_22 0x0 - - SDRAM Reset Output Enable - PSU_DDR_PHY_DSGCR_RSTOE 0x1 - - Single Data Rate Mode - PSU_DDR_PHY_DSGCR_SDRMODE 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DSGCR_RESERVED_18 0x0 - - ATO Analog Test Enable - PSU_DDR_PHY_DSGCR_ATOAE 0x0 - - DTO Output Enable - PSU_DDR_PHY_DSGCR_DTOOE 0x0 - - DTO I/O Mode - PSU_DDR_PHY_DSGCR_DTOIOM 0x0 - - DTO Power Down Receiver - PSU_DDR_PHY_DSGCR_DTOPDR 0x1 - - Reserved. Return zeroes on reads - PSU_DDR_PHY_DSGCR_RESERVED_13 0x0 - - DTO On-Die Termination - PSU_DDR_PHY_DSGCR_DTOODT 0x0 - - PHY Update Acknowledge Delay - PSU_DDR_PHY_DSGCR_PUAD 0x4 - - Controller Update Acknowledge Enable - PSU_DDR_PHY_DSGCR_CUAEN 0x1 - - Reserved. Return zeroes on reads - PSU_DDR_PHY_DSGCR_RESERVED_4_3 0x0 - - Controller Impedance Update Enable - PSU_DDR_PHY_DSGCR_CTLZUEN 0x0 - - Reserved. Return zeroes on reads - PSU_DDR_PHY_DSGCR_RESERVED_1 0x0 - - PHY Update Request Enable - PSU_DDR_PHY_DSGCR_PUREN 0x1 - - DDR System General Configuration Register - (OFFSET, MASK, VALUE) (0XFD080090, 0xFFFFFFFFU ,0x02A04121U) - RegMask = (DDR_PHY_DSGCR_RESERVED_31_28_MASK | DDR_PHY_DSGCR_RDBICLSEL_MASK | DDR_PHY_DSGCR_RDBICL_MASK | DDR_PHY_DSGCR_PHYZUEN_MASK | DDR_PHY_DSGCR_RESERVED_22_MASK | DDR_PHY_DSGCR_RSTOE_MASK | DDR_PHY_DSGCR_SDRMODE_MASK | DDR_PHY_DSGCR_RESERVED_18_MASK | DDR_PHY_DSGCR_ATOAE_MASK | DDR_PHY_DSGCR_DTOOE_MASK | DDR_PHY_DSGCR_DTOIOM_MASK | DDR_PHY_DSGCR_DTOPDR_MASK | DDR_PHY_DSGCR_RESERVED_13_MASK | DDR_PHY_DSGCR_DTOODT_MASK | DDR_PHY_DSGCR_PUAD_MASK | DDR_PHY_DSGCR_CUAEN_MASK | DDR_PHY_DSGCR_RESERVED_4_3_MASK | DDR_PHY_DSGCR_CTLZUEN_MASK | DDR_PHY_DSGCR_RESERVED_1_MASK | DDR_PHY_DSGCR_PUREN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DSGCR_RESERVED_31_28_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_RDBICLSEL_SHIFT - | 0x00000002U << DDR_PHY_DSGCR_RDBICL_SHIFT - | 0x00000001U << DDR_PHY_DSGCR_PHYZUEN_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_RESERVED_22_SHIFT - | 0x00000001U << DDR_PHY_DSGCR_RSTOE_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_SDRMODE_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_RESERVED_18_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_ATOAE_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_DTOOE_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_DTOIOM_SHIFT - | 0x00000001U << DDR_PHY_DSGCR_DTOPDR_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_RESERVED_13_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_DTOODT_SHIFT - | 0x00000004U << DDR_PHY_DSGCR_PUAD_SHIFT - | 0x00000001U << DDR_PHY_DSGCR_CUAEN_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_RESERVED_4_3_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_CTLZUEN_SHIFT - | 0x00000000U << DDR_PHY_DSGCR_RESERVED_1_SHIFT - | 0x00000001U << DDR_PHY_DSGCR_PUREN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DSGCR_OFFSET ,0xFFFFFFFFU ,0x02A04121U); - /*############################################################################################################################ */ - - /*Register : DCR @ 0XFD080100</p> - - DDR4 Gear Down Timing. - PSU_DDR_PHY_DCR_GEARDN 0x0 - - Un-used Bank Group - PSU_DDR_PHY_DCR_UBG 0x0 - - Un-buffered DIMM Address Mirroring - PSU_DDR_PHY_DCR_UDIMM 0x0 - - DDR 2T Timing - PSU_DDR_PHY_DCR_DDR2T 0x0 - - No Simultaneous Rank Access - PSU_DDR_PHY_DCR_NOSRA 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DCR_RESERVED_26_18 0x0 - - Byte Mask - PSU_DDR_PHY_DCR_BYTEMASK 0x1 - - DDR Type - PSU_DDR_PHY_DCR_DDRTYPE 0x0 - - Multi-Purpose Register (MPR) DQ (DDR3 Only) - PSU_DDR_PHY_DCR_MPRDQ 0x0 - - Primary DQ (DDR3 Only) - PSU_DDR_PHY_DCR_PDQ 0x0 - - DDR 8-Bank - PSU_DDR_PHY_DCR_DDR8BNK 0x1 - - DDR Mode - PSU_DDR_PHY_DCR_DDRMD 0x4 - - DRAM Configuration Register - (OFFSET, MASK, VALUE) (0XFD080100, 0xFFFFFFFFU ,0x0800040CU) - RegMask = (DDR_PHY_DCR_GEARDN_MASK | DDR_PHY_DCR_UBG_MASK | DDR_PHY_DCR_UDIMM_MASK | DDR_PHY_DCR_DDR2T_MASK | DDR_PHY_DCR_NOSRA_MASK | DDR_PHY_DCR_RESERVED_26_18_MASK | DDR_PHY_DCR_BYTEMASK_MASK | DDR_PHY_DCR_DDRTYPE_MASK | DDR_PHY_DCR_MPRDQ_MASK | DDR_PHY_DCR_PDQ_MASK | DDR_PHY_DCR_DDR8BNK_MASK | DDR_PHY_DCR_DDRMD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DCR_GEARDN_SHIFT - | 0x00000000U << DDR_PHY_DCR_UBG_SHIFT - | 0x00000000U << DDR_PHY_DCR_UDIMM_SHIFT - | 0x00000000U << DDR_PHY_DCR_DDR2T_SHIFT - | 0x00000001U << DDR_PHY_DCR_NOSRA_SHIFT - | 0x00000000U << DDR_PHY_DCR_RESERVED_26_18_SHIFT - | 0x00000001U << DDR_PHY_DCR_BYTEMASK_SHIFT - | 0x00000000U << DDR_PHY_DCR_DDRTYPE_SHIFT - | 0x00000000U << DDR_PHY_DCR_MPRDQ_SHIFT - | 0x00000000U << DDR_PHY_DCR_PDQ_SHIFT - | 0x00000001U << DDR_PHY_DCR_DDR8BNK_SHIFT - | 0x00000004U << DDR_PHY_DCR_DDRMD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DCR_OFFSET ,0xFFFFFFFFU ,0x0800040CU); - /*############################################################################################################################ */ - - /*Register : DTPR0 @ 0XFD080110</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR0_RESERVED_31_29 0x0 - - Activate to activate command delay (different banks) - PSU_DDR_PHY_DTPR0_TRRD 0x6 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR0_RESERVED_23 0x0 - - Activate to precharge command delay - PSU_DDR_PHY_DTPR0_TRAS 0x24 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR0_RESERVED_15 0x0 - - Precharge command period - PSU_DDR_PHY_DTPR0_TRP 0xf - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR0_RESERVED_7_5 0x0 - - Internal read to precharge command delay - PSU_DDR_PHY_DTPR0_TRTP 0x9 - - DRAM Timing Parameters Register 0 - (OFFSET, MASK, VALUE) (0XFD080110, 0xFFFFFFFFU ,0x06240F09U) - RegMask = (DDR_PHY_DTPR0_RESERVED_31_29_MASK | DDR_PHY_DTPR0_TRRD_MASK | DDR_PHY_DTPR0_RESERVED_23_MASK | DDR_PHY_DTPR0_TRAS_MASK | DDR_PHY_DTPR0_RESERVED_15_MASK | DDR_PHY_DTPR0_TRP_MASK | DDR_PHY_DTPR0_RESERVED_7_5_MASK | DDR_PHY_DTPR0_TRTP_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DTPR0_RESERVED_31_29_SHIFT - | 0x00000006U << DDR_PHY_DTPR0_TRRD_SHIFT - | 0x00000000U << DDR_PHY_DTPR0_RESERVED_23_SHIFT - | 0x00000024U << DDR_PHY_DTPR0_TRAS_SHIFT - | 0x00000000U << DDR_PHY_DTPR0_RESERVED_15_SHIFT - | 0x0000000FU << DDR_PHY_DTPR0_TRP_SHIFT - | 0x00000000U << DDR_PHY_DTPR0_RESERVED_7_5_SHIFT - | 0x00000009U << DDR_PHY_DTPR0_TRTP_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DTPR0_OFFSET ,0xFFFFFFFFU ,0x06240F09U); - /*############################################################################################################################ */ - - /*Register : DTPR1 @ 0XFD080114</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR1_RESERVED_31 0x0 - - Minimum delay from when write leveling mode is programmed to the first DQS/DQS# rising edge. - PSU_DDR_PHY_DTPR1_TWLMRD 0x28 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR1_RESERVED_23 0x0 - - 4-bank activate period - PSU_DDR_PHY_DTPR1_TFAW 0x22 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR1_RESERVED_15_11 0x0 - - Load mode update delay (DDR4 and DDR3 only) - PSU_DDR_PHY_DTPR1_TMOD 0x7 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR1_RESERVED_7_5 0x0 - - Load mode cycle time - PSU_DDR_PHY_DTPR1_TMRD 0x8 - - DRAM Timing Parameters Register 1 - (OFFSET, MASK, VALUE) (0XFD080114, 0xFFFFFFFFU ,0x28220708U) - RegMask = (DDR_PHY_DTPR1_RESERVED_31_MASK | DDR_PHY_DTPR1_TWLMRD_MASK | DDR_PHY_DTPR1_RESERVED_23_MASK | DDR_PHY_DTPR1_TFAW_MASK | DDR_PHY_DTPR1_RESERVED_15_11_MASK | DDR_PHY_DTPR1_TMOD_MASK | DDR_PHY_DTPR1_RESERVED_7_5_MASK | DDR_PHY_DTPR1_TMRD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DTPR1_RESERVED_31_SHIFT - | 0x00000028U << DDR_PHY_DTPR1_TWLMRD_SHIFT - | 0x00000000U << DDR_PHY_DTPR1_RESERVED_23_SHIFT - | 0x00000022U << DDR_PHY_DTPR1_TFAW_SHIFT - | 0x00000000U << DDR_PHY_DTPR1_RESERVED_15_11_SHIFT - | 0x00000007U << DDR_PHY_DTPR1_TMOD_SHIFT - | 0x00000000U << DDR_PHY_DTPR1_RESERVED_7_5_SHIFT - | 0x00000008U << DDR_PHY_DTPR1_TMRD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DTPR1_OFFSET ,0xFFFFFFFFU ,0x28220708U); - /*############################################################################################################################ */ - - /*Register : DTPR2 @ 0XFD080118</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR2_RESERVED_31_29 0x0 - - Read to Write command delay. Valid values are - PSU_DDR_PHY_DTPR2_TRTW 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR2_RESERVED_27_25 0x0 - - Read to ODT delay (DDR3 only) - PSU_DDR_PHY_DTPR2_TRTODT 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR2_RESERVED_23_20 0x0 - - CKE minimum pulse width - PSU_DDR_PHY_DTPR2_TCKE 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR2_RESERVED_15_10 0x0 - - Self refresh exit delay - PSU_DDR_PHY_DTPR2_TXS 0x200 - - DRAM Timing Parameters Register 2 - (OFFSET, MASK, VALUE) (0XFD080118, 0xFFFFFFFFU ,0x00080200U) - RegMask = (DDR_PHY_DTPR2_RESERVED_31_29_MASK | DDR_PHY_DTPR2_TRTW_MASK | DDR_PHY_DTPR2_RESERVED_27_25_MASK | DDR_PHY_DTPR2_TRTODT_MASK | DDR_PHY_DTPR2_RESERVED_23_20_MASK | DDR_PHY_DTPR2_TCKE_MASK | DDR_PHY_DTPR2_RESERVED_15_10_MASK | DDR_PHY_DTPR2_TXS_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DTPR2_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_DTPR2_TRTW_SHIFT - | 0x00000000U << DDR_PHY_DTPR2_RESERVED_27_25_SHIFT - | 0x00000000U << DDR_PHY_DTPR2_TRTODT_SHIFT - | 0x00000000U << DDR_PHY_DTPR2_RESERVED_23_20_SHIFT - | 0x00000008U << DDR_PHY_DTPR2_TCKE_SHIFT - | 0x00000000U << DDR_PHY_DTPR2_RESERVED_15_10_SHIFT - | 0x00000200U << DDR_PHY_DTPR2_TXS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DTPR2_OFFSET ,0xFFFFFFFFU ,0x00080200U); - /*############################################################################################################################ */ - - /*Register : DTPR3 @ 0XFD08011C</p> - - ODT turn-off delay extension - PSU_DDR_PHY_DTPR3_TOFDX 0x4 - - Read to read and write to write command delay - PSU_DDR_PHY_DTPR3_TCCD 0x0 - - DLL locking time - PSU_DDR_PHY_DTPR3_TDLLK 0x300 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR3_RESERVED_15_12 0x0 - - Maximum DQS output access time from CK/CK# (LPDDR2/3 only) - PSU_DDR_PHY_DTPR3_TDQSCKMAX 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR3_RESERVED_7_3 0x0 - - DQS output access time from CK/CK# (LPDDR2/3 only) - PSU_DDR_PHY_DTPR3_TDQSCK 0x0 - - DRAM Timing Parameters Register 3 - (OFFSET, MASK, VALUE) (0XFD08011C, 0xFFFFFFFFU ,0x83000800U) - RegMask = (DDR_PHY_DTPR3_TOFDX_MASK | DDR_PHY_DTPR3_TCCD_MASK | DDR_PHY_DTPR3_TDLLK_MASK | DDR_PHY_DTPR3_RESERVED_15_12_MASK | DDR_PHY_DTPR3_TDQSCKMAX_MASK | DDR_PHY_DTPR3_RESERVED_7_3_MASK | DDR_PHY_DTPR3_TDQSCK_MASK | 0 ); - - RegVal = ((0x00000004U << DDR_PHY_DTPR3_TOFDX_SHIFT - | 0x00000000U << DDR_PHY_DTPR3_TCCD_SHIFT - | 0x00000300U << DDR_PHY_DTPR3_TDLLK_SHIFT - | 0x00000000U << DDR_PHY_DTPR3_RESERVED_15_12_SHIFT - | 0x00000008U << DDR_PHY_DTPR3_TDQSCKMAX_SHIFT - | 0x00000000U << DDR_PHY_DTPR3_RESERVED_7_3_SHIFT - | 0x00000000U << DDR_PHY_DTPR3_TDQSCK_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DTPR3_OFFSET ,0xFFFFFFFFU ,0x83000800U); - /*############################################################################################################################ */ - - /*Register : DTPR4 @ 0XFD080120</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR4_RESERVED_31_30 0x0 - - ODT turn-on/turn-off delays (DDR2 only) - PSU_DDR_PHY_DTPR4_TAOND_TAOFD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR4_RESERVED_27_26 0x0 - - Refresh-to-Refresh - PSU_DDR_PHY_DTPR4_TRFC 0x116 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR4_RESERVED_15_14 0x0 - - Write leveling output delay - PSU_DDR_PHY_DTPR4_TWLO 0x2b - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR4_RESERVED_7_5 0x0 - - Power down exit delay - PSU_DDR_PHY_DTPR4_TXP 0x8 - - DRAM Timing Parameters Register 4 - (OFFSET, MASK, VALUE) (0XFD080120, 0xFFFFFFFFU ,0x01162B08U) - RegMask = (DDR_PHY_DTPR4_RESERVED_31_30_MASK | DDR_PHY_DTPR4_TAOND_TAOFD_MASK | DDR_PHY_DTPR4_RESERVED_27_26_MASK | DDR_PHY_DTPR4_TRFC_MASK | DDR_PHY_DTPR4_RESERVED_15_14_MASK | DDR_PHY_DTPR4_TWLO_MASK | DDR_PHY_DTPR4_RESERVED_7_5_MASK | DDR_PHY_DTPR4_TXP_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DTPR4_RESERVED_31_30_SHIFT - | 0x00000000U << DDR_PHY_DTPR4_TAOND_TAOFD_SHIFT - | 0x00000000U << DDR_PHY_DTPR4_RESERVED_27_26_SHIFT - | 0x00000116U << DDR_PHY_DTPR4_TRFC_SHIFT - | 0x00000000U << DDR_PHY_DTPR4_RESERVED_15_14_SHIFT - | 0x0000002BU << DDR_PHY_DTPR4_TWLO_SHIFT - | 0x00000000U << DDR_PHY_DTPR4_RESERVED_7_5_SHIFT - | 0x00000008U << DDR_PHY_DTPR4_TXP_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DTPR4_OFFSET ,0xFFFFFFFFU ,0x01162B08U); - /*############################################################################################################################ */ - - /*Register : DTPR5 @ 0XFD080124</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR5_RESERVED_31_24 0x0 - - Activate to activate command delay (same bank) - PSU_DDR_PHY_DTPR5_TRC 0x34 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR5_RESERVED_15 0x0 - - Activate to read or write delay - PSU_DDR_PHY_DTPR5_TRCD 0xf - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR5_RESERVED_7_5 0x0 - - Internal write to read command delay - PSU_DDR_PHY_DTPR5_TWTR 0x9 - - DRAM Timing Parameters Register 5 - (OFFSET, MASK, VALUE) (0XFD080124, 0xFFFFFFFFU ,0x00340F09U) - RegMask = (DDR_PHY_DTPR5_RESERVED_31_24_MASK | DDR_PHY_DTPR5_TRC_MASK | DDR_PHY_DTPR5_RESERVED_15_MASK | DDR_PHY_DTPR5_TRCD_MASK | DDR_PHY_DTPR5_RESERVED_7_5_MASK | DDR_PHY_DTPR5_TWTR_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DTPR5_RESERVED_31_24_SHIFT - | 0x00000034U << DDR_PHY_DTPR5_TRC_SHIFT - | 0x00000000U << DDR_PHY_DTPR5_RESERVED_15_SHIFT - | 0x0000000FU << DDR_PHY_DTPR5_TRCD_SHIFT - | 0x00000000U << DDR_PHY_DTPR5_RESERVED_7_5_SHIFT - | 0x00000009U << DDR_PHY_DTPR5_TWTR_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DTPR5_OFFSET ,0xFFFFFFFFU ,0x00340F09U); - /*############################################################################################################################ */ - - /*Register : DTPR6 @ 0XFD080128</p> - - PUB Write Latency Enable - PSU_DDR_PHY_DTPR6_PUBWLEN 0x0 - - PUB Read Latency Enable - PSU_DDR_PHY_DTPR6_PUBRLEN 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR6_RESERVED_29_14 0x0 - - Write Latency - PSU_DDR_PHY_DTPR6_PUBWL 0xe - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTPR6_RESERVED_7_6 0x0 - - Read Latency - PSU_DDR_PHY_DTPR6_PUBRL 0xf - - DRAM Timing Parameters Register 6 - (OFFSET, MASK, VALUE) (0XFD080128, 0xFFFFFFFFU ,0x00000E0FU) - RegMask = (DDR_PHY_DTPR6_PUBWLEN_MASK | DDR_PHY_DTPR6_PUBRLEN_MASK | DDR_PHY_DTPR6_RESERVED_29_14_MASK | DDR_PHY_DTPR6_PUBWL_MASK | DDR_PHY_DTPR6_RESERVED_7_6_MASK | DDR_PHY_DTPR6_PUBRL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DTPR6_PUBWLEN_SHIFT - | 0x00000000U << DDR_PHY_DTPR6_PUBRLEN_SHIFT - | 0x00000000U << DDR_PHY_DTPR6_RESERVED_29_14_SHIFT - | 0x0000000EU << DDR_PHY_DTPR6_PUBWL_SHIFT - | 0x00000000U << DDR_PHY_DTPR6_RESERVED_7_6_SHIFT - | 0x0000000FU << DDR_PHY_DTPR6_PUBRL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DTPR6_OFFSET ,0xFFFFFFFFU ,0x00000E0FU); - /*############################################################################################################################ */ - - /*Register : RDIMMGCR0 @ 0XFD080140</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR0_RESERVED_31 0x0 - - RDMIMM Quad CS Enable - PSU_DDR_PHY_RDIMMGCR0_QCSEN 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR0_RESERVED_29_28 0x0 - - RDIMM Outputs I/O Mode - PSU_DDR_PHY_RDIMMGCR0_RDIMMIOM 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR0_RESERVED_26_24 0x0 - - ERROUT# Output Enable - PSU_DDR_PHY_RDIMMGCR0_ERROUTOE 0x0 - - ERROUT# I/O Mode - PSU_DDR_PHY_RDIMMGCR0_ERROUTIOM 0x1 - - ERROUT# Power Down Receiver - PSU_DDR_PHY_RDIMMGCR0_ERROUTPDR 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR0_RESERVED_20 0x0 - - ERROUT# On-Die Termination - PSU_DDR_PHY_RDIMMGCR0_ERROUTODT 0x0 - - Load Reduced DIMM - PSU_DDR_PHY_RDIMMGCR0_LRDIMM 0x0 - - PAR_IN I/O Mode - PSU_DDR_PHY_RDIMMGCR0_PARINIOM 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR0_RESERVED_16_8 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD 0x0 - - Rank Mirror Enable. - PSU_DDR_PHY_RDIMMGCR0_RNKMRREN 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR0_RESERVED_3 0x0 - - Stop on Parity Error - PSU_DDR_PHY_RDIMMGCR0_SOPERR 0x0 - - Parity Error No Registering - PSU_DDR_PHY_RDIMMGCR0_ERRNOREG 0x0 - - Registered DIMM - PSU_DDR_PHY_RDIMMGCR0_RDIMM 0x0 - - RDIMM General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080140, 0xFFFFFFFFU ,0x08400020U) - RegMask = (DDR_PHY_RDIMMGCR0_RESERVED_31_MASK | DDR_PHY_RDIMMGCR0_QCSEN_MASK | DDR_PHY_RDIMMGCR0_RESERVED_29_28_MASK | DDR_PHY_RDIMMGCR0_RDIMMIOM_MASK | DDR_PHY_RDIMMGCR0_RESERVED_26_24_MASK | DDR_PHY_RDIMMGCR0_ERROUTOE_MASK | DDR_PHY_RDIMMGCR0_ERROUTIOM_MASK | DDR_PHY_RDIMMGCR0_ERROUTPDR_MASK | DDR_PHY_RDIMMGCR0_RESERVED_20_MASK | DDR_PHY_RDIMMGCR0_ERROUTODT_MASK | DDR_PHY_RDIMMGCR0_LRDIMM_MASK | DDR_PHY_RDIMMGCR0_PARINIOM_MASK | DDR_PHY_RDIMMGCR0_RESERVED_16_8_MASK | DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD_MASK | DDR_PHY_RDIMMGCR0_RNKMRREN_MASK | DDR_PHY_RDIMMGCR0_RESERVED_3_MASK | DDR_PHY_RDIMMGCR0_SOPERR_MASK | DDR_PHY_RDIMMGCR0_ERRNOREG_MASK | DDR_PHY_RDIMMGCR0_RDIMM_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_RDIMMGCR0_RESERVED_31_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_QCSEN_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_RESERVED_29_28_SHIFT - | 0x00000001U << DDR_PHY_RDIMMGCR0_RDIMMIOM_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_RESERVED_26_24_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_ERROUTOE_SHIFT - | 0x00000001U << DDR_PHY_RDIMMGCR0_ERROUTIOM_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_ERROUTPDR_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_RESERVED_20_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_ERROUTODT_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_LRDIMM_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_PARINIOM_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_RESERVED_16_8_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD_SHIFT - | 0x00000002U << DDR_PHY_RDIMMGCR0_RNKMRREN_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_RESERVED_3_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_SOPERR_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_ERRNOREG_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR0_RDIMM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_RDIMMGCR0_OFFSET ,0xFFFFFFFFU ,0x08400020U); - /*############################################################################################################################ */ - - /*Register : RDIMMGCR1 @ 0XFD080144</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR1_RESERVED_31_29 0x0 - - Address [17] B-side Inversion Disable - PSU_DDR_PHY_RDIMMGCR1_A17BID 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR1_RESERVED_27 0x0 - - Command word to command word programming delay - PSU_DDR_PHY_RDIMMGCR1_TBCMRD_L2 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR1_RESERVED_23 0x0 - - Command word to command word programming delay - PSU_DDR_PHY_RDIMMGCR1_TBCMRD_L 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR1_RESERVED_19 0x0 - - Command word to command word programming delay - PSU_DDR_PHY_RDIMMGCR1_TBCMRD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RDIMMGCR1_RESERVED_15_14 0x0 - - Stabilization time - PSU_DDR_PHY_RDIMMGCR1_TBCSTAB 0xc80 - - RDIMM General Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD080144, 0xFFFFFFFFU ,0x00000C80U) - RegMask = (DDR_PHY_RDIMMGCR1_RESERVED_31_29_MASK | DDR_PHY_RDIMMGCR1_A17BID_MASK | DDR_PHY_RDIMMGCR1_RESERVED_27_MASK | DDR_PHY_RDIMMGCR1_TBCMRD_L2_MASK | DDR_PHY_RDIMMGCR1_RESERVED_23_MASK | DDR_PHY_RDIMMGCR1_TBCMRD_L_MASK | DDR_PHY_RDIMMGCR1_RESERVED_19_MASK | DDR_PHY_RDIMMGCR1_TBCMRD_MASK | DDR_PHY_RDIMMGCR1_RESERVED_15_14_MASK | DDR_PHY_RDIMMGCR1_TBCSTAB_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_RDIMMGCR1_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR1_A17BID_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR1_RESERVED_27_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR1_TBCMRD_L2_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR1_RESERVED_23_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR1_TBCMRD_L_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR1_RESERVED_19_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR1_TBCMRD_SHIFT - | 0x00000000U << DDR_PHY_RDIMMGCR1_RESERVED_15_14_SHIFT - | 0x00000C80U << DDR_PHY_RDIMMGCR1_TBCSTAB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_RDIMMGCR1_OFFSET ,0xFFFFFFFFU ,0x00000C80U); - /*############################################################################################################################ */ - - /*Register : RDIMMCR0 @ 0XFD080150</p> - - DDR4/DDR3 Control Word 7 - PSU_DDR_PHY_RDIMMCR0_RC7 0x0 - - DDR4 Control Word 6 (Comman space Control Word) / DDR3 Reserved - PSU_DDR_PHY_RDIMMCR0_RC6 0x0 - - DDR4/DDR3 Control Word 5 (CK Driver Characteristics Control Word) - PSU_DDR_PHY_RDIMMCR0_RC5 0x0 - - DDR4 Control Word 4 (ODT and CKE Signals Driver Characteristics Control Word) / DDR3 Control Word 4 (Control Signals Driver C - aracteristics Control Word) - PSU_DDR_PHY_RDIMMCR0_RC4 0x0 - - DDR4 Control Word 3 (CA and CS Signals Driver Characteristics Control Word) / DDR3 Control Word 3 (Command/Address Signals Dr - ver Characteristrics Control Word) - PSU_DDR_PHY_RDIMMCR0_RC3 0x0 - - DDR4 Control Word 2 (Timing and IBT Control Word) / DDR3 Control Word 2 (Timing Control Word) - PSU_DDR_PHY_RDIMMCR0_RC2 0x0 - - DDR4/DDR3 Control Word 1 (Clock Driver Enable Control Word) - PSU_DDR_PHY_RDIMMCR0_RC1 0x0 - - DDR4/DDR3 Control Word 0 (Global Features Control Word) - PSU_DDR_PHY_RDIMMCR0_RC0 0x0 - - RDIMM Control Register 0 - (OFFSET, MASK, VALUE) (0XFD080150, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_RDIMMCR0_RC7_MASK | DDR_PHY_RDIMMCR0_RC6_MASK | DDR_PHY_RDIMMCR0_RC5_MASK | DDR_PHY_RDIMMCR0_RC4_MASK | DDR_PHY_RDIMMCR0_RC3_MASK | DDR_PHY_RDIMMCR0_RC2_MASK | DDR_PHY_RDIMMCR0_RC1_MASK | DDR_PHY_RDIMMCR0_RC0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_RDIMMCR0_RC7_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR0_RC6_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR0_RC5_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR0_RC4_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR0_RC3_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR0_RC2_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR0_RC1_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR0_RC0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_RDIMMCR0_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : RDIMMCR1 @ 0XFD080154</p> - - Control Word 15 - PSU_DDR_PHY_RDIMMCR1_RC15 0x0 - - DDR4 Control Word 14 (Parity Control Word) / DDR3 Reserved - PSU_DDR_PHY_RDIMMCR1_RC14 0x0 - - DDR4 Control Word 13 (DIMM Configuration Control Word) / DDR3 Reserved - PSU_DDR_PHY_RDIMMCR1_RC13 0x0 - - DDR4 Control Word 12 (Training Control Word) / DDR3 Reserved - PSU_DDR_PHY_RDIMMCR1_RC12 0x0 - - DDR4 Control Word 11 (Operating Voltage VDD and VREFCA Source Control Word) / DDR3 Control Word 11 (Operation Voltage VDD Con - rol Word) - PSU_DDR_PHY_RDIMMCR1_RC11 0x0 - - DDR4/DDR3 Control Word 10 (RDIMM Operating Speed Control Word) - PSU_DDR_PHY_RDIMMCR1_RC10 0x2 - - DDR4/DDR3 Control Word 9 (Power Saving Settings Control Word) - PSU_DDR_PHY_RDIMMCR1_RC9 0x0 - - DDR4 Control Word 8 (Input/Output Configuration Control Word) / DDR3 Control Word 8 (Additional Input Bus Termination Setting - Control Word) - PSU_DDR_PHY_RDIMMCR1_RC8 0x0 - - RDIMM Control Register 1 - (OFFSET, MASK, VALUE) (0XFD080154, 0xFFFFFFFFU ,0x00000200U) - RegMask = (DDR_PHY_RDIMMCR1_RC15_MASK | DDR_PHY_RDIMMCR1_RC14_MASK | DDR_PHY_RDIMMCR1_RC13_MASK | DDR_PHY_RDIMMCR1_RC12_MASK | DDR_PHY_RDIMMCR1_RC11_MASK | DDR_PHY_RDIMMCR1_RC10_MASK | DDR_PHY_RDIMMCR1_RC9_MASK | DDR_PHY_RDIMMCR1_RC8_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_RDIMMCR1_RC15_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR1_RC14_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR1_RC13_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR1_RC12_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR1_RC11_SHIFT - | 0x00000002U << DDR_PHY_RDIMMCR1_RC10_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR1_RC9_SHIFT - | 0x00000000U << DDR_PHY_RDIMMCR1_RC8_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_RDIMMCR1_OFFSET ,0xFFFFFFFFU ,0x00000200U); - /*############################################################################################################################ */ - - /*Register : MR0 @ 0XFD080180</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR0_RESERVED_31_8 0x8 - - CA Terminating Rank - PSU_DDR_PHY_MR0_CATR 0x0 - - Reserved. These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR0_RSVD_6_5 0x1 - - Built-in Self-Test for RZQ - PSU_DDR_PHY_MR0_RZQI 0x2 - - Reserved. These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR0_RSVD_2_0 0x0 - - LPDDR4 Mode Register 0 - (OFFSET, MASK, VALUE) (0XFD080180, 0xFFFFFFFFU ,0x00000830U) - RegMask = (DDR_PHY_MR0_RESERVED_31_8_MASK | DDR_PHY_MR0_CATR_MASK | DDR_PHY_MR0_RSVD_6_5_MASK | DDR_PHY_MR0_RZQI_MASK | DDR_PHY_MR0_RSVD_2_0_MASK | 0 ); - - RegVal = ((0x00000008U << DDR_PHY_MR0_RESERVED_31_8_SHIFT - | 0x00000000U << DDR_PHY_MR0_CATR_SHIFT - | 0x00000001U << DDR_PHY_MR0_RSVD_6_5_SHIFT - | 0x00000002U << DDR_PHY_MR0_RZQI_SHIFT - | 0x00000000U << DDR_PHY_MR0_RSVD_2_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR0_OFFSET ,0xFFFFFFFFU ,0x00000830U); - /*############################################################################################################################ */ - - /*Register : MR1 @ 0XFD080184</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR1_RESERVED_31_8 0x3 - - Read Postamble Length - PSU_DDR_PHY_MR1_RDPST 0x0 - - Write-recovery for auto-precharge command - PSU_DDR_PHY_MR1_NWR 0x0 - - Read Preamble Length - PSU_DDR_PHY_MR1_RDPRE 0x0 - - Write Preamble Length - PSU_DDR_PHY_MR1_WRPRE 0x0 - - Burst Length - PSU_DDR_PHY_MR1_BL 0x1 - - LPDDR4 Mode Register 1 - (OFFSET, MASK, VALUE) (0XFD080184, 0xFFFFFFFFU ,0x00000301U) - RegMask = (DDR_PHY_MR1_RESERVED_31_8_MASK | DDR_PHY_MR1_RDPST_MASK | DDR_PHY_MR1_NWR_MASK | DDR_PHY_MR1_RDPRE_MASK | DDR_PHY_MR1_WRPRE_MASK | DDR_PHY_MR1_BL_MASK | 0 ); - - RegVal = ((0x00000003U << DDR_PHY_MR1_RESERVED_31_8_SHIFT - | 0x00000000U << DDR_PHY_MR1_RDPST_SHIFT - | 0x00000000U << DDR_PHY_MR1_NWR_SHIFT - | 0x00000000U << DDR_PHY_MR1_RDPRE_SHIFT - | 0x00000000U << DDR_PHY_MR1_WRPRE_SHIFT - | 0x00000001U << DDR_PHY_MR1_BL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR1_OFFSET ,0xFFFFFFFFU ,0x00000301U); - /*############################################################################################################################ */ - - /*Register : MR2 @ 0XFD080188</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR2_RESERVED_31_8 0x0 - - Write Leveling - PSU_DDR_PHY_MR2_WRL 0x0 - - Write Latency Set - PSU_DDR_PHY_MR2_WLS 0x0 - - Write Latency - PSU_DDR_PHY_MR2_WL 0x4 - - Read Latency - PSU_DDR_PHY_MR2_RL 0x0 - - LPDDR4 Mode Register 2 - (OFFSET, MASK, VALUE) (0XFD080188, 0xFFFFFFFFU ,0x00000020U) - RegMask = (DDR_PHY_MR2_RESERVED_31_8_MASK | DDR_PHY_MR2_WRL_MASK | DDR_PHY_MR2_WLS_MASK | DDR_PHY_MR2_WL_MASK | DDR_PHY_MR2_RL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_MR2_RESERVED_31_8_SHIFT - | 0x00000000U << DDR_PHY_MR2_WRL_SHIFT - | 0x00000000U << DDR_PHY_MR2_WLS_SHIFT - | 0x00000004U << DDR_PHY_MR2_WL_SHIFT - | 0x00000000U << DDR_PHY_MR2_RL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR2_OFFSET ,0xFFFFFFFFU ,0x00000020U); - /*############################################################################################################################ */ - - /*Register : MR3 @ 0XFD08018C</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR3_RESERVED_31_8 0x2 - - DBI-Write Enable - PSU_DDR_PHY_MR3_DBIWR 0x0 - - DBI-Read Enable - PSU_DDR_PHY_MR3_DBIRD 0x0 - - Pull-down Drive Strength - PSU_DDR_PHY_MR3_PDDS 0x0 - - These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR3_RSVD 0x0 - - Write Postamble Length - PSU_DDR_PHY_MR3_WRPST 0x0 - - Pull-up Calibration Point - PSU_DDR_PHY_MR3_PUCAL 0x0 - - LPDDR4 Mode Register 3 - (OFFSET, MASK, VALUE) (0XFD08018C, 0xFFFFFFFFU ,0x00000200U) - RegMask = (DDR_PHY_MR3_RESERVED_31_8_MASK | DDR_PHY_MR3_DBIWR_MASK | DDR_PHY_MR3_DBIRD_MASK | DDR_PHY_MR3_PDDS_MASK | DDR_PHY_MR3_RSVD_MASK | DDR_PHY_MR3_WRPST_MASK | DDR_PHY_MR3_PUCAL_MASK | 0 ); - - RegVal = ((0x00000002U << DDR_PHY_MR3_RESERVED_31_8_SHIFT - | 0x00000000U << DDR_PHY_MR3_DBIWR_SHIFT - | 0x00000000U << DDR_PHY_MR3_DBIRD_SHIFT - | 0x00000000U << DDR_PHY_MR3_PDDS_SHIFT - | 0x00000000U << DDR_PHY_MR3_RSVD_SHIFT - | 0x00000000U << DDR_PHY_MR3_WRPST_SHIFT - | 0x00000000U << DDR_PHY_MR3_PUCAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR3_OFFSET ,0xFFFFFFFFU ,0x00000200U); - /*############################################################################################################################ */ - - /*Register : MR4 @ 0XFD080190</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR4_RESERVED_31_16 0x0 - - These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR4_RSVD_15_13 0x0 - - Write Preamble - PSU_DDR_PHY_MR4_WRP 0x0 - - Read Preamble - PSU_DDR_PHY_MR4_RDP 0x0 - - Read Preamble Training Mode - PSU_DDR_PHY_MR4_RPTM 0x0 - - Self Refresh Abort - PSU_DDR_PHY_MR4_SRA 0x0 - - CS to Command Latency Mode - PSU_DDR_PHY_MR4_CS2CMDL 0x0 - - These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR4_RSVD1 0x0 - - Internal VREF Monitor - PSU_DDR_PHY_MR4_IVM 0x0 - - Temperature Controlled Refresh Mode - PSU_DDR_PHY_MR4_TCRM 0x0 - - Temperature Controlled Refresh Range - PSU_DDR_PHY_MR4_TCRR 0x0 - - Maximum Power Down Mode - PSU_DDR_PHY_MR4_MPDM 0x0 - - This is a JEDEC reserved bit and is recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR4_RSVD_0 0x0 - - DDR4 Mode Register 4 - (OFFSET, MASK, VALUE) (0XFD080190, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_MR4_RESERVED_31_16_MASK | DDR_PHY_MR4_RSVD_15_13_MASK | DDR_PHY_MR4_WRP_MASK | DDR_PHY_MR4_RDP_MASK | DDR_PHY_MR4_RPTM_MASK | DDR_PHY_MR4_SRA_MASK | DDR_PHY_MR4_CS2CMDL_MASK | DDR_PHY_MR4_RSVD1_MASK | DDR_PHY_MR4_IVM_MASK | DDR_PHY_MR4_TCRM_MASK | DDR_PHY_MR4_TCRR_MASK | DDR_PHY_MR4_MPDM_MASK | DDR_PHY_MR4_RSVD_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_MR4_RESERVED_31_16_SHIFT - | 0x00000000U << DDR_PHY_MR4_RSVD_15_13_SHIFT - | 0x00000000U << DDR_PHY_MR4_WRP_SHIFT - | 0x00000000U << DDR_PHY_MR4_RDP_SHIFT - | 0x00000000U << DDR_PHY_MR4_RPTM_SHIFT - | 0x00000000U << DDR_PHY_MR4_SRA_SHIFT - | 0x00000000U << DDR_PHY_MR4_CS2CMDL_SHIFT - | 0x00000000U << DDR_PHY_MR4_RSVD1_SHIFT - | 0x00000000U << DDR_PHY_MR4_IVM_SHIFT - | 0x00000000U << DDR_PHY_MR4_TCRM_SHIFT - | 0x00000000U << DDR_PHY_MR4_TCRR_SHIFT - | 0x00000000U << DDR_PHY_MR4_MPDM_SHIFT - | 0x00000000U << DDR_PHY_MR4_RSVD_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR4_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MR5 @ 0XFD080194</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR5_RESERVED_31_16 0x0 - - These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR5_RSVD 0x0 - - Read DBI - PSU_DDR_PHY_MR5_RDBI 0x0 - - Write DBI - PSU_DDR_PHY_MR5_WDBI 0x0 - - Data Mask - PSU_DDR_PHY_MR5_DM 0x1 - - CA Parity Persistent Error - PSU_DDR_PHY_MR5_CAPPE 0x1 - - RTT_PARK - PSU_DDR_PHY_MR5_RTTPARK 0x3 - - ODT Input Buffer during Power Down mode - PSU_DDR_PHY_MR5_ODTIBPD 0x0 - - C/A Parity Error Status - PSU_DDR_PHY_MR5_CAPES 0x0 - - CRC Error Clear - PSU_DDR_PHY_MR5_CRCEC 0x0 - - C/A Parity Latency Mode - PSU_DDR_PHY_MR5_CAPM 0x0 - - DDR4 Mode Register 5 - (OFFSET, MASK, VALUE) (0XFD080194, 0xFFFFFFFFU ,0x000006C0U) - RegMask = (DDR_PHY_MR5_RESERVED_31_16_MASK | DDR_PHY_MR5_RSVD_MASK | DDR_PHY_MR5_RDBI_MASK | DDR_PHY_MR5_WDBI_MASK | DDR_PHY_MR5_DM_MASK | DDR_PHY_MR5_CAPPE_MASK | DDR_PHY_MR5_RTTPARK_MASK | DDR_PHY_MR5_ODTIBPD_MASK | DDR_PHY_MR5_CAPES_MASK | DDR_PHY_MR5_CRCEC_MASK | DDR_PHY_MR5_CAPM_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_MR5_RESERVED_31_16_SHIFT - | 0x00000000U << DDR_PHY_MR5_RSVD_SHIFT - | 0x00000000U << DDR_PHY_MR5_RDBI_SHIFT - | 0x00000000U << DDR_PHY_MR5_WDBI_SHIFT - | 0x00000001U << DDR_PHY_MR5_DM_SHIFT - | 0x00000001U << DDR_PHY_MR5_CAPPE_SHIFT - | 0x00000003U << DDR_PHY_MR5_RTTPARK_SHIFT - | 0x00000000U << DDR_PHY_MR5_ODTIBPD_SHIFT - | 0x00000000U << DDR_PHY_MR5_CAPES_SHIFT - | 0x00000000U << DDR_PHY_MR5_CRCEC_SHIFT - | 0x00000000U << DDR_PHY_MR5_CAPM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR5_OFFSET ,0xFFFFFFFFU ,0x000006C0U); - /*############################################################################################################################ */ - - /*Register : MR6 @ 0XFD080198</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR6_RESERVED_31_16 0x0 - - These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR6_RSVD_15_13 0x0 - - CAS_n to CAS_n command delay for same bank group (tCCD_L) - PSU_DDR_PHY_MR6_TCCDL 0x2 - - These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR6_RSVD_9_8 0x0 - - VrefDQ Training Enable - PSU_DDR_PHY_MR6_VDDQTEN 0x0 - - VrefDQ Training Range - PSU_DDR_PHY_MR6_VDQTRG 0x0 - - VrefDQ Training Values - PSU_DDR_PHY_MR6_VDQTVAL 0x19 - - DDR4 Mode Register 6 - (OFFSET, MASK, VALUE) (0XFD080198, 0xFFFFFFFFU ,0x00000819U) - RegMask = (DDR_PHY_MR6_RESERVED_31_16_MASK | DDR_PHY_MR6_RSVD_15_13_MASK | DDR_PHY_MR6_TCCDL_MASK | DDR_PHY_MR6_RSVD_9_8_MASK | DDR_PHY_MR6_VDDQTEN_MASK | DDR_PHY_MR6_VDQTRG_MASK | DDR_PHY_MR6_VDQTVAL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_MR6_RESERVED_31_16_SHIFT - | 0x00000000U << DDR_PHY_MR6_RSVD_15_13_SHIFT - | 0x00000002U << DDR_PHY_MR6_TCCDL_SHIFT - | 0x00000000U << DDR_PHY_MR6_RSVD_9_8_SHIFT - | 0x00000000U << DDR_PHY_MR6_VDDQTEN_SHIFT - | 0x00000000U << DDR_PHY_MR6_VDQTRG_SHIFT - | 0x00000019U << DDR_PHY_MR6_VDQTVAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR6_OFFSET ,0xFFFFFFFFU ,0x00000819U); - /*############################################################################################################################ */ - - /*Register : MR11 @ 0XFD0801AC</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR11_RESERVED_31_8 0x0 - - These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR11_RSVD 0x0 - - Power Down Control - PSU_DDR_PHY_MR11_PDCTL 0x0 - - DQ Bus Receiver On-Die-Termination - PSU_DDR_PHY_MR11_DQODT 0x0 - - LPDDR4 Mode Register 11 - (OFFSET, MASK, VALUE) (0XFD0801AC, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_MR11_RESERVED_31_8_MASK | DDR_PHY_MR11_RSVD_MASK | DDR_PHY_MR11_PDCTL_MASK | DDR_PHY_MR11_DQODT_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_MR11_RESERVED_31_8_SHIFT - | 0x00000000U << DDR_PHY_MR11_RSVD_SHIFT - | 0x00000000U << DDR_PHY_MR11_PDCTL_SHIFT - | 0x00000000U << DDR_PHY_MR11_DQODT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR11_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MR12 @ 0XFD0801B0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR12_RESERVED_31_8 0x0 - - These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR12_RSVD 0x0 - - VREF_CA Range Select. - PSU_DDR_PHY_MR12_VR_CA 0x1 - - Controls the VREF(ca) levels for Frequency-Set-Point[1:0]. - PSU_DDR_PHY_MR12_VREF_CA 0xd - - LPDDR4 Mode Register 12 - (OFFSET, MASK, VALUE) (0XFD0801B0, 0xFFFFFFFFU ,0x0000004DU) - RegMask = (DDR_PHY_MR12_RESERVED_31_8_MASK | DDR_PHY_MR12_RSVD_MASK | DDR_PHY_MR12_VR_CA_MASK | DDR_PHY_MR12_VREF_CA_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_MR12_RESERVED_31_8_SHIFT - | 0x00000000U << DDR_PHY_MR12_RSVD_SHIFT - | 0x00000001U << DDR_PHY_MR12_VR_CA_SHIFT - | 0x0000000DU << DDR_PHY_MR12_VREF_CA_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR12_OFFSET ,0xFFFFFFFFU ,0x0000004DU); - /*############################################################################################################################ */ - - /*Register : MR13 @ 0XFD0801B4</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR13_RESERVED_31_8 0x0 - - Frequency Set Point Operation Mode - PSU_DDR_PHY_MR13_FSPOP 0x0 - - Frequency Set Point Write Enable - PSU_DDR_PHY_MR13_FSPWR 0x0 - - Data Mask Enable - PSU_DDR_PHY_MR13_DMD 0x0 - - Refresh Rate Option - PSU_DDR_PHY_MR13_RRO 0x0 - - VREF Current Generator - PSU_DDR_PHY_MR13_VRCG 0x1 - - VREF Output - PSU_DDR_PHY_MR13_VRO 0x0 - - Read Preamble Training Mode - PSU_DDR_PHY_MR13_RPT 0x0 - - Command Bus Training - PSU_DDR_PHY_MR13_CBT 0x0 - - LPDDR4 Mode Register 13 - (OFFSET, MASK, VALUE) (0XFD0801B4, 0xFFFFFFFFU ,0x00000008U) - RegMask = (DDR_PHY_MR13_RESERVED_31_8_MASK | DDR_PHY_MR13_FSPOP_MASK | DDR_PHY_MR13_FSPWR_MASK | DDR_PHY_MR13_DMD_MASK | DDR_PHY_MR13_RRO_MASK | DDR_PHY_MR13_VRCG_MASK | DDR_PHY_MR13_VRO_MASK | DDR_PHY_MR13_RPT_MASK | DDR_PHY_MR13_CBT_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_MR13_RESERVED_31_8_SHIFT - | 0x00000000U << DDR_PHY_MR13_FSPOP_SHIFT - | 0x00000000U << DDR_PHY_MR13_FSPWR_SHIFT - | 0x00000000U << DDR_PHY_MR13_DMD_SHIFT - | 0x00000000U << DDR_PHY_MR13_RRO_SHIFT - | 0x00000001U << DDR_PHY_MR13_VRCG_SHIFT - | 0x00000000U << DDR_PHY_MR13_VRO_SHIFT - | 0x00000000U << DDR_PHY_MR13_RPT_SHIFT - | 0x00000000U << DDR_PHY_MR13_CBT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR13_OFFSET ,0xFFFFFFFFU ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : MR14 @ 0XFD0801B8</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR14_RESERVED_31_8 0x0 - - These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR14_RSVD 0x0 - - VREFDQ Range Selects. - PSU_DDR_PHY_MR14_VR_DQ 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR14_VREF_DQ 0xd - - LPDDR4 Mode Register 14 - (OFFSET, MASK, VALUE) (0XFD0801B8, 0xFFFFFFFFU ,0x0000004DU) - RegMask = (DDR_PHY_MR14_RESERVED_31_8_MASK | DDR_PHY_MR14_RSVD_MASK | DDR_PHY_MR14_VR_DQ_MASK | DDR_PHY_MR14_VREF_DQ_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_MR14_RESERVED_31_8_SHIFT - | 0x00000000U << DDR_PHY_MR14_RSVD_SHIFT - | 0x00000001U << DDR_PHY_MR14_VR_DQ_SHIFT - | 0x0000000DU << DDR_PHY_MR14_VREF_DQ_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR14_OFFSET ,0xFFFFFFFFU ,0x0000004DU); - /*############################################################################################################################ */ - - /*Register : MR22 @ 0XFD0801D8</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_MR22_RESERVED_31_8 0x0 - - These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0. - PSU_DDR_PHY_MR22_RSVD 0x0 - - CA ODT termination disable. - PSU_DDR_PHY_MR22_ODTD_CA 0x0 - - ODT CS override. - PSU_DDR_PHY_MR22_ODTE_CS 0x0 - - ODT CK override. - PSU_DDR_PHY_MR22_ODTE_CK 0x0 - - Controller ODT value for VOH calibration. - PSU_DDR_PHY_MR22_CODT 0x0 - - LPDDR4 Mode Register 22 - (OFFSET, MASK, VALUE) (0XFD0801D8, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_MR22_RESERVED_31_8_MASK | DDR_PHY_MR22_RSVD_MASK | DDR_PHY_MR22_ODTD_CA_MASK | DDR_PHY_MR22_ODTE_CS_MASK | DDR_PHY_MR22_ODTE_CK_MASK | DDR_PHY_MR22_CODT_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_MR22_RESERVED_31_8_SHIFT - | 0x00000000U << DDR_PHY_MR22_RSVD_SHIFT - | 0x00000000U << DDR_PHY_MR22_ODTD_CA_SHIFT - | 0x00000000U << DDR_PHY_MR22_ODTE_CS_SHIFT - | 0x00000000U << DDR_PHY_MR22_ODTE_CK_SHIFT - | 0x00000000U << DDR_PHY_MR22_CODT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_MR22_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DTCR0 @ 0XFD080200</p> - - Refresh During Training - PSU_DDR_PHY_DTCR0_RFSHDT 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTCR0_RESERVED_27_26 0x0 - - Data Training Debug Rank Select - PSU_DDR_PHY_DTCR0_DTDRS 0x0 - - Data Training with Early/Extended Gate - PSU_DDR_PHY_DTCR0_DTEXG 0x0 - - Data Training Extended Write DQS - PSU_DDR_PHY_DTCR0_DTEXD 0x0 - - Data Training Debug Step - PSU_DDR_PHY_DTCR0_DTDSTP 0x0 - - Data Training Debug Enable - PSU_DDR_PHY_DTCR0_DTDEN 0x0 - - Data Training Debug Byte Select - PSU_DDR_PHY_DTCR0_DTDBS 0x0 - - Data Training read DBI deskewing configuration - PSU_DDR_PHY_DTCR0_DTRDBITR 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTCR0_RESERVED_13 0x0 - - Data Training Write Bit Deskew Data Mask - PSU_DDR_PHY_DTCR0_DTWBDDM 0x1 - - Refreshes Issued During Entry to Training - PSU_DDR_PHY_DTCR0_RFSHEN 0x1 - - Data Training Compare Data - PSU_DDR_PHY_DTCR0_DTCMPD 0x1 - - Data Training Using MPR - PSU_DDR_PHY_DTCR0_DTMPR 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTCR0_RESERVED_5_4 0x0 - - Data Training Repeat Number - PSU_DDR_PHY_DTCR0_DTRPTN 0x7 - - Data Training Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080200, 0xFFFFFFFFU ,0x800091C7U) - RegMask = (DDR_PHY_DTCR0_RFSHDT_MASK | DDR_PHY_DTCR0_RESERVED_27_26_MASK | DDR_PHY_DTCR0_DTDRS_MASK | DDR_PHY_DTCR0_DTEXG_MASK | DDR_PHY_DTCR0_DTEXD_MASK | DDR_PHY_DTCR0_DTDSTP_MASK | DDR_PHY_DTCR0_DTDEN_MASK | DDR_PHY_DTCR0_DTDBS_MASK | DDR_PHY_DTCR0_DTRDBITR_MASK | DDR_PHY_DTCR0_RESERVED_13_MASK | DDR_PHY_DTCR0_DTWBDDM_MASK | DDR_PHY_DTCR0_RFSHEN_MASK | DDR_PHY_DTCR0_DTCMPD_MASK | DDR_PHY_DTCR0_DTMPR_MASK | DDR_PHY_DTCR0_RESERVED_5_4_MASK | DDR_PHY_DTCR0_DTRPTN_MASK | 0 ); - - RegVal = ((0x00000008U << DDR_PHY_DTCR0_RFSHDT_SHIFT - | 0x00000000U << DDR_PHY_DTCR0_RESERVED_27_26_SHIFT - | 0x00000000U << DDR_PHY_DTCR0_DTDRS_SHIFT - | 0x00000000U << DDR_PHY_DTCR0_DTEXG_SHIFT - | 0x00000000U << DDR_PHY_DTCR0_DTEXD_SHIFT - | 0x00000000U << DDR_PHY_DTCR0_DTDSTP_SHIFT - | 0x00000000U << DDR_PHY_DTCR0_DTDEN_SHIFT - | 0x00000000U << DDR_PHY_DTCR0_DTDBS_SHIFT - | 0x00000002U << DDR_PHY_DTCR0_DTRDBITR_SHIFT - | 0x00000000U << DDR_PHY_DTCR0_RESERVED_13_SHIFT - | 0x00000001U << DDR_PHY_DTCR0_DTWBDDM_SHIFT - | 0x00000001U << DDR_PHY_DTCR0_RFSHEN_SHIFT - | 0x00000001U << DDR_PHY_DTCR0_DTCMPD_SHIFT - | 0x00000001U << DDR_PHY_DTCR0_DTMPR_SHIFT - | 0x00000000U << DDR_PHY_DTCR0_RESERVED_5_4_SHIFT - | 0x00000007U << DDR_PHY_DTCR0_DTRPTN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DTCR0_OFFSET ,0xFFFFFFFFU ,0x800091C7U); - /*############################################################################################################################ */ - - /*Register : DTCR1 @ 0XFD080204</p> - - Rank Enable. - PSU_DDR_PHY_DTCR1_RANKEN_RSVD 0x0 - - Rank Enable. - PSU_DDR_PHY_DTCR1_RANKEN 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTCR1_RESERVED_15_14 0x0 - - Data Training Rank - PSU_DDR_PHY_DTCR1_DTRANK 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTCR1_RESERVED_11 0x0 - - Read Leveling Gate Sampling Difference - PSU_DDR_PHY_DTCR1_RDLVLGDIFF 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTCR1_RESERVED_7 0x0 - - Read Leveling Gate Shift - PSU_DDR_PHY_DTCR1_RDLVLGS 0x3 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DTCR1_RESERVED_3 0x0 - - Read Preamble Training enable - PSU_DDR_PHY_DTCR1_RDPRMVL_TRN 0x1 - - Read Leveling Enable - PSU_DDR_PHY_DTCR1_RDLVLEN 0x1 - - Basic Gate Training Enable - PSU_DDR_PHY_DTCR1_BSTEN 0x0 - - Data Training Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD080204, 0xFFFFFFFFU ,0x00010236U) - RegMask = (DDR_PHY_DTCR1_RANKEN_RSVD_MASK | DDR_PHY_DTCR1_RANKEN_MASK | DDR_PHY_DTCR1_RESERVED_15_14_MASK | DDR_PHY_DTCR1_DTRANK_MASK | DDR_PHY_DTCR1_RESERVED_11_MASK | DDR_PHY_DTCR1_RDLVLGDIFF_MASK | DDR_PHY_DTCR1_RESERVED_7_MASK | DDR_PHY_DTCR1_RDLVLGS_MASK | DDR_PHY_DTCR1_RESERVED_3_MASK | DDR_PHY_DTCR1_RDPRMVL_TRN_MASK | DDR_PHY_DTCR1_RDLVLEN_MASK | DDR_PHY_DTCR1_BSTEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DTCR1_RANKEN_RSVD_SHIFT - | 0x00000001U << DDR_PHY_DTCR1_RANKEN_SHIFT - | 0x00000000U << DDR_PHY_DTCR1_RESERVED_15_14_SHIFT - | 0x00000000U << DDR_PHY_DTCR1_DTRANK_SHIFT - | 0x00000000U << DDR_PHY_DTCR1_RESERVED_11_SHIFT - | 0x00000002U << DDR_PHY_DTCR1_RDLVLGDIFF_SHIFT - | 0x00000000U << DDR_PHY_DTCR1_RESERVED_7_SHIFT - | 0x00000003U << DDR_PHY_DTCR1_RDLVLGS_SHIFT - | 0x00000000U << DDR_PHY_DTCR1_RESERVED_3_SHIFT - | 0x00000001U << DDR_PHY_DTCR1_RDPRMVL_TRN_SHIFT - | 0x00000001U << DDR_PHY_DTCR1_RDLVLEN_SHIFT - | 0x00000000U << DDR_PHY_DTCR1_BSTEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DTCR1_OFFSET ,0xFFFFFFFFU ,0x00010236U); - /*############################################################################################################################ */ - - /*Register : CATR0 @ 0XFD080240</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_CATR0_RESERVED_31_21 0x0 - - Minimum time (in terms of number of dram clocks) between two consectuve CA calibration command - PSU_DDR_PHY_CATR0_CACD 0x14 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_CATR0_RESERVED_15_13 0x0 - - Minimum time (in terms of number of dram clocks) PUB should wait before sampling the CA response after Calibration command ha - been sent to the memory - PSU_DDR_PHY_CATR0_CAADR 0x10 - - CA_1 Response Byte Lane 1 - PSU_DDR_PHY_CATR0_CA1BYTE1 0x5 - - CA_1 Response Byte Lane 0 - PSU_DDR_PHY_CATR0_CA1BYTE0 0x4 - - CA Training Register 0 - (OFFSET, MASK, VALUE) (0XFD080240, 0xFFFFFFFFU ,0x00141054U) - RegMask = (DDR_PHY_CATR0_RESERVED_31_21_MASK | DDR_PHY_CATR0_CACD_MASK | DDR_PHY_CATR0_RESERVED_15_13_MASK | DDR_PHY_CATR0_CAADR_MASK | DDR_PHY_CATR0_CA1BYTE1_MASK | DDR_PHY_CATR0_CA1BYTE0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_CATR0_RESERVED_31_21_SHIFT - | 0x00000014U << DDR_PHY_CATR0_CACD_SHIFT - | 0x00000000U << DDR_PHY_CATR0_RESERVED_15_13_SHIFT - | 0x00000010U << DDR_PHY_CATR0_CAADR_SHIFT - | 0x00000005U << DDR_PHY_CATR0_CA1BYTE1_SHIFT - | 0x00000004U << DDR_PHY_CATR0_CA1BYTE0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_CATR0_OFFSET ,0xFFFFFFFFU ,0x00141054U); - /*############################################################################################################################ */ - - /*Register : BISTLSR @ 0XFD080414</p> - - LFSR seed for pseudo-random BIST patterns - PSU_DDR_PHY_BISTLSR_SEED 0x12341000 - - BIST LFSR Seed Register - (OFFSET, MASK, VALUE) (0XFD080414, 0xFFFFFFFFU ,0x12341000U) - RegMask = (DDR_PHY_BISTLSR_SEED_MASK | 0 ); - - RegVal = ((0x12341000U << DDR_PHY_BISTLSR_SEED_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_BISTLSR_OFFSET ,0xFFFFFFFFU ,0x12341000U); - /*############################################################################################################################ */ - - /*Register : RIOCR5 @ 0XFD0804F4</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_RIOCR5_RESERVED_31_16 0x0 - - Reserved. Return zeros on reads. - PSU_DDR_PHY_RIOCR5_ODTOEMODE_RSVD 0x0 - - SDRAM On-die Termination Output Enable (OE) Mode Selection. - PSU_DDR_PHY_RIOCR5_ODTOEMODE 0x5 - - Rank I/O Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD0804F4, 0xFFFFFFFFU ,0x00000005U) - RegMask = (DDR_PHY_RIOCR5_RESERVED_31_16_MASK | DDR_PHY_RIOCR5_ODTOEMODE_RSVD_MASK | DDR_PHY_RIOCR5_ODTOEMODE_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_RIOCR5_RESERVED_31_16_SHIFT - | 0x00000000U << DDR_PHY_RIOCR5_ODTOEMODE_RSVD_SHIFT - | 0x00000005U << DDR_PHY_RIOCR5_ODTOEMODE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_RIOCR5_OFFSET ,0xFFFFFFFFU ,0x00000005U); - /*############################################################################################################################ */ - - /*Register : ACIOCR0 @ 0XFD080500</p> - - Address/Command Slew Rate (D3F I/O Only) - PSU_DDR_PHY_ACIOCR0_ACSR 0x0 - - SDRAM Reset I/O Mode - PSU_DDR_PHY_ACIOCR0_RSTIOM 0x1 - - SDRAM Reset Power Down Receiver - PSU_DDR_PHY_ACIOCR0_RSTPDR 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACIOCR0_RESERVED_27 0x0 - - SDRAM Reset On-Die Termination - PSU_DDR_PHY_ACIOCR0_RSTODT 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACIOCR0_RESERVED_25_10 0x0 - - CK Duty Cycle Correction - PSU_DDR_PHY_ACIOCR0_CKDCC 0x0 - - AC Power Down Receiver Mode - PSU_DDR_PHY_ACIOCR0_ACPDRMODE 0x2 - - AC On-die Termination Mode - PSU_DDR_PHY_ACIOCR0_ACODTMODE 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACIOCR0_RESERVED_1 0x0 - - Control delayed or non-delayed clock to CS_N/ODT?CKE AC slices. - PSU_DDR_PHY_ACIOCR0_ACRANKCLKSEL 0x0 - - AC I/O Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080500, 0xFFFFFFFFU ,0x30000028U) - RegMask = (DDR_PHY_ACIOCR0_ACSR_MASK | DDR_PHY_ACIOCR0_RSTIOM_MASK | DDR_PHY_ACIOCR0_RSTPDR_MASK | DDR_PHY_ACIOCR0_RESERVED_27_MASK | DDR_PHY_ACIOCR0_RSTODT_MASK | DDR_PHY_ACIOCR0_RESERVED_25_10_MASK | DDR_PHY_ACIOCR0_CKDCC_MASK | DDR_PHY_ACIOCR0_ACPDRMODE_MASK | DDR_PHY_ACIOCR0_ACODTMODE_MASK | DDR_PHY_ACIOCR0_RESERVED_1_MASK | DDR_PHY_ACIOCR0_ACRANKCLKSEL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ACIOCR0_ACSR_SHIFT - | 0x00000001U << DDR_PHY_ACIOCR0_RSTIOM_SHIFT - | 0x00000001U << DDR_PHY_ACIOCR0_RSTPDR_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR0_RESERVED_27_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR0_RSTODT_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR0_RESERVED_25_10_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR0_CKDCC_SHIFT - | 0x00000002U << DDR_PHY_ACIOCR0_ACPDRMODE_SHIFT - | 0x00000002U << DDR_PHY_ACIOCR0_ACODTMODE_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR0_RESERVED_1_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR0_ACRANKCLKSEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ACIOCR0_OFFSET ,0xFFFFFFFFU ,0x30000028U); - /*############################################################################################################################ */ - - /*Register : ACIOCR2 @ 0XFD080508</p> - - Clock gating for glue logic inside CLKGEN and glue logic inside CONTROL slice - PSU_DDR_PHY_ACIOCR2_CLKGENCLKGATE 0x0 - - Clock gating for Output Enable D slices [0] - PSU_DDR_PHY_ACIOCR2_ACOECLKGATE0 0x0 - - Clock gating for Power Down Receiver D slices [0] - PSU_DDR_PHY_ACIOCR2_ACPDRCLKGATE0 0x0 - - Clock gating for Termination Enable D slices [0] - PSU_DDR_PHY_ACIOCR2_ACTECLKGATE0 0x0 - - Clock gating for CK# D slices [1:0] - PSU_DDR_PHY_ACIOCR2_CKNCLKGATE0 0x2 - - Clock gating for CK D slices [1:0] - PSU_DDR_PHY_ACIOCR2_CKCLKGATE0 0x2 - - Clock gating for AC D slices [23:0] - PSU_DDR_PHY_ACIOCR2_ACCLKGATE0 0x0 - - AC I/O Configuration Register 2 - (OFFSET, MASK, VALUE) (0XFD080508, 0xFFFFFFFFU ,0x0A000000U) - RegMask = (DDR_PHY_ACIOCR2_CLKGENCLKGATE_MASK | DDR_PHY_ACIOCR2_ACOECLKGATE0_MASK | DDR_PHY_ACIOCR2_ACPDRCLKGATE0_MASK | DDR_PHY_ACIOCR2_ACTECLKGATE0_MASK | DDR_PHY_ACIOCR2_CKNCLKGATE0_MASK | DDR_PHY_ACIOCR2_CKCLKGATE0_MASK | DDR_PHY_ACIOCR2_ACCLKGATE0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ACIOCR2_CLKGENCLKGATE_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR2_ACOECLKGATE0_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR2_ACPDRCLKGATE0_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR2_ACTECLKGATE0_SHIFT - | 0x00000002U << DDR_PHY_ACIOCR2_CKNCLKGATE0_SHIFT - | 0x00000002U << DDR_PHY_ACIOCR2_CKCLKGATE0_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR2_ACCLKGATE0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ACIOCR2_OFFSET ,0xFFFFFFFFU ,0x0A000000U); - /*############################################################################################################################ */ - - /*Register : ACIOCR3 @ 0XFD08050C</p> - - SDRAM Parity Output Enable (OE) Mode Selection - PSU_DDR_PHY_ACIOCR3_PAROEMODE 0x0 - - SDRAM Bank Group Output Enable (OE) Mode Selection - PSU_DDR_PHY_ACIOCR3_BGOEMODE 0x0 - - SDRAM Bank Address Output Enable (OE) Mode Selection - PSU_DDR_PHY_ACIOCR3_BAOEMODE 0x0 - - SDRAM A[17] Output Enable (OE) Mode Selection - PSU_DDR_PHY_ACIOCR3_A17OEMODE 0x0 - - SDRAM A[16] / RAS_n Output Enable (OE) Mode Selection - PSU_DDR_PHY_ACIOCR3_A16OEMODE 0x0 - - SDRAM ACT_n Output Enable (OE) Mode Selection (DDR4 only) - PSU_DDR_PHY_ACIOCR3_ACTOEMODE 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACIOCR3_RESERVED_15_8 0x0 - - Reserved. Return zeros on reads. - PSU_DDR_PHY_ACIOCR3_CKOEMODE_RSVD 0x0 - - SDRAM CK Output Enable (OE) Mode Selection. - PSU_DDR_PHY_ACIOCR3_CKOEMODE 0x9 - - AC I/O Configuration Register 3 - (OFFSET, MASK, VALUE) (0XFD08050C, 0xFFFFFFFFU ,0x00000009U) - RegMask = (DDR_PHY_ACIOCR3_PAROEMODE_MASK | DDR_PHY_ACIOCR3_BGOEMODE_MASK | DDR_PHY_ACIOCR3_BAOEMODE_MASK | DDR_PHY_ACIOCR3_A17OEMODE_MASK | DDR_PHY_ACIOCR3_A16OEMODE_MASK | DDR_PHY_ACIOCR3_ACTOEMODE_MASK | DDR_PHY_ACIOCR3_RESERVED_15_8_MASK | DDR_PHY_ACIOCR3_CKOEMODE_RSVD_MASK | DDR_PHY_ACIOCR3_CKOEMODE_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ACIOCR3_PAROEMODE_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR3_BGOEMODE_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR3_BAOEMODE_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR3_A17OEMODE_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR3_A16OEMODE_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR3_ACTOEMODE_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR3_RESERVED_15_8_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR3_CKOEMODE_RSVD_SHIFT - | 0x00000009U << DDR_PHY_ACIOCR3_CKOEMODE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ACIOCR3_OFFSET ,0xFFFFFFFFU ,0x00000009U); - /*############################################################################################################################ */ - - /*Register : ACIOCR4 @ 0XFD080510</p> - - Clock gating for AC LB slices and loopback read valid slices - PSU_DDR_PHY_ACIOCR4_LBCLKGATE 0x0 - - Clock gating for Output Enable D slices [1] - PSU_DDR_PHY_ACIOCR4_ACOECLKGATE1 0x0 - - Clock gating for Power Down Receiver D slices [1] - PSU_DDR_PHY_ACIOCR4_ACPDRCLKGATE1 0x0 - - Clock gating for Termination Enable D slices [1] - PSU_DDR_PHY_ACIOCR4_ACTECLKGATE1 0x0 - - Clock gating for CK# D slices [3:2] - PSU_DDR_PHY_ACIOCR4_CKNCLKGATE1 0x2 - - Clock gating for CK D slices [3:2] - PSU_DDR_PHY_ACIOCR4_CKCLKGATE1 0x2 - - Clock gating for AC D slices [47:24] - PSU_DDR_PHY_ACIOCR4_ACCLKGATE1 0x0 - - AC I/O Configuration Register 4 - (OFFSET, MASK, VALUE) (0XFD080510, 0xFFFFFFFFU ,0x0A000000U) - RegMask = (DDR_PHY_ACIOCR4_LBCLKGATE_MASK | DDR_PHY_ACIOCR4_ACOECLKGATE1_MASK | DDR_PHY_ACIOCR4_ACPDRCLKGATE1_MASK | DDR_PHY_ACIOCR4_ACTECLKGATE1_MASK | DDR_PHY_ACIOCR4_CKNCLKGATE1_MASK | DDR_PHY_ACIOCR4_CKCLKGATE1_MASK | DDR_PHY_ACIOCR4_ACCLKGATE1_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ACIOCR4_LBCLKGATE_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR4_ACOECLKGATE1_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR4_ACPDRCLKGATE1_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR4_ACTECLKGATE1_SHIFT - | 0x00000002U << DDR_PHY_ACIOCR4_CKNCLKGATE1_SHIFT - | 0x00000002U << DDR_PHY_ACIOCR4_CKCLKGATE1_SHIFT - | 0x00000000U << DDR_PHY_ACIOCR4_ACCLKGATE1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ACIOCR4_OFFSET ,0xFFFFFFFFU ,0x0A000000U); - /*############################################################################################################################ */ - - /*Register : IOVCR0 @ 0XFD080520</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_IOVCR0_RESERVED_31_29 0x0 - - Address/command lane VREF Pad Enable - PSU_DDR_PHY_IOVCR0_ACREFPEN 0x0 - - Address/command lane Internal VREF Enable - PSU_DDR_PHY_IOVCR0_ACREFEEN 0x0 - - Address/command lane Single-End VREF Enable - PSU_DDR_PHY_IOVCR0_ACREFSEN 0x1 - - Address/command lane Internal VREF Enable - PSU_DDR_PHY_IOVCR0_ACREFIEN 0x1 - - External VREF generato REFSEL range select - PSU_DDR_PHY_IOVCR0_ACREFESELRANGE 0x0 - - Address/command lane External VREF Select - PSU_DDR_PHY_IOVCR0_ACREFESEL 0x0 - - Single ended VREF generator REFSEL range select - PSU_DDR_PHY_IOVCR0_ACREFSSELRANGE 0x1 - - Address/command lane Single-End VREF Select - PSU_DDR_PHY_IOVCR0_ACREFSSEL 0x30 - - Internal VREF generator REFSEL ragne select - PSU_DDR_PHY_IOVCR0_ACVREFISELRANGE 0x1 - - REFSEL Control for internal AC IOs - PSU_DDR_PHY_IOVCR0_ACVREFISEL 0x30 - - IO VREF Control Register 0 - (OFFSET, MASK, VALUE) (0XFD080520, 0xFFFFFFFFU ,0x0300B0B0U) - RegMask = (DDR_PHY_IOVCR0_RESERVED_31_29_MASK | DDR_PHY_IOVCR0_ACREFPEN_MASK | DDR_PHY_IOVCR0_ACREFEEN_MASK | DDR_PHY_IOVCR0_ACREFSEN_MASK | DDR_PHY_IOVCR0_ACREFIEN_MASK | DDR_PHY_IOVCR0_ACREFESELRANGE_MASK | DDR_PHY_IOVCR0_ACREFESEL_MASK | DDR_PHY_IOVCR0_ACREFSSELRANGE_MASK | DDR_PHY_IOVCR0_ACREFSSEL_MASK | DDR_PHY_IOVCR0_ACVREFISELRANGE_MASK | DDR_PHY_IOVCR0_ACVREFISEL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_IOVCR0_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_IOVCR0_ACREFPEN_SHIFT - | 0x00000000U << DDR_PHY_IOVCR0_ACREFEEN_SHIFT - | 0x00000001U << DDR_PHY_IOVCR0_ACREFSEN_SHIFT - | 0x00000001U << DDR_PHY_IOVCR0_ACREFIEN_SHIFT - | 0x00000000U << DDR_PHY_IOVCR0_ACREFESELRANGE_SHIFT - | 0x00000000U << DDR_PHY_IOVCR0_ACREFESEL_SHIFT - | 0x00000001U << DDR_PHY_IOVCR0_ACREFSSELRANGE_SHIFT - | 0x00000030U << DDR_PHY_IOVCR0_ACREFSSEL_SHIFT - | 0x00000001U << DDR_PHY_IOVCR0_ACVREFISELRANGE_SHIFT - | 0x00000030U << DDR_PHY_IOVCR0_ACVREFISEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_IOVCR0_OFFSET ,0xFFFFFFFFU ,0x0300B0B0U); - /*############################################################################################################################ */ - - /*Register : VTCR0 @ 0XFD080528</p> - - Number of ctl_clk required to meet (> 150ns) timing requirements during DRAM DQ VREF training - PSU_DDR_PHY_VTCR0_TVREF 0x7 - - DRM DQ VREF training Enable - PSU_DDR_PHY_VTCR0_DVEN 0x1 - - Per Device Addressability Enable - PSU_DDR_PHY_VTCR0_PDAEN 0x1 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_VTCR0_RESERVED_26 0x0 - - VREF Word Count - PSU_DDR_PHY_VTCR0_VWCR 0x4 - - DRAM DQ VREF step size used during DRAM VREF training - PSU_DDR_PHY_VTCR0_DVSS 0x0 - - Maximum VREF limit value used during DRAM VREF training - PSU_DDR_PHY_VTCR0_DVMAX 0x32 - - Minimum VREF limit value used during DRAM VREF training - PSU_DDR_PHY_VTCR0_DVMIN 0x0 - - Initial DRAM DQ VREF value used during DRAM VREF training - PSU_DDR_PHY_VTCR0_DVINIT 0x19 - - VREF Training Control Register 0 - (OFFSET, MASK, VALUE) (0XFD080528, 0xFFFFFFFFU ,0xF9032019U) - RegMask = (DDR_PHY_VTCR0_TVREF_MASK | DDR_PHY_VTCR0_DVEN_MASK | DDR_PHY_VTCR0_PDAEN_MASK | DDR_PHY_VTCR0_RESERVED_26_MASK | DDR_PHY_VTCR0_VWCR_MASK | DDR_PHY_VTCR0_DVSS_MASK | DDR_PHY_VTCR0_DVMAX_MASK | DDR_PHY_VTCR0_DVMIN_MASK | DDR_PHY_VTCR0_DVINIT_MASK | 0 ); - - RegVal = ((0x00000007U << DDR_PHY_VTCR0_TVREF_SHIFT - | 0x00000001U << DDR_PHY_VTCR0_DVEN_SHIFT - | 0x00000001U << DDR_PHY_VTCR0_PDAEN_SHIFT - | 0x00000000U << DDR_PHY_VTCR0_RESERVED_26_SHIFT - | 0x00000004U << DDR_PHY_VTCR0_VWCR_SHIFT - | 0x00000000U << DDR_PHY_VTCR0_DVSS_SHIFT - | 0x00000032U << DDR_PHY_VTCR0_DVMAX_SHIFT - | 0x00000000U << DDR_PHY_VTCR0_DVMIN_SHIFT - | 0x00000019U << DDR_PHY_VTCR0_DVINIT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_VTCR0_OFFSET ,0xFFFFFFFFU ,0xF9032019U); - /*############################################################################################################################ */ - - /*Register : VTCR1 @ 0XFD08052C</p> - - Host VREF step size used during VREF training. The register value of N indicates step size of (N+1) - PSU_DDR_PHY_VTCR1_HVSS 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_VTCR1_RESERVED_27 0x0 - - Maximum VREF limit value used during DRAM VREF training. - PSU_DDR_PHY_VTCR1_HVMAX 0x7f - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_VTCR1_RESERVED_19 0x0 - - Minimum VREF limit value used during DRAM VREF training. - PSU_DDR_PHY_VTCR1_HVMIN 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_VTCR1_RESERVED_11 0x0 - - Static Host Vref Rank Value - PSU_DDR_PHY_VTCR1_SHRNK 0x0 - - Static Host Vref Rank Enable - PSU_DDR_PHY_VTCR1_SHREN 0x1 - - Number of ctl_clk required to meet (> 200ns) VREF Settling timing requirements during Host IO VREF training - PSU_DDR_PHY_VTCR1_TVREFIO 0x7 - - Eye LCDL Offset value for VREF training - PSU_DDR_PHY_VTCR1_EOFF 0x0 - - Number of LCDL Eye points for which VREF training is repeated - PSU_DDR_PHY_VTCR1_ENUM 0x0 - - HOST (IO) internal VREF training Enable - PSU_DDR_PHY_VTCR1_HVEN 0x1 - - Host IO Type Control - PSU_DDR_PHY_VTCR1_HVIO 0x1 - - VREF Training Control Register 1 - (OFFSET, MASK, VALUE) (0XFD08052C, 0xFFFFFFFFU ,0x07F001E3U) - RegMask = (DDR_PHY_VTCR1_HVSS_MASK | DDR_PHY_VTCR1_RESERVED_27_MASK | DDR_PHY_VTCR1_HVMAX_MASK | DDR_PHY_VTCR1_RESERVED_19_MASK | DDR_PHY_VTCR1_HVMIN_MASK | DDR_PHY_VTCR1_RESERVED_11_MASK | DDR_PHY_VTCR1_SHRNK_MASK | DDR_PHY_VTCR1_SHREN_MASK | DDR_PHY_VTCR1_TVREFIO_MASK | DDR_PHY_VTCR1_EOFF_MASK | DDR_PHY_VTCR1_ENUM_MASK | DDR_PHY_VTCR1_HVEN_MASK | DDR_PHY_VTCR1_HVIO_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_VTCR1_HVSS_SHIFT - | 0x00000000U << DDR_PHY_VTCR1_RESERVED_27_SHIFT - | 0x0000007FU << DDR_PHY_VTCR1_HVMAX_SHIFT - | 0x00000000U << DDR_PHY_VTCR1_RESERVED_19_SHIFT - | 0x00000000U << DDR_PHY_VTCR1_HVMIN_SHIFT - | 0x00000000U << DDR_PHY_VTCR1_RESERVED_11_SHIFT - | 0x00000000U << DDR_PHY_VTCR1_SHRNK_SHIFT - | 0x00000001U << DDR_PHY_VTCR1_SHREN_SHIFT - | 0x00000007U << DDR_PHY_VTCR1_TVREFIO_SHIFT - | 0x00000000U << DDR_PHY_VTCR1_EOFF_SHIFT - | 0x00000000U << DDR_PHY_VTCR1_ENUM_SHIFT - | 0x00000001U << DDR_PHY_VTCR1_HVEN_SHIFT - | 0x00000001U << DDR_PHY_VTCR1_HVIO_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_VTCR1_OFFSET ,0xFFFFFFFFU ,0x07F001E3U); - /*############################################################################################################################ */ - - /*Register : ACBDLR1 @ 0XFD080544</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR1_RESERVED_31_30 0x0 - - Delay select for the BDL on Parity. - PSU_DDR_PHY_ACBDLR1_PARBD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR1_RESERVED_23_22 0x0 - - Delay select for the BDL on Address A[16]. In DDR3 mode this pin is connected to WE. - PSU_DDR_PHY_ACBDLR1_A16BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR1_RESERVED_15_14 0x0 - - Delay select for the BDL on Address A[17]. When not in DDR4 modemode this pin is connected to CAS. - PSU_DDR_PHY_ACBDLR1_A17BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR1_RESERVED_7_6 0x0 - - Delay select for the BDL on ACTN. - PSU_DDR_PHY_ACBDLR1_ACTBD 0x0 - - AC Bit Delay Line Register 1 - (OFFSET, MASK, VALUE) (0XFD080544, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_ACBDLR1_RESERVED_31_30_MASK | DDR_PHY_ACBDLR1_PARBD_MASK | DDR_PHY_ACBDLR1_RESERVED_23_22_MASK | DDR_PHY_ACBDLR1_A16BD_MASK | DDR_PHY_ACBDLR1_RESERVED_15_14_MASK | DDR_PHY_ACBDLR1_A17BD_MASK | DDR_PHY_ACBDLR1_RESERVED_7_6_MASK | DDR_PHY_ACBDLR1_ACTBD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ACBDLR1_RESERVED_31_30_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR1_PARBD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR1_RESERVED_23_22_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR1_A16BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR1_RESERVED_15_14_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR1_A17BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR1_RESERVED_7_6_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR1_ACTBD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ACBDLR1_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : ACBDLR2 @ 0XFD080548</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR2_RESERVED_31_30 0x0 - - Delay select for the BDL on BG[1]. - PSU_DDR_PHY_ACBDLR2_BG1BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR2_RESERVED_23_22 0x0 - - Delay select for the BDL on BG[0]. - PSU_DDR_PHY_ACBDLR2_BG0BD 0x0 - - Reser.ved Return zeroes on reads. - PSU_DDR_PHY_ACBDLR2_RESERVED_15_14 0x0 - - Delay select for the BDL on BA[1]. - PSU_DDR_PHY_ACBDLR2_BA1BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR2_RESERVED_7_6 0x0 - - Delay select for the BDL on BA[0]. - PSU_DDR_PHY_ACBDLR2_BA0BD 0x0 - - AC Bit Delay Line Register 2 - (OFFSET, MASK, VALUE) (0XFD080548, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_ACBDLR2_RESERVED_31_30_MASK | DDR_PHY_ACBDLR2_BG1BD_MASK | DDR_PHY_ACBDLR2_RESERVED_23_22_MASK | DDR_PHY_ACBDLR2_BG0BD_MASK | DDR_PHY_ACBDLR2_RESERVED_15_14_MASK | DDR_PHY_ACBDLR2_BA1BD_MASK | DDR_PHY_ACBDLR2_RESERVED_7_6_MASK | DDR_PHY_ACBDLR2_BA0BD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ACBDLR2_RESERVED_31_30_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR2_BG1BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR2_RESERVED_23_22_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR2_BG0BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR2_RESERVED_15_14_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR2_BA1BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR2_RESERVED_7_6_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR2_BA0BD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ACBDLR2_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : ACBDLR6 @ 0XFD080558</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR6_RESERVED_31_30 0x0 - - Delay select for the BDL on Address A[3]. - PSU_DDR_PHY_ACBDLR6_A03BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR6_RESERVED_23_22 0x0 - - Delay select for the BDL on Address A[2]. - PSU_DDR_PHY_ACBDLR6_A02BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR6_RESERVED_15_14 0x0 - - Delay select for the BDL on Address A[1]. - PSU_DDR_PHY_ACBDLR6_A01BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR6_RESERVED_7_6 0x0 - - Delay select for the BDL on Address A[0]. - PSU_DDR_PHY_ACBDLR6_A00BD 0x0 - - AC Bit Delay Line Register 6 - (OFFSET, MASK, VALUE) (0XFD080558, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_ACBDLR6_RESERVED_31_30_MASK | DDR_PHY_ACBDLR6_A03BD_MASK | DDR_PHY_ACBDLR6_RESERVED_23_22_MASK | DDR_PHY_ACBDLR6_A02BD_MASK | DDR_PHY_ACBDLR6_RESERVED_15_14_MASK | DDR_PHY_ACBDLR6_A01BD_MASK | DDR_PHY_ACBDLR6_RESERVED_7_6_MASK | DDR_PHY_ACBDLR6_A00BD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ACBDLR6_RESERVED_31_30_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR6_A03BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR6_RESERVED_23_22_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR6_A02BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR6_RESERVED_15_14_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR6_A01BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR6_RESERVED_7_6_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR6_A00BD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ACBDLR6_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : ACBDLR7 @ 0XFD08055C</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR7_RESERVED_31_30 0x0 - - Delay select for the BDL on Address A[7]. - PSU_DDR_PHY_ACBDLR7_A07BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR7_RESERVED_23_22 0x0 - - Delay select for the BDL on Address A[6]. - PSU_DDR_PHY_ACBDLR7_A06BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR7_RESERVED_15_14 0x0 - - Delay select for the BDL on Address A[5]. - PSU_DDR_PHY_ACBDLR7_A05BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR7_RESERVED_7_6 0x0 - - Delay select for the BDL on Address A[4]. - PSU_DDR_PHY_ACBDLR7_A04BD 0x0 - - AC Bit Delay Line Register 7 - (OFFSET, MASK, VALUE) (0XFD08055C, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_ACBDLR7_RESERVED_31_30_MASK | DDR_PHY_ACBDLR7_A07BD_MASK | DDR_PHY_ACBDLR7_RESERVED_23_22_MASK | DDR_PHY_ACBDLR7_A06BD_MASK | DDR_PHY_ACBDLR7_RESERVED_15_14_MASK | DDR_PHY_ACBDLR7_A05BD_MASK | DDR_PHY_ACBDLR7_RESERVED_7_6_MASK | DDR_PHY_ACBDLR7_A04BD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ACBDLR7_RESERVED_31_30_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR7_A07BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR7_RESERVED_23_22_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR7_A06BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR7_RESERVED_15_14_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR7_A05BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR7_RESERVED_7_6_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR7_A04BD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ACBDLR7_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : ACBDLR8 @ 0XFD080560</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR8_RESERVED_31_30 0x0 - - Delay select for the BDL on Address A[11]. - PSU_DDR_PHY_ACBDLR8_A11BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR8_RESERVED_23_22 0x0 - - Delay select for the BDL on Address A[10]. - PSU_DDR_PHY_ACBDLR8_A10BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR8_RESERVED_15_14 0x0 - - Delay select for the BDL on Address A[9]. - PSU_DDR_PHY_ACBDLR8_A09BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR8_RESERVED_7_6 0x0 - - Delay select for the BDL on Address A[8]. - PSU_DDR_PHY_ACBDLR8_A08BD 0x0 - - AC Bit Delay Line Register 8 - (OFFSET, MASK, VALUE) (0XFD080560, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_ACBDLR8_RESERVED_31_30_MASK | DDR_PHY_ACBDLR8_A11BD_MASK | DDR_PHY_ACBDLR8_RESERVED_23_22_MASK | DDR_PHY_ACBDLR8_A10BD_MASK | DDR_PHY_ACBDLR8_RESERVED_15_14_MASK | DDR_PHY_ACBDLR8_A09BD_MASK | DDR_PHY_ACBDLR8_RESERVED_7_6_MASK | DDR_PHY_ACBDLR8_A08BD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ACBDLR8_RESERVED_31_30_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR8_A11BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR8_RESERVED_23_22_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR8_A10BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR8_RESERVED_15_14_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR8_A09BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR8_RESERVED_7_6_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR8_A08BD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ACBDLR8_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : ACBDLR9 @ 0XFD080564</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR9_RESERVED_31_30 0x0 - - Delay select for the BDL on Address A[15]. - PSU_DDR_PHY_ACBDLR9_A15BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR9_RESERVED_23_22 0x0 - - Delay select for the BDL on Address A[14]. - PSU_DDR_PHY_ACBDLR9_A14BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR9_RESERVED_15_14 0x0 - - Delay select for the BDL on Address A[13]. - PSU_DDR_PHY_ACBDLR9_A13BD 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ACBDLR9_RESERVED_7_6 0x0 - - Delay select for the BDL on Address A[12]. - PSU_DDR_PHY_ACBDLR9_A12BD 0x0 - - AC Bit Delay Line Register 9 - (OFFSET, MASK, VALUE) (0XFD080564, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_ACBDLR9_RESERVED_31_30_MASK | DDR_PHY_ACBDLR9_A15BD_MASK | DDR_PHY_ACBDLR9_RESERVED_23_22_MASK | DDR_PHY_ACBDLR9_A14BD_MASK | DDR_PHY_ACBDLR9_RESERVED_15_14_MASK | DDR_PHY_ACBDLR9_A13BD_MASK | DDR_PHY_ACBDLR9_RESERVED_7_6_MASK | DDR_PHY_ACBDLR9_A12BD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ACBDLR9_RESERVED_31_30_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR9_A15BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR9_RESERVED_23_22_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR9_A14BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR9_RESERVED_15_14_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR9_A13BD_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR9_RESERVED_7_6_SHIFT - | 0x00000000U << DDR_PHY_ACBDLR9_A12BD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ACBDLR9_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : ZQCR @ 0XFD080680</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_ZQCR_RESERVED_31_26 0x0 - - ZQ VREF Range - PSU_DDR_PHY_ZQCR_ZQREFISELRANGE 0x0 - - Programmable Wait for Frequency B - PSU_DDR_PHY_ZQCR_PGWAIT_FRQB 0x11 - - Programmable Wait for Frequency A - PSU_DDR_PHY_ZQCR_PGWAIT_FRQA 0x11 - - ZQ VREF Pad Enable - PSU_DDR_PHY_ZQCR_ZQREFPEN 0x0 - - ZQ Internal VREF Enable - PSU_DDR_PHY_ZQCR_ZQREFIEN 0x1 - - Choice of termination mode - PSU_DDR_PHY_ZQCR_ODT_MODE 0x1 - - Force ZCAL VT update - PSU_DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE 0x0 - - IO VT Drift Limit - PSU_DDR_PHY_ZQCR_IODLMT 0x2 - - Averaging algorithm enable, if set, enables averaging algorithm - PSU_DDR_PHY_ZQCR_AVGEN 0x1 - - Maximum number of averaging rounds to be used by averaging algorithm - PSU_DDR_PHY_ZQCR_AVGMAX 0x2 - - ZQ Calibration Type - PSU_DDR_PHY_ZQCR_ZCALT 0x0 - - ZQ Power Down - PSU_DDR_PHY_ZQCR_ZQPD 0x0 - - ZQ Impedance Control Register - (OFFSET, MASK, VALUE) (0XFD080680, 0xFFFFFFFFU ,0x008A2A58U) - RegMask = (DDR_PHY_ZQCR_RESERVED_31_26_MASK | DDR_PHY_ZQCR_ZQREFISELRANGE_MASK | DDR_PHY_ZQCR_PGWAIT_FRQB_MASK | DDR_PHY_ZQCR_PGWAIT_FRQA_MASK | DDR_PHY_ZQCR_ZQREFPEN_MASK | DDR_PHY_ZQCR_ZQREFIEN_MASK | DDR_PHY_ZQCR_ODT_MODE_MASK | DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE_MASK | DDR_PHY_ZQCR_IODLMT_MASK | DDR_PHY_ZQCR_AVGEN_MASK | DDR_PHY_ZQCR_AVGMAX_MASK | DDR_PHY_ZQCR_ZCALT_MASK | DDR_PHY_ZQCR_ZQPD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ZQCR_RESERVED_31_26_SHIFT - | 0x00000000U << DDR_PHY_ZQCR_ZQREFISELRANGE_SHIFT - | 0x00000011U << DDR_PHY_ZQCR_PGWAIT_FRQB_SHIFT - | 0x00000011U << DDR_PHY_ZQCR_PGWAIT_FRQA_SHIFT - | 0x00000000U << DDR_PHY_ZQCR_ZQREFPEN_SHIFT - | 0x00000001U << DDR_PHY_ZQCR_ZQREFIEN_SHIFT - | 0x00000001U << DDR_PHY_ZQCR_ODT_MODE_SHIFT - | 0x00000000U << DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE_SHIFT - | 0x00000002U << DDR_PHY_ZQCR_IODLMT_SHIFT - | 0x00000001U << DDR_PHY_ZQCR_AVGEN_SHIFT - | 0x00000002U << DDR_PHY_ZQCR_AVGMAX_SHIFT - | 0x00000000U << DDR_PHY_ZQCR_ZCALT_SHIFT - | 0x00000000U << DDR_PHY_ZQCR_ZQPD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ZQCR_OFFSET ,0xFFFFFFFFU ,0x008A2A58U); - /*############################################################################################################################ */ - - /*Register : ZQ0PR0 @ 0XFD080684</p> - - Pull-down drive strength ZCTRL over-ride enable - PSU_DDR_PHY_ZQ0PR0_PD_DRV_ZDEN 0x0 - - Pull-up drive strength ZCTRL over-ride enable - PSU_DDR_PHY_ZQ0PR0_PU_DRV_ZDEN 0x0 - - Pull-down termination ZCTRL over-ride enable - PSU_DDR_PHY_ZQ0PR0_PD_ODT_ZDEN 0x0 - - Pull-up termination ZCTRL over-ride enable - PSU_DDR_PHY_ZQ0PR0_PU_ODT_ZDEN 0x0 - - Calibration segment bypass - PSU_DDR_PHY_ZQ0PR0_ZSEGBYP 0x0 - - VREF latch mode controls the mode in which the ZLE pin of the PVREF cell is driven by the PUB - PSU_DDR_PHY_ZQ0PR0_ZLE_MODE 0x0 - - Termination adjustment - PSU_DDR_PHY_ZQ0PR0_ODT_ADJUST 0x0 - - Pulldown drive strength adjustment - PSU_DDR_PHY_ZQ0PR0_PD_DRV_ADJUST 0x0 - - Pullup drive strength adjustment - PSU_DDR_PHY_ZQ0PR0_PU_DRV_ADJUST 0x0 - - DRAM Impedance Divide Ratio - PSU_DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT 0x7 - - HOST Impedance Divide Ratio - PSU_DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT 0x7 - - Impedance Divide Ratio (pulldown drive calibration during asymmetric drive strength calibration) - PSU_DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD 0xd - - Impedance Divide Ratio (pullup drive calibration during asymmetric drive strength calibration) - PSU_DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU 0xd - - ZQ n Impedance Control Program Register 0 - (OFFSET, MASK, VALUE) (0XFD080684, 0xFFFFFFFFU ,0x000077DDU) - RegMask = (DDR_PHY_ZQ0PR0_PD_DRV_ZDEN_MASK | DDR_PHY_ZQ0PR0_PU_DRV_ZDEN_MASK | DDR_PHY_ZQ0PR0_PD_ODT_ZDEN_MASK | DDR_PHY_ZQ0PR0_PU_ODT_ZDEN_MASK | DDR_PHY_ZQ0PR0_ZSEGBYP_MASK | DDR_PHY_ZQ0PR0_ZLE_MODE_MASK | DDR_PHY_ZQ0PR0_ODT_ADJUST_MASK | DDR_PHY_ZQ0PR0_PD_DRV_ADJUST_MASK | DDR_PHY_ZQ0PR0_PU_DRV_ADJUST_MASK | DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT_MASK | DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT_MASK | DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD_MASK | DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ZQ0PR0_PD_DRV_ZDEN_SHIFT - | 0x00000000U << DDR_PHY_ZQ0PR0_PU_DRV_ZDEN_SHIFT - | 0x00000000U << DDR_PHY_ZQ0PR0_PD_ODT_ZDEN_SHIFT - | 0x00000000U << DDR_PHY_ZQ0PR0_PU_ODT_ZDEN_SHIFT - | 0x00000000U << DDR_PHY_ZQ0PR0_ZSEGBYP_SHIFT - | 0x00000000U << DDR_PHY_ZQ0PR0_ZLE_MODE_SHIFT - | 0x00000000U << DDR_PHY_ZQ0PR0_ODT_ADJUST_SHIFT - | 0x00000000U << DDR_PHY_ZQ0PR0_PD_DRV_ADJUST_SHIFT - | 0x00000000U << DDR_PHY_ZQ0PR0_PU_DRV_ADJUST_SHIFT - | 0x00000007U << DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT_SHIFT - | 0x00000007U << DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT_SHIFT - | 0x0000000DU << DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD_SHIFT - | 0x0000000DU << DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ZQ0PR0_OFFSET ,0xFFFFFFFFU ,0x000077DDU); - /*############################################################################################################################ */ - - /*Register : ZQ0OR0 @ 0XFD080694</p> - - Reserved. Return zeros on reads. - PSU_DDR_PHY_ZQ0OR0_RESERVED_31_26 0x0 - - Override value for the pull-up output impedance - PSU_DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD 0x1e1 - - Reserved. Return zeros on reads. - PSU_DDR_PHY_ZQ0OR0_RESERVED_15_10 0x0 - - Override value for the pull-down output impedance - PSU_DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD 0x210 - - ZQ n Impedance Control Override Data Register 0 - (OFFSET, MASK, VALUE) (0XFD080694, 0xFFFFFFFFU ,0x01E10210U) - RegMask = (DDR_PHY_ZQ0OR0_RESERVED_31_26_MASK | DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD_MASK | DDR_PHY_ZQ0OR0_RESERVED_15_10_MASK | DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ZQ0OR0_RESERVED_31_26_SHIFT - | 0x000001E1U << DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD_SHIFT - | 0x00000000U << DDR_PHY_ZQ0OR0_RESERVED_15_10_SHIFT - | 0x00000210U << DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ZQ0OR0_OFFSET ,0xFFFFFFFFU ,0x01E10210U); - /*############################################################################################################################ */ - - /*Register : ZQ0OR1 @ 0XFD080698</p> - - Reserved. Return zeros on reads. - PSU_DDR_PHY_ZQ0OR1_RESERVED_31_26 0x0 - - Override value for the pull-up termination - PSU_DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD 0x1e1 - - Reserved. Return zeros on reads. - PSU_DDR_PHY_ZQ0OR1_RESERVED_15_10 0x0 - - Override value for the pull-down termination - PSU_DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD 0x0 - - ZQ n Impedance Control Override Data Register 1 - (OFFSET, MASK, VALUE) (0XFD080698, 0xFFFFFFFFU ,0x01E10000U) - RegMask = (DDR_PHY_ZQ0OR1_RESERVED_31_26_MASK | DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD_MASK | DDR_PHY_ZQ0OR1_RESERVED_15_10_MASK | DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ZQ0OR1_RESERVED_31_26_SHIFT - | 0x000001E1U << DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD_SHIFT - | 0x00000000U << DDR_PHY_ZQ0OR1_RESERVED_15_10_SHIFT - | 0x00000000U << DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ZQ0OR1_OFFSET ,0xFFFFFFFFU ,0x01E10000U); - /*############################################################################################################################ */ - - /*Register : ZQ1PR0 @ 0XFD0806A4</p> - - Pull-down drive strength ZCTRL over-ride enable - PSU_DDR_PHY_ZQ1PR0_PD_DRV_ZDEN 0x0 - - Pull-up drive strength ZCTRL over-ride enable - PSU_DDR_PHY_ZQ1PR0_PU_DRV_ZDEN 0x0 - - Pull-down termination ZCTRL over-ride enable - PSU_DDR_PHY_ZQ1PR0_PD_ODT_ZDEN 0x0 - - Pull-up termination ZCTRL over-ride enable - PSU_DDR_PHY_ZQ1PR0_PU_ODT_ZDEN 0x0 - - Calibration segment bypass - PSU_DDR_PHY_ZQ1PR0_ZSEGBYP 0x0 - - VREF latch mode controls the mode in which the ZLE pin of the PVREF cell is driven by the PUB - PSU_DDR_PHY_ZQ1PR0_ZLE_MODE 0x0 - - Termination adjustment - PSU_DDR_PHY_ZQ1PR0_ODT_ADJUST 0x0 - - Pulldown drive strength adjustment - PSU_DDR_PHY_ZQ1PR0_PD_DRV_ADJUST 0x1 - - Pullup drive strength adjustment - PSU_DDR_PHY_ZQ1PR0_PU_DRV_ADJUST 0x0 - - DRAM Impedance Divide Ratio - PSU_DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT 0x7 - - HOST Impedance Divide Ratio - PSU_DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT 0xb - - Impedance Divide Ratio (pulldown drive calibration during asymmetric drive strength calibration) - PSU_DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD 0xd - - Impedance Divide Ratio (pullup drive calibration during asymmetric drive strength calibration) - PSU_DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU 0xb - - ZQ n Impedance Control Program Register 0 - (OFFSET, MASK, VALUE) (0XFD0806A4, 0xFFFFFFFFU ,0x00087BDBU) - RegMask = (DDR_PHY_ZQ1PR0_PD_DRV_ZDEN_MASK | DDR_PHY_ZQ1PR0_PU_DRV_ZDEN_MASK | DDR_PHY_ZQ1PR0_PD_ODT_ZDEN_MASK | DDR_PHY_ZQ1PR0_PU_ODT_ZDEN_MASK | DDR_PHY_ZQ1PR0_ZSEGBYP_MASK | DDR_PHY_ZQ1PR0_ZLE_MODE_MASK | DDR_PHY_ZQ1PR0_ODT_ADJUST_MASK | DDR_PHY_ZQ1PR0_PD_DRV_ADJUST_MASK | DDR_PHY_ZQ1PR0_PU_DRV_ADJUST_MASK | DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT_MASK | DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT_MASK | DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD_MASK | DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_ZQ1PR0_PD_DRV_ZDEN_SHIFT - | 0x00000000U << DDR_PHY_ZQ1PR0_PU_DRV_ZDEN_SHIFT - | 0x00000000U << DDR_PHY_ZQ1PR0_PD_ODT_ZDEN_SHIFT - | 0x00000000U << DDR_PHY_ZQ1PR0_PU_ODT_ZDEN_SHIFT - | 0x00000000U << DDR_PHY_ZQ1PR0_ZSEGBYP_SHIFT - | 0x00000000U << DDR_PHY_ZQ1PR0_ZLE_MODE_SHIFT - | 0x00000000U << DDR_PHY_ZQ1PR0_ODT_ADJUST_SHIFT - | 0x00000001U << DDR_PHY_ZQ1PR0_PD_DRV_ADJUST_SHIFT - | 0x00000000U << DDR_PHY_ZQ1PR0_PU_DRV_ADJUST_SHIFT - | 0x00000007U << DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT_SHIFT - | 0x0000000BU << DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT_SHIFT - | 0x0000000DU << DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD_SHIFT - | 0x0000000BU << DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_ZQ1PR0_OFFSET ,0xFFFFFFFFU ,0x00087BDBU); - /*############################################################################################################################ */ - - /*Register : DX0GCR0 @ 0XFD080700</p> - - Calibration Bypass - PSU_DDR_PHY_DX0GCR0_CALBYP 0x0 - - Master Delay Line Enable - PSU_DDR_PHY_DX0GCR0_MDLEN 0x1 - - Configurable ODT(TE) Phase Shift - PSU_DDR_PHY_DX0GCR0_CODTSHFT 0x0 - - DQS Duty Cycle Correction - PSU_DDR_PHY_DX0GCR0_DQSDCC 0x0 - - Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY - PSU_DDR_PHY_DX0GCR0_RDDLY 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX0GCR0_RESERVED_19_14 0x0 - - DQSNSE Power Down Receiver - PSU_DDR_PHY_DX0GCR0_DQSNSEPDR 0x0 - - DQSSE Power Down Receiver - PSU_DDR_PHY_DX0GCR0_DQSSEPDR 0x0 - - RTT On Additive Latency - PSU_DDR_PHY_DX0GCR0_RTTOAL 0x0 - - RTT Output Hold - PSU_DDR_PHY_DX0GCR0_RTTOH 0x3 - - Configurable PDR Phase Shift - PSU_DDR_PHY_DX0GCR0_CPDRSHFT 0x0 - - DQSR Power Down - PSU_DDR_PHY_DX0GCR0_DQSRPD 0x0 - - DQSG Power Down Receiver - PSU_DDR_PHY_DX0GCR0_DQSGPDR 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX0GCR0_RESERVED_4 0x0 - - DQSG On-Die Termination - PSU_DDR_PHY_DX0GCR0_DQSGODT 0x0 - - DQSG Output Enable - PSU_DDR_PHY_DX0GCR0_DQSGOE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX0GCR0_RESERVED_1_0 0x0 - - DATX8 n General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080700, 0xFFFFFFFFU ,0x40800604U) - RegMask = (DDR_PHY_DX0GCR0_CALBYP_MASK | DDR_PHY_DX0GCR0_MDLEN_MASK | DDR_PHY_DX0GCR0_CODTSHFT_MASK | DDR_PHY_DX0GCR0_DQSDCC_MASK | DDR_PHY_DX0GCR0_RDDLY_MASK | DDR_PHY_DX0GCR0_RESERVED_19_14_MASK | DDR_PHY_DX0GCR0_DQSNSEPDR_MASK | DDR_PHY_DX0GCR0_DQSSEPDR_MASK | DDR_PHY_DX0GCR0_RTTOAL_MASK | DDR_PHY_DX0GCR0_RTTOH_MASK | DDR_PHY_DX0GCR0_CPDRSHFT_MASK | DDR_PHY_DX0GCR0_DQSRPD_MASK | DDR_PHY_DX0GCR0_DQSGPDR_MASK | DDR_PHY_DX0GCR0_RESERVED_4_MASK | DDR_PHY_DX0GCR0_DQSGODT_MASK | DDR_PHY_DX0GCR0_DQSGOE_MASK | DDR_PHY_DX0GCR0_RESERVED_1_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX0GCR0_CALBYP_SHIFT - | 0x00000001U << DDR_PHY_DX0GCR0_MDLEN_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_CODTSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_DQSDCC_SHIFT - | 0x00000008U << DDR_PHY_DX0GCR0_RDDLY_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_RESERVED_19_14_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_DQSNSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_DQSSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_RTTOAL_SHIFT - | 0x00000003U << DDR_PHY_DX0GCR0_RTTOH_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_CPDRSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_DQSRPD_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_DQSGPDR_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_RESERVED_4_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_DQSGODT_SHIFT - | 0x00000001U << DDR_PHY_DX0GCR0_DQSGOE_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR0_RESERVED_1_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX0GCR0_OFFSET ,0xFFFFFFFFU ,0x40800604U); - /*############################################################################################################################ */ - - /*Register : DX0GCR4 @ 0XFD080710</p> - - Byte lane VREF IOM (Used only by D4MU IOs) - PSU_DDR_PHY_DX0GCR4_RESERVED_31_29 0x0 - - Byte Lane VREF Pad Enable - PSU_DDR_PHY_DX0GCR4_DXREFPEN 0x0 - - Byte Lane Internal VREF Enable - PSU_DDR_PHY_DX0GCR4_DXREFEEN 0x3 - - Byte Lane Single-End VREF Enable - PSU_DDR_PHY_DX0GCR4_DXREFSEN 0x1 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX0GCR4_RESERVED_24 0x0 - - External VREF generator REFSEL range select - PSU_DDR_PHY_DX0GCR4_DXREFESELRANGE 0x0 - - Byte Lane External VREF Select - PSU_DDR_PHY_DX0GCR4_DXREFESEL 0x0 - - Single ended VREF generator REFSEL range select - PSU_DDR_PHY_DX0GCR4_DXREFSSELRANGE 0x1 - - Byte Lane Single-End VREF Select - PSU_DDR_PHY_DX0GCR4_DXREFSSEL 0x30 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX0GCR4_RESERVED_7_6 0x0 - - VREF Enable control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX0GCR4_DXREFIEN 0xf - - VRMON control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX0GCR4_DXREFIMON 0x0 - - DATX8 n General Configuration Register 4 - (OFFSET, MASK, VALUE) (0XFD080710, 0xFFFFFFFFU ,0x0E00B03CU) - RegMask = (DDR_PHY_DX0GCR4_RESERVED_31_29_MASK | DDR_PHY_DX0GCR4_DXREFPEN_MASK | DDR_PHY_DX0GCR4_DXREFEEN_MASK | DDR_PHY_DX0GCR4_DXREFSEN_MASK | DDR_PHY_DX0GCR4_RESERVED_24_MASK | DDR_PHY_DX0GCR4_DXREFESELRANGE_MASK | DDR_PHY_DX0GCR4_DXREFESEL_MASK | DDR_PHY_DX0GCR4_DXREFSSELRANGE_MASK | DDR_PHY_DX0GCR4_DXREFSSEL_MASK | DDR_PHY_DX0GCR4_RESERVED_7_6_MASK | DDR_PHY_DX0GCR4_DXREFIEN_MASK | DDR_PHY_DX0GCR4_DXREFIMON_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX0GCR4_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR4_DXREFPEN_SHIFT - | 0x00000003U << DDR_PHY_DX0GCR4_DXREFEEN_SHIFT - | 0x00000001U << DDR_PHY_DX0GCR4_DXREFSEN_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR4_RESERVED_24_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR4_DXREFESELRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR4_DXREFESEL_SHIFT - | 0x00000001U << DDR_PHY_DX0GCR4_DXREFSSELRANGE_SHIFT - | 0x00000030U << DDR_PHY_DX0GCR4_DXREFSSEL_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR4_RESERVED_7_6_SHIFT - | 0x0000000FU << DDR_PHY_DX0GCR4_DXREFIEN_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR4_DXREFIMON_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX0GCR4_OFFSET ,0xFFFFFFFFU ,0x0E00B03CU); - /*############################################################################################################################ */ - - /*Register : DX0GCR5 @ 0XFD080714</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX0GCR5_RESERVED_31 0x0 - - Byte Lane internal VREF Select for Rank 3 - PSU_DDR_PHY_DX0GCR5_DXREFISELR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX0GCR5_RESERVED_23 0x0 - - Byte Lane internal VREF Select for Rank 2 - PSU_DDR_PHY_DX0GCR5_DXREFISELR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX0GCR5_RESERVED_15 0x0 - - Byte Lane internal VREF Select for Rank 1 - PSU_DDR_PHY_DX0GCR5_DXREFISELR1 0x4f - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX0GCR5_RESERVED_7 0x0 - - Byte Lane internal VREF Select for Rank 0 - PSU_DDR_PHY_DX0GCR5_DXREFISELR0 0x4f - - DATX8 n General Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD080714, 0xFFFFFFFFU ,0x09094F4FU) - RegMask = (DDR_PHY_DX0GCR5_RESERVED_31_MASK | DDR_PHY_DX0GCR5_DXREFISELR3_MASK | DDR_PHY_DX0GCR5_RESERVED_23_MASK | DDR_PHY_DX0GCR5_DXREFISELR2_MASK | DDR_PHY_DX0GCR5_RESERVED_15_MASK | DDR_PHY_DX0GCR5_DXREFISELR1_MASK | DDR_PHY_DX0GCR5_RESERVED_7_MASK | DDR_PHY_DX0GCR5_DXREFISELR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX0GCR5_RESERVED_31_SHIFT - | 0x00000009U << DDR_PHY_DX0GCR5_DXREFISELR3_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR5_RESERVED_23_SHIFT - | 0x00000009U << DDR_PHY_DX0GCR5_DXREFISELR2_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR5_RESERVED_15_SHIFT - | 0x0000004FU << DDR_PHY_DX0GCR5_DXREFISELR1_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR5_RESERVED_7_SHIFT - | 0x0000004FU << DDR_PHY_DX0GCR5_DXREFISELR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX0GCR5_OFFSET ,0xFFFFFFFFU ,0x09094F4FU); - /*############################################################################################################################ */ - - /*Register : DX0GCR6 @ 0XFD080718</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX0GCR6_RESERVED_31_30 0x0 - - DRAM DQ VREF Select for Rank3 - PSU_DDR_PHY_DX0GCR6_DXDQVREFR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX0GCR6_RESERVED_23_22 0x0 - - DRAM DQ VREF Select for Rank2 - PSU_DDR_PHY_DX0GCR6_DXDQVREFR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX0GCR6_RESERVED_15_14 0x0 - - DRAM DQ VREF Select for Rank1 - PSU_DDR_PHY_DX0GCR6_DXDQVREFR1 0x2b - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX0GCR6_RESERVED_7_6 0x0 - - DRAM DQ VREF Select for Rank0 - PSU_DDR_PHY_DX0GCR6_DXDQVREFR0 0x2b - - DATX8 n General Configuration Register 6 - (OFFSET, MASK, VALUE) (0XFD080718, 0xFFFFFFFFU ,0x09092B2BU) - RegMask = (DDR_PHY_DX0GCR6_RESERVED_31_30_MASK | DDR_PHY_DX0GCR6_DXDQVREFR3_MASK | DDR_PHY_DX0GCR6_RESERVED_23_22_MASK | DDR_PHY_DX0GCR6_DXDQVREFR2_MASK | DDR_PHY_DX0GCR6_RESERVED_15_14_MASK | DDR_PHY_DX0GCR6_DXDQVREFR1_MASK | DDR_PHY_DX0GCR6_RESERVED_7_6_MASK | DDR_PHY_DX0GCR6_DXDQVREFR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX0GCR6_RESERVED_31_30_SHIFT - | 0x00000009U << DDR_PHY_DX0GCR6_DXDQVREFR3_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR6_RESERVED_23_22_SHIFT - | 0x00000009U << DDR_PHY_DX0GCR6_DXDQVREFR2_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR6_RESERVED_15_14_SHIFT - | 0x0000002BU << DDR_PHY_DX0GCR6_DXDQVREFR1_SHIFT - | 0x00000000U << DDR_PHY_DX0GCR6_RESERVED_7_6_SHIFT - | 0x0000002BU << DDR_PHY_DX0GCR6_DXDQVREFR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX0GCR6_OFFSET ,0xFFFFFFFFU ,0x09092B2BU); - /*############################################################################################################################ */ - - /*Register : DX0LCDLR2 @ 0XFD080788</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX0LCDLR2_RESERVED_31_25 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX0LCDLR2_RESERVED_24_16 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX0LCDLR2_RESERVED_15_9 0x0 - - Read DQS Gating Delay - PSU_DDR_PHY_DX0LCDLR2_DQSGD 0x0 - - DATX8 n Local Calibrated Delay Line Register 2 - (OFFSET, MASK, VALUE) (0XFD080788, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_DX0LCDLR2_RESERVED_31_25_MASK | DDR_PHY_DX0LCDLR2_RESERVED_24_16_MASK | DDR_PHY_DX0LCDLR2_RESERVED_15_9_MASK | DDR_PHY_DX0LCDLR2_DQSGD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX0LCDLR2_RESERVED_31_25_SHIFT - | 0x00000000U << DDR_PHY_DX0LCDLR2_RESERVED_24_16_SHIFT - | 0x00000000U << DDR_PHY_DX0LCDLR2_RESERVED_15_9_SHIFT - | 0x00000000U << DDR_PHY_DX0LCDLR2_DQSGD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX0LCDLR2_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DX0GTR0 @ 0XFD0807C0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX0GTR0_RESERVED_31_24 0x0 - - DQ Write Path Latency Pipeline - PSU_DDR_PHY_DX0GTR0_WDQSL 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX0GTR0_RESERVED_23_20 0x0 - - Write Leveling System Latency - PSU_DDR_PHY_DX0GTR0_WLSL 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX0GTR0_RESERVED_15_13 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX0GTR0_RESERVED_12_8 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX0GTR0_RESERVED_7_5 0x0 - - DQS Gating System Latency - PSU_DDR_PHY_DX0GTR0_DGSL 0x0 - - DATX8 n General Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD0807C0, 0xFFFFFFFFU ,0x00020000U) - RegMask = (DDR_PHY_DX0GTR0_RESERVED_31_24_MASK | DDR_PHY_DX0GTR0_WDQSL_MASK | DDR_PHY_DX0GTR0_RESERVED_23_20_MASK | DDR_PHY_DX0GTR0_WLSL_MASK | DDR_PHY_DX0GTR0_RESERVED_15_13_MASK | DDR_PHY_DX0GTR0_RESERVED_12_8_MASK | DDR_PHY_DX0GTR0_RESERVED_7_5_MASK | DDR_PHY_DX0GTR0_DGSL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX0GTR0_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX0GTR0_WDQSL_SHIFT - | 0x00000000U << DDR_PHY_DX0GTR0_RESERVED_23_20_SHIFT - | 0x00000002U << DDR_PHY_DX0GTR0_WLSL_SHIFT - | 0x00000000U << DDR_PHY_DX0GTR0_RESERVED_15_13_SHIFT - | 0x00000000U << DDR_PHY_DX0GTR0_RESERVED_12_8_SHIFT - | 0x00000000U << DDR_PHY_DX0GTR0_RESERVED_7_5_SHIFT - | 0x00000000U << DDR_PHY_DX0GTR0_DGSL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX0GTR0_OFFSET ,0xFFFFFFFFU ,0x00020000U); - /*############################################################################################################################ */ - - /*Register : DX1GCR0 @ 0XFD080800</p> - - Calibration Bypass - PSU_DDR_PHY_DX1GCR0_CALBYP 0x0 - - Master Delay Line Enable - PSU_DDR_PHY_DX1GCR0_MDLEN 0x1 - - Configurable ODT(TE) Phase Shift - PSU_DDR_PHY_DX1GCR0_CODTSHFT 0x0 - - DQS Duty Cycle Correction - PSU_DDR_PHY_DX1GCR0_DQSDCC 0x0 - - Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY - PSU_DDR_PHY_DX1GCR0_RDDLY 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX1GCR0_RESERVED_19_14 0x0 - - DQSNSE Power Down Receiver - PSU_DDR_PHY_DX1GCR0_DQSNSEPDR 0x0 - - DQSSE Power Down Receiver - PSU_DDR_PHY_DX1GCR0_DQSSEPDR 0x0 - - RTT On Additive Latency - PSU_DDR_PHY_DX1GCR0_RTTOAL 0x0 - - RTT Output Hold - PSU_DDR_PHY_DX1GCR0_RTTOH 0x3 - - Configurable PDR Phase Shift - PSU_DDR_PHY_DX1GCR0_CPDRSHFT 0x0 - - DQSR Power Down - PSU_DDR_PHY_DX1GCR0_DQSRPD 0x0 - - DQSG Power Down Receiver - PSU_DDR_PHY_DX1GCR0_DQSGPDR 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX1GCR0_RESERVED_4 0x0 - - DQSG On-Die Termination - PSU_DDR_PHY_DX1GCR0_DQSGODT 0x0 - - DQSG Output Enable - PSU_DDR_PHY_DX1GCR0_DQSGOE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX1GCR0_RESERVED_1_0 0x0 - - DATX8 n General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080800, 0xFFFFFFFFU ,0x40800604U) - RegMask = (DDR_PHY_DX1GCR0_CALBYP_MASK | DDR_PHY_DX1GCR0_MDLEN_MASK | DDR_PHY_DX1GCR0_CODTSHFT_MASK | DDR_PHY_DX1GCR0_DQSDCC_MASK | DDR_PHY_DX1GCR0_RDDLY_MASK | DDR_PHY_DX1GCR0_RESERVED_19_14_MASK | DDR_PHY_DX1GCR0_DQSNSEPDR_MASK | DDR_PHY_DX1GCR0_DQSSEPDR_MASK | DDR_PHY_DX1GCR0_RTTOAL_MASK | DDR_PHY_DX1GCR0_RTTOH_MASK | DDR_PHY_DX1GCR0_CPDRSHFT_MASK | DDR_PHY_DX1GCR0_DQSRPD_MASK | DDR_PHY_DX1GCR0_DQSGPDR_MASK | DDR_PHY_DX1GCR0_RESERVED_4_MASK | DDR_PHY_DX1GCR0_DQSGODT_MASK | DDR_PHY_DX1GCR0_DQSGOE_MASK | DDR_PHY_DX1GCR0_RESERVED_1_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX1GCR0_CALBYP_SHIFT - | 0x00000001U << DDR_PHY_DX1GCR0_MDLEN_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_CODTSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_DQSDCC_SHIFT - | 0x00000008U << DDR_PHY_DX1GCR0_RDDLY_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_RESERVED_19_14_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_DQSNSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_DQSSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_RTTOAL_SHIFT - | 0x00000003U << DDR_PHY_DX1GCR0_RTTOH_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_CPDRSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_DQSRPD_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_DQSGPDR_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_RESERVED_4_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_DQSGODT_SHIFT - | 0x00000001U << DDR_PHY_DX1GCR0_DQSGOE_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR0_RESERVED_1_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX1GCR0_OFFSET ,0xFFFFFFFFU ,0x40800604U); - /*############################################################################################################################ */ - - /*Register : DX1GCR4 @ 0XFD080810</p> - - Byte lane VREF IOM (Used only by D4MU IOs) - PSU_DDR_PHY_DX1GCR4_RESERVED_31_29 0x0 - - Byte Lane VREF Pad Enable - PSU_DDR_PHY_DX1GCR4_DXREFPEN 0x0 - - Byte Lane Internal VREF Enable - PSU_DDR_PHY_DX1GCR4_DXREFEEN 0x3 - - Byte Lane Single-End VREF Enable - PSU_DDR_PHY_DX1GCR4_DXREFSEN 0x1 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX1GCR4_RESERVED_24 0x0 - - External VREF generator REFSEL range select - PSU_DDR_PHY_DX1GCR4_DXREFESELRANGE 0x0 - - Byte Lane External VREF Select - PSU_DDR_PHY_DX1GCR4_DXREFESEL 0x0 - - Single ended VREF generator REFSEL range select - PSU_DDR_PHY_DX1GCR4_DXREFSSELRANGE 0x1 - - Byte Lane Single-End VREF Select - PSU_DDR_PHY_DX1GCR4_DXREFSSEL 0x30 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX1GCR4_RESERVED_7_6 0x0 - - VREF Enable control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX1GCR4_DXREFIEN 0xf - - VRMON control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX1GCR4_DXREFIMON 0x0 - - DATX8 n General Configuration Register 4 - (OFFSET, MASK, VALUE) (0XFD080810, 0xFFFFFFFFU ,0x0E00B03CU) - RegMask = (DDR_PHY_DX1GCR4_RESERVED_31_29_MASK | DDR_PHY_DX1GCR4_DXREFPEN_MASK | DDR_PHY_DX1GCR4_DXREFEEN_MASK | DDR_PHY_DX1GCR4_DXREFSEN_MASK | DDR_PHY_DX1GCR4_RESERVED_24_MASK | DDR_PHY_DX1GCR4_DXREFESELRANGE_MASK | DDR_PHY_DX1GCR4_DXREFESEL_MASK | DDR_PHY_DX1GCR4_DXREFSSELRANGE_MASK | DDR_PHY_DX1GCR4_DXREFSSEL_MASK | DDR_PHY_DX1GCR4_RESERVED_7_6_MASK | DDR_PHY_DX1GCR4_DXREFIEN_MASK | DDR_PHY_DX1GCR4_DXREFIMON_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX1GCR4_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR4_DXREFPEN_SHIFT - | 0x00000003U << DDR_PHY_DX1GCR4_DXREFEEN_SHIFT - | 0x00000001U << DDR_PHY_DX1GCR4_DXREFSEN_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR4_RESERVED_24_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR4_DXREFESELRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR4_DXREFESEL_SHIFT - | 0x00000001U << DDR_PHY_DX1GCR4_DXREFSSELRANGE_SHIFT - | 0x00000030U << DDR_PHY_DX1GCR4_DXREFSSEL_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR4_RESERVED_7_6_SHIFT - | 0x0000000FU << DDR_PHY_DX1GCR4_DXREFIEN_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR4_DXREFIMON_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX1GCR4_OFFSET ,0xFFFFFFFFU ,0x0E00B03CU); - /*############################################################################################################################ */ - - /*Register : DX1GCR5 @ 0XFD080814</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX1GCR5_RESERVED_31 0x0 - - Byte Lane internal VREF Select for Rank 3 - PSU_DDR_PHY_DX1GCR5_DXREFISELR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX1GCR5_RESERVED_23 0x0 - - Byte Lane internal VREF Select for Rank 2 - PSU_DDR_PHY_DX1GCR5_DXREFISELR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX1GCR5_RESERVED_15 0x0 - - Byte Lane internal VREF Select for Rank 1 - PSU_DDR_PHY_DX1GCR5_DXREFISELR1 0x4f - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX1GCR5_RESERVED_7 0x0 - - Byte Lane internal VREF Select for Rank 0 - PSU_DDR_PHY_DX1GCR5_DXREFISELR0 0x4f - - DATX8 n General Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD080814, 0xFFFFFFFFU ,0x09094F4FU) - RegMask = (DDR_PHY_DX1GCR5_RESERVED_31_MASK | DDR_PHY_DX1GCR5_DXREFISELR3_MASK | DDR_PHY_DX1GCR5_RESERVED_23_MASK | DDR_PHY_DX1GCR5_DXREFISELR2_MASK | DDR_PHY_DX1GCR5_RESERVED_15_MASK | DDR_PHY_DX1GCR5_DXREFISELR1_MASK | DDR_PHY_DX1GCR5_RESERVED_7_MASK | DDR_PHY_DX1GCR5_DXREFISELR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX1GCR5_RESERVED_31_SHIFT - | 0x00000009U << DDR_PHY_DX1GCR5_DXREFISELR3_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR5_RESERVED_23_SHIFT - | 0x00000009U << DDR_PHY_DX1GCR5_DXREFISELR2_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR5_RESERVED_15_SHIFT - | 0x0000004FU << DDR_PHY_DX1GCR5_DXREFISELR1_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR5_RESERVED_7_SHIFT - | 0x0000004FU << DDR_PHY_DX1GCR5_DXREFISELR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX1GCR5_OFFSET ,0xFFFFFFFFU ,0x09094F4FU); - /*############################################################################################################################ */ - - /*Register : DX1GCR6 @ 0XFD080818</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX1GCR6_RESERVED_31_30 0x0 - - DRAM DQ VREF Select for Rank3 - PSU_DDR_PHY_DX1GCR6_DXDQVREFR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX1GCR6_RESERVED_23_22 0x0 - - DRAM DQ VREF Select for Rank2 - PSU_DDR_PHY_DX1GCR6_DXDQVREFR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX1GCR6_RESERVED_15_14 0x0 - - DRAM DQ VREF Select for Rank1 - PSU_DDR_PHY_DX1GCR6_DXDQVREFR1 0x2b - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX1GCR6_RESERVED_7_6 0x0 - - DRAM DQ VREF Select for Rank0 - PSU_DDR_PHY_DX1GCR6_DXDQVREFR0 0x2b - - DATX8 n General Configuration Register 6 - (OFFSET, MASK, VALUE) (0XFD080818, 0xFFFFFFFFU ,0x09092B2BU) - RegMask = (DDR_PHY_DX1GCR6_RESERVED_31_30_MASK | DDR_PHY_DX1GCR6_DXDQVREFR3_MASK | DDR_PHY_DX1GCR6_RESERVED_23_22_MASK | DDR_PHY_DX1GCR6_DXDQVREFR2_MASK | DDR_PHY_DX1GCR6_RESERVED_15_14_MASK | DDR_PHY_DX1GCR6_DXDQVREFR1_MASK | DDR_PHY_DX1GCR6_RESERVED_7_6_MASK | DDR_PHY_DX1GCR6_DXDQVREFR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX1GCR6_RESERVED_31_30_SHIFT - | 0x00000009U << DDR_PHY_DX1GCR6_DXDQVREFR3_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR6_RESERVED_23_22_SHIFT - | 0x00000009U << DDR_PHY_DX1GCR6_DXDQVREFR2_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR6_RESERVED_15_14_SHIFT - | 0x0000002BU << DDR_PHY_DX1GCR6_DXDQVREFR1_SHIFT - | 0x00000000U << DDR_PHY_DX1GCR6_RESERVED_7_6_SHIFT - | 0x0000002BU << DDR_PHY_DX1GCR6_DXDQVREFR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX1GCR6_OFFSET ,0xFFFFFFFFU ,0x09092B2BU); - /*############################################################################################################################ */ - - /*Register : DX1LCDLR2 @ 0XFD080888</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX1LCDLR2_RESERVED_31_25 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX1LCDLR2_RESERVED_24_16 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX1LCDLR2_RESERVED_15_9 0x0 - - Read DQS Gating Delay - PSU_DDR_PHY_DX1LCDLR2_DQSGD 0x0 - - DATX8 n Local Calibrated Delay Line Register 2 - (OFFSET, MASK, VALUE) (0XFD080888, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_DX1LCDLR2_RESERVED_31_25_MASK | DDR_PHY_DX1LCDLR2_RESERVED_24_16_MASK | DDR_PHY_DX1LCDLR2_RESERVED_15_9_MASK | DDR_PHY_DX1LCDLR2_DQSGD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX1LCDLR2_RESERVED_31_25_SHIFT - | 0x00000000U << DDR_PHY_DX1LCDLR2_RESERVED_24_16_SHIFT - | 0x00000000U << DDR_PHY_DX1LCDLR2_RESERVED_15_9_SHIFT - | 0x00000000U << DDR_PHY_DX1LCDLR2_DQSGD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX1LCDLR2_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DX1GTR0 @ 0XFD0808C0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX1GTR0_RESERVED_31_24 0x0 - - DQ Write Path Latency Pipeline - PSU_DDR_PHY_DX1GTR0_WDQSL 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX1GTR0_RESERVED_23_20 0x0 - - Write Leveling System Latency - PSU_DDR_PHY_DX1GTR0_WLSL 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX1GTR0_RESERVED_15_13 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX1GTR0_RESERVED_12_8 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX1GTR0_RESERVED_7_5 0x0 - - DQS Gating System Latency - PSU_DDR_PHY_DX1GTR0_DGSL 0x0 - - DATX8 n General Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD0808C0, 0xFFFFFFFFU ,0x00020000U) - RegMask = (DDR_PHY_DX1GTR0_RESERVED_31_24_MASK | DDR_PHY_DX1GTR0_WDQSL_MASK | DDR_PHY_DX1GTR0_RESERVED_23_20_MASK | DDR_PHY_DX1GTR0_WLSL_MASK | DDR_PHY_DX1GTR0_RESERVED_15_13_MASK | DDR_PHY_DX1GTR0_RESERVED_12_8_MASK | DDR_PHY_DX1GTR0_RESERVED_7_5_MASK | DDR_PHY_DX1GTR0_DGSL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX1GTR0_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX1GTR0_WDQSL_SHIFT - | 0x00000000U << DDR_PHY_DX1GTR0_RESERVED_23_20_SHIFT - | 0x00000002U << DDR_PHY_DX1GTR0_WLSL_SHIFT - | 0x00000000U << DDR_PHY_DX1GTR0_RESERVED_15_13_SHIFT - | 0x00000000U << DDR_PHY_DX1GTR0_RESERVED_12_8_SHIFT - | 0x00000000U << DDR_PHY_DX1GTR0_RESERVED_7_5_SHIFT - | 0x00000000U << DDR_PHY_DX1GTR0_DGSL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX1GTR0_OFFSET ,0xFFFFFFFFU ,0x00020000U); - /*############################################################################################################################ */ - - /*Register : DX2GCR0 @ 0XFD080900</p> - - Calibration Bypass - PSU_DDR_PHY_DX2GCR0_CALBYP 0x0 - - Master Delay Line Enable - PSU_DDR_PHY_DX2GCR0_MDLEN 0x1 - - Configurable ODT(TE) Phase Shift - PSU_DDR_PHY_DX2GCR0_CODTSHFT 0x0 - - DQS Duty Cycle Correction - PSU_DDR_PHY_DX2GCR0_DQSDCC 0x0 - - Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY - PSU_DDR_PHY_DX2GCR0_RDDLY 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX2GCR0_RESERVED_19_14 0x0 - - DQSNSE Power Down Receiver - PSU_DDR_PHY_DX2GCR0_DQSNSEPDR 0x0 - - DQSSE Power Down Receiver - PSU_DDR_PHY_DX2GCR0_DQSSEPDR 0x0 - - RTT On Additive Latency - PSU_DDR_PHY_DX2GCR0_RTTOAL 0x0 - - RTT Output Hold - PSU_DDR_PHY_DX2GCR0_RTTOH 0x3 - - Configurable PDR Phase Shift - PSU_DDR_PHY_DX2GCR0_CPDRSHFT 0x0 - - DQSR Power Down - PSU_DDR_PHY_DX2GCR0_DQSRPD 0x0 - - DQSG Power Down Receiver - PSU_DDR_PHY_DX2GCR0_DQSGPDR 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX2GCR0_RESERVED_4 0x0 - - DQSG On-Die Termination - PSU_DDR_PHY_DX2GCR0_DQSGODT 0x0 - - DQSG Output Enable - PSU_DDR_PHY_DX2GCR0_DQSGOE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX2GCR0_RESERVED_1_0 0x0 - - DATX8 n General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080900, 0xFFFFFFFFU ,0x40800604U) - RegMask = (DDR_PHY_DX2GCR0_CALBYP_MASK | DDR_PHY_DX2GCR0_MDLEN_MASK | DDR_PHY_DX2GCR0_CODTSHFT_MASK | DDR_PHY_DX2GCR0_DQSDCC_MASK | DDR_PHY_DX2GCR0_RDDLY_MASK | DDR_PHY_DX2GCR0_RESERVED_19_14_MASK | DDR_PHY_DX2GCR0_DQSNSEPDR_MASK | DDR_PHY_DX2GCR0_DQSSEPDR_MASK | DDR_PHY_DX2GCR0_RTTOAL_MASK | DDR_PHY_DX2GCR0_RTTOH_MASK | DDR_PHY_DX2GCR0_CPDRSHFT_MASK | DDR_PHY_DX2GCR0_DQSRPD_MASK | DDR_PHY_DX2GCR0_DQSGPDR_MASK | DDR_PHY_DX2GCR0_RESERVED_4_MASK | DDR_PHY_DX2GCR0_DQSGODT_MASK | DDR_PHY_DX2GCR0_DQSGOE_MASK | DDR_PHY_DX2GCR0_RESERVED_1_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX2GCR0_CALBYP_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR0_MDLEN_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_CODTSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_DQSDCC_SHIFT - | 0x00000008U << DDR_PHY_DX2GCR0_RDDLY_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_RESERVED_19_14_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_DQSNSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_DQSSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_RTTOAL_SHIFT - | 0x00000003U << DDR_PHY_DX2GCR0_RTTOH_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_CPDRSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_DQSRPD_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_DQSGPDR_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_RESERVED_4_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_DQSGODT_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR0_DQSGOE_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR0_RESERVED_1_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX2GCR0_OFFSET ,0xFFFFFFFFU ,0x40800604U); - /*############################################################################################################################ */ - - /*Register : DX2GCR1 @ 0XFD080904</p> - - Enables the PDR mode for DQ[7:0] - PSU_DDR_PHY_DX2GCR1_DXPDRMODE 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_DX2GCR1_RESERVED_15 0x0 - - Select the delayed or non-delayed read data strobe # - PSU_DDR_PHY_DX2GCR1_QSNSEL 0x1 - - Select the delayed or non-delayed read data strobe - PSU_DDR_PHY_DX2GCR1_QSSEL 0x1 - - Enables Read Data Strobe in a byte lane - PSU_DDR_PHY_DX2GCR1_OEEN 0x1 - - Enables PDR in a byte lane - PSU_DDR_PHY_DX2GCR1_PDREN 0x1 - - Enables ODT/TE in a byte lane - PSU_DDR_PHY_DX2GCR1_TEEN 0x1 - - Enables Write Data strobe in a byte lane - PSU_DDR_PHY_DX2GCR1_DSEN 0x1 - - Enables DM pin in a byte lane - PSU_DDR_PHY_DX2GCR1_DMEN 0x1 - - Enables DQ corresponding to each bit in a byte - PSU_DDR_PHY_DX2GCR1_DQEN 0xff - - DATX8 n General Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD080904, 0xFFFFFFFFU ,0x00007FFFU) - RegMask = (DDR_PHY_DX2GCR1_DXPDRMODE_MASK | DDR_PHY_DX2GCR1_RESERVED_15_MASK | DDR_PHY_DX2GCR1_QSNSEL_MASK | DDR_PHY_DX2GCR1_QSSEL_MASK | DDR_PHY_DX2GCR1_OEEN_MASK | DDR_PHY_DX2GCR1_PDREN_MASK | DDR_PHY_DX2GCR1_TEEN_MASK | DDR_PHY_DX2GCR1_DSEN_MASK | DDR_PHY_DX2GCR1_DMEN_MASK | DDR_PHY_DX2GCR1_DQEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX2GCR1_DXPDRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR1_RESERVED_15_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR1_QSNSEL_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR1_QSSEL_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR1_OEEN_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR1_PDREN_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR1_TEEN_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR1_DSEN_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR1_DMEN_SHIFT - | 0x000000FFU << DDR_PHY_DX2GCR1_DQEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX2GCR1_OFFSET ,0xFFFFFFFFU ,0x00007FFFU); - /*############################################################################################################################ */ - - /*Register : DX2GCR4 @ 0XFD080910</p> - - Byte lane VREF IOM (Used only by D4MU IOs) - PSU_DDR_PHY_DX2GCR4_RESERVED_31_29 0x0 - - Byte Lane VREF Pad Enable - PSU_DDR_PHY_DX2GCR4_DXREFPEN 0x0 - - Byte Lane Internal VREF Enable - PSU_DDR_PHY_DX2GCR4_DXREFEEN 0x3 - - Byte Lane Single-End VREF Enable - PSU_DDR_PHY_DX2GCR4_DXREFSEN 0x1 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX2GCR4_RESERVED_24 0x0 - - External VREF generator REFSEL range select - PSU_DDR_PHY_DX2GCR4_DXREFESELRANGE 0x0 - - Byte Lane External VREF Select - PSU_DDR_PHY_DX2GCR4_DXREFESEL 0x0 - - Single ended VREF generator REFSEL range select - PSU_DDR_PHY_DX2GCR4_DXREFSSELRANGE 0x1 - - Byte Lane Single-End VREF Select - PSU_DDR_PHY_DX2GCR4_DXREFSSEL 0x30 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX2GCR4_RESERVED_7_6 0x0 - - VREF Enable control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX2GCR4_DXREFIEN 0xf - - VRMON control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX2GCR4_DXREFIMON 0x0 - - DATX8 n General Configuration Register 4 - (OFFSET, MASK, VALUE) (0XFD080910, 0xFFFFFFFFU ,0x0E00B03CU) - RegMask = (DDR_PHY_DX2GCR4_RESERVED_31_29_MASK | DDR_PHY_DX2GCR4_DXREFPEN_MASK | DDR_PHY_DX2GCR4_DXREFEEN_MASK | DDR_PHY_DX2GCR4_DXREFSEN_MASK | DDR_PHY_DX2GCR4_RESERVED_24_MASK | DDR_PHY_DX2GCR4_DXREFESELRANGE_MASK | DDR_PHY_DX2GCR4_DXREFESEL_MASK | DDR_PHY_DX2GCR4_DXREFSSELRANGE_MASK | DDR_PHY_DX2GCR4_DXREFSSEL_MASK | DDR_PHY_DX2GCR4_RESERVED_7_6_MASK | DDR_PHY_DX2GCR4_DXREFIEN_MASK | DDR_PHY_DX2GCR4_DXREFIMON_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX2GCR4_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR4_DXREFPEN_SHIFT - | 0x00000003U << DDR_PHY_DX2GCR4_DXREFEEN_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR4_DXREFSEN_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR4_RESERVED_24_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR4_DXREFESELRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR4_DXREFESEL_SHIFT - | 0x00000001U << DDR_PHY_DX2GCR4_DXREFSSELRANGE_SHIFT - | 0x00000030U << DDR_PHY_DX2GCR4_DXREFSSEL_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR4_RESERVED_7_6_SHIFT - | 0x0000000FU << DDR_PHY_DX2GCR4_DXREFIEN_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR4_DXREFIMON_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX2GCR4_OFFSET ,0xFFFFFFFFU ,0x0E00B03CU); - /*############################################################################################################################ */ - - /*Register : DX2GCR5 @ 0XFD080914</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX2GCR5_RESERVED_31 0x0 - - Byte Lane internal VREF Select for Rank 3 - PSU_DDR_PHY_DX2GCR5_DXREFISELR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX2GCR5_RESERVED_23 0x0 - - Byte Lane internal VREF Select for Rank 2 - PSU_DDR_PHY_DX2GCR5_DXREFISELR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX2GCR5_RESERVED_15 0x0 - - Byte Lane internal VREF Select for Rank 1 - PSU_DDR_PHY_DX2GCR5_DXREFISELR1 0x4f - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX2GCR5_RESERVED_7 0x0 - - Byte Lane internal VREF Select for Rank 0 - PSU_DDR_PHY_DX2GCR5_DXREFISELR0 0x4f - - DATX8 n General Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD080914, 0xFFFFFFFFU ,0x09094F4FU) - RegMask = (DDR_PHY_DX2GCR5_RESERVED_31_MASK | DDR_PHY_DX2GCR5_DXREFISELR3_MASK | DDR_PHY_DX2GCR5_RESERVED_23_MASK | DDR_PHY_DX2GCR5_DXREFISELR2_MASK | DDR_PHY_DX2GCR5_RESERVED_15_MASK | DDR_PHY_DX2GCR5_DXREFISELR1_MASK | DDR_PHY_DX2GCR5_RESERVED_7_MASK | DDR_PHY_DX2GCR5_DXREFISELR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX2GCR5_RESERVED_31_SHIFT - | 0x00000009U << DDR_PHY_DX2GCR5_DXREFISELR3_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR5_RESERVED_23_SHIFT - | 0x00000009U << DDR_PHY_DX2GCR5_DXREFISELR2_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR5_RESERVED_15_SHIFT - | 0x0000004FU << DDR_PHY_DX2GCR5_DXREFISELR1_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR5_RESERVED_7_SHIFT - | 0x0000004FU << DDR_PHY_DX2GCR5_DXREFISELR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX2GCR5_OFFSET ,0xFFFFFFFFU ,0x09094F4FU); - /*############################################################################################################################ */ - - /*Register : DX2GCR6 @ 0XFD080918</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX2GCR6_RESERVED_31_30 0x0 - - DRAM DQ VREF Select for Rank3 - PSU_DDR_PHY_DX2GCR6_DXDQVREFR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX2GCR6_RESERVED_23_22 0x0 - - DRAM DQ VREF Select for Rank2 - PSU_DDR_PHY_DX2GCR6_DXDQVREFR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX2GCR6_RESERVED_15_14 0x0 - - DRAM DQ VREF Select for Rank1 - PSU_DDR_PHY_DX2GCR6_DXDQVREFR1 0x2b - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX2GCR6_RESERVED_7_6 0x0 - - DRAM DQ VREF Select for Rank0 - PSU_DDR_PHY_DX2GCR6_DXDQVREFR0 0x2b - - DATX8 n General Configuration Register 6 - (OFFSET, MASK, VALUE) (0XFD080918, 0xFFFFFFFFU ,0x09092B2BU) - RegMask = (DDR_PHY_DX2GCR6_RESERVED_31_30_MASK | DDR_PHY_DX2GCR6_DXDQVREFR3_MASK | DDR_PHY_DX2GCR6_RESERVED_23_22_MASK | DDR_PHY_DX2GCR6_DXDQVREFR2_MASK | DDR_PHY_DX2GCR6_RESERVED_15_14_MASK | DDR_PHY_DX2GCR6_DXDQVREFR1_MASK | DDR_PHY_DX2GCR6_RESERVED_7_6_MASK | DDR_PHY_DX2GCR6_DXDQVREFR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX2GCR6_RESERVED_31_30_SHIFT - | 0x00000009U << DDR_PHY_DX2GCR6_DXDQVREFR3_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR6_RESERVED_23_22_SHIFT - | 0x00000009U << DDR_PHY_DX2GCR6_DXDQVREFR2_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR6_RESERVED_15_14_SHIFT - | 0x0000002BU << DDR_PHY_DX2GCR6_DXDQVREFR1_SHIFT - | 0x00000000U << DDR_PHY_DX2GCR6_RESERVED_7_6_SHIFT - | 0x0000002BU << DDR_PHY_DX2GCR6_DXDQVREFR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX2GCR6_OFFSET ,0xFFFFFFFFU ,0x09092B2BU); - /*############################################################################################################################ */ - - /*Register : DX2LCDLR2 @ 0XFD080988</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX2LCDLR2_RESERVED_31_25 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX2LCDLR2_RESERVED_24_16 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX2LCDLR2_RESERVED_15_9 0x0 - - Read DQS Gating Delay - PSU_DDR_PHY_DX2LCDLR2_DQSGD 0x0 - - DATX8 n Local Calibrated Delay Line Register 2 - (OFFSET, MASK, VALUE) (0XFD080988, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_DX2LCDLR2_RESERVED_31_25_MASK | DDR_PHY_DX2LCDLR2_RESERVED_24_16_MASK | DDR_PHY_DX2LCDLR2_RESERVED_15_9_MASK | DDR_PHY_DX2LCDLR2_DQSGD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX2LCDLR2_RESERVED_31_25_SHIFT - | 0x00000000U << DDR_PHY_DX2LCDLR2_RESERVED_24_16_SHIFT - | 0x00000000U << DDR_PHY_DX2LCDLR2_RESERVED_15_9_SHIFT - | 0x00000000U << DDR_PHY_DX2LCDLR2_DQSGD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX2LCDLR2_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DX2GTR0 @ 0XFD0809C0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX2GTR0_RESERVED_31_24 0x0 - - DQ Write Path Latency Pipeline - PSU_DDR_PHY_DX2GTR0_WDQSL 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX2GTR0_RESERVED_23_20 0x0 - - Write Leveling System Latency - PSU_DDR_PHY_DX2GTR0_WLSL 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX2GTR0_RESERVED_15_13 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX2GTR0_RESERVED_12_8 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX2GTR0_RESERVED_7_5 0x0 - - DQS Gating System Latency - PSU_DDR_PHY_DX2GTR0_DGSL 0x0 - - DATX8 n General Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD0809C0, 0xFFFFFFFFU ,0x00020000U) - RegMask = (DDR_PHY_DX2GTR0_RESERVED_31_24_MASK | DDR_PHY_DX2GTR0_WDQSL_MASK | DDR_PHY_DX2GTR0_RESERVED_23_20_MASK | DDR_PHY_DX2GTR0_WLSL_MASK | DDR_PHY_DX2GTR0_RESERVED_15_13_MASK | DDR_PHY_DX2GTR0_RESERVED_12_8_MASK | DDR_PHY_DX2GTR0_RESERVED_7_5_MASK | DDR_PHY_DX2GTR0_DGSL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX2GTR0_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX2GTR0_WDQSL_SHIFT - | 0x00000000U << DDR_PHY_DX2GTR0_RESERVED_23_20_SHIFT - | 0x00000002U << DDR_PHY_DX2GTR0_WLSL_SHIFT - | 0x00000000U << DDR_PHY_DX2GTR0_RESERVED_15_13_SHIFT - | 0x00000000U << DDR_PHY_DX2GTR0_RESERVED_12_8_SHIFT - | 0x00000000U << DDR_PHY_DX2GTR0_RESERVED_7_5_SHIFT - | 0x00000000U << DDR_PHY_DX2GTR0_DGSL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX2GTR0_OFFSET ,0xFFFFFFFFU ,0x00020000U); - /*############################################################################################################################ */ - - /*Register : DX3GCR0 @ 0XFD080A00</p> - - Calibration Bypass - PSU_DDR_PHY_DX3GCR0_CALBYP 0x0 - - Master Delay Line Enable - PSU_DDR_PHY_DX3GCR0_MDLEN 0x1 - - Configurable ODT(TE) Phase Shift - PSU_DDR_PHY_DX3GCR0_CODTSHFT 0x0 - - DQS Duty Cycle Correction - PSU_DDR_PHY_DX3GCR0_DQSDCC 0x0 - - Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY - PSU_DDR_PHY_DX3GCR0_RDDLY 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX3GCR0_RESERVED_19_14 0x0 - - DQSNSE Power Down Receiver - PSU_DDR_PHY_DX3GCR0_DQSNSEPDR 0x0 - - DQSSE Power Down Receiver - PSU_DDR_PHY_DX3GCR0_DQSSEPDR 0x0 - - RTT On Additive Latency - PSU_DDR_PHY_DX3GCR0_RTTOAL 0x0 - - RTT Output Hold - PSU_DDR_PHY_DX3GCR0_RTTOH 0x3 - - Configurable PDR Phase Shift - PSU_DDR_PHY_DX3GCR0_CPDRSHFT 0x0 - - DQSR Power Down - PSU_DDR_PHY_DX3GCR0_DQSRPD 0x0 - - DQSG Power Down Receiver - PSU_DDR_PHY_DX3GCR0_DQSGPDR 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX3GCR0_RESERVED_4 0x0 - - DQSG On-Die Termination - PSU_DDR_PHY_DX3GCR0_DQSGODT 0x0 - - DQSG Output Enable - PSU_DDR_PHY_DX3GCR0_DQSGOE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX3GCR0_RESERVED_1_0 0x0 - - DATX8 n General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080A00, 0xFFFFFFFFU ,0x40800604U) - RegMask = (DDR_PHY_DX3GCR0_CALBYP_MASK | DDR_PHY_DX3GCR0_MDLEN_MASK | DDR_PHY_DX3GCR0_CODTSHFT_MASK | DDR_PHY_DX3GCR0_DQSDCC_MASK | DDR_PHY_DX3GCR0_RDDLY_MASK | DDR_PHY_DX3GCR0_RESERVED_19_14_MASK | DDR_PHY_DX3GCR0_DQSNSEPDR_MASK | DDR_PHY_DX3GCR0_DQSSEPDR_MASK | DDR_PHY_DX3GCR0_RTTOAL_MASK | DDR_PHY_DX3GCR0_RTTOH_MASK | DDR_PHY_DX3GCR0_CPDRSHFT_MASK | DDR_PHY_DX3GCR0_DQSRPD_MASK | DDR_PHY_DX3GCR0_DQSGPDR_MASK | DDR_PHY_DX3GCR0_RESERVED_4_MASK | DDR_PHY_DX3GCR0_DQSGODT_MASK | DDR_PHY_DX3GCR0_DQSGOE_MASK | DDR_PHY_DX3GCR0_RESERVED_1_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX3GCR0_CALBYP_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR0_MDLEN_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_CODTSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_DQSDCC_SHIFT - | 0x00000008U << DDR_PHY_DX3GCR0_RDDLY_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_RESERVED_19_14_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_DQSNSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_DQSSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_RTTOAL_SHIFT - | 0x00000003U << DDR_PHY_DX3GCR0_RTTOH_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_CPDRSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_DQSRPD_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_DQSGPDR_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_RESERVED_4_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_DQSGODT_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR0_DQSGOE_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR0_RESERVED_1_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX3GCR0_OFFSET ,0xFFFFFFFFU ,0x40800604U); - /*############################################################################################################################ */ - - /*Register : DX3GCR1 @ 0XFD080A04</p> - - Enables the PDR mode for DQ[7:0] - PSU_DDR_PHY_DX3GCR1_DXPDRMODE 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_DX3GCR1_RESERVED_15 0x0 - - Select the delayed or non-delayed read data strobe # - PSU_DDR_PHY_DX3GCR1_QSNSEL 0x1 - - Select the delayed or non-delayed read data strobe - PSU_DDR_PHY_DX3GCR1_QSSEL 0x1 - - Enables Read Data Strobe in a byte lane - PSU_DDR_PHY_DX3GCR1_OEEN 0x1 - - Enables PDR in a byte lane - PSU_DDR_PHY_DX3GCR1_PDREN 0x1 - - Enables ODT/TE in a byte lane - PSU_DDR_PHY_DX3GCR1_TEEN 0x1 - - Enables Write Data strobe in a byte lane - PSU_DDR_PHY_DX3GCR1_DSEN 0x1 - - Enables DM pin in a byte lane - PSU_DDR_PHY_DX3GCR1_DMEN 0x1 - - Enables DQ corresponding to each bit in a byte - PSU_DDR_PHY_DX3GCR1_DQEN 0xff - - DATX8 n General Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD080A04, 0xFFFFFFFFU ,0x00007FFFU) - RegMask = (DDR_PHY_DX3GCR1_DXPDRMODE_MASK | DDR_PHY_DX3GCR1_RESERVED_15_MASK | DDR_PHY_DX3GCR1_QSNSEL_MASK | DDR_PHY_DX3GCR1_QSSEL_MASK | DDR_PHY_DX3GCR1_OEEN_MASK | DDR_PHY_DX3GCR1_PDREN_MASK | DDR_PHY_DX3GCR1_TEEN_MASK | DDR_PHY_DX3GCR1_DSEN_MASK | DDR_PHY_DX3GCR1_DMEN_MASK | DDR_PHY_DX3GCR1_DQEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX3GCR1_DXPDRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR1_RESERVED_15_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR1_QSNSEL_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR1_QSSEL_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR1_OEEN_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR1_PDREN_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR1_TEEN_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR1_DSEN_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR1_DMEN_SHIFT - | 0x000000FFU << DDR_PHY_DX3GCR1_DQEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX3GCR1_OFFSET ,0xFFFFFFFFU ,0x00007FFFU); - /*############################################################################################################################ */ - - /*Register : DX3GCR4 @ 0XFD080A10</p> - - Byte lane VREF IOM (Used only by D4MU IOs) - PSU_DDR_PHY_DX3GCR4_RESERVED_31_29 0x0 - - Byte Lane VREF Pad Enable - PSU_DDR_PHY_DX3GCR4_DXREFPEN 0x0 - - Byte Lane Internal VREF Enable - PSU_DDR_PHY_DX3GCR4_DXREFEEN 0x3 - - Byte Lane Single-End VREF Enable - PSU_DDR_PHY_DX3GCR4_DXREFSEN 0x1 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX3GCR4_RESERVED_24 0x0 - - External VREF generator REFSEL range select - PSU_DDR_PHY_DX3GCR4_DXREFESELRANGE 0x0 - - Byte Lane External VREF Select - PSU_DDR_PHY_DX3GCR4_DXREFESEL 0x0 - - Single ended VREF generator REFSEL range select - PSU_DDR_PHY_DX3GCR4_DXREFSSELRANGE 0x1 - - Byte Lane Single-End VREF Select - PSU_DDR_PHY_DX3GCR4_DXREFSSEL 0x30 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX3GCR4_RESERVED_7_6 0x0 - - VREF Enable control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX3GCR4_DXREFIEN 0xf - - VRMON control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX3GCR4_DXREFIMON 0x0 - - DATX8 n General Configuration Register 4 - (OFFSET, MASK, VALUE) (0XFD080A10, 0xFFFFFFFFU ,0x0E00B03CU) - RegMask = (DDR_PHY_DX3GCR4_RESERVED_31_29_MASK | DDR_PHY_DX3GCR4_DXREFPEN_MASK | DDR_PHY_DX3GCR4_DXREFEEN_MASK | DDR_PHY_DX3GCR4_DXREFSEN_MASK | DDR_PHY_DX3GCR4_RESERVED_24_MASK | DDR_PHY_DX3GCR4_DXREFESELRANGE_MASK | DDR_PHY_DX3GCR4_DXREFESEL_MASK | DDR_PHY_DX3GCR4_DXREFSSELRANGE_MASK | DDR_PHY_DX3GCR4_DXREFSSEL_MASK | DDR_PHY_DX3GCR4_RESERVED_7_6_MASK | DDR_PHY_DX3GCR4_DXREFIEN_MASK | DDR_PHY_DX3GCR4_DXREFIMON_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX3GCR4_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR4_DXREFPEN_SHIFT - | 0x00000003U << DDR_PHY_DX3GCR4_DXREFEEN_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR4_DXREFSEN_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR4_RESERVED_24_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR4_DXREFESELRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR4_DXREFESEL_SHIFT - | 0x00000001U << DDR_PHY_DX3GCR4_DXREFSSELRANGE_SHIFT - | 0x00000030U << DDR_PHY_DX3GCR4_DXREFSSEL_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR4_RESERVED_7_6_SHIFT - | 0x0000000FU << DDR_PHY_DX3GCR4_DXREFIEN_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR4_DXREFIMON_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX3GCR4_OFFSET ,0xFFFFFFFFU ,0x0E00B03CU); - /*############################################################################################################################ */ - - /*Register : DX3GCR5 @ 0XFD080A14</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX3GCR5_RESERVED_31 0x0 - - Byte Lane internal VREF Select for Rank 3 - PSU_DDR_PHY_DX3GCR5_DXREFISELR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX3GCR5_RESERVED_23 0x0 - - Byte Lane internal VREF Select for Rank 2 - PSU_DDR_PHY_DX3GCR5_DXREFISELR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX3GCR5_RESERVED_15 0x0 - - Byte Lane internal VREF Select for Rank 1 - PSU_DDR_PHY_DX3GCR5_DXREFISELR1 0x4f - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX3GCR5_RESERVED_7 0x0 - - Byte Lane internal VREF Select for Rank 0 - PSU_DDR_PHY_DX3GCR5_DXREFISELR0 0x4f - - DATX8 n General Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD080A14, 0xFFFFFFFFU ,0x09094F4FU) - RegMask = (DDR_PHY_DX3GCR5_RESERVED_31_MASK | DDR_PHY_DX3GCR5_DXREFISELR3_MASK | DDR_PHY_DX3GCR5_RESERVED_23_MASK | DDR_PHY_DX3GCR5_DXREFISELR2_MASK | DDR_PHY_DX3GCR5_RESERVED_15_MASK | DDR_PHY_DX3GCR5_DXREFISELR1_MASK | DDR_PHY_DX3GCR5_RESERVED_7_MASK | DDR_PHY_DX3GCR5_DXREFISELR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX3GCR5_RESERVED_31_SHIFT - | 0x00000009U << DDR_PHY_DX3GCR5_DXREFISELR3_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR5_RESERVED_23_SHIFT - | 0x00000009U << DDR_PHY_DX3GCR5_DXREFISELR2_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR5_RESERVED_15_SHIFT - | 0x0000004FU << DDR_PHY_DX3GCR5_DXREFISELR1_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR5_RESERVED_7_SHIFT - | 0x0000004FU << DDR_PHY_DX3GCR5_DXREFISELR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX3GCR5_OFFSET ,0xFFFFFFFFU ,0x09094F4FU); - /*############################################################################################################################ */ - - /*Register : DX3GCR6 @ 0XFD080A18</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX3GCR6_RESERVED_31_30 0x0 - - DRAM DQ VREF Select for Rank3 - PSU_DDR_PHY_DX3GCR6_DXDQVREFR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX3GCR6_RESERVED_23_22 0x0 - - DRAM DQ VREF Select for Rank2 - PSU_DDR_PHY_DX3GCR6_DXDQVREFR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX3GCR6_RESERVED_15_14 0x0 - - DRAM DQ VREF Select for Rank1 - PSU_DDR_PHY_DX3GCR6_DXDQVREFR1 0x2b - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX3GCR6_RESERVED_7_6 0x0 - - DRAM DQ VREF Select for Rank0 - PSU_DDR_PHY_DX3GCR6_DXDQVREFR0 0x2b - - DATX8 n General Configuration Register 6 - (OFFSET, MASK, VALUE) (0XFD080A18, 0xFFFFFFFFU ,0x09092B2BU) - RegMask = (DDR_PHY_DX3GCR6_RESERVED_31_30_MASK | DDR_PHY_DX3GCR6_DXDQVREFR3_MASK | DDR_PHY_DX3GCR6_RESERVED_23_22_MASK | DDR_PHY_DX3GCR6_DXDQVREFR2_MASK | DDR_PHY_DX3GCR6_RESERVED_15_14_MASK | DDR_PHY_DX3GCR6_DXDQVREFR1_MASK | DDR_PHY_DX3GCR6_RESERVED_7_6_MASK | DDR_PHY_DX3GCR6_DXDQVREFR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX3GCR6_RESERVED_31_30_SHIFT - | 0x00000009U << DDR_PHY_DX3GCR6_DXDQVREFR3_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR6_RESERVED_23_22_SHIFT - | 0x00000009U << DDR_PHY_DX3GCR6_DXDQVREFR2_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR6_RESERVED_15_14_SHIFT - | 0x0000002BU << DDR_PHY_DX3GCR6_DXDQVREFR1_SHIFT - | 0x00000000U << DDR_PHY_DX3GCR6_RESERVED_7_6_SHIFT - | 0x0000002BU << DDR_PHY_DX3GCR6_DXDQVREFR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX3GCR6_OFFSET ,0xFFFFFFFFU ,0x09092B2BU); - /*############################################################################################################################ */ - - /*Register : DX3LCDLR2 @ 0XFD080A88</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX3LCDLR2_RESERVED_31_25 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX3LCDLR2_RESERVED_24_16 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX3LCDLR2_RESERVED_15_9 0x0 - - Read DQS Gating Delay - PSU_DDR_PHY_DX3LCDLR2_DQSGD 0x0 - - DATX8 n Local Calibrated Delay Line Register 2 - (OFFSET, MASK, VALUE) (0XFD080A88, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_DX3LCDLR2_RESERVED_31_25_MASK | DDR_PHY_DX3LCDLR2_RESERVED_24_16_MASK | DDR_PHY_DX3LCDLR2_RESERVED_15_9_MASK | DDR_PHY_DX3LCDLR2_DQSGD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX3LCDLR2_RESERVED_31_25_SHIFT - | 0x00000000U << DDR_PHY_DX3LCDLR2_RESERVED_24_16_SHIFT - | 0x00000000U << DDR_PHY_DX3LCDLR2_RESERVED_15_9_SHIFT - | 0x00000000U << DDR_PHY_DX3LCDLR2_DQSGD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX3LCDLR2_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DX3GTR0 @ 0XFD080AC0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX3GTR0_RESERVED_31_24 0x0 - - DQ Write Path Latency Pipeline - PSU_DDR_PHY_DX3GTR0_WDQSL 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX3GTR0_RESERVED_23_20 0x0 - - Write Leveling System Latency - PSU_DDR_PHY_DX3GTR0_WLSL 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX3GTR0_RESERVED_15_13 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX3GTR0_RESERVED_12_8 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX3GTR0_RESERVED_7_5 0x0 - - DQS Gating System Latency - PSU_DDR_PHY_DX3GTR0_DGSL 0x0 - - DATX8 n General Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD080AC0, 0xFFFFFFFFU ,0x00020000U) - RegMask = (DDR_PHY_DX3GTR0_RESERVED_31_24_MASK | DDR_PHY_DX3GTR0_WDQSL_MASK | DDR_PHY_DX3GTR0_RESERVED_23_20_MASK | DDR_PHY_DX3GTR0_WLSL_MASK | DDR_PHY_DX3GTR0_RESERVED_15_13_MASK | DDR_PHY_DX3GTR0_RESERVED_12_8_MASK | DDR_PHY_DX3GTR0_RESERVED_7_5_MASK | DDR_PHY_DX3GTR0_DGSL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX3GTR0_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX3GTR0_WDQSL_SHIFT - | 0x00000000U << DDR_PHY_DX3GTR0_RESERVED_23_20_SHIFT - | 0x00000002U << DDR_PHY_DX3GTR0_WLSL_SHIFT - | 0x00000000U << DDR_PHY_DX3GTR0_RESERVED_15_13_SHIFT - | 0x00000000U << DDR_PHY_DX3GTR0_RESERVED_12_8_SHIFT - | 0x00000000U << DDR_PHY_DX3GTR0_RESERVED_7_5_SHIFT - | 0x00000000U << DDR_PHY_DX3GTR0_DGSL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX3GTR0_OFFSET ,0xFFFFFFFFU ,0x00020000U); - /*############################################################################################################################ */ - - /*Register : DX4GCR0 @ 0XFD080B00</p> - - Calibration Bypass - PSU_DDR_PHY_DX4GCR0_CALBYP 0x0 - - Master Delay Line Enable - PSU_DDR_PHY_DX4GCR0_MDLEN 0x1 - - Configurable ODT(TE) Phase Shift - PSU_DDR_PHY_DX4GCR0_CODTSHFT 0x0 - - DQS Duty Cycle Correction - PSU_DDR_PHY_DX4GCR0_DQSDCC 0x0 - - Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY - PSU_DDR_PHY_DX4GCR0_RDDLY 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX4GCR0_RESERVED_19_14 0x0 - - DQSNSE Power Down Receiver - PSU_DDR_PHY_DX4GCR0_DQSNSEPDR 0x0 - - DQSSE Power Down Receiver - PSU_DDR_PHY_DX4GCR0_DQSSEPDR 0x0 - - RTT On Additive Latency - PSU_DDR_PHY_DX4GCR0_RTTOAL 0x0 - - RTT Output Hold - PSU_DDR_PHY_DX4GCR0_RTTOH 0x3 - - Configurable PDR Phase Shift - PSU_DDR_PHY_DX4GCR0_CPDRSHFT 0x0 - - DQSR Power Down - PSU_DDR_PHY_DX4GCR0_DQSRPD 0x0 - - DQSG Power Down Receiver - PSU_DDR_PHY_DX4GCR0_DQSGPDR 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX4GCR0_RESERVED_4 0x0 - - DQSG On-Die Termination - PSU_DDR_PHY_DX4GCR0_DQSGODT 0x0 - - DQSG Output Enable - PSU_DDR_PHY_DX4GCR0_DQSGOE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX4GCR0_RESERVED_1_0 0x0 - - DATX8 n General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080B00, 0xFFFFFFFFU ,0x40800604U) - RegMask = (DDR_PHY_DX4GCR0_CALBYP_MASK | DDR_PHY_DX4GCR0_MDLEN_MASK | DDR_PHY_DX4GCR0_CODTSHFT_MASK | DDR_PHY_DX4GCR0_DQSDCC_MASK | DDR_PHY_DX4GCR0_RDDLY_MASK | DDR_PHY_DX4GCR0_RESERVED_19_14_MASK | DDR_PHY_DX4GCR0_DQSNSEPDR_MASK | DDR_PHY_DX4GCR0_DQSSEPDR_MASK | DDR_PHY_DX4GCR0_RTTOAL_MASK | DDR_PHY_DX4GCR0_RTTOH_MASK | DDR_PHY_DX4GCR0_CPDRSHFT_MASK | DDR_PHY_DX4GCR0_DQSRPD_MASK | DDR_PHY_DX4GCR0_DQSGPDR_MASK | DDR_PHY_DX4GCR0_RESERVED_4_MASK | DDR_PHY_DX4GCR0_DQSGODT_MASK | DDR_PHY_DX4GCR0_DQSGOE_MASK | DDR_PHY_DX4GCR0_RESERVED_1_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX4GCR0_CALBYP_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR0_MDLEN_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_CODTSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_DQSDCC_SHIFT - | 0x00000008U << DDR_PHY_DX4GCR0_RDDLY_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_RESERVED_19_14_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_DQSNSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_DQSSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_RTTOAL_SHIFT - | 0x00000003U << DDR_PHY_DX4GCR0_RTTOH_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_CPDRSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_DQSRPD_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_DQSGPDR_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_RESERVED_4_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_DQSGODT_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR0_DQSGOE_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR0_RESERVED_1_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX4GCR0_OFFSET ,0xFFFFFFFFU ,0x40800604U); - /*############################################################################################################################ */ - - /*Register : DX4GCR1 @ 0XFD080B04</p> - - Enables the PDR mode for DQ[7:0] - PSU_DDR_PHY_DX4GCR1_DXPDRMODE 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_DX4GCR1_RESERVED_15 0x0 - - Select the delayed or non-delayed read data strobe # - PSU_DDR_PHY_DX4GCR1_QSNSEL 0x1 - - Select the delayed or non-delayed read data strobe - PSU_DDR_PHY_DX4GCR1_QSSEL 0x1 - - Enables Read Data Strobe in a byte lane - PSU_DDR_PHY_DX4GCR1_OEEN 0x1 - - Enables PDR in a byte lane - PSU_DDR_PHY_DX4GCR1_PDREN 0x1 - - Enables ODT/TE in a byte lane - PSU_DDR_PHY_DX4GCR1_TEEN 0x1 - - Enables Write Data strobe in a byte lane - PSU_DDR_PHY_DX4GCR1_DSEN 0x1 - - Enables DM pin in a byte lane - PSU_DDR_PHY_DX4GCR1_DMEN 0x1 - - Enables DQ corresponding to each bit in a byte - PSU_DDR_PHY_DX4GCR1_DQEN 0xff - - DATX8 n General Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD080B04, 0xFFFFFFFFU ,0x00007FFFU) - RegMask = (DDR_PHY_DX4GCR1_DXPDRMODE_MASK | DDR_PHY_DX4GCR1_RESERVED_15_MASK | DDR_PHY_DX4GCR1_QSNSEL_MASK | DDR_PHY_DX4GCR1_QSSEL_MASK | DDR_PHY_DX4GCR1_OEEN_MASK | DDR_PHY_DX4GCR1_PDREN_MASK | DDR_PHY_DX4GCR1_TEEN_MASK | DDR_PHY_DX4GCR1_DSEN_MASK | DDR_PHY_DX4GCR1_DMEN_MASK | DDR_PHY_DX4GCR1_DQEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX4GCR1_DXPDRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR1_RESERVED_15_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR1_QSNSEL_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR1_QSSEL_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR1_OEEN_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR1_PDREN_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR1_TEEN_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR1_DSEN_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR1_DMEN_SHIFT - | 0x000000FFU << DDR_PHY_DX4GCR1_DQEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX4GCR1_OFFSET ,0xFFFFFFFFU ,0x00007FFFU); - /*############################################################################################################################ */ - - /*Register : DX4GCR4 @ 0XFD080B10</p> - - Byte lane VREF IOM (Used only by D4MU IOs) - PSU_DDR_PHY_DX4GCR4_RESERVED_31_29 0x0 - - Byte Lane VREF Pad Enable - PSU_DDR_PHY_DX4GCR4_DXREFPEN 0x0 - - Byte Lane Internal VREF Enable - PSU_DDR_PHY_DX4GCR4_DXREFEEN 0x3 - - Byte Lane Single-End VREF Enable - PSU_DDR_PHY_DX4GCR4_DXREFSEN 0x1 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX4GCR4_RESERVED_24 0x0 - - External VREF generator REFSEL range select - PSU_DDR_PHY_DX4GCR4_DXREFESELRANGE 0x0 - - Byte Lane External VREF Select - PSU_DDR_PHY_DX4GCR4_DXREFESEL 0x0 - - Single ended VREF generator REFSEL range select - PSU_DDR_PHY_DX4GCR4_DXREFSSELRANGE 0x1 - - Byte Lane Single-End VREF Select - PSU_DDR_PHY_DX4GCR4_DXREFSSEL 0x30 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX4GCR4_RESERVED_7_6 0x0 - - VREF Enable control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX4GCR4_DXREFIEN 0xf - - VRMON control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX4GCR4_DXREFIMON 0x0 - - DATX8 n General Configuration Register 4 - (OFFSET, MASK, VALUE) (0XFD080B10, 0xFFFFFFFFU ,0x0E00B03CU) - RegMask = (DDR_PHY_DX4GCR4_RESERVED_31_29_MASK | DDR_PHY_DX4GCR4_DXREFPEN_MASK | DDR_PHY_DX4GCR4_DXREFEEN_MASK | DDR_PHY_DX4GCR4_DXREFSEN_MASK | DDR_PHY_DX4GCR4_RESERVED_24_MASK | DDR_PHY_DX4GCR4_DXREFESELRANGE_MASK | DDR_PHY_DX4GCR4_DXREFESEL_MASK | DDR_PHY_DX4GCR4_DXREFSSELRANGE_MASK | DDR_PHY_DX4GCR4_DXREFSSEL_MASK | DDR_PHY_DX4GCR4_RESERVED_7_6_MASK | DDR_PHY_DX4GCR4_DXREFIEN_MASK | DDR_PHY_DX4GCR4_DXREFIMON_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX4GCR4_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR4_DXREFPEN_SHIFT - | 0x00000003U << DDR_PHY_DX4GCR4_DXREFEEN_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR4_DXREFSEN_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR4_RESERVED_24_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR4_DXREFESELRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR4_DXREFESEL_SHIFT - | 0x00000001U << DDR_PHY_DX4GCR4_DXREFSSELRANGE_SHIFT - | 0x00000030U << DDR_PHY_DX4GCR4_DXREFSSEL_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR4_RESERVED_7_6_SHIFT - | 0x0000000FU << DDR_PHY_DX4GCR4_DXREFIEN_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR4_DXREFIMON_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX4GCR4_OFFSET ,0xFFFFFFFFU ,0x0E00B03CU); - /*############################################################################################################################ */ - - /*Register : DX4GCR5 @ 0XFD080B14</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX4GCR5_RESERVED_31 0x0 - - Byte Lane internal VREF Select for Rank 3 - PSU_DDR_PHY_DX4GCR5_DXREFISELR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX4GCR5_RESERVED_23 0x0 - - Byte Lane internal VREF Select for Rank 2 - PSU_DDR_PHY_DX4GCR5_DXREFISELR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX4GCR5_RESERVED_15 0x0 - - Byte Lane internal VREF Select for Rank 1 - PSU_DDR_PHY_DX4GCR5_DXREFISELR1 0x4f - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX4GCR5_RESERVED_7 0x0 - - Byte Lane internal VREF Select for Rank 0 - PSU_DDR_PHY_DX4GCR5_DXREFISELR0 0x4f - - DATX8 n General Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD080B14, 0xFFFFFFFFU ,0x09094F4FU) - RegMask = (DDR_PHY_DX4GCR5_RESERVED_31_MASK | DDR_PHY_DX4GCR5_DXREFISELR3_MASK | DDR_PHY_DX4GCR5_RESERVED_23_MASK | DDR_PHY_DX4GCR5_DXREFISELR2_MASK | DDR_PHY_DX4GCR5_RESERVED_15_MASK | DDR_PHY_DX4GCR5_DXREFISELR1_MASK | DDR_PHY_DX4GCR5_RESERVED_7_MASK | DDR_PHY_DX4GCR5_DXREFISELR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX4GCR5_RESERVED_31_SHIFT - | 0x00000009U << DDR_PHY_DX4GCR5_DXREFISELR3_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR5_RESERVED_23_SHIFT - | 0x00000009U << DDR_PHY_DX4GCR5_DXREFISELR2_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR5_RESERVED_15_SHIFT - | 0x0000004FU << DDR_PHY_DX4GCR5_DXREFISELR1_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR5_RESERVED_7_SHIFT - | 0x0000004FU << DDR_PHY_DX4GCR5_DXREFISELR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX4GCR5_OFFSET ,0xFFFFFFFFU ,0x09094F4FU); - /*############################################################################################################################ */ - - /*Register : DX4GCR6 @ 0XFD080B18</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX4GCR6_RESERVED_31_30 0x0 - - DRAM DQ VREF Select for Rank3 - PSU_DDR_PHY_DX4GCR6_DXDQVREFR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX4GCR6_RESERVED_23_22 0x0 - - DRAM DQ VREF Select for Rank2 - PSU_DDR_PHY_DX4GCR6_DXDQVREFR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX4GCR6_RESERVED_15_14 0x0 - - DRAM DQ VREF Select for Rank1 - PSU_DDR_PHY_DX4GCR6_DXDQVREFR1 0x2b - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX4GCR6_RESERVED_7_6 0x0 - - DRAM DQ VREF Select for Rank0 - PSU_DDR_PHY_DX4GCR6_DXDQVREFR0 0x2b - - DATX8 n General Configuration Register 6 - (OFFSET, MASK, VALUE) (0XFD080B18, 0xFFFFFFFFU ,0x09092B2BU) - RegMask = (DDR_PHY_DX4GCR6_RESERVED_31_30_MASK | DDR_PHY_DX4GCR6_DXDQVREFR3_MASK | DDR_PHY_DX4GCR6_RESERVED_23_22_MASK | DDR_PHY_DX4GCR6_DXDQVREFR2_MASK | DDR_PHY_DX4GCR6_RESERVED_15_14_MASK | DDR_PHY_DX4GCR6_DXDQVREFR1_MASK | DDR_PHY_DX4GCR6_RESERVED_7_6_MASK | DDR_PHY_DX4GCR6_DXDQVREFR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX4GCR6_RESERVED_31_30_SHIFT - | 0x00000009U << DDR_PHY_DX4GCR6_DXDQVREFR3_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR6_RESERVED_23_22_SHIFT - | 0x00000009U << DDR_PHY_DX4GCR6_DXDQVREFR2_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR6_RESERVED_15_14_SHIFT - | 0x0000002BU << DDR_PHY_DX4GCR6_DXDQVREFR1_SHIFT - | 0x00000000U << DDR_PHY_DX4GCR6_RESERVED_7_6_SHIFT - | 0x0000002BU << DDR_PHY_DX4GCR6_DXDQVREFR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX4GCR6_OFFSET ,0xFFFFFFFFU ,0x09092B2BU); - /*############################################################################################################################ */ - - /*Register : DX4LCDLR2 @ 0XFD080B88</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX4LCDLR2_RESERVED_31_25 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX4LCDLR2_RESERVED_24_16 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX4LCDLR2_RESERVED_15_9 0x0 - - Read DQS Gating Delay - PSU_DDR_PHY_DX4LCDLR2_DQSGD 0x0 - - DATX8 n Local Calibrated Delay Line Register 2 - (OFFSET, MASK, VALUE) (0XFD080B88, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_DX4LCDLR2_RESERVED_31_25_MASK | DDR_PHY_DX4LCDLR2_RESERVED_24_16_MASK | DDR_PHY_DX4LCDLR2_RESERVED_15_9_MASK | DDR_PHY_DX4LCDLR2_DQSGD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX4LCDLR2_RESERVED_31_25_SHIFT - | 0x00000000U << DDR_PHY_DX4LCDLR2_RESERVED_24_16_SHIFT - | 0x00000000U << DDR_PHY_DX4LCDLR2_RESERVED_15_9_SHIFT - | 0x00000000U << DDR_PHY_DX4LCDLR2_DQSGD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX4LCDLR2_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DX4GTR0 @ 0XFD080BC0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX4GTR0_RESERVED_31_24 0x0 - - DQ Write Path Latency Pipeline - PSU_DDR_PHY_DX4GTR0_WDQSL 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX4GTR0_RESERVED_23_20 0x0 - - Write Leveling System Latency - PSU_DDR_PHY_DX4GTR0_WLSL 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX4GTR0_RESERVED_15_13 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX4GTR0_RESERVED_12_8 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX4GTR0_RESERVED_7_5 0x0 - - DQS Gating System Latency - PSU_DDR_PHY_DX4GTR0_DGSL 0x0 - - DATX8 n General Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD080BC0, 0xFFFFFFFFU ,0x00020000U) - RegMask = (DDR_PHY_DX4GTR0_RESERVED_31_24_MASK | DDR_PHY_DX4GTR0_WDQSL_MASK | DDR_PHY_DX4GTR0_RESERVED_23_20_MASK | DDR_PHY_DX4GTR0_WLSL_MASK | DDR_PHY_DX4GTR0_RESERVED_15_13_MASK | DDR_PHY_DX4GTR0_RESERVED_12_8_MASK | DDR_PHY_DX4GTR0_RESERVED_7_5_MASK | DDR_PHY_DX4GTR0_DGSL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX4GTR0_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX4GTR0_WDQSL_SHIFT - | 0x00000000U << DDR_PHY_DX4GTR0_RESERVED_23_20_SHIFT - | 0x00000002U << DDR_PHY_DX4GTR0_WLSL_SHIFT - | 0x00000000U << DDR_PHY_DX4GTR0_RESERVED_15_13_SHIFT - | 0x00000000U << DDR_PHY_DX4GTR0_RESERVED_12_8_SHIFT - | 0x00000000U << DDR_PHY_DX4GTR0_RESERVED_7_5_SHIFT - | 0x00000000U << DDR_PHY_DX4GTR0_DGSL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX4GTR0_OFFSET ,0xFFFFFFFFU ,0x00020000U); - /*############################################################################################################################ */ - - /*Register : DX5GCR0 @ 0XFD080C00</p> - - Calibration Bypass - PSU_DDR_PHY_DX5GCR0_CALBYP 0x0 - - Master Delay Line Enable - PSU_DDR_PHY_DX5GCR0_MDLEN 0x1 - - Configurable ODT(TE) Phase Shift - PSU_DDR_PHY_DX5GCR0_CODTSHFT 0x0 - - DQS Duty Cycle Correction - PSU_DDR_PHY_DX5GCR0_DQSDCC 0x0 - - Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY - PSU_DDR_PHY_DX5GCR0_RDDLY 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX5GCR0_RESERVED_19_14 0x0 - - DQSNSE Power Down Receiver - PSU_DDR_PHY_DX5GCR0_DQSNSEPDR 0x0 - - DQSSE Power Down Receiver - PSU_DDR_PHY_DX5GCR0_DQSSEPDR 0x0 - - RTT On Additive Latency - PSU_DDR_PHY_DX5GCR0_RTTOAL 0x0 - - RTT Output Hold - PSU_DDR_PHY_DX5GCR0_RTTOH 0x3 - - Configurable PDR Phase Shift - PSU_DDR_PHY_DX5GCR0_CPDRSHFT 0x0 - - DQSR Power Down - PSU_DDR_PHY_DX5GCR0_DQSRPD 0x0 - - DQSG Power Down Receiver - PSU_DDR_PHY_DX5GCR0_DQSGPDR 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX5GCR0_RESERVED_4 0x0 - - DQSG On-Die Termination - PSU_DDR_PHY_DX5GCR0_DQSGODT 0x0 - - DQSG Output Enable - PSU_DDR_PHY_DX5GCR0_DQSGOE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX5GCR0_RESERVED_1_0 0x0 - - DATX8 n General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080C00, 0xFFFFFFFFU ,0x40800604U) - RegMask = (DDR_PHY_DX5GCR0_CALBYP_MASK | DDR_PHY_DX5GCR0_MDLEN_MASK | DDR_PHY_DX5GCR0_CODTSHFT_MASK | DDR_PHY_DX5GCR0_DQSDCC_MASK | DDR_PHY_DX5GCR0_RDDLY_MASK | DDR_PHY_DX5GCR0_RESERVED_19_14_MASK | DDR_PHY_DX5GCR0_DQSNSEPDR_MASK | DDR_PHY_DX5GCR0_DQSSEPDR_MASK | DDR_PHY_DX5GCR0_RTTOAL_MASK | DDR_PHY_DX5GCR0_RTTOH_MASK | DDR_PHY_DX5GCR0_CPDRSHFT_MASK | DDR_PHY_DX5GCR0_DQSRPD_MASK | DDR_PHY_DX5GCR0_DQSGPDR_MASK | DDR_PHY_DX5GCR0_RESERVED_4_MASK | DDR_PHY_DX5GCR0_DQSGODT_MASK | DDR_PHY_DX5GCR0_DQSGOE_MASK | DDR_PHY_DX5GCR0_RESERVED_1_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX5GCR0_CALBYP_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR0_MDLEN_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_CODTSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_DQSDCC_SHIFT - | 0x00000008U << DDR_PHY_DX5GCR0_RDDLY_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_RESERVED_19_14_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_DQSNSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_DQSSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_RTTOAL_SHIFT - | 0x00000003U << DDR_PHY_DX5GCR0_RTTOH_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_CPDRSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_DQSRPD_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_DQSGPDR_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_RESERVED_4_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_DQSGODT_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR0_DQSGOE_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR0_RESERVED_1_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX5GCR0_OFFSET ,0xFFFFFFFFU ,0x40800604U); - /*############################################################################################################################ */ - - /*Register : DX5GCR1 @ 0XFD080C04</p> - - Enables the PDR mode for DQ[7:0] - PSU_DDR_PHY_DX5GCR1_DXPDRMODE 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_DX5GCR1_RESERVED_15 0x0 - - Select the delayed or non-delayed read data strobe # - PSU_DDR_PHY_DX5GCR1_QSNSEL 0x1 - - Select the delayed or non-delayed read data strobe - PSU_DDR_PHY_DX5GCR1_QSSEL 0x1 - - Enables Read Data Strobe in a byte lane - PSU_DDR_PHY_DX5GCR1_OEEN 0x1 - - Enables PDR in a byte lane - PSU_DDR_PHY_DX5GCR1_PDREN 0x1 - - Enables ODT/TE in a byte lane - PSU_DDR_PHY_DX5GCR1_TEEN 0x1 - - Enables Write Data strobe in a byte lane - PSU_DDR_PHY_DX5GCR1_DSEN 0x1 - - Enables DM pin in a byte lane - PSU_DDR_PHY_DX5GCR1_DMEN 0x1 - - Enables DQ corresponding to each bit in a byte - PSU_DDR_PHY_DX5GCR1_DQEN 0xff - - DATX8 n General Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD080C04, 0xFFFFFFFFU ,0x00007FFFU) - RegMask = (DDR_PHY_DX5GCR1_DXPDRMODE_MASK | DDR_PHY_DX5GCR1_RESERVED_15_MASK | DDR_PHY_DX5GCR1_QSNSEL_MASK | DDR_PHY_DX5GCR1_QSSEL_MASK | DDR_PHY_DX5GCR1_OEEN_MASK | DDR_PHY_DX5GCR1_PDREN_MASK | DDR_PHY_DX5GCR1_TEEN_MASK | DDR_PHY_DX5GCR1_DSEN_MASK | DDR_PHY_DX5GCR1_DMEN_MASK | DDR_PHY_DX5GCR1_DQEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX5GCR1_DXPDRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR1_RESERVED_15_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR1_QSNSEL_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR1_QSSEL_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR1_OEEN_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR1_PDREN_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR1_TEEN_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR1_DSEN_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR1_DMEN_SHIFT - | 0x000000FFU << DDR_PHY_DX5GCR1_DQEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX5GCR1_OFFSET ,0xFFFFFFFFU ,0x00007FFFU); - /*############################################################################################################################ */ - - /*Register : DX5GCR4 @ 0XFD080C10</p> - - Byte lane VREF IOM (Used only by D4MU IOs) - PSU_DDR_PHY_DX5GCR4_RESERVED_31_29 0x0 - - Byte Lane VREF Pad Enable - PSU_DDR_PHY_DX5GCR4_DXREFPEN 0x0 - - Byte Lane Internal VREF Enable - PSU_DDR_PHY_DX5GCR4_DXREFEEN 0x3 - - Byte Lane Single-End VREF Enable - PSU_DDR_PHY_DX5GCR4_DXREFSEN 0x1 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX5GCR4_RESERVED_24 0x0 - - External VREF generator REFSEL range select - PSU_DDR_PHY_DX5GCR4_DXREFESELRANGE 0x0 - - Byte Lane External VREF Select - PSU_DDR_PHY_DX5GCR4_DXREFESEL 0x0 - - Single ended VREF generator REFSEL range select - PSU_DDR_PHY_DX5GCR4_DXREFSSELRANGE 0x1 - - Byte Lane Single-End VREF Select - PSU_DDR_PHY_DX5GCR4_DXREFSSEL 0x30 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX5GCR4_RESERVED_7_6 0x0 - - VREF Enable control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX5GCR4_DXREFIEN 0xf - - VRMON control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX5GCR4_DXREFIMON 0x0 - - DATX8 n General Configuration Register 4 - (OFFSET, MASK, VALUE) (0XFD080C10, 0xFFFFFFFFU ,0x0E00B03CU) - RegMask = (DDR_PHY_DX5GCR4_RESERVED_31_29_MASK | DDR_PHY_DX5GCR4_DXREFPEN_MASK | DDR_PHY_DX5GCR4_DXREFEEN_MASK | DDR_PHY_DX5GCR4_DXREFSEN_MASK | DDR_PHY_DX5GCR4_RESERVED_24_MASK | DDR_PHY_DX5GCR4_DXREFESELRANGE_MASK | DDR_PHY_DX5GCR4_DXREFESEL_MASK | DDR_PHY_DX5GCR4_DXREFSSELRANGE_MASK | DDR_PHY_DX5GCR4_DXREFSSEL_MASK | DDR_PHY_DX5GCR4_RESERVED_7_6_MASK | DDR_PHY_DX5GCR4_DXREFIEN_MASK | DDR_PHY_DX5GCR4_DXREFIMON_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX5GCR4_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR4_DXREFPEN_SHIFT - | 0x00000003U << DDR_PHY_DX5GCR4_DXREFEEN_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR4_DXREFSEN_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR4_RESERVED_24_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR4_DXREFESELRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR4_DXREFESEL_SHIFT - | 0x00000001U << DDR_PHY_DX5GCR4_DXREFSSELRANGE_SHIFT - | 0x00000030U << DDR_PHY_DX5GCR4_DXREFSSEL_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR4_RESERVED_7_6_SHIFT - | 0x0000000FU << DDR_PHY_DX5GCR4_DXREFIEN_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR4_DXREFIMON_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX5GCR4_OFFSET ,0xFFFFFFFFU ,0x0E00B03CU); - /*############################################################################################################################ */ - - /*Register : DX5GCR5 @ 0XFD080C14</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX5GCR5_RESERVED_31 0x0 - - Byte Lane internal VREF Select for Rank 3 - PSU_DDR_PHY_DX5GCR5_DXREFISELR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX5GCR5_RESERVED_23 0x0 - - Byte Lane internal VREF Select for Rank 2 - PSU_DDR_PHY_DX5GCR5_DXREFISELR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX5GCR5_RESERVED_15 0x0 - - Byte Lane internal VREF Select for Rank 1 - PSU_DDR_PHY_DX5GCR5_DXREFISELR1 0x4f - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX5GCR5_RESERVED_7 0x0 - - Byte Lane internal VREF Select for Rank 0 - PSU_DDR_PHY_DX5GCR5_DXREFISELR0 0x4f - - DATX8 n General Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD080C14, 0xFFFFFFFFU ,0x09094F4FU) - RegMask = (DDR_PHY_DX5GCR5_RESERVED_31_MASK | DDR_PHY_DX5GCR5_DXREFISELR3_MASK | DDR_PHY_DX5GCR5_RESERVED_23_MASK | DDR_PHY_DX5GCR5_DXREFISELR2_MASK | DDR_PHY_DX5GCR5_RESERVED_15_MASK | DDR_PHY_DX5GCR5_DXREFISELR1_MASK | DDR_PHY_DX5GCR5_RESERVED_7_MASK | DDR_PHY_DX5GCR5_DXREFISELR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX5GCR5_RESERVED_31_SHIFT - | 0x00000009U << DDR_PHY_DX5GCR5_DXREFISELR3_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR5_RESERVED_23_SHIFT - | 0x00000009U << DDR_PHY_DX5GCR5_DXREFISELR2_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR5_RESERVED_15_SHIFT - | 0x0000004FU << DDR_PHY_DX5GCR5_DXREFISELR1_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR5_RESERVED_7_SHIFT - | 0x0000004FU << DDR_PHY_DX5GCR5_DXREFISELR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX5GCR5_OFFSET ,0xFFFFFFFFU ,0x09094F4FU); - /*############################################################################################################################ */ - - /*Register : DX5GCR6 @ 0XFD080C18</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX5GCR6_RESERVED_31_30 0x0 - - DRAM DQ VREF Select for Rank3 - PSU_DDR_PHY_DX5GCR6_DXDQVREFR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX5GCR6_RESERVED_23_22 0x0 - - DRAM DQ VREF Select for Rank2 - PSU_DDR_PHY_DX5GCR6_DXDQVREFR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX5GCR6_RESERVED_15_14 0x0 - - DRAM DQ VREF Select for Rank1 - PSU_DDR_PHY_DX5GCR6_DXDQVREFR1 0x2b - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX5GCR6_RESERVED_7_6 0x0 - - DRAM DQ VREF Select for Rank0 - PSU_DDR_PHY_DX5GCR6_DXDQVREFR0 0x2b - - DATX8 n General Configuration Register 6 - (OFFSET, MASK, VALUE) (0XFD080C18, 0xFFFFFFFFU ,0x09092B2BU) - RegMask = (DDR_PHY_DX5GCR6_RESERVED_31_30_MASK | DDR_PHY_DX5GCR6_DXDQVREFR3_MASK | DDR_PHY_DX5GCR6_RESERVED_23_22_MASK | DDR_PHY_DX5GCR6_DXDQVREFR2_MASK | DDR_PHY_DX5GCR6_RESERVED_15_14_MASK | DDR_PHY_DX5GCR6_DXDQVREFR1_MASK | DDR_PHY_DX5GCR6_RESERVED_7_6_MASK | DDR_PHY_DX5GCR6_DXDQVREFR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX5GCR6_RESERVED_31_30_SHIFT - | 0x00000009U << DDR_PHY_DX5GCR6_DXDQVREFR3_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR6_RESERVED_23_22_SHIFT - | 0x00000009U << DDR_PHY_DX5GCR6_DXDQVREFR2_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR6_RESERVED_15_14_SHIFT - | 0x0000002BU << DDR_PHY_DX5GCR6_DXDQVREFR1_SHIFT - | 0x00000000U << DDR_PHY_DX5GCR6_RESERVED_7_6_SHIFT - | 0x0000002BU << DDR_PHY_DX5GCR6_DXDQVREFR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX5GCR6_OFFSET ,0xFFFFFFFFU ,0x09092B2BU); - /*############################################################################################################################ */ - - /*Register : DX5LCDLR2 @ 0XFD080C88</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX5LCDLR2_RESERVED_31_25 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX5LCDLR2_RESERVED_24_16 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX5LCDLR2_RESERVED_15_9 0x0 - - Read DQS Gating Delay - PSU_DDR_PHY_DX5LCDLR2_DQSGD 0x0 - - DATX8 n Local Calibrated Delay Line Register 2 - (OFFSET, MASK, VALUE) (0XFD080C88, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_DX5LCDLR2_RESERVED_31_25_MASK | DDR_PHY_DX5LCDLR2_RESERVED_24_16_MASK | DDR_PHY_DX5LCDLR2_RESERVED_15_9_MASK | DDR_PHY_DX5LCDLR2_DQSGD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX5LCDLR2_RESERVED_31_25_SHIFT - | 0x00000000U << DDR_PHY_DX5LCDLR2_RESERVED_24_16_SHIFT - | 0x00000000U << DDR_PHY_DX5LCDLR2_RESERVED_15_9_SHIFT - | 0x00000000U << DDR_PHY_DX5LCDLR2_DQSGD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX5LCDLR2_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DX5GTR0 @ 0XFD080CC0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX5GTR0_RESERVED_31_24 0x0 - - DQ Write Path Latency Pipeline - PSU_DDR_PHY_DX5GTR0_WDQSL 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX5GTR0_RESERVED_23_20 0x0 - - Write Leveling System Latency - PSU_DDR_PHY_DX5GTR0_WLSL 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX5GTR0_RESERVED_15_13 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX5GTR0_RESERVED_12_8 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX5GTR0_RESERVED_7_5 0x0 - - DQS Gating System Latency - PSU_DDR_PHY_DX5GTR0_DGSL 0x0 - - DATX8 n General Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD080CC0, 0xFFFFFFFFU ,0x00020000U) - RegMask = (DDR_PHY_DX5GTR0_RESERVED_31_24_MASK | DDR_PHY_DX5GTR0_WDQSL_MASK | DDR_PHY_DX5GTR0_RESERVED_23_20_MASK | DDR_PHY_DX5GTR0_WLSL_MASK | DDR_PHY_DX5GTR0_RESERVED_15_13_MASK | DDR_PHY_DX5GTR0_RESERVED_12_8_MASK | DDR_PHY_DX5GTR0_RESERVED_7_5_MASK | DDR_PHY_DX5GTR0_DGSL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX5GTR0_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX5GTR0_WDQSL_SHIFT - | 0x00000000U << DDR_PHY_DX5GTR0_RESERVED_23_20_SHIFT - | 0x00000002U << DDR_PHY_DX5GTR0_WLSL_SHIFT - | 0x00000000U << DDR_PHY_DX5GTR0_RESERVED_15_13_SHIFT - | 0x00000000U << DDR_PHY_DX5GTR0_RESERVED_12_8_SHIFT - | 0x00000000U << DDR_PHY_DX5GTR0_RESERVED_7_5_SHIFT - | 0x00000000U << DDR_PHY_DX5GTR0_DGSL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX5GTR0_OFFSET ,0xFFFFFFFFU ,0x00020000U); - /*############################################################################################################################ */ - - /*Register : DX6GCR0 @ 0XFD080D00</p> - - Calibration Bypass - PSU_DDR_PHY_DX6GCR0_CALBYP 0x0 - - Master Delay Line Enable - PSU_DDR_PHY_DX6GCR0_MDLEN 0x1 - - Configurable ODT(TE) Phase Shift - PSU_DDR_PHY_DX6GCR0_CODTSHFT 0x0 - - DQS Duty Cycle Correction - PSU_DDR_PHY_DX6GCR0_DQSDCC 0x0 - - Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY - PSU_DDR_PHY_DX6GCR0_RDDLY 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX6GCR0_RESERVED_19_14 0x0 - - DQSNSE Power Down Receiver - PSU_DDR_PHY_DX6GCR0_DQSNSEPDR 0x0 - - DQSSE Power Down Receiver - PSU_DDR_PHY_DX6GCR0_DQSSEPDR 0x0 - - RTT On Additive Latency - PSU_DDR_PHY_DX6GCR0_RTTOAL 0x0 - - RTT Output Hold - PSU_DDR_PHY_DX6GCR0_RTTOH 0x3 - - Configurable PDR Phase Shift - PSU_DDR_PHY_DX6GCR0_CPDRSHFT 0x0 - - DQSR Power Down - PSU_DDR_PHY_DX6GCR0_DQSRPD 0x0 - - DQSG Power Down Receiver - PSU_DDR_PHY_DX6GCR0_DQSGPDR 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX6GCR0_RESERVED_4 0x0 - - DQSG On-Die Termination - PSU_DDR_PHY_DX6GCR0_DQSGODT 0x0 - - DQSG Output Enable - PSU_DDR_PHY_DX6GCR0_DQSGOE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX6GCR0_RESERVED_1_0 0x0 - - DATX8 n General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080D00, 0xFFFFFFFFU ,0x40800604U) - RegMask = (DDR_PHY_DX6GCR0_CALBYP_MASK | DDR_PHY_DX6GCR0_MDLEN_MASK | DDR_PHY_DX6GCR0_CODTSHFT_MASK | DDR_PHY_DX6GCR0_DQSDCC_MASK | DDR_PHY_DX6GCR0_RDDLY_MASK | DDR_PHY_DX6GCR0_RESERVED_19_14_MASK | DDR_PHY_DX6GCR0_DQSNSEPDR_MASK | DDR_PHY_DX6GCR0_DQSSEPDR_MASK | DDR_PHY_DX6GCR0_RTTOAL_MASK | DDR_PHY_DX6GCR0_RTTOH_MASK | DDR_PHY_DX6GCR0_CPDRSHFT_MASK | DDR_PHY_DX6GCR0_DQSRPD_MASK | DDR_PHY_DX6GCR0_DQSGPDR_MASK | DDR_PHY_DX6GCR0_RESERVED_4_MASK | DDR_PHY_DX6GCR0_DQSGODT_MASK | DDR_PHY_DX6GCR0_DQSGOE_MASK | DDR_PHY_DX6GCR0_RESERVED_1_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX6GCR0_CALBYP_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR0_MDLEN_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_CODTSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_DQSDCC_SHIFT - | 0x00000008U << DDR_PHY_DX6GCR0_RDDLY_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_RESERVED_19_14_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_DQSNSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_DQSSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_RTTOAL_SHIFT - | 0x00000003U << DDR_PHY_DX6GCR0_RTTOH_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_CPDRSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_DQSRPD_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_DQSGPDR_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_RESERVED_4_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_DQSGODT_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR0_DQSGOE_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR0_RESERVED_1_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX6GCR0_OFFSET ,0xFFFFFFFFU ,0x40800604U); - /*############################################################################################################################ */ - - /*Register : DX6GCR1 @ 0XFD080D04</p> - - Enables the PDR mode for DQ[7:0] - PSU_DDR_PHY_DX6GCR1_DXPDRMODE 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_DX6GCR1_RESERVED_15 0x0 - - Select the delayed or non-delayed read data strobe # - PSU_DDR_PHY_DX6GCR1_QSNSEL 0x1 - - Select the delayed or non-delayed read data strobe - PSU_DDR_PHY_DX6GCR1_QSSEL 0x1 - - Enables Read Data Strobe in a byte lane - PSU_DDR_PHY_DX6GCR1_OEEN 0x1 - - Enables PDR in a byte lane - PSU_DDR_PHY_DX6GCR1_PDREN 0x1 - - Enables ODT/TE in a byte lane - PSU_DDR_PHY_DX6GCR1_TEEN 0x1 - - Enables Write Data strobe in a byte lane - PSU_DDR_PHY_DX6GCR1_DSEN 0x1 - - Enables DM pin in a byte lane - PSU_DDR_PHY_DX6GCR1_DMEN 0x1 - - Enables DQ corresponding to each bit in a byte - PSU_DDR_PHY_DX6GCR1_DQEN 0xff - - DATX8 n General Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD080D04, 0xFFFFFFFFU ,0x00007FFFU) - RegMask = (DDR_PHY_DX6GCR1_DXPDRMODE_MASK | DDR_PHY_DX6GCR1_RESERVED_15_MASK | DDR_PHY_DX6GCR1_QSNSEL_MASK | DDR_PHY_DX6GCR1_QSSEL_MASK | DDR_PHY_DX6GCR1_OEEN_MASK | DDR_PHY_DX6GCR1_PDREN_MASK | DDR_PHY_DX6GCR1_TEEN_MASK | DDR_PHY_DX6GCR1_DSEN_MASK | DDR_PHY_DX6GCR1_DMEN_MASK | DDR_PHY_DX6GCR1_DQEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX6GCR1_DXPDRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR1_RESERVED_15_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR1_QSNSEL_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR1_QSSEL_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR1_OEEN_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR1_PDREN_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR1_TEEN_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR1_DSEN_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR1_DMEN_SHIFT - | 0x000000FFU << DDR_PHY_DX6GCR1_DQEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX6GCR1_OFFSET ,0xFFFFFFFFU ,0x00007FFFU); - /*############################################################################################################################ */ - - /*Register : DX6GCR4 @ 0XFD080D10</p> - - Byte lane VREF IOM (Used only by D4MU IOs) - PSU_DDR_PHY_DX6GCR4_RESERVED_31_29 0x0 - - Byte Lane VREF Pad Enable - PSU_DDR_PHY_DX6GCR4_DXREFPEN 0x0 - - Byte Lane Internal VREF Enable - PSU_DDR_PHY_DX6GCR4_DXREFEEN 0x3 - - Byte Lane Single-End VREF Enable - PSU_DDR_PHY_DX6GCR4_DXREFSEN 0x1 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX6GCR4_RESERVED_24 0x0 - - External VREF generator REFSEL range select - PSU_DDR_PHY_DX6GCR4_DXREFESELRANGE 0x0 - - Byte Lane External VREF Select - PSU_DDR_PHY_DX6GCR4_DXREFESEL 0x0 - - Single ended VREF generator REFSEL range select - PSU_DDR_PHY_DX6GCR4_DXREFSSELRANGE 0x1 - - Byte Lane Single-End VREF Select - PSU_DDR_PHY_DX6GCR4_DXREFSSEL 0x30 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX6GCR4_RESERVED_7_6 0x0 - - VREF Enable control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX6GCR4_DXREFIEN 0xf - - VRMON control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX6GCR4_DXREFIMON 0x0 - - DATX8 n General Configuration Register 4 - (OFFSET, MASK, VALUE) (0XFD080D10, 0xFFFFFFFFU ,0x0E00B03CU) - RegMask = (DDR_PHY_DX6GCR4_RESERVED_31_29_MASK | DDR_PHY_DX6GCR4_DXREFPEN_MASK | DDR_PHY_DX6GCR4_DXREFEEN_MASK | DDR_PHY_DX6GCR4_DXREFSEN_MASK | DDR_PHY_DX6GCR4_RESERVED_24_MASK | DDR_PHY_DX6GCR4_DXREFESELRANGE_MASK | DDR_PHY_DX6GCR4_DXREFESEL_MASK | DDR_PHY_DX6GCR4_DXREFSSELRANGE_MASK | DDR_PHY_DX6GCR4_DXREFSSEL_MASK | DDR_PHY_DX6GCR4_RESERVED_7_6_MASK | DDR_PHY_DX6GCR4_DXREFIEN_MASK | DDR_PHY_DX6GCR4_DXREFIMON_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX6GCR4_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR4_DXREFPEN_SHIFT - | 0x00000003U << DDR_PHY_DX6GCR4_DXREFEEN_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR4_DXREFSEN_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR4_RESERVED_24_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR4_DXREFESELRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR4_DXREFESEL_SHIFT - | 0x00000001U << DDR_PHY_DX6GCR4_DXREFSSELRANGE_SHIFT - | 0x00000030U << DDR_PHY_DX6GCR4_DXREFSSEL_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR4_RESERVED_7_6_SHIFT - | 0x0000000FU << DDR_PHY_DX6GCR4_DXREFIEN_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR4_DXREFIMON_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX6GCR4_OFFSET ,0xFFFFFFFFU ,0x0E00B03CU); - /*############################################################################################################################ */ - - /*Register : DX6GCR5 @ 0XFD080D14</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX6GCR5_RESERVED_31 0x0 - - Byte Lane internal VREF Select for Rank 3 - PSU_DDR_PHY_DX6GCR5_DXREFISELR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX6GCR5_RESERVED_23 0x0 - - Byte Lane internal VREF Select for Rank 2 - PSU_DDR_PHY_DX6GCR5_DXREFISELR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX6GCR5_RESERVED_15 0x0 - - Byte Lane internal VREF Select for Rank 1 - PSU_DDR_PHY_DX6GCR5_DXREFISELR1 0x4f - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX6GCR5_RESERVED_7 0x0 - - Byte Lane internal VREF Select for Rank 0 - PSU_DDR_PHY_DX6GCR5_DXREFISELR0 0x4f - - DATX8 n General Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD080D14, 0xFFFFFFFFU ,0x09094F4FU) - RegMask = (DDR_PHY_DX6GCR5_RESERVED_31_MASK | DDR_PHY_DX6GCR5_DXREFISELR3_MASK | DDR_PHY_DX6GCR5_RESERVED_23_MASK | DDR_PHY_DX6GCR5_DXREFISELR2_MASK | DDR_PHY_DX6GCR5_RESERVED_15_MASK | DDR_PHY_DX6GCR5_DXREFISELR1_MASK | DDR_PHY_DX6GCR5_RESERVED_7_MASK | DDR_PHY_DX6GCR5_DXREFISELR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX6GCR5_RESERVED_31_SHIFT - | 0x00000009U << DDR_PHY_DX6GCR5_DXREFISELR3_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR5_RESERVED_23_SHIFT - | 0x00000009U << DDR_PHY_DX6GCR5_DXREFISELR2_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR5_RESERVED_15_SHIFT - | 0x0000004FU << DDR_PHY_DX6GCR5_DXREFISELR1_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR5_RESERVED_7_SHIFT - | 0x0000004FU << DDR_PHY_DX6GCR5_DXREFISELR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX6GCR5_OFFSET ,0xFFFFFFFFU ,0x09094F4FU); - /*############################################################################################################################ */ - - /*Register : DX6GCR6 @ 0XFD080D18</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX6GCR6_RESERVED_31_30 0x0 - - DRAM DQ VREF Select for Rank3 - PSU_DDR_PHY_DX6GCR6_DXDQVREFR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX6GCR6_RESERVED_23_22 0x0 - - DRAM DQ VREF Select for Rank2 - PSU_DDR_PHY_DX6GCR6_DXDQVREFR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX6GCR6_RESERVED_15_14 0x0 - - DRAM DQ VREF Select for Rank1 - PSU_DDR_PHY_DX6GCR6_DXDQVREFR1 0x2b - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX6GCR6_RESERVED_7_6 0x0 - - DRAM DQ VREF Select for Rank0 - PSU_DDR_PHY_DX6GCR6_DXDQVREFR0 0x2b - - DATX8 n General Configuration Register 6 - (OFFSET, MASK, VALUE) (0XFD080D18, 0xFFFFFFFFU ,0x09092B2BU) - RegMask = (DDR_PHY_DX6GCR6_RESERVED_31_30_MASK | DDR_PHY_DX6GCR6_DXDQVREFR3_MASK | DDR_PHY_DX6GCR6_RESERVED_23_22_MASK | DDR_PHY_DX6GCR6_DXDQVREFR2_MASK | DDR_PHY_DX6GCR6_RESERVED_15_14_MASK | DDR_PHY_DX6GCR6_DXDQVREFR1_MASK | DDR_PHY_DX6GCR6_RESERVED_7_6_MASK | DDR_PHY_DX6GCR6_DXDQVREFR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX6GCR6_RESERVED_31_30_SHIFT - | 0x00000009U << DDR_PHY_DX6GCR6_DXDQVREFR3_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR6_RESERVED_23_22_SHIFT - | 0x00000009U << DDR_PHY_DX6GCR6_DXDQVREFR2_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR6_RESERVED_15_14_SHIFT - | 0x0000002BU << DDR_PHY_DX6GCR6_DXDQVREFR1_SHIFT - | 0x00000000U << DDR_PHY_DX6GCR6_RESERVED_7_6_SHIFT - | 0x0000002BU << DDR_PHY_DX6GCR6_DXDQVREFR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX6GCR6_OFFSET ,0xFFFFFFFFU ,0x09092B2BU); - /*############################################################################################################################ */ - - /*Register : DX6LCDLR2 @ 0XFD080D88</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX6LCDLR2_RESERVED_31_25 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX6LCDLR2_RESERVED_24_16 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX6LCDLR2_RESERVED_15_9 0x0 - - Read DQS Gating Delay - PSU_DDR_PHY_DX6LCDLR2_DQSGD 0x0 - - DATX8 n Local Calibrated Delay Line Register 2 - (OFFSET, MASK, VALUE) (0XFD080D88, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_DX6LCDLR2_RESERVED_31_25_MASK | DDR_PHY_DX6LCDLR2_RESERVED_24_16_MASK | DDR_PHY_DX6LCDLR2_RESERVED_15_9_MASK | DDR_PHY_DX6LCDLR2_DQSGD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX6LCDLR2_RESERVED_31_25_SHIFT - | 0x00000000U << DDR_PHY_DX6LCDLR2_RESERVED_24_16_SHIFT - | 0x00000000U << DDR_PHY_DX6LCDLR2_RESERVED_15_9_SHIFT - | 0x00000000U << DDR_PHY_DX6LCDLR2_DQSGD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX6LCDLR2_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DX6GTR0 @ 0XFD080DC0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX6GTR0_RESERVED_31_24 0x0 - - DQ Write Path Latency Pipeline - PSU_DDR_PHY_DX6GTR0_WDQSL 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX6GTR0_RESERVED_23_20 0x0 - - Write Leveling System Latency - PSU_DDR_PHY_DX6GTR0_WLSL 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX6GTR0_RESERVED_15_13 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX6GTR0_RESERVED_12_8 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX6GTR0_RESERVED_7_5 0x0 - - DQS Gating System Latency - PSU_DDR_PHY_DX6GTR0_DGSL 0x0 - - DATX8 n General Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD080DC0, 0xFFFFFFFFU ,0x00020000U) - RegMask = (DDR_PHY_DX6GTR0_RESERVED_31_24_MASK | DDR_PHY_DX6GTR0_WDQSL_MASK | DDR_PHY_DX6GTR0_RESERVED_23_20_MASK | DDR_PHY_DX6GTR0_WLSL_MASK | DDR_PHY_DX6GTR0_RESERVED_15_13_MASK | DDR_PHY_DX6GTR0_RESERVED_12_8_MASK | DDR_PHY_DX6GTR0_RESERVED_7_5_MASK | DDR_PHY_DX6GTR0_DGSL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX6GTR0_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX6GTR0_WDQSL_SHIFT - | 0x00000000U << DDR_PHY_DX6GTR0_RESERVED_23_20_SHIFT - | 0x00000002U << DDR_PHY_DX6GTR0_WLSL_SHIFT - | 0x00000000U << DDR_PHY_DX6GTR0_RESERVED_15_13_SHIFT - | 0x00000000U << DDR_PHY_DX6GTR0_RESERVED_12_8_SHIFT - | 0x00000000U << DDR_PHY_DX6GTR0_RESERVED_7_5_SHIFT - | 0x00000000U << DDR_PHY_DX6GTR0_DGSL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX6GTR0_OFFSET ,0xFFFFFFFFU ,0x00020000U); - /*############################################################################################################################ */ - - /*Register : DX7GCR0 @ 0XFD080E00</p> - - Calibration Bypass - PSU_DDR_PHY_DX7GCR0_CALBYP 0x0 - - Master Delay Line Enable - PSU_DDR_PHY_DX7GCR0_MDLEN 0x1 - - Configurable ODT(TE) Phase Shift - PSU_DDR_PHY_DX7GCR0_CODTSHFT 0x0 - - DQS Duty Cycle Correction - PSU_DDR_PHY_DX7GCR0_DQSDCC 0x0 - - Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY - PSU_DDR_PHY_DX7GCR0_RDDLY 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX7GCR0_RESERVED_19_14 0x0 - - DQSNSE Power Down Receiver - PSU_DDR_PHY_DX7GCR0_DQSNSEPDR 0x0 - - DQSSE Power Down Receiver - PSU_DDR_PHY_DX7GCR0_DQSSEPDR 0x0 - - RTT On Additive Latency - PSU_DDR_PHY_DX7GCR0_RTTOAL 0x0 - - RTT Output Hold - PSU_DDR_PHY_DX7GCR0_RTTOH 0x3 - - Configurable PDR Phase Shift - PSU_DDR_PHY_DX7GCR0_CPDRSHFT 0x0 - - DQSR Power Down - PSU_DDR_PHY_DX7GCR0_DQSRPD 0x0 - - DQSG Power Down Receiver - PSU_DDR_PHY_DX7GCR0_DQSGPDR 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX7GCR0_RESERVED_4 0x0 - - DQSG On-Die Termination - PSU_DDR_PHY_DX7GCR0_DQSGODT 0x0 - - DQSG Output Enable - PSU_DDR_PHY_DX7GCR0_DQSGOE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX7GCR0_RESERVED_1_0 0x0 - - DATX8 n General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080E00, 0xFFFFFFFFU ,0x40800604U) - RegMask = (DDR_PHY_DX7GCR0_CALBYP_MASK | DDR_PHY_DX7GCR0_MDLEN_MASK | DDR_PHY_DX7GCR0_CODTSHFT_MASK | DDR_PHY_DX7GCR0_DQSDCC_MASK | DDR_PHY_DX7GCR0_RDDLY_MASK | DDR_PHY_DX7GCR0_RESERVED_19_14_MASK | DDR_PHY_DX7GCR0_DQSNSEPDR_MASK | DDR_PHY_DX7GCR0_DQSSEPDR_MASK | DDR_PHY_DX7GCR0_RTTOAL_MASK | DDR_PHY_DX7GCR0_RTTOH_MASK | DDR_PHY_DX7GCR0_CPDRSHFT_MASK | DDR_PHY_DX7GCR0_DQSRPD_MASK | DDR_PHY_DX7GCR0_DQSGPDR_MASK | DDR_PHY_DX7GCR0_RESERVED_4_MASK | DDR_PHY_DX7GCR0_DQSGODT_MASK | DDR_PHY_DX7GCR0_DQSGOE_MASK | DDR_PHY_DX7GCR0_RESERVED_1_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX7GCR0_CALBYP_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR0_MDLEN_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_CODTSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_DQSDCC_SHIFT - | 0x00000008U << DDR_PHY_DX7GCR0_RDDLY_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_RESERVED_19_14_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_DQSNSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_DQSSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_RTTOAL_SHIFT - | 0x00000003U << DDR_PHY_DX7GCR0_RTTOH_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_CPDRSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_DQSRPD_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_DQSGPDR_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_RESERVED_4_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_DQSGODT_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR0_DQSGOE_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR0_RESERVED_1_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX7GCR0_OFFSET ,0xFFFFFFFFU ,0x40800604U); - /*############################################################################################################################ */ - - /*Register : DX7GCR1 @ 0XFD080E04</p> - - Enables the PDR mode for DQ[7:0] - PSU_DDR_PHY_DX7GCR1_DXPDRMODE 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_DX7GCR1_RESERVED_15 0x0 - - Select the delayed or non-delayed read data strobe # - PSU_DDR_PHY_DX7GCR1_QSNSEL 0x1 - - Select the delayed or non-delayed read data strobe - PSU_DDR_PHY_DX7GCR1_QSSEL 0x1 - - Enables Read Data Strobe in a byte lane - PSU_DDR_PHY_DX7GCR1_OEEN 0x1 - - Enables PDR in a byte lane - PSU_DDR_PHY_DX7GCR1_PDREN 0x1 - - Enables ODT/TE in a byte lane - PSU_DDR_PHY_DX7GCR1_TEEN 0x1 - - Enables Write Data strobe in a byte lane - PSU_DDR_PHY_DX7GCR1_DSEN 0x1 - - Enables DM pin in a byte lane - PSU_DDR_PHY_DX7GCR1_DMEN 0x1 - - Enables DQ corresponding to each bit in a byte - PSU_DDR_PHY_DX7GCR1_DQEN 0xff - - DATX8 n General Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD080E04, 0xFFFFFFFFU ,0x00007FFFU) - RegMask = (DDR_PHY_DX7GCR1_DXPDRMODE_MASK | DDR_PHY_DX7GCR1_RESERVED_15_MASK | DDR_PHY_DX7GCR1_QSNSEL_MASK | DDR_PHY_DX7GCR1_QSSEL_MASK | DDR_PHY_DX7GCR1_OEEN_MASK | DDR_PHY_DX7GCR1_PDREN_MASK | DDR_PHY_DX7GCR1_TEEN_MASK | DDR_PHY_DX7GCR1_DSEN_MASK | DDR_PHY_DX7GCR1_DMEN_MASK | DDR_PHY_DX7GCR1_DQEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX7GCR1_DXPDRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR1_RESERVED_15_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR1_QSNSEL_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR1_QSSEL_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR1_OEEN_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR1_PDREN_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR1_TEEN_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR1_DSEN_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR1_DMEN_SHIFT - | 0x000000FFU << DDR_PHY_DX7GCR1_DQEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX7GCR1_OFFSET ,0xFFFFFFFFU ,0x00007FFFU); - /*############################################################################################################################ */ - - /*Register : DX7GCR4 @ 0XFD080E10</p> - - Byte lane VREF IOM (Used only by D4MU IOs) - PSU_DDR_PHY_DX7GCR4_RESERVED_31_29 0x0 - - Byte Lane VREF Pad Enable - PSU_DDR_PHY_DX7GCR4_DXREFPEN 0x0 - - Byte Lane Internal VREF Enable - PSU_DDR_PHY_DX7GCR4_DXREFEEN 0x3 - - Byte Lane Single-End VREF Enable - PSU_DDR_PHY_DX7GCR4_DXREFSEN 0x1 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX7GCR4_RESERVED_24 0x0 - - External VREF generator REFSEL range select - PSU_DDR_PHY_DX7GCR4_DXREFESELRANGE 0x0 - - Byte Lane External VREF Select - PSU_DDR_PHY_DX7GCR4_DXREFESEL 0x0 - - Single ended VREF generator REFSEL range select - PSU_DDR_PHY_DX7GCR4_DXREFSSELRANGE 0x1 - - Byte Lane Single-End VREF Select - PSU_DDR_PHY_DX7GCR4_DXREFSSEL 0x30 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX7GCR4_RESERVED_7_6 0x0 - - VREF Enable control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX7GCR4_DXREFIEN 0xf - - VRMON control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX7GCR4_DXREFIMON 0x0 - - DATX8 n General Configuration Register 4 - (OFFSET, MASK, VALUE) (0XFD080E10, 0xFFFFFFFFU ,0x0E00B03CU) - RegMask = (DDR_PHY_DX7GCR4_RESERVED_31_29_MASK | DDR_PHY_DX7GCR4_DXREFPEN_MASK | DDR_PHY_DX7GCR4_DXREFEEN_MASK | DDR_PHY_DX7GCR4_DXREFSEN_MASK | DDR_PHY_DX7GCR4_RESERVED_24_MASK | DDR_PHY_DX7GCR4_DXREFESELRANGE_MASK | DDR_PHY_DX7GCR4_DXREFESEL_MASK | DDR_PHY_DX7GCR4_DXREFSSELRANGE_MASK | DDR_PHY_DX7GCR4_DXREFSSEL_MASK | DDR_PHY_DX7GCR4_RESERVED_7_6_MASK | DDR_PHY_DX7GCR4_DXREFIEN_MASK | DDR_PHY_DX7GCR4_DXREFIMON_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX7GCR4_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR4_DXREFPEN_SHIFT - | 0x00000003U << DDR_PHY_DX7GCR4_DXREFEEN_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR4_DXREFSEN_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR4_RESERVED_24_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR4_DXREFESELRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR4_DXREFESEL_SHIFT - | 0x00000001U << DDR_PHY_DX7GCR4_DXREFSSELRANGE_SHIFT - | 0x00000030U << DDR_PHY_DX7GCR4_DXREFSSEL_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR4_RESERVED_7_6_SHIFT - | 0x0000000FU << DDR_PHY_DX7GCR4_DXREFIEN_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR4_DXREFIMON_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX7GCR4_OFFSET ,0xFFFFFFFFU ,0x0E00B03CU); - /*############################################################################################################################ */ - - /*Register : DX7GCR5 @ 0XFD080E14</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX7GCR5_RESERVED_31 0x0 - - Byte Lane internal VREF Select for Rank 3 - PSU_DDR_PHY_DX7GCR5_DXREFISELR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX7GCR5_RESERVED_23 0x0 - - Byte Lane internal VREF Select for Rank 2 - PSU_DDR_PHY_DX7GCR5_DXREFISELR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX7GCR5_RESERVED_15 0x0 - - Byte Lane internal VREF Select for Rank 1 - PSU_DDR_PHY_DX7GCR5_DXREFISELR1 0x4f - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX7GCR5_RESERVED_7 0x0 - - Byte Lane internal VREF Select for Rank 0 - PSU_DDR_PHY_DX7GCR5_DXREFISELR0 0x4f - - DATX8 n General Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD080E14, 0xFFFFFFFFU ,0x09094F4FU) - RegMask = (DDR_PHY_DX7GCR5_RESERVED_31_MASK | DDR_PHY_DX7GCR5_DXREFISELR3_MASK | DDR_PHY_DX7GCR5_RESERVED_23_MASK | DDR_PHY_DX7GCR5_DXREFISELR2_MASK | DDR_PHY_DX7GCR5_RESERVED_15_MASK | DDR_PHY_DX7GCR5_DXREFISELR1_MASK | DDR_PHY_DX7GCR5_RESERVED_7_MASK | DDR_PHY_DX7GCR5_DXREFISELR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX7GCR5_RESERVED_31_SHIFT - | 0x00000009U << DDR_PHY_DX7GCR5_DXREFISELR3_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR5_RESERVED_23_SHIFT - | 0x00000009U << DDR_PHY_DX7GCR5_DXREFISELR2_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR5_RESERVED_15_SHIFT - | 0x0000004FU << DDR_PHY_DX7GCR5_DXREFISELR1_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR5_RESERVED_7_SHIFT - | 0x0000004FU << DDR_PHY_DX7GCR5_DXREFISELR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX7GCR5_OFFSET ,0xFFFFFFFFU ,0x09094F4FU); - /*############################################################################################################################ */ - - /*Register : DX7GCR6 @ 0XFD080E18</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX7GCR6_RESERVED_31_30 0x0 - - DRAM DQ VREF Select for Rank3 - PSU_DDR_PHY_DX7GCR6_DXDQVREFR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX7GCR6_RESERVED_23_22 0x0 - - DRAM DQ VREF Select for Rank2 - PSU_DDR_PHY_DX7GCR6_DXDQVREFR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX7GCR6_RESERVED_15_14 0x0 - - DRAM DQ VREF Select for Rank1 - PSU_DDR_PHY_DX7GCR6_DXDQVREFR1 0x2b - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX7GCR6_RESERVED_7_6 0x0 - - DRAM DQ VREF Select for Rank0 - PSU_DDR_PHY_DX7GCR6_DXDQVREFR0 0x2b - - DATX8 n General Configuration Register 6 - (OFFSET, MASK, VALUE) (0XFD080E18, 0xFFFFFFFFU ,0x09092B2BU) - RegMask = (DDR_PHY_DX7GCR6_RESERVED_31_30_MASK | DDR_PHY_DX7GCR6_DXDQVREFR3_MASK | DDR_PHY_DX7GCR6_RESERVED_23_22_MASK | DDR_PHY_DX7GCR6_DXDQVREFR2_MASK | DDR_PHY_DX7GCR6_RESERVED_15_14_MASK | DDR_PHY_DX7GCR6_DXDQVREFR1_MASK | DDR_PHY_DX7GCR6_RESERVED_7_6_MASK | DDR_PHY_DX7GCR6_DXDQVREFR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX7GCR6_RESERVED_31_30_SHIFT - | 0x00000009U << DDR_PHY_DX7GCR6_DXDQVREFR3_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR6_RESERVED_23_22_SHIFT - | 0x00000009U << DDR_PHY_DX7GCR6_DXDQVREFR2_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR6_RESERVED_15_14_SHIFT - | 0x0000002BU << DDR_PHY_DX7GCR6_DXDQVREFR1_SHIFT - | 0x00000000U << DDR_PHY_DX7GCR6_RESERVED_7_6_SHIFT - | 0x0000002BU << DDR_PHY_DX7GCR6_DXDQVREFR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX7GCR6_OFFSET ,0xFFFFFFFFU ,0x09092B2BU); - /*############################################################################################################################ */ - - /*Register : DX7LCDLR2 @ 0XFD080E88</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX7LCDLR2_RESERVED_31_25 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX7LCDLR2_RESERVED_24_16 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX7LCDLR2_RESERVED_15_9 0x0 - - Read DQS Gating Delay - PSU_DDR_PHY_DX7LCDLR2_DQSGD 0xa - - DATX8 n Local Calibrated Delay Line Register 2 - (OFFSET, MASK, VALUE) (0XFD080E88, 0xFFFFFFFFU ,0x0000000AU) - RegMask = (DDR_PHY_DX7LCDLR2_RESERVED_31_25_MASK | DDR_PHY_DX7LCDLR2_RESERVED_24_16_MASK | DDR_PHY_DX7LCDLR2_RESERVED_15_9_MASK | DDR_PHY_DX7LCDLR2_DQSGD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX7LCDLR2_RESERVED_31_25_SHIFT - | 0x00000000U << DDR_PHY_DX7LCDLR2_RESERVED_24_16_SHIFT - | 0x00000000U << DDR_PHY_DX7LCDLR2_RESERVED_15_9_SHIFT - | 0x0000000AU << DDR_PHY_DX7LCDLR2_DQSGD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX7LCDLR2_OFFSET ,0xFFFFFFFFU ,0x0000000AU); - /*############################################################################################################################ */ - - /*Register : DX7GTR0 @ 0XFD080EC0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX7GTR0_RESERVED_31_24 0x0 - - DQ Write Path Latency Pipeline - PSU_DDR_PHY_DX7GTR0_WDQSL 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX7GTR0_RESERVED_23_20 0x0 - - Write Leveling System Latency - PSU_DDR_PHY_DX7GTR0_WLSL 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX7GTR0_RESERVED_15_13 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX7GTR0_RESERVED_12_8 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX7GTR0_RESERVED_7_5 0x0 - - DQS Gating System Latency - PSU_DDR_PHY_DX7GTR0_DGSL 0x0 - - DATX8 n General Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD080EC0, 0xFFFFFFFFU ,0x00020000U) - RegMask = (DDR_PHY_DX7GTR0_RESERVED_31_24_MASK | DDR_PHY_DX7GTR0_WDQSL_MASK | DDR_PHY_DX7GTR0_RESERVED_23_20_MASK | DDR_PHY_DX7GTR0_WLSL_MASK | DDR_PHY_DX7GTR0_RESERVED_15_13_MASK | DDR_PHY_DX7GTR0_RESERVED_12_8_MASK | DDR_PHY_DX7GTR0_RESERVED_7_5_MASK | DDR_PHY_DX7GTR0_DGSL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX7GTR0_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX7GTR0_WDQSL_SHIFT - | 0x00000000U << DDR_PHY_DX7GTR0_RESERVED_23_20_SHIFT - | 0x00000002U << DDR_PHY_DX7GTR0_WLSL_SHIFT - | 0x00000000U << DDR_PHY_DX7GTR0_RESERVED_15_13_SHIFT - | 0x00000000U << DDR_PHY_DX7GTR0_RESERVED_12_8_SHIFT - | 0x00000000U << DDR_PHY_DX7GTR0_RESERVED_7_5_SHIFT - | 0x00000000U << DDR_PHY_DX7GTR0_DGSL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX7GTR0_OFFSET ,0xFFFFFFFFU ,0x00020000U); - /*############################################################################################################################ */ - - /*Register : DX8GCR0 @ 0XFD080F00</p> - - Calibration Bypass - PSU_DDR_PHY_DX8GCR0_CALBYP 0x0 - - Master Delay Line Enable - PSU_DDR_PHY_DX8GCR0_MDLEN 0x1 - - Configurable ODT(TE) Phase Shift - PSU_DDR_PHY_DX8GCR0_CODTSHFT 0x0 - - DQS Duty Cycle Correction - PSU_DDR_PHY_DX8GCR0_DQSDCC 0x0 - - Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY - PSU_DDR_PHY_DX8GCR0_RDDLY 0x8 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8GCR0_RESERVED_19_14 0x0 - - DQSNSE Power Down Receiver - PSU_DDR_PHY_DX8GCR0_DQSNSEPDR 0x0 - - DQSSE Power Down Receiver - PSU_DDR_PHY_DX8GCR0_DQSSEPDR 0x0 - - RTT On Additive Latency - PSU_DDR_PHY_DX8GCR0_RTTOAL 0x0 - - RTT Output Hold - PSU_DDR_PHY_DX8GCR0_RTTOH 0x3 - - Configurable PDR Phase Shift - PSU_DDR_PHY_DX8GCR0_CPDRSHFT 0x0 - - DQSR Power Down - PSU_DDR_PHY_DX8GCR0_DQSRPD 0x0 - - DQSG Power Down Receiver - PSU_DDR_PHY_DX8GCR0_DQSGPDR 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8GCR0_RESERVED_4 0x0 - - DQSG On-Die Termination - PSU_DDR_PHY_DX8GCR0_DQSGODT 0x0 - - DQSG Output Enable - PSU_DDR_PHY_DX8GCR0_DQSGOE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8GCR0_RESERVED_1_0 0x0 - - DATX8 n General Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD080F00, 0xFFFFFFFFU ,0x40800624U) - RegMask = (DDR_PHY_DX8GCR0_CALBYP_MASK | DDR_PHY_DX8GCR0_MDLEN_MASK | DDR_PHY_DX8GCR0_CODTSHFT_MASK | DDR_PHY_DX8GCR0_DQSDCC_MASK | DDR_PHY_DX8GCR0_RDDLY_MASK | DDR_PHY_DX8GCR0_RESERVED_19_14_MASK | DDR_PHY_DX8GCR0_DQSNSEPDR_MASK | DDR_PHY_DX8GCR0_DQSSEPDR_MASK | DDR_PHY_DX8GCR0_RTTOAL_MASK | DDR_PHY_DX8GCR0_RTTOH_MASK | DDR_PHY_DX8GCR0_CPDRSHFT_MASK | DDR_PHY_DX8GCR0_DQSRPD_MASK | DDR_PHY_DX8GCR0_DQSGPDR_MASK | DDR_PHY_DX8GCR0_RESERVED_4_MASK | DDR_PHY_DX8GCR0_DQSGODT_MASK | DDR_PHY_DX8GCR0_DQSGOE_MASK | DDR_PHY_DX8GCR0_RESERVED_1_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8GCR0_CALBYP_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR0_MDLEN_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_CODTSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_DQSDCC_SHIFT - | 0x00000008U << DDR_PHY_DX8GCR0_RDDLY_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_RESERVED_19_14_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_DQSNSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_DQSSEPDR_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_RTTOAL_SHIFT - | 0x00000003U << DDR_PHY_DX8GCR0_RTTOH_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_CPDRSHFT_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_DQSRPD_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR0_DQSGPDR_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_RESERVED_4_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_DQSGODT_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR0_DQSGOE_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR0_RESERVED_1_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8GCR0_OFFSET ,0xFFFFFFFFU ,0x40800624U); - /*############################################################################################################################ */ - - /*Register : DX8GCR1 @ 0XFD080F04</p> - - Enables the PDR mode for DQ[7:0] - PSU_DDR_PHY_DX8GCR1_DXPDRMODE 0x0 - - Reserved. Returns zeroes on reads. - PSU_DDR_PHY_DX8GCR1_RESERVED_15 0x0 - - Select the delayed or non-delayed read data strobe # - PSU_DDR_PHY_DX8GCR1_QSNSEL 0x1 - - Select the delayed or non-delayed read data strobe - PSU_DDR_PHY_DX8GCR1_QSSEL 0x1 - - Enables Read Data Strobe in a byte lane - PSU_DDR_PHY_DX8GCR1_OEEN 0x1 - - Enables PDR in a byte lane - PSU_DDR_PHY_DX8GCR1_PDREN 0x1 - - Enables ODT/TE in a byte lane - PSU_DDR_PHY_DX8GCR1_TEEN 0x1 - - Enables Write Data strobe in a byte lane - PSU_DDR_PHY_DX8GCR1_DSEN 0x1 - - Enables DM pin in a byte lane - PSU_DDR_PHY_DX8GCR1_DMEN 0x1 - - Enables DQ corresponding to each bit in a byte - PSU_DDR_PHY_DX8GCR1_DQEN 0x0 - - DATX8 n General Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD080F04, 0xFFFFFFFFU ,0x00007F00U) - RegMask = (DDR_PHY_DX8GCR1_DXPDRMODE_MASK | DDR_PHY_DX8GCR1_RESERVED_15_MASK | DDR_PHY_DX8GCR1_QSNSEL_MASK | DDR_PHY_DX8GCR1_QSSEL_MASK | DDR_PHY_DX8GCR1_OEEN_MASK | DDR_PHY_DX8GCR1_PDREN_MASK | DDR_PHY_DX8GCR1_TEEN_MASK | DDR_PHY_DX8GCR1_DSEN_MASK | DDR_PHY_DX8GCR1_DMEN_MASK | DDR_PHY_DX8GCR1_DQEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8GCR1_DXPDRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR1_RESERVED_15_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR1_QSNSEL_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR1_QSSEL_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR1_OEEN_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR1_PDREN_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR1_TEEN_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR1_DSEN_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR1_DMEN_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR1_DQEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8GCR1_OFFSET ,0xFFFFFFFFU ,0x00007F00U); - /*############################################################################################################################ */ - - /*Register : DX8GCR4 @ 0XFD080F10</p> - - Byte lane VREF IOM (Used only by D4MU IOs) - PSU_DDR_PHY_DX8GCR4_RESERVED_31_29 0x0 - - Byte Lane VREF Pad Enable - PSU_DDR_PHY_DX8GCR4_DXREFPEN 0x0 - - Byte Lane Internal VREF Enable - PSU_DDR_PHY_DX8GCR4_DXREFEEN 0x3 - - Byte Lane Single-End VREF Enable - PSU_DDR_PHY_DX8GCR4_DXREFSEN 0x1 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX8GCR4_RESERVED_24 0x0 - - External VREF generator REFSEL range select - PSU_DDR_PHY_DX8GCR4_DXREFESELRANGE 0x0 - - Byte Lane External VREF Select - PSU_DDR_PHY_DX8GCR4_DXREFESEL 0x0 - - Single ended VREF generator REFSEL range select - PSU_DDR_PHY_DX8GCR4_DXREFSSELRANGE 0x1 - - Byte Lane Single-End VREF Select - PSU_DDR_PHY_DX8GCR4_DXREFSSEL 0x30 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX8GCR4_RESERVED_7_6 0x0 - - VREF Enable control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX8GCR4_DXREFIEN 0xf - - VRMON control for DQ IO (Single Ended) buffers of a byte lane. - PSU_DDR_PHY_DX8GCR4_DXREFIMON 0x0 - - DATX8 n General Configuration Register 4 - (OFFSET, MASK, VALUE) (0XFD080F10, 0xFFFFFFFFU ,0x0E00B03CU) - RegMask = (DDR_PHY_DX8GCR4_RESERVED_31_29_MASK | DDR_PHY_DX8GCR4_DXREFPEN_MASK | DDR_PHY_DX8GCR4_DXREFEEN_MASK | DDR_PHY_DX8GCR4_DXREFSEN_MASK | DDR_PHY_DX8GCR4_RESERVED_24_MASK | DDR_PHY_DX8GCR4_DXREFESELRANGE_MASK | DDR_PHY_DX8GCR4_DXREFESEL_MASK | DDR_PHY_DX8GCR4_DXREFSSELRANGE_MASK | DDR_PHY_DX8GCR4_DXREFSSEL_MASK | DDR_PHY_DX8GCR4_RESERVED_7_6_MASK | DDR_PHY_DX8GCR4_DXREFIEN_MASK | DDR_PHY_DX8GCR4_DXREFIMON_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8GCR4_RESERVED_31_29_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR4_DXREFPEN_SHIFT - | 0x00000003U << DDR_PHY_DX8GCR4_DXREFEEN_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR4_DXREFSEN_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR4_RESERVED_24_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR4_DXREFESELRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR4_DXREFESEL_SHIFT - | 0x00000001U << DDR_PHY_DX8GCR4_DXREFSSELRANGE_SHIFT - | 0x00000030U << DDR_PHY_DX8GCR4_DXREFSSEL_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR4_RESERVED_7_6_SHIFT - | 0x0000000FU << DDR_PHY_DX8GCR4_DXREFIEN_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR4_DXREFIMON_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8GCR4_OFFSET ,0xFFFFFFFFU ,0x0E00B03CU); - /*############################################################################################################################ */ - - /*Register : DX8GCR5 @ 0XFD080F14</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX8GCR5_RESERVED_31 0x0 - - Byte Lane internal VREF Select for Rank 3 - PSU_DDR_PHY_DX8GCR5_DXREFISELR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX8GCR5_RESERVED_23 0x0 - - Byte Lane internal VREF Select for Rank 2 - PSU_DDR_PHY_DX8GCR5_DXREFISELR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX8GCR5_RESERVED_15 0x0 - - Byte Lane internal VREF Select for Rank 1 - PSU_DDR_PHY_DX8GCR5_DXREFISELR1 0x4f - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX8GCR5_RESERVED_7 0x0 - - Byte Lane internal VREF Select for Rank 0 - PSU_DDR_PHY_DX8GCR5_DXREFISELR0 0x4f - - DATX8 n General Configuration Register 5 - (OFFSET, MASK, VALUE) (0XFD080F14, 0xFFFFFFFFU ,0x09094F4FU) - RegMask = (DDR_PHY_DX8GCR5_RESERVED_31_MASK | DDR_PHY_DX8GCR5_DXREFISELR3_MASK | DDR_PHY_DX8GCR5_RESERVED_23_MASK | DDR_PHY_DX8GCR5_DXREFISELR2_MASK | DDR_PHY_DX8GCR5_RESERVED_15_MASK | DDR_PHY_DX8GCR5_DXREFISELR1_MASK | DDR_PHY_DX8GCR5_RESERVED_7_MASK | DDR_PHY_DX8GCR5_DXREFISELR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8GCR5_RESERVED_31_SHIFT - | 0x00000009U << DDR_PHY_DX8GCR5_DXREFISELR3_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR5_RESERVED_23_SHIFT - | 0x00000009U << DDR_PHY_DX8GCR5_DXREFISELR2_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR5_RESERVED_15_SHIFT - | 0x0000004FU << DDR_PHY_DX8GCR5_DXREFISELR1_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR5_RESERVED_7_SHIFT - | 0x0000004FU << DDR_PHY_DX8GCR5_DXREFISELR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8GCR5_OFFSET ,0xFFFFFFFFU ,0x09094F4FU); - /*############################################################################################################################ */ - - /*Register : DX8GCR6 @ 0XFD080F18</p> - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX8GCR6_RESERVED_31_30 0x0 - - DRAM DQ VREF Select for Rank3 - PSU_DDR_PHY_DX8GCR6_DXDQVREFR3 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX8GCR6_RESERVED_23_22 0x0 - - DRAM DQ VREF Select for Rank2 - PSU_DDR_PHY_DX8GCR6_DXDQVREFR2 0x9 - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX8GCR6_RESERVED_15_14 0x0 - - DRAM DQ VREF Select for Rank1 - PSU_DDR_PHY_DX8GCR6_DXDQVREFR1 0x2b - - Reserved. Returns zeros on reads. - PSU_DDR_PHY_DX8GCR6_RESERVED_7_6 0x0 - - DRAM DQ VREF Select for Rank0 - PSU_DDR_PHY_DX8GCR6_DXDQVREFR0 0x2b - - DATX8 n General Configuration Register 6 - (OFFSET, MASK, VALUE) (0XFD080F18, 0xFFFFFFFFU ,0x09092B2BU) - RegMask = (DDR_PHY_DX8GCR6_RESERVED_31_30_MASK | DDR_PHY_DX8GCR6_DXDQVREFR3_MASK | DDR_PHY_DX8GCR6_RESERVED_23_22_MASK | DDR_PHY_DX8GCR6_DXDQVREFR2_MASK | DDR_PHY_DX8GCR6_RESERVED_15_14_MASK | DDR_PHY_DX8GCR6_DXDQVREFR1_MASK | DDR_PHY_DX8GCR6_RESERVED_7_6_MASK | DDR_PHY_DX8GCR6_DXDQVREFR0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8GCR6_RESERVED_31_30_SHIFT - | 0x00000009U << DDR_PHY_DX8GCR6_DXDQVREFR3_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR6_RESERVED_23_22_SHIFT - | 0x00000009U << DDR_PHY_DX8GCR6_DXDQVREFR2_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR6_RESERVED_15_14_SHIFT - | 0x0000002BU << DDR_PHY_DX8GCR6_DXDQVREFR1_SHIFT - | 0x00000000U << DDR_PHY_DX8GCR6_RESERVED_7_6_SHIFT - | 0x0000002BU << DDR_PHY_DX8GCR6_DXDQVREFR0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8GCR6_OFFSET ,0xFFFFFFFFU ,0x09092B2BU); - /*############################################################################################################################ */ - - /*Register : DX8LCDLR2 @ 0XFD080F88</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8LCDLR2_RESERVED_31_25 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8LCDLR2_RESERVED_24_16 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8LCDLR2_RESERVED_15_9 0x0 - - Read DQS Gating Delay - PSU_DDR_PHY_DX8LCDLR2_DQSGD 0x0 - - DATX8 n Local Calibrated Delay Line Register 2 - (OFFSET, MASK, VALUE) (0XFD080F88, 0xFFFFFFFFU ,0x00000000U) - RegMask = (DDR_PHY_DX8LCDLR2_RESERVED_31_25_MASK | DDR_PHY_DX8LCDLR2_RESERVED_24_16_MASK | DDR_PHY_DX8LCDLR2_RESERVED_15_9_MASK | DDR_PHY_DX8LCDLR2_DQSGD_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8LCDLR2_RESERVED_31_25_SHIFT - | 0x00000000U << DDR_PHY_DX8LCDLR2_RESERVED_24_16_SHIFT - | 0x00000000U << DDR_PHY_DX8LCDLR2_RESERVED_15_9_SHIFT - | 0x00000000U << DDR_PHY_DX8LCDLR2_DQSGD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8LCDLR2_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DX8GTR0 @ 0XFD080FC0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8GTR0_RESERVED_31_24 0x0 - - DQ Write Path Latency Pipeline - PSU_DDR_PHY_DX8GTR0_WDQSL 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8GTR0_RESERVED_23_20 0x0 - - Write Leveling System Latency - PSU_DDR_PHY_DX8GTR0_WLSL 0x2 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8GTR0_RESERVED_15_13 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8GTR0_RESERVED_12_8 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8GTR0_RESERVED_7_5 0x0 - - DQS Gating System Latency - PSU_DDR_PHY_DX8GTR0_DGSL 0x0 - - DATX8 n General Timing Register 0 - (OFFSET, MASK, VALUE) (0XFD080FC0, 0xFFFFFFFFU ,0x00020000U) - RegMask = (DDR_PHY_DX8GTR0_RESERVED_31_24_MASK | DDR_PHY_DX8GTR0_WDQSL_MASK | DDR_PHY_DX8GTR0_RESERVED_23_20_MASK | DDR_PHY_DX8GTR0_WLSL_MASK | DDR_PHY_DX8GTR0_RESERVED_15_13_MASK | DDR_PHY_DX8GTR0_RESERVED_12_8_MASK | DDR_PHY_DX8GTR0_RESERVED_7_5_MASK | DDR_PHY_DX8GTR0_DGSL_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8GTR0_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX8GTR0_WDQSL_SHIFT - | 0x00000000U << DDR_PHY_DX8GTR0_RESERVED_23_20_SHIFT - | 0x00000002U << DDR_PHY_DX8GTR0_WLSL_SHIFT - | 0x00000000U << DDR_PHY_DX8GTR0_RESERVED_15_13_SHIFT - | 0x00000000U << DDR_PHY_DX8GTR0_RESERVED_12_8_SHIFT - | 0x00000000U << DDR_PHY_DX8GTR0_RESERVED_7_5_SHIFT - | 0x00000000U << DDR_PHY_DX8GTR0_DGSL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8GTR0_OFFSET ,0xFFFFFFFFU ,0x00020000U); - /*############################################################################################################################ */ - - /*Register : DX8SL0OSC @ 0XFD081400</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL0OSC_RESERVED_31_30 0x0 - - Enable Clock Gating for DX ddr_clk - PSU_DDR_PHY_DX8SL0OSC_GATEDXRDCLK 0x2 - - Enable Clock Gating for DX ctl_rd_clk - PSU_DDR_PHY_DX8SL0OSC_GATEDXDDRCLK 0x2 - - Enable Clock Gating for DX ctl_clk - PSU_DDR_PHY_DX8SL0OSC_GATEDXCTLCLK 0x2 - - Selects the level to which clocks will be stalled when clock gating is enabled. - PSU_DDR_PHY_DX8SL0OSC_CLKLEVEL 0x0 - - Loopback Mode - PSU_DDR_PHY_DX8SL0OSC_LBMODE 0x0 - - Load GSDQS LCDL with 2x the calibrated GSDQSPRD value - PSU_DDR_PHY_DX8SL0OSC_LBGSDQS 0x0 - - Loopback DQS Gating - PSU_DDR_PHY_DX8SL0OSC_LBGDQS 0x0 - - Loopback DQS Shift - PSU_DDR_PHY_DX8SL0OSC_LBDQSS 0x0 - - PHY High-Speed Reset - PSU_DDR_PHY_DX8SL0OSC_PHYHRST 0x1 - - PHY FIFO Reset - PSU_DDR_PHY_DX8SL0OSC_PHYFRST 0x1 - - Delay Line Test Start - PSU_DDR_PHY_DX8SL0OSC_DLTST 0x0 - - Delay Line Test Mode - PSU_DDR_PHY_DX8SL0OSC_DLTMODE 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8SL0OSC_RESERVED_12_11 0x3 - - Oscillator Mode Write-Data Delay Line Select - PSU_DDR_PHY_DX8SL0OSC_OSCWDDL 0x3 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8SL0OSC_RESERVED_8_7 0x3 - - Oscillator Mode Write-Leveling Delay Line Select - PSU_DDR_PHY_DX8SL0OSC_OSCWDL 0x3 - - Oscillator Mode Division - PSU_DDR_PHY_DX8SL0OSC_OSCDIV 0xf - - Oscillator Enable - PSU_DDR_PHY_DX8SL0OSC_OSCEN 0x0 - - DATX8 0-1 Oscillator, Delay Line Test, PHY FIFO and High Speed Reset, Loopback, and Gated Clock Control Register - (OFFSET, MASK, VALUE) (0XFD081400, 0xFFFFFFFFU ,0x2A019FFEU) - RegMask = (DDR_PHY_DX8SL0OSC_RESERVED_31_30_MASK | DDR_PHY_DX8SL0OSC_GATEDXRDCLK_MASK | DDR_PHY_DX8SL0OSC_GATEDXDDRCLK_MASK | DDR_PHY_DX8SL0OSC_GATEDXCTLCLK_MASK | DDR_PHY_DX8SL0OSC_CLKLEVEL_MASK | DDR_PHY_DX8SL0OSC_LBMODE_MASK | DDR_PHY_DX8SL0OSC_LBGSDQS_MASK | DDR_PHY_DX8SL0OSC_LBGDQS_MASK | DDR_PHY_DX8SL0OSC_LBDQSS_MASK | DDR_PHY_DX8SL0OSC_PHYHRST_MASK | DDR_PHY_DX8SL0OSC_PHYFRST_MASK | DDR_PHY_DX8SL0OSC_DLTST_MASK | DDR_PHY_DX8SL0OSC_DLTMODE_MASK | DDR_PHY_DX8SL0OSC_RESERVED_12_11_MASK | DDR_PHY_DX8SL0OSC_OSCWDDL_MASK | DDR_PHY_DX8SL0OSC_RESERVED_8_7_MASK | DDR_PHY_DX8SL0OSC_OSCWDL_MASK | DDR_PHY_DX8SL0OSC_OSCDIV_MASK | DDR_PHY_DX8SL0OSC_OSCEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL0OSC_RESERVED_31_30_SHIFT - | 0x00000002U << DDR_PHY_DX8SL0OSC_GATEDXRDCLK_SHIFT - | 0x00000002U << DDR_PHY_DX8SL0OSC_GATEDXDDRCLK_SHIFT - | 0x00000002U << DDR_PHY_DX8SL0OSC_GATEDXCTLCLK_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0OSC_CLKLEVEL_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0OSC_LBMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0OSC_LBGSDQS_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0OSC_LBGDQS_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0OSC_LBDQSS_SHIFT - | 0x00000001U << DDR_PHY_DX8SL0OSC_PHYHRST_SHIFT - | 0x00000001U << DDR_PHY_DX8SL0OSC_PHYFRST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0OSC_DLTST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0OSC_DLTMODE_SHIFT - | 0x00000003U << DDR_PHY_DX8SL0OSC_RESERVED_12_11_SHIFT - | 0x00000003U << DDR_PHY_DX8SL0OSC_OSCWDDL_SHIFT - | 0x00000003U << DDR_PHY_DX8SL0OSC_RESERVED_8_7_SHIFT - | 0x00000003U << DDR_PHY_DX8SL0OSC_OSCWDL_SHIFT - | 0x0000000FU << DDR_PHY_DX8SL0OSC_OSCDIV_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0OSC_OSCEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL0OSC_OFFSET ,0xFFFFFFFFU ,0x2A019FFEU); - /*############################################################################################################################ */ - - /*Register : DX8SL0DQSCTL @ 0XFD08141C</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25 0x0 - - Read Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SL0DQSCTL_RRRMODE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22 0x0 - - Write Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SL0DQSCTL_WRRMODE 0x1 - - DQS Gate Extension - PSU_DDR_PHY_DX8SL0DQSCTL_DQSGX 0x0 - - Low Power PLL Power Down - PSU_DDR_PHY_DX8SL0DQSCTL_LPPLLPD 0x1 - - Low Power I/O Power Down - PSU_DDR_PHY_DX8SL0DQSCTL_LPIOPD 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15 0x0 - - QS Counter Enable - PSU_DDR_PHY_DX8SL0DQSCTL_QSCNTEN 0x1 - - Unused DQ I/O Mode - PSU_DDR_PHY_DX8SL0DQSCTL_UDQIOM 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10 0x0 - - Data Slew Rate - PSU_DDR_PHY_DX8SL0DQSCTL_DXSR 0x3 - - DQS_N Resistor - PSU_DDR_PHY_DX8SL0DQSCTL_DQSNRES 0x0 - - DQS Resistor - PSU_DDR_PHY_DX8SL0DQSCTL_DQSRES 0x0 - - DATX8 0-1 DQS Control Register - (OFFSET, MASK, VALUE) (0XFD08141C, 0xFFFFFFFFU ,0x01264300U) - RegMask = (DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25_MASK | DDR_PHY_DX8SL0DQSCTL_RRRMODE_MASK | DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22_MASK | DDR_PHY_DX8SL0DQSCTL_WRRMODE_MASK | DDR_PHY_DX8SL0DQSCTL_DQSGX_MASK | DDR_PHY_DX8SL0DQSCTL_LPPLLPD_MASK | DDR_PHY_DX8SL0DQSCTL_LPIOPD_MASK | DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15_MASK | DDR_PHY_DX8SL0DQSCTL_QSCNTEN_MASK | DDR_PHY_DX8SL0DQSCTL_UDQIOM_MASK | DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10_MASK | DDR_PHY_DX8SL0DQSCTL_DXSR_MASK | DDR_PHY_DX8SL0DQSCTL_DQSNRES_MASK | DDR_PHY_DX8SL0DQSCTL_DQSRES_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25_SHIFT - | 0x00000001U << DDR_PHY_DX8SL0DQSCTL_RRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22_SHIFT - | 0x00000001U << DDR_PHY_DX8SL0DQSCTL_WRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DQSCTL_DQSGX_SHIFT - | 0x00000001U << DDR_PHY_DX8SL0DQSCTL_LPPLLPD_SHIFT - | 0x00000001U << DDR_PHY_DX8SL0DQSCTL_LPIOPD_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15_SHIFT - | 0x00000001U << DDR_PHY_DX8SL0DQSCTL_QSCNTEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DQSCTL_UDQIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10_SHIFT - | 0x00000003U << DDR_PHY_DX8SL0DQSCTL_DXSR_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DQSCTL_DQSNRES_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DQSCTL_DQSRES_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL0DQSCTL_OFFSET ,0xFFFFFFFFU ,0x01264300U); - /*############################################################################################################################ */ - - /*Register : DX8SL0DXCTL2 @ 0XFD08142C</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24 0x0 - - Configurable Read Data Enable - PSU_DDR_PHY_DX8SL0DXCTL2_CRDEN 0x0 - - OX Extension during Post-amble - PSU_DDR_PHY_DX8SL0DXCTL2_POSOEX 0x0 - - OE Extension during Pre-amble - PSU_DDR_PHY_DX8SL0DXCTL2_PREOEX 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_17 0x0 - - I/O Assisted Gate Select - PSU_DDR_PHY_DX8SL0DXCTL2_IOAG 0x0 - - I/O Loopback Select - PSU_DDR_PHY_DX8SL0DXCTL2_IOLB 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13 0x0 - - Low Power Wakeup Threshold - PSU_DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH 0xc - - Read Data Bus Inversion Enable - PSU_DDR_PHY_DX8SL0DXCTL2_RDBI 0x0 - - Write Data Bus Inversion Enable - PSU_DDR_PHY_DX8SL0DXCTL2_WDBI 0x0 - - PUB Read FIFO Bypass - PSU_DDR_PHY_DX8SL0DXCTL2_PRFBYP 0x0 - - DATX8 Receive FIFO Read Mode - PSU_DDR_PHY_DX8SL0DXCTL2_RDMODE 0x0 - - Disables the Read FIFO Reset - PSU_DDR_PHY_DX8SL0DXCTL2_DISRST 0x0 - - Read DQS Gate I/O Loopback - PSU_DDR_PHY_DX8SL0DXCTL2_DQSGLB 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL0DXCTL2_RESERVED_0 0x0 - - DATX8 0-1 DX Control Register 2 - (OFFSET, MASK, VALUE) (0XFD08142C, 0xFFFFFFFFU ,0x00041800U) - RegMask = (DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24_MASK | DDR_PHY_DX8SL0DXCTL2_CRDEN_MASK | DDR_PHY_DX8SL0DXCTL2_POSOEX_MASK | DDR_PHY_DX8SL0DXCTL2_PREOEX_MASK | DDR_PHY_DX8SL0DXCTL2_RESERVED_17_MASK | DDR_PHY_DX8SL0DXCTL2_IOAG_MASK | DDR_PHY_DX8SL0DXCTL2_IOLB_MASK | DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13_MASK | DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH_MASK | DDR_PHY_DX8SL0DXCTL2_RDBI_MASK | DDR_PHY_DX8SL0DXCTL2_WDBI_MASK | DDR_PHY_DX8SL0DXCTL2_PRFBYP_MASK | DDR_PHY_DX8SL0DXCTL2_RDMODE_MASK | DDR_PHY_DX8SL0DXCTL2_DISRST_MASK | DDR_PHY_DX8SL0DXCTL2_DQSGLB_MASK | DDR_PHY_DX8SL0DXCTL2_RESERVED_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_CRDEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_POSOEX_SHIFT - | 0x00000001U << DDR_PHY_DX8SL0DXCTL2_PREOEX_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_RESERVED_17_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_IOAG_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_IOLB_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13_SHIFT - | 0x0000000CU << DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_RDBI_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_WDBI_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_PRFBYP_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_RDMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_DISRST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_DQSGLB_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0DXCTL2_RESERVED_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL0DXCTL2_OFFSET ,0xFFFFFFFFU ,0x00041800U); - /*############################################################################################################################ */ - - /*Register : DX8SL0IOCR @ 0XFD081430</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL0IOCR_RESERVED_31 0x0 - - PVREF_DAC REFSEL range select - PSU_DDR_PHY_DX8SL0IOCR_DXDACRANGE 0x7 - - IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring - PSU_DDR_PHY_DX8SL0IOCR_DXVREFIOM 0x0 - - DX IO Mode - PSU_DDR_PHY_DX8SL0IOCR_DXIOM 0x2 - - DX IO Transmitter Mode - PSU_DDR_PHY_DX8SL0IOCR_DXTXM 0x0 - - DX IO Receiver Mode - PSU_DDR_PHY_DX8SL0IOCR_DXRXM 0x0 - - DATX8 0-1 I/O Configuration Register - (OFFSET, MASK, VALUE) (0XFD081430, 0xFFFFFFFFU ,0x70800000U) - RegMask = (DDR_PHY_DX8SL0IOCR_RESERVED_31_MASK | DDR_PHY_DX8SL0IOCR_DXDACRANGE_MASK | DDR_PHY_DX8SL0IOCR_DXVREFIOM_MASK | DDR_PHY_DX8SL0IOCR_DXIOM_MASK | DDR_PHY_DX8SL0IOCR_DXTXM_MASK | DDR_PHY_DX8SL0IOCR_DXRXM_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL0IOCR_RESERVED_31_SHIFT - | 0x00000007U << DDR_PHY_DX8SL0IOCR_DXDACRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0IOCR_DXVREFIOM_SHIFT - | 0x00000002U << DDR_PHY_DX8SL0IOCR_DXIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0IOCR_DXTXM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL0IOCR_DXRXM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL0IOCR_OFFSET ,0xFFFFFFFFU ,0x70800000U); - /*############################################################################################################################ */ - - /*Register : DX8SL1OSC @ 0XFD081440</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL1OSC_RESERVED_31_30 0x0 - - Enable Clock Gating for DX ddr_clk - PSU_DDR_PHY_DX8SL1OSC_GATEDXRDCLK 0x2 - - Enable Clock Gating for DX ctl_rd_clk - PSU_DDR_PHY_DX8SL1OSC_GATEDXDDRCLK 0x2 - - Enable Clock Gating for DX ctl_clk - PSU_DDR_PHY_DX8SL1OSC_GATEDXCTLCLK 0x2 - - Selects the level to which clocks will be stalled when clock gating is enabled. - PSU_DDR_PHY_DX8SL1OSC_CLKLEVEL 0x0 - - Loopback Mode - PSU_DDR_PHY_DX8SL1OSC_LBMODE 0x0 - - Load GSDQS LCDL with 2x the calibrated GSDQSPRD value - PSU_DDR_PHY_DX8SL1OSC_LBGSDQS 0x0 - - Loopback DQS Gating - PSU_DDR_PHY_DX8SL1OSC_LBGDQS 0x0 - - Loopback DQS Shift - PSU_DDR_PHY_DX8SL1OSC_LBDQSS 0x0 - - PHY High-Speed Reset - PSU_DDR_PHY_DX8SL1OSC_PHYHRST 0x1 - - PHY FIFO Reset - PSU_DDR_PHY_DX8SL1OSC_PHYFRST 0x1 - - Delay Line Test Start - PSU_DDR_PHY_DX8SL1OSC_DLTST 0x0 - - Delay Line Test Mode - PSU_DDR_PHY_DX8SL1OSC_DLTMODE 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8SL1OSC_RESERVED_12_11 0x3 - - Oscillator Mode Write-Data Delay Line Select - PSU_DDR_PHY_DX8SL1OSC_OSCWDDL 0x3 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8SL1OSC_RESERVED_8_7 0x3 - - Oscillator Mode Write-Leveling Delay Line Select - PSU_DDR_PHY_DX8SL1OSC_OSCWDL 0x3 - - Oscillator Mode Division - PSU_DDR_PHY_DX8SL1OSC_OSCDIV 0xf - - Oscillator Enable - PSU_DDR_PHY_DX8SL1OSC_OSCEN 0x0 - - DATX8 0-1 Oscillator, Delay Line Test, PHY FIFO and High Speed Reset, Loopback, and Gated Clock Control Register - (OFFSET, MASK, VALUE) (0XFD081440, 0xFFFFFFFFU ,0x2A019FFEU) - RegMask = (DDR_PHY_DX8SL1OSC_RESERVED_31_30_MASK | DDR_PHY_DX8SL1OSC_GATEDXRDCLK_MASK | DDR_PHY_DX8SL1OSC_GATEDXDDRCLK_MASK | DDR_PHY_DX8SL1OSC_GATEDXCTLCLK_MASK | DDR_PHY_DX8SL1OSC_CLKLEVEL_MASK | DDR_PHY_DX8SL1OSC_LBMODE_MASK | DDR_PHY_DX8SL1OSC_LBGSDQS_MASK | DDR_PHY_DX8SL1OSC_LBGDQS_MASK | DDR_PHY_DX8SL1OSC_LBDQSS_MASK | DDR_PHY_DX8SL1OSC_PHYHRST_MASK | DDR_PHY_DX8SL1OSC_PHYFRST_MASK | DDR_PHY_DX8SL1OSC_DLTST_MASK | DDR_PHY_DX8SL1OSC_DLTMODE_MASK | DDR_PHY_DX8SL1OSC_RESERVED_12_11_MASK | DDR_PHY_DX8SL1OSC_OSCWDDL_MASK | DDR_PHY_DX8SL1OSC_RESERVED_8_7_MASK | DDR_PHY_DX8SL1OSC_OSCWDL_MASK | DDR_PHY_DX8SL1OSC_OSCDIV_MASK | DDR_PHY_DX8SL1OSC_OSCEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL1OSC_RESERVED_31_30_SHIFT - | 0x00000002U << DDR_PHY_DX8SL1OSC_GATEDXRDCLK_SHIFT - | 0x00000002U << DDR_PHY_DX8SL1OSC_GATEDXDDRCLK_SHIFT - | 0x00000002U << DDR_PHY_DX8SL1OSC_GATEDXCTLCLK_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1OSC_CLKLEVEL_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1OSC_LBMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1OSC_LBGSDQS_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1OSC_LBGDQS_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1OSC_LBDQSS_SHIFT - | 0x00000001U << DDR_PHY_DX8SL1OSC_PHYHRST_SHIFT - | 0x00000001U << DDR_PHY_DX8SL1OSC_PHYFRST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1OSC_DLTST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1OSC_DLTMODE_SHIFT - | 0x00000003U << DDR_PHY_DX8SL1OSC_RESERVED_12_11_SHIFT - | 0x00000003U << DDR_PHY_DX8SL1OSC_OSCWDDL_SHIFT - | 0x00000003U << DDR_PHY_DX8SL1OSC_RESERVED_8_7_SHIFT - | 0x00000003U << DDR_PHY_DX8SL1OSC_OSCWDL_SHIFT - | 0x0000000FU << DDR_PHY_DX8SL1OSC_OSCDIV_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1OSC_OSCEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL1OSC_OFFSET ,0xFFFFFFFFU ,0x2A019FFEU); - /*############################################################################################################################ */ - - /*Register : DX8SL1DQSCTL @ 0XFD08145C</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25 0x0 - - Read Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SL1DQSCTL_RRRMODE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22 0x0 - - Write Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SL1DQSCTL_WRRMODE 0x1 - - DQS Gate Extension - PSU_DDR_PHY_DX8SL1DQSCTL_DQSGX 0x0 - - Low Power PLL Power Down - PSU_DDR_PHY_DX8SL1DQSCTL_LPPLLPD 0x1 - - Low Power I/O Power Down - PSU_DDR_PHY_DX8SL1DQSCTL_LPIOPD 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15 0x0 - - QS Counter Enable - PSU_DDR_PHY_DX8SL1DQSCTL_QSCNTEN 0x1 - - Unused DQ I/O Mode - PSU_DDR_PHY_DX8SL1DQSCTL_UDQIOM 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10 0x0 - - Data Slew Rate - PSU_DDR_PHY_DX8SL1DQSCTL_DXSR 0x3 - - DQS_N Resistor - PSU_DDR_PHY_DX8SL1DQSCTL_DQSNRES 0x0 - - DQS Resistor - PSU_DDR_PHY_DX8SL1DQSCTL_DQSRES 0x0 - - DATX8 0-1 DQS Control Register - (OFFSET, MASK, VALUE) (0XFD08145C, 0xFFFFFFFFU ,0x01264300U) - RegMask = (DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25_MASK | DDR_PHY_DX8SL1DQSCTL_RRRMODE_MASK | DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22_MASK | DDR_PHY_DX8SL1DQSCTL_WRRMODE_MASK | DDR_PHY_DX8SL1DQSCTL_DQSGX_MASK | DDR_PHY_DX8SL1DQSCTL_LPPLLPD_MASK | DDR_PHY_DX8SL1DQSCTL_LPIOPD_MASK | DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15_MASK | DDR_PHY_DX8SL1DQSCTL_QSCNTEN_MASK | DDR_PHY_DX8SL1DQSCTL_UDQIOM_MASK | DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10_MASK | DDR_PHY_DX8SL1DQSCTL_DXSR_MASK | DDR_PHY_DX8SL1DQSCTL_DQSNRES_MASK | DDR_PHY_DX8SL1DQSCTL_DQSRES_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25_SHIFT - | 0x00000001U << DDR_PHY_DX8SL1DQSCTL_RRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22_SHIFT - | 0x00000001U << DDR_PHY_DX8SL1DQSCTL_WRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DQSCTL_DQSGX_SHIFT - | 0x00000001U << DDR_PHY_DX8SL1DQSCTL_LPPLLPD_SHIFT - | 0x00000001U << DDR_PHY_DX8SL1DQSCTL_LPIOPD_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15_SHIFT - | 0x00000001U << DDR_PHY_DX8SL1DQSCTL_QSCNTEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DQSCTL_UDQIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10_SHIFT - | 0x00000003U << DDR_PHY_DX8SL1DQSCTL_DXSR_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DQSCTL_DQSNRES_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DQSCTL_DQSRES_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL1DQSCTL_OFFSET ,0xFFFFFFFFU ,0x01264300U); - /*############################################################################################################################ */ - - /*Register : DX8SL1DXCTL2 @ 0XFD08146C</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24 0x0 - - Configurable Read Data Enable - PSU_DDR_PHY_DX8SL1DXCTL2_CRDEN 0x0 - - OX Extension during Post-amble - PSU_DDR_PHY_DX8SL1DXCTL2_POSOEX 0x0 - - OE Extension during Pre-amble - PSU_DDR_PHY_DX8SL1DXCTL2_PREOEX 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_17 0x0 - - I/O Assisted Gate Select - PSU_DDR_PHY_DX8SL1DXCTL2_IOAG 0x0 - - I/O Loopback Select - PSU_DDR_PHY_DX8SL1DXCTL2_IOLB 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13 0x0 - - Low Power Wakeup Threshold - PSU_DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH 0xc - - Read Data Bus Inversion Enable - PSU_DDR_PHY_DX8SL1DXCTL2_RDBI 0x0 - - Write Data Bus Inversion Enable - PSU_DDR_PHY_DX8SL1DXCTL2_WDBI 0x0 - - PUB Read FIFO Bypass - PSU_DDR_PHY_DX8SL1DXCTL2_PRFBYP 0x0 - - DATX8 Receive FIFO Read Mode - PSU_DDR_PHY_DX8SL1DXCTL2_RDMODE 0x0 - - Disables the Read FIFO Reset - PSU_DDR_PHY_DX8SL1DXCTL2_DISRST 0x0 - - Read DQS Gate I/O Loopback - PSU_DDR_PHY_DX8SL1DXCTL2_DQSGLB 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL1DXCTL2_RESERVED_0 0x0 - - DATX8 0-1 DX Control Register 2 - (OFFSET, MASK, VALUE) (0XFD08146C, 0xFFFFFFFFU ,0x00041800U) - RegMask = (DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24_MASK | DDR_PHY_DX8SL1DXCTL2_CRDEN_MASK | DDR_PHY_DX8SL1DXCTL2_POSOEX_MASK | DDR_PHY_DX8SL1DXCTL2_PREOEX_MASK | DDR_PHY_DX8SL1DXCTL2_RESERVED_17_MASK | DDR_PHY_DX8SL1DXCTL2_IOAG_MASK | DDR_PHY_DX8SL1DXCTL2_IOLB_MASK | DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13_MASK | DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH_MASK | DDR_PHY_DX8SL1DXCTL2_RDBI_MASK | DDR_PHY_DX8SL1DXCTL2_WDBI_MASK | DDR_PHY_DX8SL1DXCTL2_PRFBYP_MASK | DDR_PHY_DX8SL1DXCTL2_RDMODE_MASK | DDR_PHY_DX8SL1DXCTL2_DISRST_MASK | DDR_PHY_DX8SL1DXCTL2_DQSGLB_MASK | DDR_PHY_DX8SL1DXCTL2_RESERVED_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_CRDEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_POSOEX_SHIFT - | 0x00000001U << DDR_PHY_DX8SL1DXCTL2_PREOEX_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_RESERVED_17_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_IOAG_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_IOLB_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13_SHIFT - | 0x0000000CU << DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_RDBI_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_WDBI_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_PRFBYP_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_RDMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_DISRST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_DQSGLB_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1DXCTL2_RESERVED_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL1DXCTL2_OFFSET ,0xFFFFFFFFU ,0x00041800U); - /*############################################################################################################################ */ - - /*Register : DX8SL1IOCR @ 0XFD081470</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL1IOCR_RESERVED_31 0x0 - - PVREF_DAC REFSEL range select - PSU_DDR_PHY_DX8SL1IOCR_DXDACRANGE 0x7 - - IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring - PSU_DDR_PHY_DX8SL1IOCR_DXVREFIOM 0x0 - - DX IO Mode - PSU_DDR_PHY_DX8SL1IOCR_DXIOM 0x2 - - DX IO Transmitter Mode - PSU_DDR_PHY_DX8SL1IOCR_DXTXM 0x0 - - DX IO Receiver Mode - PSU_DDR_PHY_DX8SL1IOCR_DXRXM 0x0 - - DATX8 0-1 I/O Configuration Register - (OFFSET, MASK, VALUE) (0XFD081470, 0xFFFFFFFFU ,0x70800000U) - RegMask = (DDR_PHY_DX8SL1IOCR_RESERVED_31_MASK | DDR_PHY_DX8SL1IOCR_DXDACRANGE_MASK | DDR_PHY_DX8SL1IOCR_DXVREFIOM_MASK | DDR_PHY_DX8SL1IOCR_DXIOM_MASK | DDR_PHY_DX8SL1IOCR_DXTXM_MASK | DDR_PHY_DX8SL1IOCR_DXRXM_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL1IOCR_RESERVED_31_SHIFT - | 0x00000007U << DDR_PHY_DX8SL1IOCR_DXDACRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1IOCR_DXVREFIOM_SHIFT - | 0x00000002U << DDR_PHY_DX8SL1IOCR_DXIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1IOCR_DXTXM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL1IOCR_DXRXM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL1IOCR_OFFSET ,0xFFFFFFFFU ,0x70800000U); - /*############################################################################################################################ */ - - /*Register : DX8SL2OSC @ 0XFD081480</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL2OSC_RESERVED_31_30 0x0 - - Enable Clock Gating for DX ddr_clk - PSU_DDR_PHY_DX8SL2OSC_GATEDXRDCLK 0x2 - - Enable Clock Gating for DX ctl_rd_clk - PSU_DDR_PHY_DX8SL2OSC_GATEDXDDRCLK 0x2 - - Enable Clock Gating for DX ctl_clk - PSU_DDR_PHY_DX8SL2OSC_GATEDXCTLCLK 0x2 - - Selects the level to which clocks will be stalled when clock gating is enabled. - PSU_DDR_PHY_DX8SL2OSC_CLKLEVEL 0x0 - - Loopback Mode - PSU_DDR_PHY_DX8SL2OSC_LBMODE 0x0 - - Load GSDQS LCDL with 2x the calibrated GSDQSPRD value - PSU_DDR_PHY_DX8SL2OSC_LBGSDQS 0x0 - - Loopback DQS Gating - PSU_DDR_PHY_DX8SL2OSC_LBGDQS 0x0 - - Loopback DQS Shift - PSU_DDR_PHY_DX8SL2OSC_LBDQSS 0x0 - - PHY High-Speed Reset - PSU_DDR_PHY_DX8SL2OSC_PHYHRST 0x1 - - PHY FIFO Reset - PSU_DDR_PHY_DX8SL2OSC_PHYFRST 0x1 - - Delay Line Test Start - PSU_DDR_PHY_DX8SL2OSC_DLTST 0x0 - - Delay Line Test Mode - PSU_DDR_PHY_DX8SL2OSC_DLTMODE 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8SL2OSC_RESERVED_12_11 0x3 - - Oscillator Mode Write-Data Delay Line Select - PSU_DDR_PHY_DX8SL2OSC_OSCWDDL 0x3 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8SL2OSC_RESERVED_8_7 0x3 - - Oscillator Mode Write-Leveling Delay Line Select - PSU_DDR_PHY_DX8SL2OSC_OSCWDL 0x3 - - Oscillator Mode Division - PSU_DDR_PHY_DX8SL2OSC_OSCDIV 0xf - - Oscillator Enable - PSU_DDR_PHY_DX8SL2OSC_OSCEN 0x0 - - DATX8 0-1 Oscillator, Delay Line Test, PHY FIFO and High Speed Reset, Loopback, and Gated Clock Control Register - (OFFSET, MASK, VALUE) (0XFD081480, 0xFFFFFFFFU ,0x2A019FFEU) - RegMask = (DDR_PHY_DX8SL2OSC_RESERVED_31_30_MASK | DDR_PHY_DX8SL2OSC_GATEDXRDCLK_MASK | DDR_PHY_DX8SL2OSC_GATEDXDDRCLK_MASK | DDR_PHY_DX8SL2OSC_GATEDXCTLCLK_MASK | DDR_PHY_DX8SL2OSC_CLKLEVEL_MASK | DDR_PHY_DX8SL2OSC_LBMODE_MASK | DDR_PHY_DX8SL2OSC_LBGSDQS_MASK | DDR_PHY_DX8SL2OSC_LBGDQS_MASK | DDR_PHY_DX8SL2OSC_LBDQSS_MASK | DDR_PHY_DX8SL2OSC_PHYHRST_MASK | DDR_PHY_DX8SL2OSC_PHYFRST_MASK | DDR_PHY_DX8SL2OSC_DLTST_MASK | DDR_PHY_DX8SL2OSC_DLTMODE_MASK | DDR_PHY_DX8SL2OSC_RESERVED_12_11_MASK | DDR_PHY_DX8SL2OSC_OSCWDDL_MASK | DDR_PHY_DX8SL2OSC_RESERVED_8_7_MASK | DDR_PHY_DX8SL2OSC_OSCWDL_MASK | DDR_PHY_DX8SL2OSC_OSCDIV_MASK | DDR_PHY_DX8SL2OSC_OSCEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL2OSC_RESERVED_31_30_SHIFT - | 0x00000002U << DDR_PHY_DX8SL2OSC_GATEDXRDCLK_SHIFT - | 0x00000002U << DDR_PHY_DX8SL2OSC_GATEDXDDRCLK_SHIFT - | 0x00000002U << DDR_PHY_DX8SL2OSC_GATEDXCTLCLK_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2OSC_CLKLEVEL_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2OSC_LBMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2OSC_LBGSDQS_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2OSC_LBGDQS_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2OSC_LBDQSS_SHIFT - | 0x00000001U << DDR_PHY_DX8SL2OSC_PHYHRST_SHIFT - | 0x00000001U << DDR_PHY_DX8SL2OSC_PHYFRST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2OSC_DLTST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2OSC_DLTMODE_SHIFT - | 0x00000003U << DDR_PHY_DX8SL2OSC_RESERVED_12_11_SHIFT - | 0x00000003U << DDR_PHY_DX8SL2OSC_OSCWDDL_SHIFT - | 0x00000003U << DDR_PHY_DX8SL2OSC_RESERVED_8_7_SHIFT - | 0x00000003U << DDR_PHY_DX8SL2OSC_OSCWDL_SHIFT - | 0x0000000FU << DDR_PHY_DX8SL2OSC_OSCDIV_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2OSC_OSCEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL2OSC_OFFSET ,0xFFFFFFFFU ,0x2A019FFEU); - /*############################################################################################################################ */ - - /*Register : DX8SL2DQSCTL @ 0XFD08149C</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25 0x0 - - Read Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SL2DQSCTL_RRRMODE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22 0x0 - - Write Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SL2DQSCTL_WRRMODE 0x1 - - DQS Gate Extension - PSU_DDR_PHY_DX8SL2DQSCTL_DQSGX 0x0 - - Low Power PLL Power Down - PSU_DDR_PHY_DX8SL2DQSCTL_LPPLLPD 0x1 - - Low Power I/O Power Down - PSU_DDR_PHY_DX8SL2DQSCTL_LPIOPD 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15 0x0 - - QS Counter Enable - PSU_DDR_PHY_DX8SL2DQSCTL_QSCNTEN 0x1 - - Unused DQ I/O Mode - PSU_DDR_PHY_DX8SL2DQSCTL_UDQIOM 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10 0x0 - - Data Slew Rate - PSU_DDR_PHY_DX8SL2DQSCTL_DXSR 0x3 - - DQS_N Resistor - PSU_DDR_PHY_DX8SL2DQSCTL_DQSNRES 0x0 - - DQS Resistor - PSU_DDR_PHY_DX8SL2DQSCTL_DQSRES 0x0 - - DATX8 0-1 DQS Control Register - (OFFSET, MASK, VALUE) (0XFD08149C, 0xFFFFFFFFU ,0x01264300U) - RegMask = (DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25_MASK | DDR_PHY_DX8SL2DQSCTL_RRRMODE_MASK | DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22_MASK | DDR_PHY_DX8SL2DQSCTL_WRRMODE_MASK | DDR_PHY_DX8SL2DQSCTL_DQSGX_MASK | DDR_PHY_DX8SL2DQSCTL_LPPLLPD_MASK | DDR_PHY_DX8SL2DQSCTL_LPIOPD_MASK | DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15_MASK | DDR_PHY_DX8SL2DQSCTL_QSCNTEN_MASK | DDR_PHY_DX8SL2DQSCTL_UDQIOM_MASK | DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10_MASK | DDR_PHY_DX8SL2DQSCTL_DXSR_MASK | DDR_PHY_DX8SL2DQSCTL_DQSNRES_MASK | DDR_PHY_DX8SL2DQSCTL_DQSRES_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25_SHIFT - | 0x00000001U << DDR_PHY_DX8SL2DQSCTL_RRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22_SHIFT - | 0x00000001U << DDR_PHY_DX8SL2DQSCTL_WRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DQSCTL_DQSGX_SHIFT - | 0x00000001U << DDR_PHY_DX8SL2DQSCTL_LPPLLPD_SHIFT - | 0x00000001U << DDR_PHY_DX8SL2DQSCTL_LPIOPD_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15_SHIFT - | 0x00000001U << DDR_PHY_DX8SL2DQSCTL_QSCNTEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DQSCTL_UDQIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10_SHIFT - | 0x00000003U << DDR_PHY_DX8SL2DQSCTL_DXSR_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DQSCTL_DQSNRES_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DQSCTL_DQSRES_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL2DQSCTL_OFFSET ,0xFFFFFFFFU ,0x01264300U); - /*############################################################################################################################ */ - - /*Register : DX8SL2DXCTL2 @ 0XFD0814AC</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24 0x0 - - Configurable Read Data Enable - PSU_DDR_PHY_DX8SL2DXCTL2_CRDEN 0x0 - - OX Extension during Post-amble - PSU_DDR_PHY_DX8SL2DXCTL2_POSOEX 0x0 - - OE Extension during Pre-amble - PSU_DDR_PHY_DX8SL2DXCTL2_PREOEX 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_17 0x0 - - I/O Assisted Gate Select - PSU_DDR_PHY_DX8SL2DXCTL2_IOAG 0x0 - - I/O Loopback Select - PSU_DDR_PHY_DX8SL2DXCTL2_IOLB 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13 0x0 - - Low Power Wakeup Threshold - PSU_DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH 0xc - - Read Data Bus Inversion Enable - PSU_DDR_PHY_DX8SL2DXCTL2_RDBI 0x0 - - Write Data Bus Inversion Enable - PSU_DDR_PHY_DX8SL2DXCTL2_WDBI 0x0 - - PUB Read FIFO Bypass - PSU_DDR_PHY_DX8SL2DXCTL2_PRFBYP 0x0 - - DATX8 Receive FIFO Read Mode - PSU_DDR_PHY_DX8SL2DXCTL2_RDMODE 0x0 - - Disables the Read FIFO Reset - PSU_DDR_PHY_DX8SL2DXCTL2_DISRST 0x0 - - Read DQS Gate I/O Loopback - PSU_DDR_PHY_DX8SL2DXCTL2_DQSGLB 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL2DXCTL2_RESERVED_0 0x0 - - DATX8 0-1 DX Control Register 2 - (OFFSET, MASK, VALUE) (0XFD0814AC, 0xFFFFFFFFU ,0x00041800U) - RegMask = (DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24_MASK | DDR_PHY_DX8SL2DXCTL2_CRDEN_MASK | DDR_PHY_DX8SL2DXCTL2_POSOEX_MASK | DDR_PHY_DX8SL2DXCTL2_PREOEX_MASK | DDR_PHY_DX8SL2DXCTL2_RESERVED_17_MASK | DDR_PHY_DX8SL2DXCTL2_IOAG_MASK | DDR_PHY_DX8SL2DXCTL2_IOLB_MASK | DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13_MASK | DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH_MASK | DDR_PHY_DX8SL2DXCTL2_RDBI_MASK | DDR_PHY_DX8SL2DXCTL2_WDBI_MASK | DDR_PHY_DX8SL2DXCTL2_PRFBYP_MASK | DDR_PHY_DX8SL2DXCTL2_RDMODE_MASK | DDR_PHY_DX8SL2DXCTL2_DISRST_MASK | DDR_PHY_DX8SL2DXCTL2_DQSGLB_MASK | DDR_PHY_DX8SL2DXCTL2_RESERVED_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_CRDEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_POSOEX_SHIFT - | 0x00000001U << DDR_PHY_DX8SL2DXCTL2_PREOEX_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_RESERVED_17_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_IOAG_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_IOLB_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13_SHIFT - | 0x0000000CU << DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_RDBI_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_WDBI_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_PRFBYP_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_RDMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_DISRST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_DQSGLB_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2DXCTL2_RESERVED_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL2DXCTL2_OFFSET ,0xFFFFFFFFU ,0x00041800U); - /*############################################################################################################################ */ - - /*Register : DX8SL2IOCR @ 0XFD0814B0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL2IOCR_RESERVED_31 0x0 - - PVREF_DAC REFSEL range select - PSU_DDR_PHY_DX8SL2IOCR_DXDACRANGE 0x7 - - IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring - PSU_DDR_PHY_DX8SL2IOCR_DXVREFIOM 0x0 - - DX IO Mode - PSU_DDR_PHY_DX8SL2IOCR_DXIOM 0x2 - - DX IO Transmitter Mode - PSU_DDR_PHY_DX8SL2IOCR_DXTXM 0x0 - - DX IO Receiver Mode - PSU_DDR_PHY_DX8SL2IOCR_DXRXM 0x0 - - DATX8 0-1 I/O Configuration Register - (OFFSET, MASK, VALUE) (0XFD0814B0, 0xFFFFFFFFU ,0x70800000U) - RegMask = (DDR_PHY_DX8SL2IOCR_RESERVED_31_MASK | DDR_PHY_DX8SL2IOCR_DXDACRANGE_MASK | DDR_PHY_DX8SL2IOCR_DXVREFIOM_MASK | DDR_PHY_DX8SL2IOCR_DXIOM_MASK | DDR_PHY_DX8SL2IOCR_DXTXM_MASK | DDR_PHY_DX8SL2IOCR_DXRXM_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL2IOCR_RESERVED_31_SHIFT - | 0x00000007U << DDR_PHY_DX8SL2IOCR_DXDACRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2IOCR_DXVREFIOM_SHIFT - | 0x00000002U << DDR_PHY_DX8SL2IOCR_DXIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2IOCR_DXTXM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL2IOCR_DXRXM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL2IOCR_OFFSET ,0xFFFFFFFFU ,0x70800000U); - /*############################################################################################################################ */ - - /*Register : DX8SL3OSC @ 0XFD0814C0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL3OSC_RESERVED_31_30 0x0 - - Enable Clock Gating for DX ddr_clk - PSU_DDR_PHY_DX8SL3OSC_GATEDXRDCLK 0x2 - - Enable Clock Gating for DX ctl_rd_clk - PSU_DDR_PHY_DX8SL3OSC_GATEDXDDRCLK 0x2 - - Enable Clock Gating for DX ctl_clk - PSU_DDR_PHY_DX8SL3OSC_GATEDXCTLCLK 0x2 - - Selects the level to which clocks will be stalled when clock gating is enabled. - PSU_DDR_PHY_DX8SL3OSC_CLKLEVEL 0x0 - - Loopback Mode - PSU_DDR_PHY_DX8SL3OSC_LBMODE 0x0 - - Load GSDQS LCDL with 2x the calibrated GSDQSPRD value - PSU_DDR_PHY_DX8SL3OSC_LBGSDQS 0x0 - - Loopback DQS Gating - PSU_DDR_PHY_DX8SL3OSC_LBGDQS 0x0 - - Loopback DQS Shift - PSU_DDR_PHY_DX8SL3OSC_LBDQSS 0x0 - - PHY High-Speed Reset - PSU_DDR_PHY_DX8SL3OSC_PHYHRST 0x1 - - PHY FIFO Reset - PSU_DDR_PHY_DX8SL3OSC_PHYFRST 0x1 - - Delay Line Test Start - PSU_DDR_PHY_DX8SL3OSC_DLTST 0x0 - - Delay Line Test Mode - PSU_DDR_PHY_DX8SL3OSC_DLTMODE 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8SL3OSC_RESERVED_12_11 0x3 - - Oscillator Mode Write-Data Delay Line Select - PSU_DDR_PHY_DX8SL3OSC_OSCWDDL 0x3 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8SL3OSC_RESERVED_8_7 0x3 - - Oscillator Mode Write-Leveling Delay Line Select - PSU_DDR_PHY_DX8SL3OSC_OSCWDL 0x3 - - Oscillator Mode Division - PSU_DDR_PHY_DX8SL3OSC_OSCDIV 0xf - - Oscillator Enable - PSU_DDR_PHY_DX8SL3OSC_OSCEN 0x0 - - DATX8 0-1 Oscillator, Delay Line Test, PHY FIFO and High Speed Reset, Loopback, and Gated Clock Control Register - (OFFSET, MASK, VALUE) (0XFD0814C0, 0xFFFFFFFFU ,0x2A019FFEU) - RegMask = (DDR_PHY_DX8SL3OSC_RESERVED_31_30_MASK | DDR_PHY_DX8SL3OSC_GATEDXRDCLK_MASK | DDR_PHY_DX8SL3OSC_GATEDXDDRCLK_MASK | DDR_PHY_DX8SL3OSC_GATEDXCTLCLK_MASK | DDR_PHY_DX8SL3OSC_CLKLEVEL_MASK | DDR_PHY_DX8SL3OSC_LBMODE_MASK | DDR_PHY_DX8SL3OSC_LBGSDQS_MASK | DDR_PHY_DX8SL3OSC_LBGDQS_MASK | DDR_PHY_DX8SL3OSC_LBDQSS_MASK | DDR_PHY_DX8SL3OSC_PHYHRST_MASK | DDR_PHY_DX8SL3OSC_PHYFRST_MASK | DDR_PHY_DX8SL3OSC_DLTST_MASK | DDR_PHY_DX8SL3OSC_DLTMODE_MASK | DDR_PHY_DX8SL3OSC_RESERVED_12_11_MASK | DDR_PHY_DX8SL3OSC_OSCWDDL_MASK | DDR_PHY_DX8SL3OSC_RESERVED_8_7_MASK | DDR_PHY_DX8SL3OSC_OSCWDL_MASK | DDR_PHY_DX8SL3OSC_OSCDIV_MASK | DDR_PHY_DX8SL3OSC_OSCEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL3OSC_RESERVED_31_30_SHIFT - | 0x00000002U << DDR_PHY_DX8SL3OSC_GATEDXRDCLK_SHIFT - | 0x00000002U << DDR_PHY_DX8SL3OSC_GATEDXDDRCLK_SHIFT - | 0x00000002U << DDR_PHY_DX8SL3OSC_GATEDXCTLCLK_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3OSC_CLKLEVEL_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3OSC_LBMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3OSC_LBGSDQS_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3OSC_LBGDQS_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3OSC_LBDQSS_SHIFT - | 0x00000001U << DDR_PHY_DX8SL3OSC_PHYHRST_SHIFT - | 0x00000001U << DDR_PHY_DX8SL3OSC_PHYFRST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3OSC_DLTST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3OSC_DLTMODE_SHIFT - | 0x00000003U << DDR_PHY_DX8SL3OSC_RESERVED_12_11_SHIFT - | 0x00000003U << DDR_PHY_DX8SL3OSC_OSCWDDL_SHIFT - | 0x00000003U << DDR_PHY_DX8SL3OSC_RESERVED_8_7_SHIFT - | 0x00000003U << DDR_PHY_DX8SL3OSC_OSCWDL_SHIFT - | 0x0000000FU << DDR_PHY_DX8SL3OSC_OSCDIV_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3OSC_OSCEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL3OSC_OFFSET ,0xFFFFFFFFU ,0x2A019FFEU); - /*############################################################################################################################ */ - - /*Register : DX8SL3DQSCTL @ 0XFD0814DC</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25 0x0 - - Read Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SL3DQSCTL_RRRMODE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22 0x0 - - Write Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SL3DQSCTL_WRRMODE 0x1 - - DQS Gate Extension - PSU_DDR_PHY_DX8SL3DQSCTL_DQSGX 0x0 - - Low Power PLL Power Down - PSU_DDR_PHY_DX8SL3DQSCTL_LPPLLPD 0x1 - - Low Power I/O Power Down - PSU_DDR_PHY_DX8SL3DQSCTL_LPIOPD 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15 0x0 - - QS Counter Enable - PSU_DDR_PHY_DX8SL3DQSCTL_QSCNTEN 0x1 - - Unused DQ I/O Mode - PSU_DDR_PHY_DX8SL3DQSCTL_UDQIOM 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10 0x0 - - Data Slew Rate - PSU_DDR_PHY_DX8SL3DQSCTL_DXSR 0x3 - - DQS_N Resistor - PSU_DDR_PHY_DX8SL3DQSCTL_DQSNRES 0x0 - - DQS Resistor - PSU_DDR_PHY_DX8SL3DQSCTL_DQSRES 0x0 - - DATX8 0-1 DQS Control Register - (OFFSET, MASK, VALUE) (0XFD0814DC, 0xFFFFFFFFU ,0x01264300U) - RegMask = (DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25_MASK | DDR_PHY_DX8SL3DQSCTL_RRRMODE_MASK | DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22_MASK | DDR_PHY_DX8SL3DQSCTL_WRRMODE_MASK | DDR_PHY_DX8SL3DQSCTL_DQSGX_MASK | DDR_PHY_DX8SL3DQSCTL_LPPLLPD_MASK | DDR_PHY_DX8SL3DQSCTL_LPIOPD_MASK | DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15_MASK | DDR_PHY_DX8SL3DQSCTL_QSCNTEN_MASK | DDR_PHY_DX8SL3DQSCTL_UDQIOM_MASK | DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10_MASK | DDR_PHY_DX8SL3DQSCTL_DXSR_MASK | DDR_PHY_DX8SL3DQSCTL_DQSNRES_MASK | DDR_PHY_DX8SL3DQSCTL_DQSRES_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25_SHIFT - | 0x00000001U << DDR_PHY_DX8SL3DQSCTL_RRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22_SHIFT - | 0x00000001U << DDR_PHY_DX8SL3DQSCTL_WRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DQSCTL_DQSGX_SHIFT - | 0x00000001U << DDR_PHY_DX8SL3DQSCTL_LPPLLPD_SHIFT - | 0x00000001U << DDR_PHY_DX8SL3DQSCTL_LPIOPD_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15_SHIFT - | 0x00000001U << DDR_PHY_DX8SL3DQSCTL_QSCNTEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DQSCTL_UDQIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10_SHIFT - | 0x00000003U << DDR_PHY_DX8SL3DQSCTL_DXSR_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DQSCTL_DQSNRES_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DQSCTL_DQSRES_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL3DQSCTL_OFFSET ,0xFFFFFFFFU ,0x01264300U); - /*############################################################################################################################ */ - - /*Register : DX8SL3DXCTL2 @ 0XFD0814EC</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24 0x0 - - Configurable Read Data Enable - PSU_DDR_PHY_DX8SL3DXCTL2_CRDEN 0x0 - - OX Extension during Post-amble - PSU_DDR_PHY_DX8SL3DXCTL2_POSOEX 0x0 - - OE Extension during Pre-amble - PSU_DDR_PHY_DX8SL3DXCTL2_PREOEX 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_17 0x0 - - I/O Assisted Gate Select - PSU_DDR_PHY_DX8SL3DXCTL2_IOAG 0x0 - - I/O Loopback Select - PSU_DDR_PHY_DX8SL3DXCTL2_IOLB 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13 0x0 - - Low Power Wakeup Threshold - PSU_DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH 0xc - - Read Data Bus Inversion Enable - PSU_DDR_PHY_DX8SL3DXCTL2_RDBI 0x0 - - Write Data Bus Inversion Enable - PSU_DDR_PHY_DX8SL3DXCTL2_WDBI 0x0 - - PUB Read FIFO Bypass - PSU_DDR_PHY_DX8SL3DXCTL2_PRFBYP 0x0 - - DATX8 Receive FIFO Read Mode - PSU_DDR_PHY_DX8SL3DXCTL2_RDMODE 0x0 - - Disables the Read FIFO Reset - PSU_DDR_PHY_DX8SL3DXCTL2_DISRST 0x0 - - Read DQS Gate I/O Loopback - PSU_DDR_PHY_DX8SL3DXCTL2_DQSGLB 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL3DXCTL2_RESERVED_0 0x0 - - DATX8 0-1 DX Control Register 2 - (OFFSET, MASK, VALUE) (0XFD0814EC, 0xFFFFFFFFU ,0x00041800U) - RegMask = (DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24_MASK | DDR_PHY_DX8SL3DXCTL2_CRDEN_MASK | DDR_PHY_DX8SL3DXCTL2_POSOEX_MASK | DDR_PHY_DX8SL3DXCTL2_PREOEX_MASK | DDR_PHY_DX8SL3DXCTL2_RESERVED_17_MASK | DDR_PHY_DX8SL3DXCTL2_IOAG_MASK | DDR_PHY_DX8SL3DXCTL2_IOLB_MASK | DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13_MASK | DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH_MASK | DDR_PHY_DX8SL3DXCTL2_RDBI_MASK | DDR_PHY_DX8SL3DXCTL2_WDBI_MASK | DDR_PHY_DX8SL3DXCTL2_PRFBYP_MASK | DDR_PHY_DX8SL3DXCTL2_RDMODE_MASK | DDR_PHY_DX8SL3DXCTL2_DISRST_MASK | DDR_PHY_DX8SL3DXCTL2_DQSGLB_MASK | DDR_PHY_DX8SL3DXCTL2_RESERVED_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_CRDEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_POSOEX_SHIFT - | 0x00000001U << DDR_PHY_DX8SL3DXCTL2_PREOEX_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_RESERVED_17_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_IOAG_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_IOLB_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13_SHIFT - | 0x0000000CU << DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_RDBI_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_WDBI_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_PRFBYP_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_RDMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_DISRST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_DQSGLB_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3DXCTL2_RESERVED_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL3DXCTL2_OFFSET ,0xFFFFFFFFU ,0x00041800U); - /*############################################################################################################################ */ - - /*Register : DX8SL3IOCR @ 0XFD0814F0</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL3IOCR_RESERVED_31 0x0 - - PVREF_DAC REFSEL range select - PSU_DDR_PHY_DX8SL3IOCR_DXDACRANGE 0x7 - - IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring - PSU_DDR_PHY_DX8SL3IOCR_DXVREFIOM 0x0 - - DX IO Mode - PSU_DDR_PHY_DX8SL3IOCR_DXIOM 0x2 - - DX IO Transmitter Mode - PSU_DDR_PHY_DX8SL3IOCR_DXTXM 0x0 - - DX IO Receiver Mode - PSU_DDR_PHY_DX8SL3IOCR_DXRXM 0x0 - - DATX8 0-1 I/O Configuration Register - (OFFSET, MASK, VALUE) (0XFD0814F0, 0xFFFFFFFFU ,0x70800000U) - RegMask = (DDR_PHY_DX8SL3IOCR_RESERVED_31_MASK | DDR_PHY_DX8SL3IOCR_DXDACRANGE_MASK | DDR_PHY_DX8SL3IOCR_DXVREFIOM_MASK | DDR_PHY_DX8SL3IOCR_DXIOM_MASK | DDR_PHY_DX8SL3IOCR_DXTXM_MASK | DDR_PHY_DX8SL3IOCR_DXRXM_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL3IOCR_RESERVED_31_SHIFT - | 0x00000007U << DDR_PHY_DX8SL3IOCR_DXDACRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3IOCR_DXVREFIOM_SHIFT - | 0x00000002U << DDR_PHY_DX8SL3IOCR_DXIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3IOCR_DXTXM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL3IOCR_DXRXM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL3IOCR_OFFSET ,0xFFFFFFFFU ,0x70800000U); - /*############################################################################################################################ */ - - /*Register : DX8SL4OSC @ 0XFD081500</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL4OSC_RESERVED_31_30 0x0 - - Enable Clock Gating for DX ddr_clk - PSU_DDR_PHY_DX8SL4OSC_GATEDXRDCLK 0x2 - - Enable Clock Gating for DX ctl_rd_clk - PSU_DDR_PHY_DX8SL4OSC_GATEDXDDRCLK 0x2 - - Enable Clock Gating for DX ctl_clk - PSU_DDR_PHY_DX8SL4OSC_GATEDXCTLCLK 0x2 - - Selects the level to which clocks will be stalled when clock gating is enabled. - PSU_DDR_PHY_DX8SL4OSC_CLKLEVEL 0x0 - - Loopback Mode - PSU_DDR_PHY_DX8SL4OSC_LBMODE 0x0 - - Load GSDQS LCDL with 2x the calibrated GSDQSPRD value - PSU_DDR_PHY_DX8SL4OSC_LBGSDQS 0x0 - - Loopback DQS Gating - PSU_DDR_PHY_DX8SL4OSC_LBGDQS 0x0 - - Loopback DQS Shift - PSU_DDR_PHY_DX8SL4OSC_LBDQSS 0x0 - - PHY High-Speed Reset - PSU_DDR_PHY_DX8SL4OSC_PHYHRST 0x1 - - PHY FIFO Reset - PSU_DDR_PHY_DX8SL4OSC_PHYFRST 0x1 - - Delay Line Test Start - PSU_DDR_PHY_DX8SL4OSC_DLTST 0x0 - - Delay Line Test Mode - PSU_DDR_PHY_DX8SL4OSC_DLTMODE 0x0 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8SL4OSC_RESERVED_12_11 0x3 - - Oscillator Mode Write-Data Delay Line Select - PSU_DDR_PHY_DX8SL4OSC_OSCWDDL 0x3 - - Reserved. Caution, do not write to this register field. - PSU_DDR_PHY_DX8SL4OSC_RESERVED_8_7 0x3 - - Oscillator Mode Write-Leveling Delay Line Select - PSU_DDR_PHY_DX8SL4OSC_OSCWDL 0x3 - - Oscillator Mode Division - PSU_DDR_PHY_DX8SL4OSC_OSCDIV 0xf - - Oscillator Enable - PSU_DDR_PHY_DX8SL4OSC_OSCEN 0x0 - - DATX8 0-1 Oscillator, Delay Line Test, PHY FIFO and High Speed Reset, Loopback, and Gated Clock Control Register - (OFFSET, MASK, VALUE) (0XFD081500, 0xFFFFFFFFU ,0x2A019FFEU) - RegMask = (DDR_PHY_DX8SL4OSC_RESERVED_31_30_MASK | DDR_PHY_DX8SL4OSC_GATEDXRDCLK_MASK | DDR_PHY_DX8SL4OSC_GATEDXDDRCLK_MASK | DDR_PHY_DX8SL4OSC_GATEDXCTLCLK_MASK | DDR_PHY_DX8SL4OSC_CLKLEVEL_MASK | DDR_PHY_DX8SL4OSC_LBMODE_MASK | DDR_PHY_DX8SL4OSC_LBGSDQS_MASK | DDR_PHY_DX8SL4OSC_LBGDQS_MASK | DDR_PHY_DX8SL4OSC_LBDQSS_MASK | DDR_PHY_DX8SL4OSC_PHYHRST_MASK | DDR_PHY_DX8SL4OSC_PHYFRST_MASK | DDR_PHY_DX8SL4OSC_DLTST_MASK | DDR_PHY_DX8SL4OSC_DLTMODE_MASK | DDR_PHY_DX8SL4OSC_RESERVED_12_11_MASK | DDR_PHY_DX8SL4OSC_OSCWDDL_MASK | DDR_PHY_DX8SL4OSC_RESERVED_8_7_MASK | DDR_PHY_DX8SL4OSC_OSCWDL_MASK | DDR_PHY_DX8SL4OSC_OSCDIV_MASK | DDR_PHY_DX8SL4OSC_OSCEN_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL4OSC_RESERVED_31_30_SHIFT - | 0x00000002U << DDR_PHY_DX8SL4OSC_GATEDXRDCLK_SHIFT - | 0x00000002U << DDR_PHY_DX8SL4OSC_GATEDXDDRCLK_SHIFT - | 0x00000002U << DDR_PHY_DX8SL4OSC_GATEDXCTLCLK_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4OSC_CLKLEVEL_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4OSC_LBMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4OSC_LBGSDQS_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4OSC_LBGDQS_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4OSC_LBDQSS_SHIFT - | 0x00000001U << DDR_PHY_DX8SL4OSC_PHYHRST_SHIFT - | 0x00000001U << DDR_PHY_DX8SL4OSC_PHYFRST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4OSC_DLTST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4OSC_DLTMODE_SHIFT - | 0x00000003U << DDR_PHY_DX8SL4OSC_RESERVED_12_11_SHIFT - | 0x00000003U << DDR_PHY_DX8SL4OSC_OSCWDDL_SHIFT - | 0x00000003U << DDR_PHY_DX8SL4OSC_RESERVED_8_7_SHIFT - | 0x00000003U << DDR_PHY_DX8SL4OSC_OSCWDL_SHIFT - | 0x0000000FU << DDR_PHY_DX8SL4OSC_OSCDIV_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4OSC_OSCEN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL4OSC_OFFSET ,0xFFFFFFFFU ,0x2A019FFEU); - /*############################################################################################################################ */ - - /*Register : DX8SL4DQSCTL @ 0XFD08151C</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25 0x0 - - Read Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SL4DQSCTL_RRRMODE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22 0x0 - - Write Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SL4DQSCTL_WRRMODE 0x1 - - DQS Gate Extension - PSU_DDR_PHY_DX8SL4DQSCTL_DQSGX 0x0 - - Low Power PLL Power Down - PSU_DDR_PHY_DX8SL4DQSCTL_LPPLLPD 0x1 - - Low Power I/O Power Down - PSU_DDR_PHY_DX8SL4DQSCTL_LPIOPD 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15 0x0 - - QS Counter Enable - PSU_DDR_PHY_DX8SL4DQSCTL_QSCNTEN 0x1 - - Unused DQ I/O Mode - PSU_DDR_PHY_DX8SL4DQSCTL_UDQIOM 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10 0x0 - - Data Slew Rate - PSU_DDR_PHY_DX8SL4DQSCTL_DXSR 0x3 - - DQS_N Resistor - PSU_DDR_PHY_DX8SL4DQSCTL_DQSNRES 0x0 - - DQS Resistor - PSU_DDR_PHY_DX8SL4DQSCTL_DQSRES 0x0 - - DATX8 0-1 DQS Control Register - (OFFSET, MASK, VALUE) (0XFD08151C, 0xFFFFFFFFU ,0x01264300U) - RegMask = (DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25_MASK | DDR_PHY_DX8SL4DQSCTL_RRRMODE_MASK | DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22_MASK | DDR_PHY_DX8SL4DQSCTL_WRRMODE_MASK | DDR_PHY_DX8SL4DQSCTL_DQSGX_MASK | DDR_PHY_DX8SL4DQSCTL_LPPLLPD_MASK | DDR_PHY_DX8SL4DQSCTL_LPIOPD_MASK | DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15_MASK | DDR_PHY_DX8SL4DQSCTL_QSCNTEN_MASK | DDR_PHY_DX8SL4DQSCTL_UDQIOM_MASK | DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10_MASK | DDR_PHY_DX8SL4DQSCTL_DXSR_MASK | DDR_PHY_DX8SL4DQSCTL_DQSNRES_MASK | DDR_PHY_DX8SL4DQSCTL_DQSRES_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25_SHIFT - | 0x00000001U << DDR_PHY_DX8SL4DQSCTL_RRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22_SHIFT - | 0x00000001U << DDR_PHY_DX8SL4DQSCTL_WRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DQSCTL_DQSGX_SHIFT - | 0x00000001U << DDR_PHY_DX8SL4DQSCTL_LPPLLPD_SHIFT - | 0x00000001U << DDR_PHY_DX8SL4DQSCTL_LPIOPD_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15_SHIFT - | 0x00000001U << DDR_PHY_DX8SL4DQSCTL_QSCNTEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DQSCTL_UDQIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10_SHIFT - | 0x00000003U << DDR_PHY_DX8SL4DQSCTL_DXSR_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DQSCTL_DQSNRES_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DQSCTL_DQSRES_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL4DQSCTL_OFFSET ,0xFFFFFFFFU ,0x01264300U); - /*############################################################################################################################ */ - - /*Register : DX8SL4DXCTL2 @ 0XFD08152C</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24 0x0 - - Configurable Read Data Enable - PSU_DDR_PHY_DX8SL4DXCTL2_CRDEN 0x0 - - OX Extension during Post-amble - PSU_DDR_PHY_DX8SL4DXCTL2_POSOEX 0x0 - - OE Extension during Pre-amble - PSU_DDR_PHY_DX8SL4DXCTL2_PREOEX 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_17 0x0 - - I/O Assisted Gate Select - PSU_DDR_PHY_DX8SL4DXCTL2_IOAG 0x0 - - I/O Loopback Select - PSU_DDR_PHY_DX8SL4DXCTL2_IOLB 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13 0x0 - - Low Power Wakeup Threshold - PSU_DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH 0xc - - Read Data Bus Inversion Enable - PSU_DDR_PHY_DX8SL4DXCTL2_RDBI 0x0 - - Write Data Bus Inversion Enable - PSU_DDR_PHY_DX8SL4DXCTL2_WDBI 0x0 - - PUB Read FIFO Bypass - PSU_DDR_PHY_DX8SL4DXCTL2_PRFBYP 0x0 - - DATX8 Receive FIFO Read Mode - PSU_DDR_PHY_DX8SL4DXCTL2_RDMODE 0x0 - - Disables the Read FIFO Reset - PSU_DDR_PHY_DX8SL4DXCTL2_DISRST 0x0 - - Read DQS Gate I/O Loopback - PSU_DDR_PHY_DX8SL4DXCTL2_DQSGLB 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL4DXCTL2_RESERVED_0 0x0 - - DATX8 0-1 DX Control Register 2 - (OFFSET, MASK, VALUE) (0XFD08152C, 0xFFFFFFFFU ,0x00041800U) - RegMask = (DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24_MASK | DDR_PHY_DX8SL4DXCTL2_CRDEN_MASK | DDR_PHY_DX8SL4DXCTL2_POSOEX_MASK | DDR_PHY_DX8SL4DXCTL2_PREOEX_MASK | DDR_PHY_DX8SL4DXCTL2_RESERVED_17_MASK | DDR_PHY_DX8SL4DXCTL2_IOAG_MASK | DDR_PHY_DX8SL4DXCTL2_IOLB_MASK | DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13_MASK | DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH_MASK | DDR_PHY_DX8SL4DXCTL2_RDBI_MASK | DDR_PHY_DX8SL4DXCTL2_WDBI_MASK | DDR_PHY_DX8SL4DXCTL2_PRFBYP_MASK | DDR_PHY_DX8SL4DXCTL2_RDMODE_MASK | DDR_PHY_DX8SL4DXCTL2_DISRST_MASK | DDR_PHY_DX8SL4DXCTL2_DQSGLB_MASK | DDR_PHY_DX8SL4DXCTL2_RESERVED_0_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_CRDEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_POSOEX_SHIFT - | 0x00000001U << DDR_PHY_DX8SL4DXCTL2_PREOEX_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_RESERVED_17_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_IOAG_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_IOLB_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13_SHIFT - | 0x0000000CU << DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_RDBI_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_WDBI_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_PRFBYP_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_RDMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_DISRST_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_DQSGLB_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4DXCTL2_RESERVED_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL4DXCTL2_OFFSET ,0xFFFFFFFFU ,0x00041800U); - /*############################################################################################################################ */ - - /*Register : DX8SL4IOCR @ 0XFD081530</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SL4IOCR_RESERVED_31 0x0 - - PVREF_DAC REFSEL range select - PSU_DDR_PHY_DX8SL4IOCR_DXDACRANGE 0x7 - - IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring - PSU_DDR_PHY_DX8SL4IOCR_DXVREFIOM 0x0 - - DX IO Mode - PSU_DDR_PHY_DX8SL4IOCR_DXIOM 0x2 - - DX IO Transmitter Mode - PSU_DDR_PHY_DX8SL4IOCR_DXTXM 0x0 - - DX IO Receiver Mode - PSU_DDR_PHY_DX8SL4IOCR_DXRXM 0x0 - - DATX8 0-1 I/O Configuration Register - (OFFSET, MASK, VALUE) (0XFD081530, 0xFFFFFFFFU ,0x70800000U) - RegMask = (DDR_PHY_DX8SL4IOCR_RESERVED_31_MASK | DDR_PHY_DX8SL4IOCR_DXDACRANGE_MASK | DDR_PHY_DX8SL4IOCR_DXVREFIOM_MASK | DDR_PHY_DX8SL4IOCR_DXIOM_MASK | DDR_PHY_DX8SL4IOCR_DXTXM_MASK | DDR_PHY_DX8SL4IOCR_DXRXM_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SL4IOCR_RESERVED_31_SHIFT - | 0x00000007U << DDR_PHY_DX8SL4IOCR_DXDACRANGE_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4IOCR_DXVREFIOM_SHIFT - | 0x00000002U << DDR_PHY_DX8SL4IOCR_DXIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4IOCR_DXTXM_SHIFT - | 0x00000000U << DDR_PHY_DX8SL4IOCR_DXRXM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SL4IOCR_OFFSET ,0xFFFFFFFFU ,0x70800000U); - /*############################################################################################################################ */ - - /*Register : DX8SLbDQSCTL @ 0XFD0817DC</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25 0x0 - - Read Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SLBDQSCTL_RRRMODE 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22 0x0 - - Write Path Rise-to-Rise Mode - PSU_DDR_PHY_DX8SLBDQSCTL_WRRMODE 0x1 - - DQS Gate Extension - PSU_DDR_PHY_DX8SLBDQSCTL_DQSGX 0x0 - - Low Power PLL Power Down - PSU_DDR_PHY_DX8SLBDQSCTL_LPPLLPD 0x1 - - Low Power I/O Power Down - PSU_DDR_PHY_DX8SLBDQSCTL_LPIOPD 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15 0x0 - - QS Counter Enable - PSU_DDR_PHY_DX8SLBDQSCTL_QSCNTEN 0x1 - - Unused DQ I/O Mode - PSU_DDR_PHY_DX8SLBDQSCTL_UDQIOM 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10 0x0 - - Data Slew Rate - PSU_DDR_PHY_DX8SLBDQSCTL_DXSR 0x3 - - DQS# Resistor - PSU_DDR_PHY_DX8SLBDQSCTL_DQSNRES 0xc - - DQS Resistor - PSU_DDR_PHY_DX8SLBDQSCTL_DQSRES 0x4 - - DATX8 0-8 DQS Control Register - (OFFSET, MASK, VALUE) (0XFD0817DC, 0xFFFFFFFFU ,0x012643C4U) - RegMask = (DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25_MASK | DDR_PHY_DX8SLBDQSCTL_RRRMODE_MASK | DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22_MASK | DDR_PHY_DX8SLBDQSCTL_WRRMODE_MASK | DDR_PHY_DX8SLBDQSCTL_DQSGX_MASK | DDR_PHY_DX8SLBDQSCTL_LPPLLPD_MASK | DDR_PHY_DX8SLBDQSCTL_LPIOPD_MASK | DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15_MASK | DDR_PHY_DX8SLBDQSCTL_QSCNTEN_MASK | DDR_PHY_DX8SLBDQSCTL_UDQIOM_MASK | DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10_MASK | DDR_PHY_DX8SLBDQSCTL_DXSR_MASK | DDR_PHY_DX8SLBDQSCTL_DQSNRES_MASK | DDR_PHY_DX8SLBDQSCTL_DQSRES_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25_SHIFT - | 0x00000001U << DDR_PHY_DX8SLBDQSCTL_RRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22_SHIFT - | 0x00000001U << DDR_PHY_DX8SLBDQSCTL_WRRMODE_SHIFT - | 0x00000000U << DDR_PHY_DX8SLBDQSCTL_DQSGX_SHIFT - | 0x00000001U << DDR_PHY_DX8SLBDQSCTL_LPPLLPD_SHIFT - | 0x00000001U << DDR_PHY_DX8SLBDQSCTL_LPIOPD_SHIFT - | 0x00000000U << DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15_SHIFT - | 0x00000001U << DDR_PHY_DX8SLBDQSCTL_QSCNTEN_SHIFT - | 0x00000000U << DDR_PHY_DX8SLBDQSCTL_UDQIOM_SHIFT - | 0x00000000U << DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10_SHIFT - | 0x00000003U << DDR_PHY_DX8SLBDQSCTL_DXSR_SHIFT - | 0x0000000CU << DDR_PHY_DX8SLBDQSCTL_DQSNRES_SHIFT - | 0x00000004U << DDR_PHY_DX8SLBDQSCTL_DQSRES_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_DX8SLBDQSCTL_OFFSET ,0xFFFFFFFFU ,0x012643C4U); - /*############################################################################################################################ */ - - /*Register : PIR @ 0XFD080004</p> - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_PIR_RESERVED_31 0x0 - - Impedance Calibration Bypass - PSU_DDR_PHY_PIR_ZCALBYP 0x0 - - Digital Delay Line (DDL) Calibration Pause - PSU_DDR_PHY_PIR_DCALPSE 0x0 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_PIR_RESERVED_28_21 0x0 - - Write DQS2DQ Training - PSU_DDR_PHY_PIR_DQS2DQ 0x0 - - RDIMM Initialization - PSU_DDR_PHY_PIR_RDIMMINIT 0x0 - - Controller DRAM Initialization - PSU_DDR_PHY_PIR_CTLDINIT 0x1 - - VREF Training - PSU_DDR_PHY_PIR_VREF 0x0 - - Static Read Training - PSU_DDR_PHY_PIR_SRD 0x0 - - Write Data Eye Training - PSU_DDR_PHY_PIR_WREYE 0x0 - - Read Data Eye Training - PSU_DDR_PHY_PIR_RDEYE 0x0 - - Write Data Bit Deskew - PSU_DDR_PHY_PIR_WRDSKW 0x0 - - Read Data Bit Deskew - PSU_DDR_PHY_PIR_RDDSKW 0x0 - - Write Leveling Adjust - PSU_DDR_PHY_PIR_WLADJ 0x0 - - Read DQS Gate Training - PSU_DDR_PHY_PIR_QSGATE 0x0 - - Write Leveling - PSU_DDR_PHY_PIR_WL 0x0 - - DRAM Initialization - PSU_DDR_PHY_PIR_DRAMINIT 0x0 - - DRAM Reset (DDR3/DDR4/LPDDR4 Only) - PSU_DDR_PHY_PIR_DRAMRST 0x0 - - PHY Reset - PSU_DDR_PHY_PIR_PHYRST 0x1 - - Digital Delay Line (DDL) Calibration - PSU_DDR_PHY_PIR_DCAL 0x1 - - PLL Initialiazation - PSU_DDR_PHY_PIR_PLLINIT 0x1 - - Reserved. Return zeroes on reads. - PSU_DDR_PHY_PIR_RESERVED_3 0x0 - - CA Training - PSU_DDR_PHY_PIR_CA 0x0 - - Impedance Calibration - PSU_DDR_PHY_PIR_ZCAL 0x1 - - Initialization Trigger - PSU_DDR_PHY_PIR_INIT 0x1 - - PHY Initialization Register - (OFFSET, MASK, VALUE) (0XFD080004, 0xFFFFFFFFU ,0x00040073U) - RegMask = (DDR_PHY_PIR_RESERVED_31_MASK | DDR_PHY_PIR_ZCALBYP_MASK | DDR_PHY_PIR_DCALPSE_MASK | DDR_PHY_PIR_RESERVED_28_21_MASK | DDR_PHY_PIR_DQS2DQ_MASK | DDR_PHY_PIR_RDIMMINIT_MASK | DDR_PHY_PIR_CTLDINIT_MASK | DDR_PHY_PIR_VREF_MASK | DDR_PHY_PIR_SRD_MASK | DDR_PHY_PIR_WREYE_MASK | DDR_PHY_PIR_RDEYE_MASK | DDR_PHY_PIR_WRDSKW_MASK | DDR_PHY_PIR_RDDSKW_MASK | DDR_PHY_PIR_WLADJ_MASK | DDR_PHY_PIR_QSGATE_MASK | DDR_PHY_PIR_WL_MASK | DDR_PHY_PIR_DRAMINIT_MASK | DDR_PHY_PIR_DRAMRST_MASK | DDR_PHY_PIR_PHYRST_MASK | DDR_PHY_PIR_DCAL_MASK | DDR_PHY_PIR_PLLINIT_MASK | DDR_PHY_PIR_RESERVED_3_MASK | DDR_PHY_PIR_CA_MASK | DDR_PHY_PIR_ZCAL_MASK | DDR_PHY_PIR_INIT_MASK | 0 ); - - RegVal = ((0x00000000U << DDR_PHY_PIR_RESERVED_31_SHIFT - | 0x00000000U << DDR_PHY_PIR_ZCALBYP_SHIFT - | 0x00000000U << DDR_PHY_PIR_DCALPSE_SHIFT - | 0x00000000U << DDR_PHY_PIR_RESERVED_28_21_SHIFT - | 0x00000000U << DDR_PHY_PIR_DQS2DQ_SHIFT - | 0x00000000U << DDR_PHY_PIR_RDIMMINIT_SHIFT - | 0x00000001U << DDR_PHY_PIR_CTLDINIT_SHIFT - | 0x00000000U << DDR_PHY_PIR_VREF_SHIFT - | 0x00000000U << DDR_PHY_PIR_SRD_SHIFT - | 0x00000000U << DDR_PHY_PIR_WREYE_SHIFT - | 0x00000000U << DDR_PHY_PIR_RDEYE_SHIFT - | 0x00000000U << DDR_PHY_PIR_WRDSKW_SHIFT - | 0x00000000U << DDR_PHY_PIR_RDDSKW_SHIFT - | 0x00000000U << DDR_PHY_PIR_WLADJ_SHIFT - | 0x00000000U << DDR_PHY_PIR_QSGATE_SHIFT - | 0x00000000U << DDR_PHY_PIR_WL_SHIFT - | 0x00000000U << DDR_PHY_PIR_DRAMINIT_SHIFT - | 0x00000000U << DDR_PHY_PIR_DRAMRST_SHIFT - | 0x00000001U << DDR_PHY_PIR_PHYRST_SHIFT - | 0x00000001U << DDR_PHY_PIR_DCAL_SHIFT - | 0x00000001U << DDR_PHY_PIR_PLLINIT_SHIFT - | 0x00000000U << DDR_PHY_PIR_RESERVED_3_SHIFT - | 0x00000000U << DDR_PHY_PIR_CA_SHIFT - | 0x00000001U << DDR_PHY_PIR_ZCAL_SHIFT - | 0x00000001U << DDR_PHY_PIR_INIT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DDR_PHY_PIR_OFFSET ,0xFFFFFFFFU ,0x00040073U); - /*############################################################################################################################ */ - - - return 1; -} -unsigned long psu_mio_init_data() { - // : MIO PROGRAMMING - /*Register : MIO_PIN_0 @ 0XFF180000</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_sclk_out- (QSPI Clock) - PSU_IOU_SLCR_MIO_PIN_0_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_0_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[0]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[0]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_0_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[0]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[0]- (GPIO bank 0) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Cloc - ) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, trace_ - lk- (Trace Port Clock) - PSU_IOU_SLCR_MIO_PIN_0_L3_SEL 0 - - Configures MIO Pin 0 peripheral interface mapping. S - (OFFSET, MASK, VALUE) (0XFF180000, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_0_L0_SEL_MASK | IOU_SLCR_MIO_PIN_0_L1_SEL_MASK | IOU_SLCR_MIO_PIN_0_L2_SEL_MASK | IOU_SLCR_MIO_PIN_0_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_0_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_0_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_0_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_0_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_0_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_1 @ 0XFF180004</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_mi1- (QSPI Databus) 1= qspi, Output, qspi_so_mo1- (QSPI Data - us) - PSU_IOU_SLCR_MIO_PIN_1_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_1_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[1]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[1]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_1_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[1]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[1]- (GPIO bank 0) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc3, Output, ttc3_wave_o - t- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, trace_ctl- (Trace Port Control - Signal) - PSU_IOU_SLCR_MIO_PIN_1_L3_SEL 0 - - Configures MIO Pin 1 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180004, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_1_L0_SEL_MASK | IOU_SLCR_MIO_PIN_1_L1_SEL_MASK | IOU_SLCR_MIO_PIN_1_L2_SEL_MASK | IOU_SLCR_MIO_PIN_1_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_1_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_1_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_1_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_1_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_1_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_2 @ 0XFF180008</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi2- (QSPI Databus) 1= qspi, Output, qspi_mo2- (QSPI Databus) - PSU_IOU_SLCR_MIO_PIN_2_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_2_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[2]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[2]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_2_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[2]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[2]- (GPIO bank 0) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc2, Input, ttc2_clk_in - (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[0]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_2_L3_SEL 0 - - Configures MIO Pin 2 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180008, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_2_L0_SEL_MASK | IOU_SLCR_MIO_PIN_2_L1_SEL_MASK | IOU_SLCR_MIO_PIN_2_L2_SEL_MASK | IOU_SLCR_MIO_PIN_2_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_2_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_2_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_2_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_2_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_2_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_3 @ 0XFF18000C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi3- (QSPI Databus) 1= qspi, Output, qspi_mo3- (QSPI Databus) - PSU_IOU_SLCR_MIO_PIN_3_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_3_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[3]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[3]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_3_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[3]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[3]- (GPIO bank 0) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[0 - - (SPI Master Selects) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial - output) 7= trace, Output, tracedq[1]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_3_L3_SEL 0 - - Configures MIO Pin 3 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18000C, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_3_L0_SEL_MASK | IOU_SLCR_MIO_PIN_3_L1_SEL_MASK | IOU_SLCR_MIO_PIN_3_L2_SEL_MASK | IOU_SLCR_MIO_PIN_3_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_3_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_3_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_3_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_3_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_3_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_4 @ 0XFF180010</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_mo_mo0- (QSPI Databus) 1= qspi, Input, qspi_si_mi0- (QSPI Data - us) - PSU_IOU_SLCR_MIO_PIN_4_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_4_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[4]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[4]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_4_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[4]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[4]- (GPIO bank 0) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_s - - (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, - utput, tracedq[2]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_4_L3_SEL 0 - - Configures MIO Pin 4 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180010, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_4_L0_SEL_MASK | IOU_SLCR_MIO_PIN_4_L1_SEL_MASK | IOU_SLCR_MIO_PIN_4_L2_SEL_MASK | IOU_SLCR_MIO_PIN_4_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_4_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_4_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_4_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_4_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_4_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_5 @ 0XFF180014</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_n_ss_out- (QSPI Slave Select) - PSU_IOU_SLCR_MIO_PIN_5_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_5_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[5]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[5]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_5_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[5]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[5]- (GPIO bank 0) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, spi0 - si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7 - trace, Output, tracedq[3]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_5_L3_SEL 0 - - Configures MIO Pin 5 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180014, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_5_L0_SEL_MASK | IOU_SLCR_MIO_PIN_5_L1_SEL_MASK | IOU_SLCR_MIO_PIN_5_L2_SEL_MASK | IOU_SLCR_MIO_PIN_5_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_5_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_5_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_5_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_5_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_5_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_6 @ 0XFF180018</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_clk_for_lpbk- (QSPI Clock to be fed-back) - PSU_IOU_SLCR_MIO_PIN_6_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_6_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[6]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[6]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_6_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[6]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[6]- (GPIO bank 0) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, spi1 - sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, - Output, tracedq[4]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_6_L3_SEL 0 - - Configures MIO Pin 6 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180018, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_6_L0_SEL_MASK | IOU_SLCR_MIO_PIN_6_L1_SEL_MASK | IOU_SLCR_MIO_PIN_6_L2_SEL_MASK | IOU_SLCR_MIO_PIN_6_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_6_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_6_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_6_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_6_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_6_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_7 @ 0XFF18001C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_n_ss_out_upper- (QSPI Slave Select upper) - PSU_IOU_SLCR_MIO_PIN_7_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_7_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[7]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[7]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_7_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[7]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[7]- (GPIO bank 0) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= - tc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, - racedq[5]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_7_L3_SEL 0 - - Configures MIO Pin 7 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18001C, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_7_L0_SEL_MASK | IOU_SLCR_MIO_PIN_7_L1_SEL_MASK | IOU_SLCR_MIO_PIN_7_L2_SEL_MASK | IOU_SLCR_MIO_PIN_7_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_7_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_7_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_7_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_7_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_7_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_8 @ 0XFF180020</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[0]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe - [0]- (QSPI Upper Databus) - PSU_IOU_SLCR_MIO_PIN_8_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_8_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[8]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[8]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_8_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[8]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[8]- (GPIO bank 0) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= ttc - , Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[6]- (Tr - ce Port Databus) - PSU_IOU_SLCR_MIO_PIN_8_L3_SEL 0 - - Configures MIO Pin 8 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180020, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_8_L0_SEL_MASK | IOU_SLCR_MIO_PIN_8_L1_SEL_MASK | IOU_SLCR_MIO_PIN_8_L2_SEL_MASK | IOU_SLCR_MIO_PIN_8_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_8_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_8_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_8_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_8_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_8_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_9 @ 0XFF180024</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[1]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe - [1]- (QSPI Upper Databus) - PSU_IOU_SLCR_MIO_PIN_9_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[1]- (NAND chip enable) - PSU_IOU_SLCR_MIO_PIN_9_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[9]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[9]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_9_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[9]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[9]- (GPIO bank 0) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1, - utput, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (U - RT receiver serial input) 7= trace, Output, tracedq[7]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_9_L3_SEL 0 - - Configures MIO Pin 9 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180024, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_9_L0_SEL_MASK | IOU_SLCR_MIO_PIN_9_L1_SEL_MASK | IOU_SLCR_MIO_PIN_9_L2_SEL_MASK | IOU_SLCR_MIO_PIN_9_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_9_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_9_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_9_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_9_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_9_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_10 @ 0XFF180028</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[2]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe - [2]- (QSPI Upper Databus) - PSU_IOU_SLCR_MIO_PIN_10_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[0]- (NAND Ready/Busy) - PSU_IOU_SLCR_MIO_PIN_10_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[10]- (Test Scan Port) = test_scan, Out - ut, test_scan_out[10]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_10_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[10]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[10]- (GPIO bank 0) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_ - o- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outp - t, tracedq[8]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_10_L3_SEL 0 - - Configures MIO Pin 10 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180028, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_10_L0_SEL_MASK | IOU_SLCR_MIO_PIN_10_L1_SEL_MASK | IOU_SLCR_MIO_PIN_10_L2_SEL_MASK | IOU_SLCR_MIO_PIN_10_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_10_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_10_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_10_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_10_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_10_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_11 @ 0XFF18002C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[3]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe - [3]- (QSPI Upper Databus) - PSU_IOU_SLCR_MIO_PIN_11_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[1]- (NAND Ready/Busy) - PSU_IOU_SLCR_MIO_PIN_11_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[11]- (Test Scan Port) = test_scan, Out - ut, test_scan_out[11]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_11_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[11]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[11]- (GPIO bank 0) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s - i1_si- (MOSI signal) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o - tput) 7= trace, Output, tracedq[9]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_11_L3_SEL 0 - - Configures MIO Pin 11 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18002C, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_11_L0_SEL_MASK | IOU_SLCR_MIO_PIN_11_L1_SEL_MASK | IOU_SLCR_MIO_PIN_11_L2_SEL_MASK | IOU_SLCR_MIO_PIN_11_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_11_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_11_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_11_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_11_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_11_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_12 @ 0XFF180030</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_sclk_out_upper- (QSPI Upper Clock) - PSU_IOU_SLCR_MIO_PIN_12_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dqs_in- (NAND Strobe) 1= nand, Output, nfc_dqs_out- (NAND Strobe - - PSU_IOU_SLCR_MIO_PIN_12_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[12]- (Test Scan Port) = test_scan, Out - ut, test_scan_out[12]- (Test Scan Port) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_12_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[12]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[12]- (GPIO bank 0) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Cl - ck) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, trac - dq[10]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_12_L3_SEL 0 - - Configures MIO Pin 12 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180030, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_12_L0_SEL_MASK | IOU_SLCR_MIO_PIN_12_L1_SEL_MASK | IOU_SLCR_MIO_PIN_12_L2_SEL_MASK | IOU_SLCR_MIO_PIN_12_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_12_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_12_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_12_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_12_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_12_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_13 @ 0XFF180034</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_13_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[0]- (NAND chip enable) - PSU_IOU_SLCR_MIO_PIN_13_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]- (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[13]- (Test Scan Port) = test_scan, Output, test_scan_out[13]- (Test Scan Port - 3= Not Used - PSU_IOU_SLCR_MIO_PIN_13_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[13]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[13]- (GPIO bank 0) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave - out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, tracedq[11]- (Trace Port Dat - bus) - PSU_IOU_SLCR_MIO_PIN_13_L3_SEL 0 - - Configures MIO Pin 13 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180034, 0x000000FEU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_PIN_13_L0_SEL_MASK | IOU_SLCR_MIO_PIN_13_L1_SEL_MASK | IOU_SLCR_MIO_PIN_13_L2_SEL_MASK | IOU_SLCR_MIO_PIN_13_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_13_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_13_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_13_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_13_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_13_OFFSET ,0x000000FEU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_14 @ 0XFF180038</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_14_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_cle- (NAND Command Latch Enable) - PSU_IOU_SLCR_MIO_PIN_14_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]- (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[14]- (Test Scan Port) = test_scan, Output, test_scan_out[14]- (Test Scan Port - 3= Not Used - PSU_IOU_SLCR_MIO_PIN_14_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[14]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[14]- (GPIO bank 0) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc0, Input, ttc0_clk_ - n- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_14_L3_SEL 2 - - Configures MIO Pin 14 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180038, 0x000000FEU ,0x00000040U) - RegMask = (IOU_SLCR_MIO_PIN_14_L0_SEL_MASK | IOU_SLCR_MIO_PIN_14_L1_SEL_MASK | IOU_SLCR_MIO_PIN_14_L2_SEL_MASK | IOU_SLCR_MIO_PIN_14_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_14_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_14_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_14_L2_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_14_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_14_OFFSET ,0x000000FEU ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_15 @ 0XFF18003C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_15_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ale- (NAND Address Latch Enable) - PSU_IOU_SLCR_MIO_PIN_15_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]- (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[15]- (Test Scan Port) = test_scan, Output, test_scan_out[15]- (Test Scan Port - 3= Not Used - PSU_IOU_SLCR_MIO_PIN_15_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[15]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[15]- (GPIO bank 0) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out - 0]- (SPI Master Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter seri - l output) 7= trace, Output, tracedq[13]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_15_L3_SEL 2 - - Configures MIO Pin 15 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18003C, 0x000000FEU ,0x00000040U) - RegMask = (IOU_SLCR_MIO_PIN_15_L0_SEL_MASK | IOU_SLCR_MIO_PIN_15_L1_SEL_MASK | IOU_SLCR_MIO_PIN_15_L2_SEL_MASK | IOU_SLCR_MIO_PIN_15_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_15_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_15_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_15_L2_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_15_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_15_OFFSET ,0x000000FEU ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_16 @ 0XFF180040</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_16_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[0]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[0]- (NAND - ata Bus) - PSU_IOU_SLCR_MIO_PIN_16_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]- (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[16]- (Test Scan Port) = test_scan, Output, test_scan_out[16]- (Test Scan Port - 3= Not Used - PSU_IOU_SLCR_MIO_PIN_16_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[16]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[16]- (GPIO bank 0) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0 - so- (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace - Output, tracedq[14]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_16_L3_SEL 2 - - Configures MIO Pin 16 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180040, 0x000000FEU ,0x00000040U) - RegMask = (IOU_SLCR_MIO_PIN_16_L0_SEL_MASK | IOU_SLCR_MIO_PIN_16_L1_SEL_MASK | IOU_SLCR_MIO_PIN_16_L2_SEL_MASK | IOU_SLCR_MIO_PIN_16_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_16_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_16_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_16_L2_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_16_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_16_OFFSET ,0x000000FEU ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_17 @ 0XFF180044</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_17_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[1]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[1]- (NAND - ata Bus) - PSU_IOU_SLCR_MIO_PIN_17_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]- (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[17]- (Test Scan Port) = test_scan, Output, test_scan_out[17]- (Test Scan Port - 3= Not Used - PSU_IOU_SLCR_MIO_PIN_17_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[17]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[17]- (GPIO bank 0) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, sp - 0_si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) - 7= trace, Output, tracedq[15]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_17_L3_SEL 2 - - Configures MIO Pin 17 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180044, 0x000000FEU ,0x00000040U) - RegMask = (IOU_SLCR_MIO_PIN_17_L0_SEL_MASK | IOU_SLCR_MIO_PIN_17_L1_SEL_MASK | IOU_SLCR_MIO_PIN_17_L2_SEL_MASK | IOU_SLCR_MIO_PIN_17_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_17_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_17_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_17_L2_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_17_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_17_OFFSET ,0x000000FEU ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_18 @ 0XFF180048</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_18_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[2]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[2]- (NAND - ata Bus) - PSU_IOU_SLCR_MIO_PIN_18_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]- (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[18]- (Test Scan Port) = test_scan, Output, test_scan_out[18]- (Test Scan Port - 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper) - PSU_IOU_SLCR_MIO_PIN_18_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[18]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[18]- (GPIO bank 0) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_ - o- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_18_L3_SEL 6 - - Configures MIO Pin 18 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180048, 0x000000FEU ,0x000000C0U) - RegMask = (IOU_SLCR_MIO_PIN_18_L0_SEL_MASK | IOU_SLCR_MIO_PIN_18_L1_SEL_MASK | IOU_SLCR_MIO_PIN_18_L2_SEL_MASK | IOU_SLCR_MIO_PIN_18_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_18_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_18_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_18_L2_SEL_SHIFT - | 0x00000006U << IOU_SLCR_MIO_PIN_18_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_18_OFFSET ,0x000000FEU ,0x000000C0U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_19 @ 0XFF18004C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_19_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[3]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[3]- (NAND - ata Bus) - PSU_IOU_SLCR_MIO_PIN_19_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]- (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[19]- (Test Scan Port) = test_scan, Output, test_scan_out[19]- (Test Scan Port - 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper) - PSU_IOU_SLCR_MIO_PIN_19_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[19]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[19]- (GPIO bank 0) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5 - ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_19_L3_SEL 6 - - Configures MIO Pin 19 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18004C, 0x000000FEU ,0x000000C0U) - RegMask = (IOU_SLCR_MIO_PIN_19_L0_SEL_MASK | IOU_SLCR_MIO_PIN_19_L1_SEL_MASK | IOU_SLCR_MIO_PIN_19_L2_SEL_MASK | IOU_SLCR_MIO_PIN_19_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_19_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_19_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_19_L2_SEL_SHIFT - | 0x00000006U << IOU_SLCR_MIO_PIN_19_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_19_OFFSET ,0x000000FEU ,0x000000C0U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_20 @ 0XFF180050</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_20_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[4]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[4]- (NAND - ata Bus) - PSU_IOU_SLCR_MIO_PIN_20_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]- (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[20]- (Test Scan Port) = test_scan, Output, test_scan_out[20]- (Test Scan Port - 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper) - PSU_IOU_SLCR_MIO_PIN_20_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[20]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[20]- (GPIO bank 0) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= t - c1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_20_L3_SEL 6 - - Configures MIO Pin 20 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180050, 0x000000FEU ,0x000000C0U) - RegMask = (IOU_SLCR_MIO_PIN_20_L0_SEL_MASK | IOU_SLCR_MIO_PIN_20_L1_SEL_MASK | IOU_SLCR_MIO_PIN_20_L2_SEL_MASK | IOU_SLCR_MIO_PIN_20_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_20_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_20_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_20_L2_SEL_SHIFT - | 0x00000006U << IOU_SLCR_MIO_PIN_20_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_20_OFFSET ,0x000000FEU ,0x000000C0U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_21 @ 0XFF180054</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_21_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[5]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[5]- (NAND - ata Bus) - PSU_IOU_SLCR_MIO_PIN_21_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Command Indicator) = sd0, Output, sdio0_cmd_out- (Comman - Indicator) 2= test_scan, Input, test_scan_in[21]- (Test Scan Port) = test_scan, Output, test_scan_out[21]- (Test Scan Port) - = csu, Input, csu_ext_tamper- (CSU Ext Tamper) - PSU_IOU_SLCR_MIO_PIN_21_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[21]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[21]- (GPIO bank 0) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1 - Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- - UART receiver serial input) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_21_L3_SEL 6 - - Configures MIO Pin 21 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180054, 0x000000FEU ,0x000000C0U) - RegMask = (IOU_SLCR_MIO_PIN_21_L0_SEL_MASK | IOU_SLCR_MIO_PIN_21_L1_SEL_MASK | IOU_SLCR_MIO_PIN_21_L2_SEL_MASK | IOU_SLCR_MIO_PIN_21_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_21_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_21_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_21_L2_SEL_SHIFT - | 0x00000006U << IOU_SLCR_MIO_PIN_21_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_21_OFFSET ,0x000000FEU ,0x000000C0U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_22 @ 0XFF180058</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_22_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_we_b- (NAND Write Enable) - PSU_IOU_SLCR_MIO_PIN_22_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out- (SDSDIO clock) 2= test_scan, Input, test_scan_in[22]- - (Test Scan Port) = test_scan, Output, test_scan_out[22]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper) - PSU_IOU_SLCR_MIO_PIN_22_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[22]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[22]- (GPIO bank 0) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, sp - 1_sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not - sed - PSU_IOU_SLCR_MIO_PIN_22_L3_SEL 0 - - Configures MIO Pin 22 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180058, 0x000000FEU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_PIN_22_L0_SEL_MASK | IOU_SLCR_MIO_PIN_22_L1_SEL_MASK | IOU_SLCR_MIO_PIN_22_L2_SEL_MASK | IOU_SLCR_MIO_PIN_22_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_22_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_22_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_22_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_22_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_22_OFFSET ,0x000000FEU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_23 @ 0XFF18005C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_23_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[6]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[6]- (NAND - ata Bus) - PSU_IOU_SLCR_MIO_PIN_23_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow- (SD card bus power) 2= test_scan, Input, test_scan_in - 23]- (Test Scan Port) = test_scan, Output, test_scan_out[23]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper - - PSU_IOU_SLCR_MIO_PIN_23_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[23]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[23]- (GPIO bank 0) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s - i1_si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o - tput) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_23_L3_SEL 0 - - Configures MIO Pin 23 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18005C, 0x000000FEU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_PIN_23_L0_SEL_MASK | IOU_SLCR_MIO_PIN_23_L1_SEL_MASK | IOU_SLCR_MIO_PIN_23_L2_SEL_MASK | IOU_SLCR_MIO_PIN_23_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_23_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_23_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_23_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_23_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_23_OFFSET ,0x000000FEU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_24 @ 0XFF180060</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_24_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[7]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[7]- (NAND - ata Bus) - PSU_IOU_SLCR_MIO_PIN_24_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD card detect from connector) 2= test_scan, Input, test - scan_in[24]- (Test Scan Port) = test_scan, Output, test_scan_out[24]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ex - Tamper) - PSU_IOU_SLCR_MIO_PIN_24_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[24]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[24]- (GPIO bank 0) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= Not Used 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, - Output, ua1_txd- (UART transmitter serial output) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_24_L3_SEL 1 - - Configures MIO Pin 24 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180060, 0x000000FEU ,0x00000020U) - RegMask = (IOU_SLCR_MIO_PIN_24_L0_SEL_MASK | IOU_SLCR_MIO_PIN_24_L1_SEL_MASK | IOU_SLCR_MIO_PIN_24_L2_SEL_MASK | IOU_SLCR_MIO_PIN_24_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_24_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_24_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_24_L2_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_24_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_24_OFFSET ,0x000000FEU ,0x00000020U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_25 @ 0XFF180064</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_25_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_re_n- (NAND Read Enable) - PSU_IOU_SLCR_MIO_PIN_25_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD card write protect from connector) 2= test_scan, Input, - test_scan_in[25]- (Test Scan Port) = test_scan, Output, test_scan_out[25]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (C - U Ext Tamper) - PSU_IOU_SLCR_MIO_PIN_25_L2_SEL 0 - - Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[25]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[25]- (GPIO bank 0) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= Not Used 5= ttc3, Output, ttc3_wave_out- (TTC Waveform - lock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_25_L3_SEL 1 - - Configures MIO Pin 25 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180064, 0x000000FEU ,0x00000020U) - RegMask = (IOU_SLCR_MIO_PIN_25_L0_SEL_MASK | IOU_SLCR_MIO_PIN_25_L1_SEL_MASK | IOU_SLCR_MIO_PIN_25_L2_SEL_MASK | IOU_SLCR_MIO_PIN_25_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_25_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_25_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_25_L2_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_25_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_25_OFFSET ,0x000000FEU ,0x00000020U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_26 @ 0XFF180068</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_tx_clk- (TX RGMII clock) - PSU_IOU_SLCR_MIO_PIN_26_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[1]- (NAND chip enable) - PSU_IOU_SLCR_MIO_PIN_26_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[0]- (PMU GPI) 2= test_scan, Input, test_scan_in[26]- (Test Sc - n Port) = test_scan, Output, test_scan_out[26]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper) - PSU_IOU_SLCR_MIO_PIN_26_L2_SEL 0 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[0]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[0]- (GPIO bank 1) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Clock - 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[4]- - Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_26_L3_SEL 0 - - Configures MIO Pin 26 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180068, 0x000000FEU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_PIN_26_L0_SEL_MASK | IOU_SLCR_MIO_PIN_26_L1_SEL_MASK | IOU_SLCR_MIO_PIN_26_L2_SEL_MASK | IOU_SLCR_MIO_PIN_26_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_26_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_26_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_26_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_26_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_26_OFFSET ,0x000000FEU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_27 @ 0XFF18006C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[0]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_27_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[0]- (NAND Ready/Busy) - PSU_IOU_SLCR_MIO_PIN_27_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[1]- (PMU GPI) 2= test_scan, Input, test_scan_in[27]- (Test Sc - n Port) = test_scan, Output, test_scan_out[27]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Outp - t, dp_aux_data_out- (Dp Aux Data) - PSU_IOU_SLCR_MIO_PIN_27_L2_SEL 3 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[1]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[1]- (GPIO bank 1) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_ - ut- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, tracedq[5]- (Trace Port - atabus) - PSU_IOU_SLCR_MIO_PIN_27_L3_SEL 0 - - Configures MIO Pin 27 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18006C, 0x000000FEU ,0x00000018U) - RegMask = (IOU_SLCR_MIO_PIN_27_L0_SEL_MASK | IOU_SLCR_MIO_PIN_27_L1_SEL_MASK | IOU_SLCR_MIO_PIN_27_L2_SEL_MASK | IOU_SLCR_MIO_PIN_27_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_27_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_27_L1_SEL_SHIFT - | 0x00000003U << IOU_SLCR_MIO_PIN_27_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_27_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_27_OFFSET ,0x000000FEU ,0x00000018U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_28 @ 0XFF180070</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[1]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_28_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[1]- (NAND Ready/Busy) - PSU_IOU_SLCR_MIO_PIN_28_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[2]- (PMU GPI) 2= test_scan, Input, test_scan_in[28]- (Test Sc - n Port) = test_scan, Output, test_scan_out[28]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug) - PSU_IOU_SLCR_MIO_PIN_28_L2_SEL 3 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[2]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[2]- (GPIO bank 1) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc1, Input, ttc1_clk_i - - (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[6]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_28_L3_SEL 0 - - Configures MIO Pin 28 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180070, 0x000000FEU ,0x00000018U) - RegMask = (IOU_SLCR_MIO_PIN_28_L0_SEL_MASK | IOU_SLCR_MIO_PIN_28_L1_SEL_MASK | IOU_SLCR_MIO_PIN_28_L2_SEL_MASK | IOU_SLCR_MIO_PIN_28_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_28_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_28_L1_SEL_SHIFT - | 0x00000003U << IOU_SLCR_MIO_PIN_28_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_28_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_28_OFFSET ,0x000000FEU ,0x00000018U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_29 @ 0XFF180074</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[2]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_29_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal) - PSU_IOU_SLCR_MIO_PIN_29_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[3]- (PMU GPI) 2= test_scan, Input, test_scan_in[29]- (Test Sc - n Port) = test_scan, Output, test_scan_out[29]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Outp - t, dp_aux_data_out- (Dp Aux Data) - PSU_IOU_SLCR_MIO_PIN_29_L2_SEL 3 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[3]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[3]- (GPIO bank 1) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[0] - (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial inpu - ) 7= trace, Output, tracedq[7]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_29_L3_SEL 0 - - Configures MIO Pin 29 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180074, 0x000000FEU ,0x00000018U) - RegMask = (IOU_SLCR_MIO_PIN_29_L0_SEL_MASK | IOU_SLCR_MIO_PIN_29_L1_SEL_MASK | IOU_SLCR_MIO_PIN_29_L2_SEL_MASK | IOU_SLCR_MIO_PIN_29_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_29_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_29_L1_SEL_SHIFT - | 0x00000003U << IOU_SLCR_MIO_PIN_29_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_29_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_29_OFFSET ,0x000000FEU ,0x00000018U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_30 @ 0XFF180078</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[3]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_30_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal) - PSU_IOU_SLCR_MIO_PIN_30_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[4]- (PMU GPI) 2= test_scan, Input, test_scan_in[30]- (Test Sc - n Port) = test_scan, Output, test_scan_out[30]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug) - PSU_IOU_SLCR_MIO_PIN_30_L2_SEL 3 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[4]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[4]- (GPIO bank 1) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_so - (MISO signal) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output - tracedq[8]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_30_L3_SEL 0 - - Configures MIO Pin 30 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180078, 0x000000FEU ,0x00000018U) - RegMask = (IOU_SLCR_MIO_PIN_30_L0_SEL_MASK | IOU_SLCR_MIO_PIN_30_L1_SEL_MASK | IOU_SLCR_MIO_PIN_30_L2_SEL_MASK | IOU_SLCR_MIO_PIN_30_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_30_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_30_L1_SEL_SHIFT - | 0x00000003U << IOU_SLCR_MIO_PIN_30_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_30_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_30_OFFSET ,0x000000FEU ,0x00000018U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_31 @ 0XFF18007C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_tx_ctl- (TX RGMII control) - PSU_IOU_SLCR_MIO_PIN_31_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal) - PSU_IOU_SLCR_MIO_PIN_31_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[5]- (PMU GPI) 2= test_scan, Input, test_scan_in[31]- (Test Sc - n Port) = test_scan, Output, test_scan_out[31]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper) - PSU_IOU_SLCR_MIO_PIN_31_L2_SEL 0 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[5]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[5]- (GPIO bank 1) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, spi - _si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial out - ut) 7= trace, Output, tracedq[9]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_31_L3_SEL 0 - - Configures MIO Pin 31 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18007C, 0x000000FEU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_PIN_31_L0_SEL_MASK | IOU_SLCR_MIO_PIN_31_L1_SEL_MASK | IOU_SLCR_MIO_PIN_31_L2_SEL_MASK | IOU_SLCR_MIO_PIN_31_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_31_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_31_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_31_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_31_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_31_OFFSET ,0x000000FEU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_32 @ 0XFF180080</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rx_clk- (RX RGMII clock) - PSU_IOU_SLCR_MIO_PIN_32_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dqs_in- (NAND Strobe) 1= nand, Output, nfc_dqs_out- (NAND Strobe - - PSU_IOU_SLCR_MIO_PIN_32_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[0]- (PMU GPI) 2= test_scan, Input, test_scan_in[32]- (Test S - an Port) = test_scan, Output, test_scan_out[32]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper) - PSU_IOU_SLCR_MIO_PIN_32_L2_SEL 1 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[6]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[6]- (GPIO bank 1) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, spi - _sclk_out- (SPI Clock) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= - race, Output, tracedq[10]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_32_L3_SEL 0 - - Configures MIO Pin 32 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180080, 0x000000FEU ,0x00000008U) - RegMask = (IOU_SLCR_MIO_PIN_32_L0_SEL_MASK | IOU_SLCR_MIO_PIN_32_L1_SEL_MASK | IOU_SLCR_MIO_PIN_32_L2_SEL_MASK | IOU_SLCR_MIO_PIN_32_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_32_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_32_L1_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_32_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_32_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_32_OFFSET ,0x000000FEU ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_33 @ 0XFF180084</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[0]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_33_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal) - PSU_IOU_SLCR_MIO_PIN_33_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[1]- (PMU GPI) 2= test_scan, Input, test_scan_in[33]- (Test S - an Port) = test_scan, Output, test_scan_out[33]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper) - PSU_IOU_SLCR_MIO_PIN_33_L2_SEL 1 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[7]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[7]- (GPIO bank 1) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= t - c3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, traced - [11]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_33_L3_SEL 0 - - Configures MIO Pin 33 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180084, 0x000000FEU ,0x00000008U) - RegMask = (IOU_SLCR_MIO_PIN_33_L0_SEL_MASK | IOU_SLCR_MIO_PIN_33_L1_SEL_MASK | IOU_SLCR_MIO_PIN_33_L2_SEL_MASK | IOU_SLCR_MIO_PIN_33_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_33_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_33_L1_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_33_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_33_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_33_OFFSET ,0x000000FEU ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_34 @ 0XFF180088</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[1]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_34_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal) - PSU_IOU_SLCR_MIO_PIN_34_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[2]- (PMU GPI) 2= test_scan, Input, test_scan_in[34]- (Test S - an Port) = test_scan, Output, test_scan_out[34]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Out - ut, dp_aux_data_out- (Dp Aux Data) - PSU_IOU_SLCR_MIO_PIN_34_L2_SEL 1 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[8]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[8]- (GPIO bank 1) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= ttc2 - Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace P - rt Databus) - PSU_IOU_SLCR_MIO_PIN_34_L3_SEL 0 - - Configures MIO Pin 34 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180088, 0x000000FEU ,0x00000008U) - RegMask = (IOU_SLCR_MIO_PIN_34_L0_SEL_MASK | IOU_SLCR_MIO_PIN_34_L1_SEL_MASK | IOU_SLCR_MIO_PIN_34_L2_SEL_MASK | IOU_SLCR_MIO_PIN_34_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_34_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_34_L1_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_34_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_34_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_34_OFFSET ,0x000000FEU ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_35 @ 0XFF18008C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[2]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_35_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal) - PSU_IOU_SLCR_MIO_PIN_35_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[3]- (PMU GPI) 2= test_scan, Input, test_scan_in[35]- (Test S - an Port) = test_scan, Output, test_scan_out[35]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug) - PSU_IOU_SLCR_MIO_PIN_35_L2_SEL 1 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[9]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[9]- (GPIO bank 1) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1, - Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- - UART transmitter serial output) 7= trace, Output, tracedq[13]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_35_L3_SEL 0 - - Configures MIO Pin 35 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18008C, 0x000000FEU ,0x00000008U) - RegMask = (IOU_SLCR_MIO_PIN_35_L0_SEL_MASK | IOU_SLCR_MIO_PIN_35_L1_SEL_MASK | IOU_SLCR_MIO_PIN_35_L2_SEL_MASK | IOU_SLCR_MIO_PIN_35_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_35_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_35_L1_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_35_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_35_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_35_OFFSET ,0x000000FEU ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_36 @ 0XFF180090</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[3]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_36_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal) - PSU_IOU_SLCR_MIO_PIN_36_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[4]- (PMU GPI) 2= test_scan, Input, test_scan_in[36]- (Test S - an Port) = test_scan, Output, test_scan_out[36]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Out - ut, dp_aux_data_out- (Dp Aux Data) - PSU_IOU_SLCR_MIO_PIN_36_L2_SEL 1 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[10]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[10]- (GPIO bank 1) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1 - so- (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace - Output, tracedq[14]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_36_L3_SEL 0 - - Configures MIO Pin 36 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180090, 0x000000FEU ,0x00000008U) - RegMask = (IOU_SLCR_MIO_PIN_36_L0_SEL_MASK | IOU_SLCR_MIO_PIN_36_L1_SEL_MASK | IOU_SLCR_MIO_PIN_36_L2_SEL_MASK | IOU_SLCR_MIO_PIN_36_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_36_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_36_L1_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_36_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_36_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_36_OFFSET ,0x000000FEU ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_37 @ 0XFF180094</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rx_ctl- (RX RGMII control ) - PSU_IOU_SLCR_MIO_PIN_37_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal) - PSU_IOU_SLCR_MIO_PIN_37_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[5]- (PMU GPI) 2= test_scan, Input, test_scan_in[37]- (Test S - an Port) = test_scan, Output, test_scan_out[37]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug) - PSU_IOU_SLCR_MIO_PIN_37_L2_SEL 1 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[11]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[11]- (GPIO bank 1) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, sp - 1_si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) - 7= trace, Output, tracedq[15]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_37_L3_SEL 0 - - Configures MIO Pin 37 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180094, 0x000000FEU ,0x00000008U) - RegMask = (IOU_SLCR_MIO_PIN_37_L0_SEL_MASK | IOU_SLCR_MIO_PIN_37_L1_SEL_MASK | IOU_SLCR_MIO_PIN_37_L2_SEL_MASK | IOU_SLCR_MIO_PIN_37_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_37_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_37_L1_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_37_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_37_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_37_OFFSET ,0x000000FEU ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_38 @ 0XFF180098</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_tx_clk- (TX RGMII clock) - PSU_IOU_SLCR_MIO_PIN_38_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_38_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out- (SDSDIO clock) 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_38_L2_SEL 0 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[12]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[12]- (GPIO bank 1) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Clo - k) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, trace_clk- - (Trace Port Clock) - PSU_IOU_SLCR_MIO_PIN_38_L3_SEL 0 - - Configures MIO Pin 38 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180098, 0x000000FEU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_PIN_38_L0_SEL_MASK | IOU_SLCR_MIO_PIN_38_L1_SEL_MASK | IOU_SLCR_MIO_PIN_38_L2_SEL_MASK | IOU_SLCR_MIO_PIN_38_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_38_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_38_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_38_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_38_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_38_OFFSET ,0x000000FEU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_39 @ 0XFF18009C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[0]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_39_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_39_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD card detect from connector) 2= sd1, Input, sd1_data_i - [4]- (8-bit Data bus) = sd1, Output, sdio1_data_out[4]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_39_L2_SEL 0 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[13]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[13]- (GPIO bank 1) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc0, Output, ttc0_wav - _out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, trace_ctl- (Trace Port - Control Signal) - PSU_IOU_SLCR_MIO_PIN_39_L3_SEL 0 - - Configures MIO Pin 39 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18009C, 0x000000FEU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_PIN_39_L0_SEL_MASK | IOU_SLCR_MIO_PIN_39_L1_SEL_MASK | IOU_SLCR_MIO_PIN_39_L2_SEL_MASK | IOU_SLCR_MIO_PIN_39_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_39_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_39_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_39_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_39_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_39_OFFSET ,0x000000FEU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_40 @ 0XFF1800A0</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[1]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_40_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_40_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Command Indicator) = sd0, Output, sdio0_cmd_out- (Comman - Indicator) 2= sd1, Input, sd1_data_in[5]- (8-bit Data bus) = sd1, Output, sdio1_data_out[5]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_40_L2_SEL 0 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[14]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[14]- (GPIO bank 1) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc3, Input, ttc3_clk - in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[0]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_40_L3_SEL 0 - - Configures MIO Pin 40 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800A0, 0x000000FEU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_PIN_40_L0_SEL_MASK | IOU_SLCR_MIO_PIN_40_L1_SEL_MASK | IOU_SLCR_MIO_PIN_40_L2_SEL_MASK | IOU_SLCR_MIO_PIN_40_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_40_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_40_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_40_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_40_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_40_OFFSET ,0x000000FEU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_41 @ 0XFF1800A4</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[2]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_41_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_41_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]- (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[6]- (8-bit Data bus) = sd1, Output, sdio1_data_out[6]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_41_L2_SEL 0 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[15]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[15]- (GPIO bank 1) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[ - ]- (SPI Master Selects) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial in - ut) 7= trace, Output, tracedq[1]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_41_L3_SEL 0 - - Configures MIO Pin 41 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800A4, 0x000000FEU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_PIN_41_L0_SEL_MASK | IOU_SLCR_MIO_PIN_41_L1_SEL_MASK | IOU_SLCR_MIO_PIN_41_L2_SEL_MASK | IOU_SLCR_MIO_PIN_41_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_41_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_41_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_41_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_41_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_41_OFFSET ,0x000000FEU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_42 @ 0XFF1800A8</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[3]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_42_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_42_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]- (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[7]- (8-bit Data bus) = sd1, Output, sdio1_data_out[7]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_42_L2_SEL 0 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[16]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[16]- (GPIO bank 1) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_ - o- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outp - t, tracedq[2]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_42_L3_SEL 0 - - Configures MIO Pin 42 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800A8, 0x000000FEU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_PIN_42_L0_SEL_MASK | IOU_SLCR_MIO_PIN_42_L1_SEL_MASK | IOU_SLCR_MIO_PIN_42_L2_SEL_MASK | IOU_SLCR_MIO_PIN_42_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_42_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_42_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_42_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_42_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_42_OFFSET ,0x000000FEU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_43 @ 0XFF1800AC</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_tx_ctl- (TX RGMII control) - PSU_IOU_SLCR_MIO_PIN_43_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_43_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]- (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8 - bit Data bus) 2= sd1, Output, sdio1_bus_pow- (SD card bus power) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_43_L2_SEL 2 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[17]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[17]- (GPIO bank 1) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, s - i0_si- (MOSI signal) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o - tput) 7= trace, Output, tracedq[3]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_43_L3_SEL 0 - - Configures MIO Pin 43 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800AC, 0x000000FEU ,0x00000010U) - RegMask = (IOU_SLCR_MIO_PIN_43_L0_SEL_MASK | IOU_SLCR_MIO_PIN_43_L1_SEL_MASK | IOU_SLCR_MIO_PIN_43_L2_SEL_MASK | IOU_SLCR_MIO_PIN_43_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_43_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_43_L1_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_43_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_43_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_43_OFFSET ,0x000000FEU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_44 @ 0XFF1800B0</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rx_clk- (RX RGMII clock) - PSU_IOU_SLCR_MIO_PIN_44_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_44_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]- (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8 - bit Data bus) 2= sd1, Input, sdio1_wp- (SD card write protect from connector) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_44_L2_SEL 2 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[18]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[18]- (GPIO bank 1) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, s - i1_sclk_out- (SPI Clock) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7 - Not Used - PSU_IOU_SLCR_MIO_PIN_44_L3_SEL 0 - - Configures MIO Pin 44 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800B0, 0x000000FEU ,0x00000010U) - RegMask = (IOU_SLCR_MIO_PIN_44_L0_SEL_MASK | IOU_SLCR_MIO_PIN_44_L1_SEL_MASK | IOU_SLCR_MIO_PIN_44_L2_SEL_MASK | IOU_SLCR_MIO_PIN_44_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_44_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_44_L1_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_44_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_44_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_44_OFFSET ,0x000000FEU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_45 @ 0XFF1800B4</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[0]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_45_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_45_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]- (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8 - bit Data bus) 2= sd1, Input, sdio1_cd_n- (SD card detect from connector) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_45_L2_SEL 2 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[19]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[19]- (GPIO bank 1) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= - ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_45_L3_SEL 0 - - Configures MIO Pin 45 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800B4, 0x000000FEU ,0x00000010U) - RegMask = (IOU_SLCR_MIO_PIN_45_L0_SEL_MASK | IOU_SLCR_MIO_PIN_45_L1_SEL_MASK | IOU_SLCR_MIO_PIN_45_L2_SEL_MASK | IOU_SLCR_MIO_PIN_45_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_45_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_45_L1_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_45_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_45_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_45_OFFSET ,0x000000FEU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_46 @ 0XFF1800B8</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[1]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_46_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_46_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]- (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[0]- (8-bit Data bus) = sd1, Output, sdio1_data_out[0]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_46_L2_SEL 2 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[20]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[20]- (GPIO bank 1) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= tt - 0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_46_L3_SEL 0 - - Configures MIO Pin 46 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800B8, 0x000000FEU ,0x00000010U) - RegMask = (IOU_SLCR_MIO_PIN_46_L0_SEL_MASK | IOU_SLCR_MIO_PIN_46_L1_SEL_MASK | IOU_SLCR_MIO_PIN_46_L2_SEL_MASK | IOU_SLCR_MIO_PIN_46_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_46_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_46_L1_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_46_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_46_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_46_OFFSET ,0x000000FEU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_47 @ 0XFF1800BC</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[2]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_47_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_47_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]- (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[1]- (8-bit Data bus) = sd1, Output, sdio1_data_out[1]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_47_L2_SEL 2 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[21]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[21]- (GPIO bank 1) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi - , Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd - (UART transmitter serial output) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_47_L3_SEL 0 - - Configures MIO Pin 47 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800BC, 0x000000FEU ,0x00000010U) - RegMask = (IOU_SLCR_MIO_PIN_47_L0_SEL_MASK | IOU_SLCR_MIO_PIN_47_L1_SEL_MASK | IOU_SLCR_MIO_PIN_47_L2_SEL_MASK | IOU_SLCR_MIO_PIN_47_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_47_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_47_L1_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_47_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_47_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_47_OFFSET ,0x000000FEU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_48 @ 0XFF1800C0</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[3]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_48_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_48_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]- (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[2]- (8-bit Data bus) = sd1, Output, sdio1_data_out[2]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_48_L2_SEL 2 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[22]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[22]- (GPIO bank 1) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1 - so- (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= Not U - ed - PSU_IOU_SLCR_MIO_PIN_48_L3_SEL 0 - - Configures MIO Pin 48 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800C0, 0x000000FEU ,0x00000010U) - RegMask = (IOU_SLCR_MIO_PIN_48_L0_SEL_MASK | IOU_SLCR_MIO_PIN_48_L1_SEL_MASK | IOU_SLCR_MIO_PIN_48_L2_SEL_MASK | IOU_SLCR_MIO_PIN_48_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_48_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_48_L1_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_48_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_48_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_48_OFFSET ,0x000000FEU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_49 @ 0XFF1800C4</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rx_ctl- (RX RGMII control ) - PSU_IOU_SLCR_MIO_PIN_49_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_49_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow- (SD card bus power) 2= sd1, Input, sd1_data_in[3]- (8 - bit Data bus) = sd1, Output, sdio1_data_out[3]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_49_L2_SEL 2 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[23]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[23]- (GPIO bank 1) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, sp - 1_si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) - 7= Not Used - PSU_IOU_SLCR_MIO_PIN_49_L3_SEL 0 - - Configures MIO Pin 49 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800C4, 0x000000FEU ,0x00000010U) - RegMask = (IOU_SLCR_MIO_PIN_49_L0_SEL_MASK | IOU_SLCR_MIO_PIN_49_L1_SEL_MASK | IOU_SLCR_MIO_PIN_49_L2_SEL_MASK | IOU_SLCR_MIO_PIN_49_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_49_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_49_L1_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_49_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_49_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_49_OFFSET ,0x000000FEU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_50 @ 0XFF1800C8</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem_tsu, Input, gem_tsu_clk- (TSU clock) - PSU_IOU_SLCR_MIO_PIN_50_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_50_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD card write protect from connector) 2= sd1, Input, sd1_c - d_in- (Command Indicator) = sd1, Output, sdio1_cmd_out- (Command Indicator) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_50_L2_SEL 2 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[24]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[24]- (GPIO bank 1) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= mdio1, Output, gem1_mdc- (MDIO Clock) 5= ttc2, Input, ttc2 - clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_50_L3_SEL 0 - - Configures MIO Pin 50 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800C8, 0x000000FEU ,0x00000010U) - RegMask = (IOU_SLCR_MIO_PIN_50_L0_SEL_MASK | IOU_SLCR_MIO_PIN_50_L1_SEL_MASK | IOU_SLCR_MIO_PIN_50_L2_SEL_MASK | IOU_SLCR_MIO_PIN_50_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_50_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_50_L1_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_50_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_50_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_50_OFFSET ,0x000000FEU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_51 @ 0XFF1800CC</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem_tsu, Input, gem_tsu_clk- (TSU clock) - PSU_IOU_SLCR_MIO_PIN_51_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_51_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= sd1, Output, sdio1_clk_out- (SDSDIO clock) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_51_L2_SEL 2 - - Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[25]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[25]- (GPIO bank 1) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= mdio1, Input, gem1_mdio_in- (MDIO Data) 4= mdio1, Outp - t, gem1_mdio_out- (MDIO Data) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter - serial output) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_51_L3_SEL 0 - - Configures MIO Pin 51 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800CC, 0x000000FEU ,0x00000010U) - RegMask = (IOU_SLCR_MIO_PIN_51_L0_SEL_MASK | IOU_SLCR_MIO_PIN_51_L1_SEL_MASK | IOU_SLCR_MIO_PIN_51_L2_SEL_MASK | IOU_SLCR_MIO_PIN_51_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_51_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_51_L1_SEL_SHIFT - | 0x00000002U << IOU_SLCR_MIO_PIN_51_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_51_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_51_OFFSET ,0x000000FEU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_52 @ 0XFF1800D0</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_tx_clk- (TX RGMII clock) - PSU_IOU_SLCR_MIO_PIN_52_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_clk_in- (ULPI Clock) - PSU_IOU_SLCR_MIO_PIN_52_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_52_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[0]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[0]- (GPIO bank 2) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Cloc - ) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, trace_ - lk- (Trace Port Clock) - PSU_IOU_SLCR_MIO_PIN_52_L3_SEL 0 - - Configures MIO Pin 52 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800D0, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_52_L0_SEL_MASK | IOU_SLCR_MIO_PIN_52_L1_SEL_MASK | IOU_SLCR_MIO_PIN_52_L2_SEL_MASK | IOU_SLCR_MIO_PIN_52_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_52_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_52_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_52_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_52_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_52_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_53 @ 0XFF1800D4</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[0]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_53_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_dir- (Data bus direction control) - PSU_IOU_SLCR_MIO_PIN_53_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_53_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[1]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[1]- (GPIO bank 2) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave_o - t- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, trace_ctl- (Trace Port Control - Signal) - PSU_IOU_SLCR_MIO_PIN_53_L3_SEL 0 - - Configures MIO Pin 53 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800D4, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_53_L0_SEL_MASK | IOU_SLCR_MIO_PIN_53_L1_SEL_MASK | IOU_SLCR_MIO_PIN_53_L2_SEL_MASK | IOU_SLCR_MIO_PIN_53_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_53_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_53_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_53_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_53_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_53_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_54 @ 0XFF1800D8</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[1]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_54_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[2]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[2]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_54_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_54_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[2]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[2]- (GPIO bank 2) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc0, Input, ttc0_clk_in - (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[0]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_54_L3_SEL 0 - - Configures MIO Pin 54 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800D8, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_54_L0_SEL_MASK | IOU_SLCR_MIO_PIN_54_L1_SEL_MASK | IOU_SLCR_MIO_PIN_54_L2_SEL_MASK | IOU_SLCR_MIO_PIN_54_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_54_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_54_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_54_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_54_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_54_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_55 @ 0XFF1800DC</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[2]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_55_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_nxt- (Data flow control signal from the PHY) - PSU_IOU_SLCR_MIO_PIN_55_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_55_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[3]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[3]- (GPIO bank 2) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[0 - - (SPI Master Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial - output) 7= trace, Output, tracedq[1]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_55_L3_SEL 0 - - Configures MIO Pin 55 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800DC, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_55_L0_SEL_MASK | IOU_SLCR_MIO_PIN_55_L1_SEL_MASK | IOU_SLCR_MIO_PIN_55_L2_SEL_MASK | IOU_SLCR_MIO_PIN_55_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_55_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_55_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_55_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_55_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_55_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_56 @ 0XFF1800E0</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[3]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_56_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[0]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[0]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_56_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_56_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[4]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[4]- (GPIO bank 2) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_s - - (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, - utput, tracedq[2]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_56_L3_SEL 0 - - Configures MIO Pin 56 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800E0, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_56_L0_SEL_MASK | IOU_SLCR_MIO_PIN_56_L1_SEL_MASK | IOU_SLCR_MIO_PIN_56_L2_SEL_MASK | IOU_SLCR_MIO_PIN_56_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_56_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_56_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_56_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_56_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_56_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_57 @ 0XFF1800E4</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_tx_ctl- (TX RGMII control) - PSU_IOU_SLCR_MIO_PIN_57_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[1]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[1]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_57_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_57_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[5]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[5]- (GPIO bank 2) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, spi0 - si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7 - trace, Output, tracedq[3]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_57_L3_SEL 0 - - Configures MIO Pin 57 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800E4, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_57_L0_SEL_MASK | IOU_SLCR_MIO_PIN_57_L1_SEL_MASK | IOU_SLCR_MIO_PIN_57_L2_SEL_MASK | IOU_SLCR_MIO_PIN_57_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_57_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_57_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_57_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_57_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_57_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_58 @ 0XFF1800E8</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rx_clk- (RX RGMII clock) - PSU_IOU_SLCR_MIO_PIN_58_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Output, usb0_ulpi_stp- (Asserted to end or interrupt transfers) - PSU_IOU_SLCR_MIO_PIN_58_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_58_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[6]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[6]- (GPIO bank 2) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, spi1_sclk_out- (SPI Clock - 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[4]- - Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_58_L3_SEL 0 - - Configures MIO Pin 58 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800E8, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_58_L0_SEL_MASK | IOU_SLCR_MIO_PIN_58_L1_SEL_MASK | IOU_SLCR_MIO_PIN_58_L2_SEL_MASK | IOU_SLCR_MIO_PIN_58_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_58_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_58_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_58_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_58_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_58_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_59 @ 0XFF1800EC</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[0]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_59_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[3]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[3]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_59_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_59_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[7]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[7]- (GPIO bank 2) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_ - ut- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, tracedq[5]- (Trace Port - atabus) - PSU_IOU_SLCR_MIO_PIN_59_L3_SEL 0 - - Configures MIO Pin 59 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800EC, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_59_L0_SEL_MASK | IOU_SLCR_MIO_PIN_59_L1_SEL_MASK | IOU_SLCR_MIO_PIN_59_L2_SEL_MASK | IOU_SLCR_MIO_PIN_59_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_59_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_59_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_59_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_59_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_59_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_60 @ 0XFF1800F0</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[1]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_60_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[4]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[4]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_60_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_60_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[8]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[8]- (GPIO bank 2) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= ttc1, Input, ttc1_clk_i - - (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[6]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_60_L3_SEL 0 - - Configures MIO Pin 60 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800F0, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_60_L0_SEL_MASK | IOU_SLCR_MIO_PIN_60_L1_SEL_MASK | IOU_SLCR_MIO_PIN_60_L2_SEL_MASK | IOU_SLCR_MIO_PIN_60_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_60_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_60_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_60_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_60_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_60_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_61 @ 0XFF1800F4</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[2]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_61_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[5]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[5]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_61_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_61_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[9]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[9]- (GPIO bank 2) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1, Output, spi1_n_ss_out[0] - (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial inpu - ) 7= trace, Output, tracedq[7]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_61_L3_SEL 0 - - Configures MIO Pin 61 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800F4, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_61_L0_SEL_MASK | IOU_SLCR_MIO_PIN_61_L1_SEL_MASK | IOU_SLCR_MIO_PIN_61_L2_SEL_MASK | IOU_SLCR_MIO_PIN_61_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_61_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_61_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_61_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_61_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_61_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_62 @ 0XFF1800F8</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[3]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_62_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[6]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[6]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_62_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_62_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[10]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[10]- (GPIO bank 2) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_ - o- (MISO signal) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outp - t, tracedq[8]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_62_L3_SEL 0 - - Configures MIO Pin 62 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800F8, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_62_L0_SEL_MASK | IOU_SLCR_MIO_PIN_62_L1_SEL_MASK | IOU_SLCR_MIO_PIN_62_L2_SEL_MASK | IOU_SLCR_MIO_PIN_62_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_62_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_62_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_62_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_62_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_62_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_63 @ 0XFF1800FC</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rx_ctl- (RX RGMII control ) - PSU_IOU_SLCR_MIO_PIN_63_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[7]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[7]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_63_L1_SEL 1 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_63_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[11]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[11]- (GPIO bank 2) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s - i1_si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o - tput) 7= trace, Output, tracedq[9]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_63_L3_SEL 0 - - Configures MIO Pin 63 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF1800FC, 0x000000FEU ,0x00000004U) - RegMask = (IOU_SLCR_MIO_PIN_63_L0_SEL_MASK | IOU_SLCR_MIO_PIN_63_L1_SEL_MASK | IOU_SLCR_MIO_PIN_63_L2_SEL_MASK | IOU_SLCR_MIO_PIN_63_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_63_L0_SEL_SHIFT - | 0x00000001U << IOU_SLCR_MIO_PIN_63_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_63_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_63_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_63_OFFSET ,0x000000FEU ,0x00000004U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_64 @ 0XFF180100</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_tx_clk- (TX RGMII clock) - PSU_IOU_SLCR_MIO_PIN_64_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_clk_in- (ULPI Clock) - PSU_IOU_SLCR_MIO_PIN_64_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out- (SDSDIO clock) 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_64_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[12]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[12]- (GPIO bank 2) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, s - i0_sclk_out- (SPI Clock) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7 - trace, Output, tracedq[10]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_64_L3_SEL 0 - - Configures MIO Pin 64 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180100, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_64_L0_SEL_MASK | IOU_SLCR_MIO_PIN_64_L1_SEL_MASK | IOU_SLCR_MIO_PIN_64_L2_SEL_MASK | IOU_SLCR_MIO_PIN_64_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_64_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_64_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_64_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_64_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_64_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_65 @ 0XFF180104</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[0]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_65_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_dir- (Data bus direction control) - PSU_IOU_SLCR_MIO_PIN_65_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD card detect from connector) 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_65_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[13]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[13]- (GPIO bank 2) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= - ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, trac - dq[11]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_65_L3_SEL 0 - - Configures MIO Pin 65 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180104, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_65_L0_SEL_MASK | IOU_SLCR_MIO_PIN_65_L1_SEL_MASK | IOU_SLCR_MIO_PIN_65_L2_SEL_MASK | IOU_SLCR_MIO_PIN_65_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_65_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_65_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_65_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_65_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_65_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_66 @ 0XFF180108</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[1]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_66_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[2]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[2]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_66_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Command Indicator) = sd0, Output, sdio0_cmd_out- (Comman - Indicator) 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_66_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[14]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[14]- (GPIO bank 2) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= tt - 2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace - Port Databus) - PSU_IOU_SLCR_MIO_PIN_66_L3_SEL 0 - - Configures MIO Pin 66 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180108, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_66_L0_SEL_MASK | IOU_SLCR_MIO_PIN_66_L1_SEL_MASK | IOU_SLCR_MIO_PIN_66_L2_SEL_MASK | IOU_SLCR_MIO_PIN_66_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_66_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_66_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_66_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_66_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_66_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_67 @ 0XFF18010C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[2]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_67_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_nxt- (Data flow control signal from the PHY) - PSU_IOU_SLCR_MIO_PIN_67_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]- (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8 - bit Data bus) 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_67_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[15]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[15]- (GPIO bank 2) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi - , Output, spi0_n_ss_out[0]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd - (UART transmitter serial output) 7= trace, Output, tracedq[13]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_67_L3_SEL 0 - - Configures MIO Pin 67 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18010C, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_67_L0_SEL_MASK | IOU_SLCR_MIO_PIN_67_L1_SEL_MASK | IOU_SLCR_MIO_PIN_67_L2_SEL_MASK | IOU_SLCR_MIO_PIN_67_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_67_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_67_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_67_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_67_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_67_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_68 @ 0XFF180110</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[3]- (TX RGMII data) - PSU_IOU_SLCR_MIO_PIN_68_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[0]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[0]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_68_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]- (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8 - bit Data bus) 2= Not Used 3= Not Used - PSU_IOU_SLCR_MIO_PIN_68_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[16]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[16]- (GPIO bank 2) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0 - so- (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace - Output, tracedq[14]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_68_L3_SEL 0 - - Configures MIO Pin 68 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180110, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_68_L0_SEL_MASK | IOU_SLCR_MIO_PIN_68_L1_SEL_MASK | IOU_SLCR_MIO_PIN_68_L2_SEL_MASK | IOU_SLCR_MIO_PIN_68_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_68_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_68_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_68_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_68_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_68_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_69 @ 0XFF180114</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_tx_ctl- (TX RGMII control) - PSU_IOU_SLCR_MIO_PIN_69_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[1]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[1]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_69_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]- (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8 - bit Data bus) 2= sd1, Input, sdio1_wp- (SD card write protect from connector) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_69_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[17]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[17]- (GPIO bank 2) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, sp - 0_si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) - 7= trace, Output, tracedq[15]- (Trace Port Databus) - PSU_IOU_SLCR_MIO_PIN_69_L3_SEL 0 - - Configures MIO Pin 69 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180114, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_69_L0_SEL_MASK | IOU_SLCR_MIO_PIN_69_L1_SEL_MASK | IOU_SLCR_MIO_PIN_69_L2_SEL_MASK | IOU_SLCR_MIO_PIN_69_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_69_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_69_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_69_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_69_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_69_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_70 @ 0XFF180118</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rx_clk- (RX RGMII clock) - PSU_IOU_SLCR_MIO_PIN_70_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Output, usb1_ulpi_stp- (Asserted to end or interrupt transfers) - PSU_IOU_SLCR_MIO_PIN_70_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]- (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8 - bit Data bus) 2= sd1, Output, sdio1_bus_pow- (SD card bus power) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_70_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[18]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[18]- (GPIO bank 2) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, sp - 1_sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not - sed - PSU_IOU_SLCR_MIO_PIN_70_L3_SEL 0 - - Configures MIO Pin 70 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180118, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_70_L0_SEL_MASK | IOU_SLCR_MIO_PIN_70_L1_SEL_MASK | IOU_SLCR_MIO_PIN_70_L2_SEL_MASK | IOU_SLCR_MIO_PIN_70_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_70_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_70_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_70_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_70_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_70_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_71 @ 0XFF18011C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[0]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_71_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[3]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[3]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_71_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]- (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[0]- (8-bit Data bus) = sd1, Output, sdio1_data_out[0]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_71_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[19]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[19]- (GPIO bank 2) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5 - ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_71_L3_SEL 0 - - Configures MIO Pin 71 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18011C, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_71_L0_SEL_MASK | IOU_SLCR_MIO_PIN_71_L1_SEL_MASK | IOU_SLCR_MIO_PIN_71_L2_SEL_MASK | IOU_SLCR_MIO_PIN_71_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_71_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_71_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_71_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_71_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_71_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_72 @ 0XFF180120</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[1]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_72_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[4]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[4]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_72_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]- (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[1]- (8-bit Data bus) = sd1, Output, sdio1_data_out[1]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_72_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[20]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[20]- (GPIO bank 2) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= N - t Used 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_72_L3_SEL 0 - - Configures MIO Pin 72 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180120, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_72_L0_SEL_MASK | IOU_SLCR_MIO_PIN_72_L1_SEL_MASK | IOU_SLCR_MIO_PIN_72_L2_SEL_MASK | IOU_SLCR_MIO_PIN_72_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_72_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_72_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_72_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_72_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_72_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_73 @ 0XFF180124</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[2]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_73_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[5]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[5]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_73_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]- (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[2]- (8-bit Data bus) = sd1, Output, sdio1_data_out[2]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_73_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[21]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[21]- (GPIO bank 2) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1 - Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= Not Used 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_73_L3_SEL 0 - - Configures MIO Pin 73 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180124, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_73_L0_SEL_MASK | IOU_SLCR_MIO_PIN_73_L1_SEL_MASK | IOU_SLCR_MIO_PIN_73_L2_SEL_MASK | IOU_SLCR_MIO_PIN_73_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_73_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_73_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_73_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_73_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_73_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_74 @ 0XFF180128</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[3]- (RX RGMII data) - PSU_IOU_SLCR_MIO_PIN_74_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[6]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[6]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_74_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]- (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[3]- (8-bit Data bus) = sd1, Output, sdio1_data_out[3]- (8-bit Data bus) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_74_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[22]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[22]- (GPIO bank 2) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_ - o- (MISO signal) 5= Not Used 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_74_L3_SEL 0 - - Configures MIO Pin 74 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180128, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_74_L0_SEL_MASK | IOU_SLCR_MIO_PIN_74_L1_SEL_MASK | IOU_SLCR_MIO_PIN_74_L2_SEL_MASK | IOU_SLCR_MIO_PIN_74_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_74_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_74_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_74_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_74_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_74_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_75 @ 0XFF18012C</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rx_ctl- (RX RGMII control ) - PSU_IOU_SLCR_MIO_PIN_75_L0_SEL 1 - - Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[7]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[7]- (ULPI data bus) - PSU_IOU_SLCR_MIO_PIN_75_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow- (SD card bus power) 2= sd1, Input, sd1_cmd_in- (Comma - d Indicator) = sd1, Output, sdio1_cmd_out- (Command Indicator) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_75_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[23]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[23]- (GPIO bank 2) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s - i1_si- (MOSI signal) 5= Not Used 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_75_L3_SEL 0 - - Configures MIO Pin 75 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF18012C, 0x000000FEU ,0x00000002U) - RegMask = (IOU_SLCR_MIO_PIN_75_L0_SEL_MASK | IOU_SLCR_MIO_PIN_75_L1_SEL_MASK | IOU_SLCR_MIO_PIN_75_L2_SEL_MASK | IOU_SLCR_MIO_PIN_75_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_MIO_PIN_75_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_75_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_75_L2_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_75_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_75_OFFSET ,0x000000FEU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_76 @ 0XFF180130</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_76_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_76_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD card write protect from connector) 2= sd1, Output, sdio - _clk_out- (SDSDIO clock) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_76_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[24]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[24]- (GPIO bank 2) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= mdio0, Output, gem0_mdc- (MDIO Clock) 4= mdio1, Output, gem1_mdc- (MDIO Clock) 5= mdio2, Output, gem2_mdc- (MDIO Clock - 6= mdio3, Output, gem3_mdc- (MDIO Clock) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_76_L3_SEL 6 - - Configures MIO Pin 76 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180130, 0x000000FEU ,0x000000C0U) - RegMask = (IOU_SLCR_MIO_PIN_76_L0_SEL_MASK | IOU_SLCR_MIO_PIN_76_L1_SEL_MASK | IOU_SLCR_MIO_PIN_76_L2_SEL_MASK | IOU_SLCR_MIO_PIN_76_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_76_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_76_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_76_L2_SEL_SHIFT - | 0x00000006U << IOU_SLCR_MIO_PIN_76_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_76_OFFSET ,0x000000FEU ,0x000000C0U); - /*############################################################################################################################ */ - - /*Register : MIO_PIN_77 @ 0XFF180134</p> - - Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_77_L0_SEL 0 - - Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used - PSU_IOU_SLCR_MIO_PIN_77_L1_SEL 0 - - Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= sd1, Input, sdio1_cd_n- (SD card detect from connector) 3= Not Used - PSU_IOU_SLCR_MIO_PIN_77_L2_SEL 0 - - Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[25]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[25]- (GPIO bank 2) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= mdio0, Input, gem0_mdio_in- (MDIO Data) 3= mdio0, Output, gem0_mdio_out- (MDIO Data) 4= mdio1, Input, gem1_mdio_in- (MD - O Data) 4= mdio1, Output, gem1_mdio_out- (MDIO Data) 5= mdio2, Input, gem2_mdio_in- (MDIO Data) 5= mdio2, Output, gem2_mdio_o - t- (MDIO Data) 6= mdio3, Input, gem3_mdio_in- (MDIO Data) 6= mdio3, Output, gem3_mdio_out- (MDIO Data) 7= Not Used - PSU_IOU_SLCR_MIO_PIN_77_L3_SEL 6 - - Configures MIO Pin 77 peripheral interface mapping - (OFFSET, MASK, VALUE) (0XFF180134, 0x000000FEU ,0x000000C0U) - RegMask = (IOU_SLCR_MIO_PIN_77_L0_SEL_MASK | IOU_SLCR_MIO_PIN_77_L1_SEL_MASK | IOU_SLCR_MIO_PIN_77_L2_SEL_MASK | IOU_SLCR_MIO_PIN_77_L3_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_PIN_77_L0_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_77_L1_SEL_SHIFT - | 0x00000000U << IOU_SLCR_MIO_PIN_77_L2_SEL_SHIFT - | 0x00000006U << IOU_SLCR_MIO_PIN_77_L3_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_PIN_77_OFFSET ,0x000000FEU ,0x000000C0U); - /*############################################################################################################################ */ - - /*Register : MIO_MST_TRI0 @ 0XFF180204</p> - - Master Tri-state Enable for pin 0, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI 0 - - Master Tri-state Enable for pin 1, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI 0 - - Master Tri-state Enable for pin 2, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI 0 - - Master Tri-state Enable for pin 3, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI 0 - - Master Tri-state Enable for pin 4, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI 0 - - Master Tri-state Enable for pin 5, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI 0 - - Master Tri-state Enable for pin 6, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI 0 - - Master Tri-state Enable for pin 7, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI 0 - - Master Tri-state Enable for pin 8, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI 0 - - Master Tri-state Enable for pin 9, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI 0 - - Master Tri-state Enable for pin 10, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI 0 - - Master Tri-state Enable for pin 11, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI 0 - - Master Tri-state Enable for pin 12, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI 0 - - Master Tri-state Enable for pin 13, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI 0 - - Master Tri-state Enable for pin 14, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI 0 - - Master Tri-state Enable for pin 15, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI 0 - - Master Tri-state Enable for pin 16, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI 0 - - Master Tri-state Enable for pin 17, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI 0 - - Master Tri-state Enable for pin 18, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI 1 - - Master Tri-state Enable for pin 19, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI 0 - - Master Tri-state Enable for pin 20, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI 0 - - Master Tri-state Enable for pin 21, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI 1 - - Master Tri-state Enable for pin 22, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI 0 - - Master Tri-state Enable for pin 23, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI 0 - - Master Tri-state Enable for pin 24, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI 0 - - Master Tri-state Enable for pin 25, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI 1 - - Master Tri-state Enable for pin 26, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI 0 - - Master Tri-state Enable for pin 27, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI 0 - - Master Tri-state Enable for pin 28, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI 1 - - Master Tri-state Enable for pin 29, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI 0 - - Master Tri-state Enable for pin 30, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI 1 - - Master Tri-state Enable for pin 31, active high - PSU_IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI 0 - - MIO pin Tri-state Enables, 31:0 - (OFFSET, MASK, VALUE) (0XFF180204, 0xFFFFFFFFU ,0x52240000U) - RegMask = (IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI_MASK | IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_MST_TRI0_OFFSET ,0xFFFFFFFFU ,0x52240000U); - /*############################################################################################################################ */ - - /*Register : MIO_MST_TRI1 @ 0XFF180208</p> - - Master Tri-state Enable for pin 32, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI 0 - - Master Tri-state Enable for pin 33, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI 0 - - Master Tri-state Enable for pin 34, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI 0 - - Master Tri-state Enable for pin 35, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI 0 - - Master Tri-state Enable for pin 36, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI 0 - - Master Tri-state Enable for pin 37, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI 0 - - Master Tri-state Enable for pin 38, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI 0 - - Master Tri-state Enable for pin 39, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI 0 - - Master Tri-state Enable for pin 40, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI 0 - - Master Tri-state Enable for pin 41, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI 0 - - Master Tri-state Enable for pin 42, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI 0 - - Master Tri-state Enable for pin 43, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI 0 - - Master Tri-state Enable for pin 44, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI 1 - - Master Tri-state Enable for pin 45, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI 1 - - Master Tri-state Enable for pin 46, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI 0 - - Master Tri-state Enable for pin 47, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI 0 - - Master Tri-state Enable for pin 48, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI 0 - - Master Tri-state Enable for pin 49, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI 0 - - Master Tri-state Enable for pin 50, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI 0 - - Master Tri-state Enable for pin 51, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI 0 - - Master Tri-state Enable for pin 52, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI 1 - - Master Tri-state Enable for pin 53, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI 1 - - Master Tri-state Enable for pin 54, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI 0 - - Master Tri-state Enable for pin 55, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI 1 - - Master Tri-state Enable for pin 56, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI 0 - - Master Tri-state Enable for pin 57, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI 0 - - Master Tri-state Enable for pin 58, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI 0 - - Master Tri-state Enable for pin 59, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI 0 - - Master Tri-state Enable for pin 60, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI 0 - - Master Tri-state Enable for pin 61, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI 0 - - Master Tri-state Enable for pin 62, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI 0 - - Master Tri-state Enable for pin 63, active high - PSU_IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI 0 - - MIO pin Tri-state Enables, 63:32 - (OFFSET, MASK, VALUE) (0XFF180208, 0xFFFFFFFFU ,0x00B03000U) - RegMask = (IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI_MASK | IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_MST_TRI1_OFFSET ,0xFFFFFFFFU ,0x00B03000U); - /*############################################################################################################################ */ - - /*Register : MIO_MST_TRI2 @ 0XFF18020C</p> - - Master Tri-state Enable for pin 64, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI 0 - - Master Tri-state Enable for pin 65, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI 0 - - Master Tri-state Enable for pin 66, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI 0 - - Master Tri-state Enable for pin 67, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI 0 - - Master Tri-state Enable for pin 68, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI 0 - - Master Tri-state Enable for pin 69, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI 0 - - Master Tri-state Enable for pin 70, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI 1 - - Master Tri-state Enable for pin 71, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI 1 - - Master Tri-state Enable for pin 72, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI 1 - - Master Tri-state Enable for pin 73, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI 1 - - Master Tri-state Enable for pin 74, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI 1 - - Master Tri-state Enable for pin 75, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI 1 - - Master Tri-state Enable for pin 76, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI 0 - - Master Tri-state Enable for pin 77, active high - PSU_IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI 0 - - MIO pin Tri-state Enables, 77:64 - (OFFSET, MASK, VALUE) (0XFF18020C, 0x00003FFFU ,0x00000FC0U) - RegMask = (IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI_MASK | IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI_SHIFT - | 0x00000001U << IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI_SHIFT - | 0x00000000U << IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_MST_TRI2_OFFSET ,0x00003FFFU ,0x00000FC0U); - /*############################################################################################################################ */ - - /*Register : bank0_ctrl0 @ 0XFF180138</p> - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25 1 - - Drive0 control to MIO Bank 0 - control MIO[25:0] - (OFFSET, MASK, VALUE) (0XFF180138, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24_MASK | IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK0_CTRL0_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank0_ctrl1 @ 0XFF18013C</p> - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25 1 - - Drive1 control to MIO Bank 0 - control MIO[25:0] - (OFFSET, MASK, VALUE) (0XFF18013C, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24_MASK | IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK0_CTRL1_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank0_ctrl3 @ 0XFF180140</p> - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25 0 - - Selects either Schmitt or CMOS input for MIO Bank 0 - control MIO[25:0] - (OFFSET, MASK, VALUE) (0XFF180140, 0x03FFFFFFU ,0x00000000U) - RegMask = (IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24_MASK | IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK0_CTRL3_OFFSET ,0x03FFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : bank0_ctrl4 @ 0XFF180144</p> - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25 1 - - When mio_bank0_pull_enable is set, this selects pull up or pull down for MIO Bank 0 - control MIO[25:0] - (OFFSET, MASK, VALUE) (0XFF180144, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24_MASK | IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK0_CTRL4_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank0_ctrl5 @ 0XFF180148</p> - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25 1 - - When set, this enables mio_bank0_pullupdown to selects pull up or pull down for MIO Bank 0 - control MIO[25:0] - (OFFSET, MASK, VALUE) (0XFF180148, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24_MASK | IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK0_CTRL5_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank0_ctrl6 @ 0XFF18014C</p> - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24 0 - - Each bit applies to a single IO. Bit 0 for MIO[0]. - PSU_IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25 0 - - Slew rate control to MIO Bank 0 - control MIO[25:0] - (OFFSET, MASK, VALUE) (0XFF18014C, 0x03FFFFFFU ,0x00000000U) - RegMask = (IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24_MASK | IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24_SHIFT - | 0x00000000U << IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK0_CTRL6_OFFSET ,0x03FFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : bank1_ctrl0 @ 0XFF180154</p> - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25 1 - - Drive0 control to MIO Bank 1 - control MIO[51:26] - (OFFSET, MASK, VALUE) (0XFF180154, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24_MASK | IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK1_CTRL0_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank1_ctrl1 @ 0XFF180158</p> - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25 1 - - Drive1 control to MIO Bank 1 - control MIO[51:26] - (OFFSET, MASK, VALUE) (0XFF180158, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24_MASK | IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK1_CTRL1_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank1_ctrl3 @ 0XFF18015C</p> - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25 0 - - Selects either Schmitt or CMOS input for MIO Bank 1 - control MIO[51:26] - (OFFSET, MASK, VALUE) (0XFF18015C, 0x03FFFFFFU ,0x00000000U) - RegMask = (IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24_MASK | IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK1_CTRL3_OFFSET ,0x03FFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : bank1_ctrl4 @ 0XFF180160</p> - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25 1 - - When mio_bank1_pull_enable is set, this selects pull up or pull down for MIO Bank 1 - control MIO[51:26] - (OFFSET, MASK, VALUE) (0XFF180160, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24_MASK | IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK1_CTRL4_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank1_ctrl5 @ 0XFF180164</p> - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25 1 - - When set, this enables mio_bank1_pullupdown to selects pull up or pull down for MIO Bank 1 - control MIO[51:26] - (OFFSET, MASK, VALUE) (0XFF180164, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24_MASK | IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK1_CTRL5_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank1_ctrl6 @ 0XFF180168</p> - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24 0 - - Each bit applies to a single IO. Bit 0 for MIO[26]. - PSU_IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25 0 - - Slew rate control to MIO Bank 1 - control MIO[51:26] - (OFFSET, MASK, VALUE) (0XFF180168, 0x03FFFFFFU ,0x00000000U) - RegMask = (IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24_MASK | IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24_SHIFT - | 0x00000000U << IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK1_CTRL6_OFFSET ,0x03FFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : bank2_ctrl0 @ 0XFF180170</p> - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25 1 - - Drive0 control to MIO Bank 2 - control MIO[77:52] - (OFFSET, MASK, VALUE) (0XFF180170, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24_MASK | IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK2_CTRL0_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank2_ctrl1 @ 0XFF180174</p> - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25 1 - - Drive1 control to MIO Bank 2 - control MIO[77:52] - (OFFSET, MASK, VALUE) (0XFF180174, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24_MASK | IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK2_CTRL1_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank2_ctrl3 @ 0XFF180178</p> - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25 0 - - Selects either Schmitt or CMOS input for MIO Bank 2 - control MIO[77:52] - (OFFSET, MASK, VALUE) (0XFF180178, 0x03FFFFFFU ,0x00000000U) - RegMask = (IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24_MASK | IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK2_CTRL3_OFFSET ,0x03FFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : bank2_ctrl4 @ 0XFF18017C</p> - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25 1 - - When mio_bank2_pull_enable is set, this selects pull up or pull down for MIO Bank 2 - control MIO[77:52] - (OFFSET, MASK, VALUE) (0XFF18017C, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24_MASK | IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK2_CTRL4_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank2_ctrl5 @ 0XFF180180</p> - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24 1 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25 1 - - When set, this enables mio_bank2_pullupdown to selects pull up or pull down for MIO Bank 2 - control MIO[77:52] - (OFFSET, MASK, VALUE) (0XFF180180, 0x03FFFFFFU ,0x03FFFFFFU) - RegMask = (IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24_MASK | IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24_SHIFT - | 0x00000001U << IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK2_CTRL5_OFFSET ,0x03FFFFFFU ,0x03FFFFFFU); - /*############################################################################################################################ */ - - /*Register : bank2_ctrl6 @ 0XFF180184</p> - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24 0 - - Each bit applies to a single IO. Bit 0 for MIO[52]. - PSU_IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25 0 - - Slew rate control to MIO Bank 2 - control MIO[77:52] - (OFFSET, MASK, VALUE) (0XFF180184, 0x03FFFFFFU ,0x00000000U) - RegMask = (IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24_MASK | IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24_SHIFT - | 0x00000000U << IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_BANK2_CTRL6_OFFSET ,0x03FFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - // : LOOPBACK - /*Register : MIO_LOOPBACK @ 0XFF180200</p> - - I2C Loopback Control. 0 = Connect I2C inputs according to MIO mapping. 1 = Loop I2C 0 outputs to I2C 1 inputs, and I2C 1 outp - ts to I2C 0 inputs. - PSU_IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1 0 - - CAN Loopback Control. 0 = Connect CAN inputs according to MIO mapping. 1 = Loop CAN 0 Tx to CAN 1 Rx, and CAN 1 Tx to CAN 0 R - . - PSU_IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1 0 - - UART Loopback Control. 0 = Connect UART inputs according to MIO mapping. 1 = Loop UART 0 outputs to UART 1 inputs, and UART 1 - outputs to UART 0 inputs. RXD/TXD cross-connected. RTS/CTS cross-connected. DSR, DTR, DCD and RI not used. - PSU_IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1 0 - - SPI Loopback Control. 0 = Connect SPI inputs according to MIO mapping. 1 = Loop SPI 0 outputs to SPI 1 inputs, and SPI 1 outp - ts to SPI 0 inputs. The other SPI core will appear on the LS Slave Select. - PSU_IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1 0 - - Loopback function within MIO - (OFFSET, MASK, VALUE) (0XFF180200, 0x0000000FU ,0x00000000U) - RegMask = (IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1_MASK | IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1_MASK | IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1_MASK | IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1_SHIFT - | 0x00000000U << IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1_SHIFT - | 0x00000000U << IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1_SHIFT - | 0x00000000U << IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_MIO_LOOPBACK_OFFSET ,0x0000000FU ,0x00000000U); - /*############################################################################################################################ */ - - - return 1; -} -unsigned long psu_peripherals_init_data() { - // : RESET BLOCKS - // : TIMESTAMP - /*Register : RST_LPD_IOU2 @ 0XFF5E0238</p> - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_TIMESTAMP_RESET 0 - - Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset. - (OFFSET, MASK, VALUE) (0XFF5E0238, 0x00100000U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_IOU2_TIMESTAMP_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_IOU2_TIMESTAMP_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU2_OFFSET ,0x00100000U ,0x00000000U); - /*############################################################################################################################ */ - - // : ENET - /*Register : RST_LPD_IOU0 @ 0XFF5E0230</p> - - GEM 3 reset - PSU_CRL_APB_RST_LPD_IOU0_GEM3_RESET 0 - - Software controlled reset for the GEMs - (OFFSET, MASK, VALUE) (0XFF5E0230, 0x00000008U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_IOU0_GEM3_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_IOU0_GEM3_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU0_OFFSET ,0x00000008U ,0x00000000U); - /*############################################################################################################################ */ - - // : QSPI - /*Register : RST_LPD_IOU2 @ 0XFF5E0238</p> - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_QSPI_RESET 0 - - Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset. - (OFFSET, MASK, VALUE) (0XFF5E0238, 0x00000001U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_IOU2_QSPI_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_IOU2_QSPI_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU2_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - // : QSPI TAP DELAY - /*Register : IOU_TAPDLY_BYPASS @ 0XFF180390</p> - - 0: Do not by pass the tap delays on the Rx clock signal of LQSPI 1: Bypass the Tap delay on the Rx clock signal of LQSPI - PSU_IOU_SLCR_IOU_TAPDLY_BYPASS_LQSPI_RX 1 - - IOU tap delay bypass for the LQSPI and NAND controllers - (OFFSET, MASK, VALUE) (0XFF180390, 0x00000004U ,0x00000004U) - RegMask = (IOU_SLCR_IOU_TAPDLY_BYPASS_LQSPI_RX_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SLCR_IOU_TAPDLY_BYPASS_LQSPI_RX_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_IOU_TAPDLY_BYPASS_OFFSET ,0x00000004U ,0x00000004U); - /*############################################################################################################################ */ - - // : NAND - // : USB - /*Register : RST_LPD_TOP @ 0XFF5E023C</p> - - USB 0 reset for control registers - PSU_CRL_APB_RST_LPD_TOP_USB0_APB_RESET 0 - - USB 0 sleep circuit reset - PSU_CRL_APB_RST_LPD_TOP_USB0_HIBERRESET 0 - - USB 0 reset - PSU_CRL_APB_RST_LPD_TOP_USB0_CORERESET 0 - - Software control register for the LPD block. - (OFFSET, MASK, VALUE) (0XFF5E023C, 0x00000540U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_TOP_USB0_APB_RESET_MASK | CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_MASK | CRL_APB_RST_LPD_TOP_USB0_CORERESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_TOP_USB0_APB_RESET_SHIFT - | 0x00000000U << CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_SHIFT - | 0x00000000U << CRL_APB_RST_LPD_TOP_USB0_CORERESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_TOP_OFFSET ,0x00000540U ,0x00000000U); - /*############################################################################################################################ */ - - // : FPD RESET - /*Register : RST_FPD_TOP @ 0XFD1A0100</p> - - Display Port block level reset (includes DPDMA) - PSU_CRF_APB_RST_FPD_TOP_DP_RESET 0 - - FPD WDT reset - PSU_CRF_APB_RST_FPD_TOP_SWDT_RESET 0 - - GDMA block level reset - PSU_CRF_APB_RST_FPD_TOP_GDMA_RESET 0 - - Pixel Processor (submodule of GPU) block level reset - PSU_CRF_APB_RST_FPD_TOP_GPU_PP0_RESET 0 - - Pixel Processor (submodule of GPU) block level reset - PSU_CRF_APB_RST_FPD_TOP_GPU_PP1_RESET 0 - - GPU block level reset - PSU_CRF_APB_RST_FPD_TOP_GPU_RESET 0 - - GT block level reset - PSU_CRF_APB_RST_FPD_TOP_GT_RESET 0 - - Sata block level reset - PSU_CRF_APB_RST_FPD_TOP_SATA_RESET 0 - - FPD Block level software controlled reset - (OFFSET, MASK, VALUE) (0XFD1A0100, 0x0001807EU ,0x00000000U) - RegMask = (CRF_APB_RST_FPD_TOP_DP_RESET_MASK | CRF_APB_RST_FPD_TOP_SWDT_RESET_MASK | CRF_APB_RST_FPD_TOP_GDMA_RESET_MASK | CRF_APB_RST_FPD_TOP_GPU_PP0_RESET_MASK | CRF_APB_RST_FPD_TOP_GPU_PP1_RESET_MASK | CRF_APB_RST_FPD_TOP_GPU_RESET_MASK | CRF_APB_RST_FPD_TOP_GT_RESET_MASK | CRF_APB_RST_FPD_TOP_SATA_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_RST_FPD_TOP_DP_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_SWDT_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_GDMA_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_GPU_PP0_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_GPU_PP1_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_GPU_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_GT_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_SATA_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_RST_FPD_TOP_OFFSET ,0x0001807EU ,0x00000000U); - /*############################################################################################################################ */ - - // : SD - /*Register : RST_LPD_IOU2 @ 0XFF5E0238</p> - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_SDIO1_RESET 0 - - Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset. - (OFFSET, MASK, VALUE) (0XFF5E0238, 0x00000040U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_IOU2_SDIO1_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_IOU2_SDIO1_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU2_OFFSET ,0x00000040U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : CTRL_REG_SD @ 0XFF180310</p> - - SD or eMMC selection on SDIO1 0: SD enabled 1: eMMC enabled - PSU_IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL 0 - - SD eMMC selection - (OFFSET, MASK, VALUE) (0XFF180310, 0x00008000U ,0x00000000U) - RegMask = (IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_CTRL_REG_SD_OFFSET ,0x00008000U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : SD_CONFIG_REG2 @ 0XFF180320</p> - - Should be set based on the final product usage 00 - Removable SCard Slot 01 - Embedded Slot for One Device 10 - Shared Bus Sl - t 11 - Reserved - PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE 0 - - 1.8V Support 1: 1.8V supported 0: 1.8V not supported support - PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V 0 - - 3.0V Support 1: 3.0V supported 0: 3.0V not supported support - PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V 0 - - 3.3V Support 1: 3.3V supported 0: 3.3V not supported support - PSU_IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V 1 - - SD Config Register 2 - (OFFSET, MASK, VALUE) (0XFF180320, 0x33800000U ,0x00800000U) - RegMask = (IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE_MASK | IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V_MASK | IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V_MASK | IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE_SHIFT - | 0x00000000U << IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V_SHIFT - | 0x00000000U << IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V_SHIFT - | 0x00000001U << IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_SD_CONFIG_REG2_OFFSET ,0x33800000U ,0x00800000U); - /*############################################################################################################################ */ - - // : SD1 BASE CLOCK - /*Register : SD_CONFIG_REG1 @ 0XFF18031C</p> - - Base Clock Frequency for SD Clock. This is the frequency of the xin_clk. - PSU_IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK 0xc7 - - SD Config Register 1 - (OFFSET, MASK, VALUE) (0XFF18031C, 0x7F800000U ,0x63800000U) - RegMask = (IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK_MASK | 0 ); - - RegVal = ((0x000000C7U << IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_SD_CONFIG_REG1_OFFSET ,0x7F800000U ,0x63800000U); - /*############################################################################################################################ */ - - // : SD1 RETUNER - /*Register : SD_CONFIG_REG3 @ 0XFF180324</p> - - This is the Timer Count for Re-Tuning Timer for Re-Tuning Mode 1 to 3. Setting to 4'b0 disables Re-Tuning Timer. 0h - Get inf - rmation via other source 1h = 1 seconds 2h = 2 seconds 3h = 4 seconds 4h = 8 seconds -- n = 2(n-1) seconds -- Bh = 1024 secon - s Fh - Ch = Reserved - PSU_IOU_SLCR_SD_CONFIG_REG3_SD1_RETUNETMR 0X0 - - SD Config Register 3 - (OFFSET, MASK, VALUE) (0XFF180324, 0x03C00000U ,0x00000000U) - RegMask = (IOU_SLCR_SD_CONFIG_REG3_SD1_RETUNETMR_MASK | 0 ); - - RegVal = ((0x00000000U << IOU_SLCR_SD_CONFIG_REG3_SD1_RETUNETMR_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SLCR_SD_CONFIG_REG3_OFFSET ,0x03C00000U ,0x00000000U); - /*############################################################################################################################ */ - - // : CAN - /*Register : RST_LPD_IOU2 @ 0XFF5E0238</p> - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_CAN1_RESET 0 - - Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset. - (OFFSET, MASK, VALUE) (0XFF5E0238, 0x00000100U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_IOU2_CAN1_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_IOU2_CAN1_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU2_OFFSET ,0x00000100U ,0x00000000U); - /*############################################################################################################################ */ - - // : I2C - /*Register : RST_LPD_IOU2 @ 0XFF5E0238</p> - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_I2C0_RESET 0 - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_I2C1_RESET 0 - - Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset. - (OFFSET, MASK, VALUE) (0XFF5E0238, 0x00000600U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_IOU2_I2C0_RESET_MASK | CRL_APB_RST_LPD_IOU2_I2C1_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_IOU2_I2C0_RESET_SHIFT - | 0x00000000U << CRL_APB_RST_LPD_IOU2_I2C1_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU2_OFFSET ,0x00000600U ,0x00000000U); - /*############################################################################################################################ */ - - // : SWDT - /*Register : RST_LPD_IOU2 @ 0XFF5E0238</p> - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_SWDT_RESET 0 - - Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset. - (OFFSET, MASK, VALUE) (0XFF5E0238, 0x00008000U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_IOU2_SWDT_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_IOU2_SWDT_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU2_OFFSET ,0x00008000U ,0x00000000U); - /*############################################################################################################################ */ - - // : SPI - // : TTC - /*Register : RST_LPD_IOU2 @ 0XFF5E0238</p> - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_TTC0_RESET 0 - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_TTC1_RESET 0 - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_TTC2_RESET 0 - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_TTC3_RESET 0 - - Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset. - (OFFSET, MASK, VALUE) (0XFF5E0238, 0x00007800U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_IOU2_TTC0_RESET_MASK | CRL_APB_RST_LPD_IOU2_TTC1_RESET_MASK | CRL_APB_RST_LPD_IOU2_TTC2_RESET_MASK | CRL_APB_RST_LPD_IOU2_TTC3_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_IOU2_TTC0_RESET_SHIFT - | 0x00000000U << CRL_APB_RST_LPD_IOU2_TTC1_RESET_SHIFT - | 0x00000000U << CRL_APB_RST_LPD_IOU2_TTC2_RESET_SHIFT - | 0x00000000U << CRL_APB_RST_LPD_IOU2_TTC3_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU2_OFFSET ,0x00007800U ,0x00000000U); - /*############################################################################################################################ */ - - // : UART - /*Register : RST_LPD_IOU2 @ 0XFF5E0238</p> - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_UART0_RESET 0 - - Block level reset - PSU_CRL_APB_RST_LPD_IOU2_UART1_RESET 0 - - Software control register for the IOU block. Each bit will cause a singlerperipheral or part of the peripheral to be reset. - (OFFSET, MASK, VALUE) (0XFF5E0238, 0x00000006U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_IOU2_UART0_RESET_MASK | CRL_APB_RST_LPD_IOU2_UART1_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_IOU2_UART0_RESET_SHIFT - | 0x00000000U << CRL_APB_RST_LPD_IOU2_UART1_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU2_OFFSET ,0x00000006U ,0x00000000U); - /*############################################################################################################################ */ - - // : TPIU WIDTH - // : TRACE LOCK ACCESS REGISTER - /*Register : LAR @ 0XFE980FB0</p> - - A write of 0xC5ACCE55 enables further write access to this device. A write of any value other than 0xC5ACCE55 will have the a - fect of removing write access. - PSU_TPIU_LAR_ACCESS_W 0XC5ACCE55 - - This is used to enable write access to device registers. External accesses from a debugger (paddrdbg31 = 1) are not subject t - the Lock Registers. A debugger does not have to unlock the component in order to write and modify the registers in the compo - ent. - (OFFSET, MASK, VALUE) (0XFE980FB0, 0xFFFFFFFFU ,0xC5ACCE55U) - RegMask = (TPIU_LAR_ACCESS_W_MASK | 0 ); - - RegVal = ((0xC5ACCE55U << TPIU_LAR_ACCESS_W_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (TPIU_LAR_OFFSET ,0xFFFFFFFFU ,0xC5ACCE55U); - /*############################################################################################################################ */ - - // : TRACE CURRENT PORT SIZE - /*Register : Current_port_size @ 0XFE980004</p> - - Indicates whether the current port size of the TPIU is 32 bits. - PSU_TPIU_CURRENT_PORT_SIZE_PORT_SIZE_32 1 - - The Current Port Size Register has the same format as the Supported Port Sizes register but only one bit is set, and all othe - s must be zero. Writing values with more than one bit set or setting a bit that is not indicated as supported is not supporte - and causes unpredictable behavior.On reset this defaults to the smallest possible port size, 1 bit, and so reads as 0x000000 - 1.Note : Do not modify the value while the Trace Port is still active, or without correctly stopping the formatter (see Forma - ter and Flush Control Register, 0x304). This can result in data not being aligned to the port width. For example, data on an - -bit Trace Port might not be byte aligned. - (OFFSET, MASK, VALUE) (0XFE980004, 0x80000000U ,0x80000000U) - RegMask = (TPIU_CURRENT_PORT_SIZE_PORT_SIZE_32_MASK | 0 ); - - RegVal = ((0x00000001U << TPIU_CURRENT_PORT_SIZE_PORT_SIZE_32_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (TPIU_CURRENT_PORT_SIZE_OFFSET ,0x80000000U ,0x80000000U); - /*############################################################################################################################ */ - - // : TRACE LOCK ACCESS REGISTER - /*Register : LAR @ 0XFE980FB0</p> - - A write of 0xC5ACCE55 enables further write access to this device. A write of any value other than 0xC5ACCE55 will have the a - fect of removing write access. - PSU_TPIU_LAR_ACCESS_W 0X0 - - This is used to enable write access to device registers. External accesses from a debugger (paddrdbg31 = 1) are not subject t - the Lock Registers. A debugger does not have to unlock the component in order to write and modify the registers in the compo - ent. - (OFFSET, MASK, VALUE) (0XFE980FB0, 0xFFFFFFFFU ,0x00000000U) - RegMask = (TPIU_LAR_ACCESS_W_MASK | 0 ); - - RegVal = ((0x00000000U << TPIU_LAR_ACCESS_W_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (TPIU_LAR_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - // : UART BAUD RATE - /*Register : Baud_rate_divider_reg0 @ 0XFF000034</p> - - Baud rate divider value: 0 - 3: ignored 4 - 255: Baud rate - PSU_UART0_BAUD_RATE_DIVIDER_REG0_BDIV 0x5 - - Baud Rate Divider Register - (OFFSET, MASK, VALUE) (0XFF000034, 0x000000FFU ,0x00000005U) - RegMask = (UART0_BAUD_RATE_DIVIDER_REG0_BDIV_MASK | 0 ); - - RegVal = ((0x00000005U << UART0_BAUD_RATE_DIVIDER_REG0_BDIV_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (UART0_BAUD_RATE_DIVIDER_REG0_OFFSET ,0x000000FFU ,0x00000005U); - /*############################################################################################################################ */ - - /*Register : Baud_rate_gen_reg0 @ 0XFF000018</p> - - Baud Rate Clock Divisor Value: 0: Disables baud_sample 1: Clock divisor bypass (baud_sample = sel_clk) 2 - 65535: baud_sample - PSU_UART0_BAUD_RATE_GEN_REG0_CD 0x8f - - Baud Rate Generator Register. - (OFFSET, MASK, VALUE) (0XFF000018, 0x0000FFFFU ,0x0000008FU) - RegMask = (UART0_BAUD_RATE_GEN_REG0_CD_MASK | 0 ); - - RegVal = ((0x0000008FU << UART0_BAUD_RATE_GEN_REG0_CD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (UART0_BAUD_RATE_GEN_REG0_OFFSET ,0x0000FFFFU ,0x0000008FU); - /*############################################################################################################################ */ - - /*Register : Control_reg0 @ 0XFF000000</p> - - Stop transmitter break: 0: no affect 1: stop transmission of the break after a minimum of one character length and transmit a - high level during 12 bit periods. It can be set regardless of the value of STTBRK. - PSU_UART0_CONTROL_REG0_STPBRK 0x0 - - Start transmitter break: 0: no affect 1: start to transmit a break after the characters currently present in the FIFO and the - transmit shift register have been transmitted. It can only be set if STPBRK (Stop transmitter break) is not high. - PSU_UART0_CONTROL_REG0_STTBRK 0x0 - - Restart receiver timeout counter: 1: receiver timeout counter is restarted. This bit is self clearing once the restart has co - pleted. - PSU_UART0_CONTROL_REG0_RSTTO 0x0 - - Transmit disable: 0: enable transmitter 1: disable transmitter - PSU_UART0_CONTROL_REG0_TXDIS 0x0 - - Transmit enable: 0: disable transmitter 1: enable transmitter, provided the TXDIS field is set to 0. - PSU_UART0_CONTROL_REG0_TXEN 0x1 - - Receive disable: 0: enable 1: disable, regardless of the value of RXEN - PSU_UART0_CONTROL_REG0_RXDIS 0x0 - - Receive enable: 0: disable 1: enable When set to one, the receiver logic is enabled, provided the RXDIS field is set to zero. - PSU_UART0_CONTROL_REG0_RXEN 0x1 - - Software reset for Tx data path: 0: no affect 1: transmitter logic is reset and all pending transmitter data is discarded Thi - bit is self clearing once the reset has completed. - PSU_UART0_CONTROL_REG0_TXRES 0x1 - - Software reset for Rx data path: 0: no affect 1: receiver logic is reset and all pending receiver data is discarded. This bit - is self clearing once the reset has completed. - PSU_UART0_CONTROL_REG0_RXRES 0x1 - - UART Control Register - (OFFSET, MASK, VALUE) (0XFF000000, 0x000001FFU ,0x00000017U) - RegMask = (UART0_CONTROL_REG0_STPBRK_MASK | UART0_CONTROL_REG0_STTBRK_MASK | UART0_CONTROL_REG0_RSTTO_MASK | UART0_CONTROL_REG0_TXDIS_MASK | UART0_CONTROL_REG0_TXEN_MASK | UART0_CONTROL_REG0_RXDIS_MASK | UART0_CONTROL_REG0_RXEN_MASK | UART0_CONTROL_REG0_TXRES_MASK | UART0_CONTROL_REG0_RXRES_MASK | 0 ); - - RegVal = ((0x00000000U << UART0_CONTROL_REG0_STPBRK_SHIFT - | 0x00000000U << UART0_CONTROL_REG0_STTBRK_SHIFT - | 0x00000000U << UART0_CONTROL_REG0_RSTTO_SHIFT - | 0x00000000U << UART0_CONTROL_REG0_TXDIS_SHIFT - | 0x00000001U << UART0_CONTROL_REG0_TXEN_SHIFT - | 0x00000000U << UART0_CONTROL_REG0_RXDIS_SHIFT - | 0x00000001U << UART0_CONTROL_REG0_RXEN_SHIFT - | 0x00000001U << UART0_CONTROL_REG0_TXRES_SHIFT - | 0x00000001U << UART0_CONTROL_REG0_RXRES_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (UART0_CONTROL_REG0_OFFSET ,0x000001FFU ,0x00000017U); - /*############################################################################################################################ */ - - /*Register : mode_reg0 @ 0XFF000004</p> - - Channel mode: Defines the mode of operation of the UART. 00: normal 01: automatic echo 10: local loopback 11: remote loopback - PSU_UART0_MODE_REG0_CHMODE 0x0 - - Number of stop bits: Defines the number of stop bits to detect on receive and to generate on transmit. 00: 1 stop bit 01: 1.5 - stop bits 10: 2 stop bits 11: reserved - PSU_UART0_MODE_REG0_NBSTOP 0x0 - - Parity type select: Defines the expected parity to check on receive and the parity to generate on transmit. 000: even parity - 01: odd parity 010: forced to 0 parity (space) 011: forced to 1 parity (mark) 1xx: no parity - PSU_UART0_MODE_REG0_PAR 0x4 - - Character length select: Defines the number of bits in each character. 11: 6 bits 10: 7 bits 0x: 8 bits - PSU_UART0_MODE_REG0_CHRL 0x0 - - Clock source select: This field defines whether a pre-scalar of 8 is applied to the baud rate generator input clock. 0: clock - source is uart_ref_clk 1: clock source is uart_ref_clk/8 - PSU_UART0_MODE_REG0_CLKS 0x0 - - UART Mode Register - (OFFSET, MASK, VALUE) (0XFF000004, 0x000003FFU ,0x00000020U) - RegMask = (UART0_MODE_REG0_CHMODE_MASK | UART0_MODE_REG0_NBSTOP_MASK | UART0_MODE_REG0_PAR_MASK | UART0_MODE_REG0_CHRL_MASK | UART0_MODE_REG0_CLKS_MASK | 0 ); - - RegVal = ((0x00000000U << UART0_MODE_REG0_CHMODE_SHIFT - | 0x00000000U << UART0_MODE_REG0_NBSTOP_SHIFT - | 0x00000004U << UART0_MODE_REG0_PAR_SHIFT - | 0x00000000U << UART0_MODE_REG0_CHRL_SHIFT - | 0x00000000U << UART0_MODE_REG0_CLKS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (UART0_MODE_REG0_OFFSET ,0x000003FFU ,0x00000020U); - /*############################################################################################################################ */ - - /*Register : Baud_rate_divider_reg0 @ 0XFF010034</p> - - Baud rate divider value: 0 - 3: ignored 4 - 255: Baud rate - PSU_UART1_BAUD_RATE_DIVIDER_REG0_BDIV 0x5 - - Baud Rate Divider Register - (OFFSET, MASK, VALUE) (0XFF010034, 0x000000FFU ,0x00000005U) - RegMask = (UART1_BAUD_RATE_DIVIDER_REG0_BDIV_MASK | 0 ); - - RegVal = ((0x00000005U << UART1_BAUD_RATE_DIVIDER_REG0_BDIV_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (UART1_BAUD_RATE_DIVIDER_REG0_OFFSET ,0x000000FFU ,0x00000005U); - /*############################################################################################################################ */ - - /*Register : Baud_rate_gen_reg0 @ 0XFF010018</p> - - Baud Rate Clock Divisor Value: 0: Disables baud_sample 1: Clock divisor bypass (baud_sample = sel_clk) 2 - 65535: baud_sample - PSU_UART1_BAUD_RATE_GEN_REG0_CD 0x8f - - Baud Rate Generator Register. - (OFFSET, MASK, VALUE) (0XFF010018, 0x0000FFFFU ,0x0000008FU) - RegMask = (UART1_BAUD_RATE_GEN_REG0_CD_MASK | 0 ); - - RegVal = ((0x0000008FU << UART1_BAUD_RATE_GEN_REG0_CD_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (UART1_BAUD_RATE_GEN_REG0_OFFSET ,0x0000FFFFU ,0x0000008FU); - /*############################################################################################################################ */ - - /*Register : Control_reg0 @ 0XFF010000</p> - - Stop transmitter break: 0: no affect 1: stop transmission of the break after a minimum of one character length and transmit a - high level during 12 bit periods. It can be set regardless of the value of STTBRK. - PSU_UART1_CONTROL_REG0_STPBRK 0x0 - - Start transmitter break: 0: no affect 1: start to transmit a break after the characters currently present in the FIFO and the - transmit shift register have been transmitted. It can only be set if STPBRK (Stop transmitter break) is not high. - PSU_UART1_CONTROL_REG0_STTBRK 0x0 - - Restart receiver timeout counter: 1: receiver timeout counter is restarted. This bit is self clearing once the restart has co - pleted. - PSU_UART1_CONTROL_REG0_RSTTO 0x0 - - Transmit disable: 0: enable transmitter 1: disable transmitter - PSU_UART1_CONTROL_REG0_TXDIS 0x0 - - Transmit enable: 0: disable transmitter 1: enable transmitter, provided the TXDIS field is set to 0. - PSU_UART1_CONTROL_REG0_TXEN 0x1 - - Receive disable: 0: enable 1: disable, regardless of the value of RXEN - PSU_UART1_CONTROL_REG0_RXDIS 0x0 - - Receive enable: 0: disable 1: enable When set to one, the receiver logic is enabled, provided the RXDIS field is set to zero. - PSU_UART1_CONTROL_REG0_RXEN 0x1 - - Software reset for Tx data path: 0: no affect 1: transmitter logic is reset and all pending transmitter data is discarded Thi - bit is self clearing once the reset has completed. - PSU_UART1_CONTROL_REG0_TXRES 0x1 - - Software reset for Rx data path: 0: no affect 1: receiver logic is reset and all pending receiver data is discarded. This bit - is self clearing once the reset has completed. - PSU_UART1_CONTROL_REG0_RXRES 0x1 - - UART Control Register - (OFFSET, MASK, VALUE) (0XFF010000, 0x000001FFU ,0x00000017U) - RegMask = (UART1_CONTROL_REG0_STPBRK_MASK | UART1_CONTROL_REG0_STTBRK_MASK | UART1_CONTROL_REG0_RSTTO_MASK | UART1_CONTROL_REG0_TXDIS_MASK | UART1_CONTROL_REG0_TXEN_MASK | UART1_CONTROL_REG0_RXDIS_MASK | UART1_CONTROL_REG0_RXEN_MASK | UART1_CONTROL_REG0_TXRES_MASK | UART1_CONTROL_REG0_RXRES_MASK | 0 ); - - RegVal = ((0x00000000U << UART1_CONTROL_REG0_STPBRK_SHIFT - | 0x00000000U << UART1_CONTROL_REG0_STTBRK_SHIFT - | 0x00000000U << UART1_CONTROL_REG0_RSTTO_SHIFT - | 0x00000000U << UART1_CONTROL_REG0_TXDIS_SHIFT - | 0x00000001U << UART1_CONTROL_REG0_TXEN_SHIFT - | 0x00000000U << UART1_CONTROL_REG0_RXDIS_SHIFT - | 0x00000001U << UART1_CONTROL_REG0_RXEN_SHIFT - | 0x00000001U << UART1_CONTROL_REG0_TXRES_SHIFT - | 0x00000001U << UART1_CONTROL_REG0_RXRES_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (UART1_CONTROL_REG0_OFFSET ,0x000001FFU ,0x00000017U); - /*############################################################################################################################ */ - - /*Register : mode_reg0 @ 0XFF010004</p> - - Channel mode: Defines the mode of operation of the UART. 00: normal 01: automatic echo 10: local loopback 11: remote loopback - PSU_UART1_MODE_REG0_CHMODE 0x0 - - Number of stop bits: Defines the number of stop bits to detect on receive and to generate on transmit. 00: 1 stop bit 01: 1.5 - stop bits 10: 2 stop bits 11: reserved - PSU_UART1_MODE_REG0_NBSTOP 0x0 - - Parity type select: Defines the expected parity to check on receive and the parity to generate on transmit. 000: even parity - 01: odd parity 010: forced to 0 parity (space) 011: forced to 1 parity (mark) 1xx: no parity - PSU_UART1_MODE_REG0_PAR 0x4 - - Character length select: Defines the number of bits in each character. 11: 6 bits 10: 7 bits 0x: 8 bits - PSU_UART1_MODE_REG0_CHRL 0x0 - - Clock source select: This field defines whether a pre-scalar of 8 is applied to the baud rate generator input clock. 0: clock - source is uart_ref_clk 1: clock source is uart_ref_clk/8 - PSU_UART1_MODE_REG0_CLKS 0x0 - - UART Mode Register - (OFFSET, MASK, VALUE) (0XFF010004, 0x000003FFU ,0x00000020U) - RegMask = (UART1_MODE_REG0_CHMODE_MASK | UART1_MODE_REG0_NBSTOP_MASK | UART1_MODE_REG0_PAR_MASK | UART1_MODE_REG0_CHRL_MASK | UART1_MODE_REG0_CLKS_MASK | 0 ); - - RegVal = ((0x00000000U << UART1_MODE_REG0_CHMODE_SHIFT - | 0x00000000U << UART1_MODE_REG0_NBSTOP_SHIFT - | 0x00000004U << UART1_MODE_REG0_PAR_SHIFT - | 0x00000000U << UART1_MODE_REG0_CHRL_SHIFT - | 0x00000000U << UART1_MODE_REG0_CLKS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (UART1_MODE_REG0_OFFSET ,0x000003FFU ,0x00000020U); - /*############################################################################################################################ */ - - // : GPIO - // : ADMA TZ - /*Register : slcr_adma @ 0XFF4B0024</p> - - TrustZone Classification for ADMA - PSU_LPD_SLCR_SECURE_SLCR_ADMA_TZ 0XFF - - RPU TrustZone settings - (OFFSET, MASK, VALUE) (0XFF4B0024, 0x000000FFU ,0x000000FFU) - RegMask = (LPD_SLCR_SECURE_SLCR_ADMA_TZ_MASK | 0 ); - - RegVal = ((0x000000FFU << LPD_SLCR_SECURE_SLCR_ADMA_TZ_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_SLCR_SECURE_SLCR_ADMA_OFFSET ,0x000000FFU ,0x000000FFU); - /*############################################################################################################################ */ - - // : CSU TAMPERING - // : CSU TAMPER STATUS - /*Register : tamper_status @ 0XFFCA5000</p> - - CSU regsiter - PSU_CSU_TAMPER_STATUS_TAMPER_0 0 - - External MIO - PSU_CSU_TAMPER_STATUS_TAMPER_1 0 - - JTAG toggle detect - PSU_CSU_TAMPER_STATUS_TAMPER_2 0 - - PL SEU error - PSU_CSU_TAMPER_STATUS_TAMPER_3 0 - - AMS over temperature alarm for LPD - PSU_CSU_TAMPER_STATUS_TAMPER_4 0 - - AMS over temperature alarm for APU - PSU_CSU_TAMPER_STATUS_TAMPER_5 0 - - AMS voltage alarm for VCCPINT_FPD - PSU_CSU_TAMPER_STATUS_TAMPER_6 0 - - AMS voltage alarm for VCCPINT_LPD - PSU_CSU_TAMPER_STATUS_TAMPER_7 0 - - AMS voltage alarm for VCCPAUX - PSU_CSU_TAMPER_STATUS_TAMPER_8 0 - - AMS voltage alarm for DDRPHY - PSU_CSU_TAMPER_STATUS_TAMPER_9 0 - - AMS voltage alarm for PSIO bank 0/1/2 - PSU_CSU_TAMPER_STATUS_TAMPER_10 0 - - AMS voltage alarm for PSIO bank 3 (dedicated pins) - PSU_CSU_TAMPER_STATUS_TAMPER_11 0 - - AMS voltaage alarm for GT - PSU_CSU_TAMPER_STATUS_TAMPER_12 0 - - Tamper Response Status - (OFFSET, MASK, VALUE) (0XFFCA5000, 0x00001FFFU ,0x00000000U) - RegMask = (CSU_TAMPER_STATUS_TAMPER_0_MASK | CSU_TAMPER_STATUS_TAMPER_1_MASK | CSU_TAMPER_STATUS_TAMPER_2_MASK | CSU_TAMPER_STATUS_TAMPER_3_MASK | CSU_TAMPER_STATUS_TAMPER_4_MASK | CSU_TAMPER_STATUS_TAMPER_5_MASK | CSU_TAMPER_STATUS_TAMPER_6_MASK | CSU_TAMPER_STATUS_TAMPER_7_MASK | CSU_TAMPER_STATUS_TAMPER_8_MASK | CSU_TAMPER_STATUS_TAMPER_9_MASK | CSU_TAMPER_STATUS_TAMPER_10_MASK | CSU_TAMPER_STATUS_TAMPER_11_MASK | CSU_TAMPER_STATUS_TAMPER_12_MASK | 0 ); - - RegVal = ((0x00000000U << CSU_TAMPER_STATUS_TAMPER_0_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_1_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_2_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_3_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_4_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_5_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_6_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_7_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_8_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_9_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_10_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_11_SHIFT - | 0x00000000U << CSU_TAMPER_STATUS_TAMPER_12_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CSU_TAMPER_STATUS_OFFSET ,0x00001FFFU ,0x00000000U); - /*############################################################################################################################ */ - - // : CSU TAMPER RESPONSE - // : CPU QOS DEFAULT - /*Register : ACE_CTRL @ 0XFD5C0060</p> - - Set ACE outgoing AWQOS value - PSU_APU_ACE_CTRL_AWQOS 0X0 - - Set ACE outgoing ARQOS value - PSU_APU_ACE_CTRL_ARQOS 0X0 - - ACE Control Register - (OFFSET, MASK, VALUE) (0XFD5C0060, 0x000F000FU ,0x00000000U) - RegMask = (APU_ACE_CTRL_AWQOS_MASK | APU_ACE_CTRL_ARQOS_MASK | 0 ); - - RegVal = ((0x00000000U << APU_ACE_CTRL_AWQOS_SHIFT - | 0x00000000U << APU_ACE_CTRL_ARQOS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (APU_ACE_CTRL_OFFSET ,0x000F000FU ,0x00000000U); - /*############################################################################################################################ */ - - // : ENABLES RTC SWITCH TO BATTERY WHEN VCC_PSAUX IS NOT AVAILABLE - /*Register : CONTROL @ 0XFFA60040</p> - - Enables the RTC. By writing a 0 to this bit, RTC will be powered off and the only module that potentially draws current from - he battery will be BBRAM. The value read through this bit does not necessarily reflect whether RTC is enabled or not. It is e - pected that RTC is enabled every time it is being configured. If RTC is not used in the design, FSBL will disable it by writi - g a 0 to this bit. - PSU_RTC_CONTROL_BATTERY_DISABLE 0X1 - - This register controls various functionalities within the RTC - (OFFSET, MASK, VALUE) (0XFFA60040, 0x80000000U ,0x80000000U) - RegMask = (RTC_CONTROL_BATTERY_DISABLE_MASK | 0 ); - - RegVal = ((0x00000001U << RTC_CONTROL_BATTERY_DISABLE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (RTC_CONTROL_OFFSET ,0x80000000U ,0x80000000U); - /*############################################################################################################################ */ - - // : TIMESTAMP COUNTER - /*Register : base_frequency_ID_register @ 0XFF260020</p> - - Frequency in number of ticks per second. Valid range from 10 MHz to 100 MHz. - PSU_IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_FREQ 0x5f5e100 - - Program this register to match the clock frequency of the timestamp generator, in ticks per second. For example, for a 50 MHz - clock, program 0x02FAF080. This register is not accessible to the read-only programming interface. - (OFFSET, MASK, VALUE) (0XFF260020, 0xFFFFFFFFU ,0x05F5E100U) - RegMask = (IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_FREQ_MASK | 0 ); - - RegVal = ((0x05F5E100U << IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_FREQ_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_OFFSET ,0xFFFFFFFFU ,0x05F5E100U); - /*############################################################################################################################ */ - - /*Register : counter_control_register @ 0XFF260000</p> - - Enable 0: The counter is disabled and not incrementing. 1: The counter is enabled and is incrementing. - PSU_IOU_SCNTRS_COUNTER_CONTROL_REGISTER_EN 0x1 - - Controls the counter increments. This register is not accessible to the read-only programming interface. - (OFFSET, MASK, VALUE) (0XFF260000, 0x00000001U ,0x00000001U) - RegMask = (IOU_SCNTRS_COUNTER_CONTROL_REGISTER_EN_MASK | 0 ); - - RegVal = ((0x00000001U << IOU_SCNTRS_COUNTER_CONTROL_REGISTER_EN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (IOU_SCNTRS_COUNTER_CONTROL_REGISTER_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - // : TTC SRC SELECT - - return 1; -} -unsigned long psu_post_config_data() { - // : POST_CONFIG - - return 1; -} -unsigned long psu_peripherals_powerdwn_data() { - // : POWER DOWN REQUEST INTERRUPT ENABLE - // : POWER DOWN TRIGGER - - return 1; -} -unsigned long psu_lpd_xppu_data() { - // : MASTER ID LIST - /*Register : MASTER_ID00 @ 0XFF980100</p> - - If set, only read transactions are allowed for the masters matching this register - PSU_LPD_XPPU_CFG_MASTER_ID00_MIDR 1 - - Mask to be applied before comparing - PSU_LPD_XPPU_CFG_MASTER_ID00_MIDM 960 - - Predefined Master ID for PMU - PSU_LPD_XPPU_CFG_MASTER_ID00_MID 128 - - Master ID 00 Register - (OFFSET, MASK, VALUE) (0XFF980100, 0x43FF03FFU ,0x43C00080U) - RegMask = (LPD_XPPU_CFG_MASTER_ID00_MIDR_MASK | LPD_XPPU_CFG_MASTER_ID00_MIDM_MASK | LPD_XPPU_CFG_MASTER_ID00_MID_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_MASTER_ID00_MIDR_SHIFT - | 0x000003C0U << LPD_XPPU_CFG_MASTER_ID00_MIDM_SHIFT - | 0x00000080U << LPD_XPPU_CFG_MASTER_ID00_MID_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_MASTER_ID00_OFFSET ,0x43FF03FFU ,0x43C00080U); - /*############################################################################################################################ */ - - /*Register : MASTER_ID01 @ 0XFF980104</p> - - If set, only read transactions are allowed for the masters matching this register - PSU_LPD_XPPU_CFG_MASTER_ID01_MIDR 1 - - Mask to be applied before comparing - PSU_LPD_XPPU_CFG_MASTER_ID01_MIDM 1023 - - Predefined Master ID for RPU0 - PSU_LPD_XPPU_CFG_MASTER_ID01_MID 64 - - Master ID 01 Register - (OFFSET, MASK, VALUE) (0XFF980104, 0x43FF03FFU ,0x43FF0040U) - RegMask = (LPD_XPPU_CFG_MASTER_ID01_MIDR_MASK | LPD_XPPU_CFG_MASTER_ID01_MIDM_MASK | LPD_XPPU_CFG_MASTER_ID01_MID_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_MASTER_ID01_MIDR_SHIFT - | 0x000003FFU << LPD_XPPU_CFG_MASTER_ID01_MIDM_SHIFT - | 0x00000040U << LPD_XPPU_CFG_MASTER_ID01_MID_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_MASTER_ID01_OFFSET ,0x43FF03FFU ,0x43FF0040U); - /*############################################################################################################################ */ - - /*Register : MASTER_ID02 @ 0XFF980108</p> - - If set, only read transactions are allowed for the masters matching this register - PSU_LPD_XPPU_CFG_MASTER_ID02_MIDR 1 - - Mask to be applied before comparing - PSU_LPD_XPPU_CFG_MASTER_ID02_MIDM 1008 - - Predefined Master ID for RPU1 - PSU_LPD_XPPU_CFG_MASTER_ID02_MID 0 - - Master ID 02 Register - (OFFSET, MASK, VALUE) (0XFF980108, 0x43FF03FFU ,0x43F00000U) - RegMask = (LPD_XPPU_CFG_MASTER_ID02_MIDR_MASK | LPD_XPPU_CFG_MASTER_ID02_MIDM_MASK | LPD_XPPU_CFG_MASTER_ID02_MID_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_MASTER_ID02_MIDR_SHIFT - | 0x000003F0U << LPD_XPPU_CFG_MASTER_ID02_MIDM_SHIFT - | 0x00000000U << LPD_XPPU_CFG_MASTER_ID02_MID_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_MASTER_ID02_OFFSET ,0x43FF03FFU ,0x43F00000U); - /*############################################################################################################################ */ - - /*Register : MASTER_ID03 @ 0XFF98010C</p> - - If set, only read transactions are allowed for the masters matching this register - PSU_LPD_XPPU_CFG_MASTER_ID03_MIDR 1 - - Mask to be applied before comparing - PSU_LPD_XPPU_CFG_MASTER_ID03_MIDM 1008 - - Predefined Master ID for APU - PSU_LPD_XPPU_CFG_MASTER_ID03_MID 16 - - Master ID 03 Register - (OFFSET, MASK, VALUE) (0XFF98010C, 0x43FF03FFU ,0x43F00010U) - RegMask = (LPD_XPPU_CFG_MASTER_ID03_MIDR_MASK | LPD_XPPU_CFG_MASTER_ID03_MIDM_MASK | LPD_XPPU_CFG_MASTER_ID03_MID_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_MASTER_ID03_MIDR_SHIFT - | 0x000003F0U << LPD_XPPU_CFG_MASTER_ID03_MIDM_SHIFT - | 0x00000010U << LPD_XPPU_CFG_MASTER_ID03_MID_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_MASTER_ID03_OFFSET ,0x43FF03FFU ,0x43F00010U); - /*############################################################################################################################ */ - - /*Register : MASTER_ID04 @ 0XFF980110</p> - - If set, only read transactions are allowed for the masters matching this register - PSU_LPD_XPPU_CFG_MASTER_ID04_MIDR 0 - - Mask to be applied before comparing - PSU_LPD_XPPU_CFG_MASTER_ID04_MIDM 960 - - Predefined Master ID for A53 Core 0 - PSU_LPD_XPPU_CFG_MASTER_ID04_MID 128 - - Master ID 04 Register - (OFFSET, MASK, VALUE) (0XFF980110, 0x43FF03FFU ,0x03C00080U) - RegMask = (LPD_XPPU_CFG_MASTER_ID04_MIDR_MASK | LPD_XPPU_CFG_MASTER_ID04_MIDM_MASK | LPD_XPPU_CFG_MASTER_ID04_MID_MASK | 0 ); - - RegVal = ((0x00000000U << LPD_XPPU_CFG_MASTER_ID04_MIDR_SHIFT - | 0x000003C0U << LPD_XPPU_CFG_MASTER_ID04_MIDM_SHIFT - | 0x00000080U << LPD_XPPU_CFG_MASTER_ID04_MID_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_MASTER_ID04_OFFSET ,0x43FF03FFU ,0x03C00080U); - /*############################################################################################################################ */ - - /*Register : MASTER_ID05 @ 0XFF980114</p> - - If set, only read transactions are allowed for the masters matching this register - PSU_LPD_XPPU_CFG_MASTER_ID05_MIDR 0 - - Mask to be applied before comparing - PSU_LPD_XPPU_CFG_MASTER_ID05_MIDM 1023 - - Predefined Master ID for A53 Core 1 - PSU_LPD_XPPU_CFG_MASTER_ID05_MID 64 - - Master ID 05 Register - (OFFSET, MASK, VALUE) (0XFF980114, 0x43FF03FFU ,0x03FF0040U) - RegMask = (LPD_XPPU_CFG_MASTER_ID05_MIDR_MASK | LPD_XPPU_CFG_MASTER_ID05_MIDM_MASK | LPD_XPPU_CFG_MASTER_ID05_MID_MASK | 0 ); - - RegVal = ((0x00000000U << LPD_XPPU_CFG_MASTER_ID05_MIDR_SHIFT - | 0x000003FFU << LPD_XPPU_CFG_MASTER_ID05_MIDM_SHIFT - | 0x00000040U << LPD_XPPU_CFG_MASTER_ID05_MID_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_MASTER_ID05_OFFSET ,0x43FF03FFU ,0x03FF0040U); - /*############################################################################################################################ */ - - /*Register : MASTER_ID06 @ 0XFF980118</p> - - If set, only read transactions are allowed for the masters matching this register - PSU_LPD_XPPU_CFG_MASTER_ID06_MIDR 0 - - Mask to be applied before comparing - PSU_LPD_XPPU_CFG_MASTER_ID06_MIDM 1008 - - Predefined Master ID for A53 Core 2 - PSU_LPD_XPPU_CFG_MASTER_ID06_MID 0 - - Master ID 06 Register - (OFFSET, MASK, VALUE) (0XFF980118, 0x43FF03FFU ,0x03F00000U) - RegMask = (LPD_XPPU_CFG_MASTER_ID06_MIDR_MASK | LPD_XPPU_CFG_MASTER_ID06_MIDM_MASK | LPD_XPPU_CFG_MASTER_ID06_MID_MASK | 0 ); - - RegVal = ((0x00000000U << LPD_XPPU_CFG_MASTER_ID06_MIDR_SHIFT - | 0x000003F0U << LPD_XPPU_CFG_MASTER_ID06_MIDM_SHIFT - | 0x00000000U << LPD_XPPU_CFG_MASTER_ID06_MID_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_MASTER_ID06_OFFSET ,0x43FF03FFU ,0x03F00000U); - /*############################################################################################################################ */ - - /*Register : MASTER_ID07 @ 0XFF98011C</p> - - If set, only read transactions are allowed for the masters matching this register - PSU_LPD_XPPU_CFG_MASTER_ID07_MIDR 0 - - Mask to be applied before comparing - PSU_LPD_XPPU_CFG_MASTER_ID07_MIDM 1008 - - Predefined Master ID for A53 Core 3 - PSU_LPD_XPPU_CFG_MASTER_ID07_MID 16 - - Master ID 07 Register - (OFFSET, MASK, VALUE) (0XFF98011C, 0x43FF03FFU ,0x03F00010U) - RegMask = (LPD_XPPU_CFG_MASTER_ID07_MIDR_MASK | LPD_XPPU_CFG_MASTER_ID07_MIDM_MASK | LPD_XPPU_CFG_MASTER_ID07_MID_MASK | 0 ); - - RegVal = ((0x00000000U << LPD_XPPU_CFG_MASTER_ID07_MIDR_SHIFT - | 0x000003F0U << LPD_XPPU_CFG_MASTER_ID07_MIDM_SHIFT - | 0x00000010U << LPD_XPPU_CFG_MASTER_ID07_MID_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_MASTER_ID07_OFFSET ,0x43FF03FFU ,0x03F00010U); - /*############################################################################################################################ */ - - /*Register : MASTER_ID19 @ 0XFF98014C</p> - - If set, only read transactions are allowed for the masters matching this register - PSU_LPD_XPPU_CFG_MASTER_ID19_MIDR 0 - - Mask to be applied before comparing - PSU_LPD_XPPU_CFG_MASTER_ID19_MIDM 0 - - Programmable Master ID - PSU_LPD_XPPU_CFG_MASTER_ID19_MID 0 - - Master ID 19 Register - (OFFSET, MASK, VALUE) (0XFF98014C, 0x43FF03FFU ,0x00000000U) - RegMask = (LPD_XPPU_CFG_MASTER_ID19_MIDR_MASK | LPD_XPPU_CFG_MASTER_ID19_MIDM_MASK | LPD_XPPU_CFG_MASTER_ID19_MID_MASK | 0 ); - - RegVal = ((0x00000000U << LPD_XPPU_CFG_MASTER_ID19_MIDR_SHIFT - | 0x00000000U << LPD_XPPU_CFG_MASTER_ID19_MIDM_SHIFT - | 0x00000000U << LPD_XPPU_CFG_MASTER_ID19_MID_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_MASTER_ID19_OFFSET ,0x43FF03FFU ,0x00000000U); - /*############################################################################################################################ */ - - // : APERTURE PERMISIION LIST - // : APERTURE NAME: UART0, START ADDRESS: FF000000, END ADDRESS: FF00FFFF - // : APERTURE NAME: UART1, START ADDRESS: FF010000, END ADDRESS: FF01FFFF - // : APERTURE NAME: I2C0, START ADDRESS: FF020000, END ADDRESS: FF02FFFF - // : APERTURE NAME: I2C1, START ADDRESS: FF030000, END ADDRESS: FF03FFFF - // : APERTURE NAME: SPI0, START ADDRESS: FF040000, END ADDRESS: FF04FFFF - // : APERTURE NAME: SPI1, START ADDRESS: FF050000, END ADDRESS: FF05FFFF - // : APERTURE NAME: CAN0, START ADDRESS: FF060000, END ADDRESS: FF06FFFF - // : APERTURE NAME: CAN1, START ADDRESS: FF070000, END ADDRESS: FF07FFFF - // : APERTURE NAME: RPU_UNUSED_12, START ADDRESS: FF080000, END ADDRESS: FF09FFFF - // : APERTURE NAME: RPU_UNUSED_12, START ADDRESS: FF080000, END ADDRESS: FF09FFFF - // : APERTURE NAME: GPIO, START ADDRESS: FF0A0000, END ADDRESS: FF0AFFFF - // : APERTURE NAME: GEM0, START ADDRESS: FF0B0000, END ADDRESS: FF0BFFFF - // : APERTURE NAME: GEM1, START ADDRESS: FF0C0000, END ADDRESS: FF0CFFFF - // : APERTURE NAME: GEM2, START ADDRESS: FF0D0000, END ADDRESS: FF0DFFFF - // : APERTURE NAME: GEM3, START ADDRESS: FF0E0000, END ADDRESS: FF0EFFFF - // : APERTURE NAME: QSPI, START ADDRESS: FF0F0000, END ADDRESS: FF0FFFFF - // : APERTURE NAME: NAND, START ADDRESS: FF100000, END ADDRESS: FF10FFFF - // : APERTURE NAME: TTC0, START ADDRESS: FF110000, END ADDRESS: FF11FFFF - // : APERTURE NAME: TTC1, START ADDRESS: FF120000, END ADDRESS: FF12FFFF - // : APERTURE NAME: TTC2, START ADDRESS: FF130000, END ADDRESS: FF13FFFF - // : APERTURE NAME: TTC3, START ADDRESS: FF140000, END ADDRESS: FF14FFFF - // : APERTURE NAME: SWDT, START ADDRESS: FF150000, END ADDRESS: FF15FFFF - // : APERTURE NAME: SD0, START ADDRESS: FF160000, END ADDRESS: FF16FFFF - // : APERTURE NAME: SD1, START ADDRESS: FF170000, END ADDRESS: FF17FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SLCR, START ADDRESS: FF180000, END ADDRESS: FF23FFFF - // : APERTURE NAME: IOU_SECURE_SLCR, START ADDRESS: FF240000, END ADDRESS: FF24FFFF - // : APERTURE NAME: IOU_SCNTR, START ADDRESS: FF250000, END ADDRESS: FF25FFFF - // : APERTURE NAME: IOU_SCNTRS, START ADDRESS: FF260000, END ADDRESS: FF26FFFF - // : APERTURE NAME: RPU_UNUSED_11, START ADDRESS: FF270000, END ADDRESS: FF2AFFFF - // : APERTURE NAME: RPU_UNUSED_11, START ADDRESS: FF270000, END ADDRESS: FF2AFFFF - // : APERTURE NAME: RPU_UNUSED_11, START ADDRESS: FF270000, END ADDRESS: FF2AFFFF - // : APERTURE NAME: RPU_UNUSED_11, START ADDRESS: FF270000, END ADDRESS: FF2AFFFF - // : APERTURE NAME: LPD_UNUSED_14, START ADDRESS: FF2B0000, END ADDRESS: FF2FFFFF - // : APERTURE NAME: LPD_UNUSED_14, START ADDRESS: FF2B0000, END ADDRESS: FF2FFFFF - // : APERTURE NAME: LPD_UNUSED_14, START ADDRESS: FF2B0000, END ADDRESS: FF2FFFFF - // : APERTURE NAME: LPD_UNUSED_14, START ADDRESS: FF2B0000, END ADDRESS: FF2FFFFF - // : APERTURE NAME: LPD_UNUSED_14, START ADDRESS: FF2B0000, END ADDRESS: FF2FFFFF - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_048 @ 0XFF9810C0</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_048_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_048_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_048_PARITY 0x0 - - Entry 048 of the Aperture Permission List, for the 64K-byte aperture at BASE_64KB + 0x00300000 - (OFFSET, MASK, VALUE) (0XFF9810C0, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_048_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_048_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_048_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_048_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_048_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_048_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_048_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_049 @ 0XFF9810C4</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_049_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_049_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_049_PARITY 0x0 - - Entry 049 of the Aperture Permission List, for the 64K-byte aperture at BASE_64KB + 0x00310000 - (OFFSET, MASK, VALUE) (0XFF9810C4, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_049_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_049_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_049_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_049_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_049_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_049_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_049_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_050 @ 0XFF9810C8</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_050_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_050_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_050_PARITY 0x0 - - Entry 050 of the Aperture Permission List, for the 64K-byte aperture at BASE_64KB + 0x00320000 - (OFFSET, MASK, VALUE) (0XFF9810C8, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_050_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_050_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_050_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_050_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_050_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_050_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_050_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_051 @ 0XFF9810CC</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_051_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_051_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_051_PARITY 0x0 - - Entry 051 of the Aperture Permission List, for the 64K-byte aperture at BASE_64KB + 0x00330000 - (OFFSET, MASK, VALUE) (0XFF9810CC, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_051_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_051_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_051_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_051_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_051_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_051_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_051_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - // : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF - // : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF - // : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF - // : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF - // : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF - // : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF - // : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF - // : APERTURE NAME: IPI_CTRL, START ADDRESS: FF380000, END ADDRESS: FF3FFFFF - // : APERTURE NAME: LPD_UNUSED_1, START ADDRESS: FF400000, END ADDRESS: FF40FFFF - // : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF - // : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF - // : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF - // : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF - // : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF - // : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF - // : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF - // : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF - // : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF - // : APERTURE NAME: LPD_SLCR, START ADDRESS: FF410000, END ADDRESS: FF4AFFFF - // : APERTURE NAME: LPD_SLCR_SECURE, START ADDRESS: FF4B0000, END ADDRESS: FF4DFFFF - // : APERTURE NAME: LPD_SLCR_SECURE, START ADDRESS: FF4B0000, END ADDRESS: FF4DFFFF - // : APERTURE NAME: LPD_SLCR_SECURE, START ADDRESS: FF4B0000, END ADDRESS: FF4DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: LPD_UNUSED_2, START ADDRESS: FF4E0000, END ADDRESS: FF5DFFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: CRL_APB, START ADDRESS: FF5E0000, END ADDRESS: FF85FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: LPD_UNUSED_3, START ADDRESS: FF860000, END ADDRESS: FF95FFFF - // : APERTURE NAME: OCM_SLCR, START ADDRESS: FF960000, END ADDRESS: FF96FFFF - // : APERTURE NAME: LPD_UNUSED_4, START ADDRESS: FF970000, END ADDRESS: FF97FFFF - // : APERTURE NAME: LPD_XPPU, START ADDRESS: FF980000, END ADDRESS: FF99FFFF - // : APERTURE NAME: RPU, START ADDRESS: FF9A0000, END ADDRESS: FF9AFFFF - // : APERTURE NAME: AFIFM6, START ADDRESS: FF9B0000, END ADDRESS: FF9BFFFF - // : APERTURE NAME: LPD_XPPU_SINK, START ADDRESS: FF9C0000, END ADDRESS: FF9CFFFF - // : APERTURE NAME: USB3_0, START ADDRESS: FF9D0000, END ADDRESS: FF9DFFFF - // : APERTURE NAME: USB3_1, START ADDRESS: FF9E0000, END ADDRESS: FF9EFFFF - // : APERTURE NAME: LPD_UNUSED_5, START ADDRESS: FF9F0000, END ADDRESS: FF9FFFFF - // : APERTURE NAME: APM0, START ADDRESS: FFA00000, END ADDRESS: FFA0FFFF - // : APERTURE NAME: APM1, START ADDRESS: FFA10000, END ADDRESS: FFA1FFFF - // : APERTURE NAME: APM_INTC_IOU, START ADDRESS: FFA20000, END ADDRESS: FFA2FFFF - // : APERTURE NAME: APM_FPD_LPD, START ADDRESS: FFA30000, END ADDRESS: FFA3FFFF - // : APERTURE NAME: LPD_UNUSED_6, START ADDRESS: FFA40000, END ADDRESS: FFA4FFFF - // : APERTURE NAME: AMS, START ADDRESS: FFA50000, END ADDRESS: FFA5FFFF - // : APERTURE NAME: RTC, START ADDRESS: FFA60000, END ADDRESS: FFA6FFFF - // : APERTURE NAME: OCM_XMPU_CFG, START ADDRESS: FFA70000, END ADDRESS: FFA7FFFF - // : APERTURE NAME: ADMA_0, START ADDRESS: FFA80000, END ADDRESS: FFA8FFFF - // : APERTURE NAME: ADMA_1, START ADDRESS: FFA90000, END ADDRESS: FFA9FFFF - // : APERTURE NAME: ADMA_2, START ADDRESS: FFAA0000, END ADDRESS: FFAAFFFF - // : APERTURE NAME: ADMA_3, START ADDRESS: FFAB0000, END ADDRESS: FFABFFFF - // : APERTURE NAME: ADMA_4, START ADDRESS: FFAC0000, END ADDRESS: FFACFFFF - // : APERTURE NAME: ADMA_5, START ADDRESS: FFAD0000, END ADDRESS: FFADFFFF - // : APERTURE NAME: ADMA_6, START ADDRESS: FFAE0000, END ADDRESS: FFAEFFFF - // : APERTURE NAME: ADMA_7, START ADDRESS: FFAF0000, END ADDRESS: FFAFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: LPD_UNUSED_7, START ADDRESS: FFB00000, END ADDRESS: FFBFFFFF - // : APERTURE NAME: CSU_ROM, START ADDRESS: FFC00000, END ADDRESS: FFC1FFFF - // : APERTURE NAME: CSU_ROM, START ADDRESS: FFC00000, END ADDRESS: FFC1FFFF - // : APERTURE NAME: CSU_LOCAL, START ADDRESS: FFC20000, END ADDRESS: FFC2FFFF - // : APERTURE NAME: PUF, START ADDRESS: FFC30000, END ADDRESS: FFC3FFFF - // : APERTURE NAME: CSU_RAM, START ADDRESS: FFC40000, END ADDRESS: FFC5FFFF - // : APERTURE NAME: CSU_RAM, START ADDRESS: FFC40000, END ADDRESS: FFC5FFFF - // : APERTURE NAME: CSU_IOMODULE, START ADDRESS: FFC60000, END ADDRESS: FFC7FFFF - // : APERTURE NAME: CSU_IOMODULE, START ADDRESS: FFC60000, END ADDRESS: FFC7FFFF - // : APERTURE NAME: CSUDMA, START ADDRESS: FFC80000, END ADDRESS: FFC9FFFF - // : APERTURE NAME: CSUDMA, START ADDRESS: FFC80000, END ADDRESS: FFC9FFFF - // : APERTURE NAME: CSU, START ADDRESS: FFCA0000, END ADDRESS: FFCAFFFF - // : APERTURE NAME: CSU_WDT, START ADDRESS: FFCB0000, END ADDRESS: FFCBFFFF - // : APERTURE NAME: EFUSE, START ADDRESS: FFCC0000, END ADDRESS: FFCCFFFF - // : APERTURE NAME: BBRAM, START ADDRESS: FFCD0000, END ADDRESS: FFCDFFFF - // : APERTURE NAME: RSA_CORE, START ADDRESS: FFCE0000, END ADDRESS: FFCEFFFF - // : APERTURE NAME: MBISTJTAG, START ADDRESS: FFCF0000, END ADDRESS: FFCFFFFF - // : APERTURE NAME: PMU_ROM, START ADDRESS: FFD00000, END ADDRESS: FFD3FFFF - // : APERTURE NAME: PMU_ROM, START ADDRESS: FFD00000, END ADDRESS: FFD3FFFF - // : APERTURE NAME: PMU_ROM, START ADDRESS: FFD00000, END ADDRESS: FFD3FFFF - // : APERTURE NAME: PMU_ROM, START ADDRESS: FFD00000, END ADDRESS: FFD3FFFF - // : APERTURE NAME: PMU_IOMODULE, START ADDRESS: FFD40000, END ADDRESS: FFD5FFFF - // : APERTURE NAME: PMU_IOMODULE, START ADDRESS: FFD40000, END ADDRESS: FFD5FFFF - // : APERTURE NAME: PMU_LOCAL, START ADDRESS: FFD60000, END ADDRESS: FFD7FFFF - // : APERTURE NAME: PMU_LOCAL, START ADDRESS: FFD60000, END ADDRESS: FFD7FFFF - // : APERTURE NAME: PMU_GLOBAL, START ADDRESS: FFD80000, END ADDRESS: FFDBFFFF - // : APERTURE NAME: PMU_GLOBAL, START ADDRESS: FFD80000, END ADDRESS: FFDBFFFF - // : APERTURE NAME: PMU_GLOBAL, START ADDRESS: FFD80000, END ADDRESS: FFDBFFFF - // : APERTURE NAME: PMU_GLOBAL, START ADDRESS: FFD80000, END ADDRESS: FFDBFFFF - // : APERTURE NAME: PMU_RAM, START ADDRESS: FFDC0000, END ADDRESS: FFDFFFFF - // : APERTURE NAME: PMU_RAM, START ADDRESS: FFDC0000, END ADDRESS: FFDFFFFF - // : APERTURE NAME: PMU_RAM, START ADDRESS: FFDC0000, END ADDRESS: FFDFFFFF - // : APERTURE NAME: PMU_RAM, START ADDRESS: FFDC0000, END ADDRESS: FFDFFFFF - // : APERTURE NAME: R5_0_ATCM, START ADDRESS: FFE00000, END ADDRESS: FFE0FFFF - // : APERTURE NAME: R5_0_ATCM_LOCKSTEP, START ADDRESS: FFE10000, END ADDRESS: FFE1FFFF - // : APERTURE NAME: R5_0_BTCM, START ADDRESS: FFE20000, END ADDRESS: FFE2FFFF - // : APERTURE NAME: R5_0_BTCM_LOCKSTEP, START ADDRESS: FFE30000, END ADDRESS: FFE3FFFF - // : APERTURE NAME: R5_0_INSTRUCTION_CACHE, START ADDRESS: FFE40000, END ADDRESS: FFE4FFFF - // : APERTURE NAME: R5_0_DATA_CACHE, START ADDRESS: FFE50000, END ADDRESS: FFE5FFFF - // : APERTURE NAME: LPD_UNUSED_8, START ADDRESS: FFE60000, END ADDRESS: FFE8FFFF - // : APERTURE NAME: LPD_UNUSED_8, START ADDRESS: FFE60000, END ADDRESS: FFE8FFFF - // : APERTURE NAME: LPD_UNUSED_8, START ADDRESS: FFE60000, END ADDRESS: FFE8FFFF - // : APERTURE NAME: R5_1_ATCM_, START ADDRESS: FFE90000, END ADDRESS: FFE9FFFF - // : APERTURE NAME: RPU_UNUSED_10, START ADDRESS: FFEA0000, END ADDRESS: FFEAFFFF - // : APERTURE NAME: R5_1_BTCM_, START ADDRESS: FFEB0000, END ADDRESS: FFEBFFFF - // : APERTURE NAME: R5_1_INSTRUCTION_CACHE, START ADDRESS: FFEC0000, END ADDRESS: FFECFFFF - // : APERTURE NAME: R5_1_DATA_CACHE, START ADDRESS: FFED0000, END ADDRESS: FFEDFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_9, START ADDRESS: FFEE0000, END ADDRESS: FFFBFFFF - // : APERTURE NAME: LPD_UNUSED_15, START ADDRESS: FFFD0000, END ADDRESS: FFFFFFFF - // : APERTURE NAME: LPD_UNUSED_15, START ADDRESS: FFFD0000, END ADDRESS: FFFFFFFF - // : APERTURE NAME: LPD_UNUSED_15, START ADDRESS: FFFD0000, END ADDRESS: FFFFFFFF - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_256 @ 0XFF981400</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_256_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_256_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_256_PARITY 0x0 - - Entry 256 of the Aperture Permission List, for 32-byte IPI buffer 000 at BASE_32B + 0x00000000 - (OFFSET, MASK, VALUE) (0XFF981400, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_256_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_256_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_256_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_256_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_256_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_256_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_256_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_257 @ 0XFF981404</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_257_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_257_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_257_PARITY 0x0 - - Entry 257 of the Aperture Permission List, for 32-byte IPI buffer 001 at BASE_32B + 0x00000020 - (OFFSET, MASK, VALUE) (0XFF981404, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_257_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_257_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_257_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_257_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_257_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_257_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_257_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_258 @ 0XFF981408</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_258_PERMISSION 0x48 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_258_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_258_PARITY 0x0 - - Entry 258 of the Aperture Permission List, for 32-byte IPI buffer 002 at BASE_32B + 0x00000040 - (OFFSET, MASK, VALUE) (0XFF981408, 0xF80FFFFFU ,0x08000048U) - RegMask = (LPD_XPPU_CFG_APERPERM_258_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_258_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_258_PARITY_MASK | 0 ); - - RegVal = ((0x00000048U << LPD_XPPU_CFG_APERPERM_258_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_258_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_258_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_258_OFFSET ,0xF80FFFFFU ,0x08000048U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_259 @ 0XFF98140C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_259_PERMISSION 0x84 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_259_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_259_PARITY 0x0 - - Entry 259 of the Aperture Permission List, for 32-byte IPI buffer 003 at BASE_32B + 0x00000060 - (OFFSET, MASK, VALUE) (0XFF98140C, 0xF80FFFFFU ,0x08000084U) - RegMask = (LPD_XPPU_CFG_APERPERM_259_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_259_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_259_PARITY_MASK | 0 ); - - RegVal = ((0x00000084U << LPD_XPPU_CFG_APERPERM_259_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_259_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_259_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_259_OFFSET ,0xF80FFFFFU ,0x08000084U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_260 @ 0XFF981410</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_260_PERMISSION 0x41 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_260_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_260_PARITY 0x0 - - Entry 260 of the Aperture Permission List, for 32-byte IPI buffer 004 at BASE_32B + 0x00000080 - (OFFSET, MASK, VALUE) (0XFF981410, 0xF80FFFFFU ,0x08000041U) - RegMask = (LPD_XPPU_CFG_APERPERM_260_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_260_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_260_PARITY_MASK | 0 ); - - RegVal = ((0x00000041U << LPD_XPPU_CFG_APERPERM_260_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_260_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_260_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_260_OFFSET ,0xF80FFFFFU ,0x08000041U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_261 @ 0XFF981414</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_261_PERMISSION 0x14 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_261_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_261_PARITY 0x0 - - Entry 261 of the Aperture Permission List, for 32-byte IPI buffer 005 at BASE_32B + 0x000000A0 - (OFFSET, MASK, VALUE) (0XFF981414, 0xF80FFFFFU ,0x08000014U) - RegMask = (LPD_XPPU_CFG_APERPERM_261_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_261_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_261_PARITY_MASK | 0 ); - - RegVal = ((0x00000014U << LPD_XPPU_CFG_APERPERM_261_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_261_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_261_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_261_OFFSET ,0xF80FFFFFU ,0x08000014U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_262 @ 0XFF981418</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_262_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_262_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_262_PARITY 0x0 - - Entry 262 of the Aperture Permission List, for 32-byte IPI buffer 006 at BASE_32B + 0x000000C0 - (OFFSET, MASK, VALUE) (0XFF981418, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_262_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_262_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_262_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_262_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_262_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_262_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_262_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_263 @ 0XFF98141C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_263_PERMISSION 0x4 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_263_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_263_PARITY 0x0 - - Entry 263 of the Aperture Permission List, for 32-byte IPI buffer 007 at BASE_32B + 0x000000E0 - (OFFSET, MASK, VALUE) (0XFF98141C, 0xF80FFFFFU ,0x08000004U) - RegMask = (LPD_XPPU_CFG_APERPERM_263_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_263_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_263_PARITY_MASK | 0 ); - - RegVal = ((0x00000004U << LPD_XPPU_CFG_APERPERM_263_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_263_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_263_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_263_OFFSET ,0xF80FFFFFU ,0x08000004U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_264 @ 0XFF981420</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_264_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_264_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_264_PARITY 0x0 - - Entry 264 of the Aperture Permission List, for 32-byte IPI buffer 008 at BASE_32B + 0x00000100 - (OFFSET, MASK, VALUE) (0XFF981420, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_264_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_264_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_264_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_264_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_264_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_264_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_264_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_265 @ 0XFF981424</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_265_PERMISSION 0x4 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_265_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_265_PARITY 0x0 - - Entry 265 of the Aperture Permission List, for 32-byte IPI buffer 009 at BASE_32B + 0x00000120 - (OFFSET, MASK, VALUE) (0XFF981424, 0xF80FFFFFU ,0x08000004U) - RegMask = (LPD_XPPU_CFG_APERPERM_265_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_265_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_265_PARITY_MASK | 0 ); - - RegVal = ((0x00000004U << LPD_XPPU_CFG_APERPERM_265_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_265_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_265_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_265_OFFSET ,0xF80FFFFFU ,0x08000004U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_266 @ 0XFF981428</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_266_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_266_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_266_PARITY 0x0 - - Entry 266 of the Aperture Permission List, for 32-byte IPI buffer 010 at BASE_32B + 0x00000140 - (OFFSET, MASK, VALUE) (0XFF981428, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_266_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_266_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_266_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_266_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_266_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_266_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_266_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_267 @ 0XFF98142C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_267_PERMISSION 0x4 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_267_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_267_PARITY 0x0 - - Entry 267 of the Aperture Permission List, for 32-byte IPI buffer 011 at BASE_32B + 0x00000160 - (OFFSET, MASK, VALUE) (0XFF98142C, 0xF80FFFFFU ,0x08000004U) - RegMask = (LPD_XPPU_CFG_APERPERM_267_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_267_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_267_PARITY_MASK | 0 ); - - RegVal = ((0x00000004U << LPD_XPPU_CFG_APERPERM_267_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_267_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_267_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_267_OFFSET ,0xF80FFFFFU ,0x08000004U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_268 @ 0XFF981430</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_268_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_268_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_268_PARITY 0x0 - - Entry 268 of the Aperture Permission List, for 32-byte IPI buffer 012 at BASE_32B + 0x00000180 - (OFFSET, MASK, VALUE) (0XFF981430, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_268_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_268_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_268_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_268_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_268_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_268_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_268_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_269 @ 0XFF981434</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_269_PERMISSION 0x4 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_269_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_269_PARITY 0x0 - - Entry 269 of the Aperture Permission List, for 32-byte IPI buffer 013 at BASE_32B + 0x000001A0 - (OFFSET, MASK, VALUE) (0XFF981434, 0xF80FFFFFU ,0x08000004U) - RegMask = (LPD_XPPU_CFG_APERPERM_269_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_269_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_269_PARITY_MASK | 0 ); - - RegVal = ((0x00000004U << LPD_XPPU_CFG_APERPERM_269_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_269_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_269_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_269_OFFSET ,0xF80FFFFFU ,0x08000004U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_270 @ 0XFF981438</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_270_PERMISSION 0x42 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_270_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_270_PARITY 0x0 - - Entry 270 of the Aperture Permission List, for 32-byte IPI buffer 014 at BASE_32B + 0x000001C0 - (OFFSET, MASK, VALUE) (0XFF981438, 0xF80FFFFFU ,0x08000042U) - RegMask = (LPD_XPPU_CFG_APERPERM_270_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_270_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_270_PARITY_MASK | 0 ); - - RegVal = ((0x00000042U << LPD_XPPU_CFG_APERPERM_270_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_270_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_270_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_270_OFFSET ,0xF80FFFFFU ,0x08000042U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_1, START ADDRESS: FF310000, END ADDRESS: FF31FFFF - /*Register : APERPERM_271 @ 0XFF98143C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_271_PERMISSION 0x24 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_271_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_271_PARITY 0x0 - - Entry 271 of the Aperture Permission List, for 32-byte IPI buffer 015 at BASE_32B + 0x000001E0 - (OFFSET, MASK, VALUE) (0XFF98143C, 0xF80FFFFFU ,0x08000024U) - RegMask = (LPD_XPPU_CFG_APERPERM_271_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_271_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_271_PARITY_MASK | 0 ); - - RegVal = ((0x00000024U << LPD_XPPU_CFG_APERPERM_271_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_271_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_271_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_271_OFFSET ,0xF80FFFFFU ,0x08000024U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_272 @ 0XFF981440</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_272_PERMISSION 0x84 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_272_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_272_PARITY 0x0 - - Entry 272 of the Aperture Permission List, for 32-byte IPI buffer 016 at BASE_32B + 0x00000200 - (OFFSET, MASK, VALUE) (0XFF981440, 0xF80FFFFFU ,0x08000084U) - RegMask = (LPD_XPPU_CFG_APERPERM_272_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_272_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_272_PARITY_MASK | 0 ); - - RegVal = ((0x00000084U << LPD_XPPU_CFG_APERPERM_272_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_272_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_272_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_272_OFFSET ,0xF80FFFFFU ,0x08000084U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_273 @ 0XFF981444</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_273_PERMISSION 0x48 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_273_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_273_PARITY 0x0 - - Entry 273 of the Aperture Permission List, for 32-byte IPI buffer 017 at BASE_32B + 0x00000220 - (OFFSET, MASK, VALUE) (0XFF981444, 0xF80FFFFFU ,0x08000048U) - RegMask = (LPD_XPPU_CFG_APERPERM_273_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_273_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_273_PARITY_MASK | 0 ); - - RegVal = ((0x00000048U << LPD_XPPU_CFG_APERPERM_273_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_273_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_273_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_273_OFFSET ,0xF80FFFFFU ,0x08000048U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_274 @ 0XFF981448</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_274_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_274_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_274_PARITY 0x0 - - Entry 274 of the Aperture Permission List, for 32-byte IPI buffer 018 at BASE_32B + 0x00000240 - (OFFSET, MASK, VALUE) (0XFF981448, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_274_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_274_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_274_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_274_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_274_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_274_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_274_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_275 @ 0XFF98144C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_275_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_275_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_275_PARITY 0x0 - - Entry 275 of the Aperture Permission List, for 32-byte IPI buffer 019 at BASE_32B + 0x00000260 - (OFFSET, MASK, VALUE) (0XFF98144C, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_275_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_275_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_275_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_275_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_275_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_275_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_275_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_276 @ 0XFF981450</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_276_PERMISSION 0x81 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_276_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_276_PARITY 0x0 - - Entry 276 of the Aperture Permission List, for 32-byte IPI buffer 020 at BASE_32B + 0x00000280 - (OFFSET, MASK, VALUE) (0XFF981450, 0xF80FFFFFU ,0x08000081U) - RegMask = (LPD_XPPU_CFG_APERPERM_276_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_276_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_276_PARITY_MASK | 0 ); - - RegVal = ((0x00000081U << LPD_XPPU_CFG_APERPERM_276_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_276_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_276_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_276_OFFSET ,0xF80FFFFFU ,0x08000081U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_277 @ 0XFF981454</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_277_PERMISSION 0x18 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_277_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_277_PARITY 0x0 - - Entry 277 of the Aperture Permission List, for 32-byte IPI buffer 021 at BASE_32B + 0x000002A0 - (OFFSET, MASK, VALUE) (0XFF981454, 0xF80FFFFFU ,0x08000018U) - RegMask = (LPD_XPPU_CFG_APERPERM_277_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_277_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_277_PARITY_MASK | 0 ); - - RegVal = ((0x00000018U << LPD_XPPU_CFG_APERPERM_277_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_277_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_277_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_277_OFFSET ,0xF80FFFFFU ,0x08000018U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_278 @ 0XFF981458</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_278_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_278_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_278_PARITY 0x0 - - Entry 278 of the Aperture Permission List, for 32-byte IPI buffer 022 at BASE_32B + 0x000002C0 - (OFFSET, MASK, VALUE) (0XFF981458, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_278_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_278_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_278_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_278_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_278_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_278_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_278_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_279 @ 0XFF98145C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_279_PERMISSION 0x8 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_279_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_279_PARITY 0x0 - - Entry 279 of the Aperture Permission List, for 32-byte IPI buffer 023 at BASE_32B + 0x000002E0 - (OFFSET, MASK, VALUE) (0XFF98145C, 0xF80FFFFFU ,0x08000008U) - RegMask = (LPD_XPPU_CFG_APERPERM_279_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_279_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_279_PARITY_MASK | 0 ); - - RegVal = ((0x00000008U << LPD_XPPU_CFG_APERPERM_279_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_279_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_279_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_279_OFFSET ,0xF80FFFFFU ,0x08000008U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_280 @ 0XFF981460</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_280_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_280_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_280_PARITY 0x0 - - Entry 280 of the Aperture Permission List, for 32-byte IPI buffer 024 at BASE_32B + 0x00000300 - (OFFSET, MASK, VALUE) (0XFF981460, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_280_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_280_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_280_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_280_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_280_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_280_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_280_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_281 @ 0XFF981464</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_281_PERMISSION 0x8 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_281_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_281_PARITY 0x0 - - Entry 281 of the Aperture Permission List, for 32-byte IPI buffer 025 at BASE_32B + 0x00000320 - (OFFSET, MASK, VALUE) (0XFF981464, 0xF80FFFFFU ,0x08000008U) - RegMask = (LPD_XPPU_CFG_APERPERM_281_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_281_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_281_PARITY_MASK | 0 ); - - RegVal = ((0x00000008U << LPD_XPPU_CFG_APERPERM_281_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_281_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_281_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_281_OFFSET ,0xF80FFFFFU ,0x08000008U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_282 @ 0XFF981468</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_282_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_282_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_282_PARITY 0x0 - - Entry 282 of the Aperture Permission List, for 32-byte IPI buffer 026 at BASE_32B + 0x00000340 - (OFFSET, MASK, VALUE) (0XFF981468, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_282_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_282_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_282_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_282_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_282_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_282_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_282_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_283 @ 0XFF98146C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_283_PERMISSION 0x8 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_283_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_283_PARITY 0x0 - - Entry 283 of the Aperture Permission List, for 32-byte IPI buffer 027 at BASE_32B + 0x00000360 - (OFFSET, MASK, VALUE) (0XFF98146C, 0xF80FFFFFU ,0x08000008U) - RegMask = (LPD_XPPU_CFG_APERPERM_283_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_283_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_283_PARITY_MASK | 0 ); - - RegVal = ((0x00000008U << LPD_XPPU_CFG_APERPERM_283_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_283_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_283_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_283_OFFSET ,0xF80FFFFFU ,0x08000008U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_284 @ 0XFF981470</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_284_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_284_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_284_PARITY 0x0 - - Entry 284 of the Aperture Permission List, for 32-byte IPI buffer 028 at BASE_32B + 0x00000380 - (OFFSET, MASK, VALUE) (0XFF981470, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_284_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_284_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_284_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_284_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_284_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_284_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_284_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_285 @ 0XFF981474</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_285_PERMISSION 0x8 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_285_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_285_PARITY 0x0 - - Entry 285 of the Aperture Permission List, for 32-byte IPI buffer 029 at BASE_32B + 0x000003A0 - (OFFSET, MASK, VALUE) (0XFF981474, 0xF80FFFFFU ,0x08000008U) - RegMask = (LPD_XPPU_CFG_APERPERM_285_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_285_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_285_PARITY_MASK | 0 ); - - RegVal = ((0x00000008U << LPD_XPPU_CFG_APERPERM_285_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_285_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_285_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_285_OFFSET ,0xF80FFFFFU ,0x08000008U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_286 @ 0XFF981478</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_286_PERMISSION 0x82 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_286_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_286_PARITY 0x0 - - Entry 286 of the Aperture Permission List, for 32-byte IPI buffer 030 at BASE_32B + 0x000003C0 - (OFFSET, MASK, VALUE) (0XFF981478, 0xF80FFFFFU ,0x08000082U) - RegMask = (LPD_XPPU_CFG_APERPERM_286_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_286_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_286_PARITY_MASK | 0 ); - - RegVal = ((0x00000082U << LPD_XPPU_CFG_APERPERM_286_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_286_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_286_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_286_OFFSET ,0xF80FFFFFU ,0x08000082U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_2, START ADDRESS: FF320000, END ADDRESS: FF32FFFF - /*Register : APERPERM_287 @ 0XFF98147C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_287_PERMISSION 0x28 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_287_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_287_PARITY 0x0 - - Entry 287 of the Aperture Permission List, for 32-byte IPI buffer 031 at BASE_32B + 0x000003E0 - (OFFSET, MASK, VALUE) (0XFF98147C, 0xF80FFFFFU ,0x08000028U) - RegMask = (LPD_XPPU_CFG_APERPERM_287_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_287_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_287_PARITY_MASK | 0 ); - - RegVal = ((0x00000028U << LPD_XPPU_CFG_APERPERM_287_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_287_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_287_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_287_OFFSET ,0xF80FFFFFU ,0x08000028U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_288 @ 0XFF981480</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_288_PERMISSION 0x14 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_288_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_288_PARITY 0x0 - - Entry 288 of the Aperture Permission List, for 32-byte IPI buffer 032 at BASE_32B + 0x00000400 - (OFFSET, MASK, VALUE) (0XFF981480, 0xF80FFFFFU ,0x08000014U) - RegMask = (LPD_XPPU_CFG_APERPERM_288_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_288_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_288_PARITY_MASK | 0 ); - - RegVal = ((0x00000014U << LPD_XPPU_CFG_APERPERM_288_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_288_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_288_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_288_OFFSET ,0xF80FFFFFU ,0x08000014U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_289 @ 0XFF981484</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_289_PERMISSION 0x41 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_289_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_289_PARITY 0x0 - - Entry 289 of the Aperture Permission List, for 32-byte IPI buffer 033 at BASE_32B + 0x00000420 - (OFFSET, MASK, VALUE) (0XFF981484, 0xF80FFFFFU ,0x08000041U) - RegMask = (LPD_XPPU_CFG_APERPERM_289_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_289_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_289_PARITY_MASK | 0 ); - - RegVal = ((0x00000041U << LPD_XPPU_CFG_APERPERM_289_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_289_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_289_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_289_OFFSET ,0xF80FFFFFU ,0x08000041U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_290 @ 0XFF981488</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_290_PERMISSION 0x18 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_290_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_290_PARITY 0x0 - - Entry 290 of the Aperture Permission List, for 32-byte IPI buffer 034 at BASE_32B + 0x00000440 - (OFFSET, MASK, VALUE) (0XFF981488, 0xF80FFFFFU ,0x08000018U) - RegMask = (LPD_XPPU_CFG_APERPERM_290_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_290_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_290_PARITY_MASK | 0 ); - - RegVal = ((0x00000018U << LPD_XPPU_CFG_APERPERM_290_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_290_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_290_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_290_OFFSET ,0xF80FFFFFU ,0x08000018U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_291 @ 0XFF98148C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_291_PERMISSION 0x81 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_291_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_291_PARITY 0x0 - - Entry 291 of the Aperture Permission List, for 32-byte IPI buffer 035 at BASE_32B + 0x00000460 - (OFFSET, MASK, VALUE) (0XFF98148C, 0xF80FFFFFU ,0x08000081U) - RegMask = (LPD_XPPU_CFG_APERPERM_291_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_291_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_291_PARITY_MASK | 0 ); - - RegVal = ((0x00000081U << LPD_XPPU_CFG_APERPERM_291_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_291_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_291_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_291_OFFSET ,0xF80FFFFFU ,0x08000081U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_292 @ 0XFF981490</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_292_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_292_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_292_PARITY 0x0 - - Entry 292 of the Aperture Permission List, for 32-byte IPI buffer 036 at BASE_32B + 0x00000480 - (OFFSET, MASK, VALUE) (0XFF981490, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_292_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_292_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_292_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_292_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_292_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_292_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_292_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_293 @ 0XFF981494</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_293_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_293_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_293_PARITY 0x0 - - Entry 293 of the Aperture Permission List, for 32-byte IPI buffer 037 at BASE_32B + 0x000004A0 - (OFFSET, MASK, VALUE) (0XFF981494, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_293_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_293_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_293_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_293_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_293_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_293_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_293_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_294 @ 0XFF981498</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_294_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_294_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_294_PARITY 0x0 - - Entry 294 of the Aperture Permission List, for 32-byte IPI buffer 038 at BASE_32B + 0x000004C0 - (OFFSET, MASK, VALUE) (0XFF981498, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_294_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_294_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_294_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_294_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_294_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_294_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_294_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_295 @ 0XFF98149C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_295_PERMISSION 0x1 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_295_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_295_PARITY 0x0 - - Entry 295 of the Aperture Permission List, for 32-byte IPI buffer 039 at BASE_32B + 0x000004E0 - (OFFSET, MASK, VALUE) (0XFF98149C, 0xF80FFFFFU ,0x08000001U) - RegMask = (LPD_XPPU_CFG_APERPERM_295_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_295_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_295_PARITY_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_APERPERM_295_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_295_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_295_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_295_OFFSET ,0xF80FFFFFU ,0x08000001U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_296 @ 0XFF9814A0</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_296_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_296_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_296_PARITY 0x0 - - Entry 296 of the Aperture Permission List, for 32-byte IPI buffer 040 at BASE_32B + 0x00000500 - (OFFSET, MASK, VALUE) (0XFF9814A0, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_296_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_296_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_296_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_296_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_296_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_296_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_296_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_297 @ 0XFF9814A4</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_297_PERMISSION 0x1 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_297_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_297_PARITY 0x0 - - Entry 297 of the Aperture Permission List, for 32-byte IPI buffer 041 at BASE_32B + 0x00000520 - (OFFSET, MASK, VALUE) (0XFF9814A4, 0xF80FFFFFU ,0x08000001U) - RegMask = (LPD_XPPU_CFG_APERPERM_297_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_297_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_297_PARITY_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_APERPERM_297_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_297_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_297_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_297_OFFSET ,0xF80FFFFFU ,0x08000001U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_298 @ 0XFF9814A8</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_298_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_298_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_298_PARITY 0x0 - - Entry 298 of the Aperture Permission List, for 32-byte IPI buffer 042 at BASE_32B + 0x00000540 - (OFFSET, MASK, VALUE) (0XFF9814A8, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_298_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_298_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_298_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_298_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_298_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_298_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_298_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_299 @ 0XFF9814AC</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_299_PERMISSION 0x1 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_299_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_299_PARITY 0x0 - - Entry 299 of the Aperture Permission List, for 32-byte IPI buffer 043 at BASE_32B + 0x00000560 - (OFFSET, MASK, VALUE) (0XFF9814AC, 0xF80FFFFFU ,0x08000001U) - RegMask = (LPD_XPPU_CFG_APERPERM_299_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_299_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_299_PARITY_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_APERPERM_299_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_299_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_299_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_299_OFFSET ,0xF80FFFFFU ,0x08000001U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_300 @ 0XFF9814B0</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_300_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_300_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_300_PARITY 0x0 - - Entry 300 of the Aperture Permission List, for 32-byte IPI buffer 044 at BASE_32B + 0x00000580 - (OFFSET, MASK, VALUE) (0XFF9814B0, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_300_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_300_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_300_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_300_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_300_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_300_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_300_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_301 @ 0XFF9814B4</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_301_PERMISSION 0x1 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_301_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_301_PARITY 0x0 - - Entry 301 of the Aperture Permission List, for 32-byte IPI buffer 045 at BASE_32B + 0x000005A0 - (OFFSET, MASK, VALUE) (0XFF9814B4, 0xF80FFFFFU ,0x08000001U) - RegMask = (LPD_XPPU_CFG_APERPERM_301_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_301_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_301_PARITY_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_APERPERM_301_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_301_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_301_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_301_OFFSET ,0xF80FFFFFU ,0x08000001U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_302 @ 0XFF9814B8</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_302_PERMISSION 0x12 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_302_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_302_PARITY 0x0 - - Entry 302 of the Aperture Permission List, for 32-byte IPI buffer 046 at BASE_32B + 0x000005C0 - (OFFSET, MASK, VALUE) (0XFF9814B8, 0xF80FFFFFU ,0x08000012U) - RegMask = (LPD_XPPU_CFG_APERPERM_302_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_302_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_302_PARITY_MASK | 0 ); - - RegVal = ((0x00000012U << LPD_XPPU_CFG_APERPERM_302_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_302_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_302_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_302_OFFSET ,0xF80FFFFFU ,0x08000012U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_0, START ADDRESS: FF300000, END ADDRESS: FF30FFFF - /*Register : APERPERM_303 @ 0XFF9814BC</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_303_PERMISSION 0x21 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_303_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_303_PARITY 0x0 - - Entry 303 of the Aperture Permission List, for 32-byte IPI buffer 047 at BASE_32B + 0x000005E0 - (OFFSET, MASK, VALUE) (0XFF9814BC, 0xF80FFFFFU ,0x08000021U) - RegMask = (LPD_XPPU_CFG_APERPERM_303_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_303_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_303_PARITY_MASK | 0 ); - - RegVal = ((0x00000021U << LPD_XPPU_CFG_APERPERM_303_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_303_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_303_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_303_OFFSET ,0xF80FFFFFU ,0x08000021U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - /*Register : APERPERM_304 @ 0XFF9814C0</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_304_PERMISSION 0x4 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_304_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_304_PARITY 0x0 - - Entry 304 of the Aperture Permission List, for 32-byte IPI buffer 048 at BASE_32B + 0x00000600 - (OFFSET, MASK, VALUE) (0XFF9814C0, 0xF80FFFFFU ,0x08000004U) - RegMask = (LPD_XPPU_CFG_APERPERM_304_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_304_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_304_PARITY_MASK | 0 ); - - RegVal = ((0x00000004U << LPD_XPPU_CFG_APERPERM_304_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_304_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_304_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_304_OFFSET ,0xF80FFFFFU ,0x08000004U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - /*Register : APERPERM_305 @ 0XFF9814C4</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_305_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_305_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_305_PARITY 0x0 - - Entry 305 of the Aperture Permission List, for 32-byte IPI buffer 049 at BASE_32B + 0x00000620 - (OFFSET, MASK, VALUE) (0XFF9814C4, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_305_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_305_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_305_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_305_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_305_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_305_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_305_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - /*Register : APERPERM_306 @ 0XFF9814C8</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_306_PERMISSION 0x8 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_306_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_306_PARITY 0x0 - - Entry 306 of the Aperture Permission List, for 32-byte IPI buffer 050 at BASE_32B + 0x00000640 - (OFFSET, MASK, VALUE) (0XFF9814C8, 0xF80FFFFFU ,0x08000008U) - RegMask = (LPD_XPPU_CFG_APERPERM_306_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_306_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_306_PARITY_MASK | 0 ); - - RegVal = ((0x00000008U << LPD_XPPU_CFG_APERPERM_306_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_306_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_306_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_306_OFFSET ,0xF80FFFFFU ,0x08000008U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - /*Register : APERPERM_307 @ 0XFF9814CC</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_307_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_307_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_307_PARITY 0x0 - - Entry 307 of the Aperture Permission List, for 32-byte IPI buffer 051 at BASE_32B + 0x00000660 - (OFFSET, MASK, VALUE) (0XFF9814CC, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_307_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_307_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_307_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_307_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_307_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_307_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_307_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - /*Register : APERPERM_308 @ 0XFF9814D0</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_308_PERMISSION 0x1 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_308_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_308_PARITY 0x0 - - Entry 308 of the Aperture Permission List, for 32-byte IPI buffer 052 at BASE_32B + 0x00000680 - (OFFSET, MASK, VALUE) (0XFF9814D0, 0xF80FFFFFU ,0x08000001U) - RegMask = (LPD_XPPU_CFG_APERPERM_308_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_308_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_308_PARITY_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_APERPERM_308_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_308_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_308_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_308_OFFSET ,0xF80FFFFFU ,0x08000001U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - /*Register : APERPERM_309 @ 0XFF9814D4</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_309_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_309_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_309_PARITY 0x0 - - Entry 309 of the Aperture Permission List, for 32-byte IPI buffer 053 at BASE_32B + 0x000006A0 - (OFFSET, MASK, VALUE) (0XFF9814D4, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_309_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_309_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_309_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_309_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_309_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_309_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_309_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - /*Register : APERPERM_318 @ 0XFF9814F8</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_318_PERMISSION 0x2 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_318_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_318_PARITY 0x0 - - Entry 318 of the Aperture Permission List, for 32-byte IPI buffer 062 at BASE_32B + 0x000007C0 - (OFFSET, MASK, VALUE) (0XFF9814F8, 0xF80FFFFFU ,0x08000002U) - RegMask = (LPD_XPPU_CFG_APERPERM_318_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_318_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_318_PARITY_MASK | 0 ); - - RegVal = ((0x00000002U << LPD_XPPU_CFG_APERPERM_318_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_318_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_318_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_318_OFFSET ,0xF80FFFFFU ,0x08000002U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_7, START ADDRESS: FF340000, END ADDRESS: FF34FFFF - /*Register : APERPERM_319 @ 0XFF9814FC</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_319_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_319_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_319_PARITY 0x0 - - Entry 319 of the Aperture Permission List, for 32-byte IPI buffer 063 at BASE_32B + 0x000007E0 - (OFFSET, MASK, VALUE) (0XFF9814FC, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_319_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_319_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_319_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_319_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_319_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_319_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_319_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - /*Register : APERPERM_320 @ 0XFF981500</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_320_PERMISSION 0x4 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_320_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_320_PARITY 0x0 - - Entry 320 of the Aperture Permission List, for 32-byte IPI buffer 064 at BASE_32B + 0x00000800 - (OFFSET, MASK, VALUE) (0XFF981500, 0xF80FFFFFU ,0x08000004U) - RegMask = (LPD_XPPU_CFG_APERPERM_320_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_320_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_320_PARITY_MASK | 0 ); - - RegVal = ((0x00000004U << LPD_XPPU_CFG_APERPERM_320_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_320_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_320_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_320_OFFSET ,0xF80FFFFFU ,0x08000004U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - /*Register : APERPERM_321 @ 0XFF981504</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_321_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_321_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_321_PARITY 0x0 - - Entry 321 of the Aperture Permission List, for 32-byte IPI buffer 065 at BASE_32B + 0x00000820 - (OFFSET, MASK, VALUE) (0XFF981504, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_321_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_321_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_321_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_321_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_321_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_321_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_321_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - /*Register : APERPERM_322 @ 0XFF981508</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_322_PERMISSION 0x8 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_322_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_322_PARITY 0x0 - - Entry 322 of the Aperture Permission List, for 32-byte IPI buffer 066 at BASE_32B + 0x00000840 - (OFFSET, MASK, VALUE) (0XFF981508, 0xF80FFFFFU ,0x08000008U) - RegMask = (LPD_XPPU_CFG_APERPERM_322_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_322_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_322_PARITY_MASK | 0 ); - - RegVal = ((0x00000008U << LPD_XPPU_CFG_APERPERM_322_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_322_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_322_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_322_OFFSET ,0xF80FFFFFU ,0x08000008U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - /*Register : APERPERM_323 @ 0XFF98150C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_323_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_323_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_323_PARITY 0x0 - - Entry 323 of the Aperture Permission List, for 32-byte IPI buffer 067 at BASE_32B + 0x00000860 - (OFFSET, MASK, VALUE) (0XFF98150C, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_323_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_323_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_323_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_323_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_323_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_323_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_323_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - /*Register : APERPERM_324 @ 0XFF981510</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_324_PERMISSION 0x1 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_324_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_324_PARITY 0x0 - - Entry 324 of the Aperture Permission List, for 32-byte IPI buffer 068 at BASE_32B + 0x00000880 - (OFFSET, MASK, VALUE) (0XFF981510, 0xF80FFFFFU ,0x08000001U) - RegMask = (LPD_XPPU_CFG_APERPERM_324_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_324_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_324_PARITY_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_APERPERM_324_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_324_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_324_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_324_OFFSET ,0xF80FFFFFU ,0x08000001U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - /*Register : APERPERM_325 @ 0XFF981514</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_325_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_325_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_325_PARITY 0x0 - - Entry 325 of the Aperture Permission List, for 32-byte IPI buffer 069 at BASE_32B + 0x000008A0 - (OFFSET, MASK, VALUE) (0XFF981514, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_325_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_325_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_325_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_325_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_325_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_325_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_325_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - /*Register : APERPERM_334 @ 0XFF981538</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_334_PERMISSION 0x2 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_334_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_334_PARITY 0x0 - - Entry 334 of the Aperture Permission List, for 32-byte IPI buffer 078 at BASE_32B + 0x000009C0 - (OFFSET, MASK, VALUE) (0XFF981538, 0xF80FFFFFU ,0x08000002U) - RegMask = (LPD_XPPU_CFG_APERPERM_334_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_334_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_334_PARITY_MASK | 0 ); - - RegVal = ((0x00000002U << LPD_XPPU_CFG_APERPERM_334_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_334_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_334_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_334_OFFSET ,0xF80FFFFFU ,0x08000002U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_8, START ADDRESS: FF350000, END ADDRESS: FF35FFFF - /*Register : APERPERM_335 @ 0XFF98153C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_335_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_335_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_335_PARITY 0x0 - - Entry 335 of the Aperture Permission List, for 32-byte IPI buffer 079 at BASE_32B + 0x000009E0 - (OFFSET, MASK, VALUE) (0XFF98153C, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_335_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_335_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_335_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_335_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_335_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_335_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_335_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - /*Register : APERPERM_336 @ 0XFF981540</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_336_PERMISSION 0x4 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_336_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_336_PARITY 0x0 - - Entry 336 of the Aperture Permission List, for 32-byte IPI buffer 080 at BASE_32B + 0x00000A00 - (OFFSET, MASK, VALUE) (0XFF981540, 0xF80FFFFFU ,0x08000004U) - RegMask = (LPD_XPPU_CFG_APERPERM_336_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_336_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_336_PARITY_MASK | 0 ); - - RegVal = ((0x00000004U << LPD_XPPU_CFG_APERPERM_336_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_336_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_336_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_336_OFFSET ,0xF80FFFFFU ,0x08000004U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - /*Register : APERPERM_337 @ 0XFF981544</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_337_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_337_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_337_PARITY 0x0 - - Entry 337 of the Aperture Permission List, for 32-byte IPI buffer 081 at BASE_32B + 0x00000A20 - (OFFSET, MASK, VALUE) (0XFF981544, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_337_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_337_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_337_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_337_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_337_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_337_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_337_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - /*Register : APERPERM_338 @ 0XFF981548</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_338_PERMISSION 0x8 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_338_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_338_PARITY 0x0 - - Entry 338 of the Aperture Permission List, for 32-byte IPI buffer 082 at BASE_32B + 0x00000A40 - (OFFSET, MASK, VALUE) (0XFF981548, 0xF80FFFFFU ,0x08000008U) - RegMask = (LPD_XPPU_CFG_APERPERM_338_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_338_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_338_PARITY_MASK | 0 ); - - RegVal = ((0x00000008U << LPD_XPPU_CFG_APERPERM_338_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_338_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_338_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_338_OFFSET ,0xF80FFFFFU ,0x08000008U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - /*Register : APERPERM_339 @ 0XFF98154C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_339_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_339_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_339_PARITY 0x0 - - Entry 339 of the Aperture Permission List, for 32-byte IPI buffer 083 at BASE_32B + 0x00000A60 - (OFFSET, MASK, VALUE) (0XFF98154C, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_339_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_339_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_339_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_339_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_339_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_339_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_339_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - /*Register : APERPERM_340 @ 0XFF981550</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_340_PERMISSION 0x1 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_340_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_340_PARITY 0x0 - - Entry 340 of the Aperture Permission List, for 32-byte IPI buffer 084 at BASE_32B + 0x00000A80 - (OFFSET, MASK, VALUE) (0XFF981550, 0xF80FFFFFU ,0x08000001U) - RegMask = (LPD_XPPU_CFG_APERPERM_340_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_340_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_340_PARITY_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_APERPERM_340_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_340_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_340_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_340_OFFSET ,0xF80FFFFFU ,0x08000001U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - /*Register : APERPERM_341 @ 0XFF981554</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_341_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_341_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_341_PARITY 0x0 - - Entry 341 of the Aperture Permission List, for 32-byte IPI buffer 085 at BASE_32B + 0x00000AA0 - (OFFSET, MASK, VALUE) (0XFF981554, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_341_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_341_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_341_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_341_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_341_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_341_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_341_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - /*Register : APERPERM_350 @ 0XFF981578</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_350_PERMISSION 0x2 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_350_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_350_PARITY 0x0 - - Entry 350 of the Aperture Permission List, for 32-byte IPI buffer 094 at BASE_32B + 0x00000BC0 - (OFFSET, MASK, VALUE) (0XFF981578, 0xF80FFFFFU ,0x08000002U) - RegMask = (LPD_XPPU_CFG_APERPERM_350_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_350_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_350_PARITY_MASK | 0 ); - - RegVal = ((0x00000002U << LPD_XPPU_CFG_APERPERM_350_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_350_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_350_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_350_OFFSET ,0xF80FFFFFU ,0x08000002U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_9, START ADDRESS: FF360000, END ADDRESS: FF36FFFF - /*Register : APERPERM_351 @ 0XFF98157C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_351_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_351_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_351_PARITY 0x0 - - Entry 351 of the Aperture Permission List, for 32-byte IPI buffer 095 at BASE_32B + 0x00000BE0 - (OFFSET, MASK, VALUE) (0XFF98157C, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_351_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_351_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_351_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_351_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_351_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_351_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_351_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - /*Register : APERPERM_352 @ 0XFF981580</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_352_PERMISSION 0x4 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_352_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_352_PARITY 0x0 - - Entry 352 of the Aperture Permission List, for 32-byte IPI buffer 096 at BASE_32B + 0x00000C00 - (OFFSET, MASK, VALUE) (0XFF981580, 0xF80FFFFFU ,0x08000004U) - RegMask = (LPD_XPPU_CFG_APERPERM_352_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_352_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_352_PARITY_MASK | 0 ); - - RegVal = ((0x00000004U << LPD_XPPU_CFG_APERPERM_352_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_352_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_352_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_352_OFFSET ,0xF80FFFFFU ,0x08000004U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - /*Register : APERPERM_353 @ 0XFF981584</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_353_PERMISSION 0x40 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_353_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_353_PARITY 0x0 - - Entry 353 of the Aperture Permission List, for 32-byte IPI buffer 097 at BASE_32B + 0x00000C20 - (OFFSET, MASK, VALUE) (0XFF981584, 0xF80FFFFFU ,0x08000040U) - RegMask = (LPD_XPPU_CFG_APERPERM_353_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_353_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_353_PARITY_MASK | 0 ); - - RegVal = ((0x00000040U << LPD_XPPU_CFG_APERPERM_353_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_353_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_353_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_353_OFFSET ,0xF80FFFFFU ,0x08000040U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - /*Register : APERPERM_354 @ 0XFF981588</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_354_PERMISSION 0x8 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_354_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_354_PARITY 0x0 - - Entry 354 of the Aperture Permission List, for 32-byte IPI buffer 098 at BASE_32B + 0x00000C40 - (OFFSET, MASK, VALUE) (0XFF981588, 0xF80FFFFFU ,0x08000008U) - RegMask = (LPD_XPPU_CFG_APERPERM_354_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_354_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_354_PARITY_MASK | 0 ); - - RegVal = ((0x00000008U << LPD_XPPU_CFG_APERPERM_354_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_354_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_354_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_354_OFFSET ,0xF80FFFFFU ,0x08000008U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - /*Register : APERPERM_355 @ 0XFF98158C</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_355_PERMISSION 0x80 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_355_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_355_PARITY 0x0 - - Entry 355 of the Aperture Permission List, for 32-byte IPI buffer 099 at BASE_32B + 0x00000C60 - (OFFSET, MASK, VALUE) (0XFF98158C, 0xF80FFFFFU ,0x08000080U) - RegMask = (LPD_XPPU_CFG_APERPERM_355_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_355_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_355_PARITY_MASK | 0 ); - - RegVal = ((0x00000080U << LPD_XPPU_CFG_APERPERM_355_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_355_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_355_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_355_OFFSET ,0xF80FFFFFU ,0x08000080U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - /*Register : APERPERM_356 @ 0XFF981590</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_356_PERMISSION 0x1 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_356_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_356_PARITY 0x0 - - Entry 356 of the Aperture Permission List, for 32-byte IPI buffer 100 at BASE_32B + 0x00000C80 - (OFFSET, MASK, VALUE) (0XFF981590, 0xF80FFFFFU ,0x08000001U) - RegMask = (LPD_XPPU_CFG_APERPERM_356_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_356_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_356_PARITY_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_APERPERM_356_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_356_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_356_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_356_OFFSET ,0xF80FFFFFU ,0x08000001U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - /*Register : APERPERM_357 @ 0XFF981594</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_357_PERMISSION 0x10 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_357_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_357_PARITY 0x0 - - Entry 357 of the Aperture Permission List, for 32-byte IPI buffer 101 at BASE_32B + 0x00000CA0 - (OFFSET, MASK, VALUE) (0XFF981594, 0xF80FFFFFU ,0x08000010U) - RegMask = (LPD_XPPU_CFG_APERPERM_357_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_357_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_357_PARITY_MASK | 0 ); - - RegVal = ((0x00000010U << LPD_XPPU_CFG_APERPERM_357_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_357_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_357_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_357_OFFSET ,0xF80FFFFFU ,0x08000010U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - /*Register : APERPERM_366 @ 0XFF9815B8</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_366_PERMISSION 0x2 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_366_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_366_PARITY 0x0 - - Entry 366 of the Aperture Permission List, for 32-byte IPI buffer 110 at BASE_32B + 0x00000DC0 - (OFFSET, MASK, VALUE) (0XFF9815B8, 0xF80FFFFFU ,0x08000002U) - RegMask = (LPD_XPPU_CFG_APERPERM_366_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_366_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_366_PARITY_MASK | 0 ); - - RegVal = ((0x00000002U << LPD_XPPU_CFG_APERPERM_366_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_366_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_366_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_366_OFFSET ,0xF80FFFFFU ,0x08000002U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_10, START ADDRESS: FF370000, END ADDRESS: FF37FFFF - /*Register : APERPERM_367 @ 0XFF9815BC</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_367_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_367_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_367_PARITY 0x0 - - Entry 367 of the Aperture Permission List, for 32-byte IPI buffer 111 at BASE_32B + 0x00000DE0 - (OFFSET, MASK, VALUE) (0XFF9815BC, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_367_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_367_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_367_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_367_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_367_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_367_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_367_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_368 @ 0XFF9815C0</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_368_PERMISSION 0x24 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_368_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_368_PARITY 0x0 - - Entry 368 of the Aperture Permission List, for 32-byte IPI buffer 112 at BASE_32B + 0x00000E00 - (OFFSET, MASK, VALUE) (0XFF9815C0, 0xF80FFFFFU ,0x08000024U) - RegMask = (LPD_XPPU_CFG_APERPERM_368_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_368_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_368_PARITY_MASK | 0 ); - - RegVal = ((0x00000024U << LPD_XPPU_CFG_APERPERM_368_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_368_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_368_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_368_OFFSET ,0xF80FFFFFU ,0x08000024U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_369 @ 0XFF9815C4</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_369_PERMISSION 0x42 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_369_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_369_PARITY 0x0 - - Entry 369 of the Aperture Permission List, for 32-byte IPI buffer 113 at BASE_32B + 0x00000E20 - (OFFSET, MASK, VALUE) (0XFF9815C4, 0xF80FFFFFU ,0x08000042U) - RegMask = (LPD_XPPU_CFG_APERPERM_369_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_369_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_369_PARITY_MASK | 0 ); - - RegVal = ((0x00000042U << LPD_XPPU_CFG_APERPERM_369_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_369_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_369_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_369_OFFSET ,0xF80FFFFFU ,0x08000042U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_370 @ 0XFF9815C8</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_370_PERMISSION 0x28 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_370_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_370_PARITY 0x0 - - Entry 370 of the Aperture Permission List, for 32-byte IPI buffer 114 at BASE_32B + 0x00000E40 - (OFFSET, MASK, VALUE) (0XFF9815C8, 0xF80FFFFFU ,0x08000028U) - RegMask = (LPD_XPPU_CFG_APERPERM_370_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_370_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_370_PARITY_MASK | 0 ); - - RegVal = ((0x00000028U << LPD_XPPU_CFG_APERPERM_370_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_370_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_370_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_370_OFFSET ,0xF80FFFFFU ,0x08000028U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_371 @ 0XFF9815CC</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_371_PERMISSION 0x82 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_371_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_371_PARITY 0x0 - - Entry 371 of the Aperture Permission List, for 32-byte IPI buffer 115 at BASE_32B + 0x00000E60 - (OFFSET, MASK, VALUE) (0XFF9815CC, 0xF80FFFFFU ,0x08000082U) - RegMask = (LPD_XPPU_CFG_APERPERM_371_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_371_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_371_PARITY_MASK | 0 ); - - RegVal = ((0x00000082U << LPD_XPPU_CFG_APERPERM_371_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_371_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_371_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_371_OFFSET ,0xF80FFFFFU ,0x08000082U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_372 @ 0XFF9815D0</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_372_PERMISSION 0x21 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_372_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_372_PARITY 0x0 - - Entry 372 of the Aperture Permission List, for 32-byte IPI buffer 116 at BASE_32B + 0x00000E80 - (OFFSET, MASK, VALUE) (0XFF9815D0, 0xF80FFFFFU ,0x08000021U) - RegMask = (LPD_XPPU_CFG_APERPERM_372_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_372_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_372_PARITY_MASK | 0 ); - - RegVal = ((0x00000021U << LPD_XPPU_CFG_APERPERM_372_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_372_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_372_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_372_OFFSET ,0xF80FFFFFU ,0x08000021U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_373 @ 0XFF9815D4</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_373_PERMISSION 0x12 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_373_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_373_PARITY 0x0 - - Entry 373 of the Aperture Permission List, for 32-byte IPI buffer 117 at BASE_32B + 0x00000EA0 - (OFFSET, MASK, VALUE) (0XFF9815D4, 0xF80FFFFFU ,0x08000012U) - RegMask = (LPD_XPPU_CFG_APERPERM_373_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_373_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_373_PARITY_MASK | 0 ); - - RegVal = ((0x00000012U << LPD_XPPU_CFG_APERPERM_373_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_373_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_373_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_373_OFFSET ,0xF80FFFFFU ,0x08000012U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_374 @ 0XFF9815D8</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_374_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_374_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_374_PARITY 0x0 - - Entry 374 of the Aperture Permission List, for 32-byte IPI buffer 118 at BASE_32B + 0x00000EC0 - (OFFSET, MASK, VALUE) (0XFF9815D8, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_374_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_374_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_374_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_374_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_374_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_374_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_374_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_375 @ 0XFF9815DC</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_375_PERMISSION 0x2 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_375_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_375_PARITY 0x0 - - Entry 375 of the Aperture Permission List, for 32-byte IPI buffer 119 at BASE_32B + 0x00000EE0 - (OFFSET, MASK, VALUE) (0XFF9815DC, 0xF80FFFFFU ,0x08000002U) - RegMask = (LPD_XPPU_CFG_APERPERM_375_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_375_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_375_PARITY_MASK | 0 ); - - RegVal = ((0x00000002U << LPD_XPPU_CFG_APERPERM_375_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_375_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_375_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_375_OFFSET ,0xF80FFFFFU ,0x08000002U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_376 @ 0XFF9815E0</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_376_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_376_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_376_PARITY 0x0 - - Entry 376 of the Aperture Permission List, for 32-byte IPI buffer 120 at BASE_32B + 0x00000F00 - (OFFSET, MASK, VALUE) (0XFF9815E0, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_376_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_376_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_376_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_376_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_376_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_376_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_376_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_377 @ 0XFF9815E4</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_377_PERMISSION 0x2 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_377_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_377_PARITY 0x0 - - Entry 377 of the Aperture Permission List, for 32-byte IPI buffer 121 at BASE_32B + 0x00000F20 - (OFFSET, MASK, VALUE) (0XFF9815E4, 0xF80FFFFFU ,0x08000002U) - RegMask = (LPD_XPPU_CFG_APERPERM_377_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_377_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_377_PARITY_MASK | 0 ); - - RegVal = ((0x00000002U << LPD_XPPU_CFG_APERPERM_377_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_377_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_377_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_377_OFFSET ,0xF80FFFFFU ,0x08000002U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_378 @ 0XFF9815E8</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_378_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_378_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_378_PARITY 0x0 - - Entry 378 of the Aperture Permission List, for 32-byte IPI buffer 122 at BASE_32B + 0x00000F40 - (OFFSET, MASK, VALUE) (0XFF9815E8, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_378_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_378_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_378_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_378_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_378_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_378_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_378_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_379 @ 0XFF9815EC</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_379_PERMISSION 0x2 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_379_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_379_PARITY 0x0 - - Entry 379 of the Aperture Permission List, for 32-byte IPI buffer 123 at BASE_32B + 0x00000F60 - (OFFSET, MASK, VALUE) (0XFF9815EC, 0xF80FFFFFU ,0x08000002U) - RegMask = (LPD_XPPU_CFG_APERPERM_379_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_379_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_379_PARITY_MASK | 0 ); - - RegVal = ((0x00000002U << LPD_XPPU_CFG_APERPERM_379_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_379_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_379_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_379_OFFSET ,0xF80FFFFFU ,0x08000002U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_380 @ 0XFF9815F0</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_380_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_380_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_380_PARITY 0x0 - - Entry 380 of the Aperture Permission List, for 32-byte IPI buffer 124 at BASE_32B + 0x00000F80 - (OFFSET, MASK, VALUE) (0XFF9815F0, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_380_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_380_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_380_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_380_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_380_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_380_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_380_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_381 @ 0XFF9815F4</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_381_PERMISSION 0x2 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_381_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_381_PARITY 0x0 - - Entry 381 of the Aperture Permission List, for 32-byte IPI buffer 125 at BASE_32B + 0x00000FA0 - (OFFSET, MASK, VALUE) (0XFF9815F4, 0xF80FFFFFU ,0x08000002U) - RegMask = (LPD_XPPU_CFG_APERPERM_381_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_381_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_381_PARITY_MASK | 0 ); - - RegVal = ((0x00000002U << LPD_XPPU_CFG_APERPERM_381_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_381_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_381_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_381_OFFSET ,0xF80FFFFFU ,0x08000002U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_382 @ 0XFF9815F8</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_382_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_382_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_382_PARITY 0x0 - - Entry 382 of the Aperture Permission List, for 32-byte IPI buffer 126 at BASE_32B + 0x00000FC0 - (OFFSET, MASK, VALUE) (0XFF9815F8, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_382_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_382_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_382_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_382_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_382_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_382_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_382_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IPI_PMU, START ADDRESS: FF330000, END ADDRESS: FF33FFFF - /*Register : APERPERM_383 @ 0XFF9815FC</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_383_PERMISSION 0x20 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_383_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_383_PARITY 0x0 - - Entry 383 of the Aperture Permission List, for 32-byte IPI buffer 127 at BASE_32B + 0x00000FE0 - (OFFSET, MASK, VALUE) (0XFF9815FC, 0xF80FFFFFU ,0x08000020U) - RegMask = (LPD_XPPU_CFG_APERPERM_383_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_383_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_383_PARITY_MASK | 0 ); - - RegVal = ((0x00000020U << LPD_XPPU_CFG_APERPERM_383_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_383_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_383_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_383_OFFSET ,0xF80FFFFFU ,0x08000020U); - /*############################################################################################################################ */ - - // : APERTURE NAME: IOU_GPV, START ADDRESS: FE000000, END ADDRESS: FE0FFFFF - // : APERTURE NAME: LPD_GPV, START ADDRESS: FE100000, END ADDRESS: FE1FFFFF - // : APERTURE NAME: USB3_0_XHCI, START ADDRESS: FE200000, END ADDRESS: FE2FFFFF - // : APERTURE NAME: USB3_1_XHCI, START ADDRESS: FE300000, END ADDRESS: FE3FFFFF - // : APERTURE NAME: LPD_UNUSED_13, START ADDRESS: FE400000, END ADDRESS: FE7FFFFF - // : APERTURE NAME: LPD_UNUSED_13, START ADDRESS: FE400000, END ADDRESS: FE7FFFFF - // : APERTURE NAME: LPD_UNUSED_13, START ADDRESS: FE400000, END ADDRESS: FE7FFFFF - // : APERTURE NAME: LPD_UNUSED_13, START ADDRESS: FE400000, END ADDRESS: FE7FFFFF - // : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF - // : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF - // : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF - // : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF - // : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF - // : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF - // : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF - // : APERTURE NAME: CORESIGHT, START ADDRESS: FE800000, END ADDRESS: FEFFFFFF - // : APERTURE NAME: QSPI_LINEAR_ADDRESS, START ADDRESS: C0000000, END ADDRESS: DFFFFFFF - // : XPPU CONTROL - /*Register : err_ctrl @ 0XFF9CFFEC</p> - - Whether an APB access to the "hole" region and to an unimplemented register space causes PSLVERR - PSU_LPD_XPPU_SINK_ERR_CTRL_PSLVERR 1 - - Error control register - (OFFSET, MASK, VALUE) (0XFF9CFFEC, 0x00000001U ,0x00000001U) - RegMask = (LPD_XPPU_SINK_ERR_CTRL_PSLVERR_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_SINK_ERR_CTRL_PSLVERR_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_SINK_ERR_CTRL_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : CTRL @ 0XFF980000</p> - - 0=Bypass XPPU (transparent) 1=Enable XPPU permission checking - PSU_LPD_XPPU_CFG_CTRL_ENABLE 1 - - XPPU Control Register - (OFFSET, MASK, VALUE) (0XFF980000, 0x00000001U ,0x00000001U) - RegMask = (LPD_XPPU_CFG_CTRL_ENABLE_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_CTRL_ENABLE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_CTRL_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - // : XPPU INTERRUPT ENABLE - /*Register : IEN @ 0XFF980018</p> - - See Interuppt Status Register for details - PSU_LPD_XPPU_CFG_IEN_APER_PARITY 0X1 - - See Interuppt Status Register for details - PSU_LPD_XPPU_CFG_IEN_APER_TZ 0X1 - - See Interuppt Status Register for details - PSU_LPD_XPPU_CFG_IEN_APER_PERM 0X1 - - See Interuppt Status Register for details - PSU_LPD_XPPU_CFG_IEN_MID_PARITY 0X1 - - See Interuppt Status Register for details - PSU_LPD_XPPU_CFG_IEN_MID_RO 0X1 - - See Interuppt Status Register for details - PSU_LPD_XPPU_CFG_IEN_MID_MISS 0X1 - - See Interuppt Status Register for details - PSU_LPD_XPPU_CFG_IEN_INV_APB 0X1 - - Interrupt Enable Register - (OFFSET, MASK, VALUE) (0XFF980018, 0x000000EFU ,0x000000EFU) - RegMask = (LPD_XPPU_CFG_IEN_APER_PARITY_MASK | LPD_XPPU_CFG_IEN_APER_TZ_MASK | LPD_XPPU_CFG_IEN_APER_PERM_MASK | LPD_XPPU_CFG_IEN_MID_PARITY_MASK | LPD_XPPU_CFG_IEN_MID_RO_MASK | LPD_XPPU_CFG_IEN_MID_MISS_MASK | LPD_XPPU_CFG_IEN_INV_APB_MASK | 0 ); - - RegVal = ((0x00000001U << LPD_XPPU_CFG_IEN_APER_PARITY_SHIFT - | 0x00000001U << LPD_XPPU_CFG_IEN_APER_TZ_SHIFT - | 0x00000001U << LPD_XPPU_CFG_IEN_APER_PERM_SHIFT - | 0x00000001U << LPD_XPPU_CFG_IEN_MID_PARITY_SHIFT - | 0x00000001U << LPD_XPPU_CFG_IEN_MID_RO_SHIFT - | 0x00000001U << LPD_XPPU_CFG_IEN_MID_MISS_SHIFT - | 0x00000001U << LPD_XPPU_CFG_IEN_INV_APB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_IEN_OFFSET ,0x000000EFU ,0x000000EFU); - /*############################################################################################################################ */ - - - return 1; -} -unsigned long psu_ddr_xmpu0_data() { - // : DDR XMPU0 - - return 1; -} -unsigned long psu_ddr_xmpu1_data() { - // : DDR XMPU1 - - return 1; -} -unsigned long psu_ddr_xmpu2_data() { - // : DDR XMPU2 - - return 1; -} -unsigned long psu_ddr_xmpu3_data() { - // : DDR XMPU3 - - return 1; -} -unsigned long psu_ddr_xmpu4_data() { - // : DDR XMPU4 - - return 1; -} -unsigned long psu_ddr_xmpu5_data() { - // : DDR XMPU5 - - return 1; -} -unsigned long psu_ocm_xmpu_data() { - // : OCM XMPU - - return 1; -} -unsigned long psu_fpd_xmpu_data() { - // : FPD XMPU - - return 1; -} -unsigned long psu_protection_lock_data() { - // : LOCKING PROTECTION MODULE - // : XPPU LOCK - // : APERTURE NAME: LPD_XPPU, START ADDRESS: FF980000, END ADDRESS: FF99FFFF - /*Register : APERPERM_152 @ 0XFF981260</p> - - This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h. - PSU_LPD_XPPU_CFG_APERPERM_152_PERMISSION 0x0 - - 1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed - PSU_LPD_XPPU_CFG_APERPERM_152_TRUSTZONE 0x1 - - SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0 - PSU_LPD_XPPU_CFG_APERPERM_152_PARITY 0x0 - - Entry 152 of the Aperture Permission List, for the 64K-byte aperture at BASE_64KB + 0x00980000 - (OFFSET, MASK, VALUE) (0XFF981260, 0xF80FFFFFU ,0x08000000U) - RegMask = (LPD_XPPU_CFG_APERPERM_152_PERMISSION_MASK | LPD_XPPU_CFG_APERPERM_152_TRUSTZONE_MASK | LPD_XPPU_CFG_APERPERM_152_PARITY_MASK | 0 ); - - RegVal = ((0x00000000U << LPD_XPPU_CFG_APERPERM_152_PERMISSION_SHIFT - | 0x00000001U << LPD_XPPU_CFG_APERPERM_152_TRUSTZONE_SHIFT - | 0x00000000U << LPD_XPPU_CFG_APERPERM_152_PARITY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_XPPU_CFG_APERPERM_152_OFFSET ,0xF80FFFFFU ,0x08000000U); - /*############################################################################################################################ */ - - // : XMPU LOCK - - return 1; -} -unsigned long psu_apply_master_tz() { - // : RPU - // : DP TZ - // : SATA TZ - // : PCIE TZ - // : USB TZ - // : SD TZ - // : GEM TZ - // : QSPI TZ - // : NAND TZ - - return 1; -} -unsigned long psu_serdes_init_data() { - // : SERDES INITIALIZATION - // : GT REFERENCE CLOCK SOURCE SELECTION - /*Register : PLL_REF_SEL0 @ 0XFD410000</p> - - PLL0 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - - 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135 - Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved - PSU_SERDES_PLL_REF_SEL0_PLLREFSEL0 0x9 - - PLL0 Reference Selection Register - (OFFSET, MASK, VALUE) (0XFD410000, 0x0000001FU ,0x00000009U) - RegMask = (SERDES_PLL_REF_SEL0_PLLREFSEL0_MASK | 0 ); - - RegVal = ((0x00000009U << SERDES_PLL_REF_SEL0_PLLREFSEL0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_PLL_REF_SEL0_OFFSET ,0x0000001FU ,0x00000009U); - /*############################################################################################################################ */ - - /*Register : PLL_REF_SEL1 @ 0XFD410004</p> - - PLL1 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - - 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135 - Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved - PSU_SERDES_PLL_REF_SEL1_PLLREFSEL1 0x9 - - PLL1 Reference Selection Register - (OFFSET, MASK, VALUE) (0XFD410004, 0x0000001FU ,0x00000009U) - RegMask = (SERDES_PLL_REF_SEL1_PLLREFSEL1_MASK | 0 ); - - RegVal = ((0x00000009U << SERDES_PLL_REF_SEL1_PLLREFSEL1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_PLL_REF_SEL1_OFFSET ,0x0000001FU ,0x00000009U); - /*############################################################################################################################ */ - - /*Register : PLL_REF_SEL2 @ 0XFD410008</p> - - PLL2 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - - 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135 - Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved - PSU_SERDES_PLL_REF_SEL2_PLLREFSEL2 0x8 - - PLL2 Reference Selection Register - (OFFSET, MASK, VALUE) (0XFD410008, 0x0000001FU ,0x00000008U) - RegMask = (SERDES_PLL_REF_SEL2_PLLREFSEL2_MASK | 0 ); - - RegVal = ((0x00000008U << SERDES_PLL_REF_SEL2_PLLREFSEL2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_PLL_REF_SEL2_OFFSET ,0x0000001FU ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : PLL_REF_SEL3 @ 0XFD41000C</p> - - PLL3 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - - 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135 - Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved - PSU_SERDES_PLL_REF_SEL3_PLLREFSEL3 0xF - - PLL3 Reference Selection Register - (OFFSET, MASK, VALUE) (0XFD41000C, 0x0000001FU ,0x0000000FU) - RegMask = (SERDES_PLL_REF_SEL3_PLLREFSEL3_MASK | 0 ); - - RegVal = ((0x0000000FU << SERDES_PLL_REF_SEL3_PLLREFSEL3_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_PLL_REF_SEL3_OFFSET ,0x0000001FU ,0x0000000FU); - /*############################################################################################################################ */ - - // : GT REFERENCE CLOCK FREQUENCY SELECTION - /*Register : L0_L0_REF_CLK_SEL @ 0XFD402860</p> - - Sel of lane 0 ref clock local mux. Set to 1 to select lane 0 slicer output. Set to 0 to select lane0 ref clock mux output. - PSU_SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL 0x0 - - Bit 3 of lane 0 ref clock mux one hot sel. Set to 1 to select lane 3 slicer output from ref clock network - PSU_SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_SEL_3 0x1 - - Lane0 Ref Clock Selection Register - (OFFSET, MASK, VALUE) (0XFD402860, 0x00000088U ,0x00000008U) - RegMask = (SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL_MASK | SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_SEL_3_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL_SHIFT - | 0x00000001U << SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_SEL_3_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_L0_REF_CLK_SEL_OFFSET ,0x00000088U ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : L0_L1_REF_CLK_SEL @ 0XFD402864</p> - - Sel of lane 1 ref clock local mux. Set to 1 to select lane 1 slicer output. Set to 0 to select lane1 ref clock mux output. - PSU_SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL 0x0 - - Bit 3 of lane 1 ref clock mux one hot sel. Set to 1 to select lane 3 slicer output from ref clock network - PSU_SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3 0x1 - - Lane1 Ref Clock Selection Register - (OFFSET, MASK, VALUE) (0XFD402864, 0x00000088U ,0x00000008U) - RegMask = (SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL_MASK | SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL_SHIFT - | 0x00000001U << SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_L1_REF_CLK_SEL_OFFSET ,0x00000088U ,0x00000008U); - /*############################################################################################################################ */ - - /*Register : L0_L2_REF_CLK_SEL @ 0XFD402868</p> - - Sel of lane 2 ref clock local mux. Set to 1 to select lane 1 slicer output. Set to 0 to select lane2 ref clock mux output. - PSU_SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL 0x1 - - Lane2 Ref Clock Selection Register - (OFFSET, MASK, VALUE) (0XFD402868, 0x00000080U ,0x00000080U) - RegMask = (SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_L2_REF_CLK_SEL_OFFSET ,0x00000080U ,0x00000080U); - /*############################################################################################################################ */ - - /*Register : L0_L3_REF_CLK_SEL @ 0XFD40286C</p> - - Sel of lane 3 ref clock local mux. Set to 1 to select lane 3 slicer output. Set to 0 to select lane3 ref clock mux output. - PSU_SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL 0x0 - - Bit 1 of lane 3 ref clock mux one hot sel. Set to 1 to select lane 1 slicer output from ref clock network - PSU_SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1 0x1 - - Lane3 Ref Clock Selection Register - (OFFSET, MASK, VALUE) (0XFD40286C, 0x00000082U ,0x00000002U) - RegMask = (SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL_MASK | SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL_SHIFT - | 0x00000001U << SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_L3_REF_CLK_SEL_OFFSET ,0x00000082U ,0x00000002U); - /*############################################################################################################################ */ - - // : ENABLE SPREAD SPECTRUM - /*Register : L2_TM_PLL_DIG_37 @ 0XFD40A094</p> - - Enable/Disable coarse code satureation limiting logic - PSU_SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION 0x1 - - Test mode register 37 - (OFFSET, MASK, VALUE) (0XFD40A094, 0x00000010U ,0x00000010U) - RegMask = (SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_PLL_DIG_37_OFFSET ,0x00000010U ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : L2_PLL_SS_STEPS_0_LSB @ 0XFD40A368</p> - - Spread Spectrum No of Steps [7:0] - PSU_SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB 0x38 - - Spread Spectrum No of Steps bits 7:0 - (OFFSET, MASK, VALUE) (0XFD40A368, 0x000000FFU ,0x00000038U) - RegMask = (SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK | 0 ); - - RegVal = ((0x00000038U << SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_PLL_SS_STEPS_0_LSB_OFFSET ,0x000000FFU ,0x00000038U); - /*############################################################################################################################ */ - - /*Register : L2_PLL_SS_STEPS_1_MSB @ 0XFD40A36C</p> - - Spread Spectrum No of Steps [10:8] - PSU_SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB 0x03 - - Spread Spectrum No of Steps bits 10:8 - (OFFSET, MASK, VALUE) (0XFD40A36C, 0x00000007U ,0x00000003U) - RegMask = (SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK | 0 ); - - RegVal = ((0x00000003U << SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_PLL_SS_STEPS_1_MSB_OFFSET ,0x00000007U ,0x00000003U); - /*############################################################################################################################ */ - - /*Register : L3_PLL_SS_STEPS_0_LSB @ 0XFD40E368</p> - - Spread Spectrum No of Steps [7:0] - PSU_SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB 0xE0 - - Spread Spectrum No of Steps bits 7:0 - (OFFSET, MASK, VALUE) (0XFD40E368, 0x000000FFU ,0x000000E0U) - RegMask = (SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK | 0 ); - - RegVal = ((0x000000E0U << SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_PLL_SS_STEPS_0_LSB_OFFSET ,0x000000FFU ,0x000000E0U); - /*############################################################################################################################ */ - - /*Register : L3_PLL_SS_STEPS_1_MSB @ 0XFD40E36C</p> - - Spread Spectrum No of Steps [10:8] - PSU_SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB 0x3 - - Spread Spectrum No of Steps bits 10:8 - (OFFSET, MASK, VALUE) (0XFD40E36C, 0x00000007U ,0x00000003U) - RegMask = (SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK | 0 ); - - RegVal = ((0x00000003U << SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_PLL_SS_STEPS_1_MSB_OFFSET ,0x00000007U ,0x00000003U); - /*############################################################################################################################ */ - - /*Register : L0_PLL_SS_STEPS_0_LSB @ 0XFD402368</p> - - Spread Spectrum No of Steps [7:0] - PSU_SERDES_L0_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB 0x58 - - Spread Spectrum No of Steps bits 7:0 - (OFFSET, MASK, VALUE) (0XFD402368, 0x000000FFU ,0x00000058U) - RegMask = (SERDES_L0_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK | 0 ); - - RegVal = ((0x00000058U << SERDES_L0_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_PLL_SS_STEPS_0_LSB_OFFSET ,0x000000FFU ,0x00000058U); - /*############################################################################################################################ */ - - /*Register : L0_PLL_SS_STEPS_1_MSB @ 0XFD40236C</p> - - Spread Spectrum No of Steps [10:8] - PSU_SERDES_L0_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB 0x3 - - Spread Spectrum No of Steps bits 10:8 - (OFFSET, MASK, VALUE) (0XFD40236C, 0x00000007U ,0x00000003U) - RegMask = (SERDES_L0_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK | 0 ); - - RegVal = ((0x00000003U << SERDES_L0_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_PLL_SS_STEPS_1_MSB_OFFSET ,0x00000007U ,0x00000003U); - /*############################################################################################################################ */ - - /*Register : L1_PLL_SS_STEPS_0_LSB @ 0XFD406368</p> - - Spread Spectrum No of Steps [7:0] - PSU_SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB 0x58 - - Spread Spectrum No of Steps bits 7:0 - (OFFSET, MASK, VALUE) (0XFD406368, 0x000000FFU ,0x00000058U) - RegMask = (SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK | 0 ); - - RegVal = ((0x00000058U << SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_PLL_SS_STEPS_0_LSB_OFFSET ,0x000000FFU ,0x00000058U); - /*############################################################################################################################ */ - - /*Register : L1_PLL_SS_STEPS_1_MSB @ 0XFD40636C</p> - - Spread Spectrum No of Steps [10:8] - PSU_SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB 0x3 - - Spread Spectrum No of Steps bits 10:8 - (OFFSET, MASK, VALUE) (0XFD40636C, 0x00000007U ,0x00000003U) - RegMask = (SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK | 0 ); - - RegVal = ((0x00000003U << SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_PLL_SS_STEPS_1_MSB_OFFSET ,0x00000007U ,0x00000003U); - /*############################################################################################################################ */ - - /*Register : L0_PLL_SS_STEP_SIZE_0_LSB @ 0XFD402370</p> - - Step Size for Spread Spectrum [7:0] - PSU_SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB 0x7C - - Step Size for Spread Spectrum LSB - (OFFSET, MASK, VALUE) (0XFD402370, 0x000000FFU ,0x0000007CU) - RegMask = (SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK | 0 ); - - RegVal = ((0x0000007CU << SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_OFFSET ,0x000000FFU ,0x0000007CU); - /*############################################################################################################################ */ - - /*Register : L0_PLL_SS_STEP_SIZE_1 @ 0XFD402374</p> - - Step Size for Spread Spectrum [15:8] - PSU_SERDES_L0_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1 0x33 - - Step Size for Spread Spectrum 1 - (OFFSET, MASK, VALUE) (0XFD402374, 0x000000FFU ,0x00000033U) - RegMask = (SERDES_L0_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK | 0 ); - - RegVal = ((0x00000033U << SERDES_L0_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_PLL_SS_STEP_SIZE_1_OFFSET ,0x000000FFU ,0x00000033U); - /*############################################################################################################################ */ - - /*Register : L0_PLL_SS_STEP_SIZE_2 @ 0XFD402378</p> - - Step Size for Spread Spectrum [23:16] - PSU_SERDES_L0_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2 0x2 - - Step Size for Spread Spectrum 2 - (OFFSET, MASK, VALUE) (0XFD402378, 0x000000FFU ,0x00000002U) - RegMask = (SERDES_L0_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK | 0 ); - - RegVal = ((0x00000002U << SERDES_L0_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_PLL_SS_STEP_SIZE_2_OFFSET ,0x000000FFU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : L0_PLL_SS_STEP_SIZE_3_MSB @ 0XFD40237C</p> - - Step Size for Spread Spectrum [25:24] - PSU_SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB 0x0 - - Enable/Disable test mode force on SS step size - PSU_SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE 0x1 - - Enable/Disable test mode force on SS no of steps - PSU_SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS 0x1 - - Enable force on enable Spread Spectrum - (OFFSET, MASK, VALUE) (0XFD40237C, 0x00000033U ,0x00000030U) - RegMask = (SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK | SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK | SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT - | 0x00000001U << SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT - | 0x00000001U << SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_OFFSET ,0x00000033U ,0x00000030U); - /*############################################################################################################################ */ - - /*Register : L1_PLL_SS_STEP_SIZE_0_LSB @ 0XFD406370</p> - - Step Size for Spread Spectrum [7:0] - PSU_SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB 0x7C - - Step Size for Spread Spectrum LSB - (OFFSET, MASK, VALUE) (0XFD406370, 0x000000FFU ,0x0000007CU) - RegMask = (SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK | 0 ); - - RegVal = ((0x0000007CU << SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_OFFSET ,0x000000FFU ,0x0000007CU); - /*############################################################################################################################ */ - - /*Register : L1_PLL_SS_STEP_SIZE_1 @ 0XFD406374</p> - - Step Size for Spread Spectrum [15:8] - PSU_SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1 0x33 - - Step Size for Spread Spectrum 1 - (OFFSET, MASK, VALUE) (0XFD406374, 0x000000FFU ,0x00000033U) - RegMask = (SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK | 0 ); - - RegVal = ((0x00000033U << SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_PLL_SS_STEP_SIZE_1_OFFSET ,0x000000FFU ,0x00000033U); - /*############################################################################################################################ */ - - /*Register : L1_PLL_SS_STEP_SIZE_2 @ 0XFD406378</p> - - Step Size for Spread Spectrum [23:16] - PSU_SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2 0x2 - - Step Size for Spread Spectrum 2 - (OFFSET, MASK, VALUE) (0XFD406378, 0x000000FFU ,0x00000002U) - RegMask = (SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK | 0 ); - - RegVal = ((0x00000002U << SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_PLL_SS_STEP_SIZE_2_OFFSET ,0x000000FFU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : L1_PLL_SS_STEP_SIZE_3_MSB @ 0XFD40637C</p> - - Step Size for Spread Spectrum [25:24] - PSU_SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB 0x0 - - Enable/Disable test mode force on SS step size - PSU_SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE 0x1 - - Enable/Disable test mode force on SS no of steps - PSU_SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS 0x1 - - Enable force on enable Spread Spectrum - (OFFSET, MASK, VALUE) (0XFD40637C, 0x00000033U ,0x00000030U) - RegMask = (SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK | SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK | SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT - | 0x00000001U << SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT - | 0x00000001U << SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_OFFSET ,0x00000033U ,0x00000030U); - /*############################################################################################################################ */ - - /*Register : L2_PLL_SS_STEP_SIZE_0_LSB @ 0XFD40A370</p> - - Step Size for Spread Spectrum [7:0] - PSU_SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB 0xF4 - - Step Size for Spread Spectrum LSB - (OFFSET, MASK, VALUE) (0XFD40A370, 0x000000FFU ,0x000000F4U) - RegMask = (SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK | 0 ); - - RegVal = ((0x000000F4U << SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_OFFSET ,0x000000FFU ,0x000000F4U); - /*############################################################################################################################ */ - - /*Register : L2_PLL_SS_STEP_SIZE_1 @ 0XFD40A374</p> - - Step Size for Spread Spectrum [15:8] - PSU_SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1 0x31 - - Step Size for Spread Spectrum 1 - (OFFSET, MASK, VALUE) (0XFD40A374, 0x000000FFU ,0x00000031U) - RegMask = (SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK | 0 ); - - RegVal = ((0x00000031U << SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_PLL_SS_STEP_SIZE_1_OFFSET ,0x000000FFU ,0x00000031U); - /*############################################################################################################################ */ - - /*Register : L2_PLL_SS_STEP_SIZE_2 @ 0XFD40A378</p> - - Step Size for Spread Spectrum [23:16] - PSU_SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2 0x2 - - Step Size for Spread Spectrum 2 - (OFFSET, MASK, VALUE) (0XFD40A378, 0x000000FFU ,0x00000002U) - RegMask = (SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK | 0 ); - - RegVal = ((0x00000002U << SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_PLL_SS_STEP_SIZE_2_OFFSET ,0x000000FFU ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : L2_PLL_SS_STEP_SIZE_3_MSB @ 0XFD40A37C</p> - - Step Size for Spread Spectrum [25:24] - PSU_SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB 0x0 - - Enable/Disable test mode force on SS step size - PSU_SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE 0x1 - - Enable/Disable test mode force on SS no of steps - PSU_SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS 0x1 - - Enable force on enable Spread Spectrum - (OFFSET, MASK, VALUE) (0XFD40A37C, 0x00000033U ,0x00000030U) - RegMask = (SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK | SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK | SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT - | 0x00000001U << SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT - | 0x00000001U << SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_OFFSET ,0x00000033U ,0x00000030U); - /*############################################################################################################################ */ - - /*Register : L3_PLL_SS_STEP_SIZE_0_LSB @ 0XFD40E370</p> - - Step Size for Spread Spectrum [7:0] - PSU_SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB 0xC9 - - Step Size for Spread Spectrum LSB - (OFFSET, MASK, VALUE) (0XFD40E370, 0x000000FFU ,0x000000C9U) - RegMask = (SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK | 0 ); - - RegVal = ((0x000000C9U << SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_OFFSET ,0x000000FFU ,0x000000C9U); - /*############################################################################################################################ */ - - /*Register : L3_PLL_SS_STEP_SIZE_1 @ 0XFD40E374</p> - - Step Size for Spread Spectrum [15:8] - PSU_SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1 0xD2 - - Step Size for Spread Spectrum 1 - (OFFSET, MASK, VALUE) (0XFD40E374, 0x000000FFU ,0x000000D2U) - RegMask = (SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK | 0 ); - - RegVal = ((0x000000D2U << SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_PLL_SS_STEP_SIZE_1_OFFSET ,0x000000FFU ,0x000000D2U); - /*############################################################################################################################ */ - - /*Register : L3_PLL_SS_STEP_SIZE_2 @ 0XFD40E378</p> - - Step Size for Spread Spectrum [23:16] - PSU_SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2 0x1 - - Step Size for Spread Spectrum 2 - (OFFSET, MASK, VALUE) (0XFD40E378, 0x000000FFU ,0x00000001U) - RegMask = (SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_PLL_SS_STEP_SIZE_2_OFFSET ,0x000000FFU ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : L3_PLL_SS_STEP_SIZE_3_MSB @ 0XFD40E37C</p> - - Step Size for Spread Spectrum [25:24] - PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB 0x0 - - Enable/Disable test mode force on SS step size - PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE 0x1 - - Enable/Disable test mode force on SS no of steps - PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS 0x1 - - Enable test mode forcing on enable Spread Spectrum - PSU_SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS 0x1 - - Enable force on enable Spread Spectrum - (OFFSET, MASK, VALUE) (0XFD40E37C, 0x000000B3U ,0x000000B0U) - RegMask = (SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK | SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK | SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK | SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT - | 0x00000001U << SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT - | 0x00000001U << SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT - | 0x00000001U << SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_OFFSET ,0x000000B3U ,0x000000B0U); - /*############################################################################################################################ */ - - /*Register : L2_TM_DIG_6 @ 0XFD40906C</p> - - Bypass Descrambler - PSU_SERDES_L2_TM_DIG_6_BYPASS_DESCRAM 0x1 - - Enable Bypass for <1> TM_DIG_CTRL_6 - PSU_SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM 0x1 - - Data path test modes in decoder and descram - (OFFSET, MASK, VALUE) (0XFD40906C, 0x00000003U ,0x00000003U) - RegMask = (SERDES_L2_TM_DIG_6_BYPASS_DESCRAM_MASK | SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L2_TM_DIG_6_BYPASS_DESCRAM_SHIFT - | 0x00000001U << SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_DIG_6_OFFSET ,0x00000003U ,0x00000003U); - /*############################################################################################################################ */ - - /*Register : L2_TX_DIG_TM_61 @ 0XFD4080F4</p> - - Bypass scrambler signal - PSU_SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM 0x1 - - Enable/disable scrambler bypass signal - PSU_SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM 0x1 - - MPHY PLL Gear and bypass scrambler - (OFFSET, MASK, VALUE) (0XFD4080F4, 0x00000003U ,0x00000003U) - RegMask = (SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM_MASK | SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM_SHIFT - | 0x00000001U << SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TX_DIG_TM_61_OFFSET ,0x00000003U ,0x00000003U); - /*############################################################################################################################ */ - - /*Register : L3_PLL_FBDIV_FRAC_3_MSB @ 0XFD40E360</p> - - Enable test mode force on fractional mode enable - PSU_SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC 0x1 - - Fractional feedback division control and fractional value for feedback division bits 26:24 - (OFFSET, MASK, VALUE) (0XFD40E360, 0x00000040U ,0x00000040U) - RegMask = (SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_PLL_FBDIV_FRAC_3_MSB_OFFSET ,0x00000040U ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : L3_TM_DIG_6 @ 0XFD40D06C</p> - - Bypass 8b10b decoder - PSU_SERDES_L3_TM_DIG_6_BYPASS_DECODER 0x1 - - Enable Bypass for <3> TM_DIG_CTRL_6 - PSU_SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC 0x1 - - Bypass Descrambler - PSU_SERDES_L3_TM_DIG_6_BYPASS_DESCRAM 0x1 - - Enable Bypass for <1> TM_DIG_CTRL_6 - PSU_SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM 0x1 - - Data path test modes in decoder and descram - (OFFSET, MASK, VALUE) (0XFD40D06C, 0x0000000FU ,0x0000000FU) - RegMask = (SERDES_L3_TM_DIG_6_BYPASS_DECODER_MASK | SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC_MASK | SERDES_L3_TM_DIG_6_BYPASS_DESCRAM_MASK | SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TM_DIG_6_BYPASS_DECODER_SHIFT - | 0x00000001U << SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC_SHIFT - | 0x00000001U << SERDES_L3_TM_DIG_6_BYPASS_DESCRAM_SHIFT - | 0x00000001U << SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_DIG_6_OFFSET ,0x0000000FU ,0x0000000FU); - /*############################################################################################################################ */ - - /*Register : L3_TX_DIG_TM_61 @ 0XFD40C0F4</p> - - Enable/disable encoder bypass signal - PSU_SERDES_L3_TX_DIG_TM_61_BYPASS_ENC 0x1 - - Bypass scrambler signal - PSU_SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM 0x1 - - Enable/disable scrambler bypass signal - PSU_SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM 0x1 - - MPHY PLL Gear and bypass scrambler - (OFFSET, MASK, VALUE) (0XFD40C0F4, 0x0000000BU ,0x0000000BU) - RegMask = (SERDES_L3_TX_DIG_TM_61_BYPASS_ENC_MASK | SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM_MASK | SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TX_DIG_TM_61_BYPASS_ENC_SHIFT - | 0x00000001U << SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM_SHIFT - | 0x00000001U << SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TX_DIG_TM_61_OFFSET ,0x0000000BU ,0x0000000BU); - /*############################################################################################################################ */ - - /*Register : L3_TXPMA_ST_0 @ 0XFD40CB00</p> - - PHY Mode: 4'b000 - PCIe, 4'b001 - USB3, 4'b0010 - SATA, 4'b0100 - SGMII, 4'b0101 - DP, 4'b1000 - MPHY - PSU_SERDES_L3_TXPMA_ST_0_TX_PHY_MODE 0x21 - - Opmode Info - (OFFSET, MASK, VALUE) (0XFD40CB00, 0x000000F0U ,0x000000F0U) - RegMask = (SERDES_L3_TXPMA_ST_0_TX_PHY_MODE_MASK | 0 ); - - RegVal = ((0x00000021U << SERDES_L3_TXPMA_ST_0_TX_PHY_MODE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TXPMA_ST_0_OFFSET ,0x000000F0U ,0x000000F0U); - /*############################################################################################################################ */ - - // : ENABLE CHICKEN BIT FOR PCIE AND USB - /*Register : L2_TM_AUX_0 @ 0XFD4090CC</p> - - Spare- not used - PSU_SERDES_L2_TM_AUX_0_BIT_2 1 - - Spare registers - (OFFSET, MASK, VALUE) (0XFD4090CC, 0x00000020U ,0x00000020U) - RegMask = (SERDES_L2_TM_AUX_0_BIT_2_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L2_TM_AUX_0_BIT_2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_AUX_0_OFFSET ,0x00000020U ,0x00000020U); - /*############################################################################################################################ */ - - // : ENABLING EYE SURF - /*Register : L0_TM_DIG_8 @ 0XFD401074</p> - - Enable Eye Surf - PSU_SERDES_L0_TM_DIG_8_EYESURF_ENABLE 0x1 - - Test modes for Elastic buffer and enabling Eye Surf - (OFFSET, MASK, VALUE) (0XFD401074, 0x00000010U ,0x00000010U) - RegMask = (SERDES_L0_TM_DIG_8_EYESURF_ENABLE_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L0_TM_DIG_8_EYESURF_ENABLE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_TM_DIG_8_OFFSET ,0x00000010U ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : L1_TM_DIG_8 @ 0XFD405074</p> - - Enable Eye Surf - PSU_SERDES_L1_TM_DIG_8_EYESURF_ENABLE 0x1 - - Test modes for Elastic buffer and enabling Eye Surf - (OFFSET, MASK, VALUE) (0XFD405074, 0x00000010U ,0x00000010U) - RegMask = (SERDES_L1_TM_DIG_8_EYESURF_ENABLE_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L1_TM_DIG_8_EYESURF_ENABLE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_TM_DIG_8_OFFSET ,0x00000010U ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : L2_TM_DIG_8 @ 0XFD409074</p> - - Enable Eye Surf - PSU_SERDES_L2_TM_DIG_8_EYESURF_ENABLE 0x1 - - Test modes for Elastic buffer and enabling Eye Surf - (OFFSET, MASK, VALUE) (0XFD409074, 0x00000010U ,0x00000010U) - RegMask = (SERDES_L2_TM_DIG_8_EYESURF_ENABLE_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L2_TM_DIG_8_EYESURF_ENABLE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_DIG_8_OFFSET ,0x00000010U ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : L3_TM_DIG_8 @ 0XFD40D074</p> - - Enable Eye Surf - PSU_SERDES_L3_TM_DIG_8_EYESURF_ENABLE 0x1 - - Test modes for Elastic buffer and enabling Eye Surf - (OFFSET, MASK, VALUE) (0XFD40D074, 0x00000010U ,0x00000010U) - RegMask = (SERDES_L3_TM_DIG_8_EYESURF_ENABLE_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TM_DIG_8_EYESURF_ENABLE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_DIG_8_OFFSET ,0x00000010U ,0x00000010U); - /*############################################################################################################################ */ - - // : ILL SETTINGS FOR GAIN AND LOCK SETTINGS - /*Register : L2_TM_MISC2 @ 0XFD40989C</p> - - ILL calib counts BYPASSED with calcode bits - PSU_SERDES_L2_TM_MISC2_ILL_CAL_BYPASS_COUNTS 0x1 - - sampler cal - (OFFSET, MASK, VALUE) (0XFD40989C, 0x00000080U ,0x00000080U) - RegMask = (SERDES_L2_TM_MISC2_ILL_CAL_BYPASS_COUNTS_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L2_TM_MISC2_ILL_CAL_BYPASS_COUNTS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_MISC2_OFFSET ,0x00000080U ,0x00000080U); - /*############################################################################################################################ */ - - /*Register : L2_TM_IQ_ILL1 @ 0XFD4098F8</p> - - IQ ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , USB3 : SS - PSU_SERDES_L2_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0 0x1A - - iqpi cal code - (OFFSET, MASK, VALUE) (0XFD4098F8, 0x000000FFU ,0x0000001AU) - RegMask = (SERDES_L2_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_MASK | 0 ); - - RegVal = ((0x0000001AU << SERDES_L2_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_IQ_ILL1_OFFSET ,0x000000FFU ,0x0000001AU); - /*############################################################################################################################ */ - - /*Register : L2_TM_IQ_ILL2 @ 0XFD4098FC</p> - - IQ ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2 - PSU_SERDES_L2_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1 0x1A - - iqpi cal code - (OFFSET, MASK, VALUE) (0XFD4098FC, 0x000000FFU ,0x0000001AU) - RegMask = (SERDES_L2_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_MASK | 0 ); - - RegVal = ((0x0000001AU << SERDES_L2_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_IQ_ILL2_OFFSET ,0x000000FFU ,0x0000001AU); - /*############################################################################################################################ */ - - /*Register : L2_TM_ILL12 @ 0XFD409990</p> - - G1A pll ctr bypass value - PSU_SERDES_L2_TM_ILL12_G1A_PLL_CTR_BYP_VAL 0x10 - - ill pll counter values - (OFFSET, MASK, VALUE) (0XFD409990, 0x000000FFU ,0x00000010U) - RegMask = (SERDES_L2_TM_ILL12_G1A_PLL_CTR_BYP_VAL_MASK | 0 ); - - RegVal = ((0x00000010U << SERDES_L2_TM_ILL12_G1A_PLL_CTR_BYP_VAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_ILL12_OFFSET ,0x000000FFU ,0x00000010U); - /*############################################################################################################################ */ - - /*Register : L2_TM_E_ILL1 @ 0XFD409924</p> - - E ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , USB3 : SS - PSU_SERDES_L2_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0 0xFE - - epi cal code - (OFFSET, MASK, VALUE) (0XFD409924, 0x000000FFU ,0x000000FEU) - RegMask = (SERDES_L2_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_MASK | 0 ); - - RegVal = ((0x000000FEU << SERDES_L2_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_E_ILL1_OFFSET ,0x000000FFU ,0x000000FEU); - /*############################################################################################################################ */ - - /*Register : L2_TM_E_ILL2 @ 0XFD409928</p> - - E ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2 - PSU_SERDES_L2_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1 0x0 - - epi cal code - (OFFSET, MASK, VALUE) (0XFD409928, 0x000000FFU ,0x00000000U) - RegMask = (SERDES_L2_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L2_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_E_ILL2_OFFSET ,0x000000FFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : L2_TM_IQ_ILL3 @ 0XFD409900</p> - - IQ ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3 - PSU_SERDES_L2_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2 0x1A - - iqpi cal code - (OFFSET, MASK, VALUE) (0XFD409900, 0x000000FFU ,0x0000001AU) - RegMask = (SERDES_L2_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_MASK | 0 ); - - RegVal = ((0x0000001AU << SERDES_L2_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_IQ_ILL3_OFFSET ,0x000000FFU ,0x0000001AU); - /*############################################################################################################################ */ - - /*Register : L2_TM_E_ILL3 @ 0XFD40992C</p> - - E ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3 - PSU_SERDES_L2_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2 0x0 - - epi cal code - (OFFSET, MASK, VALUE) (0XFD40992C, 0x000000FFU ,0x00000000U) - RegMask = (SERDES_L2_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L2_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_E_ILL3_OFFSET ,0x000000FFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : L2_TM_ILL8 @ 0XFD409980</p> - - ILL calibration code change wait time - PSU_SERDES_L2_TM_ILL8_ILL_CAL_ITER_WAIT 0xFF - - ILL cal routine control - (OFFSET, MASK, VALUE) (0XFD409980, 0x000000FFU ,0x000000FFU) - RegMask = (SERDES_L2_TM_ILL8_ILL_CAL_ITER_WAIT_MASK | 0 ); - - RegVal = ((0x000000FFU << SERDES_L2_TM_ILL8_ILL_CAL_ITER_WAIT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_ILL8_OFFSET ,0x000000FFU ,0x000000FFU); - /*############################################################################################################################ */ - - /*Register : L2_TM_IQ_ILL8 @ 0XFD409914</p> - - IQ ILL polytrim bypass value - PSU_SERDES_L2_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL 0xF7 - - iqpi polytrim - (OFFSET, MASK, VALUE) (0XFD409914, 0x000000FFU ,0x000000F7U) - RegMask = (SERDES_L2_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_MASK | 0 ); - - RegVal = ((0x000000F7U << SERDES_L2_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_IQ_ILL8_OFFSET ,0x000000FFU ,0x000000F7U); - /*############################################################################################################################ */ - - /*Register : L2_TM_IQ_ILL9 @ 0XFD409918</p> - - bypass IQ polytrim - PSU_SERDES_L2_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM 0x1 - - enables for lf,constant gm trim and polytirm - (OFFSET, MASK, VALUE) (0XFD409918, 0x00000001U ,0x00000001U) - RegMask = (SERDES_L2_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L2_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_IQ_ILL9_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : L2_TM_E_ILL8 @ 0XFD409940</p> - - E ILL polytrim bypass value - PSU_SERDES_L2_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL 0xF7 - - epi polytrim - (OFFSET, MASK, VALUE) (0XFD409940, 0x000000FFU ,0x000000F7U) - RegMask = (SERDES_L2_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_MASK | 0 ); - - RegVal = ((0x000000F7U << SERDES_L2_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_E_ILL8_OFFSET ,0x000000FFU ,0x000000F7U); - /*############################################################################################################################ */ - - /*Register : L2_TM_E_ILL9 @ 0XFD409944</p> - - bypass E polytrim - PSU_SERDES_L2_TM_E_ILL9_ILL_BYPASS_E_POLYTIM 0x1 - - enables for lf,constant gm trim and polytirm - (OFFSET, MASK, VALUE) (0XFD409944, 0x00000001U ,0x00000001U) - RegMask = (SERDES_L2_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L2_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_E_ILL9_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : L3_TM_MISC2 @ 0XFD40D89C</p> - - ILL calib counts BYPASSED with calcode bits - PSU_SERDES_L3_TM_MISC2_ILL_CAL_BYPASS_COUNTS 0x1 - - sampler cal - (OFFSET, MASK, VALUE) (0XFD40D89C, 0x00000080U ,0x00000080U) - RegMask = (SERDES_L3_TM_MISC2_ILL_CAL_BYPASS_COUNTS_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TM_MISC2_ILL_CAL_BYPASS_COUNTS_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_MISC2_OFFSET ,0x00000080U ,0x00000080U); - /*############################################################################################################################ */ - - /*Register : L3_TM_IQ_ILL1 @ 0XFD40D8F8</p> - - IQ ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , USB3 : SS - PSU_SERDES_L3_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0 0x7D - - iqpi cal code - (OFFSET, MASK, VALUE) (0XFD40D8F8, 0x000000FFU ,0x0000007DU) - RegMask = (SERDES_L3_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_MASK | 0 ); - - RegVal = ((0x0000007DU << SERDES_L3_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_IQ_ILL1_OFFSET ,0x000000FFU ,0x0000007DU); - /*############################################################################################################################ */ - - /*Register : L3_TM_IQ_ILL2 @ 0XFD40D8FC</p> - - IQ ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2 - PSU_SERDES_L3_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1 0x7D - - iqpi cal code - (OFFSET, MASK, VALUE) (0XFD40D8FC, 0x000000FFU ,0x0000007DU) - RegMask = (SERDES_L3_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_MASK | 0 ); - - RegVal = ((0x0000007DU << SERDES_L3_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_IQ_ILL2_OFFSET ,0x000000FFU ,0x0000007DU); - /*############################################################################################################################ */ - - /*Register : L3_TM_ILL12 @ 0XFD40D990</p> - - G1A pll ctr bypass value - PSU_SERDES_L3_TM_ILL12_G1A_PLL_CTR_BYP_VAL 0x1 - - ill pll counter values - (OFFSET, MASK, VALUE) (0XFD40D990, 0x000000FFU ,0x00000001U) - RegMask = (SERDES_L3_TM_ILL12_G1A_PLL_CTR_BYP_VAL_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TM_ILL12_G1A_PLL_CTR_BYP_VAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_ILL12_OFFSET ,0x000000FFU ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : L3_TM_E_ILL1 @ 0XFD40D924</p> - - E ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , USB3 : SS - PSU_SERDES_L3_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0 0x9C - - epi cal code - (OFFSET, MASK, VALUE) (0XFD40D924, 0x000000FFU ,0x0000009CU) - RegMask = (SERDES_L3_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_MASK | 0 ); - - RegVal = ((0x0000009CU << SERDES_L3_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_E_ILL1_OFFSET ,0x000000FFU ,0x0000009CU); - /*############################################################################################################################ */ - - /*Register : L3_TM_E_ILL2 @ 0XFD40D928</p> - - E ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2 - PSU_SERDES_L3_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1 0x39 - - epi cal code - (OFFSET, MASK, VALUE) (0XFD40D928, 0x000000FFU ,0x00000039U) - RegMask = (SERDES_L3_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_MASK | 0 ); - - RegVal = ((0x00000039U << SERDES_L3_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_E_ILL2_OFFSET ,0x000000FFU ,0x00000039U); - /*############################################################################################################################ */ - - /*Register : L3_TM_ILL11 @ 0XFD40D98C</p> - - G2A_PCIe1 PLL ctr bypass value - PSU_SERDES_L3_TM_ILL11_G2A_PCIEG1_PLL_CTR_11_8_BYP_VAL 0x2 - - ill pll counter values - (OFFSET, MASK, VALUE) (0XFD40D98C, 0x000000F0U ,0x00000020U) - RegMask = (SERDES_L3_TM_ILL11_G2A_PCIEG1_PLL_CTR_11_8_BYP_VAL_MASK | 0 ); - - RegVal = ((0x00000002U << SERDES_L3_TM_ILL11_G2A_PCIEG1_PLL_CTR_11_8_BYP_VAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_ILL11_OFFSET ,0x000000F0U ,0x00000020U); - /*############################################################################################################################ */ - - /*Register : L3_TM_IQ_ILL3 @ 0XFD40D900</p> - - IQ ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3 - PSU_SERDES_L3_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2 0x7D - - iqpi cal code - (OFFSET, MASK, VALUE) (0XFD40D900, 0x000000FFU ,0x0000007DU) - RegMask = (SERDES_L3_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_MASK | 0 ); - - RegVal = ((0x0000007DU << SERDES_L3_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_IQ_ILL3_OFFSET ,0x000000FFU ,0x0000007DU); - /*############################################################################################################################ */ - - /*Register : L3_TM_E_ILL3 @ 0XFD40D92C</p> - - E ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3 - PSU_SERDES_L3_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2 0x64 - - epi cal code - (OFFSET, MASK, VALUE) (0XFD40D92C, 0x000000FFU ,0x00000064U) - RegMask = (SERDES_L3_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_MASK | 0 ); - - RegVal = ((0x00000064U << SERDES_L3_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_E_ILL3_OFFSET ,0x000000FFU ,0x00000064U); - /*############################################################################################################################ */ - - /*Register : L3_TM_ILL8 @ 0XFD40D980</p> - - ILL calibration code change wait time - PSU_SERDES_L3_TM_ILL8_ILL_CAL_ITER_WAIT 0xFF - - ILL cal routine control - (OFFSET, MASK, VALUE) (0XFD40D980, 0x000000FFU ,0x000000FFU) - RegMask = (SERDES_L3_TM_ILL8_ILL_CAL_ITER_WAIT_MASK | 0 ); - - RegVal = ((0x000000FFU << SERDES_L3_TM_ILL8_ILL_CAL_ITER_WAIT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_ILL8_OFFSET ,0x000000FFU ,0x000000FFU); - /*############################################################################################################################ */ - - /*Register : L3_TM_IQ_ILL8 @ 0XFD40D914</p> - - IQ ILL polytrim bypass value - PSU_SERDES_L3_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL 0xF7 - - iqpi polytrim - (OFFSET, MASK, VALUE) (0XFD40D914, 0x000000FFU ,0x000000F7U) - RegMask = (SERDES_L3_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_MASK | 0 ); - - RegVal = ((0x000000F7U << SERDES_L3_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_IQ_ILL8_OFFSET ,0x000000FFU ,0x000000F7U); - /*############################################################################################################################ */ - - /*Register : L3_TM_IQ_ILL9 @ 0XFD40D918</p> - - bypass IQ polytrim - PSU_SERDES_L3_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM 0x1 - - enables for lf,constant gm trim and polytirm - (OFFSET, MASK, VALUE) (0XFD40D918, 0x00000001U ,0x00000001U) - RegMask = (SERDES_L3_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_IQ_ILL9_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : L3_TM_E_ILL8 @ 0XFD40D940</p> - - E ILL polytrim bypass value - PSU_SERDES_L3_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL 0xF7 - - epi polytrim - (OFFSET, MASK, VALUE) (0XFD40D940, 0x000000FFU ,0x000000F7U) - RegMask = (SERDES_L3_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_MASK | 0 ); - - RegVal = ((0x000000F7U << SERDES_L3_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_E_ILL8_OFFSET ,0x000000FFU ,0x000000F7U); - /*############################################################################################################################ */ - - /*Register : L3_TM_E_ILL9 @ 0XFD40D944</p> - - bypass E polytrim - PSU_SERDES_L3_TM_E_ILL9_ILL_BYPASS_E_POLYTIM 0x1 - - enables for lf,constant gm trim and polytirm - (OFFSET, MASK, VALUE) (0XFD40D944, 0x00000001U ,0x00000001U) - RegMask = (SERDES_L3_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_E_ILL9_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - // : SYMBOL LOCK AND WAIT - // : SIOU SETTINGS FOR BYPASS CONTROL,HSRX-DIG - /*Register : L0_TM_RST_DLY @ 0XFD4019A4</p> - - Delay apb reset by specified amount - PSU_SERDES_L0_TM_RST_DLY_APB_RST_DLY 0xFF - - reset delay for apb reset w.r.t pso of hsrx - (OFFSET, MASK, VALUE) (0XFD4019A4, 0x000000FFU ,0x000000FFU) - RegMask = (SERDES_L0_TM_RST_DLY_APB_RST_DLY_MASK | 0 ); - - RegVal = ((0x000000FFU << SERDES_L0_TM_RST_DLY_APB_RST_DLY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_TM_RST_DLY_OFFSET ,0x000000FFU ,0x000000FFU); - /*############################################################################################################################ */ - - /*Register : L0_TM_ANA_BYP_15 @ 0XFD401038</p> - - Enable Bypass for <7> of TM_ANA_BYPS_15 - PSU_SERDES_L0_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE 0x1 - - Bypass control for pcs-pma interface. EQ supplies, main master supply and ps for samp c2c - (OFFSET, MASK, VALUE) (0XFD401038, 0x00000040U ,0x00000040U) - RegMask = (SERDES_L0_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L0_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_TM_ANA_BYP_15_OFFSET ,0x00000040U ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : L0_TM_ANA_BYP_12 @ 0XFD40102C</p> - - Enable Bypass for <7> of TM_ANA_BYPS_12 - PSU_SERDES_L0_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG 0x1 - - Bypass control for pcs-pma interface. Hsrx supply, hsrx des, and cdr enable controls - (OFFSET, MASK, VALUE) (0XFD40102C, 0x00000040U ,0x00000040U) - RegMask = (SERDES_L0_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L0_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_TM_ANA_BYP_12_OFFSET ,0x00000040U ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : L1_TM_RST_DLY @ 0XFD4059A4</p> - - Delay apb reset by specified amount - PSU_SERDES_L1_TM_RST_DLY_APB_RST_DLY 0xFF - - reset delay for apb reset w.r.t pso of hsrx - (OFFSET, MASK, VALUE) (0XFD4059A4, 0x000000FFU ,0x000000FFU) - RegMask = (SERDES_L1_TM_RST_DLY_APB_RST_DLY_MASK | 0 ); - - RegVal = ((0x000000FFU << SERDES_L1_TM_RST_DLY_APB_RST_DLY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_TM_RST_DLY_OFFSET ,0x000000FFU ,0x000000FFU); - /*############################################################################################################################ */ - - /*Register : L1_TM_ANA_BYP_15 @ 0XFD405038</p> - - Enable Bypass for <7> of TM_ANA_BYPS_15 - PSU_SERDES_L1_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE 0x1 - - Bypass control for pcs-pma interface. EQ supplies, main master supply and ps for samp c2c - (OFFSET, MASK, VALUE) (0XFD405038, 0x00000040U ,0x00000040U) - RegMask = (SERDES_L1_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L1_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_TM_ANA_BYP_15_OFFSET ,0x00000040U ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : L1_TM_ANA_BYP_12 @ 0XFD40502C</p> - - Enable Bypass for <7> of TM_ANA_BYPS_12 - PSU_SERDES_L1_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG 0x1 - - Bypass control for pcs-pma interface. Hsrx supply, hsrx des, and cdr enable controls - (OFFSET, MASK, VALUE) (0XFD40502C, 0x00000040U ,0x00000040U) - RegMask = (SERDES_L1_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L1_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_TM_ANA_BYP_12_OFFSET ,0x00000040U ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : L2_TM_RST_DLY @ 0XFD4099A4</p> - - Delay apb reset by specified amount - PSU_SERDES_L2_TM_RST_DLY_APB_RST_DLY 0xFF - - reset delay for apb reset w.r.t pso of hsrx - (OFFSET, MASK, VALUE) (0XFD4099A4, 0x000000FFU ,0x000000FFU) - RegMask = (SERDES_L2_TM_RST_DLY_APB_RST_DLY_MASK | 0 ); - - RegVal = ((0x000000FFU << SERDES_L2_TM_RST_DLY_APB_RST_DLY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_RST_DLY_OFFSET ,0x000000FFU ,0x000000FFU); - /*############################################################################################################################ */ - - /*Register : L2_TM_ANA_BYP_15 @ 0XFD409038</p> - - Enable Bypass for <7> of TM_ANA_BYPS_15 - PSU_SERDES_L2_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE 0x1 - - Bypass control for pcs-pma interface. EQ supplies, main master supply and ps for samp c2c - (OFFSET, MASK, VALUE) (0XFD409038, 0x00000040U ,0x00000040U) - RegMask = (SERDES_L2_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L2_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_ANA_BYP_15_OFFSET ,0x00000040U ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : L2_TM_ANA_BYP_12 @ 0XFD40902C</p> - - Enable Bypass for <7> of TM_ANA_BYPS_12 - PSU_SERDES_L2_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG 0x1 - - Bypass control for pcs-pma interface. Hsrx supply, hsrx des, and cdr enable controls - (OFFSET, MASK, VALUE) (0XFD40902C, 0x00000040U ,0x00000040U) - RegMask = (SERDES_L2_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L2_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L2_TM_ANA_BYP_12_OFFSET ,0x00000040U ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : L3_TM_RST_DLY @ 0XFD40D9A4</p> - - Delay apb reset by specified amount - PSU_SERDES_L3_TM_RST_DLY_APB_RST_DLY 0xFF - - reset delay for apb reset w.r.t pso of hsrx - (OFFSET, MASK, VALUE) (0XFD40D9A4, 0x000000FFU ,0x000000FFU) - RegMask = (SERDES_L3_TM_RST_DLY_APB_RST_DLY_MASK | 0 ); - - RegVal = ((0x000000FFU << SERDES_L3_TM_RST_DLY_APB_RST_DLY_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_RST_DLY_OFFSET ,0x000000FFU ,0x000000FFU); - /*############################################################################################################################ */ - - /*Register : L3_TM_ANA_BYP_15 @ 0XFD40D038</p> - - Enable Bypass for <7> of TM_ANA_BYPS_15 - PSU_SERDES_L3_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE 0x1 - - Bypass control for pcs-pma interface. EQ supplies, main master supply and ps for samp c2c - (OFFSET, MASK, VALUE) (0XFD40D038, 0x00000040U ,0x00000040U) - RegMask = (SERDES_L3_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_ANA_BYP_15_OFFSET ,0x00000040U ,0x00000040U); - /*############################################################################################################################ */ - - /*Register : L3_TM_ANA_BYP_12 @ 0XFD40D02C</p> - - Enable Bypass for <7> of TM_ANA_BYPS_12 - PSU_SERDES_L3_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG 0x1 - - Bypass control for pcs-pma interface. Hsrx supply, hsrx des, and cdr enable controls - (OFFSET, MASK, VALUE) (0XFD40D02C, 0x00000040U ,0x00000040U) - RegMask = (SERDES_L3_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_ANA_BYP_12_OFFSET ,0x00000040U ,0x00000040U); - /*############################################################################################################################ */ - - // : GT LANE SETTINGS - /*Register : ICM_CFG0 @ 0XFD410010</p> - - Controls UPHY Lane 0 protocol configuration. 0 - PowerDown, 1 - PCIe .0, 2 - Sata0, 3 - USB0, 4 - DP.1, 5 - SGMII0, 6 - Unuse - , 7 - Unused - PSU_SERDES_ICM_CFG0_L0_ICM_CFG 4 - - Controls UPHY Lane 1 protocol configuration. 0 - PowerDown, 1 - PCIe.1, 2 - Sata1, 3 - USB0, 4 - DP.0, 5 - SGMII1, 6 - Unused - 7 - Unused - PSU_SERDES_ICM_CFG0_L1_ICM_CFG 4 - - ICM Configuration Register 0 - (OFFSET, MASK, VALUE) (0XFD410010, 0x00000077U ,0x00000044U) - RegMask = (SERDES_ICM_CFG0_L0_ICM_CFG_MASK | SERDES_ICM_CFG0_L1_ICM_CFG_MASK | 0 ); - - RegVal = ((0x00000004U << SERDES_ICM_CFG0_L0_ICM_CFG_SHIFT - | 0x00000004U << SERDES_ICM_CFG0_L1_ICM_CFG_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_ICM_CFG0_OFFSET ,0x00000077U ,0x00000044U); - /*############################################################################################################################ */ - - /*Register : ICM_CFG1 @ 0XFD410014</p> - - Controls UPHY Lane 2 protocol configuration. 0 - PowerDown, 1 - PCIe.1, 2 - Sata0, 3 - USB0, 4 - DP.1, 5 - SGMII2, 6 - Unused - 7 - Unused - PSU_SERDES_ICM_CFG1_L2_ICM_CFG 3 - - Controls UPHY Lane 3 protocol configuration. 0 - PowerDown, 1 - PCIe.3, 2 - Sata1, 3 - USB1, 4 - DP.0, 5 - SGMII3, 6 - Unused - 7 - Unused - PSU_SERDES_ICM_CFG1_L3_ICM_CFG 2 - - ICM Configuration Register 1 - (OFFSET, MASK, VALUE) (0XFD410014, 0x00000077U ,0x00000023U) - RegMask = (SERDES_ICM_CFG1_L2_ICM_CFG_MASK | SERDES_ICM_CFG1_L3_ICM_CFG_MASK | 0 ); - - RegVal = ((0x00000003U << SERDES_ICM_CFG1_L2_ICM_CFG_SHIFT - | 0x00000002U << SERDES_ICM_CFG1_L3_ICM_CFG_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_ICM_CFG1_OFFSET ,0x00000077U ,0x00000023U); - /*############################################################################################################################ */ - - // : CHECKING PLL LOCK - // : ENABLE SERIAL DATA MUX DEEMPH - /*Register : L0_TXPMD_TM_45 @ 0XFD400CB4</p> - - Enable/disable DP post2 path - PSU_SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH 0x1 - - Override enable/disable of DP post2 path - PSU_SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH 0x1 - - Override enable/disable of DP post1 path - PSU_SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH 0x1 - - Enable/disable DP main path - PSU_SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH 0x1 - - Override enable/disable of DP main path - PSU_SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH 0x1 - - Post or pre or main DP path selection - (OFFSET, MASK, VALUE) (0XFD400CB4, 0x00000037U ,0x00000037U) - RegMask = (SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_MASK | SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_MASK | SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_MASK | SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_MASK | SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_SHIFT - | 0x00000001U << SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_SHIFT - | 0x00000001U << SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_SHIFT - | 0x00000001U << SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_SHIFT - | 0x00000001U << SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_TXPMD_TM_45_OFFSET ,0x00000037U ,0x00000037U); - /*############################################################################################################################ */ - - /*Register : L1_TXPMD_TM_45 @ 0XFD404CB4</p> - - Enable/disable DP post2 path - PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH 0x1 - - Override enable/disable of DP post2 path - PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH 0x1 - - Override enable/disable of DP post1 path - PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH 0x1 - - Enable/disable DP main path - PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH 0x1 - - Override enable/disable of DP main path - PSU_SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH 0x1 - - Post or pre or main DP path selection - (OFFSET, MASK, VALUE) (0XFD404CB4, 0x00000037U ,0x00000037U) - RegMask = (SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_MASK | SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_MASK | SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_MASK | SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_MASK | SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_SHIFT - | 0x00000001U << SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_SHIFT - | 0x00000001U << SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_SHIFT - | 0x00000001U << SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_SHIFT - | 0x00000001U << SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_TXPMD_TM_45_OFFSET ,0x00000037U ,0x00000037U); - /*############################################################################################################################ */ - - /*Register : L0_TX_ANA_TM_118 @ 0XFD4001D8</p> - - Test register force for enabling/disablign TX deemphasis bits <17:0> - PSU_SERDES_L0_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0 0x1 - - Enable Override of TX deemphasis - (OFFSET, MASK, VALUE) (0XFD4001D8, 0x00000001U ,0x00000001U) - RegMask = (SERDES_L0_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L0_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_TX_ANA_TM_118_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : L1_TX_ANA_TM_118 @ 0XFD4041D8</p> - - Test register force for enabling/disablign TX deemphasis bits <17:0> - PSU_SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0 0x1 - - Enable Override of TX deemphasis - (OFFSET, MASK, VALUE) (0XFD4041D8, 0x00000001U ,0x00000001U) - RegMask = (SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_TX_ANA_TM_118_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : L3_TX_ANA_TM_118 @ 0XFD40C1D8</p> - - Test register force for enabling/disablign TX deemphasis bits <17:0> - PSU_SERDES_L3_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0 0x1 - - Enable Override of TX deemphasis - (OFFSET, MASK, VALUE) (0XFD40C1D8, 0x00000001U ,0x00000001U) - RegMask = (SERDES_L3_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TX_ANA_TM_118_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - // : CDR AND RX EQUALIZATION SETTINGS - /*Register : L3_TM_CDR5 @ 0XFD40DC14</p> - - FPHL FSM accumulate cycles - PSU_SERDES_L3_TM_CDR5_FPHL_FSM_ACC_CYCLES 0x7 - - FFL Phase0 int gain aka 2ol SD update rate - PSU_SERDES_L3_TM_CDR5_FFL_PH0_INT_GAIN 0x6 - - Fast phase lock controls -- FSM accumulator cycle control and phase 0 int gain control. - (OFFSET, MASK, VALUE) (0XFD40DC14, 0x000000FFU ,0x000000E6U) - RegMask = (SERDES_L3_TM_CDR5_FPHL_FSM_ACC_CYCLES_MASK | SERDES_L3_TM_CDR5_FFL_PH0_INT_GAIN_MASK | 0 ); - - RegVal = ((0x00000007U << SERDES_L3_TM_CDR5_FPHL_FSM_ACC_CYCLES_SHIFT - | 0x00000006U << SERDES_L3_TM_CDR5_FFL_PH0_INT_GAIN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_CDR5_OFFSET ,0x000000FFU ,0x000000E6U); - /*############################################################################################################################ */ - - /*Register : L3_TM_CDR16 @ 0XFD40DC40</p> - - FFL Phase0 prop gain aka 1ol SD update rate - PSU_SERDES_L3_TM_CDR16_FFL_PH0_PROP_GAIN 0xC - - Fast phase lock controls -- phase 0 prop gain - (OFFSET, MASK, VALUE) (0XFD40DC40, 0x0000001FU ,0x0000000CU) - RegMask = (SERDES_L3_TM_CDR16_FFL_PH0_PROP_GAIN_MASK | 0 ); - - RegVal = ((0x0000000CU << SERDES_L3_TM_CDR16_FFL_PH0_PROP_GAIN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_CDR16_OFFSET ,0x0000001FU ,0x0000000CU); - /*############################################################################################################################ */ - - /*Register : L3_TM_EQ0 @ 0XFD40D94C</p> - - EQ stg 2 controls BYPASSED - PSU_SERDES_L3_TM_EQ0_EQ_STG2_CTRL_BYP 1 - - eq stg1 and stg2 controls - (OFFSET, MASK, VALUE) (0XFD40D94C, 0x00000020U ,0x00000020U) - RegMask = (SERDES_L3_TM_EQ0_EQ_STG2_CTRL_BYP_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TM_EQ0_EQ_STG2_CTRL_BYP_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_EQ0_OFFSET ,0x00000020U ,0x00000020U); - /*############################################################################################################################ */ - - /*Register : L3_TM_EQ1 @ 0XFD40D950</p> - - EQ STG2 RL PROG - PSU_SERDES_L3_TM_EQ1_EQ_STG2_RL_PROG 0x2 - - EQ stg 2 preamp mode val - PSU_SERDES_L3_TM_EQ1_EQ_STG2_PREAMP_MODE_VAL 0x1 - - eq stg1 and stg2 controls - (OFFSET, MASK, VALUE) (0XFD40D950, 0x00000007U ,0x00000006U) - RegMask = (SERDES_L3_TM_EQ1_EQ_STG2_RL_PROG_MASK | SERDES_L3_TM_EQ1_EQ_STG2_PREAMP_MODE_VAL_MASK | 0 ); - - RegVal = ((0x00000002U << SERDES_L3_TM_EQ1_EQ_STG2_RL_PROG_SHIFT - | 0x00000001U << SERDES_L3_TM_EQ1_EQ_STG2_PREAMP_MODE_VAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TM_EQ1_OFFSET ,0x00000007U ,0x00000006U); - /*############################################################################################################################ */ - - // : GEM SERDES SETTINGS - // : ENABLE PRE EMPHAIS AND VOLTAGE SWING - /*Register : L1_TXPMD_TM_48 @ 0XFD404CC0</p> - - Margining factor value - PSU_SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR 0 - - Margining factor - (OFFSET, MASK, VALUE) (0XFD404CC0, 0x0000001FU ,0x00000000U) - RegMask = (SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_TXPMD_TM_48_OFFSET ,0x0000001FU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : L0_TXPMD_TM_48 @ 0XFD400CC0</p> - - Margining factor value - PSU_SERDES_L0_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR 0 - - Margining factor - (OFFSET, MASK, VALUE) (0XFD400CC0, 0x0000001FU ,0x00000000U) - RegMask = (SERDES_L0_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L0_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_TXPMD_TM_48_OFFSET ,0x0000001FU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : L1_TX_ANA_TM_18 @ 0XFD404048</p> - - pipe_TX_Deemph. 0: -6dB de-emphasis, 1: -3.5dB de-emphasis, 2 : No de-emphasis, Others: reserved - PSU_SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0 0 - - Override for PIPE TX de-emphasis - (OFFSET, MASK, VALUE) (0XFD404048, 0x000000FFU ,0x00000000U) - RegMask = (SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L1_TX_ANA_TM_18_OFFSET ,0x000000FFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : L0_TX_ANA_TM_18 @ 0XFD400048</p> - - pipe_TX_Deemph. 0: -6dB de-emphasis, 1: -3.5dB de-emphasis, 2 : No de-emphasis, Others: reserved - PSU_SERDES_L0_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0 0 - - Override for PIPE TX de-emphasis - (OFFSET, MASK, VALUE) (0XFD400048, 0x000000FFU ,0x00000000U) - RegMask = (SERDES_L0_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_MASK | 0 ); - - RegVal = ((0x00000000U << SERDES_L0_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L0_TX_ANA_TM_18_OFFSET ,0x000000FFU ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : L3_TX_ANA_TM_18 @ 0XFD40C048</p> - - pipe_TX_Deemph. 0: -6dB de-emphasis, 1: -3.5dB de-emphasis, 2 : No de-emphasis, Others: reserved - PSU_SERDES_L3_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0 0x1 - - Override for PIPE TX de-emphasis - (OFFSET, MASK, VALUE) (0XFD40C048, 0x000000FFU ,0x00000001U) - RegMask = (SERDES_L3_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_MASK | 0 ); - - RegVal = ((0x00000001U << SERDES_L3_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SERDES_L3_TX_ANA_TM_18_OFFSET ,0x000000FFU ,0x00000001U); - /*############################################################################################################################ */ - - - return 1; -} -unsigned long psu_resetout_init_data() { - // : TAKING SERDES PERIPHERAL OUT OF RESET RESET - // : PUTTING USB0 IN RESET - /*Register : RST_LPD_TOP @ 0XFF5E023C</p> - - USB 0 reset for control registers - PSU_CRL_APB_RST_LPD_TOP_USB0_APB_RESET 0X0 - - Software control register for the LPD block. - (OFFSET, MASK, VALUE) (0XFF5E023C, 0x00000400U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_TOP_USB0_APB_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_TOP_USB0_APB_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_TOP_OFFSET ,0x00000400U ,0x00000000U); - /*############################################################################################################################ */ - - // : USB0 PIPE POWER PRESENT - /*Register : fpd_power_prsnt @ 0XFF9D0080</p> - - This bit is used to choose between PIPE power present and 1'b1 - PSU_USB3_0_FPD_POWER_PRSNT_OPTION 0X1 - - fpd_power_prsnt - (OFFSET, MASK, VALUE) (0XFF9D0080, 0x00000001U ,0x00000001U) - RegMask = (USB3_0_FPD_POWER_PRSNT_OPTION_MASK | 0 ); - - RegVal = ((0x00000001U << USB3_0_FPD_POWER_PRSNT_OPTION_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (USB3_0_FPD_POWER_PRSNT_OFFSET ,0x00000001U ,0x00000001U); - /*############################################################################################################################ */ - - /*Register : fpd_pipe_clk @ 0XFF9D007C</p> - - This bit is used to choose between PIPE clock coming from SerDes and the suspend clk - PSU_USB3_0_FPD_PIPE_CLK_OPTION 0x0 - - fpd_pipe_clk - (OFFSET, MASK, VALUE) (0XFF9D007C, 0x00000001U ,0x00000000U) - RegMask = (USB3_0_FPD_PIPE_CLK_OPTION_MASK | 0 ); - - RegVal = ((0x00000000U << USB3_0_FPD_PIPE_CLK_OPTION_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (USB3_0_FPD_PIPE_CLK_OFFSET ,0x00000001U ,0x00000000U); - /*############################################################################################################################ */ - - // : - /*Register : RST_LPD_TOP @ 0XFF5E023C</p> - - USB 0 sleep circuit reset - PSU_CRL_APB_RST_LPD_TOP_USB0_HIBERRESET 0X0 - - USB 0 reset - PSU_CRL_APB_RST_LPD_TOP_USB0_CORERESET 0X0 - - Software control register for the LPD block. - (OFFSET, MASK, VALUE) (0XFF5E023C, 0x00000140U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_MASK | CRL_APB_RST_LPD_TOP_USB0_CORERESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_SHIFT - | 0x00000000U << CRL_APB_RST_LPD_TOP_USB0_CORERESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_TOP_OFFSET ,0x00000140U ,0x00000000U); - /*############################################################################################################################ */ - - // : PUTTING GEM0 IN RESET - /*Register : RST_LPD_IOU0 @ 0XFF5E0230</p> - - GEM 3 reset - PSU_CRL_APB_RST_LPD_IOU0_GEM3_RESET 0X0 - - Software controlled reset for the GEMs - (OFFSET, MASK, VALUE) (0XFF5E0230, 0x00000008U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_IOU0_GEM3_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_IOU0_GEM3_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU0_OFFSET ,0x00000008U ,0x00000000U); - /*############################################################################################################################ */ - - // : PUTTING SATA IN RESET - /*Register : sata_misc_ctrl @ 0XFD3D0100</p> - - Sata PM clock control select - PSU_SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL 0x3 - - Misc Contorls for SATA.This register may only be modified during bootup (while SATA block is disabled) - (OFFSET, MASK, VALUE) (0XFD3D0100, 0x00000003U ,0x00000003U) - RegMask = (SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL_MASK | 0 ); - - RegVal = ((0x00000003U << SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SIOU_SATA_MISC_CTRL_OFFSET ,0x00000003U ,0x00000003U); - /*############################################################################################################################ */ - - /*Register : RST_FPD_TOP @ 0XFD1A0100</p> - - Sata block level reset - PSU_CRF_APB_RST_FPD_TOP_SATA_RESET 0X0 - - FPD Block level software controlled reset - (OFFSET, MASK, VALUE) (0XFD1A0100, 0x00000002U ,0x00000000U) - RegMask = (CRF_APB_RST_FPD_TOP_SATA_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_RST_FPD_TOP_SATA_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_RST_FPD_TOP_OFFSET ,0x00000002U ,0x00000000U); - /*############################################################################################################################ */ - - // : PUTTING DP IN RESET - /*Register : RST_FPD_TOP @ 0XFD1A0100</p> - - Display Port block level reset (includes DPDMA) - PSU_CRF_APB_RST_FPD_TOP_DP_RESET 0X0 - - FPD Block level software controlled reset - (OFFSET, MASK, VALUE) (0XFD1A0100, 0x00010000U ,0x00000000U) - RegMask = (CRF_APB_RST_FPD_TOP_DP_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_RST_FPD_TOP_DP_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_RST_FPD_TOP_OFFSET ,0x00010000U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DP_PHY_RESET @ 0XFD4A0200</p> - - Set to '1' to hold the GT in reset. Clear to release. - PSU_DP_DP_PHY_RESET_GT_RESET 0X0 - - Reset the transmitter PHY. - (OFFSET, MASK, VALUE) (0XFD4A0200, 0x00000002U ,0x00000000U) - RegMask = (DP_DP_PHY_RESET_GT_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << DP_DP_PHY_RESET_GT_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DP_DP_PHY_RESET_OFFSET ,0x00000002U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : DP_TX_PHY_POWER_DOWN @ 0XFD4A0238</p> - - Two bits per lane. When set to 11, moves the GT to power down mode. When set to 00, GT will be in active state. bits [1:0] - - ane0 Bits [3:2] - lane 1 - PSU_DP_DP_TX_PHY_POWER_DOWN_POWER_DWN 0X0 - - Control PHY Power down - (OFFSET, MASK, VALUE) (0XFD4A0238, 0x0000000FU ,0x00000000U) - RegMask = (DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_MASK | 0 ); - - RegVal = ((0x00000000U << DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DP_DP_TX_PHY_POWER_DOWN_OFFSET ,0x0000000FU ,0x00000000U); - /*############################################################################################################################ */ - - // : USB0 GFLADJ - /*Register : GUSB2PHYCFG @ 0XFE20C200</p> - - USB 2.0 Turnaround Time (USBTrdTim) Sets the turnaround time in PHY clocks. Specifies the response time for a MAC request to - he Packet FIFO Controller (PFC) to fetch data from the DFIFO (SPRAM). The following are the required values for the minimum S - C bus frequency of 60 MHz. USB turnaround time is a critical certification criteria when using long cables and five hub level - . The required values for this field: - 4'h5: When the MAC interface is 16-bit UTMI+. - 4'h9: When the MAC interface is 8-bit - UTMI+/ULPI. If SoC bus clock is less than 60 MHz, and USB turnaround time is not critical, this field can be set to a larger - alue. Note: This field is valid only in device mode. - PSU_USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM 0x9 - - Transceiver Delay: Enables a delay between the assertion of the UTMI/ULPI Transceiver Select signal (for HS) and the assertio - of the TxValid signal during a HS Chirp. When this bit is set to 1, a delay (of approximately 2.5 us) is introduced from the - time when the Transceiver Select is set to 2'b00 (HS) to the time the TxValid is driven to 0 for sending the chirp-K. This de - ay is required for some UTMI/ULPI PHYs. Note: - If you enable the hibernation feature when the device core comes out of power - off, you must re-initialize this bit with the appropriate value because the core does not save and restore this bit value dur - ng hibernation. - This bit is valid only in device mode. - PSU_USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY 0x0 - - Enable utmi_sleep_n and utmi_l1_suspend_n (EnblSlpM) The application uses this bit to control utmi_sleep_n and utmi_l1_suspen - _n assertion to the PHY in the L1 state. - 1'b0: utmi_sleep_n and utmi_l1_suspend_n assertion from the core is not transferre - to the external PHY. - 1'b1: utmi_sleep_n and utmi_l1_suspend_n assertion from the core is transferred to the external PHY. - ote: This bit must be set high for Port0 if PHY is used. Note: In Device mode - Before issuing any device endpoint command wh - n operating in 2.0 speeds, disable this bit and enable it after the command completes. Without disabling this bit, if a comma - d is issued when the device is in L1 state and if mac2_clk (utmi_clk/ulpi_clk) is gated off, the command will not get complet - d. - PSU_USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM 0x0 - - USB 2.0 High-Speed PHY or USB 1.1 Full-Speed Serial Transceiver Select The application uses this bit to select a high-speed P - Y or a full-speed transceiver. - 1'b0: USB 2.0 high-speed UTMI+ or ULPI PHY. This bit is always 0, with Write Only access. - - 'b1: USB 1.1 full-speed serial transceiver. This bit is always 1, with Write Only access. If both interface types are selecte - in coreConsultant (that is, parameters' values are not zero), the application uses this bit to select the active interface i - active, with Read-Write bit access. Note: USB 1.1 full-serial transceiver is not supported. This bit always reads as 1'b0. - PSU_USB3_0_XHCI_GUSB2PHYCFG_PHYSEL 0x0 - - Full-Speed Serial Interface Select (FSIntf) The application uses this bit to select a unidirectional or bidirectional USB 1.1 - full-speed serial transceiver interface. - 1'b0: 6-pin unidirectional full-speed serial interface. This bit is set to 0 with - ead Only access. - 1'b1: 3-pin bidirectional full-speed serial interface. This bit is set to 0 with Read Only access. Note: U - B 1.1 full-speed serial interface is not supported. This bit always reads as 1'b0. - PSU_USB3_0_XHCI_GUSB2PHYCFG_FSINTF 0x0 - - ULPI or UTMI+ Select (ULPI_UTMI_Sel) The application uses this bit to select a UTMI+ or ULPI Interface. - 1'b0: UTMI+ Interfa - e - 1'b1: ULPI Interface This bit is writable only if UTMI+ and ULPI is specified for High-Speed PHY Interface(s) in coreCons - ltant configuration (DWC_USB3_HSPHY_INTERFACE = 3). Otherwise, this bit is read-only and the value depends on the interface s - lected through DWC_USB3_HSPHY_INTERFACE. - PSU_USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL 0x1 - - PHY Interface (PHYIf) If UTMI+ is selected, the application uses this bit to configure the core to support a UTMI+ PHY with a - 8- or 16-bit interface. - 1'b0: 8 bits - 1'b1: 16 bits ULPI Mode: 1'b0 Note: - All the enabled 2.0 ports must have the same - lock frequency as Port0 clock frequency (utmi_clk[0]). - The UTMI 8-bit and 16-bit modes cannot be used together for differen - ports at the same time (that is, all the ports must be in 8-bit mode, or all of them must be in 16-bit mode, at a time). - I - any of the USB 2.0 ports is selected as ULPI port for operation, then all the USB 2.0 ports must be operating at 60 MHz. - PSU_USB3_0_XHCI_GUSB2PHYCFG_PHYIF 0x0 - - HS/FS Timeout Calibration (TOutCal) The number of PHY clocks, as indicated by the application in this field, is multiplied by - a bit-time factor; this factor is added to the high-speed/full-speed interpacket timeout duration in the core to account for - dditional delays introduced by the PHY. This may be required, since the delay introduced by the PHY in generating the linesta - e condition may vary among PHYs. The USB standard timeout value for high-speed operation is 736 to 816 (inclusive) bit times. - The USB standard timeout value for full-speed operation is 16 to 18 (inclusive) bit times. The application must program this - ield based on the speed of connection. The number of bit times added per PHY clock are: High-speed operation: - One 30-MHz PH - clock = 16 bit times - One 60-MHz PHY clock = 8 bit times Full-speed operation: - One 30-MHz PHY clock = 0.4 bit times - One - 60-MHz PHY clock = 0.2 bit times - One 48-MHz PHY clock = 0.25 bit times - PSU_USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL 0x7 - - Global USB2 PHY Configuration Register The application must program this register before starting any transactions on either - he SoC bus or the USB. In Device-only configurations, only one register is needed. In Host mode, per-port registers are imple - ented. - (OFFSET, MASK, VALUE) (0XFE20C200, 0x00003FBFU ,0x00002417U) - RegMask = (USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM_MASK | USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY_MASK | USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM_MASK | USB3_0_XHCI_GUSB2PHYCFG_PHYSEL_MASK | USB3_0_XHCI_GUSB2PHYCFG_FSINTF_MASK | USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL_MASK | USB3_0_XHCI_GUSB2PHYCFG_PHYIF_MASK | USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL_MASK | 0 ); - - RegVal = ((0x00000009U << USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM_SHIFT - | 0x00000000U << USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY_SHIFT - | 0x00000000U << USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM_SHIFT - | 0x00000000U << USB3_0_XHCI_GUSB2PHYCFG_PHYSEL_SHIFT - | 0x00000000U << USB3_0_XHCI_GUSB2PHYCFG_FSINTF_SHIFT - | 0x00000001U << USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL_SHIFT - | 0x00000000U << USB3_0_XHCI_GUSB2PHYCFG_PHYIF_SHIFT - | 0x00000007U << USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (USB3_0_XHCI_GUSB2PHYCFG_OFFSET ,0x00003FBFU ,0x00002417U); - /*############################################################################################################################ */ - - /*Register : GFLADJ @ 0XFE20C630</p> - - This field indicates the frame length adjustment to be applied when SOF/ITP counter is running on the ref_clk. This register - alue is used to adjust the ITP interval when GCTL[SOFITPSYNC] is set to '1'; SOF and ITP interval when GLADJ.GFLADJ_REFCLK_LP - _SEL is set to '1'. This field must be programmed to a non-zero value only if GFLADJ_REFCLK_LPM_SEL is set to '1' or GCTL.SOF - TPSYNC is set to '1'. The value is derived as follows: FLADJ_REF_CLK_FLADJ=((125000/ref_clk_period_integer)-(125000/ref_clk_p - riod)) * ref_clk_period where - the ref_clk_period_integer is the integer value of the ref_clk period got by truncating the d - cimal (fractional) value that is programmed in the GUCTL.REF_CLK_PERIOD field. - the ref_clk_period is the ref_clk period inc - uding the fractional value. Examples: If the ref_clk is 24 MHz then - GUCTL.REF_CLK_PERIOD = 41 - GFLADJ.GLADJ_REFCLK_FLADJ = - ((125000/41)-(125000/41.6666))*41.6666 = 2032 (ignoring the fractional value) If the ref_clk is 48 MHz then - GUCTL.REF_CLK_P - RIOD = 20 - GFLADJ.GLADJ_REFCLK_FLADJ = ((125000/20)-(125000/20.8333))*20.8333 = 5208 (ignoring the fractional value) - PSU_USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ 0x0 - - Global Frame Length Adjustment Register This register provides options for the software to control the core behavior with res - ect to SOF (Start of Frame) and ITP (Isochronous Timestamp Packet) timers and frame timer functionality. It provides an optio - to override the fladj_30mhz_reg sideband signal. In addition, it enables running SOF or ITP frame timer counters completely - rom the ref_clk. This facilitates hardware LPM in host mode with the SOF or ITP counters being run from the ref_clk signal. - (OFFSET, MASK, VALUE) (0XFE20C630, 0x003FFF00U ,0x00000000U) - RegMask = (USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ_MASK | 0 ); - - RegVal = ((0x00000000U << USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (USB3_0_XHCI_GFLADJ_OFFSET ,0x003FFF00U ,0x00000000U); - /*############################################################################################################################ */ - - // : UPDATING TWO PCIE REGISTERS DEFAULT VALUES, AS THESE REGISTERS HAVE INCORRECT RESET VALUES IN SILICON. - /*Register : ATTR_25 @ 0XFD480064</p> - - If TRUE Completion Timeout Disable is supported. This is required to be TRUE for Endpoint and either setting allowed for Root - ports. Drives Device Capability 2 [4]; EP=0x0001; RP=0x0001 - PSU_PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED 0X1 - - ATTR_25 - (OFFSET, MASK, VALUE) (0XFD480064, 0x00000200U ,0x00000200U) - RegMask = (PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED_MASK | 0 ); - - RegVal = ((0x00000001U << PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (PCIE_ATTRIB_ATTR_25_OFFSET ,0x00000200U ,0x00000200U); - /*############################################################################################################################ */ - - // : CHECK PLL LOCK FOR LANE1 - /*Register : L1_PLL_STATUS_READ_1 @ 0XFD4063E4</p> - - Status Read value of PLL Lock - PSU_SERDES_L1_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ 1 - (OFFSET, MASK, VALUE) (0XFD4063E4, 0x00000010U ,0x00000010U) */ - mask_poll(SERDES_L1_PLL_STATUS_READ_1_OFFSET,0x00000010U); - - /*############################################################################################################################ */ - - // : CHECK PLL LOCK FOR LANE2 - /*Register : L2_PLL_STATUS_READ_1 @ 0XFD40A3E4</p> - - Status Read value of PLL Lock - PSU_SERDES_L2_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ 1 - (OFFSET, MASK, VALUE) (0XFD40A3E4, 0x00000010U ,0x00000010U) */ - mask_poll(SERDES_L2_PLL_STATUS_READ_1_OFFSET,0x00000010U); - - /*############################################################################################################################ */ - - // : CHECK PLL LOCK FOR LANE3 - /*Register : L3_PLL_STATUS_READ_1 @ 0XFD40E3E4</p> - - Status Read value of PLL Lock - PSU_SERDES_L3_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ 1 - (OFFSET, MASK, VALUE) (0XFD40E3E4, 0x00000010U ,0x00000010U) */ - mask_poll(SERDES_L3_PLL_STATUS_READ_1_OFFSET,0x00000010U); - - /*############################################################################################################################ */ - - // : SATA AHCI VENDOR SETTING - /*Register : PP2C @ 0XFD0C00AC</p> - - CIBGMN: COMINIT Burst Gap Minimum. - PSU_SATA_AHCI_VENDOR_PP2C_CIBGMN 0x18 - - CIBGMX: COMINIT Burst Gap Maximum. - PSU_SATA_AHCI_VENDOR_PP2C_CIBGMX 0x40 - - CIBGN: COMINIT Burst Gap Nominal. - PSU_SATA_AHCI_VENDOR_PP2C_CIBGN 0x18 - - CINMP: COMINIT Negate Minimum Period. - PSU_SATA_AHCI_VENDOR_PP2C_CINMP 0x28 - - PP2C - Port Phy2Cfg Register. This register controls the configuration of the Phy Control OOB timing for the COMINIT paramete - s for either Port 0 or Port 1. The Port configured is controlled by the value programmed into the Port Config Register. - (OFFSET, MASK, VALUE) (0XFD0C00AC, 0xFFFFFFFFU ,0x28184018U) - RegMask = (SATA_AHCI_VENDOR_PP2C_CIBGMN_MASK | SATA_AHCI_VENDOR_PP2C_CIBGMX_MASK | SATA_AHCI_VENDOR_PP2C_CIBGN_MASK | SATA_AHCI_VENDOR_PP2C_CINMP_MASK | 0 ); - - RegVal = ((0x00000018U << SATA_AHCI_VENDOR_PP2C_CIBGMN_SHIFT - | 0x00000040U << SATA_AHCI_VENDOR_PP2C_CIBGMX_SHIFT - | 0x00000018U << SATA_AHCI_VENDOR_PP2C_CIBGN_SHIFT - | 0x00000028U << SATA_AHCI_VENDOR_PP2C_CINMP_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SATA_AHCI_VENDOR_PP2C_OFFSET ,0xFFFFFFFFU ,0x28184018U); - /*############################################################################################################################ */ - - /*Register : PP3C @ 0XFD0C00B0</p> - - CWBGMN: COMWAKE Burst Gap Minimum. - PSU_SATA_AHCI_VENDOR_PP3C_CWBGMN 0x06 - - CWBGMX: COMWAKE Burst Gap Maximum. - PSU_SATA_AHCI_VENDOR_PP3C_CWBGMX 0x14 - - CWBGN: COMWAKE Burst Gap Nominal. - PSU_SATA_AHCI_VENDOR_PP3C_CWBGN 0x08 - - CWNMP: COMWAKE Negate Minimum Period. - PSU_SATA_AHCI_VENDOR_PP3C_CWNMP 0x0E - - PP3C - Port Phy3CfgRegister. This register controls the configuration of the Phy Control OOB timing for the COMWAKE parameter - for either Port 0 or Port 1. The Port configured is controlled by the value programmed into the Port Config Register. - (OFFSET, MASK, VALUE) (0XFD0C00B0, 0xFFFFFFFFU ,0x0E081406U) - RegMask = (SATA_AHCI_VENDOR_PP3C_CWBGMN_MASK | SATA_AHCI_VENDOR_PP3C_CWBGMX_MASK | SATA_AHCI_VENDOR_PP3C_CWBGN_MASK | SATA_AHCI_VENDOR_PP3C_CWNMP_MASK | 0 ); - - RegVal = ((0x00000006U << SATA_AHCI_VENDOR_PP3C_CWBGMN_SHIFT - | 0x00000014U << SATA_AHCI_VENDOR_PP3C_CWBGMX_SHIFT - | 0x00000008U << SATA_AHCI_VENDOR_PP3C_CWBGN_SHIFT - | 0x0000000EU << SATA_AHCI_VENDOR_PP3C_CWNMP_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SATA_AHCI_VENDOR_PP3C_OFFSET ,0xFFFFFFFFU ,0x0E081406U); - /*############################################################################################################################ */ - - /*Register : PP4C @ 0XFD0C00B4</p> - - BMX: COM Burst Maximum. - PSU_SATA_AHCI_VENDOR_PP4C_BMX 0x13 - - BNM: COM Burst Nominal. - PSU_SATA_AHCI_VENDOR_PP4C_BNM 0x08 - - SFD: Signal Failure Detection, if the signal detection de-asserts for a time greater than this then the OOB detector will det - rmine this is a line idle and cause the PhyInit state machine to exit the Phy Ready State. A value of zero disables the Signa - Failure Detector. The value is based on the OOB Detector Clock typically (PMCLK Clock Period) * SFD giving a nominal time of - 500ns based on a 150MHz PMCLK. - PSU_SATA_AHCI_VENDOR_PP4C_SFD 0x4A - - PTST: Partial to Slumber timer value, specific delay the controller should apply while in partial before entering slumber. Th - value is bases on the system clock divided by 128, total delay = (Sys Clock Period) * PTST * 128 - PSU_SATA_AHCI_VENDOR_PP4C_PTST 0x06 - - PP4C - Port Phy4Cfg Register. This register controls the configuration of the Phy Control Burst timing for the COM parameters - for either Port 0 or Port 1. The Port configured is controlled by the value programmed into the Port Config Register. - (OFFSET, MASK, VALUE) (0XFD0C00B4, 0xFFFFFFFFU ,0x064A0813U) - RegMask = (SATA_AHCI_VENDOR_PP4C_BMX_MASK | SATA_AHCI_VENDOR_PP4C_BNM_MASK | SATA_AHCI_VENDOR_PP4C_SFD_MASK | SATA_AHCI_VENDOR_PP4C_PTST_MASK | 0 ); - - RegVal = ((0x00000013U << SATA_AHCI_VENDOR_PP4C_BMX_SHIFT - | 0x00000008U << SATA_AHCI_VENDOR_PP4C_BNM_SHIFT - | 0x0000004AU << SATA_AHCI_VENDOR_PP4C_SFD_SHIFT - | 0x00000006U << SATA_AHCI_VENDOR_PP4C_PTST_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SATA_AHCI_VENDOR_PP4C_OFFSET ,0xFFFFFFFFU ,0x064A0813U); - /*############################################################################################################################ */ - - /*Register : PP5C @ 0XFD0C00B8</p> - - RIT: Retry Interval Timer. The calculated value divided by two, the lower digit of precision is not needed. - PSU_SATA_AHCI_VENDOR_PP5C_RIT 0xC96A4 - - RCT: Rate Change Timer, a value based on the 54.2us for which a SATA device will transmit at a fixed rate ALIGNp after OOB ha - completed, for a fast SERDES it is suggested that this value be 54.2us / 4 - PSU_SATA_AHCI_VENDOR_PP5C_RCT 0x3FF - - PP5C - Port Phy5Cfg Register. This register controls the configuration of the Phy Control Retry Interval timing for either Po - t 0 or Port 1. The Port configured is controlled by the value programmed into the Port Config Register. - (OFFSET, MASK, VALUE) (0XFD0C00B8, 0xFFFFFFFFU ,0x3FFC96A4U) - RegMask = (SATA_AHCI_VENDOR_PP5C_RIT_MASK | SATA_AHCI_VENDOR_PP5C_RCT_MASK | 0 ); - - RegVal = ((0x000C96A4U << SATA_AHCI_VENDOR_PP5C_RIT_SHIFT - | 0x000003FFU << SATA_AHCI_VENDOR_PP5C_RCT_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (SATA_AHCI_VENDOR_PP5C_OFFSET ,0xFFFFFFFFU ,0x3FFC96A4U); - /*############################################################################################################################ */ - - - return 1; -} -unsigned long psu_resetin_init_data() { - // : PUTTING SERDES PERIPHERAL IN RESET - // : PUTTING USB0 IN RESET - /*Register : RST_LPD_TOP @ 0XFF5E023C</p> - - USB 0 reset for control registers - PSU_CRL_APB_RST_LPD_TOP_USB0_APB_RESET 0X1 - - USB 0 sleep circuit reset - PSU_CRL_APB_RST_LPD_TOP_USB0_HIBERRESET 0X1 - - USB 0 reset - PSU_CRL_APB_RST_LPD_TOP_USB0_CORERESET 0X1 - - Software control register for the LPD block. - (OFFSET, MASK, VALUE) (0XFF5E023C, 0x00000540U ,0x00000540U) - RegMask = (CRL_APB_RST_LPD_TOP_USB0_APB_RESET_MASK | CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_MASK | CRL_APB_RST_LPD_TOP_USB0_CORERESET_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_RST_LPD_TOP_USB0_APB_RESET_SHIFT - | 0x00000001U << CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_SHIFT - | 0x00000001U << CRL_APB_RST_LPD_TOP_USB0_CORERESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_TOP_OFFSET ,0x00000540U ,0x00000540U); - /*############################################################################################################################ */ - - // : PUTTING GEM0 IN RESET - /*Register : RST_LPD_IOU0 @ 0XFF5E0230</p> - - GEM 3 reset - PSU_CRL_APB_RST_LPD_IOU0_GEM3_RESET 0X1 - - Software controlled reset for the GEMs - (OFFSET, MASK, VALUE) (0XFF5E0230, 0x00000008U ,0x00000008U) - RegMask = (CRL_APB_RST_LPD_IOU0_GEM3_RESET_MASK | 0 ); - - RegVal = ((0x00000001U << CRL_APB_RST_LPD_IOU0_GEM3_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_IOU0_OFFSET ,0x00000008U ,0x00000008U); - /*############################################################################################################################ */ - - // : PUTTING SATA IN RESET - /*Register : RST_FPD_TOP @ 0XFD1A0100</p> - - Sata block level reset - PSU_CRF_APB_RST_FPD_TOP_SATA_RESET 0X1 - - FPD Block level software controlled reset - (OFFSET, MASK, VALUE) (0XFD1A0100, 0x00000002U ,0x00000002U) - RegMask = (CRF_APB_RST_FPD_TOP_SATA_RESET_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_RST_FPD_TOP_SATA_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_RST_FPD_TOP_OFFSET ,0x00000002U ,0x00000002U); - /*############################################################################################################################ */ - - // : PUTTING DP IN RESET - /*Register : DP_TX_PHY_POWER_DOWN @ 0XFD4A0238</p> - - Two bits per lane. When set to 11, moves the GT to power down mode. When set to 00, GT will be in active state. bits [1:0] - - ane0 Bits [3:2] - lane 1 - PSU_DP_DP_TX_PHY_POWER_DOWN_POWER_DWN 0XA - - Control PHY Power down - (OFFSET, MASK, VALUE) (0XFD4A0238, 0x0000000FU ,0x0000000AU) - RegMask = (DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_MASK | 0 ); - - RegVal = ((0x0000000AU << DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DP_DP_TX_PHY_POWER_DOWN_OFFSET ,0x0000000FU ,0x0000000AU); - /*############################################################################################################################ */ - - /*Register : DP_PHY_RESET @ 0XFD4A0200</p> - - Set to '1' to hold the GT in reset. Clear to release. - PSU_DP_DP_PHY_RESET_GT_RESET 0X1 - - Reset the transmitter PHY. - (OFFSET, MASK, VALUE) (0XFD4A0200, 0x00000002U ,0x00000002U) - RegMask = (DP_DP_PHY_RESET_GT_RESET_MASK | 0 ); - - RegVal = ((0x00000001U << DP_DP_PHY_RESET_GT_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (DP_DP_PHY_RESET_OFFSET ,0x00000002U ,0x00000002U); - /*############################################################################################################################ */ - - /*Register : RST_FPD_TOP @ 0XFD1A0100</p> - - Display Port block level reset (includes DPDMA) - PSU_CRF_APB_RST_FPD_TOP_DP_RESET 0X1 - - FPD Block level software controlled reset - (OFFSET, MASK, VALUE) (0XFD1A0100, 0x00010000U ,0x00010000U) - RegMask = (CRF_APB_RST_FPD_TOP_DP_RESET_MASK | 0 ); - - RegVal = ((0x00000001U << CRF_APB_RST_FPD_TOP_DP_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_RST_FPD_TOP_OFFSET ,0x00010000U ,0x00010000U); - /*############################################################################################################################ */ - - - return 1; -} -unsigned long psu_ps_pl_isolation_removal_data() { - // : AFI RESET - /*Register : RST_FPD_TOP @ 0XFD1A0100</p> - - AF_FM0 block level reset - PSU_CRF_APB_RST_FPD_TOP_AFI_FM0_RESET 0 - - AF_FM1 block level reset - PSU_CRF_APB_RST_FPD_TOP_AFI_FM1_RESET 0 - - AF_FM2 block level reset - PSU_CRF_APB_RST_FPD_TOP_AFI_FM2_RESET 0 - - AF_FM3 block level reset - PSU_CRF_APB_RST_FPD_TOP_AFI_FM3_RESET 0 - - AF_FM4 block level reset - PSU_CRF_APB_RST_FPD_TOP_AFI_FM4_RESET 0 - - AF_FM5 block level reset - PSU_CRF_APB_RST_FPD_TOP_AFI_FM5_RESET 0 - - FPD Block level software controlled reset - (OFFSET, MASK, VALUE) (0XFD1A0100, 0x00001F80U ,0x00000000U) - RegMask = (CRF_APB_RST_FPD_TOP_AFI_FM0_RESET_MASK | CRF_APB_RST_FPD_TOP_AFI_FM1_RESET_MASK | CRF_APB_RST_FPD_TOP_AFI_FM2_RESET_MASK | CRF_APB_RST_FPD_TOP_AFI_FM3_RESET_MASK | CRF_APB_RST_FPD_TOP_AFI_FM4_RESET_MASK | CRF_APB_RST_FPD_TOP_AFI_FM5_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRF_APB_RST_FPD_TOP_AFI_FM0_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_AFI_FM1_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_AFI_FM2_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_AFI_FM3_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_AFI_FM4_RESET_SHIFT - | 0x00000000U << CRF_APB_RST_FPD_TOP_AFI_FM5_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRF_APB_RST_FPD_TOP_OFFSET ,0x00001F80U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : RST_LPD_TOP @ 0XFF5E023C</p> - - AFI FM 6 - PSU_CRL_APB_RST_LPD_TOP_AFI_FM6_RESET 0 - - Software control register for the LPD block. - (OFFSET, MASK, VALUE) (0XFF5E023C, 0x00080000U ,0x00000000U) - RegMask = (CRL_APB_RST_LPD_TOP_AFI_FM6_RESET_MASK | 0 ); - - RegVal = ((0x00000000U << CRL_APB_RST_LPD_TOP_AFI_FM6_RESET_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (CRL_APB_RST_LPD_TOP_OFFSET ,0x00080000U ,0x00000000U); - /*############################################################################################################################ */ - - // : AFIFM INTERFACE WIDTH - /*Register : afi_fs @ 0XFD615000</p> - - Select the 32/64/128-bit data width selection for the Slave 0 00: 32-bit AXI data width (default) 01: 64-bit AXI data width 1 - : 128-bit AXI data width 11: reserved - PSU_FPD_SLCR_AFI_FS_DW_SS0_SEL 0x2 - - Select the 32/64/128-bit data width selection for the Slave 1 00: 32-bit AXI data width (default) 01: 64-bit AXI data width 1 - : 128-bit AXI data width 11: reserved - PSU_FPD_SLCR_AFI_FS_DW_SS1_SEL 0x2 - - afi fs SLCR control register. This register is static and should not be modified during operation. - (OFFSET, MASK, VALUE) (0XFD615000, 0x00000F00U ,0x00000A00U) - RegMask = (FPD_SLCR_AFI_FS_DW_SS0_SEL_MASK | FPD_SLCR_AFI_FS_DW_SS1_SEL_MASK | 0 ); - - RegVal = ((0x00000002U << FPD_SLCR_AFI_FS_DW_SS0_SEL_SHIFT - | 0x00000002U << FPD_SLCR_AFI_FS_DW_SS1_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (FPD_SLCR_AFI_FS_OFFSET ,0x00000F00U ,0x00000A00U); - /*############################################################################################################################ */ - - /*Register : afi_fs @ 0XFF419000</p> - - Select the 32/64/128-bit data width selection for the Slave 0 00: 32-bit AXI data width (default) 01: 64-bit AXI data width 1 - : 128-bit AXI data width 11: reserved - PSU_LPD_SLCR_AFI_FS_DW_SS2_SEL 0x2 - - afi fs SLCR control register. Do not change the bits durin - (OFFSET, MASK, VALUE) (0XFF419000, 0x00000300U ,0x00000200U) - RegMask = (LPD_SLCR_AFI_FS_DW_SS2_SEL_MASK | 0 ); - - RegVal = ((0x00000002U << LPD_SLCR_AFI_FS_DW_SS2_SEL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (LPD_SLCR_AFI_FS_OFFSET ,0x00000300U ,0x00000200U); - /*############################################################################################################################ */ - - /*Register : AFIFM_RDCTRL @ 0XFD360000</p> - - Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled - PSU_AFIFM0_AFIFM_RDCTRL_FABRIC_WIDTH 0x0 - - Read Channel Control Register - (OFFSET, MASK, VALUE) (0XFD360000, 0x00000003U ,0x00000000U) - RegMask = (AFIFM0_AFIFM_RDCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM0_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM0_AFIFM_RDCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_RDCTRL @ 0XFD370000</p> - - Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled - PSU_AFIFM1_AFIFM_RDCTRL_FABRIC_WIDTH 0x0 - - Read Channel Control Register - (OFFSET, MASK, VALUE) (0XFD370000, 0x00000003U ,0x00000000U) - RegMask = (AFIFM1_AFIFM_RDCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM1_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM1_AFIFM_RDCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_RDCTRL @ 0XFD380000</p> - - Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled - PSU_AFIFM2_AFIFM_RDCTRL_FABRIC_WIDTH 0x0 - - Read Channel Control Register - (OFFSET, MASK, VALUE) (0XFD380000, 0x00000003U ,0x00000000U) - RegMask = (AFIFM2_AFIFM_RDCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM2_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM2_AFIFM_RDCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_RDCTRL @ 0XFD390000</p> - - Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled - PSU_AFIFM3_AFIFM_RDCTRL_FABRIC_WIDTH 0x0 - - Read Channel Control Register - (OFFSET, MASK, VALUE) (0XFD390000, 0x00000003U ,0x00000000U) - RegMask = (AFIFM3_AFIFM_RDCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM3_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM3_AFIFM_RDCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_RDCTRL @ 0XFD3A0000</p> - - Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled - PSU_AFIFM4_AFIFM_RDCTRL_FABRIC_WIDTH 0x0 - - Read Channel Control Register - (OFFSET, MASK, VALUE) (0XFD3A0000, 0x00000003U ,0x00000000U) - RegMask = (AFIFM4_AFIFM_RDCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM4_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM4_AFIFM_RDCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_RDCTRL @ 0XFD3B0000</p> - - Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled - PSU_AFIFM5_AFIFM_RDCTRL_FABRIC_WIDTH 0x0 - - Read Channel Control Register - (OFFSET, MASK, VALUE) (0XFD3B0000, 0x00000003U ,0x00000000U) - RegMask = (AFIFM5_AFIFM_RDCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM5_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM5_AFIFM_RDCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_RDCTRL @ 0XFF9B0000</p> - - Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled - PSU_AFIFM6_AFIFM_RDCTRL_FABRIC_WIDTH 0x0 - - Read Channel Control Register - (OFFSET, MASK, VALUE) (0XFF9B0000, 0x00000003U ,0x00000000U) - RegMask = (AFIFM6_AFIFM_RDCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM6_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM6_AFIFM_RDCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_WRCTRL @ 0XFD360014</p> - - Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled - PSU_AFIFM0_AFIFM_WRCTRL_FABRIC_WIDTH 0x0 - - Write Channel Control Register - (OFFSET, MASK, VALUE) (0XFD360014, 0x00000003U ,0x00000000U) - RegMask = (AFIFM0_AFIFM_WRCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM0_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM0_AFIFM_WRCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_WRCTRL @ 0XFD370014</p> - - Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled - PSU_AFIFM1_AFIFM_WRCTRL_FABRIC_WIDTH 0x0 - - Write Channel Control Register - (OFFSET, MASK, VALUE) (0XFD370014, 0x00000003U ,0x00000000U) - RegMask = (AFIFM1_AFIFM_WRCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM1_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM1_AFIFM_WRCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_WRCTRL @ 0XFD380014</p> - - Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled - PSU_AFIFM2_AFIFM_WRCTRL_FABRIC_WIDTH 0x0 - - Write Channel Control Register - (OFFSET, MASK, VALUE) (0XFD380014, 0x00000003U ,0x00000000U) - RegMask = (AFIFM2_AFIFM_WRCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM2_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM2_AFIFM_WRCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_WRCTRL @ 0XFD390014</p> - - Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled - PSU_AFIFM3_AFIFM_WRCTRL_FABRIC_WIDTH 0x0 - - Write Channel Control Register - (OFFSET, MASK, VALUE) (0XFD390014, 0x00000003U ,0x00000000U) - RegMask = (AFIFM3_AFIFM_WRCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM3_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM3_AFIFM_WRCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_WRCTRL @ 0XFD3A0014</p> - - Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled - PSU_AFIFM4_AFIFM_WRCTRL_FABRIC_WIDTH 0x0 - - Write Channel Control Register - (OFFSET, MASK, VALUE) (0XFD3A0014, 0x00000003U ,0x00000000U) - RegMask = (AFIFM4_AFIFM_WRCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM4_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM4_AFIFM_WRCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_WRCTRL @ 0XFD3B0014</p> - - Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled - PSU_AFIFM5_AFIFM_WRCTRL_FABRIC_WIDTH 0x0 - - Write Channel Control Register - (OFFSET, MASK, VALUE) (0XFD3B0014, 0x00000003U ,0x00000000U) - RegMask = (AFIFM5_AFIFM_WRCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM5_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM5_AFIFM_WRCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - /*Register : AFIFM_WRCTRL @ 0XFF9B0014</p> - - Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled - PSU_AFIFM6_AFIFM_WRCTRL_FABRIC_WIDTH 0x0 - - Write Channel Control Register - (OFFSET, MASK, VALUE) (0XFF9B0014, 0x00000003U ,0x00000000U) - RegMask = (AFIFM6_AFIFM_WRCTRL_FABRIC_WIDTH_MASK | 0 ); - - RegVal = ((0x00000000U << AFIFM6_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (AFIFM6_AFIFM_WRCTRL_OFFSET ,0x00000003U ,0x00000000U); - /*############################################################################################################################ */ - - // : PS-PL POWER UP REQUEST - /*Register : REQ_PWRUP_INT_EN @ 0XFFD80118</p> - - Power-up Request Interrupt Enable for PL - PSU_PMU_GLOBAL_REQ_PWRUP_INT_EN_PL 1 - - Power-up Request Interrupt Enable Register. Writing a 1 to this location will unmask the interrupt. - (OFFSET, MASK, VALUE) (0XFFD80118, 0x00800000U ,0x00800000U) - RegMask = (PMU_GLOBAL_REQ_PWRUP_INT_EN_PL_MASK | 0 ); - - RegVal = ((0x00000001U << PMU_GLOBAL_REQ_PWRUP_INT_EN_PL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (PMU_GLOBAL_REQ_PWRUP_INT_EN_OFFSET ,0x00800000U ,0x00800000U); - /*############################################################################################################################ */ - - /*Register : REQ_PWRUP_TRIG @ 0XFFD80120</p> - - Power-up Request Trigger for PL - PSU_PMU_GLOBAL_REQ_PWRUP_TRIG_PL 1 - - Power-up Request Trigger Register. A write of one to this location will generate a power-up request to the PMU. - (OFFSET, MASK, VALUE) (0XFFD80120, 0x00800000U ,0x00800000U) - RegMask = (PMU_GLOBAL_REQ_PWRUP_TRIG_PL_MASK | 0 ); - - RegVal = ((0x00000001U << PMU_GLOBAL_REQ_PWRUP_TRIG_PL_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (PMU_GLOBAL_REQ_PWRUP_TRIG_OFFSET ,0x00800000U ,0x00800000U); - /*############################################################################################################################ */ - - // : POLL ON PL POWER STATUS - /*Register : REQ_PWRUP_STATUS @ 0XFFD80110</p> - - Power-up Request Status for PL - PSU_PMU_GLOBAL_REQ_PWRUP_STATUS_PL 1 - (OFFSET, MASK, VALUE) (0XFFD80110, 0x00800000U ,0x00000000U) */ - mask_pollOnValue(PMU_GLOBAL_REQ_PWRUP_STATUS_OFFSET,0x00800000U,0x00000000U); - - /*############################################################################################################################ */ - - - return 1; -} -unsigned long psu_ps_pl_reset_config_data() { - // : PS PL RESET SEQUENCE - // : FABRIC RESET USING EMIO - /*Register : MASK_DATA_5_MSW @ 0XFF0A002C</p> - - Operation is the same as MASK_DATA_0_LSW[MASK_0_LSW] - PSU_GPIO_MASK_DATA_5_MSW_MASK_5_MSW 0x8000 - - Maskable Output Data (GPIO Bank5, EMIO, Upper 16bits) - (OFFSET, MASK, VALUE) (0XFF0A002C, 0xFFFF0000U ,0x80000000U) - RegMask = (GPIO_MASK_DATA_5_MSW_MASK_5_MSW_MASK | 0 ); - - RegVal = ((0x00008000U << GPIO_MASK_DATA_5_MSW_MASK_5_MSW_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (GPIO_MASK_DATA_5_MSW_OFFSET ,0xFFFF0000U ,0x80000000U); - /*############################################################################################################################ */ - - /*Register : DIRM_5 @ 0XFF0A0344</p> - - Operation is the same as DIRM_0[DIRECTION_0] - PSU_GPIO_DIRM_5_DIRECTION_5 0x80000000 - - Direction mode (GPIO Bank5, EMIO) - (OFFSET, MASK, VALUE) (0XFF0A0344, 0xFFFFFFFFU ,0x80000000U) - RegMask = (GPIO_DIRM_5_DIRECTION_5_MASK | 0 ); - - RegVal = ((0x80000000U << GPIO_DIRM_5_DIRECTION_5_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (GPIO_DIRM_5_OFFSET ,0xFFFFFFFFU ,0x80000000U); - /*############################################################################################################################ */ - - /*Register : OEN_5 @ 0XFF0A0348</p> - - Operation is the same as OEN_0[OP_ENABLE_0] - PSU_GPIO_OEN_5_OP_ENABLE_5 0x80000000 - - Output enable (GPIO Bank5, EMIO) - (OFFSET, MASK, VALUE) (0XFF0A0348, 0xFFFFFFFFU ,0x80000000U) - RegMask = (GPIO_OEN_5_OP_ENABLE_5_MASK | 0 ); - - RegVal = ((0x80000000U << GPIO_OEN_5_OP_ENABLE_5_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (GPIO_OEN_5_OFFSET ,0xFFFFFFFFU ,0x80000000U); - /*############################################################################################################################ */ - - /*Register : DATA_5 @ 0XFF0A0054</p> - - Output Data - PSU_GPIO_DATA_5_DATA_5 0x80000000 - - Output Data (GPIO Bank5, EMIO) - (OFFSET, MASK, VALUE) (0XFF0A0054, 0xFFFFFFFFU ,0x80000000U) - RegMask = (GPIO_DATA_5_DATA_5_MASK | 0 ); - - RegVal = ((0x80000000U << GPIO_DATA_5_DATA_5_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (GPIO_DATA_5_OFFSET ,0xFFFFFFFFU ,0x80000000U); - /*############################################################################################################################ */ - - mask_delay(1); - - /*############################################################################################################################ */ - - // : FABRIC RESET USING DATA_5 TOGGLE - /*Register : DATA_5 @ 0XFF0A0054</p> - - Output Data - PSU_GPIO_DATA_5_DATA_5 0X00000000 - - Output Data (GPIO Bank5, EMIO) - (OFFSET, MASK, VALUE) (0XFF0A0054, 0xFFFFFFFFU ,0x00000000U) - RegMask = (GPIO_DATA_5_DATA_5_MASK | 0 ); - - RegVal = ((0x00000000U << GPIO_DATA_5_DATA_5_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (GPIO_DATA_5_OFFSET ,0xFFFFFFFFU ,0x00000000U); - /*############################################################################################################################ */ - - mask_delay(1); - - /*############################################################################################################################ */ - - // : FABRIC RESET USING DATA_5 TOGGLE - /*Register : DATA_5 @ 0XFF0A0054</p> - - Output Data - PSU_GPIO_DATA_5_DATA_5 0x80000000 - - Output Data (GPIO Bank5, EMIO) - (OFFSET, MASK, VALUE) (0XFF0A0054, 0xFFFFFFFFU ,0x80000000U) - RegMask = (GPIO_DATA_5_DATA_5_MASK | 0 ); - - RegVal = ((0x80000000U << GPIO_DATA_5_DATA_5_SHIFT - | 0 ) & RegMask); */ - PSU_Mask_Write (GPIO_DATA_5_OFFSET ,0xFFFFFFFFU ,0x80000000U); - /*############################################################################################################################ */ - - - return 1; -} - -unsigned long psu_ddr_phybringup_data() { - - - unsigned int regval = 0; - int dpll_divisor; - dpll_divisor = (Xil_In32(0xFD1A0080U) & 0x00003F00U) >> 0x00000008U; - prog_reg (0xFD1A0080U, 0x00003F00U, 0x00000008U, 0x00000005U); - prog_reg (0xFD080028U, 0x00000001U, 0x00000000U, 0x00000001U); - Xil_Out32(0xFD080004U, 0x00040003U); - while ((Xil_In32(0xFD080030U) & 0x00000001U) != 0x00000001U); - prog_reg (0xFD080684U, 0x06000000U, 0x00000019U, 0x00000001U); - prog_reg (0xFD0806A4U, 0x06000000U, 0x00000019U, 0x00000001U); - prog_reg (0xFD0806C4U, 0x06000000U, 0x00000019U, 0x00000001U); - prog_reg (0xFD0806E4U, 0x06000000U, 0x00000019U, 0x00000001U); - prog_reg (0xFD1A0080, 0x3F00, 0x8, dpll_divisor); - Xil_Out32(0xFD080004U, 0x40040071U); - while ((Xil_In32(0xFD080030U) & 0x00000001U) != 0x00000001U); - Xil_Out32(0xFD080004U, 0x40040001U); - while ((Xil_In32(0xFD080030U) & 0x00000001U) != 0x00000001U); - // PHY BRINGUP SEQ - while ((Xil_In32(0xFD080030U) & 0x0000000FU) != 0x0000000FU); - prog_reg (0xFD080004U, 0x00000001U, 0x00000000U, 0x00000001U); - //poll for PHY initialization to complete - while ((Xil_In32(0xFD080030U) & 0x000000FFU) != 0x0000001FU); - - Xil_Out32(0xFD0701B0U, 0x00000001U); - Xil_Out32(0xFD070320U, 0x00000001U); - while ((Xil_In32(0xFD070004U) & 0x0000000FU) != 0x00000001U); - prog_reg (0xFD080014U, 0x00000040U, 0x00000006U, 0x00000001U); - Xil_Out32(0xFD080004, 0x0004FE01); //PUB_PIR - regval = Xil_In32(0xFD080030); //PUB_PGSR0 - while(regval != 0x80000FFF){ - regval = Xil_In32(0xFD080030); //PUB_PGSR0 - } - - - // Run Vref training in static read mode - Xil_Out32(0xFD080200U, 0x100091C7U); - Xil_Out32(0xFD080018U, 0x00F01EF2U); - Xil_Out32(0xFD08001CU, 0x55AA5498U); - Xil_Out32(0xFD08142CU, 0x00041830U); - Xil_Out32(0xFD08146CU, 0x00041830U); - Xil_Out32(0xFD0814ACU, 0x00041830U); - Xil_Out32(0xFD0814ECU, 0x00041830U); - Xil_Out32(0xFD08152CU, 0x00041830U); - - - Xil_Out32(0xFD080004, 0x00060001); //PUB_PIR - regval = Xil_In32(0xFD080030); //PUB_PGSR0 - while((regval & 0x80004001) != 0x80004001){ - regval = Xil_In32(0xFD080030); //PUB_PGSR0 - } - - // Vref training is complete, disabling static read mode - Xil_Out32(0xFD080200U, 0x800091C7U); - Xil_Out32(0xFD080018U, 0x00F12302U); - Xil_Out32(0xFD08001CU, 0x55AA5480U); - Xil_Out32(0xFD08142CU, 0x00041800U); - Xil_Out32(0xFD08146CU, 0x00041800U); - Xil_Out32(0xFD0814ACU, 0x00041800U); - Xil_Out32(0xFD0814ECU, 0x00041800U); - Xil_Out32(0xFD08152CU, 0x00041800U); - - - Xil_Out32(0xFD080004, 0x0000C001); //PUB_PIR - regval = Xil_In32(0xFD080030); //PUB_PGSR0 - while((regval & 0x80000C01) != 0x80000C01){ - regval = Xil_In32(0xFD080030); //PUB_PGSR0 - } - - Xil_Out32(0xFD070180U, 0x01000040U); - Xil_Out32(0xFD070060U, 0x00000000U); - prog_reg (0xFD080014U, 0x00000040U, 0x00000006U, 0x00000000U); - -return 1; -} - -/** - * CRL_APB Base Address - */ -#define CRL_APB_BASEADDR 0XFF5E0000U -#define CRL_APB_RST_LPD_IOU0 ( ( CRL_APB_BASEADDR ) + 0X00000230U ) -#define CRL_APB_RST_LPD_IOU1 ( ( CRL_APB_BASEADDR ) + 0X00000234U ) -#define CRL_APB_RST_LPD_IOU2 ( ( CRL_APB_BASEADDR ) + 0X00000238U ) -#define CRL_APB_RST_LPD_TOP ( ( CRL_APB_BASEADDR ) + 0X0000023CU ) -#define CRL_APB_IOU_SWITCH_CTRL ( ( CRL_APB_BASEADDR ) + 0X0000009CU ) - -/** - * CRF_APB Base Address - */ -#define CRF_APB_BASEADDR 0XFD1A0000U - -#define CRF_APB_RST_FPD_TOP ( ( CRF_APB_BASEADDR ) + 0X00000100U ) -#define CRF_APB_GPU_REF_CTRL ( ( CRF_APB_BASEADDR ) + 0X00000084U ) -#define CRF_APB_RST_DDR_SS ( ( CRF_APB_BASEADDR ) + 0X00000108U ) -#define PSU_MASK_POLL_TIME 1100000 - - -int mask_pollOnValue(u32 add , u32 mask, u32 value ) { - volatile u32 *addr = (volatile u32*)(unsigned long) add; - int i = 0; - while ((*addr & mask)!= value) { - if (i == PSU_MASK_POLL_TIME) { - return 0; - } - i++; - } - return 1; - //xil_printf("MaskPoll : 0x%x --> 0x%x \n \r" , add, *addr); -} - -int mask_poll(u32 add , u32 mask) { - volatile u32 *addr = (volatile u32*)(unsigned long) add; - int i = 0; - while (!(*addr & mask)) { - if (i == PSU_MASK_POLL_TIME) { - return 0; - } - i++; - } - return 1; - //xil_printf("MaskPoll : 0x%x --> 0x%x \n \r" , add, *addr); -} - -void mask_delay(u32 delay) { - usleep (delay); -} - -u32 mask_read(u32 add , u32 mask ) { - volatile u32 *addr = (volatile u32*)(unsigned long) add; - u32 val = (*addr & mask); - //xil_printf("MaskRead : 0x%x --> 0x%x \n \r" , add, val); - return val; -} - - -//Following SERDES programming sequences that a user need to follow to work around the known limitation with SERDES. -//These sequences should done before STEP 1 and STEP 2 as described in previous section. These programming steps are -//required for current silicon version and are likely to undergo further changes with subsequent silicon versions. - - - -int serdes_fixcal_code() { - int MaskStatus = 1; - - // L3_TM_CALIB_DIG19 - Xil_Out32(0xFD40EC4C,0x00000020); - //ICM_CFG0 - Xil_Out32(0xFD410010,0x00000001); - - //is calibration done, polling on L3_CALIB_DONE_STATUS - MaskStatus = mask_poll(0xFD40EF14, 0x2); - - if (MaskStatus == 0) - { - xil_printf("SERDES initialization timed out\n\r"); - } - - unsigned int tmp_0_1; - tmp_0_1 = mask_read(0xFD400B0C, 0x3F); - - unsigned int tmp_0_2 = tmp_0_1 & (0x7); - unsigned int tmp_0_3 = tmp_0_1 & (0x38); - //Configure ICM for de-asserting CMN_Resetn - Xil_Out32(0xFD410010,0x00000000); - Xil_Out32(0xFD410014,0x00000000); - - unsigned int tmp_0_2_mod = (tmp_0_2 <<1) | (0x1); - tmp_0_2_mod = (tmp_0_2_mod <<4); - - tmp_0_3 = tmp_0_3 >>3; - Xil_Out32(0xFD40EC4C,tmp_0_3); - - //L3_TM_CALIB_DIG18 - Xil_Out32(0xFD40EC48,tmp_0_2_mod); - return MaskStatus; - - -} - -int serdes_enb_coarse_saturation() { - //Enable PLL Coarse Code saturation Logic - Xil_Out32(0xFD402094,0x00000010); - Xil_Out32(0xFD406094,0x00000010); - Xil_Out32(0xFD40A094,0x00000010); - Xil_Out32(0xFD40E094,0x00000010); - return 1; -} - -int init_serdes() { - int status = 1; - status &= psu_resetin_init_data(); - - status &= serdes_fixcal_code(); - status &= serdes_enb_coarse_saturation(); - - status &= psu_serdes_init_data(); - status &= psu_resetout_init_data(); - - return status; -} - - - - - - -void init_peripheral() -{ - unsigned int RegValue; - - /* Turn on IOU Clock */ - //Xil_Out32( CRL_APB_IOU_SWITCH_CTRL, 0x01001500); - - /* Release all resets in the IOU */ - Xil_Out32( CRL_APB_RST_LPD_IOU0, 0x00000000); - Xil_Out32( CRL_APB_RST_LPD_IOU1, 0x00000000); - Xil_Out32( CRL_APB_RST_LPD_IOU2, 0x00000000); - - /* Activate GPU clocks */ - //Xil_Out32(CRF_APB_GPU_REF_CTRL, 0x07001500); - - /* Take LPD out of reset except R5 */ - RegValue = Xil_In32(CRL_APB_RST_LPD_TOP); - RegValue &= 0x7; - Xil_Out32( CRL_APB_RST_LPD_TOP, RegValue); - - /* Take most of FPD out of reset */ - Xil_Out32( CRF_APB_RST_FPD_TOP, 0x00000000); - - /* Making DPDMA as secure */ - unsigned int tmp_regval; - tmp_regval = Xil_In32(0xFD690040); - tmp_regval &= ~0x00000001; - Xil_Out32(0xFD690040, tmp_regval); - - /* Making PCIe as secure */ - tmp_regval = Xil_In32(0xFD690030); - tmp_regval &= ~0x00000001; - Xil_Out32(0xFD690030, tmp_regval); -} - -int psu_init_xppu_aper_ram() { - unsigned long APER_OFFSET = 0xFF981000; - int i = 0; - for (; i <= 400; i++) { - PSU_Mask_Write (APER_OFFSET ,0xF80FFFFFU ,0x08080000U); - APER_OFFSET = APER_OFFSET + 0x4; - } - - return 0; -} - -int psu_lpd_protection() { - psu_init_xppu_aper_ram(); - psu_lpd_xppu_data(); - return 0; -} - -int psu_ddr_protection() { - psu_ddr_xmpu0_data(); - psu_ddr_xmpu1_data(); - psu_ddr_xmpu2_data(); - psu_ddr_xmpu3_data(); - psu_ddr_xmpu4_data(); - psu_ddr_xmpu5_data(); - return 0; -} -int psu_ocm_protection() { - psu_ocm_xmpu_data(); - return 0; -} - -int psu_fpd_protection() { - psu_fpd_xmpu_data(); - return 0; -} - -int psu_protection_lock() { - psu_protection_lock_data(); - return 0; -} - -int psu_protection() { - psu_ddr_protection(); - psu_ocm_protection(); - psu_fpd_protection(); - psu_lpd_protection(); - return 0; -} - - - -int -psu_init() -{ - int status = 1; - status &= psu_mio_init_data (); - status &= psu_pll_init_data (); - status &= psu_clock_init_data (); - - status &= psu_ddr_init_data (); - status &= psu_ddr_phybringup_data (); - status &= psu_peripherals_init_data (); - - status &= init_serdes(); - init_peripheral (); - - status &= psu_peripherals_powerdwn_data (); - - if (status == 0) { - return 1; - } - return 0; -} diff --git a/board/xilinx/zynqmp/zynqmp-zcu102/psu_init_gpl.h b/board/xilinx/zynqmp/zynqmp-zcu102/psu_init_gpl.h deleted file mode 100644 index 68e3562313..0000000000 --- a/board/xilinx/zynqmp/zynqmp-zcu102/psu_init_gpl.h +++ /dev/null @@ -1,30391 +0,0 @@ -/****************************************************************************** -* -* Copyright (C) 2015 Xilinx, Inc. All rights reserved. -* -* This program is free software; you can redistribute it and/or modify -* it under the terms of the GNU General Public License as published by -* the Free Software Foundation; either version 2 of the License, or -* (at your option) any later version. -* -* This program is distributed in the hope that it will be useful, -* but WITHOUT ANY WARRANTY; without even the implied warranty of -* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -* GNU General Public License for more details. -* -* You should have received a copy of the GNU General Public License along -* with this program; if not, see <http://www.gnu.org/licenses/> -* -* -******************************************************************************/ -/****************************************************************************/ -/** -* -* @file psu_init_gpl.h -* -* This file is automatically generated -* -*****************************************************************************/ - - -#undef CRL_APB_RPLL_CFG_OFFSET -#define CRL_APB_RPLL_CFG_OFFSET 0XFF5E0034 -#undef CRL_APB_RPLL_CTRL_OFFSET -#define CRL_APB_RPLL_CTRL_OFFSET 0XFF5E0030 -#undef CRL_APB_RPLL_CTRL_OFFSET -#define CRL_APB_RPLL_CTRL_OFFSET 0XFF5E0030 -#undef CRL_APB_RPLL_CTRL_OFFSET -#define CRL_APB_RPLL_CTRL_OFFSET 0XFF5E0030 -#undef CRL_APB_RPLL_CTRL_OFFSET -#define CRL_APB_RPLL_CTRL_OFFSET 0XFF5E0030 -#undef CRL_APB_RPLL_CTRL_OFFSET -#define CRL_APB_RPLL_CTRL_OFFSET 0XFF5E0030 -#undef CRL_APB_RPLL_TO_FPD_CTRL_OFFSET -#define CRL_APB_RPLL_TO_FPD_CTRL_OFFSET 0XFF5E0048 -#undef CRL_APB_RPLL_FRAC_CFG_OFFSET -#define CRL_APB_RPLL_FRAC_CFG_OFFSET 0XFF5E0038 -#undef CRL_APB_IOPLL_CFG_OFFSET -#define CRL_APB_IOPLL_CFG_OFFSET 0XFF5E0024 -#undef CRL_APB_IOPLL_CTRL_OFFSET -#define CRL_APB_IOPLL_CTRL_OFFSET 0XFF5E0020 -#undef CRL_APB_IOPLL_CTRL_OFFSET -#define CRL_APB_IOPLL_CTRL_OFFSET 0XFF5E0020 -#undef CRL_APB_IOPLL_CTRL_OFFSET -#define CRL_APB_IOPLL_CTRL_OFFSET 0XFF5E0020 -#undef CRL_APB_IOPLL_CTRL_OFFSET -#define CRL_APB_IOPLL_CTRL_OFFSET 0XFF5E0020 -#undef CRL_APB_IOPLL_CTRL_OFFSET -#define CRL_APB_IOPLL_CTRL_OFFSET 0XFF5E0020 -#undef CRL_APB_IOPLL_TO_FPD_CTRL_OFFSET -#define CRL_APB_IOPLL_TO_FPD_CTRL_OFFSET 0XFF5E0044 -#undef CRL_APB_IOPLL_FRAC_CFG_OFFSET -#define CRL_APB_IOPLL_FRAC_CFG_OFFSET 0XFF5E0028 -#undef CRF_APB_APLL_CFG_OFFSET -#define CRF_APB_APLL_CFG_OFFSET 0XFD1A0024 -#undef CRF_APB_APLL_CTRL_OFFSET -#define CRF_APB_APLL_CTRL_OFFSET 0XFD1A0020 -#undef CRF_APB_APLL_CTRL_OFFSET -#define CRF_APB_APLL_CTRL_OFFSET 0XFD1A0020 -#undef CRF_APB_APLL_CTRL_OFFSET -#define CRF_APB_APLL_CTRL_OFFSET 0XFD1A0020 -#undef CRF_APB_APLL_CTRL_OFFSET -#define CRF_APB_APLL_CTRL_OFFSET 0XFD1A0020 -#undef CRF_APB_APLL_CTRL_OFFSET -#define CRF_APB_APLL_CTRL_OFFSET 0XFD1A0020 -#undef CRF_APB_APLL_TO_LPD_CTRL_OFFSET -#define CRF_APB_APLL_TO_LPD_CTRL_OFFSET 0XFD1A0048 -#undef CRF_APB_APLL_FRAC_CFG_OFFSET -#define CRF_APB_APLL_FRAC_CFG_OFFSET 0XFD1A0028 -#undef CRF_APB_DPLL_CFG_OFFSET -#define CRF_APB_DPLL_CFG_OFFSET 0XFD1A0030 -#undef CRF_APB_DPLL_CTRL_OFFSET -#define CRF_APB_DPLL_CTRL_OFFSET 0XFD1A002C -#undef CRF_APB_DPLL_CTRL_OFFSET -#define CRF_APB_DPLL_CTRL_OFFSET 0XFD1A002C -#undef CRF_APB_DPLL_CTRL_OFFSET -#define CRF_APB_DPLL_CTRL_OFFSET 0XFD1A002C -#undef CRF_APB_DPLL_CTRL_OFFSET -#define CRF_APB_DPLL_CTRL_OFFSET 0XFD1A002C -#undef CRF_APB_DPLL_CTRL_OFFSET -#define CRF_APB_DPLL_CTRL_OFFSET 0XFD1A002C -#undef CRF_APB_DPLL_TO_LPD_CTRL_OFFSET -#define CRF_APB_DPLL_TO_LPD_CTRL_OFFSET 0XFD1A004C -#undef CRF_APB_DPLL_FRAC_CFG_OFFSET -#define CRF_APB_DPLL_FRAC_CFG_OFFSET 0XFD1A0034 -#undef CRF_APB_VPLL_CFG_OFFSET -#define CRF_APB_VPLL_CFG_OFFSET 0XFD1A003C -#undef CRF_APB_VPLL_CTRL_OFFSET -#define CRF_APB_VPLL_CTRL_OFFSET 0XFD1A0038 -#undef CRF_APB_VPLL_CTRL_OFFSET -#define CRF_APB_VPLL_CTRL_OFFSET 0XFD1A0038 -#undef CRF_APB_VPLL_CTRL_OFFSET -#define CRF_APB_VPLL_CTRL_OFFSET 0XFD1A0038 -#undef CRF_APB_VPLL_CTRL_OFFSET -#define CRF_APB_VPLL_CTRL_OFFSET 0XFD1A0038 -#undef CRF_APB_VPLL_CTRL_OFFSET -#define CRF_APB_VPLL_CTRL_OFFSET 0XFD1A0038 -#undef CRF_APB_VPLL_TO_LPD_CTRL_OFFSET -#define CRF_APB_VPLL_TO_LPD_CTRL_OFFSET 0XFD1A0050 -#undef CRF_APB_VPLL_FRAC_CFG_OFFSET -#define CRF_APB_VPLL_FRAC_CFG_OFFSET 0XFD1A0040 - -/*PLL loop filter resistor control*/ -#undef CRL_APB_RPLL_CFG_RES_DEFVAL -#undef CRL_APB_RPLL_CFG_RES_SHIFT -#undef CRL_APB_RPLL_CFG_RES_MASK -#define CRL_APB_RPLL_CFG_RES_DEFVAL 0x00000000 -#define CRL_APB_RPLL_CFG_RES_SHIFT 0 -#define CRL_APB_RPLL_CFG_RES_MASK 0x0000000FU - -/*PLL charge pump control*/ -#undef CRL_APB_RPLL_CFG_CP_DEFVAL -#undef CRL_APB_RPLL_CFG_CP_SHIFT -#undef CRL_APB_RPLL_CFG_CP_MASK -#define CRL_APB_RPLL_CFG_CP_DEFVAL 0x00000000 -#define CRL_APB_RPLL_CFG_CP_SHIFT 5 -#define CRL_APB_RPLL_CFG_CP_MASK 0x000001E0U - -/*PLL loop filter high frequency capacitor control*/ -#undef CRL_APB_RPLL_CFG_LFHF_DEFVAL -#undef CRL_APB_RPLL_CFG_LFHF_SHIFT -#undef CRL_APB_RPLL_CFG_LFHF_MASK -#define CRL_APB_RPLL_CFG_LFHF_DEFVAL 0x00000000 -#define CRL_APB_RPLL_CFG_LFHF_SHIFT 10 -#define CRL_APB_RPLL_CFG_LFHF_MASK 0x00000C00U - -/*Lock circuit counter setting*/ -#undef CRL_APB_RPLL_CFG_LOCK_CNT_DEFVAL -#undef CRL_APB_RPLL_CFG_LOCK_CNT_SHIFT -#undef CRL_APB_RPLL_CFG_LOCK_CNT_MASK -#define CRL_APB_RPLL_CFG_LOCK_CNT_DEFVAL 0x00000000 -#define CRL_APB_RPLL_CFG_LOCK_CNT_SHIFT 13 -#define CRL_APB_RPLL_CFG_LOCK_CNT_MASK 0x007FE000U - -/*Lock circuit configuration settings for lock windowsize*/ -#undef CRL_APB_RPLL_CFG_LOCK_DLY_DEFVAL -#undef CRL_APB_RPLL_CFG_LOCK_DLY_SHIFT -#undef CRL_APB_RPLL_CFG_LOCK_DLY_MASK -#define CRL_APB_RPLL_CFG_LOCK_DLY_DEFVAL 0x00000000 -#define CRL_APB_RPLL_CFG_LOCK_DLY_SHIFT 25 -#define CRL_APB_RPLL_CFG_LOCK_DLY_MASK 0xFE000000U - -/*Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_ - ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source*/ -#undef CRL_APB_RPLL_CTRL_PRE_SRC_DEFVAL -#undef CRL_APB_RPLL_CTRL_PRE_SRC_SHIFT -#undef CRL_APB_RPLL_CTRL_PRE_SRC_MASK -#define CRL_APB_RPLL_CTRL_PRE_SRC_DEFVAL 0x00012C09 -#define CRL_APB_RPLL_CTRL_PRE_SRC_SHIFT 20 -#define CRL_APB_RPLL_CTRL_PRE_SRC_MASK 0x00700000U - -/*The integer portion of the feedback divider to the PLL*/ -#undef CRL_APB_RPLL_CTRL_FBDIV_DEFVAL -#undef CRL_APB_RPLL_CTRL_FBDIV_SHIFT -#undef CRL_APB_RPLL_CTRL_FBDIV_MASK -#define CRL_APB_RPLL_CTRL_FBDIV_DEFVAL 0x00012C09 -#define CRL_APB_RPLL_CTRL_FBDIV_SHIFT 8 -#define CRL_APB_RPLL_CTRL_FBDIV_MASK 0x00007F00U - -/*This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency*/ -#undef CRL_APB_RPLL_CTRL_DIV2_DEFVAL -#undef CRL_APB_RPLL_CTRL_DIV2_SHIFT -#undef CRL_APB_RPLL_CTRL_DIV2_MASK -#define CRL_APB_RPLL_CTRL_DIV2_DEFVAL 0x00012C09 -#define CRL_APB_RPLL_CTRL_DIV2_SHIFT 16 -#define CRL_APB_RPLL_CTRL_DIV2_MASK 0x00010000U - -/*Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_RPLL_CTRL_BYPASS_DEFVAL -#undef CRL_APB_RPLL_CTRL_BYPASS_SHIFT -#undef CRL_APB_RPLL_CTRL_BYPASS_MASK -#define CRL_APB_RPLL_CTRL_BYPASS_DEFVAL 0x00012C09 -#define CRL_APB_RPLL_CTRL_BYPASS_SHIFT 3 -#define CRL_APB_RPLL_CTRL_BYPASS_MASK 0x00000008U - -/*Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.*/ -#undef CRL_APB_RPLL_CTRL_RESET_DEFVAL -#undef CRL_APB_RPLL_CTRL_RESET_SHIFT -#undef CRL_APB_RPLL_CTRL_RESET_MASK -#define CRL_APB_RPLL_CTRL_RESET_DEFVAL 0x00012C09 -#define CRL_APB_RPLL_CTRL_RESET_SHIFT 0 -#define CRL_APB_RPLL_CTRL_RESET_MASK 0x00000001U - -/*Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.*/ -#undef CRL_APB_RPLL_CTRL_RESET_DEFVAL -#undef CRL_APB_RPLL_CTRL_RESET_SHIFT -#undef CRL_APB_RPLL_CTRL_RESET_MASK -#define CRL_APB_RPLL_CTRL_RESET_DEFVAL 0x00012C09 -#define CRL_APB_RPLL_CTRL_RESET_SHIFT 0 -#define CRL_APB_RPLL_CTRL_RESET_MASK 0x00000001U - -/*RPLL is locked*/ -#undef CRL_APB_PLL_STATUS_RPLL_LOCK_DEFVAL -#undef CRL_APB_PLL_STATUS_RPLL_LOCK_SHIFT -#undef CRL_APB_PLL_STATUS_RPLL_LOCK_MASK -#define CRL_APB_PLL_STATUS_RPLL_LOCK_DEFVAL 0x00000018 -#define CRL_APB_PLL_STATUS_RPLL_LOCK_SHIFT 1 -#define CRL_APB_PLL_STATUS_RPLL_LOCK_MASK 0x00000002U -#define CRL_APB_PLL_STATUS_OFFSET 0XFF5E0040 - -/*Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_RPLL_CTRL_BYPASS_DEFVAL -#undef CRL_APB_RPLL_CTRL_BYPASS_SHIFT -#undef CRL_APB_RPLL_CTRL_BYPASS_MASK -#define CRL_APB_RPLL_CTRL_BYPASS_DEFVAL 0x00012C09 -#define CRL_APB_RPLL_CTRL_BYPASS_SHIFT 3 -#define CRL_APB_RPLL_CTRL_BYPASS_MASK 0x00000008U - -/*Divisor value for this clock.*/ -#undef CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0_MASK -#define CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0_DEFVAL 0x00000400 -#define CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_RPLL_TO_FPD_CTRL_DIVISOR0_MASK 0x00003F00U - -/*Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona - mode and uses DATA of this register for the fractional portion of the feedback divider.*/ -#undef CRL_APB_RPLL_FRAC_CFG_ENABLED_DEFVAL -#undef CRL_APB_RPLL_FRAC_CFG_ENABLED_SHIFT -#undef CRL_APB_RPLL_FRAC_CFG_ENABLED_MASK -#define CRL_APB_RPLL_FRAC_CFG_ENABLED_DEFVAL 0x00000000 -#define CRL_APB_RPLL_FRAC_CFG_ENABLED_SHIFT 31 -#define CRL_APB_RPLL_FRAC_CFG_ENABLED_MASK 0x80000000U - -/*Fractional value for the Feedback value.*/ -#undef CRL_APB_RPLL_FRAC_CFG_DATA_DEFVAL -#undef CRL_APB_RPLL_FRAC_CFG_DATA_SHIFT -#undef CRL_APB_RPLL_FRAC_CFG_DATA_MASK -#define CRL_APB_RPLL_FRAC_CFG_DATA_DEFVAL 0x00000000 -#define CRL_APB_RPLL_FRAC_CFG_DATA_SHIFT 0 -#define CRL_APB_RPLL_FRAC_CFG_DATA_MASK 0x0000FFFFU - -/*PLL loop filter resistor control*/ -#undef CRL_APB_IOPLL_CFG_RES_DEFVAL -#undef CRL_APB_IOPLL_CFG_RES_SHIFT -#undef CRL_APB_IOPLL_CFG_RES_MASK -#define CRL_APB_IOPLL_CFG_RES_DEFVAL 0x00000000 -#define CRL_APB_IOPLL_CFG_RES_SHIFT 0 -#define CRL_APB_IOPLL_CFG_RES_MASK 0x0000000FU - -/*PLL charge pump control*/ -#undef CRL_APB_IOPLL_CFG_CP_DEFVAL -#undef CRL_APB_IOPLL_CFG_CP_SHIFT -#undef CRL_APB_IOPLL_CFG_CP_MASK -#define CRL_APB_IOPLL_CFG_CP_DEFVAL 0x00000000 -#define CRL_APB_IOPLL_CFG_CP_SHIFT 5 -#define CRL_APB_IOPLL_CFG_CP_MASK 0x000001E0U - -/*PLL loop filter high frequency capacitor control*/ -#undef CRL_APB_IOPLL_CFG_LFHF_DEFVAL -#undef CRL_APB_IOPLL_CFG_LFHF_SHIFT -#undef CRL_APB_IOPLL_CFG_LFHF_MASK -#define CRL_APB_IOPLL_CFG_LFHF_DEFVAL 0x00000000 -#define CRL_APB_IOPLL_CFG_LFHF_SHIFT 10 -#define CRL_APB_IOPLL_CFG_LFHF_MASK 0x00000C00U - -/*Lock circuit counter setting*/ -#undef CRL_APB_IOPLL_CFG_LOCK_CNT_DEFVAL -#undef CRL_APB_IOPLL_CFG_LOCK_CNT_SHIFT -#undef CRL_APB_IOPLL_CFG_LOCK_CNT_MASK -#define CRL_APB_IOPLL_CFG_LOCK_CNT_DEFVAL 0x00000000 -#define CRL_APB_IOPLL_CFG_LOCK_CNT_SHIFT 13 -#define CRL_APB_IOPLL_CFG_LOCK_CNT_MASK 0x007FE000U - -/*Lock circuit configuration settings for lock windowsize*/ -#undef CRL_APB_IOPLL_CFG_LOCK_DLY_DEFVAL -#undef CRL_APB_IOPLL_CFG_LOCK_DLY_SHIFT -#undef CRL_APB_IOPLL_CFG_LOCK_DLY_MASK -#define CRL_APB_IOPLL_CFG_LOCK_DLY_DEFVAL 0x00000000 -#define CRL_APB_IOPLL_CFG_LOCK_DLY_SHIFT 25 -#define CRL_APB_IOPLL_CFG_LOCK_DLY_MASK 0xFE000000U - -/*Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_ - ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source*/ -#undef CRL_APB_IOPLL_CTRL_PRE_SRC_DEFVAL -#undef CRL_APB_IOPLL_CTRL_PRE_SRC_SHIFT -#undef CRL_APB_IOPLL_CTRL_PRE_SRC_MASK -#define CRL_APB_IOPLL_CTRL_PRE_SRC_DEFVAL 0x00012C09 -#define CRL_APB_IOPLL_CTRL_PRE_SRC_SHIFT 20 -#define CRL_APB_IOPLL_CTRL_PRE_SRC_MASK 0x00700000U - -/*The integer portion of the feedback divider to the PLL*/ -#undef CRL_APB_IOPLL_CTRL_FBDIV_DEFVAL -#undef CRL_APB_IOPLL_CTRL_FBDIV_SHIFT -#undef CRL_APB_IOPLL_CTRL_FBDIV_MASK -#define CRL_APB_IOPLL_CTRL_FBDIV_DEFVAL 0x00012C09 -#define CRL_APB_IOPLL_CTRL_FBDIV_SHIFT 8 -#define CRL_APB_IOPLL_CTRL_FBDIV_MASK 0x00007F00U - -/*This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency*/ -#undef CRL_APB_IOPLL_CTRL_DIV2_DEFVAL -#undef CRL_APB_IOPLL_CTRL_DIV2_SHIFT -#undef CRL_APB_IOPLL_CTRL_DIV2_MASK -#define CRL_APB_IOPLL_CTRL_DIV2_DEFVAL 0x00012C09 -#define CRL_APB_IOPLL_CTRL_DIV2_SHIFT 16 -#define CRL_APB_IOPLL_CTRL_DIV2_MASK 0x00010000U - -/*Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_IOPLL_CTRL_BYPASS_DEFVAL -#undef CRL_APB_IOPLL_CTRL_BYPASS_SHIFT -#undef CRL_APB_IOPLL_CTRL_BYPASS_MASK -#define CRL_APB_IOPLL_CTRL_BYPASS_DEFVAL 0x00012C09 -#define CRL_APB_IOPLL_CTRL_BYPASS_SHIFT 3 -#define CRL_APB_IOPLL_CTRL_BYPASS_MASK 0x00000008U - -/*Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.*/ -#undef CRL_APB_IOPLL_CTRL_RESET_DEFVAL -#undef CRL_APB_IOPLL_CTRL_RESET_SHIFT -#undef CRL_APB_IOPLL_CTRL_RESET_MASK -#define CRL_APB_IOPLL_CTRL_RESET_DEFVAL 0x00012C09 -#define CRL_APB_IOPLL_CTRL_RESET_SHIFT 0 -#define CRL_APB_IOPLL_CTRL_RESET_MASK 0x00000001U - -/*Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.*/ -#undef CRL_APB_IOPLL_CTRL_RESET_DEFVAL -#undef CRL_APB_IOPLL_CTRL_RESET_SHIFT -#undef CRL_APB_IOPLL_CTRL_RESET_MASK -#define CRL_APB_IOPLL_CTRL_RESET_DEFVAL 0x00012C09 -#define CRL_APB_IOPLL_CTRL_RESET_SHIFT 0 -#define CRL_APB_IOPLL_CTRL_RESET_MASK 0x00000001U - -/*IOPLL is locked*/ -#undef CRL_APB_PLL_STATUS_IOPLL_LOCK_DEFVAL -#undef CRL_APB_PLL_STATUS_IOPLL_LOCK_SHIFT -#undef CRL_APB_PLL_STATUS_IOPLL_LOCK_MASK -#define CRL_APB_PLL_STATUS_IOPLL_LOCK_DEFVAL 0x00000018 -#define CRL_APB_PLL_STATUS_IOPLL_LOCK_SHIFT 0 -#define CRL_APB_PLL_STATUS_IOPLL_LOCK_MASK 0x00000001U -#define CRL_APB_PLL_STATUS_OFFSET 0XFF5E0040 - -/*Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_IOPLL_CTRL_BYPASS_DEFVAL -#undef CRL_APB_IOPLL_CTRL_BYPASS_SHIFT -#undef CRL_APB_IOPLL_CTRL_BYPASS_MASK -#define CRL_APB_IOPLL_CTRL_BYPASS_DEFVAL 0x00012C09 -#define CRL_APB_IOPLL_CTRL_BYPASS_SHIFT 3 -#define CRL_APB_IOPLL_CTRL_BYPASS_MASK 0x00000008U - -/*Divisor value for this clock.*/ -#undef CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0_MASK -#define CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0_DEFVAL 0x00000400 -#define CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_IOPLL_TO_FPD_CTRL_DIVISOR0_MASK 0x00003F00U - -/*Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona - mode and uses DATA of this register for the fractional portion of the feedback divider.*/ -#undef CRL_APB_IOPLL_FRAC_CFG_ENABLED_DEFVAL -#undef CRL_APB_IOPLL_FRAC_CFG_ENABLED_SHIFT -#undef CRL_APB_IOPLL_FRAC_CFG_ENABLED_MASK -#define CRL_APB_IOPLL_FRAC_CFG_ENABLED_DEFVAL 0x00000000 -#define CRL_APB_IOPLL_FRAC_CFG_ENABLED_SHIFT 31 -#define CRL_APB_IOPLL_FRAC_CFG_ENABLED_MASK 0x80000000U - -/*Fractional value for the Feedback value.*/ -#undef CRL_APB_IOPLL_FRAC_CFG_DATA_DEFVAL -#undef CRL_APB_IOPLL_FRAC_CFG_DATA_SHIFT -#undef CRL_APB_IOPLL_FRAC_CFG_DATA_MASK -#define CRL_APB_IOPLL_FRAC_CFG_DATA_DEFVAL 0x00000000 -#define CRL_APB_IOPLL_FRAC_CFG_DATA_SHIFT 0 -#define CRL_APB_IOPLL_FRAC_CFG_DATA_MASK 0x0000FFFFU - -/*PLL loop filter resistor control*/ -#undef CRF_APB_APLL_CFG_RES_DEFVAL -#undef CRF_APB_APLL_CFG_RES_SHIFT -#undef CRF_APB_APLL_CFG_RES_MASK -#define CRF_APB_APLL_CFG_RES_DEFVAL 0x00000000 -#define CRF_APB_APLL_CFG_RES_SHIFT 0 -#define CRF_APB_APLL_CFG_RES_MASK 0x0000000FU - -/*PLL charge pump control*/ -#undef CRF_APB_APLL_CFG_CP_DEFVAL -#undef CRF_APB_APLL_CFG_CP_SHIFT -#undef CRF_APB_APLL_CFG_CP_MASK -#define CRF_APB_APLL_CFG_CP_DEFVAL 0x00000000 -#define CRF_APB_APLL_CFG_CP_SHIFT 5 -#define CRF_APB_APLL_CFG_CP_MASK 0x000001E0U - -/*PLL loop filter high frequency capacitor control*/ -#undef CRF_APB_APLL_CFG_LFHF_DEFVAL -#undef CRF_APB_APLL_CFG_LFHF_SHIFT -#undef CRF_APB_APLL_CFG_LFHF_MASK -#define CRF_APB_APLL_CFG_LFHF_DEFVAL 0x00000000 -#define CRF_APB_APLL_CFG_LFHF_SHIFT 10 -#define CRF_APB_APLL_CFG_LFHF_MASK 0x00000C00U - -/*Lock circuit counter setting*/ -#undef CRF_APB_APLL_CFG_LOCK_CNT_DEFVAL -#undef CRF_APB_APLL_CFG_LOCK_CNT_SHIFT -#undef CRF_APB_APLL_CFG_LOCK_CNT_MASK -#define CRF_APB_APLL_CFG_LOCK_CNT_DEFVAL 0x00000000 -#define CRF_APB_APLL_CFG_LOCK_CNT_SHIFT 13 -#define CRF_APB_APLL_CFG_LOCK_CNT_MASK 0x007FE000U - -/*Lock circuit configuration settings for lock windowsize*/ -#undef CRF_APB_APLL_CFG_LOCK_DLY_DEFVAL -#undef CRF_APB_APLL_CFG_LOCK_DLY_SHIFT -#undef CRF_APB_APLL_CFG_LOCK_DLY_MASK -#define CRF_APB_APLL_CFG_LOCK_DLY_DEFVAL 0x00000000 -#define CRF_APB_APLL_CFG_LOCK_DLY_SHIFT 25 -#define CRF_APB_APLL_CFG_LOCK_DLY_MASK 0xFE000000U - -/*Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_ - ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source*/ -#undef CRF_APB_APLL_CTRL_PRE_SRC_DEFVAL -#undef CRF_APB_APLL_CTRL_PRE_SRC_SHIFT -#undef CRF_APB_APLL_CTRL_PRE_SRC_MASK -#define CRF_APB_APLL_CTRL_PRE_SRC_DEFVAL 0x00012C09 -#define CRF_APB_APLL_CTRL_PRE_SRC_SHIFT 20 -#define CRF_APB_APLL_CTRL_PRE_SRC_MASK 0x00700000U - -/*The integer portion of the feedback divider to the PLL*/ -#undef CRF_APB_APLL_CTRL_FBDIV_DEFVAL -#undef CRF_APB_APLL_CTRL_FBDIV_SHIFT -#undef CRF_APB_APLL_CTRL_FBDIV_MASK -#define CRF_APB_APLL_CTRL_FBDIV_DEFVAL 0x00012C09 -#define CRF_APB_APLL_CTRL_FBDIV_SHIFT 8 -#define CRF_APB_APLL_CTRL_FBDIV_MASK 0x00007F00U - -/*This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency*/ -#undef CRF_APB_APLL_CTRL_DIV2_DEFVAL -#undef CRF_APB_APLL_CTRL_DIV2_SHIFT -#undef CRF_APB_APLL_CTRL_DIV2_MASK -#define CRF_APB_APLL_CTRL_DIV2_DEFVAL 0x00012C09 -#define CRF_APB_APLL_CTRL_DIV2_SHIFT 16 -#define CRF_APB_APLL_CTRL_DIV2_MASK 0x00010000U - -/*Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_APLL_CTRL_BYPASS_DEFVAL -#undef CRF_APB_APLL_CTRL_BYPASS_SHIFT -#undef CRF_APB_APLL_CTRL_BYPASS_MASK -#define CRF_APB_APLL_CTRL_BYPASS_DEFVAL 0x00012C09 -#define CRF_APB_APLL_CTRL_BYPASS_SHIFT 3 -#define CRF_APB_APLL_CTRL_BYPASS_MASK 0x00000008U - -/*Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.*/ -#undef CRF_APB_APLL_CTRL_RESET_DEFVAL -#undef CRF_APB_APLL_CTRL_RESET_SHIFT -#undef CRF_APB_APLL_CTRL_RESET_MASK -#define CRF_APB_APLL_CTRL_RESET_DEFVAL 0x00012C09 -#define CRF_APB_APLL_CTRL_RESET_SHIFT 0 -#define CRF_APB_APLL_CTRL_RESET_MASK 0x00000001U - -/*Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.*/ -#undef CRF_APB_APLL_CTRL_RESET_DEFVAL -#undef CRF_APB_APLL_CTRL_RESET_SHIFT -#undef CRF_APB_APLL_CTRL_RESET_MASK -#define CRF_APB_APLL_CTRL_RESET_DEFVAL 0x00012C09 -#define CRF_APB_APLL_CTRL_RESET_SHIFT 0 -#define CRF_APB_APLL_CTRL_RESET_MASK 0x00000001U - -/*APLL is locked*/ -#undef CRF_APB_PLL_STATUS_APLL_LOCK_DEFVAL -#undef CRF_APB_PLL_STATUS_APLL_LOCK_SHIFT -#undef CRF_APB_PLL_STATUS_APLL_LOCK_MASK -#define CRF_APB_PLL_STATUS_APLL_LOCK_DEFVAL 0x00000038 -#define CRF_APB_PLL_STATUS_APLL_LOCK_SHIFT 0 -#define CRF_APB_PLL_STATUS_APLL_LOCK_MASK 0x00000001U -#define CRF_APB_PLL_STATUS_OFFSET 0XFD1A0044 - -/*Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_APLL_CTRL_BYPASS_DEFVAL -#undef CRF_APB_APLL_CTRL_BYPASS_SHIFT -#undef CRF_APB_APLL_CTRL_BYPASS_MASK -#define CRF_APB_APLL_CTRL_BYPASS_DEFVAL 0x00012C09 -#define CRF_APB_APLL_CTRL_BYPASS_SHIFT 3 -#define CRF_APB_APLL_CTRL_BYPASS_MASK 0x00000008U - -/*Divisor value for this clock.*/ -#undef CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0_MASK -#define CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0_DEFVAL 0x00000400 -#define CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_APLL_TO_LPD_CTRL_DIVISOR0_MASK 0x00003F00U - -/*Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona - mode and uses DATA of this register for the fractional portion of the feedback divider.*/ -#undef CRF_APB_APLL_FRAC_CFG_ENABLED_DEFVAL -#undef CRF_APB_APLL_FRAC_CFG_ENABLED_SHIFT -#undef CRF_APB_APLL_FRAC_CFG_ENABLED_MASK -#define CRF_APB_APLL_FRAC_CFG_ENABLED_DEFVAL 0x00000000 -#define CRF_APB_APLL_FRAC_CFG_ENABLED_SHIFT 31 -#define CRF_APB_APLL_FRAC_CFG_ENABLED_MASK 0x80000000U - -/*Fractional value for the Feedback value.*/ -#undef CRF_APB_APLL_FRAC_CFG_DATA_DEFVAL -#undef CRF_APB_APLL_FRAC_CFG_DATA_SHIFT -#undef CRF_APB_APLL_FRAC_CFG_DATA_MASK -#define CRF_APB_APLL_FRAC_CFG_DATA_DEFVAL 0x00000000 -#define CRF_APB_APLL_FRAC_CFG_DATA_SHIFT 0 -#define CRF_APB_APLL_FRAC_CFG_DATA_MASK 0x0000FFFFU - -/*PLL loop filter resistor control*/ -#undef CRF_APB_DPLL_CFG_RES_DEFVAL -#undef CRF_APB_DPLL_CFG_RES_SHIFT -#undef CRF_APB_DPLL_CFG_RES_MASK -#define CRF_APB_DPLL_CFG_RES_DEFVAL 0x00000000 -#define CRF_APB_DPLL_CFG_RES_SHIFT 0 -#define CRF_APB_DPLL_CFG_RES_MASK 0x0000000FU - -/*PLL charge pump control*/ -#undef CRF_APB_DPLL_CFG_CP_DEFVAL -#undef CRF_APB_DPLL_CFG_CP_SHIFT -#undef CRF_APB_DPLL_CFG_CP_MASK -#define CRF_APB_DPLL_CFG_CP_DEFVAL 0x00000000 -#define CRF_APB_DPLL_CFG_CP_SHIFT 5 -#define CRF_APB_DPLL_CFG_CP_MASK 0x000001E0U - -/*PLL loop filter high frequency capacitor control*/ -#undef CRF_APB_DPLL_CFG_LFHF_DEFVAL -#undef CRF_APB_DPLL_CFG_LFHF_SHIFT -#undef CRF_APB_DPLL_CFG_LFHF_MASK -#define CRF_APB_DPLL_CFG_LFHF_DEFVAL 0x00000000 -#define CRF_APB_DPLL_CFG_LFHF_SHIFT 10 -#define CRF_APB_DPLL_CFG_LFHF_MASK 0x00000C00U - -/*Lock circuit counter setting*/ -#undef CRF_APB_DPLL_CFG_LOCK_CNT_DEFVAL -#undef CRF_APB_DPLL_CFG_LOCK_CNT_SHIFT -#undef CRF_APB_DPLL_CFG_LOCK_CNT_MASK -#define CRF_APB_DPLL_CFG_LOCK_CNT_DEFVAL 0x00000000 -#define CRF_APB_DPLL_CFG_LOCK_CNT_SHIFT 13 -#define CRF_APB_DPLL_CFG_LOCK_CNT_MASK 0x007FE000U - -/*Lock circuit configuration settings for lock windowsize*/ -#undef CRF_APB_DPLL_CFG_LOCK_DLY_DEFVAL -#undef CRF_APB_DPLL_CFG_LOCK_DLY_SHIFT -#undef CRF_APB_DPLL_CFG_LOCK_DLY_MASK -#define CRF_APB_DPLL_CFG_LOCK_DLY_DEFVAL 0x00000000 -#define CRF_APB_DPLL_CFG_LOCK_DLY_SHIFT 25 -#define CRF_APB_DPLL_CFG_LOCK_DLY_MASK 0xFE000000U - -/*Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_ - ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source*/ -#undef CRF_APB_DPLL_CTRL_PRE_SRC_DEFVAL -#undef CRF_APB_DPLL_CTRL_PRE_SRC_SHIFT -#undef CRF_APB_DPLL_CTRL_PRE_SRC_MASK -#define CRF_APB_DPLL_CTRL_PRE_SRC_DEFVAL 0x00002C09 -#define CRF_APB_DPLL_CTRL_PRE_SRC_SHIFT 20 -#define CRF_APB_DPLL_CTRL_PRE_SRC_MASK 0x00700000U - -/*The integer portion of the feedback divider to the PLL*/ -#undef CRF_APB_DPLL_CTRL_FBDIV_DEFVAL -#undef CRF_APB_DPLL_CTRL_FBDIV_SHIFT -#undef CRF_APB_DPLL_CTRL_FBDIV_MASK -#define CRF_APB_DPLL_CTRL_FBDIV_DEFVAL 0x00002C09 -#define CRF_APB_DPLL_CTRL_FBDIV_SHIFT 8 -#define CRF_APB_DPLL_CTRL_FBDIV_MASK 0x00007F00U - -/*This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency*/ -#undef CRF_APB_DPLL_CTRL_DIV2_DEFVAL -#undef CRF_APB_DPLL_CTRL_DIV2_SHIFT -#undef CRF_APB_DPLL_CTRL_DIV2_MASK -#define CRF_APB_DPLL_CTRL_DIV2_DEFVAL 0x00002C09 -#define CRF_APB_DPLL_CTRL_DIV2_SHIFT 16 -#define CRF_APB_DPLL_CTRL_DIV2_MASK 0x00010000U - -/*Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_DPLL_CTRL_BYPASS_DEFVAL -#undef CRF_APB_DPLL_CTRL_BYPASS_SHIFT -#undef CRF_APB_DPLL_CTRL_BYPASS_MASK -#define CRF_APB_DPLL_CTRL_BYPASS_DEFVAL 0x00002C09 -#define CRF_APB_DPLL_CTRL_BYPASS_SHIFT 3 -#define CRF_APB_DPLL_CTRL_BYPASS_MASK 0x00000008U - -/*Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.*/ -#undef CRF_APB_DPLL_CTRL_RESET_DEFVAL -#undef CRF_APB_DPLL_CTRL_RESET_SHIFT -#undef CRF_APB_DPLL_CTRL_RESET_MASK -#define CRF_APB_DPLL_CTRL_RESET_DEFVAL 0x00002C09 -#define CRF_APB_DPLL_CTRL_RESET_SHIFT 0 -#define CRF_APB_DPLL_CTRL_RESET_MASK 0x00000001U - -/*Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.*/ -#undef CRF_APB_DPLL_CTRL_RESET_DEFVAL -#undef CRF_APB_DPLL_CTRL_RESET_SHIFT -#undef CRF_APB_DPLL_CTRL_RESET_MASK -#define CRF_APB_DPLL_CTRL_RESET_DEFVAL 0x00002C09 -#define CRF_APB_DPLL_CTRL_RESET_SHIFT 0 -#define CRF_APB_DPLL_CTRL_RESET_MASK 0x00000001U - -/*DPLL is locked*/ -#undef CRF_APB_PLL_STATUS_DPLL_LOCK_DEFVAL -#undef CRF_APB_PLL_STATUS_DPLL_LOCK_SHIFT -#undef CRF_APB_PLL_STATUS_DPLL_LOCK_MASK -#define CRF_APB_PLL_STATUS_DPLL_LOCK_DEFVAL 0x00000038 -#define CRF_APB_PLL_STATUS_DPLL_LOCK_SHIFT 1 -#define CRF_APB_PLL_STATUS_DPLL_LOCK_MASK 0x00000002U -#define CRF_APB_PLL_STATUS_OFFSET 0XFD1A0044 - -/*Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_DPLL_CTRL_BYPASS_DEFVAL -#undef CRF_APB_DPLL_CTRL_BYPASS_SHIFT -#undef CRF_APB_DPLL_CTRL_BYPASS_MASK -#define CRF_APB_DPLL_CTRL_BYPASS_DEFVAL 0x00002C09 -#define CRF_APB_DPLL_CTRL_BYPASS_SHIFT 3 -#define CRF_APB_DPLL_CTRL_BYPASS_MASK 0x00000008U - -/*Divisor value for this clock.*/ -#undef CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0_MASK -#define CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0_DEFVAL 0x00000400 -#define CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_DPLL_TO_LPD_CTRL_DIVISOR0_MASK 0x00003F00U - -/*Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona - mode and uses DATA of this register for the fractional portion of the feedback divider.*/ -#undef CRF_APB_DPLL_FRAC_CFG_ENABLED_DEFVAL -#undef CRF_APB_DPLL_FRAC_CFG_ENABLED_SHIFT -#undef CRF_APB_DPLL_FRAC_CFG_ENABLED_MASK -#define CRF_APB_DPLL_FRAC_CFG_ENABLED_DEFVAL 0x00000000 -#define CRF_APB_DPLL_FRAC_CFG_ENABLED_SHIFT 31 -#define CRF_APB_DPLL_FRAC_CFG_ENABLED_MASK 0x80000000U - -/*Fractional value for the Feedback value.*/ -#undef CRF_APB_DPLL_FRAC_CFG_DATA_DEFVAL -#undef CRF_APB_DPLL_FRAC_CFG_DATA_SHIFT -#undef CRF_APB_DPLL_FRAC_CFG_DATA_MASK -#define CRF_APB_DPLL_FRAC_CFG_DATA_DEFVAL 0x00000000 -#define CRF_APB_DPLL_FRAC_CFG_DATA_SHIFT 0 -#define CRF_APB_DPLL_FRAC_CFG_DATA_MASK 0x0000FFFFU - -/*PLL loop filter resistor control*/ -#undef CRF_APB_VPLL_CFG_RES_DEFVAL -#undef CRF_APB_VPLL_CFG_RES_SHIFT -#undef CRF_APB_VPLL_CFG_RES_MASK -#define CRF_APB_VPLL_CFG_RES_DEFVAL 0x00000000 -#define CRF_APB_VPLL_CFG_RES_SHIFT 0 -#define CRF_APB_VPLL_CFG_RES_MASK 0x0000000FU - -/*PLL charge pump control*/ -#undef CRF_APB_VPLL_CFG_CP_DEFVAL -#undef CRF_APB_VPLL_CFG_CP_SHIFT -#undef CRF_APB_VPLL_CFG_CP_MASK -#define CRF_APB_VPLL_CFG_CP_DEFVAL 0x00000000 -#define CRF_APB_VPLL_CFG_CP_SHIFT 5 -#define CRF_APB_VPLL_CFG_CP_MASK 0x000001E0U - -/*PLL loop filter high frequency capacitor control*/ -#undef CRF_APB_VPLL_CFG_LFHF_DEFVAL -#undef CRF_APB_VPLL_CFG_LFHF_SHIFT -#undef CRF_APB_VPLL_CFG_LFHF_MASK -#define CRF_APB_VPLL_CFG_LFHF_DEFVAL 0x00000000 -#define CRF_APB_VPLL_CFG_LFHF_SHIFT 10 -#define CRF_APB_VPLL_CFG_LFHF_MASK 0x00000C00U - -/*Lock circuit counter setting*/ -#undef CRF_APB_VPLL_CFG_LOCK_CNT_DEFVAL -#undef CRF_APB_VPLL_CFG_LOCK_CNT_SHIFT -#undef CRF_APB_VPLL_CFG_LOCK_CNT_MASK -#define CRF_APB_VPLL_CFG_LOCK_CNT_DEFVAL 0x00000000 -#define CRF_APB_VPLL_CFG_LOCK_CNT_SHIFT 13 -#define CRF_APB_VPLL_CFG_LOCK_CNT_MASK 0x007FE000U - -/*Lock circuit configuration settings for lock windowsize*/ -#undef CRF_APB_VPLL_CFG_LOCK_DLY_DEFVAL -#undef CRF_APB_VPLL_CFG_LOCK_DLY_SHIFT -#undef CRF_APB_VPLL_CFG_LOCK_DLY_MASK -#define CRF_APB_VPLL_CFG_LOCK_DLY_DEFVAL 0x00000000 -#define CRF_APB_VPLL_CFG_LOCK_DLY_SHIFT 25 -#define CRF_APB_VPLL_CFG_LOCK_DLY_MASK 0xFE000000U - -/*Mux select for determining which clock feeds this PLL. 0XX pss_ref_clk is the source 100 video clk is the source 101 pss_alt_ - ef_clk is the source 110 aux_refclk[X] is the source 111 gt_crx_ref_clk is the source*/ -#undef CRF_APB_VPLL_CTRL_PRE_SRC_DEFVAL -#undef CRF_APB_VPLL_CTRL_PRE_SRC_SHIFT -#undef CRF_APB_VPLL_CTRL_PRE_SRC_MASK -#define CRF_APB_VPLL_CTRL_PRE_SRC_DEFVAL 0x00012809 -#define CRF_APB_VPLL_CTRL_PRE_SRC_SHIFT 20 -#define CRF_APB_VPLL_CTRL_PRE_SRC_MASK 0x00700000U - -/*The integer portion of the feedback divider to the PLL*/ -#undef CRF_APB_VPLL_CTRL_FBDIV_DEFVAL -#undef CRF_APB_VPLL_CTRL_FBDIV_SHIFT -#undef CRF_APB_VPLL_CTRL_FBDIV_MASK -#define CRF_APB_VPLL_CTRL_FBDIV_DEFVAL 0x00012809 -#define CRF_APB_VPLL_CTRL_FBDIV_SHIFT 8 -#define CRF_APB_VPLL_CTRL_FBDIV_MASK 0x00007F00U - -/*This turns on the divide by 2 that is inside of the PLL. This does not change the VCO frequency, just the output frequency*/ -#undef CRF_APB_VPLL_CTRL_DIV2_DEFVAL -#undef CRF_APB_VPLL_CTRL_DIV2_SHIFT -#undef CRF_APB_VPLL_CTRL_DIV2_MASK -#define CRF_APB_VPLL_CTRL_DIV2_DEFVAL 0x00012809 -#define CRF_APB_VPLL_CTRL_DIV2_SHIFT 16 -#define CRF_APB_VPLL_CTRL_DIV2_MASK 0x00010000U - -/*Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_VPLL_CTRL_BYPASS_DEFVAL -#undef CRF_APB_VPLL_CTRL_BYPASS_SHIFT -#undef CRF_APB_VPLL_CTRL_BYPASS_MASK -#define CRF_APB_VPLL_CTRL_BYPASS_DEFVAL 0x00012809 -#define CRF_APB_VPLL_CTRL_BYPASS_SHIFT 3 -#define CRF_APB_VPLL_CTRL_BYPASS_MASK 0x00000008U - -/*Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.*/ -#undef CRF_APB_VPLL_CTRL_RESET_DEFVAL -#undef CRF_APB_VPLL_CTRL_RESET_SHIFT -#undef CRF_APB_VPLL_CTRL_RESET_MASK -#define CRF_APB_VPLL_CTRL_RESET_DEFVAL 0x00012809 -#define CRF_APB_VPLL_CTRL_RESET_SHIFT 0 -#define CRF_APB_VPLL_CTRL_RESET_MASK 0x00000001U - -/*Asserts Reset to the PLL. When asserting reset, the PLL must already be in BYPASS.*/ -#undef CRF_APB_VPLL_CTRL_RESET_DEFVAL -#undef CRF_APB_VPLL_CTRL_RESET_SHIFT -#undef CRF_APB_VPLL_CTRL_RESET_MASK -#define CRF_APB_VPLL_CTRL_RESET_DEFVAL 0x00012809 -#define CRF_APB_VPLL_CTRL_RESET_SHIFT 0 -#define CRF_APB_VPLL_CTRL_RESET_MASK 0x00000001U - -/*VPLL is locked*/ -#undef CRF_APB_PLL_STATUS_VPLL_LOCK_DEFVAL -#undef CRF_APB_PLL_STATUS_VPLL_LOCK_SHIFT -#undef CRF_APB_PLL_STATUS_VPLL_LOCK_MASK -#define CRF_APB_PLL_STATUS_VPLL_LOCK_DEFVAL 0x00000038 -#define CRF_APB_PLL_STATUS_VPLL_LOCK_SHIFT 2 -#define CRF_APB_PLL_STATUS_VPLL_LOCK_MASK 0x00000004U -#define CRF_APB_PLL_STATUS_OFFSET 0XFD1A0044 - -/*Bypasses the PLL clock. The usable clock will be determined from the POST_SRC field. (This signal may only be toggled after 4 - cycles of the old clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_VPLL_CTRL_BYPASS_DEFVAL -#undef CRF_APB_VPLL_CTRL_BYPASS_SHIFT -#undef CRF_APB_VPLL_CTRL_BYPASS_MASK -#define CRF_APB_VPLL_CTRL_BYPASS_DEFVAL 0x00012809 -#define CRF_APB_VPLL_CTRL_BYPASS_SHIFT 3 -#define CRF_APB_VPLL_CTRL_BYPASS_MASK 0x00000008U - -/*Divisor value for this clock.*/ -#undef CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0_MASK -#define CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0_DEFVAL 0x00000400 -#define CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_VPLL_TO_LPD_CTRL_DIVISOR0_MASK 0x00003F00U - -/*Fractional SDM bypass control. When 0, PLL is in integer mode and it ignores all fractional data. When 1, PLL is in fractiona - mode and uses DATA of this register for the fractional portion of the feedback divider.*/ -#undef CRF_APB_VPLL_FRAC_CFG_ENABLED_DEFVAL -#undef CRF_APB_VPLL_FRAC_CFG_ENABLED_SHIFT -#undef CRF_APB_VPLL_FRAC_CFG_ENABLED_MASK -#define CRF_APB_VPLL_FRAC_CFG_ENABLED_DEFVAL 0x00000000 -#define CRF_APB_VPLL_FRAC_CFG_ENABLED_SHIFT 31 -#define CRF_APB_VPLL_FRAC_CFG_ENABLED_MASK 0x80000000U - -/*Fractional value for the Feedback value.*/ -#undef CRF_APB_VPLL_FRAC_CFG_DATA_DEFVAL -#undef CRF_APB_VPLL_FRAC_CFG_DATA_SHIFT -#undef CRF_APB_VPLL_FRAC_CFG_DATA_MASK -#define CRF_APB_VPLL_FRAC_CFG_DATA_DEFVAL 0x00000000 -#define CRF_APB_VPLL_FRAC_CFG_DATA_SHIFT 0 -#define CRF_APB_VPLL_FRAC_CFG_DATA_MASK 0x0000FFFFU -#undef CRL_APB_GEM3_REF_CTRL_OFFSET -#define CRL_APB_GEM3_REF_CTRL_OFFSET 0XFF5E005C -#undef CRL_APB_USB0_BUS_REF_CTRL_OFFSET -#define CRL_APB_USB0_BUS_REF_CTRL_OFFSET 0XFF5E0060 -#undef CRL_APB_USB3_DUAL_REF_CTRL_OFFSET -#define CRL_APB_USB3_DUAL_REF_CTRL_OFFSET 0XFF5E004C -#undef CRL_APB_QSPI_REF_CTRL_OFFSET -#define CRL_APB_QSPI_REF_CTRL_OFFSET 0XFF5E0068 -#undef CRL_APB_SDIO1_REF_CTRL_OFFSET -#define CRL_APB_SDIO1_REF_CTRL_OFFSET 0XFF5E0070 -#undef IOU_SLCR_SDIO_CLK_CTRL_OFFSET -#define IOU_SLCR_SDIO_CLK_CTRL_OFFSET 0XFF18030C -#undef CRL_APB_UART0_REF_CTRL_OFFSET -#define CRL_APB_UART0_REF_CTRL_OFFSET 0XFF5E0074 -#undef CRL_APB_UART1_REF_CTRL_OFFSET -#define CRL_APB_UART1_REF_CTRL_OFFSET 0XFF5E0078 -#undef CRL_APB_I2C0_REF_CTRL_OFFSET -#define CRL_APB_I2C0_REF_CTRL_OFFSET 0XFF5E0120 -#undef CRL_APB_I2C1_REF_CTRL_OFFSET -#define CRL_APB_I2C1_REF_CTRL_OFFSET 0XFF5E0124 -#undef CRL_APB_CAN1_REF_CTRL_OFFSET -#define CRL_APB_CAN1_REF_CTRL_OFFSET 0XFF5E0088 -#undef CRL_APB_CPU_R5_CTRL_OFFSET -#define CRL_APB_CPU_R5_CTRL_OFFSET 0XFF5E0090 -#undef CRL_APB_IOU_SWITCH_CTRL_OFFSET -#define CRL_APB_IOU_SWITCH_CTRL_OFFSET 0XFF5E009C -#undef CRL_APB_PCAP_CTRL_OFFSET -#define CRL_APB_PCAP_CTRL_OFFSET 0XFF5E00A4 -#undef CRL_APB_LPD_SWITCH_CTRL_OFFSET -#define CRL_APB_LPD_SWITCH_CTRL_OFFSET 0XFF5E00A8 -#undef CRL_APB_LPD_LSBUS_CTRL_OFFSET -#define CRL_APB_LPD_LSBUS_CTRL_OFFSET 0XFF5E00AC -#undef CRL_APB_DBG_LPD_CTRL_OFFSET -#define CRL_APB_DBG_LPD_CTRL_OFFSET 0XFF5E00B0 -#undef CRL_APB_ADMA_REF_CTRL_OFFSET -#define CRL_APB_ADMA_REF_CTRL_OFFSET 0XFF5E00B8 -#undef CRL_APB_PL0_REF_CTRL_OFFSET -#define CRL_APB_PL0_REF_CTRL_OFFSET 0XFF5E00C0 -#undef CRL_APB_PL1_REF_CTRL_OFFSET -#define CRL_APB_PL1_REF_CTRL_OFFSET 0XFF5E00C4 -#undef CRL_APB_PL2_REF_CTRL_OFFSET -#define CRL_APB_PL2_REF_CTRL_OFFSET 0XFF5E00C8 -#undef CRL_APB_PL3_REF_CTRL_OFFSET -#define CRL_APB_PL3_REF_CTRL_OFFSET 0XFF5E00CC -#undef CRL_APB_AMS_REF_CTRL_OFFSET -#define CRL_APB_AMS_REF_CTRL_OFFSET 0XFF5E0108 -#undef CRL_APB_DLL_REF_CTRL_OFFSET -#define CRL_APB_DLL_REF_CTRL_OFFSET 0XFF5E0104 -#undef CRL_APB_TIMESTAMP_REF_CTRL_OFFSET -#define CRL_APB_TIMESTAMP_REF_CTRL_OFFSET 0XFF5E0128 -#undef CRF_APB_SATA_REF_CTRL_OFFSET -#define CRF_APB_SATA_REF_CTRL_OFFSET 0XFD1A00A0 -#undef CRF_APB_DP_VIDEO_REF_CTRL_OFFSET -#define CRF_APB_DP_VIDEO_REF_CTRL_OFFSET 0XFD1A0070 -#undef CRF_APB_DP_AUDIO_REF_CTRL_OFFSET -#define CRF_APB_DP_AUDIO_REF_CTRL_OFFSET 0XFD1A0074 -#undef CRF_APB_DP_STC_REF_CTRL_OFFSET -#define CRF_APB_DP_STC_REF_CTRL_OFFSET 0XFD1A007C -#undef CRF_APB_ACPU_CTRL_OFFSET -#define CRF_APB_ACPU_CTRL_OFFSET 0XFD1A0060 -#undef CRF_APB_DBG_TRACE_CTRL_OFFSET -#define CRF_APB_DBG_TRACE_CTRL_OFFSET 0XFD1A0064 -#undef CRF_APB_DBG_FPD_CTRL_OFFSET -#define CRF_APB_DBG_FPD_CTRL_OFFSET 0XFD1A0068 -#undef CRF_APB_DDR_CTRL_OFFSET -#define CRF_APB_DDR_CTRL_OFFSET 0XFD1A0080 -#undef CRF_APB_GPU_REF_CTRL_OFFSET -#define CRF_APB_GPU_REF_CTRL_OFFSET 0XFD1A0084 -#undef CRF_APB_GDMA_REF_CTRL_OFFSET -#define CRF_APB_GDMA_REF_CTRL_OFFSET 0XFD1A00B8 -#undef CRF_APB_DPDMA_REF_CTRL_OFFSET -#define CRF_APB_DPDMA_REF_CTRL_OFFSET 0XFD1A00BC -#undef CRF_APB_TOPSW_MAIN_CTRL_OFFSET -#define CRF_APB_TOPSW_MAIN_CTRL_OFFSET 0XFD1A00C0 -#undef CRF_APB_TOPSW_LSBUS_CTRL_OFFSET -#define CRF_APB_TOPSW_LSBUS_CTRL_OFFSET 0XFD1A00C4 -#undef CRF_APB_DBG_TSTMP_CTRL_OFFSET -#define CRF_APB_DBG_TSTMP_CTRL_OFFSET 0XFD1A00F8 -#undef IOU_SLCR_IOU_TTC_APB_CLK_OFFSET -#define IOU_SLCR_IOU_TTC_APB_CLK_OFFSET 0XFF180380 -#undef FPD_SLCR_WDT_CLK_SEL_OFFSET -#define FPD_SLCR_WDT_CLK_SEL_OFFSET 0XFD610100 -#undef IOU_SLCR_WDT_CLK_SEL_OFFSET -#define IOU_SLCR_WDT_CLK_SEL_OFFSET 0XFF180300 -#undef LPD_SLCR_CSUPMU_WDT_CLK_SEL_OFFSET -#define LPD_SLCR_CSUPMU_WDT_CLK_SEL_OFFSET 0XFF410050 - -/*Clock active for the RX channel*/ -#undef CRL_APB_GEM3_REF_CTRL_RX_CLKACT_DEFVAL -#undef CRL_APB_GEM3_REF_CTRL_RX_CLKACT_SHIFT -#undef CRL_APB_GEM3_REF_CTRL_RX_CLKACT_MASK -#define CRL_APB_GEM3_REF_CTRL_RX_CLKACT_DEFVAL 0x00002500 -#define CRL_APB_GEM3_REF_CTRL_RX_CLKACT_SHIFT 26 -#define CRL_APB_GEM3_REF_CTRL_RX_CLKACT_MASK 0x04000000U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_GEM3_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_GEM3_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_GEM3_REF_CTRL_CLKACT_MASK -#define CRL_APB_GEM3_REF_CTRL_CLKACT_DEFVAL 0x00002500 -#define CRL_APB_GEM3_REF_CTRL_CLKACT_SHIFT 25 -#define CRL_APB_GEM3_REF_CTRL_CLKACT_MASK 0x02000000U - -/*6 bit divider*/ -#undef CRL_APB_GEM3_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_GEM3_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_GEM3_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_GEM3_REF_CTRL_DIVISOR1_DEFVAL 0x00002500 -#define CRL_APB_GEM3_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_GEM3_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_GEM3_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_GEM3_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_GEM3_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_GEM3_REF_CTRL_DIVISOR0_DEFVAL 0x00002500 -#define CRL_APB_GEM3_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_GEM3_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_GEM3_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_GEM3_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_GEM3_REF_CTRL_SRCSEL_MASK -#define CRL_APB_GEM3_REF_CTRL_SRCSEL_DEFVAL 0x00002500 -#define CRL_APB_GEM3_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_GEM3_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_USB0_BUS_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_USB0_BUS_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_USB0_BUS_REF_CTRL_CLKACT_MASK -#define CRL_APB_USB0_BUS_REF_CTRL_CLKACT_DEFVAL 0x00052000 -#define CRL_APB_USB0_BUS_REF_CTRL_CLKACT_SHIFT 25 -#define CRL_APB_USB0_BUS_REF_CTRL_CLKACT_MASK 0x02000000U - -/*6 bit divider*/ -#undef CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1_DEFVAL 0x00052000 -#define CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_USB0_BUS_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0_DEFVAL 0x00052000 -#define CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_USB0_BUS_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_USB0_BUS_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_USB0_BUS_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_USB0_BUS_REF_CTRL_SRCSEL_MASK -#define CRL_APB_USB0_BUS_REF_CTRL_SRCSEL_DEFVAL 0x00052000 -#define CRL_APB_USB0_BUS_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_USB0_BUS_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_USB3_DUAL_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_USB3_DUAL_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_USB3_DUAL_REF_CTRL_CLKACT_MASK -#define CRL_APB_USB3_DUAL_REF_CTRL_CLKACT_DEFVAL 0x00052000 -#define CRL_APB_USB3_DUAL_REF_CTRL_CLKACT_SHIFT 25 -#define CRL_APB_USB3_DUAL_REF_CTRL_CLKACT_MASK 0x02000000U - -/*6 bit divider*/ -#undef CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1_DEFVAL 0x00052000 -#define CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0_DEFVAL 0x00052000 -#define CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_USB3_DUAL_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL. (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL_MASK -#define CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL_DEFVAL 0x00052000 -#define CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_USB3_DUAL_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_QSPI_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_QSPI_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_QSPI_REF_CTRL_CLKACT_MASK -#define CRL_APB_QSPI_REF_CTRL_CLKACT_DEFVAL 0x01000800 -#define CRL_APB_QSPI_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_QSPI_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_QSPI_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_QSPI_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_QSPI_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_QSPI_REF_CTRL_DIVISOR1_DEFVAL 0x01000800 -#define CRL_APB_QSPI_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_QSPI_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_QSPI_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_QSPI_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_QSPI_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_QSPI_REF_CTRL_DIVISOR0_DEFVAL 0x01000800 -#define CRL_APB_QSPI_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_QSPI_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_QSPI_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_QSPI_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_QSPI_REF_CTRL_SRCSEL_MASK -#define CRL_APB_QSPI_REF_CTRL_SRCSEL_DEFVAL 0x01000800 -#define CRL_APB_QSPI_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_QSPI_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_SDIO1_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_SDIO1_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_SDIO1_REF_CTRL_CLKACT_MASK -#define CRL_APB_SDIO1_REF_CTRL_CLKACT_DEFVAL 0x01000F00 -#define CRL_APB_SDIO1_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_SDIO1_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_SDIO1_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_SDIO1_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_SDIO1_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_SDIO1_REF_CTRL_DIVISOR1_DEFVAL 0x01000F00 -#define CRL_APB_SDIO1_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_SDIO1_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_SDIO1_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_SDIO1_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_SDIO1_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_SDIO1_REF_CTRL_DIVISOR0_DEFVAL 0x01000F00 -#define CRL_APB_SDIO1_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_SDIO1_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = VPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_SDIO1_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_SDIO1_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_SDIO1_REF_CTRL_SRCSEL_MASK -#define CRL_APB_SDIO1_REF_CTRL_SRCSEL_DEFVAL 0x01000F00 -#define CRL_APB_SDIO1_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_SDIO1_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*MIO pad selection for sdio1_rx_clk (feedback clock from the PAD) 0: MIO [51] 1: MIO [76]*/ -#undef IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL_DEFVAL -#undef IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL_SHIFT -#undef IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL_MASK -#define IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL_SHIFT 17 -#define IOU_SLCR_SDIO_CLK_CTRL_SDIO1_RX_SRC_SEL_MASK 0x00020000U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_UART0_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_UART0_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_UART0_REF_CTRL_CLKACT_MASK -#define CRL_APB_UART0_REF_CTRL_CLKACT_DEFVAL 0x01001800 -#define CRL_APB_UART0_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_UART0_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_UART0_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_UART0_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_UART0_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_UART0_REF_CTRL_DIVISOR1_DEFVAL 0x01001800 -#define CRL_APB_UART0_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_UART0_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_UART0_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_UART0_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_UART0_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_UART0_REF_CTRL_DIVISOR0_DEFVAL 0x01001800 -#define CRL_APB_UART0_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_UART0_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_UART0_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_UART0_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_UART0_REF_CTRL_SRCSEL_MASK -#define CRL_APB_UART0_REF_CTRL_SRCSEL_DEFVAL 0x01001800 -#define CRL_APB_UART0_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_UART0_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_UART1_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_UART1_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_UART1_REF_CTRL_CLKACT_MASK -#define CRL_APB_UART1_REF_CTRL_CLKACT_DEFVAL 0x01001800 -#define CRL_APB_UART1_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_UART1_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_UART1_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_UART1_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_UART1_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_UART1_REF_CTRL_DIVISOR1_DEFVAL 0x01001800 -#define CRL_APB_UART1_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_UART1_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_UART1_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_UART1_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_UART1_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_UART1_REF_CTRL_DIVISOR0_DEFVAL 0x01001800 -#define CRL_APB_UART1_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_UART1_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_UART1_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_UART1_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_UART1_REF_CTRL_SRCSEL_MASK -#define CRL_APB_UART1_REF_CTRL_SRCSEL_DEFVAL 0x01001800 -#define CRL_APB_UART1_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_UART1_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_I2C0_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_I2C0_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_I2C0_REF_CTRL_CLKACT_MASK -#define CRL_APB_I2C0_REF_CTRL_CLKACT_DEFVAL 0x01000500 -#define CRL_APB_I2C0_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_I2C0_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_I2C0_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_I2C0_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_I2C0_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_I2C0_REF_CTRL_DIVISOR1_DEFVAL 0x01000500 -#define CRL_APB_I2C0_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_I2C0_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_I2C0_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_I2C0_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_I2C0_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_I2C0_REF_CTRL_DIVISOR0_DEFVAL 0x01000500 -#define CRL_APB_I2C0_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_I2C0_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_I2C0_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_I2C0_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_I2C0_REF_CTRL_SRCSEL_MASK -#define CRL_APB_I2C0_REF_CTRL_SRCSEL_DEFVAL 0x01000500 -#define CRL_APB_I2C0_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_I2C0_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_I2C1_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_I2C1_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_I2C1_REF_CTRL_CLKACT_MASK -#define CRL_APB_I2C1_REF_CTRL_CLKACT_DEFVAL 0x01000500 -#define CRL_APB_I2C1_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_I2C1_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_I2C1_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_I2C1_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_I2C1_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_I2C1_REF_CTRL_DIVISOR1_DEFVAL 0x01000500 -#define CRL_APB_I2C1_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_I2C1_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_I2C1_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_I2C1_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_I2C1_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_I2C1_REF_CTRL_DIVISOR0_DEFVAL 0x01000500 -#define CRL_APB_I2C1_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_I2C1_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_I2C1_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_I2C1_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_I2C1_REF_CTRL_SRCSEL_MASK -#define CRL_APB_I2C1_REF_CTRL_SRCSEL_DEFVAL 0x01000500 -#define CRL_APB_I2C1_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_I2C1_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_CAN1_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_CAN1_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_CAN1_REF_CTRL_CLKACT_MASK -#define CRL_APB_CAN1_REF_CTRL_CLKACT_DEFVAL 0x01001800 -#define CRL_APB_CAN1_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_CAN1_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_CAN1_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_CAN1_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_CAN1_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_CAN1_REF_CTRL_DIVISOR1_DEFVAL 0x01001800 -#define CRL_APB_CAN1_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_CAN1_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_CAN1_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_CAN1_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_CAN1_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_CAN1_REF_CTRL_DIVISOR0_DEFVAL 0x01001800 -#define CRL_APB_CAN1_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_CAN1_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_CAN1_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_CAN1_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_CAN1_REF_CTRL_SRCSEL_MASK -#define CRL_APB_CAN1_REF_CTRL_SRCSEL_DEFVAL 0x01001800 -#define CRL_APB_CAN1_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_CAN1_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Turing this off will shut down the OCM, some parts of the APM, and prevent transactions going from the FPD to the LPD and cou - d lead to system hang*/ -#undef CRL_APB_CPU_R5_CTRL_CLKACT_DEFVAL -#undef CRL_APB_CPU_R5_CTRL_CLKACT_SHIFT -#undef CRL_APB_CPU_R5_CTRL_CLKACT_MASK -#define CRL_APB_CPU_R5_CTRL_CLKACT_DEFVAL 0x03000600 -#define CRL_APB_CPU_R5_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_CPU_R5_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_CPU_R5_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_CPU_R5_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_CPU_R5_CTRL_DIVISOR0_MASK -#define CRL_APB_CPU_R5_CTRL_DIVISOR0_DEFVAL 0x03000600 -#define CRL_APB_CPU_R5_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_CPU_R5_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_CPU_R5_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_CPU_R5_CTRL_SRCSEL_SHIFT -#undef CRL_APB_CPU_R5_CTRL_SRCSEL_MASK -#define CRL_APB_CPU_R5_CTRL_SRCSEL_DEFVAL 0x03000600 -#define CRL_APB_CPU_R5_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_CPU_R5_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_IOU_SWITCH_CTRL_CLKACT_DEFVAL -#undef CRL_APB_IOU_SWITCH_CTRL_CLKACT_SHIFT -#undef CRL_APB_IOU_SWITCH_CTRL_CLKACT_MASK -#define CRL_APB_IOU_SWITCH_CTRL_CLKACT_DEFVAL 0x00001500 -#define CRL_APB_IOU_SWITCH_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_IOU_SWITCH_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_IOU_SWITCH_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_IOU_SWITCH_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_IOU_SWITCH_CTRL_DIVISOR0_MASK -#define CRL_APB_IOU_SWITCH_CTRL_DIVISOR0_DEFVAL 0x00001500 -#define CRL_APB_IOU_SWITCH_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_IOU_SWITCH_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_IOU_SWITCH_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_IOU_SWITCH_CTRL_SRCSEL_SHIFT -#undef CRL_APB_IOU_SWITCH_CTRL_SRCSEL_MASK -#define CRL_APB_IOU_SWITCH_CTRL_SRCSEL_DEFVAL 0x00001500 -#define CRL_APB_IOU_SWITCH_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_IOU_SWITCH_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_PCAP_CTRL_CLKACT_DEFVAL -#undef CRL_APB_PCAP_CTRL_CLKACT_SHIFT -#undef CRL_APB_PCAP_CTRL_CLKACT_MASK -#define CRL_APB_PCAP_CTRL_CLKACT_DEFVAL 0x00001500 -#define CRL_APB_PCAP_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_PCAP_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_PCAP_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_PCAP_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_PCAP_CTRL_DIVISOR0_MASK -#define CRL_APB_PCAP_CTRL_DIVISOR0_DEFVAL 0x00001500 -#define CRL_APB_PCAP_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_PCAP_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_PCAP_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_PCAP_CTRL_SRCSEL_SHIFT -#undef CRL_APB_PCAP_CTRL_SRCSEL_MASK -#define CRL_APB_PCAP_CTRL_SRCSEL_DEFVAL 0x00001500 -#define CRL_APB_PCAP_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_PCAP_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_LPD_SWITCH_CTRL_CLKACT_DEFVAL -#undef CRL_APB_LPD_SWITCH_CTRL_CLKACT_SHIFT -#undef CRL_APB_LPD_SWITCH_CTRL_CLKACT_MASK -#define CRL_APB_LPD_SWITCH_CTRL_CLKACT_DEFVAL 0x01000500 -#define CRL_APB_LPD_SWITCH_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_LPD_SWITCH_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_LPD_SWITCH_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_LPD_SWITCH_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_LPD_SWITCH_CTRL_DIVISOR0_MASK -#define CRL_APB_LPD_SWITCH_CTRL_DIVISOR0_DEFVAL 0x01000500 -#define CRL_APB_LPD_SWITCH_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_LPD_SWITCH_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_LPD_SWITCH_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_LPD_SWITCH_CTRL_SRCSEL_SHIFT -#undef CRL_APB_LPD_SWITCH_CTRL_SRCSEL_MASK -#define CRL_APB_LPD_SWITCH_CTRL_SRCSEL_DEFVAL 0x01000500 -#define CRL_APB_LPD_SWITCH_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_LPD_SWITCH_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_LPD_LSBUS_CTRL_CLKACT_DEFVAL -#undef CRL_APB_LPD_LSBUS_CTRL_CLKACT_SHIFT -#undef CRL_APB_LPD_LSBUS_CTRL_CLKACT_MASK -#define CRL_APB_LPD_LSBUS_CTRL_CLKACT_DEFVAL 0x01001800 -#define CRL_APB_LPD_LSBUS_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_LPD_LSBUS_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_LPD_LSBUS_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_LPD_LSBUS_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_LPD_LSBUS_CTRL_DIVISOR0_MASK -#define CRL_APB_LPD_LSBUS_CTRL_DIVISOR0_DEFVAL 0x01001800 -#define CRL_APB_LPD_LSBUS_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_LPD_LSBUS_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_LPD_LSBUS_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_LPD_LSBUS_CTRL_SRCSEL_SHIFT -#undef CRL_APB_LPD_LSBUS_CTRL_SRCSEL_MASK -#define CRL_APB_LPD_LSBUS_CTRL_SRCSEL_DEFVAL 0x01001800 -#define CRL_APB_LPD_LSBUS_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_LPD_LSBUS_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_DBG_LPD_CTRL_CLKACT_DEFVAL -#undef CRL_APB_DBG_LPD_CTRL_CLKACT_SHIFT -#undef CRL_APB_DBG_LPD_CTRL_CLKACT_MASK -#define CRL_APB_DBG_LPD_CTRL_CLKACT_DEFVAL 0x01002000 -#define CRL_APB_DBG_LPD_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_DBG_LPD_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_DBG_LPD_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_DBG_LPD_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_DBG_LPD_CTRL_DIVISOR0_MASK -#define CRL_APB_DBG_LPD_CTRL_DIVISOR0_DEFVAL 0x01002000 -#define CRL_APB_DBG_LPD_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_DBG_LPD_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_DBG_LPD_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_DBG_LPD_CTRL_SRCSEL_SHIFT -#undef CRL_APB_DBG_LPD_CTRL_SRCSEL_MASK -#define CRL_APB_DBG_LPD_CTRL_SRCSEL_DEFVAL 0x01002000 -#define CRL_APB_DBG_LPD_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_DBG_LPD_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_ADMA_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_ADMA_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_ADMA_REF_CTRL_CLKACT_MASK -#define CRL_APB_ADMA_REF_CTRL_CLKACT_DEFVAL 0x00002000 -#define CRL_APB_ADMA_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_ADMA_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_ADMA_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_ADMA_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_ADMA_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_ADMA_REF_CTRL_DIVISOR0_DEFVAL 0x00002000 -#define CRL_APB_ADMA_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_ADMA_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_ADMA_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_ADMA_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_ADMA_REF_CTRL_SRCSEL_MASK -#define CRL_APB_ADMA_REF_CTRL_SRCSEL_DEFVAL 0x00002000 -#define CRL_APB_ADMA_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_ADMA_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_PL0_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_PL0_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_PL0_REF_CTRL_CLKACT_MASK -#define CRL_APB_PL0_REF_CTRL_CLKACT_DEFVAL 0x00052000 -#define CRL_APB_PL0_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_PL0_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_PL0_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_PL0_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_PL0_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_PL0_REF_CTRL_DIVISOR1_DEFVAL 0x00052000 -#define CRL_APB_PL0_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_PL0_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_PL0_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_PL0_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_PL0_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_PL0_REF_CTRL_DIVISOR0_DEFVAL 0x00052000 -#define CRL_APB_PL0_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_PL0_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_PL0_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_PL0_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_PL0_REF_CTRL_SRCSEL_MASK -#define CRL_APB_PL0_REF_CTRL_SRCSEL_DEFVAL 0x00052000 -#define CRL_APB_PL0_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_PL0_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_PL1_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_PL1_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_PL1_REF_CTRL_CLKACT_MASK -#define CRL_APB_PL1_REF_CTRL_CLKACT_DEFVAL 0x00052000 -#define CRL_APB_PL1_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_PL1_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_PL1_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_PL1_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_PL1_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_PL1_REF_CTRL_DIVISOR1_DEFVAL 0x00052000 -#define CRL_APB_PL1_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_PL1_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_PL1_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_PL1_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_PL1_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_PL1_REF_CTRL_DIVISOR0_DEFVAL 0x00052000 -#define CRL_APB_PL1_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_PL1_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_PL1_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_PL1_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_PL1_REF_CTRL_SRCSEL_MASK -#define CRL_APB_PL1_REF_CTRL_SRCSEL_DEFVAL 0x00052000 -#define CRL_APB_PL1_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_PL1_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_PL2_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_PL2_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_PL2_REF_CTRL_CLKACT_MASK -#define CRL_APB_PL2_REF_CTRL_CLKACT_DEFVAL 0x00052000 -#define CRL_APB_PL2_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_PL2_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_PL2_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_PL2_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_PL2_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_PL2_REF_CTRL_DIVISOR1_DEFVAL 0x00052000 -#define CRL_APB_PL2_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_PL2_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_PL2_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_PL2_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_PL2_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_PL2_REF_CTRL_DIVISOR0_DEFVAL 0x00052000 -#define CRL_APB_PL2_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_PL2_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_PL2_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_PL2_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_PL2_REF_CTRL_SRCSEL_MASK -#define CRL_APB_PL2_REF_CTRL_SRCSEL_DEFVAL 0x00052000 -#define CRL_APB_PL2_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_PL2_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_PL3_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_PL3_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_PL3_REF_CTRL_CLKACT_MASK -#define CRL_APB_PL3_REF_CTRL_CLKACT_DEFVAL 0x00052000 -#define CRL_APB_PL3_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_PL3_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRL_APB_PL3_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_PL3_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_PL3_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_PL3_REF_CTRL_DIVISOR1_DEFVAL 0x00052000 -#define CRL_APB_PL3_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_PL3_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_PL3_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_PL3_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_PL3_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_PL3_REF_CTRL_DIVISOR0_DEFVAL 0x00052000 -#define CRL_APB_PL3_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_PL3_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_PL3_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_PL3_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_PL3_REF_CTRL_SRCSEL_MASK -#define CRL_APB_PL3_REF_CTRL_SRCSEL_DEFVAL 0x00052000 -#define CRL_APB_PL3_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_PL3_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*6 bit divider*/ -#undef CRL_APB_AMS_REF_CTRL_DIVISOR1_DEFVAL -#undef CRL_APB_AMS_REF_CTRL_DIVISOR1_SHIFT -#undef CRL_APB_AMS_REF_CTRL_DIVISOR1_MASK -#define CRL_APB_AMS_REF_CTRL_DIVISOR1_DEFVAL 0x01001800 -#define CRL_APB_AMS_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRL_APB_AMS_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRL_APB_AMS_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_AMS_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_AMS_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_AMS_REF_CTRL_DIVISOR0_DEFVAL 0x01001800 -#define CRL_APB_AMS_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_AMS_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = RPLL; 010 = IOPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_AMS_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_AMS_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_AMS_REF_CTRL_SRCSEL_MASK -#define CRL_APB_AMS_REF_CTRL_SRCSEL_DEFVAL 0x01001800 -#define CRL_APB_AMS_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_AMS_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_AMS_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_AMS_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_AMS_REF_CTRL_CLKACT_MASK -#define CRL_APB_AMS_REF_CTRL_CLKACT_DEFVAL 0x01001800 -#define CRL_APB_AMS_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_AMS_REF_CTRL_CLKACT_MASK 0x01000000U - -/*000 = IOPLL; 001 = RPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new clock. This - is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_DLL_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_DLL_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_DLL_REF_CTRL_SRCSEL_MASK -#define CRL_APB_DLL_REF_CTRL_SRCSEL_DEFVAL 0x00000000 -#define CRL_APB_DLL_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_DLL_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*6 bit divider*/ -#undef CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0_DEFVAL -#undef CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0_SHIFT -#undef CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0_MASK -#define CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0_DEFVAL 0x00001800 -#define CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRL_APB_TIMESTAMP_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*1XX = pss_ref_clk; 000 = IOPLL; 010 = RPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and - cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL_DEFVAL -#undef CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL_SHIFT -#undef CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL_MASK -#define CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL_DEFVAL 0x00001800 -#define CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL_SHIFT 0 -#define CRL_APB_TIMESTAMP_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRL_APB_TIMESTAMP_REF_CTRL_CLKACT_DEFVAL -#undef CRL_APB_TIMESTAMP_REF_CTRL_CLKACT_SHIFT -#undef CRL_APB_TIMESTAMP_REF_CTRL_CLKACT_MASK -#define CRL_APB_TIMESTAMP_REF_CTRL_CLKACT_DEFVAL 0x00001800 -#define CRL_APB_TIMESTAMP_REF_CTRL_CLKACT_SHIFT 24 -#define CRL_APB_TIMESTAMP_REF_CTRL_CLKACT_MASK 0x01000000U - -/*000 = IOPLL_TO_FPD; 010 = APLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_SATA_REF_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_SATA_REF_CTRL_SRCSEL_SHIFT -#undef CRF_APB_SATA_REF_CTRL_SRCSEL_MASK -#define CRF_APB_SATA_REF_CTRL_SRCSEL_DEFVAL 0x01001600 -#define CRF_APB_SATA_REF_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_SATA_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRF_APB_SATA_REF_CTRL_CLKACT_DEFVAL -#undef CRF_APB_SATA_REF_CTRL_CLKACT_SHIFT -#undef CRF_APB_SATA_REF_CTRL_CLKACT_MASK -#define CRF_APB_SATA_REF_CTRL_CLKACT_DEFVAL 0x01001600 -#define CRF_APB_SATA_REF_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_SATA_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_SATA_REF_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_SATA_REF_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_SATA_REF_CTRL_DIVISOR0_MASK -#define CRF_APB_SATA_REF_CTRL_DIVISOR0_DEFVAL 0x01001600 -#define CRF_APB_SATA_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_SATA_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*6 bit divider*/ -#undef CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1_DEFVAL -#undef CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1_SHIFT -#undef CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1_MASK -#define CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1_DEFVAL 0x01002300 -#define CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0_MASK -#define CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0_DEFVAL 0x01002300 -#define CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_DP_VIDEO_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD - might be using extra mux; (This signal may only be toggled after 4 cycles of the - ld clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL_SHIFT -#undef CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL_MASK -#define CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL_DEFVAL 0x01002300 -#define CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_DP_VIDEO_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRF_APB_DP_VIDEO_REF_CTRL_CLKACT_DEFVAL -#undef CRF_APB_DP_VIDEO_REF_CTRL_CLKACT_SHIFT -#undef CRF_APB_DP_VIDEO_REF_CTRL_CLKACT_MASK -#define CRF_APB_DP_VIDEO_REF_CTRL_CLKACT_DEFVAL 0x01002300 -#define CRF_APB_DP_VIDEO_REF_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_DP_VIDEO_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1_DEFVAL -#undef CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1_SHIFT -#undef CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1_MASK -#define CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1_DEFVAL 0x01032300 -#define CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0_MASK -#define CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0_DEFVAL 0x01032300 -#define CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_DP_AUDIO_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD - might be using extra mux; (This signal may only be toggled after 4 cycles of the - ld clock and 4 cycles of the new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL_SHIFT -#undef CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL_MASK -#define CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL_DEFVAL 0x01032300 -#define CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_DP_AUDIO_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRF_APB_DP_AUDIO_REF_CTRL_CLKACT_DEFVAL -#undef CRF_APB_DP_AUDIO_REF_CTRL_CLKACT_SHIFT -#undef CRF_APB_DP_AUDIO_REF_CTRL_CLKACT_MASK -#define CRF_APB_DP_AUDIO_REF_CTRL_CLKACT_DEFVAL 0x01032300 -#define CRF_APB_DP_AUDIO_REF_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_DP_AUDIO_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_DP_STC_REF_CTRL_DIVISOR1_DEFVAL -#undef CRF_APB_DP_STC_REF_CTRL_DIVISOR1_SHIFT -#undef CRF_APB_DP_STC_REF_CTRL_DIVISOR1_MASK -#define CRF_APB_DP_STC_REF_CTRL_DIVISOR1_DEFVAL 0x01203200 -#define CRF_APB_DP_STC_REF_CTRL_DIVISOR1_SHIFT 16 -#define CRF_APB_DP_STC_REF_CTRL_DIVISOR1_MASK 0x003F0000U - -/*6 bit divider*/ -#undef CRF_APB_DP_STC_REF_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_DP_STC_REF_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_DP_STC_REF_CTRL_DIVISOR0_MASK -#define CRF_APB_DP_STC_REF_CTRL_DIVISOR0_DEFVAL 0x01203200 -#define CRF_APB_DP_STC_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_DP_STC_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = VPLL; 010 = DPLL; 011 = RPLL_TO_FPD; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of t - e new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_DP_STC_REF_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_DP_STC_REF_CTRL_SRCSEL_SHIFT -#undef CRF_APB_DP_STC_REF_CTRL_SRCSEL_MASK -#define CRF_APB_DP_STC_REF_CTRL_SRCSEL_DEFVAL 0x01203200 -#define CRF_APB_DP_STC_REF_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_DP_STC_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRF_APB_DP_STC_REF_CTRL_CLKACT_DEFVAL -#undef CRF_APB_DP_STC_REF_CTRL_CLKACT_SHIFT -#undef CRF_APB_DP_STC_REF_CTRL_CLKACT_MASK -#define CRF_APB_DP_STC_REF_CTRL_CLKACT_DEFVAL 0x01203200 -#define CRF_APB_DP_STC_REF_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_DP_STC_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_ACPU_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_ACPU_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_ACPU_CTRL_DIVISOR0_MASK -#define CRF_APB_ACPU_CTRL_DIVISOR0_DEFVAL 0x03000400 -#define CRF_APB_ACPU_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_ACPU_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = APLL; 010 = DPLL; 011 = VPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - lock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_ACPU_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_ACPU_CTRL_SRCSEL_SHIFT -#undef CRF_APB_ACPU_CTRL_SRCSEL_MASK -#define CRF_APB_ACPU_CTRL_SRCSEL_DEFVAL 0x03000400 -#define CRF_APB_ACPU_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_ACPU_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock. For the half speed APU Clock*/ -#undef CRF_APB_ACPU_CTRL_CLKACT_HALF_DEFVAL -#undef CRF_APB_ACPU_CTRL_CLKACT_HALF_SHIFT -#undef CRF_APB_ACPU_CTRL_CLKACT_HALF_MASK -#define CRF_APB_ACPU_CTRL_CLKACT_HALF_DEFVAL 0x03000400 -#define CRF_APB_ACPU_CTRL_CLKACT_HALF_SHIFT 25 -#define CRF_APB_ACPU_CTRL_CLKACT_HALF_MASK 0x02000000U - -/*Clock active signal. Switch to 0 to disable the clock. For the full speed ACPUX Clock. This will shut off the high speed cloc - to the entire APU*/ -#undef CRF_APB_ACPU_CTRL_CLKACT_FULL_DEFVAL -#undef CRF_APB_ACPU_CTRL_CLKACT_FULL_SHIFT -#undef CRF_APB_ACPU_CTRL_CLKACT_FULL_MASK -#define CRF_APB_ACPU_CTRL_CLKACT_FULL_DEFVAL 0x03000400 -#define CRF_APB_ACPU_CTRL_CLKACT_FULL_SHIFT 24 -#define CRF_APB_ACPU_CTRL_CLKACT_FULL_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_DBG_TRACE_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_DBG_TRACE_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_DBG_TRACE_CTRL_DIVISOR0_MASK -#define CRF_APB_DBG_TRACE_CTRL_DIVISOR0_DEFVAL 0x00002500 -#define CRF_APB_DBG_TRACE_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_DBG_TRACE_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_DBG_TRACE_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_DBG_TRACE_CTRL_SRCSEL_SHIFT -#undef CRF_APB_DBG_TRACE_CTRL_SRCSEL_MASK -#define CRF_APB_DBG_TRACE_CTRL_SRCSEL_DEFVAL 0x00002500 -#define CRF_APB_DBG_TRACE_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_DBG_TRACE_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRF_APB_DBG_TRACE_CTRL_CLKACT_DEFVAL -#undef CRF_APB_DBG_TRACE_CTRL_CLKACT_SHIFT -#undef CRF_APB_DBG_TRACE_CTRL_CLKACT_MASK -#define CRF_APB_DBG_TRACE_CTRL_CLKACT_DEFVAL 0x00002500 -#define CRF_APB_DBG_TRACE_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_DBG_TRACE_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_DBG_FPD_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_DBG_FPD_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_DBG_FPD_CTRL_DIVISOR0_MASK -#define CRF_APB_DBG_FPD_CTRL_DIVISOR0_DEFVAL 0x01002500 -#define CRF_APB_DBG_FPD_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_DBG_FPD_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_DBG_FPD_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_DBG_FPD_CTRL_SRCSEL_SHIFT -#undef CRF_APB_DBG_FPD_CTRL_SRCSEL_MASK -#define CRF_APB_DBG_FPD_CTRL_SRCSEL_DEFVAL 0x01002500 -#define CRF_APB_DBG_FPD_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_DBG_FPD_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRF_APB_DBG_FPD_CTRL_CLKACT_DEFVAL -#undef CRF_APB_DBG_FPD_CTRL_CLKACT_SHIFT -#undef CRF_APB_DBG_FPD_CTRL_CLKACT_MASK -#define CRF_APB_DBG_FPD_CTRL_CLKACT_DEFVAL 0x01002500 -#define CRF_APB_DBG_FPD_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_DBG_FPD_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_DDR_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_DDR_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_DDR_CTRL_DIVISOR0_MASK -#define CRF_APB_DDR_CTRL_DIVISOR0_DEFVAL 0x01000500 -#define CRF_APB_DDR_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_DDR_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = DPLL; 001 = VPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new clock. This - s not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_DDR_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_DDR_CTRL_SRCSEL_SHIFT -#undef CRF_APB_DDR_CTRL_SRCSEL_MASK -#define CRF_APB_DDR_CTRL_SRCSEL_DEFVAL 0x01000500 -#define CRF_APB_DDR_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_DDR_CTRL_SRCSEL_MASK 0x00000007U - -/*6 bit divider*/ -#undef CRF_APB_GPU_REF_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_GPU_REF_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_GPU_REF_CTRL_DIVISOR0_MASK -#define CRF_APB_GPU_REF_CTRL_DIVISOR0_DEFVAL 0x00001500 -#define CRF_APB_GPU_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_GPU_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL_TO_FPD; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_GPU_REF_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_GPU_REF_CTRL_SRCSEL_SHIFT -#undef CRF_APB_GPU_REF_CTRL_SRCSEL_MASK -#define CRF_APB_GPU_REF_CTRL_SRCSEL_DEFVAL 0x00001500 -#define CRF_APB_GPU_REF_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_GPU_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock, which will stop clock for GPU (and both Pixel Processors).*/ -#undef CRF_APB_GPU_REF_CTRL_CLKACT_DEFVAL -#undef CRF_APB_GPU_REF_CTRL_CLKACT_SHIFT -#undef CRF_APB_GPU_REF_CTRL_CLKACT_MASK -#define CRF_APB_GPU_REF_CTRL_CLKACT_DEFVAL 0x00001500 -#define CRF_APB_GPU_REF_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_GPU_REF_CTRL_CLKACT_MASK 0x01000000U - -/*Clock active signal for Pixel Processor. Switch to 0 to disable the clock only to this Pixel Processor*/ -#undef CRF_APB_GPU_REF_CTRL_PP0_CLKACT_DEFVAL -#undef CRF_APB_GPU_REF_CTRL_PP0_CLKACT_SHIFT -#undef CRF_APB_GPU_REF_CTRL_PP0_CLKACT_MASK -#define CRF_APB_GPU_REF_CTRL_PP0_CLKACT_DEFVAL 0x00001500 -#define CRF_APB_GPU_REF_CTRL_PP0_CLKACT_SHIFT 25 -#define CRF_APB_GPU_REF_CTRL_PP0_CLKACT_MASK 0x02000000U - -/*Clock active signal for Pixel Processor. Switch to 0 to disable the clock only to this Pixel Processor*/ -#undef CRF_APB_GPU_REF_CTRL_PP1_CLKACT_DEFVAL -#undef CRF_APB_GPU_REF_CTRL_PP1_CLKACT_SHIFT -#undef CRF_APB_GPU_REF_CTRL_PP1_CLKACT_MASK -#define CRF_APB_GPU_REF_CTRL_PP1_CLKACT_DEFVAL 0x00001500 -#define CRF_APB_GPU_REF_CTRL_PP1_CLKACT_SHIFT 26 -#define CRF_APB_GPU_REF_CTRL_PP1_CLKACT_MASK 0x04000000U - -/*6 bit divider*/ -#undef CRF_APB_GDMA_REF_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_GDMA_REF_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_GDMA_REF_CTRL_DIVISOR0_MASK -#define CRF_APB_GDMA_REF_CTRL_DIVISOR0_DEFVAL 0x01000500 -#define CRF_APB_GDMA_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_GDMA_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - lock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_GDMA_REF_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_GDMA_REF_CTRL_SRCSEL_SHIFT -#undef CRF_APB_GDMA_REF_CTRL_SRCSEL_MASK -#define CRF_APB_GDMA_REF_CTRL_SRCSEL_DEFVAL 0x01000500 -#define CRF_APB_GDMA_REF_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_GDMA_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRF_APB_GDMA_REF_CTRL_CLKACT_DEFVAL -#undef CRF_APB_GDMA_REF_CTRL_CLKACT_SHIFT -#undef CRF_APB_GDMA_REF_CTRL_CLKACT_MASK -#define CRF_APB_GDMA_REF_CTRL_CLKACT_DEFVAL 0x01000500 -#define CRF_APB_GDMA_REF_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_GDMA_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_DPDMA_REF_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_DPDMA_REF_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_DPDMA_REF_CTRL_DIVISOR0_MASK -#define CRF_APB_DPDMA_REF_CTRL_DIVISOR0_DEFVAL 0x01000500 -#define CRF_APB_DPDMA_REF_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_DPDMA_REF_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - lock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_DPDMA_REF_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_DPDMA_REF_CTRL_SRCSEL_SHIFT -#undef CRF_APB_DPDMA_REF_CTRL_SRCSEL_MASK -#define CRF_APB_DPDMA_REF_CTRL_SRCSEL_DEFVAL 0x01000500 -#define CRF_APB_DPDMA_REF_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_DPDMA_REF_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRF_APB_DPDMA_REF_CTRL_CLKACT_DEFVAL -#undef CRF_APB_DPDMA_REF_CTRL_CLKACT_SHIFT -#undef CRF_APB_DPDMA_REF_CTRL_CLKACT_MASK -#define CRF_APB_DPDMA_REF_CTRL_CLKACT_DEFVAL 0x01000500 -#define CRF_APB_DPDMA_REF_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_DPDMA_REF_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0_MASK -#define CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0_DEFVAL 0x01000400 -#define CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_TOPSW_MAIN_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = APLL; 010 = VPLL; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of the new - lock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_TOPSW_MAIN_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_TOPSW_MAIN_CTRL_SRCSEL_SHIFT -#undef CRF_APB_TOPSW_MAIN_CTRL_SRCSEL_MASK -#define CRF_APB_TOPSW_MAIN_CTRL_SRCSEL_DEFVAL 0x01000400 -#define CRF_APB_TOPSW_MAIN_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_TOPSW_MAIN_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRF_APB_TOPSW_MAIN_CTRL_CLKACT_DEFVAL -#undef CRF_APB_TOPSW_MAIN_CTRL_CLKACT_SHIFT -#undef CRF_APB_TOPSW_MAIN_CTRL_CLKACT_MASK -#define CRF_APB_TOPSW_MAIN_CTRL_CLKACT_DEFVAL 0x01000400 -#define CRF_APB_TOPSW_MAIN_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_TOPSW_MAIN_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0_MASK -#define CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0_DEFVAL 0x01000800 -#define CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_TOPSW_LSBUS_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = APLL; 010 = IOPLL_TO_FPD; 011 = DPLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL_SHIFT -#undef CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL_MASK -#define CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL_DEFVAL 0x01000800 -#define CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_TOPSW_LSBUS_CTRL_SRCSEL_MASK 0x00000007U - -/*Clock active signal. Switch to 0 to disable the clock*/ -#undef CRF_APB_TOPSW_LSBUS_CTRL_CLKACT_DEFVAL -#undef CRF_APB_TOPSW_LSBUS_CTRL_CLKACT_SHIFT -#undef CRF_APB_TOPSW_LSBUS_CTRL_CLKACT_MASK -#define CRF_APB_TOPSW_LSBUS_CTRL_CLKACT_DEFVAL 0x01000800 -#define CRF_APB_TOPSW_LSBUS_CTRL_CLKACT_SHIFT 24 -#define CRF_APB_TOPSW_LSBUS_CTRL_CLKACT_MASK 0x01000000U - -/*6 bit divider*/ -#undef CRF_APB_DBG_TSTMP_CTRL_DIVISOR0_DEFVAL -#undef CRF_APB_DBG_TSTMP_CTRL_DIVISOR0_SHIFT -#undef CRF_APB_DBG_TSTMP_CTRL_DIVISOR0_MASK -#define CRF_APB_DBG_TSTMP_CTRL_DIVISOR0_DEFVAL 0x00000A00 -#define CRF_APB_DBG_TSTMP_CTRL_DIVISOR0_SHIFT 8 -#define CRF_APB_DBG_TSTMP_CTRL_DIVISOR0_MASK 0x00003F00U - -/*000 = IOPLL_TO_FPD; 010 = DPLL; 011 = APLL; (This signal may only be toggled after 4 cycles of the old clock and 4 cycles of - he new clock. This is not usually an issue, but designers must be aware.)*/ -#undef CRF_APB_DBG_TSTMP_CTRL_SRCSEL_DEFVAL -#undef CRF_APB_DBG_TSTMP_CTRL_SRCSEL_SHIFT -#undef CRF_APB_DBG_TSTMP_CTRL_SRCSEL_MASK -#define CRF_APB_DBG_TSTMP_CTRL_SRCSEL_DEFVAL 0x00000A00 -#define CRF_APB_DBG_TSTMP_CTRL_SRCSEL_SHIFT 0 -#define CRF_APB_DBG_TSTMP_CTRL_SRCSEL_MASK 0x00000007U - -/*00" = Select the APB switch clock for the APB interface of TTC0'01" = Select the PLL ref clock for the APB interface of TTC0' - 0" = Select the R5 clock for the APB interface of TTC0*/ -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL_DEFVAL -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL_SHIFT -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL_MASK -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL_SHIFT 0 -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC0_SEL_MASK 0x00000003U - -/*00" = Select the APB switch clock for the APB interface of TTC1'01" = Select the PLL ref clock for the APB interface of TTC1' - 0" = Select the R5 clock for the APB interface of TTC1*/ -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL_DEFVAL -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL_SHIFT -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL_MASK -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL_SHIFT 2 -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC1_SEL_MASK 0x0000000CU - -/*00" = Select the APB switch clock for the APB interface of TTC2'01" = Select the PLL ref clock for the APB interface of TTC2' - 0" = Select the R5 clock for the APB interface of TTC2*/ -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL_DEFVAL -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL_SHIFT -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL_MASK -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL_SHIFT 4 -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC2_SEL_MASK 0x00000030U - -/*00" = Select the APB switch clock for the APB interface of TTC3'01" = Select the PLL ref clock for the APB interface of TTC3' - 0" = Select the R5 clock for the APB interface of TTC3*/ -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL_DEFVAL -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL_SHIFT -#undef IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL_MASK -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL_SHIFT 6 -#define IOU_SLCR_IOU_TTC_APB_CLK_TTC3_SEL_MASK 0x000000C0U - -/*System watchdog timer clock source selection: 0: Internal APB clock 1: External (PL clock via EMIO or Pinout clock via MIO)*/ -#undef FPD_SLCR_WDT_CLK_SEL_SELECT_DEFVAL -#undef FPD_SLCR_WDT_CLK_SEL_SELECT_SHIFT -#undef FPD_SLCR_WDT_CLK_SEL_SELECT_MASK -#define FPD_SLCR_WDT_CLK_SEL_SELECT_DEFVAL 0x00000000 -#define FPD_SLCR_WDT_CLK_SEL_SELECT_SHIFT 0 -#define FPD_SLCR_WDT_CLK_SEL_SELECT_MASK 0x00000001U - -/*System watchdog timer clock source selection: 0: internal clock APB clock 1: external clock from PL via EMIO, or from pinout - ia MIO*/ -#undef IOU_SLCR_WDT_CLK_SEL_SELECT_DEFVAL -#undef IOU_SLCR_WDT_CLK_SEL_SELECT_SHIFT -#undef IOU_SLCR_WDT_CLK_SEL_SELECT_MASK -#define IOU_SLCR_WDT_CLK_SEL_SELECT_DEFVAL 0x00000000 -#define IOU_SLCR_WDT_CLK_SEL_SELECT_SHIFT 0 -#define IOU_SLCR_WDT_CLK_SEL_SELECT_MASK 0x00000001U - -/*System watchdog timer clock source selection: 0: internal clock APB clock 1: external clock pss_ref_clk*/ -#undef LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT_DEFVAL -#undef LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT_SHIFT -#undef LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT_MASK -#define LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT_DEFVAL 0x00000000 -#define LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT_SHIFT 0 -#define LPD_SLCR_CSUPMU_WDT_CLK_SEL_SELECT_MASK 0x00000001U -#undef CRF_APB_RST_DDR_SS_OFFSET -#define CRF_APB_RST_DDR_SS_OFFSET 0XFD1A0108 -#undef DDRC_MSTR_OFFSET -#define DDRC_MSTR_OFFSET 0XFD070000 -#undef DDRC_MRCTRL0_OFFSET -#define DDRC_MRCTRL0_OFFSET 0XFD070010 -#undef DDRC_DERATEEN_OFFSET -#define DDRC_DERATEEN_OFFSET 0XFD070020 -#undef DDRC_DERATEINT_OFFSET -#define DDRC_DERATEINT_OFFSET 0XFD070024 -#undef DDRC_PWRCTL_OFFSET -#define DDRC_PWRCTL_OFFSET 0XFD070030 -#undef DDRC_PWRTMG_OFFSET -#define DDRC_PWRTMG_OFFSET 0XFD070034 -#undef DDRC_RFSHCTL0_OFFSET -#define DDRC_RFSHCTL0_OFFSET 0XFD070050 -#undef DDRC_RFSHCTL3_OFFSET -#define DDRC_RFSHCTL3_OFFSET 0XFD070060 -#undef DDRC_RFSHTMG_OFFSET -#define DDRC_RFSHTMG_OFFSET 0XFD070064 -#undef DDRC_ECCCFG0_OFFSET -#define DDRC_ECCCFG0_OFFSET 0XFD070070 -#undef DDRC_ECCCFG1_OFFSET -#define DDRC_ECCCFG1_OFFSET 0XFD070074 -#undef DDRC_CRCPARCTL1_OFFSET -#define DDRC_CRCPARCTL1_OFFSET 0XFD0700C4 -#undef DDRC_CRCPARCTL2_OFFSET -#define DDRC_CRCPARCTL2_OFFSET 0XFD0700C8 -#undef DDRC_INIT0_OFFSET -#define DDRC_INIT0_OFFSET 0XFD0700D0 -#undef DDRC_INIT1_OFFSET -#define DDRC_INIT1_OFFSET 0XFD0700D4 -#undef DDRC_INIT2_OFFSET -#define DDRC_INIT2_OFFSET 0XFD0700D8 -#undef DDRC_INIT3_OFFSET -#define DDRC_INIT3_OFFSET 0XFD0700DC -#undef DDRC_INIT4_OFFSET -#define DDRC_INIT4_OFFSET 0XFD0700E0 -#undef DDRC_INIT5_OFFSET -#define DDRC_INIT5_OFFSET 0XFD0700E4 -#undef DDRC_INIT6_OFFSET -#define DDRC_INIT6_OFFSET 0XFD0700E8 -#undef DDRC_INIT7_OFFSET -#define DDRC_INIT7_OFFSET 0XFD0700EC -#undef DDRC_DIMMCTL_OFFSET -#define DDRC_DIMMCTL_OFFSET 0XFD0700F0 -#undef DDRC_RANKCTL_OFFSET -#define DDRC_RANKCTL_OFFSET 0XFD0700F4 -#undef DDRC_DRAMTMG0_OFFSET -#define DDRC_DRAMTMG0_OFFSET 0XFD070100 -#undef DDRC_DRAMTMG1_OFFSET -#define DDRC_DRAMTMG1_OFFSET 0XFD070104 -#undef DDRC_DRAMTMG2_OFFSET -#define DDRC_DRAMTMG2_OFFSET 0XFD070108 -#undef DDRC_DRAMTMG3_OFFSET -#define DDRC_DRAMTMG3_OFFSET 0XFD07010C -#undef DDRC_DRAMTMG4_OFFSET -#define DDRC_DRAMTMG4_OFFSET 0XFD070110 -#undef DDRC_DRAMTMG5_OFFSET -#define DDRC_DRAMTMG5_OFFSET 0XFD070114 -#undef DDRC_DRAMTMG6_OFFSET -#define DDRC_DRAMTMG6_OFFSET 0XFD070118 -#undef DDRC_DRAMTMG7_OFFSET -#define DDRC_DRAMTMG7_OFFSET 0XFD07011C -#undef DDRC_DRAMTMG8_OFFSET -#define DDRC_DRAMTMG8_OFFSET 0XFD070120 -#undef DDRC_DRAMTMG9_OFFSET -#define DDRC_DRAMTMG9_OFFSET 0XFD070124 -#undef DDRC_DRAMTMG11_OFFSET -#define DDRC_DRAMTMG11_OFFSET 0XFD07012C -#undef DDRC_DRAMTMG12_OFFSET -#define DDRC_DRAMTMG12_OFFSET 0XFD070130 -#undef DDRC_ZQCTL0_OFFSET -#define DDRC_ZQCTL0_OFFSET 0XFD070180 -#undef DDRC_ZQCTL1_OFFSET -#define DDRC_ZQCTL1_OFFSET 0XFD070184 -#undef DDRC_DFITMG0_OFFSET -#define DDRC_DFITMG0_OFFSET 0XFD070190 -#undef DDRC_DFITMG1_OFFSET -#define DDRC_DFITMG1_OFFSET 0XFD070194 -#undef DDRC_DFILPCFG0_OFFSET -#define DDRC_DFILPCFG0_OFFSET 0XFD070198 -#undef DDRC_DFILPCFG1_OFFSET -#define DDRC_DFILPCFG1_OFFSET 0XFD07019C -#undef DDRC_DFIUPD1_OFFSET -#define DDRC_DFIUPD1_OFFSET 0XFD0701A4 -#undef DDRC_DFIMISC_OFFSET -#define DDRC_DFIMISC_OFFSET 0XFD0701B0 -#undef DDRC_DFITMG2_OFFSET -#define DDRC_DFITMG2_OFFSET 0XFD0701B4 -#undef DDRC_DBICTL_OFFSET -#define DDRC_DBICTL_OFFSET 0XFD0701C0 -#undef DDRC_ADDRMAP0_OFFSET -#define DDRC_ADDRMAP0_OFFSET 0XFD070200 -#undef DDRC_ADDRMAP1_OFFSET -#define DDRC_ADDRMAP1_OFFSET 0XFD070204 -#undef DDRC_ADDRMAP2_OFFSET -#define DDRC_ADDRMAP2_OFFSET 0XFD070208 -#undef DDRC_ADDRMAP3_OFFSET -#define DDRC_ADDRMAP3_OFFSET 0XFD07020C -#undef DDRC_ADDRMAP4_OFFSET -#define DDRC_ADDRMAP4_OFFSET 0XFD070210 -#undef DDRC_ADDRMAP5_OFFSET -#define DDRC_ADDRMAP5_OFFSET 0XFD070214 -#undef DDRC_ADDRMAP6_OFFSET -#define DDRC_ADDRMAP6_OFFSET 0XFD070218 -#undef DDRC_ADDRMAP7_OFFSET -#define DDRC_ADDRMAP7_OFFSET 0XFD07021C -#undef DDRC_ADDRMAP8_OFFSET -#define DDRC_ADDRMAP8_OFFSET 0XFD070220 -#undef DDRC_ADDRMAP9_OFFSET -#define DDRC_ADDRMAP9_OFFSET 0XFD070224 -#undef DDRC_ADDRMAP10_OFFSET -#define DDRC_ADDRMAP10_OFFSET 0XFD070228 -#undef DDRC_ADDRMAP11_OFFSET -#define DDRC_ADDRMAP11_OFFSET 0XFD07022C -#undef DDRC_ODTCFG_OFFSET -#define DDRC_ODTCFG_OFFSET 0XFD070240 -#undef DDRC_ODTMAP_OFFSET -#define DDRC_ODTMAP_OFFSET 0XFD070244 -#undef DDRC_SCHED_OFFSET -#define DDRC_SCHED_OFFSET 0XFD070250 -#undef DDRC_PERFLPR1_OFFSET -#define DDRC_PERFLPR1_OFFSET 0XFD070264 -#undef DDRC_PERFWR1_OFFSET -#define DDRC_PERFWR1_OFFSET 0XFD07026C -#undef DDRC_DQMAP5_OFFSET -#define DDRC_DQMAP5_OFFSET 0XFD070294 -#undef DDRC_DBG0_OFFSET -#define DDRC_DBG0_OFFSET 0XFD070300 -#undef DDRC_DBGCMD_OFFSET -#define DDRC_DBGCMD_OFFSET 0XFD07030C -#undef DDRC_SWCTL_OFFSET -#define DDRC_SWCTL_OFFSET 0XFD070320 -#undef DDRC_PCCFG_OFFSET -#define DDRC_PCCFG_OFFSET 0XFD070400 -#undef DDRC_PCFGR_0_OFFSET -#define DDRC_PCFGR_0_OFFSET 0XFD070404 -#undef DDRC_PCFGW_0_OFFSET -#define DDRC_PCFGW_0_OFFSET 0XFD070408 -#undef DDRC_PCTRL_0_OFFSET -#define DDRC_PCTRL_0_OFFSET 0XFD070490 -#undef DDRC_PCFGQOS0_0_OFFSET -#define DDRC_PCFGQOS0_0_OFFSET 0XFD070494 -#undef DDRC_PCFGQOS1_0_OFFSET -#define DDRC_PCFGQOS1_0_OFFSET 0XFD070498 -#undef DDRC_PCFGR_1_OFFSET -#define DDRC_PCFGR_1_OFFSET 0XFD0704B4 -#undef DDRC_PCFGW_1_OFFSET -#define DDRC_PCFGW_1_OFFSET 0XFD0704B8 -#undef DDRC_PCTRL_1_OFFSET -#define DDRC_PCTRL_1_OFFSET 0XFD070540 -#undef DDRC_PCFGQOS0_1_OFFSET -#define DDRC_PCFGQOS0_1_OFFSET 0XFD070544 -#undef DDRC_PCFGQOS1_1_OFFSET -#define DDRC_PCFGQOS1_1_OFFSET 0XFD070548 -#undef DDRC_PCFGR_2_OFFSET -#define DDRC_PCFGR_2_OFFSET 0XFD070564 -#undef DDRC_PCFGW_2_OFFSET -#define DDRC_PCFGW_2_OFFSET 0XFD070568 -#undef DDRC_PCTRL_2_OFFSET -#define DDRC_PCTRL_2_OFFSET 0XFD0705F0 -#undef DDRC_PCFGQOS0_2_OFFSET -#define DDRC_PCFGQOS0_2_OFFSET 0XFD0705F4 -#undef DDRC_PCFGQOS1_2_OFFSET -#define DDRC_PCFGQOS1_2_OFFSET 0XFD0705F8 -#undef DDRC_PCFGR_3_OFFSET -#define DDRC_PCFGR_3_OFFSET 0XFD070614 -#undef DDRC_PCFGW_3_OFFSET -#define DDRC_PCFGW_3_OFFSET 0XFD070618 -#undef DDRC_PCTRL_3_OFFSET -#define DDRC_PCTRL_3_OFFSET 0XFD0706A0 -#undef DDRC_PCFGQOS0_3_OFFSET -#define DDRC_PCFGQOS0_3_OFFSET 0XFD0706A4 -#undef DDRC_PCFGQOS1_3_OFFSET -#define DDRC_PCFGQOS1_3_OFFSET 0XFD0706A8 -#undef DDRC_PCFGWQOS0_3_OFFSET -#define DDRC_PCFGWQOS0_3_OFFSET 0XFD0706AC -#undef DDRC_PCFGWQOS1_3_OFFSET -#define DDRC_PCFGWQOS1_3_OFFSET 0XFD0706B0 -#undef DDRC_PCFGR_4_OFFSET -#define DDRC_PCFGR_4_OFFSET 0XFD0706C4 -#undef DDRC_PCFGW_4_OFFSET -#define DDRC_PCFGW_4_OFFSET 0XFD0706C8 -#undef DDRC_PCTRL_4_OFFSET -#define DDRC_PCTRL_4_OFFSET 0XFD070750 -#undef DDRC_PCFGQOS0_4_OFFSET -#define DDRC_PCFGQOS0_4_OFFSET 0XFD070754 -#undef DDRC_PCFGQOS1_4_OFFSET -#define DDRC_PCFGQOS1_4_OFFSET 0XFD070758 -#undef DDRC_PCFGWQOS0_4_OFFSET -#define DDRC_PCFGWQOS0_4_OFFSET 0XFD07075C -#undef DDRC_PCFGWQOS1_4_OFFSET -#define DDRC_PCFGWQOS1_4_OFFSET 0XFD070760 -#undef DDRC_PCFGR_5_OFFSET -#define DDRC_PCFGR_5_OFFSET 0XFD070774 -#undef DDRC_PCFGW_5_OFFSET -#define DDRC_PCFGW_5_OFFSET 0XFD070778 -#undef DDRC_PCTRL_5_OFFSET -#define DDRC_PCTRL_5_OFFSET 0XFD070800 -#undef DDRC_PCFGQOS0_5_OFFSET -#define DDRC_PCFGQOS0_5_OFFSET 0XFD070804 -#undef DDRC_PCFGQOS1_5_OFFSET -#define DDRC_PCFGQOS1_5_OFFSET 0XFD070808 -#undef DDRC_PCFGWQOS0_5_OFFSET -#define DDRC_PCFGWQOS0_5_OFFSET 0XFD07080C -#undef DDRC_PCFGWQOS1_5_OFFSET -#define DDRC_PCFGWQOS1_5_OFFSET 0XFD070810 -#undef DDRC_SARBASE0_OFFSET -#define DDRC_SARBASE0_OFFSET 0XFD070F04 -#undef DDRC_SARSIZE0_OFFSET -#define DDRC_SARSIZE0_OFFSET 0XFD070F08 -#undef DDRC_SARBASE1_OFFSET -#define DDRC_SARBASE1_OFFSET 0XFD070F0C -#undef DDRC_SARSIZE1_OFFSET -#define DDRC_SARSIZE1_OFFSET 0XFD070F10 -#undef DDRC_DFITMG0_SHADOW_OFFSET -#define DDRC_DFITMG0_SHADOW_OFFSET 0XFD072190 -#undef CRF_APB_RST_DDR_SS_OFFSET -#define CRF_APB_RST_DDR_SS_OFFSET 0XFD1A0108 -#undef DDR_PHY_PGCR0_OFFSET -#define DDR_PHY_PGCR0_OFFSET 0XFD080010 -#undef DDR_PHY_PGCR2_OFFSET -#define DDR_PHY_PGCR2_OFFSET 0XFD080018 -#undef DDR_PHY_PGCR3_OFFSET -#define DDR_PHY_PGCR3_OFFSET 0XFD08001C -#undef DDR_PHY_PGCR5_OFFSET -#define DDR_PHY_PGCR5_OFFSET 0XFD080024 -#undef DDR_PHY_PTR0_OFFSET -#define DDR_PHY_PTR0_OFFSET 0XFD080040 -#undef DDR_PHY_PTR1_OFFSET -#define DDR_PHY_PTR1_OFFSET 0XFD080044 -#undef DDR_PHY_DSGCR_OFFSET -#define DDR_PHY_DSGCR_OFFSET 0XFD080090 -#undef DDR_PHY_DCR_OFFSET -#define DDR_PHY_DCR_OFFSET 0XFD080100 -#undef DDR_PHY_DTPR0_OFFSET -#define DDR_PHY_DTPR0_OFFSET 0XFD080110 -#undef DDR_PHY_DTPR1_OFFSET -#define DDR_PHY_DTPR1_OFFSET 0XFD080114 -#undef DDR_PHY_DTPR2_OFFSET -#define DDR_PHY_DTPR2_OFFSET 0XFD080118 -#undef DDR_PHY_DTPR3_OFFSET -#define DDR_PHY_DTPR3_OFFSET 0XFD08011C -#undef DDR_PHY_DTPR4_OFFSET -#define DDR_PHY_DTPR4_OFFSET 0XFD080120 -#undef DDR_PHY_DTPR5_OFFSET -#define DDR_PHY_DTPR5_OFFSET 0XFD080124 -#undef DDR_PHY_DTPR6_OFFSET -#define DDR_PHY_DTPR6_OFFSET 0XFD080128 -#undef DDR_PHY_RDIMMGCR0_OFFSET -#define DDR_PHY_RDIMMGCR0_OFFSET 0XFD080140 -#undef DDR_PHY_RDIMMGCR1_OFFSET -#define DDR_PHY_RDIMMGCR1_OFFSET 0XFD080144 -#undef DDR_PHY_RDIMMCR0_OFFSET -#define DDR_PHY_RDIMMCR0_OFFSET 0XFD080150 -#undef DDR_PHY_RDIMMCR1_OFFSET -#define DDR_PHY_RDIMMCR1_OFFSET 0XFD080154 -#undef DDR_PHY_MR0_OFFSET -#define DDR_PHY_MR0_OFFSET 0XFD080180 -#undef DDR_PHY_MR1_OFFSET -#define DDR_PHY_MR1_OFFSET 0XFD080184 -#undef DDR_PHY_MR2_OFFSET -#define DDR_PHY_MR2_OFFSET 0XFD080188 -#undef DDR_PHY_MR3_OFFSET -#define DDR_PHY_MR3_OFFSET 0XFD08018C -#undef DDR_PHY_MR4_OFFSET -#define DDR_PHY_MR4_OFFSET 0XFD080190 -#undef DDR_PHY_MR5_OFFSET -#define DDR_PHY_MR5_OFFSET 0XFD080194 -#undef DDR_PHY_MR6_OFFSET -#define DDR_PHY_MR6_OFFSET 0XFD080198 -#undef DDR_PHY_MR11_OFFSET -#define DDR_PHY_MR11_OFFSET 0XFD0801AC -#undef DDR_PHY_MR12_OFFSET -#define DDR_PHY_MR12_OFFSET 0XFD0801B0 -#undef DDR_PHY_MR13_OFFSET -#define DDR_PHY_MR13_OFFSET 0XFD0801B4 -#undef DDR_PHY_MR14_OFFSET -#define DDR_PHY_MR14_OFFSET 0XFD0801B8 -#undef DDR_PHY_MR22_OFFSET -#define DDR_PHY_MR22_OFFSET 0XFD0801D8 -#undef DDR_PHY_DTCR0_OFFSET -#define DDR_PHY_DTCR0_OFFSET 0XFD080200 -#undef DDR_PHY_DTCR1_OFFSET -#define DDR_PHY_DTCR1_OFFSET 0XFD080204 -#undef DDR_PHY_CATR0_OFFSET -#define DDR_PHY_CATR0_OFFSET 0XFD080240 -#undef DDR_PHY_BISTLSR_OFFSET -#define DDR_PHY_BISTLSR_OFFSET 0XFD080414 -#undef DDR_PHY_RIOCR5_OFFSET -#define DDR_PHY_RIOCR5_OFFSET 0XFD0804F4 -#undef DDR_PHY_ACIOCR0_OFFSET -#define DDR_PHY_ACIOCR0_OFFSET 0XFD080500 -#undef DDR_PHY_ACIOCR2_OFFSET -#define DDR_PHY_ACIOCR2_OFFSET 0XFD080508 -#undef DDR_PHY_ACIOCR3_OFFSET -#define DDR_PHY_ACIOCR3_OFFSET 0XFD08050C -#undef DDR_PHY_ACIOCR4_OFFSET -#define DDR_PHY_ACIOCR4_OFFSET 0XFD080510 -#undef DDR_PHY_IOVCR0_OFFSET -#define DDR_PHY_IOVCR0_OFFSET 0XFD080520 -#undef DDR_PHY_VTCR0_OFFSET -#define DDR_PHY_VTCR0_OFFSET 0XFD080528 -#undef DDR_PHY_VTCR1_OFFSET -#define DDR_PHY_VTCR1_OFFSET 0XFD08052C -#undef DDR_PHY_ACBDLR1_OFFSET -#define DDR_PHY_ACBDLR1_OFFSET 0XFD080544 -#undef DDR_PHY_ACBDLR2_OFFSET -#define DDR_PHY_ACBDLR2_OFFSET 0XFD080548 -#undef DDR_PHY_ACBDLR6_OFFSET -#define DDR_PHY_ACBDLR6_OFFSET 0XFD080558 -#undef DDR_PHY_ACBDLR7_OFFSET -#define DDR_PHY_ACBDLR7_OFFSET 0XFD08055C -#undef DDR_PHY_ACBDLR8_OFFSET -#define DDR_PHY_ACBDLR8_OFFSET 0XFD080560 -#undef DDR_PHY_ACBDLR9_OFFSET -#define DDR_PHY_ACBDLR9_OFFSET 0XFD080564 -#undef DDR_PHY_ZQCR_OFFSET -#define DDR_PHY_ZQCR_OFFSET 0XFD080680 -#undef DDR_PHY_ZQ0PR0_OFFSET -#define DDR_PHY_ZQ0PR0_OFFSET 0XFD080684 -#undef DDR_PHY_ZQ0OR0_OFFSET -#define DDR_PHY_ZQ0OR0_OFFSET 0XFD080694 -#undef DDR_PHY_ZQ0OR1_OFFSET -#define DDR_PHY_ZQ0OR1_OFFSET 0XFD080698 -#undef DDR_PHY_ZQ1PR0_OFFSET -#define DDR_PHY_ZQ1PR0_OFFSET 0XFD0806A4 -#undef DDR_PHY_DX0GCR0_OFFSET -#define DDR_PHY_DX0GCR0_OFFSET 0XFD080700 -#undef DDR_PHY_DX0GCR4_OFFSET -#define DDR_PHY_DX0GCR4_OFFSET 0XFD080710 -#undef DDR_PHY_DX0GCR5_OFFSET -#define DDR_PHY_DX0GCR5_OFFSET 0XFD080714 -#undef DDR_PHY_DX0GCR6_OFFSET -#define DDR_PHY_DX0GCR6_OFFSET 0XFD080718 -#undef DDR_PHY_DX0LCDLR2_OFFSET -#define DDR_PHY_DX0LCDLR2_OFFSET 0XFD080788 -#undef DDR_PHY_DX0GTR0_OFFSET -#define DDR_PHY_DX0GTR0_OFFSET 0XFD0807C0 -#undef DDR_PHY_DX1GCR0_OFFSET -#define DDR_PHY_DX1GCR0_OFFSET 0XFD080800 -#undef DDR_PHY_DX1GCR4_OFFSET -#define DDR_PHY_DX1GCR4_OFFSET 0XFD080810 -#undef DDR_PHY_DX1GCR5_OFFSET -#define DDR_PHY_DX1GCR5_OFFSET 0XFD080814 -#undef DDR_PHY_DX1GCR6_OFFSET -#define DDR_PHY_DX1GCR6_OFFSET 0XFD080818 -#undef DDR_PHY_DX1LCDLR2_OFFSET -#define DDR_PHY_DX1LCDLR2_OFFSET 0XFD080888 -#undef DDR_PHY_DX1GTR0_OFFSET -#define DDR_PHY_DX1GTR0_OFFSET 0XFD0808C0 -#undef DDR_PHY_DX2GCR0_OFFSET -#define DDR_PHY_DX2GCR0_OFFSET 0XFD080900 -#undef DDR_PHY_DX2GCR1_OFFSET -#define DDR_PHY_DX2GCR1_OFFSET 0XFD080904 -#undef DDR_PHY_DX2GCR4_OFFSET -#define DDR_PHY_DX2GCR4_OFFSET 0XFD080910 -#undef DDR_PHY_DX2GCR5_OFFSET -#define DDR_PHY_DX2GCR5_OFFSET 0XFD080914 -#undef DDR_PHY_DX2GCR6_OFFSET -#define DDR_PHY_DX2GCR6_OFFSET 0XFD080918 -#undef DDR_PHY_DX2LCDLR2_OFFSET -#define DDR_PHY_DX2LCDLR2_OFFSET 0XFD080988 -#undef DDR_PHY_DX2GTR0_OFFSET -#define DDR_PHY_DX2GTR0_OFFSET 0XFD0809C0 -#undef DDR_PHY_DX3GCR0_OFFSET -#define DDR_PHY_DX3GCR0_OFFSET 0XFD080A00 -#undef DDR_PHY_DX3GCR1_OFFSET -#define DDR_PHY_DX3GCR1_OFFSET 0XFD080A04 -#undef DDR_PHY_DX3GCR4_OFFSET -#define DDR_PHY_DX3GCR4_OFFSET 0XFD080A10 -#undef DDR_PHY_DX3GCR5_OFFSET -#define DDR_PHY_DX3GCR5_OFFSET 0XFD080A14 -#undef DDR_PHY_DX3GCR6_OFFSET -#define DDR_PHY_DX3GCR6_OFFSET 0XFD080A18 -#undef DDR_PHY_DX3LCDLR2_OFFSET -#define DDR_PHY_DX3LCDLR2_OFFSET 0XFD080A88 -#undef DDR_PHY_DX3GTR0_OFFSET -#define DDR_PHY_DX3GTR0_OFFSET 0XFD080AC0 -#undef DDR_PHY_DX4GCR0_OFFSET -#define DDR_PHY_DX4GCR0_OFFSET 0XFD080B00 -#undef DDR_PHY_DX4GCR1_OFFSET -#define DDR_PHY_DX4GCR1_OFFSET 0XFD080B04 -#undef DDR_PHY_DX4GCR4_OFFSET -#define DDR_PHY_DX4GCR4_OFFSET 0XFD080B10 -#undef DDR_PHY_DX4GCR5_OFFSET -#define DDR_PHY_DX4GCR5_OFFSET 0XFD080B14 -#undef DDR_PHY_DX4GCR6_OFFSET -#define DDR_PHY_DX4GCR6_OFFSET 0XFD080B18 -#undef DDR_PHY_DX4LCDLR2_OFFSET -#define DDR_PHY_DX4LCDLR2_OFFSET 0XFD080B88 -#undef DDR_PHY_DX4GTR0_OFFSET -#define DDR_PHY_DX4GTR0_OFFSET 0XFD080BC0 -#undef DDR_PHY_DX5GCR0_OFFSET -#define DDR_PHY_DX5GCR0_OFFSET 0XFD080C00 -#undef DDR_PHY_DX5GCR1_OFFSET -#define DDR_PHY_DX5GCR1_OFFSET 0XFD080C04 -#undef DDR_PHY_DX5GCR4_OFFSET -#define DDR_PHY_DX5GCR4_OFFSET 0XFD080C10 -#undef DDR_PHY_DX5GCR5_OFFSET -#define DDR_PHY_DX5GCR5_OFFSET 0XFD080C14 -#undef DDR_PHY_DX5GCR6_OFFSET -#define DDR_PHY_DX5GCR6_OFFSET 0XFD080C18 -#undef DDR_PHY_DX5LCDLR2_OFFSET -#define DDR_PHY_DX5LCDLR2_OFFSET 0XFD080C88 -#undef DDR_PHY_DX5GTR0_OFFSET -#define DDR_PHY_DX5GTR0_OFFSET 0XFD080CC0 -#undef DDR_PHY_DX6GCR0_OFFSET -#define DDR_PHY_DX6GCR0_OFFSET 0XFD080D00 -#undef DDR_PHY_DX6GCR1_OFFSET -#define DDR_PHY_DX6GCR1_OFFSET 0XFD080D04 -#undef DDR_PHY_DX6GCR4_OFFSET -#define DDR_PHY_DX6GCR4_OFFSET 0XFD080D10 -#undef DDR_PHY_DX6GCR5_OFFSET -#define DDR_PHY_DX6GCR5_OFFSET 0XFD080D14 -#undef DDR_PHY_DX6GCR6_OFFSET -#define DDR_PHY_DX6GCR6_OFFSET 0XFD080D18 -#undef DDR_PHY_DX6LCDLR2_OFFSET -#define DDR_PHY_DX6LCDLR2_OFFSET 0XFD080D88 -#undef DDR_PHY_DX6GTR0_OFFSET -#define DDR_PHY_DX6GTR0_OFFSET 0XFD080DC0 -#undef DDR_PHY_DX7GCR0_OFFSET -#define DDR_PHY_DX7GCR0_OFFSET 0XFD080E00 -#undef DDR_PHY_DX7GCR1_OFFSET -#define DDR_PHY_DX7GCR1_OFFSET 0XFD080E04 -#undef DDR_PHY_DX7GCR4_OFFSET -#define DDR_PHY_DX7GCR4_OFFSET 0XFD080E10 -#undef DDR_PHY_DX7GCR5_OFFSET -#define DDR_PHY_DX7GCR5_OFFSET 0XFD080E14 -#undef DDR_PHY_DX7GCR6_OFFSET -#define DDR_PHY_DX7GCR6_OFFSET 0XFD080E18 -#undef DDR_PHY_DX7LCDLR2_OFFSET -#define DDR_PHY_DX7LCDLR2_OFFSET 0XFD080E88 -#undef DDR_PHY_DX7GTR0_OFFSET -#define DDR_PHY_DX7GTR0_OFFSET 0XFD080EC0 -#undef DDR_PHY_DX8GCR0_OFFSET -#define DDR_PHY_DX8GCR0_OFFSET 0XFD080F00 -#undef DDR_PHY_DX8GCR1_OFFSET -#define DDR_PHY_DX8GCR1_OFFSET 0XFD080F04 -#undef DDR_PHY_DX8GCR4_OFFSET -#define DDR_PHY_DX8GCR4_OFFSET 0XFD080F10 -#undef DDR_PHY_DX8GCR5_OFFSET -#define DDR_PHY_DX8GCR5_OFFSET 0XFD080F14 -#undef DDR_PHY_DX8GCR6_OFFSET -#define DDR_PHY_DX8GCR6_OFFSET 0XFD080F18 -#undef DDR_PHY_DX8LCDLR2_OFFSET -#define DDR_PHY_DX8LCDLR2_OFFSET 0XFD080F88 -#undef DDR_PHY_DX8GTR0_OFFSET -#define DDR_PHY_DX8GTR0_OFFSET 0XFD080FC0 -#undef DDR_PHY_DX8SL0OSC_OFFSET -#define DDR_PHY_DX8SL0OSC_OFFSET 0XFD081400 -#undef DDR_PHY_DX8SL0DQSCTL_OFFSET -#define DDR_PHY_DX8SL0DQSCTL_OFFSET 0XFD08141C -#undef DDR_PHY_DX8SL0DXCTL2_OFFSET -#define DDR_PHY_DX8SL0DXCTL2_OFFSET 0XFD08142C -#undef DDR_PHY_DX8SL0IOCR_OFFSET -#define DDR_PHY_DX8SL0IOCR_OFFSET 0XFD081430 -#undef DDR_PHY_DX8SL1OSC_OFFSET -#define DDR_PHY_DX8SL1OSC_OFFSET 0XFD081440 -#undef DDR_PHY_DX8SL1DQSCTL_OFFSET -#define DDR_PHY_DX8SL1DQSCTL_OFFSET 0XFD08145C -#undef DDR_PHY_DX8SL1DXCTL2_OFFSET -#define DDR_PHY_DX8SL1DXCTL2_OFFSET 0XFD08146C -#undef DDR_PHY_DX8SL1IOCR_OFFSET -#define DDR_PHY_DX8SL1IOCR_OFFSET 0XFD081470 -#undef DDR_PHY_DX8SL2OSC_OFFSET -#define DDR_PHY_DX8SL2OSC_OFFSET 0XFD081480 -#undef DDR_PHY_DX8SL2DQSCTL_OFFSET -#define DDR_PHY_DX8SL2DQSCTL_OFFSET 0XFD08149C -#undef DDR_PHY_DX8SL2DXCTL2_OFFSET -#define DDR_PHY_DX8SL2DXCTL2_OFFSET 0XFD0814AC -#undef DDR_PHY_DX8SL2IOCR_OFFSET -#define DDR_PHY_DX8SL2IOCR_OFFSET 0XFD0814B0 -#undef DDR_PHY_DX8SL3OSC_OFFSET -#define DDR_PHY_DX8SL3OSC_OFFSET 0XFD0814C0 -#undef DDR_PHY_DX8SL3DQSCTL_OFFSET -#define DDR_PHY_DX8SL3DQSCTL_OFFSET 0XFD0814DC -#undef DDR_PHY_DX8SL3DXCTL2_OFFSET -#define DDR_PHY_DX8SL3DXCTL2_OFFSET 0XFD0814EC -#undef DDR_PHY_DX8SL3IOCR_OFFSET -#define DDR_PHY_DX8SL3IOCR_OFFSET 0XFD0814F0 -#undef DDR_PHY_DX8SL4OSC_OFFSET -#define DDR_PHY_DX8SL4OSC_OFFSET 0XFD081500 -#undef DDR_PHY_DX8SL4DQSCTL_OFFSET -#define DDR_PHY_DX8SL4DQSCTL_OFFSET 0XFD08151C -#undef DDR_PHY_DX8SL4DXCTL2_OFFSET -#define DDR_PHY_DX8SL4DXCTL2_OFFSET 0XFD08152C -#undef DDR_PHY_DX8SL4IOCR_OFFSET -#define DDR_PHY_DX8SL4IOCR_OFFSET 0XFD081530 -#undef DDR_PHY_DX8SLBDQSCTL_OFFSET -#define DDR_PHY_DX8SLBDQSCTL_OFFSET 0XFD0817DC -#undef DDR_PHY_PIR_OFFSET -#define DDR_PHY_PIR_OFFSET 0XFD080004 - -/*DDR block level reset inside of the DDR Sub System*/ -#undef CRF_APB_RST_DDR_SS_DDR_RESET_DEFVAL -#undef CRF_APB_RST_DDR_SS_DDR_RESET_SHIFT -#undef CRF_APB_RST_DDR_SS_DDR_RESET_MASK -#define CRF_APB_RST_DDR_SS_DDR_RESET_DEFVAL 0x0000000F -#define CRF_APB_RST_DDR_SS_DDR_RESET_SHIFT 3 -#define CRF_APB_RST_DDR_SS_DDR_RESET_MASK 0x00000008U - -/*Indicates the configuration of the device used in the system. - 00 - x4 device - 01 - x8 device - 10 - x16 device - 11 - x32 - evice*/ -#undef DDRC_MSTR_DEVICE_CONFIG_DEFVAL -#undef DDRC_MSTR_DEVICE_CONFIG_SHIFT -#undef DDRC_MSTR_DEVICE_CONFIG_MASK -#define DDRC_MSTR_DEVICE_CONFIG_DEFVAL 0x03040001 -#define DDRC_MSTR_DEVICE_CONFIG_SHIFT 30 -#define DDRC_MSTR_DEVICE_CONFIG_MASK 0xC0000000U - -/*Choose which registers are used. - 0 - Original registers - 1 - Shadow registers*/ -#undef DDRC_MSTR_FREQUENCY_MODE_DEFVAL -#undef DDRC_MSTR_FREQUENCY_MODE_SHIFT -#undef DDRC_MSTR_FREQUENCY_MODE_MASK -#define DDRC_MSTR_FREQUENCY_MODE_DEFVAL 0x03040001 -#define DDRC_MSTR_FREQUENCY_MODE_SHIFT 29 -#define DDRC_MSTR_FREQUENCY_MODE_MASK 0x20000000U - -/*Only present for multi-rank configurations. Each bit represents one rank. For two-rank configurations, only bits[25:24] are p - esent. - 1 - populated - 0 - unpopulated LSB is the lowest rank number. For 2 ranks following combinations are legal: - 01 - - ne rank - 11 - Two ranks - Others - Reserved. For 4 ranks following combinations are legal: - 0001 - One rank - 0011 - Two ra - ks - 1111 - Four ranks*/ -#undef DDRC_MSTR_ACTIVE_RANKS_DEFVAL -#undef DDRC_MSTR_ACTIVE_RANKS_SHIFT -#undef DDRC_MSTR_ACTIVE_RANKS_MASK -#define DDRC_MSTR_ACTIVE_RANKS_DEFVAL 0x03040001 -#define DDRC_MSTR_ACTIVE_RANKS_SHIFT 24 -#define DDRC_MSTR_ACTIVE_RANKS_MASK 0x03000000U - -/*SDRAM burst length used: - 0001 - Burst length of 2 (only supported for mDDR) - 0010 - Burst length of 4 - 0100 - Burst lengt - of 8 - 1000 - Burst length of 16 (only supported for mDDR, LPDDR2, and LPDDR4) All other values are reserved. This controls - he burst size used to access the SDRAM. This must match the burst length mode register setting in the SDRAM. (For BC4/8 on-th - -fly mode of DDR3 and DDR4, set this field to 0x0100) Burst length of 2 is not supported with AXI ports when MEMC_BURST_LENGT - is 8. Burst length of 2 is only supported with MEMC_FREQ_RATIO = 1*/ -#undef DDRC_MSTR_BURST_RDWR_DEFVAL -#undef DDRC_MSTR_BURST_RDWR_SHIFT -#undef DDRC_MSTR_BURST_RDWR_MASK -#define DDRC_MSTR_BURST_RDWR_DEFVAL 0x03040001 -#define DDRC_MSTR_BURST_RDWR_SHIFT 16 -#define DDRC_MSTR_BURST_RDWR_MASK 0x000F0000U - -/*Set to 1 when the uMCTL2 and DRAM has to be put in DLL-off mode for low frequency operation. Set to 0 to put uMCTL2 and DRAM - n DLL-on mode for normal frequency operation. If DDR4 CRC/parity retry is enabled (CRCPARCTL1.crc_parity_retry_enable = 1), d - l_off_mode is not supported, and this bit must be set to '0'.*/ -#undef DDRC_MSTR_DLL_OFF_MODE_DEFVAL -#undef DDRC_MSTR_DLL_OFF_MODE_SHIFT -#undef DDRC_MSTR_DLL_OFF_MODE_MASK -#define DDRC_MSTR_DLL_OFF_MODE_DEFVAL 0x03040001 -#define DDRC_MSTR_DLL_OFF_MODE_SHIFT 15 -#define DDRC_MSTR_DLL_OFF_MODE_MASK 0x00008000U - -/*Selects proportion of DQ bus width that is used by the SDRAM - 00 - Full DQ bus width to SDRAM - 01 - Half DQ bus width to SD - AM - 10 - Quarter DQ bus width to SDRAM - 11 - Reserved. Note that half bus width mode is only supported when the SDRAM bus w - dth is a multiple of 16, and quarter bus width mode is only supported when the SDRAM bus width is a multiple of 32 and the co - figuration parameter MEMC_QBUS_SUPPORT is set. Bus width refers to DQ bus width (excluding any ECC width).*/ -#undef DDRC_MSTR_DATA_BUS_WIDTH_DEFVAL -#undef DDRC_MSTR_DATA_BUS_WIDTH_SHIFT -#undef DDRC_MSTR_DATA_BUS_WIDTH_MASK -#define DDRC_MSTR_DATA_BUS_WIDTH_DEFVAL 0x03040001 -#define DDRC_MSTR_DATA_BUS_WIDTH_SHIFT 12 -#define DDRC_MSTR_DATA_BUS_WIDTH_MASK 0x00003000U - -/*1 indicates put the DRAM in geardown mode (2N) and 0 indicates put the DRAM in normal mode (1N). This register can be changed - only when the Controller is in self-refresh mode. This signal must be set the same value as MR3 bit A3. Note: Geardown mode - s not supported if the configuration parameter MEMC_CMD_RTN2IDLE is set*/ -#undef DDRC_MSTR_GEARDOWN_MODE_DEFVAL -#undef DDRC_MSTR_GEARDOWN_MODE_SHIFT -#undef DDRC_MSTR_GEARDOWN_MODE_MASK -#define DDRC_MSTR_GEARDOWN_MODE_DEFVAL 0x03040001 -#define DDRC_MSTR_GEARDOWN_MODE_SHIFT 11 -#define DDRC_MSTR_GEARDOWN_MODE_MASK 0x00000800U - -/*If 1, then uMCTL2 uses 2T timing. Otherwise, uses 1T timing. In 2T timing, all command signals (except chip select) are held - or 2 clocks on the SDRAM bus. Chip select is asserted on the second cycle of the command Note: 2T timing is not supported in - PDDR2/LPDDR3/LPDDR4 mode Note: 2T timing is not supported if the configuration parameter MEMC_CMD_RTN2IDLE is set Note: 2T ti - ing is not supported in DDR4 geardown mode.*/ -#undef DDRC_MSTR_EN_2T_TIMING_MODE_DEFVAL -#undef DDRC_MSTR_EN_2T_TIMING_MODE_SHIFT -#undef DDRC_MSTR_EN_2T_TIMING_MODE_MASK -#define DDRC_MSTR_EN_2T_TIMING_MODE_DEFVAL 0x03040001 -#define DDRC_MSTR_EN_2T_TIMING_MODE_SHIFT 10 -#define DDRC_MSTR_EN_2T_TIMING_MODE_MASK 0x00000400U - -/*When set, enable burst-chop in DDR3/DDR4. Burst Chop for Reads is exercised only in HIF configurations (UMCTL2_INCL_ARB not s - t) and if in full bus width mode (MSTR.data_bus_width = 00). Burst Chop for Writes is exercised only if Partial Writes enable - (UMCTL2_PARTIAL_WR=1) and if CRC is disabled (CRCPARCTL1.crc_enable = 0). If DDR4 CRC/parity retry is enabled (CRCPARCTL1.cr - _parity_retry_enable = 1), burst chop is not supported, and this bit must be set to '0'*/ -#undef DDRC_MSTR_BURSTCHOP_DEFVAL -#undef DDRC_MSTR_BURSTCHOP_SHIFT -#undef DDRC_MSTR_BURSTCHOP_MASK -#define DDRC_MSTR_BURSTCHOP_DEFVAL 0x03040001 -#define DDRC_MSTR_BURSTCHOP_SHIFT 9 -#define DDRC_MSTR_BURSTCHOP_MASK 0x00000200U - -/*Select LPDDR4 SDRAM - 1 - LPDDR4 SDRAM device in use. - 0 - non-LPDDR4 device in use Present only in designs configured to su - port LPDDR4.*/ -#undef DDRC_MSTR_LPDDR4_DEFVAL -#undef DDRC_MSTR_LPDDR4_SHIFT -#undef DDRC_MSTR_LPDDR4_MASK -#define DDRC_MSTR_LPDDR4_DEFVAL 0x03040001 -#define DDRC_MSTR_LPDDR4_SHIFT 5 -#define DDRC_MSTR_LPDDR4_MASK 0x00000020U - -/*Select DDR4 SDRAM - 1 - DDR4 SDRAM device in use. - 0 - non-DDR4 device in use Present only in designs configured to support - DR4.*/ -#undef DDRC_MSTR_DDR4_DEFVAL -#undef DDRC_MSTR_DDR4_SHIFT -#undef DDRC_MSTR_DDR4_MASK -#define DDRC_MSTR_DDR4_DEFVAL 0x03040001 -#define DDRC_MSTR_DDR4_SHIFT 4 -#define DDRC_MSTR_DDR4_MASK 0x00000010U - -/*Select LPDDR3 SDRAM - 1 - LPDDR3 SDRAM device in use. - 0 - non-LPDDR3 device in use Present only in designs configured to su - port LPDDR3.*/ -#undef DDRC_MSTR_LPDDR3_DEFVAL -#undef DDRC_MSTR_LPDDR3_SHIFT -#undef DDRC_MSTR_LPDDR3_MASK -#define DDRC_MSTR_LPDDR3_DEFVAL 0x03040001 -#define DDRC_MSTR_LPDDR3_SHIFT 3 -#define DDRC_MSTR_LPDDR3_MASK 0x00000008U - -/*Select LPDDR2 SDRAM - 1 - LPDDR2 SDRAM device in use. - 0 - non-LPDDR2 device in use Present only in designs configured to su - port LPDDR2.*/ -#undef DDRC_MSTR_LPDDR2_DEFVAL -#undef DDRC_MSTR_LPDDR2_SHIFT -#undef DDRC_MSTR_LPDDR2_MASK -#define DDRC_MSTR_LPDDR2_DEFVAL 0x03040001 -#define DDRC_MSTR_LPDDR2_SHIFT 2 -#define DDRC_MSTR_LPDDR2_MASK 0x00000004U - -/*Select DDR3 SDRAM - 1 - DDR3 SDRAM device in use - 0 - non-DDR3 SDRAM device in use Only present in designs that support DDR3 - */ -#undef DDRC_MSTR_DDR3_DEFVAL -#undef DDRC_MSTR_DDR3_SHIFT -#undef DDRC_MSTR_DDR3_MASK -#define DDRC_MSTR_DDR3_DEFVAL 0x03040001 -#define DDRC_MSTR_DDR3_SHIFT 0 -#define DDRC_MSTR_DDR3_MASK 0x00000001U - -/*Setting this register bit to 1 triggers a mode register read or write operation. When the MR operation is complete, the uMCTL - automatically clears this bit. The other register fields of this register must be written in a separate APB transaction, bef - re setting this mr_wr bit. It is recommended NOT to set this signal if in Init, Deep power-down or MPSM operating modes.*/ -#undef DDRC_MRCTRL0_MR_WR_DEFVAL -#undef DDRC_MRCTRL0_MR_WR_SHIFT -#undef DDRC_MRCTRL0_MR_WR_MASK -#define DDRC_MRCTRL0_MR_WR_DEFVAL 0x00000030 -#define DDRC_MRCTRL0_MR_WR_SHIFT 31 -#define DDRC_MRCTRL0_MR_WR_MASK 0x80000000U - -/*Address of the mode register that is to be written to. - 0000 - MR0 - 0001 - MR1 - 0010 - MR2 - 0011 - MR3 - 0100 - MR4 - 010 - - MR5 - 0110 - MR6 - 0111 - MR7 Don't Care for LPDDR2/LPDDR3/LPDDR4 (see MRCTRL1.mr_data for mode register addressing in LPD - R2/LPDDR3/LPDDR4) This signal is also used for writing to control words of RDIMMs. In that case, it corresponds to the bank a - dress bits sent to the RDIMM In case of DDR4, the bit[3:2] corresponds to the bank group bits. Therefore, the bit[3] as well - s the bit[2:0] must be set to an appropriate value which is considered both the Address Mirroring of UDIMMs/RDIMMs and the Ou - put Inversion of RDIMMs.*/ -#undef DDRC_MRCTRL0_MR_ADDR_DEFVAL -#undef DDRC_MRCTRL0_MR_ADDR_SHIFT -#undef DDRC_MRCTRL0_MR_ADDR_MASK -#define DDRC_MRCTRL0_MR_ADDR_DEFVAL 0x00000030 -#define DDRC_MRCTRL0_MR_ADDR_SHIFT 12 -#define DDRC_MRCTRL0_MR_ADDR_MASK 0x0000F000U - -/*Controls which rank is accessed by MRCTRL0.mr_wr. Normally, it is desired to access all ranks, so all bits should be set to 1 - However, for multi-rank UDIMMs/RDIMMs which implement address mirroring, it may be necessary to access ranks individually. E - amples (assume uMCTL2 is configured for 4 ranks): - 0x1 - select rank 0 only - 0x2 - select rank 1 only - 0x5 - select ranks - and 2 - 0xA - select ranks 1 and 3 - 0xF - select ranks 0, 1, 2 and 3*/ -#undef DDRC_MRCTRL0_MR_RANK_DEFVAL -#undef DDRC_MRCTRL0_MR_RANK_SHIFT -#undef DDRC_MRCTRL0_MR_RANK_MASK -#define DDRC_MRCTRL0_MR_RANK_DEFVAL 0x00000030 -#define DDRC_MRCTRL0_MR_RANK_SHIFT 4 -#define DDRC_MRCTRL0_MR_RANK_MASK 0x00000030U - -/*Indicates whether Software intervention is allowed via MRCTRL0/MRCTRL1 before automatic SDRAM initialization routine or not. - or DDR4, this bit can be used to initialize the DDR4 RCD (MR7) before automatic SDRAM initialization. For LPDDR4, this bit ca - be used to program additional mode registers before automatic SDRAM initialization if necessary. Note: This must be cleared - o 0 after completing Software operation. Otherwise, SDRAM initialization routine will not re-start. - 0 - Software interventi - n is not allowed - 1 - Software intervention is allowed*/ -#undef DDRC_MRCTRL0_SW_INIT_INT_DEFVAL -#undef DDRC_MRCTRL0_SW_INIT_INT_SHIFT -#undef DDRC_MRCTRL0_SW_INIT_INT_MASK -#define DDRC_MRCTRL0_SW_INIT_INT_DEFVAL 0x00000030 -#define DDRC_MRCTRL0_SW_INIT_INT_SHIFT 3 -#define DDRC_MRCTRL0_SW_INIT_INT_MASK 0x00000008U - -/*Indicates whether the mode register operation is MRS in PDA mode or not - 0 - MRS - 1 - MRS in Per DRAM Addressability mode*/ -#undef DDRC_MRCTRL0_PDA_EN_DEFVAL -#undef DDRC_MRCTRL0_PDA_EN_SHIFT -#undef DDRC_MRCTRL0_PDA_EN_MASK -#define DDRC_MRCTRL0_PDA_EN_DEFVAL 0x00000030 -#define DDRC_MRCTRL0_PDA_EN_SHIFT 2 -#define DDRC_MRCTRL0_PDA_EN_MASK 0x00000004U - -/*Indicates whether the mode register operation is MRS or WR/RD for MPR (only supported for DDR4) - 0 - MRS - 1 - WR/RD for MPR*/ -#undef DDRC_MRCTRL0_MPR_EN_DEFVAL -#undef DDRC_MRCTRL0_MPR_EN_SHIFT -#undef DDRC_MRCTRL0_MPR_EN_MASK -#define DDRC_MRCTRL0_MPR_EN_DEFVAL 0x00000030 -#define DDRC_MRCTRL0_MPR_EN_SHIFT 1 -#define DDRC_MRCTRL0_MPR_EN_MASK 0x00000002U - -/*Indicates whether the mode register operation is read or write. Only used for LPDDR2/LPDDR3/LPDDR4/DDR4. - 0 - Write - 1 - Re - d*/ -#undef DDRC_MRCTRL0_MR_TYPE_DEFVAL -#undef DDRC_MRCTRL0_MR_TYPE_SHIFT -#undef DDRC_MRCTRL0_MR_TYPE_MASK -#define DDRC_MRCTRL0_MR_TYPE_DEFVAL 0x00000030 -#define DDRC_MRCTRL0_MR_TYPE_SHIFT 0 -#define DDRC_MRCTRL0_MR_TYPE_MASK 0x00000001U - -/*Derate value of tRC for LPDDR4 - 0 - Derating uses +1. - 1 - Derating uses +2. - 2 - Derating uses +3. - 3 - Derating uses +4 - Present only in designs configured to support LPDDR4. The required number of cycles for derating can be determined by dividi - g 3.75ns by the core_ddrc_core_clk period, and rounding up the next integer.*/ -#undef DDRC_DERATEEN_RC_DERATE_VALUE_DEFVAL -#undef DDRC_DERATEEN_RC_DERATE_VALUE_SHIFT -#undef DDRC_DERATEEN_RC_DERATE_VALUE_MASK -#define DDRC_DERATEEN_RC_DERATE_VALUE_DEFVAL 0x00000000 -#define DDRC_DERATEEN_RC_DERATE_VALUE_SHIFT 8 -#define DDRC_DERATEEN_RC_DERATE_VALUE_MASK 0x00000300U - -/*Derate byte Present only in designs configured to support LPDDR2/LPDDR3/LPDDR4 Indicates which byte of the MRR data is used f - r derating. The maximum valid value depends on MEMC_DRAM_TOTAL_DATA_WIDTH.*/ -#undef DDRC_DERATEEN_DERATE_BYTE_DEFVAL -#undef DDRC_DERATEEN_DERATE_BYTE_SHIFT -#undef DDRC_DERATEEN_DERATE_BYTE_MASK -#define DDRC_DERATEEN_DERATE_BYTE_DEFVAL 0x00000000 -#define DDRC_DERATEEN_DERATE_BYTE_SHIFT 4 -#define DDRC_DERATEEN_DERATE_BYTE_MASK 0x000000F0U - -/*Derate value - 0 - Derating uses +1. - 1 - Derating uses +2. Present only in designs configured to support LPDDR2/LPDDR3/LPDD - 4 Set to 0 for all LPDDR2 speed grades as derating value of +1.875 ns is less than a core_ddrc_core_clk period. Can be 0 or 1 - for LPDDR3/LPDDR4, depending if +1.875 ns is less than a core_ddrc_core_clk period or not.*/ -#undef DDRC_DERATEEN_DERATE_VALUE_DEFVAL -#undef DDRC_DERATEEN_DERATE_VALUE_SHIFT -#undef DDRC_DERATEEN_DERATE_VALUE_MASK -#define DDRC_DERATEEN_DERATE_VALUE_DEFVAL 0x00000000 -#define DDRC_DERATEEN_DERATE_VALUE_SHIFT 1 -#define DDRC_DERATEEN_DERATE_VALUE_MASK 0x00000002U - -/*Enables derating - 0 - Timing parameter derating is disabled - 1 - Timing parameter derating is enabled using MR4 read value. - Present only in designs configured to support LPDDR2/LPDDR3/LPDDR4 This field must be set to '0' for non-LPDDR2/LPDDR3/LPDDR4 - mode.*/ -#undef DDRC_DERATEEN_DERATE_ENABLE_DEFVAL -#undef DDRC_DERATEEN_DERATE_ENABLE_SHIFT -#undef DDRC_DERATEEN_DERATE_ENABLE_MASK -#define DDRC_DERATEEN_DERATE_ENABLE_DEFVAL 0x00000000 -#define DDRC_DERATEEN_DERATE_ENABLE_SHIFT 0 -#define DDRC_DERATEEN_DERATE_ENABLE_MASK 0x00000001U - -/*Interval between two MR4 reads, used to derate the timing parameters. Present only in designs configured to support LPDDR2/LP - DR3/LPDDR4. This register must not be set to zero*/ -#undef DDRC_DERATEINT_MR4_READ_INTERVAL_DEFVAL -#undef DDRC_DERATEINT_MR4_READ_INTERVAL_SHIFT -#undef DDRC_DERATEINT_MR4_READ_INTERVAL_MASK -#define DDRC_DERATEINT_MR4_READ_INTERVAL_DEFVAL -#define DDRC_DERATEINT_MR4_READ_INTERVAL_SHIFT 0 -#define DDRC_DERATEINT_MR4_READ_INTERVAL_MASK 0xFFFFFFFFU - -/*Self refresh state is an intermediate state to enter to Self refresh power down state or exit Self refresh power down state f - r LPDDR4. This register controls transition from the Self refresh state. - 1 - Prohibit transition from Self refresh state - - - Allow transition from Self refresh state*/ -#undef DDRC_PWRCTL_STAY_IN_SELFREF_DEFVAL -#undef DDRC_PWRCTL_STAY_IN_SELFREF_SHIFT -#undef DDRC_PWRCTL_STAY_IN_SELFREF_MASK -#define DDRC_PWRCTL_STAY_IN_SELFREF_DEFVAL 0x00000000 -#define DDRC_PWRCTL_STAY_IN_SELFREF_SHIFT 6 -#define DDRC_PWRCTL_STAY_IN_SELFREF_MASK 0x00000040U - -/*A value of 1 to this register causes system to move to Self Refresh state immediately, as long as it is not in INIT or DPD/MP - M operating_mode. This is referred to as Software Entry/Exit to Self Refresh. - 1 - Software Entry to Self Refresh - 0 - Soft - are Exit from Self Refresh*/ -#undef DDRC_PWRCTL_SELFREF_SW_DEFVAL -#undef DDRC_PWRCTL_SELFREF_SW_SHIFT -#undef DDRC_PWRCTL_SELFREF_SW_MASK -#define DDRC_PWRCTL_SELFREF_SW_DEFVAL 0x00000000 -#define DDRC_PWRCTL_SELFREF_SW_SHIFT 5 -#define DDRC_PWRCTL_SELFREF_SW_MASK 0x00000020U - -/*When this is 1, the uMCTL2 puts the SDRAM into maximum power saving mode when the transaction store is empty. This register m - st be reset to '0' to bring uMCTL2 out of maximum power saving mode. Present only in designs configured to support DDR4. For - on-DDR4, this register should not be set to 1. Note that MPSM is not supported when using a DWC DDR PHY, if the PHY parameter - DWC_AC_CS_USE is disabled, as the MPSM exit sequence requires the chip-select signal to toggle. FOR PERFORMANCE ONLY.*/ -#undef DDRC_PWRCTL_MPSM_EN_DEFVAL -#undef DDRC_PWRCTL_MPSM_EN_SHIFT -#undef DDRC_PWRCTL_MPSM_EN_MASK -#define DDRC_PWRCTL_MPSM_EN_DEFVAL 0x00000000 -#define DDRC_PWRCTL_MPSM_EN_SHIFT 4 -#define DDRC_PWRCTL_MPSM_EN_MASK 0x00000010U - -/*Enable the assertion of dfi_dram_clk_disable whenever a clock is not required by the SDRAM. If set to 0, dfi_dram_clk_disable - is never asserted. Assertion of dfi_dram_clk_disable is as follows: In DDR2/DDR3, can only be asserted in Self Refresh. In DD - 4, can be asserted in following: - in Self Refresh. - in Maximum Power Saving Mode In mDDR/LPDDR2/LPDDR3, can be asserted in - ollowing: - in Self Refresh - in Power Down - in Deep Power Down - during Normal operation (Clock Stop) In LPDDR4, can be ass - rted in following: - in Self Refresh Power Down - in Power Down - during Normal operation (Clock Stop)*/ -#undef DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE_DEFVAL -#undef DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE_SHIFT -#undef DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE_MASK -#define DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE_DEFVAL 0x00000000 -#define DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE_SHIFT 3 -#define DDRC_PWRCTL_EN_DFI_DRAM_CLK_DISABLE_MASK 0x00000008U - -/*When this is 1, uMCTL2 puts the SDRAM into deep power-down mode when the transaction store is empty. This register must be re - et to '0' to bring uMCTL2 out of deep power-down mode. Controller performs automatic SDRAM initialization on deep power-down - xit. Present only in designs configured to support mDDR or LPDDR2 or LPDDR3. For non-mDDR/non-LPDDR2/non-LPDDR3, this registe - should not be set to 1. FOR PERFORMANCE ONLY.*/ -#undef DDRC_PWRCTL_DEEPPOWERDOWN_EN_DEFVAL -#undef DDRC_PWRCTL_DEEPPOWERDOWN_EN_SHIFT -#undef DDRC_PWRCTL_DEEPPOWERDOWN_EN_MASK -#define DDRC_PWRCTL_DEEPPOWERDOWN_EN_DEFVAL 0x00000000 -#define DDRC_PWRCTL_DEEPPOWERDOWN_EN_SHIFT 2 -#define DDRC_PWRCTL_DEEPPOWERDOWN_EN_MASK 0x00000004U - -/*If true then the uMCTL2 goes into power-down after a programmable number of cycles 'maximum idle clocks before power down' (P - RTMG.powerdown_to_x32). This register bit may be re-programmed during the course of normal operation.*/ -#undef DDRC_PWRCTL_POWERDOWN_EN_DEFVAL -#undef DDRC_PWRCTL_POWERDOWN_EN_SHIFT -#undef DDRC_PWRCTL_POWERDOWN_EN_MASK -#define DDRC_PWRCTL_POWERDOWN_EN_DEFVAL 0x00000000 -#define DDRC_PWRCTL_POWERDOWN_EN_SHIFT 1 -#define DDRC_PWRCTL_POWERDOWN_EN_MASK 0x00000002U - -/*If true then the uMCTL2 puts the SDRAM into Self Refresh after a programmable number of cycles 'maximum idle clocks before Se - f Refresh (PWRTMG.selfref_to_x32)'. This register bit may be re-programmed during the course of normal operation.*/ -#undef DDRC_PWRCTL_SELFREF_EN_DEFVAL -#undef DDRC_PWRCTL_SELFREF_EN_SHIFT -#undef DDRC_PWRCTL_SELFREF_EN_MASK -#define DDRC_PWRCTL_SELFREF_EN_DEFVAL 0x00000000 -#define DDRC_PWRCTL_SELFREF_EN_SHIFT 0 -#define DDRC_PWRCTL_SELFREF_EN_MASK 0x00000001U - -/*After this many clocks of NOP or deselect the uMCTL2 automatically puts the SDRAM into Self Refresh. This must be enabled in - he PWRCTL.selfref_en. Unit: Multiples of 32 clocks. FOR PERFORMANCE ONLY.*/ -#undef DDRC_PWRTMG_SELFREF_TO_X32_DEFVAL -#undef DDRC_PWRTMG_SELFREF_TO_X32_SHIFT -#undef DDRC_PWRTMG_SELFREF_TO_X32_MASK -#define DDRC_PWRTMG_SELFREF_TO_X32_DEFVAL 0x00402010 -#define DDRC_PWRTMG_SELFREF_TO_X32_SHIFT 16 -#define DDRC_PWRTMG_SELFREF_TO_X32_MASK 0x00FF0000U - -/*Minimum deep power-down time. For mDDR, value from the JEDEC specification is 0 as mDDR exits from deep power-down mode immed - ately after PWRCTL.deeppowerdown_en is de-asserted. For LPDDR2/LPDDR3, value from the JEDEC specification is 500us. Unit: Mul - iples of 4096 clocks. Present only in designs configured to support mDDR, LPDDR2 or LPDDR3. FOR PERFORMANCE ONLY.*/ -#undef DDRC_PWRTMG_T_DPD_X4096_DEFVAL -#undef DDRC_PWRTMG_T_DPD_X4096_SHIFT -#undef DDRC_PWRTMG_T_DPD_X4096_MASK -#define DDRC_PWRTMG_T_DPD_X4096_DEFVAL 0x00402010 -#define DDRC_PWRTMG_T_DPD_X4096_SHIFT 8 -#define DDRC_PWRTMG_T_DPD_X4096_MASK 0x0000FF00U - -/*After this many clocks of NOP or deselect the uMCTL2 automatically puts the SDRAM into power-down. This must be enabled in th - PWRCTL.powerdown_en. Unit: Multiples of 32 clocks FOR PERFORMANCE ONLY.*/ -#undef DDRC_PWRTMG_POWERDOWN_TO_X32_DEFVAL -#undef DDRC_PWRTMG_POWERDOWN_TO_X32_SHIFT -#undef DDRC_PWRTMG_POWERDOWN_TO_X32_MASK -#define DDRC_PWRTMG_POWERDOWN_TO_X32_DEFVAL 0x00402010 -#define DDRC_PWRTMG_POWERDOWN_TO_X32_SHIFT 0 -#define DDRC_PWRTMG_POWERDOWN_TO_X32_MASK 0x0000001FU - -/*Threshold value in number of clock cycles before the critical refresh or page timer expires. A critical refresh is to be issu - d before this threshold is reached. It is recommended that this not be changed from the default value, currently shown as 0x2 - It must always be less than internally used t_rfc_nom_x32. Note that, in LPDDR2/LPDDR3/LPDDR4, internally used t_rfc_nom_x32 - may be equal to RFSHTMG.t_rfc_nom_x32>>2 if derating is enabled (DERATEEN.derate_enable=1). Otherwise, internally used t_rfc_ - om_x32 will be equal to RFSHTMG.t_rfc_nom_x32. Unit: Multiples of 32 clocks.*/ -#undef DDRC_RFSHCTL0_REFRESH_MARGIN_DEFVAL -#undef DDRC_RFSHCTL0_REFRESH_MARGIN_SHIFT -#undef DDRC_RFSHCTL0_REFRESH_MARGIN_MASK -#define DDRC_RFSHCTL0_REFRESH_MARGIN_DEFVAL 0x00210000 -#define DDRC_RFSHCTL0_REFRESH_MARGIN_SHIFT 20 -#define DDRC_RFSHCTL0_REFRESH_MARGIN_MASK 0x00F00000U - -/*If the refresh timer (tRFCnom, also known as tREFI) has expired at least once, but it has not expired (RFSHCTL0.refresh_burst - 1) times yet, then a speculative refresh may be performed. A speculative refresh is a refresh performed at a time when refres - would be useful, but before it is absolutely required. When the SDRAM bus is idle for a period of time determined by this RF - HCTL0.refresh_to_x32 and the refresh timer has expired at least once since the last refresh, then a speculative refresh is pe - formed. Speculative refreshes continues successively until there are no refreshes pending or until new reads or writes are is - ued to the uMCTL2. FOR PERFORMANCE ONLY.*/ -#undef DDRC_RFSHCTL0_REFRESH_TO_X32_DEFVAL -#undef DDRC_RFSHCTL0_REFRESH_TO_X32_SHIFT -#undef DDRC_RFSHCTL0_REFRESH_TO_X32_MASK -#define DDRC_RFSHCTL0_REFRESH_TO_X32_DEFVAL 0x00210000 -#define DDRC_RFSHCTL0_REFRESH_TO_X32_SHIFT 12 -#define DDRC_RFSHCTL0_REFRESH_TO_X32_MASK 0x0001F000U - -/*The programmed value + 1 is the number of refresh timeouts that is allowed to accumulate before traffic is blocked and the re - reshes are forced to execute. Closing pages to perform a refresh is a one-time penalty that must be paid for each group of re - reshes. Therefore, performing refreshes in a burst reduces the per-refresh penalty of these page closings. Higher numbers for - RFSHCTL.refresh_burst slightly increases utilization; lower numbers decreases the worst-case latency associated with refreshe - . - 0 - single refresh - 1 - burst-of-2 refresh - 7 - burst-of-8 refresh For information on burst refresh feature refer to se - tion 3.9 of DDR2 JEDEC specification - JESD79-2F.pdf. For DDR2/3, the refresh is always per-rank and not per-bank. The rank r - fresh can be accumulated over 8*tREFI cycles using the burst refresh feature. In DDR4 mode, according to Fine Granularity fea - ure, 8 refreshes can be postponed in 1X mode, 16 refreshes in 2X mode and 32 refreshes in 4X mode. If using PHY-initiated upd - tes, care must be taken in the setting of RFSHCTL0.refresh_burst, to ensure that tRFCmax is not violated due to a PHY-initiat - d update occurring shortly before a refresh burst was due. In this situation, the refresh burst will be delayed until the PHY - initiated update is complete.*/ -#undef DDRC_RFSHCTL0_REFRESH_BURST_DEFVAL -#undef DDRC_RFSHCTL0_REFRESH_BURST_SHIFT -#undef DDRC_RFSHCTL0_REFRESH_BURST_MASK -#define DDRC_RFSHCTL0_REFRESH_BURST_DEFVAL 0x00210000 -#define DDRC_RFSHCTL0_REFRESH_BURST_SHIFT 4 -#define DDRC_RFSHCTL0_REFRESH_BURST_MASK 0x000001F0U - -/*- 1 - Per bank refresh; - 0 - All bank refresh. Per bank refresh allows traffic to flow to other banks. Per bank refresh is n - t supported by all LPDDR2 devices but should be supported by all LPDDR3/LPDDR4 devices. Present only in designs configured to - support LPDDR2/LPDDR3/LPDDR4*/ -#undef DDRC_RFSHCTL0_PER_BANK_REFRESH_DEFVAL -#undef DDRC_RFSHCTL0_PER_BANK_REFRESH_SHIFT -#undef DDRC_RFSHCTL0_PER_BANK_REFRESH_MASK -#define DDRC_RFSHCTL0_PER_BANK_REFRESH_DEFVAL 0x00210000 -#define DDRC_RFSHCTL0_PER_BANK_REFRESH_SHIFT 2 -#define DDRC_RFSHCTL0_PER_BANK_REFRESH_MASK 0x00000004U - -/*Fine Granularity Refresh Mode - 000 - Fixed 1x (Normal mode) - 001 - Fixed 2x - 010 - Fixed 4x - 101 - Enable on the fly 2x ( - ot supported) - 110 - Enable on the fly 4x (not supported) - Everything else - reserved Note: The on-the-fly modes is not sup - orted in this version of the uMCTL2. Note: This must be set up while the Controller is in reset or while the Controller is in - self-refresh mode. Changing this during normal operation is not allowed. Making this a dynamic register will be supported in - uture version of the uMCTL2.*/ -#undef DDRC_RFSHCTL3_REFRESH_MODE_DEFVAL -#undef DDRC_RFSHCTL3_REFRESH_MODE_SHIFT -#undef DDRC_RFSHCTL3_REFRESH_MODE_MASK -#define DDRC_RFSHCTL3_REFRESH_MODE_DEFVAL 0x00000000 -#define DDRC_RFSHCTL3_REFRESH_MODE_SHIFT 4 -#define DDRC_RFSHCTL3_REFRESH_MODE_MASK 0x00000070U - -/*Toggle this signal (either from 0 to 1 or from 1 to 0) to indicate that the refresh register(s) have been updated. The value - s automatically updated when exiting reset, so it does not need to be toggled initially.*/ -#undef DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL_DEFVAL -#undef DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL_SHIFT -#undef DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL_MASK -#define DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL_DEFVAL 0x00000000 -#define DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL_SHIFT 1 -#define DDRC_RFSHCTL3_REFRESH_UPDATE_LEVEL_MASK 0x00000002U - -/*When '1', disable auto-refresh generated by the uMCTL2. When auto-refresh is disabled, the SoC core must generate refreshes u - ing the registers reg_ddrc_rank0_refresh, reg_ddrc_rank1_refresh, reg_ddrc_rank2_refresh and reg_ddrc_rank3_refresh. When dis - auto_refresh transitions from 0 to 1, any pending refreshes are immediately scheduled by the uMCTL2. If DDR4 CRC/parity retry - is enabled (CRCPARCTL1.crc_parity_retry_enable = 1), disable auto-refresh is not supported, and this bit must be set to '0'. - his register field is changeable on the fly.*/ -#undef DDRC_RFSHCTL3_DIS_AUTO_REFRESH_DEFVAL -#undef DDRC_RFSHCTL3_DIS_AUTO_REFRESH_SHIFT -#undef DDRC_RFSHCTL3_DIS_AUTO_REFRESH_MASK -#define DDRC_RFSHCTL3_DIS_AUTO_REFRESH_DEFVAL 0x00000000 -#define DDRC_RFSHCTL3_DIS_AUTO_REFRESH_SHIFT 0 -#define DDRC_RFSHCTL3_DIS_AUTO_REFRESH_MASK 0x00000001U - -/*tREFI: Average time interval between refreshes per rank (Specification: 7.8us for DDR2, DDR3 and DDR4. See JEDEC specificatio - for mDDR, LPDDR2, LPDDR3 and LPDDR4). For LPDDR2/LPDDR3/LPDDR4: - if using all-bank refreshes (RFSHCTL0.per_bank_refresh = 0 - , this register should be set to tREFIab - if using per-bank refreshes (RFSHCTL0.per_bank_refresh = 1), this register should - e set to tREFIpb For configurations with MEMC_FREQ_RATIO=2, program this to (tREFI/2), no rounding up. In DDR4 mode, tREFI va - ue is different depending on the refresh mode. The user should program the appropriate value from the spec based on the value - programmed in the refresh mode register. Note that RFSHTMG.t_rfc_nom_x32 * 32 must be greater than RFSHTMG.t_rfc_min, and RFS - TMG.t_rfc_nom_x32 must be greater than 0x1. Unit: Multiples of 32 clocks.*/ -#undef DDRC_RFSHTMG_T_RFC_NOM_X32_DEFVAL -#undef DDRC_RFSHTMG_T_RFC_NOM_X32_SHIFT -#undef DDRC_RFSHTMG_T_RFC_NOM_X32_MASK -#define DDRC_RFSHTMG_T_RFC_NOM_X32_DEFVAL 0x0062008C -#define DDRC_RFSHTMG_T_RFC_NOM_X32_SHIFT 16 -#define DDRC_RFSHTMG_T_RFC_NOM_X32_MASK 0x0FFF0000U - -/*Used only when LPDDR3 memory type is connected. Should only be changed when uMCTL2 is in reset. Specifies whether to use the - REFBW parameter (required by some LPDDR3 devices which comply with earlier versions of the LPDDR3 JEDEC specification) or not - - 0 - tREFBW parameter not used - 1 - tREFBW parameter used*/ -#undef DDRC_RFSHTMG_LPDDR3_TREFBW_EN_DEFVAL -#undef DDRC_RFSHTMG_LPDDR3_TREFBW_EN_SHIFT -#undef DDRC_RFSHTMG_LPDDR3_TREFBW_EN_MASK -#define DDRC_RFSHTMG_LPDDR3_TREFBW_EN_DEFVAL 0x0062008C -#define DDRC_RFSHTMG_LPDDR3_TREFBW_EN_SHIFT 15 -#define DDRC_RFSHTMG_LPDDR3_TREFBW_EN_MASK 0x00008000U - -/*tRFC (min): Minimum time from refresh to refresh or activate. For MEMC_FREQ_RATIO=1 configurations, t_rfc_min should be set t - RoundUp(tRFCmin/tCK). For MEMC_FREQ_RATIO=2 configurations, t_rfc_min should be set to RoundUp(RoundUp(tRFCmin/tCK)/2). In L - DDR2/LPDDR3/LPDDR4 mode: - if using all-bank refreshes, the tRFCmin value in the above equations is equal to tRFCab - if usin - per-bank refreshes, the tRFCmin value in the above equations is equal to tRFCpb In DDR4 mode, the tRFCmin value in the above - equations is different depending on the refresh mode (fixed 1X,2X,4X) and the device density. The user should program the app - opriate value from the spec based on the 'refresh_mode' and the device density that is used. Unit: Clocks.*/ -#undef DDRC_RFSHTMG_T_RFC_MIN_DEFVAL -#undef DDRC_RFSHTMG_T_RFC_MIN_SHIFT -#undef DDRC_RFSHTMG_T_RFC_MIN_MASK -#define DDRC_RFSHTMG_T_RFC_MIN_DEFVAL 0x0062008C -#define DDRC_RFSHTMG_T_RFC_MIN_SHIFT 0 -#define DDRC_RFSHTMG_T_RFC_MIN_MASK 0x000003FFU - -/*Disable ECC scrubs. Valid only when ECCCFG0.ecc_mode = 3'b100 and MEMC_USE_RMW is defined*/ -#undef DDRC_ECCCFG0_DIS_SCRUB_DEFVAL -#undef DDRC_ECCCFG0_DIS_SCRUB_SHIFT -#undef DDRC_ECCCFG0_DIS_SCRUB_MASK -#define DDRC_ECCCFG0_DIS_SCRUB_DEFVAL 0x00000000 -#define DDRC_ECCCFG0_DIS_SCRUB_SHIFT 4 -#define DDRC_ECCCFG0_DIS_SCRUB_MASK 0x00000010U - -/*ECC mode indicator - 000 - ECC disabled - 100 - ECC enabled - SEC/DED over 1 beat - all other settings are reserved for futur - use*/ -#undef DDRC_ECCCFG0_ECC_MODE_DEFVAL -#undef DDRC_ECCCFG0_ECC_MODE_SHIFT -#undef DDRC_ECCCFG0_ECC_MODE_MASK -#define DDRC_ECCCFG0_ECC_MODE_DEFVAL 0x00000000 -#define DDRC_ECCCFG0_ECC_MODE_SHIFT 0 -#define DDRC_ECCCFG0_ECC_MODE_MASK 0x00000007U - -/*Selects whether to poison 1 or 2 bits - if 0 -> 2-bit (uncorrectable) data poisoning, if 1 -> 1-bit (correctable) data poison - ng, if ECCCFG1.data_poison_en=1*/ -#undef DDRC_ECCCFG1_DATA_POISON_BIT_DEFVAL -#undef DDRC_ECCCFG1_DATA_POISON_BIT_SHIFT -#undef DDRC_ECCCFG1_DATA_POISON_BIT_MASK -#define DDRC_ECCCFG1_DATA_POISON_BIT_DEFVAL 0x00000000 -#define DDRC_ECCCFG1_DATA_POISON_BIT_SHIFT 1 -#define DDRC_ECCCFG1_DATA_POISON_BIT_MASK 0x00000002U - -/*Enable ECC data poisoning - introduces ECC errors on writes to address specified by the ECCPOISONADDR0/1 registers*/ -#undef DDRC_ECCCFG1_DATA_POISON_EN_DEFVAL -#undef DDRC_ECCCFG1_DATA_POISON_EN_SHIFT -#undef DDRC_ECCCFG1_DATA_POISON_EN_MASK -#define DDRC_ECCCFG1_DATA_POISON_EN_DEFVAL 0x00000000 -#define DDRC_ECCCFG1_DATA_POISON_EN_SHIFT 0 -#define DDRC_ECCCFG1_DATA_POISON_EN_MASK 0x00000001U - -/*The maximum number of DFI PHY clock cycles allowed from the assertion of the dfi_rddata_en signal to the assertion of each of - the corresponding bits of the dfi_rddata_valid signal. This corresponds to the DFI timing parameter tphy_rdlat. Refer to PHY - pecification for correct value. This value it only used for detecting read data timeout when DDR4 retry is enabled by CRCPARC - L1.crc_parity_retry_enable=1. Maximum supported value: - 1:1 Frequency mode : DFITMG0.dfi_t_rddata_en + CRCPARCTL1.dfi_t_phy_ - dlat < 'd114 - 1:2 Frequency mode ANDAND DFITMG0.dfi_rddata_use_sdr == 1 : CRCPARCTL1.dfi_t_phy_rdlat < 64 - 1:2 Frequency mo - e ANDAND DFITMG0.dfi_rddata_use_sdr == 0 : DFITMG0.dfi_t_rddata_en + CRCPARCTL1.dfi_t_phy_rdlat < 'd114 Unit: DFI Clocks*/ -#undef DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT_DEFVAL -#undef DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT_SHIFT -#undef DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT_MASK -#define DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT_DEFVAL 0x10000200 -#define DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT_SHIFT 24 -#define DDRC_CRCPARCTL1_DFI_T_PHY_RDLAT_MASK 0x3F000000U - -/*After a Parity or CRC error is flagged on dfi_alert_n signal, the software has an option to read the mode registers in the DR - M before the hardware begins the retry process - 1: Wait for software to read/write the mode registers before hardware begins - the retry. After software is done with its operations, it will clear the alert interrupt register bit - 0: Hardware can begin - the retry right away after the dfi_alert_n pulse goes away. The value on this register is valid only when retry is enabled (P - RCTRL.crc_parity_retry_enable = 1) If this register is set to 1 and if the software doesn't clear the interrupt register afte - handling the parity/CRC error, then the hardware will not begin the retry process and the system will hang. In the case of P - rity/CRC error, there are two possibilities when the software doesn't reset MR5[4] to 0. - (i) If 'Persistent parity' mode re - ister bit is NOT set: the commands sent during retry and normal operation are executed without parity checking. The value in - he Parity error log register MPR Page 1 is valid. - (ii) If 'Persistent parity' mode register bit is SET: Parity checking is - one for commands sent during retry and normal operation. If multiple errors occur before MR5[4] is cleared, the error log in - PR Page 1 should be treated as 'Don't care'.*/ -#undef DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW_DEFVAL -#undef DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW_SHIFT -#undef DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW_MASK -#define DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW_DEFVAL 0x10000200 -#define DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW_SHIFT 9 -#define DDRC_CRCPARCTL1_ALERT_WAIT_FOR_SW_MASK 0x00000200U - -/*- 1: Enable command retry mechanism in case of C/A Parity or CRC error - 0: Disable command retry mechanism when C/A Parity o - CRC features are enabled. Note that retry functionality is not supported if burst chop is enabled (MSTR.burstchop = 1) and/o - disable auto-refresh is enabled (RFSHCTL3.dis_auto_refresh = 1)*/ -#undef DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE_DEFVAL -#undef DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE_SHIFT -#undef DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE_MASK -#define DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE_DEFVAL 0x10000200 -#define DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE_SHIFT 8 -#define DDRC_CRCPARCTL1_CRC_PARITY_RETRY_ENABLE_MASK 0x00000100U - -/*CRC Calculation setting register - 1: CRC includes DM signal - 0: CRC not includes DM signal Present only in designs configur - d to support DDR4.*/ -#undef DDRC_CRCPARCTL1_CRC_INC_DM_DEFVAL -#undef DDRC_CRCPARCTL1_CRC_INC_DM_SHIFT -#undef DDRC_CRCPARCTL1_CRC_INC_DM_MASK -#define DDRC_CRCPARCTL1_CRC_INC_DM_DEFVAL 0x10000200 -#define DDRC_CRCPARCTL1_CRC_INC_DM_SHIFT 7 -#define DDRC_CRCPARCTL1_CRC_INC_DM_MASK 0x00000080U - -/*CRC enable Register - 1: Enable generation of CRC - 0: Disable generation of CRC The setting of this register should match th - CRC mode register setting in the DRAM.*/ -#undef DDRC_CRCPARCTL1_CRC_ENABLE_DEFVAL -#undef DDRC_CRCPARCTL1_CRC_ENABLE_SHIFT -#undef DDRC_CRCPARCTL1_CRC_ENABLE_MASK -#define DDRC_CRCPARCTL1_CRC_ENABLE_DEFVAL 0x10000200 -#define DDRC_CRCPARCTL1_CRC_ENABLE_SHIFT 4 -#define DDRC_CRCPARCTL1_CRC_ENABLE_MASK 0x00000010U - -/*C/A Parity enable register - 1: Enable generation of C/A parity and detection of C/A parity error - 0: Disable generation of - /A parity and disable detection of C/A parity error If RCD's parity error detection or SDRAM's parity detection is enabled, t - is register should be 1.*/ -#undef DDRC_CRCPARCTL1_PARITY_ENABLE_DEFVAL -#undef DDRC_CRCPARCTL1_PARITY_ENABLE_SHIFT -#undef DDRC_CRCPARCTL1_PARITY_ENABLE_MASK -#define DDRC_CRCPARCTL1_PARITY_ENABLE_DEFVAL 0x10000200 -#define DDRC_CRCPARCTL1_PARITY_ENABLE_SHIFT 0 -#define DDRC_CRCPARCTL1_PARITY_ENABLE_MASK 0x00000001U - -/*Value from the DRAM spec indicating the maximum width of the dfi_alert_n pulse when a parity error occurs. Recommended values - - tPAR_ALERT_PW.MAX For configurations with MEMC_FREQ_RATIO=2, program this to tPAR_ALERT_PW.MAX/2 and round up to next inte - er value. Values of 0, 1 and 2 are illegal. This value must be greater than CRCPARCTL2.t_crc_alert_pw_max.*/ -#undef DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX_DEFVAL -#undef DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX_SHIFT -#undef DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX_MASK -#define DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX_DEFVAL 0x0030050C -#define DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX_SHIFT 16 -#define DDRC_CRCPARCTL2_T_PAR_ALERT_PW_MAX_MASK 0x01FF0000U - -/*Value from the DRAM spec indicating the maximum width of the dfi_alert_n pulse when a CRC error occurs. Recommended values: - - tCRC_ALERT_PW.MAX For configurations with MEMC_FREQ_RATIO=2, program this to tCRC_ALERT_PW.MAX/2 and round up to next integer - value. Values of 0, 1 and 2 are illegal. This value must be less than CRCPARCTL2.t_par_alert_pw_max.*/ -#undef DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX_DEFVAL -#undef DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX_SHIFT -#undef DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX_MASK -#define DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX_DEFVAL 0x0030050C -#define DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX_SHIFT 8 -#define DDRC_CRCPARCTL2_T_CRC_ALERT_PW_MAX_MASK 0x00001F00U - -/*Indicates the maximum duration in number of DRAM clock cycles for which a command should be held in the Command Retry FIFO be - ore it is popped out. Every location in the Command Retry FIFO has an associated down counting timer that will use this regis - er as the start value. The down counting starts when a command is loaded into the FIFO. The timer counts down every 4 DRAM cy - les. When the counter reaches zero, the entry is popped from the FIFO. All the counters are frozen, if a C/A Parity or CRC er - or occurs before the counter reaches zero. The counter is reset to 0, after all the commands in the FIFO are retried. Recomme - ded(minimum) values: - Only C/A Parity is enabled. RoundUp((PHY Command Latency(DRAM CLK) + CAL + RDIMM delay + tPAR_ALERT_ON - max + tPAR_UNKNOWN + PHY Alert Latency(DRAM CLK) + board delay) / 4) + 2 - Both C/A Parity and CRC is enabled/ Only CRC is en - bled. RoundUp((PHY Command Latency(DRAM CLK) + CAL + RDIMM delay + WL + 5(BL10)+ tCRC_ALERT.max + PHY Alert Latency(DRAM CLK) - + board delay) / 4) + 2 Note 1: All value (e.g. tPAR_ALERT_ON) should be in terms of DRAM Clock and round up Note 2: Board de - ay(Command/Alert_n) should be considered. Note 3: Use the worst case(longer) value for PHY Latencies/Board delay Note 4: The - ecommended values are minimum value to be set. For mode detail, See 'Calculation of FIFO Depth' section. Max value can be set - to this register is defined below: - MEMC_BURST_LENGTH == 16 Full bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH- - Full bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-3 Half bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_D - PTH-4 Half bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-6 Quarter bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CM - _FIFO_DEPTH-8 Quarter bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-12 - MEMC_BURST_LENGTH != 16 Full bus Mode (C - C=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-1 Full bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-2 Half bus Mo - e (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-2 Half bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-3 Quarte - bus Mode (CRC=OFF) Max value = UMCTL2_RETRY_CMD_FIFO_DEPTH-4 Quarter bus Mode (CRC=ON) Max value = UMCTL2_RETRY_CMD_FIFO_DEP - H-6 Values of 0, 1 and 2 are illegal.*/ -#undef DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4_DEFVAL -#undef DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4_SHIFT -#undef DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4_MASK -#define DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4_DEFVAL 0x0030050C -#define DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4_SHIFT 0 -#define DDRC_CRCPARCTL2_RETRY_FIFO_MAX_HOLD_TIMER_X4_MASK 0x0000003FU - -/*If lower bit is enabled the SDRAM initialization routine is skipped. The upper bit decides what state the controller starts u - in when reset is removed - 00 - SDRAM Intialization routine is run after power-up - 01 - SDRAM Intialization routine is skip - ed after power-up. Controller starts up in Normal Mode - 11 - SDRAM Intialization routine is skipped after power-up. Controll - r starts up in Self-refresh Mode - 10 - SDRAM Intialization routine is run after power-up. Note: The only 2'b00 is supported - or LPDDR4 in this version of the uMCTL2.*/ -#undef DDRC_INIT0_SKIP_DRAM_INIT_DEFVAL -#undef DDRC_INIT0_SKIP_DRAM_INIT_SHIFT -#undef DDRC_INIT0_SKIP_DRAM_INIT_MASK -#define DDRC_INIT0_SKIP_DRAM_INIT_DEFVAL 0x0002004E -#define DDRC_INIT0_SKIP_DRAM_INIT_SHIFT 30 -#define DDRC_INIT0_SKIP_DRAM_INIT_MASK 0xC0000000U - -/*Cycles to wait after driving CKE high to start the SDRAM initialization sequence. Unit: 1024 clocks. DDR2 typically requires - 400 ns delay, requiring this value to be programmed to 2 at all clock speeds. LPDDR2/LPDDR3 typically requires this to be pr - grammed for a delay of 200 us. LPDDR4 typically requires this to be programmed for a delay of 2 us. For configurations with M - MC_FREQ_RATIO=2, program this to JEDEC spec value divided by 2, and round it up to next integer value.*/ -#undef DDRC_INIT0_POST_CKE_X1024_DEFVAL -#undef DDRC_INIT0_POST_CKE_X1024_SHIFT -#undef DDRC_INIT0_POST_CKE_X1024_MASK -#define DDRC_INIT0_POST_CKE_X1024_DEFVAL 0x0002004E -#define DDRC_INIT0_POST_CKE_X1024_SHIFT 16 -#define DDRC_INIT0_POST_CKE_X1024_MASK 0x03FF0000U - -/*Cycles to wait after reset before driving CKE high to start the SDRAM initialization sequence. Unit: 1024 clock cycles. DDR2 - pecifications typically require this to be programmed for a delay of >= 200 us. LPDDR2/LPDDR3: tINIT1 of 100 ns (min) LPDDR4: - tINIT3 of 2 ms (min) For configurations with MEMC_FREQ_RATIO=2, program this to JEDEC spec value divided by 2, and round it u - to next integer value.*/ -#undef DDRC_INIT0_PRE_CKE_X1024_DEFVAL -#undef DDRC_INIT0_PRE_CKE_X1024_SHIFT -#undef DDRC_INIT0_PRE_CKE_X1024_MASK -#define DDRC_INIT0_PRE_CKE_X1024_DEFVAL 0x0002004E -#define DDRC_INIT0_PRE_CKE_X1024_SHIFT 0 -#define DDRC_INIT0_PRE_CKE_X1024_MASK 0x00000FFFU - -/*Number of cycles to assert SDRAM reset signal during init sequence. This is only present for designs supporting DDR3, DDR4 or - LPDDR4 devices. For use with a DDR PHY, this should be set to a minimum of 1*/ -#undef DDRC_INIT1_DRAM_RSTN_X1024_DEFVAL -#undef DDRC_INIT1_DRAM_RSTN_X1024_SHIFT -#undef DDRC_INIT1_DRAM_RSTN_X1024_MASK -#define DDRC_INIT1_DRAM_RSTN_X1024_DEFVAL 0x00000000 -#define DDRC_INIT1_DRAM_RSTN_X1024_SHIFT 16 -#define DDRC_INIT1_DRAM_RSTN_X1024_MASK 0x01FF0000U - -/*Cycles to wait after completing the SDRAM initialization sequence before starting the dynamic scheduler. Unit: Counts of a gl - bal timer that pulses every 32 clock cycles. There is no known specific requirement for this; it may be set to zero.*/ -#undef DDRC_INIT1_FINAL_WAIT_X32_DEFVAL -#undef DDRC_INIT1_FINAL_WAIT_X32_SHIFT -#undef DDRC_INIT1_FINAL_WAIT_X32_MASK -#define DDRC_INIT1_FINAL_WAIT_X32_DEFVAL 0x00000000 -#define DDRC_INIT1_FINAL_WAIT_X32_SHIFT 8 -#define DDRC_INIT1_FINAL_WAIT_X32_MASK 0x00007F00U - -/*Wait period before driving the OCD complete command to SDRAM. Unit: Counts of a global timer that pulses every 32 clock cycle - . There is no known specific requirement for this; it may be set to zero.*/ -#undef DDRC_INIT1_PRE_OCD_X32_DEFVAL -#undef DDRC_INIT1_PRE_OCD_X32_SHIFT -#undef DDRC_INIT1_PRE_OCD_X32_MASK -#define DDRC_INIT1_PRE_OCD_X32_DEFVAL 0x00000000 -#define DDRC_INIT1_PRE_OCD_X32_SHIFT 0 -#define DDRC_INIT1_PRE_OCD_X32_MASK 0x0000000FU - -/*Idle time after the reset command, tINIT4. Present only in designs configured to support LPDDR2. Unit: 32 clock cycles.*/ -#undef DDRC_INIT2_IDLE_AFTER_RESET_X32_DEFVAL -#undef DDRC_INIT2_IDLE_AFTER_RESET_X32_SHIFT -#undef DDRC_INIT2_IDLE_AFTER_RESET_X32_MASK -#define DDRC_INIT2_IDLE_AFTER_RESET_X32_DEFVAL 0x00000D05 -#define DDRC_INIT2_IDLE_AFTER_RESET_X32_SHIFT 8 -#define DDRC_INIT2_IDLE_AFTER_RESET_X32_MASK 0x0000FF00U - -/*Time to wait after the first CKE high, tINIT2. Present only in designs configured to support LPDDR2/LPDDR3. Unit: 1 clock cyc - e. LPDDR2/LPDDR3 typically requires 5 x tCK delay.*/ -#undef DDRC_INIT2_MIN_STABLE_CLOCK_X1_DEFVAL -#undef DDRC_INIT2_MIN_STABLE_CLOCK_X1_SHIFT -#undef DDRC_INIT2_MIN_STABLE_CLOCK_X1_MASK -#define DDRC_INIT2_MIN_STABLE_CLOCK_X1_DEFVAL 0x00000D05 -#define DDRC_INIT2_MIN_STABLE_CLOCK_X1_SHIFT 0 -#define DDRC_INIT2_MIN_STABLE_CLOCK_X1_MASK 0x0000000FU - -/*DDR2: Value to write to MR register. Bit 8 is for DLL and the setting here is ignored. The uMCTL2 sets this bit appropriately - DDR3/DDR4: Value loaded into MR0 register. mDDR: Value to write to MR register. LPDDR2/LPDDR3/LPDDR4 - Value to write to MR1 - register*/ -#undef DDRC_INIT3_MR_DEFVAL -#undef DDRC_INIT3_MR_SHIFT -#undef DDRC_INIT3_MR_MASK -#define DDRC_INIT3_MR_DEFVAL 0x00000510 -#define DDRC_INIT3_MR_SHIFT 16 -#define DDRC_INIT3_MR_MASK 0xFFFF0000U - -/*DDR2: Value to write to EMR register. Bits 9:7 are for OCD and the setting in this register is ignored. The uMCTL2 sets those - bits appropriately. DDR3/DDR4: Value to write to MR1 register Set bit 7 to 0. If PHY-evaluation mode training is enabled, thi - bit is set appropriately by the uMCTL2 during write leveling. mDDR: Value to write to EMR register. LPDDR2/LPDDR3/LPDDR4 - V - lue to write to MR2 register*/ -#undef DDRC_INIT3_EMR_DEFVAL -#undef DDRC_INIT3_EMR_SHIFT -#undef DDRC_INIT3_EMR_MASK -#define DDRC_INIT3_EMR_DEFVAL 0x00000510 -#define DDRC_INIT3_EMR_SHIFT 0 -#define DDRC_INIT3_EMR_MASK 0x0000FFFFU - -/*DDR2: Value to write to EMR2 register. DDR3/DDR4: Value to write to MR2 register LPDDR2/LPDDR3/LPDDR4: Value to write to MR3 - egister mDDR: Unused*/ -#undef DDRC_INIT4_EMR2_DEFVAL -#undef DDRC_INIT4_EMR2_SHIFT -#undef DDRC_INIT4_EMR2_MASK -#define DDRC_INIT4_EMR2_DEFVAL 0x00000000 -#define DDRC_INIT4_EMR2_SHIFT 16 -#define DDRC_INIT4_EMR2_MASK 0xFFFF0000U - -/*DDR2: Value to write to EMR3 register. DDR3/DDR4: Value to write to MR3 register mDDR/LPDDR2/LPDDR3: Unused LPDDR4: Value to - rite to MR13 register*/ -#undef DDRC_INIT4_EMR3_DEFVAL -#undef DDRC_INIT4_EMR3_SHIFT -#undef DDRC_INIT4_EMR3_MASK -#define DDRC_INIT4_EMR3_DEFVAL 0x00000000 -#define DDRC_INIT4_EMR3_SHIFT 0 -#define DDRC_INIT4_EMR3_MASK 0x0000FFFFU - -/*ZQ initial calibration, tZQINIT. Present only in designs configured to support DDR3 or DDR4 or LPDDR2/LPDDR3. Unit: 32 clock - ycles. DDR3 typically requires 512 clocks. DDR4 requires 1024 clocks. LPDDR2/LPDDR3 requires 1 us.*/ -#undef DDRC_INIT5_DEV_ZQINIT_X32_DEFVAL -#undef DDRC_INIT5_DEV_ZQINIT_X32_SHIFT -#undef DDRC_INIT5_DEV_ZQINIT_X32_MASK -#define DDRC_INIT5_DEV_ZQINIT_X32_DEFVAL 0x00100004 -#define DDRC_INIT5_DEV_ZQINIT_X32_SHIFT 16 -#define DDRC_INIT5_DEV_ZQINIT_X32_MASK 0x00FF0000U - -/*Maximum duration of the auto initialization, tINIT5. Present only in designs configured to support LPDDR2/LPDDR3. LPDDR2/LPDD - 3 typically requires 10 us.*/ -#undef DDRC_INIT5_MAX_AUTO_INIT_X1024_DEFVAL -#undef DDRC_INIT5_MAX_AUTO_INIT_X1024_SHIFT -#undef DDRC_INIT5_MAX_AUTO_INIT_X1024_MASK -#define DDRC_INIT5_MAX_AUTO_INIT_X1024_DEFVAL 0x00100004 -#define DDRC_INIT5_MAX_AUTO_INIT_X1024_SHIFT 0 -#define DDRC_INIT5_MAX_AUTO_INIT_X1024_MASK 0x000003FFU - -/*DDR4- Value to be loaded into SDRAM MR4 registers. Used in DDR4 designs only.*/ -#undef DDRC_INIT6_MR4_DEFVAL -#undef DDRC_INIT6_MR4_SHIFT -#undef DDRC_INIT6_MR4_MASK -#define DDRC_INIT6_MR4_DEFVAL 0x00000000 -#define DDRC_INIT6_MR4_SHIFT 16 -#define DDRC_INIT6_MR4_MASK 0xFFFF0000U - -/*DDR4- Value to be loaded into SDRAM MR5 registers. Used in DDR4 designs only.*/ -#undef DDRC_INIT6_MR5_DEFVAL -#undef DDRC_INIT6_MR5_SHIFT -#undef DDRC_INIT6_MR5_MASK -#define DDRC_INIT6_MR5_DEFVAL 0x00000000 -#define DDRC_INIT6_MR5_SHIFT 0 -#define DDRC_INIT6_MR5_MASK 0x0000FFFFU - -/*DDR4- Value to be loaded into SDRAM MR6 registers. Used in DDR4 designs only.*/ -#undef DDRC_INIT7_MR6_DEFVAL -#undef DDRC_INIT7_MR6_SHIFT -#undef DDRC_INIT7_MR6_MASK -#define DDRC_INIT7_MR6_DEFVAL -#define DDRC_INIT7_MR6_SHIFT 16 -#define DDRC_INIT7_MR6_MASK 0xFFFF0000U - -/*Disabling Address Mirroring for BG bits. When this is set to 1, BG0 and BG1 are NOT swapped even if Address Mirroring is enab - ed. This will be required for DDR4 DIMMs with x16 devices. - 1 - BG0 and BG1 are NOT swapped. - 0 - BG0 and BG1 are swapped i - address mirroring is enabled.*/ -#undef DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING_DEFVAL -#undef DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING_SHIFT -#undef DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING_MASK -#define DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING_DEFVAL 0x00000000 -#define DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING_SHIFT 5 -#define DDRC_DIMMCTL_DIMM_DIS_BG_MIRRORING_MASK 0x00000020U - -/*Enable for BG1 bit of MRS command. BG1 bit of the mode register address is specified as RFU (Reserved for Future Use) and mus - be programmed to 0 during MRS. In case where DRAMs which do not have BG1 are attached and both the CA parity and the Output - nversion are enabled, this must be set to 0, so that the calculation of CA parity will not include BG1 bit. Note: This has no - effect on the address of any other memory accesses, or of software-driven mode register accesses. If address mirroring is ena - led, this is applied to BG1 of even ranks and BG0 of odd ranks. - 1 - Enabled - 0 - Disabled*/ -#undef DDRC_DIMMCTL_MRS_BG1_EN_DEFVAL -#undef DDRC_DIMMCTL_MRS_BG1_EN_SHIFT -#undef DDRC_DIMMCTL_MRS_BG1_EN_MASK -#define DDRC_DIMMCTL_MRS_BG1_EN_DEFVAL 0x00000000 -#define DDRC_DIMMCTL_MRS_BG1_EN_SHIFT 4 -#define DDRC_DIMMCTL_MRS_BG1_EN_MASK 0x00000010U - -/*Enable for A17 bit of MRS command. A17 bit of the mode register address is specified as RFU (Reserved for Future Use) and mus - be programmed to 0 during MRS. In case where DRAMs which do not have A17 are attached and the Output Inversion are enabled, - his must be set to 0, so that the calculation of CA parity will not include A17 bit. Note: This has no effect on the address - f any other memory accesses, or of software-driven mode register accesses. - 1 - Enabled - 0 - Disabled*/ -#undef DDRC_DIMMCTL_MRS_A17_EN_DEFVAL -#undef DDRC_DIMMCTL_MRS_A17_EN_SHIFT -#undef DDRC_DIMMCTL_MRS_A17_EN_MASK -#define DDRC_DIMMCTL_MRS_A17_EN_DEFVAL 0x00000000 -#define DDRC_DIMMCTL_MRS_A17_EN_SHIFT 3 -#define DDRC_DIMMCTL_MRS_A17_EN_MASK 0x00000008U - -/*Output Inversion Enable (for DDR4 RDIMM implementations only). DDR4 RDIMM implements the Output Inversion feature by default, - which means that the following address, bank address and bank group bits of B-side DRAMs are inverted: A3-A9, A11, A13, A17, - A0-BA1, BG0-BG1. Setting this bit ensures that, for mode register accesses generated by the uMCTL2 during the automatic initi - lization routine and enabling of a particular DDR4 feature, separate A-side and B-side mode register accesses are generated. - or B-side mode register accesses, these bits are inverted within the uMCTL2 to compensate for this RDIMM inversion. Note: Thi - has no effect on the address of any other memory accesses, or of software-driven mode register accesses. - 1 - Implement out - ut inversion for B-side DRAMs. - 0 - Do not implement output inversion for B-side DRAMs.*/ -#undef DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN_DEFVAL -#undef DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN_SHIFT -#undef DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN_MASK -#define DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN_DEFVAL 0x00000000 -#define DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN_SHIFT 2 -#define DDRC_DIMMCTL_DIMM_OUTPUT_INV_EN_MASK 0x00000004U - -/*Address Mirroring Enable (for multi-rank UDIMM implementations and multi-rank DDR4 RDIMM implementations). Some UDIMMs and DD - 4 RDIMMs implement address mirroring for odd ranks, which means that the following address, bank address and bank group bits - re swapped: (A3, A4), (A5, A6), (A7, A8), (BA0, BA1) and also (A11, A13), (BG0, BG1) for the DDR4. Setting this bit ensures t - at, for mode register accesses during the automatic initialization routine, these bits are swapped within the uMCTL2 to compe - sate for this UDIMM/RDIMM swapping. In addition to the automatic initialization routine, in case of DDR4 UDIMM/RDIMM, they ar - swapped during the automatic MRS access to enable/disable of a particular DDR4 feature. Note: This has no effect on the addr - ss of any other memory accesses, or of software-driven mode register accesses. This is not supported for mDDR, LPDDR2, LPDDR3 - or LPDDR4 SDRAMs. Note: In case of x16 DDR4 DIMMs, BG1 output of MRS for the odd ranks is same as BG0 because BG1 is invalid, - hence dimm_dis_bg_mirroring register must be set to 1. - 1 - For odd ranks, implement address mirroring for MRS commands to d - ring initialization and for any automatic DDR4 MRS commands (to be used if UDIMM/RDIMM implements address mirroring) - 0 - Do - not implement address mirroring*/ -#undef DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN_DEFVAL -#undef DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN_SHIFT -#undef DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN_MASK -#define DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN_DEFVAL 0x00000000 -#define DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN_SHIFT 1 -#define DDRC_DIMMCTL_DIMM_ADDR_MIRR_EN_MASK 0x00000002U - -/*Staggering enable for multi-rank accesses (for multi-rank UDIMM and RDIMM implementations only). This is not supported for mD - R, LPDDR2, LPDDR3 or LPDDR4 SDRAMs. Note: Even if this bit is set it does not take care of software driven MR commands (via M - CTRL0/MRCTRL1), where software is responsible to send them to seperate ranks as appropriate. - 1 - (DDR4) Send MRS commands t - each ranks seperately - 1 - (non-DDR4) Send all commands to even and odd ranks seperately - 0 - Do not stagger accesses*/ -#undef DDRC_DIMMCTL_DIMM_STAGGER_CS_EN_DEFVAL -#undef DDRC_DIMMCTL_DIMM_STAGGER_CS_EN_SHIFT -#undef DDRC_DIMMCTL_DIMM_STAGGER_CS_EN_MASK -#define DDRC_DIMMCTL_DIMM_STAGGER_CS_EN_DEFVAL 0x00000000 -#define DDRC_DIMMCTL_DIMM_STAGGER_CS_EN_SHIFT 0 -#define DDRC_DIMMCTL_DIMM_STAGGER_CS_EN_MASK 0x00000001U - -/*Only present for multi-rank configurations. Indicates the number of clocks of gap in data responses when performing consecuti - e writes to different ranks. This is used to switch the delays in the PHY to match the rank requirements. This value should c - nsider both PHY requirement and ODT requirement. - PHY requirement: tphy_wrcsgap + 1 (see PHY databook for value of tphy_wrcs - ap) If CRC feature is enabled, should be increased by 1. If write preamble is set to 2tCK(DDR4/LPDDR4 only), should be increa - ed by 1. If write postamble is set to 1.5tCK(LPDDR4 only), should be increased by 1. - ODT requirement: The value programmed - n this register takes care of the ODT switch off timing requirement when switching ranks during writes. For LPDDR4, the requi - ement is ODTLoff - ODTLon - BL/2 + 1 For configurations with MEMC_FREQ_RATIO=1, program this to the larger of PHY requirement - or ODT requirement. For configurations with MEMC_FREQ_RATIO=2, program this to the larger value divided by two and round it u - to the next integer.*/ -#undef DDRC_RANKCTL_DIFF_RANK_WR_GAP_DEFVAL -#undef DDRC_RANKCTL_DIFF_RANK_WR_GAP_SHIFT -#undef DDRC_RANKCTL_DIFF_RANK_WR_GAP_MASK -#define DDRC_RANKCTL_DIFF_RANK_WR_GAP_DEFVAL 0x0000066F -#define DDRC_RANKCTL_DIFF_RANK_WR_GAP_SHIFT 8 -#define DDRC_RANKCTL_DIFF_RANK_WR_GAP_MASK 0x00000F00U - -/*Only present for multi-rank configurations. Indicates the number of clocks of gap in data responses when performing consecuti - e reads to different ranks. This is used to switch the delays in the PHY to match the rank requirements. This value should co - sider both PHY requirement and ODT requirement. - PHY requirement: tphy_rdcsgap + 1 (see PHY databook for value of tphy_rdcsg - p) If read preamble is set to 2tCK(DDR4/LPDDR4 only), should be increased by 1. If read postamble is set to 1.5tCK(LPDDR4 onl - ), should be increased by 1. - ODT requirement: The value programmed in this register takes care of the ODT switch off timing - requirement when switching ranks during reads. For configurations with MEMC_FREQ_RATIO=1, program this to the larger of PHY r - quirement or ODT requirement. For configurations with MEMC_FREQ_RATIO=2, program this to the larger value divided by two and - ound it up to the next integer.*/ -#undef DDRC_RANKCTL_DIFF_RANK_RD_GAP_DEFVAL -#undef DDRC_RANKCTL_DIFF_RANK_RD_GAP_SHIFT -#undef DDRC_RANKCTL_DIFF_RANK_RD_GAP_MASK -#define DDRC_RANKCTL_DIFF_RANK_RD_GAP_DEFVAL 0x0000066F -#define DDRC_RANKCTL_DIFF_RANK_RD_GAP_SHIFT 4 -#define DDRC_RANKCTL_DIFF_RANK_RD_GAP_MASK 0x000000F0U - -/*Only present for multi-rank configurations. Background: Reads to the same rank can be performed back-to-back. Reads to differ - nt ranks require additional gap dictated by the register RANKCTL.diff_rank_rd_gap. This is to avoid possible data bus content - on as well as to give PHY enough time to switch the delay when changing ranks. The uMCTL2 arbitrates for bus access on a cycl - -by-cycle basis; therefore after a read is scheduled, there are few clock cycles (determined by the value on RANKCTL.diff_ran - _rd_gap register) in which only reads from the same rank are eligible to be scheduled. This prevents reads from other ranks f - om having fair access to the data bus. This parameter represents the maximum number of reads that can be scheduled consecutiv - ly to the same rank. After this number is reached, a delay equal to RANKCTL.diff_rank_rd_gap is inserted by the scheduler to - llow all ranks a fair opportunity to be scheduled. Higher numbers increase bandwidth utilization, lower numbers increase fair - ess. This feature can be DISABLED by setting this register to 0. When set to 0, the Controller will stay on the same rank as - ong as commands are available for it. Minimum programmable value is 0 (feature disabled) and maximum programmable value is 0x - . FOR PERFORMANCE ONLY.*/ -#undef DDRC_RANKCTL_MAX_RANK_RD_DEFVAL -#undef DDRC_RANKCTL_MAX_RANK_RD_SHIFT -#undef DDRC_RANKCTL_MAX_RANK_RD_MASK -#define DDRC_RANKCTL_MAX_RANK_RD_DEFVAL 0x0000066F -#define DDRC_RANKCTL_MAX_RANK_RD_SHIFT 0 -#define DDRC_RANKCTL_MAX_RANK_RD_MASK 0x0000000FU - -/*Minimum time between write and precharge to same bank. Unit: Clocks Specifications: WL + BL/2 + tWR = approximately 8 cycles - 15 ns = 14 clocks @400MHz and less for lower frequencies where: - WL = write latency - BL = burst length. This must match th - value programmed in the BL bit of the mode register to the SDRAM. BST (burst terminate) is not supported at present. - tWR = - Write recovery time. This comes directly from the SDRAM specification. Add one extra cycle for LPDDR2/LPDDR3/LPDDR4 for this - arameter. For configurations with MEMC_FREQ_RATIO=2, 1T mode, divide the above value by 2. No rounding up. For configurations - with MEMC_FREQ_RATIO=2, 2T mode or LPDDR4 mode, divide the above value by 2 and round it up to the next integer value.*/ -#undef DDRC_DRAMTMG0_WR2PRE_DEFVAL -#undef DDRC_DRAMTMG0_WR2PRE_SHIFT -#undef DDRC_DRAMTMG0_WR2PRE_MASK -#define DDRC_DRAMTMG0_WR2PRE_DEFVAL 0x0F101B0F -#define DDRC_DRAMTMG0_WR2PRE_SHIFT 24 -#define DDRC_DRAMTMG0_WR2PRE_MASK 0x7F000000U - -/*tFAW Valid only when 8 or more banks(or banks x bank groups) are present. In 8-bank design, at most 4 banks must be activated - in a rolling window of tFAW cycles. For configurations with MEMC_FREQ_RATIO=2, program this to (tFAW/2) and round up to next - nteger value. In a 4-bank design, set this register to 0x1 independent of the MEMC_FREQ_RATIO configuration. Unit: Clocks*/ -#undef DDRC_DRAMTMG0_T_FAW_DEFVAL -#undef DDRC_DRAMTMG0_T_FAW_SHIFT -#undef DDRC_DRAMTMG0_T_FAW_MASK -#define DDRC_DRAMTMG0_T_FAW_DEFVAL 0x0F101B0F -#define DDRC_DRAMTMG0_T_FAW_SHIFT 16 -#define DDRC_DRAMTMG0_T_FAW_MASK 0x003F0000U - -/*tRAS(max): Maximum time between activate and precharge to same bank. This is the maximum time that a page can be kept open Mi - imum value of this register is 1. Zero is invalid. For configurations with MEMC_FREQ_RATIO=2, program this to (tRAS(max)-1)/2 - No rounding up. Unit: Multiples of 1024 clocks.*/ -#undef DDRC_DRAMTMG0_T_RAS_MAX_DEFVAL -#undef DDRC_DRAMTMG0_T_RAS_MAX_SHIFT -#undef DDRC_DRAMTMG0_T_RAS_MAX_MASK -#define DDRC_DRAMTMG0_T_RAS_MAX_DEFVAL 0x0F101B0F -#define DDRC_DRAMTMG0_T_RAS_MAX_SHIFT 8 -#define DDRC_DRAMTMG0_T_RAS_MAX_MASK 0x00007F00U - -/*tRAS(min): Minimum time between activate and precharge to the same bank. For configurations with MEMC_FREQ_RATIO=2, 1T mode, - rogram this to tRAS(min)/2. No rounding up. For configurations with MEMC_FREQ_RATIO=2, 2T mode or LPDDR4 mode, program this t - (tRAS(min)/2) and round it up to the next integer value. Unit: Clocks*/ -#undef DDRC_DRAMTMG0_T_RAS_MIN_DEFVAL -#undef DDRC_DRAMTMG0_T_RAS_MIN_SHIFT -#undef DDRC_DRAMTMG0_T_RAS_MIN_MASK -#define DDRC_DRAMTMG0_T_RAS_MIN_DEFVAL 0x0F101B0F -#define DDRC_DRAMTMG0_T_RAS_MIN_SHIFT 0 -#define DDRC_DRAMTMG0_T_RAS_MIN_MASK 0x0000003FU - -/*tXP: Minimum time after power-down exit to any operation. For DDR3, this should be programmed to tXPDLL if slow powerdown exi - is selected in MR0[12]. If C/A parity for DDR4 is used, set to (tXP+PL) instead. For configurations with MEMC_FREQ_RATIO=2, - rogram this to (tXP/2) and round it up to the next integer value. Units: Clocks*/ -#undef DDRC_DRAMTMG1_T_XP_DEFVAL -#undef DDRC_DRAMTMG1_T_XP_SHIFT -#undef DDRC_DRAMTMG1_T_XP_MASK -#define DDRC_DRAMTMG1_T_XP_DEFVAL 0x00080414 -#define DDRC_DRAMTMG1_T_XP_SHIFT 16 -#define DDRC_DRAMTMG1_T_XP_MASK 0x001F0000U - -/*tRTP: Minimum time from read to precharge of same bank. - DDR2: tAL + BL/2 + max(tRTP, 2) - 2 - DDR3: tAL + max (tRTP, 4) - D - R4: Max of following two equations: tAL + max (tRTP, 4) or, RL + BL/2 - tRP. - mDDR: BL/2 - LPDDR2: Depends on if it's LPDDR2 - S2 or LPDDR2-S4: LPDDR2-S2: BL/2 + tRTP - 1. LPDDR2-S4: BL/2 + max(tRTP,2) - 2. - LPDDR3: BL/2 + max(tRTP,4) - 4 - LPDDR4: BL - 2 + max(tRTP,8) - 8 For configurations with MEMC_FREQ_RATIO=2, 1T mode, divide the above value by 2. No rounding up. For conf - gurations with MEMC_FREQ_RATIO=2, 2T mode or LPDDR4 mode, divide the above value by 2 and round it up to the next integer val - e. Unit: Clocks.*/ -#undef DDRC_DRAMTMG1_RD2PRE_DEFVAL -#undef DDRC_DRAMTMG1_RD2PRE_SHIFT -#undef DDRC_DRAMTMG1_RD2PRE_MASK -#define DDRC_DRAMTMG1_RD2PRE_DEFVAL 0x00080414 -#define DDRC_DRAMTMG1_RD2PRE_SHIFT 8 -#define DDRC_DRAMTMG1_RD2PRE_MASK 0x00001F00U - -/*tRC: Minimum time between activates to same bank. For configurations with MEMC_FREQ_RATIO=2, program this to (tRC/2) and roun - up to next integer value. Unit: Clocks.*/ -#undef DDRC_DRAMTMG1_T_RC_DEFVAL -#undef DDRC_DRAMTMG1_T_RC_SHIFT -#undef DDRC_DRAMTMG1_T_RC_MASK -#define DDRC_DRAMTMG1_T_RC_DEFVAL 0x00080414 -#define DDRC_DRAMTMG1_T_RC_SHIFT 0 -#define DDRC_DRAMTMG1_T_RC_MASK 0x0000007FU - -/*Set to WL Time from write command to write data on SDRAM interface. This must be set to WL. For mDDR, it should normally be s - t to 1. Note that, depending on the PHY, if using RDIMM, it may be necessary to use a value of WL + 1 to compensate for the e - tra cycle of latency through the RDIMM For configurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above - equation by 2, and round it up to next integer. This register field is not required for DDR2 and DDR3 (except if MEMC_TRAININ - is set), as the DFI read and write latencies defined in DFITMG0 and DFITMG1 are sufficient for those protocols Unit: clocks*/ -#undef DDRC_DRAMTMG2_WRITE_LATENCY_DEFVAL -#undef DDRC_DRAMTMG2_WRITE_LATENCY_SHIFT -#undef DDRC_DRAMTMG2_WRITE_LATENCY_MASK -#define DDRC_DRAMTMG2_WRITE_LATENCY_DEFVAL 0x0305060D -#define DDRC_DRAMTMG2_WRITE_LATENCY_SHIFT 24 -#define DDRC_DRAMTMG2_WRITE_LATENCY_MASK 0x3F000000U - -/*Set to RL Time from read command to read data on SDRAM interface. This must be set to RL. Note that, depending on the PHY, if - using RDIMM, it mat be necessary to use a value of RL + 1 to compensate for the extra cycle of latency through the RDIMM For - onfigurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next inte - er. This register field is not required for DDR2 and DDR3 (except if MEMC_TRAINING is set), as the DFI read and write latenci - s defined in DFITMG0 and DFITMG1 are sufficient for those protocols Unit: clocks*/ -#undef DDRC_DRAMTMG2_READ_LATENCY_DEFVAL -#undef DDRC_DRAMTMG2_READ_LATENCY_SHIFT -#undef DDRC_DRAMTMG2_READ_LATENCY_MASK -#define DDRC_DRAMTMG2_READ_LATENCY_DEFVAL 0x0305060D -#define DDRC_DRAMTMG2_READ_LATENCY_SHIFT 16 -#define DDRC_DRAMTMG2_READ_LATENCY_MASK 0x003F0000U - -/*DDR2/3/mDDR: RL + BL/2 + 2 - WL DDR4: RL + BL/2 + 1 + WR_PREAMBLE - WL LPDDR2/LPDDR3: RL + BL/2 + RU(tDQSCKmax/tCK) + 1 - WL - PDDR4(DQ ODT is Disabled): RL + BL/2 + RU(tDQSCKmax/tCK) + WR_PREAMBLE + RD_POSTAMBLE - WL LPDDR4(DQ ODT is Enabled) : RL + B - /2 + RU(tDQSCKmax/tCK) + RD_POSTAMBLE - ODTLon - RU(tODTon(min)/tCK) Minimum time from read command to write command. Include - time for bus turnaround and all per-bank, per-rank, and global constraints. Unit: Clocks. Where: - WL = write latency - BL = - urst length. This must match the value programmed in the BL bit of the mode register to the SDRAM - RL = read latency = CAS l - tency - WR_PREAMBLE = write preamble. This is unique to DDR4 and LPDDR4. - RD_POSTAMBLE = read postamble. This is unique to L - DDR4. For LPDDR2/LPDDR3/LPDDR4, if derating is enabled (DERATEEN.derate_enable=1), derated tDQSCKmax should be used. For conf - gurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next integer.*/ -#undef DDRC_DRAMTMG2_RD2WR_DEFVAL -#undef DDRC_DRAMTMG2_RD2WR_SHIFT -#undef DDRC_DRAMTMG2_RD2WR_MASK -#define DDRC_DRAMTMG2_RD2WR_DEFVAL 0x0305060D -#define DDRC_DRAMTMG2_RD2WR_SHIFT 8 -#define DDRC_DRAMTMG2_RD2WR_MASK 0x00003F00U - -/*DDR4: CWL + PL + BL/2 + tWTR_L Others: CWL + BL/2 + tWTR In DDR4, minimum time from write command to read command for same ba - k group. In others, minimum time from write command to read command. Includes time for bus turnaround, recovery times, and al - per-bank, per-rank, and global constraints. Unit: Clocks. Where: - CWL = CAS write latency - PL = Parity latency - BL = burs - length. This must match the value programmed in the BL bit of the mode register to the SDRAM - tWTR_L = internal write to re - d command delay for same bank group. This comes directly from the SDRAM specification. - tWTR = internal write to read comman - delay. This comes directly from the SDRAM specification. Add one extra cycle for LPDDR2/LPDDR3/LPDDR4 operation. For configu - ations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next integer.*/ -#undef DDRC_DRAMTMG2_WR2RD_DEFVAL -#undef DDRC_DRAMTMG2_WR2RD_SHIFT -#undef DDRC_DRAMTMG2_WR2RD_MASK -#define DDRC_DRAMTMG2_WR2RD_DEFVAL 0x0305060D -#define DDRC_DRAMTMG2_WR2RD_SHIFT 0 -#define DDRC_DRAMTMG2_WR2RD_MASK 0x0000003FU - -/*Time to wait after a mode register write or read (MRW or MRR). Present only in designs configured to support LPDDR2, LPDDR3 o - LPDDR4. LPDDR2 typically requires value of 5. LPDDR3 typically requires value of 10. LPDDR4: Set this to the larger of tMRW - nd tMRWCKEL. For LPDDR2, this register is used for the time from a MRW/MRR to all other commands. For LDPDR3, this register i - used for the time from a MRW/MRR to a MRW/MRR.*/ -#undef DDRC_DRAMTMG3_T_MRW_DEFVAL -#undef DDRC_DRAMTMG3_T_MRW_SHIFT -#undef DDRC_DRAMTMG3_T_MRW_MASK -#define DDRC_DRAMTMG3_T_MRW_DEFVAL 0x0050400C -#define DDRC_DRAMTMG3_T_MRW_SHIFT 20 -#define DDRC_DRAMTMG3_T_MRW_MASK 0x3FF00000U - -/*tMRD: Cycles to wait after a mode register write or read. Depending on the connected SDRAM, tMRD represents: DDR2/mDDR: Time - rom MRS to any command DDR3/4: Time from MRS to MRS command LPDDR2: not used LPDDR3/4: Time from MRS to non-MRS command For c - nfigurations with MEMC_FREQ_RATIO=2, program this to (tMRD/2) and round it up to the next integer value. If C/A parity for DD - 4 is used, set to tMRD_PAR(tMOD+PL) instead.*/ -#undef DDRC_DRAMTMG3_T_MRD_DEFVAL -#undef DDRC_DRAMTMG3_T_MRD_SHIFT -#undef DDRC_DRAMTMG3_T_MRD_MASK -#define DDRC_DRAMTMG3_T_MRD_DEFVAL 0x0050400C -#define DDRC_DRAMTMG3_T_MRD_SHIFT 12 -#define DDRC_DRAMTMG3_T_MRD_MASK 0x0003F000U - -/*tMOD: Parameter used only in DDR3 and DDR4. Cycles between load mode command and following non-load mode command. If C/A pari - y for DDR4 is used, set to tMOD_PAR(tMOD+PL) instead. Set to tMOD if MEMC_FREQ_RATIO=1, or tMOD/2 (rounded up to next integer - if MEMC_FREQ_RATIO=2. Note that if using RDIMM, depending on the PHY, it may be necessary to use a value of tMOD + 1 or (tMO - + 1)/2 to compensate for the extra cycle of latency applied to mode register writes by the RDIMM chip.*/ -#undef DDRC_DRAMTMG3_T_MOD_DEFVAL -#undef DDRC_DRAMTMG3_T_MOD_SHIFT -#undef DDRC_DRAMTMG3_T_MOD_MASK -#define DDRC_DRAMTMG3_T_MOD_DEFVAL 0x0050400C -#define DDRC_DRAMTMG3_T_MOD_SHIFT 0 -#define DDRC_DRAMTMG3_T_MOD_MASK 0x000003FFU - -/*tRCD - tAL: Minimum time from activate to read or write command to same bank. For configurations with MEMC_FREQ_RATIO=2, prog - am this to ((tRCD - tAL)/2) and round it up to the next integer value. Minimum value allowed for this register is 1, which im - lies minimum (tRCD - tAL) value to be 2 in configurations with MEMC_FREQ_RATIO=2. Unit: Clocks.*/ -#undef DDRC_DRAMTMG4_T_RCD_DEFVAL -#undef DDRC_DRAMTMG4_T_RCD_SHIFT -#undef DDRC_DRAMTMG4_T_RCD_MASK -#define DDRC_DRAMTMG4_T_RCD_DEFVAL 0x05040405 -#define DDRC_DRAMTMG4_T_RCD_SHIFT 24 -#define DDRC_DRAMTMG4_T_RCD_MASK 0x1F000000U - -/*DDR4: tCCD_L: This is the minimum time between two reads or two writes for same bank group. Others: tCCD: This is the minimum - time between two reads or two writes. For configurations with MEMC_FREQ_RATIO=2, program this to (tCCD_L/2 or tCCD/2) and rou - d it up to the next integer value. Unit: clocks.*/ -#undef DDRC_DRAMTMG4_T_CCD_DEFVAL -#undef DDRC_DRAMTMG4_T_CCD_SHIFT -#undef DDRC_DRAMTMG4_T_CCD_MASK -#define DDRC_DRAMTMG4_T_CCD_DEFVAL 0x05040405 -#define DDRC_DRAMTMG4_T_CCD_SHIFT 16 -#define DDRC_DRAMTMG4_T_CCD_MASK 0x000F0000U - -/*DDR4: tRRD_L: Minimum time between activates from bank 'a' to bank 'b' for same bank group. Others: tRRD: Minimum time betwee - activates from bank 'a' to bank 'b'For configurations with MEMC_FREQ_RATIO=2, program this to (tRRD_L/2 or tRRD/2) and round - it up to the next integer value. Unit: Clocks.*/ -#undef DDRC_DRAMTMG4_T_RRD_DEFVAL -#undef DDRC_DRAMTMG4_T_RRD_SHIFT -#undef DDRC_DRAMTMG4_T_RRD_MASK -#define DDRC_DRAMTMG4_T_RRD_DEFVAL 0x05040405 -#define DDRC_DRAMTMG4_T_RRD_SHIFT 8 -#define DDRC_DRAMTMG4_T_RRD_MASK 0x00000F00U - -/*tRP: Minimum time from precharge to activate of same bank. For MEMC_FREQ_RATIO=1 configurations, t_rp should be set to RoundU - (tRP/tCK). For MEMC_FREQ_RATIO=2 configurations, t_rp should be set to RoundDown(RoundUp(tRP/tCK)/2) + 1. For MEMC_FREQ_RATIO - 2 configurations in LPDDR4, t_rp should be set to RoundUp(RoundUp(tRP/tCK)/2). Unit: Clocks.*/ -#undef DDRC_DRAMTMG4_T_RP_DEFVAL -#undef DDRC_DRAMTMG4_T_RP_SHIFT -#undef DDRC_DRAMTMG4_T_RP_MASK -#define DDRC_DRAMTMG4_T_RP_DEFVAL 0x05040405 -#define DDRC_DRAMTMG4_T_RP_SHIFT 0 -#define DDRC_DRAMTMG4_T_RP_MASK 0x0000001FU - -/*This is the time before Self Refresh Exit that CK is maintained as a valid clock before issuing SRX. Specifies the clock stab - e time before SRX. Recommended settings: - mDDR: 1 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEH - DDR2: 1 - DDR3: tCKSRX - DDR4: - tCKSRX For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it up to next in - eger.*/ -#undef DDRC_DRAMTMG5_T_CKSRX_DEFVAL -#undef DDRC_DRAMTMG5_T_CKSRX_SHIFT -#undef DDRC_DRAMTMG5_T_CKSRX_MASK -#define DDRC_DRAMTMG5_T_CKSRX_DEFVAL 0x05050403 -#define DDRC_DRAMTMG5_T_CKSRX_SHIFT 24 -#define DDRC_DRAMTMG5_T_CKSRX_MASK 0x0F000000U - -/*This is the time after Self Refresh Down Entry that CK is maintained as a valid clock. Specifies the clock disable delay afte - SRE. Recommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEL - DDR2: 1 - DDR3: max (10 ns, 5 tCK) - DDR4: - ax (10 ns, 5 tCK) For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it up - to next integer.*/ -#undef DDRC_DRAMTMG5_T_CKSRE_DEFVAL -#undef DDRC_DRAMTMG5_T_CKSRE_SHIFT -#undef DDRC_DRAMTMG5_T_CKSRE_MASK -#define DDRC_DRAMTMG5_T_CKSRE_DEFVAL 0x05050403 -#define DDRC_DRAMTMG5_T_CKSRE_SHIFT 16 -#define DDRC_DRAMTMG5_T_CKSRE_MASK 0x000F0000U - -/*Minimum CKE low width for Self refresh or Self refresh power down entry to exit timing in memory clock cycles. Recommended se - tings: - mDDR: tRFC - LPDDR2: tCKESR - LPDDR3: tCKESR - LPDDR4: max(tCKELPD, tSR) - DDR2: tCKE - DDR3: tCKE + 1 - DDR4: tCKE - 1 For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it up to next intege - .*/ -#undef DDRC_DRAMTMG5_T_CKESR_DEFVAL -#undef DDRC_DRAMTMG5_T_CKESR_SHIFT -#undef DDRC_DRAMTMG5_T_CKESR_MASK -#define DDRC_DRAMTMG5_T_CKESR_DEFVAL 0x05050403 -#define DDRC_DRAMTMG5_T_CKESR_SHIFT 8 -#define DDRC_DRAMTMG5_T_CKESR_MASK 0x00003F00U - -/*Minimum number of cycles of CKE HIGH/LOW during power-down and self refresh. - LPDDR2/LPDDR3 mode: Set this to the larger of - CKE or tCKESR - LPDDR4 mode: Set this to the larger of tCKE, tCKELPD or tSR. - Non-LPDDR2/non-LPDDR3/non-LPDDR4 designs: Set - his to tCKE value. For configurations with MEMC_FREQ_RATIO=2, program this to (value described above)/2 and round it up to th - next integer value. Unit: Clocks.*/ -#undef DDRC_DRAMTMG5_T_CKE_DEFVAL -#undef DDRC_DRAMTMG5_T_CKE_SHIFT -#undef DDRC_DRAMTMG5_T_CKE_MASK -#define DDRC_DRAMTMG5_T_CKE_DEFVAL 0x05050403 -#define DDRC_DRAMTMG5_T_CKE_SHIFT 0 -#define DDRC_DRAMTMG5_T_CKE_MASK 0x0000001FU - -/*This is the time after Deep Power Down Entry that CK is maintained as a valid clock. Specifies the clock disable delay after - PDE. Recommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 For configurations with MEMC_FREQ_RATIO=2, program this to recom - ended value divided by two and round it up to next integer. This is only present for designs supporting mDDR or LPDDR2/LPDDR3 - devices.*/ -#undef DDRC_DRAMTMG6_T_CKDPDE_DEFVAL -#undef DDRC_DRAMTMG6_T_CKDPDE_SHIFT -#undef DDRC_DRAMTMG6_T_CKDPDE_MASK -#define DDRC_DRAMTMG6_T_CKDPDE_DEFVAL 0x02020005 -#define DDRC_DRAMTMG6_T_CKDPDE_SHIFT 24 -#define DDRC_DRAMTMG6_T_CKDPDE_MASK 0x0F000000U - -/*This is the time before Deep Power Down Exit that CK is maintained as a valid clock before issuing DPDX. Specifies the clock - table time before DPDX. Recommended settings: - mDDR: 1 - LPDDR2: 2 - LPDDR3: 2 For configurations with MEMC_FREQ_RATIO=2, pr - gram this to recommended value divided by two and round it up to next integer. This is only present for designs supporting mD - R or LPDDR2 devices.*/ -#undef DDRC_DRAMTMG6_T_CKDPDX_DEFVAL -#undef DDRC_DRAMTMG6_T_CKDPDX_SHIFT -#undef DDRC_DRAMTMG6_T_CKDPDX_MASK -#define DDRC_DRAMTMG6_T_CKDPDX_DEFVAL 0x02020005 -#define DDRC_DRAMTMG6_T_CKDPDX_SHIFT 16 -#define DDRC_DRAMTMG6_T_CKDPDX_MASK 0x000F0000U - -/*This is the time before Clock Stop Exit that CK is maintained as a valid clock before issuing Clock Stop Exit. Specifies the - lock stable time before next command after Clock Stop Exit. Recommended settings: - mDDR: 1 - LPDDR2: tXP + 2 - LPDDR3: tXP + - 2 - LPDDR4: tXP + 2 For configurations with MEMC_FREQ_RATIO=2, program this to recommended value divided by two and round it - p to next integer. This is only present for designs supporting mDDR or LPDDR2/LPDDR3/LPDDR4 devices.*/ -#undef DDRC_DRAMTMG6_T_CKCSX_DEFVAL -#undef DDRC_DRAMTMG6_T_CKCSX_SHIFT -#undef DDRC_DRAMTMG6_T_CKCSX_MASK -#define DDRC_DRAMTMG6_T_CKCSX_DEFVAL 0x02020005 -#define DDRC_DRAMTMG6_T_CKCSX_SHIFT 0 -#define DDRC_DRAMTMG6_T_CKCSX_MASK 0x0000000FU - -/*This is the time after Power Down Entry that CK is maintained as a valid clock. Specifies the clock disable delay after PDE. - ecommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: tCKCKEL For configurations with MEMC_FREQ_RATIO=2, program t - is to recommended value divided by two and round it up to next integer. This is only present for designs supporting mDDR or L - DDR2/LPDDR3/LPDDR4 devices.*/ -#undef DDRC_DRAMTMG7_T_CKPDE_DEFVAL -#undef DDRC_DRAMTMG7_T_CKPDE_SHIFT -#undef DDRC_DRAMTMG7_T_CKPDE_MASK -#define DDRC_DRAMTMG7_T_CKPDE_DEFVAL 0x00000202 -#define DDRC_DRAMTMG7_T_CKPDE_SHIFT 8 -#define DDRC_DRAMTMG7_T_CKPDE_MASK 0x00000F00U - -/*This is the time before Power Down Exit that CK is maintained as a valid clock before issuing PDX. Specifies the clock stable - time before PDX. Recommended settings: - mDDR: 0 - LPDDR2: 2 - LPDDR3: 2 - LPDDR4: 2 For configurations with MEMC_FREQ_RATIO= - , program this to recommended value divided by two and round it up to next integer. This is only present for designs supporti - g mDDR or LPDDR2/LPDDR3/LPDDR4 devices.*/ -#undef DDRC_DRAMTMG7_T_CKPDX_DEFVAL -#undef DDRC_DRAMTMG7_T_CKPDX_SHIFT -#undef DDRC_DRAMTMG7_T_CKPDX_MASK -#define DDRC_DRAMTMG7_T_CKPDX_DEFVAL 0x00000202 -#define DDRC_DRAMTMG7_T_CKPDX_SHIFT 0 -#define DDRC_DRAMTMG7_T_CKPDX_MASK 0x0000000FU - -/*tXS_FAST: Exit Self Refresh to ZQCL, ZQCS and MRS (only CL, WR, RTP and Geardown mode). For configurations with MEMC_FREQ_RAT - O=2, program this to the above value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: Thi - is applicable to only ZQCL/ZQCS commands. Note: Ensure this is less than or equal to t_xs_x32.*/ -#undef DDRC_DRAMTMG8_T_XS_FAST_X32_DEFVAL -#undef DDRC_DRAMTMG8_T_XS_FAST_X32_SHIFT -#undef DDRC_DRAMTMG8_T_XS_FAST_X32_MASK -#define DDRC_DRAMTMG8_T_XS_FAST_X32_DEFVAL 0x03034405 -#define DDRC_DRAMTMG8_T_XS_FAST_X32_SHIFT 24 -#define DDRC_DRAMTMG8_T_XS_FAST_X32_MASK 0x7F000000U - -/*tXS_ABORT: Exit Self Refresh to commands not requiring a locked DLL in Self Refresh Abort. For configurations with MEMC_FREQ_ - ATIO=2, program this to the above value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: - nsure this is less than or equal to t_xs_x32.*/ -#undef DDRC_DRAMTMG8_T_XS_ABORT_X32_DEFVAL -#undef DDRC_DRAMTMG8_T_XS_ABORT_X32_SHIFT -#undef DDRC_DRAMTMG8_T_XS_ABORT_X32_MASK -#define DDRC_DRAMTMG8_T_XS_ABORT_X32_DEFVAL 0x03034405 -#define DDRC_DRAMTMG8_T_XS_ABORT_X32_SHIFT 16 -#define DDRC_DRAMTMG8_T_XS_ABORT_X32_MASK 0x007F0000U - -/*tXSDLL: Exit Self Refresh to commands requiring a locked DLL. For configurations with MEMC_FREQ_RATIO=2, program this to the - bove value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: Used only for DDR2, DDR3 and - DR4 SDRAMs.*/ -#undef DDRC_DRAMTMG8_T_XS_DLL_X32_DEFVAL -#undef DDRC_DRAMTMG8_T_XS_DLL_X32_SHIFT -#undef DDRC_DRAMTMG8_T_XS_DLL_X32_MASK -#define DDRC_DRAMTMG8_T_XS_DLL_X32_DEFVAL 0x03034405 -#define DDRC_DRAMTMG8_T_XS_DLL_X32_SHIFT 8 -#define DDRC_DRAMTMG8_T_XS_DLL_X32_MASK 0x00007F00U - -/*tXS: Exit Self Refresh to commands not requiring a locked DLL. For configurations with MEMC_FREQ_RATIO=2, program this to the - above value divided by 2 and round up to next integer value. Unit: Multiples of 32 clocks. Note: Used only for DDR2, DDR3 and - DDR4 SDRAMs.*/ -#undef DDRC_DRAMTMG8_T_XS_X32_DEFVAL -#undef DDRC_DRAMTMG8_T_XS_X32_SHIFT -#undef DDRC_DRAMTMG8_T_XS_X32_MASK -#define DDRC_DRAMTMG8_T_XS_X32_DEFVAL 0x03034405 -#define DDRC_DRAMTMG8_T_XS_X32_SHIFT 0 -#define DDRC_DRAMTMG8_T_XS_X32_MASK 0x0000007FU - -/*DDR4 Write preamble mode - 0: 1tCK preamble - 1: 2tCK preamble Present only with MEMC_FREQ_RATIO=2*/ -#undef DDRC_DRAMTMG9_DDR4_WR_PREAMBLE_DEFVAL -#undef DDRC_DRAMTMG9_DDR4_WR_PREAMBLE_SHIFT -#undef DDRC_DRAMTMG9_DDR4_WR_PREAMBLE_MASK -#define DDRC_DRAMTMG9_DDR4_WR_PREAMBLE_DEFVAL 0x0004040D -#define DDRC_DRAMTMG9_DDR4_WR_PREAMBLE_SHIFT 30 -#define DDRC_DRAMTMG9_DDR4_WR_PREAMBLE_MASK 0x40000000U - -/*tCCD_S: This is the minimum time between two reads or two writes for different bank group. For bank switching (from bank 'a' - o bank 'b'), the minimum time is this value + 1. For configurations with MEMC_FREQ_RATIO=2, program this to (tCCD_S/2) and ro - nd it up to the next integer value. Present only in designs configured to support DDR4. Unit: clocks.*/ -#undef DDRC_DRAMTMG9_T_CCD_S_DEFVAL -#undef DDRC_DRAMTMG9_T_CCD_S_SHIFT -#undef DDRC_DRAMTMG9_T_CCD_S_MASK -#define DDRC_DRAMTMG9_T_CCD_S_DEFVAL 0x0004040D -#define DDRC_DRAMTMG9_T_CCD_S_SHIFT 16 -#define DDRC_DRAMTMG9_T_CCD_S_MASK 0x00070000U - -/*tRRD_S: Minimum time between activates from bank 'a' to bank 'b' for different bank group. For configurations with MEMC_FREQ_ - ATIO=2, program this to (tRRD_S/2) and round it up to the next integer value. Present only in designs configured to support D - R4. Unit: Clocks.*/ -#undef DDRC_DRAMTMG9_T_RRD_S_DEFVAL -#undef DDRC_DRAMTMG9_T_RRD_S_SHIFT -#undef DDRC_DRAMTMG9_T_RRD_S_MASK -#define DDRC_DRAMTMG9_T_RRD_S_DEFVAL 0x0004040D -#define DDRC_DRAMTMG9_T_RRD_S_SHIFT 8 -#define DDRC_DRAMTMG9_T_RRD_S_MASK 0x00000F00U - -/*CWL + PL + BL/2 + tWTR_S Minimum time from write command to read command for different bank group. Includes time for bus turn - round, recovery times, and all per-bank, per-rank, and global constraints. Present only in designs configured to support DDR4 - Unit: Clocks. Where: - CWL = CAS write latency - PL = Parity latency - BL = burst length. This must match the value programm - d in the BL bit of the mode register to the SDRAM - tWTR_S = internal write to read command delay for different bank group. T - is comes directly from the SDRAM specification. For configurations with MEMC_FREQ_RATIO=2, divide the value calculated using - he above equation by 2, and round it up to next integer.*/ -#undef DDRC_DRAMTMG9_WR2RD_S_DEFVAL -#undef DDRC_DRAMTMG9_WR2RD_S_SHIFT -#undef DDRC_DRAMTMG9_WR2RD_S_MASK -#define DDRC_DRAMTMG9_WR2RD_S_DEFVAL 0x0004040D -#define DDRC_DRAMTMG9_WR2RD_S_SHIFT 0 -#define DDRC_DRAMTMG9_WR2RD_S_MASK 0x0000003FU - -/*tXMPDLL: This is the minimum Exit MPSM to commands requiring a locked DLL. For configurations with MEMC_FREQ_RATIO=2, program - this to (tXMPDLL/2) and round it up to the next integer value. Present only in designs configured to support DDR4. Unit: Mult - ples of 32 clocks.*/ -#undef DDRC_DRAMTMG11_POST_MPSM_GAP_X32_DEFVAL -#undef DDRC_DRAMTMG11_POST_MPSM_GAP_X32_SHIFT -#undef DDRC_DRAMTMG11_POST_MPSM_GAP_X32_MASK -#define DDRC_DRAMTMG11_POST_MPSM_GAP_X32_DEFVAL 0x440C021C -#define DDRC_DRAMTMG11_POST_MPSM_GAP_X32_SHIFT 24 -#define DDRC_DRAMTMG11_POST_MPSM_GAP_X32_MASK 0x7F000000U - -/*tMPX_LH: This is the minimum CS_n Low hold time to CKE rising edge. For configurations with MEMC_FREQ_RATIO=2, program this t - RoundUp(tMPX_LH/2)+1. Present only in designs configured to support DDR4. Unit: clocks.*/ -#undef DDRC_DRAMTMG11_T_MPX_LH_DEFVAL -#undef DDRC_DRAMTMG11_T_MPX_LH_SHIFT -#undef DDRC_DRAMTMG11_T_MPX_LH_MASK -#define DDRC_DRAMTMG11_T_MPX_LH_DEFVAL 0x440C021C -#define DDRC_DRAMTMG11_T_MPX_LH_SHIFT 16 -#define DDRC_DRAMTMG11_T_MPX_LH_MASK 0x001F0000U - -/*tMPX_S: Minimum time CS setup time to CKE. For configurations with MEMC_FREQ_RATIO=2, program this to (tMPX_S/2) and round it - up to the next integer value. Present only in designs configured to support DDR4. Unit: Clocks.*/ -#undef DDRC_DRAMTMG11_T_MPX_S_DEFVAL -#undef DDRC_DRAMTMG11_T_MPX_S_SHIFT -#undef DDRC_DRAMTMG11_T_MPX_S_MASK -#define DDRC_DRAMTMG11_T_MPX_S_DEFVAL 0x440C021C -#define DDRC_DRAMTMG11_T_MPX_S_SHIFT 8 -#define DDRC_DRAMTMG11_T_MPX_S_MASK 0x00000300U - -/*tCKMPE: Minimum valid clock requirement after MPSM entry. Present only in designs configured to support DDR4. Unit: Clocks. F - r configurations with MEMC_FREQ_RATIO=2, divide the value calculated using the above equation by 2, and round it up to next i - teger.*/ -#undef DDRC_DRAMTMG11_T_CKMPE_DEFVAL -#undef DDRC_DRAMTMG11_T_CKMPE_SHIFT -#undef DDRC_DRAMTMG11_T_CKMPE_MASK -#define DDRC_DRAMTMG11_T_CKMPE_DEFVAL 0x440C021C -#define DDRC_DRAMTMG11_T_CKMPE_SHIFT 0 -#define DDRC_DRAMTMG11_T_CKMPE_MASK 0x0000001FU - -/*tCMDCKE: Delay from valid command to CKE input LOW. Set this to the larger of tESCKE or tCMDCKE For configurations with MEMC_ - REQ_RATIO=2, program this to (max(tESCKE, tCMDCKE)/2) and round it up to next integer value.*/ -#undef DDRC_DRAMTMG12_T_CMDCKE_DEFVAL -#undef DDRC_DRAMTMG12_T_CMDCKE_SHIFT -#undef DDRC_DRAMTMG12_T_CMDCKE_MASK -#define DDRC_DRAMTMG12_T_CMDCKE_DEFVAL 0x00020610 -#define DDRC_DRAMTMG12_T_CMDCKE_SHIFT 16 -#define DDRC_DRAMTMG12_T_CMDCKE_MASK 0x00030000U - -/*tCKEHCMD: Valid command requirement after CKE input HIGH. For configurations with MEMC_FREQ_RATIO=2, program this to (tCKEHCM - /2) and round it up to next integer value.*/ -#undef DDRC_DRAMTMG12_T_CKEHCMD_DEFVAL -#undef DDRC_DRAMTMG12_T_CKEHCMD_SHIFT -#undef DDRC_DRAMTMG12_T_CKEHCMD_MASK -#define DDRC_DRAMTMG12_T_CKEHCMD_DEFVAL 0x00020610 -#define DDRC_DRAMTMG12_T_CKEHCMD_SHIFT 8 -#define DDRC_DRAMTMG12_T_CKEHCMD_MASK 0x00000F00U - -/*tMRD_PDA: This is the Mode Register Set command cycle time in PDA mode. For configurations with MEMC_FREQ_RATIO=2, program th - s to (tMRD_PDA/2) and round it up to next integer value.*/ -#undef DDRC_DRAMTMG12_T_MRD_PDA_DEFVAL -#undef DDRC_DRAMTMG12_T_MRD_PDA_SHIFT -#undef DDRC_DRAMTMG12_T_MRD_PDA_MASK -#define DDRC_DRAMTMG12_T_MRD_PDA_DEFVAL 0x00020610 -#define DDRC_DRAMTMG12_T_MRD_PDA_SHIFT 0 -#define DDRC_DRAMTMG12_T_MRD_PDA_MASK 0x0000001FU - -/*- 1 - Disable uMCTL2 generation of ZQCS/MPC(ZQ calibration) command. Register DBGCMD.zq_calib_short can be used instead to is - ue ZQ calibration request from APB module. - 0 - Internally generate ZQCS/MPC(ZQ calibration) commands based on ZQCTL1.t_zq_s - ort_interval_x1024. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.*/ -#undef DDRC_ZQCTL0_DIS_AUTO_ZQ_DEFVAL -#undef DDRC_ZQCTL0_DIS_AUTO_ZQ_SHIFT -#undef DDRC_ZQCTL0_DIS_AUTO_ZQ_MASK -#define DDRC_ZQCTL0_DIS_AUTO_ZQ_DEFVAL 0x02000040 -#define DDRC_ZQCTL0_DIS_AUTO_ZQ_SHIFT 31 -#define DDRC_ZQCTL0_DIS_AUTO_ZQ_MASK 0x80000000U - -/*- 1 - Disable issuing of ZQCL/MPC(ZQ calibration) command at Self-Refresh/SR-Powerdown exit. Only applicable when run in DDR3 - or DDR4 or LPDDR2 or LPDDR3 or LPDDR4 mode. - 0 - Enable issuing of ZQCL/MPC(ZQ calibration) command at Self-Refresh/SR-Power - own exit. Only applicable when run in DDR3 or DDR4 or LPDDR2 or LPDDR3 or LPDDR4 mode. This is only present for designs suppo - ting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.*/ -#undef DDRC_ZQCTL0_DIS_SRX_ZQCL_DEFVAL -#undef DDRC_ZQCTL0_DIS_SRX_ZQCL_SHIFT -#undef DDRC_ZQCTL0_DIS_SRX_ZQCL_MASK -#define DDRC_ZQCTL0_DIS_SRX_ZQCL_DEFVAL 0x02000040 -#define DDRC_ZQCTL0_DIS_SRX_ZQCL_SHIFT 30 -#define DDRC_ZQCTL0_DIS_SRX_ZQCL_MASK 0x40000000U - -/*- 1 - Denotes that ZQ resistor is shared between ranks. Means ZQinit/ZQCL/ZQCS/MPC(ZQ calibration) commands are sent to one r - nk at a time with tZQinit/tZQCL/tZQCS/tZQCAL/tZQLAT timing met between commands so that commands to different ranks do not ov - rlap. - 0 - ZQ resistor is not shared. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.*/ -#undef DDRC_ZQCTL0_ZQ_RESISTOR_SHARED_DEFVAL -#undef DDRC_ZQCTL0_ZQ_RESISTOR_SHARED_SHIFT -#undef DDRC_ZQCTL0_ZQ_RESISTOR_SHARED_MASK -#define DDRC_ZQCTL0_ZQ_RESISTOR_SHARED_DEFVAL 0x02000040 -#define DDRC_ZQCTL0_ZQ_RESISTOR_SHARED_SHIFT 29 -#define DDRC_ZQCTL0_ZQ_RESISTOR_SHARED_MASK 0x20000000U - -/*- 1 - Disable issuing of ZQCL command at Maximum Power Saving Mode exit. Only applicable when run in DDR4 mode. - 0 - Enable - ssuing of ZQCL command at Maximum Power Saving Mode exit. Only applicable when run in DDR4 mode. This is only present for des - gns supporting DDR4 devices.*/ -#undef DDRC_ZQCTL0_DIS_MPSMX_ZQCL_DEFVAL -#undef DDRC_ZQCTL0_DIS_MPSMX_ZQCL_SHIFT -#undef DDRC_ZQCTL0_DIS_MPSMX_ZQCL_MASK -#define DDRC_ZQCTL0_DIS_MPSMX_ZQCL_DEFVAL 0x02000040 -#define DDRC_ZQCTL0_DIS_MPSMX_ZQCL_SHIFT 28 -#define DDRC_ZQCTL0_DIS_MPSMX_ZQCL_MASK 0x10000000U - -/*tZQoper for DDR3/DDR4, tZQCL for LPDDR2/LPDDR3, tZQCAL for LPDDR4: Number of cycles of NOP required after a ZQCL (ZQ calibrat - on long)/MPC(ZQ Start) command is issued to SDRAM. For configurations with MEMC_FREQ_RATIO=2: DDR3/DDR4: program this to tZQo - er/2 and round it up to the next integer value. LPDDR2/LPDDR3: program this to tZQCL/2 and round it up to the next integer va - ue. LPDDR4: program this to tZQCAL/2 and round it up to the next integer value. Unit: Clock cycles. This is only present for - esigns supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.*/ -#undef DDRC_ZQCTL0_T_ZQ_LONG_NOP_DEFVAL -#undef DDRC_ZQCTL0_T_ZQ_LONG_NOP_SHIFT -#undef DDRC_ZQCTL0_T_ZQ_LONG_NOP_MASK -#define DDRC_ZQCTL0_T_ZQ_LONG_NOP_DEFVAL 0x02000040 -#define DDRC_ZQCTL0_T_ZQ_LONG_NOP_SHIFT 16 -#define DDRC_ZQCTL0_T_ZQ_LONG_NOP_MASK 0x07FF0000U - -/*tZQCS for DDR3/DD4/LPDDR2/LPDDR3, tZQLAT for LPDDR4: Number of cycles of NOP required after a ZQCS (ZQ calibration short)/MPC - ZQ Latch) command is issued to SDRAM. For configurations with MEMC_FREQ_RATIO=2, program this to tZQCS/2 and round it up to t - e next integer value. Unit: Clock cycles. This is only present for designs supporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devic - s.*/ -#undef DDRC_ZQCTL0_T_ZQ_SHORT_NOP_DEFVAL -#undef DDRC_ZQCTL0_T_ZQ_SHORT_NOP_SHIFT -#undef DDRC_ZQCTL0_T_ZQ_SHORT_NOP_MASK -#define DDRC_ZQCTL0_T_ZQ_SHORT_NOP_DEFVAL 0x02000040 -#define DDRC_ZQCTL0_T_ZQ_SHORT_NOP_SHIFT 0 -#define DDRC_ZQCTL0_T_ZQ_SHORT_NOP_MASK 0x000003FFU - -/*tZQReset: Number of cycles of NOP required after a ZQReset (ZQ calibration Reset) command is issued to SDRAM. For configurati - ns with MEMC_FREQ_RATIO=2, program this to tZQReset/2 and round it up to the next integer value. Unit: Clock cycles. This is - nly present for designs supporting LPDDR2/LPDDR3/LPDDR4 devices.*/ -#undef DDRC_ZQCTL1_T_ZQ_RESET_NOP_DEFVAL -#undef DDRC_ZQCTL1_T_ZQ_RESET_NOP_SHIFT -#undef DDRC_ZQCTL1_T_ZQ_RESET_NOP_MASK -#define DDRC_ZQCTL1_T_ZQ_RESET_NOP_DEFVAL 0x02000100 -#define DDRC_ZQCTL1_T_ZQ_RESET_NOP_SHIFT 20 -#define DDRC_ZQCTL1_T_ZQ_RESET_NOP_MASK 0x3FF00000U - -/*Average interval to wait between automatically issuing ZQCS (ZQ calibration short)/MPC(ZQ calibration) commands to DDR3/DDR4/ - PDDR2/LPDDR3/LPDDR4 devices. Meaningless, if ZQCTL0.dis_auto_zq=1. Unit: 1024 clock cycles. This is only present for designs - upporting DDR3/DDR4 or LPDDR2/LPDDR3/LPDDR4 devices.*/ -#undef DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024_DEFVAL -#undef DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024_SHIFT -#undef DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024_MASK -#define DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024_DEFVAL 0x02000100 -#define DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024_SHIFT 0 -#define DDRC_ZQCTL1_T_ZQ_SHORT_INTERVAL_X1024_MASK 0x000FFFFFU - -/*Specifies the number of DFI clock cycles after an assertion or de-assertion of the DFI control signals that the control signa - s at the PHY-DRAM interface reflect the assertion or de-assertion. If the DFI clock and the memory clock are not phase-aligne - , this timing parameter should be rounded up to the next integer value. Note that if using RDIMM, it is necessary to incremen - this parameter by RDIMM's extra cycle of latency in terms of DFI clock.*/ -#undef DDRC_DFITMG0_DFI_T_CTRL_DELAY_DEFVAL -#undef DDRC_DFITMG0_DFI_T_CTRL_DELAY_SHIFT -#undef DDRC_DFITMG0_DFI_T_CTRL_DELAY_MASK -#define DDRC_DFITMG0_DFI_T_CTRL_DELAY_DEFVAL 0x07020002 -#define DDRC_DFITMG0_DFI_T_CTRL_DELAY_SHIFT 24 -#define DDRC_DFITMG0_DFI_T_CTRL_DELAY_MASK 0x1F000000U - -/*Defines whether dfi_rddata_en/dfi_rddata/dfi_rddata_valid is generated using HDR or SDR values Selects whether value in DFITM - 0.dfi_t_rddata_en is in terms of SDR or HDR clock cycles: - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles R - fer to PHY specification for correct value.*/ -#undef DDRC_DFITMG0_DFI_RDDATA_USE_SDR_DEFVAL -#undef DDRC_DFITMG0_DFI_RDDATA_USE_SDR_SHIFT -#undef DDRC_DFITMG0_DFI_RDDATA_USE_SDR_MASK -#define DDRC_DFITMG0_DFI_RDDATA_USE_SDR_DEFVAL 0x07020002 -#define DDRC_DFITMG0_DFI_RDDATA_USE_SDR_SHIFT 23 -#define DDRC_DFITMG0_DFI_RDDATA_USE_SDR_MASK 0x00800000U - -/*Time from the assertion of a read command on the DFI interface to the assertion of the dfi_rddata_en signal. Refer to PHY spe - ification for correct value. This corresponds to the DFI parameter trddata_en. Note that, depending on the PHY, if using RDIM - , it may be necessary to use the value (CL + 1) in the calculation of trddata_en. This is to compensate for the extra cycle o - latency through the RDIMM. Unit: Clocks*/ -#undef DDRC_DFITMG0_DFI_T_RDDATA_EN_DEFVAL -#undef DDRC_DFITMG0_DFI_T_RDDATA_EN_SHIFT -#undef DDRC_DFITMG0_DFI_T_RDDATA_EN_MASK -#define DDRC_DFITMG0_DFI_T_RDDATA_EN_DEFVAL 0x07020002 -#define DDRC_DFITMG0_DFI_T_RDDATA_EN_SHIFT 16 -#define DDRC_DFITMG0_DFI_T_RDDATA_EN_MASK 0x003F0000U - -/*Defines whether dfi_wrdata_en/dfi_wrdata/dfi_wrdata_mask is generated using HDR or SDR values Selects whether value in DFITMG - .dfi_tphy_wrlat is in terms of SDR or HDR clock cycles Selects whether value in DFITMG0.dfi_tphy_wrdata is in terms of SDR or - HDR clock cycles - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles Refer to PHY specification for correct val - e.*/ -#undef DDRC_DFITMG0_DFI_WRDATA_USE_SDR_DEFVAL -#undef DDRC_DFITMG0_DFI_WRDATA_USE_SDR_SHIFT -#undef DDRC_DFITMG0_DFI_WRDATA_USE_SDR_MASK -#define DDRC_DFITMG0_DFI_WRDATA_USE_SDR_DEFVAL 0x07020002 -#define DDRC_DFITMG0_DFI_WRDATA_USE_SDR_SHIFT 15 -#define DDRC_DFITMG0_DFI_WRDATA_USE_SDR_MASK 0x00008000U - -/*Specifies the number of clock cycles between when dfi_wrdata_en is asserted to when the associated write data is driven on th - dfi_wrdata signal. This corresponds to the DFI timing parameter tphy_wrdata. Refer to PHY specification for correct value. N - te, max supported value is 8. Unit: Clocks*/ -#undef DDRC_DFITMG0_DFI_TPHY_WRDATA_DEFVAL -#undef DDRC_DFITMG0_DFI_TPHY_WRDATA_SHIFT -#undef DDRC_DFITMG0_DFI_TPHY_WRDATA_MASK -#define DDRC_DFITMG0_DFI_TPHY_WRDATA_DEFVAL 0x07020002 -#define DDRC_DFITMG0_DFI_TPHY_WRDATA_SHIFT 8 -#define DDRC_DFITMG0_DFI_TPHY_WRDATA_MASK 0x00003F00U - -/*Write latency Number of clocks from the write command to write data enable (dfi_wrdata_en). This corresponds to the DFI timin - parameter tphy_wrlat. Refer to PHY specification for correct value.Note that, depending on the PHY, if using RDIMM, it may b - necessary to use the value (CL + 1) in the calculation of tphy_wrlat. This is to compensate for the extra cycle of latency t - rough the RDIMM.*/ -#undef DDRC_DFITMG0_DFI_TPHY_WRLAT_DEFVAL -#undef DDRC_DFITMG0_DFI_TPHY_WRLAT_SHIFT -#undef DDRC_DFITMG0_DFI_TPHY_WRLAT_MASK -#define DDRC_DFITMG0_DFI_TPHY_WRLAT_DEFVAL 0x07020002 -#define DDRC_DFITMG0_DFI_TPHY_WRLAT_SHIFT 0 -#define DDRC_DFITMG0_DFI_TPHY_WRLAT_MASK 0x0000003FU - -/*Specifies the number of DFI PHY clocks between when the dfi_cs signal is asserted and when the associated command is driven. - his field is used for CAL mode, should be set to '0' or the value which matches the CAL mode register setting in the DRAM. If - the PHY can add the latency for CAL mode, this should be set to '0'. Valid Range: 0, 3, 4, 5, 6, and 8*/ -#undef DDRC_DFITMG1_DFI_T_CMD_LAT_DEFVAL -#undef DDRC_DFITMG1_DFI_T_CMD_LAT_SHIFT -#undef DDRC_DFITMG1_DFI_T_CMD_LAT_MASK -#define DDRC_DFITMG1_DFI_T_CMD_LAT_DEFVAL 0x00000404 -#define DDRC_DFITMG1_DFI_T_CMD_LAT_SHIFT 28 -#define DDRC_DFITMG1_DFI_T_CMD_LAT_MASK 0xF0000000U - -/*Specifies the number of DFI PHY clocks between when the dfi_cs signal is asserted and when the associated dfi_parity_in signa - is driven.*/ -#undef DDRC_DFITMG1_DFI_T_PARIN_LAT_DEFVAL -#undef DDRC_DFITMG1_DFI_T_PARIN_LAT_SHIFT -#undef DDRC_DFITMG1_DFI_T_PARIN_LAT_MASK -#define DDRC_DFITMG1_DFI_T_PARIN_LAT_DEFVAL 0x00000404 -#define DDRC_DFITMG1_DFI_T_PARIN_LAT_SHIFT 24 -#define DDRC_DFITMG1_DFI_T_PARIN_LAT_MASK 0x03000000U - -/*Specifies the number of DFI clocks between when the dfi_wrdata_en signal is asserted and when the corresponding write data tr - nsfer is completed on the DRAM bus. This corresponds to the DFI timing parameter twrdata_delay. Refer to PHY specification fo - correct value. For DFI 3.0 PHY, set to twrdata_delay, a new timing parameter introduced in DFI 3.0. For DFI 2.1 PHY, set to - phy_wrdata + (delay of DFI write data to the DRAM). Value to be programmed is in terms of DFI clocks, not PHY clocks. In FREQ - RATIO=2, divide PHY's value by 2 and round up to next integer. If using DFITMG0.dfi_wrdata_use_sdr=1, add 1 to the value. Uni - : Clocks*/ -#undef DDRC_DFITMG1_DFI_T_WRDATA_DELAY_DEFVAL -#undef DDRC_DFITMG1_DFI_T_WRDATA_DELAY_SHIFT -#undef DDRC_DFITMG1_DFI_T_WRDATA_DELAY_MASK -#define DDRC_DFITMG1_DFI_T_WRDATA_DELAY_DEFVAL 0x00000404 -#define DDRC_DFITMG1_DFI_T_WRDATA_DELAY_SHIFT 16 -#define DDRC_DFITMG1_DFI_T_WRDATA_DELAY_MASK 0x001F0000U - -/*Specifies the number of DFI clock cycles from the assertion of the dfi_dram_clk_disable signal on the DFI until the clock to - he DRAM memory devices, at the PHY-DRAM boundary, maintains a low value. If the DFI clock and the memory clock are not phase - ligned, this timing parameter should be rounded up to the next integer value.*/ -#undef DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE_DEFVAL -#undef DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE_SHIFT -#undef DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE_MASK -#define DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE_DEFVAL 0x00000404 -#define DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE_SHIFT 8 -#define DDRC_DFITMG1_DFI_T_DRAM_CLK_DISABLE_MASK 0x00000F00U - -/*Specifies the number of DFI clock cycles from the de-assertion of the dfi_dram_clk_disable signal on the DFI until the first - alid rising edge of the clock to the DRAM memory devices, at the PHY-DRAM boundary. If the DFI clock and the memory clock are - not phase aligned, this timing parameter should be rounded up to the next integer value.*/ -#undef DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE_DEFVAL -#undef DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE_SHIFT -#undef DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE_MASK -#define DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE_DEFVAL 0x00000404 -#define DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE_SHIFT 0 -#define DDRC_DFITMG1_DFI_T_DRAM_CLK_ENABLE_MASK 0x0000000FU - -/*Setting for DFI's tlp_resp time. Same value is used for both Power Down, Self Refresh, Deep Power Down and Maximum Power Savi - g modes. DFI 2.1 specification onwards, recommends using a fixed value of 7 always.*/ -#undef DDRC_DFILPCFG0_DFI_TLP_RESP_DEFVAL -#undef DDRC_DFILPCFG0_DFI_TLP_RESP_SHIFT -#undef DDRC_DFILPCFG0_DFI_TLP_RESP_MASK -#define DDRC_DFILPCFG0_DFI_TLP_RESP_DEFVAL 0x07000000 -#define DDRC_DFILPCFG0_DFI_TLP_RESP_SHIFT 24 -#define DDRC_DFILPCFG0_DFI_TLP_RESP_MASK 0x0F000000U - -/*Value to drive on dfi_lp_wakeup signal when Deep Power Down mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - 16 - cycles - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - - 2048 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0xD - - 31072 cycles - 0xE - 262144 cycles - 0xF - Unlimited This is only present for designs supporting mDDR or LPDDR2/LPDDR3 device - .*/ -#undef DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD_DEFVAL -#undef DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD_SHIFT -#undef DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD_MASK -#define DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD_DEFVAL 0x07000000 -#define DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD_SHIFT 20 -#define DDRC_DFILPCFG0_DFI_LP_WAKEUP_DPD_MASK 0x00F00000U - -/*Enables DFI Low Power interface handshaking during Deep Power Down Entry/Exit. - 0 - Disabled - 1 - Enabled This is only pres - nt for designs supporting mDDR or LPDDR2/LPDDR3 devices.*/ -#undef DDRC_DFILPCFG0_DFI_LP_EN_DPD_DEFVAL -#undef DDRC_DFILPCFG0_DFI_LP_EN_DPD_SHIFT -#undef DDRC_DFILPCFG0_DFI_LP_EN_DPD_MASK -#define DDRC_DFILPCFG0_DFI_LP_EN_DPD_DEFVAL 0x07000000 -#define DDRC_DFILPCFG0_DFI_LP_EN_DPD_SHIFT 16 -#define DDRC_DFILPCFG0_DFI_LP_EN_DPD_MASK 0x00010000U - -/*Value to drive on dfi_lp_wakeup signal when Self Refresh mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - 16 cy - les - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - - 048 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0xD - 131 - 72 cycles - 0xE - 262144 cycles - 0xF - Unlimited*/ -#undef DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR_DEFVAL -#undef DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR_SHIFT -#undef DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR_MASK -#define DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR_DEFVAL 0x07000000 -#define DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR_SHIFT 12 -#define DDRC_DFILPCFG0_DFI_LP_WAKEUP_SR_MASK 0x0000F000U - -/*Enables DFI Low Power interface handshaking during Self Refresh Entry/Exit. - 0 - Disabled - 1 - Enabled*/ -#undef DDRC_DFILPCFG0_DFI_LP_EN_SR_DEFVAL -#undef DDRC_DFILPCFG0_DFI_LP_EN_SR_SHIFT -#undef DDRC_DFILPCFG0_DFI_LP_EN_SR_MASK -#define DDRC_DFILPCFG0_DFI_LP_EN_SR_DEFVAL 0x07000000 -#define DDRC_DFILPCFG0_DFI_LP_EN_SR_SHIFT 8 -#define DDRC_DFILPCFG0_DFI_LP_EN_SR_MASK 0x00000100U - -/*Value to drive on dfi_lp_wakeup signal when Power Down mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - 16 cycl - s - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - 20 - 8 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0xD - 13107 - cycles - 0xE - 262144 cycles - 0xF - Unlimited*/ -#undef DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD_DEFVAL -#undef DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD_SHIFT -#undef DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD_MASK -#define DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD_DEFVAL 0x07000000 -#define DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD_SHIFT 4 -#define DDRC_DFILPCFG0_DFI_LP_WAKEUP_PD_MASK 0x000000F0U - -/*Enables DFI Low Power interface handshaking during Power Down Entry/Exit. - 0 - Disabled - 1 - Enabled*/ -#undef DDRC_DFILPCFG0_DFI_LP_EN_PD_DEFVAL -#undef DDRC_DFILPCFG0_DFI_LP_EN_PD_SHIFT -#undef DDRC_DFILPCFG0_DFI_LP_EN_PD_MASK -#define DDRC_DFILPCFG0_DFI_LP_EN_PD_DEFVAL 0x07000000 -#define DDRC_DFILPCFG0_DFI_LP_EN_PD_SHIFT 0 -#define DDRC_DFILPCFG0_DFI_LP_EN_PD_MASK 0x00000001U - -/*Value to drive on dfi_lp_wakeup signal when Maximum Power Saving Mode is entered. Determines the DFI's tlp_wakeup time: - 0x0 - - 16 cycles - 0x1 - 32 cycles - 0x2 - 64 cycles - 0x3 - 128 cycles - 0x4 - 256 cycles - 0x5 - 512 cycles - 0x6 - 1024 cycles - 0x7 - 2048 cycles - 0x8 - 4096 cycles - 0x9 - 8192 cycles - 0xA - 16384 cycles - 0xB - 32768 cycles - 0xC - 65536 cycles - 0 - D - 131072 cycles - 0xE - 262144 cycles - 0xF - Unlimited This is only present for designs supporting DDR4 devices.*/ -#undef DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM_DEFVAL -#undef DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM_SHIFT -#undef DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM_MASK -#define DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM_DEFVAL 0x00000000 -#define DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM_SHIFT 4 -#define DDRC_DFILPCFG1_DFI_LP_WAKEUP_MPSM_MASK 0x000000F0U - -/*Enables DFI Low Power interface handshaking during Maximum Power Saving Mode Entry/Exit. - 0 - Disabled - 1 - Enabled This is - only present for designs supporting DDR4 devices.*/ -#undef DDRC_DFILPCFG1_DFI_LP_EN_MPSM_DEFVAL -#undef DDRC_DFILPCFG1_DFI_LP_EN_MPSM_SHIFT -#undef DDRC_DFILPCFG1_DFI_LP_EN_MPSM_MASK -#define DDRC_DFILPCFG1_DFI_LP_EN_MPSM_DEFVAL 0x00000000 -#define DDRC_DFILPCFG1_DFI_LP_EN_MPSM_SHIFT 0 -#define DDRC_DFILPCFG1_DFI_LP_EN_MPSM_MASK 0x00000001U - -/*This is the minimum amount of time between uMCTL2 initiated DFI update requests (which is executed whenever the uMCTL2 is idl - ). Set this number higher to reduce the frequency of update requests, which can have a small impact on the latency of the fir - t read request when the uMCTL2 is idle. Unit: 1024 clocks*/ -#undef DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024_DEFVAL -#undef DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024_SHIFT -#undef DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024_MASK -#define DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024_DEFVAL 0x00000000 -#define DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024_SHIFT 16 -#define DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MIN_X1024_MASK 0x00FF0000U - -/*This is the maximum amount of time between uMCTL2 initiated DFI update requests. This timer resets with each update request; - hen the timer expires dfi_ctrlupd_req is sent and traffic is blocked until the dfi_ctrlupd_ackx is received. PHY can use this - idle time to recalibrate the delay lines to the DLLs. The DFI controller update is also used to reset PHY FIFO pointers in ca - e of data capture errors. Updates are required to maintain calibration over PVT, but frequent updates may impact performance. - Note: Value programmed for DFIUPD1.dfi_t_ctrlupd_interval_max_x1024 must be greater than DFIUPD1.dfi_t_ctrlupd_interval_min_x - 024. Unit: 1024 clocks*/ -#undef DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024_DEFVAL -#undef DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024_SHIFT -#undef DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024_MASK -#define DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024_DEFVAL 0x00000000 -#define DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024_SHIFT 0 -#define DDRC_DFIUPD1_DFI_T_CTRLUPD_INTERVAL_MAX_X1024_MASK 0x000000FFU - -/*Defines polarity of dfi_wrdata_cs and dfi_rddata_cs signals. - 0: Signals are active low - 1: Signals are active high*/ -#undef DDRC_DFIMISC_DFI_DATA_CS_POLARITY_DEFVAL -#undef DDRC_DFIMISC_DFI_DATA_CS_POLARITY_SHIFT -#undef DDRC_DFIMISC_DFI_DATA_CS_POLARITY_MASK -#define DDRC_DFIMISC_DFI_DATA_CS_POLARITY_DEFVAL 0x00000001 -#define DDRC_DFIMISC_DFI_DATA_CS_POLARITY_SHIFT 2 -#define DDRC_DFIMISC_DFI_DATA_CS_POLARITY_MASK 0x00000004U - -/*DBI implemented in DDRC or PHY. - 0 - DDRC implements DBI functionality. - 1 - PHY implements DBI functionality. Present only - in designs configured to support DDR4 and LPDDR4.*/ -#undef DDRC_DFIMISC_PHY_DBI_MODE_DEFVAL -#undef DDRC_DFIMISC_PHY_DBI_MODE_SHIFT -#undef DDRC_DFIMISC_PHY_DBI_MODE_MASK -#define DDRC_DFIMISC_PHY_DBI_MODE_DEFVAL 0x00000001 -#define DDRC_DFIMISC_PHY_DBI_MODE_SHIFT 1 -#define DDRC_DFIMISC_PHY_DBI_MODE_MASK 0x00000002U - -/*PHY initialization complete enable signal. When asserted the dfi_init_complete signal can be used to trigger SDRAM initialisa - ion*/ -#undef DDRC_DFIMISC_DFI_INIT_COMPLETE_EN_DEFVAL -#undef DDRC_DFIMISC_DFI_INIT_COMPLETE_EN_SHIFT -#undef DDRC_DFIMISC_DFI_INIT_COMPLETE_EN_MASK -#define DDRC_DFIMISC_DFI_INIT_COMPLETE_EN_DEFVAL 0x00000001 -#define DDRC_DFIMISC_DFI_INIT_COMPLETE_EN_SHIFT 0 -#define DDRC_DFIMISC_DFI_INIT_COMPLETE_EN_MASK 0x00000001U - -/*>Number of clocks between when a read command is sent on the DFI control interface and when the associated dfi_rddata_cs sign - l is asserted. This corresponds to the DFI timing parameter tphy_rdcslat. Refer to PHY specification for correct value.*/ -#undef DDRC_DFITMG2_DFI_TPHY_RDCSLAT_DEFVAL -#undef DDRC_DFITMG2_DFI_TPHY_RDCSLAT_SHIFT -#undef DDRC_DFITMG2_DFI_TPHY_RDCSLAT_MASK -#define DDRC_DFITMG2_DFI_TPHY_RDCSLAT_DEFVAL 0x00000202 -#define DDRC_DFITMG2_DFI_TPHY_RDCSLAT_SHIFT 8 -#define DDRC_DFITMG2_DFI_TPHY_RDCSLAT_MASK 0x00003F00U - -/*Number of clocks between when a write command is sent on the DFI control interface and when the associated dfi_wrdata_cs sign - l is asserted. This corresponds to the DFI timing parameter tphy_wrcslat. Refer to PHY specification for correct value.*/ -#undef DDRC_DFITMG2_DFI_TPHY_WRCSLAT_DEFVAL -#undef DDRC_DFITMG2_DFI_TPHY_WRCSLAT_SHIFT -#undef DDRC_DFITMG2_DFI_TPHY_WRCSLAT_MASK -#define DDRC_DFITMG2_DFI_TPHY_WRCSLAT_DEFVAL 0x00000202 -#define DDRC_DFITMG2_DFI_TPHY_WRCSLAT_SHIFT 0 -#define DDRC_DFITMG2_DFI_TPHY_WRCSLAT_MASK 0x0000003FU - -/*Read DBI enable signal in DDRC. - 0 - Read DBI is disabled. - 1 - Read DBI is enabled. This signal must be set the same value - as DRAM's mode register. - DDR4: MR5 bit A12. When x4 devices are used, this signal must be set to 0. - LPDDR4: MR3[6]*/ -#undef DDRC_DBICTL_RD_DBI_EN_DEFVAL -#undef DDRC_DBICTL_RD_DBI_EN_SHIFT -#undef DDRC_DBICTL_RD_DBI_EN_MASK -#define DDRC_DBICTL_RD_DBI_EN_DEFVAL 0x00000001 -#define DDRC_DBICTL_RD_DBI_EN_SHIFT 2 -#define DDRC_DBICTL_RD_DBI_EN_MASK 0x00000004U - -/*Write DBI enable signal in DDRC. - 0 - Write DBI is disabled. - 1 - Write DBI is enabled. This signal must be set the same va - ue as DRAM's mode register. - DDR4: MR5 bit A11. When x4 devices are used, this signal must be set to 0. - LPDDR4: MR3[7]*/ -#undef DDRC_DBICTL_WR_DBI_EN_DEFVAL -#undef DDRC_DBICTL_WR_DBI_EN_SHIFT -#undef DDRC_DBICTL_WR_DBI_EN_MASK -#define DDRC_DBICTL_WR_DBI_EN_DEFVAL 0x00000001 -#define DDRC_DBICTL_WR_DBI_EN_SHIFT 1 -#define DDRC_DBICTL_WR_DBI_EN_MASK 0x00000002U - -/*DM enable signal in DDRC. - 0 - DM is disabled. - 1 - DM is enabled. This signal must be set the same logical value as DRAM's - mode register. - DDR4: Set this to same value as MR5 bit A10. When x4 devices are used, this signal must be set to 0. - LPDDR - : Set this to inverted value of MR13[5] which is opposite polarity from this signal*/ -#undef DDRC_DBICTL_DM_EN_DEFVAL -#undef DDRC_DBICTL_DM_EN_SHIFT -#undef DDRC_DBICTL_DM_EN_MASK -#define DDRC_DBICTL_DM_EN_DEFVAL 0x00000001 -#define DDRC_DBICTL_DM_EN_SHIFT 0 -#define DDRC_DBICTL_DM_EN_MASK 0x00000001U - -/*Selects the HIF address bit used as rank address bit 0. Valid Range: 0 to 27, and 31 Internal Base: 6 The selected HIF addres - bit is determined by adding the internal base to the value of this field. If set to 31, rank address bit 0 is set to 0.*/ -#undef DDRC_ADDRMAP0_ADDRMAP_CS_BIT0_DEFVAL -#undef DDRC_ADDRMAP0_ADDRMAP_CS_BIT0_SHIFT -#undef DDRC_ADDRMAP0_ADDRMAP_CS_BIT0_MASK -#define DDRC_ADDRMAP0_ADDRMAP_CS_BIT0_DEFVAL -#define DDRC_ADDRMAP0_ADDRMAP_CS_BIT0_SHIFT 0 -#define DDRC_ADDRMAP0_ADDRMAP_CS_BIT0_MASK 0x0000001FU - -/*Selects the HIF address bit used as bank address bit 2. Valid Range: 0 to 29 and 31 Internal Base: 4 The selected HIF address - bit is determined by adding the internal base to the value of this field. If set to 31, bank address bit 2 is set to 0.*/ -#undef DDRC_ADDRMAP1_ADDRMAP_BANK_B2_DEFVAL -#undef DDRC_ADDRMAP1_ADDRMAP_BANK_B2_SHIFT -#undef DDRC_ADDRMAP1_ADDRMAP_BANK_B2_MASK -#define DDRC_ADDRMAP1_ADDRMAP_BANK_B2_DEFVAL 0x00000000 -#define DDRC_ADDRMAP1_ADDRMAP_BANK_B2_SHIFT 16 -#define DDRC_ADDRMAP1_ADDRMAP_BANK_B2_MASK 0x001F0000U - -/*Selects the HIF address bits used as bank address bit 1. Valid Range: 0 to 30 Internal Base: 3 The selected HIF address bit f - r each of the bank address bits is determined by adding the internal base to the value of this field.*/ -#undef DDRC_ADDRMAP1_ADDRMAP_BANK_B1_DEFVAL -#undef DDRC_ADDRMAP1_ADDRMAP_BANK_B1_SHIFT -#undef DDRC_ADDRMAP1_ADDRMAP_BANK_B1_MASK -#define DDRC_ADDRMAP1_ADDRMAP_BANK_B1_DEFVAL 0x00000000 -#define DDRC_ADDRMAP1_ADDRMAP_BANK_B1_SHIFT 8 -#define DDRC_ADDRMAP1_ADDRMAP_BANK_B1_MASK 0x00001F00U - -/*Selects the HIF address bits used as bank address bit 0. Valid Range: 0 to 30 Internal Base: 2 The selected HIF address bit f - r each of the bank address bits is determined by adding the internal base to the value of this field.*/ -#undef DDRC_ADDRMAP1_ADDRMAP_BANK_B0_DEFVAL -#undef DDRC_ADDRMAP1_ADDRMAP_BANK_B0_SHIFT -#undef DDRC_ADDRMAP1_ADDRMAP_BANK_B0_MASK -#define DDRC_ADDRMAP1_ADDRMAP_BANK_B0_DEFVAL 0x00000000 -#define DDRC_ADDRMAP1_ADDRMAP_BANK_B0_SHIFT 0 -#define DDRC_ADDRMAP1_ADDRMAP_BANK_B0_MASK 0x0000001FU - -/*- Full bus width mode: Selects the HIF address bit used as column address bit 5. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 6. - Quarter bus width mode: Selects the HIF address bit used as column address bit 7 . Vali - Range: 0 to 7, and 15 Internal Base: 5 The selected HIF address bit is determined by adding the internal base to the value o - this field. If set to 15, this column address bit is set to 0.*/ -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B5_DEFVAL -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B5_SHIFT -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B5_MASK -#define DDRC_ADDRMAP2_ADDRMAP_COL_B5_DEFVAL 0x00000000 -#define DDRC_ADDRMAP2_ADDRMAP_COL_B5_SHIFT 24 -#define DDRC_ADDRMAP2_ADDRMAP_COL_B5_MASK 0x0F000000U - -/*- Full bus width mode: Selects the HIF address bit used as column address bit 4. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 5. - Quarter bus width mode: Selects the HIF address bit used as column address bit 6. Valid - Range: 0 to 7, and 15 Internal Base: 4 The selected HIF address bit is determined by adding the internal base to the value of - this field. If set to 15, this column address bit is set to 0.*/ -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B4_DEFVAL -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B4_SHIFT -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B4_MASK -#define DDRC_ADDRMAP2_ADDRMAP_COL_B4_DEFVAL 0x00000000 -#define DDRC_ADDRMAP2_ADDRMAP_COL_B4_SHIFT 16 -#define DDRC_ADDRMAP2_ADDRMAP_COL_B4_MASK 0x000F0000U - -/*- Full bus width mode: Selects the HIF address bit used as column address bit 3. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 4. - Quarter bus width mode: Selects the HIF address bit used as column address bit 5. Valid - Range: 0 to 7 Internal Base: 3 The selected HIF address bit is determined by adding the internal base to the value of this fi - ld. Note, if UMCTL2_INCL_ARB=1 and MEMC_BURST_LENGTH=16, it is required to program this to 0, hence register does not exist i - this case.*/ -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B3_DEFVAL -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B3_SHIFT -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B3_MASK -#define DDRC_ADDRMAP2_ADDRMAP_COL_B3_DEFVAL 0x00000000 -#define DDRC_ADDRMAP2_ADDRMAP_COL_B3_SHIFT 8 -#define DDRC_ADDRMAP2_ADDRMAP_COL_B3_MASK 0x00000F00U - -/*- Full bus width mode: Selects the HIF address bit used as column address bit 2. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 3. - Quarter bus width mode: Selects the HIF address bit used as column address bit 4. Valid - Range: 0 to 7 Internal Base: 2 The selected HIF address bit is determined by adding the internal base to the value of this fi - ld. Note, if UMCTL2_INCL_ARB=1 and MEMC_BURST_LENGTH=8 or 16, it is required to program this to 0.*/ -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B2_DEFVAL -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B2_SHIFT -#undef DDRC_ADDRMAP2_ADDRMAP_COL_B2_MASK -#define DDRC_ADDRMAP2_ADDRMAP_COL_B2_DEFVAL 0x00000000 -#define DDRC_ADDRMAP2_ADDRMAP_COL_B2_SHIFT 0 -#define DDRC_ADDRMAP2_ADDRMAP_COL_B2_MASK 0x0000000FU - -/*- Full bus width mode: Selects the HIF address bit used as column address bit 9. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 11 (10 in LPDDR2/LPDDR3 mode). - Quarter bus width mode: Selects the HIF address bit used as - column address bit 13 (11 in LPDDR2/LPDDR3 mode). Valid Range: 0 to 7, and 15 Internal Base: 9 The selected HIF address bit i - determined by adding the internal base to the value of this field. If set to 15, this column address bit is set to 0. Note: - er JEDEC DDR2/3/mDDR specification, column address bit 10 is reserved for indicating auto-precharge, and hence no source addr - ss bit can be mapped to column address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus an - hence column bit 10 is used.*/ -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B9_DEFVAL -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B9_SHIFT -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B9_MASK -#define DDRC_ADDRMAP3_ADDRMAP_COL_B9_DEFVAL 0x00000000 -#define DDRC_ADDRMAP3_ADDRMAP_COL_B9_SHIFT 24 -#define DDRC_ADDRMAP3_ADDRMAP_COL_B9_MASK 0x0F000000U - -/*- Full bus width mode: Selects the HIF address bit used as column address bit 8. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 9. - Quarter bus width mode: Selects the HIF address bit used as column address bit 11 (10 i - LPDDR2/LPDDR3 mode). Valid Range: 0 to 7, and 15 Internal Base: 8 The selected HIF address bit is determined by adding the i - ternal base to the value of this field. If set to 15, this column address bit is set to 0. Note: Per JEDEC DDR2/3/mDDR specif - cation, column address bit 10 is reserved for indicating auto-precharge, and hence no source address bit can be mapped to col - mn address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus and hence column bit 10 is use - .*/ -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B8_DEFVAL -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B8_SHIFT -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B8_MASK -#define DDRC_ADDRMAP3_ADDRMAP_COL_B8_DEFVAL 0x00000000 -#define DDRC_ADDRMAP3_ADDRMAP_COL_B8_SHIFT 16 -#define DDRC_ADDRMAP3_ADDRMAP_COL_B8_MASK 0x000F0000U - -/*- Full bus width mode: Selects the HIF address bit used as column address bit 7. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 8. - Quarter bus width mode: Selects the HIF address bit used as column address bit 9. Valid - Range: 0 to 7, and 15 Internal Base: 7 The selected HIF address bit is determined by adding the internal base to the value of - this field. If set to 15, this column address bit is set to 0.*/ -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B7_DEFVAL -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B7_SHIFT -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B7_MASK -#define DDRC_ADDRMAP3_ADDRMAP_COL_B7_DEFVAL 0x00000000 -#define DDRC_ADDRMAP3_ADDRMAP_COL_B7_SHIFT 8 -#define DDRC_ADDRMAP3_ADDRMAP_COL_B7_MASK 0x00000F00U - -/*- Full bus width mode: Selects the HIF address bit used as column address bit 6. - Half bus width mode: Selects the HIF addre - s bit used as column address bit 7. - Quarter bus width mode: Selects the HIF address bit used as column address bit 8. Valid - Range: 0 to 7, and 15 Internal Base: 6 The selected HIF address bit is determined by adding the internal base to the value of - this field. If set to 15, this column address bit is set to 0.*/ -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B6_DEFVAL -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B6_SHIFT -#undef DDRC_ADDRMAP3_ADDRMAP_COL_B6_MASK -#define DDRC_ADDRMAP3_ADDRMAP_COL_B6_DEFVAL 0x00000000 -#define DDRC_ADDRMAP3_ADDRMAP_COL_B6_SHIFT 0 -#define DDRC_ADDRMAP3_ADDRMAP_COL_B6_MASK 0x0000000FU - -/*- Full bus width mode: Selects the HIF address bit used as column address bit 13 (11 in LPDDR2/LPDDR3 mode). - Half bus width - mode: Unused. To make it unused, this should be tied to 4'hF. - Quarter bus width mode: Unused. To make it unused, this must - e tied to 4'hF. Valid Range: 0 to 7, and 15 Internal Base: 11 The selected HIF address bit is determined by adding the intern - l base to the value of this field. If set to 15, this column address bit is set to 0. Note: Per JEDEC DDR2/3/mDDR specificati - n, column address bit 10 is reserved for indicating auto-precharge, and hence no source address bit can be mapped to column a - dress bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus and hence column bit 10 is used.*/ -#undef DDRC_ADDRMAP4_ADDRMAP_COL_B11_DEFVAL -#undef DDRC_ADDRMAP4_ADDRMAP_COL_B11_SHIFT -#undef DDRC_ADDRMAP4_ADDRMAP_COL_B11_MASK -#define DDRC_ADDRMAP4_ADDRMAP_COL_B11_DEFVAL 0x00000000 -#define DDRC_ADDRMAP4_ADDRMAP_COL_B11_SHIFT 8 -#define DDRC_ADDRMAP4_ADDRMAP_COL_B11_MASK 0x00000F00U - -/*- Full bus width mode: Selects the HIF address bit used as column address bit 11 (10 in LPDDR2/LPDDR3 mode). - Half bus width - mode: Selects the HIF address bit used as column address bit 13 (11 in LPDDR2/LPDDR3 mode). - Quarter bus width mode: UNUSED. - To make it unused, this must be tied to 4'hF. Valid Range: 0 to 7, and 15 Internal Base: 10 The selected HIF address bit is d - termined by adding the internal base to the value of this field. If set to 15, this column address bit is set to 0. Note: Per - JEDEC DDR2/3/mDDR specification, column address bit 10 is reserved for indicating auto-precharge, and hence no source address - bit can be mapped to column address bit 10. In LPDDR2/LPDDR3, there is a dedicated bit for auto-precharge in the CA bus and h - nce column bit 10 is used.*/ -#undef DDRC_ADDRMAP4_ADDRMAP_COL_B10_DEFVAL -#undef DDRC_ADDRMAP4_ADDRMAP_COL_B10_SHIFT -#undef DDRC_ADDRMAP4_ADDRMAP_COL_B10_MASK -#define DDRC_ADDRMAP4_ADDRMAP_COL_B10_DEFVAL 0x00000000 -#define DDRC_ADDRMAP4_ADDRMAP_COL_B10_SHIFT 0 -#define DDRC_ADDRMAP4_ADDRMAP_COL_B10_MASK 0x0000000FU - -/*Selects the HIF address bit used as row address bit 11. Valid Range: 0 to 11, and 15 Internal Base: 17 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 11 is set to 0.*/ -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B11_DEFVAL -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B11_SHIFT -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B11_MASK -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B11_DEFVAL 0x00000000 -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B11_SHIFT 24 -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B11_MASK 0x0F000000U - -/*Selects the HIF address bits used as row address bits 2 to 10. Valid Range: 0 to 11, and 15 Internal Base: 8 (for row address - bit 2), 9 (for row address bit 3), 10 (for row address bit 4) etc increasing to 16 (for row address bit 10) The selected HIF - ddress bit for each of the row address bits is determined by adding the internal base to the value of this field. When value - 5 is used the values of row address bits 2 to 10 are defined by registers ADDRMAP9, ADDRMAP10, ADDRMAP11.*/ -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10_DEFVAL -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10_SHIFT -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10_MASK -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10_DEFVAL 0x00000000 -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10_SHIFT 16 -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B2_10_MASK 0x000F0000U - -/*Selects the HIF address bits used as row address bit 1. Valid Range: 0 to 11 Internal Base: 7 The selected HIF address bit fo - each of the row address bits is determined by adding the internal base to the value of this field.*/ -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B1_DEFVAL -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B1_SHIFT -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B1_MASK -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B1_DEFVAL 0x00000000 -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B1_SHIFT 8 -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B1_MASK 0x00000F00U - -/*Selects the HIF address bits used as row address bit 0. Valid Range: 0 to 11 Internal Base: 6 The selected HIF address bit fo - each of the row address bits is determined by adding the internal base to the value of this field.*/ -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B0_DEFVAL -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B0_SHIFT -#undef DDRC_ADDRMAP5_ADDRMAP_ROW_B0_MASK -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B0_DEFVAL 0x00000000 -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B0_SHIFT 0 -#define DDRC_ADDRMAP5_ADDRMAP_ROW_B0_MASK 0x0000000FU - -/*Set this to 1 if there is an LPDDR3 SDRAM 6Gb or 12Gb device in use. - 1 - LPDDR3 SDRAM 6Gb/12Gb device in use. Every address - having row[14:13]==2'b11 is considered as invalid - 0 - non-LPDDR3 6Gb/12Gb device in use. All addresses are valid Present on - y in designs configured to support LPDDR3.*/ -#undef DDRC_ADDRMAP6_LPDDR3_6GB_12GB_DEFVAL -#undef DDRC_ADDRMAP6_LPDDR3_6GB_12GB_SHIFT -#undef DDRC_ADDRMAP6_LPDDR3_6GB_12GB_MASK -#define DDRC_ADDRMAP6_LPDDR3_6GB_12GB_DEFVAL 0x00000000 -#define DDRC_ADDRMAP6_LPDDR3_6GB_12GB_SHIFT 31 -#define DDRC_ADDRMAP6_LPDDR3_6GB_12GB_MASK 0x80000000U - -/*Selects the HIF address bit used as row address bit 15. Valid Range: 0 to 11, and 15 Internal Base: 21 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 15 is set to 0.*/ -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B15_DEFVAL -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B15_SHIFT -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B15_MASK -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B15_DEFVAL 0x00000000 -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B15_SHIFT 24 -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B15_MASK 0x0F000000U - -/*Selects the HIF address bit used as row address bit 14. Valid Range: 0 to 11, and 15 Internal Base: 20 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 14 is set to 0.*/ -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B14_DEFVAL -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B14_SHIFT -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B14_MASK -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B14_DEFVAL 0x00000000 -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B14_SHIFT 16 -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B14_MASK 0x000F0000U - -/*Selects the HIF address bit used as row address bit 13. Valid Range: 0 to 11, and 15 Internal Base: 19 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 13 is set to 0.*/ -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B13_DEFVAL -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B13_SHIFT -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B13_MASK -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B13_DEFVAL 0x00000000 -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B13_SHIFT 8 -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B13_MASK 0x00000F00U - -/*Selects the HIF address bit used as row address bit 12. Valid Range: 0 to 11, and 15 Internal Base: 18 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 12 is set to 0.*/ -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B12_DEFVAL -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B12_SHIFT -#undef DDRC_ADDRMAP6_ADDRMAP_ROW_B12_MASK -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B12_DEFVAL 0x00000000 -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B12_SHIFT 0 -#define DDRC_ADDRMAP6_ADDRMAP_ROW_B12_MASK 0x0000000FU - -/*Selects the HIF address bit used as row address bit 17. Valid Range: 0 to 10, and 15 Internal Base: 23 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 17 is set to 0.*/ -#undef DDRC_ADDRMAP7_ADDRMAP_ROW_B17_DEFVAL -#undef DDRC_ADDRMAP7_ADDRMAP_ROW_B17_SHIFT -#undef DDRC_ADDRMAP7_ADDRMAP_ROW_B17_MASK -#define DDRC_ADDRMAP7_ADDRMAP_ROW_B17_DEFVAL 0x00000000 -#define DDRC_ADDRMAP7_ADDRMAP_ROW_B17_SHIFT 8 -#define DDRC_ADDRMAP7_ADDRMAP_ROW_B17_MASK 0x00000F00U - -/*Selects the HIF address bit used as row address bit 16. Valid Range: 0 to 11, and 15 Internal Base: 22 The selected HIF addre - s bit is determined by adding the internal base to the value of this field. If set to 15, row address bit 16 is set to 0.*/ -#undef DDRC_ADDRMAP7_ADDRMAP_ROW_B16_DEFVAL -#undef DDRC_ADDRMAP7_ADDRMAP_ROW_B16_SHIFT -#undef DDRC_ADDRMAP7_ADDRMAP_ROW_B16_MASK -#define DDRC_ADDRMAP7_ADDRMAP_ROW_B16_DEFVAL 0x00000000 -#define DDRC_ADDRMAP7_ADDRMAP_ROW_B16_SHIFT 0 -#define DDRC_ADDRMAP7_ADDRMAP_ROW_B16_MASK 0x0000000FU - -/*Selects the HIF address bits used as bank group address bit 1. Valid Range: 0 to 30, and 31 Internal Base: 3 The selected HIF - address bit for each of the bank group address bits is determined by adding the internal base to the value of this field. If - et to 31, bank group address bit 1 is set to 0.*/ -#undef DDRC_ADDRMAP8_ADDRMAP_BG_B1_DEFVAL -#undef DDRC_ADDRMAP8_ADDRMAP_BG_B1_SHIFT -#undef DDRC_ADDRMAP8_ADDRMAP_BG_B1_MASK -#define DDRC_ADDRMAP8_ADDRMAP_BG_B1_DEFVAL 0x00000000 -#define DDRC_ADDRMAP8_ADDRMAP_BG_B1_SHIFT 8 -#define DDRC_ADDRMAP8_ADDRMAP_BG_B1_MASK 0x00001F00U - -/*Selects the HIF address bits used as bank group address bit 0. Valid Range: 0 to 30 Internal Base: 2 The selected HIF address - bit for each of the bank group address bits is determined by adding the internal base to the value of this field.*/ -#undef DDRC_ADDRMAP8_ADDRMAP_BG_B0_DEFVAL -#undef DDRC_ADDRMAP8_ADDRMAP_BG_B0_SHIFT -#undef DDRC_ADDRMAP8_ADDRMAP_BG_B0_MASK -#define DDRC_ADDRMAP8_ADDRMAP_BG_B0_DEFVAL 0x00000000 -#define DDRC_ADDRMAP8_ADDRMAP_BG_B0_SHIFT 0 -#define DDRC_ADDRMAP8_ADDRMAP_BG_B0_MASK 0x0000001FU - -/*Selects the HIF address bits used as row address bit 5. Valid Range: 0 to 11 Internal Base: 11 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.*/ -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B5_DEFVAL -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B5_SHIFT -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B5_MASK -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B5_DEFVAL 0x00000000 -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B5_SHIFT 24 -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B5_MASK 0x0F000000U - -/*Selects the HIF address bits used as row address bit 4. Valid Range: 0 to 11 Internal Base: 10 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.*/ -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B4_DEFVAL -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B4_SHIFT -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B4_MASK -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B4_DEFVAL 0x00000000 -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B4_SHIFT 16 -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B4_MASK 0x000F0000U - -/*Selects the HIF address bits used as row address bit 3. Valid Range: 0 to 11 Internal Base: 9 The selected HIF address bit fo - each of the row address bits is determined by adding the internal base to the value of this field. This register field is us - d only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.*/ -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B3_DEFVAL -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B3_SHIFT -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B3_MASK -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B3_DEFVAL 0x00000000 -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B3_SHIFT 8 -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B3_MASK 0x00000F00U - -/*Selects the HIF address bits used as row address bit 2. Valid Range: 0 to 11 Internal Base: 8 The selected HIF address bit fo - each of the row address bits is determined by adding the internal base to the value of this field. This register field is us - d only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.*/ -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B2_DEFVAL -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B2_SHIFT -#undef DDRC_ADDRMAP9_ADDRMAP_ROW_B2_MASK -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B2_DEFVAL 0x00000000 -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B2_SHIFT 0 -#define DDRC_ADDRMAP9_ADDRMAP_ROW_B2_MASK 0x0000000FU - -/*Selects the HIF address bits used as row address bit 9. Valid Range: 0 to 11 Internal Base: 15 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.*/ -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B9_DEFVAL -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B9_SHIFT -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B9_MASK -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B9_DEFVAL 0x00000000 -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B9_SHIFT 24 -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B9_MASK 0x0F000000U - -/*Selects the HIF address bits used as row address bit 8. Valid Range: 0 to 11 Internal Base: 14 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.*/ -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B8_DEFVAL -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B8_SHIFT -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B8_MASK -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B8_DEFVAL 0x00000000 -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B8_SHIFT 16 -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B8_MASK 0x000F0000U - -/*Selects the HIF address bits used as row address bit 7. Valid Range: 0 to 11 Internal Base: 13 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.*/ -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B7_DEFVAL -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B7_SHIFT -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B7_MASK -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B7_DEFVAL 0x00000000 -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B7_SHIFT 8 -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B7_MASK 0x00000F00U - -/*Selects the HIF address bits used as row address bit 6. Valid Range: 0 to 11 Internal Base: 12 The selected HIF address bit f - r each of the row address bits is determined by adding the internal base to the value of this field. This register field is u - ed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.*/ -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B6_DEFVAL -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B6_SHIFT -#undef DDRC_ADDRMAP10_ADDRMAP_ROW_B6_MASK -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B6_DEFVAL 0x00000000 -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B6_SHIFT 0 -#define DDRC_ADDRMAP10_ADDRMAP_ROW_B6_MASK 0x0000000FU - -/*Selects the HIF address bits used as row address bit 10. Valid Range: 0 to 11 Internal Base: 16 The selected HIF address bit - or each of the row address bits is determined by adding the internal base to the value of this field. This register field is - sed only when ADDRMAP5.addrmap_row_b2_10 is set to value 15.*/ -#undef DDRC_ADDRMAP11_ADDRMAP_ROW_B10_DEFVAL -#undef DDRC_ADDRMAP11_ADDRMAP_ROW_B10_SHIFT -#undef DDRC_ADDRMAP11_ADDRMAP_ROW_B10_MASK -#define DDRC_ADDRMAP11_ADDRMAP_ROW_B10_DEFVAL -#define DDRC_ADDRMAP11_ADDRMAP_ROW_B10_SHIFT 0 -#define DDRC_ADDRMAP11_ADDRMAP_ROW_B10_MASK 0x0000000FU - -/*Cycles to hold ODT for a write command. The minimum supported value is 2. Recommended values: DDR2: - BL8: 0x5 (DDR2-400/533/ - 67), 0x6 (DDR2-800), 0x7 (DDR2-1066) - BL4: 0x3 (DDR2-400/533/667), 0x4 (DDR2-800), 0x5 (DDR2-1066) DDR3: - BL8: 0x6 DDR4: - - L8: 5 + WR_PREAMBLE + CRC_MODE WR_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK write preamble) CRC_MODE = 0 (not CRC mode), 1 - CRC mode) LPDDR3: - BL8: 7 + RU(tODTon(max)/tCK)*/ -#undef DDRC_ODTCFG_WR_ODT_HOLD_DEFVAL -#undef DDRC_ODTCFG_WR_ODT_HOLD_SHIFT -#undef DDRC_ODTCFG_WR_ODT_HOLD_MASK -#define DDRC_ODTCFG_WR_ODT_HOLD_DEFVAL 0x04000400 -#define DDRC_ODTCFG_WR_ODT_HOLD_SHIFT 24 -#define DDRC_ODTCFG_WR_ODT_HOLD_MASK 0x0F000000U - -/*The delay, in clock cycles, from issuing a write command to setting ODT values associated with that command. ODT setting must - remain constant for the entire time that DQS is driven by the uMCTL2. Recommended values: DDR2: - CWL + AL - 3 (DDR2-400/533/ - 67), CWL + AL - 4 (DDR2-800), CWL + AL - 5 (DDR2-1066) If (CWL + AL - 3 < 0), uMCTL2 does not support ODT for write operation - DDR3: - 0x0 DDR4: - DFITMG1.dfi_t_cmd_lat (to adjust for CAL mode) LPDDR3: - WL - 1 - RU(tODTon(max)/tCK))*/ -#undef DDRC_ODTCFG_WR_ODT_DELAY_DEFVAL -#undef DDRC_ODTCFG_WR_ODT_DELAY_SHIFT -#undef DDRC_ODTCFG_WR_ODT_DELAY_MASK -#define DDRC_ODTCFG_WR_ODT_DELAY_DEFVAL 0x04000400 -#define DDRC_ODTCFG_WR_ODT_DELAY_SHIFT 16 -#define DDRC_ODTCFG_WR_ODT_DELAY_MASK 0x001F0000U - -/*Cycles to hold ODT for a read command. The minimum supported value is 2. Recommended values: DDR2: - BL8: 0x6 (not DDR2-1066) - 0x7 (DDR2-1066) - BL4: 0x4 (not DDR2-1066), 0x5 (DDR2-1066) DDR3: - BL8 - 0x6 DDR4: - BL8: 5 + RD_PREAMBLE RD_PREAMBLE = 1 ( - tCK write preamble), 2 (2tCK write preamble) LPDDR3: - BL8: 5 + RU(tDQSCK(max)/tCK) - RD(tDQSCK(min)/tCK) + RU(tODTon(max)/tC - )*/ -#undef DDRC_ODTCFG_RD_ODT_HOLD_DEFVAL -#undef DDRC_ODTCFG_RD_ODT_HOLD_SHIFT -#undef DDRC_ODTCFG_RD_ODT_HOLD_MASK -#define DDRC_ODTCFG_RD_ODT_HOLD_DEFVAL 0x04000400 -#define DDRC_ODTCFG_RD_ODT_HOLD_SHIFT 8 -#define DDRC_ODTCFG_RD_ODT_HOLD_MASK 0x00000F00U - -/*The delay, in clock cycles, from issuing a read command to setting ODT values associated with that command. ODT setting must - emain constant for the entire time that DQS is driven by the uMCTL2. Recommended values: DDR2: - CL + AL - 4 (not DDR2-1066), - CL + AL - 5 (DDR2-1066) If (CL + AL - 4 < 0), uMCTL2 does not support ODT for read operation. DDR3: - CL - CWL DDR4: - CL - C - L - RD_PREAMBLE + WR_PREAMBLE + DFITMG1.dfi_t_cmd_lat (to adjust for CAL mode) WR_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK - write preamble) RD_PREAMBLE = 1 (1tCK write preamble), 2 (2tCK write preamble) If (CL - CWL - RD_PREAMBLE + WR_PREAMBLE) < 0, - uMCTL2 does not support ODT for read operation. LPDDR3: - RL + RD(tDQSCK(min)/tCK) - 1 - RU(tODTon(max)/tCK)*/ -#undef DDRC_ODTCFG_RD_ODT_DELAY_DEFVAL -#undef DDRC_ODTCFG_RD_ODT_DELAY_SHIFT -#undef DDRC_ODTCFG_RD_ODT_DELAY_MASK -#define DDRC_ODTCFG_RD_ODT_DELAY_DEFVAL 0x04000400 -#define DDRC_ODTCFG_RD_ODT_DELAY_SHIFT 2 -#define DDRC_ODTCFG_RD_ODT_DELAY_MASK 0x0000007CU - -/*Indicates which remote ODTs must be turned on during a read from rank 1. Each rank has a remote ODT (in the SDRAM) which can - e turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB - etc. For each rank, set its bit to 1 to enable its ODT. Present only in configurations that have 2 or more ranks*/ -#undef DDRC_ODTMAP_RANK1_RD_ODT_DEFVAL -#undef DDRC_ODTMAP_RANK1_RD_ODT_SHIFT -#undef DDRC_ODTMAP_RANK1_RD_ODT_MASK -#define DDRC_ODTMAP_RANK1_RD_ODT_DEFVAL 0x00002211 -#define DDRC_ODTMAP_RANK1_RD_ODT_SHIFT 12 -#define DDRC_ODTMAP_RANK1_RD_ODT_MASK 0x00003000U - -/*Indicates which remote ODTs must be turned on during a write to rank 1. Each rank has a remote ODT (in the SDRAM) which can b - turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB, - etc. For each rank, set its bit to 1 to enable its ODT. Present only in configurations that have 2 or more ranks*/ -#undef DDRC_ODTMAP_RANK1_WR_ODT_DEFVAL -#undef DDRC_ODTMAP_RANK1_WR_ODT_SHIFT -#undef DDRC_ODTMAP_RANK1_WR_ODT_MASK -#define DDRC_ODTMAP_RANK1_WR_ODT_DEFVAL 0x00002211 -#define DDRC_ODTMAP_RANK1_WR_ODT_SHIFT 8 -#define DDRC_ODTMAP_RANK1_WR_ODT_MASK 0x00000300U - -/*Indicates which remote ODTs must be turned on during a read from rank 0. Each rank has a remote ODT (in the SDRAM) which can - e turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB - etc. For each rank, set its bit to 1 to enable its ODT.*/ -#undef DDRC_ODTMAP_RANK0_RD_ODT_DEFVAL -#undef DDRC_ODTMAP_RANK0_RD_ODT_SHIFT -#undef DDRC_ODTMAP_RANK0_RD_ODT_MASK -#define DDRC_ODTMAP_RANK0_RD_ODT_DEFVAL 0x00002211 -#define DDRC_ODTMAP_RANK0_RD_ODT_SHIFT 4 -#define DDRC_ODTMAP_RANK0_RD_ODT_MASK 0x00000030U - -/*Indicates which remote ODTs must be turned on during a write to rank 0. Each rank has a remote ODT (in the SDRAM) which can b - turned on by setting the appropriate bit here. Rank 0 is controlled by the LSB; rank 1 is controlled by bit next to the LSB, - etc. For each rank, set its bit to 1 to enable its ODT.*/ -#undef DDRC_ODTMAP_RANK0_WR_ODT_DEFVAL -#undef DDRC_ODTMAP_RANK0_WR_ODT_SHIFT -#undef DDRC_ODTMAP_RANK0_WR_ODT_MASK -#define DDRC_ODTMAP_RANK0_WR_ODT_DEFVAL 0x00002211 -#define DDRC_ODTMAP_RANK0_WR_ODT_SHIFT 0 -#define DDRC_ODTMAP_RANK0_WR_ODT_MASK 0x00000003U - -/*When the preferred transaction store is empty for these many clock cycles, switch to the alternate transaction store if it is - non-empty. The read transaction store (both high and low priority) is the default preferred transaction store and the write t - ansaction store is the alternative store. When prefer write over read is set this is reversed. 0x0 is a legal value for this - egister. When set to 0x0, the transaction store switching will happen immediately when the switching conditions become true. - OR PERFORMANCE ONLY*/ -#undef DDRC_SCHED_RDWR_IDLE_GAP_DEFVAL -#undef DDRC_SCHED_RDWR_IDLE_GAP_SHIFT -#undef DDRC_SCHED_RDWR_IDLE_GAP_MASK -#define DDRC_SCHED_RDWR_IDLE_GAP_DEFVAL 0x00002005 -#define DDRC_SCHED_RDWR_IDLE_GAP_SHIFT 24 -#define DDRC_SCHED_RDWR_IDLE_GAP_MASK 0x7F000000U - -/*UNUSED*/ -#undef DDRC_SCHED_GO2CRITICAL_HYSTERESIS_DEFVAL -#undef DDRC_SCHED_GO2CRITICAL_HYSTERESIS_SHIFT -#undef DDRC_SCHED_GO2CRITICAL_HYSTERESIS_MASK -#define DDRC_SCHED_GO2CRITICAL_HYSTERESIS_DEFVAL 0x00002005 -#define DDRC_SCHED_GO2CRITICAL_HYSTERESIS_SHIFT 16 -#define DDRC_SCHED_GO2CRITICAL_HYSTERESIS_MASK 0x00FF0000U - -/*Number of entries in the low priority transaction store is this value + 1. (MEMC_NO_OF_ENTRY - (SCHED.lpr_num_entries + 1)) i - the number of entries available for the high priority transaction store. Setting this to maximum value allocates all entries - to low priority transaction store. Setting this to 0 allocates 1 entry to low priority transaction store and the rest to high - priority transaction store. Note: In ECC configurations, the numbers of write and low priority read credits issued is one les - than in the non-ECC case. One entry each is reserved in the write and low-priority read CAMs for storing the RMW requests ar - sing out of single bit error correction RMW operation.*/ -#undef DDRC_SCHED_LPR_NUM_ENTRIES_DEFVAL -#undef DDRC_SCHED_LPR_NUM_ENTRIES_SHIFT -#undef DDRC_SCHED_LPR_NUM_ENTRIES_MASK -#define DDRC_SCHED_LPR_NUM_ENTRIES_DEFVAL 0x00002005 -#define DDRC_SCHED_LPR_NUM_ENTRIES_SHIFT 8 -#define DDRC_SCHED_LPR_NUM_ENTRIES_MASK 0x00003F00U - -/*If true, bank is kept open only while there are page hit transactions available in the CAM to that bank. The last read or wri - e command in the CAM with a bank and page hit will be executed with auto-precharge if SCHED1.pageclose_timer=0. Even if this - egister set to 1 and SCHED1.pageclose_timer is set to 0, explicit precharge (and not auto-precharge) may be issued in some ca - es where there is a mode switch between Write and Read or between LPR and HPR. The Read and Write commands that are executed - s part of the ECC scrub requests are also executed without auto-precharge. If false, the bank remains open until there is a n - ed to close it (to open a different page, or for page timeout or refresh timeout) - also known as open page policy. The open - age policy can be overridden by setting the per-command-autopre bit on the HIF interface (hif_cmd_autopre). The pageclose fea - ure provids a midway between Open and Close page policies. FOR PERFORMANCE ONLY.*/ -#undef DDRC_SCHED_PAGECLOSE_DEFVAL -#undef DDRC_SCHED_PAGECLOSE_SHIFT -#undef DDRC_SCHED_PAGECLOSE_MASK -#define DDRC_SCHED_PAGECLOSE_DEFVAL 0x00002005 -#define DDRC_SCHED_PAGECLOSE_SHIFT 2 -#define DDRC_SCHED_PAGECLOSE_MASK 0x00000004U - -/*If set then the bank selector prefers writes over reads. FOR DEBUG ONLY.*/ -#undef DDRC_SCHED_PREFER_WRITE_DEFVAL -#undef DDRC_SCHED_PREFER_WRITE_SHIFT -#undef DDRC_SCHED_PREFER_WRITE_MASK -#define DDRC_SCHED_PREFER_WRITE_DEFVAL 0x00002005 -#define DDRC_SCHED_PREFER_WRITE_SHIFT 1 -#define DDRC_SCHED_PREFER_WRITE_MASK 0x00000002U - -/*Active low signal. When asserted ('0'), all incoming transactions are forced to low priority. This implies that all High Prio - ity Read (HPR) and Variable Priority Read commands (VPR) will be treated as Low Priority Read (LPR) commands. On the write si - e, all Variable Priority Write (VPW) commands will be treated as Normal Priority Write (NPW) commands. Forcing the incoming t - ansactions to low priority implicitly turns off Bypass path for read commands. FOR PERFORMANCE ONLY.*/ -#undef DDRC_SCHED_FORCE_LOW_PRI_N_DEFVAL -#undef DDRC_SCHED_FORCE_LOW_PRI_N_SHIFT -#undef DDRC_SCHED_FORCE_LOW_PRI_N_MASK -#define DDRC_SCHED_FORCE_LOW_PRI_N_DEFVAL 0x00002005 -#define DDRC_SCHED_FORCE_LOW_PRI_N_SHIFT 0 -#define DDRC_SCHED_FORCE_LOW_PRI_N_MASK 0x00000001U - -/*Number of transactions that are serviced once the LPR queue goes critical is the smaller of: - (a) This number - (b) Number o - transactions available. Unit: Transaction. FOR PERFORMANCE ONLY.*/ -#undef DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH_DEFVAL -#undef DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH_SHIFT -#undef DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH_MASK -#define DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH_DEFVAL 0x0F00007F -#define DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH_SHIFT 24 -#define DDRC_PERFLPR1_LPR_XACT_RUN_LENGTH_MASK 0xFF000000U - -/*Number of clocks that the LPR queue can be starved before it goes critical. The minimum valid functional value for this regis - er is 0x1. Programming it to 0x0 will disable the starvation functionality; during normal operation, this function should not - be disabled as it will cause excessive latencies. Unit: Clock cycles. FOR PERFORMANCE ONLY.*/ -#undef DDRC_PERFLPR1_LPR_MAX_STARVE_DEFVAL -#undef DDRC_PERFLPR1_LPR_MAX_STARVE_SHIFT -#undef DDRC_PERFLPR1_LPR_MAX_STARVE_MASK -#define DDRC_PERFLPR1_LPR_MAX_STARVE_DEFVAL 0x0F00007F -#define DDRC_PERFLPR1_LPR_MAX_STARVE_SHIFT 0 -#define DDRC_PERFLPR1_LPR_MAX_STARVE_MASK 0x0000FFFFU - -/*Number of transactions that are serviced once the WR queue goes critical is the smaller of: - (a) This number - (b) Number of - transactions available. Unit: Transaction. FOR PERFORMANCE ONLY.*/ -#undef DDRC_PERFWR1_W_XACT_RUN_LENGTH_DEFVAL -#undef DDRC_PERFWR1_W_XACT_RUN_LENGTH_SHIFT -#undef DDRC_PERFWR1_W_XACT_RUN_LENGTH_MASK -#define DDRC_PERFWR1_W_XACT_RUN_LENGTH_DEFVAL 0x0F00007F -#define DDRC_PERFWR1_W_XACT_RUN_LENGTH_SHIFT 24 -#define DDRC_PERFWR1_W_XACT_RUN_LENGTH_MASK 0xFF000000U - -/*Number of clocks that the WR queue can be starved before it goes critical. The minimum valid functional value for this regist - r is 0x1. Programming it to 0x0 will disable the starvation functionality; during normal operation, this function should not - e disabled as it will cause excessive latencies. Unit: Clock cycles. FOR PERFORMANCE ONLY.*/ -#undef DDRC_PERFWR1_W_MAX_STARVE_DEFVAL -#undef DDRC_PERFWR1_W_MAX_STARVE_SHIFT -#undef DDRC_PERFWR1_W_MAX_STARVE_MASK -#define DDRC_PERFWR1_W_MAX_STARVE_DEFVAL 0x0F00007F -#define DDRC_PERFWR1_W_MAX_STARVE_SHIFT 0 -#define DDRC_PERFWR1_W_MAX_STARVE_MASK 0x0000FFFFU - -/*All even ranks have the same DQ mapping controled by DQMAP0-4 register as rank 0. This register provides DQ swap function for - all odd ranks to support CRC feature. rank based DQ swapping is: swap bit 0 with 1, swap bit 2 with 3, swap bit 4 with 5 and - wap bit 6 with 7. 1: Disable rank based DQ swapping 0: Enable rank based DQ swapping Present only in designs configured to su - port DDR4.*/ -#undef DDRC_DQMAP5_DIS_DQ_RANK_SWAP_DEFVAL -#undef DDRC_DQMAP5_DIS_DQ_RANK_SWAP_SHIFT -#undef DDRC_DQMAP5_DIS_DQ_RANK_SWAP_MASK -#define DDRC_DQMAP5_DIS_DQ_RANK_SWAP_DEFVAL -#define DDRC_DQMAP5_DIS_DQ_RANK_SWAP_SHIFT 0 -#define DDRC_DQMAP5_DIS_DQ_RANK_SWAP_MASK 0x00000001U - -/*When this is set to '0', auto-precharge is disabled for the flushed command in a collision case. Collision cases are write fo - lowed by read to same address, read followed by write to same address, or write followed by write to same address with DBG0.d - s_wc bit = 1 (where same address comparisons exclude the two address bits representing critical word). FOR DEBUG ONLY.*/ -#undef DDRC_DBG0_DIS_COLLISION_PAGE_OPT_DEFVAL -#undef DDRC_DBG0_DIS_COLLISION_PAGE_OPT_SHIFT -#undef DDRC_DBG0_DIS_COLLISION_PAGE_OPT_MASK -#define DDRC_DBG0_DIS_COLLISION_PAGE_OPT_DEFVAL 0x00000000 -#define DDRC_DBG0_DIS_COLLISION_PAGE_OPT_SHIFT 4 -#define DDRC_DBG0_DIS_COLLISION_PAGE_OPT_MASK 0x00000010U - -/*When 1, disable write combine. FOR DEBUG ONLY*/ -#undef DDRC_DBG0_DIS_WC_DEFVAL -#undef DDRC_DBG0_DIS_WC_SHIFT -#undef DDRC_DBG0_DIS_WC_MASK -#define DDRC_DBG0_DIS_WC_DEFVAL 0x00000000 -#define DDRC_DBG0_DIS_WC_SHIFT 0 -#define DDRC_DBG0_DIS_WC_MASK 0x00000001U - -/*Setting this register bit to 1 allows refresh and ZQCS commands to be triggered from hardware via the IOs ext_*. If set to 1, - the fields DBGCMD.zq_calib_short and DBGCMD.rank*_refresh have no function, and are ignored by the uMCTL2 logic. Setting this - register bit to 0 allows refresh and ZQCS to be triggered from software, via the fields DBGCMD.zq_calib_short and DBGCMD.rank - _refresh. If set to 0, the hardware pins ext_* have no function, and are ignored by the uMCTL2 logic. This register is static - and may only be changed when the DDRC reset signal, core_ddrc_rstn, is asserted (0).*/ -#undef DDRC_DBGCMD_HW_REF_ZQ_EN_DEFVAL -#undef DDRC_DBGCMD_HW_REF_ZQ_EN_SHIFT -#undef DDRC_DBGCMD_HW_REF_ZQ_EN_MASK -#define DDRC_DBGCMD_HW_REF_ZQ_EN_DEFVAL 0x00000000 -#define DDRC_DBGCMD_HW_REF_ZQ_EN_SHIFT 31 -#define DDRC_DBGCMD_HW_REF_ZQ_EN_MASK 0x80000000U - -/*Setting this register bit to 1 indicates to the uMCTL2 to issue a dfi_ctrlupd_req to the PHY. When this request is stored in - he uMCTL2, the bit is automatically cleared. This operation must only be performed when DFIUPD0.dis_auto_ctrlupd=1.*/ -#undef DDRC_DBGCMD_CTRLUPD_DEFVAL -#undef DDRC_DBGCMD_CTRLUPD_SHIFT -#undef DDRC_DBGCMD_CTRLUPD_MASK -#define DDRC_DBGCMD_CTRLUPD_DEFVAL 0x00000000 -#define DDRC_DBGCMD_CTRLUPD_SHIFT 5 -#define DDRC_DBGCMD_CTRLUPD_MASK 0x00000020U - -/*Setting this register bit to 1 indicates to the uMCTL2 to issue a ZQCS (ZQ calibration short)/MPC(ZQ calibration) command to - he SDRAM. When this request is stored in the uMCTL2, the bit is automatically cleared. This operation can be performed only w - en ZQCTL0.dis_auto_zq=1. It is recommended NOT to set this register bit if in Init operating mode. This register bit is ignor - d when in Self-Refresh(except LPDDR4) and SR-Powerdown(LPDDR4) and Deep power-down operating modes and Maximum Power Saving M - de.*/ -#undef DDRC_DBGCMD_ZQ_CALIB_SHORT_DEFVAL -#undef DDRC_DBGCMD_ZQ_CALIB_SHORT_SHIFT -#undef DDRC_DBGCMD_ZQ_CALIB_SHORT_MASK -#define DDRC_DBGCMD_ZQ_CALIB_SHORT_DEFVAL 0x00000000 -#define DDRC_DBGCMD_ZQ_CALIB_SHORT_SHIFT 4 -#define DDRC_DBGCMD_ZQ_CALIB_SHORT_MASK 0x00000010U - -/*Setting this register bit to 1 indicates to the uMCTL2 to issue a refresh to rank 1. Writing to this bit causes DBGSTAT.rank1 - refresh_busy to be set. When DBGSTAT.rank1_refresh_busy is cleared, the command has been stored in uMCTL2. This operation can - be performed only when RFSHCTL3.dis_auto_refresh=1. It is recommended NOT to set this register bit if in Init or Deep power-d - wn operating modes or Maximum Power Saving Mode.*/ -#undef DDRC_DBGCMD_RANK1_REFRESH_DEFVAL -#undef DDRC_DBGCMD_RANK1_REFRESH_SHIFT -#undef DDRC_DBGCMD_RANK1_REFRESH_MASK -#define DDRC_DBGCMD_RANK1_REFRESH_DEFVAL 0x00000000 -#define DDRC_DBGCMD_RANK1_REFRESH_SHIFT 1 -#define DDRC_DBGCMD_RANK1_REFRESH_MASK 0x00000002U - -/*Setting this register bit to 1 indicates to the uMCTL2 to issue a refresh to rank 0. Writing to this bit causes DBGSTAT.rank0 - refresh_busy to be set. When DBGSTAT.rank0_refresh_busy is cleared, the command has been stored in uMCTL2. This operation can - be performed only when RFSHCTL3.dis_auto_refresh=1. It is recommended NOT to set this register bit if in Init or Deep power-d - wn operating modes or Maximum Power Saving Mode.*/ -#undef DDRC_DBGCMD_RANK0_REFRESH_DEFVAL -#undef DDRC_DBGCMD_RANK0_REFRESH_SHIFT -#undef DDRC_DBGCMD_RANK0_REFRESH_MASK -#define DDRC_DBGCMD_RANK0_REFRESH_DEFVAL 0x00000000 -#define DDRC_DBGCMD_RANK0_REFRESH_SHIFT 0 -#define DDRC_DBGCMD_RANK0_REFRESH_MASK 0x00000001U - -/*Enable quasi-dynamic register programming outside reset. Program register to 0 to enable quasi-dynamic programming. Set back - egister to 1 once programming is done.*/ -#undef DDRC_SWCTL_SW_DONE_DEFVAL -#undef DDRC_SWCTL_SW_DONE_SHIFT -#undef DDRC_SWCTL_SW_DONE_MASK -#define DDRC_SWCTL_SW_DONE_DEFVAL -#define DDRC_SWCTL_SW_DONE_SHIFT 0 -#define DDRC_SWCTL_SW_DONE_MASK 0x00000001U - -/*Burst length expansion mode. By default (i.e. bl_exp_mode==0) XPI expands every AXI burst into multiple HIF commands, using t - e memory burst length as a unit. If set to 1, then XPI will use half of the memory burst length as a unit. This applies to bo - h reads and writes. When MSTR.data_bus_width==00, setting bl_exp_mode to 1 has no effect. This can be used in cases where Par - ial Writes is enabled (UMCTL2_PARTIAL_WR=1) and DBG0.dis_wc=1, in order to avoid or minimize t_ccd_l penalty in DDR4 and t_cc - _mw penalty in LPDDR4. Note that if DBICTL.reg_ddrc_dm_en=0, functionality is not supported in the following cases: - UMCTL2_ - ARTIAL_WR=0 - UMCTL2_PARTIAL_WR=1, MSTR.reg_ddrc_data_bus_width=01, MEMC_BURST_LENGTH=8 and MSTR.reg_ddrc_burst_rdwr=1000 (LP - DR4 only) - UMCTL2_PARTIAL_WR=1, MSTR.reg_ddrc_data_bus_width=01, MEMC_BURST_LENGTH=4 and MSTR.reg_ddrc_burst_rdwr=0100 (DDR4 - only), with either MSTR.reg_ddrc_burstchop=0 or CRCPARCTL1.reg_ddrc_crc_enable=1 Functionality is also not supported if Share - -AC is enabled*/ -#undef DDRC_PCCFG_BL_EXP_MODE_DEFVAL -#undef DDRC_PCCFG_BL_EXP_MODE_SHIFT -#undef DDRC_PCCFG_BL_EXP_MODE_MASK -#define DDRC_PCCFG_BL_EXP_MODE_DEFVAL 0x00000000 -#define DDRC_PCCFG_BL_EXP_MODE_SHIFT 8 -#define DDRC_PCCFG_BL_EXP_MODE_MASK 0x00000100U - -/*Page match four limit. If set to 1, limits the number of consecutive same page DDRC transactions that can be granted by the P - rt Arbiter to four when Page Match feature is enabled. If set to 0, there is no limit imposed on number of consecutive same p - ge DDRC transactions.*/ -#undef DDRC_PCCFG_PAGEMATCH_LIMIT_DEFVAL -#undef DDRC_PCCFG_PAGEMATCH_LIMIT_SHIFT -#undef DDRC_PCCFG_PAGEMATCH_LIMIT_MASK -#define DDRC_PCCFG_PAGEMATCH_LIMIT_DEFVAL 0x00000000 -#define DDRC_PCCFG_PAGEMATCH_LIMIT_SHIFT 4 -#define DDRC_PCCFG_PAGEMATCH_LIMIT_MASK 0x00000010U - -/*If set to 1 (enabled), sets co_gs_go2critical_wr and co_gs_go2critical_lpr/co_gs_go2critical_hpr signals going to DDRC based - n urgent input (awurgent, arurgent) coming from AXI master. If set to 0 (disabled), co_gs_go2critical_wr and co_gs_go2critica - _lpr/co_gs_go2critical_hpr signals at DDRC are driven to 1b'0.*/ -#undef DDRC_PCCFG_GO2CRITICAL_EN_DEFVAL -#undef DDRC_PCCFG_GO2CRITICAL_EN_SHIFT -#undef DDRC_PCCFG_GO2CRITICAL_EN_MASK -#define DDRC_PCCFG_GO2CRITICAL_EN_DEFVAL 0x00000000 -#define DDRC_PCCFG_GO2CRITICAL_EN_SHIFT 0 -#define DDRC_PCCFG_GO2CRITICAL_EN_MASK 0x00000001U - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGR_0_RD_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command).*/ -#undef DDRC_PCFGR_0_RD_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGR_0_RD_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGR_0_RD_PORT_URGENT_EN_MASK -#define DDRC_PCFGR_0_RD_PORT_URGENT_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_0_RD_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGR_0_RD_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the read channel of the port.*/ -#undef DDRC_PCFGR_0_RD_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGR_0_RD_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGR_0_RD_PORT_AGING_EN_MASK -#define DDRC_PCFGR_0_RD_PORT_AGING_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_0_RD_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGR_0_RD_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGR_0_RD_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGR_0_RD_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGR_0_RD_PORT_PRIORITY_MASK -#define DDRC_PCFGR_0_RD_PORT_PRIORITY_DEFVAL 0x00000000 -#define DDRC_PCFGR_0_RD_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGR_0_RD_PORT_PRIORITY_MASK 0x000003FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGW_0_WR_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command).*/ -#undef DDRC_PCFGW_0_WR_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGW_0_WR_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGW_0_WR_PORT_URGENT_EN_MASK -#define DDRC_PCFGW_0_WR_PORT_URGENT_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_0_WR_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGW_0_WR_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the write channel of the port.*/ -#undef DDRC_PCFGW_0_WR_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGW_0_WR_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGW_0_WR_PORT_AGING_EN_MASK -#define DDRC_PCFGW_0_WR_PORT_AGING_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_0_WR_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGW_0_WR_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGW_0_WR_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGW_0_WR_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGW_0_WR_PORT_PRIORITY_MASK -#define DDRC_PCFGW_0_WR_PORT_PRIORITY_DEFVAL 0x00004000 -#define DDRC_PCFGW_0_WR_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGW_0_WR_PORT_PRIORITY_MASK 0x000003FFU - -/*Enables port n.*/ -#undef DDRC_PCTRL_0_PORT_EN_DEFVAL -#undef DDRC_PCTRL_0_PORT_EN_SHIFT -#undef DDRC_PCTRL_0_PORT_EN_MASK -#define DDRC_PCTRL_0_PORT_EN_DEFVAL -#define DDRC_PCTRL_0_PORT_EN_SHIFT 0 -#define DDRC_PCTRL_0_PORT_EN_MASK 0x00000001U - -/*This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_0_RQOS_MAP_REGION1_DEFVAL -#undef DDRC_PCFGQOS0_0_RQOS_MAP_REGION1_SHIFT -#undef DDRC_PCFGQOS0_0_RQOS_MAP_REGION1_MASK -#define DDRC_PCFGQOS0_0_RQOS_MAP_REGION1_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_0_RQOS_MAP_REGION1_SHIFT 20 -#define DDRC_PCFGQOS0_0_RQOS_MAP_REGION1_MASK 0x00300000U - -/*This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_0_RQOS_MAP_REGION0_DEFVAL -#undef DDRC_PCFGQOS0_0_RQOS_MAP_REGION0_SHIFT -#undef DDRC_PCFGQOS0_0_RQOS_MAP_REGION0_MASK -#define DDRC_PCFGQOS0_0_RQOS_MAP_REGION0_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_0_RQOS_MAP_REGION0_SHIFT 16 -#define DDRC_PCFGQOS0_0_RQOS_MAP_REGION0_MASK 0x00030000U - -/*Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values.*/ -#undef DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1_DEFVAL -#undef DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1_SHIFT -#undef DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1_MASK -#define DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1_SHIFT 0 -#define DDRC_PCFGQOS0_0_RQOS_MAP_LEVEL1_MASK 0x0000000FU - -/*Specifies the timeout value for transactions mapped to the red address queue.*/ -#undef DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR_DEFVAL -#undef DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR_SHIFT -#undef DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR_MASK -#define DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR_SHIFT 16 -#define DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTR_MASK 0x07FF0000U - -/*Specifies the timeout value for transactions mapped to the blue address queue.*/ -#undef DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB_DEFVAL -#undef DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB_SHIFT -#undef DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB_MASK -#define DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB_SHIFT 0 -#define DDRC_PCFGQOS1_0_RQOS_MAP_TIMEOUTB_MASK 0x000007FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGR_1_RD_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command).*/ -#undef DDRC_PCFGR_1_RD_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGR_1_RD_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGR_1_RD_PORT_URGENT_EN_MASK -#define DDRC_PCFGR_1_RD_PORT_URGENT_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_1_RD_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGR_1_RD_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the read channel of the port.*/ -#undef DDRC_PCFGR_1_RD_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGR_1_RD_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGR_1_RD_PORT_AGING_EN_MASK -#define DDRC_PCFGR_1_RD_PORT_AGING_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_1_RD_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGR_1_RD_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGR_1_RD_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGR_1_RD_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGR_1_RD_PORT_PRIORITY_MASK -#define DDRC_PCFGR_1_RD_PORT_PRIORITY_DEFVAL 0x00000000 -#define DDRC_PCFGR_1_RD_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGR_1_RD_PORT_PRIORITY_MASK 0x000003FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGW_1_WR_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command).*/ -#undef DDRC_PCFGW_1_WR_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGW_1_WR_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGW_1_WR_PORT_URGENT_EN_MASK -#define DDRC_PCFGW_1_WR_PORT_URGENT_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_1_WR_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGW_1_WR_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the write channel of the port.*/ -#undef DDRC_PCFGW_1_WR_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGW_1_WR_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGW_1_WR_PORT_AGING_EN_MASK -#define DDRC_PCFGW_1_WR_PORT_AGING_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_1_WR_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGW_1_WR_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGW_1_WR_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGW_1_WR_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGW_1_WR_PORT_PRIORITY_MASK -#define DDRC_PCFGW_1_WR_PORT_PRIORITY_DEFVAL 0x00004000 -#define DDRC_PCFGW_1_WR_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGW_1_WR_PORT_PRIORITY_MASK 0x000003FFU - -/*Enables port n.*/ -#undef DDRC_PCTRL_1_PORT_EN_DEFVAL -#undef DDRC_PCTRL_1_PORT_EN_SHIFT -#undef DDRC_PCTRL_1_PORT_EN_MASK -#define DDRC_PCTRL_1_PORT_EN_DEFVAL -#define DDRC_PCTRL_1_PORT_EN_SHIFT 0 -#define DDRC_PCTRL_1_PORT_EN_MASK 0x00000001U - -/*This bitfield indicates the traffic class of region2. For dual address queue configurations, region2 maps to the red address - ueue. Valid values are 1: VPR and 2: HPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and traffic class of region2 - s set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_1_RQOS_MAP_REGION2_DEFVAL -#undef DDRC_PCFGQOS0_1_RQOS_MAP_REGION2_SHIFT -#undef DDRC_PCFGQOS0_1_RQOS_MAP_REGION2_MASK -#define DDRC_PCFGQOS0_1_RQOS_MAP_REGION2_DEFVAL 0x02000E00 -#define DDRC_PCFGQOS0_1_RQOS_MAP_REGION2_SHIFT 24 -#define DDRC_PCFGQOS0_1_RQOS_MAP_REGION2_MASK 0x03000000U - -/*This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_1_RQOS_MAP_REGION1_DEFVAL -#undef DDRC_PCFGQOS0_1_RQOS_MAP_REGION1_SHIFT -#undef DDRC_PCFGQOS0_1_RQOS_MAP_REGION1_MASK -#define DDRC_PCFGQOS0_1_RQOS_MAP_REGION1_DEFVAL 0x02000E00 -#define DDRC_PCFGQOS0_1_RQOS_MAP_REGION1_SHIFT 20 -#define DDRC_PCFGQOS0_1_RQOS_MAP_REGION1_MASK 0x00300000U - -/*This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_1_RQOS_MAP_REGION0_DEFVAL -#undef DDRC_PCFGQOS0_1_RQOS_MAP_REGION0_SHIFT -#undef DDRC_PCFGQOS0_1_RQOS_MAP_REGION0_MASK -#define DDRC_PCFGQOS0_1_RQOS_MAP_REGION0_DEFVAL 0x02000E00 -#define DDRC_PCFGQOS0_1_RQOS_MAP_REGION0_SHIFT 16 -#define DDRC_PCFGQOS0_1_RQOS_MAP_REGION0_MASK 0x00030000U - -/*Separation level2 indicating the end of region1 mapping; start of region1 is (level1 + 1). Possible values for level2 are (le - el1 + 1) to 14 which corresponds to arqos. Region2 starts from (level2 + 1) up to 15. Note that for PA, arqos values are used - directly as port priorities, where the higher the value corresponds to higher port priority. All of the map_level* registers - ust be set to distinct values.*/ -#undef DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2_DEFVAL -#undef DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2_SHIFT -#undef DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2_MASK -#define DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2_DEFVAL 0x02000E00 -#define DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2_SHIFT 8 -#define DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL2_MASK 0x00000F00U - -/*Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values.*/ -#undef DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1_DEFVAL -#undef DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1_SHIFT -#undef DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1_MASK -#define DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1_DEFVAL 0x02000E00 -#define DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1_SHIFT 0 -#define DDRC_PCFGQOS0_1_RQOS_MAP_LEVEL1_MASK 0x0000000FU - -/*Specifies the timeout value for transactions mapped to the red address queue.*/ -#undef DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR_DEFVAL -#undef DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR_SHIFT -#undef DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR_MASK -#define DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR_SHIFT 16 -#define DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTR_MASK 0x07FF0000U - -/*Specifies the timeout value for transactions mapped to the blue address queue.*/ -#undef DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB_DEFVAL -#undef DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB_SHIFT -#undef DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB_MASK -#define DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB_SHIFT 0 -#define DDRC_PCFGQOS1_1_RQOS_MAP_TIMEOUTB_MASK 0x000007FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGR_2_RD_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command).*/ -#undef DDRC_PCFGR_2_RD_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGR_2_RD_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGR_2_RD_PORT_URGENT_EN_MASK -#define DDRC_PCFGR_2_RD_PORT_URGENT_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_2_RD_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGR_2_RD_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the read channel of the port.*/ -#undef DDRC_PCFGR_2_RD_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGR_2_RD_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGR_2_RD_PORT_AGING_EN_MASK -#define DDRC_PCFGR_2_RD_PORT_AGING_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_2_RD_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGR_2_RD_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGR_2_RD_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGR_2_RD_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGR_2_RD_PORT_PRIORITY_MASK -#define DDRC_PCFGR_2_RD_PORT_PRIORITY_DEFVAL 0x00000000 -#define DDRC_PCFGR_2_RD_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGR_2_RD_PORT_PRIORITY_MASK 0x000003FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGW_2_WR_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command).*/ -#undef DDRC_PCFGW_2_WR_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGW_2_WR_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGW_2_WR_PORT_URGENT_EN_MASK -#define DDRC_PCFGW_2_WR_PORT_URGENT_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_2_WR_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGW_2_WR_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the write channel of the port.*/ -#undef DDRC_PCFGW_2_WR_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGW_2_WR_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGW_2_WR_PORT_AGING_EN_MASK -#define DDRC_PCFGW_2_WR_PORT_AGING_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_2_WR_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGW_2_WR_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGW_2_WR_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGW_2_WR_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGW_2_WR_PORT_PRIORITY_MASK -#define DDRC_PCFGW_2_WR_PORT_PRIORITY_DEFVAL 0x00004000 -#define DDRC_PCFGW_2_WR_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGW_2_WR_PORT_PRIORITY_MASK 0x000003FFU - -/*Enables port n.*/ -#undef DDRC_PCTRL_2_PORT_EN_DEFVAL -#undef DDRC_PCTRL_2_PORT_EN_SHIFT -#undef DDRC_PCTRL_2_PORT_EN_MASK -#define DDRC_PCTRL_2_PORT_EN_DEFVAL -#define DDRC_PCTRL_2_PORT_EN_SHIFT 0 -#define DDRC_PCTRL_2_PORT_EN_MASK 0x00000001U - -/*This bitfield indicates the traffic class of region2. For dual address queue configurations, region2 maps to the red address - ueue. Valid values are 1: VPR and 2: HPR only. When VPR support is disabled (UMCTL2_VPR_EN = 0) and traffic class of region2 - s set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_2_RQOS_MAP_REGION2_DEFVAL -#undef DDRC_PCFGQOS0_2_RQOS_MAP_REGION2_SHIFT -#undef DDRC_PCFGQOS0_2_RQOS_MAP_REGION2_MASK -#define DDRC_PCFGQOS0_2_RQOS_MAP_REGION2_DEFVAL 0x02000E00 -#define DDRC_PCFGQOS0_2_RQOS_MAP_REGION2_SHIFT 24 -#define DDRC_PCFGQOS0_2_RQOS_MAP_REGION2_MASK 0x03000000U - -/*This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_2_RQOS_MAP_REGION1_DEFVAL -#undef DDRC_PCFGQOS0_2_RQOS_MAP_REGION1_SHIFT -#undef DDRC_PCFGQOS0_2_RQOS_MAP_REGION1_MASK -#define DDRC_PCFGQOS0_2_RQOS_MAP_REGION1_DEFVAL 0x02000E00 -#define DDRC_PCFGQOS0_2_RQOS_MAP_REGION1_SHIFT 20 -#define DDRC_PCFGQOS0_2_RQOS_MAP_REGION1_MASK 0x00300000U - -/*This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_2_RQOS_MAP_REGION0_DEFVAL -#undef DDRC_PCFGQOS0_2_RQOS_MAP_REGION0_SHIFT -#undef DDRC_PCFGQOS0_2_RQOS_MAP_REGION0_MASK -#define DDRC_PCFGQOS0_2_RQOS_MAP_REGION0_DEFVAL 0x02000E00 -#define DDRC_PCFGQOS0_2_RQOS_MAP_REGION0_SHIFT 16 -#define DDRC_PCFGQOS0_2_RQOS_MAP_REGION0_MASK 0x00030000U - -/*Separation level2 indicating the end of region1 mapping; start of region1 is (level1 + 1). Possible values for level2 are (le - el1 + 1) to 14 which corresponds to arqos. Region2 starts from (level2 + 1) up to 15. Note that for PA, arqos values are used - directly as port priorities, where the higher the value corresponds to higher port priority. All of the map_level* registers - ust be set to distinct values.*/ -#undef DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2_DEFVAL -#undef DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2_SHIFT -#undef DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2_MASK -#define DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2_DEFVAL 0x02000E00 -#define DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2_SHIFT 8 -#define DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL2_MASK 0x00000F00U - -/*Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values.*/ -#undef DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1_DEFVAL -#undef DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1_SHIFT -#undef DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1_MASK -#define DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1_DEFVAL 0x02000E00 -#define DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1_SHIFT 0 -#define DDRC_PCFGQOS0_2_RQOS_MAP_LEVEL1_MASK 0x0000000FU - -/*Specifies the timeout value for transactions mapped to the red address queue.*/ -#undef DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR_DEFVAL -#undef DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR_SHIFT -#undef DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR_MASK -#define DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR_SHIFT 16 -#define DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTR_MASK 0x07FF0000U - -/*Specifies the timeout value for transactions mapped to the blue address queue.*/ -#undef DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB_DEFVAL -#undef DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB_SHIFT -#undef DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB_MASK -#define DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB_SHIFT 0 -#define DDRC_PCFGQOS1_2_RQOS_MAP_TIMEOUTB_MASK 0x000007FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGR_3_RD_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command).*/ -#undef DDRC_PCFGR_3_RD_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGR_3_RD_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGR_3_RD_PORT_URGENT_EN_MASK -#define DDRC_PCFGR_3_RD_PORT_URGENT_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_3_RD_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGR_3_RD_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the read channel of the port.*/ -#undef DDRC_PCFGR_3_RD_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGR_3_RD_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGR_3_RD_PORT_AGING_EN_MASK -#define DDRC_PCFGR_3_RD_PORT_AGING_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_3_RD_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGR_3_RD_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGR_3_RD_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGR_3_RD_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGR_3_RD_PORT_PRIORITY_MASK -#define DDRC_PCFGR_3_RD_PORT_PRIORITY_DEFVAL 0x00000000 -#define DDRC_PCFGR_3_RD_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGR_3_RD_PORT_PRIORITY_MASK 0x000003FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGW_3_WR_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command).*/ -#undef DDRC_PCFGW_3_WR_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGW_3_WR_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGW_3_WR_PORT_URGENT_EN_MASK -#define DDRC_PCFGW_3_WR_PORT_URGENT_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_3_WR_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGW_3_WR_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the write channel of the port.*/ -#undef DDRC_PCFGW_3_WR_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGW_3_WR_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGW_3_WR_PORT_AGING_EN_MASK -#define DDRC_PCFGW_3_WR_PORT_AGING_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_3_WR_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGW_3_WR_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGW_3_WR_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGW_3_WR_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGW_3_WR_PORT_PRIORITY_MASK -#define DDRC_PCFGW_3_WR_PORT_PRIORITY_DEFVAL 0x00004000 -#define DDRC_PCFGW_3_WR_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGW_3_WR_PORT_PRIORITY_MASK 0x000003FFU - -/*Enables port n.*/ -#undef DDRC_PCTRL_3_PORT_EN_DEFVAL -#undef DDRC_PCTRL_3_PORT_EN_SHIFT -#undef DDRC_PCTRL_3_PORT_EN_MASK -#define DDRC_PCTRL_3_PORT_EN_DEFVAL -#define DDRC_PCTRL_3_PORT_EN_SHIFT 0 -#define DDRC_PCTRL_3_PORT_EN_MASK 0x00000001U - -/*This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_3_RQOS_MAP_REGION1_DEFVAL -#undef DDRC_PCFGQOS0_3_RQOS_MAP_REGION1_SHIFT -#undef DDRC_PCFGQOS0_3_RQOS_MAP_REGION1_MASK -#define DDRC_PCFGQOS0_3_RQOS_MAP_REGION1_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_3_RQOS_MAP_REGION1_SHIFT 20 -#define DDRC_PCFGQOS0_3_RQOS_MAP_REGION1_MASK 0x00300000U - -/*This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_3_RQOS_MAP_REGION0_DEFVAL -#undef DDRC_PCFGQOS0_3_RQOS_MAP_REGION0_SHIFT -#undef DDRC_PCFGQOS0_3_RQOS_MAP_REGION0_MASK -#define DDRC_PCFGQOS0_3_RQOS_MAP_REGION0_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_3_RQOS_MAP_REGION0_SHIFT 16 -#define DDRC_PCFGQOS0_3_RQOS_MAP_REGION0_MASK 0x00030000U - -/*Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values.*/ -#undef DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1_DEFVAL -#undef DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1_SHIFT -#undef DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1_MASK -#define DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1_SHIFT 0 -#define DDRC_PCFGQOS0_3_RQOS_MAP_LEVEL1_MASK 0x0000000FU - -/*Specifies the timeout value for transactions mapped to the red address queue.*/ -#undef DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR_DEFVAL -#undef DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR_SHIFT -#undef DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR_MASK -#define DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR_SHIFT 16 -#define DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTR_MASK 0x07FF0000U - -/*Specifies the timeout value for transactions mapped to the blue address queue.*/ -#undef DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB_DEFVAL -#undef DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB_SHIFT -#undef DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB_MASK -#define DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB_SHIFT 0 -#define DDRC_PCFGQOS1_3_RQOS_MAP_TIMEOUTB_MASK 0x000007FFU - -/*This bitfield indicates the traffic class of region 1. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW traffic.*/ -#undef DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1_DEFVAL -#undef DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1_SHIFT -#undef DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1_MASK -#define DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1_DEFVAL 0x00000000 -#define DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1_SHIFT 20 -#define DDRC_PCFGWQOS0_3_WQOS_MAP_REGION1_MASK 0x00300000U - -/*This bitfield indicates the traffic class of region 0. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW traffic.*/ -#undef DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0_DEFVAL -#undef DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0_SHIFT -#undef DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0_MASK -#define DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0_DEFVAL 0x00000000 -#define DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0_SHIFT 16 -#define DDRC_PCFGWQOS0_3_WQOS_MAP_REGION0_MASK 0x00030000U - -/*Separation level indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 14 which c - rresponds to awqos. Note that for PA, awqos values are used directly as port priorities, where the higher the value correspon - s to higher port priority.*/ -#undef DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL_DEFVAL -#undef DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL_SHIFT -#undef DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL_MASK -#define DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL_DEFVAL 0x00000000 -#define DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL_SHIFT 0 -#define DDRC_PCFGWQOS0_3_WQOS_MAP_LEVEL_MASK 0x0000000FU - -/*Specifies the timeout value for write transactions.*/ -#undef DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT_DEFVAL -#undef DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT_SHIFT -#undef DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT_MASK -#define DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT_DEFVAL -#define DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT_SHIFT 0 -#define DDRC_PCFGWQOS1_3_WQOS_MAP_TIMEOUT_MASK 0x000007FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGR_4_RD_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command).*/ -#undef DDRC_PCFGR_4_RD_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGR_4_RD_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGR_4_RD_PORT_URGENT_EN_MASK -#define DDRC_PCFGR_4_RD_PORT_URGENT_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_4_RD_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGR_4_RD_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the read channel of the port.*/ -#undef DDRC_PCFGR_4_RD_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGR_4_RD_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGR_4_RD_PORT_AGING_EN_MASK -#define DDRC_PCFGR_4_RD_PORT_AGING_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_4_RD_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGR_4_RD_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGR_4_RD_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGR_4_RD_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGR_4_RD_PORT_PRIORITY_MASK -#define DDRC_PCFGR_4_RD_PORT_PRIORITY_DEFVAL 0x00000000 -#define DDRC_PCFGR_4_RD_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGR_4_RD_PORT_PRIORITY_MASK 0x000003FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGW_4_WR_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command).*/ -#undef DDRC_PCFGW_4_WR_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGW_4_WR_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGW_4_WR_PORT_URGENT_EN_MASK -#define DDRC_PCFGW_4_WR_PORT_URGENT_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_4_WR_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGW_4_WR_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the write channel of the port.*/ -#undef DDRC_PCFGW_4_WR_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGW_4_WR_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGW_4_WR_PORT_AGING_EN_MASK -#define DDRC_PCFGW_4_WR_PORT_AGING_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_4_WR_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGW_4_WR_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGW_4_WR_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGW_4_WR_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGW_4_WR_PORT_PRIORITY_MASK -#define DDRC_PCFGW_4_WR_PORT_PRIORITY_DEFVAL 0x00004000 -#define DDRC_PCFGW_4_WR_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGW_4_WR_PORT_PRIORITY_MASK 0x000003FFU - -/*Enables port n.*/ -#undef DDRC_PCTRL_4_PORT_EN_DEFVAL -#undef DDRC_PCTRL_4_PORT_EN_SHIFT -#undef DDRC_PCTRL_4_PORT_EN_MASK -#define DDRC_PCTRL_4_PORT_EN_DEFVAL -#define DDRC_PCTRL_4_PORT_EN_SHIFT 0 -#define DDRC_PCTRL_4_PORT_EN_MASK 0x00000001U - -/*This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_4_RQOS_MAP_REGION1_DEFVAL -#undef DDRC_PCFGQOS0_4_RQOS_MAP_REGION1_SHIFT -#undef DDRC_PCFGQOS0_4_RQOS_MAP_REGION1_MASK -#define DDRC_PCFGQOS0_4_RQOS_MAP_REGION1_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_4_RQOS_MAP_REGION1_SHIFT 20 -#define DDRC_PCFGQOS0_4_RQOS_MAP_REGION1_MASK 0x00300000U - -/*This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_4_RQOS_MAP_REGION0_DEFVAL -#undef DDRC_PCFGQOS0_4_RQOS_MAP_REGION0_SHIFT -#undef DDRC_PCFGQOS0_4_RQOS_MAP_REGION0_MASK -#define DDRC_PCFGQOS0_4_RQOS_MAP_REGION0_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_4_RQOS_MAP_REGION0_SHIFT 16 -#define DDRC_PCFGQOS0_4_RQOS_MAP_REGION0_MASK 0x00030000U - -/*Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values.*/ -#undef DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1_DEFVAL -#undef DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1_SHIFT -#undef DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1_MASK -#define DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1_SHIFT 0 -#define DDRC_PCFGQOS0_4_RQOS_MAP_LEVEL1_MASK 0x0000000FU - -/*Specifies the timeout value for transactions mapped to the red address queue.*/ -#undef DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR_DEFVAL -#undef DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR_SHIFT -#undef DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR_MASK -#define DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR_SHIFT 16 -#define DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTR_MASK 0x07FF0000U - -/*Specifies the timeout value for transactions mapped to the blue address queue.*/ -#undef DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB_DEFVAL -#undef DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB_SHIFT -#undef DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB_MASK -#define DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB_SHIFT 0 -#define DDRC_PCFGQOS1_4_RQOS_MAP_TIMEOUTB_MASK 0x000007FFU - -/*This bitfield indicates the traffic class of region 1. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW traffic.*/ -#undef DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1_DEFVAL -#undef DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1_SHIFT -#undef DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1_MASK -#define DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1_DEFVAL 0x00000000 -#define DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1_SHIFT 20 -#define DDRC_PCFGWQOS0_4_WQOS_MAP_REGION1_MASK 0x00300000U - -/*This bitfield indicates the traffic class of region 0. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW traffic.*/ -#undef DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0_DEFVAL -#undef DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0_SHIFT -#undef DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0_MASK -#define DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0_DEFVAL 0x00000000 -#define DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0_SHIFT 16 -#define DDRC_PCFGWQOS0_4_WQOS_MAP_REGION0_MASK 0x00030000U - -/*Separation level indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 14 which c - rresponds to awqos. Note that for PA, awqos values are used directly as port priorities, where the higher the value correspon - s to higher port priority.*/ -#undef DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL_DEFVAL -#undef DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL_SHIFT -#undef DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL_MASK -#define DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL_DEFVAL 0x00000000 -#define DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL_SHIFT 0 -#define DDRC_PCFGWQOS0_4_WQOS_MAP_LEVEL_MASK 0x0000000FU - -/*Specifies the timeout value for write transactions.*/ -#undef DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT_DEFVAL -#undef DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT_SHIFT -#undef DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT_MASK -#define DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT_DEFVAL -#define DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT_SHIFT 0 -#define DDRC_PCFGWQOS1_4_WQOS_MAP_TIMEOUT_MASK 0x000007FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGR_5_RD_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (arurgent). When enabled and arurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_lpr/co_gs_go2critical_hpr signal to DDRC is asserted if enabled in PCCFG. - o2critical_en register. Note that arurgent signal can be asserted anytime and as long as required which is independent of add - ess handshaking (it is not associated with any particular command).*/ -#undef DDRC_PCFGR_5_RD_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGR_5_RD_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGR_5_RD_PORT_URGENT_EN_MASK -#define DDRC_PCFGR_5_RD_PORT_URGENT_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_5_RD_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGR_5_RD_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the read channel of the port.*/ -#undef DDRC_PCFGR_5_RD_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGR_5_RD_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGR_5_RD_PORT_AGING_EN_MASK -#define DDRC_PCFGR_5_RD_PORT_AGING_EN_DEFVAL 0x00000000 -#define DDRC_PCFGR_5_RD_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGR_5_RD_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of read aging counters. These counters will be parallel loaded after reset, or after each g - ant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - he higher significant 5-bits of the read aging counter sets the priority of the read channel of a given port. Port's priority - will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0, the corre - ponding port channel will have the highest priority level (timeout condition - Priority0). For multi-port configurations, the - aging counters cannot be used to set port priorities when external dynamic priority inputs (arqos) are enabled (timeout is st - ll applicable). For single port configurations, the aging counters are only used when they timeout (become 0) to force read-w - ite direction switching. In this case, external dynamic priority input, arqos (for reads only) can still be used to set the D - RC read priority (2 priority levels: low priority read - LPR, high priority read - HPR) on a command by command basis. Note: - he two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGR_5_RD_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGR_5_RD_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGR_5_RD_PORT_PRIORITY_MASK -#define DDRC_PCFGR_5_RD_PORT_PRIORITY_DEFVAL 0x00000000 -#define DDRC_PCFGR_5_RD_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGR_5_RD_PORT_PRIORITY_MASK 0x000003FFU - -/*If set to 1, enables the Page Match feature. If enabled, once a requesting port is granted, the port is continued to be grant - d if the following immediate commands are to the same memory page (same bank and same row). See also related PCCFG.pagematch_ - imit register.*/ -#undef DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN_DEFVAL -#undef DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN_SHIFT -#undef DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN_MASK -#define DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN_SHIFT 14 -#define DDRC_PCFGW_5_WR_PORT_PAGEMATCH_EN_MASK 0x00004000U - -/*If set to 1, enables the AXI urgent sideband signal (awurgent). When enabled and awurgent is asserted by the master, that por - becomes the highest priority and co_gs_go2critical_wr signal to DDRC is asserted if enabled in PCCFG.go2critical_en register - Note that awurgent signal can be asserted anytime and as long as required which is independent of address handshaking (it is - not associated with any particular command).*/ -#undef DDRC_PCFGW_5_WR_PORT_URGENT_EN_DEFVAL -#undef DDRC_PCFGW_5_WR_PORT_URGENT_EN_SHIFT -#undef DDRC_PCFGW_5_WR_PORT_URGENT_EN_MASK -#define DDRC_PCFGW_5_WR_PORT_URGENT_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_5_WR_PORT_URGENT_EN_SHIFT 13 -#define DDRC_PCFGW_5_WR_PORT_URGENT_EN_MASK 0x00002000U - -/*If set to 1, enables aging function for the write channel of the port.*/ -#undef DDRC_PCFGW_5_WR_PORT_AGING_EN_DEFVAL -#undef DDRC_PCFGW_5_WR_PORT_AGING_EN_SHIFT -#undef DDRC_PCFGW_5_WR_PORT_AGING_EN_MASK -#define DDRC_PCFGW_5_WR_PORT_AGING_EN_DEFVAL 0x00004000 -#define DDRC_PCFGW_5_WR_PORT_AGING_EN_SHIFT 12 -#define DDRC_PCFGW_5_WR_PORT_AGING_EN_MASK 0x00001000U - -/*Determines the initial load value of write aging counters. These counters will be parallel loaded after reset, or after each - rant to the corresponding port. The aging counters down-count every clock cycle where the port is requesting but not granted. - The higher significant 5-bits of the write aging counter sets the initial priority of the write channel of a given port. Port - s priority will increase as the higher significant 5-bits of the counter starts to decrease. When the aging counter becomes 0 - the corresponding port channel will have the highest priority level. For multi-port configurations, the aging counters canno - be used to set port priorities when external dynamic priority inputs (awqos) are enabled (timeout is still applicable). For - ingle port configurations, the aging counters are only used when they timeout (become 0) to force read-write direction switch - ng. Note: The two LSBs of this register field are tied internally to 2'b00.*/ -#undef DDRC_PCFGW_5_WR_PORT_PRIORITY_DEFVAL -#undef DDRC_PCFGW_5_WR_PORT_PRIORITY_SHIFT -#undef DDRC_PCFGW_5_WR_PORT_PRIORITY_MASK -#define DDRC_PCFGW_5_WR_PORT_PRIORITY_DEFVAL 0x00004000 -#define DDRC_PCFGW_5_WR_PORT_PRIORITY_SHIFT 0 -#define DDRC_PCFGW_5_WR_PORT_PRIORITY_MASK 0x000003FFU - -/*Enables port n.*/ -#undef DDRC_PCTRL_5_PORT_EN_DEFVAL -#undef DDRC_PCTRL_5_PORT_EN_SHIFT -#undef DDRC_PCTRL_5_PORT_EN_MASK -#define DDRC_PCTRL_5_PORT_EN_DEFVAL -#define DDRC_PCTRL_5_PORT_EN_SHIFT 0 -#define DDRC_PCTRL_5_PORT_EN_MASK 0x00000001U - -/*This bitfield indicates the traffic class of region 1. Valid values are: 0 : LPR, 1: VPR, 2: HPR. For dual address queue conf - gurations, region1 maps to the blue address queue. In this case, valid values are 0: LPR and 1: VPR only. When VPR support is - disabled (UMCTL2_VPR_EN = 0) and traffic class of region 1 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_5_RQOS_MAP_REGION1_DEFVAL -#undef DDRC_PCFGQOS0_5_RQOS_MAP_REGION1_SHIFT -#undef DDRC_PCFGQOS0_5_RQOS_MAP_REGION1_MASK -#define DDRC_PCFGQOS0_5_RQOS_MAP_REGION1_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_5_RQOS_MAP_REGION1_SHIFT 20 -#define DDRC_PCFGQOS0_5_RQOS_MAP_REGION1_MASK 0x00300000U - -/*This bitfield indicates the traffic class of region 0. Valid values are: 0: LPR, 1: VPR, 2: HPR. For dual address queue confi - urations, region 0 maps to the blue address queue. In this case, valid values are: 0: LPR and 1: VPR only. When VPR support i - disabled (UMCTL2_VPR_EN = 0) and traffic class of region0 is set to 1 (VPR), VPR traffic is aliased to LPR traffic.*/ -#undef DDRC_PCFGQOS0_5_RQOS_MAP_REGION0_DEFVAL -#undef DDRC_PCFGQOS0_5_RQOS_MAP_REGION0_SHIFT -#undef DDRC_PCFGQOS0_5_RQOS_MAP_REGION0_MASK -#define DDRC_PCFGQOS0_5_RQOS_MAP_REGION0_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_5_RQOS_MAP_REGION0_SHIFT 16 -#define DDRC_PCFGQOS0_5_RQOS_MAP_REGION0_MASK 0x00030000U - -/*Separation level1 indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 13 (for d - al RAQ) or 0 to 14 (for single RAQ) which corresponds to arqos. Note that for PA, arqos values are used directly as port prio - ities, where the higher the value corresponds to higher port priority. All of the map_level* registers must be set to distinc - values.*/ -#undef DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1_DEFVAL -#undef DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1_SHIFT -#undef DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1_MASK -#define DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1_DEFVAL 0x00000000 -#define DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1_SHIFT 0 -#define DDRC_PCFGQOS0_5_RQOS_MAP_LEVEL1_MASK 0x0000000FU - -/*Specifies the timeout value for transactions mapped to the red address queue.*/ -#undef DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR_DEFVAL -#undef DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR_SHIFT -#undef DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR_MASK -#define DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR_SHIFT 16 -#define DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTR_MASK 0x07FF0000U - -/*Specifies the timeout value for transactions mapped to the blue address queue.*/ -#undef DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB_DEFVAL -#undef DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB_SHIFT -#undef DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB_MASK -#define DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB_DEFVAL 0x00000000 -#define DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB_SHIFT 0 -#define DDRC_PCFGQOS1_5_RQOS_MAP_TIMEOUTB_MASK 0x000007FFU - -/*This bitfield indicates the traffic class of region 1. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region 1 is set to 1 (VPW), VPW traffic is aliased to LPW traffic.*/ -#undef DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1_DEFVAL -#undef DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1_SHIFT -#undef DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1_MASK -#define DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1_DEFVAL 0x00000000 -#define DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1_SHIFT 20 -#define DDRC_PCFGWQOS0_5_WQOS_MAP_REGION1_MASK 0x00300000U - -/*This bitfield indicates the traffic class of region 0. Valid values are: 0: NPW, 1: VPW. When VPW support is disabled (UMCTL2 - VPW_EN = 0) and traffic class of region0 is set to 1 (VPW), VPW traffic is aliased to NPW traffic.*/ -#undef DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0_DEFVAL -#undef DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0_SHIFT -#undef DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0_MASK -#define DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0_DEFVAL 0x00000000 -#define DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0_SHIFT 16 -#define DDRC_PCFGWQOS0_5_WQOS_MAP_REGION0_MASK 0x00030000U - -/*Separation level indicating the end of region0 mapping; start of region0 is 0. Possible values for level1 are 0 to 14 which c - rresponds to awqos. Note that for PA, awqos values are used directly as port priorities, where the higher the value correspon - s to higher port priority.*/ -#undef DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL_DEFVAL -#undef DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL_SHIFT -#undef DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL_MASK -#define DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL_DEFVAL 0x00000000 -#define DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL_SHIFT 0 -#define DDRC_PCFGWQOS0_5_WQOS_MAP_LEVEL_MASK 0x0000000FU - -/*Specifies the timeout value for write transactions.*/ -#undef DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT_DEFVAL -#undef DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT_SHIFT -#undef DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT_MASK -#define DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT_DEFVAL -#define DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT_SHIFT 0 -#define DDRC_PCFGWQOS1_5_WQOS_MAP_TIMEOUT_MASK 0x000007FFU - -/*Base address for address region n specified as awaddr[UMCTL2_A_ADDRW-1:x] and araddr[UMCTL2_A_ADDRW-1:x] where x is determine - by the minimum block size parameter UMCTL2_SARMINSIZE: (x=log2(block size)).*/ -#undef DDRC_SARBASE0_BASE_ADDR_DEFVAL -#undef DDRC_SARBASE0_BASE_ADDR_SHIFT -#undef DDRC_SARBASE0_BASE_ADDR_MASK -#define DDRC_SARBASE0_BASE_ADDR_DEFVAL -#define DDRC_SARBASE0_BASE_ADDR_SHIFT 0 -#define DDRC_SARBASE0_BASE_ADDR_MASK 0x000001FFU - -/*Number of blocks for address region n. This register determines the total size of the region in multiples of minimum block si - e as specified by the hardware parameter UMCTL2_SARMINSIZE. The register value is encoded as number of blocks = nblocks + 1. - or example, if register is programmed to 0, region will have 1 block.*/ -#undef DDRC_SARSIZE0_NBLOCKS_DEFVAL -#undef DDRC_SARSIZE0_NBLOCKS_SHIFT -#undef DDRC_SARSIZE0_NBLOCKS_MASK -#define DDRC_SARSIZE0_NBLOCKS_DEFVAL -#define DDRC_SARSIZE0_NBLOCKS_SHIFT 0 -#define DDRC_SARSIZE0_NBLOCKS_MASK 0x000000FFU - -/*Base address for address region n specified as awaddr[UMCTL2_A_ADDRW-1:x] and araddr[UMCTL2_A_ADDRW-1:x] where x is determine - by the minimum block size parameter UMCTL2_SARMINSIZE: (x=log2(block size)).*/ -#undef DDRC_SARBASE1_BASE_ADDR_DEFVAL -#undef DDRC_SARBASE1_BASE_ADDR_SHIFT -#undef DDRC_SARBASE1_BASE_ADDR_MASK -#define DDRC_SARBASE1_BASE_ADDR_DEFVAL -#define DDRC_SARBASE1_BASE_ADDR_SHIFT 0 -#define DDRC_SARBASE1_BASE_ADDR_MASK 0x000001FFU - -/*Number of blocks for address region n. This register determines the total size of the region in multiples of minimum block si - e as specified by the hardware parameter UMCTL2_SARMINSIZE. The register value is encoded as number of blocks = nblocks + 1. - or example, if register is programmed to 0, region will have 1 block.*/ -#undef DDRC_SARSIZE1_NBLOCKS_DEFVAL -#undef DDRC_SARSIZE1_NBLOCKS_SHIFT -#undef DDRC_SARSIZE1_NBLOCKS_MASK -#define DDRC_SARSIZE1_NBLOCKS_DEFVAL -#define DDRC_SARSIZE1_NBLOCKS_SHIFT 0 -#define DDRC_SARSIZE1_NBLOCKS_MASK 0x000000FFU - -/*Specifies the number of DFI clock cycles after an assertion or de-assertion of the DFI control signals that the control signa - s at the PHY-DRAM interface reflect the assertion or de-assertion. If the DFI clock and the memory clock are not phase-aligne - , this timing parameter should be rounded up to the next integer value. Note that if using RDIMM, it is necessary to incremen - this parameter by RDIMM's extra cycle of latency in terms of DFI clock.*/ -#undef DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY_DEFVAL -#undef DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY_SHIFT -#undef DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY_MASK -#define DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY_DEFVAL 0x07020002 -#define DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY_SHIFT 24 -#define DDRC_DFITMG0_SHADOW_DFI_T_CTRL_DELAY_MASK 0x1F000000U - -/*Defines whether dfi_rddata_en/dfi_rddata/dfi_rddata_valid is generated using HDR or SDR values Selects whether value in DFITM - 0.dfi_t_rddata_en is in terms of SDR or HDR clock cycles: - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles R - fer to PHY specification for correct value.*/ -#undef DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR_DEFVAL -#undef DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR_SHIFT -#undef DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR_MASK -#define DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR_DEFVAL 0x07020002 -#define DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR_SHIFT 23 -#define DDRC_DFITMG0_SHADOW_DFI_RDDATA_USE_SDR_MASK 0x00800000U - -/*Time from the assertion of a read command on the DFI interface to the assertion of the dfi_rddata_en signal. Refer to PHY spe - ification for correct value. This corresponds to the DFI parameter trddata_en. Note that, depending on the PHY, if using RDIM - , it may be necessary to use the value (CL + 1) in the calculation of trddata_en. This is to compensate for the extra cycle o - latency through the RDIMM. Unit: Clocks*/ -#undef DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN_DEFVAL -#undef DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN_SHIFT -#undef DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN_MASK -#define DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN_DEFVAL 0x07020002 -#define DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN_SHIFT 16 -#define DDRC_DFITMG0_SHADOW_DFI_T_RDDATA_EN_MASK 0x003F0000U - -/*Defines whether dfi_wrdata_en/dfi_wrdata/dfi_wrdata_mask is generated using HDR or SDR values Selects whether value in DFITMG - .dfi_tphy_wrlat is in terms of SDR or HDR clock cycles Selects whether value in DFITMG0.dfi_tphy_wrdata is in terms of SDR or - HDR clock cycles - 0 in terms of HDR clock cycles - 1 in terms of SDR clock cycles Refer to PHY specification for correct val - e.*/ -#undef DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR_DEFVAL -#undef DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR_SHIFT -#undef DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR_MASK -#define DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR_DEFVAL 0x07020002 -#define DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR_SHIFT 15 -#define DDRC_DFITMG0_SHADOW_DFI_WRDATA_USE_SDR_MASK 0x00008000U - -/*Specifies the number of clock cycles between when dfi_wrdata_en is asserted to when the associated write data is driven on th - dfi_wrdata signal. This corresponds to the DFI timing parameter tphy_wrdata. Refer to PHY specification for correct value. N - te, max supported value is 8. Unit: Clocks*/ -#undef DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA_DEFVAL -#undef DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA_SHIFT -#undef DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA_MASK -#define DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA_DEFVAL 0x07020002 -#define DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA_SHIFT 8 -#define DDRC_DFITMG0_SHADOW_DFI_TPHY_WRDATA_MASK 0x00003F00U - -/*Write latency Number of clocks from the write command to write data enable (dfi_wrdata_en). This corresponds to the DFI timin - parameter tphy_wrlat. Refer to PHY specification for correct value.Note that, depending on the PHY, if using RDIMM, it may b - necessary to use the value (CL + 1) in the calculation of tphy_wrlat. This is to compensate for the extra cycle of latency t - rough the RDIMM.*/ -#undef DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT_DEFVAL -#undef DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT_SHIFT -#undef DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT_MASK -#define DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT_DEFVAL 0x07020002 -#define DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT_SHIFT 0 -#define DDRC_DFITMG0_SHADOW_DFI_TPHY_WRLAT_MASK 0x0000003FU - -/*DDR block level reset inside of the DDR Sub System*/ -#undef CRF_APB_RST_DDR_SS_DDR_RESET_DEFVAL -#undef CRF_APB_RST_DDR_SS_DDR_RESET_SHIFT -#undef CRF_APB_RST_DDR_SS_DDR_RESET_MASK -#define CRF_APB_RST_DDR_SS_DDR_RESET_DEFVAL 0x0000000F -#define CRF_APB_RST_DDR_SS_DDR_RESET_SHIFT 3 -#define CRF_APB_RST_DDR_SS_DDR_RESET_MASK 0x00000008U - -/*Address Copy*/ -#undef DDR_PHY_PGCR0_ADCP_DEFVAL -#undef DDR_PHY_PGCR0_ADCP_SHIFT -#undef DDR_PHY_PGCR0_ADCP_MASK -#define DDR_PHY_PGCR0_ADCP_DEFVAL 0x07001E00 -#define DDR_PHY_PGCR0_ADCP_SHIFT 31 -#define DDR_PHY_PGCR0_ADCP_MASK 0x80000000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_PGCR0_RESERVED_30_27_DEFVAL -#undef DDR_PHY_PGCR0_RESERVED_30_27_SHIFT -#undef DDR_PHY_PGCR0_RESERVED_30_27_MASK -#define DDR_PHY_PGCR0_RESERVED_30_27_DEFVAL 0x07001E00 -#define DDR_PHY_PGCR0_RESERVED_30_27_SHIFT 27 -#define DDR_PHY_PGCR0_RESERVED_30_27_MASK 0x78000000U - -/*PHY FIFO Reset*/ -#undef DDR_PHY_PGCR0_PHYFRST_DEFVAL -#undef DDR_PHY_PGCR0_PHYFRST_SHIFT -#undef DDR_PHY_PGCR0_PHYFRST_MASK -#define DDR_PHY_PGCR0_PHYFRST_DEFVAL 0x07001E00 -#define DDR_PHY_PGCR0_PHYFRST_SHIFT 26 -#define DDR_PHY_PGCR0_PHYFRST_MASK 0x04000000U - -/*Oscillator Mode Address/Command Delay Line Select*/ -#undef DDR_PHY_PGCR0_OSCACDL_DEFVAL -#undef DDR_PHY_PGCR0_OSCACDL_SHIFT -#undef DDR_PHY_PGCR0_OSCACDL_MASK -#define DDR_PHY_PGCR0_OSCACDL_DEFVAL 0x07001E00 -#define DDR_PHY_PGCR0_OSCACDL_SHIFT 24 -#define DDR_PHY_PGCR0_OSCACDL_MASK 0x03000000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_PGCR0_RESERVED_23_19_DEFVAL -#undef DDR_PHY_PGCR0_RESERVED_23_19_SHIFT -#undef DDR_PHY_PGCR0_RESERVED_23_19_MASK -#define DDR_PHY_PGCR0_RESERVED_23_19_DEFVAL 0x07001E00 -#define DDR_PHY_PGCR0_RESERVED_23_19_SHIFT 19 -#define DDR_PHY_PGCR0_RESERVED_23_19_MASK 0x00F80000U - -/*Digital Test Output Select*/ -#undef DDR_PHY_PGCR0_DTOSEL_DEFVAL -#undef DDR_PHY_PGCR0_DTOSEL_SHIFT -#undef DDR_PHY_PGCR0_DTOSEL_MASK -#define DDR_PHY_PGCR0_DTOSEL_DEFVAL 0x07001E00 -#define DDR_PHY_PGCR0_DTOSEL_SHIFT 14 -#define DDR_PHY_PGCR0_DTOSEL_MASK 0x0007C000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_PGCR0_RESERVED_13_DEFVAL -#undef DDR_PHY_PGCR0_RESERVED_13_SHIFT -#undef DDR_PHY_PGCR0_RESERVED_13_MASK -#define DDR_PHY_PGCR0_RESERVED_13_DEFVAL 0x07001E00 -#define DDR_PHY_PGCR0_RESERVED_13_SHIFT 13 -#define DDR_PHY_PGCR0_RESERVED_13_MASK 0x00002000U - -/*Oscillator Mode Division*/ -#undef DDR_PHY_PGCR0_OSCDIV_DEFVAL -#undef DDR_PHY_PGCR0_OSCDIV_SHIFT -#undef DDR_PHY_PGCR0_OSCDIV_MASK -#define DDR_PHY_PGCR0_OSCDIV_DEFVAL 0x07001E00 -#define DDR_PHY_PGCR0_OSCDIV_SHIFT 9 -#define DDR_PHY_PGCR0_OSCDIV_MASK 0x00001E00U - -/*Oscillator Enable*/ -#undef DDR_PHY_PGCR0_OSCEN_DEFVAL -#undef DDR_PHY_PGCR0_OSCEN_SHIFT -#undef DDR_PHY_PGCR0_OSCEN_MASK -#define DDR_PHY_PGCR0_OSCEN_DEFVAL 0x07001E00 -#define DDR_PHY_PGCR0_OSCEN_SHIFT 8 -#define DDR_PHY_PGCR0_OSCEN_MASK 0x00000100U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_PGCR0_RESERVED_7_0_DEFVAL -#undef DDR_PHY_PGCR0_RESERVED_7_0_SHIFT -#undef DDR_PHY_PGCR0_RESERVED_7_0_MASK -#define DDR_PHY_PGCR0_RESERVED_7_0_DEFVAL 0x07001E00 -#define DDR_PHY_PGCR0_RESERVED_7_0_SHIFT 0 -#define DDR_PHY_PGCR0_RESERVED_7_0_MASK 0x000000FFU - -/*Clear Training Status Registers*/ -#undef DDR_PHY_PGCR2_CLRTSTAT_DEFVAL -#undef DDR_PHY_PGCR2_CLRTSTAT_SHIFT -#undef DDR_PHY_PGCR2_CLRTSTAT_MASK -#define DDR_PHY_PGCR2_CLRTSTAT_DEFVAL 0x00F12480 -#define DDR_PHY_PGCR2_CLRTSTAT_SHIFT 31 -#define DDR_PHY_PGCR2_CLRTSTAT_MASK 0x80000000U - -/*Clear Impedance Calibration*/ -#undef DDR_PHY_PGCR2_CLRZCAL_DEFVAL -#undef DDR_PHY_PGCR2_CLRZCAL_SHIFT -#undef DDR_PHY_PGCR2_CLRZCAL_MASK -#define DDR_PHY_PGCR2_CLRZCAL_DEFVAL 0x00F12480 -#define DDR_PHY_PGCR2_CLRZCAL_SHIFT 30 -#define DDR_PHY_PGCR2_CLRZCAL_MASK 0x40000000U - -/*Clear Parity Error*/ -#undef DDR_PHY_PGCR2_CLRPERR_DEFVAL -#undef DDR_PHY_PGCR2_CLRPERR_SHIFT -#undef DDR_PHY_PGCR2_CLRPERR_MASK -#define DDR_PHY_PGCR2_CLRPERR_DEFVAL 0x00F12480 -#define DDR_PHY_PGCR2_CLRPERR_SHIFT 29 -#define DDR_PHY_PGCR2_CLRPERR_MASK 0x20000000U - -/*Initialization Complete Pin Configuration*/ -#undef DDR_PHY_PGCR2_ICPC_DEFVAL -#undef DDR_PHY_PGCR2_ICPC_SHIFT -#undef DDR_PHY_PGCR2_ICPC_MASK -#define DDR_PHY_PGCR2_ICPC_DEFVAL 0x00F12480 -#define DDR_PHY_PGCR2_ICPC_SHIFT 28 -#define DDR_PHY_PGCR2_ICPC_MASK 0x10000000U - -/*Data Training PUB Mode Exit Timer*/ -#undef DDR_PHY_PGCR2_DTPMXTMR_DEFVAL -#undef DDR_PHY_PGCR2_DTPMXTMR_SHIFT -#undef DDR_PHY_PGCR2_DTPMXTMR_MASK -#define DDR_PHY_PGCR2_DTPMXTMR_DEFVAL 0x00F12480 -#define DDR_PHY_PGCR2_DTPMXTMR_SHIFT 20 -#define DDR_PHY_PGCR2_DTPMXTMR_MASK 0x0FF00000U - -/*Initialization Bypass*/ -#undef DDR_PHY_PGCR2_INITFSMBYP_DEFVAL -#undef DDR_PHY_PGCR2_INITFSMBYP_SHIFT -#undef DDR_PHY_PGCR2_INITFSMBYP_MASK -#define DDR_PHY_PGCR2_INITFSMBYP_DEFVAL 0x00F12480 -#define DDR_PHY_PGCR2_INITFSMBYP_SHIFT 19 -#define DDR_PHY_PGCR2_INITFSMBYP_MASK 0x00080000U - -/*PLL FSM Bypass*/ -#undef DDR_PHY_PGCR2_PLLFSMBYP_DEFVAL -#undef DDR_PHY_PGCR2_PLLFSMBYP_SHIFT -#undef DDR_PHY_PGCR2_PLLFSMBYP_MASK -#define DDR_PHY_PGCR2_PLLFSMBYP_DEFVAL 0x00F12480 -#define DDR_PHY_PGCR2_PLLFSMBYP_SHIFT 18 -#define DDR_PHY_PGCR2_PLLFSMBYP_MASK 0x00040000U - -/*Refresh Period*/ -#undef DDR_PHY_PGCR2_TREFPRD_DEFVAL -#undef DDR_PHY_PGCR2_TREFPRD_SHIFT -#undef DDR_PHY_PGCR2_TREFPRD_MASK -#define DDR_PHY_PGCR2_TREFPRD_DEFVAL 0x00F12480 -#define DDR_PHY_PGCR2_TREFPRD_SHIFT 0 -#define DDR_PHY_PGCR2_TREFPRD_MASK 0x0003FFFFU - -/*CKN Enable*/ -#undef DDR_PHY_PGCR3_CKNEN_DEFVAL -#undef DDR_PHY_PGCR3_CKNEN_SHIFT -#undef DDR_PHY_PGCR3_CKNEN_MASK -#define DDR_PHY_PGCR3_CKNEN_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_CKNEN_SHIFT 24 -#define DDR_PHY_PGCR3_CKNEN_MASK 0xFF000000U - -/*CK Enable*/ -#undef DDR_PHY_PGCR3_CKEN_DEFVAL -#undef DDR_PHY_PGCR3_CKEN_SHIFT -#undef DDR_PHY_PGCR3_CKEN_MASK -#define DDR_PHY_PGCR3_CKEN_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_CKEN_SHIFT 16 -#define DDR_PHY_PGCR3_CKEN_MASK 0x00FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_PGCR3_RESERVED_15_DEFVAL -#undef DDR_PHY_PGCR3_RESERVED_15_SHIFT -#undef DDR_PHY_PGCR3_RESERVED_15_MASK -#define DDR_PHY_PGCR3_RESERVED_15_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_RESERVED_15_SHIFT 15 -#define DDR_PHY_PGCR3_RESERVED_15_MASK 0x00008000U - -/*Enable Clock Gating for AC [0] ctl_rd_clk*/ -#undef DDR_PHY_PGCR3_GATEACRDCLK_DEFVAL -#undef DDR_PHY_PGCR3_GATEACRDCLK_SHIFT -#undef DDR_PHY_PGCR3_GATEACRDCLK_MASK -#define DDR_PHY_PGCR3_GATEACRDCLK_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_GATEACRDCLK_SHIFT 13 -#define DDR_PHY_PGCR3_GATEACRDCLK_MASK 0x00006000U - -/*Enable Clock Gating for AC [0] ddr_clk*/ -#undef DDR_PHY_PGCR3_GATEACDDRCLK_DEFVAL -#undef DDR_PHY_PGCR3_GATEACDDRCLK_SHIFT -#undef DDR_PHY_PGCR3_GATEACDDRCLK_MASK -#define DDR_PHY_PGCR3_GATEACDDRCLK_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_GATEACDDRCLK_SHIFT 11 -#define DDR_PHY_PGCR3_GATEACDDRCLK_MASK 0x00001800U - -/*Enable Clock Gating for AC [0] ctl_clk*/ -#undef DDR_PHY_PGCR3_GATEACCTLCLK_DEFVAL -#undef DDR_PHY_PGCR3_GATEACCTLCLK_SHIFT -#undef DDR_PHY_PGCR3_GATEACCTLCLK_MASK -#define DDR_PHY_PGCR3_GATEACCTLCLK_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_GATEACCTLCLK_SHIFT 9 -#define DDR_PHY_PGCR3_GATEACCTLCLK_MASK 0x00000600U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_PGCR3_RESERVED_8_DEFVAL -#undef DDR_PHY_PGCR3_RESERVED_8_SHIFT -#undef DDR_PHY_PGCR3_RESERVED_8_MASK -#define DDR_PHY_PGCR3_RESERVED_8_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_RESERVED_8_SHIFT 8 -#define DDR_PHY_PGCR3_RESERVED_8_MASK 0x00000100U - -/*Controls DDL Bypass Modes*/ -#undef DDR_PHY_PGCR3_DDLBYPMODE_DEFVAL -#undef DDR_PHY_PGCR3_DDLBYPMODE_SHIFT -#undef DDR_PHY_PGCR3_DDLBYPMODE_MASK -#define DDR_PHY_PGCR3_DDLBYPMODE_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_DDLBYPMODE_SHIFT 6 -#define DDR_PHY_PGCR3_DDLBYPMODE_MASK 0x000000C0U - -/*IO Loop-Back Select*/ -#undef DDR_PHY_PGCR3_IOLB_DEFVAL -#undef DDR_PHY_PGCR3_IOLB_SHIFT -#undef DDR_PHY_PGCR3_IOLB_MASK -#define DDR_PHY_PGCR3_IOLB_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_IOLB_SHIFT 5 -#define DDR_PHY_PGCR3_IOLB_MASK 0x00000020U - -/*AC Receive FIFO Read Mode*/ -#undef DDR_PHY_PGCR3_RDMODE_DEFVAL -#undef DDR_PHY_PGCR3_RDMODE_SHIFT -#undef DDR_PHY_PGCR3_RDMODE_MASK -#define DDR_PHY_PGCR3_RDMODE_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_RDMODE_SHIFT 3 -#define DDR_PHY_PGCR3_RDMODE_MASK 0x00000018U - -/*Read FIFO Reset Disable*/ -#undef DDR_PHY_PGCR3_DISRST_DEFVAL -#undef DDR_PHY_PGCR3_DISRST_SHIFT -#undef DDR_PHY_PGCR3_DISRST_MASK -#define DDR_PHY_PGCR3_DISRST_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_DISRST_SHIFT 2 -#define DDR_PHY_PGCR3_DISRST_MASK 0x00000004U - -/*Clock Level when Clock Gating*/ -#undef DDR_PHY_PGCR3_CLKLEVEL_DEFVAL -#undef DDR_PHY_PGCR3_CLKLEVEL_SHIFT -#undef DDR_PHY_PGCR3_CLKLEVEL_MASK -#define DDR_PHY_PGCR3_CLKLEVEL_DEFVAL 0x55AA0080 -#define DDR_PHY_PGCR3_CLKLEVEL_SHIFT 0 -#define DDR_PHY_PGCR3_CLKLEVEL_MASK 0x00000003U - -/*Frequency B Ratio Term*/ -#undef DDR_PHY_PGCR5_FRQBT_DEFVAL -#undef DDR_PHY_PGCR5_FRQBT_SHIFT -#undef DDR_PHY_PGCR5_FRQBT_MASK -#define DDR_PHY_PGCR5_FRQBT_DEFVAL 0x01010000 -#define DDR_PHY_PGCR5_FRQBT_SHIFT 24 -#define DDR_PHY_PGCR5_FRQBT_MASK 0xFF000000U - -/*Frequency A Ratio Term*/ -#undef DDR_PHY_PGCR5_FRQAT_DEFVAL -#undef DDR_PHY_PGCR5_FRQAT_SHIFT -#undef DDR_PHY_PGCR5_FRQAT_MASK -#define DDR_PHY_PGCR5_FRQAT_DEFVAL 0x01010000 -#define DDR_PHY_PGCR5_FRQAT_SHIFT 16 -#define DDR_PHY_PGCR5_FRQAT_MASK 0x00FF0000U - -/*DFI Disconnect Time Period*/ -#undef DDR_PHY_PGCR5_DISCNPERIOD_DEFVAL -#undef DDR_PHY_PGCR5_DISCNPERIOD_SHIFT -#undef DDR_PHY_PGCR5_DISCNPERIOD_MASK -#define DDR_PHY_PGCR5_DISCNPERIOD_DEFVAL 0x01010000 -#define DDR_PHY_PGCR5_DISCNPERIOD_SHIFT 8 -#define DDR_PHY_PGCR5_DISCNPERIOD_MASK 0x0000FF00U - -/*Receiver bias core side control*/ -#undef DDR_PHY_PGCR5_VREF_RBCTRL_DEFVAL -#undef DDR_PHY_PGCR5_VREF_RBCTRL_SHIFT -#undef DDR_PHY_PGCR5_VREF_RBCTRL_MASK -#define DDR_PHY_PGCR5_VREF_RBCTRL_DEFVAL 0x01010000 -#define DDR_PHY_PGCR5_VREF_RBCTRL_SHIFT 4 -#define DDR_PHY_PGCR5_VREF_RBCTRL_MASK 0x000000F0U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_PGCR5_RESERVED_3_DEFVAL -#undef DDR_PHY_PGCR5_RESERVED_3_SHIFT -#undef DDR_PHY_PGCR5_RESERVED_3_MASK -#define DDR_PHY_PGCR5_RESERVED_3_DEFVAL 0x01010000 -#define DDR_PHY_PGCR5_RESERVED_3_SHIFT 3 -#define DDR_PHY_PGCR5_RESERVED_3_MASK 0x00000008U - -/*Internal VREF generator REFSEL ragne select*/ -#undef DDR_PHY_PGCR5_DXREFISELRANGE_DEFVAL -#undef DDR_PHY_PGCR5_DXREFISELRANGE_SHIFT -#undef DDR_PHY_PGCR5_DXREFISELRANGE_MASK -#define DDR_PHY_PGCR5_DXREFISELRANGE_DEFVAL 0x01010000 -#define DDR_PHY_PGCR5_DXREFISELRANGE_SHIFT 2 -#define DDR_PHY_PGCR5_DXREFISELRANGE_MASK 0x00000004U - -/*DDL Page Read Write select*/ -#undef DDR_PHY_PGCR5_DDLPGACT_DEFVAL -#undef DDR_PHY_PGCR5_DDLPGACT_SHIFT -#undef DDR_PHY_PGCR5_DDLPGACT_MASK -#define DDR_PHY_PGCR5_DDLPGACT_DEFVAL 0x01010000 -#define DDR_PHY_PGCR5_DDLPGACT_SHIFT 1 -#define DDR_PHY_PGCR5_DDLPGACT_MASK 0x00000002U - -/*DDL Page Read Write select*/ -#undef DDR_PHY_PGCR5_DDLPGRW_DEFVAL -#undef DDR_PHY_PGCR5_DDLPGRW_SHIFT -#undef DDR_PHY_PGCR5_DDLPGRW_MASK -#define DDR_PHY_PGCR5_DDLPGRW_DEFVAL 0x01010000 -#define DDR_PHY_PGCR5_DDLPGRW_SHIFT 0 -#define DDR_PHY_PGCR5_DDLPGRW_MASK 0x00000001U - -/*PLL Power-Down Time*/ -#undef DDR_PHY_PTR0_TPLLPD_DEFVAL -#undef DDR_PHY_PTR0_TPLLPD_SHIFT -#undef DDR_PHY_PTR0_TPLLPD_MASK -#define DDR_PHY_PTR0_TPLLPD_DEFVAL 0x42C21590 -#define DDR_PHY_PTR0_TPLLPD_SHIFT 21 -#define DDR_PHY_PTR0_TPLLPD_MASK 0xFFE00000U - -/*PLL Gear Shift Time*/ -#undef DDR_PHY_PTR0_TPLLGS_DEFVAL -#undef DDR_PHY_PTR0_TPLLGS_SHIFT -#undef DDR_PHY_PTR0_TPLLGS_MASK -#define DDR_PHY_PTR0_TPLLGS_DEFVAL 0x42C21590 -#define DDR_PHY_PTR0_TPLLGS_SHIFT 6 -#define DDR_PHY_PTR0_TPLLGS_MASK 0x001FFFC0U - -/*PHY Reset Time*/ -#undef DDR_PHY_PTR0_TPHYRST_DEFVAL -#undef DDR_PHY_PTR0_TPHYRST_SHIFT -#undef DDR_PHY_PTR0_TPHYRST_MASK -#define DDR_PHY_PTR0_TPHYRST_DEFVAL 0x42C21590 -#define DDR_PHY_PTR0_TPHYRST_SHIFT 0 -#define DDR_PHY_PTR0_TPHYRST_MASK 0x0000003FU - -/*PLL Lock Time*/ -#undef DDR_PHY_PTR1_TPLLLOCK_DEFVAL -#undef DDR_PHY_PTR1_TPLLLOCK_SHIFT -#undef DDR_PHY_PTR1_TPLLLOCK_MASK -#define DDR_PHY_PTR1_TPLLLOCK_DEFVAL 0xD05612C0 -#define DDR_PHY_PTR1_TPLLLOCK_SHIFT 16 -#define DDR_PHY_PTR1_TPLLLOCK_MASK 0xFFFF0000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_PTR1_RESERVED_15_13_DEFVAL -#undef DDR_PHY_PTR1_RESERVED_15_13_SHIFT -#undef DDR_PHY_PTR1_RESERVED_15_13_MASK -#define DDR_PHY_PTR1_RESERVED_15_13_DEFVAL 0xD05612C0 -#define DDR_PHY_PTR1_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_PTR1_RESERVED_15_13_MASK 0x0000E000U - -/*PLL Reset Time*/ -#undef DDR_PHY_PTR1_TPLLRST_DEFVAL -#undef DDR_PHY_PTR1_TPLLRST_SHIFT -#undef DDR_PHY_PTR1_TPLLRST_MASK -#define DDR_PHY_PTR1_TPLLRST_DEFVAL 0xD05612C0 -#define DDR_PHY_PTR1_TPLLRST_SHIFT 0 -#define DDR_PHY_PTR1_TPLLRST_MASK 0x00001FFFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DSGCR_RESERVED_31_28_DEFVAL -#undef DDR_PHY_DSGCR_RESERVED_31_28_SHIFT -#undef DDR_PHY_DSGCR_RESERVED_31_28_MASK -#define DDR_PHY_DSGCR_RESERVED_31_28_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_RESERVED_31_28_SHIFT 28 -#define DDR_PHY_DSGCR_RESERVED_31_28_MASK 0xF0000000U - -/*When RDBI enabled, this bit is used to select RDBI CL calculation, if it is 1b1, calculation will use RDBICL, otherwise use d - fault calculation.*/ -#undef DDR_PHY_DSGCR_RDBICLSEL_DEFVAL -#undef DDR_PHY_DSGCR_RDBICLSEL_SHIFT -#undef DDR_PHY_DSGCR_RDBICLSEL_MASK -#define DDR_PHY_DSGCR_RDBICLSEL_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_RDBICLSEL_SHIFT 27 -#define DDR_PHY_DSGCR_RDBICLSEL_MASK 0x08000000U - -/*When RDBI enabled, if RDBICLSEL is asserted, RDBI CL adjust using this value.*/ -#undef DDR_PHY_DSGCR_RDBICL_DEFVAL -#undef DDR_PHY_DSGCR_RDBICL_SHIFT -#undef DDR_PHY_DSGCR_RDBICL_MASK -#define DDR_PHY_DSGCR_RDBICL_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_RDBICL_SHIFT 24 -#define DDR_PHY_DSGCR_RDBICL_MASK 0x07000000U - -/*PHY Impedance Update Enable*/ -#undef DDR_PHY_DSGCR_PHYZUEN_DEFVAL -#undef DDR_PHY_DSGCR_PHYZUEN_SHIFT -#undef DDR_PHY_DSGCR_PHYZUEN_MASK -#define DDR_PHY_DSGCR_PHYZUEN_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_PHYZUEN_SHIFT 23 -#define DDR_PHY_DSGCR_PHYZUEN_MASK 0x00800000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DSGCR_RESERVED_22_DEFVAL -#undef DDR_PHY_DSGCR_RESERVED_22_SHIFT -#undef DDR_PHY_DSGCR_RESERVED_22_MASK -#define DDR_PHY_DSGCR_RESERVED_22_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_RESERVED_22_SHIFT 22 -#define DDR_PHY_DSGCR_RESERVED_22_MASK 0x00400000U - -/*SDRAM Reset Output Enable*/ -#undef DDR_PHY_DSGCR_RSTOE_DEFVAL -#undef DDR_PHY_DSGCR_RSTOE_SHIFT -#undef DDR_PHY_DSGCR_RSTOE_MASK -#define DDR_PHY_DSGCR_RSTOE_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_RSTOE_SHIFT 21 -#define DDR_PHY_DSGCR_RSTOE_MASK 0x00200000U - -/*Single Data Rate Mode*/ -#undef DDR_PHY_DSGCR_SDRMODE_DEFVAL -#undef DDR_PHY_DSGCR_SDRMODE_SHIFT -#undef DDR_PHY_DSGCR_SDRMODE_MASK -#define DDR_PHY_DSGCR_SDRMODE_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_SDRMODE_SHIFT 19 -#define DDR_PHY_DSGCR_SDRMODE_MASK 0x00180000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DSGCR_RESERVED_18_DEFVAL -#undef DDR_PHY_DSGCR_RESERVED_18_SHIFT -#undef DDR_PHY_DSGCR_RESERVED_18_MASK -#define DDR_PHY_DSGCR_RESERVED_18_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_RESERVED_18_SHIFT 18 -#define DDR_PHY_DSGCR_RESERVED_18_MASK 0x00040000U - -/*ATO Analog Test Enable*/ -#undef DDR_PHY_DSGCR_ATOAE_DEFVAL -#undef DDR_PHY_DSGCR_ATOAE_SHIFT -#undef DDR_PHY_DSGCR_ATOAE_MASK -#define DDR_PHY_DSGCR_ATOAE_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_ATOAE_SHIFT 17 -#define DDR_PHY_DSGCR_ATOAE_MASK 0x00020000U - -/*DTO Output Enable*/ -#undef DDR_PHY_DSGCR_DTOOE_DEFVAL -#undef DDR_PHY_DSGCR_DTOOE_SHIFT -#undef DDR_PHY_DSGCR_DTOOE_MASK -#define DDR_PHY_DSGCR_DTOOE_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_DTOOE_SHIFT 16 -#define DDR_PHY_DSGCR_DTOOE_MASK 0x00010000U - -/*DTO I/O Mode*/ -#undef DDR_PHY_DSGCR_DTOIOM_DEFVAL -#undef DDR_PHY_DSGCR_DTOIOM_SHIFT -#undef DDR_PHY_DSGCR_DTOIOM_MASK -#define DDR_PHY_DSGCR_DTOIOM_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_DTOIOM_SHIFT 15 -#define DDR_PHY_DSGCR_DTOIOM_MASK 0x00008000U - -/*DTO Power Down Receiver*/ -#undef DDR_PHY_DSGCR_DTOPDR_DEFVAL -#undef DDR_PHY_DSGCR_DTOPDR_SHIFT -#undef DDR_PHY_DSGCR_DTOPDR_MASK -#define DDR_PHY_DSGCR_DTOPDR_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_DTOPDR_SHIFT 14 -#define DDR_PHY_DSGCR_DTOPDR_MASK 0x00004000U - -/*Reserved. Return zeroes on reads*/ -#undef DDR_PHY_DSGCR_RESERVED_13_DEFVAL -#undef DDR_PHY_DSGCR_RESERVED_13_SHIFT -#undef DDR_PHY_DSGCR_RESERVED_13_MASK -#define DDR_PHY_DSGCR_RESERVED_13_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_RESERVED_13_SHIFT 13 -#define DDR_PHY_DSGCR_RESERVED_13_MASK 0x00002000U - -/*DTO On-Die Termination*/ -#undef DDR_PHY_DSGCR_DTOODT_DEFVAL -#undef DDR_PHY_DSGCR_DTOODT_SHIFT -#undef DDR_PHY_DSGCR_DTOODT_MASK -#define DDR_PHY_DSGCR_DTOODT_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_DTOODT_SHIFT 12 -#define DDR_PHY_DSGCR_DTOODT_MASK 0x00001000U - -/*PHY Update Acknowledge Delay*/ -#undef DDR_PHY_DSGCR_PUAD_DEFVAL -#undef DDR_PHY_DSGCR_PUAD_SHIFT -#undef DDR_PHY_DSGCR_PUAD_MASK -#define DDR_PHY_DSGCR_PUAD_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_PUAD_SHIFT 6 -#define DDR_PHY_DSGCR_PUAD_MASK 0x00000FC0U - -/*Controller Update Acknowledge Enable*/ -#undef DDR_PHY_DSGCR_CUAEN_DEFVAL -#undef DDR_PHY_DSGCR_CUAEN_SHIFT -#undef DDR_PHY_DSGCR_CUAEN_MASK -#define DDR_PHY_DSGCR_CUAEN_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_CUAEN_SHIFT 5 -#define DDR_PHY_DSGCR_CUAEN_MASK 0x00000020U - -/*Reserved. Return zeroes on reads*/ -#undef DDR_PHY_DSGCR_RESERVED_4_3_DEFVAL -#undef DDR_PHY_DSGCR_RESERVED_4_3_SHIFT -#undef DDR_PHY_DSGCR_RESERVED_4_3_MASK -#define DDR_PHY_DSGCR_RESERVED_4_3_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_RESERVED_4_3_SHIFT 3 -#define DDR_PHY_DSGCR_RESERVED_4_3_MASK 0x00000018U - -/*Controller Impedance Update Enable*/ -#undef DDR_PHY_DSGCR_CTLZUEN_DEFVAL -#undef DDR_PHY_DSGCR_CTLZUEN_SHIFT -#undef DDR_PHY_DSGCR_CTLZUEN_MASK -#define DDR_PHY_DSGCR_CTLZUEN_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_CTLZUEN_SHIFT 2 -#define DDR_PHY_DSGCR_CTLZUEN_MASK 0x00000004U - -/*Reserved. Return zeroes on reads*/ -#undef DDR_PHY_DSGCR_RESERVED_1_DEFVAL -#undef DDR_PHY_DSGCR_RESERVED_1_SHIFT -#undef DDR_PHY_DSGCR_RESERVED_1_MASK -#define DDR_PHY_DSGCR_RESERVED_1_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_RESERVED_1_SHIFT 1 -#define DDR_PHY_DSGCR_RESERVED_1_MASK 0x00000002U - -/*PHY Update Request Enable*/ -#undef DDR_PHY_DSGCR_PUREN_DEFVAL -#undef DDR_PHY_DSGCR_PUREN_SHIFT -#undef DDR_PHY_DSGCR_PUREN_MASK -#define DDR_PHY_DSGCR_PUREN_DEFVAL 0x02A04101 -#define DDR_PHY_DSGCR_PUREN_SHIFT 0 -#define DDR_PHY_DSGCR_PUREN_MASK 0x00000001U - -/*DDR4 Gear Down Timing.*/ -#undef DDR_PHY_DCR_GEARDN_DEFVAL -#undef DDR_PHY_DCR_GEARDN_SHIFT -#undef DDR_PHY_DCR_GEARDN_MASK -#define DDR_PHY_DCR_GEARDN_DEFVAL 0x0000040D -#define DDR_PHY_DCR_GEARDN_SHIFT 31 -#define DDR_PHY_DCR_GEARDN_MASK 0x80000000U - -/*Un-used Bank Group*/ -#undef DDR_PHY_DCR_UBG_DEFVAL -#undef DDR_PHY_DCR_UBG_SHIFT -#undef DDR_PHY_DCR_UBG_MASK -#define DDR_PHY_DCR_UBG_DEFVAL 0x0000040D -#define DDR_PHY_DCR_UBG_SHIFT 30 -#define DDR_PHY_DCR_UBG_MASK 0x40000000U - -/*Un-buffered DIMM Address Mirroring*/ -#undef DDR_PHY_DCR_UDIMM_DEFVAL -#undef DDR_PHY_DCR_UDIMM_SHIFT -#undef DDR_PHY_DCR_UDIMM_MASK -#define DDR_PHY_DCR_UDIMM_DEFVAL 0x0000040D -#define DDR_PHY_DCR_UDIMM_SHIFT 29 -#define DDR_PHY_DCR_UDIMM_MASK 0x20000000U - -/*DDR 2T Timing*/ -#undef DDR_PHY_DCR_DDR2T_DEFVAL -#undef DDR_PHY_DCR_DDR2T_SHIFT -#undef DDR_PHY_DCR_DDR2T_MASK -#define DDR_PHY_DCR_DDR2T_DEFVAL 0x0000040D -#define DDR_PHY_DCR_DDR2T_SHIFT 28 -#define DDR_PHY_DCR_DDR2T_MASK 0x10000000U - -/*No Simultaneous Rank Access*/ -#undef DDR_PHY_DCR_NOSRA_DEFVAL -#undef DDR_PHY_DCR_NOSRA_SHIFT -#undef DDR_PHY_DCR_NOSRA_MASK -#define DDR_PHY_DCR_NOSRA_DEFVAL 0x0000040D -#define DDR_PHY_DCR_NOSRA_SHIFT 27 -#define DDR_PHY_DCR_NOSRA_MASK 0x08000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DCR_RESERVED_26_18_DEFVAL -#undef DDR_PHY_DCR_RESERVED_26_18_SHIFT -#undef DDR_PHY_DCR_RESERVED_26_18_MASK -#define DDR_PHY_DCR_RESERVED_26_18_DEFVAL 0x0000040D -#define DDR_PHY_DCR_RESERVED_26_18_SHIFT 18 -#define DDR_PHY_DCR_RESERVED_26_18_MASK 0x07FC0000U - -/*Byte Mask*/ -#undef DDR_PHY_DCR_BYTEMASK_DEFVAL -#undef DDR_PHY_DCR_BYTEMASK_SHIFT -#undef DDR_PHY_DCR_BYTEMASK_MASK -#define DDR_PHY_DCR_BYTEMASK_DEFVAL 0x0000040D -#define DDR_PHY_DCR_BYTEMASK_SHIFT 10 -#define DDR_PHY_DCR_BYTEMASK_MASK 0x0003FC00U - -/*DDR Type*/ -#undef DDR_PHY_DCR_DDRTYPE_DEFVAL -#undef DDR_PHY_DCR_DDRTYPE_SHIFT -#undef DDR_PHY_DCR_DDRTYPE_MASK -#define DDR_PHY_DCR_DDRTYPE_DEFVAL 0x0000040D -#define DDR_PHY_DCR_DDRTYPE_SHIFT 8 -#define DDR_PHY_DCR_DDRTYPE_MASK 0x00000300U - -/*Multi-Purpose Register (MPR) DQ (DDR3 Only)*/ -#undef DDR_PHY_DCR_MPRDQ_DEFVAL -#undef DDR_PHY_DCR_MPRDQ_SHIFT -#undef DDR_PHY_DCR_MPRDQ_MASK -#define DDR_PHY_DCR_MPRDQ_DEFVAL 0x0000040D -#define DDR_PHY_DCR_MPRDQ_SHIFT 7 -#define DDR_PHY_DCR_MPRDQ_MASK 0x00000080U - -/*Primary DQ (DDR3 Only)*/ -#undef DDR_PHY_DCR_PDQ_DEFVAL -#undef DDR_PHY_DCR_PDQ_SHIFT -#undef DDR_PHY_DCR_PDQ_MASK -#define DDR_PHY_DCR_PDQ_DEFVAL 0x0000040D -#define DDR_PHY_DCR_PDQ_SHIFT 4 -#define DDR_PHY_DCR_PDQ_MASK 0x00000070U - -/*DDR 8-Bank*/ -#undef DDR_PHY_DCR_DDR8BNK_DEFVAL -#undef DDR_PHY_DCR_DDR8BNK_SHIFT -#undef DDR_PHY_DCR_DDR8BNK_MASK -#define DDR_PHY_DCR_DDR8BNK_DEFVAL 0x0000040D -#define DDR_PHY_DCR_DDR8BNK_SHIFT 3 -#define DDR_PHY_DCR_DDR8BNK_MASK 0x00000008U - -/*DDR Mode*/ -#undef DDR_PHY_DCR_DDRMD_DEFVAL -#undef DDR_PHY_DCR_DDRMD_SHIFT -#undef DDR_PHY_DCR_DDRMD_MASK -#define DDR_PHY_DCR_DDRMD_DEFVAL 0x0000040D -#define DDR_PHY_DCR_DDRMD_SHIFT 0 -#define DDR_PHY_DCR_DDRMD_MASK 0x00000007U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR0_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DTPR0_RESERVED_31_29_SHIFT -#undef DDR_PHY_DTPR0_RESERVED_31_29_MASK -#define DDR_PHY_DTPR0_RESERVED_31_29_DEFVAL 0x105A2D08 -#define DDR_PHY_DTPR0_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DTPR0_RESERVED_31_29_MASK 0xE0000000U - -/*Activate to activate command delay (different banks)*/ -#undef DDR_PHY_DTPR0_TRRD_DEFVAL -#undef DDR_PHY_DTPR0_TRRD_SHIFT -#undef DDR_PHY_DTPR0_TRRD_MASK -#define DDR_PHY_DTPR0_TRRD_DEFVAL 0x105A2D08 -#define DDR_PHY_DTPR0_TRRD_SHIFT 24 -#define DDR_PHY_DTPR0_TRRD_MASK 0x1F000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR0_RESERVED_23_DEFVAL -#undef DDR_PHY_DTPR0_RESERVED_23_SHIFT -#undef DDR_PHY_DTPR0_RESERVED_23_MASK -#define DDR_PHY_DTPR0_RESERVED_23_DEFVAL 0x105A2D08 -#define DDR_PHY_DTPR0_RESERVED_23_SHIFT 23 -#define DDR_PHY_DTPR0_RESERVED_23_MASK 0x00800000U - -/*Activate to precharge command delay*/ -#undef DDR_PHY_DTPR0_TRAS_DEFVAL -#undef DDR_PHY_DTPR0_TRAS_SHIFT -#undef DDR_PHY_DTPR0_TRAS_MASK -#define DDR_PHY_DTPR0_TRAS_DEFVAL 0x105A2D08 -#define DDR_PHY_DTPR0_TRAS_SHIFT 16 -#define DDR_PHY_DTPR0_TRAS_MASK 0x007F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR0_RESERVED_15_DEFVAL -#undef DDR_PHY_DTPR0_RESERVED_15_SHIFT -#undef DDR_PHY_DTPR0_RESERVED_15_MASK -#define DDR_PHY_DTPR0_RESERVED_15_DEFVAL 0x105A2D08 -#define DDR_PHY_DTPR0_RESERVED_15_SHIFT 15 -#define DDR_PHY_DTPR0_RESERVED_15_MASK 0x00008000U - -/*Precharge command period*/ -#undef DDR_PHY_DTPR0_TRP_DEFVAL -#undef DDR_PHY_DTPR0_TRP_SHIFT -#undef DDR_PHY_DTPR0_TRP_MASK -#define DDR_PHY_DTPR0_TRP_DEFVAL 0x105A2D08 -#define DDR_PHY_DTPR0_TRP_SHIFT 8 -#define DDR_PHY_DTPR0_TRP_MASK 0x00007F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR0_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DTPR0_RESERVED_7_5_SHIFT -#undef DDR_PHY_DTPR0_RESERVED_7_5_MASK -#define DDR_PHY_DTPR0_RESERVED_7_5_DEFVAL 0x105A2D08 -#define DDR_PHY_DTPR0_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DTPR0_RESERVED_7_5_MASK 0x000000E0U - -/*Internal read to precharge command delay*/ -#undef DDR_PHY_DTPR0_TRTP_DEFVAL -#undef DDR_PHY_DTPR0_TRTP_SHIFT -#undef DDR_PHY_DTPR0_TRTP_MASK -#define DDR_PHY_DTPR0_TRTP_DEFVAL 0x105A2D08 -#define DDR_PHY_DTPR0_TRTP_SHIFT 0 -#define DDR_PHY_DTPR0_TRTP_MASK 0x0000001FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR1_RESERVED_31_DEFVAL -#undef DDR_PHY_DTPR1_RESERVED_31_SHIFT -#undef DDR_PHY_DTPR1_RESERVED_31_MASK -#define DDR_PHY_DTPR1_RESERVED_31_DEFVAL 0x5656041E -#define DDR_PHY_DTPR1_RESERVED_31_SHIFT 31 -#define DDR_PHY_DTPR1_RESERVED_31_MASK 0x80000000U - -/*Minimum delay from when write leveling mode is programmed to the first DQS/DQS# rising edge.*/ -#undef DDR_PHY_DTPR1_TWLMRD_DEFVAL -#undef DDR_PHY_DTPR1_TWLMRD_SHIFT -#undef DDR_PHY_DTPR1_TWLMRD_MASK -#define DDR_PHY_DTPR1_TWLMRD_DEFVAL 0x5656041E -#define DDR_PHY_DTPR1_TWLMRD_SHIFT 24 -#define DDR_PHY_DTPR1_TWLMRD_MASK 0x7F000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR1_RESERVED_23_DEFVAL -#undef DDR_PHY_DTPR1_RESERVED_23_SHIFT -#undef DDR_PHY_DTPR1_RESERVED_23_MASK -#define DDR_PHY_DTPR1_RESERVED_23_DEFVAL 0x5656041E -#define DDR_PHY_DTPR1_RESERVED_23_SHIFT 23 -#define DDR_PHY_DTPR1_RESERVED_23_MASK 0x00800000U - -/*4-bank activate period*/ -#undef DDR_PHY_DTPR1_TFAW_DEFVAL -#undef DDR_PHY_DTPR1_TFAW_SHIFT -#undef DDR_PHY_DTPR1_TFAW_MASK -#define DDR_PHY_DTPR1_TFAW_DEFVAL 0x5656041E -#define DDR_PHY_DTPR1_TFAW_SHIFT 16 -#define DDR_PHY_DTPR1_TFAW_MASK 0x007F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR1_RESERVED_15_11_DEFVAL -#undef DDR_PHY_DTPR1_RESERVED_15_11_SHIFT -#undef DDR_PHY_DTPR1_RESERVED_15_11_MASK -#define DDR_PHY_DTPR1_RESERVED_15_11_DEFVAL 0x5656041E -#define DDR_PHY_DTPR1_RESERVED_15_11_SHIFT 11 -#define DDR_PHY_DTPR1_RESERVED_15_11_MASK 0x0000F800U - -/*Load mode update delay (DDR4 and DDR3 only)*/ -#undef DDR_PHY_DTPR1_TMOD_DEFVAL -#undef DDR_PHY_DTPR1_TMOD_SHIFT -#undef DDR_PHY_DTPR1_TMOD_MASK -#define DDR_PHY_DTPR1_TMOD_DEFVAL 0x5656041E -#define DDR_PHY_DTPR1_TMOD_SHIFT 8 -#define DDR_PHY_DTPR1_TMOD_MASK 0x00000700U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR1_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DTPR1_RESERVED_7_5_SHIFT -#undef DDR_PHY_DTPR1_RESERVED_7_5_MASK -#define DDR_PHY_DTPR1_RESERVED_7_5_DEFVAL 0x5656041E -#define DDR_PHY_DTPR1_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DTPR1_RESERVED_7_5_MASK 0x000000E0U - -/*Load mode cycle time*/ -#undef DDR_PHY_DTPR1_TMRD_DEFVAL -#undef DDR_PHY_DTPR1_TMRD_SHIFT -#undef DDR_PHY_DTPR1_TMRD_MASK -#define DDR_PHY_DTPR1_TMRD_DEFVAL 0x5656041E -#define DDR_PHY_DTPR1_TMRD_SHIFT 0 -#define DDR_PHY_DTPR1_TMRD_MASK 0x0000001FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR2_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DTPR2_RESERVED_31_29_SHIFT -#undef DDR_PHY_DTPR2_RESERVED_31_29_MASK -#define DDR_PHY_DTPR2_RESERVED_31_29_DEFVAL 0x000B01D0 -#define DDR_PHY_DTPR2_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DTPR2_RESERVED_31_29_MASK 0xE0000000U - -/*Read to Write command delay. Valid values are*/ -#undef DDR_PHY_DTPR2_TRTW_DEFVAL -#undef DDR_PHY_DTPR2_TRTW_SHIFT -#undef DDR_PHY_DTPR2_TRTW_MASK -#define DDR_PHY_DTPR2_TRTW_DEFVAL 0x000B01D0 -#define DDR_PHY_DTPR2_TRTW_SHIFT 28 -#define DDR_PHY_DTPR2_TRTW_MASK 0x10000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR2_RESERVED_27_25_DEFVAL -#undef DDR_PHY_DTPR2_RESERVED_27_25_SHIFT -#undef DDR_PHY_DTPR2_RESERVED_27_25_MASK -#define DDR_PHY_DTPR2_RESERVED_27_25_DEFVAL 0x000B01D0 -#define DDR_PHY_DTPR2_RESERVED_27_25_SHIFT 25 -#define DDR_PHY_DTPR2_RESERVED_27_25_MASK 0x0E000000U - -/*Read to ODT delay (DDR3 only)*/ -#undef DDR_PHY_DTPR2_TRTODT_DEFVAL -#undef DDR_PHY_DTPR2_TRTODT_SHIFT -#undef DDR_PHY_DTPR2_TRTODT_MASK -#define DDR_PHY_DTPR2_TRTODT_DEFVAL 0x000B01D0 -#define DDR_PHY_DTPR2_TRTODT_SHIFT 24 -#define DDR_PHY_DTPR2_TRTODT_MASK 0x01000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR2_RESERVED_23_20_DEFVAL -#undef DDR_PHY_DTPR2_RESERVED_23_20_SHIFT -#undef DDR_PHY_DTPR2_RESERVED_23_20_MASK -#define DDR_PHY_DTPR2_RESERVED_23_20_DEFVAL 0x000B01D0 -#define DDR_PHY_DTPR2_RESERVED_23_20_SHIFT 20 -#define DDR_PHY_DTPR2_RESERVED_23_20_MASK 0x00F00000U - -/*CKE minimum pulse width*/ -#undef DDR_PHY_DTPR2_TCKE_DEFVAL -#undef DDR_PHY_DTPR2_TCKE_SHIFT -#undef DDR_PHY_DTPR2_TCKE_MASK -#define DDR_PHY_DTPR2_TCKE_DEFVAL 0x000B01D0 -#define DDR_PHY_DTPR2_TCKE_SHIFT 16 -#define DDR_PHY_DTPR2_TCKE_MASK 0x000F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR2_RESERVED_15_10_DEFVAL -#undef DDR_PHY_DTPR2_RESERVED_15_10_SHIFT -#undef DDR_PHY_DTPR2_RESERVED_15_10_MASK -#define DDR_PHY_DTPR2_RESERVED_15_10_DEFVAL 0x000B01D0 -#define DDR_PHY_DTPR2_RESERVED_15_10_SHIFT 10 -#define DDR_PHY_DTPR2_RESERVED_15_10_MASK 0x0000FC00U - -/*Self refresh exit delay*/ -#undef DDR_PHY_DTPR2_TXS_DEFVAL -#undef DDR_PHY_DTPR2_TXS_SHIFT -#undef DDR_PHY_DTPR2_TXS_MASK -#define DDR_PHY_DTPR2_TXS_DEFVAL 0x000B01D0 -#define DDR_PHY_DTPR2_TXS_SHIFT 0 -#define DDR_PHY_DTPR2_TXS_MASK 0x000003FFU - -/*ODT turn-off delay extension*/ -#undef DDR_PHY_DTPR3_TOFDX_DEFVAL -#undef DDR_PHY_DTPR3_TOFDX_SHIFT -#undef DDR_PHY_DTPR3_TOFDX_MASK -#define DDR_PHY_DTPR3_TOFDX_DEFVAL 0x02000804 -#define DDR_PHY_DTPR3_TOFDX_SHIFT 29 -#define DDR_PHY_DTPR3_TOFDX_MASK 0xE0000000U - -/*Read to read and write to write command delay*/ -#undef DDR_PHY_DTPR3_TCCD_DEFVAL -#undef DDR_PHY_DTPR3_TCCD_SHIFT -#undef DDR_PHY_DTPR3_TCCD_MASK -#define DDR_PHY_DTPR3_TCCD_DEFVAL 0x02000804 -#define DDR_PHY_DTPR3_TCCD_SHIFT 26 -#define DDR_PHY_DTPR3_TCCD_MASK 0x1C000000U - -/*DLL locking time*/ -#undef DDR_PHY_DTPR3_TDLLK_DEFVAL -#undef DDR_PHY_DTPR3_TDLLK_SHIFT -#undef DDR_PHY_DTPR3_TDLLK_MASK -#define DDR_PHY_DTPR3_TDLLK_DEFVAL 0x02000804 -#define DDR_PHY_DTPR3_TDLLK_SHIFT 16 -#define DDR_PHY_DTPR3_TDLLK_MASK 0x03FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR3_RESERVED_15_12_DEFVAL -#undef DDR_PHY_DTPR3_RESERVED_15_12_SHIFT -#undef DDR_PHY_DTPR3_RESERVED_15_12_MASK -#define DDR_PHY_DTPR3_RESERVED_15_12_DEFVAL 0x02000804 -#define DDR_PHY_DTPR3_RESERVED_15_12_SHIFT 12 -#define DDR_PHY_DTPR3_RESERVED_15_12_MASK 0x0000F000U - -/*Maximum DQS output access time from CK/CK# (LPDDR2/3 only)*/ -#undef DDR_PHY_DTPR3_TDQSCKMAX_DEFVAL -#undef DDR_PHY_DTPR3_TDQSCKMAX_SHIFT -#undef DDR_PHY_DTPR3_TDQSCKMAX_MASK -#define DDR_PHY_DTPR3_TDQSCKMAX_DEFVAL 0x02000804 -#define DDR_PHY_DTPR3_TDQSCKMAX_SHIFT 8 -#define DDR_PHY_DTPR3_TDQSCKMAX_MASK 0x00000F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR3_RESERVED_7_3_DEFVAL -#undef DDR_PHY_DTPR3_RESERVED_7_3_SHIFT -#undef DDR_PHY_DTPR3_RESERVED_7_3_MASK -#define DDR_PHY_DTPR3_RESERVED_7_3_DEFVAL 0x02000804 -#define DDR_PHY_DTPR3_RESERVED_7_3_SHIFT 3 -#define DDR_PHY_DTPR3_RESERVED_7_3_MASK 0x000000F8U - -/*DQS output access time from CK/CK# (LPDDR2/3 only)*/ -#undef DDR_PHY_DTPR3_TDQSCK_DEFVAL -#undef DDR_PHY_DTPR3_TDQSCK_SHIFT -#undef DDR_PHY_DTPR3_TDQSCK_MASK -#define DDR_PHY_DTPR3_TDQSCK_DEFVAL 0x02000804 -#define DDR_PHY_DTPR3_TDQSCK_SHIFT 0 -#define DDR_PHY_DTPR3_TDQSCK_MASK 0x00000007U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR4_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DTPR4_RESERVED_31_30_SHIFT -#undef DDR_PHY_DTPR4_RESERVED_31_30_MASK -#define DDR_PHY_DTPR4_RESERVED_31_30_DEFVAL 0x01C02B10 -#define DDR_PHY_DTPR4_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DTPR4_RESERVED_31_30_MASK 0xC0000000U - -/*ODT turn-on/turn-off delays (DDR2 only)*/ -#undef DDR_PHY_DTPR4_TAOND_TAOFD_DEFVAL -#undef DDR_PHY_DTPR4_TAOND_TAOFD_SHIFT -#undef DDR_PHY_DTPR4_TAOND_TAOFD_MASK -#define DDR_PHY_DTPR4_TAOND_TAOFD_DEFVAL 0x01C02B10 -#define DDR_PHY_DTPR4_TAOND_TAOFD_SHIFT 28 -#define DDR_PHY_DTPR4_TAOND_TAOFD_MASK 0x30000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR4_RESERVED_27_26_DEFVAL -#undef DDR_PHY_DTPR4_RESERVED_27_26_SHIFT -#undef DDR_PHY_DTPR4_RESERVED_27_26_MASK -#define DDR_PHY_DTPR4_RESERVED_27_26_DEFVAL 0x01C02B10 -#define DDR_PHY_DTPR4_RESERVED_27_26_SHIFT 26 -#define DDR_PHY_DTPR4_RESERVED_27_26_MASK 0x0C000000U - -/*Refresh-to-Refresh*/ -#undef DDR_PHY_DTPR4_TRFC_DEFVAL -#undef DDR_PHY_DTPR4_TRFC_SHIFT -#undef DDR_PHY_DTPR4_TRFC_MASK -#define DDR_PHY_DTPR4_TRFC_DEFVAL 0x01C02B10 -#define DDR_PHY_DTPR4_TRFC_SHIFT 16 -#define DDR_PHY_DTPR4_TRFC_MASK 0x03FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR4_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DTPR4_RESERVED_15_14_SHIFT -#undef DDR_PHY_DTPR4_RESERVED_15_14_MASK -#define DDR_PHY_DTPR4_RESERVED_15_14_DEFVAL 0x01C02B10 -#define DDR_PHY_DTPR4_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DTPR4_RESERVED_15_14_MASK 0x0000C000U - -/*Write leveling output delay*/ -#undef DDR_PHY_DTPR4_TWLO_DEFVAL -#undef DDR_PHY_DTPR4_TWLO_SHIFT -#undef DDR_PHY_DTPR4_TWLO_MASK -#define DDR_PHY_DTPR4_TWLO_DEFVAL 0x01C02B10 -#define DDR_PHY_DTPR4_TWLO_SHIFT 8 -#define DDR_PHY_DTPR4_TWLO_MASK 0x00003F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR4_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DTPR4_RESERVED_7_5_SHIFT -#undef DDR_PHY_DTPR4_RESERVED_7_5_MASK -#define DDR_PHY_DTPR4_RESERVED_7_5_DEFVAL 0x01C02B10 -#define DDR_PHY_DTPR4_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DTPR4_RESERVED_7_5_MASK 0x000000E0U - -/*Power down exit delay*/ -#undef DDR_PHY_DTPR4_TXP_DEFVAL -#undef DDR_PHY_DTPR4_TXP_SHIFT -#undef DDR_PHY_DTPR4_TXP_MASK -#define DDR_PHY_DTPR4_TXP_DEFVAL 0x01C02B10 -#define DDR_PHY_DTPR4_TXP_SHIFT 0 -#define DDR_PHY_DTPR4_TXP_MASK 0x0000001FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR5_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DTPR5_RESERVED_31_24_SHIFT -#undef DDR_PHY_DTPR5_RESERVED_31_24_MASK -#define DDR_PHY_DTPR5_RESERVED_31_24_DEFVAL 0x00872716 -#define DDR_PHY_DTPR5_RESERVED_31_24_SHIFT 24 -#define DDR_PHY_DTPR5_RESERVED_31_24_MASK 0xFF000000U - -/*Activate to activate command delay (same bank)*/ -#undef DDR_PHY_DTPR5_TRC_DEFVAL -#undef DDR_PHY_DTPR5_TRC_SHIFT -#undef DDR_PHY_DTPR5_TRC_MASK -#define DDR_PHY_DTPR5_TRC_DEFVAL 0x00872716 -#define DDR_PHY_DTPR5_TRC_SHIFT 16 -#define DDR_PHY_DTPR5_TRC_MASK 0x00FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR5_RESERVED_15_DEFVAL -#undef DDR_PHY_DTPR5_RESERVED_15_SHIFT -#undef DDR_PHY_DTPR5_RESERVED_15_MASK -#define DDR_PHY_DTPR5_RESERVED_15_DEFVAL 0x00872716 -#define DDR_PHY_DTPR5_RESERVED_15_SHIFT 15 -#define DDR_PHY_DTPR5_RESERVED_15_MASK 0x00008000U - -/*Activate to read or write delay*/ -#undef DDR_PHY_DTPR5_TRCD_DEFVAL -#undef DDR_PHY_DTPR5_TRCD_SHIFT -#undef DDR_PHY_DTPR5_TRCD_MASK -#define DDR_PHY_DTPR5_TRCD_DEFVAL 0x00872716 -#define DDR_PHY_DTPR5_TRCD_SHIFT 8 -#define DDR_PHY_DTPR5_TRCD_MASK 0x00007F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR5_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DTPR5_RESERVED_7_5_SHIFT -#undef DDR_PHY_DTPR5_RESERVED_7_5_MASK -#define DDR_PHY_DTPR5_RESERVED_7_5_DEFVAL 0x00872716 -#define DDR_PHY_DTPR5_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DTPR5_RESERVED_7_5_MASK 0x000000E0U - -/*Internal write to read command delay*/ -#undef DDR_PHY_DTPR5_TWTR_DEFVAL -#undef DDR_PHY_DTPR5_TWTR_SHIFT -#undef DDR_PHY_DTPR5_TWTR_MASK -#define DDR_PHY_DTPR5_TWTR_DEFVAL 0x00872716 -#define DDR_PHY_DTPR5_TWTR_SHIFT 0 -#define DDR_PHY_DTPR5_TWTR_MASK 0x0000001FU - -/*PUB Write Latency Enable*/ -#undef DDR_PHY_DTPR6_PUBWLEN_DEFVAL -#undef DDR_PHY_DTPR6_PUBWLEN_SHIFT -#undef DDR_PHY_DTPR6_PUBWLEN_MASK -#define DDR_PHY_DTPR6_PUBWLEN_DEFVAL 0x00000505 -#define DDR_PHY_DTPR6_PUBWLEN_SHIFT 31 -#define DDR_PHY_DTPR6_PUBWLEN_MASK 0x80000000U - -/*PUB Read Latency Enable*/ -#undef DDR_PHY_DTPR6_PUBRLEN_DEFVAL -#undef DDR_PHY_DTPR6_PUBRLEN_SHIFT -#undef DDR_PHY_DTPR6_PUBRLEN_MASK -#define DDR_PHY_DTPR6_PUBRLEN_DEFVAL 0x00000505 -#define DDR_PHY_DTPR6_PUBRLEN_SHIFT 30 -#define DDR_PHY_DTPR6_PUBRLEN_MASK 0x40000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR6_RESERVED_29_14_DEFVAL -#undef DDR_PHY_DTPR6_RESERVED_29_14_SHIFT -#undef DDR_PHY_DTPR6_RESERVED_29_14_MASK -#define DDR_PHY_DTPR6_RESERVED_29_14_DEFVAL 0x00000505 -#define DDR_PHY_DTPR6_RESERVED_29_14_SHIFT 14 -#define DDR_PHY_DTPR6_RESERVED_29_14_MASK 0x3FFFC000U - -/*Write Latency*/ -#undef DDR_PHY_DTPR6_PUBWL_DEFVAL -#undef DDR_PHY_DTPR6_PUBWL_SHIFT -#undef DDR_PHY_DTPR6_PUBWL_MASK -#define DDR_PHY_DTPR6_PUBWL_DEFVAL 0x00000505 -#define DDR_PHY_DTPR6_PUBWL_SHIFT 8 -#define DDR_PHY_DTPR6_PUBWL_MASK 0x00003F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTPR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DTPR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_DTPR6_RESERVED_7_6_MASK -#define DDR_PHY_DTPR6_RESERVED_7_6_DEFVAL 0x00000505 -#define DDR_PHY_DTPR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DTPR6_RESERVED_7_6_MASK 0x000000C0U - -/*Read Latency*/ -#undef DDR_PHY_DTPR6_PUBRL_DEFVAL -#undef DDR_PHY_DTPR6_PUBRL_SHIFT -#undef DDR_PHY_DTPR6_PUBRL_MASK -#define DDR_PHY_DTPR6_PUBRL_DEFVAL 0x00000505 -#define DDR_PHY_DTPR6_PUBRL_SHIFT 0 -#define DDR_PHY_DTPR6_PUBRL_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR0_RESERVED_31_DEFVAL -#undef DDR_PHY_RDIMMGCR0_RESERVED_31_SHIFT -#undef DDR_PHY_RDIMMGCR0_RESERVED_31_MASK -#define DDR_PHY_RDIMMGCR0_RESERVED_31_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_RESERVED_31_SHIFT 31 -#define DDR_PHY_RDIMMGCR0_RESERVED_31_MASK 0x80000000U - -/*RDMIMM Quad CS Enable*/ -#undef DDR_PHY_RDIMMGCR0_QCSEN_DEFVAL -#undef DDR_PHY_RDIMMGCR0_QCSEN_SHIFT -#undef DDR_PHY_RDIMMGCR0_QCSEN_MASK -#define DDR_PHY_RDIMMGCR0_QCSEN_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_QCSEN_SHIFT 30 -#define DDR_PHY_RDIMMGCR0_QCSEN_MASK 0x40000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR0_RESERVED_29_28_DEFVAL -#undef DDR_PHY_RDIMMGCR0_RESERVED_29_28_SHIFT -#undef DDR_PHY_RDIMMGCR0_RESERVED_29_28_MASK -#define DDR_PHY_RDIMMGCR0_RESERVED_29_28_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_RESERVED_29_28_SHIFT 28 -#define DDR_PHY_RDIMMGCR0_RESERVED_29_28_MASK 0x30000000U - -/*RDIMM Outputs I/O Mode*/ -#undef DDR_PHY_RDIMMGCR0_RDIMMIOM_DEFVAL -#undef DDR_PHY_RDIMMGCR0_RDIMMIOM_SHIFT -#undef DDR_PHY_RDIMMGCR0_RDIMMIOM_MASK -#define DDR_PHY_RDIMMGCR0_RDIMMIOM_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_RDIMMIOM_SHIFT 27 -#define DDR_PHY_RDIMMGCR0_RDIMMIOM_MASK 0x08000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR0_RESERVED_26_24_DEFVAL -#undef DDR_PHY_RDIMMGCR0_RESERVED_26_24_SHIFT -#undef DDR_PHY_RDIMMGCR0_RESERVED_26_24_MASK -#define DDR_PHY_RDIMMGCR0_RESERVED_26_24_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_RESERVED_26_24_SHIFT 24 -#define DDR_PHY_RDIMMGCR0_RESERVED_26_24_MASK 0x07000000U - -/*ERROUT# Output Enable*/ -#undef DDR_PHY_RDIMMGCR0_ERROUTOE_DEFVAL -#undef DDR_PHY_RDIMMGCR0_ERROUTOE_SHIFT -#undef DDR_PHY_RDIMMGCR0_ERROUTOE_MASK -#define DDR_PHY_RDIMMGCR0_ERROUTOE_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_ERROUTOE_SHIFT 23 -#define DDR_PHY_RDIMMGCR0_ERROUTOE_MASK 0x00800000U - -/*ERROUT# I/O Mode*/ -#undef DDR_PHY_RDIMMGCR0_ERROUTIOM_DEFVAL -#undef DDR_PHY_RDIMMGCR0_ERROUTIOM_SHIFT -#undef DDR_PHY_RDIMMGCR0_ERROUTIOM_MASK -#define DDR_PHY_RDIMMGCR0_ERROUTIOM_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_ERROUTIOM_SHIFT 22 -#define DDR_PHY_RDIMMGCR0_ERROUTIOM_MASK 0x00400000U - -/*ERROUT# Power Down Receiver*/ -#undef DDR_PHY_RDIMMGCR0_ERROUTPDR_DEFVAL -#undef DDR_PHY_RDIMMGCR0_ERROUTPDR_SHIFT -#undef DDR_PHY_RDIMMGCR0_ERROUTPDR_MASK -#define DDR_PHY_RDIMMGCR0_ERROUTPDR_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_ERROUTPDR_SHIFT 21 -#define DDR_PHY_RDIMMGCR0_ERROUTPDR_MASK 0x00200000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR0_RESERVED_20_DEFVAL -#undef DDR_PHY_RDIMMGCR0_RESERVED_20_SHIFT -#undef DDR_PHY_RDIMMGCR0_RESERVED_20_MASK -#define DDR_PHY_RDIMMGCR0_RESERVED_20_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_RESERVED_20_SHIFT 20 -#define DDR_PHY_RDIMMGCR0_RESERVED_20_MASK 0x00100000U - -/*ERROUT# On-Die Termination*/ -#undef DDR_PHY_RDIMMGCR0_ERROUTODT_DEFVAL -#undef DDR_PHY_RDIMMGCR0_ERROUTODT_SHIFT -#undef DDR_PHY_RDIMMGCR0_ERROUTODT_MASK -#define DDR_PHY_RDIMMGCR0_ERROUTODT_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_ERROUTODT_SHIFT 19 -#define DDR_PHY_RDIMMGCR0_ERROUTODT_MASK 0x00080000U - -/*Load Reduced DIMM*/ -#undef DDR_PHY_RDIMMGCR0_LRDIMM_DEFVAL -#undef DDR_PHY_RDIMMGCR0_LRDIMM_SHIFT -#undef DDR_PHY_RDIMMGCR0_LRDIMM_MASK -#define DDR_PHY_RDIMMGCR0_LRDIMM_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_LRDIMM_SHIFT 18 -#define DDR_PHY_RDIMMGCR0_LRDIMM_MASK 0x00040000U - -/*PAR_IN I/O Mode*/ -#undef DDR_PHY_RDIMMGCR0_PARINIOM_DEFVAL -#undef DDR_PHY_RDIMMGCR0_PARINIOM_SHIFT -#undef DDR_PHY_RDIMMGCR0_PARINIOM_MASK -#define DDR_PHY_RDIMMGCR0_PARINIOM_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_PARINIOM_SHIFT 17 -#define DDR_PHY_RDIMMGCR0_PARINIOM_MASK 0x00020000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR0_RESERVED_16_8_DEFVAL -#undef DDR_PHY_RDIMMGCR0_RESERVED_16_8_SHIFT -#undef DDR_PHY_RDIMMGCR0_RESERVED_16_8_MASK -#define DDR_PHY_RDIMMGCR0_RESERVED_16_8_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_RESERVED_16_8_SHIFT 8 -#define DDR_PHY_RDIMMGCR0_RESERVED_16_8_MASK 0x0001FF00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD_DEFVAL -#undef DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD_SHIFT -#undef DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD_MASK -#define DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD_SHIFT 6 -#define DDR_PHY_RDIMMGCR0_RNKMRREN_RSVD_MASK 0x000000C0U - -/*Rank Mirror Enable.*/ -#undef DDR_PHY_RDIMMGCR0_RNKMRREN_DEFVAL -#undef DDR_PHY_RDIMMGCR0_RNKMRREN_SHIFT -#undef DDR_PHY_RDIMMGCR0_RNKMRREN_MASK -#define DDR_PHY_RDIMMGCR0_RNKMRREN_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_RNKMRREN_SHIFT 4 -#define DDR_PHY_RDIMMGCR0_RNKMRREN_MASK 0x00000030U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR0_RESERVED_3_DEFVAL -#undef DDR_PHY_RDIMMGCR0_RESERVED_3_SHIFT -#undef DDR_PHY_RDIMMGCR0_RESERVED_3_MASK -#define DDR_PHY_RDIMMGCR0_RESERVED_3_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_RESERVED_3_SHIFT 3 -#define DDR_PHY_RDIMMGCR0_RESERVED_3_MASK 0x00000008U - -/*Stop on Parity Error*/ -#undef DDR_PHY_RDIMMGCR0_SOPERR_DEFVAL -#undef DDR_PHY_RDIMMGCR0_SOPERR_SHIFT -#undef DDR_PHY_RDIMMGCR0_SOPERR_MASK -#define DDR_PHY_RDIMMGCR0_SOPERR_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_SOPERR_SHIFT 2 -#define DDR_PHY_RDIMMGCR0_SOPERR_MASK 0x00000004U - -/*Parity Error No Registering*/ -#undef DDR_PHY_RDIMMGCR0_ERRNOREG_DEFVAL -#undef DDR_PHY_RDIMMGCR0_ERRNOREG_SHIFT -#undef DDR_PHY_RDIMMGCR0_ERRNOREG_MASK -#define DDR_PHY_RDIMMGCR0_ERRNOREG_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_ERRNOREG_SHIFT 1 -#define DDR_PHY_RDIMMGCR0_ERRNOREG_MASK 0x00000002U - -/*Registered DIMM*/ -#undef DDR_PHY_RDIMMGCR0_RDIMM_DEFVAL -#undef DDR_PHY_RDIMMGCR0_RDIMM_SHIFT -#undef DDR_PHY_RDIMMGCR0_RDIMM_MASK -#define DDR_PHY_RDIMMGCR0_RDIMM_DEFVAL 0x08400020 -#define DDR_PHY_RDIMMGCR0_RDIMM_SHIFT 0 -#define DDR_PHY_RDIMMGCR0_RDIMM_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR1_RESERVED_31_29_DEFVAL -#undef DDR_PHY_RDIMMGCR1_RESERVED_31_29_SHIFT -#undef DDR_PHY_RDIMMGCR1_RESERVED_31_29_MASK -#define DDR_PHY_RDIMMGCR1_RESERVED_31_29_DEFVAL 0x00000C80 -#define DDR_PHY_RDIMMGCR1_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_RDIMMGCR1_RESERVED_31_29_MASK 0xE0000000U - -/*Address [17] B-side Inversion Disable*/ -#undef DDR_PHY_RDIMMGCR1_A17BID_DEFVAL -#undef DDR_PHY_RDIMMGCR1_A17BID_SHIFT -#undef DDR_PHY_RDIMMGCR1_A17BID_MASK -#define DDR_PHY_RDIMMGCR1_A17BID_DEFVAL 0x00000C80 -#define DDR_PHY_RDIMMGCR1_A17BID_SHIFT 28 -#define DDR_PHY_RDIMMGCR1_A17BID_MASK 0x10000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR1_RESERVED_27_DEFVAL -#undef DDR_PHY_RDIMMGCR1_RESERVED_27_SHIFT -#undef DDR_PHY_RDIMMGCR1_RESERVED_27_MASK -#define DDR_PHY_RDIMMGCR1_RESERVED_27_DEFVAL 0x00000C80 -#define DDR_PHY_RDIMMGCR1_RESERVED_27_SHIFT 27 -#define DDR_PHY_RDIMMGCR1_RESERVED_27_MASK 0x08000000U - -/*Command word to command word programming delay*/ -#undef DDR_PHY_RDIMMGCR1_TBCMRD_L2_DEFVAL -#undef DDR_PHY_RDIMMGCR1_TBCMRD_L2_SHIFT -#undef DDR_PHY_RDIMMGCR1_TBCMRD_L2_MASK -#define DDR_PHY_RDIMMGCR1_TBCMRD_L2_DEFVAL 0x00000C80 -#define DDR_PHY_RDIMMGCR1_TBCMRD_L2_SHIFT 24 -#define DDR_PHY_RDIMMGCR1_TBCMRD_L2_MASK 0x07000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR1_RESERVED_23_DEFVAL -#undef DDR_PHY_RDIMMGCR1_RESERVED_23_SHIFT -#undef DDR_PHY_RDIMMGCR1_RESERVED_23_MASK -#define DDR_PHY_RDIMMGCR1_RESERVED_23_DEFVAL 0x00000C80 -#define DDR_PHY_RDIMMGCR1_RESERVED_23_SHIFT 23 -#define DDR_PHY_RDIMMGCR1_RESERVED_23_MASK 0x00800000U - -/*Command word to command word programming delay*/ -#undef DDR_PHY_RDIMMGCR1_TBCMRD_L_DEFVAL -#undef DDR_PHY_RDIMMGCR1_TBCMRD_L_SHIFT -#undef DDR_PHY_RDIMMGCR1_TBCMRD_L_MASK -#define DDR_PHY_RDIMMGCR1_TBCMRD_L_DEFVAL 0x00000C80 -#define DDR_PHY_RDIMMGCR1_TBCMRD_L_SHIFT 20 -#define DDR_PHY_RDIMMGCR1_TBCMRD_L_MASK 0x00700000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR1_RESERVED_19_DEFVAL -#undef DDR_PHY_RDIMMGCR1_RESERVED_19_SHIFT -#undef DDR_PHY_RDIMMGCR1_RESERVED_19_MASK -#define DDR_PHY_RDIMMGCR1_RESERVED_19_DEFVAL 0x00000C80 -#define DDR_PHY_RDIMMGCR1_RESERVED_19_SHIFT 19 -#define DDR_PHY_RDIMMGCR1_RESERVED_19_MASK 0x00080000U - -/*Command word to command word programming delay*/ -#undef DDR_PHY_RDIMMGCR1_TBCMRD_DEFVAL -#undef DDR_PHY_RDIMMGCR1_TBCMRD_SHIFT -#undef DDR_PHY_RDIMMGCR1_TBCMRD_MASK -#define DDR_PHY_RDIMMGCR1_TBCMRD_DEFVAL 0x00000C80 -#define DDR_PHY_RDIMMGCR1_TBCMRD_SHIFT 16 -#define DDR_PHY_RDIMMGCR1_TBCMRD_MASK 0x00070000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RDIMMGCR1_RESERVED_15_14_DEFVAL -#undef DDR_PHY_RDIMMGCR1_RESERVED_15_14_SHIFT -#undef DDR_PHY_RDIMMGCR1_RESERVED_15_14_MASK -#define DDR_PHY_RDIMMGCR1_RESERVED_15_14_DEFVAL 0x00000C80 -#define DDR_PHY_RDIMMGCR1_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_RDIMMGCR1_RESERVED_15_14_MASK 0x0000C000U - -/*Stabilization time*/ -#undef DDR_PHY_RDIMMGCR1_TBCSTAB_DEFVAL -#undef DDR_PHY_RDIMMGCR1_TBCSTAB_SHIFT -#undef DDR_PHY_RDIMMGCR1_TBCSTAB_MASK -#define DDR_PHY_RDIMMGCR1_TBCSTAB_DEFVAL 0x00000C80 -#define DDR_PHY_RDIMMGCR1_TBCSTAB_SHIFT 0 -#define DDR_PHY_RDIMMGCR1_TBCSTAB_MASK 0x00003FFFU - -/*DDR4/DDR3 Control Word 7*/ -#undef DDR_PHY_RDIMMCR0_RC7_DEFVAL -#undef DDR_PHY_RDIMMCR0_RC7_SHIFT -#undef DDR_PHY_RDIMMCR0_RC7_MASK -#define DDR_PHY_RDIMMCR0_RC7_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR0_RC7_SHIFT 28 -#define DDR_PHY_RDIMMCR0_RC7_MASK 0xF0000000U - -/*DDR4 Control Word 6 (Comman space Control Word) / DDR3 Reserved*/ -#undef DDR_PHY_RDIMMCR0_RC6_DEFVAL -#undef DDR_PHY_RDIMMCR0_RC6_SHIFT -#undef DDR_PHY_RDIMMCR0_RC6_MASK -#define DDR_PHY_RDIMMCR0_RC6_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR0_RC6_SHIFT 24 -#define DDR_PHY_RDIMMCR0_RC6_MASK 0x0F000000U - -/*DDR4/DDR3 Control Word 5 (CK Driver Characteristics Control Word)*/ -#undef DDR_PHY_RDIMMCR0_RC5_DEFVAL -#undef DDR_PHY_RDIMMCR0_RC5_SHIFT -#undef DDR_PHY_RDIMMCR0_RC5_MASK -#define DDR_PHY_RDIMMCR0_RC5_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR0_RC5_SHIFT 20 -#define DDR_PHY_RDIMMCR0_RC5_MASK 0x00F00000U - -/*DDR4 Control Word 4 (ODT and CKE Signals Driver Characteristics Control Word) / DDR3 Control Word 4 (Control Signals Driver C - aracteristics Control Word)*/ -#undef DDR_PHY_RDIMMCR0_RC4_DEFVAL -#undef DDR_PHY_RDIMMCR0_RC4_SHIFT -#undef DDR_PHY_RDIMMCR0_RC4_MASK -#define DDR_PHY_RDIMMCR0_RC4_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR0_RC4_SHIFT 16 -#define DDR_PHY_RDIMMCR0_RC4_MASK 0x000F0000U - -/*DDR4 Control Word 3 (CA and CS Signals Driver Characteristics Control Word) / DDR3 Control Word 3 (Command/Address Signals Dr - ver Characteristrics Control Word)*/ -#undef DDR_PHY_RDIMMCR0_RC3_DEFVAL -#undef DDR_PHY_RDIMMCR0_RC3_SHIFT -#undef DDR_PHY_RDIMMCR0_RC3_MASK -#define DDR_PHY_RDIMMCR0_RC3_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR0_RC3_SHIFT 12 -#define DDR_PHY_RDIMMCR0_RC3_MASK 0x0000F000U - -/*DDR4 Control Word 2 (Timing and IBT Control Word) / DDR3 Control Word 2 (Timing Control Word)*/ -#undef DDR_PHY_RDIMMCR0_RC2_DEFVAL -#undef DDR_PHY_RDIMMCR0_RC2_SHIFT -#undef DDR_PHY_RDIMMCR0_RC2_MASK -#define DDR_PHY_RDIMMCR0_RC2_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR0_RC2_SHIFT 8 -#define DDR_PHY_RDIMMCR0_RC2_MASK 0x00000F00U - -/*DDR4/DDR3 Control Word 1 (Clock Driver Enable Control Word)*/ -#undef DDR_PHY_RDIMMCR0_RC1_DEFVAL -#undef DDR_PHY_RDIMMCR0_RC1_SHIFT -#undef DDR_PHY_RDIMMCR0_RC1_MASK -#define DDR_PHY_RDIMMCR0_RC1_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR0_RC1_SHIFT 4 -#define DDR_PHY_RDIMMCR0_RC1_MASK 0x000000F0U - -/*DDR4/DDR3 Control Word 0 (Global Features Control Word)*/ -#undef DDR_PHY_RDIMMCR0_RC0_DEFVAL -#undef DDR_PHY_RDIMMCR0_RC0_SHIFT -#undef DDR_PHY_RDIMMCR0_RC0_MASK -#define DDR_PHY_RDIMMCR0_RC0_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR0_RC0_SHIFT 0 -#define DDR_PHY_RDIMMCR0_RC0_MASK 0x0000000FU - -/*Control Word 15*/ -#undef DDR_PHY_RDIMMCR1_RC15_DEFVAL -#undef DDR_PHY_RDIMMCR1_RC15_SHIFT -#undef DDR_PHY_RDIMMCR1_RC15_MASK -#define DDR_PHY_RDIMMCR1_RC15_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR1_RC15_SHIFT 28 -#define DDR_PHY_RDIMMCR1_RC15_MASK 0xF0000000U - -/*DDR4 Control Word 14 (Parity Control Word) / DDR3 Reserved*/ -#undef DDR_PHY_RDIMMCR1_RC14_DEFVAL -#undef DDR_PHY_RDIMMCR1_RC14_SHIFT -#undef DDR_PHY_RDIMMCR1_RC14_MASK -#define DDR_PHY_RDIMMCR1_RC14_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR1_RC14_SHIFT 24 -#define DDR_PHY_RDIMMCR1_RC14_MASK 0x0F000000U - -/*DDR4 Control Word 13 (DIMM Configuration Control Word) / DDR3 Reserved*/ -#undef DDR_PHY_RDIMMCR1_RC13_DEFVAL -#undef DDR_PHY_RDIMMCR1_RC13_SHIFT -#undef DDR_PHY_RDIMMCR1_RC13_MASK -#define DDR_PHY_RDIMMCR1_RC13_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR1_RC13_SHIFT 20 -#define DDR_PHY_RDIMMCR1_RC13_MASK 0x00F00000U - -/*DDR4 Control Word 12 (Training Control Word) / DDR3 Reserved*/ -#undef DDR_PHY_RDIMMCR1_RC12_DEFVAL -#undef DDR_PHY_RDIMMCR1_RC12_SHIFT -#undef DDR_PHY_RDIMMCR1_RC12_MASK -#define DDR_PHY_RDIMMCR1_RC12_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR1_RC12_SHIFT 16 -#define DDR_PHY_RDIMMCR1_RC12_MASK 0x000F0000U - -/*DDR4 Control Word 11 (Operating Voltage VDD and VREFCA Source Control Word) / DDR3 Control Word 11 (Operation Voltage VDD Con - rol Word)*/ -#undef DDR_PHY_RDIMMCR1_RC11_DEFVAL -#undef DDR_PHY_RDIMMCR1_RC11_SHIFT -#undef DDR_PHY_RDIMMCR1_RC11_MASK -#define DDR_PHY_RDIMMCR1_RC11_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR1_RC11_SHIFT 12 -#define DDR_PHY_RDIMMCR1_RC11_MASK 0x0000F000U - -/*DDR4/DDR3 Control Word 10 (RDIMM Operating Speed Control Word)*/ -#undef DDR_PHY_RDIMMCR1_RC10_DEFVAL -#undef DDR_PHY_RDIMMCR1_RC10_SHIFT -#undef DDR_PHY_RDIMMCR1_RC10_MASK -#define DDR_PHY_RDIMMCR1_RC10_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR1_RC10_SHIFT 8 -#define DDR_PHY_RDIMMCR1_RC10_MASK 0x00000F00U - -/*DDR4/DDR3 Control Word 9 (Power Saving Settings Control Word)*/ -#undef DDR_PHY_RDIMMCR1_RC9_DEFVAL -#undef DDR_PHY_RDIMMCR1_RC9_SHIFT -#undef DDR_PHY_RDIMMCR1_RC9_MASK -#define DDR_PHY_RDIMMCR1_RC9_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR1_RC9_SHIFT 4 -#define DDR_PHY_RDIMMCR1_RC9_MASK 0x000000F0U - -/*DDR4 Control Word 8 (Input/Output Configuration Control Word) / DDR3 Control Word 8 (Additional Input Bus Termination Setting - Control Word)*/ -#undef DDR_PHY_RDIMMCR1_RC8_DEFVAL -#undef DDR_PHY_RDIMMCR1_RC8_SHIFT -#undef DDR_PHY_RDIMMCR1_RC8_MASK -#define DDR_PHY_RDIMMCR1_RC8_DEFVAL 0x00000000 -#define DDR_PHY_RDIMMCR1_RC8_SHIFT 0 -#define DDR_PHY_RDIMMCR1_RC8_MASK 0x0000000FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR0_RESERVED_31_8_DEFVAL -#undef DDR_PHY_MR0_RESERVED_31_8_SHIFT -#undef DDR_PHY_MR0_RESERVED_31_8_MASK -#define DDR_PHY_MR0_RESERVED_31_8_DEFVAL 0x00000052 -#define DDR_PHY_MR0_RESERVED_31_8_SHIFT 8 -#define DDR_PHY_MR0_RESERVED_31_8_MASK 0xFFFFFF00U - -/*CA Terminating Rank*/ -#undef DDR_PHY_MR0_CATR_DEFVAL -#undef DDR_PHY_MR0_CATR_SHIFT -#undef DDR_PHY_MR0_CATR_MASK -#define DDR_PHY_MR0_CATR_DEFVAL 0x00000052 -#define DDR_PHY_MR0_CATR_SHIFT 7 -#define DDR_PHY_MR0_CATR_MASK 0x00000080U - -/*Reserved. These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR0_RSVD_6_5_DEFVAL -#undef DDR_PHY_MR0_RSVD_6_5_SHIFT -#undef DDR_PHY_MR0_RSVD_6_5_MASK -#define DDR_PHY_MR0_RSVD_6_5_DEFVAL 0x00000052 -#define DDR_PHY_MR0_RSVD_6_5_SHIFT 5 -#define DDR_PHY_MR0_RSVD_6_5_MASK 0x00000060U - -/*Built-in Self-Test for RZQ*/ -#undef DDR_PHY_MR0_RZQI_DEFVAL -#undef DDR_PHY_MR0_RZQI_SHIFT -#undef DDR_PHY_MR0_RZQI_MASK -#define DDR_PHY_MR0_RZQI_DEFVAL 0x00000052 -#define DDR_PHY_MR0_RZQI_SHIFT 3 -#define DDR_PHY_MR0_RZQI_MASK 0x00000018U - -/*Reserved. These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR0_RSVD_2_0_DEFVAL -#undef DDR_PHY_MR0_RSVD_2_0_SHIFT -#undef DDR_PHY_MR0_RSVD_2_0_MASK -#define DDR_PHY_MR0_RSVD_2_0_DEFVAL 0x00000052 -#define DDR_PHY_MR0_RSVD_2_0_SHIFT 0 -#define DDR_PHY_MR0_RSVD_2_0_MASK 0x00000007U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR1_RESERVED_31_8_DEFVAL -#undef DDR_PHY_MR1_RESERVED_31_8_SHIFT -#undef DDR_PHY_MR1_RESERVED_31_8_MASK -#define DDR_PHY_MR1_RESERVED_31_8_DEFVAL 0x00000004 -#define DDR_PHY_MR1_RESERVED_31_8_SHIFT 8 -#define DDR_PHY_MR1_RESERVED_31_8_MASK 0xFFFFFF00U - -/*Read Postamble Length*/ -#undef DDR_PHY_MR1_RDPST_DEFVAL -#undef DDR_PHY_MR1_RDPST_SHIFT -#undef DDR_PHY_MR1_RDPST_MASK -#define DDR_PHY_MR1_RDPST_DEFVAL 0x00000004 -#define DDR_PHY_MR1_RDPST_SHIFT 7 -#define DDR_PHY_MR1_RDPST_MASK 0x00000080U - -/*Write-recovery for auto-precharge command*/ -#undef DDR_PHY_MR1_NWR_DEFVAL -#undef DDR_PHY_MR1_NWR_SHIFT -#undef DDR_PHY_MR1_NWR_MASK -#define DDR_PHY_MR1_NWR_DEFVAL 0x00000004 -#define DDR_PHY_MR1_NWR_SHIFT 4 -#define DDR_PHY_MR1_NWR_MASK 0x00000070U - -/*Read Preamble Length*/ -#undef DDR_PHY_MR1_RDPRE_DEFVAL -#undef DDR_PHY_MR1_RDPRE_SHIFT -#undef DDR_PHY_MR1_RDPRE_MASK -#define DDR_PHY_MR1_RDPRE_DEFVAL 0x00000004 -#define DDR_PHY_MR1_RDPRE_SHIFT 3 -#define DDR_PHY_MR1_RDPRE_MASK 0x00000008U - -/*Write Preamble Length*/ -#undef DDR_PHY_MR1_WRPRE_DEFVAL -#undef DDR_PHY_MR1_WRPRE_SHIFT -#undef DDR_PHY_MR1_WRPRE_MASK -#define DDR_PHY_MR1_WRPRE_DEFVAL 0x00000004 -#define DDR_PHY_MR1_WRPRE_SHIFT 2 -#define DDR_PHY_MR1_WRPRE_MASK 0x00000004U - -/*Burst Length*/ -#undef DDR_PHY_MR1_BL_DEFVAL -#undef DDR_PHY_MR1_BL_SHIFT -#undef DDR_PHY_MR1_BL_MASK -#define DDR_PHY_MR1_BL_DEFVAL 0x00000004 -#define DDR_PHY_MR1_BL_SHIFT 0 -#define DDR_PHY_MR1_BL_MASK 0x00000003U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR2_RESERVED_31_8_DEFVAL -#undef DDR_PHY_MR2_RESERVED_31_8_SHIFT -#undef DDR_PHY_MR2_RESERVED_31_8_MASK -#define DDR_PHY_MR2_RESERVED_31_8_DEFVAL 0x00000000 -#define DDR_PHY_MR2_RESERVED_31_8_SHIFT 8 -#define DDR_PHY_MR2_RESERVED_31_8_MASK 0xFFFFFF00U - -/*Write Leveling*/ -#undef DDR_PHY_MR2_WRL_DEFVAL -#undef DDR_PHY_MR2_WRL_SHIFT -#undef DDR_PHY_MR2_WRL_MASK -#define DDR_PHY_MR2_WRL_DEFVAL 0x00000000 -#define DDR_PHY_MR2_WRL_SHIFT 7 -#define DDR_PHY_MR2_WRL_MASK 0x00000080U - -/*Write Latency Set*/ -#undef DDR_PHY_MR2_WLS_DEFVAL -#undef DDR_PHY_MR2_WLS_SHIFT -#undef DDR_PHY_MR2_WLS_MASK -#define DDR_PHY_MR2_WLS_DEFVAL 0x00000000 -#define DDR_PHY_MR2_WLS_SHIFT 6 -#define DDR_PHY_MR2_WLS_MASK 0x00000040U - -/*Write Latency*/ -#undef DDR_PHY_MR2_WL_DEFVAL -#undef DDR_PHY_MR2_WL_SHIFT -#undef DDR_PHY_MR2_WL_MASK -#define DDR_PHY_MR2_WL_DEFVAL 0x00000000 -#define DDR_PHY_MR2_WL_SHIFT 3 -#define DDR_PHY_MR2_WL_MASK 0x00000038U - -/*Read Latency*/ -#undef DDR_PHY_MR2_RL_DEFVAL -#undef DDR_PHY_MR2_RL_SHIFT -#undef DDR_PHY_MR2_RL_MASK -#define DDR_PHY_MR2_RL_DEFVAL 0x00000000 -#define DDR_PHY_MR2_RL_SHIFT 0 -#define DDR_PHY_MR2_RL_MASK 0x00000007U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR3_RESERVED_31_8_DEFVAL -#undef DDR_PHY_MR3_RESERVED_31_8_SHIFT -#undef DDR_PHY_MR3_RESERVED_31_8_MASK -#define DDR_PHY_MR3_RESERVED_31_8_DEFVAL 0x00000031 -#define DDR_PHY_MR3_RESERVED_31_8_SHIFT 8 -#define DDR_PHY_MR3_RESERVED_31_8_MASK 0xFFFFFF00U - -/*DBI-Write Enable*/ -#undef DDR_PHY_MR3_DBIWR_DEFVAL -#undef DDR_PHY_MR3_DBIWR_SHIFT -#undef DDR_PHY_MR3_DBIWR_MASK -#define DDR_PHY_MR3_DBIWR_DEFVAL 0x00000031 -#define DDR_PHY_MR3_DBIWR_SHIFT 7 -#define DDR_PHY_MR3_DBIWR_MASK 0x00000080U - -/*DBI-Read Enable*/ -#undef DDR_PHY_MR3_DBIRD_DEFVAL -#undef DDR_PHY_MR3_DBIRD_SHIFT -#undef DDR_PHY_MR3_DBIRD_MASK -#define DDR_PHY_MR3_DBIRD_DEFVAL 0x00000031 -#define DDR_PHY_MR3_DBIRD_SHIFT 6 -#define DDR_PHY_MR3_DBIRD_MASK 0x00000040U - -/*Pull-down Drive Strength*/ -#undef DDR_PHY_MR3_PDDS_DEFVAL -#undef DDR_PHY_MR3_PDDS_SHIFT -#undef DDR_PHY_MR3_PDDS_MASK -#define DDR_PHY_MR3_PDDS_DEFVAL 0x00000031 -#define DDR_PHY_MR3_PDDS_SHIFT 3 -#define DDR_PHY_MR3_PDDS_MASK 0x00000038U - -/*These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR3_RSVD_DEFVAL -#undef DDR_PHY_MR3_RSVD_SHIFT -#undef DDR_PHY_MR3_RSVD_MASK -#define DDR_PHY_MR3_RSVD_DEFVAL 0x00000031 -#define DDR_PHY_MR3_RSVD_SHIFT 2 -#define DDR_PHY_MR3_RSVD_MASK 0x00000004U - -/*Write Postamble Length*/ -#undef DDR_PHY_MR3_WRPST_DEFVAL -#undef DDR_PHY_MR3_WRPST_SHIFT -#undef DDR_PHY_MR3_WRPST_MASK -#define DDR_PHY_MR3_WRPST_DEFVAL 0x00000031 -#define DDR_PHY_MR3_WRPST_SHIFT 1 -#define DDR_PHY_MR3_WRPST_MASK 0x00000002U - -/*Pull-up Calibration Point*/ -#undef DDR_PHY_MR3_PUCAL_DEFVAL -#undef DDR_PHY_MR3_PUCAL_SHIFT -#undef DDR_PHY_MR3_PUCAL_MASK -#define DDR_PHY_MR3_PUCAL_DEFVAL 0x00000031 -#define DDR_PHY_MR3_PUCAL_SHIFT 0 -#define DDR_PHY_MR3_PUCAL_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR4_RESERVED_31_16_DEFVAL -#undef DDR_PHY_MR4_RESERVED_31_16_SHIFT -#undef DDR_PHY_MR4_RESERVED_31_16_MASK -#define DDR_PHY_MR4_RESERVED_31_16_DEFVAL 0x00000000 -#define DDR_PHY_MR4_RESERVED_31_16_SHIFT 16 -#define DDR_PHY_MR4_RESERVED_31_16_MASK 0xFFFF0000U - -/*These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR4_RSVD_15_13_DEFVAL -#undef DDR_PHY_MR4_RSVD_15_13_SHIFT -#undef DDR_PHY_MR4_RSVD_15_13_MASK -#define DDR_PHY_MR4_RSVD_15_13_DEFVAL 0x00000000 -#define DDR_PHY_MR4_RSVD_15_13_SHIFT 13 -#define DDR_PHY_MR4_RSVD_15_13_MASK 0x0000E000U - -/*Write Preamble*/ -#undef DDR_PHY_MR4_WRP_DEFVAL -#undef DDR_PHY_MR4_WRP_SHIFT -#undef DDR_PHY_MR4_WRP_MASK -#define DDR_PHY_MR4_WRP_DEFVAL 0x00000000 -#define DDR_PHY_MR4_WRP_SHIFT 12 -#define DDR_PHY_MR4_WRP_MASK 0x00001000U - -/*Read Preamble*/ -#undef DDR_PHY_MR4_RDP_DEFVAL -#undef DDR_PHY_MR4_RDP_SHIFT -#undef DDR_PHY_MR4_RDP_MASK -#define DDR_PHY_MR4_RDP_DEFVAL 0x00000000 -#define DDR_PHY_MR4_RDP_SHIFT 11 -#define DDR_PHY_MR4_RDP_MASK 0x00000800U - -/*Read Preamble Training Mode*/ -#undef DDR_PHY_MR4_RPTM_DEFVAL -#undef DDR_PHY_MR4_RPTM_SHIFT -#undef DDR_PHY_MR4_RPTM_MASK -#define DDR_PHY_MR4_RPTM_DEFVAL 0x00000000 -#define DDR_PHY_MR4_RPTM_SHIFT 10 -#define DDR_PHY_MR4_RPTM_MASK 0x00000400U - -/*Self Refresh Abort*/ -#undef DDR_PHY_MR4_SRA_DEFVAL -#undef DDR_PHY_MR4_SRA_SHIFT -#undef DDR_PHY_MR4_SRA_MASK -#define DDR_PHY_MR4_SRA_DEFVAL 0x00000000 -#define DDR_PHY_MR4_SRA_SHIFT 9 -#define DDR_PHY_MR4_SRA_MASK 0x00000200U - -/*CS to Command Latency Mode*/ -#undef DDR_PHY_MR4_CS2CMDL_DEFVAL -#undef DDR_PHY_MR4_CS2CMDL_SHIFT -#undef DDR_PHY_MR4_CS2CMDL_MASK -#define DDR_PHY_MR4_CS2CMDL_DEFVAL 0x00000000 -#define DDR_PHY_MR4_CS2CMDL_SHIFT 6 -#define DDR_PHY_MR4_CS2CMDL_MASK 0x000001C0U - -/*These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR4_RSVD1_DEFVAL -#undef DDR_PHY_MR4_RSVD1_SHIFT -#undef DDR_PHY_MR4_RSVD1_MASK -#define DDR_PHY_MR4_RSVD1_DEFVAL 0x00000000 -#define DDR_PHY_MR4_RSVD1_SHIFT 5 -#define DDR_PHY_MR4_RSVD1_MASK 0x00000020U - -/*Internal VREF Monitor*/ -#undef DDR_PHY_MR4_IVM_DEFVAL -#undef DDR_PHY_MR4_IVM_SHIFT -#undef DDR_PHY_MR4_IVM_MASK -#define DDR_PHY_MR4_IVM_DEFVAL 0x00000000 -#define DDR_PHY_MR4_IVM_SHIFT 4 -#define DDR_PHY_MR4_IVM_MASK 0x00000010U - -/*Temperature Controlled Refresh Mode*/ -#undef DDR_PHY_MR4_TCRM_DEFVAL -#undef DDR_PHY_MR4_TCRM_SHIFT -#undef DDR_PHY_MR4_TCRM_MASK -#define DDR_PHY_MR4_TCRM_DEFVAL 0x00000000 -#define DDR_PHY_MR4_TCRM_SHIFT 3 -#define DDR_PHY_MR4_TCRM_MASK 0x00000008U - -/*Temperature Controlled Refresh Range*/ -#undef DDR_PHY_MR4_TCRR_DEFVAL -#undef DDR_PHY_MR4_TCRR_SHIFT -#undef DDR_PHY_MR4_TCRR_MASK -#define DDR_PHY_MR4_TCRR_DEFVAL 0x00000000 -#define DDR_PHY_MR4_TCRR_SHIFT 2 -#define DDR_PHY_MR4_TCRR_MASK 0x00000004U - -/*Maximum Power Down Mode*/ -#undef DDR_PHY_MR4_MPDM_DEFVAL -#undef DDR_PHY_MR4_MPDM_SHIFT -#undef DDR_PHY_MR4_MPDM_MASK -#define DDR_PHY_MR4_MPDM_DEFVAL 0x00000000 -#define DDR_PHY_MR4_MPDM_SHIFT 1 -#define DDR_PHY_MR4_MPDM_MASK 0x00000002U - -/*This is a JEDEC reserved bit and is recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR4_RSVD_0_DEFVAL -#undef DDR_PHY_MR4_RSVD_0_SHIFT -#undef DDR_PHY_MR4_RSVD_0_MASK -#define DDR_PHY_MR4_RSVD_0_DEFVAL 0x00000000 -#define DDR_PHY_MR4_RSVD_0_SHIFT 0 -#define DDR_PHY_MR4_RSVD_0_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR5_RESERVED_31_16_DEFVAL -#undef DDR_PHY_MR5_RESERVED_31_16_SHIFT -#undef DDR_PHY_MR5_RESERVED_31_16_MASK -#define DDR_PHY_MR5_RESERVED_31_16_DEFVAL 0x00000000 -#define DDR_PHY_MR5_RESERVED_31_16_SHIFT 16 -#define DDR_PHY_MR5_RESERVED_31_16_MASK 0xFFFF0000U - -/*These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR5_RSVD_DEFVAL -#undef DDR_PHY_MR5_RSVD_SHIFT -#undef DDR_PHY_MR5_RSVD_MASK -#define DDR_PHY_MR5_RSVD_DEFVAL 0x00000000 -#define DDR_PHY_MR5_RSVD_SHIFT 13 -#define DDR_PHY_MR5_RSVD_MASK 0x0000E000U - -/*Read DBI*/ -#undef DDR_PHY_MR5_RDBI_DEFVAL -#undef DDR_PHY_MR5_RDBI_SHIFT -#undef DDR_PHY_MR5_RDBI_MASK -#define DDR_PHY_MR5_RDBI_DEFVAL 0x00000000 -#define DDR_PHY_MR5_RDBI_SHIFT 12 -#define DDR_PHY_MR5_RDBI_MASK 0x00001000U - -/*Write DBI*/ -#undef DDR_PHY_MR5_WDBI_DEFVAL -#undef DDR_PHY_MR5_WDBI_SHIFT -#undef DDR_PHY_MR5_WDBI_MASK -#define DDR_PHY_MR5_WDBI_DEFVAL 0x00000000 -#define DDR_PHY_MR5_WDBI_SHIFT 11 -#define DDR_PHY_MR5_WDBI_MASK 0x00000800U - -/*Data Mask*/ -#undef DDR_PHY_MR5_DM_DEFVAL -#undef DDR_PHY_MR5_DM_SHIFT -#undef DDR_PHY_MR5_DM_MASK -#define DDR_PHY_MR5_DM_DEFVAL 0x00000000 -#define DDR_PHY_MR5_DM_SHIFT 10 -#define DDR_PHY_MR5_DM_MASK 0x00000400U - -/*CA Parity Persistent Error*/ -#undef DDR_PHY_MR5_CAPPE_DEFVAL -#undef DDR_PHY_MR5_CAPPE_SHIFT -#undef DDR_PHY_MR5_CAPPE_MASK -#define DDR_PHY_MR5_CAPPE_DEFVAL 0x00000000 -#define DDR_PHY_MR5_CAPPE_SHIFT 9 -#define DDR_PHY_MR5_CAPPE_MASK 0x00000200U - -/*RTT_PARK*/ -#undef DDR_PHY_MR5_RTTPARK_DEFVAL -#undef DDR_PHY_MR5_RTTPARK_SHIFT -#undef DDR_PHY_MR5_RTTPARK_MASK -#define DDR_PHY_MR5_RTTPARK_DEFVAL 0x00000000 -#define DDR_PHY_MR5_RTTPARK_SHIFT 6 -#define DDR_PHY_MR5_RTTPARK_MASK 0x000001C0U - -/*ODT Input Buffer during Power Down mode*/ -#undef DDR_PHY_MR5_ODTIBPD_DEFVAL -#undef DDR_PHY_MR5_ODTIBPD_SHIFT -#undef DDR_PHY_MR5_ODTIBPD_MASK -#define DDR_PHY_MR5_ODTIBPD_DEFVAL 0x00000000 -#define DDR_PHY_MR5_ODTIBPD_SHIFT 5 -#define DDR_PHY_MR5_ODTIBPD_MASK 0x00000020U - -/*C/A Parity Error Status*/ -#undef DDR_PHY_MR5_CAPES_DEFVAL -#undef DDR_PHY_MR5_CAPES_SHIFT -#undef DDR_PHY_MR5_CAPES_MASK -#define DDR_PHY_MR5_CAPES_DEFVAL 0x00000000 -#define DDR_PHY_MR5_CAPES_SHIFT 4 -#define DDR_PHY_MR5_CAPES_MASK 0x00000010U - -/*CRC Error Clear*/ -#undef DDR_PHY_MR5_CRCEC_DEFVAL -#undef DDR_PHY_MR5_CRCEC_SHIFT -#undef DDR_PHY_MR5_CRCEC_MASK -#define DDR_PHY_MR5_CRCEC_DEFVAL 0x00000000 -#define DDR_PHY_MR5_CRCEC_SHIFT 3 -#define DDR_PHY_MR5_CRCEC_MASK 0x00000008U - -/*C/A Parity Latency Mode*/ -#undef DDR_PHY_MR5_CAPM_DEFVAL -#undef DDR_PHY_MR5_CAPM_SHIFT -#undef DDR_PHY_MR5_CAPM_MASK -#define DDR_PHY_MR5_CAPM_DEFVAL 0x00000000 -#define DDR_PHY_MR5_CAPM_SHIFT 0 -#define DDR_PHY_MR5_CAPM_MASK 0x00000007U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR6_RESERVED_31_16_DEFVAL -#undef DDR_PHY_MR6_RESERVED_31_16_SHIFT -#undef DDR_PHY_MR6_RESERVED_31_16_MASK -#define DDR_PHY_MR6_RESERVED_31_16_DEFVAL 0x00000000 -#define DDR_PHY_MR6_RESERVED_31_16_SHIFT 16 -#define DDR_PHY_MR6_RESERVED_31_16_MASK 0xFFFF0000U - -/*These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR6_RSVD_15_13_DEFVAL -#undef DDR_PHY_MR6_RSVD_15_13_SHIFT -#undef DDR_PHY_MR6_RSVD_15_13_MASK -#define DDR_PHY_MR6_RSVD_15_13_DEFVAL 0x00000000 -#define DDR_PHY_MR6_RSVD_15_13_SHIFT 13 -#define DDR_PHY_MR6_RSVD_15_13_MASK 0x0000E000U - -/*CAS_n to CAS_n command delay for same bank group (tCCD_L)*/ -#undef DDR_PHY_MR6_TCCDL_DEFVAL -#undef DDR_PHY_MR6_TCCDL_SHIFT -#undef DDR_PHY_MR6_TCCDL_MASK -#define DDR_PHY_MR6_TCCDL_DEFVAL 0x00000000 -#define DDR_PHY_MR6_TCCDL_SHIFT 10 -#define DDR_PHY_MR6_TCCDL_MASK 0x00001C00U - -/*These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR6_RSVD_9_8_DEFVAL -#undef DDR_PHY_MR6_RSVD_9_8_SHIFT -#undef DDR_PHY_MR6_RSVD_9_8_MASK -#define DDR_PHY_MR6_RSVD_9_8_DEFVAL 0x00000000 -#define DDR_PHY_MR6_RSVD_9_8_SHIFT 8 -#define DDR_PHY_MR6_RSVD_9_8_MASK 0x00000300U - -/*VrefDQ Training Enable*/ -#undef DDR_PHY_MR6_VDDQTEN_DEFVAL -#undef DDR_PHY_MR6_VDDQTEN_SHIFT -#undef DDR_PHY_MR6_VDDQTEN_MASK -#define DDR_PHY_MR6_VDDQTEN_DEFVAL 0x00000000 -#define DDR_PHY_MR6_VDDQTEN_SHIFT 7 -#define DDR_PHY_MR6_VDDQTEN_MASK 0x00000080U - -/*VrefDQ Training Range*/ -#undef DDR_PHY_MR6_VDQTRG_DEFVAL -#undef DDR_PHY_MR6_VDQTRG_SHIFT -#undef DDR_PHY_MR6_VDQTRG_MASK -#define DDR_PHY_MR6_VDQTRG_DEFVAL 0x00000000 -#define DDR_PHY_MR6_VDQTRG_SHIFT 6 -#define DDR_PHY_MR6_VDQTRG_MASK 0x00000040U - -/*VrefDQ Training Values*/ -#undef DDR_PHY_MR6_VDQTVAL_DEFVAL -#undef DDR_PHY_MR6_VDQTVAL_SHIFT -#undef DDR_PHY_MR6_VDQTVAL_MASK -#define DDR_PHY_MR6_VDQTVAL_DEFVAL 0x00000000 -#define DDR_PHY_MR6_VDQTVAL_SHIFT 0 -#define DDR_PHY_MR6_VDQTVAL_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR11_RESERVED_31_8_DEFVAL -#undef DDR_PHY_MR11_RESERVED_31_8_SHIFT -#undef DDR_PHY_MR11_RESERVED_31_8_MASK -#define DDR_PHY_MR11_RESERVED_31_8_DEFVAL 0x00000000 -#define DDR_PHY_MR11_RESERVED_31_8_SHIFT 8 -#define DDR_PHY_MR11_RESERVED_31_8_MASK 0xFFFFFF00U - -/*These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR11_RSVD_DEFVAL -#undef DDR_PHY_MR11_RSVD_SHIFT -#undef DDR_PHY_MR11_RSVD_MASK -#define DDR_PHY_MR11_RSVD_DEFVAL 0x00000000 -#define DDR_PHY_MR11_RSVD_SHIFT 3 -#define DDR_PHY_MR11_RSVD_MASK 0x000000F8U - -/*Power Down Control*/ -#undef DDR_PHY_MR11_PDCTL_DEFVAL -#undef DDR_PHY_MR11_PDCTL_SHIFT -#undef DDR_PHY_MR11_PDCTL_MASK -#define DDR_PHY_MR11_PDCTL_DEFVAL 0x00000000 -#define DDR_PHY_MR11_PDCTL_SHIFT 2 -#define DDR_PHY_MR11_PDCTL_MASK 0x00000004U - -/*DQ Bus Receiver On-Die-Termination*/ -#undef DDR_PHY_MR11_DQODT_DEFVAL -#undef DDR_PHY_MR11_DQODT_SHIFT -#undef DDR_PHY_MR11_DQODT_MASK -#define DDR_PHY_MR11_DQODT_DEFVAL 0x00000000 -#define DDR_PHY_MR11_DQODT_SHIFT 0 -#define DDR_PHY_MR11_DQODT_MASK 0x00000003U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR12_RESERVED_31_8_DEFVAL -#undef DDR_PHY_MR12_RESERVED_31_8_SHIFT -#undef DDR_PHY_MR12_RESERVED_31_8_MASK -#define DDR_PHY_MR12_RESERVED_31_8_DEFVAL 0x0000004D -#define DDR_PHY_MR12_RESERVED_31_8_SHIFT 8 -#define DDR_PHY_MR12_RESERVED_31_8_MASK 0xFFFFFF00U - -/*These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR12_RSVD_DEFVAL -#undef DDR_PHY_MR12_RSVD_SHIFT -#undef DDR_PHY_MR12_RSVD_MASK -#define DDR_PHY_MR12_RSVD_DEFVAL 0x0000004D -#define DDR_PHY_MR12_RSVD_SHIFT 7 -#define DDR_PHY_MR12_RSVD_MASK 0x00000080U - -/*VREF_CA Range Select.*/ -#undef DDR_PHY_MR12_VR_CA_DEFVAL -#undef DDR_PHY_MR12_VR_CA_SHIFT -#undef DDR_PHY_MR12_VR_CA_MASK -#define DDR_PHY_MR12_VR_CA_DEFVAL 0x0000004D -#define DDR_PHY_MR12_VR_CA_SHIFT 6 -#define DDR_PHY_MR12_VR_CA_MASK 0x00000040U - -/*Controls the VREF(ca) levels for Frequency-Set-Point[1:0].*/ -#undef DDR_PHY_MR12_VREF_CA_DEFVAL -#undef DDR_PHY_MR12_VREF_CA_SHIFT -#undef DDR_PHY_MR12_VREF_CA_MASK -#define DDR_PHY_MR12_VREF_CA_DEFVAL 0x0000004D -#define DDR_PHY_MR12_VREF_CA_SHIFT 0 -#define DDR_PHY_MR12_VREF_CA_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR13_RESERVED_31_8_DEFVAL -#undef DDR_PHY_MR13_RESERVED_31_8_SHIFT -#undef DDR_PHY_MR13_RESERVED_31_8_MASK -#define DDR_PHY_MR13_RESERVED_31_8_DEFVAL 0x00000000 -#define DDR_PHY_MR13_RESERVED_31_8_SHIFT 8 -#define DDR_PHY_MR13_RESERVED_31_8_MASK 0xFFFFFF00U - -/*Frequency Set Point Operation Mode*/ -#undef DDR_PHY_MR13_FSPOP_DEFVAL -#undef DDR_PHY_MR13_FSPOP_SHIFT -#undef DDR_PHY_MR13_FSPOP_MASK -#define DDR_PHY_MR13_FSPOP_DEFVAL 0x00000000 -#define DDR_PHY_MR13_FSPOP_SHIFT 7 -#define DDR_PHY_MR13_FSPOP_MASK 0x00000080U - -/*Frequency Set Point Write Enable*/ -#undef DDR_PHY_MR13_FSPWR_DEFVAL -#undef DDR_PHY_MR13_FSPWR_SHIFT -#undef DDR_PHY_MR13_FSPWR_MASK -#define DDR_PHY_MR13_FSPWR_DEFVAL 0x00000000 -#define DDR_PHY_MR13_FSPWR_SHIFT 6 -#define DDR_PHY_MR13_FSPWR_MASK 0x00000040U - -/*Data Mask Enable*/ -#undef DDR_PHY_MR13_DMD_DEFVAL -#undef DDR_PHY_MR13_DMD_SHIFT -#undef DDR_PHY_MR13_DMD_MASK -#define DDR_PHY_MR13_DMD_DEFVAL 0x00000000 -#define DDR_PHY_MR13_DMD_SHIFT 5 -#define DDR_PHY_MR13_DMD_MASK 0x00000020U - -/*Refresh Rate Option*/ -#undef DDR_PHY_MR13_RRO_DEFVAL -#undef DDR_PHY_MR13_RRO_SHIFT -#undef DDR_PHY_MR13_RRO_MASK -#define DDR_PHY_MR13_RRO_DEFVAL 0x00000000 -#define DDR_PHY_MR13_RRO_SHIFT 4 -#define DDR_PHY_MR13_RRO_MASK 0x00000010U - -/*VREF Current Generator*/ -#undef DDR_PHY_MR13_VRCG_DEFVAL -#undef DDR_PHY_MR13_VRCG_SHIFT -#undef DDR_PHY_MR13_VRCG_MASK -#define DDR_PHY_MR13_VRCG_DEFVAL 0x00000000 -#define DDR_PHY_MR13_VRCG_SHIFT 3 -#define DDR_PHY_MR13_VRCG_MASK 0x00000008U - -/*VREF Output*/ -#undef DDR_PHY_MR13_VRO_DEFVAL -#undef DDR_PHY_MR13_VRO_SHIFT -#undef DDR_PHY_MR13_VRO_MASK -#define DDR_PHY_MR13_VRO_DEFVAL 0x00000000 -#define DDR_PHY_MR13_VRO_SHIFT 2 -#define DDR_PHY_MR13_VRO_MASK 0x00000004U - -/*Read Preamble Training Mode*/ -#undef DDR_PHY_MR13_RPT_DEFVAL -#undef DDR_PHY_MR13_RPT_SHIFT -#undef DDR_PHY_MR13_RPT_MASK -#define DDR_PHY_MR13_RPT_DEFVAL 0x00000000 -#define DDR_PHY_MR13_RPT_SHIFT 1 -#define DDR_PHY_MR13_RPT_MASK 0x00000002U - -/*Command Bus Training*/ -#undef DDR_PHY_MR13_CBT_DEFVAL -#undef DDR_PHY_MR13_CBT_SHIFT -#undef DDR_PHY_MR13_CBT_MASK -#define DDR_PHY_MR13_CBT_DEFVAL 0x00000000 -#define DDR_PHY_MR13_CBT_SHIFT 0 -#define DDR_PHY_MR13_CBT_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR14_RESERVED_31_8_DEFVAL -#undef DDR_PHY_MR14_RESERVED_31_8_SHIFT -#undef DDR_PHY_MR14_RESERVED_31_8_MASK -#define DDR_PHY_MR14_RESERVED_31_8_DEFVAL 0x0000004D -#define DDR_PHY_MR14_RESERVED_31_8_SHIFT 8 -#define DDR_PHY_MR14_RESERVED_31_8_MASK 0xFFFFFF00U - -/*These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR14_RSVD_DEFVAL -#undef DDR_PHY_MR14_RSVD_SHIFT -#undef DDR_PHY_MR14_RSVD_MASK -#define DDR_PHY_MR14_RSVD_DEFVAL 0x0000004D -#define DDR_PHY_MR14_RSVD_SHIFT 7 -#define DDR_PHY_MR14_RSVD_MASK 0x00000080U - -/*VREFDQ Range Selects.*/ -#undef DDR_PHY_MR14_VR_DQ_DEFVAL -#undef DDR_PHY_MR14_VR_DQ_SHIFT -#undef DDR_PHY_MR14_VR_DQ_MASK -#define DDR_PHY_MR14_VR_DQ_DEFVAL 0x0000004D -#define DDR_PHY_MR14_VR_DQ_SHIFT 6 -#define DDR_PHY_MR14_VR_DQ_MASK 0x00000040U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR14_VREF_DQ_DEFVAL -#undef DDR_PHY_MR14_VREF_DQ_SHIFT -#undef DDR_PHY_MR14_VREF_DQ_MASK -#define DDR_PHY_MR14_VREF_DQ_DEFVAL 0x0000004D -#define DDR_PHY_MR14_VREF_DQ_SHIFT 0 -#define DDR_PHY_MR14_VREF_DQ_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_MR22_RESERVED_31_8_DEFVAL -#undef DDR_PHY_MR22_RESERVED_31_8_SHIFT -#undef DDR_PHY_MR22_RESERVED_31_8_MASK -#define DDR_PHY_MR22_RESERVED_31_8_DEFVAL 0x00000000 -#define DDR_PHY_MR22_RESERVED_31_8_SHIFT 8 -#define DDR_PHY_MR22_RESERVED_31_8_MASK 0xFFFFFF00U - -/*These are JEDEC reserved bits and are recommended by JEDEC to be programmed to 0x0.*/ -#undef DDR_PHY_MR22_RSVD_DEFVAL -#undef DDR_PHY_MR22_RSVD_SHIFT -#undef DDR_PHY_MR22_RSVD_MASK -#define DDR_PHY_MR22_RSVD_DEFVAL 0x00000000 -#define DDR_PHY_MR22_RSVD_SHIFT 6 -#define DDR_PHY_MR22_RSVD_MASK 0x000000C0U - -/*CA ODT termination disable.*/ -#undef DDR_PHY_MR22_ODTD_CA_DEFVAL -#undef DDR_PHY_MR22_ODTD_CA_SHIFT -#undef DDR_PHY_MR22_ODTD_CA_MASK -#define DDR_PHY_MR22_ODTD_CA_DEFVAL 0x00000000 -#define DDR_PHY_MR22_ODTD_CA_SHIFT 5 -#define DDR_PHY_MR22_ODTD_CA_MASK 0x00000020U - -/*ODT CS override.*/ -#undef DDR_PHY_MR22_ODTE_CS_DEFVAL -#undef DDR_PHY_MR22_ODTE_CS_SHIFT -#undef DDR_PHY_MR22_ODTE_CS_MASK -#define DDR_PHY_MR22_ODTE_CS_DEFVAL 0x00000000 -#define DDR_PHY_MR22_ODTE_CS_SHIFT 4 -#define DDR_PHY_MR22_ODTE_CS_MASK 0x00000010U - -/*ODT CK override.*/ -#undef DDR_PHY_MR22_ODTE_CK_DEFVAL -#undef DDR_PHY_MR22_ODTE_CK_SHIFT -#undef DDR_PHY_MR22_ODTE_CK_MASK -#define DDR_PHY_MR22_ODTE_CK_DEFVAL 0x00000000 -#define DDR_PHY_MR22_ODTE_CK_SHIFT 3 -#define DDR_PHY_MR22_ODTE_CK_MASK 0x00000008U - -/*Controller ODT value for VOH calibration.*/ -#undef DDR_PHY_MR22_CODT_DEFVAL -#undef DDR_PHY_MR22_CODT_SHIFT -#undef DDR_PHY_MR22_CODT_MASK -#define DDR_PHY_MR22_CODT_DEFVAL 0x00000000 -#define DDR_PHY_MR22_CODT_SHIFT 0 -#define DDR_PHY_MR22_CODT_MASK 0x00000007U - -/*Refresh During Training*/ -#undef DDR_PHY_DTCR0_RFSHDT_DEFVAL -#undef DDR_PHY_DTCR0_RFSHDT_SHIFT -#undef DDR_PHY_DTCR0_RFSHDT_MASK -#define DDR_PHY_DTCR0_RFSHDT_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_RFSHDT_SHIFT 28 -#define DDR_PHY_DTCR0_RFSHDT_MASK 0xF0000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTCR0_RESERVED_27_26_DEFVAL -#undef DDR_PHY_DTCR0_RESERVED_27_26_SHIFT -#undef DDR_PHY_DTCR0_RESERVED_27_26_MASK -#define DDR_PHY_DTCR0_RESERVED_27_26_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_RESERVED_27_26_SHIFT 26 -#define DDR_PHY_DTCR0_RESERVED_27_26_MASK 0x0C000000U - -/*Data Training Debug Rank Select*/ -#undef DDR_PHY_DTCR0_DTDRS_DEFVAL -#undef DDR_PHY_DTCR0_DTDRS_SHIFT -#undef DDR_PHY_DTCR0_DTDRS_MASK -#define DDR_PHY_DTCR0_DTDRS_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTDRS_SHIFT 24 -#define DDR_PHY_DTCR0_DTDRS_MASK 0x03000000U - -/*Data Training with Early/Extended Gate*/ -#undef DDR_PHY_DTCR0_DTEXG_DEFVAL -#undef DDR_PHY_DTCR0_DTEXG_SHIFT -#undef DDR_PHY_DTCR0_DTEXG_MASK -#define DDR_PHY_DTCR0_DTEXG_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTEXG_SHIFT 23 -#define DDR_PHY_DTCR0_DTEXG_MASK 0x00800000U - -/*Data Training Extended Write DQS*/ -#undef DDR_PHY_DTCR0_DTEXD_DEFVAL -#undef DDR_PHY_DTCR0_DTEXD_SHIFT -#undef DDR_PHY_DTCR0_DTEXD_MASK -#define DDR_PHY_DTCR0_DTEXD_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTEXD_SHIFT 22 -#define DDR_PHY_DTCR0_DTEXD_MASK 0x00400000U - -/*Data Training Debug Step*/ -#undef DDR_PHY_DTCR0_DTDSTP_DEFVAL -#undef DDR_PHY_DTCR0_DTDSTP_SHIFT -#undef DDR_PHY_DTCR0_DTDSTP_MASK -#define DDR_PHY_DTCR0_DTDSTP_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTDSTP_SHIFT 21 -#define DDR_PHY_DTCR0_DTDSTP_MASK 0x00200000U - -/*Data Training Debug Enable*/ -#undef DDR_PHY_DTCR0_DTDEN_DEFVAL -#undef DDR_PHY_DTCR0_DTDEN_SHIFT -#undef DDR_PHY_DTCR0_DTDEN_MASK -#define DDR_PHY_DTCR0_DTDEN_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTDEN_SHIFT 20 -#define DDR_PHY_DTCR0_DTDEN_MASK 0x00100000U - -/*Data Training Debug Byte Select*/ -#undef DDR_PHY_DTCR0_DTDBS_DEFVAL -#undef DDR_PHY_DTCR0_DTDBS_SHIFT -#undef DDR_PHY_DTCR0_DTDBS_MASK -#define DDR_PHY_DTCR0_DTDBS_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTDBS_SHIFT 16 -#define DDR_PHY_DTCR0_DTDBS_MASK 0x000F0000U - -/*Data Training read DBI deskewing configuration*/ -#undef DDR_PHY_DTCR0_DTRDBITR_DEFVAL -#undef DDR_PHY_DTCR0_DTRDBITR_SHIFT -#undef DDR_PHY_DTCR0_DTRDBITR_MASK -#define DDR_PHY_DTCR0_DTRDBITR_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTRDBITR_SHIFT 14 -#define DDR_PHY_DTCR0_DTRDBITR_MASK 0x0000C000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTCR0_RESERVED_13_DEFVAL -#undef DDR_PHY_DTCR0_RESERVED_13_SHIFT -#undef DDR_PHY_DTCR0_RESERVED_13_MASK -#define DDR_PHY_DTCR0_RESERVED_13_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_RESERVED_13_SHIFT 13 -#define DDR_PHY_DTCR0_RESERVED_13_MASK 0x00002000U - -/*Data Training Write Bit Deskew Data Mask*/ -#undef DDR_PHY_DTCR0_DTWBDDM_DEFVAL -#undef DDR_PHY_DTCR0_DTWBDDM_SHIFT -#undef DDR_PHY_DTCR0_DTWBDDM_MASK -#define DDR_PHY_DTCR0_DTWBDDM_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTWBDDM_SHIFT 12 -#define DDR_PHY_DTCR0_DTWBDDM_MASK 0x00001000U - -/*Refreshes Issued During Entry to Training*/ -#undef DDR_PHY_DTCR0_RFSHEN_DEFVAL -#undef DDR_PHY_DTCR0_RFSHEN_SHIFT -#undef DDR_PHY_DTCR0_RFSHEN_MASK -#define DDR_PHY_DTCR0_RFSHEN_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_RFSHEN_SHIFT 8 -#define DDR_PHY_DTCR0_RFSHEN_MASK 0x00000F00U - -/*Data Training Compare Data*/ -#undef DDR_PHY_DTCR0_DTCMPD_DEFVAL -#undef DDR_PHY_DTCR0_DTCMPD_SHIFT -#undef DDR_PHY_DTCR0_DTCMPD_MASK -#define DDR_PHY_DTCR0_DTCMPD_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTCMPD_SHIFT 7 -#define DDR_PHY_DTCR0_DTCMPD_MASK 0x00000080U - -/*Data Training Using MPR*/ -#undef DDR_PHY_DTCR0_DTMPR_DEFVAL -#undef DDR_PHY_DTCR0_DTMPR_SHIFT -#undef DDR_PHY_DTCR0_DTMPR_MASK -#define DDR_PHY_DTCR0_DTMPR_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTMPR_SHIFT 6 -#define DDR_PHY_DTCR0_DTMPR_MASK 0x00000040U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTCR0_RESERVED_5_4_DEFVAL -#undef DDR_PHY_DTCR0_RESERVED_5_4_SHIFT -#undef DDR_PHY_DTCR0_RESERVED_5_4_MASK -#define DDR_PHY_DTCR0_RESERVED_5_4_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_RESERVED_5_4_SHIFT 4 -#define DDR_PHY_DTCR0_RESERVED_5_4_MASK 0x00000030U - -/*Data Training Repeat Number*/ -#undef DDR_PHY_DTCR0_DTRPTN_DEFVAL -#undef DDR_PHY_DTCR0_DTRPTN_SHIFT -#undef DDR_PHY_DTCR0_DTRPTN_MASK -#define DDR_PHY_DTCR0_DTRPTN_DEFVAL 0x800091C7 -#define DDR_PHY_DTCR0_DTRPTN_SHIFT 0 -#define DDR_PHY_DTCR0_DTRPTN_MASK 0x0000000FU - -/*Rank Enable.*/ -#undef DDR_PHY_DTCR1_RANKEN_RSVD_DEFVAL -#undef DDR_PHY_DTCR1_RANKEN_RSVD_SHIFT -#undef DDR_PHY_DTCR1_RANKEN_RSVD_MASK -#define DDR_PHY_DTCR1_RANKEN_RSVD_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_RANKEN_RSVD_SHIFT 18 -#define DDR_PHY_DTCR1_RANKEN_RSVD_MASK 0xFFFC0000U - -/*Rank Enable.*/ -#undef DDR_PHY_DTCR1_RANKEN_DEFVAL -#undef DDR_PHY_DTCR1_RANKEN_SHIFT -#undef DDR_PHY_DTCR1_RANKEN_MASK -#define DDR_PHY_DTCR1_RANKEN_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_RANKEN_SHIFT 16 -#define DDR_PHY_DTCR1_RANKEN_MASK 0x00030000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTCR1_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DTCR1_RESERVED_15_14_SHIFT -#undef DDR_PHY_DTCR1_RESERVED_15_14_MASK -#define DDR_PHY_DTCR1_RESERVED_15_14_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DTCR1_RESERVED_15_14_MASK 0x0000C000U - -/*Data Training Rank*/ -#undef DDR_PHY_DTCR1_DTRANK_DEFVAL -#undef DDR_PHY_DTCR1_DTRANK_SHIFT -#undef DDR_PHY_DTCR1_DTRANK_MASK -#define DDR_PHY_DTCR1_DTRANK_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_DTRANK_SHIFT 12 -#define DDR_PHY_DTCR1_DTRANK_MASK 0x00003000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTCR1_RESERVED_11_DEFVAL -#undef DDR_PHY_DTCR1_RESERVED_11_SHIFT -#undef DDR_PHY_DTCR1_RESERVED_11_MASK -#define DDR_PHY_DTCR1_RESERVED_11_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_RESERVED_11_SHIFT 11 -#define DDR_PHY_DTCR1_RESERVED_11_MASK 0x00000800U - -/*Read Leveling Gate Sampling Difference*/ -#undef DDR_PHY_DTCR1_RDLVLGDIFF_DEFVAL -#undef DDR_PHY_DTCR1_RDLVLGDIFF_SHIFT -#undef DDR_PHY_DTCR1_RDLVLGDIFF_MASK -#define DDR_PHY_DTCR1_RDLVLGDIFF_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_RDLVLGDIFF_SHIFT 8 -#define DDR_PHY_DTCR1_RDLVLGDIFF_MASK 0x00000700U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTCR1_RESERVED_7_DEFVAL -#undef DDR_PHY_DTCR1_RESERVED_7_SHIFT -#undef DDR_PHY_DTCR1_RESERVED_7_MASK -#define DDR_PHY_DTCR1_RESERVED_7_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_RESERVED_7_SHIFT 7 -#define DDR_PHY_DTCR1_RESERVED_7_MASK 0x00000080U - -/*Read Leveling Gate Shift*/ -#undef DDR_PHY_DTCR1_RDLVLGS_DEFVAL -#undef DDR_PHY_DTCR1_RDLVLGS_SHIFT -#undef DDR_PHY_DTCR1_RDLVLGS_MASK -#define DDR_PHY_DTCR1_RDLVLGS_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_RDLVLGS_SHIFT 4 -#define DDR_PHY_DTCR1_RDLVLGS_MASK 0x00000070U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DTCR1_RESERVED_3_DEFVAL -#undef DDR_PHY_DTCR1_RESERVED_3_SHIFT -#undef DDR_PHY_DTCR1_RESERVED_3_MASK -#define DDR_PHY_DTCR1_RESERVED_3_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_RESERVED_3_SHIFT 3 -#define DDR_PHY_DTCR1_RESERVED_3_MASK 0x00000008U - -/*Read Preamble Training enable*/ -#undef DDR_PHY_DTCR1_RDPRMVL_TRN_DEFVAL -#undef DDR_PHY_DTCR1_RDPRMVL_TRN_SHIFT -#undef DDR_PHY_DTCR1_RDPRMVL_TRN_MASK -#define DDR_PHY_DTCR1_RDPRMVL_TRN_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_RDPRMVL_TRN_SHIFT 2 -#define DDR_PHY_DTCR1_RDPRMVL_TRN_MASK 0x00000004U - -/*Read Leveling Enable*/ -#undef DDR_PHY_DTCR1_RDLVLEN_DEFVAL -#undef DDR_PHY_DTCR1_RDLVLEN_SHIFT -#undef DDR_PHY_DTCR1_RDLVLEN_MASK -#define DDR_PHY_DTCR1_RDLVLEN_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_RDLVLEN_SHIFT 1 -#define DDR_PHY_DTCR1_RDLVLEN_MASK 0x00000002U - -/*Basic Gate Training Enable*/ -#undef DDR_PHY_DTCR1_BSTEN_DEFVAL -#undef DDR_PHY_DTCR1_BSTEN_SHIFT -#undef DDR_PHY_DTCR1_BSTEN_MASK -#define DDR_PHY_DTCR1_BSTEN_DEFVAL 0x00030237 -#define DDR_PHY_DTCR1_BSTEN_SHIFT 0 -#define DDR_PHY_DTCR1_BSTEN_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_CATR0_RESERVED_31_21_DEFVAL -#undef DDR_PHY_CATR0_RESERVED_31_21_SHIFT -#undef DDR_PHY_CATR0_RESERVED_31_21_MASK -#define DDR_PHY_CATR0_RESERVED_31_21_DEFVAL 0x00141054 -#define DDR_PHY_CATR0_RESERVED_31_21_SHIFT 21 -#define DDR_PHY_CATR0_RESERVED_31_21_MASK 0xFFE00000U - -/*Minimum time (in terms of number of dram clocks) between two consectuve CA calibration command*/ -#undef DDR_PHY_CATR0_CACD_DEFVAL -#undef DDR_PHY_CATR0_CACD_SHIFT -#undef DDR_PHY_CATR0_CACD_MASK -#define DDR_PHY_CATR0_CACD_DEFVAL 0x00141054 -#define DDR_PHY_CATR0_CACD_SHIFT 16 -#define DDR_PHY_CATR0_CACD_MASK 0x001F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_CATR0_RESERVED_15_13_DEFVAL -#undef DDR_PHY_CATR0_RESERVED_15_13_SHIFT -#undef DDR_PHY_CATR0_RESERVED_15_13_MASK -#define DDR_PHY_CATR0_RESERVED_15_13_DEFVAL 0x00141054 -#define DDR_PHY_CATR0_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_CATR0_RESERVED_15_13_MASK 0x0000E000U - -/*Minimum time (in terms of number of dram clocks) PUB should wait before sampling the CA response after Calibration command ha - been sent to the memory*/ -#undef DDR_PHY_CATR0_CAADR_DEFVAL -#undef DDR_PHY_CATR0_CAADR_SHIFT -#undef DDR_PHY_CATR0_CAADR_MASK -#define DDR_PHY_CATR0_CAADR_DEFVAL 0x00141054 -#define DDR_PHY_CATR0_CAADR_SHIFT 8 -#define DDR_PHY_CATR0_CAADR_MASK 0x00001F00U - -/*CA_1 Response Byte Lane 1*/ -#undef DDR_PHY_CATR0_CA1BYTE1_DEFVAL -#undef DDR_PHY_CATR0_CA1BYTE1_SHIFT -#undef DDR_PHY_CATR0_CA1BYTE1_MASK -#define DDR_PHY_CATR0_CA1BYTE1_DEFVAL 0x00141054 -#define DDR_PHY_CATR0_CA1BYTE1_SHIFT 4 -#define DDR_PHY_CATR0_CA1BYTE1_MASK 0x000000F0U - -/*CA_1 Response Byte Lane 0*/ -#undef DDR_PHY_CATR0_CA1BYTE0_DEFVAL -#undef DDR_PHY_CATR0_CA1BYTE0_SHIFT -#undef DDR_PHY_CATR0_CA1BYTE0_MASK -#define DDR_PHY_CATR0_CA1BYTE0_DEFVAL 0x00141054 -#define DDR_PHY_CATR0_CA1BYTE0_SHIFT 0 -#define DDR_PHY_CATR0_CA1BYTE0_MASK 0x0000000FU - -/*LFSR seed for pseudo-random BIST patterns*/ -#undef DDR_PHY_BISTLSR_SEED_DEFVAL -#undef DDR_PHY_BISTLSR_SEED_SHIFT -#undef DDR_PHY_BISTLSR_SEED_MASK -#define DDR_PHY_BISTLSR_SEED_DEFVAL -#define DDR_PHY_BISTLSR_SEED_SHIFT 0 -#define DDR_PHY_BISTLSR_SEED_MASK 0xFFFFFFFFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_RIOCR5_RESERVED_31_16_DEFVAL -#undef DDR_PHY_RIOCR5_RESERVED_31_16_SHIFT -#undef DDR_PHY_RIOCR5_RESERVED_31_16_MASK -#define DDR_PHY_RIOCR5_RESERVED_31_16_DEFVAL 0x00000005 -#define DDR_PHY_RIOCR5_RESERVED_31_16_SHIFT 16 -#define DDR_PHY_RIOCR5_RESERVED_31_16_MASK 0xFFFF0000U - -/*Reserved. Return zeros on reads.*/ -#undef DDR_PHY_RIOCR5_ODTOEMODE_RSVD_DEFVAL -#undef DDR_PHY_RIOCR5_ODTOEMODE_RSVD_SHIFT -#undef DDR_PHY_RIOCR5_ODTOEMODE_RSVD_MASK -#define DDR_PHY_RIOCR5_ODTOEMODE_RSVD_DEFVAL 0x00000005 -#define DDR_PHY_RIOCR5_ODTOEMODE_RSVD_SHIFT 4 -#define DDR_PHY_RIOCR5_ODTOEMODE_RSVD_MASK 0x0000FFF0U - -/*SDRAM On-die Termination Output Enable (OE) Mode Selection.*/ -#undef DDR_PHY_RIOCR5_ODTOEMODE_DEFVAL -#undef DDR_PHY_RIOCR5_ODTOEMODE_SHIFT -#undef DDR_PHY_RIOCR5_ODTOEMODE_MASK -#define DDR_PHY_RIOCR5_ODTOEMODE_DEFVAL 0x00000005 -#define DDR_PHY_RIOCR5_ODTOEMODE_SHIFT 0 -#define DDR_PHY_RIOCR5_ODTOEMODE_MASK 0x0000000FU - -/*Address/Command Slew Rate (D3F I/O Only)*/ -#undef DDR_PHY_ACIOCR0_ACSR_DEFVAL -#undef DDR_PHY_ACIOCR0_ACSR_SHIFT -#undef DDR_PHY_ACIOCR0_ACSR_MASK -#define DDR_PHY_ACIOCR0_ACSR_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_ACSR_SHIFT 30 -#define DDR_PHY_ACIOCR0_ACSR_MASK 0xC0000000U - -/*SDRAM Reset I/O Mode*/ -#undef DDR_PHY_ACIOCR0_RSTIOM_DEFVAL -#undef DDR_PHY_ACIOCR0_RSTIOM_SHIFT -#undef DDR_PHY_ACIOCR0_RSTIOM_MASK -#define DDR_PHY_ACIOCR0_RSTIOM_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_RSTIOM_SHIFT 29 -#define DDR_PHY_ACIOCR0_RSTIOM_MASK 0x20000000U - -/*SDRAM Reset Power Down Receiver*/ -#undef DDR_PHY_ACIOCR0_RSTPDR_DEFVAL -#undef DDR_PHY_ACIOCR0_RSTPDR_SHIFT -#undef DDR_PHY_ACIOCR0_RSTPDR_MASK -#define DDR_PHY_ACIOCR0_RSTPDR_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_RSTPDR_SHIFT 28 -#define DDR_PHY_ACIOCR0_RSTPDR_MASK 0x10000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACIOCR0_RESERVED_27_DEFVAL -#undef DDR_PHY_ACIOCR0_RESERVED_27_SHIFT -#undef DDR_PHY_ACIOCR0_RESERVED_27_MASK -#define DDR_PHY_ACIOCR0_RESERVED_27_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_RESERVED_27_SHIFT 27 -#define DDR_PHY_ACIOCR0_RESERVED_27_MASK 0x08000000U - -/*SDRAM Reset On-Die Termination*/ -#undef DDR_PHY_ACIOCR0_RSTODT_DEFVAL -#undef DDR_PHY_ACIOCR0_RSTODT_SHIFT -#undef DDR_PHY_ACIOCR0_RSTODT_MASK -#define DDR_PHY_ACIOCR0_RSTODT_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_RSTODT_SHIFT 26 -#define DDR_PHY_ACIOCR0_RSTODT_MASK 0x04000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACIOCR0_RESERVED_25_10_DEFVAL -#undef DDR_PHY_ACIOCR0_RESERVED_25_10_SHIFT -#undef DDR_PHY_ACIOCR0_RESERVED_25_10_MASK -#define DDR_PHY_ACIOCR0_RESERVED_25_10_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_RESERVED_25_10_SHIFT 10 -#define DDR_PHY_ACIOCR0_RESERVED_25_10_MASK 0x03FFFC00U - -/*CK Duty Cycle Correction*/ -#undef DDR_PHY_ACIOCR0_CKDCC_DEFVAL -#undef DDR_PHY_ACIOCR0_CKDCC_SHIFT -#undef DDR_PHY_ACIOCR0_CKDCC_MASK -#define DDR_PHY_ACIOCR0_CKDCC_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_CKDCC_SHIFT 6 -#define DDR_PHY_ACIOCR0_CKDCC_MASK 0x000003C0U - -/*AC Power Down Receiver Mode*/ -#undef DDR_PHY_ACIOCR0_ACPDRMODE_DEFVAL -#undef DDR_PHY_ACIOCR0_ACPDRMODE_SHIFT -#undef DDR_PHY_ACIOCR0_ACPDRMODE_MASK -#define DDR_PHY_ACIOCR0_ACPDRMODE_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_ACPDRMODE_SHIFT 4 -#define DDR_PHY_ACIOCR0_ACPDRMODE_MASK 0x00000030U - -/*AC On-die Termination Mode*/ -#undef DDR_PHY_ACIOCR0_ACODTMODE_DEFVAL -#undef DDR_PHY_ACIOCR0_ACODTMODE_SHIFT -#undef DDR_PHY_ACIOCR0_ACODTMODE_MASK -#define DDR_PHY_ACIOCR0_ACODTMODE_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_ACODTMODE_SHIFT 2 -#define DDR_PHY_ACIOCR0_ACODTMODE_MASK 0x0000000CU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACIOCR0_RESERVED_1_DEFVAL -#undef DDR_PHY_ACIOCR0_RESERVED_1_SHIFT -#undef DDR_PHY_ACIOCR0_RESERVED_1_MASK -#define DDR_PHY_ACIOCR0_RESERVED_1_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_RESERVED_1_SHIFT 1 -#define DDR_PHY_ACIOCR0_RESERVED_1_MASK 0x00000002U - -/*Control delayed or non-delayed clock to CS_N/ODT?CKE AC slices.*/ -#undef DDR_PHY_ACIOCR0_ACRANKCLKSEL_DEFVAL -#undef DDR_PHY_ACIOCR0_ACRANKCLKSEL_SHIFT -#undef DDR_PHY_ACIOCR0_ACRANKCLKSEL_MASK -#define DDR_PHY_ACIOCR0_ACRANKCLKSEL_DEFVAL 0x30000000 -#define DDR_PHY_ACIOCR0_ACRANKCLKSEL_SHIFT 0 -#define DDR_PHY_ACIOCR0_ACRANKCLKSEL_MASK 0x00000001U - -/*Clock gating for glue logic inside CLKGEN and glue logic inside CONTROL slice*/ -#undef DDR_PHY_ACIOCR2_CLKGENCLKGATE_DEFVAL -#undef DDR_PHY_ACIOCR2_CLKGENCLKGATE_SHIFT -#undef DDR_PHY_ACIOCR2_CLKGENCLKGATE_MASK -#define DDR_PHY_ACIOCR2_CLKGENCLKGATE_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR2_CLKGENCLKGATE_SHIFT 31 -#define DDR_PHY_ACIOCR2_CLKGENCLKGATE_MASK 0x80000000U - -/*Clock gating for Output Enable D slices [0]*/ -#undef DDR_PHY_ACIOCR2_ACOECLKGATE0_DEFVAL -#undef DDR_PHY_ACIOCR2_ACOECLKGATE0_SHIFT -#undef DDR_PHY_ACIOCR2_ACOECLKGATE0_MASK -#define DDR_PHY_ACIOCR2_ACOECLKGATE0_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR2_ACOECLKGATE0_SHIFT 30 -#define DDR_PHY_ACIOCR2_ACOECLKGATE0_MASK 0x40000000U - -/*Clock gating for Power Down Receiver D slices [0]*/ -#undef DDR_PHY_ACIOCR2_ACPDRCLKGATE0_DEFVAL -#undef DDR_PHY_ACIOCR2_ACPDRCLKGATE0_SHIFT -#undef DDR_PHY_ACIOCR2_ACPDRCLKGATE0_MASK -#define DDR_PHY_ACIOCR2_ACPDRCLKGATE0_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR2_ACPDRCLKGATE0_SHIFT 29 -#define DDR_PHY_ACIOCR2_ACPDRCLKGATE0_MASK 0x20000000U - -/*Clock gating for Termination Enable D slices [0]*/ -#undef DDR_PHY_ACIOCR2_ACTECLKGATE0_DEFVAL -#undef DDR_PHY_ACIOCR2_ACTECLKGATE0_SHIFT -#undef DDR_PHY_ACIOCR2_ACTECLKGATE0_MASK -#define DDR_PHY_ACIOCR2_ACTECLKGATE0_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR2_ACTECLKGATE0_SHIFT 28 -#define DDR_PHY_ACIOCR2_ACTECLKGATE0_MASK 0x10000000U - -/*Clock gating for CK# D slices [1:0]*/ -#undef DDR_PHY_ACIOCR2_CKNCLKGATE0_DEFVAL -#undef DDR_PHY_ACIOCR2_CKNCLKGATE0_SHIFT -#undef DDR_PHY_ACIOCR2_CKNCLKGATE0_MASK -#define DDR_PHY_ACIOCR2_CKNCLKGATE0_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR2_CKNCLKGATE0_SHIFT 26 -#define DDR_PHY_ACIOCR2_CKNCLKGATE0_MASK 0x0C000000U - -/*Clock gating for CK D slices [1:0]*/ -#undef DDR_PHY_ACIOCR2_CKCLKGATE0_DEFVAL -#undef DDR_PHY_ACIOCR2_CKCLKGATE0_SHIFT -#undef DDR_PHY_ACIOCR2_CKCLKGATE0_MASK -#define DDR_PHY_ACIOCR2_CKCLKGATE0_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR2_CKCLKGATE0_SHIFT 24 -#define DDR_PHY_ACIOCR2_CKCLKGATE0_MASK 0x03000000U - -/*Clock gating for AC D slices [23:0]*/ -#undef DDR_PHY_ACIOCR2_ACCLKGATE0_DEFVAL -#undef DDR_PHY_ACIOCR2_ACCLKGATE0_SHIFT -#undef DDR_PHY_ACIOCR2_ACCLKGATE0_MASK -#define DDR_PHY_ACIOCR2_ACCLKGATE0_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR2_ACCLKGATE0_SHIFT 0 -#define DDR_PHY_ACIOCR2_ACCLKGATE0_MASK 0x00FFFFFFU - -/*SDRAM Parity Output Enable (OE) Mode Selection*/ -#undef DDR_PHY_ACIOCR3_PAROEMODE_DEFVAL -#undef DDR_PHY_ACIOCR3_PAROEMODE_SHIFT -#undef DDR_PHY_ACIOCR3_PAROEMODE_MASK -#define DDR_PHY_ACIOCR3_PAROEMODE_DEFVAL 0x00000005 -#define DDR_PHY_ACIOCR3_PAROEMODE_SHIFT 30 -#define DDR_PHY_ACIOCR3_PAROEMODE_MASK 0xC0000000U - -/*SDRAM Bank Group Output Enable (OE) Mode Selection*/ -#undef DDR_PHY_ACIOCR3_BGOEMODE_DEFVAL -#undef DDR_PHY_ACIOCR3_BGOEMODE_SHIFT -#undef DDR_PHY_ACIOCR3_BGOEMODE_MASK -#define DDR_PHY_ACIOCR3_BGOEMODE_DEFVAL 0x00000005 -#define DDR_PHY_ACIOCR3_BGOEMODE_SHIFT 26 -#define DDR_PHY_ACIOCR3_BGOEMODE_MASK 0x3C000000U - -/*SDRAM Bank Address Output Enable (OE) Mode Selection*/ -#undef DDR_PHY_ACIOCR3_BAOEMODE_DEFVAL -#undef DDR_PHY_ACIOCR3_BAOEMODE_SHIFT -#undef DDR_PHY_ACIOCR3_BAOEMODE_MASK -#define DDR_PHY_ACIOCR3_BAOEMODE_DEFVAL 0x00000005 -#define DDR_PHY_ACIOCR3_BAOEMODE_SHIFT 22 -#define DDR_PHY_ACIOCR3_BAOEMODE_MASK 0x03C00000U - -/*SDRAM A[17] Output Enable (OE) Mode Selection*/ -#undef DDR_PHY_ACIOCR3_A17OEMODE_DEFVAL -#undef DDR_PHY_ACIOCR3_A17OEMODE_SHIFT -#undef DDR_PHY_ACIOCR3_A17OEMODE_MASK -#define DDR_PHY_ACIOCR3_A17OEMODE_DEFVAL 0x00000005 -#define DDR_PHY_ACIOCR3_A17OEMODE_SHIFT 20 -#define DDR_PHY_ACIOCR3_A17OEMODE_MASK 0x00300000U - -/*SDRAM A[16] / RAS_n Output Enable (OE) Mode Selection*/ -#undef DDR_PHY_ACIOCR3_A16OEMODE_DEFVAL -#undef DDR_PHY_ACIOCR3_A16OEMODE_SHIFT -#undef DDR_PHY_ACIOCR3_A16OEMODE_MASK -#define DDR_PHY_ACIOCR3_A16OEMODE_DEFVAL 0x00000005 -#define DDR_PHY_ACIOCR3_A16OEMODE_SHIFT 18 -#define DDR_PHY_ACIOCR3_A16OEMODE_MASK 0x000C0000U - -/*SDRAM ACT_n Output Enable (OE) Mode Selection (DDR4 only)*/ -#undef DDR_PHY_ACIOCR3_ACTOEMODE_DEFVAL -#undef DDR_PHY_ACIOCR3_ACTOEMODE_SHIFT -#undef DDR_PHY_ACIOCR3_ACTOEMODE_MASK -#define DDR_PHY_ACIOCR3_ACTOEMODE_DEFVAL 0x00000005 -#define DDR_PHY_ACIOCR3_ACTOEMODE_SHIFT 16 -#define DDR_PHY_ACIOCR3_ACTOEMODE_MASK 0x00030000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACIOCR3_RESERVED_15_8_DEFVAL -#undef DDR_PHY_ACIOCR3_RESERVED_15_8_SHIFT -#undef DDR_PHY_ACIOCR3_RESERVED_15_8_MASK -#define DDR_PHY_ACIOCR3_RESERVED_15_8_DEFVAL 0x00000005 -#define DDR_PHY_ACIOCR3_RESERVED_15_8_SHIFT 8 -#define DDR_PHY_ACIOCR3_RESERVED_15_8_MASK 0x0000FF00U - -/*Reserved. Return zeros on reads.*/ -#undef DDR_PHY_ACIOCR3_CKOEMODE_RSVD_DEFVAL -#undef DDR_PHY_ACIOCR3_CKOEMODE_RSVD_SHIFT -#undef DDR_PHY_ACIOCR3_CKOEMODE_RSVD_MASK -#define DDR_PHY_ACIOCR3_CKOEMODE_RSVD_DEFVAL 0x00000005 -#define DDR_PHY_ACIOCR3_CKOEMODE_RSVD_SHIFT 4 -#define DDR_PHY_ACIOCR3_CKOEMODE_RSVD_MASK 0x000000F0U - -/*SDRAM CK Output Enable (OE) Mode Selection.*/ -#undef DDR_PHY_ACIOCR3_CKOEMODE_DEFVAL -#undef DDR_PHY_ACIOCR3_CKOEMODE_SHIFT -#undef DDR_PHY_ACIOCR3_CKOEMODE_MASK -#define DDR_PHY_ACIOCR3_CKOEMODE_DEFVAL 0x00000005 -#define DDR_PHY_ACIOCR3_CKOEMODE_SHIFT 0 -#define DDR_PHY_ACIOCR3_CKOEMODE_MASK 0x0000000FU - -/*Clock gating for AC LB slices and loopback read valid slices*/ -#undef DDR_PHY_ACIOCR4_LBCLKGATE_DEFVAL -#undef DDR_PHY_ACIOCR4_LBCLKGATE_SHIFT -#undef DDR_PHY_ACIOCR4_LBCLKGATE_MASK -#define DDR_PHY_ACIOCR4_LBCLKGATE_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR4_LBCLKGATE_SHIFT 31 -#define DDR_PHY_ACIOCR4_LBCLKGATE_MASK 0x80000000U - -/*Clock gating for Output Enable D slices [1]*/ -#undef DDR_PHY_ACIOCR4_ACOECLKGATE1_DEFVAL -#undef DDR_PHY_ACIOCR4_ACOECLKGATE1_SHIFT -#undef DDR_PHY_ACIOCR4_ACOECLKGATE1_MASK -#define DDR_PHY_ACIOCR4_ACOECLKGATE1_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR4_ACOECLKGATE1_SHIFT 30 -#define DDR_PHY_ACIOCR4_ACOECLKGATE1_MASK 0x40000000U - -/*Clock gating for Power Down Receiver D slices [1]*/ -#undef DDR_PHY_ACIOCR4_ACPDRCLKGATE1_DEFVAL -#undef DDR_PHY_ACIOCR4_ACPDRCLKGATE1_SHIFT -#undef DDR_PHY_ACIOCR4_ACPDRCLKGATE1_MASK -#define DDR_PHY_ACIOCR4_ACPDRCLKGATE1_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR4_ACPDRCLKGATE1_SHIFT 29 -#define DDR_PHY_ACIOCR4_ACPDRCLKGATE1_MASK 0x20000000U - -/*Clock gating for Termination Enable D slices [1]*/ -#undef DDR_PHY_ACIOCR4_ACTECLKGATE1_DEFVAL -#undef DDR_PHY_ACIOCR4_ACTECLKGATE1_SHIFT -#undef DDR_PHY_ACIOCR4_ACTECLKGATE1_MASK -#define DDR_PHY_ACIOCR4_ACTECLKGATE1_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR4_ACTECLKGATE1_SHIFT 28 -#define DDR_PHY_ACIOCR4_ACTECLKGATE1_MASK 0x10000000U - -/*Clock gating for CK# D slices [3:2]*/ -#undef DDR_PHY_ACIOCR4_CKNCLKGATE1_DEFVAL -#undef DDR_PHY_ACIOCR4_CKNCLKGATE1_SHIFT -#undef DDR_PHY_ACIOCR4_CKNCLKGATE1_MASK -#define DDR_PHY_ACIOCR4_CKNCLKGATE1_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR4_CKNCLKGATE1_SHIFT 26 -#define DDR_PHY_ACIOCR4_CKNCLKGATE1_MASK 0x0C000000U - -/*Clock gating for CK D slices [3:2]*/ -#undef DDR_PHY_ACIOCR4_CKCLKGATE1_DEFVAL -#undef DDR_PHY_ACIOCR4_CKCLKGATE1_SHIFT -#undef DDR_PHY_ACIOCR4_CKCLKGATE1_MASK -#define DDR_PHY_ACIOCR4_CKCLKGATE1_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR4_CKCLKGATE1_SHIFT 24 -#define DDR_PHY_ACIOCR4_CKCLKGATE1_MASK 0x03000000U - -/*Clock gating for AC D slices [47:24]*/ -#undef DDR_PHY_ACIOCR4_ACCLKGATE1_DEFVAL -#undef DDR_PHY_ACIOCR4_ACCLKGATE1_SHIFT -#undef DDR_PHY_ACIOCR4_ACCLKGATE1_MASK -#define DDR_PHY_ACIOCR4_ACCLKGATE1_DEFVAL 0x00000000 -#define DDR_PHY_ACIOCR4_ACCLKGATE1_SHIFT 0 -#define DDR_PHY_ACIOCR4_ACCLKGATE1_MASK 0x00FFFFFFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_IOVCR0_RESERVED_31_29_DEFVAL -#undef DDR_PHY_IOVCR0_RESERVED_31_29_SHIFT -#undef DDR_PHY_IOVCR0_RESERVED_31_29_MASK -#define DDR_PHY_IOVCR0_RESERVED_31_29_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_IOVCR0_RESERVED_31_29_MASK 0xE0000000U - -/*Address/command lane VREF Pad Enable*/ -#undef DDR_PHY_IOVCR0_ACREFPEN_DEFVAL -#undef DDR_PHY_IOVCR0_ACREFPEN_SHIFT -#undef DDR_PHY_IOVCR0_ACREFPEN_MASK -#define DDR_PHY_IOVCR0_ACREFPEN_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_ACREFPEN_SHIFT 28 -#define DDR_PHY_IOVCR0_ACREFPEN_MASK 0x10000000U - -/*Address/command lane Internal VREF Enable*/ -#undef DDR_PHY_IOVCR0_ACREFEEN_DEFVAL -#undef DDR_PHY_IOVCR0_ACREFEEN_SHIFT -#undef DDR_PHY_IOVCR0_ACREFEEN_MASK -#define DDR_PHY_IOVCR0_ACREFEEN_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_ACREFEEN_SHIFT 26 -#define DDR_PHY_IOVCR0_ACREFEEN_MASK 0x0C000000U - -/*Address/command lane Single-End VREF Enable*/ -#undef DDR_PHY_IOVCR0_ACREFSEN_DEFVAL -#undef DDR_PHY_IOVCR0_ACREFSEN_SHIFT -#undef DDR_PHY_IOVCR0_ACREFSEN_MASK -#define DDR_PHY_IOVCR0_ACREFSEN_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_ACREFSEN_SHIFT 25 -#define DDR_PHY_IOVCR0_ACREFSEN_MASK 0x02000000U - -/*Address/command lane Internal VREF Enable*/ -#undef DDR_PHY_IOVCR0_ACREFIEN_DEFVAL -#undef DDR_PHY_IOVCR0_ACREFIEN_SHIFT -#undef DDR_PHY_IOVCR0_ACREFIEN_MASK -#define DDR_PHY_IOVCR0_ACREFIEN_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_ACREFIEN_SHIFT 24 -#define DDR_PHY_IOVCR0_ACREFIEN_MASK 0x01000000U - -/*External VREF generato REFSEL range select*/ -#undef DDR_PHY_IOVCR0_ACREFESELRANGE_DEFVAL -#undef DDR_PHY_IOVCR0_ACREFESELRANGE_SHIFT -#undef DDR_PHY_IOVCR0_ACREFESELRANGE_MASK -#define DDR_PHY_IOVCR0_ACREFESELRANGE_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_ACREFESELRANGE_SHIFT 23 -#define DDR_PHY_IOVCR0_ACREFESELRANGE_MASK 0x00800000U - -/*Address/command lane External VREF Select*/ -#undef DDR_PHY_IOVCR0_ACREFESEL_DEFVAL -#undef DDR_PHY_IOVCR0_ACREFESEL_SHIFT -#undef DDR_PHY_IOVCR0_ACREFESEL_MASK -#define DDR_PHY_IOVCR0_ACREFESEL_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_ACREFESEL_SHIFT 16 -#define DDR_PHY_IOVCR0_ACREFESEL_MASK 0x007F0000U - -/*Single ended VREF generator REFSEL range select*/ -#undef DDR_PHY_IOVCR0_ACREFSSELRANGE_DEFVAL -#undef DDR_PHY_IOVCR0_ACREFSSELRANGE_SHIFT -#undef DDR_PHY_IOVCR0_ACREFSSELRANGE_MASK -#define DDR_PHY_IOVCR0_ACREFSSELRANGE_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_ACREFSSELRANGE_SHIFT 15 -#define DDR_PHY_IOVCR0_ACREFSSELRANGE_MASK 0x00008000U - -/*Address/command lane Single-End VREF Select*/ -#undef DDR_PHY_IOVCR0_ACREFSSEL_DEFVAL -#undef DDR_PHY_IOVCR0_ACREFSSEL_SHIFT -#undef DDR_PHY_IOVCR0_ACREFSSEL_MASK -#define DDR_PHY_IOVCR0_ACREFSSEL_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_ACREFSSEL_SHIFT 8 -#define DDR_PHY_IOVCR0_ACREFSSEL_MASK 0x00007F00U - -/*Internal VREF generator REFSEL ragne select*/ -#undef DDR_PHY_IOVCR0_ACVREFISELRANGE_DEFVAL -#undef DDR_PHY_IOVCR0_ACVREFISELRANGE_SHIFT -#undef DDR_PHY_IOVCR0_ACVREFISELRANGE_MASK -#define DDR_PHY_IOVCR0_ACVREFISELRANGE_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_ACVREFISELRANGE_SHIFT 7 -#define DDR_PHY_IOVCR0_ACVREFISELRANGE_MASK 0x00000080U - -/*REFSEL Control for internal AC IOs*/ -#undef DDR_PHY_IOVCR0_ACVREFISEL_DEFVAL -#undef DDR_PHY_IOVCR0_ACVREFISEL_SHIFT -#undef DDR_PHY_IOVCR0_ACVREFISEL_MASK -#define DDR_PHY_IOVCR0_ACVREFISEL_DEFVAL 0x0F000000 -#define DDR_PHY_IOVCR0_ACVREFISEL_SHIFT 0 -#define DDR_PHY_IOVCR0_ACVREFISEL_MASK 0x0000007FU - -/*Number of ctl_clk required to meet (> 150ns) timing requirements during DRAM DQ VREF training*/ -#undef DDR_PHY_VTCR0_TVREF_DEFVAL -#undef DDR_PHY_VTCR0_TVREF_SHIFT -#undef DDR_PHY_VTCR0_TVREF_MASK -#define DDR_PHY_VTCR0_TVREF_DEFVAL 0x70032019 -#define DDR_PHY_VTCR0_TVREF_SHIFT 29 -#define DDR_PHY_VTCR0_TVREF_MASK 0xE0000000U - -/*DRM DQ VREF training Enable*/ -#undef DDR_PHY_VTCR0_DVEN_DEFVAL -#undef DDR_PHY_VTCR0_DVEN_SHIFT -#undef DDR_PHY_VTCR0_DVEN_MASK -#define DDR_PHY_VTCR0_DVEN_DEFVAL 0x70032019 -#define DDR_PHY_VTCR0_DVEN_SHIFT 28 -#define DDR_PHY_VTCR0_DVEN_MASK 0x10000000U - -/*Per Device Addressability Enable*/ -#undef DDR_PHY_VTCR0_PDAEN_DEFVAL -#undef DDR_PHY_VTCR0_PDAEN_SHIFT -#undef DDR_PHY_VTCR0_PDAEN_MASK -#define DDR_PHY_VTCR0_PDAEN_DEFVAL 0x70032019 -#define DDR_PHY_VTCR0_PDAEN_SHIFT 27 -#define DDR_PHY_VTCR0_PDAEN_MASK 0x08000000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_VTCR0_RESERVED_26_DEFVAL -#undef DDR_PHY_VTCR0_RESERVED_26_SHIFT -#undef DDR_PHY_VTCR0_RESERVED_26_MASK -#define DDR_PHY_VTCR0_RESERVED_26_DEFVAL 0x70032019 -#define DDR_PHY_VTCR0_RESERVED_26_SHIFT 26 -#define DDR_PHY_VTCR0_RESERVED_26_MASK 0x04000000U - -/*VREF Word Count*/ -#undef DDR_PHY_VTCR0_VWCR_DEFVAL -#undef DDR_PHY_VTCR0_VWCR_SHIFT -#undef DDR_PHY_VTCR0_VWCR_MASK -#define DDR_PHY_VTCR0_VWCR_DEFVAL 0x70032019 -#define DDR_PHY_VTCR0_VWCR_SHIFT 22 -#define DDR_PHY_VTCR0_VWCR_MASK 0x03C00000U - -/*DRAM DQ VREF step size used during DRAM VREF training*/ -#undef DDR_PHY_VTCR0_DVSS_DEFVAL -#undef DDR_PHY_VTCR0_DVSS_SHIFT -#undef DDR_PHY_VTCR0_DVSS_MASK -#define DDR_PHY_VTCR0_DVSS_DEFVAL 0x70032019 -#define DDR_PHY_VTCR0_DVSS_SHIFT 18 -#define DDR_PHY_VTCR0_DVSS_MASK 0x003C0000U - -/*Maximum VREF limit value used during DRAM VREF training*/ -#undef DDR_PHY_VTCR0_DVMAX_DEFVAL -#undef DDR_PHY_VTCR0_DVMAX_SHIFT -#undef DDR_PHY_VTCR0_DVMAX_MASK -#define DDR_PHY_VTCR0_DVMAX_DEFVAL 0x70032019 -#define DDR_PHY_VTCR0_DVMAX_SHIFT 12 -#define DDR_PHY_VTCR0_DVMAX_MASK 0x0003F000U - -/*Minimum VREF limit value used during DRAM VREF training*/ -#undef DDR_PHY_VTCR0_DVMIN_DEFVAL -#undef DDR_PHY_VTCR0_DVMIN_SHIFT -#undef DDR_PHY_VTCR0_DVMIN_MASK -#define DDR_PHY_VTCR0_DVMIN_DEFVAL 0x70032019 -#define DDR_PHY_VTCR0_DVMIN_SHIFT 6 -#define DDR_PHY_VTCR0_DVMIN_MASK 0x00000FC0U - -/*Initial DRAM DQ VREF value used during DRAM VREF training*/ -#undef DDR_PHY_VTCR0_DVINIT_DEFVAL -#undef DDR_PHY_VTCR0_DVINIT_SHIFT -#undef DDR_PHY_VTCR0_DVINIT_MASK -#define DDR_PHY_VTCR0_DVINIT_DEFVAL 0x70032019 -#define DDR_PHY_VTCR0_DVINIT_SHIFT 0 -#define DDR_PHY_VTCR0_DVINIT_MASK 0x0000003FU - -/*Host VREF step size used during VREF training. The register value of N indicates step size of (N+1)*/ -#undef DDR_PHY_VTCR1_HVSS_DEFVAL -#undef DDR_PHY_VTCR1_HVSS_SHIFT -#undef DDR_PHY_VTCR1_HVSS_MASK -#define DDR_PHY_VTCR1_HVSS_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_HVSS_SHIFT 28 -#define DDR_PHY_VTCR1_HVSS_MASK 0xF0000000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_VTCR1_RESERVED_27_DEFVAL -#undef DDR_PHY_VTCR1_RESERVED_27_SHIFT -#undef DDR_PHY_VTCR1_RESERVED_27_MASK -#define DDR_PHY_VTCR1_RESERVED_27_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_RESERVED_27_SHIFT 27 -#define DDR_PHY_VTCR1_RESERVED_27_MASK 0x08000000U - -/*Maximum VREF limit value used during DRAM VREF training.*/ -#undef DDR_PHY_VTCR1_HVMAX_DEFVAL -#undef DDR_PHY_VTCR1_HVMAX_SHIFT -#undef DDR_PHY_VTCR1_HVMAX_MASK -#define DDR_PHY_VTCR1_HVMAX_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_HVMAX_SHIFT 20 -#define DDR_PHY_VTCR1_HVMAX_MASK 0x07F00000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_VTCR1_RESERVED_19_DEFVAL -#undef DDR_PHY_VTCR1_RESERVED_19_SHIFT -#undef DDR_PHY_VTCR1_RESERVED_19_MASK -#define DDR_PHY_VTCR1_RESERVED_19_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_RESERVED_19_SHIFT 19 -#define DDR_PHY_VTCR1_RESERVED_19_MASK 0x00080000U - -/*Minimum VREF limit value used during DRAM VREF training.*/ -#undef DDR_PHY_VTCR1_HVMIN_DEFVAL -#undef DDR_PHY_VTCR1_HVMIN_SHIFT -#undef DDR_PHY_VTCR1_HVMIN_MASK -#define DDR_PHY_VTCR1_HVMIN_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_HVMIN_SHIFT 12 -#define DDR_PHY_VTCR1_HVMIN_MASK 0x0007F000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_VTCR1_RESERVED_11_DEFVAL -#undef DDR_PHY_VTCR1_RESERVED_11_SHIFT -#undef DDR_PHY_VTCR1_RESERVED_11_MASK -#define DDR_PHY_VTCR1_RESERVED_11_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_RESERVED_11_SHIFT 11 -#define DDR_PHY_VTCR1_RESERVED_11_MASK 0x00000800U - -/*Static Host Vref Rank Value*/ -#undef DDR_PHY_VTCR1_SHRNK_DEFVAL -#undef DDR_PHY_VTCR1_SHRNK_SHIFT -#undef DDR_PHY_VTCR1_SHRNK_MASK -#define DDR_PHY_VTCR1_SHRNK_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_SHRNK_SHIFT 9 -#define DDR_PHY_VTCR1_SHRNK_MASK 0x00000600U - -/*Static Host Vref Rank Enable*/ -#undef DDR_PHY_VTCR1_SHREN_DEFVAL -#undef DDR_PHY_VTCR1_SHREN_SHIFT -#undef DDR_PHY_VTCR1_SHREN_MASK -#define DDR_PHY_VTCR1_SHREN_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_SHREN_SHIFT 8 -#define DDR_PHY_VTCR1_SHREN_MASK 0x00000100U - -/*Number of ctl_clk required to meet (> 200ns) VREF Settling timing requirements during Host IO VREF training*/ -#undef DDR_PHY_VTCR1_TVREFIO_DEFVAL -#undef DDR_PHY_VTCR1_TVREFIO_SHIFT -#undef DDR_PHY_VTCR1_TVREFIO_MASK -#define DDR_PHY_VTCR1_TVREFIO_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_TVREFIO_SHIFT 5 -#define DDR_PHY_VTCR1_TVREFIO_MASK 0x000000E0U - -/*Eye LCDL Offset value for VREF training*/ -#undef DDR_PHY_VTCR1_EOFF_DEFVAL -#undef DDR_PHY_VTCR1_EOFF_SHIFT -#undef DDR_PHY_VTCR1_EOFF_MASK -#define DDR_PHY_VTCR1_EOFF_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_EOFF_SHIFT 3 -#define DDR_PHY_VTCR1_EOFF_MASK 0x00000018U - -/*Number of LCDL Eye points for which VREF training is repeated*/ -#undef DDR_PHY_VTCR1_ENUM_DEFVAL -#undef DDR_PHY_VTCR1_ENUM_SHIFT -#undef DDR_PHY_VTCR1_ENUM_MASK -#define DDR_PHY_VTCR1_ENUM_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_ENUM_SHIFT 2 -#define DDR_PHY_VTCR1_ENUM_MASK 0x00000004U - -/*HOST (IO) internal VREF training Enable*/ -#undef DDR_PHY_VTCR1_HVEN_DEFVAL -#undef DDR_PHY_VTCR1_HVEN_SHIFT -#undef DDR_PHY_VTCR1_HVEN_MASK -#define DDR_PHY_VTCR1_HVEN_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_HVEN_SHIFT 1 -#define DDR_PHY_VTCR1_HVEN_MASK 0x00000002U - -/*Host IO Type Control*/ -#undef DDR_PHY_VTCR1_HVIO_DEFVAL -#undef DDR_PHY_VTCR1_HVIO_SHIFT -#undef DDR_PHY_VTCR1_HVIO_MASK -#define DDR_PHY_VTCR1_HVIO_DEFVAL 0x07F00072 -#define DDR_PHY_VTCR1_HVIO_SHIFT 0 -#define DDR_PHY_VTCR1_HVIO_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR1_RESERVED_31_30_DEFVAL -#undef DDR_PHY_ACBDLR1_RESERVED_31_30_SHIFT -#undef DDR_PHY_ACBDLR1_RESERVED_31_30_MASK -#define DDR_PHY_ACBDLR1_RESERVED_31_30_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR1_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_ACBDLR1_RESERVED_31_30_MASK 0xC0000000U - -/*Delay select for the BDL on Parity.*/ -#undef DDR_PHY_ACBDLR1_PARBD_DEFVAL -#undef DDR_PHY_ACBDLR1_PARBD_SHIFT -#undef DDR_PHY_ACBDLR1_PARBD_MASK -#define DDR_PHY_ACBDLR1_PARBD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR1_PARBD_SHIFT 24 -#define DDR_PHY_ACBDLR1_PARBD_MASK 0x3F000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR1_RESERVED_23_22_DEFVAL -#undef DDR_PHY_ACBDLR1_RESERVED_23_22_SHIFT -#undef DDR_PHY_ACBDLR1_RESERVED_23_22_MASK -#define DDR_PHY_ACBDLR1_RESERVED_23_22_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR1_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_ACBDLR1_RESERVED_23_22_MASK 0x00C00000U - -/*Delay select for the BDL on Address A[16]. In DDR3 mode this pin is connected to WE.*/ -#undef DDR_PHY_ACBDLR1_A16BD_DEFVAL -#undef DDR_PHY_ACBDLR1_A16BD_SHIFT -#undef DDR_PHY_ACBDLR1_A16BD_MASK -#define DDR_PHY_ACBDLR1_A16BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR1_A16BD_SHIFT 16 -#define DDR_PHY_ACBDLR1_A16BD_MASK 0x003F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR1_RESERVED_15_14_DEFVAL -#undef DDR_PHY_ACBDLR1_RESERVED_15_14_SHIFT -#undef DDR_PHY_ACBDLR1_RESERVED_15_14_MASK -#define DDR_PHY_ACBDLR1_RESERVED_15_14_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR1_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_ACBDLR1_RESERVED_15_14_MASK 0x0000C000U - -/*Delay select for the BDL on Address A[17]. When not in DDR4 modemode this pin is connected to CAS.*/ -#undef DDR_PHY_ACBDLR1_A17BD_DEFVAL -#undef DDR_PHY_ACBDLR1_A17BD_SHIFT -#undef DDR_PHY_ACBDLR1_A17BD_MASK -#define DDR_PHY_ACBDLR1_A17BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR1_A17BD_SHIFT 8 -#define DDR_PHY_ACBDLR1_A17BD_MASK 0x00003F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR1_RESERVED_7_6_DEFVAL -#undef DDR_PHY_ACBDLR1_RESERVED_7_6_SHIFT -#undef DDR_PHY_ACBDLR1_RESERVED_7_6_MASK -#define DDR_PHY_ACBDLR1_RESERVED_7_6_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR1_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_ACBDLR1_RESERVED_7_6_MASK 0x000000C0U - -/*Delay select for the BDL on ACTN.*/ -#undef DDR_PHY_ACBDLR1_ACTBD_DEFVAL -#undef DDR_PHY_ACBDLR1_ACTBD_SHIFT -#undef DDR_PHY_ACBDLR1_ACTBD_MASK -#define DDR_PHY_ACBDLR1_ACTBD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR1_ACTBD_SHIFT 0 -#define DDR_PHY_ACBDLR1_ACTBD_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR2_RESERVED_31_30_DEFVAL -#undef DDR_PHY_ACBDLR2_RESERVED_31_30_SHIFT -#undef DDR_PHY_ACBDLR2_RESERVED_31_30_MASK -#define DDR_PHY_ACBDLR2_RESERVED_31_30_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR2_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_ACBDLR2_RESERVED_31_30_MASK 0xC0000000U - -/*Delay select for the BDL on BG[1].*/ -#undef DDR_PHY_ACBDLR2_BG1BD_DEFVAL -#undef DDR_PHY_ACBDLR2_BG1BD_SHIFT -#undef DDR_PHY_ACBDLR2_BG1BD_MASK -#define DDR_PHY_ACBDLR2_BG1BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR2_BG1BD_SHIFT 24 -#define DDR_PHY_ACBDLR2_BG1BD_MASK 0x3F000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR2_RESERVED_23_22_DEFVAL -#undef DDR_PHY_ACBDLR2_RESERVED_23_22_SHIFT -#undef DDR_PHY_ACBDLR2_RESERVED_23_22_MASK -#define DDR_PHY_ACBDLR2_RESERVED_23_22_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR2_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_ACBDLR2_RESERVED_23_22_MASK 0x00C00000U - -/*Delay select for the BDL on BG[0].*/ -#undef DDR_PHY_ACBDLR2_BG0BD_DEFVAL -#undef DDR_PHY_ACBDLR2_BG0BD_SHIFT -#undef DDR_PHY_ACBDLR2_BG0BD_MASK -#define DDR_PHY_ACBDLR2_BG0BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR2_BG0BD_SHIFT 16 -#define DDR_PHY_ACBDLR2_BG0BD_MASK 0x003F0000U - -/*Reser.ved Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR2_RESERVED_15_14_DEFVAL -#undef DDR_PHY_ACBDLR2_RESERVED_15_14_SHIFT -#undef DDR_PHY_ACBDLR2_RESERVED_15_14_MASK -#define DDR_PHY_ACBDLR2_RESERVED_15_14_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR2_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_ACBDLR2_RESERVED_15_14_MASK 0x0000C000U - -/*Delay select for the BDL on BA[1].*/ -#undef DDR_PHY_ACBDLR2_BA1BD_DEFVAL -#undef DDR_PHY_ACBDLR2_BA1BD_SHIFT -#undef DDR_PHY_ACBDLR2_BA1BD_MASK -#define DDR_PHY_ACBDLR2_BA1BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR2_BA1BD_SHIFT 8 -#define DDR_PHY_ACBDLR2_BA1BD_MASK 0x00003F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR2_RESERVED_7_6_DEFVAL -#undef DDR_PHY_ACBDLR2_RESERVED_7_6_SHIFT -#undef DDR_PHY_ACBDLR2_RESERVED_7_6_MASK -#define DDR_PHY_ACBDLR2_RESERVED_7_6_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR2_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_ACBDLR2_RESERVED_7_6_MASK 0x000000C0U - -/*Delay select for the BDL on BA[0].*/ -#undef DDR_PHY_ACBDLR2_BA0BD_DEFVAL -#undef DDR_PHY_ACBDLR2_BA0BD_SHIFT -#undef DDR_PHY_ACBDLR2_BA0BD_MASK -#define DDR_PHY_ACBDLR2_BA0BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR2_BA0BD_SHIFT 0 -#define DDR_PHY_ACBDLR2_BA0BD_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR6_RESERVED_31_30_DEFVAL -#undef DDR_PHY_ACBDLR6_RESERVED_31_30_SHIFT -#undef DDR_PHY_ACBDLR6_RESERVED_31_30_MASK -#define DDR_PHY_ACBDLR6_RESERVED_31_30_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR6_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_ACBDLR6_RESERVED_31_30_MASK 0xC0000000U - -/*Delay select for the BDL on Address A[3].*/ -#undef DDR_PHY_ACBDLR6_A03BD_DEFVAL -#undef DDR_PHY_ACBDLR6_A03BD_SHIFT -#undef DDR_PHY_ACBDLR6_A03BD_MASK -#define DDR_PHY_ACBDLR6_A03BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR6_A03BD_SHIFT 24 -#define DDR_PHY_ACBDLR6_A03BD_MASK 0x3F000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR6_RESERVED_23_22_DEFVAL -#undef DDR_PHY_ACBDLR6_RESERVED_23_22_SHIFT -#undef DDR_PHY_ACBDLR6_RESERVED_23_22_MASK -#define DDR_PHY_ACBDLR6_RESERVED_23_22_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR6_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_ACBDLR6_RESERVED_23_22_MASK 0x00C00000U - -/*Delay select for the BDL on Address A[2].*/ -#undef DDR_PHY_ACBDLR6_A02BD_DEFVAL -#undef DDR_PHY_ACBDLR6_A02BD_SHIFT -#undef DDR_PHY_ACBDLR6_A02BD_MASK -#define DDR_PHY_ACBDLR6_A02BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR6_A02BD_SHIFT 16 -#define DDR_PHY_ACBDLR6_A02BD_MASK 0x003F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR6_RESERVED_15_14_DEFVAL -#undef DDR_PHY_ACBDLR6_RESERVED_15_14_SHIFT -#undef DDR_PHY_ACBDLR6_RESERVED_15_14_MASK -#define DDR_PHY_ACBDLR6_RESERVED_15_14_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR6_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_ACBDLR6_RESERVED_15_14_MASK 0x0000C000U - -/*Delay select for the BDL on Address A[1].*/ -#undef DDR_PHY_ACBDLR6_A01BD_DEFVAL -#undef DDR_PHY_ACBDLR6_A01BD_SHIFT -#undef DDR_PHY_ACBDLR6_A01BD_MASK -#define DDR_PHY_ACBDLR6_A01BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR6_A01BD_SHIFT 8 -#define DDR_PHY_ACBDLR6_A01BD_MASK 0x00003F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_ACBDLR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_ACBDLR6_RESERVED_7_6_MASK -#define DDR_PHY_ACBDLR6_RESERVED_7_6_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_ACBDLR6_RESERVED_7_6_MASK 0x000000C0U - -/*Delay select for the BDL on Address A[0].*/ -#undef DDR_PHY_ACBDLR6_A00BD_DEFVAL -#undef DDR_PHY_ACBDLR6_A00BD_SHIFT -#undef DDR_PHY_ACBDLR6_A00BD_MASK -#define DDR_PHY_ACBDLR6_A00BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR6_A00BD_SHIFT 0 -#define DDR_PHY_ACBDLR6_A00BD_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR7_RESERVED_31_30_DEFVAL -#undef DDR_PHY_ACBDLR7_RESERVED_31_30_SHIFT -#undef DDR_PHY_ACBDLR7_RESERVED_31_30_MASK -#define DDR_PHY_ACBDLR7_RESERVED_31_30_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR7_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_ACBDLR7_RESERVED_31_30_MASK 0xC0000000U - -/*Delay select for the BDL on Address A[7].*/ -#undef DDR_PHY_ACBDLR7_A07BD_DEFVAL -#undef DDR_PHY_ACBDLR7_A07BD_SHIFT -#undef DDR_PHY_ACBDLR7_A07BD_MASK -#define DDR_PHY_ACBDLR7_A07BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR7_A07BD_SHIFT 24 -#define DDR_PHY_ACBDLR7_A07BD_MASK 0x3F000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR7_RESERVED_23_22_DEFVAL -#undef DDR_PHY_ACBDLR7_RESERVED_23_22_SHIFT -#undef DDR_PHY_ACBDLR7_RESERVED_23_22_MASK -#define DDR_PHY_ACBDLR7_RESERVED_23_22_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR7_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_ACBDLR7_RESERVED_23_22_MASK 0x00C00000U - -/*Delay select for the BDL on Address A[6].*/ -#undef DDR_PHY_ACBDLR7_A06BD_DEFVAL -#undef DDR_PHY_ACBDLR7_A06BD_SHIFT -#undef DDR_PHY_ACBDLR7_A06BD_MASK -#define DDR_PHY_ACBDLR7_A06BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR7_A06BD_SHIFT 16 -#define DDR_PHY_ACBDLR7_A06BD_MASK 0x003F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR7_RESERVED_15_14_DEFVAL -#undef DDR_PHY_ACBDLR7_RESERVED_15_14_SHIFT -#undef DDR_PHY_ACBDLR7_RESERVED_15_14_MASK -#define DDR_PHY_ACBDLR7_RESERVED_15_14_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR7_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_ACBDLR7_RESERVED_15_14_MASK 0x0000C000U - -/*Delay select for the BDL on Address A[5].*/ -#undef DDR_PHY_ACBDLR7_A05BD_DEFVAL -#undef DDR_PHY_ACBDLR7_A05BD_SHIFT -#undef DDR_PHY_ACBDLR7_A05BD_MASK -#define DDR_PHY_ACBDLR7_A05BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR7_A05BD_SHIFT 8 -#define DDR_PHY_ACBDLR7_A05BD_MASK 0x00003F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR7_RESERVED_7_6_DEFVAL -#undef DDR_PHY_ACBDLR7_RESERVED_7_6_SHIFT -#undef DDR_PHY_ACBDLR7_RESERVED_7_6_MASK -#define DDR_PHY_ACBDLR7_RESERVED_7_6_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR7_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_ACBDLR7_RESERVED_7_6_MASK 0x000000C0U - -/*Delay select for the BDL on Address A[4].*/ -#undef DDR_PHY_ACBDLR7_A04BD_DEFVAL -#undef DDR_PHY_ACBDLR7_A04BD_SHIFT -#undef DDR_PHY_ACBDLR7_A04BD_MASK -#define DDR_PHY_ACBDLR7_A04BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR7_A04BD_SHIFT 0 -#define DDR_PHY_ACBDLR7_A04BD_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR8_RESERVED_31_30_DEFVAL -#undef DDR_PHY_ACBDLR8_RESERVED_31_30_SHIFT -#undef DDR_PHY_ACBDLR8_RESERVED_31_30_MASK -#define DDR_PHY_ACBDLR8_RESERVED_31_30_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR8_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_ACBDLR8_RESERVED_31_30_MASK 0xC0000000U - -/*Delay select for the BDL on Address A[11].*/ -#undef DDR_PHY_ACBDLR8_A11BD_DEFVAL -#undef DDR_PHY_ACBDLR8_A11BD_SHIFT -#undef DDR_PHY_ACBDLR8_A11BD_MASK -#define DDR_PHY_ACBDLR8_A11BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR8_A11BD_SHIFT 24 -#define DDR_PHY_ACBDLR8_A11BD_MASK 0x3F000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR8_RESERVED_23_22_DEFVAL -#undef DDR_PHY_ACBDLR8_RESERVED_23_22_SHIFT -#undef DDR_PHY_ACBDLR8_RESERVED_23_22_MASK -#define DDR_PHY_ACBDLR8_RESERVED_23_22_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR8_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_ACBDLR8_RESERVED_23_22_MASK 0x00C00000U - -/*Delay select for the BDL on Address A[10].*/ -#undef DDR_PHY_ACBDLR8_A10BD_DEFVAL -#undef DDR_PHY_ACBDLR8_A10BD_SHIFT -#undef DDR_PHY_ACBDLR8_A10BD_MASK -#define DDR_PHY_ACBDLR8_A10BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR8_A10BD_SHIFT 16 -#define DDR_PHY_ACBDLR8_A10BD_MASK 0x003F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR8_RESERVED_15_14_DEFVAL -#undef DDR_PHY_ACBDLR8_RESERVED_15_14_SHIFT -#undef DDR_PHY_ACBDLR8_RESERVED_15_14_MASK -#define DDR_PHY_ACBDLR8_RESERVED_15_14_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR8_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_ACBDLR8_RESERVED_15_14_MASK 0x0000C000U - -/*Delay select for the BDL on Address A[9].*/ -#undef DDR_PHY_ACBDLR8_A09BD_DEFVAL -#undef DDR_PHY_ACBDLR8_A09BD_SHIFT -#undef DDR_PHY_ACBDLR8_A09BD_MASK -#define DDR_PHY_ACBDLR8_A09BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR8_A09BD_SHIFT 8 -#define DDR_PHY_ACBDLR8_A09BD_MASK 0x00003F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR8_RESERVED_7_6_DEFVAL -#undef DDR_PHY_ACBDLR8_RESERVED_7_6_SHIFT -#undef DDR_PHY_ACBDLR8_RESERVED_7_6_MASK -#define DDR_PHY_ACBDLR8_RESERVED_7_6_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR8_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_ACBDLR8_RESERVED_7_6_MASK 0x000000C0U - -/*Delay select for the BDL on Address A[8].*/ -#undef DDR_PHY_ACBDLR8_A08BD_DEFVAL -#undef DDR_PHY_ACBDLR8_A08BD_SHIFT -#undef DDR_PHY_ACBDLR8_A08BD_MASK -#define DDR_PHY_ACBDLR8_A08BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR8_A08BD_SHIFT 0 -#define DDR_PHY_ACBDLR8_A08BD_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR9_RESERVED_31_30_DEFVAL -#undef DDR_PHY_ACBDLR9_RESERVED_31_30_SHIFT -#undef DDR_PHY_ACBDLR9_RESERVED_31_30_MASK -#define DDR_PHY_ACBDLR9_RESERVED_31_30_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR9_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_ACBDLR9_RESERVED_31_30_MASK 0xC0000000U - -/*Delay select for the BDL on Address A[15].*/ -#undef DDR_PHY_ACBDLR9_A15BD_DEFVAL -#undef DDR_PHY_ACBDLR9_A15BD_SHIFT -#undef DDR_PHY_ACBDLR9_A15BD_MASK -#define DDR_PHY_ACBDLR9_A15BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR9_A15BD_SHIFT 24 -#define DDR_PHY_ACBDLR9_A15BD_MASK 0x3F000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR9_RESERVED_23_22_DEFVAL -#undef DDR_PHY_ACBDLR9_RESERVED_23_22_SHIFT -#undef DDR_PHY_ACBDLR9_RESERVED_23_22_MASK -#define DDR_PHY_ACBDLR9_RESERVED_23_22_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR9_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_ACBDLR9_RESERVED_23_22_MASK 0x00C00000U - -/*Delay select for the BDL on Address A[14].*/ -#undef DDR_PHY_ACBDLR9_A14BD_DEFVAL -#undef DDR_PHY_ACBDLR9_A14BD_SHIFT -#undef DDR_PHY_ACBDLR9_A14BD_MASK -#define DDR_PHY_ACBDLR9_A14BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR9_A14BD_SHIFT 16 -#define DDR_PHY_ACBDLR9_A14BD_MASK 0x003F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR9_RESERVED_15_14_DEFVAL -#undef DDR_PHY_ACBDLR9_RESERVED_15_14_SHIFT -#undef DDR_PHY_ACBDLR9_RESERVED_15_14_MASK -#define DDR_PHY_ACBDLR9_RESERVED_15_14_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR9_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_ACBDLR9_RESERVED_15_14_MASK 0x0000C000U - -/*Delay select for the BDL on Address A[13].*/ -#undef DDR_PHY_ACBDLR9_A13BD_DEFVAL -#undef DDR_PHY_ACBDLR9_A13BD_SHIFT -#undef DDR_PHY_ACBDLR9_A13BD_MASK -#define DDR_PHY_ACBDLR9_A13BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR9_A13BD_SHIFT 8 -#define DDR_PHY_ACBDLR9_A13BD_MASK 0x00003F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ACBDLR9_RESERVED_7_6_DEFVAL -#undef DDR_PHY_ACBDLR9_RESERVED_7_6_SHIFT -#undef DDR_PHY_ACBDLR9_RESERVED_7_6_MASK -#define DDR_PHY_ACBDLR9_RESERVED_7_6_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR9_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_ACBDLR9_RESERVED_7_6_MASK 0x000000C0U - -/*Delay select for the BDL on Address A[12].*/ -#undef DDR_PHY_ACBDLR9_A12BD_DEFVAL -#undef DDR_PHY_ACBDLR9_A12BD_SHIFT -#undef DDR_PHY_ACBDLR9_A12BD_MASK -#define DDR_PHY_ACBDLR9_A12BD_DEFVAL 0x00000000 -#define DDR_PHY_ACBDLR9_A12BD_SHIFT 0 -#define DDR_PHY_ACBDLR9_A12BD_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_ZQCR_RESERVED_31_26_DEFVAL -#undef DDR_PHY_ZQCR_RESERVED_31_26_SHIFT -#undef DDR_PHY_ZQCR_RESERVED_31_26_MASK -#define DDR_PHY_ZQCR_RESERVED_31_26_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_RESERVED_31_26_SHIFT 26 -#define DDR_PHY_ZQCR_RESERVED_31_26_MASK 0xFC000000U - -/*ZQ VREF Range*/ -#undef DDR_PHY_ZQCR_ZQREFISELRANGE_DEFVAL -#undef DDR_PHY_ZQCR_ZQREFISELRANGE_SHIFT -#undef DDR_PHY_ZQCR_ZQREFISELRANGE_MASK -#define DDR_PHY_ZQCR_ZQREFISELRANGE_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_ZQREFISELRANGE_SHIFT 25 -#define DDR_PHY_ZQCR_ZQREFISELRANGE_MASK 0x02000000U - -/*Programmable Wait for Frequency B*/ -#undef DDR_PHY_ZQCR_PGWAIT_FRQB_DEFVAL -#undef DDR_PHY_ZQCR_PGWAIT_FRQB_SHIFT -#undef DDR_PHY_ZQCR_PGWAIT_FRQB_MASK -#define DDR_PHY_ZQCR_PGWAIT_FRQB_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_PGWAIT_FRQB_SHIFT 19 -#define DDR_PHY_ZQCR_PGWAIT_FRQB_MASK 0x01F80000U - -/*Programmable Wait for Frequency A*/ -#undef DDR_PHY_ZQCR_PGWAIT_FRQA_DEFVAL -#undef DDR_PHY_ZQCR_PGWAIT_FRQA_SHIFT -#undef DDR_PHY_ZQCR_PGWAIT_FRQA_MASK -#define DDR_PHY_ZQCR_PGWAIT_FRQA_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_PGWAIT_FRQA_SHIFT 13 -#define DDR_PHY_ZQCR_PGWAIT_FRQA_MASK 0x0007E000U - -/*ZQ VREF Pad Enable*/ -#undef DDR_PHY_ZQCR_ZQREFPEN_DEFVAL -#undef DDR_PHY_ZQCR_ZQREFPEN_SHIFT -#undef DDR_PHY_ZQCR_ZQREFPEN_MASK -#define DDR_PHY_ZQCR_ZQREFPEN_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_ZQREFPEN_SHIFT 12 -#define DDR_PHY_ZQCR_ZQREFPEN_MASK 0x00001000U - -/*ZQ Internal VREF Enable*/ -#undef DDR_PHY_ZQCR_ZQREFIEN_DEFVAL -#undef DDR_PHY_ZQCR_ZQREFIEN_SHIFT -#undef DDR_PHY_ZQCR_ZQREFIEN_MASK -#define DDR_PHY_ZQCR_ZQREFIEN_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_ZQREFIEN_SHIFT 11 -#define DDR_PHY_ZQCR_ZQREFIEN_MASK 0x00000800U - -/*Choice of termination mode*/ -#undef DDR_PHY_ZQCR_ODT_MODE_DEFVAL -#undef DDR_PHY_ZQCR_ODT_MODE_SHIFT -#undef DDR_PHY_ZQCR_ODT_MODE_MASK -#define DDR_PHY_ZQCR_ODT_MODE_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_ODT_MODE_SHIFT 9 -#define DDR_PHY_ZQCR_ODT_MODE_MASK 0x00000600U - -/*Force ZCAL VT update*/ -#undef DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE_DEFVAL -#undef DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE_SHIFT -#undef DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE_MASK -#define DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE_SHIFT 8 -#define DDR_PHY_ZQCR_FORCE_ZCAL_VT_UPDATE_MASK 0x00000100U - -/*IO VT Drift Limit*/ -#undef DDR_PHY_ZQCR_IODLMT_DEFVAL -#undef DDR_PHY_ZQCR_IODLMT_SHIFT -#undef DDR_PHY_ZQCR_IODLMT_MASK -#define DDR_PHY_ZQCR_IODLMT_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_IODLMT_SHIFT 5 -#define DDR_PHY_ZQCR_IODLMT_MASK 0x000000E0U - -/*Averaging algorithm enable, if set, enables averaging algorithm*/ -#undef DDR_PHY_ZQCR_AVGEN_DEFVAL -#undef DDR_PHY_ZQCR_AVGEN_SHIFT -#undef DDR_PHY_ZQCR_AVGEN_MASK -#define DDR_PHY_ZQCR_AVGEN_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_AVGEN_SHIFT 4 -#define DDR_PHY_ZQCR_AVGEN_MASK 0x00000010U - -/*Maximum number of averaging rounds to be used by averaging algorithm*/ -#undef DDR_PHY_ZQCR_AVGMAX_DEFVAL -#undef DDR_PHY_ZQCR_AVGMAX_SHIFT -#undef DDR_PHY_ZQCR_AVGMAX_MASK -#define DDR_PHY_ZQCR_AVGMAX_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_AVGMAX_SHIFT 2 -#define DDR_PHY_ZQCR_AVGMAX_MASK 0x0000000CU - -/*ZQ Calibration Type*/ -#undef DDR_PHY_ZQCR_ZCALT_DEFVAL -#undef DDR_PHY_ZQCR_ZCALT_SHIFT -#undef DDR_PHY_ZQCR_ZCALT_MASK -#define DDR_PHY_ZQCR_ZCALT_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_ZCALT_SHIFT 1 -#define DDR_PHY_ZQCR_ZCALT_MASK 0x00000002U - -/*ZQ Power Down*/ -#undef DDR_PHY_ZQCR_ZQPD_DEFVAL -#undef DDR_PHY_ZQCR_ZQPD_SHIFT -#undef DDR_PHY_ZQCR_ZQPD_MASK -#define DDR_PHY_ZQCR_ZQPD_DEFVAL 0x008A2858 -#define DDR_PHY_ZQCR_ZQPD_SHIFT 0 -#define DDR_PHY_ZQCR_ZQPD_MASK 0x00000001U - -/*Pull-down drive strength ZCTRL over-ride enable*/ -#undef DDR_PHY_ZQ0PR0_PD_DRV_ZDEN_DEFVAL -#undef DDR_PHY_ZQ0PR0_PD_DRV_ZDEN_SHIFT -#undef DDR_PHY_ZQ0PR0_PD_DRV_ZDEN_MASK -#define DDR_PHY_ZQ0PR0_PD_DRV_ZDEN_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_PD_DRV_ZDEN_SHIFT 31 -#define DDR_PHY_ZQ0PR0_PD_DRV_ZDEN_MASK 0x80000000U - -/*Pull-up drive strength ZCTRL over-ride enable*/ -#undef DDR_PHY_ZQ0PR0_PU_DRV_ZDEN_DEFVAL -#undef DDR_PHY_ZQ0PR0_PU_DRV_ZDEN_SHIFT -#undef DDR_PHY_ZQ0PR0_PU_DRV_ZDEN_MASK -#define DDR_PHY_ZQ0PR0_PU_DRV_ZDEN_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_PU_DRV_ZDEN_SHIFT 30 -#define DDR_PHY_ZQ0PR0_PU_DRV_ZDEN_MASK 0x40000000U - -/*Pull-down termination ZCTRL over-ride enable*/ -#undef DDR_PHY_ZQ0PR0_PD_ODT_ZDEN_DEFVAL -#undef DDR_PHY_ZQ0PR0_PD_ODT_ZDEN_SHIFT -#undef DDR_PHY_ZQ0PR0_PD_ODT_ZDEN_MASK -#define DDR_PHY_ZQ0PR0_PD_ODT_ZDEN_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_PD_ODT_ZDEN_SHIFT 29 -#define DDR_PHY_ZQ0PR0_PD_ODT_ZDEN_MASK 0x20000000U - -/*Pull-up termination ZCTRL over-ride enable*/ -#undef DDR_PHY_ZQ0PR0_PU_ODT_ZDEN_DEFVAL -#undef DDR_PHY_ZQ0PR0_PU_ODT_ZDEN_SHIFT -#undef DDR_PHY_ZQ0PR0_PU_ODT_ZDEN_MASK -#define DDR_PHY_ZQ0PR0_PU_ODT_ZDEN_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_PU_ODT_ZDEN_SHIFT 28 -#define DDR_PHY_ZQ0PR0_PU_ODT_ZDEN_MASK 0x10000000U - -/*Calibration segment bypass*/ -#undef DDR_PHY_ZQ0PR0_ZSEGBYP_DEFVAL -#undef DDR_PHY_ZQ0PR0_ZSEGBYP_SHIFT -#undef DDR_PHY_ZQ0PR0_ZSEGBYP_MASK -#define DDR_PHY_ZQ0PR0_ZSEGBYP_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_ZSEGBYP_SHIFT 27 -#define DDR_PHY_ZQ0PR0_ZSEGBYP_MASK 0x08000000U - -/*VREF latch mode controls the mode in which the ZLE pin of the PVREF cell is driven by the PUB*/ -#undef DDR_PHY_ZQ0PR0_ZLE_MODE_DEFVAL -#undef DDR_PHY_ZQ0PR0_ZLE_MODE_SHIFT -#undef DDR_PHY_ZQ0PR0_ZLE_MODE_MASK -#define DDR_PHY_ZQ0PR0_ZLE_MODE_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_ZLE_MODE_SHIFT 25 -#define DDR_PHY_ZQ0PR0_ZLE_MODE_MASK 0x06000000U - -/*Termination adjustment*/ -#undef DDR_PHY_ZQ0PR0_ODT_ADJUST_DEFVAL -#undef DDR_PHY_ZQ0PR0_ODT_ADJUST_SHIFT -#undef DDR_PHY_ZQ0PR0_ODT_ADJUST_MASK -#define DDR_PHY_ZQ0PR0_ODT_ADJUST_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_ODT_ADJUST_SHIFT 22 -#define DDR_PHY_ZQ0PR0_ODT_ADJUST_MASK 0x01C00000U - -/*Pulldown drive strength adjustment*/ -#undef DDR_PHY_ZQ0PR0_PD_DRV_ADJUST_DEFVAL -#undef DDR_PHY_ZQ0PR0_PD_DRV_ADJUST_SHIFT -#undef DDR_PHY_ZQ0PR0_PD_DRV_ADJUST_MASK -#define DDR_PHY_ZQ0PR0_PD_DRV_ADJUST_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_PD_DRV_ADJUST_SHIFT 19 -#define DDR_PHY_ZQ0PR0_PD_DRV_ADJUST_MASK 0x00380000U - -/*Pullup drive strength adjustment*/ -#undef DDR_PHY_ZQ0PR0_PU_DRV_ADJUST_DEFVAL -#undef DDR_PHY_ZQ0PR0_PU_DRV_ADJUST_SHIFT -#undef DDR_PHY_ZQ0PR0_PU_DRV_ADJUST_MASK -#define DDR_PHY_ZQ0PR0_PU_DRV_ADJUST_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_PU_DRV_ADJUST_SHIFT 16 -#define DDR_PHY_ZQ0PR0_PU_DRV_ADJUST_MASK 0x00070000U - -/*DRAM Impedance Divide Ratio*/ -#undef DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT_DEFVAL -#undef DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT_SHIFT -#undef DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT_MASK -#define DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT_SHIFT 12 -#define DDR_PHY_ZQ0PR0_ZPROG_DRAM_ODT_MASK 0x0000F000U - -/*HOST Impedance Divide Ratio*/ -#undef DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT_DEFVAL -#undef DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT_SHIFT -#undef DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT_MASK -#define DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT_SHIFT 8 -#define DDR_PHY_ZQ0PR0_ZPROG_HOST_ODT_MASK 0x00000F00U - -/*Impedance Divide Ratio (pulldown drive calibration during asymmetric drive strength calibration)*/ -#undef DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD_DEFVAL -#undef DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD_SHIFT -#undef DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD_MASK -#define DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD_SHIFT 4 -#define DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PD_MASK 0x000000F0U - -/*Impedance Divide Ratio (pullup drive calibration during asymmetric drive strength calibration)*/ -#undef DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU_DEFVAL -#undef DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU_SHIFT -#undef DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU_MASK -#define DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU_DEFVAL 0x000077BB -#define DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU_SHIFT 0 -#define DDR_PHY_ZQ0PR0_ZPROG_ASYM_DRV_PU_MASK 0x0000000FU - -/*Reserved. Return zeros on reads.*/ -#undef DDR_PHY_ZQ0OR0_RESERVED_31_26_DEFVAL -#undef DDR_PHY_ZQ0OR0_RESERVED_31_26_SHIFT -#undef DDR_PHY_ZQ0OR0_RESERVED_31_26_MASK -#define DDR_PHY_ZQ0OR0_RESERVED_31_26_DEFVAL 0x00000000 -#define DDR_PHY_ZQ0OR0_RESERVED_31_26_SHIFT 26 -#define DDR_PHY_ZQ0OR0_RESERVED_31_26_MASK 0xFC000000U - -/*Override value for the pull-up output impedance*/ -#undef DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD_DEFVAL -#undef DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD_SHIFT -#undef DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD_MASK -#define DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD_DEFVAL 0x00000000 -#define DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD_SHIFT 16 -#define DDR_PHY_ZQ0OR0_ZDATA_PU_DRV_OVRD_MASK 0x03FF0000U - -/*Reserved. Return zeros on reads.*/ -#undef DDR_PHY_ZQ0OR0_RESERVED_15_10_DEFVAL -#undef DDR_PHY_ZQ0OR0_RESERVED_15_10_SHIFT -#undef DDR_PHY_ZQ0OR0_RESERVED_15_10_MASK -#define DDR_PHY_ZQ0OR0_RESERVED_15_10_DEFVAL 0x00000000 -#define DDR_PHY_ZQ0OR0_RESERVED_15_10_SHIFT 10 -#define DDR_PHY_ZQ0OR0_RESERVED_15_10_MASK 0x0000FC00U - -/*Override value for the pull-down output impedance*/ -#undef DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD_DEFVAL -#undef DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD_SHIFT -#undef DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD_MASK -#define DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD_DEFVAL 0x00000000 -#define DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD_SHIFT 0 -#define DDR_PHY_ZQ0OR0_ZDATA_PD_DRV_OVRD_MASK 0x000003FFU - -/*Reserved. Return zeros on reads.*/ -#undef DDR_PHY_ZQ0OR1_RESERVED_31_26_DEFVAL -#undef DDR_PHY_ZQ0OR1_RESERVED_31_26_SHIFT -#undef DDR_PHY_ZQ0OR1_RESERVED_31_26_MASK -#define DDR_PHY_ZQ0OR1_RESERVED_31_26_DEFVAL 0x00000000 -#define DDR_PHY_ZQ0OR1_RESERVED_31_26_SHIFT 26 -#define DDR_PHY_ZQ0OR1_RESERVED_31_26_MASK 0xFC000000U - -/*Override value for the pull-up termination*/ -#undef DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD_DEFVAL -#undef DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD_SHIFT -#undef DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD_MASK -#define DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD_DEFVAL 0x00000000 -#define DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD_SHIFT 16 -#define DDR_PHY_ZQ0OR1_ZDATA_PU_ODT_OVRD_MASK 0x03FF0000U - -/*Reserved. Return zeros on reads.*/ -#undef DDR_PHY_ZQ0OR1_RESERVED_15_10_DEFVAL -#undef DDR_PHY_ZQ0OR1_RESERVED_15_10_SHIFT -#undef DDR_PHY_ZQ0OR1_RESERVED_15_10_MASK -#define DDR_PHY_ZQ0OR1_RESERVED_15_10_DEFVAL 0x00000000 -#define DDR_PHY_ZQ0OR1_RESERVED_15_10_SHIFT 10 -#define DDR_PHY_ZQ0OR1_RESERVED_15_10_MASK 0x0000FC00U - -/*Override value for the pull-down termination*/ -#undef DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD_DEFVAL -#undef DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD_SHIFT -#undef DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD_MASK -#define DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD_DEFVAL 0x00000000 -#define DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD_SHIFT 0 -#define DDR_PHY_ZQ0OR1_ZDATA_PD_ODT_OVRD_MASK 0x000003FFU - -/*Pull-down drive strength ZCTRL over-ride enable*/ -#undef DDR_PHY_ZQ1PR0_PD_DRV_ZDEN_DEFVAL -#undef DDR_PHY_ZQ1PR0_PD_DRV_ZDEN_SHIFT -#undef DDR_PHY_ZQ1PR0_PD_DRV_ZDEN_MASK -#define DDR_PHY_ZQ1PR0_PD_DRV_ZDEN_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_PD_DRV_ZDEN_SHIFT 31 -#define DDR_PHY_ZQ1PR0_PD_DRV_ZDEN_MASK 0x80000000U - -/*Pull-up drive strength ZCTRL over-ride enable*/ -#undef DDR_PHY_ZQ1PR0_PU_DRV_ZDEN_DEFVAL -#undef DDR_PHY_ZQ1PR0_PU_DRV_ZDEN_SHIFT -#undef DDR_PHY_ZQ1PR0_PU_DRV_ZDEN_MASK -#define DDR_PHY_ZQ1PR0_PU_DRV_ZDEN_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_PU_DRV_ZDEN_SHIFT 30 -#define DDR_PHY_ZQ1PR0_PU_DRV_ZDEN_MASK 0x40000000U - -/*Pull-down termination ZCTRL over-ride enable*/ -#undef DDR_PHY_ZQ1PR0_PD_ODT_ZDEN_DEFVAL -#undef DDR_PHY_ZQ1PR0_PD_ODT_ZDEN_SHIFT -#undef DDR_PHY_ZQ1PR0_PD_ODT_ZDEN_MASK -#define DDR_PHY_ZQ1PR0_PD_ODT_ZDEN_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_PD_ODT_ZDEN_SHIFT 29 -#define DDR_PHY_ZQ1PR0_PD_ODT_ZDEN_MASK 0x20000000U - -/*Pull-up termination ZCTRL over-ride enable*/ -#undef DDR_PHY_ZQ1PR0_PU_ODT_ZDEN_DEFVAL -#undef DDR_PHY_ZQ1PR0_PU_ODT_ZDEN_SHIFT -#undef DDR_PHY_ZQ1PR0_PU_ODT_ZDEN_MASK -#define DDR_PHY_ZQ1PR0_PU_ODT_ZDEN_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_PU_ODT_ZDEN_SHIFT 28 -#define DDR_PHY_ZQ1PR0_PU_ODT_ZDEN_MASK 0x10000000U - -/*Calibration segment bypass*/ -#undef DDR_PHY_ZQ1PR0_ZSEGBYP_DEFVAL -#undef DDR_PHY_ZQ1PR0_ZSEGBYP_SHIFT -#undef DDR_PHY_ZQ1PR0_ZSEGBYP_MASK -#define DDR_PHY_ZQ1PR0_ZSEGBYP_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_ZSEGBYP_SHIFT 27 -#define DDR_PHY_ZQ1PR0_ZSEGBYP_MASK 0x08000000U - -/*VREF latch mode controls the mode in which the ZLE pin of the PVREF cell is driven by the PUB*/ -#undef DDR_PHY_ZQ1PR0_ZLE_MODE_DEFVAL -#undef DDR_PHY_ZQ1PR0_ZLE_MODE_SHIFT -#undef DDR_PHY_ZQ1PR0_ZLE_MODE_MASK -#define DDR_PHY_ZQ1PR0_ZLE_MODE_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_ZLE_MODE_SHIFT 25 -#define DDR_PHY_ZQ1PR0_ZLE_MODE_MASK 0x06000000U - -/*Termination adjustment*/ -#undef DDR_PHY_ZQ1PR0_ODT_ADJUST_DEFVAL -#undef DDR_PHY_ZQ1PR0_ODT_ADJUST_SHIFT -#undef DDR_PHY_ZQ1PR0_ODT_ADJUST_MASK -#define DDR_PHY_ZQ1PR0_ODT_ADJUST_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_ODT_ADJUST_SHIFT 22 -#define DDR_PHY_ZQ1PR0_ODT_ADJUST_MASK 0x01C00000U - -/*Pulldown drive strength adjustment*/ -#undef DDR_PHY_ZQ1PR0_PD_DRV_ADJUST_DEFVAL -#undef DDR_PHY_ZQ1PR0_PD_DRV_ADJUST_SHIFT -#undef DDR_PHY_ZQ1PR0_PD_DRV_ADJUST_MASK -#define DDR_PHY_ZQ1PR0_PD_DRV_ADJUST_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_PD_DRV_ADJUST_SHIFT 19 -#define DDR_PHY_ZQ1PR0_PD_DRV_ADJUST_MASK 0x00380000U - -/*Pullup drive strength adjustment*/ -#undef DDR_PHY_ZQ1PR0_PU_DRV_ADJUST_DEFVAL -#undef DDR_PHY_ZQ1PR0_PU_DRV_ADJUST_SHIFT -#undef DDR_PHY_ZQ1PR0_PU_DRV_ADJUST_MASK -#define DDR_PHY_ZQ1PR0_PU_DRV_ADJUST_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_PU_DRV_ADJUST_SHIFT 16 -#define DDR_PHY_ZQ1PR0_PU_DRV_ADJUST_MASK 0x00070000U - -/*DRAM Impedance Divide Ratio*/ -#undef DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT_DEFVAL -#undef DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT_SHIFT -#undef DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT_MASK -#define DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT_SHIFT 12 -#define DDR_PHY_ZQ1PR0_ZPROG_DRAM_ODT_MASK 0x0000F000U - -/*HOST Impedance Divide Ratio*/ -#undef DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT_DEFVAL -#undef DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT_SHIFT -#undef DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT_MASK -#define DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT_SHIFT 8 -#define DDR_PHY_ZQ1PR0_ZPROG_HOST_ODT_MASK 0x00000F00U - -/*Impedance Divide Ratio (pulldown drive calibration during asymmetric drive strength calibration)*/ -#undef DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD_DEFVAL -#undef DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD_SHIFT -#undef DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD_MASK -#define DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD_SHIFT 4 -#define DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PD_MASK 0x000000F0U - -/*Impedance Divide Ratio (pullup drive calibration during asymmetric drive strength calibration)*/ -#undef DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU_DEFVAL -#undef DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU_SHIFT -#undef DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU_MASK -#define DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU_DEFVAL 0x000077BB -#define DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU_SHIFT 0 -#define DDR_PHY_ZQ1PR0_ZPROG_ASYM_DRV_PU_MASK 0x0000000FU - -/*Calibration Bypass*/ -#undef DDR_PHY_DX0GCR0_CALBYP_DEFVAL -#undef DDR_PHY_DX0GCR0_CALBYP_SHIFT -#undef DDR_PHY_DX0GCR0_CALBYP_MASK -#define DDR_PHY_DX0GCR0_CALBYP_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_CALBYP_SHIFT 31 -#define DDR_PHY_DX0GCR0_CALBYP_MASK 0x80000000U - -/*Master Delay Line Enable*/ -#undef DDR_PHY_DX0GCR0_MDLEN_DEFVAL -#undef DDR_PHY_DX0GCR0_MDLEN_SHIFT -#undef DDR_PHY_DX0GCR0_MDLEN_MASK -#define DDR_PHY_DX0GCR0_MDLEN_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_MDLEN_SHIFT 30 -#define DDR_PHY_DX0GCR0_MDLEN_MASK 0x40000000U - -/*Configurable ODT(TE) Phase Shift*/ -#undef DDR_PHY_DX0GCR0_CODTSHFT_DEFVAL -#undef DDR_PHY_DX0GCR0_CODTSHFT_SHIFT -#undef DDR_PHY_DX0GCR0_CODTSHFT_MASK -#define DDR_PHY_DX0GCR0_CODTSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_CODTSHFT_SHIFT 28 -#define DDR_PHY_DX0GCR0_CODTSHFT_MASK 0x30000000U - -/*DQS Duty Cycle Correction*/ -#undef DDR_PHY_DX0GCR0_DQSDCC_DEFVAL -#undef DDR_PHY_DX0GCR0_DQSDCC_SHIFT -#undef DDR_PHY_DX0GCR0_DQSDCC_MASK -#define DDR_PHY_DX0GCR0_DQSDCC_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_DQSDCC_SHIFT 24 -#define DDR_PHY_DX0GCR0_DQSDCC_MASK 0x0F000000U - -/*Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY*/ -#undef DDR_PHY_DX0GCR0_RDDLY_DEFVAL -#undef DDR_PHY_DX0GCR0_RDDLY_SHIFT -#undef DDR_PHY_DX0GCR0_RDDLY_MASK -#define DDR_PHY_DX0GCR0_RDDLY_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_RDDLY_SHIFT 20 -#define DDR_PHY_DX0GCR0_RDDLY_MASK 0x00F00000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX0GCR0_RESERVED_19_14_DEFVAL -#undef DDR_PHY_DX0GCR0_RESERVED_19_14_SHIFT -#undef DDR_PHY_DX0GCR0_RESERVED_19_14_MASK -#define DDR_PHY_DX0GCR0_RESERVED_19_14_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_RESERVED_19_14_SHIFT 14 -#define DDR_PHY_DX0GCR0_RESERVED_19_14_MASK 0x000FC000U - -/*DQSNSE Power Down Receiver*/ -#undef DDR_PHY_DX0GCR0_DQSNSEPDR_DEFVAL -#undef DDR_PHY_DX0GCR0_DQSNSEPDR_SHIFT -#undef DDR_PHY_DX0GCR0_DQSNSEPDR_MASK -#define DDR_PHY_DX0GCR0_DQSNSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_DQSNSEPDR_SHIFT 13 -#define DDR_PHY_DX0GCR0_DQSNSEPDR_MASK 0x00002000U - -/*DQSSE Power Down Receiver*/ -#undef DDR_PHY_DX0GCR0_DQSSEPDR_DEFVAL -#undef DDR_PHY_DX0GCR0_DQSSEPDR_SHIFT -#undef DDR_PHY_DX0GCR0_DQSSEPDR_MASK -#define DDR_PHY_DX0GCR0_DQSSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_DQSSEPDR_SHIFT 12 -#define DDR_PHY_DX0GCR0_DQSSEPDR_MASK 0x00001000U - -/*RTT On Additive Latency*/ -#undef DDR_PHY_DX0GCR0_RTTOAL_DEFVAL -#undef DDR_PHY_DX0GCR0_RTTOAL_SHIFT -#undef DDR_PHY_DX0GCR0_RTTOAL_MASK -#define DDR_PHY_DX0GCR0_RTTOAL_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_RTTOAL_SHIFT 11 -#define DDR_PHY_DX0GCR0_RTTOAL_MASK 0x00000800U - -/*RTT Output Hold*/ -#undef DDR_PHY_DX0GCR0_RTTOH_DEFVAL -#undef DDR_PHY_DX0GCR0_RTTOH_SHIFT -#undef DDR_PHY_DX0GCR0_RTTOH_MASK -#define DDR_PHY_DX0GCR0_RTTOH_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_RTTOH_SHIFT 9 -#define DDR_PHY_DX0GCR0_RTTOH_MASK 0x00000600U - -/*Configurable PDR Phase Shift*/ -#undef DDR_PHY_DX0GCR0_CPDRSHFT_DEFVAL -#undef DDR_PHY_DX0GCR0_CPDRSHFT_SHIFT -#undef DDR_PHY_DX0GCR0_CPDRSHFT_MASK -#define DDR_PHY_DX0GCR0_CPDRSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_CPDRSHFT_SHIFT 7 -#define DDR_PHY_DX0GCR0_CPDRSHFT_MASK 0x00000180U - -/*DQSR Power Down*/ -#undef DDR_PHY_DX0GCR0_DQSRPD_DEFVAL -#undef DDR_PHY_DX0GCR0_DQSRPD_SHIFT -#undef DDR_PHY_DX0GCR0_DQSRPD_MASK -#define DDR_PHY_DX0GCR0_DQSRPD_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_DQSRPD_SHIFT 6 -#define DDR_PHY_DX0GCR0_DQSRPD_MASK 0x00000040U - -/*DQSG Power Down Receiver*/ -#undef DDR_PHY_DX0GCR0_DQSGPDR_DEFVAL -#undef DDR_PHY_DX0GCR0_DQSGPDR_SHIFT -#undef DDR_PHY_DX0GCR0_DQSGPDR_MASK -#define DDR_PHY_DX0GCR0_DQSGPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_DQSGPDR_SHIFT 5 -#define DDR_PHY_DX0GCR0_DQSGPDR_MASK 0x00000020U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX0GCR0_RESERVED_4_DEFVAL -#undef DDR_PHY_DX0GCR0_RESERVED_4_SHIFT -#undef DDR_PHY_DX0GCR0_RESERVED_4_MASK -#define DDR_PHY_DX0GCR0_RESERVED_4_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_RESERVED_4_SHIFT 4 -#define DDR_PHY_DX0GCR0_RESERVED_4_MASK 0x00000010U - -/*DQSG On-Die Termination*/ -#undef DDR_PHY_DX0GCR0_DQSGODT_DEFVAL -#undef DDR_PHY_DX0GCR0_DQSGODT_SHIFT -#undef DDR_PHY_DX0GCR0_DQSGODT_MASK -#define DDR_PHY_DX0GCR0_DQSGODT_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_DQSGODT_SHIFT 3 -#define DDR_PHY_DX0GCR0_DQSGODT_MASK 0x00000008U - -/*DQSG Output Enable*/ -#undef DDR_PHY_DX0GCR0_DQSGOE_DEFVAL -#undef DDR_PHY_DX0GCR0_DQSGOE_SHIFT -#undef DDR_PHY_DX0GCR0_DQSGOE_MASK -#define DDR_PHY_DX0GCR0_DQSGOE_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_DQSGOE_SHIFT 2 -#define DDR_PHY_DX0GCR0_DQSGOE_MASK 0x00000004U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX0GCR0_RESERVED_1_0_DEFVAL -#undef DDR_PHY_DX0GCR0_RESERVED_1_0_SHIFT -#undef DDR_PHY_DX0GCR0_RESERVED_1_0_MASK -#define DDR_PHY_DX0GCR0_RESERVED_1_0_DEFVAL 0x40200204 -#define DDR_PHY_DX0GCR0_RESERVED_1_0_SHIFT 0 -#define DDR_PHY_DX0GCR0_RESERVED_1_0_MASK 0x00000003U - -/*Byte lane VREF IOM (Used only by D4MU IOs)*/ -#undef DDR_PHY_DX0GCR4_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DX0GCR4_RESERVED_31_29_SHIFT -#undef DDR_PHY_DX0GCR4_RESERVED_31_29_MASK -#define DDR_PHY_DX0GCR4_RESERVED_31_29_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DX0GCR4_RESERVED_31_29_MASK 0xE0000000U - -/*Byte Lane VREF Pad Enable*/ -#undef DDR_PHY_DX0GCR4_DXREFPEN_DEFVAL -#undef DDR_PHY_DX0GCR4_DXREFPEN_SHIFT -#undef DDR_PHY_DX0GCR4_DXREFPEN_MASK -#define DDR_PHY_DX0GCR4_DXREFPEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_DXREFPEN_SHIFT 28 -#define DDR_PHY_DX0GCR4_DXREFPEN_MASK 0x10000000U - -/*Byte Lane Internal VREF Enable*/ -#undef DDR_PHY_DX0GCR4_DXREFEEN_DEFVAL -#undef DDR_PHY_DX0GCR4_DXREFEEN_SHIFT -#undef DDR_PHY_DX0GCR4_DXREFEEN_MASK -#define DDR_PHY_DX0GCR4_DXREFEEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_DXREFEEN_SHIFT 26 -#define DDR_PHY_DX0GCR4_DXREFEEN_MASK 0x0C000000U - -/*Byte Lane Single-End VREF Enable*/ -#undef DDR_PHY_DX0GCR4_DXREFSEN_DEFVAL -#undef DDR_PHY_DX0GCR4_DXREFSEN_SHIFT -#undef DDR_PHY_DX0GCR4_DXREFSEN_MASK -#define DDR_PHY_DX0GCR4_DXREFSEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_DXREFSEN_SHIFT 25 -#define DDR_PHY_DX0GCR4_DXREFSEN_MASK 0x02000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX0GCR4_RESERVED_24_DEFVAL -#undef DDR_PHY_DX0GCR4_RESERVED_24_SHIFT -#undef DDR_PHY_DX0GCR4_RESERVED_24_MASK -#define DDR_PHY_DX0GCR4_RESERVED_24_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_RESERVED_24_SHIFT 24 -#define DDR_PHY_DX0GCR4_RESERVED_24_MASK 0x01000000U - -/*External VREF generator REFSEL range select*/ -#undef DDR_PHY_DX0GCR4_DXREFESELRANGE_DEFVAL -#undef DDR_PHY_DX0GCR4_DXREFESELRANGE_SHIFT -#undef DDR_PHY_DX0GCR4_DXREFESELRANGE_MASK -#define DDR_PHY_DX0GCR4_DXREFESELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_DXREFESELRANGE_SHIFT 23 -#define DDR_PHY_DX0GCR4_DXREFESELRANGE_MASK 0x00800000U - -/*Byte Lane External VREF Select*/ -#undef DDR_PHY_DX0GCR4_DXREFESEL_DEFVAL -#undef DDR_PHY_DX0GCR4_DXREFESEL_SHIFT -#undef DDR_PHY_DX0GCR4_DXREFESEL_MASK -#define DDR_PHY_DX0GCR4_DXREFESEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_DXREFESEL_SHIFT 16 -#define DDR_PHY_DX0GCR4_DXREFESEL_MASK 0x007F0000U - -/*Single ended VREF generator REFSEL range select*/ -#undef DDR_PHY_DX0GCR4_DXREFSSELRANGE_DEFVAL -#undef DDR_PHY_DX0GCR4_DXREFSSELRANGE_SHIFT -#undef DDR_PHY_DX0GCR4_DXREFSSELRANGE_MASK -#define DDR_PHY_DX0GCR4_DXREFSSELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_DXREFSSELRANGE_SHIFT 15 -#define DDR_PHY_DX0GCR4_DXREFSSELRANGE_MASK 0x00008000U - -/*Byte Lane Single-End VREF Select*/ -#undef DDR_PHY_DX0GCR4_DXREFSSEL_DEFVAL -#undef DDR_PHY_DX0GCR4_DXREFSSEL_SHIFT -#undef DDR_PHY_DX0GCR4_DXREFSSEL_MASK -#define DDR_PHY_DX0GCR4_DXREFSSEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_DXREFSSEL_SHIFT 8 -#define DDR_PHY_DX0GCR4_DXREFSSEL_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX0GCR4_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX0GCR4_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX0GCR4_RESERVED_7_6_MASK -#define DDR_PHY_DX0GCR4_RESERVED_7_6_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX0GCR4_RESERVED_7_6_MASK 0x000000C0U - -/*VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX0GCR4_DXREFIEN_DEFVAL -#undef DDR_PHY_DX0GCR4_DXREFIEN_SHIFT -#undef DDR_PHY_DX0GCR4_DXREFIEN_MASK -#define DDR_PHY_DX0GCR4_DXREFIEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_DXREFIEN_SHIFT 2 -#define DDR_PHY_DX0GCR4_DXREFIEN_MASK 0x0000003CU - -/*VRMON control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX0GCR4_DXREFIMON_DEFVAL -#undef DDR_PHY_DX0GCR4_DXREFIMON_SHIFT -#undef DDR_PHY_DX0GCR4_DXREFIMON_MASK -#define DDR_PHY_DX0GCR4_DXREFIMON_DEFVAL 0x0E00003C -#define DDR_PHY_DX0GCR4_DXREFIMON_SHIFT 0 -#define DDR_PHY_DX0GCR4_DXREFIMON_MASK 0x00000003U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX0GCR5_RESERVED_31_DEFVAL -#undef DDR_PHY_DX0GCR5_RESERVED_31_SHIFT -#undef DDR_PHY_DX0GCR5_RESERVED_31_MASK -#define DDR_PHY_DX0GCR5_RESERVED_31_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR5_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX0GCR5_RESERVED_31_MASK 0x80000000U - -/*Byte Lane internal VREF Select for Rank 3*/ -#undef DDR_PHY_DX0GCR5_DXREFISELR3_DEFVAL -#undef DDR_PHY_DX0GCR5_DXREFISELR3_SHIFT -#undef DDR_PHY_DX0GCR5_DXREFISELR3_MASK -#define DDR_PHY_DX0GCR5_DXREFISELR3_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR5_DXREFISELR3_SHIFT 24 -#define DDR_PHY_DX0GCR5_DXREFISELR3_MASK 0x7F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX0GCR5_RESERVED_23_DEFVAL -#undef DDR_PHY_DX0GCR5_RESERVED_23_SHIFT -#undef DDR_PHY_DX0GCR5_RESERVED_23_MASK -#define DDR_PHY_DX0GCR5_RESERVED_23_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR5_RESERVED_23_SHIFT 23 -#define DDR_PHY_DX0GCR5_RESERVED_23_MASK 0x00800000U - -/*Byte Lane internal VREF Select for Rank 2*/ -#undef DDR_PHY_DX0GCR5_DXREFISELR2_DEFVAL -#undef DDR_PHY_DX0GCR5_DXREFISELR2_SHIFT -#undef DDR_PHY_DX0GCR5_DXREFISELR2_MASK -#define DDR_PHY_DX0GCR5_DXREFISELR2_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR5_DXREFISELR2_SHIFT 16 -#define DDR_PHY_DX0GCR5_DXREFISELR2_MASK 0x007F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX0GCR5_RESERVED_15_DEFVAL -#undef DDR_PHY_DX0GCR5_RESERVED_15_SHIFT -#undef DDR_PHY_DX0GCR5_RESERVED_15_MASK -#define DDR_PHY_DX0GCR5_RESERVED_15_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR5_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX0GCR5_RESERVED_15_MASK 0x00008000U - -/*Byte Lane internal VREF Select for Rank 1*/ -#undef DDR_PHY_DX0GCR5_DXREFISELR1_DEFVAL -#undef DDR_PHY_DX0GCR5_DXREFISELR1_SHIFT -#undef DDR_PHY_DX0GCR5_DXREFISELR1_MASK -#define DDR_PHY_DX0GCR5_DXREFISELR1_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR5_DXREFISELR1_SHIFT 8 -#define DDR_PHY_DX0GCR5_DXREFISELR1_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX0GCR5_RESERVED_7_DEFVAL -#undef DDR_PHY_DX0GCR5_RESERVED_7_SHIFT -#undef DDR_PHY_DX0GCR5_RESERVED_7_MASK -#define DDR_PHY_DX0GCR5_RESERVED_7_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR5_RESERVED_7_SHIFT 7 -#define DDR_PHY_DX0GCR5_RESERVED_7_MASK 0x00000080U - -/*Byte Lane internal VREF Select for Rank 0*/ -#undef DDR_PHY_DX0GCR5_DXREFISELR0_DEFVAL -#undef DDR_PHY_DX0GCR5_DXREFISELR0_SHIFT -#undef DDR_PHY_DX0GCR5_DXREFISELR0_MASK -#define DDR_PHY_DX0GCR5_DXREFISELR0_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR5_DXREFISELR0_SHIFT 0 -#define DDR_PHY_DX0GCR5_DXREFISELR0_MASK 0x0000007FU - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX0GCR6_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX0GCR6_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX0GCR6_RESERVED_31_30_MASK -#define DDR_PHY_DX0GCR6_RESERVED_31_30_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR6_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX0GCR6_RESERVED_31_30_MASK 0xC0000000U - -/*DRAM DQ VREF Select for Rank3*/ -#undef DDR_PHY_DX0GCR6_DXDQVREFR3_DEFVAL -#undef DDR_PHY_DX0GCR6_DXDQVREFR3_SHIFT -#undef DDR_PHY_DX0GCR6_DXDQVREFR3_MASK -#define DDR_PHY_DX0GCR6_DXDQVREFR3_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR6_DXDQVREFR3_SHIFT 24 -#define DDR_PHY_DX0GCR6_DXDQVREFR3_MASK 0x3F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX0GCR6_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX0GCR6_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX0GCR6_RESERVED_23_22_MASK -#define DDR_PHY_DX0GCR6_RESERVED_23_22_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR6_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX0GCR6_RESERVED_23_22_MASK 0x00C00000U - -/*DRAM DQ VREF Select for Rank2*/ -#undef DDR_PHY_DX0GCR6_DXDQVREFR2_DEFVAL -#undef DDR_PHY_DX0GCR6_DXDQVREFR2_SHIFT -#undef DDR_PHY_DX0GCR6_DXDQVREFR2_MASK -#define DDR_PHY_DX0GCR6_DXDQVREFR2_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR6_DXDQVREFR2_SHIFT 16 -#define DDR_PHY_DX0GCR6_DXDQVREFR2_MASK 0x003F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX0GCR6_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DX0GCR6_RESERVED_15_14_SHIFT -#undef DDR_PHY_DX0GCR6_RESERVED_15_14_MASK -#define DDR_PHY_DX0GCR6_RESERVED_15_14_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR6_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DX0GCR6_RESERVED_15_14_MASK 0x0000C000U - -/*DRAM DQ VREF Select for Rank1*/ -#undef DDR_PHY_DX0GCR6_DXDQVREFR1_DEFVAL -#undef DDR_PHY_DX0GCR6_DXDQVREFR1_SHIFT -#undef DDR_PHY_DX0GCR6_DXDQVREFR1_MASK -#define DDR_PHY_DX0GCR6_DXDQVREFR1_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR6_DXDQVREFR1_SHIFT 8 -#define DDR_PHY_DX0GCR6_DXDQVREFR1_MASK 0x00003F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX0GCR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX0GCR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX0GCR6_RESERVED_7_6_MASK -#define DDR_PHY_DX0GCR6_RESERVED_7_6_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX0GCR6_RESERVED_7_6_MASK 0x000000C0U - -/*DRAM DQ VREF Select for Rank0*/ -#undef DDR_PHY_DX0GCR6_DXDQVREFR0_DEFVAL -#undef DDR_PHY_DX0GCR6_DXDQVREFR0_SHIFT -#undef DDR_PHY_DX0GCR6_DXDQVREFR0_MASK -#define DDR_PHY_DX0GCR6_DXDQVREFR0_DEFVAL 0x09090909 -#define DDR_PHY_DX0GCR6_DXDQVREFR0_SHIFT 0 -#define DDR_PHY_DX0GCR6_DXDQVREFR0_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX0LCDLR2_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX0LCDLR2_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX0LCDLR2_RESERVED_31_25_MASK -#define DDR_PHY_DX0LCDLR2_RESERVED_31_25_DEFVAL 0x00000000 -#define DDR_PHY_DX0LCDLR2_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX0LCDLR2_RESERVED_31_25_MASK 0xFE000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX0LCDLR2_RESERVED_24_16_DEFVAL -#undef DDR_PHY_DX0LCDLR2_RESERVED_24_16_SHIFT -#undef DDR_PHY_DX0LCDLR2_RESERVED_24_16_MASK -#define DDR_PHY_DX0LCDLR2_RESERVED_24_16_DEFVAL 0x00000000 -#define DDR_PHY_DX0LCDLR2_RESERVED_24_16_SHIFT 16 -#define DDR_PHY_DX0LCDLR2_RESERVED_24_16_MASK 0x01FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX0LCDLR2_RESERVED_15_9_DEFVAL -#undef DDR_PHY_DX0LCDLR2_RESERVED_15_9_SHIFT -#undef DDR_PHY_DX0LCDLR2_RESERVED_15_9_MASK -#define DDR_PHY_DX0LCDLR2_RESERVED_15_9_DEFVAL 0x00000000 -#define DDR_PHY_DX0LCDLR2_RESERVED_15_9_SHIFT 9 -#define DDR_PHY_DX0LCDLR2_RESERVED_15_9_MASK 0x0000FE00U - -/*Read DQS Gating Delay*/ -#undef DDR_PHY_DX0LCDLR2_DQSGD_DEFVAL -#undef DDR_PHY_DX0LCDLR2_DQSGD_SHIFT -#undef DDR_PHY_DX0LCDLR2_DQSGD_MASK -#define DDR_PHY_DX0LCDLR2_DQSGD_DEFVAL 0x00000000 -#define DDR_PHY_DX0LCDLR2_DQSGD_SHIFT 0 -#define DDR_PHY_DX0LCDLR2_DQSGD_MASK 0x000001FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX0GTR0_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX0GTR0_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX0GTR0_RESERVED_31_24_MASK -#define DDR_PHY_DX0GTR0_RESERVED_31_24_DEFVAL 0x00020000 -#define DDR_PHY_DX0GTR0_RESERVED_31_24_SHIFT 27 -#define DDR_PHY_DX0GTR0_RESERVED_31_24_MASK 0xF8000000U - -/*DQ Write Path Latency Pipeline*/ -#undef DDR_PHY_DX0GTR0_WDQSL_DEFVAL -#undef DDR_PHY_DX0GTR0_WDQSL_SHIFT -#undef DDR_PHY_DX0GTR0_WDQSL_MASK -#define DDR_PHY_DX0GTR0_WDQSL_DEFVAL 0x00020000 -#define DDR_PHY_DX0GTR0_WDQSL_SHIFT 24 -#define DDR_PHY_DX0GTR0_WDQSL_MASK 0x07000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX0GTR0_RESERVED_23_20_DEFVAL -#undef DDR_PHY_DX0GTR0_RESERVED_23_20_SHIFT -#undef DDR_PHY_DX0GTR0_RESERVED_23_20_MASK -#define DDR_PHY_DX0GTR0_RESERVED_23_20_DEFVAL 0x00020000 -#define DDR_PHY_DX0GTR0_RESERVED_23_20_SHIFT 20 -#define DDR_PHY_DX0GTR0_RESERVED_23_20_MASK 0x00F00000U - -/*Write Leveling System Latency*/ -#undef DDR_PHY_DX0GTR0_WLSL_DEFVAL -#undef DDR_PHY_DX0GTR0_WLSL_SHIFT -#undef DDR_PHY_DX0GTR0_WLSL_MASK -#define DDR_PHY_DX0GTR0_WLSL_DEFVAL 0x00020000 -#define DDR_PHY_DX0GTR0_WLSL_SHIFT 16 -#define DDR_PHY_DX0GTR0_WLSL_MASK 0x000F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX0GTR0_RESERVED_15_13_DEFVAL -#undef DDR_PHY_DX0GTR0_RESERVED_15_13_SHIFT -#undef DDR_PHY_DX0GTR0_RESERVED_15_13_MASK -#define DDR_PHY_DX0GTR0_RESERVED_15_13_DEFVAL 0x00020000 -#define DDR_PHY_DX0GTR0_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_DX0GTR0_RESERVED_15_13_MASK 0x0000E000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX0GTR0_RESERVED_12_8_DEFVAL -#undef DDR_PHY_DX0GTR0_RESERVED_12_8_SHIFT -#undef DDR_PHY_DX0GTR0_RESERVED_12_8_MASK -#define DDR_PHY_DX0GTR0_RESERVED_12_8_DEFVAL 0x00020000 -#define DDR_PHY_DX0GTR0_RESERVED_12_8_SHIFT 8 -#define DDR_PHY_DX0GTR0_RESERVED_12_8_MASK 0x00001F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX0GTR0_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DX0GTR0_RESERVED_7_5_SHIFT -#undef DDR_PHY_DX0GTR0_RESERVED_7_5_MASK -#define DDR_PHY_DX0GTR0_RESERVED_7_5_DEFVAL 0x00020000 -#define DDR_PHY_DX0GTR0_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DX0GTR0_RESERVED_7_5_MASK 0x000000E0U - -/*DQS Gating System Latency*/ -#undef DDR_PHY_DX0GTR0_DGSL_DEFVAL -#undef DDR_PHY_DX0GTR0_DGSL_SHIFT -#undef DDR_PHY_DX0GTR0_DGSL_MASK -#define DDR_PHY_DX0GTR0_DGSL_DEFVAL 0x00020000 -#define DDR_PHY_DX0GTR0_DGSL_SHIFT 0 -#define DDR_PHY_DX0GTR0_DGSL_MASK 0x0000001FU - -/*Calibration Bypass*/ -#undef DDR_PHY_DX1GCR0_CALBYP_DEFVAL -#undef DDR_PHY_DX1GCR0_CALBYP_SHIFT -#undef DDR_PHY_DX1GCR0_CALBYP_MASK -#define DDR_PHY_DX1GCR0_CALBYP_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_CALBYP_SHIFT 31 -#define DDR_PHY_DX1GCR0_CALBYP_MASK 0x80000000U - -/*Master Delay Line Enable*/ -#undef DDR_PHY_DX1GCR0_MDLEN_DEFVAL -#undef DDR_PHY_DX1GCR0_MDLEN_SHIFT -#undef DDR_PHY_DX1GCR0_MDLEN_MASK -#define DDR_PHY_DX1GCR0_MDLEN_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_MDLEN_SHIFT 30 -#define DDR_PHY_DX1GCR0_MDLEN_MASK 0x40000000U - -/*Configurable ODT(TE) Phase Shift*/ -#undef DDR_PHY_DX1GCR0_CODTSHFT_DEFVAL -#undef DDR_PHY_DX1GCR0_CODTSHFT_SHIFT -#undef DDR_PHY_DX1GCR0_CODTSHFT_MASK -#define DDR_PHY_DX1GCR0_CODTSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_CODTSHFT_SHIFT 28 -#define DDR_PHY_DX1GCR0_CODTSHFT_MASK 0x30000000U - -/*DQS Duty Cycle Correction*/ -#undef DDR_PHY_DX1GCR0_DQSDCC_DEFVAL -#undef DDR_PHY_DX1GCR0_DQSDCC_SHIFT -#undef DDR_PHY_DX1GCR0_DQSDCC_MASK -#define DDR_PHY_DX1GCR0_DQSDCC_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_DQSDCC_SHIFT 24 -#define DDR_PHY_DX1GCR0_DQSDCC_MASK 0x0F000000U - -/*Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY*/ -#undef DDR_PHY_DX1GCR0_RDDLY_DEFVAL -#undef DDR_PHY_DX1GCR0_RDDLY_SHIFT -#undef DDR_PHY_DX1GCR0_RDDLY_MASK -#define DDR_PHY_DX1GCR0_RDDLY_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_RDDLY_SHIFT 20 -#define DDR_PHY_DX1GCR0_RDDLY_MASK 0x00F00000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX1GCR0_RESERVED_19_14_DEFVAL -#undef DDR_PHY_DX1GCR0_RESERVED_19_14_SHIFT -#undef DDR_PHY_DX1GCR0_RESERVED_19_14_MASK -#define DDR_PHY_DX1GCR0_RESERVED_19_14_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_RESERVED_19_14_SHIFT 14 -#define DDR_PHY_DX1GCR0_RESERVED_19_14_MASK 0x000FC000U - -/*DQSNSE Power Down Receiver*/ -#undef DDR_PHY_DX1GCR0_DQSNSEPDR_DEFVAL -#undef DDR_PHY_DX1GCR0_DQSNSEPDR_SHIFT -#undef DDR_PHY_DX1GCR0_DQSNSEPDR_MASK -#define DDR_PHY_DX1GCR0_DQSNSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_DQSNSEPDR_SHIFT 13 -#define DDR_PHY_DX1GCR0_DQSNSEPDR_MASK 0x00002000U - -/*DQSSE Power Down Receiver*/ -#undef DDR_PHY_DX1GCR0_DQSSEPDR_DEFVAL -#undef DDR_PHY_DX1GCR0_DQSSEPDR_SHIFT -#undef DDR_PHY_DX1GCR0_DQSSEPDR_MASK -#define DDR_PHY_DX1GCR0_DQSSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_DQSSEPDR_SHIFT 12 -#define DDR_PHY_DX1GCR0_DQSSEPDR_MASK 0x00001000U - -/*RTT On Additive Latency*/ -#undef DDR_PHY_DX1GCR0_RTTOAL_DEFVAL -#undef DDR_PHY_DX1GCR0_RTTOAL_SHIFT -#undef DDR_PHY_DX1GCR0_RTTOAL_MASK -#define DDR_PHY_DX1GCR0_RTTOAL_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_RTTOAL_SHIFT 11 -#define DDR_PHY_DX1GCR0_RTTOAL_MASK 0x00000800U - -/*RTT Output Hold*/ -#undef DDR_PHY_DX1GCR0_RTTOH_DEFVAL -#undef DDR_PHY_DX1GCR0_RTTOH_SHIFT -#undef DDR_PHY_DX1GCR0_RTTOH_MASK -#define DDR_PHY_DX1GCR0_RTTOH_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_RTTOH_SHIFT 9 -#define DDR_PHY_DX1GCR0_RTTOH_MASK 0x00000600U - -/*Configurable PDR Phase Shift*/ -#undef DDR_PHY_DX1GCR0_CPDRSHFT_DEFVAL -#undef DDR_PHY_DX1GCR0_CPDRSHFT_SHIFT -#undef DDR_PHY_DX1GCR0_CPDRSHFT_MASK -#define DDR_PHY_DX1GCR0_CPDRSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_CPDRSHFT_SHIFT 7 -#define DDR_PHY_DX1GCR0_CPDRSHFT_MASK 0x00000180U - -/*DQSR Power Down*/ -#undef DDR_PHY_DX1GCR0_DQSRPD_DEFVAL -#undef DDR_PHY_DX1GCR0_DQSRPD_SHIFT -#undef DDR_PHY_DX1GCR0_DQSRPD_MASK -#define DDR_PHY_DX1GCR0_DQSRPD_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_DQSRPD_SHIFT 6 -#define DDR_PHY_DX1GCR0_DQSRPD_MASK 0x00000040U - -/*DQSG Power Down Receiver*/ -#undef DDR_PHY_DX1GCR0_DQSGPDR_DEFVAL -#undef DDR_PHY_DX1GCR0_DQSGPDR_SHIFT -#undef DDR_PHY_DX1GCR0_DQSGPDR_MASK -#define DDR_PHY_DX1GCR0_DQSGPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_DQSGPDR_SHIFT 5 -#define DDR_PHY_DX1GCR0_DQSGPDR_MASK 0x00000020U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX1GCR0_RESERVED_4_DEFVAL -#undef DDR_PHY_DX1GCR0_RESERVED_4_SHIFT -#undef DDR_PHY_DX1GCR0_RESERVED_4_MASK -#define DDR_PHY_DX1GCR0_RESERVED_4_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_RESERVED_4_SHIFT 4 -#define DDR_PHY_DX1GCR0_RESERVED_4_MASK 0x00000010U - -/*DQSG On-Die Termination*/ -#undef DDR_PHY_DX1GCR0_DQSGODT_DEFVAL -#undef DDR_PHY_DX1GCR0_DQSGODT_SHIFT -#undef DDR_PHY_DX1GCR0_DQSGODT_MASK -#define DDR_PHY_DX1GCR0_DQSGODT_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_DQSGODT_SHIFT 3 -#define DDR_PHY_DX1GCR0_DQSGODT_MASK 0x00000008U - -/*DQSG Output Enable*/ -#undef DDR_PHY_DX1GCR0_DQSGOE_DEFVAL -#undef DDR_PHY_DX1GCR0_DQSGOE_SHIFT -#undef DDR_PHY_DX1GCR0_DQSGOE_MASK -#define DDR_PHY_DX1GCR0_DQSGOE_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_DQSGOE_SHIFT 2 -#define DDR_PHY_DX1GCR0_DQSGOE_MASK 0x00000004U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX1GCR0_RESERVED_1_0_DEFVAL -#undef DDR_PHY_DX1GCR0_RESERVED_1_0_SHIFT -#undef DDR_PHY_DX1GCR0_RESERVED_1_0_MASK -#define DDR_PHY_DX1GCR0_RESERVED_1_0_DEFVAL 0x40200204 -#define DDR_PHY_DX1GCR0_RESERVED_1_0_SHIFT 0 -#define DDR_PHY_DX1GCR0_RESERVED_1_0_MASK 0x00000003U - -/*Byte lane VREF IOM (Used only by D4MU IOs)*/ -#undef DDR_PHY_DX1GCR4_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DX1GCR4_RESERVED_31_29_SHIFT -#undef DDR_PHY_DX1GCR4_RESERVED_31_29_MASK -#define DDR_PHY_DX1GCR4_RESERVED_31_29_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DX1GCR4_RESERVED_31_29_MASK 0xE0000000U - -/*Byte Lane VREF Pad Enable*/ -#undef DDR_PHY_DX1GCR4_DXREFPEN_DEFVAL -#undef DDR_PHY_DX1GCR4_DXREFPEN_SHIFT -#undef DDR_PHY_DX1GCR4_DXREFPEN_MASK -#define DDR_PHY_DX1GCR4_DXREFPEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_DXREFPEN_SHIFT 28 -#define DDR_PHY_DX1GCR4_DXREFPEN_MASK 0x10000000U - -/*Byte Lane Internal VREF Enable*/ -#undef DDR_PHY_DX1GCR4_DXREFEEN_DEFVAL -#undef DDR_PHY_DX1GCR4_DXREFEEN_SHIFT -#undef DDR_PHY_DX1GCR4_DXREFEEN_MASK -#define DDR_PHY_DX1GCR4_DXREFEEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_DXREFEEN_SHIFT 26 -#define DDR_PHY_DX1GCR4_DXREFEEN_MASK 0x0C000000U - -/*Byte Lane Single-End VREF Enable*/ -#undef DDR_PHY_DX1GCR4_DXREFSEN_DEFVAL -#undef DDR_PHY_DX1GCR4_DXREFSEN_SHIFT -#undef DDR_PHY_DX1GCR4_DXREFSEN_MASK -#define DDR_PHY_DX1GCR4_DXREFSEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_DXREFSEN_SHIFT 25 -#define DDR_PHY_DX1GCR4_DXREFSEN_MASK 0x02000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX1GCR4_RESERVED_24_DEFVAL -#undef DDR_PHY_DX1GCR4_RESERVED_24_SHIFT -#undef DDR_PHY_DX1GCR4_RESERVED_24_MASK -#define DDR_PHY_DX1GCR4_RESERVED_24_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_RESERVED_24_SHIFT 24 -#define DDR_PHY_DX1GCR4_RESERVED_24_MASK 0x01000000U - -/*External VREF generator REFSEL range select*/ -#undef DDR_PHY_DX1GCR4_DXREFESELRANGE_DEFVAL -#undef DDR_PHY_DX1GCR4_DXREFESELRANGE_SHIFT -#undef DDR_PHY_DX1GCR4_DXREFESELRANGE_MASK -#define DDR_PHY_DX1GCR4_DXREFESELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_DXREFESELRANGE_SHIFT 23 -#define DDR_PHY_DX1GCR4_DXREFESELRANGE_MASK 0x00800000U - -/*Byte Lane External VREF Select*/ -#undef DDR_PHY_DX1GCR4_DXREFESEL_DEFVAL -#undef DDR_PHY_DX1GCR4_DXREFESEL_SHIFT -#undef DDR_PHY_DX1GCR4_DXREFESEL_MASK -#define DDR_PHY_DX1GCR4_DXREFESEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_DXREFESEL_SHIFT 16 -#define DDR_PHY_DX1GCR4_DXREFESEL_MASK 0x007F0000U - -/*Single ended VREF generator REFSEL range select*/ -#undef DDR_PHY_DX1GCR4_DXREFSSELRANGE_DEFVAL -#undef DDR_PHY_DX1GCR4_DXREFSSELRANGE_SHIFT -#undef DDR_PHY_DX1GCR4_DXREFSSELRANGE_MASK -#define DDR_PHY_DX1GCR4_DXREFSSELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_DXREFSSELRANGE_SHIFT 15 -#define DDR_PHY_DX1GCR4_DXREFSSELRANGE_MASK 0x00008000U - -/*Byte Lane Single-End VREF Select*/ -#undef DDR_PHY_DX1GCR4_DXREFSSEL_DEFVAL -#undef DDR_PHY_DX1GCR4_DXREFSSEL_SHIFT -#undef DDR_PHY_DX1GCR4_DXREFSSEL_MASK -#define DDR_PHY_DX1GCR4_DXREFSSEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_DXREFSSEL_SHIFT 8 -#define DDR_PHY_DX1GCR4_DXREFSSEL_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX1GCR4_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX1GCR4_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX1GCR4_RESERVED_7_6_MASK -#define DDR_PHY_DX1GCR4_RESERVED_7_6_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX1GCR4_RESERVED_7_6_MASK 0x000000C0U - -/*VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX1GCR4_DXREFIEN_DEFVAL -#undef DDR_PHY_DX1GCR4_DXREFIEN_SHIFT -#undef DDR_PHY_DX1GCR4_DXREFIEN_MASK -#define DDR_PHY_DX1GCR4_DXREFIEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_DXREFIEN_SHIFT 2 -#define DDR_PHY_DX1GCR4_DXREFIEN_MASK 0x0000003CU - -/*VRMON control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX1GCR4_DXREFIMON_DEFVAL -#undef DDR_PHY_DX1GCR4_DXREFIMON_SHIFT -#undef DDR_PHY_DX1GCR4_DXREFIMON_MASK -#define DDR_PHY_DX1GCR4_DXREFIMON_DEFVAL 0x0E00003C -#define DDR_PHY_DX1GCR4_DXREFIMON_SHIFT 0 -#define DDR_PHY_DX1GCR4_DXREFIMON_MASK 0x00000003U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX1GCR5_RESERVED_31_DEFVAL -#undef DDR_PHY_DX1GCR5_RESERVED_31_SHIFT -#undef DDR_PHY_DX1GCR5_RESERVED_31_MASK -#define DDR_PHY_DX1GCR5_RESERVED_31_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR5_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX1GCR5_RESERVED_31_MASK 0x80000000U - -/*Byte Lane internal VREF Select for Rank 3*/ -#undef DDR_PHY_DX1GCR5_DXREFISELR3_DEFVAL -#undef DDR_PHY_DX1GCR5_DXREFISELR3_SHIFT -#undef DDR_PHY_DX1GCR5_DXREFISELR3_MASK -#define DDR_PHY_DX1GCR5_DXREFISELR3_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR5_DXREFISELR3_SHIFT 24 -#define DDR_PHY_DX1GCR5_DXREFISELR3_MASK 0x7F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX1GCR5_RESERVED_23_DEFVAL -#undef DDR_PHY_DX1GCR5_RESERVED_23_SHIFT -#undef DDR_PHY_DX1GCR5_RESERVED_23_MASK -#define DDR_PHY_DX1GCR5_RESERVED_23_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR5_RESERVED_23_SHIFT 23 -#define DDR_PHY_DX1GCR5_RESERVED_23_MASK 0x00800000U - -/*Byte Lane internal VREF Select for Rank 2*/ -#undef DDR_PHY_DX1GCR5_DXREFISELR2_DEFVAL -#undef DDR_PHY_DX1GCR5_DXREFISELR2_SHIFT -#undef DDR_PHY_DX1GCR5_DXREFISELR2_MASK -#define DDR_PHY_DX1GCR5_DXREFISELR2_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR5_DXREFISELR2_SHIFT 16 -#define DDR_PHY_DX1GCR5_DXREFISELR2_MASK 0x007F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX1GCR5_RESERVED_15_DEFVAL -#undef DDR_PHY_DX1GCR5_RESERVED_15_SHIFT -#undef DDR_PHY_DX1GCR5_RESERVED_15_MASK -#define DDR_PHY_DX1GCR5_RESERVED_15_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR5_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX1GCR5_RESERVED_15_MASK 0x00008000U - -/*Byte Lane internal VREF Select for Rank 1*/ -#undef DDR_PHY_DX1GCR5_DXREFISELR1_DEFVAL -#undef DDR_PHY_DX1GCR5_DXREFISELR1_SHIFT -#undef DDR_PHY_DX1GCR5_DXREFISELR1_MASK -#define DDR_PHY_DX1GCR5_DXREFISELR1_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR5_DXREFISELR1_SHIFT 8 -#define DDR_PHY_DX1GCR5_DXREFISELR1_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX1GCR5_RESERVED_7_DEFVAL -#undef DDR_PHY_DX1GCR5_RESERVED_7_SHIFT -#undef DDR_PHY_DX1GCR5_RESERVED_7_MASK -#define DDR_PHY_DX1GCR5_RESERVED_7_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR5_RESERVED_7_SHIFT 7 -#define DDR_PHY_DX1GCR5_RESERVED_7_MASK 0x00000080U - -/*Byte Lane internal VREF Select for Rank 0*/ -#undef DDR_PHY_DX1GCR5_DXREFISELR0_DEFVAL -#undef DDR_PHY_DX1GCR5_DXREFISELR0_SHIFT -#undef DDR_PHY_DX1GCR5_DXREFISELR0_MASK -#define DDR_PHY_DX1GCR5_DXREFISELR0_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR5_DXREFISELR0_SHIFT 0 -#define DDR_PHY_DX1GCR5_DXREFISELR0_MASK 0x0000007FU - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX1GCR6_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX1GCR6_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX1GCR6_RESERVED_31_30_MASK -#define DDR_PHY_DX1GCR6_RESERVED_31_30_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR6_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX1GCR6_RESERVED_31_30_MASK 0xC0000000U - -/*DRAM DQ VREF Select for Rank3*/ -#undef DDR_PHY_DX1GCR6_DXDQVREFR3_DEFVAL -#undef DDR_PHY_DX1GCR6_DXDQVREFR3_SHIFT -#undef DDR_PHY_DX1GCR6_DXDQVREFR3_MASK -#define DDR_PHY_DX1GCR6_DXDQVREFR3_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR6_DXDQVREFR3_SHIFT 24 -#define DDR_PHY_DX1GCR6_DXDQVREFR3_MASK 0x3F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX1GCR6_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX1GCR6_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX1GCR6_RESERVED_23_22_MASK -#define DDR_PHY_DX1GCR6_RESERVED_23_22_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR6_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX1GCR6_RESERVED_23_22_MASK 0x00C00000U - -/*DRAM DQ VREF Select for Rank2*/ -#undef DDR_PHY_DX1GCR6_DXDQVREFR2_DEFVAL -#undef DDR_PHY_DX1GCR6_DXDQVREFR2_SHIFT -#undef DDR_PHY_DX1GCR6_DXDQVREFR2_MASK -#define DDR_PHY_DX1GCR6_DXDQVREFR2_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR6_DXDQVREFR2_SHIFT 16 -#define DDR_PHY_DX1GCR6_DXDQVREFR2_MASK 0x003F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX1GCR6_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DX1GCR6_RESERVED_15_14_SHIFT -#undef DDR_PHY_DX1GCR6_RESERVED_15_14_MASK -#define DDR_PHY_DX1GCR6_RESERVED_15_14_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR6_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DX1GCR6_RESERVED_15_14_MASK 0x0000C000U - -/*DRAM DQ VREF Select for Rank1*/ -#undef DDR_PHY_DX1GCR6_DXDQVREFR1_DEFVAL -#undef DDR_PHY_DX1GCR6_DXDQVREFR1_SHIFT -#undef DDR_PHY_DX1GCR6_DXDQVREFR1_MASK -#define DDR_PHY_DX1GCR6_DXDQVREFR1_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR6_DXDQVREFR1_SHIFT 8 -#define DDR_PHY_DX1GCR6_DXDQVREFR1_MASK 0x00003F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX1GCR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX1GCR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX1GCR6_RESERVED_7_6_MASK -#define DDR_PHY_DX1GCR6_RESERVED_7_6_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX1GCR6_RESERVED_7_6_MASK 0x000000C0U - -/*DRAM DQ VREF Select for Rank0*/ -#undef DDR_PHY_DX1GCR6_DXDQVREFR0_DEFVAL -#undef DDR_PHY_DX1GCR6_DXDQVREFR0_SHIFT -#undef DDR_PHY_DX1GCR6_DXDQVREFR0_MASK -#define DDR_PHY_DX1GCR6_DXDQVREFR0_DEFVAL 0x09090909 -#define DDR_PHY_DX1GCR6_DXDQVREFR0_SHIFT 0 -#define DDR_PHY_DX1GCR6_DXDQVREFR0_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX1LCDLR2_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX1LCDLR2_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX1LCDLR2_RESERVED_31_25_MASK -#define DDR_PHY_DX1LCDLR2_RESERVED_31_25_DEFVAL 0x00000000 -#define DDR_PHY_DX1LCDLR2_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX1LCDLR2_RESERVED_31_25_MASK 0xFE000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX1LCDLR2_RESERVED_24_16_DEFVAL -#undef DDR_PHY_DX1LCDLR2_RESERVED_24_16_SHIFT -#undef DDR_PHY_DX1LCDLR2_RESERVED_24_16_MASK -#define DDR_PHY_DX1LCDLR2_RESERVED_24_16_DEFVAL 0x00000000 -#define DDR_PHY_DX1LCDLR2_RESERVED_24_16_SHIFT 16 -#define DDR_PHY_DX1LCDLR2_RESERVED_24_16_MASK 0x01FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX1LCDLR2_RESERVED_15_9_DEFVAL -#undef DDR_PHY_DX1LCDLR2_RESERVED_15_9_SHIFT -#undef DDR_PHY_DX1LCDLR2_RESERVED_15_9_MASK -#define DDR_PHY_DX1LCDLR2_RESERVED_15_9_DEFVAL 0x00000000 -#define DDR_PHY_DX1LCDLR2_RESERVED_15_9_SHIFT 9 -#define DDR_PHY_DX1LCDLR2_RESERVED_15_9_MASK 0x0000FE00U - -/*Read DQS Gating Delay*/ -#undef DDR_PHY_DX1LCDLR2_DQSGD_DEFVAL -#undef DDR_PHY_DX1LCDLR2_DQSGD_SHIFT -#undef DDR_PHY_DX1LCDLR2_DQSGD_MASK -#define DDR_PHY_DX1LCDLR2_DQSGD_DEFVAL 0x00000000 -#define DDR_PHY_DX1LCDLR2_DQSGD_SHIFT 0 -#define DDR_PHY_DX1LCDLR2_DQSGD_MASK 0x000001FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX1GTR0_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX1GTR0_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX1GTR0_RESERVED_31_24_MASK -#define DDR_PHY_DX1GTR0_RESERVED_31_24_DEFVAL 0x00020000 -#define DDR_PHY_DX1GTR0_RESERVED_31_24_SHIFT 27 -#define DDR_PHY_DX1GTR0_RESERVED_31_24_MASK 0xF8000000U - -/*DQ Write Path Latency Pipeline*/ -#undef DDR_PHY_DX1GTR0_WDQSL_DEFVAL -#undef DDR_PHY_DX1GTR0_WDQSL_SHIFT -#undef DDR_PHY_DX1GTR0_WDQSL_MASK -#define DDR_PHY_DX1GTR0_WDQSL_DEFVAL 0x00020000 -#define DDR_PHY_DX1GTR0_WDQSL_SHIFT 24 -#define DDR_PHY_DX1GTR0_WDQSL_MASK 0x07000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX1GTR0_RESERVED_23_20_DEFVAL -#undef DDR_PHY_DX1GTR0_RESERVED_23_20_SHIFT -#undef DDR_PHY_DX1GTR0_RESERVED_23_20_MASK -#define DDR_PHY_DX1GTR0_RESERVED_23_20_DEFVAL 0x00020000 -#define DDR_PHY_DX1GTR0_RESERVED_23_20_SHIFT 20 -#define DDR_PHY_DX1GTR0_RESERVED_23_20_MASK 0x00F00000U - -/*Write Leveling System Latency*/ -#undef DDR_PHY_DX1GTR0_WLSL_DEFVAL -#undef DDR_PHY_DX1GTR0_WLSL_SHIFT -#undef DDR_PHY_DX1GTR0_WLSL_MASK -#define DDR_PHY_DX1GTR0_WLSL_DEFVAL 0x00020000 -#define DDR_PHY_DX1GTR0_WLSL_SHIFT 16 -#define DDR_PHY_DX1GTR0_WLSL_MASK 0x000F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX1GTR0_RESERVED_15_13_DEFVAL -#undef DDR_PHY_DX1GTR0_RESERVED_15_13_SHIFT -#undef DDR_PHY_DX1GTR0_RESERVED_15_13_MASK -#define DDR_PHY_DX1GTR0_RESERVED_15_13_DEFVAL 0x00020000 -#define DDR_PHY_DX1GTR0_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_DX1GTR0_RESERVED_15_13_MASK 0x0000E000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX1GTR0_RESERVED_12_8_DEFVAL -#undef DDR_PHY_DX1GTR0_RESERVED_12_8_SHIFT -#undef DDR_PHY_DX1GTR0_RESERVED_12_8_MASK -#define DDR_PHY_DX1GTR0_RESERVED_12_8_DEFVAL 0x00020000 -#define DDR_PHY_DX1GTR0_RESERVED_12_8_SHIFT 8 -#define DDR_PHY_DX1GTR0_RESERVED_12_8_MASK 0x00001F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX1GTR0_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DX1GTR0_RESERVED_7_5_SHIFT -#undef DDR_PHY_DX1GTR0_RESERVED_7_5_MASK -#define DDR_PHY_DX1GTR0_RESERVED_7_5_DEFVAL 0x00020000 -#define DDR_PHY_DX1GTR0_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DX1GTR0_RESERVED_7_5_MASK 0x000000E0U - -/*DQS Gating System Latency*/ -#undef DDR_PHY_DX1GTR0_DGSL_DEFVAL -#undef DDR_PHY_DX1GTR0_DGSL_SHIFT -#undef DDR_PHY_DX1GTR0_DGSL_MASK -#define DDR_PHY_DX1GTR0_DGSL_DEFVAL 0x00020000 -#define DDR_PHY_DX1GTR0_DGSL_SHIFT 0 -#define DDR_PHY_DX1GTR0_DGSL_MASK 0x0000001FU - -/*Calibration Bypass*/ -#undef DDR_PHY_DX2GCR0_CALBYP_DEFVAL -#undef DDR_PHY_DX2GCR0_CALBYP_SHIFT -#undef DDR_PHY_DX2GCR0_CALBYP_MASK -#define DDR_PHY_DX2GCR0_CALBYP_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_CALBYP_SHIFT 31 -#define DDR_PHY_DX2GCR0_CALBYP_MASK 0x80000000U - -/*Master Delay Line Enable*/ -#undef DDR_PHY_DX2GCR0_MDLEN_DEFVAL -#undef DDR_PHY_DX2GCR0_MDLEN_SHIFT -#undef DDR_PHY_DX2GCR0_MDLEN_MASK -#define DDR_PHY_DX2GCR0_MDLEN_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_MDLEN_SHIFT 30 -#define DDR_PHY_DX2GCR0_MDLEN_MASK 0x40000000U - -/*Configurable ODT(TE) Phase Shift*/ -#undef DDR_PHY_DX2GCR0_CODTSHFT_DEFVAL -#undef DDR_PHY_DX2GCR0_CODTSHFT_SHIFT -#undef DDR_PHY_DX2GCR0_CODTSHFT_MASK -#define DDR_PHY_DX2GCR0_CODTSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_CODTSHFT_SHIFT 28 -#define DDR_PHY_DX2GCR0_CODTSHFT_MASK 0x30000000U - -/*DQS Duty Cycle Correction*/ -#undef DDR_PHY_DX2GCR0_DQSDCC_DEFVAL -#undef DDR_PHY_DX2GCR0_DQSDCC_SHIFT -#undef DDR_PHY_DX2GCR0_DQSDCC_MASK -#define DDR_PHY_DX2GCR0_DQSDCC_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_DQSDCC_SHIFT 24 -#define DDR_PHY_DX2GCR0_DQSDCC_MASK 0x0F000000U - -/*Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY*/ -#undef DDR_PHY_DX2GCR0_RDDLY_DEFVAL -#undef DDR_PHY_DX2GCR0_RDDLY_SHIFT -#undef DDR_PHY_DX2GCR0_RDDLY_MASK -#define DDR_PHY_DX2GCR0_RDDLY_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_RDDLY_SHIFT 20 -#define DDR_PHY_DX2GCR0_RDDLY_MASK 0x00F00000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX2GCR0_RESERVED_19_14_DEFVAL -#undef DDR_PHY_DX2GCR0_RESERVED_19_14_SHIFT -#undef DDR_PHY_DX2GCR0_RESERVED_19_14_MASK -#define DDR_PHY_DX2GCR0_RESERVED_19_14_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_RESERVED_19_14_SHIFT 14 -#define DDR_PHY_DX2GCR0_RESERVED_19_14_MASK 0x000FC000U - -/*DQSNSE Power Down Receiver*/ -#undef DDR_PHY_DX2GCR0_DQSNSEPDR_DEFVAL -#undef DDR_PHY_DX2GCR0_DQSNSEPDR_SHIFT -#undef DDR_PHY_DX2GCR0_DQSNSEPDR_MASK -#define DDR_PHY_DX2GCR0_DQSNSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_DQSNSEPDR_SHIFT 13 -#define DDR_PHY_DX2GCR0_DQSNSEPDR_MASK 0x00002000U - -/*DQSSE Power Down Receiver*/ -#undef DDR_PHY_DX2GCR0_DQSSEPDR_DEFVAL -#undef DDR_PHY_DX2GCR0_DQSSEPDR_SHIFT -#undef DDR_PHY_DX2GCR0_DQSSEPDR_MASK -#define DDR_PHY_DX2GCR0_DQSSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_DQSSEPDR_SHIFT 12 -#define DDR_PHY_DX2GCR0_DQSSEPDR_MASK 0x00001000U - -/*RTT On Additive Latency*/ -#undef DDR_PHY_DX2GCR0_RTTOAL_DEFVAL -#undef DDR_PHY_DX2GCR0_RTTOAL_SHIFT -#undef DDR_PHY_DX2GCR0_RTTOAL_MASK -#define DDR_PHY_DX2GCR0_RTTOAL_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_RTTOAL_SHIFT 11 -#define DDR_PHY_DX2GCR0_RTTOAL_MASK 0x00000800U - -/*RTT Output Hold*/ -#undef DDR_PHY_DX2GCR0_RTTOH_DEFVAL -#undef DDR_PHY_DX2GCR0_RTTOH_SHIFT -#undef DDR_PHY_DX2GCR0_RTTOH_MASK -#define DDR_PHY_DX2GCR0_RTTOH_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_RTTOH_SHIFT 9 -#define DDR_PHY_DX2GCR0_RTTOH_MASK 0x00000600U - -/*Configurable PDR Phase Shift*/ -#undef DDR_PHY_DX2GCR0_CPDRSHFT_DEFVAL -#undef DDR_PHY_DX2GCR0_CPDRSHFT_SHIFT -#undef DDR_PHY_DX2GCR0_CPDRSHFT_MASK -#define DDR_PHY_DX2GCR0_CPDRSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_CPDRSHFT_SHIFT 7 -#define DDR_PHY_DX2GCR0_CPDRSHFT_MASK 0x00000180U - -/*DQSR Power Down*/ -#undef DDR_PHY_DX2GCR0_DQSRPD_DEFVAL -#undef DDR_PHY_DX2GCR0_DQSRPD_SHIFT -#undef DDR_PHY_DX2GCR0_DQSRPD_MASK -#define DDR_PHY_DX2GCR0_DQSRPD_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_DQSRPD_SHIFT 6 -#define DDR_PHY_DX2GCR0_DQSRPD_MASK 0x00000040U - -/*DQSG Power Down Receiver*/ -#undef DDR_PHY_DX2GCR0_DQSGPDR_DEFVAL -#undef DDR_PHY_DX2GCR0_DQSGPDR_SHIFT -#undef DDR_PHY_DX2GCR0_DQSGPDR_MASK -#define DDR_PHY_DX2GCR0_DQSGPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_DQSGPDR_SHIFT 5 -#define DDR_PHY_DX2GCR0_DQSGPDR_MASK 0x00000020U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX2GCR0_RESERVED_4_DEFVAL -#undef DDR_PHY_DX2GCR0_RESERVED_4_SHIFT -#undef DDR_PHY_DX2GCR0_RESERVED_4_MASK -#define DDR_PHY_DX2GCR0_RESERVED_4_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_RESERVED_4_SHIFT 4 -#define DDR_PHY_DX2GCR0_RESERVED_4_MASK 0x00000010U - -/*DQSG On-Die Termination*/ -#undef DDR_PHY_DX2GCR0_DQSGODT_DEFVAL -#undef DDR_PHY_DX2GCR0_DQSGODT_SHIFT -#undef DDR_PHY_DX2GCR0_DQSGODT_MASK -#define DDR_PHY_DX2GCR0_DQSGODT_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_DQSGODT_SHIFT 3 -#define DDR_PHY_DX2GCR0_DQSGODT_MASK 0x00000008U - -/*DQSG Output Enable*/ -#undef DDR_PHY_DX2GCR0_DQSGOE_DEFVAL -#undef DDR_PHY_DX2GCR0_DQSGOE_SHIFT -#undef DDR_PHY_DX2GCR0_DQSGOE_MASK -#define DDR_PHY_DX2GCR0_DQSGOE_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_DQSGOE_SHIFT 2 -#define DDR_PHY_DX2GCR0_DQSGOE_MASK 0x00000004U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX2GCR0_RESERVED_1_0_DEFVAL -#undef DDR_PHY_DX2GCR0_RESERVED_1_0_SHIFT -#undef DDR_PHY_DX2GCR0_RESERVED_1_0_MASK -#define DDR_PHY_DX2GCR0_RESERVED_1_0_DEFVAL 0x40200204 -#define DDR_PHY_DX2GCR0_RESERVED_1_0_SHIFT 0 -#define DDR_PHY_DX2GCR0_RESERVED_1_0_MASK 0x00000003U - -/*Enables the PDR mode for DQ[7:0]*/ -#undef DDR_PHY_DX2GCR1_DXPDRMODE_DEFVAL -#undef DDR_PHY_DX2GCR1_DXPDRMODE_SHIFT -#undef DDR_PHY_DX2GCR1_DXPDRMODE_MASK -#define DDR_PHY_DX2GCR1_DXPDRMODE_DEFVAL 0x00007FFF -#define DDR_PHY_DX2GCR1_DXPDRMODE_SHIFT 16 -#define DDR_PHY_DX2GCR1_DXPDRMODE_MASK 0xFFFF0000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_DX2GCR1_RESERVED_15_DEFVAL -#undef DDR_PHY_DX2GCR1_RESERVED_15_SHIFT -#undef DDR_PHY_DX2GCR1_RESERVED_15_MASK -#define DDR_PHY_DX2GCR1_RESERVED_15_DEFVAL 0x00007FFF -#define DDR_PHY_DX2GCR1_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX2GCR1_RESERVED_15_MASK 0x00008000U - -/*Select the delayed or non-delayed read data strobe #*/ -#undef DDR_PHY_DX2GCR1_QSNSEL_DEFVAL -#undef DDR_PHY_DX2GCR1_QSNSEL_SHIFT -#undef DDR_PHY_DX2GCR1_QSNSEL_MASK -#define DDR_PHY_DX2GCR1_QSNSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX2GCR1_QSNSEL_SHIFT 14 -#define DDR_PHY_DX2GCR1_QSNSEL_MASK 0x00004000U - -/*Select the delayed or non-delayed read data strobe*/ -#undef DDR_PHY_DX2GCR1_QSSEL_DEFVAL -#undef DDR_PHY_DX2GCR1_QSSEL_SHIFT -#undef DDR_PHY_DX2GCR1_QSSEL_MASK -#define DDR_PHY_DX2GCR1_QSSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX2GCR1_QSSEL_SHIFT 13 -#define DDR_PHY_DX2GCR1_QSSEL_MASK 0x00002000U - -/*Enables Read Data Strobe in a byte lane*/ -#undef DDR_PHY_DX2GCR1_OEEN_DEFVAL -#undef DDR_PHY_DX2GCR1_OEEN_SHIFT -#undef DDR_PHY_DX2GCR1_OEEN_MASK -#define DDR_PHY_DX2GCR1_OEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX2GCR1_OEEN_SHIFT 12 -#define DDR_PHY_DX2GCR1_OEEN_MASK 0x00001000U - -/*Enables PDR in a byte lane*/ -#undef DDR_PHY_DX2GCR1_PDREN_DEFVAL -#undef DDR_PHY_DX2GCR1_PDREN_SHIFT -#undef DDR_PHY_DX2GCR1_PDREN_MASK -#define DDR_PHY_DX2GCR1_PDREN_DEFVAL 0x00007FFF -#define DDR_PHY_DX2GCR1_PDREN_SHIFT 11 -#define DDR_PHY_DX2GCR1_PDREN_MASK 0x00000800U - -/*Enables ODT/TE in a byte lane*/ -#undef DDR_PHY_DX2GCR1_TEEN_DEFVAL -#undef DDR_PHY_DX2GCR1_TEEN_SHIFT -#undef DDR_PHY_DX2GCR1_TEEN_MASK -#define DDR_PHY_DX2GCR1_TEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX2GCR1_TEEN_SHIFT 10 -#define DDR_PHY_DX2GCR1_TEEN_MASK 0x00000400U - -/*Enables Write Data strobe in a byte lane*/ -#undef DDR_PHY_DX2GCR1_DSEN_DEFVAL -#undef DDR_PHY_DX2GCR1_DSEN_SHIFT -#undef DDR_PHY_DX2GCR1_DSEN_MASK -#define DDR_PHY_DX2GCR1_DSEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX2GCR1_DSEN_SHIFT 9 -#define DDR_PHY_DX2GCR1_DSEN_MASK 0x00000200U - -/*Enables DM pin in a byte lane*/ -#undef DDR_PHY_DX2GCR1_DMEN_DEFVAL -#undef DDR_PHY_DX2GCR1_DMEN_SHIFT -#undef DDR_PHY_DX2GCR1_DMEN_MASK -#define DDR_PHY_DX2GCR1_DMEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX2GCR1_DMEN_SHIFT 8 -#define DDR_PHY_DX2GCR1_DMEN_MASK 0x00000100U - -/*Enables DQ corresponding to each bit in a byte*/ -#undef DDR_PHY_DX2GCR1_DQEN_DEFVAL -#undef DDR_PHY_DX2GCR1_DQEN_SHIFT -#undef DDR_PHY_DX2GCR1_DQEN_MASK -#define DDR_PHY_DX2GCR1_DQEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX2GCR1_DQEN_SHIFT 0 -#define DDR_PHY_DX2GCR1_DQEN_MASK 0x000000FFU - -/*Byte lane VREF IOM (Used only by D4MU IOs)*/ -#undef DDR_PHY_DX2GCR4_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DX2GCR4_RESERVED_31_29_SHIFT -#undef DDR_PHY_DX2GCR4_RESERVED_31_29_MASK -#define DDR_PHY_DX2GCR4_RESERVED_31_29_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DX2GCR4_RESERVED_31_29_MASK 0xE0000000U - -/*Byte Lane VREF Pad Enable*/ -#undef DDR_PHY_DX2GCR4_DXREFPEN_DEFVAL -#undef DDR_PHY_DX2GCR4_DXREFPEN_SHIFT -#undef DDR_PHY_DX2GCR4_DXREFPEN_MASK -#define DDR_PHY_DX2GCR4_DXREFPEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_DXREFPEN_SHIFT 28 -#define DDR_PHY_DX2GCR4_DXREFPEN_MASK 0x10000000U - -/*Byte Lane Internal VREF Enable*/ -#undef DDR_PHY_DX2GCR4_DXREFEEN_DEFVAL -#undef DDR_PHY_DX2GCR4_DXREFEEN_SHIFT -#undef DDR_PHY_DX2GCR4_DXREFEEN_MASK -#define DDR_PHY_DX2GCR4_DXREFEEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_DXREFEEN_SHIFT 26 -#define DDR_PHY_DX2GCR4_DXREFEEN_MASK 0x0C000000U - -/*Byte Lane Single-End VREF Enable*/ -#undef DDR_PHY_DX2GCR4_DXREFSEN_DEFVAL -#undef DDR_PHY_DX2GCR4_DXREFSEN_SHIFT -#undef DDR_PHY_DX2GCR4_DXREFSEN_MASK -#define DDR_PHY_DX2GCR4_DXREFSEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_DXREFSEN_SHIFT 25 -#define DDR_PHY_DX2GCR4_DXREFSEN_MASK 0x02000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX2GCR4_RESERVED_24_DEFVAL -#undef DDR_PHY_DX2GCR4_RESERVED_24_SHIFT -#undef DDR_PHY_DX2GCR4_RESERVED_24_MASK -#define DDR_PHY_DX2GCR4_RESERVED_24_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_RESERVED_24_SHIFT 24 -#define DDR_PHY_DX2GCR4_RESERVED_24_MASK 0x01000000U - -/*External VREF generator REFSEL range select*/ -#undef DDR_PHY_DX2GCR4_DXREFESELRANGE_DEFVAL -#undef DDR_PHY_DX2GCR4_DXREFESELRANGE_SHIFT -#undef DDR_PHY_DX2GCR4_DXREFESELRANGE_MASK -#define DDR_PHY_DX2GCR4_DXREFESELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_DXREFESELRANGE_SHIFT 23 -#define DDR_PHY_DX2GCR4_DXREFESELRANGE_MASK 0x00800000U - -/*Byte Lane External VREF Select*/ -#undef DDR_PHY_DX2GCR4_DXREFESEL_DEFVAL -#undef DDR_PHY_DX2GCR4_DXREFESEL_SHIFT -#undef DDR_PHY_DX2GCR4_DXREFESEL_MASK -#define DDR_PHY_DX2GCR4_DXREFESEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_DXREFESEL_SHIFT 16 -#define DDR_PHY_DX2GCR4_DXREFESEL_MASK 0x007F0000U - -/*Single ended VREF generator REFSEL range select*/ -#undef DDR_PHY_DX2GCR4_DXREFSSELRANGE_DEFVAL -#undef DDR_PHY_DX2GCR4_DXREFSSELRANGE_SHIFT -#undef DDR_PHY_DX2GCR4_DXREFSSELRANGE_MASK -#define DDR_PHY_DX2GCR4_DXREFSSELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_DXREFSSELRANGE_SHIFT 15 -#define DDR_PHY_DX2GCR4_DXREFSSELRANGE_MASK 0x00008000U - -/*Byte Lane Single-End VREF Select*/ -#undef DDR_PHY_DX2GCR4_DXREFSSEL_DEFVAL -#undef DDR_PHY_DX2GCR4_DXREFSSEL_SHIFT -#undef DDR_PHY_DX2GCR4_DXREFSSEL_MASK -#define DDR_PHY_DX2GCR4_DXREFSSEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_DXREFSSEL_SHIFT 8 -#define DDR_PHY_DX2GCR4_DXREFSSEL_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX2GCR4_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX2GCR4_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX2GCR4_RESERVED_7_6_MASK -#define DDR_PHY_DX2GCR4_RESERVED_7_6_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX2GCR4_RESERVED_7_6_MASK 0x000000C0U - -/*VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX2GCR4_DXREFIEN_DEFVAL -#undef DDR_PHY_DX2GCR4_DXREFIEN_SHIFT -#undef DDR_PHY_DX2GCR4_DXREFIEN_MASK -#define DDR_PHY_DX2GCR4_DXREFIEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_DXREFIEN_SHIFT 2 -#define DDR_PHY_DX2GCR4_DXREFIEN_MASK 0x0000003CU - -/*VRMON control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX2GCR4_DXREFIMON_DEFVAL -#undef DDR_PHY_DX2GCR4_DXREFIMON_SHIFT -#undef DDR_PHY_DX2GCR4_DXREFIMON_MASK -#define DDR_PHY_DX2GCR4_DXREFIMON_DEFVAL 0x0E00003C -#define DDR_PHY_DX2GCR4_DXREFIMON_SHIFT 0 -#define DDR_PHY_DX2GCR4_DXREFIMON_MASK 0x00000003U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX2GCR5_RESERVED_31_DEFVAL -#undef DDR_PHY_DX2GCR5_RESERVED_31_SHIFT -#undef DDR_PHY_DX2GCR5_RESERVED_31_MASK -#define DDR_PHY_DX2GCR5_RESERVED_31_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR5_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX2GCR5_RESERVED_31_MASK 0x80000000U - -/*Byte Lane internal VREF Select for Rank 3*/ -#undef DDR_PHY_DX2GCR5_DXREFISELR3_DEFVAL -#undef DDR_PHY_DX2GCR5_DXREFISELR3_SHIFT -#undef DDR_PHY_DX2GCR5_DXREFISELR3_MASK -#define DDR_PHY_DX2GCR5_DXREFISELR3_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR5_DXREFISELR3_SHIFT 24 -#define DDR_PHY_DX2GCR5_DXREFISELR3_MASK 0x7F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX2GCR5_RESERVED_23_DEFVAL -#undef DDR_PHY_DX2GCR5_RESERVED_23_SHIFT -#undef DDR_PHY_DX2GCR5_RESERVED_23_MASK -#define DDR_PHY_DX2GCR5_RESERVED_23_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR5_RESERVED_23_SHIFT 23 -#define DDR_PHY_DX2GCR5_RESERVED_23_MASK 0x00800000U - -/*Byte Lane internal VREF Select for Rank 2*/ -#undef DDR_PHY_DX2GCR5_DXREFISELR2_DEFVAL -#undef DDR_PHY_DX2GCR5_DXREFISELR2_SHIFT -#undef DDR_PHY_DX2GCR5_DXREFISELR2_MASK -#define DDR_PHY_DX2GCR5_DXREFISELR2_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR5_DXREFISELR2_SHIFT 16 -#define DDR_PHY_DX2GCR5_DXREFISELR2_MASK 0x007F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX2GCR5_RESERVED_15_DEFVAL -#undef DDR_PHY_DX2GCR5_RESERVED_15_SHIFT -#undef DDR_PHY_DX2GCR5_RESERVED_15_MASK -#define DDR_PHY_DX2GCR5_RESERVED_15_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR5_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX2GCR5_RESERVED_15_MASK 0x00008000U - -/*Byte Lane internal VREF Select for Rank 1*/ -#undef DDR_PHY_DX2GCR5_DXREFISELR1_DEFVAL -#undef DDR_PHY_DX2GCR5_DXREFISELR1_SHIFT -#undef DDR_PHY_DX2GCR5_DXREFISELR1_MASK -#define DDR_PHY_DX2GCR5_DXREFISELR1_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR5_DXREFISELR1_SHIFT 8 -#define DDR_PHY_DX2GCR5_DXREFISELR1_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX2GCR5_RESERVED_7_DEFVAL -#undef DDR_PHY_DX2GCR5_RESERVED_7_SHIFT -#undef DDR_PHY_DX2GCR5_RESERVED_7_MASK -#define DDR_PHY_DX2GCR5_RESERVED_7_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR5_RESERVED_7_SHIFT 7 -#define DDR_PHY_DX2GCR5_RESERVED_7_MASK 0x00000080U - -/*Byte Lane internal VREF Select for Rank 0*/ -#undef DDR_PHY_DX2GCR5_DXREFISELR0_DEFVAL -#undef DDR_PHY_DX2GCR5_DXREFISELR0_SHIFT -#undef DDR_PHY_DX2GCR5_DXREFISELR0_MASK -#define DDR_PHY_DX2GCR5_DXREFISELR0_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR5_DXREFISELR0_SHIFT 0 -#define DDR_PHY_DX2GCR5_DXREFISELR0_MASK 0x0000007FU - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX2GCR6_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX2GCR6_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX2GCR6_RESERVED_31_30_MASK -#define DDR_PHY_DX2GCR6_RESERVED_31_30_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR6_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX2GCR6_RESERVED_31_30_MASK 0xC0000000U - -/*DRAM DQ VREF Select for Rank3*/ -#undef DDR_PHY_DX2GCR6_DXDQVREFR3_DEFVAL -#undef DDR_PHY_DX2GCR6_DXDQVREFR3_SHIFT -#undef DDR_PHY_DX2GCR6_DXDQVREFR3_MASK -#define DDR_PHY_DX2GCR6_DXDQVREFR3_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR6_DXDQVREFR3_SHIFT 24 -#define DDR_PHY_DX2GCR6_DXDQVREFR3_MASK 0x3F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX2GCR6_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX2GCR6_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX2GCR6_RESERVED_23_22_MASK -#define DDR_PHY_DX2GCR6_RESERVED_23_22_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR6_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX2GCR6_RESERVED_23_22_MASK 0x00C00000U - -/*DRAM DQ VREF Select for Rank2*/ -#undef DDR_PHY_DX2GCR6_DXDQVREFR2_DEFVAL -#undef DDR_PHY_DX2GCR6_DXDQVREFR2_SHIFT -#undef DDR_PHY_DX2GCR6_DXDQVREFR2_MASK -#define DDR_PHY_DX2GCR6_DXDQVREFR2_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR6_DXDQVREFR2_SHIFT 16 -#define DDR_PHY_DX2GCR6_DXDQVREFR2_MASK 0x003F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX2GCR6_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DX2GCR6_RESERVED_15_14_SHIFT -#undef DDR_PHY_DX2GCR6_RESERVED_15_14_MASK -#define DDR_PHY_DX2GCR6_RESERVED_15_14_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR6_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DX2GCR6_RESERVED_15_14_MASK 0x0000C000U - -/*DRAM DQ VREF Select for Rank1*/ -#undef DDR_PHY_DX2GCR6_DXDQVREFR1_DEFVAL -#undef DDR_PHY_DX2GCR6_DXDQVREFR1_SHIFT -#undef DDR_PHY_DX2GCR6_DXDQVREFR1_MASK -#define DDR_PHY_DX2GCR6_DXDQVREFR1_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR6_DXDQVREFR1_SHIFT 8 -#define DDR_PHY_DX2GCR6_DXDQVREFR1_MASK 0x00003F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX2GCR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX2GCR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX2GCR6_RESERVED_7_6_MASK -#define DDR_PHY_DX2GCR6_RESERVED_7_6_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX2GCR6_RESERVED_7_6_MASK 0x000000C0U - -/*DRAM DQ VREF Select for Rank0*/ -#undef DDR_PHY_DX2GCR6_DXDQVREFR0_DEFVAL -#undef DDR_PHY_DX2GCR6_DXDQVREFR0_SHIFT -#undef DDR_PHY_DX2GCR6_DXDQVREFR0_MASK -#define DDR_PHY_DX2GCR6_DXDQVREFR0_DEFVAL 0x09090909 -#define DDR_PHY_DX2GCR6_DXDQVREFR0_SHIFT 0 -#define DDR_PHY_DX2GCR6_DXDQVREFR0_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX2LCDLR2_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX2LCDLR2_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX2LCDLR2_RESERVED_31_25_MASK -#define DDR_PHY_DX2LCDLR2_RESERVED_31_25_DEFVAL 0x00000000 -#define DDR_PHY_DX2LCDLR2_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX2LCDLR2_RESERVED_31_25_MASK 0xFE000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX2LCDLR2_RESERVED_24_16_DEFVAL -#undef DDR_PHY_DX2LCDLR2_RESERVED_24_16_SHIFT -#undef DDR_PHY_DX2LCDLR2_RESERVED_24_16_MASK -#define DDR_PHY_DX2LCDLR2_RESERVED_24_16_DEFVAL 0x00000000 -#define DDR_PHY_DX2LCDLR2_RESERVED_24_16_SHIFT 16 -#define DDR_PHY_DX2LCDLR2_RESERVED_24_16_MASK 0x01FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX2LCDLR2_RESERVED_15_9_DEFVAL -#undef DDR_PHY_DX2LCDLR2_RESERVED_15_9_SHIFT -#undef DDR_PHY_DX2LCDLR2_RESERVED_15_9_MASK -#define DDR_PHY_DX2LCDLR2_RESERVED_15_9_DEFVAL 0x00000000 -#define DDR_PHY_DX2LCDLR2_RESERVED_15_9_SHIFT 9 -#define DDR_PHY_DX2LCDLR2_RESERVED_15_9_MASK 0x0000FE00U - -/*Read DQS Gating Delay*/ -#undef DDR_PHY_DX2LCDLR2_DQSGD_DEFVAL -#undef DDR_PHY_DX2LCDLR2_DQSGD_SHIFT -#undef DDR_PHY_DX2LCDLR2_DQSGD_MASK -#define DDR_PHY_DX2LCDLR2_DQSGD_DEFVAL 0x00000000 -#define DDR_PHY_DX2LCDLR2_DQSGD_SHIFT 0 -#define DDR_PHY_DX2LCDLR2_DQSGD_MASK 0x000001FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX2GTR0_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX2GTR0_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX2GTR0_RESERVED_31_24_MASK -#define DDR_PHY_DX2GTR0_RESERVED_31_24_DEFVAL 0x00020000 -#define DDR_PHY_DX2GTR0_RESERVED_31_24_SHIFT 27 -#define DDR_PHY_DX2GTR0_RESERVED_31_24_MASK 0xF8000000U - -/*DQ Write Path Latency Pipeline*/ -#undef DDR_PHY_DX2GTR0_WDQSL_DEFVAL -#undef DDR_PHY_DX2GTR0_WDQSL_SHIFT -#undef DDR_PHY_DX2GTR0_WDQSL_MASK -#define DDR_PHY_DX2GTR0_WDQSL_DEFVAL 0x00020000 -#define DDR_PHY_DX2GTR0_WDQSL_SHIFT 24 -#define DDR_PHY_DX2GTR0_WDQSL_MASK 0x07000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX2GTR0_RESERVED_23_20_DEFVAL -#undef DDR_PHY_DX2GTR0_RESERVED_23_20_SHIFT -#undef DDR_PHY_DX2GTR0_RESERVED_23_20_MASK -#define DDR_PHY_DX2GTR0_RESERVED_23_20_DEFVAL 0x00020000 -#define DDR_PHY_DX2GTR0_RESERVED_23_20_SHIFT 20 -#define DDR_PHY_DX2GTR0_RESERVED_23_20_MASK 0x00F00000U - -/*Write Leveling System Latency*/ -#undef DDR_PHY_DX2GTR0_WLSL_DEFVAL -#undef DDR_PHY_DX2GTR0_WLSL_SHIFT -#undef DDR_PHY_DX2GTR0_WLSL_MASK -#define DDR_PHY_DX2GTR0_WLSL_DEFVAL 0x00020000 -#define DDR_PHY_DX2GTR0_WLSL_SHIFT 16 -#define DDR_PHY_DX2GTR0_WLSL_MASK 0x000F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX2GTR0_RESERVED_15_13_DEFVAL -#undef DDR_PHY_DX2GTR0_RESERVED_15_13_SHIFT -#undef DDR_PHY_DX2GTR0_RESERVED_15_13_MASK -#define DDR_PHY_DX2GTR0_RESERVED_15_13_DEFVAL 0x00020000 -#define DDR_PHY_DX2GTR0_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_DX2GTR0_RESERVED_15_13_MASK 0x0000E000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX2GTR0_RESERVED_12_8_DEFVAL -#undef DDR_PHY_DX2GTR0_RESERVED_12_8_SHIFT -#undef DDR_PHY_DX2GTR0_RESERVED_12_8_MASK -#define DDR_PHY_DX2GTR0_RESERVED_12_8_DEFVAL 0x00020000 -#define DDR_PHY_DX2GTR0_RESERVED_12_8_SHIFT 8 -#define DDR_PHY_DX2GTR0_RESERVED_12_8_MASK 0x00001F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX2GTR0_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DX2GTR0_RESERVED_7_5_SHIFT -#undef DDR_PHY_DX2GTR0_RESERVED_7_5_MASK -#define DDR_PHY_DX2GTR0_RESERVED_7_5_DEFVAL 0x00020000 -#define DDR_PHY_DX2GTR0_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DX2GTR0_RESERVED_7_5_MASK 0x000000E0U - -/*DQS Gating System Latency*/ -#undef DDR_PHY_DX2GTR0_DGSL_DEFVAL -#undef DDR_PHY_DX2GTR0_DGSL_SHIFT -#undef DDR_PHY_DX2GTR0_DGSL_MASK -#define DDR_PHY_DX2GTR0_DGSL_DEFVAL 0x00020000 -#define DDR_PHY_DX2GTR0_DGSL_SHIFT 0 -#define DDR_PHY_DX2GTR0_DGSL_MASK 0x0000001FU - -/*Calibration Bypass*/ -#undef DDR_PHY_DX3GCR0_CALBYP_DEFVAL -#undef DDR_PHY_DX3GCR0_CALBYP_SHIFT -#undef DDR_PHY_DX3GCR0_CALBYP_MASK -#define DDR_PHY_DX3GCR0_CALBYP_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_CALBYP_SHIFT 31 -#define DDR_PHY_DX3GCR0_CALBYP_MASK 0x80000000U - -/*Master Delay Line Enable*/ -#undef DDR_PHY_DX3GCR0_MDLEN_DEFVAL -#undef DDR_PHY_DX3GCR0_MDLEN_SHIFT -#undef DDR_PHY_DX3GCR0_MDLEN_MASK -#define DDR_PHY_DX3GCR0_MDLEN_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_MDLEN_SHIFT 30 -#define DDR_PHY_DX3GCR0_MDLEN_MASK 0x40000000U - -/*Configurable ODT(TE) Phase Shift*/ -#undef DDR_PHY_DX3GCR0_CODTSHFT_DEFVAL -#undef DDR_PHY_DX3GCR0_CODTSHFT_SHIFT -#undef DDR_PHY_DX3GCR0_CODTSHFT_MASK -#define DDR_PHY_DX3GCR0_CODTSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_CODTSHFT_SHIFT 28 -#define DDR_PHY_DX3GCR0_CODTSHFT_MASK 0x30000000U - -/*DQS Duty Cycle Correction*/ -#undef DDR_PHY_DX3GCR0_DQSDCC_DEFVAL -#undef DDR_PHY_DX3GCR0_DQSDCC_SHIFT -#undef DDR_PHY_DX3GCR0_DQSDCC_MASK -#define DDR_PHY_DX3GCR0_DQSDCC_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_DQSDCC_SHIFT 24 -#define DDR_PHY_DX3GCR0_DQSDCC_MASK 0x0F000000U - -/*Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY*/ -#undef DDR_PHY_DX3GCR0_RDDLY_DEFVAL -#undef DDR_PHY_DX3GCR0_RDDLY_SHIFT -#undef DDR_PHY_DX3GCR0_RDDLY_MASK -#define DDR_PHY_DX3GCR0_RDDLY_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_RDDLY_SHIFT 20 -#define DDR_PHY_DX3GCR0_RDDLY_MASK 0x00F00000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX3GCR0_RESERVED_19_14_DEFVAL -#undef DDR_PHY_DX3GCR0_RESERVED_19_14_SHIFT -#undef DDR_PHY_DX3GCR0_RESERVED_19_14_MASK -#define DDR_PHY_DX3GCR0_RESERVED_19_14_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_RESERVED_19_14_SHIFT 14 -#define DDR_PHY_DX3GCR0_RESERVED_19_14_MASK 0x000FC000U - -/*DQSNSE Power Down Receiver*/ -#undef DDR_PHY_DX3GCR0_DQSNSEPDR_DEFVAL -#undef DDR_PHY_DX3GCR0_DQSNSEPDR_SHIFT -#undef DDR_PHY_DX3GCR0_DQSNSEPDR_MASK -#define DDR_PHY_DX3GCR0_DQSNSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_DQSNSEPDR_SHIFT 13 -#define DDR_PHY_DX3GCR0_DQSNSEPDR_MASK 0x00002000U - -/*DQSSE Power Down Receiver*/ -#undef DDR_PHY_DX3GCR0_DQSSEPDR_DEFVAL -#undef DDR_PHY_DX3GCR0_DQSSEPDR_SHIFT -#undef DDR_PHY_DX3GCR0_DQSSEPDR_MASK -#define DDR_PHY_DX3GCR0_DQSSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_DQSSEPDR_SHIFT 12 -#define DDR_PHY_DX3GCR0_DQSSEPDR_MASK 0x00001000U - -/*RTT On Additive Latency*/ -#undef DDR_PHY_DX3GCR0_RTTOAL_DEFVAL -#undef DDR_PHY_DX3GCR0_RTTOAL_SHIFT -#undef DDR_PHY_DX3GCR0_RTTOAL_MASK -#define DDR_PHY_DX3GCR0_RTTOAL_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_RTTOAL_SHIFT 11 -#define DDR_PHY_DX3GCR0_RTTOAL_MASK 0x00000800U - -/*RTT Output Hold*/ -#undef DDR_PHY_DX3GCR0_RTTOH_DEFVAL -#undef DDR_PHY_DX3GCR0_RTTOH_SHIFT -#undef DDR_PHY_DX3GCR0_RTTOH_MASK -#define DDR_PHY_DX3GCR0_RTTOH_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_RTTOH_SHIFT 9 -#define DDR_PHY_DX3GCR0_RTTOH_MASK 0x00000600U - -/*Configurable PDR Phase Shift*/ -#undef DDR_PHY_DX3GCR0_CPDRSHFT_DEFVAL -#undef DDR_PHY_DX3GCR0_CPDRSHFT_SHIFT -#undef DDR_PHY_DX3GCR0_CPDRSHFT_MASK -#define DDR_PHY_DX3GCR0_CPDRSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_CPDRSHFT_SHIFT 7 -#define DDR_PHY_DX3GCR0_CPDRSHFT_MASK 0x00000180U - -/*DQSR Power Down*/ -#undef DDR_PHY_DX3GCR0_DQSRPD_DEFVAL -#undef DDR_PHY_DX3GCR0_DQSRPD_SHIFT -#undef DDR_PHY_DX3GCR0_DQSRPD_MASK -#define DDR_PHY_DX3GCR0_DQSRPD_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_DQSRPD_SHIFT 6 -#define DDR_PHY_DX3GCR0_DQSRPD_MASK 0x00000040U - -/*DQSG Power Down Receiver*/ -#undef DDR_PHY_DX3GCR0_DQSGPDR_DEFVAL -#undef DDR_PHY_DX3GCR0_DQSGPDR_SHIFT -#undef DDR_PHY_DX3GCR0_DQSGPDR_MASK -#define DDR_PHY_DX3GCR0_DQSGPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_DQSGPDR_SHIFT 5 -#define DDR_PHY_DX3GCR0_DQSGPDR_MASK 0x00000020U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX3GCR0_RESERVED_4_DEFVAL -#undef DDR_PHY_DX3GCR0_RESERVED_4_SHIFT -#undef DDR_PHY_DX3GCR0_RESERVED_4_MASK -#define DDR_PHY_DX3GCR0_RESERVED_4_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_RESERVED_4_SHIFT 4 -#define DDR_PHY_DX3GCR0_RESERVED_4_MASK 0x00000010U - -/*DQSG On-Die Termination*/ -#undef DDR_PHY_DX3GCR0_DQSGODT_DEFVAL -#undef DDR_PHY_DX3GCR0_DQSGODT_SHIFT -#undef DDR_PHY_DX3GCR0_DQSGODT_MASK -#define DDR_PHY_DX3GCR0_DQSGODT_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_DQSGODT_SHIFT 3 -#define DDR_PHY_DX3GCR0_DQSGODT_MASK 0x00000008U - -/*DQSG Output Enable*/ -#undef DDR_PHY_DX3GCR0_DQSGOE_DEFVAL -#undef DDR_PHY_DX3GCR0_DQSGOE_SHIFT -#undef DDR_PHY_DX3GCR0_DQSGOE_MASK -#define DDR_PHY_DX3GCR0_DQSGOE_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_DQSGOE_SHIFT 2 -#define DDR_PHY_DX3GCR0_DQSGOE_MASK 0x00000004U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX3GCR0_RESERVED_1_0_DEFVAL -#undef DDR_PHY_DX3GCR0_RESERVED_1_0_SHIFT -#undef DDR_PHY_DX3GCR0_RESERVED_1_0_MASK -#define DDR_PHY_DX3GCR0_RESERVED_1_0_DEFVAL 0x40200204 -#define DDR_PHY_DX3GCR0_RESERVED_1_0_SHIFT 0 -#define DDR_PHY_DX3GCR0_RESERVED_1_0_MASK 0x00000003U - -/*Enables the PDR mode for DQ[7:0]*/ -#undef DDR_PHY_DX3GCR1_DXPDRMODE_DEFVAL -#undef DDR_PHY_DX3GCR1_DXPDRMODE_SHIFT -#undef DDR_PHY_DX3GCR1_DXPDRMODE_MASK -#define DDR_PHY_DX3GCR1_DXPDRMODE_DEFVAL 0x00007FFF -#define DDR_PHY_DX3GCR1_DXPDRMODE_SHIFT 16 -#define DDR_PHY_DX3GCR1_DXPDRMODE_MASK 0xFFFF0000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_DX3GCR1_RESERVED_15_DEFVAL -#undef DDR_PHY_DX3GCR1_RESERVED_15_SHIFT -#undef DDR_PHY_DX3GCR1_RESERVED_15_MASK -#define DDR_PHY_DX3GCR1_RESERVED_15_DEFVAL 0x00007FFF -#define DDR_PHY_DX3GCR1_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX3GCR1_RESERVED_15_MASK 0x00008000U - -/*Select the delayed or non-delayed read data strobe #*/ -#undef DDR_PHY_DX3GCR1_QSNSEL_DEFVAL -#undef DDR_PHY_DX3GCR1_QSNSEL_SHIFT -#undef DDR_PHY_DX3GCR1_QSNSEL_MASK -#define DDR_PHY_DX3GCR1_QSNSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX3GCR1_QSNSEL_SHIFT 14 -#define DDR_PHY_DX3GCR1_QSNSEL_MASK 0x00004000U - -/*Select the delayed or non-delayed read data strobe*/ -#undef DDR_PHY_DX3GCR1_QSSEL_DEFVAL -#undef DDR_PHY_DX3GCR1_QSSEL_SHIFT -#undef DDR_PHY_DX3GCR1_QSSEL_MASK -#define DDR_PHY_DX3GCR1_QSSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX3GCR1_QSSEL_SHIFT 13 -#define DDR_PHY_DX3GCR1_QSSEL_MASK 0x00002000U - -/*Enables Read Data Strobe in a byte lane*/ -#undef DDR_PHY_DX3GCR1_OEEN_DEFVAL -#undef DDR_PHY_DX3GCR1_OEEN_SHIFT -#undef DDR_PHY_DX3GCR1_OEEN_MASK -#define DDR_PHY_DX3GCR1_OEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX3GCR1_OEEN_SHIFT 12 -#define DDR_PHY_DX3GCR1_OEEN_MASK 0x00001000U - -/*Enables PDR in a byte lane*/ -#undef DDR_PHY_DX3GCR1_PDREN_DEFVAL -#undef DDR_PHY_DX3GCR1_PDREN_SHIFT -#undef DDR_PHY_DX3GCR1_PDREN_MASK -#define DDR_PHY_DX3GCR1_PDREN_DEFVAL 0x00007FFF -#define DDR_PHY_DX3GCR1_PDREN_SHIFT 11 -#define DDR_PHY_DX3GCR1_PDREN_MASK 0x00000800U - -/*Enables ODT/TE in a byte lane*/ -#undef DDR_PHY_DX3GCR1_TEEN_DEFVAL -#undef DDR_PHY_DX3GCR1_TEEN_SHIFT -#undef DDR_PHY_DX3GCR1_TEEN_MASK -#define DDR_PHY_DX3GCR1_TEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX3GCR1_TEEN_SHIFT 10 -#define DDR_PHY_DX3GCR1_TEEN_MASK 0x00000400U - -/*Enables Write Data strobe in a byte lane*/ -#undef DDR_PHY_DX3GCR1_DSEN_DEFVAL -#undef DDR_PHY_DX3GCR1_DSEN_SHIFT -#undef DDR_PHY_DX3GCR1_DSEN_MASK -#define DDR_PHY_DX3GCR1_DSEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX3GCR1_DSEN_SHIFT 9 -#define DDR_PHY_DX3GCR1_DSEN_MASK 0x00000200U - -/*Enables DM pin in a byte lane*/ -#undef DDR_PHY_DX3GCR1_DMEN_DEFVAL -#undef DDR_PHY_DX3GCR1_DMEN_SHIFT -#undef DDR_PHY_DX3GCR1_DMEN_MASK -#define DDR_PHY_DX3GCR1_DMEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX3GCR1_DMEN_SHIFT 8 -#define DDR_PHY_DX3GCR1_DMEN_MASK 0x00000100U - -/*Enables DQ corresponding to each bit in a byte*/ -#undef DDR_PHY_DX3GCR1_DQEN_DEFVAL -#undef DDR_PHY_DX3GCR1_DQEN_SHIFT -#undef DDR_PHY_DX3GCR1_DQEN_MASK -#define DDR_PHY_DX3GCR1_DQEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX3GCR1_DQEN_SHIFT 0 -#define DDR_PHY_DX3GCR1_DQEN_MASK 0x000000FFU - -/*Byte lane VREF IOM (Used only by D4MU IOs)*/ -#undef DDR_PHY_DX3GCR4_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DX3GCR4_RESERVED_31_29_SHIFT -#undef DDR_PHY_DX3GCR4_RESERVED_31_29_MASK -#define DDR_PHY_DX3GCR4_RESERVED_31_29_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DX3GCR4_RESERVED_31_29_MASK 0xE0000000U - -/*Byte Lane VREF Pad Enable*/ -#undef DDR_PHY_DX3GCR4_DXREFPEN_DEFVAL -#undef DDR_PHY_DX3GCR4_DXREFPEN_SHIFT -#undef DDR_PHY_DX3GCR4_DXREFPEN_MASK -#define DDR_PHY_DX3GCR4_DXREFPEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_DXREFPEN_SHIFT 28 -#define DDR_PHY_DX3GCR4_DXREFPEN_MASK 0x10000000U - -/*Byte Lane Internal VREF Enable*/ -#undef DDR_PHY_DX3GCR4_DXREFEEN_DEFVAL -#undef DDR_PHY_DX3GCR4_DXREFEEN_SHIFT -#undef DDR_PHY_DX3GCR4_DXREFEEN_MASK -#define DDR_PHY_DX3GCR4_DXREFEEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_DXREFEEN_SHIFT 26 -#define DDR_PHY_DX3GCR4_DXREFEEN_MASK 0x0C000000U - -/*Byte Lane Single-End VREF Enable*/ -#undef DDR_PHY_DX3GCR4_DXREFSEN_DEFVAL -#undef DDR_PHY_DX3GCR4_DXREFSEN_SHIFT -#undef DDR_PHY_DX3GCR4_DXREFSEN_MASK -#define DDR_PHY_DX3GCR4_DXREFSEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_DXREFSEN_SHIFT 25 -#define DDR_PHY_DX3GCR4_DXREFSEN_MASK 0x02000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX3GCR4_RESERVED_24_DEFVAL -#undef DDR_PHY_DX3GCR4_RESERVED_24_SHIFT -#undef DDR_PHY_DX3GCR4_RESERVED_24_MASK -#define DDR_PHY_DX3GCR4_RESERVED_24_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_RESERVED_24_SHIFT 24 -#define DDR_PHY_DX3GCR4_RESERVED_24_MASK 0x01000000U - -/*External VREF generator REFSEL range select*/ -#undef DDR_PHY_DX3GCR4_DXREFESELRANGE_DEFVAL -#undef DDR_PHY_DX3GCR4_DXREFESELRANGE_SHIFT -#undef DDR_PHY_DX3GCR4_DXREFESELRANGE_MASK -#define DDR_PHY_DX3GCR4_DXREFESELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_DXREFESELRANGE_SHIFT 23 -#define DDR_PHY_DX3GCR4_DXREFESELRANGE_MASK 0x00800000U - -/*Byte Lane External VREF Select*/ -#undef DDR_PHY_DX3GCR4_DXREFESEL_DEFVAL -#undef DDR_PHY_DX3GCR4_DXREFESEL_SHIFT -#undef DDR_PHY_DX3GCR4_DXREFESEL_MASK -#define DDR_PHY_DX3GCR4_DXREFESEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_DXREFESEL_SHIFT 16 -#define DDR_PHY_DX3GCR4_DXREFESEL_MASK 0x007F0000U - -/*Single ended VREF generator REFSEL range select*/ -#undef DDR_PHY_DX3GCR4_DXREFSSELRANGE_DEFVAL -#undef DDR_PHY_DX3GCR4_DXREFSSELRANGE_SHIFT -#undef DDR_PHY_DX3GCR4_DXREFSSELRANGE_MASK -#define DDR_PHY_DX3GCR4_DXREFSSELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_DXREFSSELRANGE_SHIFT 15 -#define DDR_PHY_DX3GCR4_DXREFSSELRANGE_MASK 0x00008000U - -/*Byte Lane Single-End VREF Select*/ -#undef DDR_PHY_DX3GCR4_DXREFSSEL_DEFVAL -#undef DDR_PHY_DX3GCR4_DXREFSSEL_SHIFT -#undef DDR_PHY_DX3GCR4_DXREFSSEL_MASK -#define DDR_PHY_DX3GCR4_DXREFSSEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_DXREFSSEL_SHIFT 8 -#define DDR_PHY_DX3GCR4_DXREFSSEL_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX3GCR4_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX3GCR4_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX3GCR4_RESERVED_7_6_MASK -#define DDR_PHY_DX3GCR4_RESERVED_7_6_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX3GCR4_RESERVED_7_6_MASK 0x000000C0U - -/*VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX3GCR4_DXREFIEN_DEFVAL -#undef DDR_PHY_DX3GCR4_DXREFIEN_SHIFT -#undef DDR_PHY_DX3GCR4_DXREFIEN_MASK -#define DDR_PHY_DX3GCR4_DXREFIEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_DXREFIEN_SHIFT 2 -#define DDR_PHY_DX3GCR4_DXREFIEN_MASK 0x0000003CU - -/*VRMON control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX3GCR4_DXREFIMON_DEFVAL -#undef DDR_PHY_DX3GCR4_DXREFIMON_SHIFT -#undef DDR_PHY_DX3GCR4_DXREFIMON_MASK -#define DDR_PHY_DX3GCR4_DXREFIMON_DEFVAL 0x0E00003C -#define DDR_PHY_DX3GCR4_DXREFIMON_SHIFT 0 -#define DDR_PHY_DX3GCR4_DXREFIMON_MASK 0x00000003U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX3GCR5_RESERVED_31_DEFVAL -#undef DDR_PHY_DX3GCR5_RESERVED_31_SHIFT -#undef DDR_PHY_DX3GCR5_RESERVED_31_MASK -#define DDR_PHY_DX3GCR5_RESERVED_31_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR5_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX3GCR5_RESERVED_31_MASK 0x80000000U - -/*Byte Lane internal VREF Select for Rank 3*/ -#undef DDR_PHY_DX3GCR5_DXREFISELR3_DEFVAL -#undef DDR_PHY_DX3GCR5_DXREFISELR3_SHIFT -#undef DDR_PHY_DX3GCR5_DXREFISELR3_MASK -#define DDR_PHY_DX3GCR5_DXREFISELR3_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR5_DXREFISELR3_SHIFT 24 -#define DDR_PHY_DX3GCR5_DXREFISELR3_MASK 0x7F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX3GCR5_RESERVED_23_DEFVAL -#undef DDR_PHY_DX3GCR5_RESERVED_23_SHIFT -#undef DDR_PHY_DX3GCR5_RESERVED_23_MASK -#define DDR_PHY_DX3GCR5_RESERVED_23_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR5_RESERVED_23_SHIFT 23 -#define DDR_PHY_DX3GCR5_RESERVED_23_MASK 0x00800000U - -/*Byte Lane internal VREF Select for Rank 2*/ -#undef DDR_PHY_DX3GCR5_DXREFISELR2_DEFVAL -#undef DDR_PHY_DX3GCR5_DXREFISELR2_SHIFT -#undef DDR_PHY_DX3GCR5_DXREFISELR2_MASK -#define DDR_PHY_DX3GCR5_DXREFISELR2_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR5_DXREFISELR2_SHIFT 16 -#define DDR_PHY_DX3GCR5_DXREFISELR2_MASK 0x007F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX3GCR5_RESERVED_15_DEFVAL -#undef DDR_PHY_DX3GCR5_RESERVED_15_SHIFT -#undef DDR_PHY_DX3GCR5_RESERVED_15_MASK -#define DDR_PHY_DX3GCR5_RESERVED_15_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR5_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX3GCR5_RESERVED_15_MASK 0x00008000U - -/*Byte Lane internal VREF Select for Rank 1*/ -#undef DDR_PHY_DX3GCR5_DXREFISELR1_DEFVAL -#undef DDR_PHY_DX3GCR5_DXREFISELR1_SHIFT -#undef DDR_PHY_DX3GCR5_DXREFISELR1_MASK -#define DDR_PHY_DX3GCR5_DXREFISELR1_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR5_DXREFISELR1_SHIFT 8 -#define DDR_PHY_DX3GCR5_DXREFISELR1_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX3GCR5_RESERVED_7_DEFVAL -#undef DDR_PHY_DX3GCR5_RESERVED_7_SHIFT -#undef DDR_PHY_DX3GCR5_RESERVED_7_MASK -#define DDR_PHY_DX3GCR5_RESERVED_7_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR5_RESERVED_7_SHIFT 7 -#define DDR_PHY_DX3GCR5_RESERVED_7_MASK 0x00000080U - -/*Byte Lane internal VREF Select for Rank 0*/ -#undef DDR_PHY_DX3GCR5_DXREFISELR0_DEFVAL -#undef DDR_PHY_DX3GCR5_DXREFISELR0_SHIFT -#undef DDR_PHY_DX3GCR5_DXREFISELR0_MASK -#define DDR_PHY_DX3GCR5_DXREFISELR0_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR5_DXREFISELR0_SHIFT 0 -#define DDR_PHY_DX3GCR5_DXREFISELR0_MASK 0x0000007FU - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX3GCR6_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX3GCR6_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX3GCR6_RESERVED_31_30_MASK -#define DDR_PHY_DX3GCR6_RESERVED_31_30_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR6_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX3GCR6_RESERVED_31_30_MASK 0xC0000000U - -/*DRAM DQ VREF Select for Rank3*/ -#undef DDR_PHY_DX3GCR6_DXDQVREFR3_DEFVAL -#undef DDR_PHY_DX3GCR6_DXDQVREFR3_SHIFT -#undef DDR_PHY_DX3GCR6_DXDQVREFR3_MASK -#define DDR_PHY_DX3GCR6_DXDQVREFR3_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR6_DXDQVREFR3_SHIFT 24 -#define DDR_PHY_DX3GCR6_DXDQVREFR3_MASK 0x3F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX3GCR6_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX3GCR6_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX3GCR6_RESERVED_23_22_MASK -#define DDR_PHY_DX3GCR6_RESERVED_23_22_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR6_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX3GCR6_RESERVED_23_22_MASK 0x00C00000U - -/*DRAM DQ VREF Select for Rank2*/ -#undef DDR_PHY_DX3GCR6_DXDQVREFR2_DEFVAL -#undef DDR_PHY_DX3GCR6_DXDQVREFR2_SHIFT -#undef DDR_PHY_DX3GCR6_DXDQVREFR2_MASK -#define DDR_PHY_DX3GCR6_DXDQVREFR2_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR6_DXDQVREFR2_SHIFT 16 -#define DDR_PHY_DX3GCR6_DXDQVREFR2_MASK 0x003F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX3GCR6_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DX3GCR6_RESERVED_15_14_SHIFT -#undef DDR_PHY_DX3GCR6_RESERVED_15_14_MASK -#define DDR_PHY_DX3GCR6_RESERVED_15_14_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR6_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DX3GCR6_RESERVED_15_14_MASK 0x0000C000U - -/*DRAM DQ VREF Select for Rank1*/ -#undef DDR_PHY_DX3GCR6_DXDQVREFR1_DEFVAL -#undef DDR_PHY_DX3GCR6_DXDQVREFR1_SHIFT -#undef DDR_PHY_DX3GCR6_DXDQVREFR1_MASK -#define DDR_PHY_DX3GCR6_DXDQVREFR1_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR6_DXDQVREFR1_SHIFT 8 -#define DDR_PHY_DX3GCR6_DXDQVREFR1_MASK 0x00003F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX3GCR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX3GCR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX3GCR6_RESERVED_7_6_MASK -#define DDR_PHY_DX3GCR6_RESERVED_7_6_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX3GCR6_RESERVED_7_6_MASK 0x000000C0U - -/*DRAM DQ VREF Select for Rank0*/ -#undef DDR_PHY_DX3GCR6_DXDQVREFR0_DEFVAL -#undef DDR_PHY_DX3GCR6_DXDQVREFR0_SHIFT -#undef DDR_PHY_DX3GCR6_DXDQVREFR0_MASK -#define DDR_PHY_DX3GCR6_DXDQVREFR0_DEFVAL 0x09090909 -#define DDR_PHY_DX3GCR6_DXDQVREFR0_SHIFT 0 -#define DDR_PHY_DX3GCR6_DXDQVREFR0_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX3LCDLR2_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX3LCDLR2_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX3LCDLR2_RESERVED_31_25_MASK -#define DDR_PHY_DX3LCDLR2_RESERVED_31_25_DEFVAL 0x00000000 -#define DDR_PHY_DX3LCDLR2_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX3LCDLR2_RESERVED_31_25_MASK 0xFE000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX3LCDLR2_RESERVED_24_16_DEFVAL -#undef DDR_PHY_DX3LCDLR2_RESERVED_24_16_SHIFT -#undef DDR_PHY_DX3LCDLR2_RESERVED_24_16_MASK -#define DDR_PHY_DX3LCDLR2_RESERVED_24_16_DEFVAL 0x00000000 -#define DDR_PHY_DX3LCDLR2_RESERVED_24_16_SHIFT 16 -#define DDR_PHY_DX3LCDLR2_RESERVED_24_16_MASK 0x01FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX3LCDLR2_RESERVED_15_9_DEFVAL -#undef DDR_PHY_DX3LCDLR2_RESERVED_15_9_SHIFT -#undef DDR_PHY_DX3LCDLR2_RESERVED_15_9_MASK -#define DDR_PHY_DX3LCDLR2_RESERVED_15_9_DEFVAL 0x00000000 -#define DDR_PHY_DX3LCDLR2_RESERVED_15_9_SHIFT 9 -#define DDR_PHY_DX3LCDLR2_RESERVED_15_9_MASK 0x0000FE00U - -/*Read DQS Gating Delay*/ -#undef DDR_PHY_DX3LCDLR2_DQSGD_DEFVAL -#undef DDR_PHY_DX3LCDLR2_DQSGD_SHIFT -#undef DDR_PHY_DX3LCDLR2_DQSGD_MASK -#define DDR_PHY_DX3LCDLR2_DQSGD_DEFVAL 0x00000000 -#define DDR_PHY_DX3LCDLR2_DQSGD_SHIFT 0 -#define DDR_PHY_DX3LCDLR2_DQSGD_MASK 0x000001FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX3GTR0_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX3GTR0_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX3GTR0_RESERVED_31_24_MASK -#define DDR_PHY_DX3GTR0_RESERVED_31_24_DEFVAL 0x00020000 -#define DDR_PHY_DX3GTR0_RESERVED_31_24_SHIFT 27 -#define DDR_PHY_DX3GTR0_RESERVED_31_24_MASK 0xF8000000U - -/*DQ Write Path Latency Pipeline*/ -#undef DDR_PHY_DX3GTR0_WDQSL_DEFVAL -#undef DDR_PHY_DX3GTR0_WDQSL_SHIFT -#undef DDR_PHY_DX3GTR0_WDQSL_MASK -#define DDR_PHY_DX3GTR0_WDQSL_DEFVAL 0x00020000 -#define DDR_PHY_DX3GTR0_WDQSL_SHIFT 24 -#define DDR_PHY_DX3GTR0_WDQSL_MASK 0x07000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX3GTR0_RESERVED_23_20_DEFVAL -#undef DDR_PHY_DX3GTR0_RESERVED_23_20_SHIFT -#undef DDR_PHY_DX3GTR0_RESERVED_23_20_MASK -#define DDR_PHY_DX3GTR0_RESERVED_23_20_DEFVAL 0x00020000 -#define DDR_PHY_DX3GTR0_RESERVED_23_20_SHIFT 20 -#define DDR_PHY_DX3GTR0_RESERVED_23_20_MASK 0x00F00000U - -/*Write Leveling System Latency*/ -#undef DDR_PHY_DX3GTR0_WLSL_DEFVAL -#undef DDR_PHY_DX3GTR0_WLSL_SHIFT -#undef DDR_PHY_DX3GTR0_WLSL_MASK -#define DDR_PHY_DX3GTR0_WLSL_DEFVAL 0x00020000 -#define DDR_PHY_DX3GTR0_WLSL_SHIFT 16 -#define DDR_PHY_DX3GTR0_WLSL_MASK 0x000F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX3GTR0_RESERVED_15_13_DEFVAL -#undef DDR_PHY_DX3GTR0_RESERVED_15_13_SHIFT -#undef DDR_PHY_DX3GTR0_RESERVED_15_13_MASK -#define DDR_PHY_DX3GTR0_RESERVED_15_13_DEFVAL 0x00020000 -#define DDR_PHY_DX3GTR0_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_DX3GTR0_RESERVED_15_13_MASK 0x0000E000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX3GTR0_RESERVED_12_8_DEFVAL -#undef DDR_PHY_DX3GTR0_RESERVED_12_8_SHIFT -#undef DDR_PHY_DX3GTR0_RESERVED_12_8_MASK -#define DDR_PHY_DX3GTR0_RESERVED_12_8_DEFVAL 0x00020000 -#define DDR_PHY_DX3GTR0_RESERVED_12_8_SHIFT 8 -#define DDR_PHY_DX3GTR0_RESERVED_12_8_MASK 0x00001F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX3GTR0_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DX3GTR0_RESERVED_7_5_SHIFT -#undef DDR_PHY_DX3GTR0_RESERVED_7_5_MASK -#define DDR_PHY_DX3GTR0_RESERVED_7_5_DEFVAL 0x00020000 -#define DDR_PHY_DX3GTR0_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DX3GTR0_RESERVED_7_5_MASK 0x000000E0U - -/*DQS Gating System Latency*/ -#undef DDR_PHY_DX3GTR0_DGSL_DEFVAL -#undef DDR_PHY_DX3GTR0_DGSL_SHIFT -#undef DDR_PHY_DX3GTR0_DGSL_MASK -#define DDR_PHY_DX3GTR0_DGSL_DEFVAL 0x00020000 -#define DDR_PHY_DX3GTR0_DGSL_SHIFT 0 -#define DDR_PHY_DX3GTR0_DGSL_MASK 0x0000001FU - -/*Calibration Bypass*/ -#undef DDR_PHY_DX4GCR0_CALBYP_DEFVAL -#undef DDR_PHY_DX4GCR0_CALBYP_SHIFT -#undef DDR_PHY_DX4GCR0_CALBYP_MASK -#define DDR_PHY_DX4GCR0_CALBYP_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_CALBYP_SHIFT 31 -#define DDR_PHY_DX4GCR0_CALBYP_MASK 0x80000000U - -/*Master Delay Line Enable*/ -#undef DDR_PHY_DX4GCR0_MDLEN_DEFVAL -#undef DDR_PHY_DX4GCR0_MDLEN_SHIFT -#undef DDR_PHY_DX4GCR0_MDLEN_MASK -#define DDR_PHY_DX4GCR0_MDLEN_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_MDLEN_SHIFT 30 -#define DDR_PHY_DX4GCR0_MDLEN_MASK 0x40000000U - -/*Configurable ODT(TE) Phase Shift*/ -#undef DDR_PHY_DX4GCR0_CODTSHFT_DEFVAL -#undef DDR_PHY_DX4GCR0_CODTSHFT_SHIFT -#undef DDR_PHY_DX4GCR0_CODTSHFT_MASK -#define DDR_PHY_DX4GCR0_CODTSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_CODTSHFT_SHIFT 28 -#define DDR_PHY_DX4GCR0_CODTSHFT_MASK 0x30000000U - -/*DQS Duty Cycle Correction*/ -#undef DDR_PHY_DX4GCR0_DQSDCC_DEFVAL -#undef DDR_PHY_DX4GCR0_DQSDCC_SHIFT -#undef DDR_PHY_DX4GCR0_DQSDCC_MASK -#define DDR_PHY_DX4GCR0_DQSDCC_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_DQSDCC_SHIFT 24 -#define DDR_PHY_DX4GCR0_DQSDCC_MASK 0x0F000000U - -/*Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY*/ -#undef DDR_PHY_DX4GCR0_RDDLY_DEFVAL -#undef DDR_PHY_DX4GCR0_RDDLY_SHIFT -#undef DDR_PHY_DX4GCR0_RDDLY_MASK -#define DDR_PHY_DX4GCR0_RDDLY_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_RDDLY_SHIFT 20 -#define DDR_PHY_DX4GCR0_RDDLY_MASK 0x00F00000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX4GCR0_RESERVED_19_14_DEFVAL -#undef DDR_PHY_DX4GCR0_RESERVED_19_14_SHIFT -#undef DDR_PHY_DX4GCR0_RESERVED_19_14_MASK -#define DDR_PHY_DX4GCR0_RESERVED_19_14_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_RESERVED_19_14_SHIFT 14 -#define DDR_PHY_DX4GCR0_RESERVED_19_14_MASK 0x000FC000U - -/*DQSNSE Power Down Receiver*/ -#undef DDR_PHY_DX4GCR0_DQSNSEPDR_DEFVAL -#undef DDR_PHY_DX4GCR0_DQSNSEPDR_SHIFT -#undef DDR_PHY_DX4GCR0_DQSNSEPDR_MASK -#define DDR_PHY_DX4GCR0_DQSNSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_DQSNSEPDR_SHIFT 13 -#define DDR_PHY_DX4GCR0_DQSNSEPDR_MASK 0x00002000U - -/*DQSSE Power Down Receiver*/ -#undef DDR_PHY_DX4GCR0_DQSSEPDR_DEFVAL -#undef DDR_PHY_DX4GCR0_DQSSEPDR_SHIFT -#undef DDR_PHY_DX4GCR0_DQSSEPDR_MASK -#define DDR_PHY_DX4GCR0_DQSSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_DQSSEPDR_SHIFT 12 -#define DDR_PHY_DX4GCR0_DQSSEPDR_MASK 0x00001000U - -/*RTT On Additive Latency*/ -#undef DDR_PHY_DX4GCR0_RTTOAL_DEFVAL -#undef DDR_PHY_DX4GCR0_RTTOAL_SHIFT -#undef DDR_PHY_DX4GCR0_RTTOAL_MASK -#define DDR_PHY_DX4GCR0_RTTOAL_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_RTTOAL_SHIFT 11 -#define DDR_PHY_DX4GCR0_RTTOAL_MASK 0x00000800U - -/*RTT Output Hold*/ -#undef DDR_PHY_DX4GCR0_RTTOH_DEFVAL -#undef DDR_PHY_DX4GCR0_RTTOH_SHIFT -#undef DDR_PHY_DX4GCR0_RTTOH_MASK -#define DDR_PHY_DX4GCR0_RTTOH_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_RTTOH_SHIFT 9 -#define DDR_PHY_DX4GCR0_RTTOH_MASK 0x00000600U - -/*Configurable PDR Phase Shift*/ -#undef DDR_PHY_DX4GCR0_CPDRSHFT_DEFVAL -#undef DDR_PHY_DX4GCR0_CPDRSHFT_SHIFT -#undef DDR_PHY_DX4GCR0_CPDRSHFT_MASK -#define DDR_PHY_DX4GCR0_CPDRSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_CPDRSHFT_SHIFT 7 -#define DDR_PHY_DX4GCR0_CPDRSHFT_MASK 0x00000180U - -/*DQSR Power Down*/ -#undef DDR_PHY_DX4GCR0_DQSRPD_DEFVAL -#undef DDR_PHY_DX4GCR0_DQSRPD_SHIFT -#undef DDR_PHY_DX4GCR0_DQSRPD_MASK -#define DDR_PHY_DX4GCR0_DQSRPD_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_DQSRPD_SHIFT 6 -#define DDR_PHY_DX4GCR0_DQSRPD_MASK 0x00000040U - -/*DQSG Power Down Receiver*/ -#undef DDR_PHY_DX4GCR0_DQSGPDR_DEFVAL -#undef DDR_PHY_DX4GCR0_DQSGPDR_SHIFT -#undef DDR_PHY_DX4GCR0_DQSGPDR_MASK -#define DDR_PHY_DX4GCR0_DQSGPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_DQSGPDR_SHIFT 5 -#define DDR_PHY_DX4GCR0_DQSGPDR_MASK 0x00000020U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX4GCR0_RESERVED_4_DEFVAL -#undef DDR_PHY_DX4GCR0_RESERVED_4_SHIFT -#undef DDR_PHY_DX4GCR0_RESERVED_4_MASK -#define DDR_PHY_DX4GCR0_RESERVED_4_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_RESERVED_4_SHIFT 4 -#define DDR_PHY_DX4GCR0_RESERVED_4_MASK 0x00000010U - -/*DQSG On-Die Termination*/ -#undef DDR_PHY_DX4GCR0_DQSGODT_DEFVAL -#undef DDR_PHY_DX4GCR0_DQSGODT_SHIFT -#undef DDR_PHY_DX4GCR0_DQSGODT_MASK -#define DDR_PHY_DX4GCR0_DQSGODT_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_DQSGODT_SHIFT 3 -#define DDR_PHY_DX4GCR0_DQSGODT_MASK 0x00000008U - -/*DQSG Output Enable*/ -#undef DDR_PHY_DX4GCR0_DQSGOE_DEFVAL -#undef DDR_PHY_DX4GCR0_DQSGOE_SHIFT -#undef DDR_PHY_DX4GCR0_DQSGOE_MASK -#define DDR_PHY_DX4GCR0_DQSGOE_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_DQSGOE_SHIFT 2 -#define DDR_PHY_DX4GCR0_DQSGOE_MASK 0x00000004U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX4GCR0_RESERVED_1_0_DEFVAL -#undef DDR_PHY_DX4GCR0_RESERVED_1_0_SHIFT -#undef DDR_PHY_DX4GCR0_RESERVED_1_0_MASK -#define DDR_PHY_DX4GCR0_RESERVED_1_0_DEFVAL 0x40200204 -#define DDR_PHY_DX4GCR0_RESERVED_1_0_SHIFT 0 -#define DDR_PHY_DX4GCR0_RESERVED_1_0_MASK 0x00000003U - -/*Enables the PDR mode for DQ[7:0]*/ -#undef DDR_PHY_DX4GCR1_DXPDRMODE_DEFVAL -#undef DDR_PHY_DX4GCR1_DXPDRMODE_SHIFT -#undef DDR_PHY_DX4GCR1_DXPDRMODE_MASK -#define DDR_PHY_DX4GCR1_DXPDRMODE_DEFVAL 0x00007FFF -#define DDR_PHY_DX4GCR1_DXPDRMODE_SHIFT 16 -#define DDR_PHY_DX4GCR1_DXPDRMODE_MASK 0xFFFF0000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_DX4GCR1_RESERVED_15_DEFVAL -#undef DDR_PHY_DX4GCR1_RESERVED_15_SHIFT -#undef DDR_PHY_DX4GCR1_RESERVED_15_MASK -#define DDR_PHY_DX4GCR1_RESERVED_15_DEFVAL 0x00007FFF -#define DDR_PHY_DX4GCR1_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX4GCR1_RESERVED_15_MASK 0x00008000U - -/*Select the delayed or non-delayed read data strobe #*/ -#undef DDR_PHY_DX4GCR1_QSNSEL_DEFVAL -#undef DDR_PHY_DX4GCR1_QSNSEL_SHIFT -#undef DDR_PHY_DX4GCR1_QSNSEL_MASK -#define DDR_PHY_DX4GCR1_QSNSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX4GCR1_QSNSEL_SHIFT 14 -#define DDR_PHY_DX4GCR1_QSNSEL_MASK 0x00004000U - -/*Select the delayed or non-delayed read data strobe*/ -#undef DDR_PHY_DX4GCR1_QSSEL_DEFVAL -#undef DDR_PHY_DX4GCR1_QSSEL_SHIFT -#undef DDR_PHY_DX4GCR1_QSSEL_MASK -#define DDR_PHY_DX4GCR1_QSSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX4GCR1_QSSEL_SHIFT 13 -#define DDR_PHY_DX4GCR1_QSSEL_MASK 0x00002000U - -/*Enables Read Data Strobe in a byte lane*/ -#undef DDR_PHY_DX4GCR1_OEEN_DEFVAL -#undef DDR_PHY_DX4GCR1_OEEN_SHIFT -#undef DDR_PHY_DX4GCR1_OEEN_MASK -#define DDR_PHY_DX4GCR1_OEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX4GCR1_OEEN_SHIFT 12 -#define DDR_PHY_DX4GCR1_OEEN_MASK 0x00001000U - -/*Enables PDR in a byte lane*/ -#undef DDR_PHY_DX4GCR1_PDREN_DEFVAL -#undef DDR_PHY_DX4GCR1_PDREN_SHIFT -#undef DDR_PHY_DX4GCR1_PDREN_MASK -#define DDR_PHY_DX4GCR1_PDREN_DEFVAL 0x00007FFF -#define DDR_PHY_DX4GCR1_PDREN_SHIFT 11 -#define DDR_PHY_DX4GCR1_PDREN_MASK 0x00000800U - -/*Enables ODT/TE in a byte lane*/ -#undef DDR_PHY_DX4GCR1_TEEN_DEFVAL -#undef DDR_PHY_DX4GCR1_TEEN_SHIFT -#undef DDR_PHY_DX4GCR1_TEEN_MASK -#define DDR_PHY_DX4GCR1_TEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX4GCR1_TEEN_SHIFT 10 -#define DDR_PHY_DX4GCR1_TEEN_MASK 0x00000400U - -/*Enables Write Data strobe in a byte lane*/ -#undef DDR_PHY_DX4GCR1_DSEN_DEFVAL -#undef DDR_PHY_DX4GCR1_DSEN_SHIFT -#undef DDR_PHY_DX4GCR1_DSEN_MASK -#define DDR_PHY_DX4GCR1_DSEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX4GCR1_DSEN_SHIFT 9 -#define DDR_PHY_DX4GCR1_DSEN_MASK 0x00000200U - -/*Enables DM pin in a byte lane*/ -#undef DDR_PHY_DX4GCR1_DMEN_DEFVAL -#undef DDR_PHY_DX4GCR1_DMEN_SHIFT -#undef DDR_PHY_DX4GCR1_DMEN_MASK -#define DDR_PHY_DX4GCR1_DMEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX4GCR1_DMEN_SHIFT 8 -#define DDR_PHY_DX4GCR1_DMEN_MASK 0x00000100U - -/*Enables DQ corresponding to each bit in a byte*/ -#undef DDR_PHY_DX4GCR1_DQEN_DEFVAL -#undef DDR_PHY_DX4GCR1_DQEN_SHIFT -#undef DDR_PHY_DX4GCR1_DQEN_MASK -#define DDR_PHY_DX4GCR1_DQEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX4GCR1_DQEN_SHIFT 0 -#define DDR_PHY_DX4GCR1_DQEN_MASK 0x000000FFU - -/*Byte lane VREF IOM (Used only by D4MU IOs)*/ -#undef DDR_PHY_DX4GCR4_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DX4GCR4_RESERVED_31_29_SHIFT -#undef DDR_PHY_DX4GCR4_RESERVED_31_29_MASK -#define DDR_PHY_DX4GCR4_RESERVED_31_29_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DX4GCR4_RESERVED_31_29_MASK 0xE0000000U - -/*Byte Lane VREF Pad Enable*/ -#undef DDR_PHY_DX4GCR4_DXREFPEN_DEFVAL -#undef DDR_PHY_DX4GCR4_DXREFPEN_SHIFT -#undef DDR_PHY_DX4GCR4_DXREFPEN_MASK -#define DDR_PHY_DX4GCR4_DXREFPEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_DXREFPEN_SHIFT 28 -#define DDR_PHY_DX4GCR4_DXREFPEN_MASK 0x10000000U - -/*Byte Lane Internal VREF Enable*/ -#undef DDR_PHY_DX4GCR4_DXREFEEN_DEFVAL -#undef DDR_PHY_DX4GCR4_DXREFEEN_SHIFT -#undef DDR_PHY_DX4GCR4_DXREFEEN_MASK -#define DDR_PHY_DX4GCR4_DXREFEEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_DXREFEEN_SHIFT 26 -#define DDR_PHY_DX4GCR4_DXREFEEN_MASK 0x0C000000U - -/*Byte Lane Single-End VREF Enable*/ -#undef DDR_PHY_DX4GCR4_DXREFSEN_DEFVAL -#undef DDR_PHY_DX4GCR4_DXREFSEN_SHIFT -#undef DDR_PHY_DX4GCR4_DXREFSEN_MASK -#define DDR_PHY_DX4GCR4_DXREFSEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_DXREFSEN_SHIFT 25 -#define DDR_PHY_DX4GCR4_DXREFSEN_MASK 0x02000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX4GCR4_RESERVED_24_DEFVAL -#undef DDR_PHY_DX4GCR4_RESERVED_24_SHIFT -#undef DDR_PHY_DX4GCR4_RESERVED_24_MASK -#define DDR_PHY_DX4GCR4_RESERVED_24_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_RESERVED_24_SHIFT 24 -#define DDR_PHY_DX4GCR4_RESERVED_24_MASK 0x01000000U - -/*External VREF generator REFSEL range select*/ -#undef DDR_PHY_DX4GCR4_DXREFESELRANGE_DEFVAL -#undef DDR_PHY_DX4GCR4_DXREFESELRANGE_SHIFT -#undef DDR_PHY_DX4GCR4_DXREFESELRANGE_MASK -#define DDR_PHY_DX4GCR4_DXREFESELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_DXREFESELRANGE_SHIFT 23 -#define DDR_PHY_DX4GCR4_DXREFESELRANGE_MASK 0x00800000U - -/*Byte Lane External VREF Select*/ -#undef DDR_PHY_DX4GCR4_DXREFESEL_DEFVAL -#undef DDR_PHY_DX4GCR4_DXREFESEL_SHIFT -#undef DDR_PHY_DX4GCR4_DXREFESEL_MASK -#define DDR_PHY_DX4GCR4_DXREFESEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_DXREFESEL_SHIFT 16 -#define DDR_PHY_DX4GCR4_DXREFESEL_MASK 0x007F0000U - -/*Single ended VREF generator REFSEL range select*/ -#undef DDR_PHY_DX4GCR4_DXREFSSELRANGE_DEFVAL -#undef DDR_PHY_DX4GCR4_DXREFSSELRANGE_SHIFT -#undef DDR_PHY_DX4GCR4_DXREFSSELRANGE_MASK -#define DDR_PHY_DX4GCR4_DXREFSSELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_DXREFSSELRANGE_SHIFT 15 -#define DDR_PHY_DX4GCR4_DXREFSSELRANGE_MASK 0x00008000U - -/*Byte Lane Single-End VREF Select*/ -#undef DDR_PHY_DX4GCR4_DXREFSSEL_DEFVAL -#undef DDR_PHY_DX4GCR4_DXREFSSEL_SHIFT -#undef DDR_PHY_DX4GCR4_DXREFSSEL_MASK -#define DDR_PHY_DX4GCR4_DXREFSSEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_DXREFSSEL_SHIFT 8 -#define DDR_PHY_DX4GCR4_DXREFSSEL_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX4GCR4_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX4GCR4_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX4GCR4_RESERVED_7_6_MASK -#define DDR_PHY_DX4GCR4_RESERVED_7_6_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX4GCR4_RESERVED_7_6_MASK 0x000000C0U - -/*VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX4GCR4_DXREFIEN_DEFVAL -#undef DDR_PHY_DX4GCR4_DXREFIEN_SHIFT -#undef DDR_PHY_DX4GCR4_DXREFIEN_MASK -#define DDR_PHY_DX4GCR4_DXREFIEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_DXREFIEN_SHIFT 2 -#define DDR_PHY_DX4GCR4_DXREFIEN_MASK 0x0000003CU - -/*VRMON control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX4GCR4_DXREFIMON_DEFVAL -#undef DDR_PHY_DX4GCR4_DXREFIMON_SHIFT -#undef DDR_PHY_DX4GCR4_DXREFIMON_MASK -#define DDR_PHY_DX4GCR4_DXREFIMON_DEFVAL 0x0E00003C -#define DDR_PHY_DX4GCR4_DXREFIMON_SHIFT 0 -#define DDR_PHY_DX4GCR4_DXREFIMON_MASK 0x00000003U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX4GCR5_RESERVED_31_DEFVAL -#undef DDR_PHY_DX4GCR5_RESERVED_31_SHIFT -#undef DDR_PHY_DX4GCR5_RESERVED_31_MASK -#define DDR_PHY_DX4GCR5_RESERVED_31_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR5_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX4GCR5_RESERVED_31_MASK 0x80000000U - -/*Byte Lane internal VREF Select for Rank 3*/ -#undef DDR_PHY_DX4GCR5_DXREFISELR3_DEFVAL -#undef DDR_PHY_DX4GCR5_DXREFISELR3_SHIFT -#undef DDR_PHY_DX4GCR5_DXREFISELR3_MASK -#define DDR_PHY_DX4GCR5_DXREFISELR3_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR5_DXREFISELR3_SHIFT 24 -#define DDR_PHY_DX4GCR5_DXREFISELR3_MASK 0x7F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX4GCR5_RESERVED_23_DEFVAL -#undef DDR_PHY_DX4GCR5_RESERVED_23_SHIFT -#undef DDR_PHY_DX4GCR5_RESERVED_23_MASK -#define DDR_PHY_DX4GCR5_RESERVED_23_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR5_RESERVED_23_SHIFT 23 -#define DDR_PHY_DX4GCR5_RESERVED_23_MASK 0x00800000U - -/*Byte Lane internal VREF Select for Rank 2*/ -#undef DDR_PHY_DX4GCR5_DXREFISELR2_DEFVAL -#undef DDR_PHY_DX4GCR5_DXREFISELR2_SHIFT -#undef DDR_PHY_DX4GCR5_DXREFISELR2_MASK -#define DDR_PHY_DX4GCR5_DXREFISELR2_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR5_DXREFISELR2_SHIFT 16 -#define DDR_PHY_DX4GCR5_DXREFISELR2_MASK 0x007F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX4GCR5_RESERVED_15_DEFVAL -#undef DDR_PHY_DX4GCR5_RESERVED_15_SHIFT -#undef DDR_PHY_DX4GCR5_RESERVED_15_MASK -#define DDR_PHY_DX4GCR5_RESERVED_15_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR5_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX4GCR5_RESERVED_15_MASK 0x00008000U - -/*Byte Lane internal VREF Select for Rank 1*/ -#undef DDR_PHY_DX4GCR5_DXREFISELR1_DEFVAL -#undef DDR_PHY_DX4GCR5_DXREFISELR1_SHIFT -#undef DDR_PHY_DX4GCR5_DXREFISELR1_MASK -#define DDR_PHY_DX4GCR5_DXREFISELR1_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR5_DXREFISELR1_SHIFT 8 -#define DDR_PHY_DX4GCR5_DXREFISELR1_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX4GCR5_RESERVED_7_DEFVAL -#undef DDR_PHY_DX4GCR5_RESERVED_7_SHIFT -#undef DDR_PHY_DX4GCR5_RESERVED_7_MASK -#define DDR_PHY_DX4GCR5_RESERVED_7_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR5_RESERVED_7_SHIFT 7 -#define DDR_PHY_DX4GCR5_RESERVED_7_MASK 0x00000080U - -/*Byte Lane internal VREF Select for Rank 0*/ -#undef DDR_PHY_DX4GCR5_DXREFISELR0_DEFVAL -#undef DDR_PHY_DX4GCR5_DXREFISELR0_SHIFT -#undef DDR_PHY_DX4GCR5_DXREFISELR0_MASK -#define DDR_PHY_DX4GCR5_DXREFISELR0_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR5_DXREFISELR0_SHIFT 0 -#define DDR_PHY_DX4GCR5_DXREFISELR0_MASK 0x0000007FU - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX4GCR6_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX4GCR6_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX4GCR6_RESERVED_31_30_MASK -#define DDR_PHY_DX4GCR6_RESERVED_31_30_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR6_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX4GCR6_RESERVED_31_30_MASK 0xC0000000U - -/*DRAM DQ VREF Select for Rank3*/ -#undef DDR_PHY_DX4GCR6_DXDQVREFR3_DEFVAL -#undef DDR_PHY_DX4GCR6_DXDQVREFR3_SHIFT -#undef DDR_PHY_DX4GCR6_DXDQVREFR3_MASK -#define DDR_PHY_DX4GCR6_DXDQVREFR3_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR6_DXDQVREFR3_SHIFT 24 -#define DDR_PHY_DX4GCR6_DXDQVREFR3_MASK 0x3F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX4GCR6_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX4GCR6_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX4GCR6_RESERVED_23_22_MASK -#define DDR_PHY_DX4GCR6_RESERVED_23_22_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR6_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX4GCR6_RESERVED_23_22_MASK 0x00C00000U - -/*DRAM DQ VREF Select for Rank2*/ -#undef DDR_PHY_DX4GCR6_DXDQVREFR2_DEFVAL -#undef DDR_PHY_DX4GCR6_DXDQVREFR2_SHIFT -#undef DDR_PHY_DX4GCR6_DXDQVREFR2_MASK -#define DDR_PHY_DX4GCR6_DXDQVREFR2_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR6_DXDQVREFR2_SHIFT 16 -#define DDR_PHY_DX4GCR6_DXDQVREFR2_MASK 0x003F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX4GCR6_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DX4GCR6_RESERVED_15_14_SHIFT -#undef DDR_PHY_DX4GCR6_RESERVED_15_14_MASK -#define DDR_PHY_DX4GCR6_RESERVED_15_14_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR6_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DX4GCR6_RESERVED_15_14_MASK 0x0000C000U - -/*DRAM DQ VREF Select for Rank1*/ -#undef DDR_PHY_DX4GCR6_DXDQVREFR1_DEFVAL -#undef DDR_PHY_DX4GCR6_DXDQVREFR1_SHIFT -#undef DDR_PHY_DX4GCR6_DXDQVREFR1_MASK -#define DDR_PHY_DX4GCR6_DXDQVREFR1_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR6_DXDQVREFR1_SHIFT 8 -#define DDR_PHY_DX4GCR6_DXDQVREFR1_MASK 0x00003F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX4GCR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX4GCR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX4GCR6_RESERVED_7_6_MASK -#define DDR_PHY_DX4GCR6_RESERVED_7_6_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX4GCR6_RESERVED_7_6_MASK 0x000000C0U - -/*DRAM DQ VREF Select for Rank0*/ -#undef DDR_PHY_DX4GCR6_DXDQVREFR0_DEFVAL -#undef DDR_PHY_DX4GCR6_DXDQVREFR0_SHIFT -#undef DDR_PHY_DX4GCR6_DXDQVREFR0_MASK -#define DDR_PHY_DX4GCR6_DXDQVREFR0_DEFVAL 0x09090909 -#define DDR_PHY_DX4GCR6_DXDQVREFR0_SHIFT 0 -#define DDR_PHY_DX4GCR6_DXDQVREFR0_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX4LCDLR2_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX4LCDLR2_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX4LCDLR2_RESERVED_31_25_MASK -#define DDR_PHY_DX4LCDLR2_RESERVED_31_25_DEFVAL 0x00000000 -#define DDR_PHY_DX4LCDLR2_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX4LCDLR2_RESERVED_31_25_MASK 0xFE000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX4LCDLR2_RESERVED_24_16_DEFVAL -#undef DDR_PHY_DX4LCDLR2_RESERVED_24_16_SHIFT -#undef DDR_PHY_DX4LCDLR2_RESERVED_24_16_MASK -#define DDR_PHY_DX4LCDLR2_RESERVED_24_16_DEFVAL 0x00000000 -#define DDR_PHY_DX4LCDLR2_RESERVED_24_16_SHIFT 16 -#define DDR_PHY_DX4LCDLR2_RESERVED_24_16_MASK 0x01FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX4LCDLR2_RESERVED_15_9_DEFVAL -#undef DDR_PHY_DX4LCDLR2_RESERVED_15_9_SHIFT -#undef DDR_PHY_DX4LCDLR2_RESERVED_15_9_MASK -#define DDR_PHY_DX4LCDLR2_RESERVED_15_9_DEFVAL 0x00000000 -#define DDR_PHY_DX4LCDLR2_RESERVED_15_9_SHIFT 9 -#define DDR_PHY_DX4LCDLR2_RESERVED_15_9_MASK 0x0000FE00U - -/*Read DQS Gating Delay*/ -#undef DDR_PHY_DX4LCDLR2_DQSGD_DEFVAL -#undef DDR_PHY_DX4LCDLR2_DQSGD_SHIFT -#undef DDR_PHY_DX4LCDLR2_DQSGD_MASK -#define DDR_PHY_DX4LCDLR2_DQSGD_DEFVAL 0x00000000 -#define DDR_PHY_DX4LCDLR2_DQSGD_SHIFT 0 -#define DDR_PHY_DX4LCDLR2_DQSGD_MASK 0x000001FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX4GTR0_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX4GTR0_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX4GTR0_RESERVED_31_24_MASK -#define DDR_PHY_DX4GTR0_RESERVED_31_24_DEFVAL 0x00020000 -#define DDR_PHY_DX4GTR0_RESERVED_31_24_SHIFT 27 -#define DDR_PHY_DX4GTR0_RESERVED_31_24_MASK 0xF8000000U - -/*DQ Write Path Latency Pipeline*/ -#undef DDR_PHY_DX4GTR0_WDQSL_DEFVAL -#undef DDR_PHY_DX4GTR0_WDQSL_SHIFT -#undef DDR_PHY_DX4GTR0_WDQSL_MASK -#define DDR_PHY_DX4GTR0_WDQSL_DEFVAL 0x00020000 -#define DDR_PHY_DX4GTR0_WDQSL_SHIFT 24 -#define DDR_PHY_DX4GTR0_WDQSL_MASK 0x07000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX4GTR0_RESERVED_23_20_DEFVAL -#undef DDR_PHY_DX4GTR0_RESERVED_23_20_SHIFT -#undef DDR_PHY_DX4GTR0_RESERVED_23_20_MASK -#define DDR_PHY_DX4GTR0_RESERVED_23_20_DEFVAL 0x00020000 -#define DDR_PHY_DX4GTR0_RESERVED_23_20_SHIFT 20 -#define DDR_PHY_DX4GTR0_RESERVED_23_20_MASK 0x00F00000U - -/*Write Leveling System Latency*/ -#undef DDR_PHY_DX4GTR0_WLSL_DEFVAL -#undef DDR_PHY_DX4GTR0_WLSL_SHIFT -#undef DDR_PHY_DX4GTR0_WLSL_MASK -#define DDR_PHY_DX4GTR0_WLSL_DEFVAL 0x00020000 -#define DDR_PHY_DX4GTR0_WLSL_SHIFT 16 -#define DDR_PHY_DX4GTR0_WLSL_MASK 0x000F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX4GTR0_RESERVED_15_13_DEFVAL -#undef DDR_PHY_DX4GTR0_RESERVED_15_13_SHIFT -#undef DDR_PHY_DX4GTR0_RESERVED_15_13_MASK -#define DDR_PHY_DX4GTR0_RESERVED_15_13_DEFVAL 0x00020000 -#define DDR_PHY_DX4GTR0_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_DX4GTR0_RESERVED_15_13_MASK 0x0000E000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX4GTR0_RESERVED_12_8_DEFVAL -#undef DDR_PHY_DX4GTR0_RESERVED_12_8_SHIFT -#undef DDR_PHY_DX4GTR0_RESERVED_12_8_MASK -#define DDR_PHY_DX4GTR0_RESERVED_12_8_DEFVAL 0x00020000 -#define DDR_PHY_DX4GTR0_RESERVED_12_8_SHIFT 8 -#define DDR_PHY_DX4GTR0_RESERVED_12_8_MASK 0x00001F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX4GTR0_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DX4GTR0_RESERVED_7_5_SHIFT -#undef DDR_PHY_DX4GTR0_RESERVED_7_5_MASK -#define DDR_PHY_DX4GTR0_RESERVED_7_5_DEFVAL 0x00020000 -#define DDR_PHY_DX4GTR0_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DX4GTR0_RESERVED_7_5_MASK 0x000000E0U - -/*DQS Gating System Latency*/ -#undef DDR_PHY_DX4GTR0_DGSL_DEFVAL -#undef DDR_PHY_DX4GTR0_DGSL_SHIFT -#undef DDR_PHY_DX4GTR0_DGSL_MASK -#define DDR_PHY_DX4GTR0_DGSL_DEFVAL 0x00020000 -#define DDR_PHY_DX4GTR0_DGSL_SHIFT 0 -#define DDR_PHY_DX4GTR0_DGSL_MASK 0x0000001FU - -/*Calibration Bypass*/ -#undef DDR_PHY_DX5GCR0_CALBYP_DEFVAL -#undef DDR_PHY_DX5GCR0_CALBYP_SHIFT -#undef DDR_PHY_DX5GCR0_CALBYP_MASK -#define DDR_PHY_DX5GCR0_CALBYP_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_CALBYP_SHIFT 31 -#define DDR_PHY_DX5GCR0_CALBYP_MASK 0x80000000U - -/*Master Delay Line Enable*/ -#undef DDR_PHY_DX5GCR0_MDLEN_DEFVAL -#undef DDR_PHY_DX5GCR0_MDLEN_SHIFT -#undef DDR_PHY_DX5GCR0_MDLEN_MASK -#define DDR_PHY_DX5GCR0_MDLEN_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_MDLEN_SHIFT 30 -#define DDR_PHY_DX5GCR0_MDLEN_MASK 0x40000000U - -/*Configurable ODT(TE) Phase Shift*/ -#undef DDR_PHY_DX5GCR0_CODTSHFT_DEFVAL -#undef DDR_PHY_DX5GCR0_CODTSHFT_SHIFT -#undef DDR_PHY_DX5GCR0_CODTSHFT_MASK -#define DDR_PHY_DX5GCR0_CODTSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_CODTSHFT_SHIFT 28 -#define DDR_PHY_DX5GCR0_CODTSHFT_MASK 0x30000000U - -/*DQS Duty Cycle Correction*/ -#undef DDR_PHY_DX5GCR0_DQSDCC_DEFVAL -#undef DDR_PHY_DX5GCR0_DQSDCC_SHIFT -#undef DDR_PHY_DX5GCR0_DQSDCC_MASK -#define DDR_PHY_DX5GCR0_DQSDCC_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_DQSDCC_SHIFT 24 -#define DDR_PHY_DX5GCR0_DQSDCC_MASK 0x0F000000U - -/*Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY*/ -#undef DDR_PHY_DX5GCR0_RDDLY_DEFVAL -#undef DDR_PHY_DX5GCR0_RDDLY_SHIFT -#undef DDR_PHY_DX5GCR0_RDDLY_MASK -#define DDR_PHY_DX5GCR0_RDDLY_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_RDDLY_SHIFT 20 -#define DDR_PHY_DX5GCR0_RDDLY_MASK 0x00F00000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX5GCR0_RESERVED_19_14_DEFVAL -#undef DDR_PHY_DX5GCR0_RESERVED_19_14_SHIFT -#undef DDR_PHY_DX5GCR0_RESERVED_19_14_MASK -#define DDR_PHY_DX5GCR0_RESERVED_19_14_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_RESERVED_19_14_SHIFT 14 -#define DDR_PHY_DX5GCR0_RESERVED_19_14_MASK 0x000FC000U - -/*DQSNSE Power Down Receiver*/ -#undef DDR_PHY_DX5GCR0_DQSNSEPDR_DEFVAL -#undef DDR_PHY_DX5GCR0_DQSNSEPDR_SHIFT -#undef DDR_PHY_DX5GCR0_DQSNSEPDR_MASK -#define DDR_PHY_DX5GCR0_DQSNSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_DQSNSEPDR_SHIFT 13 -#define DDR_PHY_DX5GCR0_DQSNSEPDR_MASK 0x00002000U - -/*DQSSE Power Down Receiver*/ -#undef DDR_PHY_DX5GCR0_DQSSEPDR_DEFVAL -#undef DDR_PHY_DX5GCR0_DQSSEPDR_SHIFT -#undef DDR_PHY_DX5GCR0_DQSSEPDR_MASK -#define DDR_PHY_DX5GCR0_DQSSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_DQSSEPDR_SHIFT 12 -#define DDR_PHY_DX5GCR0_DQSSEPDR_MASK 0x00001000U - -/*RTT On Additive Latency*/ -#undef DDR_PHY_DX5GCR0_RTTOAL_DEFVAL -#undef DDR_PHY_DX5GCR0_RTTOAL_SHIFT -#undef DDR_PHY_DX5GCR0_RTTOAL_MASK -#define DDR_PHY_DX5GCR0_RTTOAL_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_RTTOAL_SHIFT 11 -#define DDR_PHY_DX5GCR0_RTTOAL_MASK 0x00000800U - -/*RTT Output Hold*/ -#undef DDR_PHY_DX5GCR0_RTTOH_DEFVAL -#undef DDR_PHY_DX5GCR0_RTTOH_SHIFT -#undef DDR_PHY_DX5GCR0_RTTOH_MASK -#define DDR_PHY_DX5GCR0_RTTOH_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_RTTOH_SHIFT 9 -#define DDR_PHY_DX5GCR0_RTTOH_MASK 0x00000600U - -/*Configurable PDR Phase Shift*/ -#undef DDR_PHY_DX5GCR0_CPDRSHFT_DEFVAL -#undef DDR_PHY_DX5GCR0_CPDRSHFT_SHIFT -#undef DDR_PHY_DX5GCR0_CPDRSHFT_MASK -#define DDR_PHY_DX5GCR0_CPDRSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_CPDRSHFT_SHIFT 7 -#define DDR_PHY_DX5GCR0_CPDRSHFT_MASK 0x00000180U - -/*DQSR Power Down*/ -#undef DDR_PHY_DX5GCR0_DQSRPD_DEFVAL -#undef DDR_PHY_DX5GCR0_DQSRPD_SHIFT -#undef DDR_PHY_DX5GCR0_DQSRPD_MASK -#define DDR_PHY_DX5GCR0_DQSRPD_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_DQSRPD_SHIFT 6 -#define DDR_PHY_DX5GCR0_DQSRPD_MASK 0x00000040U - -/*DQSG Power Down Receiver*/ -#undef DDR_PHY_DX5GCR0_DQSGPDR_DEFVAL -#undef DDR_PHY_DX5GCR0_DQSGPDR_SHIFT -#undef DDR_PHY_DX5GCR0_DQSGPDR_MASK -#define DDR_PHY_DX5GCR0_DQSGPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_DQSGPDR_SHIFT 5 -#define DDR_PHY_DX5GCR0_DQSGPDR_MASK 0x00000020U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX5GCR0_RESERVED_4_DEFVAL -#undef DDR_PHY_DX5GCR0_RESERVED_4_SHIFT -#undef DDR_PHY_DX5GCR0_RESERVED_4_MASK -#define DDR_PHY_DX5GCR0_RESERVED_4_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_RESERVED_4_SHIFT 4 -#define DDR_PHY_DX5GCR0_RESERVED_4_MASK 0x00000010U - -/*DQSG On-Die Termination*/ -#undef DDR_PHY_DX5GCR0_DQSGODT_DEFVAL -#undef DDR_PHY_DX5GCR0_DQSGODT_SHIFT -#undef DDR_PHY_DX5GCR0_DQSGODT_MASK -#define DDR_PHY_DX5GCR0_DQSGODT_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_DQSGODT_SHIFT 3 -#define DDR_PHY_DX5GCR0_DQSGODT_MASK 0x00000008U - -/*DQSG Output Enable*/ -#undef DDR_PHY_DX5GCR0_DQSGOE_DEFVAL -#undef DDR_PHY_DX5GCR0_DQSGOE_SHIFT -#undef DDR_PHY_DX5GCR0_DQSGOE_MASK -#define DDR_PHY_DX5GCR0_DQSGOE_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_DQSGOE_SHIFT 2 -#define DDR_PHY_DX5GCR0_DQSGOE_MASK 0x00000004U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX5GCR0_RESERVED_1_0_DEFVAL -#undef DDR_PHY_DX5GCR0_RESERVED_1_0_SHIFT -#undef DDR_PHY_DX5GCR0_RESERVED_1_0_MASK -#define DDR_PHY_DX5GCR0_RESERVED_1_0_DEFVAL 0x40200204 -#define DDR_PHY_DX5GCR0_RESERVED_1_0_SHIFT 0 -#define DDR_PHY_DX5GCR0_RESERVED_1_0_MASK 0x00000003U - -/*Enables the PDR mode for DQ[7:0]*/ -#undef DDR_PHY_DX5GCR1_DXPDRMODE_DEFVAL -#undef DDR_PHY_DX5GCR1_DXPDRMODE_SHIFT -#undef DDR_PHY_DX5GCR1_DXPDRMODE_MASK -#define DDR_PHY_DX5GCR1_DXPDRMODE_DEFVAL 0x00007FFF -#define DDR_PHY_DX5GCR1_DXPDRMODE_SHIFT 16 -#define DDR_PHY_DX5GCR1_DXPDRMODE_MASK 0xFFFF0000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_DX5GCR1_RESERVED_15_DEFVAL -#undef DDR_PHY_DX5GCR1_RESERVED_15_SHIFT -#undef DDR_PHY_DX5GCR1_RESERVED_15_MASK -#define DDR_PHY_DX5GCR1_RESERVED_15_DEFVAL 0x00007FFF -#define DDR_PHY_DX5GCR1_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX5GCR1_RESERVED_15_MASK 0x00008000U - -/*Select the delayed or non-delayed read data strobe #*/ -#undef DDR_PHY_DX5GCR1_QSNSEL_DEFVAL -#undef DDR_PHY_DX5GCR1_QSNSEL_SHIFT -#undef DDR_PHY_DX5GCR1_QSNSEL_MASK -#define DDR_PHY_DX5GCR1_QSNSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX5GCR1_QSNSEL_SHIFT 14 -#define DDR_PHY_DX5GCR1_QSNSEL_MASK 0x00004000U - -/*Select the delayed or non-delayed read data strobe*/ -#undef DDR_PHY_DX5GCR1_QSSEL_DEFVAL -#undef DDR_PHY_DX5GCR1_QSSEL_SHIFT -#undef DDR_PHY_DX5GCR1_QSSEL_MASK -#define DDR_PHY_DX5GCR1_QSSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX5GCR1_QSSEL_SHIFT 13 -#define DDR_PHY_DX5GCR1_QSSEL_MASK 0x00002000U - -/*Enables Read Data Strobe in a byte lane*/ -#undef DDR_PHY_DX5GCR1_OEEN_DEFVAL -#undef DDR_PHY_DX5GCR1_OEEN_SHIFT -#undef DDR_PHY_DX5GCR1_OEEN_MASK -#define DDR_PHY_DX5GCR1_OEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX5GCR1_OEEN_SHIFT 12 -#define DDR_PHY_DX5GCR1_OEEN_MASK 0x00001000U - -/*Enables PDR in a byte lane*/ -#undef DDR_PHY_DX5GCR1_PDREN_DEFVAL -#undef DDR_PHY_DX5GCR1_PDREN_SHIFT -#undef DDR_PHY_DX5GCR1_PDREN_MASK -#define DDR_PHY_DX5GCR1_PDREN_DEFVAL 0x00007FFF -#define DDR_PHY_DX5GCR1_PDREN_SHIFT 11 -#define DDR_PHY_DX5GCR1_PDREN_MASK 0x00000800U - -/*Enables ODT/TE in a byte lane*/ -#undef DDR_PHY_DX5GCR1_TEEN_DEFVAL -#undef DDR_PHY_DX5GCR1_TEEN_SHIFT -#undef DDR_PHY_DX5GCR1_TEEN_MASK -#define DDR_PHY_DX5GCR1_TEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX5GCR1_TEEN_SHIFT 10 -#define DDR_PHY_DX5GCR1_TEEN_MASK 0x00000400U - -/*Enables Write Data strobe in a byte lane*/ -#undef DDR_PHY_DX5GCR1_DSEN_DEFVAL -#undef DDR_PHY_DX5GCR1_DSEN_SHIFT -#undef DDR_PHY_DX5GCR1_DSEN_MASK -#define DDR_PHY_DX5GCR1_DSEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX5GCR1_DSEN_SHIFT 9 -#define DDR_PHY_DX5GCR1_DSEN_MASK 0x00000200U - -/*Enables DM pin in a byte lane*/ -#undef DDR_PHY_DX5GCR1_DMEN_DEFVAL -#undef DDR_PHY_DX5GCR1_DMEN_SHIFT -#undef DDR_PHY_DX5GCR1_DMEN_MASK -#define DDR_PHY_DX5GCR1_DMEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX5GCR1_DMEN_SHIFT 8 -#define DDR_PHY_DX5GCR1_DMEN_MASK 0x00000100U - -/*Enables DQ corresponding to each bit in a byte*/ -#undef DDR_PHY_DX5GCR1_DQEN_DEFVAL -#undef DDR_PHY_DX5GCR1_DQEN_SHIFT -#undef DDR_PHY_DX5GCR1_DQEN_MASK -#define DDR_PHY_DX5GCR1_DQEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX5GCR1_DQEN_SHIFT 0 -#define DDR_PHY_DX5GCR1_DQEN_MASK 0x000000FFU - -/*Byte lane VREF IOM (Used only by D4MU IOs)*/ -#undef DDR_PHY_DX5GCR4_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DX5GCR4_RESERVED_31_29_SHIFT -#undef DDR_PHY_DX5GCR4_RESERVED_31_29_MASK -#define DDR_PHY_DX5GCR4_RESERVED_31_29_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DX5GCR4_RESERVED_31_29_MASK 0xE0000000U - -/*Byte Lane VREF Pad Enable*/ -#undef DDR_PHY_DX5GCR4_DXREFPEN_DEFVAL -#undef DDR_PHY_DX5GCR4_DXREFPEN_SHIFT -#undef DDR_PHY_DX5GCR4_DXREFPEN_MASK -#define DDR_PHY_DX5GCR4_DXREFPEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_DXREFPEN_SHIFT 28 -#define DDR_PHY_DX5GCR4_DXREFPEN_MASK 0x10000000U - -/*Byte Lane Internal VREF Enable*/ -#undef DDR_PHY_DX5GCR4_DXREFEEN_DEFVAL -#undef DDR_PHY_DX5GCR4_DXREFEEN_SHIFT -#undef DDR_PHY_DX5GCR4_DXREFEEN_MASK -#define DDR_PHY_DX5GCR4_DXREFEEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_DXREFEEN_SHIFT 26 -#define DDR_PHY_DX5GCR4_DXREFEEN_MASK 0x0C000000U - -/*Byte Lane Single-End VREF Enable*/ -#undef DDR_PHY_DX5GCR4_DXREFSEN_DEFVAL -#undef DDR_PHY_DX5GCR4_DXREFSEN_SHIFT -#undef DDR_PHY_DX5GCR4_DXREFSEN_MASK -#define DDR_PHY_DX5GCR4_DXREFSEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_DXREFSEN_SHIFT 25 -#define DDR_PHY_DX5GCR4_DXREFSEN_MASK 0x02000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX5GCR4_RESERVED_24_DEFVAL -#undef DDR_PHY_DX5GCR4_RESERVED_24_SHIFT -#undef DDR_PHY_DX5GCR4_RESERVED_24_MASK -#define DDR_PHY_DX5GCR4_RESERVED_24_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_RESERVED_24_SHIFT 24 -#define DDR_PHY_DX5GCR4_RESERVED_24_MASK 0x01000000U - -/*External VREF generator REFSEL range select*/ -#undef DDR_PHY_DX5GCR4_DXREFESELRANGE_DEFVAL -#undef DDR_PHY_DX5GCR4_DXREFESELRANGE_SHIFT -#undef DDR_PHY_DX5GCR4_DXREFESELRANGE_MASK -#define DDR_PHY_DX5GCR4_DXREFESELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_DXREFESELRANGE_SHIFT 23 -#define DDR_PHY_DX5GCR4_DXREFESELRANGE_MASK 0x00800000U - -/*Byte Lane External VREF Select*/ -#undef DDR_PHY_DX5GCR4_DXREFESEL_DEFVAL -#undef DDR_PHY_DX5GCR4_DXREFESEL_SHIFT -#undef DDR_PHY_DX5GCR4_DXREFESEL_MASK -#define DDR_PHY_DX5GCR4_DXREFESEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_DXREFESEL_SHIFT 16 -#define DDR_PHY_DX5GCR4_DXREFESEL_MASK 0x007F0000U - -/*Single ended VREF generator REFSEL range select*/ -#undef DDR_PHY_DX5GCR4_DXREFSSELRANGE_DEFVAL -#undef DDR_PHY_DX5GCR4_DXREFSSELRANGE_SHIFT -#undef DDR_PHY_DX5GCR4_DXREFSSELRANGE_MASK -#define DDR_PHY_DX5GCR4_DXREFSSELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_DXREFSSELRANGE_SHIFT 15 -#define DDR_PHY_DX5GCR4_DXREFSSELRANGE_MASK 0x00008000U - -/*Byte Lane Single-End VREF Select*/ -#undef DDR_PHY_DX5GCR4_DXREFSSEL_DEFVAL -#undef DDR_PHY_DX5GCR4_DXREFSSEL_SHIFT -#undef DDR_PHY_DX5GCR4_DXREFSSEL_MASK -#define DDR_PHY_DX5GCR4_DXREFSSEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_DXREFSSEL_SHIFT 8 -#define DDR_PHY_DX5GCR4_DXREFSSEL_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX5GCR4_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX5GCR4_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX5GCR4_RESERVED_7_6_MASK -#define DDR_PHY_DX5GCR4_RESERVED_7_6_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX5GCR4_RESERVED_7_6_MASK 0x000000C0U - -/*VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX5GCR4_DXREFIEN_DEFVAL -#undef DDR_PHY_DX5GCR4_DXREFIEN_SHIFT -#undef DDR_PHY_DX5GCR4_DXREFIEN_MASK -#define DDR_PHY_DX5GCR4_DXREFIEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_DXREFIEN_SHIFT 2 -#define DDR_PHY_DX5GCR4_DXREFIEN_MASK 0x0000003CU - -/*VRMON control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX5GCR4_DXREFIMON_DEFVAL -#undef DDR_PHY_DX5GCR4_DXREFIMON_SHIFT -#undef DDR_PHY_DX5GCR4_DXREFIMON_MASK -#define DDR_PHY_DX5GCR4_DXREFIMON_DEFVAL 0x0E00003C -#define DDR_PHY_DX5GCR4_DXREFIMON_SHIFT 0 -#define DDR_PHY_DX5GCR4_DXREFIMON_MASK 0x00000003U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX5GCR5_RESERVED_31_DEFVAL -#undef DDR_PHY_DX5GCR5_RESERVED_31_SHIFT -#undef DDR_PHY_DX5GCR5_RESERVED_31_MASK -#define DDR_PHY_DX5GCR5_RESERVED_31_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR5_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX5GCR5_RESERVED_31_MASK 0x80000000U - -/*Byte Lane internal VREF Select for Rank 3*/ -#undef DDR_PHY_DX5GCR5_DXREFISELR3_DEFVAL -#undef DDR_PHY_DX5GCR5_DXREFISELR3_SHIFT -#undef DDR_PHY_DX5GCR5_DXREFISELR3_MASK -#define DDR_PHY_DX5GCR5_DXREFISELR3_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR5_DXREFISELR3_SHIFT 24 -#define DDR_PHY_DX5GCR5_DXREFISELR3_MASK 0x7F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX5GCR5_RESERVED_23_DEFVAL -#undef DDR_PHY_DX5GCR5_RESERVED_23_SHIFT -#undef DDR_PHY_DX5GCR5_RESERVED_23_MASK -#define DDR_PHY_DX5GCR5_RESERVED_23_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR5_RESERVED_23_SHIFT 23 -#define DDR_PHY_DX5GCR5_RESERVED_23_MASK 0x00800000U - -/*Byte Lane internal VREF Select for Rank 2*/ -#undef DDR_PHY_DX5GCR5_DXREFISELR2_DEFVAL -#undef DDR_PHY_DX5GCR5_DXREFISELR2_SHIFT -#undef DDR_PHY_DX5GCR5_DXREFISELR2_MASK -#define DDR_PHY_DX5GCR5_DXREFISELR2_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR5_DXREFISELR2_SHIFT 16 -#define DDR_PHY_DX5GCR5_DXREFISELR2_MASK 0x007F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX5GCR5_RESERVED_15_DEFVAL -#undef DDR_PHY_DX5GCR5_RESERVED_15_SHIFT -#undef DDR_PHY_DX5GCR5_RESERVED_15_MASK -#define DDR_PHY_DX5GCR5_RESERVED_15_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR5_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX5GCR5_RESERVED_15_MASK 0x00008000U - -/*Byte Lane internal VREF Select for Rank 1*/ -#undef DDR_PHY_DX5GCR5_DXREFISELR1_DEFVAL -#undef DDR_PHY_DX5GCR5_DXREFISELR1_SHIFT -#undef DDR_PHY_DX5GCR5_DXREFISELR1_MASK -#define DDR_PHY_DX5GCR5_DXREFISELR1_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR5_DXREFISELR1_SHIFT 8 -#define DDR_PHY_DX5GCR5_DXREFISELR1_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX5GCR5_RESERVED_7_DEFVAL -#undef DDR_PHY_DX5GCR5_RESERVED_7_SHIFT -#undef DDR_PHY_DX5GCR5_RESERVED_7_MASK -#define DDR_PHY_DX5GCR5_RESERVED_7_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR5_RESERVED_7_SHIFT 7 -#define DDR_PHY_DX5GCR5_RESERVED_7_MASK 0x00000080U - -/*Byte Lane internal VREF Select for Rank 0*/ -#undef DDR_PHY_DX5GCR5_DXREFISELR0_DEFVAL -#undef DDR_PHY_DX5GCR5_DXREFISELR0_SHIFT -#undef DDR_PHY_DX5GCR5_DXREFISELR0_MASK -#define DDR_PHY_DX5GCR5_DXREFISELR0_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR5_DXREFISELR0_SHIFT 0 -#define DDR_PHY_DX5GCR5_DXREFISELR0_MASK 0x0000007FU - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX5GCR6_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX5GCR6_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX5GCR6_RESERVED_31_30_MASK -#define DDR_PHY_DX5GCR6_RESERVED_31_30_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR6_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX5GCR6_RESERVED_31_30_MASK 0xC0000000U - -/*DRAM DQ VREF Select for Rank3*/ -#undef DDR_PHY_DX5GCR6_DXDQVREFR3_DEFVAL -#undef DDR_PHY_DX5GCR6_DXDQVREFR3_SHIFT -#undef DDR_PHY_DX5GCR6_DXDQVREFR3_MASK -#define DDR_PHY_DX5GCR6_DXDQVREFR3_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR6_DXDQVREFR3_SHIFT 24 -#define DDR_PHY_DX5GCR6_DXDQVREFR3_MASK 0x3F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX5GCR6_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX5GCR6_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX5GCR6_RESERVED_23_22_MASK -#define DDR_PHY_DX5GCR6_RESERVED_23_22_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR6_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX5GCR6_RESERVED_23_22_MASK 0x00C00000U - -/*DRAM DQ VREF Select for Rank2*/ -#undef DDR_PHY_DX5GCR6_DXDQVREFR2_DEFVAL -#undef DDR_PHY_DX5GCR6_DXDQVREFR2_SHIFT -#undef DDR_PHY_DX5GCR6_DXDQVREFR2_MASK -#define DDR_PHY_DX5GCR6_DXDQVREFR2_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR6_DXDQVREFR2_SHIFT 16 -#define DDR_PHY_DX5GCR6_DXDQVREFR2_MASK 0x003F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX5GCR6_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DX5GCR6_RESERVED_15_14_SHIFT -#undef DDR_PHY_DX5GCR6_RESERVED_15_14_MASK -#define DDR_PHY_DX5GCR6_RESERVED_15_14_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR6_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DX5GCR6_RESERVED_15_14_MASK 0x0000C000U - -/*DRAM DQ VREF Select for Rank1*/ -#undef DDR_PHY_DX5GCR6_DXDQVREFR1_DEFVAL -#undef DDR_PHY_DX5GCR6_DXDQVREFR1_SHIFT -#undef DDR_PHY_DX5GCR6_DXDQVREFR1_MASK -#define DDR_PHY_DX5GCR6_DXDQVREFR1_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR6_DXDQVREFR1_SHIFT 8 -#define DDR_PHY_DX5GCR6_DXDQVREFR1_MASK 0x00003F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX5GCR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX5GCR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX5GCR6_RESERVED_7_6_MASK -#define DDR_PHY_DX5GCR6_RESERVED_7_6_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX5GCR6_RESERVED_7_6_MASK 0x000000C0U - -/*DRAM DQ VREF Select for Rank0*/ -#undef DDR_PHY_DX5GCR6_DXDQVREFR0_DEFVAL -#undef DDR_PHY_DX5GCR6_DXDQVREFR0_SHIFT -#undef DDR_PHY_DX5GCR6_DXDQVREFR0_MASK -#define DDR_PHY_DX5GCR6_DXDQVREFR0_DEFVAL 0x09090909 -#define DDR_PHY_DX5GCR6_DXDQVREFR0_SHIFT 0 -#define DDR_PHY_DX5GCR6_DXDQVREFR0_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX5LCDLR2_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX5LCDLR2_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX5LCDLR2_RESERVED_31_25_MASK -#define DDR_PHY_DX5LCDLR2_RESERVED_31_25_DEFVAL 0x00000000 -#define DDR_PHY_DX5LCDLR2_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX5LCDLR2_RESERVED_31_25_MASK 0xFE000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX5LCDLR2_RESERVED_24_16_DEFVAL -#undef DDR_PHY_DX5LCDLR2_RESERVED_24_16_SHIFT -#undef DDR_PHY_DX5LCDLR2_RESERVED_24_16_MASK -#define DDR_PHY_DX5LCDLR2_RESERVED_24_16_DEFVAL 0x00000000 -#define DDR_PHY_DX5LCDLR2_RESERVED_24_16_SHIFT 16 -#define DDR_PHY_DX5LCDLR2_RESERVED_24_16_MASK 0x01FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX5LCDLR2_RESERVED_15_9_DEFVAL -#undef DDR_PHY_DX5LCDLR2_RESERVED_15_9_SHIFT -#undef DDR_PHY_DX5LCDLR2_RESERVED_15_9_MASK -#define DDR_PHY_DX5LCDLR2_RESERVED_15_9_DEFVAL 0x00000000 -#define DDR_PHY_DX5LCDLR2_RESERVED_15_9_SHIFT 9 -#define DDR_PHY_DX5LCDLR2_RESERVED_15_9_MASK 0x0000FE00U - -/*Read DQS Gating Delay*/ -#undef DDR_PHY_DX5LCDLR2_DQSGD_DEFVAL -#undef DDR_PHY_DX5LCDLR2_DQSGD_SHIFT -#undef DDR_PHY_DX5LCDLR2_DQSGD_MASK -#define DDR_PHY_DX5LCDLR2_DQSGD_DEFVAL 0x00000000 -#define DDR_PHY_DX5LCDLR2_DQSGD_SHIFT 0 -#define DDR_PHY_DX5LCDLR2_DQSGD_MASK 0x000001FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX5GTR0_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX5GTR0_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX5GTR0_RESERVED_31_24_MASK -#define DDR_PHY_DX5GTR0_RESERVED_31_24_DEFVAL 0x00020000 -#define DDR_PHY_DX5GTR0_RESERVED_31_24_SHIFT 27 -#define DDR_PHY_DX5GTR0_RESERVED_31_24_MASK 0xF8000000U - -/*DQ Write Path Latency Pipeline*/ -#undef DDR_PHY_DX5GTR0_WDQSL_DEFVAL -#undef DDR_PHY_DX5GTR0_WDQSL_SHIFT -#undef DDR_PHY_DX5GTR0_WDQSL_MASK -#define DDR_PHY_DX5GTR0_WDQSL_DEFVAL 0x00020000 -#define DDR_PHY_DX5GTR0_WDQSL_SHIFT 24 -#define DDR_PHY_DX5GTR0_WDQSL_MASK 0x07000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX5GTR0_RESERVED_23_20_DEFVAL -#undef DDR_PHY_DX5GTR0_RESERVED_23_20_SHIFT -#undef DDR_PHY_DX5GTR0_RESERVED_23_20_MASK -#define DDR_PHY_DX5GTR0_RESERVED_23_20_DEFVAL 0x00020000 -#define DDR_PHY_DX5GTR0_RESERVED_23_20_SHIFT 20 -#define DDR_PHY_DX5GTR0_RESERVED_23_20_MASK 0x00F00000U - -/*Write Leveling System Latency*/ -#undef DDR_PHY_DX5GTR0_WLSL_DEFVAL -#undef DDR_PHY_DX5GTR0_WLSL_SHIFT -#undef DDR_PHY_DX5GTR0_WLSL_MASK -#define DDR_PHY_DX5GTR0_WLSL_DEFVAL 0x00020000 -#define DDR_PHY_DX5GTR0_WLSL_SHIFT 16 -#define DDR_PHY_DX5GTR0_WLSL_MASK 0x000F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX5GTR0_RESERVED_15_13_DEFVAL -#undef DDR_PHY_DX5GTR0_RESERVED_15_13_SHIFT -#undef DDR_PHY_DX5GTR0_RESERVED_15_13_MASK -#define DDR_PHY_DX5GTR0_RESERVED_15_13_DEFVAL 0x00020000 -#define DDR_PHY_DX5GTR0_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_DX5GTR0_RESERVED_15_13_MASK 0x0000E000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX5GTR0_RESERVED_12_8_DEFVAL -#undef DDR_PHY_DX5GTR0_RESERVED_12_8_SHIFT -#undef DDR_PHY_DX5GTR0_RESERVED_12_8_MASK -#define DDR_PHY_DX5GTR0_RESERVED_12_8_DEFVAL 0x00020000 -#define DDR_PHY_DX5GTR0_RESERVED_12_8_SHIFT 8 -#define DDR_PHY_DX5GTR0_RESERVED_12_8_MASK 0x00001F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX5GTR0_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DX5GTR0_RESERVED_7_5_SHIFT -#undef DDR_PHY_DX5GTR0_RESERVED_7_5_MASK -#define DDR_PHY_DX5GTR0_RESERVED_7_5_DEFVAL 0x00020000 -#define DDR_PHY_DX5GTR0_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DX5GTR0_RESERVED_7_5_MASK 0x000000E0U - -/*DQS Gating System Latency*/ -#undef DDR_PHY_DX5GTR0_DGSL_DEFVAL -#undef DDR_PHY_DX5GTR0_DGSL_SHIFT -#undef DDR_PHY_DX5GTR0_DGSL_MASK -#define DDR_PHY_DX5GTR0_DGSL_DEFVAL 0x00020000 -#define DDR_PHY_DX5GTR0_DGSL_SHIFT 0 -#define DDR_PHY_DX5GTR0_DGSL_MASK 0x0000001FU - -/*Calibration Bypass*/ -#undef DDR_PHY_DX6GCR0_CALBYP_DEFVAL -#undef DDR_PHY_DX6GCR0_CALBYP_SHIFT -#undef DDR_PHY_DX6GCR0_CALBYP_MASK -#define DDR_PHY_DX6GCR0_CALBYP_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_CALBYP_SHIFT 31 -#define DDR_PHY_DX6GCR0_CALBYP_MASK 0x80000000U - -/*Master Delay Line Enable*/ -#undef DDR_PHY_DX6GCR0_MDLEN_DEFVAL -#undef DDR_PHY_DX6GCR0_MDLEN_SHIFT -#undef DDR_PHY_DX6GCR0_MDLEN_MASK -#define DDR_PHY_DX6GCR0_MDLEN_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_MDLEN_SHIFT 30 -#define DDR_PHY_DX6GCR0_MDLEN_MASK 0x40000000U - -/*Configurable ODT(TE) Phase Shift*/ -#undef DDR_PHY_DX6GCR0_CODTSHFT_DEFVAL -#undef DDR_PHY_DX6GCR0_CODTSHFT_SHIFT -#undef DDR_PHY_DX6GCR0_CODTSHFT_MASK -#define DDR_PHY_DX6GCR0_CODTSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_CODTSHFT_SHIFT 28 -#define DDR_PHY_DX6GCR0_CODTSHFT_MASK 0x30000000U - -/*DQS Duty Cycle Correction*/ -#undef DDR_PHY_DX6GCR0_DQSDCC_DEFVAL -#undef DDR_PHY_DX6GCR0_DQSDCC_SHIFT -#undef DDR_PHY_DX6GCR0_DQSDCC_MASK -#define DDR_PHY_DX6GCR0_DQSDCC_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_DQSDCC_SHIFT 24 -#define DDR_PHY_DX6GCR0_DQSDCC_MASK 0x0F000000U - -/*Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY*/ -#undef DDR_PHY_DX6GCR0_RDDLY_DEFVAL -#undef DDR_PHY_DX6GCR0_RDDLY_SHIFT -#undef DDR_PHY_DX6GCR0_RDDLY_MASK -#define DDR_PHY_DX6GCR0_RDDLY_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_RDDLY_SHIFT 20 -#define DDR_PHY_DX6GCR0_RDDLY_MASK 0x00F00000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX6GCR0_RESERVED_19_14_DEFVAL -#undef DDR_PHY_DX6GCR0_RESERVED_19_14_SHIFT -#undef DDR_PHY_DX6GCR0_RESERVED_19_14_MASK -#define DDR_PHY_DX6GCR0_RESERVED_19_14_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_RESERVED_19_14_SHIFT 14 -#define DDR_PHY_DX6GCR0_RESERVED_19_14_MASK 0x000FC000U - -/*DQSNSE Power Down Receiver*/ -#undef DDR_PHY_DX6GCR0_DQSNSEPDR_DEFVAL -#undef DDR_PHY_DX6GCR0_DQSNSEPDR_SHIFT -#undef DDR_PHY_DX6GCR0_DQSNSEPDR_MASK -#define DDR_PHY_DX6GCR0_DQSNSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_DQSNSEPDR_SHIFT 13 -#define DDR_PHY_DX6GCR0_DQSNSEPDR_MASK 0x00002000U - -/*DQSSE Power Down Receiver*/ -#undef DDR_PHY_DX6GCR0_DQSSEPDR_DEFVAL -#undef DDR_PHY_DX6GCR0_DQSSEPDR_SHIFT -#undef DDR_PHY_DX6GCR0_DQSSEPDR_MASK -#define DDR_PHY_DX6GCR0_DQSSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_DQSSEPDR_SHIFT 12 -#define DDR_PHY_DX6GCR0_DQSSEPDR_MASK 0x00001000U - -/*RTT On Additive Latency*/ -#undef DDR_PHY_DX6GCR0_RTTOAL_DEFVAL -#undef DDR_PHY_DX6GCR0_RTTOAL_SHIFT -#undef DDR_PHY_DX6GCR0_RTTOAL_MASK -#define DDR_PHY_DX6GCR0_RTTOAL_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_RTTOAL_SHIFT 11 -#define DDR_PHY_DX6GCR0_RTTOAL_MASK 0x00000800U - -/*RTT Output Hold*/ -#undef DDR_PHY_DX6GCR0_RTTOH_DEFVAL -#undef DDR_PHY_DX6GCR0_RTTOH_SHIFT -#undef DDR_PHY_DX6GCR0_RTTOH_MASK -#define DDR_PHY_DX6GCR0_RTTOH_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_RTTOH_SHIFT 9 -#define DDR_PHY_DX6GCR0_RTTOH_MASK 0x00000600U - -/*Configurable PDR Phase Shift*/ -#undef DDR_PHY_DX6GCR0_CPDRSHFT_DEFVAL -#undef DDR_PHY_DX6GCR0_CPDRSHFT_SHIFT -#undef DDR_PHY_DX6GCR0_CPDRSHFT_MASK -#define DDR_PHY_DX6GCR0_CPDRSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_CPDRSHFT_SHIFT 7 -#define DDR_PHY_DX6GCR0_CPDRSHFT_MASK 0x00000180U - -/*DQSR Power Down*/ -#undef DDR_PHY_DX6GCR0_DQSRPD_DEFVAL -#undef DDR_PHY_DX6GCR0_DQSRPD_SHIFT -#undef DDR_PHY_DX6GCR0_DQSRPD_MASK -#define DDR_PHY_DX6GCR0_DQSRPD_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_DQSRPD_SHIFT 6 -#define DDR_PHY_DX6GCR0_DQSRPD_MASK 0x00000040U - -/*DQSG Power Down Receiver*/ -#undef DDR_PHY_DX6GCR0_DQSGPDR_DEFVAL -#undef DDR_PHY_DX6GCR0_DQSGPDR_SHIFT -#undef DDR_PHY_DX6GCR0_DQSGPDR_MASK -#define DDR_PHY_DX6GCR0_DQSGPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_DQSGPDR_SHIFT 5 -#define DDR_PHY_DX6GCR0_DQSGPDR_MASK 0x00000020U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX6GCR0_RESERVED_4_DEFVAL -#undef DDR_PHY_DX6GCR0_RESERVED_4_SHIFT -#undef DDR_PHY_DX6GCR0_RESERVED_4_MASK -#define DDR_PHY_DX6GCR0_RESERVED_4_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_RESERVED_4_SHIFT 4 -#define DDR_PHY_DX6GCR0_RESERVED_4_MASK 0x00000010U - -/*DQSG On-Die Termination*/ -#undef DDR_PHY_DX6GCR0_DQSGODT_DEFVAL -#undef DDR_PHY_DX6GCR0_DQSGODT_SHIFT -#undef DDR_PHY_DX6GCR0_DQSGODT_MASK -#define DDR_PHY_DX6GCR0_DQSGODT_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_DQSGODT_SHIFT 3 -#define DDR_PHY_DX6GCR0_DQSGODT_MASK 0x00000008U - -/*DQSG Output Enable*/ -#undef DDR_PHY_DX6GCR0_DQSGOE_DEFVAL -#undef DDR_PHY_DX6GCR0_DQSGOE_SHIFT -#undef DDR_PHY_DX6GCR0_DQSGOE_MASK -#define DDR_PHY_DX6GCR0_DQSGOE_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_DQSGOE_SHIFT 2 -#define DDR_PHY_DX6GCR0_DQSGOE_MASK 0x00000004U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX6GCR0_RESERVED_1_0_DEFVAL -#undef DDR_PHY_DX6GCR0_RESERVED_1_0_SHIFT -#undef DDR_PHY_DX6GCR0_RESERVED_1_0_MASK -#define DDR_PHY_DX6GCR0_RESERVED_1_0_DEFVAL 0x40200204 -#define DDR_PHY_DX6GCR0_RESERVED_1_0_SHIFT 0 -#define DDR_PHY_DX6GCR0_RESERVED_1_0_MASK 0x00000003U - -/*Enables the PDR mode for DQ[7:0]*/ -#undef DDR_PHY_DX6GCR1_DXPDRMODE_DEFVAL -#undef DDR_PHY_DX6GCR1_DXPDRMODE_SHIFT -#undef DDR_PHY_DX6GCR1_DXPDRMODE_MASK -#define DDR_PHY_DX6GCR1_DXPDRMODE_DEFVAL 0x00007FFF -#define DDR_PHY_DX6GCR1_DXPDRMODE_SHIFT 16 -#define DDR_PHY_DX6GCR1_DXPDRMODE_MASK 0xFFFF0000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_DX6GCR1_RESERVED_15_DEFVAL -#undef DDR_PHY_DX6GCR1_RESERVED_15_SHIFT -#undef DDR_PHY_DX6GCR1_RESERVED_15_MASK -#define DDR_PHY_DX6GCR1_RESERVED_15_DEFVAL 0x00007FFF -#define DDR_PHY_DX6GCR1_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX6GCR1_RESERVED_15_MASK 0x00008000U - -/*Select the delayed or non-delayed read data strobe #*/ -#undef DDR_PHY_DX6GCR1_QSNSEL_DEFVAL -#undef DDR_PHY_DX6GCR1_QSNSEL_SHIFT -#undef DDR_PHY_DX6GCR1_QSNSEL_MASK -#define DDR_PHY_DX6GCR1_QSNSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX6GCR1_QSNSEL_SHIFT 14 -#define DDR_PHY_DX6GCR1_QSNSEL_MASK 0x00004000U - -/*Select the delayed or non-delayed read data strobe*/ -#undef DDR_PHY_DX6GCR1_QSSEL_DEFVAL -#undef DDR_PHY_DX6GCR1_QSSEL_SHIFT -#undef DDR_PHY_DX6GCR1_QSSEL_MASK -#define DDR_PHY_DX6GCR1_QSSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX6GCR1_QSSEL_SHIFT 13 -#define DDR_PHY_DX6GCR1_QSSEL_MASK 0x00002000U - -/*Enables Read Data Strobe in a byte lane*/ -#undef DDR_PHY_DX6GCR1_OEEN_DEFVAL -#undef DDR_PHY_DX6GCR1_OEEN_SHIFT -#undef DDR_PHY_DX6GCR1_OEEN_MASK -#define DDR_PHY_DX6GCR1_OEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX6GCR1_OEEN_SHIFT 12 -#define DDR_PHY_DX6GCR1_OEEN_MASK 0x00001000U - -/*Enables PDR in a byte lane*/ -#undef DDR_PHY_DX6GCR1_PDREN_DEFVAL -#undef DDR_PHY_DX6GCR1_PDREN_SHIFT -#undef DDR_PHY_DX6GCR1_PDREN_MASK -#define DDR_PHY_DX6GCR1_PDREN_DEFVAL 0x00007FFF -#define DDR_PHY_DX6GCR1_PDREN_SHIFT 11 -#define DDR_PHY_DX6GCR1_PDREN_MASK 0x00000800U - -/*Enables ODT/TE in a byte lane*/ -#undef DDR_PHY_DX6GCR1_TEEN_DEFVAL -#undef DDR_PHY_DX6GCR1_TEEN_SHIFT -#undef DDR_PHY_DX6GCR1_TEEN_MASK -#define DDR_PHY_DX6GCR1_TEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX6GCR1_TEEN_SHIFT 10 -#define DDR_PHY_DX6GCR1_TEEN_MASK 0x00000400U - -/*Enables Write Data strobe in a byte lane*/ -#undef DDR_PHY_DX6GCR1_DSEN_DEFVAL -#undef DDR_PHY_DX6GCR1_DSEN_SHIFT -#undef DDR_PHY_DX6GCR1_DSEN_MASK -#define DDR_PHY_DX6GCR1_DSEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX6GCR1_DSEN_SHIFT 9 -#define DDR_PHY_DX6GCR1_DSEN_MASK 0x00000200U - -/*Enables DM pin in a byte lane*/ -#undef DDR_PHY_DX6GCR1_DMEN_DEFVAL -#undef DDR_PHY_DX6GCR1_DMEN_SHIFT -#undef DDR_PHY_DX6GCR1_DMEN_MASK -#define DDR_PHY_DX6GCR1_DMEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX6GCR1_DMEN_SHIFT 8 -#define DDR_PHY_DX6GCR1_DMEN_MASK 0x00000100U - -/*Enables DQ corresponding to each bit in a byte*/ -#undef DDR_PHY_DX6GCR1_DQEN_DEFVAL -#undef DDR_PHY_DX6GCR1_DQEN_SHIFT -#undef DDR_PHY_DX6GCR1_DQEN_MASK -#define DDR_PHY_DX6GCR1_DQEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX6GCR1_DQEN_SHIFT 0 -#define DDR_PHY_DX6GCR1_DQEN_MASK 0x000000FFU - -/*Byte lane VREF IOM (Used only by D4MU IOs)*/ -#undef DDR_PHY_DX6GCR4_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DX6GCR4_RESERVED_31_29_SHIFT -#undef DDR_PHY_DX6GCR4_RESERVED_31_29_MASK -#define DDR_PHY_DX6GCR4_RESERVED_31_29_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DX6GCR4_RESERVED_31_29_MASK 0xE0000000U - -/*Byte Lane VREF Pad Enable*/ -#undef DDR_PHY_DX6GCR4_DXREFPEN_DEFVAL -#undef DDR_PHY_DX6GCR4_DXREFPEN_SHIFT -#undef DDR_PHY_DX6GCR4_DXREFPEN_MASK -#define DDR_PHY_DX6GCR4_DXREFPEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_DXREFPEN_SHIFT 28 -#define DDR_PHY_DX6GCR4_DXREFPEN_MASK 0x10000000U - -/*Byte Lane Internal VREF Enable*/ -#undef DDR_PHY_DX6GCR4_DXREFEEN_DEFVAL -#undef DDR_PHY_DX6GCR4_DXREFEEN_SHIFT -#undef DDR_PHY_DX6GCR4_DXREFEEN_MASK -#define DDR_PHY_DX6GCR4_DXREFEEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_DXREFEEN_SHIFT 26 -#define DDR_PHY_DX6GCR4_DXREFEEN_MASK 0x0C000000U - -/*Byte Lane Single-End VREF Enable*/ -#undef DDR_PHY_DX6GCR4_DXREFSEN_DEFVAL -#undef DDR_PHY_DX6GCR4_DXREFSEN_SHIFT -#undef DDR_PHY_DX6GCR4_DXREFSEN_MASK -#define DDR_PHY_DX6GCR4_DXREFSEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_DXREFSEN_SHIFT 25 -#define DDR_PHY_DX6GCR4_DXREFSEN_MASK 0x02000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX6GCR4_RESERVED_24_DEFVAL -#undef DDR_PHY_DX6GCR4_RESERVED_24_SHIFT -#undef DDR_PHY_DX6GCR4_RESERVED_24_MASK -#define DDR_PHY_DX6GCR4_RESERVED_24_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_RESERVED_24_SHIFT 24 -#define DDR_PHY_DX6GCR4_RESERVED_24_MASK 0x01000000U - -/*External VREF generator REFSEL range select*/ -#undef DDR_PHY_DX6GCR4_DXREFESELRANGE_DEFVAL -#undef DDR_PHY_DX6GCR4_DXREFESELRANGE_SHIFT -#undef DDR_PHY_DX6GCR4_DXREFESELRANGE_MASK -#define DDR_PHY_DX6GCR4_DXREFESELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_DXREFESELRANGE_SHIFT 23 -#define DDR_PHY_DX6GCR4_DXREFESELRANGE_MASK 0x00800000U - -/*Byte Lane External VREF Select*/ -#undef DDR_PHY_DX6GCR4_DXREFESEL_DEFVAL -#undef DDR_PHY_DX6GCR4_DXREFESEL_SHIFT -#undef DDR_PHY_DX6GCR4_DXREFESEL_MASK -#define DDR_PHY_DX6GCR4_DXREFESEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_DXREFESEL_SHIFT 16 -#define DDR_PHY_DX6GCR4_DXREFESEL_MASK 0x007F0000U - -/*Single ended VREF generator REFSEL range select*/ -#undef DDR_PHY_DX6GCR4_DXREFSSELRANGE_DEFVAL -#undef DDR_PHY_DX6GCR4_DXREFSSELRANGE_SHIFT -#undef DDR_PHY_DX6GCR4_DXREFSSELRANGE_MASK -#define DDR_PHY_DX6GCR4_DXREFSSELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_DXREFSSELRANGE_SHIFT 15 -#define DDR_PHY_DX6GCR4_DXREFSSELRANGE_MASK 0x00008000U - -/*Byte Lane Single-End VREF Select*/ -#undef DDR_PHY_DX6GCR4_DXREFSSEL_DEFVAL -#undef DDR_PHY_DX6GCR4_DXREFSSEL_SHIFT -#undef DDR_PHY_DX6GCR4_DXREFSSEL_MASK -#define DDR_PHY_DX6GCR4_DXREFSSEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_DXREFSSEL_SHIFT 8 -#define DDR_PHY_DX6GCR4_DXREFSSEL_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX6GCR4_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX6GCR4_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX6GCR4_RESERVED_7_6_MASK -#define DDR_PHY_DX6GCR4_RESERVED_7_6_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX6GCR4_RESERVED_7_6_MASK 0x000000C0U - -/*VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX6GCR4_DXREFIEN_DEFVAL -#undef DDR_PHY_DX6GCR4_DXREFIEN_SHIFT -#undef DDR_PHY_DX6GCR4_DXREFIEN_MASK -#define DDR_PHY_DX6GCR4_DXREFIEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_DXREFIEN_SHIFT 2 -#define DDR_PHY_DX6GCR4_DXREFIEN_MASK 0x0000003CU - -/*VRMON control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX6GCR4_DXREFIMON_DEFVAL -#undef DDR_PHY_DX6GCR4_DXREFIMON_SHIFT -#undef DDR_PHY_DX6GCR4_DXREFIMON_MASK -#define DDR_PHY_DX6GCR4_DXREFIMON_DEFVAL 0x0E00003C -#define DDR_PHY_DX6GCR4_DXREFIMON_SHIFT 0 -#define DDR_PHY_DX6GCR4_DXREFIMON_MASK 0x00000003U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX6GCR5_RESERVED_31_DEFVAL -#undef DDR_PHY_DX6GCR5_RESERVED_31_SHIFT -#undef DDR_PHY_DX6GCR5_RESERVED_31_MASK -#define DDR_PHY_DX6GCR5_RESERVED_31_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR5_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX6GCR5_RESERVED_31_MASK 0x80000000U - -/*Byte Lane internal VREF Select for Rank 3*/ -#undef DDR_PHY_DX6GCR5_DXREFISELR3_DEFVAL -#undef DDR_PHY_DX6GCR5_DXREFISELR3_SHIFT -#undef DDR_PHY_DX6GCR5_DXREFISELR3_MASK -#define DDR_PHY_DX6GCR5_DXREFISELR3_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR5_DXREFISELR3_SHIFT 24 -#define DDR_PHY_DX6GCR5_DXREFISELR3_MASK 0x7F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX6GCR5_RESERVED_23_DEFVAL -#undef DDR_PHY_DX6GCR5_RESERVED_23_SHIFT -#undef DDR_PHY_DX6GCR5_RESERVED_23_MASK -#define DDR_PHY_DX6GCR5_RESERVED_23_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR5_RESERVED_23_SHIFT 23 -#define DDR_PHY_DX6GCR5_RESERVED_23_MASK 0x00800000U - -/*Byte Lane internal VREF Select for Rank 2*/ -#undef DDR_PHY_DX6GCR5_DXREFISELR2_DEFVAL -#undef DDR_PHY_DX6GCR5_DXREFISELR2_SHIFT -#undef DDR_PHY_DX6GCR5_DXREFISELR2_MASK -#define DDR_PHY_DX6GCR5_DXREFISELR2_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR5_DXREFISELR2_SHIFT 16 -#define DDR_PHY_DX6GCR5_DXREFISELR2_MASK 0x007F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX6GCR5_RESERVED_15_DEFVAL -#undef DDR_PHY_DX6GCR5_RESERVED_15_SHIFT -#undef DDR_PHY_DX6GCR5_RESERVED_15_MASK -#define DDR_PHY_DX6GCR5_RESERVED_15_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR5_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX6GCR5_RESERVED_15_MASK 0x00008000U - -/*Byte Lane internal VREF Select for Rank 1*/ -#undef DDR_PHY_DX6GCR5_DXREFISELR1_DEFVAL -#undef DDR_PHY_DX6GCR5_DXREFISELR1_SHIFT -#undef DDR_PHY_DX6GCR5_DXREFISELR1_MASK -#define DDR_PHY_DX6GCR5_DXREFISELR1_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR5_DXREFISELR1_SHIFT 8 -#define DDR_PHY_DX6GCR5_DXREFISELR1_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX6GCR5_RESERVED_7_DEFVAL -#undef DDR_PHY_DX6GCR5_RESERVED_7_SHIFT -#undef DDR_PHY_DX6GCR5_RESERVED_7_MASK -#define DDR_PHY_DX6GCR5_RESERVED_7_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR5_RESERVED_7_SHIFT 7 -#define DDR_PHY_DX6GCR5_RESERVED_7_MASK 0x00000080U - -/*Byte Lane internal VREF Select for Rank 0*/ -#undef DDR_PHY_DX6GCR5_DXREFISELR0_DEFVAL -#undef DDR_PHY_DX6GCR5_DXREFISELR0_SHIFT -#undef DDR_PHY_DX6GCR5_DXREFISELR0_MASK -#define DDR_PHY_DX6GCR5_DXREFISELR0_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR5_DXREFISELR0_SHIFT 0 -#define DDR_PHY_DX6GCR5_DXREFISELR0_MASK 0x0000007FU - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX6GCR6_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX6GCR6_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX6GCR6_RESERVED_31_30_MASK -#define DDR_PHY_DX6GCR6_RESERVED_31_30_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR6_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX6GCR6_RESERVED_31_30_MASK 0xC0000000U - -/*DRAM DQ VREF Select for Rank3*/ -#undef DDR_PHY_DX6GCR6_DXDQVREFR3_DEFVAL -#undef DDR_PHY_DX6GCR6_DXDQVREFR3_SHIFT -#undef DDR_PHY_DX6GCR6_DXDQVREFR3_MASK -#define DDR_PHY_DX6GCR6_DXDQVREFR3_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR6_DXDQVREFR3_SHIFT 24 -#define DDR_PHY_DX6GCR6_DXDQVREFR3_MASK 0x3F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX6GCR6_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX6GCR6_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX6GCR6_RESERVED_23_22_MASK -#define DDR_PHY_DX6GCR6_RESERVED_23_22_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR6_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX6GCR6_RESERVED_23_22_MASK 0x00C00000U - -/*DRAM DQ VREF Select for Rank2*/ -#undef DDR_PHY_DX6GCR6_DXDQVREFR2_DEFVAL -#undef DDR_PHY_DX6GCR6_DXDQVREFR2_SHIFT -#undef DDR_PHY_DX6GCR6_DXDQVREFR2_MASK -#define DDR_PHY_DX6GCR6_DXDQVREFR2_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR6_DXDQVREFR2_SHIFT 16 -#define DDR_PHY_DX6GCR6_DXDQVREFR2_MASK 0x003F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX6GCR6_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DX6GCR6_RESERVED_15_14_SHIFT -#undef DDR_PHY_DX6GCR6_RESERVED_15_14_MASK -#define DDR_PHY_DX6GCR6_RESERVED_15_14_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR6_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DX6GCR6_RESERVED_15_14_MASK 0x0000C000U - -/*DRAM DQ VREF Select for Rank1*/ -#undef DDR_PHY_DX6GCR6_DXDQVREFR1_DEFVAL -#undef DDR_PHY_DX6GCR6_DXDQVREFR1_SHIFT -#undef DDR_PHY_DX6GCR6_DXDQVREFR1_MASK -#define DDR_PHY_DX6GCR6_DXDQVREFR1_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR6_DXDQVREFR1_SHIFT 8 -#define DDR_PHY_DX6GCR6_DXDQVREFR1_MASK 0x00003F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX6GCR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX6GCR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX6GCR6_RESERVED_7_6_MASK -#define DDR_PHY_DX6GCR6_RESERVED_7_6_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX6GCR6_RESERVED_7_6_MASK 0x000000C0U - -/*DRAM DQ VREF Select for Rank0*/ -#undef DDR_PHY_DX6GCR6_DXDQVREFR0_DEFVAL -#undef DDR_PHY_DX6GCR6_DXDQVREFR0_SHIFT -#undef DDR_PHY_DX6GCR6_DXDQVREFR0_MASK -#define DDR_PHY_DX6GCR6_DXDQVREFR0_DEFVAL 0x09090909 -#define DDR_PHY_DX6GCR6_DXDQVREFR0_SHIFT 0 -#define DDR_PHY_DX6GCR6_DXDQVREFR0_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX6LCDLR2_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX6LCDLR2_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX6LCDLR2_RESERVED_31_25_MASK -#define DDR_PHY_DX6LCDLR2_RESERVED_31_25_DEFVAL 0x00000000 -#define DDR_PHY_DX6LCDLR2_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX6LCDLR2_RESERVED_31_25_MASK 0xFE000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX6LCDLR2_RESERVED_24_16_DEFVAL -#undef DDR_PHY_DX6LCDLR2_RESERVED_24_16_SHIFT -#undef DDR_PHY_DX6LCDLR2_RESERVED_24_16_MASK -#define DDR_PHY_DX6LCDLR2_RESERVED_24_16_DEFVAL 0x00000000 -#define DDR_PHY_DX6LCDLR2_RESERVED_24_16_SHIFT 16 -#define DDR_PHY_DX6LCDLR2_RESERVED_24_16_MASK 0x01FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX6LCDLR2_RESERVED_15_9_DEFVAL -#undef DDR_PHY_DX6LCDLR2_RESERVED_15_9_SHIFT -#undef DDR_PHY_DX6LCDLR2_RESERVED_15_9_MASK -#define DDR_PHY_DX6LCDLR2_RESERVED_15_9_DEFVAL 0x00000000 -#define DDR_PHY_DX6LCDLR2_RESERVED_15_9_SHIFT 9 -#define DDR_PHY_DX6LCDLR2_RESERVED_15_9_MASK 0x0000FE00U - -/*Read DQS Gating Delay*/ -#undef DDR_PHY_DX6LCDLR2_DQSGD_DEFVAL -#undef DDR_PHY_DX6LCDLR2_DQSGD_SHIFT -#undef DDR_PHY_DX6LCDLR2_DQSGD_MASK -#define DDR_PHY_DX6LCDLR2_DQSGD_DEFVAL 0x00000000 -#define DDR_PHY_DX6LCDLR2_DQSGD_SHIFT 0 -#define DDR_PHY_DX6LCDLR2_DQSGD_MASK 0x000001FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX6GTR0_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX6GTR0_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX6GTR0_RESERVED_31_24_MASK -#define DDR_PHY_DX6GTR0_RESERVED_31_24_DEFVAL 0x00020000 -#define DDR_PHY_DX6GTR0_RESERVED_31_24_SHIFT 27 -#define DDR_PHY_DX6GTR0_RESERVED_31_24_MASK 0xF8000000U - -/*DQ Write Path Latency Pipeline*/ -#undef DDR_PHY_DX6GTR0_WDQSL_DEFVAL -#undef DDR_PHY_DX6GTR0_WDQSL_SHIFT -#undef DDR_PHY_DX6GTR0_WDQSL_MASK -#define DDR_PHY_DX6GTR0_WDQSL_DEFVAL 0x00020000 -#define DDR_PHY_DX6GTR0_WDQSL_SHIFT 24 -#define DDR_PHY_DX6GTR0_WDQSL_MASK 0x07000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX6GTR0_RESERVED_23_20_DEFVAL -#undef DDR_PHY_DX6GTR0_RESERVED_23_20_SHIFT -#undef DDR_PHY_DX6GTR0_RESERVED_23_20_MASK -#define DDR_PHY_DX6GTR0_RESERVED_23_20_DEFVAL 0x00020000 -#define DDR_PHY_DX6GTR0_RESERVED_23_20_SHIFT 20 -#define DDR_PHY_DX6GTR0_RESERVED_23_20_MASK 0x00F00000U - -/*Write Leveling System Latency*/ -#undef DDR_PHY_DX6GTR0_WLSL_DEFVAL -#undef DDR_PHY_DX6GTR0_WLSL_SHIFT -#undef DDR_PHY_DX6GTR0_WLSL_MASK -#define DDR_PHY_DX6GTR0_WLSL_DEFVAL 0x00020000 -#define DDR_PHY_DX6GTR0_WLSL_SHIFT 16 -#define DDR_PHY_DX6GTR0_WLSL_MASK 0x000F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX6GTR0_RESERVED_15_13_DEFVAL -#undef DDR_PHY_DX6GTR0_RESERVED_15_13_SHIFT -#undef DDR_PHY_DX6GTR0_RESERVED_15_13_MASK -#define DDR_PHY_DX6GTR0_RESERVED_15_13_DEFVAL 0x00020000 -#define DDR_PHY_DX6GTR0_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_DX6GTR0_RESERVED_15_13_MASK 0x0000E000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX6GTR0_RESERVED_12_8_DEFVAL -#undef DDR_PHY_DX6GTR0_RESERVED_12_8_SHIFT -#undef DDR_PHY_DX6GTR0_RESERVED_12_8_MASK -#define DDR_PHY_DX6GTR0_RESERVED_12_8_DEFVAL 0x00020000 -#define DDR_PHY_DX6GTR0_RESERVED_12_8_SHIFT 8 -#define DDR_PHY_DX6GTR0_RESERVED_12_8_MASK 0x00001F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX6GTR0_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DX6GTR0_RESERVED_7_5_SHIFT -#undef DDR_PHY_DX6GTR0_RESERVED_7_5_MASK -#define DDR_PHY_DX6GTR0_RESERVED_7_5_DEFVAL 0x00020000 -#define DDR_PHY_DX6GTR0_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DX6GTR0_RESERVED_7_5_MASK 0x000000E0U - -/*DQS Gating System Latency*/ -#undef DDR_PHY_DX6GTR0_DGSL_DEFVAL -#undef DDR_PHY_DX6GTR0_DGSL_SHIFT -#undef DDR_PHY_DX6GTR0_DGSL_MASK -#define DDR_PHY_DX6GTR0_DGSL_DEFVAL 0x00020000 -#define DDR_PHY_DX6GTR0_DGSL_SHIFT 0 -#define DDR_PHY_DX6GTR0_DGSL_MASK 0x0000001FU - -/*Calibration Bypass*/ -#undef DDR_PHY_DX7GCR0_CALBYP_DEFVAL -#undef DDR_PHY_DX7GCR0_CALBYP_SHIFT -#undef DDR_PHY_DX7GCR0_CALBYP_MASK -#define DDR_PHY_DX7GCR0_CALBYP_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_CALBYP_SHIFT 31 -#define DDR_PHY_DX7GCR0_CALBYP_MASK 0x80000000U - -/*Master Delay Line Enable*/ -#undef DDR_PHY_DX7GCR0_MDLEN_DEFVAL -#undef DDR_PHY_DX7GCR0_MDLEN_SHIFT -#undef DDR_PHY_DX7GCR0_MDLEN_MASK -#define DDR_PHY_DX7GCR0_MDLEN_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_MDLEN_SHIFT 30 -#define DDR_PHY_DX7GCR0_MDLEN_MASK 0x40000000U - -/*Configurable ODT(TE) Phase Shift*/ -#undef DDR_PHY_DX7GCR0_CODTSHFT_DEFVAL -#undef DDR_PHY_DX7GCR0_CODTSHFT_SHIFT -#undef DDR_PHY_DX7GCR0_CODTSHFT_MASK -#define DDR_PHY_DX7GCR0_CODTSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_CODTSHFT_SHIFT 28 -#define DDR_PHY_DX7GCR0_CODTSHFT_MASK 0x30000000U - -/*DQS Duty Cycle Correction*/ -#undef DDR_PHY_DX7GCR0_DQSDCC_DEFVAL -#undef DDR_PHY_DX7GCR0_DQSDCC_SHIFT -#undef DDR_PHY_DX7GCR0_DQSDCC_MASK -#define DDR_PHY_DX7GCR0_DQSDCC_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_DQSDCC_SHIFT 24 -#define DDR_PHY_DX7GCR0_DQSDCC_MASK 0x0F000000U - -/*Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY*/ -#undef DDR_PHY_DX7GCR0_RDDLY_DEFVAL -#undef DDR_PHY_DX7GCR0_RDDLY_SHIFT -#undef DDR_PHY_DX7GCR0_RDDLY_MASK -#define DDR_PHY_DX7GCR0_RDDLY_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_RDDLY_SHIFT 20 -#define DDR_PHY_DX7GCR0_RDDLY_MASK 0x00F00000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX7GCR0_RESERVED_19_14_DEFVAL -#undef DDR_PHY_DX7GCR0_RESERVED_19_14_SHIFT -#undef DDR_PHY_DX7GCR0_RESERVED_19_14_MASK -#define DDR_PHY_DX7GCR0_RESERVED_19_14_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_RESERVED_19_14_SHIFT 14 -#define DDR_PHY_DX7GCR0_RESERVED_19_14_MASK 0x000FC000U - -/*DQSNSE Power Down Receiver*/ -#undef DDR_PHY_DX7GCR0_DQSNSEPDR_DEFVAL -#undef DDR_PHY_DX7GCR0_DQSNSEPDR_SHIFT -#undef DDR_PHY_DX7GCR0_DQSNSEPDR_MASK -#define DDR_PHY_DX7GCR0_DQSNSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_DQSNSEPDR_SHIFT 13 -#define DDR_PHY_DX7GCR0_DQSNSEPDR_MASK 0x00002000U - -/*DQSSE Power Down Receiver*/ -#undef DDR_PHY_DX7GCR0_DQSSEPDR_DEFVAL -#undef DDR_PHY_DX7GCR0_DQSSEPDR_SHIFT -#undef DDR_PHY_DX7GCR0_DQSSEPDR_MASK -#define DDR_PHY_DX7GCR0_DQSSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_DQSSEPDR_SHIFT 12 -#define DDR_PHY_DX7GCR0_DQSSEPDR_MASK 0x00001000U - -/*RTT On Additive Latency*/ -#undef DDR_PHY_DX7GCR0_RTTOAL_DEFVAL -#undef DDR_PHY_DX7GCR0_RTTOAL_SHIFT -#undef DDR_PHY_DX7GCR0_RTTOAL_MASK -#define DDR_PHY_DX7GCR0_RTTOAL_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_RTTOAL_SHIFT 11 -#define DDR_PHY_DX7GCR0_RTTOAL_MASK 0x00000800U - -/*RTT Output Hold*/ -#undef DDR_PHY_DX7GCR0_RTTOH_DEFVAL -#undef DDR_PHY_DX7GCR0_RTTOH_SHIFT -#undef DDR_PHY_DX7GCR0_RTTOH_MASK -#define DDR_PHY_DX7GCR0_RTTOH_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_RTTOH_SHIFT 9 -#define DDR_PHY_DX7GCR0_RTTOH_MASK 0x00000600U - -/*Configurable PDR Phase Shift*/ -#undef DDR_PHY_DX7GCR0_CPDRSHFT_DEFVAL -#undef DDR_PHY_DX7GCR0_CPDRSHFT_SHIFT -#undef DDR_PHY_DX7GCR0_CPDRSHFT_MASK -#define DDR_PHY_DX7GCR0_CPDRSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_CPDRSHFT_SHIFT 7 -#define DDR_PHY_DX7GCR0_CPDRSHFT_MASK 0x00000180U - -/*DQSR Power Down*/ -#undef DDR_PHY_DX7GCR0_DQSRPD_DEFVAL -#undef DDR_PHY_DX7GCR0_DQSRPD_SHIFT -#undef DDR_PHY_DX7GCR0_DQSRPD_MASK -#define DDR_PHY_DX7GCR0_DQSRPD_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_DQSRPD_SHIFT 6 -#define DDR_PHY_DX7GCR0_DQSRPD_MASK 0x00000040U - -/*DQSG Power Down Receiver*/ -#undef DDR_PHY_DX7GCR0_DQSGPDR_DEFVAL -#undef DDR_PHY_DX7GCR0_DQSGPDR_SHIFT -#undef DDR_PHY_DX7GCR0_DQSGPDR_MASK -#define DDR_PHY_DX7GCR0_DQSGPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_DQSGPDR_SHIFT 5 -#define DDR_PHY_DX7GCR0_DQSGPDR_MASK 0x00000020U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX7GCR0_RESERVED_4_DEFVAL -#undef DDR_PHY_DX7GCR0_RESERVED_4_SHIFT -#undef DDR_PHY_DX7GCR0_RESERVED_4_MASK -#define DDR_PHY_DX7GCR0_RESERVED_4_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_RESERVED_4_SHIFT 4 -#define DDR_PHY_DX7GCR0_RESERVED_4_MASK 0x00000010U - -/*DQSG On-Die Termination*/ -#undef DDR_PHY_DX7GCR0_DQSGODT_DEFVAL -#undef DDR_PHY_DX7GCR0_DQSGODT_SHIFT -#undef DDR_PHY_DX7GCR0_DQSGODT_MASK -#define DDR_PHY_DX7GCR0_DQSGODT_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_DQSGODT_SHIFT 3 -#define DDR_PHY_DX7GCR0_DQSGODT_MASK 0x00000008U - -/*DQSG Output Enable*/ -#undef DDR_PHY_DX7GCR0_DQSGOE_DEFVAL -#undef DDR_PHY_DX7GCR0_DQSGOE_SHIFT -#undef DDR_PHY_DX7GCR0_DQSGOE_MASK -#define DDR_PHY_DX7GCR0_DQSGOE_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_DQSGOE_SHIFT 2 -#define DDR_PHY_DX7GCR0_DQSGOE_MASK 0x00000004U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX7GCR0_RESERVED_1_0_DEFVAL -#undef DDR_PHY_DX7GCR0_RESERVED_1_0_SHIFT -#undef DDR_PHY_DX7GCR0_RESERVED_1_0_MASK -#define DDR_PHY_DX7GCR0_RESERVED_1_0_DEFVAL 0x40200204 -#define DDR_PHY_DX7GCR0_RESERVED_1_0_SHIFT 0 -#define DDR_PHY_DX7GCR0_RESERVED_1_0_MASK 0x00000003U - -/*Enables the PDR mode for DQ[7:0]*/ -#undef DDR_PHY_DX7GCR1_DXPDRMODE_DEFVAL -#undef DDR_PHY_DX7GCR1_DXPDRMODE_SHIFT -#undef DDR_PHY_DX7GCR1_DXPDRMODE_MASK -#define DDR_PHY_DX7GCR1_DXPDRMODE_DEFVAL 0x00007FFF -#define DDR_PHY_DX7GCR1_DXPDRMODE_SHIFT 16 -#define DDR_PHY_DX7GCR1_DXPDRMODE_MASK 0xFFFF0000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_DX7GCR1_RESERVED_15_DEFVAL -#undef DDR_PHY_DX7GCR1_RESERVED_15_SHIFT -#undef DDR_PHY_DX7GCR1_RESERVED_15_MASK -#define DDR_PHY_DX7GCR1_RESERVED_15_DEFVAL 0x00007FFF -#define DDR_PHY_DX7GCR1_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX7GCR1_RESERVED_15_MASK 0x00008000U - -/*Select the delayed or non-delayed read data strobe #*/ -#undef DDR_PHY_DX7GCR1_QSNSEL_DEFVAL -#undef DDR_PHY_DX7GCR1_QSNSEL_SHIFT -#undef DDR_PHY_DX7GCR1_QSNSEL_MASK -#define DDR_PHY_DX7GCR1_QSNSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX7GCR1_QSNSEL_SHIFT 14 -#define DDR_PHY_DX7GCR1_QSNSEL_MASK 0x00004000U - -/*Select the delayed or non-delayed read data strobe*/ -#undef DDR_PHY_DX7GCR1_QSSEL_DEFVAL -#undef DDR_PHY_DX7GCR1_QSSEL_SHIFT -#undef DDR_PHY_DX7GCR1_QSSEL_MASK -#define DDR_PHY_DX7GCR1_QSSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX7GCR1_QSSEL_SHIFT 13 -#define DDR_PHY_DX7GCR1_QSSEL_MASK 0x00002000U - -/*Enables Read Data Strobe in a byte lane*/ -#undef DDR_PHY_DX7GCR1_OEEN_DEFVAL -#undef DDR_PHY_DX7GCR1_OEEN_SHIFT -#undef DDR_PHY_DX7GCR1_OEEN_MASK -#define DDR_PHY_DX7GCR1_OEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX7GCR1_OEEN_SHIFT 12 -#define DDR_PHY_DX7GCR1_OEEN_MASK 0x00001000U - -/*Enables PDR in a byte lane*/ -#undef DDR_PHY_DX7GCR1_PDREN_DEFVAL -#undef DDR_PHY_DX7GCR1_PDREN_SHIFT -#undef DDR_PHY_DX7GCR1_PDREN_MASK -#define DDR_PHY_DX7GCR1_PDREN_DEFVAL 0x00007FFF -#define DDR_PHY_DX7GCR1_PDREN_SHIFT 11 -#define DDR_PHY_DX7GCR1_PDREN_MASK 0x00000800U - -/*Enables ODT/TE in a byte lane*/ -#undef DDR_PHY_DX7GCR1_TEEN_DEFVAL -#undef DDR_PHY_DX7GCR1_TEEN_SHIFT -#undef DDR_PHY_DX7GCR1_TEEN_MASK -#define DDR_PHY_DX7GCR1_TEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX7GCR1_TEEN_SHIFT 10 -#define DDR_PHY_DX7GCR1_TEEN_MASK 0x00000400U - -/*Enables Write Data strobe in a byte lane*/ -#undef DDR_PHY_DX7GCR1_DSEN_DEFVAL -#undef DDR_PHY_DX7GCR1_DSEN_SHIFT -#undef DDR_PHY_DX7GCR1_DSEN_MASK -#define DDR_PHY_DX7GCR1_DSEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX7GCR1_DSEN_SHIFT 9 -#define DDR_PHY_DX7GCR1_DSEN_MASK 0x00000200U - -/*Enables DM pin in a byte lane*/ -#undef DDR_PHY_DX7GCR1_DMEN_DEFVAL -#undef DDR_PHY_DX7GCR1_DMEN_SHIFT -#undef DDR_PHY_DX7GCR1_DMEN_MASK -#define DDR_PHY_DX7GCR1_DMEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX7GCR1_DMEN_SHIFT 8 -#define DDR_PHY_DX7GCR1_DMEN_MASK 0x00000100U - -/*Enables DQ corresponding to each bit in a byte*/ -#undef DDR_PHY_DX7GCR1_DQEN_DEFVAL -#undef DDR_PHY_DX7GCR1_DQEN_SHIFT -#undef DDR_PHY_DX7GCR1_DQEN_MASK -#define DDR_PHY_DX7GCR1_DQEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX7GCR1_DQEN_SHIFT 0 -#define DDR_PHY_DX7GCR1_DQEN_MASK 0x000000FFU - -/*Byte lane VREF IOM (Used only by D4MU IOs)*/ -#undef DDR_PHY_DX7GCR4_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DX7GCR4_RESERVED_31_29_SHIFT -#undef DDR_PHY_DX7GCR4_RESERVED_31_29_MASK -#define DDR_PHY_DX7GCR4_RESERVED_31_29_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DX7GCR4_RESERVED_31_29_MASK 0xE0000000U - -/*Byte Lane VREF Pad Enable*/ -#undef DDR_PHY_DX7GCR4_DXREFPEN_DEFVAL -#undef DDR_PHY_DX7GCR4_DXREFPEN_SHIFT -#undef DDR_PHY_DX7GCR4_DXREFPEN_MASK -#define DDR_PHY_DX7GCR4_DXREFPEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_DXREFPEN_SHIFT 28 -#define DDR_PHY_DX7GCR4_DXREFPEN_MASK 0x10000000U - -/*Byte Lane Internal VREF Enable*/ -#undef DDR_PHY_DX7GCR4_DXREFEEN_DEFVAL -#undef DDR_PHY_DX7GCR4_DXREFEEN_SHIFT -#undef DDR_PHY_DX7GCR4_DXREFEEN_MASK -#define DDR_PHY_DX7GCR4_DXREFEEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_DXREFEEN_SHIFT 26 -#define DDR_PHY_DX7GCR4_DXREFEEN_MASK 0x0C000000U - -/*Byte Lane Single-End VREF Enable*/ -#undef DDR_PHY_DX7GCR4_DXREFSEN_DEFVAL -#undef DDR_PHY_DX7GCR4_DXREFSEN_SHIFT -#undef DDR_PHY_DX7GCR4_DXREFSEN_MASK -#define DDR_PHY_DX7GCR4_DXREFSEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_DXREFSEN_SHIFT 25 -#define DDR_PHY_DX7GCR4_DXREFSEN_MASK 0x02000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX7GCR4_RESERVED_24_DEFVAL -#undef DDR_PHY_DX7GCR4_RESERVED_24_SHIFT -#undef DDR_PHY_DX7GCR4_RESERVED_24_MASK -#define DDR_PHY_DX7GCR4_RESERVED_24_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_RESERVED_24_SHIFT 24 -#define DDR_PHY_DX7GCR4_RESERVED_24_MASK 0x01000000U - -/*External VREF generator REFSEL range select*/ -#undef DDR_PHY_DX7GCR4_DXREFESELRANGE_DEFVAL -#undef DDR_PHY_DX7GCR4_DXREFESELRANGE_SHIFT -#undef DDR_PHY_DX7GCR4_DXREFESELRANGE_MASK -#define DDR_PHY_DX7GCR4_DXREFESELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_DXREFESELRANGE_SHIFT 23 -#define DDR_PHY_DX7GCR4_DXREFESELRANGE_MASK 0x00800000U - -/*Byte Lane External VREF Select*/ -#undef DDR_PHY_DX7GCR4_DXREFESEL_DEFVAL -#undef DDR_PHY_DX7GCR4_DXREFESEL_SHIFT -#undef DDR_PHY_DX7GCR4_DXREFESEL_MASK -#define DDR_PHY_DX7GCR4_DXREFESEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_DXREFESEL_SHIFT 16 -#define DDR_PHY_DX7GCR4_DXREFESEL_MASK 0x007F0000U - -/*Single ended VREF generator REFSEL range select*/ -#undef DDR_PHY_DX7GCR4_DXREFSSELRANGE_DEFVAL -#undef DDR_PHY_DX7GCR4_DXREFSSELRANGE_SHIFT -#undef DDR_PHY_DX7GCR4_DXREFSSELRANGE_MASK -#define DDR_PHY_DX7GCR4_DXREFSSELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_DXREFSSELRANGE_SHIFT 15 -#define DDR_PHY_DX7GCR4_DXREFSSELRANGE_MASK 0x00008000U - -/*Byte Lane Single-End VREF Select*/ -#undef DDR_PHY_DX7GCR4_DXREFSSEL_DEFVAL -#undef DDR_PHY_DX7GCR4_DXREFSSEL_SHIFT -#undef DDR_PHY_DX7GCR4_DXREFSSEL_MASK -#define DDR_PHY_DX7GCR4_DXREFSSEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_DXREFSSEL_SHIFT 8 -#define DDR_PHY_DX7GCR4_DXREFSSEL_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX7GCR4_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX7GCR4_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX7GCR4_RESERVED_7_6_MASK -#define DDR_PHY_DX7GCR4_RESERVED_7_6_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX7GCR4_RESERVED_7_6_MASK 0x000000C0U - -/*VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX7GCR4_DXREFIEN_DEFVAL -#undef DDR_PHY_DX7GCR4_DXREFIEN_SHIFT -#undef DDR_PHY_DX7GCR4_DXREFIEN_MASK -#define DDR_PHY_DX7GCR4_DXREFIEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_DXREFIEN_SHIFT 2 -#define DDR_PHY_DX7GCR4_DXREFIEN_MASK 0x0000003CU - -/*VRMON control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX7GCR4_DXREFIMON_DEFVAL -#undef DDR_PHY_DX7GCR4_DXREFIMON_SHIFT -#undef DDR_PHY_DX7GCR4_DXREFIMON_MASK -#define DDR_PHY_DX7GCR4_DXREFIMON_DEFVAL 0x0E00003C -#define DDR_PHY_DX7GCR4_DXREFIMON_SHIFT 0 -#define DDR_PHY_DX7GCR4_DXREFIMON_MASK 0x00000003U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX7GCR5_RESERVED_31_DEFVAL -#undef DDR_PHY_DX7GCR5_RESERVED_31_SHIFT -#undef DDR_PHY_DX7GCR5_RESERVED_31_MASK -#define DDR_PHY_DX7GCR5_RESERVED_31_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR5_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX7GCR5_RESERVED_31_MASK 0x80000000U - -/*Byte Lane internal VREF Select for Rank 3*/ -#undef DDR_PHY_DX7GCR5_DXREFISELR3_DEFVAL -#undef DDR_PHY_DX7GCR5_DXREFISELR3_SHIFT -#undef DDR_PHY_DX7GCR5_DXREFISELR3_MASK -#define DDR_PHY_DX7GCR5_DXREFISELR3_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR5_DXREFISELR3_SHIFT 24 -#define DDR_PHY_DX7GCR5_DXREFISELR3_MASK 0x7F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX7GCR5_RESERVED_23_DEFVAL -#undef DDR_PHY_DX7GCR5_RESERVED_23_SHIFT -#undef DDR_PHY_DX7GCR5_RESERVED_23_MASK -#define DDR_PHY_DX7GCR5_RESERVED_23_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR5_RESERVED_23_SHIFT 23 -#define DDR_PHY_DX7GCR5_RESERVED_23_MASK 0x00800000U - -/*Byte Lane internal VREF Select for Rank 2*/ -#undef DDR_PHY_DX7GCR5_DXREFISELR2_DEFVAL -#undef DDR_PHY_DX7GCR5_DXREFISELR2_SHIFT -#undef DDR_PHY_DX7GCR5_DXREFISELR2_MASK -#define DDR_PHY_DX7GCR5_DXREFISELR2_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR5_DXREFISELR2_SHIFT 16 -#define DDR_PHY_DX7GCR5_DXREFISELR2_MASK 0x007F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX7GCR5_RESERVED_15_DEFVAL -#undef DDR_PHY_DX7GCR5_RESERVED_15_SHIFT -#undef DDR_PHY_DX7GCR5_RESERVED_15_MASK -#define DDR_PHY_DX7GCR5_RESERVED_15_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR5_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX7GCR5_RESERVED_15_MASK 0x00008000U - -/*Byte Lane internal VREF Select for Rank 1*/ -#undef DDR_PHY_DX7GCR5_DXREFISELR1_DEFVAL -#undef DDR_PHY_DX7GCR5_DXREFISELR1_SHIFT -#undef DDR_PHY_DX7GCR5_DXREFISELR1_MASK -#define DDR_PHY_DX7GCR5_DXREFISELR1_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR5_DXREFISELR1_SHIFT 8 -#define DDR_PHY_DX7GCR5_DXREFISELR1_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX7GCR5_RESERVED_7_DEFVAL -#undef DDR_PHY_DX7GCR5_RESERVED_7_SHIFT -#undef DDR_PHY_DX7GCR5_RESERVED_7_MASK -#define DDR_PHY_DX7GCR5_RESERVED_7_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR5_RESERVED_7_SHIFT 7 -#define DDR_PHY_DX7GCR5_RESERVED_7_MASK 0x00000080U - -/*Byte Lane internal VREF Select for Rank 0*/ -#undef DDR_PHY_DX7GCR5_DXREFISELR0_DEFVAL -#undef DDR_PHY_DX7GCR5_DXREFISELR0_SHIFT -#undef DDR_PHY_DX7GCR5_DXREFISELR0_MASK -#define DDR_PHY_DX7GCR5_DXREFISELR0_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR5_DXREFISELR0_SHIFT 0 -#define DDR_PHY_DX7GCR5_DXREFISELR0_MASK 0x0000007FU - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX7GCR6_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX7GCR6_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX7GCR6_RESERVED_31_30_MASK -#define DDR_PHY_DX7GCR6_RESERVED_31_30_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR6_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX7GCR6_RESERVED_31_30_MASK 0xC0000000U - -/*DRAM DQ VREF Select for Rank3*/ -#undef DDR_PHY_DX7GCR6_DXDQVREFR3_DEFVAL -#undef DDR_PHY_DX7GCR6_DXDQVREFR3_SHIFT -#undef DDR_PHY_DX7GCR6_DXDQVREFR3_MASK -#define DDR_PHY_DX7GCR6_DXDQVREFR3_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR6_DXDQVREFR3_SHIFT 24 -#define DDR_PHY_DX7GCR6_DXDQVREFR3_MASK 0x3F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX7GCR6_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX7GCR6_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX7GCR6_RESERVED_23_22_MASK -#define DDR_PHY_DX7GCR6_RESERVED_23_22_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR6_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX7GCR6_RESERVED_23_22_MASK 0x00C00000U - -/*DRAM DQ VREF Select for Rank2*/ -#undef DDR_PHY_DX7GCR6_DXDQVREFR2_DEFVAL -#undef DDR_PHY_DX7GCR6_DXDQVREFR2_SHIFT -#undef DDR_PHY_DX7GCR6_DXDQVREFR2_MASK -#define DDR_PHY_DX7GCR6_DXDQVREFR2_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR6_DXDQVREFR2_SHIFT 16 -#define DDR_PHY_DX7GCR6_DXDQVREFR2_MASK 0x003F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX7GCR6_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DX7GCR6_RESERVED_15_14_SHIFT -#undef DDR_PHY_DX7GCR6_RESERVED_15_14_MASK -#define DDR_PHY_DX7GCR6_RESERVED_15_14_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR6_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DX7GCR6_RESERVED_15_14_MASK 0x0000C000U - -/*DRAM DQ VREF Select for Rank1*/ -#undef DDR_PHY_DX7GCR6_DXDQVREFR1_DEFVAL -#undef DDR_PHY_DX7GCR6_DXDQVREFR1_SHIFT -#undef DDR_PHY_DX7GCR6_DXDQVREFR1_MASK -#define DDR_PHY_DX7GCR6_DXDQVREFR1_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR6_DXDQVREFR1_SHIFT 8 -#define DDR_PHY_DX7GCR6_DXDQVREFR1_MASK 0x00003F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX7GCR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX7GCR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX7GCR6_RESERVED_7_6_MASK -#define DDR_PHY_DX7GCR6_RESERVED_7_6_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX7GCR6_RESERVED_7_6_MASK 0x000000C0U - -/*DRAM DQ VREF Select for Rank0*/ -#undef DDR_PHY_DX7GCR6_DXDQVREFR0_DEFVAL -#undef DDR_PHY_DX7GCR6_DXDQVREFR0_SHIFT -#undef DDR_PHY_DX7GCR6_DXDQVREFR0_MASK -#define DDR_PHY_DX7GCR6_DXDQVREFR0_DEFVAL 0x09090909 -#define DDR_PHY_DX7GCR6_DXDQVREFR0_SHIFT 0 -#define DDR_PHY_DX7GCR6_DXDQVREFR0_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX7LCDLR2_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX7LCDLR2_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX7LCDLR2_RESERVED_31_25_MASK -#define DDR_PHY_DX7LCDLR2_RESERVED_31_25_DEFVAL 0x00000000 -#define DDR_PHY_DX7LCDLR2_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX7LCDLR2_RESERVED_31_25_MASK 0xFE000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX7LCDLR2_RESERVED_24_16_DEFVAL -#undef DDR_PHY_DX7LCDLR2_RESERVED_24_16_SHIFT -#undef DDR_PHY_DX7LCDLR2_RESERVED_24_16_MASK -#define DDR_PHY_DX7LCDLR2_RESERVED_24_16_DEFVAL 0x00000000 -#define DDR_PHY_DX7LCDLR2_RESERVED_24_16_SHIFT 16 -#define DDR_PHY_DX7LCDLR2_RESERVED_24_16_MASK 0x01FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX7LCDLR2_RESERVED_15_9_DEFVAL -#undef DDR_PHY_DX7LCDLR2_RESERVED_15_9_SHIFT -#undef DDR_PHY_DX7LCDLR2_RESERVED_15_9_MASK -#define DDR_PHY_DX7LCDLR2_RESERVED_15_9_DEFVAL 0x00000000 -#define DDR_PHY_DX7LCDLR2_RESERVED_15_9_SHIFT 9 -#define DDR_PHY_DX7LCDLR2_RESERVED_15_9_MASK 0x0000FE00U - -/*Read DQS Gating Delay*/ -#undef DDR_PHY_DX7LCDLR2_DQSGD_DEFVAL -#undef DDR_PHY_DX7LCDLR2_DQSGD_SHIFT -#undef DDR_PHY_DX7LCDLR2_DQSGD_MASK -#define DDR_PHY_DX7LCDLR2_DQSGD_DEFVAL 0x00000000 -#define DDR_PHY_DX7LCDLR2_DQSGD_SHIFT 0 -#define DDR_PHY_DX7LCDLR2_DQSGD_MASK 0x000001FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX7GTR0_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX7GTR0_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX7GTR0_RESERVED_31_24_MASK -#define DDR_PHY_DX7GTR0_RESERVED_31_24_DEFVAL 0x00020000 -#define DDR_PHY_DX7GTR0_RESERVED_31_24_SHIFT 27 -#define DDR_PHY_DX7GTR0_RESERVED_31_24_MASK 0xF8000000U - -/*DQ Write Path Latency Pipeline*/ -#undef DDR_PHY_DX7GTR0_WDQSL_DEFVAL -#undef DDR_PHY_DX7GTR0_WDQSL_SHIFT -#undef DDR_PHY_DX7GTR0_WDQSL_MASK -#define DDR_PHY_DX7GTR0_WDQSL_DEFVAL 0x00020000 -#define DDR_PHY_DX7GTR0_WDQSL_SHIFT 24 -#define DDR_PHY_DX7GTR0_WDQSL_MASK 0x07000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX7GTR0_RESERVED_23_20_DEFVAL -#undef DDR_PHY_DX7GTR0_RESERVED_23_20_SHIFT -#undef DDR_PHY_DX7GTR0_RESERVED_23_20_MASK -#define DDR_PHY_DX7GTR0_RESERVED_23_20_DEFVAL 0x00020000 -#define DDR_PHY_DX7GTR0_RESERVED_23_20_SHIFT 20 -#define DDR_PHY_DX7GTR0_RESERVED_23_20_MASK 0x00F00000U - -/*Write Leveling System Latency*/ -#undef DDR_PHY_DX7GTR0_WLSL_DEFVAL -#undef DDR_PHY_DX7GTR0_WLSL_SHIFT -#undef DDR_PHY_DX7GTR0_WLSL_MASK -#define DDR_PHY_DX7GTR0_WLSL_DEFVAL 0x00020000 -#define DDR_PHY_DX7GTR0_WLSL_SHIFT 16 -#define DDR_PHY_DX7GTR0_WLSL_MASK 0x000F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX7GTR0_RESERVED_15_13_DEFVAL -#undef DDR_PHY_DX7GTR0_RESERVED_15_13_SHIFT -#undef DDR_PHY_DX7GTR0_RESERVED_15_13_MASK -#define DDR_PHY_DX7GTR0_RESERVED_15_13_DEFVAL 0x00020000 -#define DDR_PHY_DX7GTR0_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_DX7GTR0_RESERVED_15_13_MASK 0x0000E000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX7GTR0_RESERVED_12_8_DEFVAL -#undef DDR_PHY_DX7GTR0_RESERVED_12_8_SHIFT -#undef DDR_PHY_DX7GTR0_RESERVED_12_8_MASK -#define DDR_PHY_DX7GTR0_RESERVED_12_8_DEFVAL 0x00020000 -#define DDR_PHY_DX7GTR0_RESERVED_12_8_SHIFT 8 -#define DDR_PHY_DX7GTR0_RESERVED_12_8_MASK 0x00001F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX7GTR0_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DX7GTR0_RESERVED_7_5_SHIFT -#undef DDR_PHY_DX7GTR0_RESERVED_7_5_MASK -#define DDR_PHY_DX7GTR0_RESERVED_7_5_DEFVAL 0x00020000 -#define DDR_PHY_DX7GTR0_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DX7GTR0_RESERVED_7_5_MASK 0x000000E0U - -/*DQS Gating System Latency*/ -#undef DDR_PHY_DX7GTR0_DGSL_DEFVAL -#undef DDR_PHY_DX7GTR0_DGSL_SHIFT -#undef DDR_PHY_DX7GTR0_DGSL_MASK -#define DDR_PHY_DX7GTR0_DGSL_DEFVAL 0x00020000 -#define DDR_PHY_DX7GTR0_DGSL_SHIFT 0 -#define DDR_PHY_DX7GTR0_DGSL_MASK 0x0000001FU - -/*Calibration Bypass*/ -#undef DDR_PHY_DX8GCR0_CALBYP_DEFVAL -#undef DDR_PHY_DX8GCR0_CALBYP_SHIFT -#undef DDR_PHY_DX8GCR0_CALBYP_MASK -#define DDR_PHY_DX8GCR0_CALBYP_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_CALBYP_SHIFT 31 -#define DDR_PHY_DX8GCR0_CALBYP_MASK 0x80000000U - -/*Master Delay Line Enable*/ -#undef DDR_PHY_DX8GCR0_MDLEN_DEFVAL -#undef DDR_PHY_DX8GCR0_MDLEN_SHIFT -#undef DDR_PHY_DX8GCR0_MDLEN_MASK -#define DDR_PHY_DX8GCR0_MDLEN_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_MDLEN_SHIFT 30 -#define DDR_PHY_DX8GCR0_MDLEN_MASK 0x40000000U - -/*Configurable ODT(TE) Phase Shift*/ -#undef DDR_PHY_DX8GCR0_CODTSHFT_DEFVAL -#undef DDR_PHY_DX8GCR0_CODTSHFT_SHIFT -#undef DDR_PHY_DX8GCR0_CODTSHFT_MASK -#define DDR_PHY_DX8GCR0_CODTSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_CODTSHFT_SHIFT 28 -#define DDR_PHY_DX8GCR0_CODTSHFT_MASK 0x30000000U - -/*DQS Duty Cycle Correction*/ -#undef DDR_PHY_DX8GCR0_DQSDCC_DEFVAL -#undef DDR_PHY_DX8GCR0_DQSDCC_SHIFT -#undef DDR_PHY_DX8GCR0_DQSDCC_MASK -#define DDR_PHY_DX8GCR0_DQSDCC_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_DQSDCC_SHIFT 24 -#define DDR_PHY_DX8GCR0_DQSDCC_MASK 0x0F000000U - -/*Number of Cycles ( in terms of ctl_clk) to generate ctl_dx_get_static_rd input for the respective bypte lane of the PHY*/ -#undef DDR_PHY_DX8GCR0_RDDLY_DEFVAL -#undef DDR_PHY_DX8GCR0_RDDLY_SHIFT -#undef DDR_PHY_DX8GCR0_RDDLY_MASK -#define DDR_PHY_DX8GCR0_RDDLY_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_RDDLY_SHIFT 20 -#define DDR_PHY_DX8GCR0_RDDLY_MASK 0x00F00000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8GCR0_RESERVED_19_14_DEFVAL -#undef DDR_PHY_DX8GCR0_RESERVED_19_14_SHIFT -#undef DDR_PHY_DX8GCR0_RESERVED_19_14_MASK -#define DDR_PHY_DX8GCR0_RESERVED_19_14_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_RESERVED_19_14_SHIFT 14 -#define DDR_PHY_DX8GCR0_RESERVED_19_14_MASK 0x000FC000U - -/*DQSNSE Power Down Receiver*/ -#undef DDR_PHY_DX8GCR0_DQSNSEPDR_DEFVAL -#undef DDR_PHY_DX8GCR0_DQSNSEPDR_SHIFT -#undef DDR_PHY_DX8GCR0_DQSNSEPDR_MASK -#define DDR_PHY_DX8GCR0_DQSNSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_DQSNSEPDR_SHIFT 13 -#define DDR_PHY_DX8GCR0_DQSNSEPDR_MASK 0x00002000U - -/*DQSSE Power Down Receiver*/ -#undef DDR_PHY_DX8GCR0_DQSSEPDR_DEFVAL -#undef DDR_PHY_DX8GCR0_DQSSEPDR_SHIFT -#undef DDR_PHY_DX8GCR0_DQSSEPDR_MASK -#define DDR_PHY_DX8GCR0_DQSSEPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_DQSSEPDR_SHIFT 12 -#define DDR_PHY_DX8GCR0_DQSSEPDR_MASK 0x00001000U - -/*RTT On Additive Latency*/ -#undef DDR_PHY_DX8GCR0_RTTOAL_DEFVAL -#undef DDR_PHY_DX8GCR0_RTTOAL_SHIFT -#undef DDR_PHY_DX8GCR0_RTTOAL_MASK -#define DDR_PHY_DX8GCR0_RTTOAL_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_RTTOAL_SHIFT 11 -#define DDR_PHY_DX8GCR0_RTTOAL_MASK 0x00000800U - -/*RTT Output Hold*/ -#undef DDR_PHY_DX8GCR0_RTTOH_DEFVAL -#undef DDR_PHY_DX8GCR0_RTTOH_SHIFT -#undef DDR_PHY_DX8GCR0_RTTOH_MASK -#define DDR_PHY_DX8GCR0_RTTOH_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_RTTOH_SHIFT 9 -#define DDR_PHY_DX8GCR0_RTTOH_MASK 0x00000600U - -/*Configurable PDR Phase Shift*/ -#undef DDR_PHY_DX8GCR0_CPDRSHFT_DEFVAL -#undef DDR_PHY_DX8GCR0_CPDRSHFT_SHIFT -#undef DDR_PHY_DX8GCR0_CPDRSHFT_MASK -#define DDR_PHY_DX8GCR0_CPDRSHFT_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_CPDRSHFT_SHIFT 7 -#define DDR_PHY_DX8GCR0_CPDRSHFT_MASK 0x00000180U - -/*DQSR Power Down*/ -#undef DDR_PHY_DX8GCR0_DQSRPD_DEFVAL -#undef DDR_PHY_DX8GCR0_DQSRPD_SHIFT -#undef DDR_PHY_DX8GCR0_DQSRPD_MASK -#define DDR_PHY_DX8GCR0_DQSRPD_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_DQSRPD_SHIFT 6 -#define DDR_PHY_DX8GCR0_DQSRPD_MASK 0x00000040U - -/*DQSG Power Down Receiver*/ -#undef DDR_PHY_DX8GCR0_DQSGPDR_DEFVAL -#undef DDR_PHY_DX8GCR0_DQSGPDR_SHIFT -#undef DDR_PHY_DX8GCR0_DQSGPDR_MASK -#define DDR_PHY_DX8GCR0_DQSGPDR_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_DQSGPDR_SHIFT 5 -#define DDR_PHY_DX8GCR0_DQSGPDR_MASK 0x00000020U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8GCR0_RESERVED_4_DEFVAL -#undef DDR_PHY_DX8GCR0_RESERVED_4_SHIFT -#undef DDR_PHY_DX8GCR0_RESERVED_4_MASK -#define DDR_PHY_DX8GCR0_RESERVED_4_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_RESERVED_4_SHIFT 4 -#define DDR_PHY_DX8GCR0_RESERVED_4_MASK 0x00000010U - -/*DQSG On-Die Termination*/ -#undef DDR_PHY_DX8GCR0_DQSGODT_DEFVAL -#undef DDR_PHY_DX8GCR0_DQSGODT_SHIFT -#undef DDR_PHY_DX8GCR0_DQSGODT_MASK -#define DDR_PHY_DX8GCR0_DQSGODT_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_DQSGODT_SHIFT 3 -#define DDR_PHY_DX8GCR0_DQSGODT_MASK 0x00000008U - -/*DQSG Output Enable*/ -#undef DDR_PHY_DX8GCR0_DQSGOE_DEFVAL -#undef DDR_PHY_DX8GCR0_DQSGOE_SHIFT -#undef DDR_PHY_DX8GCR0_DQSGOE_MASK -#define DDR_PHY_DX8GCR0_DQSGOE_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_DQSGOE_SHIFT 2 -#define DDR_PHY_DX8GCR0_DQSGOE_MASK 0x00000004U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8GCR0_RESERVED_1_0_DEFVAL -#undef DDR_PHY_DX8GCR0_RESERVED_1_0_SHIFT -#undef DDR_PHY_DX8GCR0_RESERVED_1_0_MASK -#define DDR_PHY_DX8GCR0_RESERVED_1_0_DEFVAL 0x40200204 -#define DDR_PHY_DX8GCR0_RESERVED_1_0_SHIFT 0 -#define DDR_PHY_DX8GCR0_RESERVED_1_0_MASK 0x00000003U - -/*Enables the PDR mode for DQ[7:0]*/ -#undef DDR_PHY_DX8GCR1_DXPDRMODE_DEFVAL -#undef DDR_PHY_DX8GCR1_DXPDRMODE_SHIFT -#undef DDR_PHY_DX8GCR1_DXPDRMODE_MASK -#define DDR_PHY_DX8GCR1_DXPDRMODE_DEFVAL 0x00007FFF -#define DDR_PHY_DX8GCR1_DXPDRMODE_SHIFT 16 -#define DDR_PHY_DX8GCR1_DXPDRMODE_MASK 0xFFFF0000U - -/*Reserved. Returns zeroes on reads.*/ -#undef DDR_PHY_DX8GCR1_RESERVED_15_DEFVAL -#undef DDR_PHY_DX8GCR1_RESERVED_15_SHIFT -#undef DDR_PHY_DX8GCR1_RESERVED_15_MASK -#define DDR_PHY_DX8GCR1_RESERVED_15_DEFVAL 0x00007FFF -#define DDR_PHY_DX8GCR1_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX8GCR1_RESERVED_15_MASK 0x00008000U - -/*Select the delayed or non-delayed read data strobe #*/ -#undef DDR_PHY_DX8GCR1_QSNSEL_DEFVAL -#undef DDR_PHY_DX8GCR1_QSNSEL_SHIFT -#undef DDR_PHY_DX8GCR1_QSNSEL_MASK -#define DDR_PHY_DX8GCR1_QSNSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX8GCR1_QSNSEL_SHIFT 14 -#define DDR_PHY_DX8GCR1_QSNSEL_MASK 0x00004000U - -/*Select the delayed or non-delayed read data strobe*/ -#undef DDR_PHY_DX8GCR1_QSSEL_DEFVAL -#undef DDR_PHY_DX8GCR1_QSSEL_SHIFT -#undef DDR_PHY_DX8GCR1_QSSEL_MASK -#define DDR_PHY_DX8GCR1_QSSEL_DEFVAL 0x00007FFF -#define DDR_PHY_DX8GCR1_QSSEL_SHIFT 13 -#define DDR_PHY_DX8GCR1_QSSEL_MASK 0x00002000U - -/*Enables Read Data Strobe in a byte lane*/ -#undef DDR_PHY_DX8GCR1_OEEN_DEFVAL -#undef DDR_PHY_DX8GCR1_OEEN_SHIFT -#undef DDR_PHY_DX8GCR1_OEEN_MASK -#define DDR_PHY_DX8GCR1_OEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX8GCR1_OEEN_SHIFT 12 -#define DDR_PHY_DX8GCR1_OEEN_MASK 0x00001000U - -/*Enables PDR in a byte lane*/ -#undef DDR_PHY_DX8GCR1_PDREN_DEFVAL -#undef DDR_PHY_DX8GCR1_PDREN_SHIFT -#undef DDR_PHY_DX8GCR1_PDREN_MASK -#define DDR_PHY_DX8GCR1_PDREN_DEFVAL 0x00007FFF -#define DDR_PHY_DX8GCR1_PDREN_SHIFT 11 -#define DDR_PHY_DX8GCR1_PDREN_MASK 0x00000800U - -/*Enables ODT/TE in a byte lane*/ -#undef DDR_PHY_DX8GCR1_TEEN_DEFVAL -#undef DDR_PHY_DX8GCR1_TEEN_SHIFT -#undef DDR_PHY_DX8GCR1_TEEN_MASK -#define DDR_PHY_DX8GCR1_TEEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX8GCR1_TEEN_SHIFT 10 -#define DDR_PHY_DX8GCR1_TEEN_MASK 0x00000400U - -/*Enables Write Data strobe in a byte lane*/ -#undef DDR_PHY_DX8GCR1_DSEN_DEFVAL -#undef DDR_PHY_DX8GCR1_DSEN_SHIFT -#undef DDR_PHY_DX8GCR1_DSEN_MASK -#define DDR_PHY_DX8GCR1_DSEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX8GCR1_DSEN_SHIFT 9 -#define DDR_PHY_DX8GCR1_DSEN_MASK 0x00000200U - -/*Enables DM pin in a byte lane*/ -#undef DDR_PHY_DX8GCR1_DMEN_DEFVAL -#undef DDR_PHY_DX8GCR1_DMEN_SHIFT -#undef DDR_PHY_DX8GCR1_DMEN_MASK -#define DDR_PHY_DX8GCR1_DMEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX8GCR1_DMEN_SHIFT 8 -#define DDR_PHY_DX8GCR1_DMEN_MASK 0x00000100U - -/*Enables DQ corresponding to each bit in a byte*/ -#undef DDR_PHY_DX8GCR1_DQEN_DEFVAL -#undef DDR_PHY_DX8GCR1_DQEN_SHIFT -#undef DDR_PHY_DX8GCR1_DQEN_MASK -#define DDR_PHY_DX8GCR1_DQEN_DEFVAL 0x00007FFF -#define DDR_PHY_DX8GCR1_DQEN_SHIFT 0 -#define DDR_PHY_DX8GCR1_DQEN_MASK 0x000000FFU - -/*Byte lane VREF IOM (Used only by D4MU IOs)*/ -#undef DDR_PHY_DX8GCR4_RESERVED_31_29_DEFVAL -#undef DDR_PHY_DX8GCR4_RESERVED_31_29_SHIFT -#undef DDR_PHY_DX8GCR4_RESERVED_31_29_MASK -#define DDR_PHY_DX8GCR4_RESERVED_31_29_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_RESERVED_31_29_SHIFT 29 -#define DDR_PHY_DX8GCR4_RESERVED_31_29_MASK 0xE0000000U - -/*Byte Lane VREF Pad Enable*/ -#undef DDR_PHY_DX8GCR4_DXREFPEN_DEFVAL -#undef DDR_PHY_DX8GCR4_DXREFPEN_SHIFT -#undef DDR_PHY_DX8GCR4_DXREFPEN_MASK -#define DDR_PHY_DX8GCR4_DXREFPEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_DXREFPEN_SHIFT 28 -#define DDR_PHY_DX8GCR4_DXREFPEN_MASK 0x10000000U - -/*Byte Lane Internal VREF Enable*/ -#undef DDR_PHY_DX8GCR4_DXREFEEN_DEFVAL -#undef DDR_PHY_DX8GCR4_DXREFEEN_SHIFT -#undef DDR_PHY_DX8GCR4_DXREFEEN_MASK -#define DDR_PHY_DX8GCR4_DXREFEEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_DXREFEEN_SHIFT 26 -#define DDR_PHY_DX8GCR4_DXREFEEN_MASK 0x0C000000U - -/*Byte Lane Single-End VREF Enable*/ -#undef DDR_PHY_DX8GCR4_DXREFSEN_DEFVAL -#undef DDR_PHY_DX8GCR4_DXREFSEN_SHIFT -#undef DDR_PHY_DX8GCR4_DXREFSEN_MASK -#define DDR_PHY_DX8GCR4_DXREFSEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_DXREFSEN_SHIFT 25 -#define DDR_PHY_DX8GCR4_DXREFSEN_MASK 0x02000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX8GCR4_RESERVED_24_DEFVAL -#undef DDR_PHY_DX8GCR4_RESERVED_24_SHIFT -#undef DDR_PHY_DX8GCR4_RESERVED_24_MASK -#define DDR_PHY_DX8GCR4_RESERVED_24_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_RESERVED_24_SHIFT 24 -#define DDR_PHY_DX8GCR4_RESERVED_24_MASK 0x01000000U - -/*External VREF generator REFSEL range select*/ -#undef DDR_PHY_DX8GCR4_DXREFESELRANGE_DEFVAL -#undef DDR_PHY_DX8GCR4_DXREFESELRANGE_SHIFT -#undef DDR_PHY_DX8GCR4_DXREFESELRANGE_MASK -#define DDR_PHY_DX8GCR4_DXREFESELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_DXREFESELRANGE_SHIFT 23 -#define DDR_PHY_DX8GCR4_DXREFESELRANGE_MASK 0x00800000U - -/*Byte Lane External VREF Select*/ -#undef DDR_PHY_DX8GCR4_DXREFESEL_DEFVAL -#undef DDR_PHY_DX8GCR4_DXREFESEL_SHIFT -#undef DDR_PHY_DX8GCR4_DXREFESEL_MASK -#define DDR_PHY_DX8GCR4_DXREFESEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_DXREFESEL_SHIFT 16 -#define DDR_PHY_DX8GCR4_DXREFESEL_MASK 0x007F0000U - -/*Single ended VREF generator REFSEL range select*/ -#undef DDR_PHY_DX8GCR4_DXREFSSELRANGE_DEFVAL -#undef DDR_PHY_DX8GCR4_DXREFSSELRANGE_SHIFT -#undef DDR_PHY_DX8GCR4_DXREFSSELRANGE_MASK -#define DDR_PHY_DX8GCR4_DXREFSSELRANGE_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_DXREFSSELRANGE_SHIFT 15 -#define DDR_PHY_DX8GCR4_DXREFSSELRANGE_MASK 0x00008000U - -/*Byte Lane Single-End VREF Select*/ -#undef DDR_PHY_DX8GCR4_DXREFSSEL_DEFVAL -#undef DDR_PHY_DX8GCR4_DXREFSSEL_SHIFT -#undef DDR_PHY_DX8GCR4_DXREFSSEL_MASK -#define DDR_PHY_DX8GCR4_DXREFSSEL_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_DXREFSSEL_SHIFT 8 -#define DDR_PHY_DX8GCR4_DXREFSSEL_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX8GCR4_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX8GCR4_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX8GCR4_RESERVED_7_6_MASK -#define DDR_PHY_DX8GCR4_RESERVED_7_6_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX8GCR4_RESERVED_7_6_MASK 0x000000C0U - -/*VREF Enable control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX8GCR4_DXREFIEN_DEFVAL -#undef DDR_PHY_DX8GCR4_DXREFIEN_SHIFT -#undef DDR_PHY_DX8GCR4_DXREFIEN_MASK -#define DDR_PHY_DX8GCR4_DXREFIEN_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_DXREFIEN_SHIFT 2 -#define DDR_PHY_DX8GCR4_DXREFIEN_MASK 0x0000003CU - -/*VRMON control for DQ IO (Single Ended) buffers of a byte lane.*/ -#undef DDR_PHY_DX8GCR4_DXREFIMON_DEFVAL -#undef DDR_PHY_DX8GCR4_DXREFIMON_SHIFT -#undef DDR_PHY_DX8GCR4_DXREFIMON_MASK -#define DDR_PHY_DX8GCR4_DXREFIMON_DEFVAL 0x0E00003C -#define DDR_PHY_DX8GCR4_DXREFIMON_SHIFT 0 -#define DDR_PHY_DX8GCR4_DXREFIMON_MASK 0x00000003U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX8GCR5_RESERVED_31_DEFVAL -#undef DDR_PHY_DX8GCR5_RESERVED_31_SHIFT -#undef DDR_PHY_DX8GCR5_RESERVED_31_MASK -#define DDR_PHY_DX8GCR5_RESERVED_31_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR5_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX8GCR5_RESERVED_31_MASK 0x80000000U - -/*Byte Lane internal VREF Select for Rank 3*/ -#undef DDR_PHY_DX8GCR5_DXREFISELR3_DEFVAL -#undef DDR_PHY_DX8GCR5_DXREFISELR3_SHIFT -#undef DDR_PHY_DX8GCR5_DXREFISELR3_MASK -#define DDR_PHY_DX8GCR5_DXREFISELR3_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR5_DXREFISELR3_SHIFT 24 -#define DDR_PHY_DX8GCR5_DXREFISELR3_MASK 0x7F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX8GCR5_RESERVED_23_DEFVAL -#undef DDR_PHY_DX8GCR5_RESERVED_23_SHIFT -#undef DDR_PHY_DX8GCR5_RESERVED_23_MASK -#define DDR_PHY_DX8GCR5_RESERVED_23_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR5_RESERVED_23_SHIFT 23 -#define DDR_PHY_DX8GCR5_RESERVED_23_MASK 0x00800000U - -/*Byte Lane internal VREF Select for Rank 2*/ -#undef DDR_PHY_DX8GCR5_DXREFISELR2_DEFVAL -#undef DDR_PHY_DX8GCR5_DXREFISELR2_SHIFT -#undef DDR_PHY_DX8GCR5_DXREFISELR2_MASK -#define DDR_PHY_DX8GCR5_DXREFISELR2_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR5_DXREFISELR2_SHIFT 16 -#define DDR_PHY_DX8GCR5_DXREFISELR2_MASK 0x007F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX8GCR5_RESERVED_15_DEFVAL -#undef DDR_PHY_DX8GCR5_RESERVED_15_SHIFT -#undef DDR_PHY_DX8GCR5_RESERVED_15_MASK -#define DDR_PHY_DX8GCR5_RESERVED_15_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR5_RESERVED_15_SHIFT 15 -#define DDR_PHY_DX8GCR5_RESERVED_15_MASK 0x00008000U - -/*Byte Lane internal VREF Select for Rank 1*/ -#undef DDR_PHY_DX8GCR5_DXREFISELR1_DEFVAL -#undef DDR_PHY_DX8GCR5_DXREFISELR1_SHIFT -#undef DDR_PHY_DX8GCR5_DXREFISELR1_MASK -#define DDR_PHY_DX8GCR5_DXREFISELR1_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR5_DXREFISELR1_SHIFT 8 -#define DDR_PHY_DX8GCR5_DXREFISELR1_MASK 0x00007F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX8GCR5_RESERVED_7_DEFVAL -#undef DDR_PHY_DX8GCR5_RESERVED_7_SHIFT -#undef DDR_PHY_DX8GCR5_RESERVED_7_MASK -#define DDR_PHY_DX8GCR5_RESERVED_7_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR5_RESERVED_7_SHIFT 7 -#define DDR_PHY_DX8GCR5_RESERVED_7_MASK 0x00000080U - -/*Byte Lane internal VREF Select for Rank 0*/ -#undef DDR_PHY_DX8GCR5_DXREFISELR0_DEFVAL -#undef DDR_PHY_DX8GCR5_DXREFISELR0_SHIFT -#undef DDR_PHY_DX8GCR5_DXREFISELR0_MASK -#define DDR_PHY_DX8GCR5_DXREFISELR0_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR5_DXREFISELR0_SHIFT 0 -#define DDR_PHY_DX8GCR5_DXREFISELR0_MASK 0x0000007FU - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX8GCR6_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX8GCR6_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX8GCR6_RESERVED_31_30_MASK -#define DDR_PHY_DX8GCR6_RESERVED_31_30_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR6_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX8GCR6_RESERVED_31_30_MASK 0xC0000000U - -/*DRAM DQ VREF Select for Rank3*/ -#undef DDR_PHY_DX8GCR6_DXDQVREFR3_DEFVAL -#undef DDR_PHY_DX8GCR6_DXDQVREFR3_SHIFT -#undef DDR_PHY_DX8GCR6_DXDQVREFR3_MASK -#define DDR_PHY_DX8GCR6_DXDQVREFR3_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR6_DXDQVREFR3_SHIFT 24 -#define DDR_PHY_DX8GCR6_DXDQVREFR3_MASK 0x3F000000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX8GCR6_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX8GCR6_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX8GCR6_RESERVED_23_22_MASK -#define DDR_PHY_DX8GCR6_RESERVED_23_22_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR6_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX8GCR6_RESERVED_23_22_MASK 0x00C00000U - -/*DRAM DQ VREF Select for Rank2*/ -#undef DDR_PHY_DX8GCR6_DXDQVREFR2_DEFVAL -#undef DDR_PHY_DX8GCR6_DXDQVREFR2_SHIFT -#undef DDR_PHY_DX8GCR6_DXDQVREFR2_MASK -#define DDR_PHY_DX8GCR6_DXDQVREFR2_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR6_DXDQVREFR2_SHIFT 16 -#define DDR_PHY_DX8GCR6_DXDQVREFR2_MASK 0x003F0000U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX8GCR6_RESERVED_15_14_DEFVAL -#undef DDR_PHY_DX8GCR6_RESERVED_15_14_SHIFT -#undef DDR_PHY_DX8GCR6_RESERVED_15_14_MASK -#define DDR_PHY_DX8GCR6_RESERVED_15_14_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR6_RESERVED_15_14_SHIFT 14 -#define DDR_PHY_DX8GCR6_RESERVED_15_14_MASK 0x0000C000U - -/*DRAM DQ VREF Select for Rank1*/ -#undef DDR_PHY_DX8GCR6_DXDQVREFR1_DEFVAL -#undef DDR_PHY_DX8GCR6_DXDQVREFR1_SHIFT -#undef DDR_PHY_DX8GCR6_DXDQVREFR1_MASK -#define DDR_PHY_DX8GCR6_DXDQVREFR1_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR6_DXDQVREFR1_SHIFT 8 -#define DDR_PHY_DX8GCR6_DXDQVREFR1_MASK 0x00003F00U - -/*Reserved. Returns zeros on reads.*/ -#undef DDR_PHY_DX8GCR6_RESERVED_7_6_DEFVAL -#undef DDR_PHY_DX8GCR6_RESERVED_7_6_SHIFT -#undef DDR_PHY_DX8GCR6_RESERVED_7_6_MASK -#define DDR_PHY_DX8GCR6_RESERVED_7_6_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR6_RESERVED_7_6_SHIFT 6 -#define DDR_PHY_DX8GCR6_RESERVED_7_6_MASK 0x000000C0U - -/*DRAM DQ VREF Select for Rank0*/ -#undef DDR_PHY_DX8GCR6_DXDQVREFR0_DEFVAL -#undef DDR_PHY_DX8GCR6_DXDQVREFR0_SHIFT -#undef DDR_PHY_DX8GCR6_DXDQVREFR0_MASK -#define DDR_PHY_DX8GCR6_DXDQVREFR0_DEFVAL 0x09090909 -#define DDR_PHY_DX8GCR6_DXDQVREFR0_SHIFT 0 -#define DDR_PHY_DX8GCR6_DXDQVREFR0_MASK 0x0000003FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8LCDLR2_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX8LCDLR2_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX8LCDLR2_RESERVED_31_25_MASK -#define DDR_PHY_DX8LCDLR2_RESERVED_31_25_DEFVAL 0x00000000 -#define DDR_PHY_DX8LCDLR2_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX8LCDLR2_RESERVED_31_25_MASK 0xFE000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8LCDLR2_RESERVED_24_16_DEFVAL -#undef DDR_PHY_DX8LCDLR2_RESERVED_24_16_SHIFT -#undef DDR_PHY_DX8LCDLR2_RESERVED_24_16_MASK -#define DDR_PHY_DX8LCDLR2_RESERVED_24_16_DEFVAL 0x00000000 -#define DDR_PHY_DX8LCDLR2_RESERVED_24_16_SHIFT 16 -#define DDR_PHY_DX8LCDLR2_RESERVED_24_16_MASK 0x01FF0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8LCDLR2_RESERVED_15_9_DEFVAL -#undef DDR_PHY_DX8LCDLR2_RESERVED_15_9_SHIFT -#undef DDR_PHY_DX8LCDLR2_RESERVED_15_9_MASK -#define DDR_PHY_DX8LCDLR2_RESERVED_15_9_DEFVAL 0x00000000 -#define DDR_PHY_DX8LCDLR2_RESERVED_15_9_SHIFT 9 -#define DDR_PHY_DX8LCDLR2_RESERVED_15_9_MASK 0x0000FE00U - -/*Read DQS Gating Delay*/ -#undef DDR_PHY_DX8LCDLR2_DQSGD_DEFVAL -#undef DDR_PHY_DX8LCDLR2_DQSGD_SHIFT -#undef DDR_PHY_DX8LCDLR2_DQSGD_MASK -#define DDR_PHY_DX8LCDLR2_DQSGD_DEFVAL 0x00000000 -#define DDR_PHY_DX8LCDLR2_DQSGD_SHIFT 0 -#define DDR_PHY_DX8LCDLR2_DQSGD_MASK 0x000001FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8GTR0_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX8GTR0_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX8GTR0_RESERVED_31_24_MASK -#define DDR_PHY_DX8GTR0_RESERVED_31_24_DEFVAL 0x00020000 -#define DDR_PHY_DX8GTR0_RESERVED_31_24_SHIFT 27 -#define DDR_PHY_DX8GTR0_RESERVED_31_24_MASK 0xF8000000U - -/*DQ Write Path Latency Pipeline*/ -#undef DDR_PHY_DX8GTR0_WDQSL_DEFVAL -#undef DDR_PHY_DX8GTR0_WDQSL_SHIFT -#undef DDR_PHY_DX8GTR0_WDQSL_MASK -#define DDR_PHY_DX8GTR0_WDQSL_DEFVAL 0x00020000 -#define DDR_PHY_DX8GTR0_WDQSL_SHIFT 24 -#define DDR_PHY_DX8GTR0_WDQSL_MASK 0x07000000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8GTR0_RESERVED_23_20_DEFVAL -#undef DDR_PHY_DX8GTR0_RESERVED_23_20_SHIFT -#undef DDR_PHY_DX8GTR0_RESERVED_23_20_MASK -#define DDR_PHY_DX8GTR0_RESERVED_23_20_DEFVAL 0x00020000 -#define DDR_PHY_DX8GTR0_RESERVED_23_20_SHIFT 20 -#define DDR_PHY_DX8GTR0_RESERVED_23_20_MASK 0x00F00000U - -/*Write Leveling System Latency*/ -#undef DDR_PHY_DX8GTR0_WLSL_DEFVAL -#undef DDR_PHY_DX8GTR0_WLSL_SHIFT -#undef DDR_PHY_DX8GTR0_WLSL_MASK -#define DDR_PHY_DX8GTR0_WLSL_DEFVAL 0x00020000 -#define DDR_PHY_DX8GTR0_WLSL_SHIFT 16 -#define DDR_PHY_DX8GTR0_WLSL_MASK 0x000F0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8GTR0_RESERVED_15_13_DEFVAL -#undef DDR_PHY_DX8GTR0_RESERVED_15_13_SHIFT -#undef DDR_PHY_DX8GTR0_RESERVED_15_13_MASK -#define DDR_PHY_DX8GTR0_RESERVED_15_13_DEFVAL 0x00020000 -#define DDR_PHY_DX8GTR0_RESERVED_15_13_SHIFT 13 -#define DDR_PHY_DX8GTR0_RESERVED_15_13_MASK 0x0000E000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8GTR0_RESERVED_12_8_DEFVAL -#undef DDR_PHY_DX8GTR0_RESERVED_12_8_SHIFT -#undef DDR_PHY_DX8GTR0_RESERVED_12_8_MASK -#define DDR_PHY_DX8GTR0_RESERVED_12_8_DEFVAL 0x00020000 -#define DDR_PHY_DX8GTR0_RESERVED_12_8_SHIFT 8 -#define DDR_PHY_DX8GTR0_RESERVED_12_8_MASK 0x00001F00U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8GTR0_RESERVED_7_5_DEFVAL -#undef DDR_PHY_DX8GTR0_RESERVED_7_5_SHIFT -#undef DDR_PHY_DX8GTR0_RESERVED_7_5_MASK -#define DDR_PHY_DX8GTR0_RESERVED_7_5_DEFVAL 0x00020000 -#define DDR_PHY_DX8GTR0_RESERVED_7_5_SHIFT 5 -#define DDR_PHY_DX8GTR0_RESERVED_7_5_MASK 0x000000E0U - -/*DQS Gating System Latency*/ -#undef DDR_PHY_DX8GTR0_DGSL_DEFVAL -#undef DDR_PHY_DX8GTR0_DGSL_SHIFT -#undef DDR_PHY_DX8GTR0_DGSL_MASK -#define DDR_PHY_DX8GTR0_DGSL_DEFVAL 0x00020000 -#define DDR_PHY_DX8GTR0_DGSL_SHIFT 0 -#define DDR_PHY_DX8GTR0_DGSL_MASK 0x0000001FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL0OSC_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX8SL0OSC_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX8SL0OSC_RESERVED_31_30_MASK -#define DDR_PHY_DX8SL0OSC_RESERVED_31_30_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX8SL0OSC_RESERVED_31_30_MASK 0xC0000000U - -/*Enable Clock Gating for DX ddr_clk*/ -#undef DDR_PHY_DX8SL0OSC_GATEDXRDCLK_DEFVAL -#undef DDR_PHY_DX8SL0OSC_GATEDXRDCLK_SHIFT -#undef DDR_PHY_DX8SL0OSC_GATEDXRDCLK_MASK -#define DDR_PHY_DX8SL0OSC_GATEDXRDCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_GATEDXRDCLK_SHIFT 28 -#define DDR_PHY_DX8SL0OSC_GATEDXRDCLK_MASK 0x30000000U - -/*Enable Clock Gating for DX ctl_rd_clk*/ -#undef DDR_PHY_DX8SL0OSC_GATEDXDDRCLK_DEFVAL -#undef DDR_PHY_DX8SL0OSC_GATEDXDDRCLK_SHIFT -#undef DDR_PHY_DX8SL0OSC_GATEDXDDRCLK_MASK -#define DDR_PHY_DX8SL0OSC_GATEDXDDRCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_GATEDXDDRCLK_SHIFT 26 -#define DDR_PHY_DX8SL0OSC_GATEDXDDRCLK_MASK 0x0C000000U - -/*Enable Clock Gating for DX ctl_clk*/ -#undef DDR_PHY_DX8SL0OSC_GATEDXCTLCLK_DEFVAL -#undef DDR_PHY_DX8SL0OSC_GATEDXCTLCLK_SHIFT -#undef DDR_PHY_DX8SL0OSC_GATEDXCTLCLK_MASK -#define DDR_PHY_DX8SL0OSC_GATEDXCTLCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_GATEDXCTLCLK_SHIFT 24 -#define DDR_PHY_DX8SL0OSC_GATEDXCTLCLK_MASK 0x03000000U - -/*Selects the level to which clocks will be stalled when clock gating is enabled.*/ -#undef DDR_PHY_DX8SL0OSC_CLKLEVEL_DEFVAL -#undef DDR_PHY_DX8SL0OSC_CLKLEVEL_SHIFT -#undef DDR_PHY_DX8SL0OSC_CLKLEVEL_MASK -#define DDR_PHY_DX8SL0OSC_CLKLEVEL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_CLKLEVEL_SHIFT 22 -#define DDR_PHY_DX8SL0OSC_CLKLEVEL_MASK 0x00C00000U - -/*Loopback Mode*/ -#undef DDR_PHY_DX8SL0OSC_LBMODE_DEFVAL -#undef DDR_PHY_DX8SL0OSC_LBMODE_SHIFT -#undef DDR_PHY_DX8SL0OSC_LBMODE_MASK -#define DDR_PHY_DX8SL0OSC_LBMODE_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_LBMODE_SHIFT 21 -#define DDR_PHY_DX8SL0OSC_LBMODE_MASK 0x00200000U - -/*Load GSDQS LCDL with 2x the calibrated GSDQSPRD value*/ -#undef DDR_PHY_DX8SL0OSC_LBGSDQS_DEFVAL -#undef DDR_PHY_DX8SL0OSC_LBGSDQS_SHIFT -#undef DDR_PHY_DX8SL0OSC_LBGSDQS_MASK -#define DDR_PHY_DX8SL0OSC_LBGSDQS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_LBGSDQS_SHIFT 20 -#define DDR_PHY_DX8SL0OSC_LBGSDQS_MASK 0x00100000U - -/*Loopback DQS Gating*/ -#undef DDR_PHY_DX8SL0OSC_LBGDQS_DEFVAL -#undef DDR_PHY_DX8SL0OSC_LBGDQS_SHIFT -#undef DDR_PHY_DX8SL0OSC_LBGDQS_MASK -#define DDR_PHY_DX8SL0OSC_LBGDQS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_LBGDQS_SHIFT 18 -#define DDR_PHY_DX8SL0OSC_LBGDQS_MASK 0x000C0000U - -/*Loopback DQS Shift*/ -#undef DDR_PHY_DX8SL0OSC_LBDQSS_DEFVAL -#undef DDR_PHY_DX8SL0OSC_LBDQSS_SHIFT -#undef DDR_PHY_DX8SL0OSC_LBDQSS_MASK -#define DDR_PHY_DX8SL0OSC_LBDQSS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_LBDQSS_SHIFT 17 -#define DDR_PHY_DX8SL0OSC_LBDQSS_MASK 0x00020000U - -/*PHY High-Speed Reset*/ -#undef DDR_PHY_DX8SL0OSC_PHYHRST_DEFVAL -#undef DDR_PHY_DX8SL0OSC_PHYHRST_SHIFT -#undef DDR_PHY_DX8SL0OSC_PHYHRST_MASK -#define DDR_PHY_DX8SL0OSC_PHYHRST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_PHYHRST_SHIFT 16 -#define DDR_PHY_DX8SL0OSC_PHYHRST_MASK 0x00010000U - -/*PHY FIFO Reset*/ -#undef DDR_PHY_DX8SL0OSC_PHYFRST_DEFVAL -#undef DDR_PHY_DX8SL0OSC_PHYFRST_SHIFT -#undef DDR_PHY_DX8SL0OSC_PHYFRST_MASK -#define DDR_PHY_DX8SL0OSC_PHYFRST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_PHYFRST_SHIFT 15 -#define DDR_PHY_DX8SL0OSC_PHYFRST_MASK 0x00008000U - -/*Delay Line Test Start*/ -#undef DDR_PHY_DX8SL0OSC_DLTST_DEFVAL -#undef DDR_PHY_DX8SL0OSC_DLTST_SHIFT -#undef DDR_PHY_DX8SL0OSC_DLTST_MASK -#define DDR_PHY_DX8SL0OSC_DLTST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_DLTST_SHIFT 14 -#define DDR_PHY_DX8SL0OSC_DLTST_MASK 0x00004000U - -/*Delay Line Test Mode*/ -#undef DDR_PHY_DX8SL0OSC_DLTMODE_DEFVAL -#undef DDR_PHY_DX8SL0OSC_DLTMODE_SHIFT -#undef DDR_PHY_DX8SL0OSC_DLTMODE_MASK -#define DDR_PHY_DX8SL0OSC_DLTMODE_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_DLTMODE_SHIFT 13 -#define DDR_PHY_DX8SL0OSC_DLTMODE_MASK 0x00002000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8SL0OSC_RESERVED_12_11_DEFVAL -#undef DDR_PHY_DX8SL0OSC_RESERVED_12_11_SHIFT -#undef DDR_PHY_DX8SL0OSC_RESERVED_12_11_MASK -#define DDR_PHY_DX8SL0OSC_RESERVED_12_11_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_RESERVED_12_11_SHIFT 11 -#define DDR_PHY_DX8SL0OSC_RESERVED_12_11_MASK 0x00001800U - -/*Oscillator Mode Write-Data Delay Line Select*/ -#undef DDR_PHY_DX8SL0OSC_OSCWDDL_DEFVAL -#undef DDR_PHY_DX8SL0OSC_OSCWDDL_SHIFT -#undef DDR_PHY_DX8SL0OSC_OSCWDDL_MASK -#define DDR_PHY_DX8SL0OSC_OSCWDDL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_OSCWDDL_SHIFT 9 -#define DDR_PHY_DX8SL0OSC_OSCWDDL_MASK 0x00000600U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8SL0OSC_RESERVED_8_7_DEFVAL -#undef DDR_PHY_DX8SL0OSC_RESERVED_8_7_SHIFT -#undef DDR_PHY_DX8SL0OSC_RESERVED_8_7_MASK -#define DDR_PHY_DX8SL0OSC_RESERVED_8_7_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_RESERVED_8_7_SHIFT 7 -#define DDR_PHY_DX8SL0OSC_RESERVED_8_7_MASK 0x00000180U - -/*Oscillator Mode Write-Leveling Delay Line Select*/ -#undef DDR_PHY_DX8SL0OSC_OSCWDL_DEFVAL -#undef DDR_PHY_DX8SL0OSC_OSCWDL_SHIFT -#undef DDR_PHY_DX8SL0OSC_OSCWDL_MASK -#define DDR_PHY_DX8SL0OSC_OSCWDL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_OSCWDL_SHIFT 5 -#define DDR_PHY_DX8SL0OSC_OSCWDL_MASK 0x00000060U - -/*Oscillator Mode Division*/ -#undef DDR_PHY_DX8SL0OSC_OSCDIV_DEFVAL -#undef DDR_PHY_DX8SL0OSC_OSCDIV_SHIFT -#undef DDR_PHY_DX8SL0OSC_OSCDIV_MASK -#define DDR_PHY_DX8SL0OSC_OSCDIV_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_OSCDIV_SHIFT 1 -#define DDR_PHY_DX8SL0OSC_OSCDIV_MASK 0x0000001EU - -/*Oscillator Enable*/ -#undef DDR_PHY_DX8SL0OSC_OSCEN_DEFVAL -#undef DDR_PHY_DX8SL0OSC_OSCEN_SHIFT -#undef DDR_PHY_DX8SL0OSC_OSCEN_MASK -#define DDR_PHY_DX8SL0OSC_OSCEN_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL0OSC_OSCEN_SHIFT 0 -#define DDR_PHY_DX8SL0OSC_OSCEN_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25_MASK -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_31_25_MASK 0xFE000000U - -/*Read Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SL0DQSCTL_RRRMODE_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_RRRMODE_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_RRRMODE_MASK -#define DDR_PHY_DX8SL0DQSCTL_RRRMODE_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_RRRMODE_SHIFT 24 -#define DDR_PHY_DX8SL0DQSCTL_RRRMODE_MASK 0x01000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22_MASK -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_23_22_MASK 0x00C00000U - -/*Write Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SL0DQSCTL_WRRMODE_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_WRRMODE_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_WRRMODE_MASK -#define DDR_PHY_DX8SL0DQSCTL_WRRMODE_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_WRRMODE_SHIFT 21 -#define DDR_PHY_DX8SL0DQSCTL_WRRMODE_MASK 0x00200000U - -/*DQS Gate Extension*/ -#undef DDR_PHY_DX8SL0DQSCTL_DQSGX_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_DQSGX_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_DQSGX_MASK -#define DDR_PHY_DX8SL0DQSCTL_DQSGX_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_DQSGX_SHIFT 19 -#define DDR_PHY_DX8SL0DQSCTL_DQSGX_MASK 0x00180000U - -/*Low Power PLL Power Down*/ -#undef DDR_PHY_DX8SL0DQSCTL_LPPLLPD_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_LPPLLPD_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_LPPLLPD_MASK -#define DDR_PHY_DX8SL0DQSCTL_LPPLLPD_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_LPPLLPD_SHIFT 18 -#define DDR_PHY_DX8SL0DQSCTL_LPPLLPD_MASK 0x00040000U - -/*Low Power I/O Power Down*/ -#undef DDR_PHY_DX8SL0DQSCTL_LPIOPD_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_LPIOPD_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_LPIOPD_MASK -#define DDR_PHY_DX8SL0DQSCTL_LPIOPD_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_LPIOPD_SHIFT 17 -#define DDR_PHY_DX8SL0DQSCTL_LPIOPD_MASK 0x00020000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15_MASK -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15_SHIFT 15 -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_16_15_MASK 0x00018000U - -/*QS Counter Enable*/ -#undef DDR_PHY_DX8SL0DQSCTL_QSCNTEN_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_QSCNTEN_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_QSCNTEN_MASK -#define DDR_PHY_DX8SL0DQSCTL_QSCNTEN_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_QSCNTEN_SHIFT 14 -#define DDR_PHY_DX8SL0DQSCTL_QSCNTEN_MASK 0x00004000U - -/*Unused DQ I/O Mode*/ -#undef DDR_PHY_DX8SL0DQSCTL_UDQIOM_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_UDQIOM_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_UDQIOM_MASK -#define DDR_PHY_DX8SL0DQSCTL_UDQIOM_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_UDQIOM_SHIFT 13 -#define DDR_PHY_DX8SL0DQSCTL_UDQIOM_MASK 0x00002000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10_MASK -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10_SHIFT 10 -#define DDR_PHY_DX8SL0DQSCTL_RESERVED_12_10_MASK 0x00001C00U - -/*Data Slew Rate*/ -#undef DDR_PHY_DX8SL0DQSCTL_DXSR_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_DXSR_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_DXSR_MASK -#define DDR_PHY_DX8SL0DQSCTL_DXSR_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_DXSR_SHIFT 8 -#define DDR_PHY_DX8SL0DQSCTL_DXSR_MASK 0x00000300U - -/*DQS_N Resistor*/ -#undef DDR_PHY_DX8SL0DQSCTL_DQSNRES_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_DQSNRES_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_DQSNRES_MASK -#define DDR_PHY_DX8SL0DQSCTL_DQSNRES_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_DQSNRES_SHIFT 4 -#define DDR_PHY_DX8SL0DQSCTL_DQSNRES_MASK 0x000000F0U - -/*DQS Resistor*/ -#undef DDR_PHY_DX8SL0DQSCTL_DQSRES_DEFVAL -#undef DDR_PHY_DX8SL0DQSCTL_DQSRES_SHIFT -#undef DDR_PHY_DX8SL0DQSCTL_DQSRES_MASK -#define DDR_PHY_DX8SL0DQSCTL_DQSRES_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL0DQSCTL_DQSRES_SHIFT 0 -#define DDR_PHY_DX8SL0DQSCTL_DQSRES_MASK 0x0000000FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24_MASK -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24_SHIFT 24 -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_31_24_MASK 0xFF000000U - -/*Configurable Read Data Enable*/ -#undef DDR_PHY_DX8SL0DXCTL2_CRDEN_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_CRDEN_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_CRDEN_MASK -#define DDR_PHY_DX8SL0DXCTL2_CRDEN_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_CRDEN_SHIFT 23 -#define DDR_PHY_DX8SL0DXCTL2_CRDEN_MASK 0x00800000U - -/*OX Extension during Post-amble*/ -#undef DDR_PHY_DX8SL0DXCTL2_POSOEX_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_POSOEX_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_POSOEX_MASK -#define DDR_PHY_DX8SL0DXCTL2_POSOEX_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_POSOEX_SHIFT 20 -#define DDR_PHY_DX8SL0DXCTL2_POSOEX_MASK 0x00700000U - -/*OE Extension during Pre-amble*/ -#undef DDR_PHY_DX8SL0DXCTL2_PREOEX_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_PREOEX_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_PREOEX_MASK -#define DDR_PHY_DX8SL0DXCTL2_PREOEX_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_PREOEX_SHIFT 18 -#define DDR_PHY_DX8SL0DXCTL2_PREOEX_MASK 0x000C0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_17_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_17_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_17_MASK -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_17_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_17_SHIFT 17 -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_17_MASK 0x00020000U - -/*I/O Assisted Gate Select*/ -#undef DDR_PHY_DX8SL0DXCTL2_IOAG_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_IOAG_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_IOAG_MASK -#define DDR_PHY_DX8SL0DXCTL2_IOAG_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_IOAG_SHIFT 16 -#define DDR_PHY_DX8SL0DXCTL2_IOAG_MASK 0x00010000U - -/*I/O Loopback Select*/ -#undef DDR_PHY_DX8SL0DXCTL2_IOLB_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_IOLB_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_IOLB_MASK -#define DDR_PHY_DX8SL0DXCTL2_IOLB_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_IOLB_SHIFT 15 -#define DDR_PHY_DX8SL0DXCTL2_IOLB_MASK 0x00008000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13_MASK -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13_SHIFT 13 -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_14_13_MASK 0x00006000U - -/*Low Power Wakeup Threshold*/ -#undef DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH_MASK -#define DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH_SHIFT 9 -#define DDR_PHY_DX8SL0DXCTL2_LPWAKEUP_THRSH_MASK 0x00001E00U - -/*Read Data Bus Inversion Enable*/ -#undef DDR_PHY_DX8SL0DXCTL2_RDBI_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_RDBI_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_RDBI_MASK -#define DDR_PHY_DX8SL0DXCTL2_RDBI_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_RDBI_SHIFT 8 -#define DDR_PHY_DX8SL0DXCTL2_RDBI_MASK 0x00000100U - -/*Write Data Bus Inversion Enable*/ -#undef DDR_PHY_DX8SL0DXCTL2_WDBI_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_WDBI_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_WDBI_MASK -#define DDR_PHY_DX8SL0DXCTL2_WDBI_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_WDBI_SHIFT 7 -#define DDR_PHY_DX8SL0DXCTL2_WDBI_MASK 0x00000080U - -/*PUB Read FIFO Bypass*/ -#undef DDR_PHY_DX8SL0DXCTL2_PRFBYP_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_PRFBYP_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_PRFBYP_MASK -#define DDR_PHY_DX8SL0DXCTL2_PRFBYP_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_PRFBYP_SHIFT 6 -#define DDR_PHY_DX8SL0DXCTL2_PRFBYP_MASK 0x00000040U - -/*DATX8 Receive FIFO Read Mode*/ -#undef DDR_PHY_DX8SL0DXCTL2_RDMODE_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_RDMODE_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_RDMODE_MASK -#define DDR_PHY_DX8SL0DXCTL2_RDMODE_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_RDMODE_SHIFT 4 -#define DDR_PHY_DX8SL0DXCTL2_RDMODE_MASK 0x00000030U - -/*Disables the Read FIFO Reset*/ -#undef DDR_PHY_DX8SL0DXCTL2_DISRST_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_DISRST_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_DISRST_MASK -#define DDR_PHY_DX8SL0DXCTL2_DISRST_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_DISRST_SHIFT 3 -#define DDR_PHY_DX8SL0DXCTL2_DISRST_MASK 0x00000008U - -/*Read DQS Gate I/O Loopback*/ -#undef DDR_PHY_DX8SL0DXCTL2_DQSGLB_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_DQSGLB_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_DQSGLB_MASK -#define DDR_PHY_DX8SL0DXCTL2_DQSGLB_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_DQSGLB_SHIFT 1 -#define DDR_PHY_DX8SL0DXCTL2_DQSGLB_MASK 0x00000006U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_0_DEFVAL -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_0_SHIFT -#undef DDR_PHY_DX8SL0DXCTL2_RESERVED_0_MASK -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_0_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_0_SHIFT 0 -#define DDR_PHY_DX8SL0DXCTL2_RESERVED_0_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL0IOCR_RESERVED_31_DEFVAL -#undef DDR_PHY_DX8SL0IOCR_RESERVED_31_SHIFT -#undef DDR_PHY_DX8SL0IOCR_RESERVED_31_MASK -#define DDR_PHY_DX8SL0IOCR_RESERVED_31_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL0IOCR_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX8SL0IOCR_RESERVED_31_MASK 0x80000000U - -/*PVREF_DAC REFSEL range select*/ -#undef DDR_PHY_DX8SL0IOCR_DXDACRANGE_DEFVAL -#undef DDR_PHY_DX8SL0IOCR_DXDACRANGE_SHIFT -#undef DDR_PHY_DX8SL0IOCR_DXDACRANGE_MASK -#define DDR_PHY_DX8SL0IOCR_DXDACRANGE_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL0IOCR_DXDACRANGE_SHIFT 28 -#define DDR_PHY_DX8SL0IOCR_DXDACRANGE_MASK 0x70000000U - -/*IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring*/ -#undef DDR_PHY_DX8SL0IOCR_DXVREFIOM_DEFVAL -#undef DDR_PHY_DX8SL0IOCR_DXVREFIOM_SHIFT -#undef DDR_PHY_DX8SL0IOCR_DXVREFIOM_MASK -#define DDR_PHY_DX8SL0IOCR_DXVREFIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL0IOCR_DXVREFIOM_SHIFT 25 -#define DDR_PHY_DX8SL0IOCR_DXVREFIOM_MASK 0x0E000000U - -/*DX IO Mode*/ -#undef DDR_PHY_DX8SL0IOCR_DXIOM_DEFVAL -#undef DDR_PHY_DX8SL0IOCR_DXIOM_SHIFT -#undef DDR_PHY_DX8SL0IOCR_DXIOM_MASK -#define DDR_PHY_DX8SL0IOCR_DXIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL0IOCR_DXIOM_SHIFT 22 -#define DDR_PHY_DX8SL0IOCR_DXIOM_MASK 0x01C00000U - -/*DX IO Transmitter Mode*/ -#undef DDR_PHY_DX8SL0IOCR_DXTXM_DEFVAL -#undef DDR_PHY_DX8SL0IOCR_DXTXM_SHIFT -#undef DDR_PHY_DX8SL0IOCR_DXTXM_MASK -#define DDR_PHY_DX8SL0IOCR_DXTXM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL0IOCR_DXTXM_SHIFT 11 -#define DDR_PHY_DX8SL0IOCR_DXTXM_MASK 0x003FF800U - -/*DX IO Receiver Mode*/ -#undef DDR_PHY_DX8SL0IOCR_DXRXM_DEFVAL -#undef DDR_PHY_DX8SL0IOCR_DXRXM_SHIFT -#undef DDR_PHY_DX8SL0IOCR_DXRXM_MASK -#define DDR_PHY_DX8SL0IOCR_DXRXM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL0IOCR_DXRXM_SHIFT 0 -#define DDR_PHY_DX8SL0IOCR_DXRXM_MASK 0x000007FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL1OSC_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX8SL1OSC_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX8SL1OSC_RESERVED_31_30_MASK -#define DDR_PHY_DX8SL1OSC_RESERVED_31_30_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX8SL1OSC_RESERVED_31_30_MASK 0xC0000000U - -/*Enable Clock Gating for DX ddr_clk*/ -#undef DDR_PHY_DX8SL1OSC_GATEDXRDCLK_DEFVAL -#undef DDR_PHY_DX8SL1OSC_GATEDXRDCLK_SHIFT -#undef DDR_PHY_DX8SL1OSC_GATEDXRDCLK_MASK -#define DDR_PHY_DX8SL1OSC_GATEDXRDCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_GATEDXRDCLK_SHIFT 28 -#define DDR_PHY_DX8SL1OSC_GATEDXRDCLK_MASK 0x30000000U - -/*Enable Clock Gating for DX ctl_rd_clk*/ -#undef DDR_PHY_DX8SL1OSC_GATEDXDDRCLK_DEFVAL -#undef DDR_PHY_DX8SL1OSC_GATEDXDDRCLK_SHIFT -#undef DDR_PHY_DX8SL1OSC_GATEDXDDRCLK_MASK -#define DDR_PHY_DX8SL1OSC_GATEDXDDRCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_GATEDXDDRCLK_SHIFT 26 -#define DDR_PHY_DX8SL1OSC_GATEDXDDRCLK_MASK 0x0C000000U - -/*Enable Clock Gating for DX ctl_clk*/ -#undef DDR_PHY_DX8SL1OSC_GATEDXCTLCLK_DEFVAL -#undef DDR_PHY_DX8SL1OSC_GATEDXCTLCLK_SHIFT -#undef DDR_PHY_DX8SL1OSC_GATEDXCTLCLK_MASK -#define DDR_PHY_DX8SL1OSC_GATEDXCTLCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_GATEDXCTLCLK_SHIFT 24 -#define DDR_PHY_DX8SL1OSC_GATEDXCTLCLK_MASK 0x03000000U - -/*Selects the level to which clocks will be stalled when clock gating is enabled.*/ -#undef DDR_PHY_DX8SL1OSC_CLKLEVEL_DEFVAL -#undef DDR_PHY_DX8SL1OSC_CLKLEVEL_SHIFT -#undef DDR_PHY_DX8SL1OSC_CLKLEVEL_MASK -#define DDR_PHY_DX8SL1OSC_CLKLEVEL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_CLKLEVEL_SHIFT 22 -#define DDR_PHY_DX8SL1OSC_CLKLEVEL_MASK 0x00C00000U - -/*Loopback Mode*/ -#undef DDR_PHY_DX8SL1OSC_LBMODE_DEFVAL -#undef DDR_PHY_DX8SL1OSC_LBMODE_SHIFT -#undef DDR_PHY_DX8SL1OSC_LBMODE_MASK -#define DDR_PHY_DX8SL1OSC_LBMODE_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_LBMODE_SHIFT 21 -#define DDR_PHY_DX8SL1OSC_LBMODE_MASK 0x00200000U - -/*Load GSDQS LCDL with 2x the calibrated GSDQSPRD value*/ -#undef DDR_PHY_DX8SL1OSC_LBGSDQS_DEFVAL -#undef DDR_PHY_DX8SL1OSC_LBGSDQS_SHIFT -#undef DDR_PHY_DX8SL1OSC_LBGSDQS_MASK -#define DDR_PHY_DX8SL1OSC_LBGSDQS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_LBGSDQS_SHIFT 20 -#define DDR_PHY_DX8SL1OSC_LBGSDQS_MASK 0x00100000U - -/*Loopback DQS Gating*/ -#undef DDR_PHY_DX8SL1OSC_LBGDQS_DEFVAL -#undef DDR_PHY_DX8SL1OSC_LBGDQS_SHIFT -#undef DDR_PHY_DX8SL1OSC_LBGDQS_MASK -#define DDR_PHY_DX8SL1OSC_LBGDQS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_LBGDQS_SHIFT 18 -#define DDR_PHY_DX8SL1OSC_LBGDQS_MASK 0x000C0000U - -/*Loopback DQS Shift*/ -#undef DDR_PHY_DX8SL1OSC_LBDQSS_DEFVAL -#undef DDR_PHY_DX8SL1OSC_LBDQSS_SHIFT -#undef DDR_PHY_DX8SL1OSC_LBDQSS_MASK -#define DDR_PHY_DX8SL1OSC_LBDQSS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_LBDQSS_SHIFT 17 -#define DDR_PHY_DX8SL1OSC_LBDQSS_MASK 0x00020000U - -/*PHY High-Speed Reset*/ -#undef DDR_PHY_DX8SL1OSC_PHYHRST_DEFVAL -#undef DDR_PHY_DX8SL1OSC_PHYHRST_SHIFT -#undef DDR_PHY_DX8SL1OSC_PHYHRST_MASK -#define DDR_PHY_DX8SL1OSC_PHYHRST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_PHYHRST_SHIFT 16 -#define DDR_PHY_DX8SL1OSC_PHYHRST_MASK 0x00010000U - -/*PHY FIFO Reset*/ -#undef DDR_PHY_DX8SL1OSC_PHYFRST_DEFVAL -#undef DDR_PHY_DX8SL1OSC_PHYFRST_SHIFT -#undef DDR_PHY_DX8SL1OSC_PHYFRST_MASK -#define DDR_PHY_DX8SL1OSC_PHYFRST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_PHYFRST_SHIFT 15 -#define DDR_PHY_DX8SL1OSC_PHYFRST_MASK 0x00008000U - -/*Delay Line Test Start*/ -#undef DDR_PHY_DX8SL1OSC_DLTST_DEFVAL -#undef DDR_PHY_DX8SL1OSC_DLTST_SHIFT -#undef DDR_PHY_DX8SL1OSC_DLTST_MASK -#define DDR_PHY_DX8SL1OSC_DLTST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_DLTST_SHIFT 14 -#define DDR_PHY_DX8SL1OSC_DLTST_MASK 0x00004000U - -/*Delay Line Test Mode*/ -#undef DDR_PHY_DX8SL1OSC_DLTMODE_DEFVAL -#undef DDR_PHY_DX8SL1OSC_DLTMODE_SHIFT -#undef DDR_PHY_DX8SL1OSC_DLTMODE_MASK -#define DDR_PHY_DX8SL1OSC_DLTMODE_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_DLTMODE_SHIFT 13 -#define DDR_PHY_DX8SL1OSC_DLTMODE_MASK 0x00002000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8SL1OSC_RESERVED_12_11_DEFVAL -#undef DDR_PHY_DX8SL1OSC_RESERVED_12_11_SHIFT -#undef DDR_PHY_DX8SL1OSC_RESERVED_12_11_MASK -#define DDR_PHY_DX8SL1OSC_RESERVED_12_11_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_RESERVED_12_11_SHIFT 11 -#define DDR_PHY_DX8SL1OSC_RESERVED_12_11_MASK 0x00001800U - -/*Oscillator Mode Write-Data Delay Line Select*/ -#undef DDR_PHY_DX8SL1OSC_OSCWDDL_DEFVAL -#undef DDR_PHY_DX8SL1OSC_OSCWDDL_SHIFT -#undef DDR_PHY_DX8SL1OSC_OSCWDDL_MASK -#define DDR_PHY_DX8SL1OSC_OSCWDDL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_OSCWDDL_SHIFT 9 -#define DDR_PHY_DX8SL1OSC_OSCWDDL_MASK 0x00000600U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8SL1OSC_RESERVED_8_7_DEFVAL -#undef DDR_PHY_DX8SL1OSC_RESERVED_8_7_SHIFT -#undef DDR_PHY_DX8SL1OSC_RESERVED_8_7_MASK -#define DDR_PHY_DX8SL1OSC_RESERVED_8_7_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_RESERVED_8_7_SHIFT 7 -#define DDR_PHY_DX8SL1OSC_RESERVED_8_7_MASK 0x00000180U - -/*Oscillator Mode Write-Leveling Delay Line Select*/ -#undef DDR_PHY_DX8SL1OSC_OSCWDL_DEFVAL -#undef DDR_PHY_DX8SL1OSC_OSCWDL_SHIFT -#undef DDR_PHY_DX8SL1OSC_OSCWDL_MASK -#define DDR_PHY_DX8SL1OSC_OSCWDL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_OSCWDL_SHIFT 5 -#define DDR_PHY_DX8SL1OSC_OSCWDL_MASK 0x00000060U - -/*Oscillator Mode Division*/ -#undef DDR_PHY_DX8SL1OSC_OSCDIV_DEFVAL -#undef DDR_PHY_DX8SL1OSC_OSCDIV_SHIFT -#undef DDR_PHY_DX8SL1OSC_OSCDIV_MASK -#define DDR_PHY_DX8SL1OSC_OSCDIV_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_OSCDIV_SHIFT 1 -#define DDR_PHY_DX8SL1OSC_OSCDIV_MASK 0x0000001EU - -/*Oscillator Enable*/ -#undef DDR_PHY_DX8SL1OSC_OSCEN_DEFVAL -#undef DDR_PHY_DX8SL1OSC_OSCEN_SHIFT -#undef DDR_PHY_DX8SL1OSC_OSCEN_MASK -#define DDR_PHY_DX8SL1OSC_OSCEN_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL1OSC_OSCEN_SHIFT 0 -#define DDR_PHY_DX8SL1OSC_OSCEN_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25_MASK -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_31_25_MASK 0xFE000000U - -/*Read Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SL1DQSCTL_RRRMODE_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_RRRMODE_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_RRRMODE_MASK -#define DDR_PHY_DX8SL1DQSCTL_RRRMODE_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_RRRMODE_SHIFT 24 -#define DDR_PHY_DX8SL1DQSCTL_RRRMODE_MASK 0x01000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22_MASK -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_23_22_MASK 0x00C00000U - -/*Write Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SL1DQSCTL_WRRMODE_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_WRRMODE_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_WRRMODE_MASK -#define DDR_PHY_DX8SL1DQSCTL_WRRMODE_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_WRRMODE_SHIFT 21 -#define DDR_PHY_DX8SL1DQSCTL_WRRMODE_MASK 0x00200000U - -/*DQS Gate Extension*/ -#undef DDR_PHY_DX8SL1DQSCTL_DQSGX_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_DQSGX_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_DQSGX_MASK -#define DDR_PHY_DX8SL1DQSCTL_DQSGX_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_DQSGX_SHIFT 19 -#define DDR_PHY_DX8SL1DQSCTL_DQSGX_MASK 0x00180000U - -/*Low Power PLL Power Down*/ -#undef DDR_PHY_DX8SL1DQSCTL_LPPLLPD_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_LPPLLPD_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_LPPLLPD_MASK -#define DDR_PHY_DX8SL1DQSCTL_LPPLLPD_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_LPPLLPD_SHIFT 18 -#define DDR_PHY_DX8SL1DQSCTL_LPPLLPD_MASK 0x00040000U - -/*Low Power I/O Power Down*/ -#undef DDR_PHY_DX8SL1DQSCTL_LPIOPD_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_LPIOPD_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_LPIOPD_MASK -#define DDR_PHY_DX8SL1DQSCTL_LPIOPD_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_LPIOPD_SHIFT 17 -#define DDR_PHY_DX8SL1DQSCTL_LPIOPD_MASK 0x00020000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15_MASK -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15_SHIFT 15 -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_16_15_MASK 0x00018000U - -/*QS Counter Enable*/ -#undef DDR_PHY_DX8SL1DQSCTL_QSCNTEN_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_QSCNTEN_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_QSCNTEN_MASK -#define DDR_PHY_DX8SL1DQSCTL_QSCNTEN_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_QSCNTEN_SHIFT 14 -#define DDR_PHY_DX8SL1DQSCTL_QSCNTEN_MASK 0x00004000U - -/*Unused DQ I/O Mode*/ -#undef DDR_PHY_DX8SL1DQSCTL_UDQIOM_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_UDQIOM_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_UDQIOM_MASK -#define DDR_PHY_DX8SL1DQSCTL_UDQIOM_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_UDQIOM_SHIFT 13 -#define DDR_PHY_DX8SL1DQSCTL_UDQIOM_MASK 0x00002000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10_MASK -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10_SHIFT 10 -#define DDR_PHY_DX8SL1DQSCTL_RESERVED_12_10_MASK 0x00001C00U - -/*Data Slew Rate*/ -#undef DDR_PHY_DX8SL1DQSCTL_DXSR_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_DXSR_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_DXSR_MASK -#define DDR_PHY_DX8SL1DQSCTL_DXSR_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_DXSR_SHIFT 8 -#define DDR_PHY_DX8SL1DQSCTL_DXSR_MASK 0x00000300U - -/*DQS_N Resistor*/ -#undef DDR_PHY_DX8SL1DQSCTL_DQSNRES_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_DQSNRES_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_DQSNRES_MASK -#define DDR_PHY_DX8SL1DQSCTL_DQSNRES_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_DQSNRES_SHIFT 4 -#define DDR_PHY_DX8SL1DQSCTL_DQSNRES_MASK 0x000000F0U - -/*DQS Resistor*/ -#undef DDR_PHY_DX8SL1DQSCTL_DQSRES_DEFVAL -#undef DDR_PHY_DX8SL1DQSCTL_DQSRES_SHIFT -#undef DDR_PHY_DX8SL1DQSCTL_DQSRES_MASK -#define DDR_PHY_DX8SL1DQSCTL_DQSRES_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL1DQSCTL_DQSRES_SHIFT 0 -#define DDR_PHY_DX8SL1DQSCTL_DQSRES_MASK 0x0000000FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24_MASK -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24_SHIFT 24 -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_31_24_MASK 0xFF000000U - -/*Configurable Read Data Enable*/ -#undef DDR_PHY_DX8SL1DXCTL2_CRDEN_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_CRDEN_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_CRDEN_MASK -#define DDR_PHY_DX8SL1DXCTL2_CRDEN_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_CRDEN_SHIFT 23 -#define DDR_PHY_DX8SL1DXCTL2_CRDEN_MASK 0x00800000U - -/*OX Extension during Post-amble*/ -#undef DDR_PHY_DX8SL1DXCTL2_POSOEX_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_POSOEX_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_POSOEX_MASK -#define DDR_PHY_DX8SL1DXCTL2_POSOEX_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_POSOEX_SHIFT 20 -#define DDR_PHY_DX8SL1DXCTL2_POSOEX_MASK 0x00700000U - -/*OE Extension during Pre-amble*/ -#undef DDR_PHY_DX8SL1DXCTL2_PREOEX_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_PREOEX_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_PREOEX_MASK -#define DDR_PHY_DX8SL1DXCTL2_PREOEX_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_PREOEX_SHIFT 18 -#define DDR_PHY_DX8SL1DXCTL2_PREOEX_MASK 0x000C0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_17_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_17_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_17_MASK -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_17_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_17_SHIFT 17 -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_17_MASK 0x00020000U - -/*I/O Assisted Gate Select*/ -#undef DDR_PHY_DX8SL1DXCTL2_IOAG_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_IOAG_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_IOAG_MASK -#define DDR_PHY_DX8SL1DXCTL2_IOAG_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_IOAG_SHIFT 16 -#define DDR_PHY_DX8SL1DXCTL2_IOAG_MASK 0x00010000U - -/*I/O Loopback Select*/ -#undef DDR_PHY_DX8SL1DXCTL2_IOLB_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_IOLB_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_IOLB_MASK -#define DDR_PHY_DX8SL1DXCTL2_IOLB_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_IOLB_SHIFT 15 -#define DDR_PHY_DX8SL1DXCTL2_IOLB_MASK 0x00008000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13_MASK -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13_SHIFT 13 -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_14_13_MASK 0x00006000U - -/*Low Power Wakeup Threshold*/ -#undef DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH_MASK -#define DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH_SHIFT 9 -#define DDR_PHY_DX8SL1DXCTL2_LPWAKEUP_THRSH_MASK 0x00001E00U - -/*Read Data Bus Inversion Enable*/ -#undef DDR_PHY_DX8SL1DXCTL2_RDBI_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_RDBI_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_RDBI_MASK -#define DDR_PHY_DX8SL1DXCTL2_RDBI_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_RDBI_SHIFT 8 -#define DDR_PHY_DX8SL1DXCTL2_RDBI_MASK 0x00000100U - -/*Write Data Bus Inversion Enable*/ -#undef DDR_PHY_DX8SL1DXCTL2_WDBI_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_WDBI_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_WDBI_MASK -#define DDR_PHY_DX8SL1DXCTL2_WDBI_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_WDBI_SHIFT 7 -#define DDR_PHY_DX8SL1DXCTL2_WDBI_MASK 0x00000080U - -/*PUB Read FIFO Bypass*/ -#undef DDR_PHY_DX8SL1DXCTL2_PRFBYP_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_PRFBYP_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_PRFBYP_MASK -#define DDR_PHY_DX8SL1DXCTL2_PRFBYP_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_PRFBYP_SHIFT 6 -#define DDR_PHY_DX8SL1DXCTL2_PRFBYP_MASK 0x00000040U - -/*DATX8 Receive FIFO Read Mode*/ -#undef DDR_PHY_DX8SL1DXCTL2_RDMODE_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_RDMODE_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_RDMODE_MASK -#define DDR_PHY_DX8SL1DXCTL2_RDMODE_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_RDMODE_SHIFT 4 -#define DDR_PHY_DX8SL1DXCTL2_RDMODE_MASK 0x00000030U - -/*Disables the Read FIFO Reset*/ -#undef DDR_PHY_DX8SL1DXCTL2_DISRST_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_DISRST_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_DISRST_MASK -#define DDR_PHY_DX8SL1DXCTL2_DISRST_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_DISRST_SHIFT 3 -#define DDR_PHY_DX8SL1DXCTL2_DISRST_MASK 0x00000008U - -/*Read DQS Gate I/O Loopback*/ -#undef DDR_PHY_DX8SL1DXCTL2_DQSGLB_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_DQSGLB_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_DQSGLB_MASK -#define DDR_PHY_DX8SL1DXCTL2_DQSGLB_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_DQSGLB_SHIFT 1 -#define DDR_PHY_DX8SL1DXCTL2_DQSGLB_MASK 0x00000006U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_0_DEFVAL -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_0_SHIFT -#undef DDR_PHY_DX8SL1DXCTL2_RESERVED_0_MASK -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_0_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_0_SHIFT 0 -#define DDR_PHY_DX8SL1DXCTL2_RESERVED_0_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL1IOCR_RESERVED_31_DEFVAL -#undef DDR_PHY_DX8SL1IOCR_RESERVED_31_SHIFT -#undef DDR_PHY_DX8SL1IOCR_RESERVED_31_MASK -#define DDR_PHY_DX8SL1IOCR_RESERVED_31_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL1IOCR_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX8SL1IOCR_RESERVED_31_MASK 0x80000000U - -/*PVREF_DAC REFSEL range select*/ -#undef DDR_PHY_DX8SL1IOCR_DXDACRANGE_DEFVAL -#undef DDR_PHY_DX8SL1IOCR_DXDACRANGE_SHIFT -#undef DDR_PHY_DX8SL1IOCR_DXDACRANGE_MASK -#define DDR_PHY_DX8SL1IOCR_DXDACRANGE_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL1IOCR_DXDACRANGE_SHIFT 28 -#define DDR_PHY_DX8SL1IOCR_DXDACRANGE_MASK 0x70000000U - -/*IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring*/ -#undef DDR_PHY_DX8SL1IOCR_DXVREFIOM_DEFVAL -#undef DDR_PHY_DX8SL1IOCR_DXVREFIOM_SHIFT -#undef DDR_PHY_DX8SL1IOCR_DXVREFIOM_MASK -#define DDR_PHY_DX8SL1IOCR_DXVREFIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL1IOCR_DXVREFIOM_SHIFT 25 -#define DDR_PHY_DX8SL1IOCR_DXVREFIOM_MASK 0x0E000000U - -/*DX IO Mode*/ -#undef DDR_PHY_DX8SL1IOCR_DXIOM_DEFVAL -#undef DDR_PHY_DX8SL1IOCR_DXIOM_SHIFT -#undef DDR_PHY_DX8SL1IOCR_DXIOM_MASK -#define DDR_PHY_DX8SL1IOCR_DXIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL1IOCR_DXIOM_SHIFT 22 -#define DDR_PHY_DX8SL1IOCR_DXIOM_MASK 0x01C00000U - -/*DX IO Transmitter Mode*/ -#undef DDR_PHY_DX8SL1IOCR_DXTXM_DEFVAL -#undef DDR_PHY_DX8SL1IOCR_DXTXM_SHIFT -#undef DDR_PHY_DX8SL1IOCR_DXTXM_MASK -#define DDR_PHY_DX8SL1IOCR_DXTXM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL1IOCR_DXTXM_SHIFT 11 -#define DDR_PHY_DX8SL1IOCR_DXTXM_MASK 0x003FF800U - -/*DX IO Receiver Mode*/ -#undef DDR_PHY_DX8SL1IOCR_DXRXM_DEFVAL -#undef DDR_PHY_DX8SL1IOCR_DXRXM_SHIFT -#undef DDR_PHY_DX8SL1IOCR_DXRXM_MASK -#define DDR_PHY_DX8SL1IOCR_DXRXM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL1IOCR_DXRXM_SHIFT 0 -#define DDR_PHY_DX8SL1IOCR_DXRXM_MASK 0x000007FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL2OSC_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX8SL2OSC_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX8SL2OSC_RESERVED_31_30_MASK -#define DDR_PHY_DX8SL2OSC_RESERVED_31_30_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX8SL2OSC_RESERVED_31_30_MASK 0xC0000000U - -/*Enable Clock Gating for DX ddr_clk*/ -#undef DDR_PHY_DX8SL2OSC_GATEDXRDCLK_DEFVAL -#undef DDR_PHY_DX8SL2OSC_GATEDXRDCLK_SHIFT -#undef DDR_PHY_DX8SL2OSC_GATEDXRDCLK_MASK -#define DDR_PHY_DX8SL2OSC_GATEDXRDCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_GATEDXRDCLK_SHIFT 28 -#define DDR_PHY_DX8SL2OSC_GATEDXRDCLK_MASK 0x30000000U - -/*Enable Clock Gating for DX ctl_rd_clk*/ -#undef DDR_PHY_DX8SL2OSC_GATEDXDDRCLK_DEFVAL -#undef DDR_PHY_DX8SL2OSC_GATEDXDDRCLK_SHIFT -#undef DDR_PHY_DX8SL2OSC_GATEDXDDRCLK_MASK -#define DDR_PHY_DX8SL2OSC_GATEDXDDRCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_GATEDXDDRCLK_SHIFT 26 -#define DDR_PHY_DX8SL2OSC_GATEDXDDRCLK_MASK 0x0C000000U - -/*Enable Clock Gating for DX ctl_clk*/ -#undef DDR_PHY_DX8SL2OSC_GATEDXCTLCLK_DEFVAL -#undef DDR_PHY_DX8SL2OSC_GATEDXCTLCLK_SHIFT -#undef DDR_PHY_DX8SL2OSC_GATEDXCTLCLK_MASK -#define DDR_PHY_DX8SL2OSC_GATEDXCTLCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_GATEDXCTLCLK_SHIFT 24 -#define DDR_PHY_DX8SL2OSC_GATEDXCTLCLK_MASK 0x03000000U - -/*Selects the level to which clocks will be stalled when clock gating is enabled.*/ -#undef DDR_PHY_DX8SL2OSC_CLKLEVEL_DEFVAL -#undef DDR_PHY_DX8SL2OSC_CLKLEVEL_SHIFT -#undef DDR_PHY_DX8SL2OSC_CLKLEVEL_MASK -#define DDR_PHY_DX8SL2OSC_CLKLEVEL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_CLKLEVEL_SHIFT 22 -#define DDR_PHY_DX8SL2OSC_CLKLEVEL_MASK 0x00C00000U - -/*Loopback Mode*/ -#undef DDR_PHY_DX8SL2OSC_LBMODE_DEFVAL -#undef DDR_PHY_DX8SL2OSC_LBMODE_SHIFT -#undef DDR_PHY_DX8SL2OSC_LBMODE_MASK -#define DDR_PHY_DX8SL2OSC_LBMODE_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_LBMODE_SHIFT 21 -#define DDR_PHY_DX8SL2OSC_LBMODE_MASK 0x00200000U - -/*Load GSDQS LCDL with 2x the calibrated GSDQSPRD value*/ -#undef DDR_PHY_DX8SL2OSC_LBGSDQS_DEFVAL -#undef DDR_PHY_DX8SL2OSC_LBGSDQS_SHIFT -#undef DDR_PHY_DX8SL2OSC_LBGSDQS_MASK -#define DDR_PHY_DX8SL2OSC_LBGSDQS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_LBGSDQS_SHIFT 20 -#define DDR_PHY_DX8SL2OSC_LBGSDQS_MASK 0x00100000U - -/*Loopback DQS Gating*/ -#undef DDR_PHY_DX8SL2OSC_LBGDQS_DEFVAL -#undef DDR_PHY_DX8SL2OSC_LBGDQS_SHIFT -#undef DDR_PHY_DX8SL2OSC_LBGDQS_MASK -#define DDR_PHY_DX8SL2OSC_LBGDQS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_LBGDQS_SHIFT 18 -#define DDR_PHY_DX8SL2OSC_LBGDQS_MASK 0x000C0000U - -/*Loopback DQS Shift*/ -#undef DDR_PHY_DX8SL2OSC_LBDQSS_DEFVAL -#undef DDR_PHY_DX8SL2OSC_LBDQSS_SHIFT -#undef DDR_PHY_DX8SL2OSC_LBDQSS_MASK -#define DDR_PHY_DX8SL2OSC_LBDQSS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_LBDQSS_SHIFT 17 -#define DDR_PHY_DX8SL2OSC_LBDQSS_MASK 0x00020000U - -/*PHY High-Speed Reset*/ -#undef DDR_PHY_DX8SL2OSC_PHYHRST_DEFVAL -#undef DDR_PHY_DX8SL2OSC_PHYHRST_SHIFT -#undef DDR_PHY_DX8SL2OSC_PHYHRST_MASK -#define DDR_PHY_DX8SL2OSC_PHYHRST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_PHYHRST_SHIFT 16 -#define DDR_PHY_DX8SL2OSC_PHYHRST_MASK 0x00010000U - -/*PHY FIFO Reset*/ -#undef DDR_PHY_DX8SL2OSC_PHYFRST_DEFVAL -#undef DDR_PHY_DX8SL2OSC_PHYFRST_SHIFT -#undef DDR_PHY_DX8SL2OSC_PHYFRST_MASK -#define DDR_PHY_DX8SL2OSC_PHYFRST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_PHYFRST_SHIFT 15 -#define DDR_PHY_DX8SL2OSC_PHYFRST_MASK 0x00008000U - -/*Delay Line Test Start*/ -#undef DDR_PHY_DX8SL2OSC_DLTST_DEFVAL -#undef DDR_PHY_DX8SL2OSC_DLTST_SHIFT -#undef DDR_PHY_DX8SL2OSC_DLTST_MASK -#define DDR_PHY_DX8SL2OSC_DLTST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_DLTST_SHIFT 14 -#define DDR_PHY_DX8SL2OSC_DLTST_MASK 0x00004000U - -/*Delay Line Test Mode*/ -#undef DDR_PHY_DX8SL2OSC_DLTMODE_DEFVAL -#undef DDR_PHY_DX8SL2OSC_DLTMODE_SHIFT -#undef DDR_PHY_DX8SL2OSC_DLTMODE_MASK -#define DDR_PHY_DX8SL2OSC_DLTMODE_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_DLTMODE_SHIFT 13 -#define DDR_PHY_DX8SL2OSC_DLTMODE_MASK 0x00002000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8SL2OSC_RESERVED_12_11_DEFVAL -#undef DDR_PHY_DX8SL2OSC_RESERVED_12_11_SHIFT -#undef DDR_PHY_DX8SL2OSC_RESERVED_12_11_MASK -#define DDR_PHY_DX8SL2OSC_RESERVED_12_11_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_RESERVED_12_11_SHIFT 11 -#define DDR_PHY_DX8SL2OSC_RESERVED_12_11_MASK 0x00001800U - -/*Oscillator Mode Write-Data Delay Line Select*/ -#undef DDR_PHY_DX8SL2OSC_OSCWDDL_DEFVAL -#undef DDR_PHY_DX8SL2OSC_OSCWDDL_SHIFT -#undef DDR_PHY_DX8SL2OSC_OSCWDDL_MASK -#define DDR_PHY_DX8SL2OSC_OSCWDDL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_OSCWDDL_SHIFT 9 -#define DDR_PHY_DX8SL2OSC_OSCWDDL_MASK 0x00000600U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8SL2OSC_RESERVED_8_7_DEFVAL -#undef DDR_PHY_DX8SL2OSC_RESERVED_8_7_SHIFT -#undef DDR_PHY_DX8SL2OSC_RESERVED_8_7_MASK -#define DDR_PHY_DX8SL2OSC_RESERVED_8_7_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_RESERVED_8_7_SHIFT 7 -#define DDR_PHY_DX8SL2OSC_RESERVED_8_7_MASK 0x00000180U - -/*Oscillator Mode Write-Leveling Delay Line Select*/ -#undef DDR_PHY_DX8SL2OSC_OSCWDL_DEFVAL -#undef DDR_PHY_DX8SL2OSC_OSCWDL_SHIFT -#undef DDR_PHY_DX8SL2OSC_OSCWDL_MASK -#define DDR_PHY_DX8SL2OSC_OSCWDL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_OSCWDL_SHIFT 5 -#define DDR_PHY_DX8SL2OSC_OSCWDL_MASK 0x00000060U - -/*Oscillator Mode Division*/ -#undef DDR_PHY_DX8SL2OSC_OSCDIV_DEFVAL -#undef DDR_PHY_DX8SL2OSC_OSCDIV_SHIFT -#undef DDR_PHY_DX8SL2OSC_OSCDIV_MASK -#define DDR_PHY_DX8SL2OSC_OSCDIV_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_OSCDIV_SHIFT 1 -#define DDR_PHY_DX8SL2OSC_OSCDIV_MASK 0x0000001EU - -/*Oscillator Enable*/ -#undef DDR_PHY_DX8SL2OSC_OSCEN_DEFVAL -#undef DDR_PHY_DX8SL2OSC_OSCEN_SHIFT -#undef DDR_PHY_DX8SL2OSC_OSCEN_MASK -#define DDR_PHY_DX8SL2OSC_OSCEN_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL2OSC_OSCEN_SHIFT 0 -#define DDR_PHY_DX8SL2OSC_OSCEN_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25_MASK -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_31_25_MASK 0xFE000000U - -/*Read Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SL2DQSCTL_RRRMODE_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_RRRMODE_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_RRRMODE_MASK -#define DDR_PHY_DX8SL2DQSCTL_RRRMODE_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_RRRMODE_SHIFT 24 -#define DDR_PHY_DX8SL2DQSCTL_RRRMODE_MASK 0x01000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22_MASK -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_23_22_MASK 0x00C00000U - -/*Write Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SL2DQSCTL_WRRMODE_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_WRRMODE_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_WRRMODE_MASK -#define DDR_PHY_DX8SL2DQSCTL_WRRMODE_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_WRRMODE_SHIFT 21 -#define DDR_PHY_DX8SL2DQSCTL_WRRMODE_MASK 0x00200000U - -/*DQS Gate Extension*/ -#undef DDR_PHY_DX8SL2DQSCTL_DQSGX_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_DQSGX_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_DQSGX_MASK -#define DDR_PHY_DX8SL2DQSCTL_DQSGX_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_DQSGX_SHIFT 19 -#define DDR_PHY_DX8SL2DQSCTL_DQSGX_MASK 0x00180000U - -/*Low Power PLL Power Down*/ -#undef DDR_PHY_DX8SL2DQSCTL_LPPLLPD_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_LPPLLPD_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_LPPLLPD_MASK -#define DDR_PHY_DX8SL2DQSCTL_LPPLLPD_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_LPPLLPD_SHIFT 18 -#define DDR_PHY_DX8SL2DQSCTL_LPPLLPD_MASK 0x00040000U - -/*Low Power I/O Power Down*/ -#undef DDR_PHY_DX8SL2DQSCTL_LPIOPD_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_LPIOPD_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_LPIOPD_MASK -#define DDR_PHY_DX8SL2DQSCTL_LPIOPD_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_LPIOPD_SHIFT 17 -#define DDR_PHY_DX8SL2DQSCTL_LPIOPD_MASK 0x00020000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15_MASK -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15_SHIFT 15 -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_16_15_MASK 0x00018000U - -/*QS Counter Enable*/ -#undef DDR_PHY_DX8SL2DQSCTL_QSCNTEN_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_QSCNTEN_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_QSCNTEN_MASK -#define DDR_PHY_DX8SL2DQSCTL_QSCNTEN_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_QSCNTEN_SHIFT 14 -#define DDR_PHY_DX8SL2DQSCTL_QSCNTEN_MASK 0x00004000U - -/*Unused DQ I/O Mode*/ -#undef DDR_PHY_DX8SL2DQSCTL_UDQIOM_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_UDQIOM_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_UDQIOM_MASK -#define DDR_PHY_DX8SL2DQSCTL_UDQIOM_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_UDQIOM_SHIFT 13 -#define DDR_PHY_DX8SL2DQSCTL_UDQIOM_MASK 0x00002000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10_MASK -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10_SHIFT 10 -#define DDR_PHY_DX8SL2DQSCTL_RESERVED_12_10_MASK 0x00001C00U - -/*Data Slew Rate*/ -#undef DDR_PHY_DX8SL2DQSCTL_DXSR_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_DXSR_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_DXSR_MASK -#define DDR_PHY_DX8SL2DQSCTL_DXSR_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_DXSR_SHIFT 8 -#define DDR_PHY_DX8SL2DQSCTL_DXSR_MASK 0x00000300U - -/*DQS_N Resistor*/ -#undef DDR_PHY_DX8SL2DQSCTL_DQSNRES_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_DQSNRES_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_DQSNRES_MASK -#define DDR_PHY_DX8SL2DQSCTL_DQSNRES_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_DQSNRES_SHIFT 4 -#define DDR_PHY_DX8SL2DQSCTL_DQSNRES_MASK 0x000000F0U - -/*DQS Resistor*/ -#undef DDR_PHY_DX8SL2DQSCTL_DQSRES_DEFVAL -#undef DDR_PHY_DX8SL2DQSCTL_DQSRES_SHIFT -#undef DDR_PHY_DX8SL2DQSCTL_DQSRES_MASK -#define DDR_PHY_DX8SL2DQSCTL_DQSRES_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL2DQSCTL_DQSRES_SHIFT 0 -#define DDR_PHY_DX8SL2DQSCTL_DQSRES_MASK 0x0000000FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24_MASK -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24_SHIFT 24 -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_31_24_MASK 0xFF000000U - -/*Configurable Read Data Enable*/ -#undef DDR_PHY_DX8SL2DXCTL2_CRDEN_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_CRDEN_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_CRDEN_MASK -#define DDR_PHY_DX8SL2DXCTL2_CRDEN_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_CRDEN_SHIFT 23 -#define DDR_PHY_DX8SL2DXCTL2_CRDEN_MASK 0x00800000U - -/*OX Extension during Post-amble*/ -#undef DDR_PHY_DX8SL2DXCTL2_POSOEX_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_POSOEX_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_POSOEX_MASK -#define DDR_PHY_DX8SL2DXCTL2_POSOEX_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_POSOEX_SHIFT 20 -#define DDR_PHY_DX8SL2DXCTL2_POSOEX_MASK 0x00700000U - -/*OE Extension during Pre-amble*/ -#undef DDR_PHY_DX8SL2DXCTL2_PREOEX_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_PREOEX_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_PREOEX_MASK -#define DDR_PHY_DX8SL2DXCTL2_PREOEX_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_PREOEX_SHIFT 18 -#define DDR_PHY_DX8SL2DXCTL2_PREOEX_MASK 0x000C0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_17_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_17_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_17_MASK -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_17_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_17_SHIFT 17 -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_17_MASK 0x00020000U - -/*I/O Assisted Gate Select*/ -#undef DDR_PHY_DX8SL2DXCTL2_IOAG_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_IOAG_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_IOAG_MASK -#define DDR_PHY_DX8SL2DXCTL2_IOAG_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_IOAG_SHIFT 16 -#define DDR_PHY_DX8SL2DXCTL2_IOAG_MASK 0x00010000U - -/*I/O Loopback Select*/ -#undef DDR_PHY_DX8SL2DXCTL2_IOLB_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_IOLB_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_IOLB_MASK -#define DDR_PHY_DX8SL2DXCTL2_IOLB_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_IOLB_SHIFT 15 -#define DDR_PHY_DX8SL2DXCTL2_IOLB_MASK 0x00008000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13_MASK -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13_SHIFT 13 -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_14_13_MASK 0x00006000U - -/*Low Power Wakeup Threshold*/ -#undef DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH_MASK -#define DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH_SHIFT 9 -#define DDR_PHY_DX8SL2DXCTL2_LPWAKEUP_THRSH_MASK 0x00001E00U - -/*Read Data Bus Inversion Enable*/ -#undef DDR_PHY_DX8SL2DXCTL2_RDBI_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_RDBI_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_RDBI_MASK -#define DDR_PHY_DX8SL2DXCTL2_RDBI_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_RDBI_SHIFT 8 -#define DDR_PHY_DX8SL2DXCTL2_RDBI_MASK 0x00000100U - -/*Write Data Bus Inversion Enable*/ -#undef DDR_PHY_DX8SL2DXCTL2_WDBI_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_WDBI_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_WDBI_MASK -#define DDR_PHY_DX8SL2DXCTL2_WDBI_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_WDBI_SHIFT 7 -#define DDR_PHY_DX8SL2DXCTL2_WDBI_MASK 0x00000080U - -/*PUB Read FIFO Bypass*/ -#undef DDR_PHY_DX8SL2DXCTL2_PRFBYP_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_PRFBYP_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_PRFBYP_MASK -#define DDR_PHY_DX8SL2DXCTL2_PRFBYP_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_PRFBYP_SHIFT 6 -#define DDR_PHY_DX8SL2DXCTL2_PRFBYP_MASK 0x00000040U - -/*DATX8 Receive FIFO Read Mode*/ -#undef DDR_PHY_DX8SL2DXCTL2_RDMODE_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_RDMODE_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_RDMODE_MASK -#define DDR_PHY_DX8SL2DXCTL2_RDMODE_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_RDMODE_SHIFT 4 -#define DDR_PHY_DX8SL2DXCTL2_RDMODE_MASK 0x00000030U - -/*Disables the Read FIFO Reset*/ -#undef DDR_PHY_DX8SL2DXCTL2_DISRST_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_DISRST_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_DISRST_MASK -#define DDR_PHY_DX8SL2DXCTL2_DISRST_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_DISRST_SHIFT 3 -#define DDR_PHY_DX8SL2DXCTL2_DISRST_MASK 0x00000008U - -/*Read DQS Gate I/O Loopback*/ -#undef DDR_PHY_DX8SL2DXCTL2_DQSGLB_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_DQSGLB_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_DQSGLB_MASK -#define DDR_PHY_DX8SL2DXCTL2_DQSGLB_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_DQSGLB_SHIFT 1 -#define DDR_PHY_DX8SL2DXCTL2_DQSGLB_MASK 0x00000006U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_0_DEFVAL -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_0_SHIFT -#undef DDR_PHY_DX8SL2DXCTL2_RESERVED_0_MASK -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_0_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_0_SHIFT 0 -#define DDR_PHY_DX8SL2DXCTL2_RESERVED_0_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL2IOCR_RESERVED_31_DEFVAL -#undef DDR_PHY_DX8SL2IOCR_RESERVED_31_SHIFT -#undef DDR_PHY_DX8SL2IOCR_RESERVED_31_MASK -#define DDR_PHY_DX8SL2IOCR_RESERVED_31_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL2IOCR_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX8SL2IOCR_RESERVED_31_MASK 0x80000000U - -/*PVREF_DAC REFSEL range select*/ -#undef DDR_PHY_DX8SL2IOCR_DXDACRANGE_DEFVAL -#undef DDR_PHY_DX8SL2IOCR_DXDACRANGE_SHIFT -#undef DDR_PHY_DX8SL2IOCR_DXDACRANGE_MASK -#define DDR_PHY_DX8SL2IOCR_DXDACRANGE_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL2IOCR_DXDACRANGE_SHIFT 28 -#define DDR_PHY_DX8SL2IOCR_DXDACRANGE_MASK 0x70000000U - -/*IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring*/ -#undef DDR_PHY_DX8SL2IOCR_DXVREFIOM_DEFVAL -#undef DDR_PHY_DX8SL2IOCR_DXVREFIOM_SHIFT -#undef DDR_PHY_DX8SL2IOCR_DXVREFIOM_MASK -#define DDR_PHY_DX8SL2IOCR_DXVREFIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL2IOCR_DXVREFIOM_SHIFT 25 -#define DDR_PHY_DX8SL2IOCR_DXVREFIOM_MASK 0x0E000000U - -/*DX IO Mode*/ -#undef DDR_PHY_DX8SL2IOCR_DXIOM_DEFVAL -#undef DDR_PHY_DX8SL2IOCR_DXIOM_SHIFT -#undef DDR_PHY_DX8SL2IOCR_DXIOM_MASK -#define DDR_PHY_DX8SL2IOCR_DXIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL2IOCR_DXIOM_SHIFT 22 -#define DDR_PHY_DX8SL2IOCR_DXIOM_MASK 0x01C00000U - -/*DX IO Transmitter Mode*/ -#undef DDR_PHY_DX8SL2IOCR_DXTXM_DEFVAL -#undef DDR_PHY_DX8SL2IOCR_DXTXM_SHIFT -#undef DDR_PHY_DX8SL2IOCR_DXTXM_MASK -#define DDR_PHY_DX8SL2IOCR_DXTXM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL2IOCR_DXTXM_SHIFT 11 -#define DDR_PHY_DX8SL2IOCR_DXTXM_MASK 0x003FF800U - -/*DX IO Receiver Mode*/ -#undef DDR_PHY_DX8SL2IOCR_DXRXM_DEFVAL -#undef DDR_PHY_DX8SL2IOCR_DXRXM_SHIFT -#undef DDR_PHY_DX8SL2IOCR_DXRXM_MASK -#define DDR_PHY_DX8SL2IOCR_DXRXM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL2IOCR_DXRXM_SHIFT 0 -#define DDR_PHY_DX8SL2IOCR_DXRXM_MASK 0x000007FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL3OSC_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX8SL3OSC_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX8SL3OSC_RESERVED_31_30_MASK -#define DDR_PHY_DX8SL3OSC_RESERVED_31_30_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX8SL3OSC_RESERVED_31_30_MASK 0xC0000000U - -/*Enable Clock Gating for DX ddr_clk*/ -#undef DDR_PHY_DX8SL3OSC_GATEDXRDCLK_DEFVAL -#undef DDR_PHY_DX8SL3OSC_GATEDXRDCLK_SHIFT -#undef DDR_PHY_DX8SL3OSC_GATEDXRDCLK_MASK -#define DDR_PHY_DX8SL3OSC_GATEDXRDCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_GATEDXRDCLK_SHIFT 28 -#define DDR_PHY_DX8SL3OSC_GATEDXRDCLK_MASK 0x30000000U - -/*Enable Clock Gating for DX ctl_rd_clk*/ -#undef DDR_PHY_DX8SL3OSC_GATEDXDDRCLK_DEFVAL -#undef DDR_PHY_DX8SL3OSC_GATEDXDDRCLK_SHIFT -#undef DDR_PHY_DX8SL3OSC_GATEDXDDRCLK_MASK -#define DDR_PHY_DX8SL3OSC_GATEDXDDRCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_GATEDXDDRCLK_SHIFT 26 -#define DDR_PHY_DX8SL3OSC_GATEDXDDRCLK_MASK 0x0C000000U - -/*Enable Clock Gating for DX ctl_clk*/ -#undef DDR_PHY_DX8SL3OSC_GATEDXCTLCLK_DEFVAL -#undef DDR_PHY_DX8SL3OSC_GATEDXCTLCLK_SHIFT -#undef DDR_PHY_DX8SL3OSC_GATEDXCTLCLK_MASK -#define DDR_PHY_DX8SL3OSC_GATEDXCTLCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_GATEDXCTLCLK_SHIFT 24 -#define DDR_PHY_DX8SL3OSC_GATEDXCTLCLK_MASK 0x03000000U - -/*Selects the level to which clocks will be stalled when clock gating is enabled.*/ -#undef DDR_PHY_DX8SL3OSC_CLKLEVEL_DEFVAL -#undef DDR_PHY_DX8SL3OSC_CLKLEVEL_SHIFT -#undef DDR_PHY_DX8SL3OSC_CLKLEVEL_MASK -#define DDR_PHY_DX8SL3OSC_CLKLEVEL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_CLKLEVEL_SHIFT 22 -#define DDR_PHY_DX8SL3OSC_CLKLEVEL_MASK 0x00C00000U - -/*Loopback Mode*/ -#undef DDR_PHY_DX8SL3OSC_LBMODE_DEFVAL -#undef DDR_PHY_DX8SL3OSC_LBMODE_SHIFT -#undef DDR_PHY_DX8SL3OSC_LBMODE_MASK -#define DDR_PHY_DX8SL3OSC_LBMODE_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_LBMODE_SHIFT 21 -#define DDR_PHY_DX8SL3OSC_LBMODE_MASK 0x00200000U - -/*Load GSDQS LCDL with 2x the calibrated GSDQSPRD value*/ -#undef DDR_PHY_DX8SL3OSC_LBGSDQS_DEFVAL -#undef DDR_PHY_DX8SL3OSC_LBGSDQS_SHIFT -#undef DDR_PHY_DX8SL3OSC_LBGSDQS_MASK -#define DDR_PHY_DX8SL3OSC_LBGSDQS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_LBGSDQS_SHIFT 20 -#define DDR_PHY_DX8SL3OSC_LBGSDQS_MASK 0x00100000U - -/*Loopback DQS Gating*/ -#undef DDR_PHY_DX8SL3OSC_LBGDQS_DEFVAL -#undef DDR_PHY_DX8SL3OSC_LBGDQS_SHIFT -#undef DDR_PHY_DX8SL3OSC_LBGDQS_MASK -#define DDR_PHY_DX8SL3OSC_LBGDQS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_LBGDQS_SHIFT 18 -#define DDR_PHY_DX8SL3OSC_LBGDQS_MASK 0x000C0000U - -/*Loopback DQS Shift*/ -#undef DDR_PHY_DX8SL3OSC_LBDQSS_DEFVAL -#undef DDR_PHY_DX8SL3OSC_LBDQSS_SHIFT -#undef DDR_PHY_DX8SL3OSC_LBDQSS_MASK -#define DDR_PHY_DX8SL3OSC_LBDQSS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_LBDQSS_SHIFT 17 -#define DDR_PHY_DX8SL3OSC_LBDQSS_MASK 0x00020000U - -/*PHY High-Speed Reset*/ -#undef DDR_PHY_DX8SL3OSC_PHYHRST_DEFVAL -#undef DDR_PHY_DX8SL3OSC_PHYHRST_SHIFT -#undef DDR_PHY_DX8SL3OSC_PHYHRST_MASK -#define DDR_PHY_DX8SL3OSC_PHYHRST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_PHYHRST_SHIFT 16 -#define DDR_PHY_DX8SL3OSC_PHYHRST_MASK 0x00010000U - -/*PHY FIFO Reset*/ -#undef DDR_PHY_DX8SL3OSC_PHYFRST_DEFVAL -#undef DDR_PHY_DX8SL3OSC_PHYFRST_SHIFT -#undef DDR_PHY_DX8SL3OSC_PHYFRST_MASK -#define DDR_PHY_DX8SL3OSC_PHYFRST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_PHYFRST_SHIFT 15 -#define DDR_PHY_DX8SL3OSC_PHYFRST_MASK 0x00008000U - -/*Delay Line Test Start*/ -#undef DDR_PHY_DX8SL3OSC_DLTST_DEFVAL -#undef DDR_PHY_DX8SL3OSC_DLTST_SHIFT -#undef DDR_PHY_DX8SL3OSC_DLTST_MASK -#define DDR_PHY_DX8SL3OSC_DLTST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_DLTST_SHIFT 14 -#define DDR_PHY_DX8SL3OSC_DLTST_MASK 0x00004000U - -/*Delay Line Test Mode*/ -#undef DDR_PHY_DX8SL3OSC_DLTMODE_DEFVAL -#undef DDR_PHY_DX8SL3OSC_DLTMODE_SHIFT -#undef DDR_PHY_DX8SL3OSC_DLTMODE_MASK -#define DDR_PHY_DX8SL3OSC_DLTMODE_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_DLTMODE_SHIFT 13 -#define DDR_PHY_DX8SL3OSC_DLTMODE_MASK 0x00002000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8SL3OSC_RESERVED_12_11_DEFVAL -#undef DDR_PHY_DX8SL3OSC_RESERVED_12_11_SHIFT -#undef DDR_PHY_DX8SL3OSC_RESERVED_12_11_MASK -#define DDR_PHY_DX8SL3OSC_RESERVED_12_11_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_RESERVED_12_11_SHIFT 11 -#define DDR_PHY_DX8SL3OSC_RESERVED_12_11_MASK 0x00001800U - -/*Oscillator Mode Write-Data Delay Line Select*/ -#undef DDR_PHY_DX8SL3OSC_OSCWDDL_DEFVAL -#undef DDR_PHY_DX8SL3OSC_OSCWDDL_SHIFT -#undef DDR_PHY_DX8SL3OSC_OSCWDDL_MASK -#define DDR_PHY_DX8SL3OSC_OSCWDDL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_OSCWDDL_SHIFT 9 -#define DDR_PHY_DX8SL3OSC_OSCWDDL_MASK 0x00000600U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8SL3OSC_RESERVED_8_7_DEFVAL -#undef DDR_PHY_DX8SL3OSC_RESERVED_8_7_SHIFT -#undef DDR_PHY_DX8SL3OSC_RESERVED_8_7_MASK -#define DDR_PHY_DX8SL3OSC_RESERVED_8_7_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_RESERVED_8_7_SHIFT 7 -#define DDR_PHY_DX8SL3OSC_RESERVED_8_7_MASK 0x00000180U - -/*Oscillator Mode Write-Leveling Delay Line Select*/ -#undef DDR_PHY_DX8SL3OSC_OSCWDL_DEFVAL -#undef DDR_PHY_DX8SL3OSC_OSCWDL_SHIFT -#undef DDR_PHY_DX8SL3OSC_OSCWDL_MASK -#define DDR_PHY_DX8SL3OSC_OSCWDL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_OSCWDL_SHIFT 5 -#define DDR_PHY_DX8SL3OSC_OSCWDL_MASK 0x00000060U - -/*Oscillator Mode Division*/ -#undef DDR_PHY_DX8SL3OSC_OSCDIV_DEFVAL -#undef DDR_PHY_DX8SL3OSC_OSCDIV_SHIFT -#undef DDR_PHY_DX8SL3OSC_OSCDIV_MASK -#define DDR_PHY_DX8SL3OSC_OSCDIV_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_OSCDIV_SHIFT 1 -#define DDR_PHY_DX8SL3OSC_OSCDIV_MASK 0x0000001EU - -/*Oscillator Enable*/ -#undef DDR_PHY_DX8SL3OSC_OSCEN_DEFVAL -#undef DDR_PHY_DX8SL3OSC_OSCEN_SHIFT -#undef DDR_PHY_DX8SL3OSC_OSCEN_MASK -#define DDR_PHY_DX8SL3OSC_OSCEN_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL3OSC_OSCEN_SHIFT 0 -#define DDR_PHY_DX8SL3OSC_OSCEN_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25_MASK -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_31_25_MASK 0xFE000000U - -/*Read Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SL3DQSCTL_RRRMODE_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_RRRMODE_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_RRRMODE_MASK -#define DDR_PHY_DX8SL3DQSCTL_RRRMODE_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_RRRMODE_SHIFT 24 -#define DDR_PHY_DX8SL3DQSCTL_RRRMODE_MASK 0x01000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22_MASK -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_23_22_MASK 0x00C00000U - -/*Write Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SL3DQSCTL_WRRMODE_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_WRRMODE_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_WRRMODE_MASK -#define DDR_PHY_DX8SL3DQSCTL_WRRMODE_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_WRRMODE_SHIFT 21 -#define DDR_PHY_DX8SL3DQSCTL_WRRMODE_MASK 0x00200000U - -/*DQS Gate Extension*/ -#undef DDR_PHY_DX8SL3DQSCTL_DQSGX_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_DQSGX_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_DQSGX_MASK -#define DDR_PHY_DX8SL3DQSCTL_DQSGX_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_DQSGX_SHIFT 19 -#define DDR_PHY_DX8SL3DQSCTL_DQSGX_MASK 0x00180000U - -/*Low Power PLL Power Down*/ -#undef DDR_PHY_DX8SL3DQSCTL_LPPLLPD_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_LPPLLPD_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_LPPLLPD_MASK -#define DDR_PHY_DX8SL3DQSCTL_LPPLLPD_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_LPPLLPD_SHIFT 18 -#define DDR_PHY_DX8SL3DQSCTL_LPPLLPD_MASK 0x00040000U - -/*Low Power I/O Power Down*/ -#undef DDR_PHY_DX8SL3DQSCTL_LPIOPD_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_LPIOPD_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_LPIOPD_MASK -#define DDR_PHY_DX8SL3DQSCTL_LPIOPD_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_LPIOPD_SHIFT 17 -#define DDR_PHY_DX8SL3DQSCTL_LPIOPD_MASK 0x00020000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15_MASK -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15_SHIFT 15 -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_16_15_MASK 0x00018000U - -/*QS Counter Enable*/ -#undef DDR_PHY_DX8SL3DQSCTL_QSCNTEN_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_QSCNTEN_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_QSCNTEN_MASK -#define DDR_PHY_DX8SL3DQSCTL_QSCNTEN_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_QSCNTEN_SHIFT 14 -#define DDR_PHY_DX8SL3DQSCTL_QSCNTEN_MASK 0x00004000U - -/*Unused DQ I/O Mode*/ -#undef DDR_PHY_DX8SL3DQSCTL_UDQIOM_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_UDQIOM_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_UDQIOM_MASK -#define DDR_PHY_DX8SL3DQSCTL_UDQIOM_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_UDQIOM_SHIFT 13 -#define DDR_PHY_DX8SL3DQSCTL_UDQIOM_MASK 0x00002000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10_MASK -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10_SHIFT 10 -#define DDR_PHY_DX8SL3DQSCTL_RESERVED_12_10_MASK 0x00001C00U - -/*Data Slew Rate*/ -#undef DDR_PHY_DX8SL3DQSCTL_DXSR_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_DXSR_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_DXSR_MASK -#define DDR_PHY_DX8SL3DQSCTL_DXSR_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_DXSR_SHIFT 8 -#define DDR_PHY_DX8SL3DQSCTL_DXSR_MASK 0x00000300U - -/*DQS_N Resistor*/ -#undef DDR_PHY_DX8SL3DQSCTL_DQSNRES_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_DQSNRES_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_DQSNRES_MASK -#define DDR_PHY_DX8SL3DQSCTL_DQSNRES_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_DQSNRES_SHIFT 4 -#define DDR_PHY_DX8SL3DQSCTL_DQSNRES_MASK 0x000000F0U - -/*DQS Resistor*/ -#undef DDR_PHY_DX8SL3DQSCTL_DQSRES_DEFVAL -#undef DDR_PHY_DX8SL3DQSCTL_DQSRES_SHIFT -#undef DDR_PHY_DX8SL3DQSCTL_DQSRES_MASK -#define DDR_PHY_DX8SL3DQSCTL_DQSRES_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL3DQSCTL_DQSRES_SHIFT 0 -#define DDR_PHY_DX8SL3DQSCTL_DQSRES_MASK 0x0000000FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24_MASK -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24_SHIFT 24 -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_31_24_MASK 0xFF000000U - -/*Configurable Read Data Enable*/ -#undef DDR_PHY_DX8SL3DXCTL2_CRDEN_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_CRDEN_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_CRDEN_MASK -#define DDR_PHY_DX8SL3DXCTL2_CRDEN_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_CRDEN_SHIFT 23 -#define DDR_PHY_DX8SL3DXCTL2_CRDEN_MASK 0x00800000U - -/*OX Extension during Post-amble*/ -#undef DDR_PHY_DX8SL3DXCTL2_POSOEX_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_POSOEX_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_POSOEX_MASK -#define DDR_PHY_DX8SL3DXCTL2_POSOEX_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_POSOEX_SHIFT 20 -#define DDR_PHY_DX8SL3DXCTL2_POSOEX_MASK 0x00700000U - -/*OE Extension during Pre-amble*/ -#undef DDR_PHY_DX8SL3DXCTL2_PREOEX_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_PREOEX_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_PREOEX_MASK -#define DDR_PHY_DX8SL3DXCTL2_PREOEX_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_PREOEX_SHIFT 18 -#define DDR_PHY_DX8SL3DXCTL2_PREOEX_MASK 0x000C0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_17_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_17_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_17_MASK -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_17_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_17_SHIFT 17 -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_17_MASK 0x00020000U - -/*I/O Assisted Gate Select*/ -#undef DDR_PHY_DX8SL3DXCTL2_IOAG_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_IOAG_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_IOAG_MASK -#define DDR_PHY_DX8SL3DXCTL2_IOAG_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_IOAG_SHIFT 16 -#define DDR_PHY_DX8SL3DXCTL2_IOAG_MASK 0x00010000U - -/*I/O Loopback Select*/ -#undef DDR_PHY_DX8SL3DXCTL2_IOLB_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_IOLB_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_IOLB_MASK -#define DDR_PHY_DX8SL3DXCTL2_IOLB_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_IOLB_SHIFT 15 -#define DDR_PHY_DX8SL3DXCTL2_IOLB_MASK 0x00008000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13_MASK -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13_SHIFT 13 -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_14_13_MASK 0x00006000U - -/*Low Power Wakeup Threshold*/ -#undef DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH_MASK -#define DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH_SHIFT 9 -#define DDR_PHY_DX8SL3DXCTL2_LPWAKEUP_THRSH_MASK 0x00001E00U - -/*Read Data Bus Inversion Enable*/ -#undef DDR_PHY_DX8SL3DXCTL2_RDBI_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_RDBI_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_RDBI_MASK -#define DDR_PHY_DX8SL3DXCTL2_RDBI_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_RDBI_SHIFT 8 -#define DDR_PHY_DX8SL3DXCTL2_RDBI_MASK 0x00000100U - -/*Write Data Bus Inversion Enable*/ -#undef DDR_PHY_DX8SL3DXCTL2_WDBI_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_WDBI_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_WDBI_MASK -#define DDR_PHY_DX8SL3DXCTL2_WDBI_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_WDBI_SHIFT 7 -#define DDR_PHY_DX8SL3DXCTL2_WDBI_MASK 0x00000080U - -/*PUB Read FIFO Bypass*/ -#undef DDR_PHY_DX8SL3DXCTL2_PRFBYP_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_PRFBYP_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_PRFBYP_MASK -#define DDR_PHY_DX8SL3DXCTL2_PRFBYP_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_PRFBYP_SHIFT 6 -#define DDR_PHY_DX8SL3DXCTL2_PRFBYP_MASK 0x00000040U - -/*DATX8 Receive FIFO Read Mode*/ -#undef DDR_PHY_DX8SL3DXCTL2_RDMODE_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_RDMODE_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_RDMODE_MASK -#define DDR_PHY_DX8SL3DXCTL2_RDMODE_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_RDMODE_SHIFT 4 -#define DDR_PHY_DX8SL3DXCTL2_RDMODE_MASK 0x00000030U - -/*Disables the Read FIFO Reset*/ -#undef DDR_PHY_DX8SL3DXCTL2_DISRST_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_DISRST_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_DISRST_MASK -#define DDR_PHY_DX8SL3DXCTL2_DISRST_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_DISRST_SHIFT 3 -#define DDR_PHY_DX8SL3DXCTL2_DISRST_MASK 0x00000008U - -/*Read DQS Gate I/O Loopback*/ -#undef DDR_PHY_DX8SL3DXCTL2_DQSGLB_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_DQSGLB_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_DQSGLB_MASK -#define DDR_PHY_DX8SL3DXCTL2_DQSGLB_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_DQSGLB_SHIFT 1 -#define DDR_PHY_DX8SL3DXCTL2_DQSGLB_MASK 0x00000006U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_0_DEFVAL -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_0_SHIFT -#undef DDR_PHY_DX8SL3DXCTL2_RESERVED_0_MASK -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_0_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_0_SHIFT 0 -#define DDR_PHY_DX8SL3DXCTL2_RESERVED_0_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL3IOCR_RESERVED_31_DEFVAL -#undef DDR_PHY_DX8SL3IOCR_RESERVED_31_SHIFT -#undef DDR_PHY_DX8SL3IOCR_RESERVED_31_MASK -#define DDR_PHY_DX8SL3IOCR_RESERVED_31_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL3IOCR_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX8SL3IOCR_RESERVED_31_MASK 0x80000000U - -/*PVREF_DAC REFSEL range select*/ -#undef DDR_PHY_DX8SL3IOCR_DXDACRANGE_DEFVAL -#undef DDR_PHY_DX8SL3IOCR_DXDACRANGE_SHIFT -#undef DDR_PHY_DX8SL3IOCR_DXDACRANGE_MASK -#define DDR_PHY_DX8SL3IOCR_DXDACRANGE_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL3IOCR_DXDACRANGE_SHIFT 28 -#define DDR_PHY_DX8SL3IOCR_DXDACRANGE_MASK 0x70000000U - -/*IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring*/ -#undef DDR_PHY_DX8SL3IOCR_DXVREFIOM_DEFVAL -#undef DDR_PHY_DX8SL3IOCR_DXVREFIOM_SHIFT -#undef DDR_PHY_DX8SL3IOCR_DXVREFIOM_MASK -#define DDR_PHY_DX8SL3IOCR_DXVREFIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL3IOCR_DXVREFIOM_SHIFT 25 -#define DDR_PHY_DX8SL3IOCR_DXVREFIOM_MASK 0x0E000000U - -/*DX IO Mode*/ -#undef DDR_PHY_DX8SL3IOCR_DXIOM_DEFVAL -#undef DDR_PHY_DX8SL3IOCR_DXIOM_SHIFT -#undef DDR_PHY_DX8SL3IOCR_DXIOM_MASK -#define DDR_PHY_DX8SL3IOCR_DXIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL3IOCR_DXIOM_SHIFT 22 -#define DDR_PHY_DX8SL3IOCR_DXIOM_MASK 0x01C00000U - -/*DX IO Transmitter Mode*/ -#undef DDR_PHY_DX8SL3IOCR_DXTXM_DEFVAL -#undef DDR_PHY_DX8SL3IOCR_DXTXM_SHIFT -#undef DDR_PHY_DX8SL3IOCR_DXTXM_MASK -#define DDR_PHY_DX8SL3IOCR_DXTXM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL3IOCR_DXTXM_SHIFT 11 -#define DDR_PHY_DX8SL3IOCR_DXTXM_MASK 0x003FF800U - -/*DX IO Receiver Mode*/ -#undef DDR_PHY_DX8SL3IOCR_DXRXM_DEFVAL -#undef DDR_PHY_DX8SL3IOCR_DXRXM_SHIFT -#undef DDR_PHY_DX8SL3IOCR_DXRXM_MASK -#define DDR_PHY_DX8SL3IOCR_DXRXM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL3IOCR_DXRXM_SHIFT 0 -#define DDR_PHY_DX8SL3IOCR_DXRXM_MASK 0x000007FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL4OSC_RESERVED_31_30_DEFVAL -#undef DDR_PHY_DX8SL4OSC_RESERVED_31_30_SHIFT -#undef DDR_PHY_DX8SL4OSC_RESERVED_31_30_MASK -#define DDR_PHY_DX8SL4OSC_RESERVED_31_30_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_RESERVED_31_30_SHIFT 30 -#define DDR_PHY_DX8SL4OSC_RESERVED_31_30_MASK 0xC0000000U - -/*Enable Clock Gating for DX ddr_clk*/ -#undef DDR_PHY_DX8SL4OSC_GATEDXRDCLK_DEFVAL -#undef DDR_PHY_DX8SL4OSC_GATEDXRDCLK_SHIFT -#undef DDR_PHY_DX8SL4OSC_GATEDXRDCLK_MASK -#define DDR_PHY_DX8SL4OSC_GATEDXRDCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_GATEDXRDCLK_SHIFT 28 -#define DDR_PHY_DX8SL4OSC_GATEDXRDCLK_MASK 0x30000000U - -/*Enable Clock Gating for DX ctl_rd_clk*/ -#undef DDR_PHY_DX8SL4OSC_GATEDXDDRCLK_DEFVAL -#undef DDR_PHY_DX8SL4OSC_GATEDXDDRCLK_SHIFT -#undef DDR_PHY_DX8SL4OSC_GATEDXDDRCLK_MASK -#define DDR_PHY_DX8SL4OSC_GATEDXDDRCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_GATEDXDDRCLK_SHIFT 26 -#define DDR_PHY_DX8SL4OSC_GATEDXDDRCLK_MASK 0x0C000000U - -/*Enable Clock Gating for DX ctl_clk*/ -#undef DDR_PHY_DX8SL4OSC_GATEDXCTLCLK_DEFVAL -#undef DDR_PHY_DX8SL4OSC_GATEDXCTLCLK_SHIFT -#undef DDR_PHY_DX8SL4OSC_GATEDXCTLCLK_MASK -#define DDR_PHY_DX8SL4OSC_GATEDXCTLCLK_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_GATEDXCTLCLK_SHIFT 24 -#define DDR_PHY_DX8SL4OSC_GATEDXCTLCLK_MASK 0x03000000U - -/*Selects the level to which clocks will be stalled when clock gating is enabled.*/ -#undef DDR_PHY_DX8SL4OSC_CLKLEVEL_DEFVAL -#undef DDR_PHY_DX8SL4OSC_CLKLEVEL_SHIFT -#undef DDR_PHY_DX8SL4OSC_CLKLEVEL_MASK -#define DDR_PHY_DX8SL4OSC_CLKLEVEL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_CLKLEVEL_SHIFT 22 -#define DDR_PHY_DX8SL4OSC_CLKLEVEL_MASK 0x00C00000U - -/*Loopback Mode*/ -#undef DDR_PHY_DX8SL4OSC_LBMODE_DEFVAL -#undef DDR_PHY_DX8SL4OSC_LBMODE_SHIFT -#undef DDR_PHY_DX8SL4OSC_LBMODE_MASK -#define DDR_PHY_DX8SL4OSC_LBMODE_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_LBMODE_SHIFT 21 -#define DDR_PHY_DX8SL4OSC_LBMODE_MASK 0x00200000U - -/*Load GSDQS LCDL with 2x the calibrated GSDQSPRD value*/ -#undef DDR_PHY_DX8SL4OSC_LBGSDQS_DEFVAL -#undef DDR_PHY_DX8SL4OSC_LBGSDQS_SHIFT -#undef DDR_PHY_DX8SL4OSC_LBGSDQS_MASK -#define DDR_PHY_DX8SL4OSC_LBGSDQS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_LBGSDQS_SHIFT 20 -#define DDR_PHY_DX8SL4OSC_LBGSDQS_MASK 0x00100000U - -/*Loopback DQS Gating*/ -#undef DDR_PHY_DX8SL4OSC_LBGDQS_DEFVAL -#undef DDR_PHY_DX8SL4OSC_LBGDQS_SHIFT -#undef DDR_PHY_DX8SL4OSC_LBGDQS_MASK -#define DDR_PHY_DX8SL4OSC_LBGDQS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_LBGDQS_SHIFT 18 -#define DDR_PHY_DX8SL4OSC_LBGDQS_MASK 0x000C0000U - -/*Loopback DQS Shift*/ -#undef DDR_PHY_DX8SL4OSC_LBDQSS_DEFVAL -#undef DDR_PHY_DX8SL4OSC_LBDQSS_SHIFT -#undef DDR_PHY_DX8SL4OSC_LBDQSS_MASK -#define DDR_PHY_DX8SL4OSC_LBDQSS_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_LBDQSS_SHIFT 17 -#define DDR_PHY_DX8SL4OSC_LBDQSS_MASK 0x00020000U - -/*PHY High-Speed Reset*/ -#undef DDR_PHY_DX8SL4OSC_PHYHRST_DEFVAL -#undef DDR_PHY_DX8SL4OSC_PHYHRST_SHIFT -#undef DDR_PHY_DX8SL4OSC_PHYHRST_MASK -#define DDR_PHY_DX8SL4OSC_PHYHRST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_PHYHRST_SHIFT 16 -#define DDR_PHY_DX8SL4OSC_PHYHRST_MASK 0x00010000U - -/*PHY FIFO Reset*/ -#undef DDR_PHY_DX8SL4OSC_PHYFRST_DEFVAL -#undef DDR_PHY_DX8SL4OSC_PHYFRST_SHIFT -#undef DDR_PHY_DX8SL4OSC_PHYFRST_MASK -#define DDR_PHY_DX8SL4OSC_PHYFRST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_PHYFRST_SHIFT 15 -#define DDR_PHY_DX8SL4OSC_PHYFRST_MASK 0x00008000U - -/*Delay Line Test Start*/ -#undef DDR_PHY_DX8SL4OSC_DLTST_DEFVAL -#undef DDR_PHY_DX8SL4OSC_DLTST_SHIFT -#undef DDR_PHY_DX8SL4OSC_DLTST_MASK -#define DDR_PHY_DX8SL4OSC_DLTST_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_DLTST_SHIFT 14 -#define DDR_PHY_DX8SL4OSC_DLTST_MASK 0x00004000U - -/*Delay Line Test Mode*/ -#undef DDR_PHY_DX8SL4OSC_DLTMODE_DEFVAL -#undef DDR_PHY_DX8SL4OSC_DLTMODE_SHIFT -#undef DDR_PHY_DX8SL4OSC_DLTMODE_MASK -#define DDR_PHY_DX8SL4OSC_DLTMODE_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_DLTMODE_SHIFT 13 -#define DDR_PHY_DX8SL4OSC_DLTMODE_MASK 0x00002000U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8SL4OSC_RESERVED_12_11_DEFVAL -#undef DDR_PHY_DX8SL4OSC_RESERVED_12_11_SHIFT -#undef DDR_PHY_DX8SL4OSC_RESERVED_12_11_MASK -#define DDR_PHY_DX8SL4OSC_RESERVED_12_11_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_RESERVED_12_11_SHIFT 11 -#define DDR_PHY_DX8SL4OSC_RESERVED_12_11_MASK 0x00001800U - -/*Oscillator Mode Write-Data Delay Line Select*/ -#undef DDR_PHY_DX8SL4OSC_OSCWDDL_DEFVAL -#undef DDR_PHY_DX8SL4OSC_OSCWDDL_SHIFT -#undef DDR_PHY_DX8SL4OSC_OSCWDDL_MASK -#define DDR_PHY_DX8SL4OSC_OSCWDDL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_OSCWDDL_SHIFT 9 -#define DDR_PHY_DX8SL4OSC_OSCWDDL_MASK 0x00000600U - -/*Reserved. Caution, do not write to this register field.*/ -#undef DDR_PHY_DX8SL4OSC_RESERVED_8_7_DEFVAL -#undef DDR_PHY_DX8SL4OSC_RESERVED_8_7_SHIFT -#undef DDR_PHY_DX8SL4OSC_RESERVED_8_7_MASK -#define DDR_PHY_DX8SL4OSC_RESERVED_8_7_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_RESERVED_8_7_SHIFT 7 -#define DDR_PHY_DX8SL4OSC_RESERVED_8_7_MASK 0x00000180U - -/*Oscillator Mode Write-Leveling Delay Line Select*/ -#undef DDR_PHY_DX8SL4OSC_OSCWDL_DEFVAL -#undef DDR_PHY_DX8SL4OSC_OSCWDL_SHIFT -#undef DDR_PHY_DX8SL4OSC_OSCWDL_MASK -#define DDR_PHY_DX8SL4OSC_OSCWDL_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_OSCWDL_SHIFT 5 -#define DDR_PHY_DX8SL4OSC_OSCWDL_MASK 0x00000060U - -/*Oscillator Mode Division*/ -#undef DDR_PHY_DX8SL4OSC_OSCDIV_DEFVAL -#undef DDR_PHY_DX8SL4OSC_OSCDIV_SHIFT -#undef DDR_PHY_DX8SL4OSC_OSCDIV_MASK -#define DDR_PHY_DX8SL4OSC_OSCDIV_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_OSCDIV_SHIFT 1 -#define DDR_PHY_DX8SL4OSC_OSCDIV_MASK 0x0000001EU - -/*Oscillator Enable*/ -#undef DDR_PHY_DX8SL4OSC_OSCEN_DEFVAL -#undef DDR_PHY_DX8SL4OSC_OSCEN_SHIFT -#undef DDR_PHY_DX8SL4OSC_OSCEN_MASK -#define DDR_PHY_DX8SL4OSC_OSCEN_DEFVAL 0x00019FFE -#define DDR_PHY_DX8SL4OSC_OSCEN_SHIFT 0 -#define DDR_PHY_DX8SL4OSC_OSCEN_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25_MASK -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_31_25_MASK 0xFE000000U - -/*Read Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SL4DQSCTL_RRRMODE_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_RRRMODE_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_RRRMODE_MASK -#define DDR_PHY_DX8SL4DQSCTL_RRRMODE_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_RRRMODE_SHIFT 24 -#define DDR_PHY_DX8SL4DQSCTL_RRRMODE_MASK 0x01000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22_MASK -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_23_22_MASK 0x00C00000U - -/*Write Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SL4DQSCTL_WRRMODE_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_WRRMODE_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_WRRMODE_MASK -#define DDR_PHY_DX8SL4DQSCTL_WRRMODE_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_WRRMODE_SHIFT 21 -#define DDR_PHY_DX8SL4DQSCTL_WRRMODE_MASK 0x00200000U - -/*DQS Gate Extension*/ -#undef DDR_PHY_DX8SL4DQSCTL_DQSGX_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_DQSGX_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_DQSGX_MASK -#define DDR_PHY_DX8SL4DQSCTL_DQSGX_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_DQSGX_SHIFT 19 -#define DDR_PHY_DX8SL4DQSCTL_DQSGX_MASK 0x00180000U - -/*Low Power PLL Power Down*/ -#undef DDR_PHY_DX8SL4DQSCTL_LPPLLPD_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_LPPLLPD_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_LPPLLPD_MASK -#define DDR_PHY_DX8SL4DQSCTL_LPPLLPD_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_LPPLLPD_SHIFT 18 -#define DDR_PHY_DX8SL4DQSCTL_LPPLLPD_MASK 0x00040000U - -/*Low Power I/O Power Down*/ -#undef DDR_PHY_DX8SL4DQSCTL_LPIOPD_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_LPIOPD_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_LPIOPD_MASK -#define DDR_PHY_DX8SL4DQSCTL_LPIOPD_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_LPIOPD_SHIFT 17 -#define DDR_PHY_DX8SL4DQSCTL_LPIOPD_MASK 0x00020000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15_MASK -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15_SHIFT 15 -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_16_15_MASK 0x00018000U - -/*QS Counter Enable*/ -#undef DDR_PHY_DX8SL4DQSCTL_QSCNTEN_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_QSCNTEN_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_QSCNTEN_MASK -#define DDR_PHY_DX8SL4DQSCTL_QSCNTEN_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_QSCNTEN_SHIFT 14 -#define DDR_PHY_DX8SL4DQSCTL_QSCNTEN_MASK 0x00004000U - -/*Unused DQ I/O Mode*/ -#undef DDR_PHY_DX8SL4DQSCTL_UDQIOM_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_UDQIOM_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_UDQIOM_MASK -#define DDR_PHY_DX8SL4DQSCTL_UDQIOM_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_UDQIOM_SHIFT 13 -#define DDR_PHY_DX8SL4DQSCTL_UDQIOM_MASK 0x00002000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10_MASK -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10_SHIFT 10 -#define DDR_PHY_DX8SL4DQSCTL_RESERVED_12_10_MASK 0x00001C00U - -/*Data Slew Rate*/ -#undef DDR_PHY_DX8SL4DQSCTL_DXSR_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_DXSR_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_DXSR_MASK -#define DDR_PHY_DX8SL4DQSCTL_DXSR_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_DXSR_SHIFT 8 -#define DDR_PHY_DX8SL4DQSCTL_DXSR_MASK 0x00000300U - -/*DQS_N Resistor*/ -#undef DDR_PHY_DX8SL4DQSCTL_DQSNRES_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_DQSNRES_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_DQSNRES_MASK -#define DDR_PHY_DX8SL4DQSCTL_DQSNRES_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_DQSNRES_SHIFT 4 -#define DDR_PHY_DX8SL4DQSCTL_DQSNRES_MASK 0x000000F0U - -/*DQS Resistor*/ -#undef DDR_PHY_DX8SL4DQSCTL_DQSRES_DEFVAL -#undef DDR_PHY_DX8SL4DQSCTL_DQSRES_SHIFT -#undef DDR_PHY_DX8SL4DQSCTL_DQSRES_MASK -#define DDR_PHY_DX8SL4DQSCTL_DQSRES_DEFVAL 0x01264000 -#define DDR_PHY_DX8SL4DQSCTL_DQSRES_SHIFT 0 -#define DDR_PHY_DX8SL4DQSCTL_DQSRES_MASK 0x0000000FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24_MASK -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24_SHIFT 24 -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_31_24_MASK 0xFF000000U - -/*Configurable Read Data Enable*/ -#undef DDR_PHY_DX8SL4DXCTL2_CRDEN_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_CRDEN_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_CRDEN_MASK -#define DDR_PHY_DX8SL4DXCTL2_CRDEN_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_CRDEN_SHIFT 23 -#define DDR_PHY_DX8SL4DXCTL2_CRDEN_MASK 0x00800000U - -/*OX Extension during Post-amble*/ -#undef DDR_PHY_DX8SL4DXCTL2_POSOEX_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_POSOEX_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_POSOEX_MASK -#define DDR_PHY_DX8SL4DXCTL2_POSOEX_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_POSOEX_SHIFT 20 -#define DDR_PHY_DX8SL4DXCTL2_POSOEX_MASK 0x00700000U - -/*OE Extension during Pre-amble*/ -#undef DDR_PHY_DX8SL4DXCTL2_PREOEX_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_PREOEX_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_PREOEX_MASK -#define DDR_PHY_DX8SL4DXCTL2_PREOEX_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_PREOEX_SHIFT 18 -#define DDR_PHY_DX8SL4DXCTL2_PREOEX_MASK 0x000C0000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_17_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_17_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_17_MASK -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_17_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_17_SHIFT 17 -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_17_MASK 0x00020000U - -/*I/O Assisted Gate Select*/ -#undef DDR_PHY_DX8SL4DXCTL2_IOAG_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_IOAG_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_IOAG_MASK -#define DDR_PHY_DX8SL4DXCTL2_IOAG_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_IOAG_SHIFT 16 -#define DDR_PHY_DX8SL4DXCTL2_IOAG_MASK 0x00010000U - -/*I/O Loopback Select*/ -#undef DDR_PHY_DX8SL4DXCTL2_IOLB_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_IOLB_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_IOLB_MASK -#define DDR_PHY_DX8SL4DXCTL2_IOLB_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_IOLB_SHIFT 15 -#define DDR_PHY_DX8SL4DXCTL2_IOLB_MASK 0x00008000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13_MASK -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13_SHIFT 13 -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_14_13_MASK 0x00006000U - -/*Low Power Wakeup Threshold*/ -#undef DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH_MASK -#define DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH_SHIFT 9 -#define DDR_PHY_DX8SL4DXCTL2_LPWAKEUP_THRSH_MASK 0x00001E00U - -/*Read Data Bus Inversion Enable*/ -#undef DDR_PHY_DX8SL4DXCTL2_RDBI_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_RDBI_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_RDBI_MASK -#define DDR_PHY_DX8SL4DXCTL2_RDBI_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_RDBI_SHIFT 8 -#define DDR_PHY_DX8SL4DXCTL2_RDBI_MASK 0x00000100U - -/*Write Data Bus Inversion Enable*/ -#undef DDR_PHY_DX8SL4DXCTL2_WDBI_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_WDBI_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_WDBI_MASK -#define DDR_PHY_DX8SL4DXCTL2_WDBI_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_WDBI_SHIFT 7 -#define DDR_PHY_DX8SL4DXCTL2_WDBI_MASK 0x00000080U - -/*PUB Read FIFO Bypass*/ -#undef DDR_PHY_DX8SL4DXCTL2_PRFBYP_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_PRFBYP_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_PRFBYP_MASK -#define DDR_PHY_DX8SL4DXCTL2_PRFBYP_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_PRFBYP_SHIFT 6 -#define DDR_PHY_DX8SL4DXCTL2_PRFBYP_MASK 0x00000040U - -/*DATX8 Receive FIFO Read Mode*/ -#undef DDR_PHY_DX8SL4DXCTL2_RDMODE_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_RDMODE_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_RDMODE_MASK -#define DDR_PHY_DX8SL4DXCTL2_RDMODE_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_RDMODE_SHIFT 4 -#define DDR_PHY_DX8SL4DXCTL2_RDMODE_MASK 0x00000030U - -/*Disables the Read FIFO Reset*/ -#undef DDR_PHY_DX8SL4DXCTL2_DISRST_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_DISRST_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_DISRST_MASK -#define DDR_PHY_DX8SL4DXCTL2_DISRST_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_DISRST_SHIFT 3 -#define DDR_PHY_DX8SL4DXCTL2_DISRST_MASK 0x00000008U - -/*Read DQS Gate I/O Loopback*/ -#undef DDR_PHY_DX8SL4DXCTL2_DQSGLB_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_DQSGLB_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_DQSGLB_MASK -#define DDR_PHY_DX8SL4DXCTL2_DQSGLB_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_DQSGLB_SHIFT 1 -#define DDR_PHY_DX8SL4DXCTL2_DQSGLB_MASK 0x00000006U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_0_DEFVAL -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_0_SHIFT -#undef DDR_PHY_DX8SL4DXCTL2_RESERVED_0_MASK -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_0_DEFVAL 0x00141800 -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_0_SHIFT 0 -#define DDR_PHY_DX8SL4DXCTL2_RESERVED_0_MASK 0x00000001U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SL4IOCR_RESERVED_31_DEFVAL -#undef DDR_PHY_DX8SL4IOCR_RESERVED_31_SHIFT -#undef DDR_PHY_DX8SL4IOCR_RESERVED_31_MASK -#define DDR_PHY_DX8SL4IOCR_RESERVED_31_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL4IOCR_RESERVED_31_SHIFT 31 -#define DDR_PHY_DX8SL4IOCR_RESERVED_31_MASK 0x80000000U - -/*PVREF_DAC REFSEL range select*/ -#undef DDR_PHY_DX8SL4IOCR_DXDACRANGE_DEFVAL -#undef DDR_PHY_DX8SL4IOCR_DXDACRANGE_SHIFT -#undef DDR_PHY_DX8SL4IOCR_DXDACRANGE_MASK -#define DDR_PHY_DX8SL4IOCR_DXDACRANGE_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL4IOCR_DXDACRANGE_SHIFT 28 -#define DDR_PHY_DX8SL4IOCR_DXDACRANGE_MASK 0x70000000U - -/*IOM bits for PVREF, PVREF_DAC and PVREFE cells in DX IO ring*/ -#undef DDR_PHY_DX8SL4IOCR_DXVREFIOM_DEFVAL -#undef DDR_PHY_DX8SL4IOCR_DXVREFIOM_SHIFT -#undef DDR_PHY_DX8SL4IOCR_DXVREFIOM_MASK -#define DDR_PHY_DX8SL4IOCR_DXVREFIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL4IOCR_DXVREFIOM_SHIFT 25 -#define DDR_PHY_DX8SL4IOCR_DXVREFIOM_MASK 0x0E000000U - -/*DX IO Mode*/ -#undef DDR_PHY_DX8SL4IOCR_DXIOM_DEFVAL -#undef DDR_PHY_DX8SL4IOCR_DXIOM_SHIFT -#undef DDR_PHY_DX8SL4IOCR_DXIOM_MASK -#define DDR_PHY_DX8SL4IOCR_DXIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL4IOCR_DXIOM_SHIFT 22 -#define DDR_PHY_DX8SL4IOCR_DXIOM_MASK 0x01C00000U - -/*DX IO Transmitter Mode*/ -#undef DDR_PHY_DX8SL4IOCR_DXTXM_DEFVAL -#undef DDR_PHY_DX8SL4IOCR_DXTXM_SHIFT -#undef DDR_PHY_DX8SL4IOCR_DXTXM_MASK -#define DDR_PHY_DX8SL4IOCR_DXTXM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL4IOCR_DXTXM_SHIFT 11 -#define DDR_PHY_DX8SL4IOCR_DXTXM_MASK 0x003FF800U - -/*DX IO Receiver Mode*/ -#undef DDR_PHY_DX8SL4IOCR_DXRXM_DEFVAL -#undef DDR_PHY_DX8SL4IOCR_DXRXM_SHIFT -#undef DDR_PHY_DX8SL4IOCR_DXRXM_MASK -#define DDR_PHY_DX8SL4IOCR_DXRXM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SL4IOCR_DXRXM_SHIFT 0 -#define DDR_PHY_DX8SL4IOCR_DXRXM_MASK 0x000007FFU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25_MASK -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25_SHIFT 25 -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_31_25_MASK 0xFE000000U - -/*Read Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SLBDQSCTL_RRRMODE_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_RRRMODE_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_RRRMODE_MASK -#define DDR_PHY_DX8SLBDQSCTL_RRRMODE_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_RRRMODE_SHIFT 24 -#define DDR_PHY_DX8SLBDQSCTL_RRRMODE_MASK 0x01000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22_MASK -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22_SHIFT 22 -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_23_22_MASK 0x00C00000U - -/*Write Path Rise-to-Rise Mode*/ -#undef DDR_PHY_DX8SLBDQSCTL_WRRMODE_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_WRRMODE_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_WRRMODE_MASK -#define DDR_PHY_DX8SLBDQSCTL_WRRMODE_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_WRRMODE_SHIFT 21 -#define DDR_PHY_DX8SLBDQSCTL_WRRMODE_MASK 0x00200000U - -/*DQS Gate Extension*/ -#undef DDR_PHY_DX8SLBDQSCTL_DQSGX_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_DQSGX_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_DQSGX_MASK -#define DDR_PHY_DX8SLBDQSCTL_DQSGX_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_DQSGX_SHIFT 19 -#define DDR_PHY_DX8SLBDQSCTL_DQSGX_MASK 0x00180000U - -/*Low Power PLL Power Down*/ -#undef DDR_PHY_DX8SLBDQSCTL_LPPLLPD_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_LPPLLPD_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_LPPLLPD_MASK -#define DDR_PHY_DX8SLBDQSCTL_LPPLLPD_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_LPPLLPD_SHIFT 18 -#define DDR_PHY_DX8SLBDQSCTL_LPPLLPD_MASK 0x00040000U - -/*Low Power I/O Power Down*/ -#undef DDR_PHY_DX8SLBDQSCTL_LPIOPD_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_LPIOPD_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_LPIOPD_MASK -#define DDR_PHY_DX8SLBDQSCTL_LPIOPD_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_LPIOPD_SHIFT 17 -#define DDR_PHY_DX8SLBDQSCTL_LPIOPD_MASK 0x00020000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15_MASK -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15_SHIFT 15 -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_16_15_MASK 0x00018000U - -/*QS Counter Enable*/ -#undef DDR_PHY_DX8SLBDQSCTL_QSCNTEN_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_QSCNTEN_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_QSCNTEN_MASK -#define DDR_PHY_DX8SLBDQSCTL_QSCNTEN_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_QSCNTEN_SHIFT 14 -#define DDR_PHY_DX8SLBDQSCTL_QSCNTEN_MASK 0x00004000U - -/*Unused DQ I/O Mode*/ -#undef DDR_PHY_DX8SLBDQSCTL_UDQIOM_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_UDQIOM_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_UDQIOM_MASK -#define DDR_PHY_DX8SLBDQSCTL_UDQIOM_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_UDQIOM_SHIFT 13 -#define DDR_PHY_DX8SLBDQSCTL_UDQIOM_MASK 0x00002000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10_MASK -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10_SHIFT 10 -#define DDR_PHY_DX8SLBDQSCTL_RESERVED_12_10_MASK 0x00001C00U - -/*Data Slew Rate*/ -#undef DDR_PHY_DX8SLBDQSCTL_DXSR_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_DXSR_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_DXSR_MASK -#define DDR_PHY_DX8SLBDQSCTL_DXSR_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_DXSR_SHIFT 8 -#define DDR_PHY_DX8SLBDQSCTL_DXSR_MASK 0x00000300U - -/*DQS# Resistor*/ -#undef DDR_PHY_DX8SLBDQSCTL_DQSNRES_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_DQSNRES_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_DQSNRES_MASK -#define DDR_PHY_DX8SLBDQSCTL_DQSNRES_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_DQSNRES_SHIFT 4 -#define DDR_PHY_DX8SLBDQSCTL_DQSNRES_MASK 0x000000F0U - -/*DQS Resistor*/ -#undef DDR_PHY_DX8SLBDQSCTL_DQSRES_DEFVAL -#undef DDR_PHY_DX8SLBDQSCTL_DQSRES_SHIFT -#undef DDR_PHY_DX8SLBDQSCTL_DQSRES_MASK -#define DDR_PHY_DX8SLBDQSCTL_DQSRES_DEFVAL 0x00000000 -#define DDR_PHY_DX8SLBDQSCTL_DQSRES_SHIFT 0 -#define DDR_PHY_DX8SLBDQSCTL_DQSRES_MASK 0x0000000FU - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_PIR_RESERVED_31_DEFVAL -#undef DDR_PHY_PIR_RESERVED_31_SHIFT -#undef DDR_PHY_PIR_RESERVED_31_MASK -#define DDR_PHY_PIR_RESERVED_31_DEFVAL 0x00000000 -#define DDR_PHY_PIR_RESERVED_31_SHIFT 31 -#define DDR_PHY_PIR_RESERVED_31_MASK 0x80000000U - -/*Impedance Calibration Bypass*/ -#undef DDR_PHY_PIR_ZCALBYP_DEFVAL -#undef DDR_PHY_PIR_ZCALBYP_SHIFT -#undef DDR_PHY_PIR_ZCALBYP_MASK -#define DDR_PHY_PIR_ZCALBYP_DEFVAL 0x00000000 -#define DDR_PHY_PIR_ZCALBYP_SHIFT 30 -#define DDR_PHY_PIR_ZCALBYP_MASK 0x40000000U - -/*Digital Delay Line (DDL) Calibration Pause*/ -#undef DDR_PHY_PIR_DCALPSE_DEFVAL -#undef DDR_PHY_PIR_DCALPSE_SHIFT -#undef DDR_PHY_PIR_DCALPSE_MASK -#define DDR_PHY_PIR_DCALPSE_DEFVAL 0x00000000 -#define DDR_PHY_PIR_DCALPSE_SHIFT 29 -#define DDR_PHY_PIR_DCALPSE_MASK 0x20000000U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_PIR_RESERVED_28_21_DEFVAL -#undef DDR_PHY_PIR_RESERVED_28_21_SHIFT -#undef DDR_PHY_PIR_RESERVED_28_21_MASK -#define DDR_PHY_PIR_RESERVED_28_21_DEFVAL 0x00000000 -#define DDR_PHY_PIR_RESERVED_28_21_SHIFT 21 -#define DDR_PHY_PIR_RESERVED_28_21_MASK 0x1FE00000U - -/*Write DQS2DQ Training*/ -#undef DDR_PHY_PIR_DQS2DQ_DEFVAL -#undef DDR_PHY_PIR_DQS2DQ_SHIFT -#undef DDR_PHY_PIR_DQS2DQ_MASK -#define DDR_PHY_PIR_DQS2DQ_DEFVAL 0x00000000 -#define DDR_PHY_PIR_DQS2DQ_SHIFT 20 -#define DDR_PHY_PIR_DQS2DQ_MASK 0x00100000U - -/*RDIMM Initialization*/ -#undef DDR_PHY_PIR_RDIMMINIT_DEFVAL -#undef DDR_PHY_PIR_RDIMMINIT_SHIFT -#undef DDR_PHY_PIR_RDIMMINIT_MASK -#define DDR_PHY_PIR_RDIMMINIT_DEFVAL 0x00000000 -#define DDR_PHY_PIR_RDIMMINIT_SHIFT 19 -#define DDR_PHY_PIR_RDIMMINIT_MASK 0x00080000U - -/*Controller DRAM Initialization*/ -#undef DDR_PHY_PIR_CTLDINIT_DEFVAL -#undef DDR_PHY_PIR_CTLDINIT_SHIFT -#undef DDR_PHY_PIR_CTLDINIT_MASK -#define DDR_PHY_PIR_CTLDINIT_DEFVAL 0x00000000 -#define DDR_PHY_PIR_CTLDINIT_SHIFT 18 -#define DDR_PHY_PIR_CTLDINIT_MASK 0x00040000U - -/*VREF Training*/ -#undef DDR_PHY_PIR_VREF_DEFVAL -#undef DDR_PHY_PIR_VREF_SHIFT -#undef DDR_PHY_PIR_VREF_MASK -#define DDR_PHY_PIR_VREF_DEFVAL 0x00000000 -#define DDR_PHY_PIR_VREF_SHIFT 17 -#define DDR_PHY_PIR_VREF_MASK 0x00020000U - -/*Static Read Training*/ -#undef DDR_PHY_PIR_SRD_DEFVAL -#undef DDR_PHY_PIR_SRD_SHIFT -#undef DDR_PHY_PIR_SRD_MASK -#define DDR_PHY_PIR_SRD_DEFVAL 0x00000000 -#define DDR_PHY_PIR_SRD_SHIFT 16 -#define DDR_PHY_PIR_SRD_MASK 0x00010000U - -/*Write Data Eye Training*/ -#undef DDR_PHY_PIR_WREYE_DEFVAL -#undef DDR_PHY_PIR_WREYE_SHIFT -#undef DDR_PHY_PIR_WREYE_MASK -#define DDR_PHY_PIR_WREYE_DEFVAL 0x00000000 -#define DDR_PHY_PIR_WREYE_SHIFT 15 -#define DDR_PHY_PIR_WREYE_MASK 0x00008000U - -/*Read Data Eye Training*/ -#undef DDR_PHY_PIR_RDEYE_DEFVAL -#undef DDR_PHY_PIR_RDEYE_SHIFT -#undef DDR_PHY_PIR_RDEYE_MASK -#define DDR_PHY_PIR_RDEYE_DEFVAL 0x00000000 -#define DDR_PHY_PIR_RDEYE_SHIFT 14 -#define DDR_PHY_PIR_RDEYE_MASK 0x00004000U - -/*Write Data Bit Deskew*/ -#undef DDR_PHY_PIR_WRDSKW_DEFVAL -#undef DDR_PHY_PIR_WRDSKW_SHIFT -#undef DDR_PHY_PIR_WRDSKW_MASK -#define DDR_PHY_PIR_WRDSKW_DEFVAL 0x00000000 -#define DDR_PHY_PIR_WRDSKW_SHIFT 13 -#define DDR_PHY_PIR_WRDSKW_MASK 0x00002000U - -/*Read Data Bit Deskew*/ -#undef DDR_PHY_PIR_RDDSKW_DEFVAL -#undef DDR_PHY_PIR_RDDSKW_SHIFT -#undef DDR_PHY_PIR_RDDSKW_MASK -#define DDR_PHY_PIR_RDDSKW_DEFVAL 0x00000000 -#define DDR_PHY_PIR_RDDSKW_SHIFT 12 -#define DDR_PHY_PIR_RDDSKW_MASK 0x00001000U - -/*Write Leveling Adjust*/ -#undef DDR_PHY_PIR_WLADJ_DEFVAL -#undef DDR_PHY_PIR_WLADJ_SHIFT -#undef DDR_PHY_PIR_WLADJ_MASK -#define DDR_PHY_PIR_WLADJ_DEFVAL 0x00000000 -#define DDR_PHY_PIR_WLADJ_SHIFT 11 -#define DDR_PHY_PIR_WLADJ_MASK 0x00000800U - -/*Read DQS Gate Training*/ -#undef DDR_PHY_PIR_QSGATE_DEFVAL -#undef DDR_PHY_PIR_QSGATE_SHIFT -#undef DDR_PHY_PIR_QSGATE_MASK -#define DDR_PHY_PIR_QSGATE_DEFVAL 0x00000000 -#define DDR_PHY_PIR_QSGATE_SHIFT 10 -#define DDR_PHY_PIR_QSGATE_MASK 0x00000400U - -/*Write Leveling*/ -#undef DDR_PHY_PIR_WL_DEFVAL -#undef DDR_PHY_PIR_WL_SHIFT -#undef DDR_PHY_PIR_WL_MASK -#define DDR_PHY_PIR_WL_DEFVAL 0x00000000 -#define DDR_PHY_PIR_WL_SHIFT 9 -#define DDR_PHY_PIR_WL_MASK 0x00000200U - -/*DRAM Initialization*/ -#undef DDR_PHY_PIR_DRAMINIT_DEFVAL -#undef DDR_PHY_PIR_DRAMINIT_SHIFT -#undef DDR_PHY_PIR_DRAMINIT_MASK -#define DDR_PHY_PIR_DRAMINIT_DEFVAL 0x00000000 -#define DDR_PHY_PIR_DRAMINIT_SHIFT 8 -#define DDR_PHY_PIR_DRAMINIT_MASK 0x00000100U - -/*DRAM Reset (DDR3/DDR4/LPDDR4 Only)*/ -#undef DDR_PHY_PIR_DRAMRST_DEFVAL -#undef DDR_PHY_PIR_DRAMRST_SHIFT -#undef DDR_PHY_PIR_DRAMRST_MASK -#define DDR_PHY_PIR_DRAMRST_DEFVAL 0x00000000 -#define DDR_PHY_PIR_DRAMRST_SHIFT 7 -#define DDR_PHY_PIR_DRAMRST_MASK 0x00000080U - -/*PHY Reset*/ -#undef DDR_PHY_PIR_PHYRST_DEFVAL -#undef DDR_PHY_PIR_PHYRST_SHIFT -#undef DDR_PHY_PIR_PHYRST_MASK -#define DDR_PHY_PIR_PHYRST_DEFVAL 0x00000000 -#define DDR_PHY_PIR_PHYRST_SHIFT 6 -#define DDR_PHY_PIR_PHYRST_MASK 0x00000040U - -/*Digital Delay Line (DDL) Calibration*/ -#undef DDR_PHY_PIR_DCAL_DEFVAL -#undef DDR_PHY_PIR_DCAL_SHIFT -#undef DDR_PHY_PIR_DCAL_MASK -#define DDR_PHY_PIR_DCAL_DEFVAL 0x00000000 -#define DDR_PHY_PIR_DCAL_SHIFT 5 -#define DDR_PHY_PIR_DCAL_MASK 0x00000020U - -/*PLL Initialiazation*/ -#undef DDR_PHY_PIR_PLLINIT_DEFVAL -#undef DDR_PHY_PIR_PLLINIT_SHIFT -#undef DDR_PHY_PIR_PLLINIT_MASK -#define DDR_PHY_PIR_PLLINIT_DEFVAL 0x00000000 -#define DDR_PHY_PIR_PLLINIT_SHIFT 4 -#define DDR_PHY_PIR_PLLINIT_MASK 0x00000010U - -/*Reserved. Return zeroes on reads.*/ -#undef DDR_PHY_PIR_RESERVED_3_DEFVAL -#undef DDR_PHY_PIR_RESERVED_3_SHIFT -#undef DDR_PHY_PIR_RESERVED_3_MASK -#define DDR_PHY_PIR_RESERVED_3_DEFVAL 0x00000000 -#define DDR_PHY_PIR_RESERVED_3_SHIFT 3 -#define DDR_PHY_PIR_RESERVED_3_MASK 0x00000008U - -/*CA Training*/ -#undef DDR_PHY_PIR_CA_DEFVAL -#undef DDR_PHY_PIR_CA_SHIFT -#undef DDR_PHY_PIR_CA_MASK -#define DDR_PHY_PIR_CA_DEFVAL 0x00000000 -#define DDR_PHY_PIR_CA_SHIFT 2 -#define DDR_PHY_PIR_CA_MASK 0x00000004U - -/*Impedance Calibration*/ -#undef DDR_PHY_PIR_ZCAL_DEFVAL -#undef DDR_PHY_PIR_ZCAL_SHIFT -#undef DDR_PHY_PIR_ZCAL_MASK -#define DDR_PHY_PIR_ZCAL_DEFVAL 0x00000000 -#define DDR_PHY_PIR_ZCAL_SHIFT 1 -#define DDR_PHY_PIR_ZCAL_MASK 0x00000002U - -/*Initialization Trigger*/ -#undef DDR_PHY_PIR_INIT_DEFVAL -#undef DDR_PHY_PIR_INIT_SHIFT -#undef DDR_PHY_PIR_INIT_MASK -#define DDR_PHY_PIR_INIT_DEFVAL 0x00000000 -#define DDR_PHY_PIR_INIT_SHIFT 0 -#define DDR_PHY_PIR_INIT_MASK 0x00000001U -#undef IOU_SLCR_MIO_PIN_0_OFFSET -#define IOU_SLCR_MIO_PIN_0_OFFSET 0XFF180000 -#undef IOU_SLCR_MIO_PIN_1_OFFSET -#define IOU_SLCR_MIO_PIN_1_OFFSET 0XFF180004 -#undef IOU_SLCR_MIO_PIN_2_OFFSET -#define IOU_SLCR_MIO_PIN_2_OFFSET 0XFF180008 -#undef IOU_SLCR_MIO_PIN_3_OFFSET -#define IOU_SLCR_MIO_PIN_3_OFFSET 0XFF18000C -#undef IOU_SLCR_MIO_PIN_4_OFFSET -#define IOU_SLCR_MIO_PIN_4_OFFSET 0XFF180010 -#undef IOU_SLCR_MIO_PIN_5_OFFSET -#define IOU_SLCR_MIO_PIN_5_OFFSET 0XFF180014 -#undef IOU_SLCR_MIO_PIN_6_OFFSET -#define IOU_SLCR_MIO_PIN_6_OFFSET 0XFF180018 -#undef IOU_SLCR_MIO_PIN_7_OFFSET -#define IOU_SLCR_MIO_PIN_7_OFFSET 0XFF18001C -#undef IOU_SLCR_MIO_PIN_8_OFFSET -#define IOU_SLCR_MIO_PIN_8_OFFSET 0XFF180020 -#undef IOU_SLCR_MIO_PIN_9_OFFSET -#define IOU_SLCR_MIO_PIN_9_OFFSET 0XFF180024 -#undef IOU_SLCR_MIO_PIN_10_OFFSET -#define IOU_SLCR_MIO_PIN_10_OFFSET 0XFF180028 -#undef IOU_SLCR_MIO_PIN_11_OFFSET -#define IOU_SLCR_MIO_PIN_11_OFFSET 0XFF18002C -#undef IOU_SLCR_MIO_PIN_12_OFFSET -#define IOU_SLCR_MIO_PIN_12_OFFSET 0XFF180030 -#undef IOU_SLCR_MIO_PIN_13_OFFSET -#define IOU_SLCR_MIO_PIN_13_OFFSET 0XFF180034 -#undef IOU_SLCR_MIO_PIN_14_OFFSET -#define IOU_SLCR_MIO_PIN_14_OFFSET 0XFF180038 -#undef IOU_SLCR_MIO_PIN_15_OFFSET -#define IOU_SLCR_MIO_PIN_15_OFFSET 0XFF18003C -#undef IOU_SLCR_MIO_PIN_16_OFFSET -#define IOU_SLCR_MIO_PIN_16_OFFSET 0XFF180040 -#undef IOU_SLCR_MIO_PIN_17_OFFSET -#define IOU_SLCR_MIO_PIN_17_OFFSET 0XFF180044 -#undef IOU_SLCR_MIO_PIN_18_OFFSET -#define IOU_SLCR_MIO_PIN_18_OFFSET 0XFF180048 -#undef IOU_SLCR_MIO_PIN_19_OFFSET -#define IOU_SLCR_MIO_PIN_19_OFFSET 0XFF18004C -#undef IOU_SLCR_MIO_PIN_20_OFFSET -#define IOU_SLCR_MIO_PIN_20_OFFSET 0XFF180050 -#undef IOU_SLCR_MIO_PIN_21_OFFSET -#define IOU_SLCR_MIO_PIN_21_OFFSET 0XFF180054 -#undef IOU_SLCR_MIO_PIN_22_OFFSET -#define IOU_SLCR_MIO_PIN_22_OFFSET 0XFF180058 -#undef IOU_SLCR_MIO_PIN_23_OFFSET -#define IOU_SLCR_MIO_PIN_23_OFFSET 0XFF18005C -#undef IOU_SLCR_MIO_PIN_24_OFFSET -#define IOU_SLCR_MIO_PIN_24_OFFSET 0XFF180060 -#undef IOU_SLCR_MIO_PIN_25_OFFSET -#define IOU_SLCR_MIO_PIN_25_OFFSET 0XFF180064 -#undef IOU_SLCR_MIO_PIN_26_OFFSET -#define IOU_SLCR_MIO_PIN_26_OFFSET 0XFF180068 -#undef IOU_SLCR_MIO_PIN_27_OFFSET -#define IOU_SLCR_MIO_PIN_27_OFFSET 0XFF18006C -#undef IOU_SLCR_MIO_PIN_28_OFFSET -#define IOU_SLCR_MIO_PIN_28_OFFSET 0XFF180070 -#undef IOU_SLCR_MIO_PIN_29_OFFSET -#define IOU_SLCR_MIO_PIN_29_OFFSET 0XFF180074 -#undef IOU_SLCR_MIO_PIN_30_OFFSET -#define IOU_SLCR_MIO_PIN_30_OFFSET 0XFF180078 -#undef IOU_SLCR_MIO_PIN_31_OFFSET -#define IOU_SLCR_MIO_PIN_31_OFFSET 0XFF18007C -#undef IOU_SLCR_MIO_PIN_32_OFFSET -#define IOU_SLCR_MIO_PIN_32_OFFSET 0XFF180080 -#undef IOU_SLCR_MIO_PIN_33_OFFSET -#define IOU_SLCR_MIO_PIN_33_OFFSET 0XFF180084 -#undef IOU_SLCR_MIO_PIN_34_OFFSET -#define IOU_SLCR_MIO_PIN_34_OFFSET 0XFF180088 -#undef IOU_SLCR_MIO_PIN_35_OFFSET -#define IOU_SLCR_MIO_PIN_35_OFFSET 0XFF18008C -#undef IOU_SLCR_MIO_PIN_36_OFFSET -#define IOU_SLCR_MIO_PIN_36_OFFSET 0XFF180090 -#undef IOU_SLCR_MIO_PIN_37_OFFSET -#define IOU_SLCR_MIO_PIN_37_OFFSET 0XFF180094 -#undef IOU_SLCR_MIO_PIN_38_OFFSET -#define IOU_SLCR_MIO_PIN_38_OFFSET 0XFF180098 -#undef IOU_SLCR_MIO_PIN_39_OFFSET -#define IOU_SLCR_MIO_PIN_39_OFFSET 0XFF18009C -#undef IOU_SLCR_MIO_PIN_40_OFFSET -#define IOU_SLCR_MIO_PIN_40_OFFSET 0XFF1800A0 -#undef IOU_SLCR_MIO_PIN_41_OFFSET -#define IOU_SLCR_MIO_PIN_41_OFFSET 0XFF1800A4 -#undef IOU_SLCR_MIO_PIN_42_OFFSET -#define IOU_SLCR_MIO_PIN_42_OFFSET 0XFF1800A8 -#undef IOU_SLCR_MIO_PIN_43_OFFSET -#define IOU_SLCR_MIO_PIN_43_OFFSET 0XFF1800AC -#undef IOU_SLCR_MIO_PIN_44_OFFSET -#define IOU_SLCR_MIO_PIN_44_OFFSET 0XFF1800B0 -#undef IOU_SLCR_MIO_PIN_45_OFFSET -#define IOU_SLCR_MIO_PIN_45_OFFSET 0XFF1800B4 -#undef IOU_SLCR_MIO_PIN_46_OFFSET -#define IOU_SLCR_MIO_PIN_46_OFFSET 0XFF1800B8 -#undef IOU_SLCR_MIO_PIN_47_OFFSET -#define IOU_SLCR_MIO_PIN_47_OFFSET 0XFF1800BC -#undef IOU_SLCR_MIO_PIN_48_OFFSET -#define IOU_SLCR_MIO_PIN_48_OFFSET 0XFF1800C0 -#undef IOU_SLCR_MIO_PIN_49_OFFSET -#define IOU_SLCR_MIO_PIN_49_OFFSET 0XFF1800C4 -#undef IOU_SLCR_MIO_PIN_50_OFFSET -#define IOU_SLCR_MIO_PIN_50_OFFSET 0XFF1800C8 -#undef IOU_SLCR_MIO_PIN_51_OFFSET -#define IOU_SLCR_MIO_PIN_51_OFFSET 0XFF1800CC -#undef IOU_SLCR_MIO_PIN_52_OFFSET -#define IOU_SLCR_MIO_PIN_52_OFFSET 0XFF1800D0 -#undef IOU_SLCR_MIO_PIN_53_OFFSET -#define IOU_SLCR_MIO_PIN_53_OFFSET 0XFF1800D4 -#undef IOU_SLCR_MIO_PIN_54_OFFSET -#define IOU_SLCR_MIO_PIN_54_OFFSET 0XFF1800D8 -#undef IOU_SLCR_MIO_PIN_55_OFFSET -#define IOU_SLCR_MIO_PIN_55_OFFSET 0XFF1800DC -#undef IOU_SLCR_MIO_PIN_56_OFFSET -#define IOU_SLCR_MIO_PIN_56_OFFSET 0XFF1800E0 -#undef IOU_SLCR_MIO_PIN_57_OFFSET -#define IOU_SLCR_MIO_PIN_57_OFFSET 0XFF1800E4 -#undef IOU_SLCR_MIO_PIN_58_OFFSET -#define IOU_SLCR_MIO_PIN_58_OFFSET 0XFF1800E8 -#undef IOU_SLCR_MIO_PIN_59_OFFSET -#define IOU_SLCR_MIO_PIN_59_OFFSET 0XFF1800EC -#undef IOU_SLCR_MIO_PIN_60_OFFSET -#define IOU_SLCR_MIO_PIN_60_OFFSET 0XFF1800F0 -#undef IOU_SLCR_MIO_PIN_61_OFFSET -#define IOU_SLCR_MIO_PIN_61_OFFSET 0XFF1800F4 -#undef IOU_SLCR_MIO_PIN_62_OFFSET -#define IOU_SLCR_MIO_PIN_62_OFFSET 0XFF1800F8 -#undef IOU_SLCR_MIO_PIN_63_OFFSET -#define IOU_SLCR_MIO_PIN_63_OFFSET 0XFF1800FC -#undef IOU_SLCR_MIO_PIN_64_OFFSET -#define IOU_SLCR_MIO_PIN_64_OFFSET 0XFF180100 -#undef IOU_SLCR_MIO_PIN_65_OFFSET -#define IOU_SLCR_MIO_PIN_65_OFFSET 0XFF180104 -#undef IOU_SLCR_MIO_PIN_66_OFFSET -#define IOU_SLCR_MIO_PIN_66_OFFSET 0XFF180108 -#undef IOU_SLCR_MIO_PIN_67_OFFSET -#define IOU_SLCR_MIO_PIN_67_OFFSET 0XFF18010C -#undef IOU_SLCR_MIO_PIN_68_OFFSET -#define IOU_SLCR_MIO_PIN_68_OFFSET 0XFF180110 -#undef IOU_SLCR_MIO_PIN_69_OFFSET -#define IOU_SLCR_MIO_PIN_69_OFFSET 0XFF180114 -#undef IOU_SLCR_MIO_PIN_70_OFFSET -#define IOU_SLCR_MIO_PIN_70_OFFSET 0XFF180118 -#undef IOU_SLCR_MIO_PIN_71_OFFSET -#define IOU_SLCR_MIO_PIN_71_OFFSET 0XFF18011C -#undef IOU_SLCR_MIO_PIN_72_OFFSET -#define IOU_SLCR_MIO_PIN_72_OFFSET 0XFF180120 -#undef IOU_SLCR_MIO_PIN_73_OFFSET -#define IOU_SLCR_MIO_PIN_73_OFFSET 0XFF180124 -#undef IOU_SLCR_MIO_PIN_74_OFFSET -#define IOU_SLCR_MIO_PIN_74_OFFSET 0XFF180128 -#undef IOU_SLCR_MIO_PIN_75_OFFSET -#define IOU_SLCR_MIO_PIN_75_OFFSET 0XFF18012C -#undef IOU_SLCR_MIO_PIN_76_OFFSET -#define IOU_SLCR_MIO_PIN_76_OFFSET 0XFF180130 -#undef IOU_SLCR_MIO_PIN_77_OFFSET -#define IOU_SLCR_MIO_PIN_77_OFFSET 0XFF180134 -#undef IOU_SLCR_MIO_MST_TRI0_OFFSET -#define IOU_SLCR_MIO_MST_TRI0_OFFSET 0XFF180204 -#undef IOU_SLCR_MIO_MST_TRI1_OFFSET -#define IOU_SLCR_MIO_MST_TRI1_OFFSET 0XFF180208 -#undef IOU_SLCR_MIO_MST_TRI2_OFFSET -#define IOU_SLCR_MIO_MST_TRI2_OFFSET 0XFF18020C -#undef IOU_SLCR_BANK0_CTRL0_OFFSET -#define IOU_SLCR_BANK0_CTRL0_OFFSET 0XFF180138 -#undef IOU_SLCR_BANK0_CTRL1_OFFSET -#define IOU_SLCR_BANK0_CTRL1_OFFSET 0XFF18013C -#undef IOU_SLCR_BANK0_CTRL3_OFFSET -#define IOU_SLCR_BANK0_CTRL3_OFFSET 0XFF180140 -#undef IOU_SLCR_BANK0_CTRL4_OFFSET -#define IOU_SLCR_BANK0_CTRL4_OFFSET 0XFF180144 -#undef IOU_SLCR_BANK0_CTRL5_OFFSET -#define IOU_SLCR_BANK0_CTRL5_OFFSET 0XFF180148 -#undef IOU_SLCR_BANK0_CTRL6_OFFSET -#define IOU_SLCR_BANK0_CTRL6_OFFSET 0XFF18014C -#undef IOU_SLCR_BANK1_CTRL0_OFFSET -#define IOU_SLCR_BANK1_CTRL0_OFFSET 0XFF180154 -#undef IOU_SLCR_BANK1_CTRL1_OFFSET -#define IOU_SLCR_BANK1_CTRL1_OFFSET 0XFF180158 -#undef IOU_SLCR_BANK1_CTRL3_OFFSET -#define IOU_SLCR_BANK1_CTRL3_OFFSET 0XFF18015C -#undef IOU_SLCR_BANK1_CTRL4_OFFSET -#define IOU_SLCR_BANK1_CTRL4_OFFSET 0XFF180160 -#undef IOU_SLCR_BANK1_CTRL5_OFFSET -#define IOU_SLCR_BANK1_CTRL5_OFFSET 0XFF180164 -#undef IOU_SLCR_BANK1_CTRL6_OFFSET -#define IOU_SLCR_BANK1_CTRL6_OFFSET 0XFF180168 -#undef IOU_SLCR_BANK2_CTRL0_OFFSET -#define IOU_SLCR_BANK2_CTRL0_OFFSET 0XFF180170 -#undef IOU_SLCR_BANK2_CTRL1_OFFSET -#define IOU_SLCR_BANK2_CTRL1_OFFSET 0XFF180174 -#undef IOU_SLCR_BANK2_CTRL3_OFFSET -#define IOU_SLCR_BANK2_CTRL3_OFFSET 0XFF180178 -#undef IOU_SLCR_BANK2_CTRL4_OFFSET -#define IOU_SLCR_BANK2_CTRL4_OFFSET 0XFF18017C -#undef IOU_SLCR_BANK2_CTRL5_OFFSET -#define IOU_SLCR_BANK2_CTRL5_OFFSET 0XFF180180 -#undef IOU_SLCR_BANK2_CTRL6_OFFSET -#define IOU_SLCR_BANK2_CTRL6_OFFSET 0XFF180184 -#undef IOU_SLCR_MIO_LOOPBACK_OFFSET -#define IOU_SLCR_MIO_LOOPBACK_OFFSET 0XFF180200 - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_sclk_out- (QSPI Clock)*/ -#undef IOU_SLCR_MIO_PIN_0_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_0_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_0_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_0_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_0_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_0_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_0_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_0_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_0_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_0_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_0_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_0_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[0]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[0]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_0_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_0_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_0_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_0_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_0_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_0_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[0]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[0]- (GPIO bank 0) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Cloc - ) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, trace_ - lk- (Trace Port Clock)*/ -#undef IOU_SLCR_MIO_PIN_0_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_0_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_0_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_0_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_0_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_0_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_mi1- (QSPI Databus) 1= qspi, Output, qspi_so_mo1- (QSPI Data - us)*/ -#undef IOU_SLCR_MIO_PIN_1_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_1_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_1_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_1_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_1_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_1_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_1_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_1_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_1_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_1_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_1_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_1_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[1]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[1]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_1_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_1_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_1_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_1_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_1_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_1_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[1]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[1]- (GPIO bank 0) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc3, Output, ttc3_wave_o - t- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, trace_ctl- (Trace Port Control - Signal)*/ -#undef IOU_SLCR_MIO_PIN_1_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_1_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_1_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_1_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_1_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_1_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi2- (QSPI Databus) 1= qspi, Output, qspi_mo2- (QSPI Databus)*/ -#undef IOU_SLCR_MIO_PIN_2_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_2_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_2_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_2_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_2_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_2_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_2_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_2_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_2_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_2_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_2_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_2_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[2]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[2]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_2_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_2_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_2_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_2_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_2_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_2_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[2]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[2]- (GPIO bank 0) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc2, Input, ttc2_clk_in - (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[0]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_2_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_2_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_2_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_2_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_2_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_2_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi3- (QSPI Databus) 1= qspi, Output, qspi_mo3- (QSPI Databus)*/ -#undef IOU_SLCR_MIO_PIN_3_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_3_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_3_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_3_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_3_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_3_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_3_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_3_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_3_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_3_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_3_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_3_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[3]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[3]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_3_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_3_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_3_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_3_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_3_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_3_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[3]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[3]- (GPIO bank 0) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[0 - - (SPI Master Selects) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial - output) 7= trace, Output, tracedq[1]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_3_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_3_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_3_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_3_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_3_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_3_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_mo_mo0- (QSPI Databus) 1= qspi, Input, qspi_si_mi0- (QSPI Data - us)*/ -#undef IOU_SLCR_MIO_PIN_4_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_4_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_4_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_4_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_4_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_4_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_4_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_4_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_4_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_4_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_4_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_4_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[4]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[4]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_4_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_4_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_4_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_4_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_4_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_4_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[4]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[4]- (GPIO bank 0) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_s - - (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, - utput, tracedq[2]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_4_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_4_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_4_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_4_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_4_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_4_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_n_ss_out- (QSPI Slave Select)*/ -#undef IOU_SLCR_MIO_PIN_5_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_5_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_5_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_5_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_5_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_5_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_5_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_5_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_5_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_5_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_5_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_5_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[5]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[5]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_5_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_5_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_5_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_5_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_5_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_5_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[5]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[5]- (GPIO bank 0) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, spi0 - si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7 - trace, Output, tracedq[3]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_5_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_5_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_5_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_5_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_5_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_5_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_clk_for_lpbk- (QSPI Clock to be fed-back)*/ -#undef IOU_SLCR_MIO_PIN_6_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_6_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_6_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_6_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_6_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_6_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_6_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_6_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_6_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_6_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_6_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_6_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[6]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[6]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_6_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_6_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_6_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_6_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_6_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_6_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[6]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[6]- (GPIO bank 0) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, spi1 - sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, - Output, tracedq[4]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_6_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_6_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_6_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_6_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_6_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_6_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_n_ss_out_upper- (QSPI Slave Select upper)*/ -#undef IOU_SLCR_MIO_PIN_7_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_7_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_7_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_7_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_7_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_7_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_7_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_7_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_7_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_7_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_7_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_7_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[7]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[7]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_7_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_7_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_7_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_7_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_7_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_7_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[7]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[7]- (GPIO bank 0) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= - tc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, - racedq[5]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_7_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_7_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_7_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_7_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_7_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_7_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[0]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe - [0]- (QSPI Upper Databus)*/ -#undef IOU_SLCR_MIO_PIN_8_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_8_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_8_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_8_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_8_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_8_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_8_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_8_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_8_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_8_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_8_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_8_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[8]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[8]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_8_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_8_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_8_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_8_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_8_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_8_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[8]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[8]- (GPIO bank 0) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= ttc - , Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[6]- (Tr - ce Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_8_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_8_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_8_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_8_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_8_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_8_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[1]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe - [1]- (QSPI Upper Databus)*/ -#undef IOU_SLCR_MIO_PIN_9_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_9_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_9_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_9_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_9_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_9_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[1]- (NAND chip enable)*/ -#undef IOU_SLCR_MIO_PIN_9_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_9_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_9_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_9_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_9_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_9_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[9]- (Test Scan Port) = test_scan, Outp - t, test_scan_out[9]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_9_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_9_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_9_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_9_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_9_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_9_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[9]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[9]- (GPIO bank 0) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1, - utput, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (U - RT receiver serial input) 7= trace, Output, tracedq[7]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_9_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_9_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_9_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_9_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_9_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_9_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[2]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe - [2]- (QSPI Upper Databus)*/ -#undef IOU_SLCR_MIO_PIN_10_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_10_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_10_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_10_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_10_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_10_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[0]- (NAND Ready/Busy)*/ -#undef IOU_SLCR_MIO_PIN_10_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_10_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_10_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_10_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_10_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_10_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[10]- (Test Scan Port) = test_scan, Out - ut, test_scan_out[10]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_10_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_10_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_10_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_10_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_10_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_10_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[10]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[10]- (GPIO bank 0) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_ - o- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outp - t, tracedq[8]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_10_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_10_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_10_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_10_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_10_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_10_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Input, qspi_mi_upper[3]- (QSPI Upper Databus) 1= qspi, Output, qspi_mo_uppe - [3]- (QSPI Upper Databus)*/ -#undef IOU_SLCR_MIO_PIN_11_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_11_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_11_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_11_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_11_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_11_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[1]- (NAND Ready/Busy)*/ -#undef IOU_SLCR_MIO_PIN_11_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_11_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_11_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_11_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_11_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_11_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[11]- (Test Scan Port) = test_scan, Out - ut, test_scan_out[11]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_11_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_11_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_11_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_11_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_11_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_11_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[11]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[11]- (GPIO bank 0) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s - i1_si- (MOSI signal) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o - tput) 7= trace, Output, tracedq[9]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_11_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_11_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_11_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_11_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_11_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_11_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= qspi, Output, qspi_sclk_out_upper- (QSPI Upper Clock)*/ -#undef IOU_SLCR_MIO_PIN_12_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_12_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_12_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_12_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_12_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_12_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dqs_in- (NAND Strobe) 1= nand, Output, nfc_dqs_out- (NAND Strobe - */ -#undef IOU_SLCR_MIO_PIN_12_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_12_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_12_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_12_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_12_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_12_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= test_scan, Input, test_scan_in[12]- (Test Scan Port) = test_scan, Out - ut, test_scan_out[12]- (Test Scan Port) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_12_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_12_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_12_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_12_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_12_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_12_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[12]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[12]- (GPIO bank 0) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Cl - ck) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, trac - dq[10]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_12_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_12_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_12_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_12_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_12_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_12_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_13_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_13_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_13_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_13_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_13_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_13_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[0]- (NAND chip enable)*/ -#undef IOU_SLCR_MIO_PIN_13_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_13_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_13_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_13_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_13_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_13_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]- (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[13]- (Test Scan Port) = test_scan, Output, test_scan_out[13]- (Test Scan Port - 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_13_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_13_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_13_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_13_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_13_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_13_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[13]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[13]- (GPIO bank 0) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave - out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, tracedq[11]- (Trace Port Dat - bus)*/ -#undef IOU_SLCR_MIO_PIN_13_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_13_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_13_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_13_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_13_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_13_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_14_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_14_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_14_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_14_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_14_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_14_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_cle- (NAND Command Latch Enable)*/ -#undef IOU_SLCR_MIO_PIN_14_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_14_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_14_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_14_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_14_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_14_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]- (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[14]- (Test Scan Port) = test_scan, Output, test_scan_out[14]- (Test Scan Port - 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_14_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_14_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_14_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_14_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_14_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_14_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[14]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[14]- (GPIO bank 0) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc0, Input, ttc0_clk_ - n- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_14_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_14_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_14_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_14_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_14_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_14_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_15_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_15_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_15_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_15_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_15_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_15_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ale- (NAND Address Latch Enable)*/ -#undef IOU_SLCR_MIO_PIN_15_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_15_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_15_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_15_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_15_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_15_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]- (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[15]- (Test Scan Port) = test_scan, Output, test_scan_out[15]- (Test Scan Port - 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_15_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_15_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_15_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_15_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_15_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_15_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[15]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[15]- (GPIO bank 0) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out - 0]- (SPI Master Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter seri - l output) 7= trace, Output, tracedq[13]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_15_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_15_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_15_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_15_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_15_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_15_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_16_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_16_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_16_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_16_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_16_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_16_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[0]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[0]- (NAND - ata Bus)*/ -#undef IOU_SLCR_MIO_PIN_16_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_16_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_16_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_16_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_16_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_16_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]- (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[16]- (Test Scan Port) = test_scan, Output, test_scan_out[16]- (Test Scan Port - 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_16_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_16_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_16_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_16_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_16_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_16_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[16]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[16]- (GPIO bank 0) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0 - so- (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace - Output, tracedq[14]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_16_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_16_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_16_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_16_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_16_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_16_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_17_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_17_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_17_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_17_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_17_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_17_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[1]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[1]- (NAND - ata Bus)*/ -#undef IOU_SLCR_MIO_PIN_17_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_17_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_17_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_17_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_17_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_17_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]- (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[17]- (Test Scan Port) = test_scan, Output, test_scan_out[17]- (Test Scan Port - 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_17_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_17_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_17_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_17_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_17_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_17_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[17]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[17]- (GPIO bank 0) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, sp - 0_si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) - 7= trace, Output, tracedq[15]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_17_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_17_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_17_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_17_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_17_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_17_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_18_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_18_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_18_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_18_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_18_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_18_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[2]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[2]- (NAND - ata Bus)*/ -#undef IOU_SLCR_MIO_PIN_18_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_18_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_18_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_18_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_18_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_18_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]- (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[18]- (Test Scan Port) = test_scan, Output, test_scan_out[18]- (Test Scan Port - 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)*/ -#undef IOU_SLCR_MIO_PIN_18_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_18_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_18_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_18_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_18_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_18_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[18]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[18]- (GPIO bank 0) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_ - o- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_18_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_18_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_18_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_18_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_18_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_18_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_19_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_19_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_19_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_19_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_19_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_19_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[3]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[3]- (NAND - ata Bus)*/ -#undef IOU_SLCR_MIO_PIN_19_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_19_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_19_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_19_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_19_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_19_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]- (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[19]- (Test Scan Port) = test_scan, Output, test_scan_out[19]- (Test Scan Port - 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)*/ -#undef IOU_SLCR_MIO_PIN_19_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_19_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_19_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_19_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_19_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_19_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[19]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[19]- (GPIO bank 0) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5 - ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_19_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_19_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_19_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_19_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_19_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_19_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_20_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_20_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_20_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_20_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_20_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_20_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[4]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[4]- (NAND - ata Bus)*/ -#undef IOU_SLCR_MIO_PIN_20_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_20_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_20_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_20_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_20_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_20_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]- (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8 - bit Data bus) 2= test_scan, Input, test_scan_in[20]- (Test Scan Port) = test_scan, Output, test_scan_out[20]- (Test Scan Port - 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)*/ -#undef IOU_SLCR_MIO_PIN_20_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_20_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_20_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_20_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_20_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_20_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[20]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[20]- (GPIO bank 0) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= t - c1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_20_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_20_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_20_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_20_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_20_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_20_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_21_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_21_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_21_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_21_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_21_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_21_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[5]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[5]- (NAND - ata Bus)*/ -#undef IOU_SLCR_MIO_PIN_21_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_21_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_21_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_21_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_21_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_21_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Command Indicator) = sd0, Output, sdio0_cmd_out- (Comman - Indicator) 2= test_scan, Input, test_scan_in[21]- (Test Scan Port) = test_scan, Output, test_scan_out[21]- (Test Scan Port) - = csu, Input, csu_ext_tamper- (CSU Ext Tamper)*/ -#undef IOU_SLCR_MIO_PIN_21_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_21_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_21_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_21_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_21_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_21_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[21]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[21]- (GPIO bank 0) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1 - Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- - UART receiver serial input) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_21_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_21_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_21_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_21_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_21_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_21_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_22_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_22_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_22_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_22_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_22_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_22_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_we_b- (NAND Write Enable)*/ -#undef IOU_SLCR_MIO_PIN_22_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_22_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_22_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_22_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_22_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_22_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out- (SDSDIO clock) 2= test_scan, Input, test_scan_in[22]- - (Test Scan Port) = test_scan, Output, test_scan_out[22]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)*/ -#undef IOU_SLCR_MIO_PIN_22_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_22_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_22_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_22_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_22_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_22_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[22]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[22]- (GPIO bank 0) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, sp - 1_sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not - sed*/ -#undef IOU_SLCR_MIO_PIN_22_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_22_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_22_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_22_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_22_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_22_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_23_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_23_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_23_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_23_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_23_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_23_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[6]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[6]- (NAND - ata Bus)*/ -#undef IOU_SLCR_MIO_PIN_23_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_23_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_23_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_23_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_23_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_23_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow- (SD card bus power) 2= test_scan, Input, test_scan_in - 23]- (Test Scan Port) = test_scan, Output, test_scan_out[23]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper - */ -#undef IOU_SLCR_MIO_PIN_23_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_23_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_23_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_23_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_23_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_23_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[23]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[23]- (GPIO bank 0) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s - i1_si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o - tput) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_23_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_23_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_23_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_23_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_23_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_23_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_24_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_24_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_24_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_24_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_24_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_24_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dq_in[7]- (NAND Data Bus) 1= nand, Output, nfc_dq_out[7]- (NAND - ata Bus)*/ -#undef IOU_SLCR_MIO_PIN_24_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_24_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_24_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_24_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_24_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_24_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD card detect from connector) 2= test_scan, Input, test - scan_in[24]- (Test Scan Port) = test_scan, Output, test_scan_out[24]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ex - Tamper)*/ -#undef IOU_SLCR_MIO_PIN_24_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_24_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_24_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_24_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_24_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_24_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[24]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[24]- (GPIO bank 0) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= Not Used 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, - Output, ua1_txd- (UART transmitter serial output) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_24_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_24_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_24_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_24_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_24_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_24_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_25_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_25_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_25_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_25_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_25_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_25_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_re_n- (NAND Read Enable)*/ -#undef IOU_SLCR_MIO_PIN_25_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_25_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_25_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_25_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_25_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_25_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD card write protect from connector) 2= test_scan, Input, - test_scan_in[25]- (Test Scan Port) = test_scan, Output, test_scan_out[25]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (C - U Ext Tamper)*/ -#undef IOU_SLCR_MIO_PIN_25_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_25_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_25_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_25_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_25_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_25_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio0, Input, gpio_0_pin_in[25]- (GPIO bank 0) 0= gpio0, Output, gpio_0_pin_out[25]- (GPIO bank 0) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= Not Used 5= ttc3, Output, ttc3_wave_out- (TTC Waveform - lock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_25_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_25_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_25_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_25_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_25_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_25_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_tx_clk- (TX RGMII clock)*/ -#undef IOU_SLCR_MIO_PIN_26_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_26_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_26_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_26_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_26_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_26_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Output, nfc_ce[1]- (NAND chip enable)*/ -#undef IOU_SLCR_MIO_PIN_26_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_26_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_26_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_26_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_26_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_26_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[0]- (PMU GPI) 2= test_scan, Input, test_scan_in[26]- (Test Sc - n Port) = test_scan, Output, test_scan_out[26]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)*/ -#undef IOU_SLCR_MIO_PIN_26_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_26_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_26_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_26_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_26_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_26_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[0]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[0]- (GPIO bank 1) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Clock - 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[4]- - Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_26_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_26_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_26_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_26_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_26_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_26_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[0]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_27_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_27_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_27_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_27_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_27_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_27_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[0]- (NAND Ready/Busy)*/ -#undef IOU_SLCR_MIO_PIN_27_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_27_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_27_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_27_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_27_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_27_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[1]- (PMU GPI) 2= test_scan, Input, test_scan_in[27]- (Test Sc - n Port) = test_scan, Output, test_scan_out[27]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Outp - t, dp_aux_data_out- (Dp Aux Data)*/ -#undef IOU_SLCR_MIO_PIN_27_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_27_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_27_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_27_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_27_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_27_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[1]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[1]- (GPIO bank 1) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_ - ut- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, tracedq[5]- (Trace Port - atabus)*/ -#undef IOU_SLCR_MIO_PIN_27_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_27_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_27_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_27_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_27_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_27_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[1]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_28_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_28_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_28_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_28_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_28_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_28_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_rb_n[1]- (NAND Ready/Busy)*/ -#undef IOU_SLCR_MIO_PIN_28_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_28_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_28_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_28_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_28_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_28_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[2]- (PMU GPI) 2= test_scan, Input, test_scan_in[28]- (Test Sc - n Port) = test_scan, Output, test_scan_out[28]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug)*/ -#undef IOU_SLCR_MIO_PIN_28_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_28_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_28_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_28_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_28_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_28_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[2]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[2]- (GPIO bank 1) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc1, Input, ttc1_clk_i - - (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[6]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_28_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_28_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_28_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_28_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_28_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_28_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[2]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_29_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_29_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_29_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_29_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_29_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_29_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)*/ -#undef IOU_SLCR_MIO_PIN_29_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_29_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_29_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_29_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_29_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_29_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[3]- (PMU GPI) 2= test_scan, Input, test_scan_in[29]- (Test Sc - n Port) = test_scan, Output, test_scan_out[29]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Outp - t, dp_aux_data_out- (Dp Aux Data)*/ -#undef IOU_SLCR_MIO_PIN_29_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_29_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_29_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_29_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_29_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_29_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[3]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[3]- (GPIO bank 1) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[0] - (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial inpu - ) 7= trace, Output, tracedq[7]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_29_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_29_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_29_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_29_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_29_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_29_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_txd[3]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_30_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_30_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_30_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_30_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_30_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_30_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)*/ -#undef IOU_SLCR_MIO_PIN_30_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_30_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_30_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_30_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_30_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_30_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[4]- (PMU GPI) 2= test_scan, Input, test_scan_in[30]- (Test Sc - n Port) = test_scan, Output, test_scan_out[30]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug)*/ -#undef IOU_SLCR_MIO_PIN_30_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_30_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_30_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_30_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_30_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_30_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[4]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[4]- (GPIO bank 1) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_so - (MISO signal) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output - tracedq[8]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_30_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_30_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_30_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_30_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_30_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_30_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Output, gem0_rgmii_tx_ctl- (TX RGMII control)*/ -#undef IOU_SLCR_MIO_PIN_31_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_31_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_31_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_31_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_31_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_31_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)*/ -#undef IOU_SLCR_MIO_PIN_31_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_31_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_31_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_31_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_31_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_31_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Input, pmu_gpi[5]- (PMU GPI) 2= test_scan, Input, test_scan_in[31]- (Test Sc - n Port) = test_scan, Output, test_scan_out[31]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)*/ -#undef IOU_SLCR_MIO_PIN_31_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_31_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_31_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_31_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_31_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_31_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[5]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[5]- (GPIO bank 1) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, spi - _si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial out - ut) 7= trace, Output, tracedq[9]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_31_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_31_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_31_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_31_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_31_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_31_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rx_clk- (RX RGMII clock)*/ -#undef IOU_SLCR_MIO_PIN_32_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_32_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_32_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_32_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_32_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_32_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= nand, Input, nfc_dqs_in- (NAND Strobe) 1= nand, Output, nfc_dqs_out- (NAND Strobe - */ -#undef IOU_SLCR_MIO_PIN_32_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_32_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_32_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_32_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_32_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_32_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[0]- (PMU GPI) 2= test_scan, Input, test_scan_in[32]- (Test S - an Port) = test_scan, Output, test_scan_out[32]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)*/ -#undef IOU_SLCR_MIO_PIN_32_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_32_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_32_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_32_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_32_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_32_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[6]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[6]- (GPIO bank 1) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, spi - _sclk_out- (SPI Clock) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= - race, Output, tracedq[10]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_32_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_32_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_32_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_32_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_32_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_32_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[0]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_33_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_33_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_33_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_33_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_33_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_33_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)*/ -#undef IOU_SLCR_MIO_PIN_33_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_33_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_33_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_33_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_33_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_33_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[1]- (PMU GPI) 2= test_scan, Input, test_scan_in[33]- (Test S - an Port) = test_scan, Output, test_scan_out[33]- (Test Scan Port) 3= csu, Input, csu_ext_tamper- (CSU Ext Tamper)*/ -#undef IOU_SLCR_MIO_PIN_33_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_33_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_33_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_33_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_33_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_33_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[7]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[7]- (GPIO bank 1) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= t - c3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, traced - [11]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_33_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_33_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_33_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_33_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_33_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_33_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[1]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_34_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_34_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_34_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_34_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_34_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_34_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)*/ -#undef IOU_SLCR_MIO_PIN_34_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_34_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_34_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_34_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_34_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_34_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[2]- (PMU GPI) 2= test_scan, Input, test_scan_in[34]- (Test S - an Port) = test_scan, Output, test_scan_out[34]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Out - ut, dp_aux_data_out- (Dp Aux Data)*/ -#undef IOU_SLCR_MIO_PIN_34_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_34_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_34_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_34_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_34_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_34_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[8]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[8]- (GPIO bank 1) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= ttc2 - Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace P - rt Databus)*/ -#undef IOU_SLCR_MIO_PIN_34_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_34_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_34_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_34_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_34_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_34_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[2]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_35_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_35_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_35_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_35_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_35_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_35_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)*/ -#undef IOU_SLCR_MIO_PIN_35_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_35_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_35_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_35_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_35_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_35_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[3]- (PMU GPI) 2= test_scan, Input, test_scan_in[35]- (Test S - an Port) = test_scan, Output, test_scan_out[35]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug)*/ -#undef IOU_SLCR_MIO_PIN_35_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_35_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_35_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_35_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_35_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_35_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[9]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[9]- (GPIO bank 1) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1, - Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- - UART transmitter serial output) 7= trace, Output, tracedq[13]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_35_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_35_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_35_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_35_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_35_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_35_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rxd[3]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_36_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_36_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_36_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_36_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_36_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_36_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)*/ -#undef IOU_SLCR_MIO_PIN_36_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_36_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_36_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_36_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_36_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_36_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[4]- (PMU GPI) 2= test_scan, Input, test_scan_in[36]- (Test S - an Port) = test_scan, Output, test_scan_out[36]- (Test Scan Port) 3= dpaux, Input, dp_aux_data_in- (Dp Aux Data) = dpaux, Out - ut, dp_aux_data_out- (Dp Aux Data)*/ -#undef IOU_SLCR_MIO_PIN_36_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_36_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_36_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_36_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_36_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_36_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[10]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[10]- (GPIO bank 1) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1 - so- (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace - Output, tracedq[14]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_36_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_36_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_36_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_36_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_36_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_36_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem0, Input, gem0_rgmii_rx_ctl- (RX RGMII control )*/ -#undef IOU_SLCR_MIO_PIN_37_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_37_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_37_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_37_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_37_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_37_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= pcie, Input, pcie_reset_n- (PCIE Reset signal)*/ -#undef IOU_SLCR_MIO_PIN_37_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_37_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_37_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_37_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_37_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_37_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= pmu, Output, pmu_gpo[5]- (PMU GPI) 2= test_scan, Input, test_scan_in[37]- (Test S - an Port) = test_scan, Output, test_scan_out[37]- (Test Scan Port) 3= dpaux, Input, dp_hot_plug_detect- (Dp Aux Hot Plug)*/ -#undef IOU_SLCR_MIO_PIN_37_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_37_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_37_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_37_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_37_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_37_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[11]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[11]- (GPIO bank 1) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, sp - 1_si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) - 7= trace, Output, tracedq[15]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_37_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_37_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_37_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_37_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_37_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_37_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_tx_clk- (TX RGMII clock)*/ -#undef IOU_SLCR_MIO_PIN_38_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_38_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_38_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_38_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_38_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_38_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_38_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_38_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_38_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_38_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_38_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_38_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out- (SDSDIO clock) 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_38_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_38_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_38_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_38_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_38_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_38_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[12]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[12]- (GPIO bank 1) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Clo - k) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, trace_clk- - (Trace Port Clock)*/ -#undef IOU_SLCR_MIO_PIN_38_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_38_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_38_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_38_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_38_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_38_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[0]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_39_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_39_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_39_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_39_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_39_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_39_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_39_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_39_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_39_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_39_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_39_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_39_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD card detect from connector) 2= sd1, Input, sd1_data_i - [4]- (8-bit Data bus) = sd1, Output, sdio1_data_out[4]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_39_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_39_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_39_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_39_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_39_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_39_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[13]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[13]- (GPIO bank 1) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc0, Output, ttc0_wav - _out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, trace_ctl- (Trace Port - Control Signal)*/ -#undef IOU_SLCR_MIO_PIN_39_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_39_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_39_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_39_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_39_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_39_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[1]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_40_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_40_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_40_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_40_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_40_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_40_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_40_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_40_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_40_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_40_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_40_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_40_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Command Indicator) = sd0, Output, sdio0_cmd_out- (Comman - Indicator) 2= sd1, Input, sd1_data_in[5]- (8-bit Data bus) = sd1, Output, sdio1_data_out[5]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_40_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_40_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_40_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_40_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_40_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_40_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[14]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[14]- (GPIO bank 1) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc3, Input, ttc3_clk - in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[0]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_40_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_40_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_40_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_40_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_40_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_40_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[2]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_41_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_41_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_41_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_41_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_41_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_41_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_41_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_41_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_41_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_41_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_41_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_41_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]- (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[6]- (8-bit Data bus) = sd1, Output, sdio1_data_out[6]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_41_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_41_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_41_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_41_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_41_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_41_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[15]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[15]- (GPIO bank 1) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[ - ]- (SPI Master Selects) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial in - ut) 7= trace, Output, tracedq[1]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_41_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_41_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_41_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_41_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_41_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_41_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_txd[3]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_42_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_42_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_42_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_42_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_42_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_42_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_42_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_42_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_42_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_42_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_42_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_42_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]- (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[7]- (8-bit Data bus) = sd1, Output, sdio1_data_out[7]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_42_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_42_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_42_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_42_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_42_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_42_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[16]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[16]- (GPIO bank 1) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_ - o- (MISO signal) 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outp - t, tracedq[2]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_42_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_42_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_42_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_42_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_42_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_42_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Output, gem1_rgmii_tx_ctl- (TX RGMII control)*/ -#undef IOU_SLCR_MIO_PIN_43_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_43_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_43_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_43_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_43_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_43_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_43_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_43_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_43_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_43_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_43_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_43_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]- (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8 - bit Data bus) 2= sd1, Output, sdio1_bus_pow- (SD card bus power) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_43_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_43_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_43_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_43_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_43_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_43_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[17]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[17]- (GPIO bank 1) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, s - i0_si- (MOSI signal) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o - tput) 7= trace, Output, tracedq[3]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_43_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_43_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_43_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_43_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_43_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_43_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rx_clk- (RX RGMII clock)*/ -#undef IOU_SLCR_MIO_PIN_44_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_44_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_44_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_44_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_44_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_44_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_44_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_44_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_44_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_44_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_44_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_44_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]- (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8 - bit Data bus) 2= sd1, Input, sdio1_wp- (SD card write protect from connector) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_44_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_44_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_44_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_44_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_44_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_44_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[18]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[18]- (GPIO bank 1) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, s - i1_sclk_out- (SPI Clock) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7 - Not Used*/ -#undef IOU_SLCR_MIO_PIN_44_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_44_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_44_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_44_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_44_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_44_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[0]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_45_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_45_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_45_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_45_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_45_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_45_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_45_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_45_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_45_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_45_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_45_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_45_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]- (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8 - bit Data bus) 2= sd1, Input, sdio1_cd_n- (SD card detect from connector) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_45_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_45_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_45_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_45_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_45_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_45_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[19]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[19]- (GPIO bank 1) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= - ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_45_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_45_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_45_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_45_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_45_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_45_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[1]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_46_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_46_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_46_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_46_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_46_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_46_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_46_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_46_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_46_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_46_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_46_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_46_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]- (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[0]- (8-bit Data bus) = sd1, Output, sdio1_data_out[0]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_46_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_46_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_46_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_46_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_46_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_46_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[20]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[20]- (GPIO bank 1) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= tt - 0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_46_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_46_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_46_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_46_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_46_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_46_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[2]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_47_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_47_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_47_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_47_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_47_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_47_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_47_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_47_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_47_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_47_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_47_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_47_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]- (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[1]- (8-bit Data bus) = sd1, Output, sdio1_data_out[1]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_47_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_47_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_47_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_47_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_47_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_47_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[21]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[21]- (GPIO bank 1) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi - , Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd - (UART transmitter serial output) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_47_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_47_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_47_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_47_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_47_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_47_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rxd[3]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_48_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_48_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_48_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_48_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_48_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_48_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_48_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_48_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_48_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_48_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_48_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_48_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]- (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[2]- (8-bit Data bus) = sd1, Output, sdio1_data_out[2]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_48_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_48_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_48_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_48_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_48_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_48_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[22]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[22]- (GPIO bank 1) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1 - so- (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= Not U - ed*/ -#undef IOU_SLCR_MIO_PIN_48_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_48_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_48_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_48_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_48_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_48_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem1, Input, gem1_rgmii_rx_ctl- (RX RGMII control )*/ -#undef IOU_SLCR_MIO_PIN_49_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_49_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_49_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_49_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_49_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_49_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_49_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_49_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_49_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_49_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_49_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_49_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow- (SD card bus power) 2= sd1, Input, sd1_data_in[3]- (8 - bit Data bus) = sd1, Output, sdio1_data_out[3]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_49_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_49_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_49_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_49_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_49_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_49_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[23]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[23]- (GPIO bank 1) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, sp - 1_si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) - 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_49_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_49_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_49_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_49_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_49_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_49_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem_tsu, Input, gem_tsu_clk- (TSU clock)*/ -#undef IOU_SLCR_MIO_PIN_50_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_50_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_50_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_50_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_50_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_50_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_50_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_50_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_50_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_50_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_50_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_50_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD card write protect from connector) 2= sd1, Input, sd1_c - d_in- (Command Indicator) = sd1, Output, sdio1_cmd_out- (Command Indicator) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_50_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_50_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_50_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_50_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_50_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_50_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[24]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[24]- (GPIO bank 1) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= mdio1, Output, gem1_mdc- (MDIO Clock) 5= ttc2, Input, ttc2 - clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_50_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_50_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_50_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_50_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_50_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_50_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem_tsu, Input, gem_tsu_clk- (TSU clock)*/ -#undef IOU_SLCR_MIO_PIN_51_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_51_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_51_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_51_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_51_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_51_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_51_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_51_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_51_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_51_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_51_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_51_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= sd1, Output, sdio1_clk_out- (SDSDIO clock) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_51_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_51_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_51_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_51_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_51_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_51_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio1, Input, gpio_1_pin_in[25]- (GPIO bank 1) 0= gpio1, Output, gpio_1_pin_out[25]- (GPIO bank 1) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= mdio1, Input, gem1_mdio_in- (MDIO Data) 4= mdio1, Outp - t, gem1_mdio_out- (MDIO Data) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter - serial output) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_51_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_51_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_51_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_51_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_51_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_51_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_tx_clk- (TX RGMII clock)*/ -#undef IOU_SLCR_MIO_PIN_52_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_52_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_52_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_52_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_52_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_52_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_clk_in- (ULPI Clock)*/ -#undef IOU_SLCR_MIO_PIN_52_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_52_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_52_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_52_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_52_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_52_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_52_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_52_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_52_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_52_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_52_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_52_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[0]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[0]- (GPIO bank 2) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, spi0_sclk_out- (SPI Cloc - ) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, trace_ - lk- (Trace Port Clock)*/ -#undef IOU_SLCR_MIO_PIN_52_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_52_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_52_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_52_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_52_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_52_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[0]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_53_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_53_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_53_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_53_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_53_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_53_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_dir- (Data bus direction control)*/ -#undef IOU_SLCR_MIO_PIN_53_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_53_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_53_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_53_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_53_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_53_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_53_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_53_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_53_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_53_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_53_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_53_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[1]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[1]- (GPIO bank 2) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= ttc1, Output, ttc1_wave_o - t- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, trace_ctl- (Trace Port Control - Signal)*/ -#undef IOU_SLCR_MIO_PIN_53_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_53_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_53_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_53_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_53_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_53_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[1]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_54_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_54_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_54_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_54_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_54_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_54_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[2]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[2]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_54_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_54_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_54_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_54_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_54_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_54_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_54_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_54_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_54_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_54_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_54_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_54_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[2]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[2]- (GPIO bank 2) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= ttc0, Input, ttc0_clk_in - (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[0]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_54_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_54_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_54_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_54_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_54_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_54_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[2]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_55_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_55_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_55_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_55_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_55_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_55_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_nxt- (Data flow control signal from the PHY)*/ -#undef IOU_SLCR_MIO_PIN_55_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_55_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_55_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_55_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_55_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_55_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_55_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_55_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_55_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_55_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_55_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_55_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[3]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[3]- (GPIO bank 2) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi0, Output, spi0_n_ss_out[0 - - (SPI Master Selects) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial - output) 7= trace, Output, tracedq[1]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_55_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_55_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_55_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_55_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_55_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_55_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_txd[3]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_56_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_56_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_56_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_56_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_56_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_56_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[0]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[0]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_56_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_56_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_56_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_56_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_56_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_56_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_56_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_56_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_56_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_56_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_56_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_56_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[4]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[4]- (GPIO bank 2) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0_s - - (MISO signal) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, - utput, tracedq[2]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_56_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_56_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_56_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_56_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_56_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_56_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Output, gem2_rgmii_tx_ctl- (TX RGMII control)*/ -#undef IOU_SLCR_MIO_PIN_57_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_57_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_57_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_57_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_57_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_57_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[1]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[1]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_57_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_57_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_57_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_57_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_57_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_57_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_57_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_57_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_57_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_57_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_57_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_57_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[5]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[5]- (GPIO bank 2) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, spi0 - si- (MOSI signal) 5= ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7 - trace, Output, tracedq[3]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_57_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_57_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_57_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_57_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_57_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_57_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rx_clk- (RX RGMII clock)*/ -#undef IOU_SLCR_MIO_PIN_58_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_58_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_58_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_58_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_58_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_58_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Output, usb0_ulpi_stp- (Asserted to end or interrupt transfers)*/ -#undef IOU_SLCR_MIO_PIN_58_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_58_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_58_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_58_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_58_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_58_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_58_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_58_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_58_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_58_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_58_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_58_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[6]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[6]- (GPIO bank 2) 1= can - , Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL signal - 3= pjtag, Input, pjtag_tck- (PJTAG TCK) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, spi1_sclk_out- (SPI Clock - 5= ttc2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[4]- - Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_58_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_58_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_58_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_58_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_58_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_58_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[0]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_59_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_59_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_59_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_59_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_59_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_59_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[3]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[3]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_59_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_59_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_59_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_59_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_59_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_59_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_59_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_59_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_59_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_59_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_59_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_59_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[7]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[7]- (GPIO bank 2) 1= can - , Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA signa - ) 3= pjtag, Input, pjtag_tdi- (PJTAG TDI) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_ - ut- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= trace, Output, tracedq[5]- (Trace Port - atabus)*/ -#undef IOU_SLCR_MIO_PIN_59_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_59_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_59_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_59_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_59_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_59_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[1]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_60_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_60_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_60_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_60_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_60_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_60_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[4]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[4]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_60_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_60_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_60_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_60_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_60_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_60_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_60_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_60_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_60_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_60_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_60_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_60_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[8]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[8]- (GPIO bank 2) 1= can - , Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL signa - ) 3= pjtag, Output, pjtag_tdo- (PJTAG TDO) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= ttc1, Input, ttc1_clk_i - - (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace, Output, tracedq[6]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_60_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_60_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_60_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_60_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_60_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_60_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[2]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_61_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_61_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_61_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_61_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_61_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_61_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[5]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[5]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_61_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_61_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_61_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_61_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_61_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_61_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_61_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_61_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_61_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_61_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_61_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_61_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[9]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[9]- (GPIO bank 2) 1= can - , Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA signal - 3= pjtag, Input, pjtag_tms- (PJTAG TMS) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1, Output, spi1_n_ss_out[0] - (SPI Master Selects) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial inpu - ) 7= trace, Output, tracedq[7]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_61_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_61_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_61_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_61_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_61_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_61_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rxd[3]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_62_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_62_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_62_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_62_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_62_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_62_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[6]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[6]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_62_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_62_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_62_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_62_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_62_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_62_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_62_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_62_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_62_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_62_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_62_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_62_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[10]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[10]- (GPIO bank 2) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_ - o- (MISO signal) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Outp - t, tracedq[8]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_62_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_62_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_62_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_62_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_62_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_62_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem2, Input, gem2_rgmii_rx_ctl- (RX RGMII control )*/ -#undef IOU_SLCR_MIO_PIN_63_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_63_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_63_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_63_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_63_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_63_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb0, Input, usb0_ulpi_rx_data[7]- (ULPI data bus) 1= usb0, Output, usb0_ulpi_tx_ - ata[7]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_63_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_63_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_63_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_63_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_63_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_63_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_63_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_63_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_63_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_63_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_63_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_63_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[11]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[11]- (GPIO bank 2) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s - i1_si- (MOSI signal) 5= ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial o - tput) 7= trace, Output, tracedq[9]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_63_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_63_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_63_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_63_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_63_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_63_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_tx_clk- (TX RGMII clock)*/ -#undef IOU_SLCR_MIO_PIN_64_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_64_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_64_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_64_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_64_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_64_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_clk_in- (ULPI Clock)*/ -#undef IOU_SLCR_MIO_PIN_64_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_64_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_64_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_64_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_64_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_64_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_clk_out- (SDSDIO clock) 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_64_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_64_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_64_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_64_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_64_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_64_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[12]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[12]- (GPIO bank 2) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_sclk_in- (SPI Clock) 4= spi0, Output, s - i0_sclk_out- (SPI Clock) 5= ttc3, Input, ttc3_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7 - trace, Output, tracedq[10]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_64_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_64_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_64_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_64_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_64_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_64_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[0]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_65_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_65_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_65_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_65_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_65_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_65_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_dir- (Data bus direction control)*/ -#undef IOU_SLCR_MIO_PIN_65_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_65_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_65_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_65_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_65_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_65_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_cd_n- (SD card detect from connector) 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_65_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_65_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_65_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_65_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_65_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_65_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[13]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[13]- (GPIO bank 2) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_n_ss_out[2]- (SPI Master Selects) 5= - ttc3, Output, ttc3_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= trace, Output, trac - dq[11]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_65_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_65_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_65_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_65_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_65_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_65_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[1]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_66_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_66_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_66_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_66_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_66_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_66_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[2]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[2]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_66_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_66_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_66_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_66_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_66_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_66_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_cmd_in- (Command Indicator) = sd0, Output, sdio0_cmd_out- (Comman - Indicator) 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_66_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_66_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_66_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_66_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_66_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_66_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[14]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[14]- (GPIO bank 2) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi0, Output, spi0_n_ss_out[1]- (SPI Master Selects) 5= tt - 2, Input, ttc2_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= trace, Output, tracedq[12]- (Trace - Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_66_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_66_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_66_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_66_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_66_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_66_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[2]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_67_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_67_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_67_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_67_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_67_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_67_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_nxt- (Data flow control signal from the PHY)*/ -#undef IOU_SLCR_MIO_PIN_67_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_67_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_67_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_67_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_67_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_67_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[0]- (8-bit Data bus) = sd0, Output, sdio0_data_out[0]- (8 - bit Data bus) 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_67_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_67_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_67_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_67_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_67_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_67_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[15]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[15]- (GPIO bank 2) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi0, Input, spi0_n_ss_in- (SPI Master Selects) 4= spi - , Output, spi0_n_ss_out[0]- (SPI Master Selects) 5= ttc2, Output, ttc2_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd - (UART transmitter serial output) 7= trace, Output, tracedq[13]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_67_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_67_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_67_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_67_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_67_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_67_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_txd[3]- (TX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_68_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_68_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_68_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_68_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_68_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_68_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[0]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[0]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_68_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_68_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_68_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_68_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_68_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_68_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[1]- (8-bit Data bus) = sd0, Output, sdio0_data_out[1]- (8 - bit Data bus) 2= Not Used 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_68_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_68_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_68_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_68_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_68_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_68_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[16]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[16]- (GPIO bank 2) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi0, Input, spi0_mi- (MISO signal) 4= spi0, Output, spi0 - so- (MISO signal) 5= ttc1, Input, ttc1_clk_in- (TTC Clock) 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= trace - Output, tracedq[14]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_68_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_68_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_68_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_68_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_68_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_68_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Output, gem3_rgmii_tx_ctl- (TX RGMII control)*/ -#undef IOU_SLCR_MIO_PIN_69_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_69_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_69_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_69_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_69_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_69_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[1]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[1]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_69_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_69_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_69_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_69_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_69_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_69_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[2]- (8-bit Data bus) = sd0, Output, sdio0_data_out[2]- (8 - bit Data bus) 2= sd1, Input, sdio1_wp- (SD card write protect from connector) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_69_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_69_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_69_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_69_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_69_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_69_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[17]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[17]- (GPIO bank 2) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi0, Output, spi0_mo- (MOSI signal) 4= spi0, Input, sp - 0_si- (MOSI signal) 5= ttc1, Output, ttc1_wave_out- (TTC Waveform Clock) 6= ua1, Input, ua1_rxd- (UART receiver serial input) - 7= trace, Output, tracedq[15]- (Trace Port Databus)*/ -#undef IOU_SLCR_MIO_PIN_69_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_69_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_69_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_69_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_69_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_69_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rx_clk- (RX RGMII clock)*/ -#undef IOU_SLCR_MIO_PIN_70_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_70_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_70_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_70_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_70_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_70_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Output, usb1_ulpi_stp- (Asserted to end or interrupt transfers)*/ -#undef IOU_SLCR_MIO_PIN_70_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_70_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_70_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_70_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_70_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_70_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[3]- (8-bit Data bus) = sd0, Output, sdio0_data_out[3]- (8 - bit Data bus) 2= sd1, Output, sdio1_bus_pow- (SD card bus power) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_70_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_70_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_70_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_70_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_70_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_70_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[18]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[18]- (GPIO bank 2) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_sclk_in- (SPI Clock) 4= spi1, Output, sp - 1_sclk_out- (SPI Clock) 5= ttc0, Input, ttc0_clk_in- (TTC Clock) 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not - sed*/ -#undef IOU_SLCR_MIO_PIN_70_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_70_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_70_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_70_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_70_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_70_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[0]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_71_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_71_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_71_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_71_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_71_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_71_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[3]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[3]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_71_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_71_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_71_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_71_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_71_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_71_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[4]- (8-bit Data bus) = sd0, Output, sdio0_data_out[4]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[0]- (8-bit Data bus) = sd1, Output, sdio1_data_out[0]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_71_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_71_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_71_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_71_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_71_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_71_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[19]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[19]- (GPIO bank 2) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_n_ss_out[2]- (SPI Master Selects) 5 - ttc0, Output, ttc0_wave_out- (TTC Waveform Clock) 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_71_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_71_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_71_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_71_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_71_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_71_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[1]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_72_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_72_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_72_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_72_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_72_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_72_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[4]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[4]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_72_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_72_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_72_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_72_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_72_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_72_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[5]- (8-bit Data bus) = sd0, Output, sdio0_data_out[5]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[1]- (8-bit Data bus) = sd1, Output, sdio1_data_out[1]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_72_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_72_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_72_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_72_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_72_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_72_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[20]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[20]- (GPIO bank 2) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= swdt1, Input, swdt1_clk_in- (Watch Dog Timer Input clock) 4= spi1, Output, spi1_n_ss_out[1]- (SPI Master Selects) 5= N - t Used 6= ua1, Output, ua1_txd- (UART transmitter serial output) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_72_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_72_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_72_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_72_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_72_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_72_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[2]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_73_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_73_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_73_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_73_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_73_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_73_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[5]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[5]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_73_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_73_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_73_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_73_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_73_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_73_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[6]- (8-bit Data bus) = sd0, Output, sdio0_data_out[6]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[2]- (8-bit Data bus) = sd1, Output, sdio1_data_out[2]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_73_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_73_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_73_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_73_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_73_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_73_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[21]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[21]- (GPIO bank 2) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= swdt1, Output, swdt1_rst_out- (Watch Dog Timer Output clock) 4= spi1, Input, spi1_n_ss_in- (SPI Master Selects) 4= spi1 - Output, spi1_n_ss_out[0]- (SPI Master Selects) 5= Not Used 6= ua1, Input, ua1_rxd- (UART receiver serial input) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_73_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_73_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_73_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_73_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_73_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_73_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rxd[3]- (RX RGMII data)*/ -#undef IOU_SLCR_MIO_PIN_74_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_74_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_74_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_74_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_74_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_74_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[6]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[6]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_74_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_74_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_74_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_74_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_74_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_74_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sd0_data_in[7]- (8-bit Data bus) = sd0, Output, sdio0_data_out[7]- (8 - bit Data bus) 2= sd1, Input, sd1_data_in[3]- (8-bit Data bus) = sd1, Output, sdio1_data_out[3]- (8-bit Data bus) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_74_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_74_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_74_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_74_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_74_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_74_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[22]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[22]- (GPIO bank 2) 1= c - n0, Input, can0_phy_rx- (Can RX signal) 2= i2c0, Input, i2c0_scl_input- (SCL signal) 2= i2c0, Output, i2c0_scl_out- (SCL sign - l) 3= swdt0, Input, swdt0_clk_in- (Watch Dog Timer Input clock) 4= spi1, Input, spi1_mi- (MISO signal) 4= spi1, Output, spi1_ - o- (MISO signal) 5= Not Used 6= ua0, Input, ua0_rxd- (UART receiver serial input) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_74_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_74_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_74_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_74_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_74_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_74_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= gem3, Input, gem3_rgmii_rx_ctl- (RX RGMII control )*/ -#undef IOU_SLCR_MIO_PIN_75_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_75_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_75_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_75_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_75_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_75_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= usb1, Input, usb1_ulpi_rx_data[7]- (ULPI data bus) 1= usb1, Output, usb1_ulpi_tx_ - ata[7]- (ULPI data bus)*/ -#undef IOU_SLCR_MIO_PIN_75_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_75_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_75_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_75_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_75_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_75_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Output, sdio0_bus_pow- (SD card bus power) 2= sd1, Input, sd1_cmd_in- (Comma - d Indicator) = sd1, Output, sdio1_cmd_out- (Command Indicator) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_75_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_75_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_75_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_75_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_75_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_75_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[23]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[23]- (GPIO bank 2) 1= c - n0, Output, can0_phy_tx- (Can TX signal) 2= i2c0, Input, i2c0_sda_input- (SDA signal) 2= i2c0, Output, i2c0_sda_out- (SDA sig - al) 3= swdt0, Output, swdt0_rst_out- (Watch Dog Timer Output clock) 4= spi1, Output, spi1_mo- (MOSI signal) 4= spi1, Input, s - i1_si- (MOSI signal) 5= Not Used 6= ua0, Output, ua0_txd- (UART transmitter serial output) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_75_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_75_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_75_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_75_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_75_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_75_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_76_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_76_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_76_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_76_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_76_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_76_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_76_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_76_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_76_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_76_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_76_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_76_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= sd0, Input, sdio0_wp- (SD card write protect from connector) 2= sd1, Output, sdio - _clk_out- (SDSDIO clock) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_76_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_76_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_76_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_76_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_76_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_76_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[24]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[24]- (GPIO bank 2) 1= c - n1, Output, can1_phy_tx- (Can TX signal) 2= i2c1, Input, i2c1_scl_input- (SCL signal) 2= i2c1, Output, i2c1_scl_out- (SCL sig - al) 3= mdio0, Output, gem0_mdc- (MDIO Clock) 4= mdio1, Output, gem1_mdc- (MDIO Clock) 5= mdio2, Output, gem2_mdc- (MDIO Clock - 6= mdio3, Output, gem3_mdc- (MDIO Clock) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_76_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_76_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_76_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_76_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_76_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_76_L3_SEL_MASK 0x000000E0U - -/*Level 0 Mux Select 0= Level 1 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_77_L0_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_77_L0_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_77_L0_SEL_MASK -#define IOU_SLCR_MIO_PIN_77_L0_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_77_L0_SEL_SHIFT 1 -#define IOU_SLCR_MIO_PIN_77_L0_SEL_MASK 0x00000002U - -/*Level 1 Mux Select 0= Level 2 Mux Output 1= Not Used*/ -#undef IOU_SLCR_MIO_PIN_77_L1_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_77_L1_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_77_L1_SEL_MASK -#define IOU_SLCR_MIO_PIN_77_L1_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_77_L1_SEL_SHIFT 2 -#define IOU_SLCR_MIO_PIN_77_L1_SEL_MASK 0x00000004U - -/*Level 2 Mux Select 0= Level 3 Mux Output 1= Not Used 2= sd1, Input, sdio1_cd_n- (SD card detect from connector) 3= Not Used*/ -#undef IOU_SLCR_MIO_PIN_77_L2_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_77_L2_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_77_L2_SEL_MASK -#define IOU_SLCR_MIO_PIN_77_L2_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_77_L2_SEL_SHIFT 3 -#define IOU_SLCR_MIO_PIN_77_L2_SEL_MASK 0x00000018U - -/*Level 3 Mux Select 0= gpio2, Input, gpio_2_pin_in[25]- (GPIO bank 2) 0= gpio2, Output, gpio_2_pin_out[25]- (GPIO bank 2) 1= c - n1, Input, can1_phy_rx- (Can RX signal) 2= i2c1, Input, i2c1_sda_input- (SDA signal) 2= i2c1, Output, i2c1_sda_out- (SDA sign - l) 3= mdio0, Input, gem0_mdio_in- (MDIO Data) 3= mdio0, Output, gem0_mdio_out- (MDIO Data) 4= mdio1, Input, gem1_mdio_in- (MD - O Data) 4= mdio1, Output, gem1_mdio_out- (MDIO Data) 5= mdio2, Input, gem2_mdio_in- (MDIO Data) 5= mdio2, Output, gem2_mdio_o - t- (MDIO Data) 6= mdio3, Input, gem3_mdio_in- (MDIO Data) 6= mdio3, Output, gem3_mdio_out- (MDIO Data) 7= Not Used*/ -#undef IOU_SLCR_MIO_PIN_77_L3_SEL_DEFVAL -#undef IOU_SLCR_MIO_PIN_77_L3_SEL_SHIFT -#undef IOU_SLCR_MIO_PIN_77_L3_SEL_MASK -#define IOU_SLCR_MIO_PIN_77_L3_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_PIN_77_L3_SEL_SHIFT 5 -#define IOU_SLCR_MIO_PIN_77_L3_SEL_MASK 0x000000E0U - -/*Master Tri-state Enable for pin 0, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI_SHIFT 0 -#define IOU_SLCR_MIO_MST_TRI0_PIN_00_TRI_MASK 0x00000001U - -/*Master Tri-state Enable for pin 1, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI_SHIFT 1 -#define IOU_SLCR_MIO_MST_TRI0_PIN_01_TRI_MASK 0x00000002U - -/*Master Tri-state Enable for pin 2, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI_SHIFT 2 -#define IOU_SLCR_MIO_MST_TRI0_PIN_02_TRI_MASK 0x00000004U - -/*Master Tri-state Enable for pin 3, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI_SHIFT 3 -#define IOU_SLCR_MIO_MST_TRI0_PIN_03_TRI_MASK 0x00000008U - -/*Master Tri-state Enable for pin 4, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI_SHIFT 4 -#define IOU_SLCR_MIO_MST_TRI0_PIN_04_TRI_MASK 0x00000010U - -/*Master Tri-state Enable for pin 5, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI_SHIFT 5 -#define IOU_SLCR_MIO_MST_TRI0_PIN_05_TRI_MASK 0x00000020U - -/*Master Tri-state Enable for pin 6, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI_SHIFT 6 -#define IOU_SLCR_MIO_MST_TRI0_PIN_06_TRI_MASK 0x00000040U - -/*Master Tri-state Enable for pin 7, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI_SHIFT 7 -#define IOU_SLCR_MIO_MST_TRI0_PIN_07_TRI_MASK 0x00000080U - -/*Master Tri-state Enable for pin 8, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI_SHIFT 8 -#define IOU_SLCR_MIO_MST_TRI0_PIN_08_TRI_MASK 0x00000100U - -/*Master Tri-state Enable for pin 9, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI_SHIFT 9 -#define IOU_SLCR_MIO_MST_TRI0_PIN_09_TRI_MASK 0x00000200U - -/*Master Tri-state Enable for pin 10, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI_SHIFT 10 -#define IOU_SLCR_MIO_MST_TRI0_PIN_10_TRI_MASK 0x00000400U - -/*Master Tri-state Enable for pin 11, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI_SHIFT 11 -#define IOU_SLCR_MIO_MST_TRI0_PIN_11_TRI_MASK 0x00000800U - -/*Master Tri-state Enable for pin 12, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI_SHIFT 12 -#define IOU_SLCR_MIO_MST_TRI0_PIN_12_TRI_MASK 0x00001000U - -/*Master Tri-state Enable for pin 13, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI_SHIFT 13 -#define IOU_SLCR_MIO_MST_TRI0_PIN_13_TRI_MASK 0x00002000U - -/*Master Tri-state Enable for pin 14, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI_SHIFT 14 -#define IOU_SLCR_MIO_MST_TRI0_PIN_14_TRI_MASK 0x00004000U - -/*Master Tri-state Enable for pin 15, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI_SHIFT 15 -#define IOU_SLCR_MIO_MST_TRI0_PIN_15_TRI_MASK 0x00008000U - -/*Master Tri-state Enable for pin 16, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI_SHIFT 16 -#define IOU_SLCR_MIO_MST_TRI0_PIN_16_TRI_MASK 0x00010000U - -/*Master Tri-state Enable for pin 17, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI_SHIFT 17 -#define IOU_SLCR_MIO_MST_TRI0_PIN_17_TRI_MASK 0x00020000U - -/*Master Tri-state Enable for pin 18, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI_SHIFT 18 -#define IOU_SLCR_MIO_MST_TRI0_PIN_18_TRI_MASK 0x00040000U - -/*Master Tri-state Enable for pin 19, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI_SHIFT 19 -#define IOU_SLCR_MIO_MST_TRI0_PIN_19_TRI_MASK 0x00080000U - -/*Master Tri-state Enable for pin 20, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI_SHIFT 20 -#define IOU_SLCR_MIO_MST_TRI0_PIN_20_TRI_MASK 0x00100000U - -/*Master Tri-state Enable for pin 21, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI_SHIFT 21 -#define IOU_SLCR_MIO_MST_TRI0_PIN_21_TRI_MASK 0x00200000U - -/*Master Tri-state Enable for pin 22, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI_SHIFT 22 -#define IOU_SLCR_MIO_MST_TRI0_PIN_22_TRI_MASK 0x00400000U - -/*Master Tri-state Enable for pin 23, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI_SHIFT 23 -#define IOU_SLCR_MIO_MST_TRI0_PIN_23_TRI_MASK 0x00800000U - -/*Master Tri-state Enable for pin 24, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI_SHIFT 24 -#define IOU_SLCR_MIO_MST_TRI0_PIN_24_TRI_MASK 0x01000000U - -/*Master Tri-state Enable for pin 25, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI_SHIFT 25 -#define IOU_SLCR_MIO_MST_TRI0_PIN_25_TRI_MASK 0x02000000U - -/*Master Tri-state Enable for pin 26, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI_SHIFT 26 -#define IOU_SLCR_MIO_MST_TRI0_PIN_26_TRI_MASK 0x04000000U - -/*Master Tri-state Enable for pin 27, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI_SHIFT 27 -#define IOU_SLCR_MIO_MST_TRI0_PIN_27_TRI_MASK 0x08000000U - -/*Master Tri-state Enable for pin 28, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI_SHIFT 28 -#define IOU_SLCR_MIO_MST_TRI0_PIN_28_TRI_MASK 0x10000000U - -/*Master Tri-state Enable for pin 29, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI_SHIFT 29 -#define IOU_SLCR_MIO_MST_TRI0_PIN_29_TRI_MASK 0x20000000U - -/*Master Tri-state Enable for pin 30, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI_SHIFT 30 -#define IOU_SLCR_MIO_MST_TRI0_PIN_30_TRI_MASK 0x40000000U - -/*Master Tri-state Enable for pin 31, active high*/ -#undef IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI_SHIFT 31 -#define IOU_SLCR_MIO_MST_TRI0_PIN_31_TRI_MASK 0x80000000U - -/*Master Tri-state Enable for pin 32, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI_SHIFT 0 -#define IOU_SLCR_MIO_MST_TRI1_PIN_32_TRI_MASK 0x00000001U - -/*Master Tri-state Enable for pin 33, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI_SHIFT 1 -#define IOU_SLCR_MIO_MST_TRI1_PIN_33_TRI_MASK 0x00000002U - -/*Master Tri-state Enable for pin 34, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI_SHIFT 2 -#define IOU_SLCR_MIO_MST_TRI1_PIN_34_TRI_MASK 0x00000004U - -/*Master Tri-state Enable for pin 35, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI_SHIFT 3 -#define IOU_SLCR_MIO_MST_TRI1_PIN_35_TRI_MASK 0x00000008U - -/*Master Tri-state Enable for pin 36, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI_SHIFT 4 -#define IOU_SLCR_MIO_MST_TRI1_PIN_36_TRI_MASK 0x00000010U - -/*Master Tri-state Enable for pin 37, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI_SHIFT 5 -#define IOU_SLCR_MIO_MST_TRI1_PIN_37_TRI_MASK 0x00000020U - -/*Master Tri-state Enable for pin 38, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI_SHIFT 6 -#define IOU_SLCR_MIO_MST_TRI1_PIN_38_TRI_MASK 0x00000040U - -/*Master Tri-state Enable for pin 39, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI_SHIFT 7 -#define IOU_SLCR_MIO_MST_TRI1_PIN_39_TRI_MASK 0x00000080U - -/*Master Tri-state Enable for pin 40, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI_SHIFT 8 -#define IOU_SLCR_MIO_MST_TRI1_PIN_40_TRI_MASK 0x00000100U - -/*Master Tri-state Enable for pin 41, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI_SHIFT 9 -#define IOU_SLCR_MIO_MST_TRI1_PIN_41_TRI_MASK 0x00000200U - -/*Master Tri-state Enable for pin 42, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI_SHIFT 10 -#define IOU_SLCR_MIO_MST_TRI1_PIN_42_TRI_MASK 0x00000400U - -/*Master Tri-state Enable for pin 43, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI_SHIFT 11 -#define IOU_SLCR_MIO_MST_TRI1_PIN_43_TRI_MASK 0x00000800U - -/*Master Tri-state Enable for pin 44, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI_SHIFT 12 -#define IOU_SLCR_MIO_MST_TRI1_PIN_44_TRI_MASK 0x00001000U - -/*Master Tri-state Enable for pin 45, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI_SHIFT 13 -#define IOU_SLCR_MIO_MST_TRI1_PIN_45_TRI_MASK 0x00002000U - -/*Master Tri-state Enable for pin 46, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI_SHIFT 14 -#define IOU_SLCR_MIO_MST_TRI1_PIN_46_TRI_MASK 0x00004000U - -/*Master Tri-state Enable for pin 47, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI_SHIFT 15 -#define IOU_SLCR_MIO_MST_TRI1_PIN_47_TRI_MASK 0x00008000U - -/*Master Tri-state Enable for pin 48, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI_SHIFT 16 -#define IOU_SLCR_MIO_MST_TRI1_PIN_48_TRI_MASK 0x00010000U - -/*Master Tri-state Enable for pin 49, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI_SHIFT 17 -#define IOU_SLCR_MIO_MST_TRI1_PIN_49_TRI_MASK 0x00020000U - -/*Master Tri-state Enable for pin 50, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI_SHIFT 18 -#define IOU_SLCR_MIO_MST_TRI1_PIN_50_TRI_MASK 0x00040000U - -/*Master Tri-state Enable for pin 51, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI_SHIFT 19 -#define IOU_SLCR_MIO_MST_TRI1_PIN_51_TRI_MASK 0x00080000U - -/*Master Tri-state Enable for pin 52, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI_SHIFT 20 -#define IOU_SLCR_MIO_MST_TRI1_PIN_52_TRI_MASK 0x00100000U - -/*Master Tri-state Enable for pin 53, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI_SHIFT 21 -#define IOU_SLCR_MIO_MST_TRI1_PIN_53_TRI_MASK 0x00200000U - -/*Master Tri-state Enable for pin 54, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI_SHIFT 22 -#define IOU_SLCR_MIO_MST_TRI1_PIN_54_TRI_MASK 0x00400000U - -/*Master Tri-state Enable for pin 55, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI_SHIFT 23 -#define IOU_SLCR_MIO_MST_TRI1_PIN_55_TRI_MASK 0x00800000U - -/*Master Tri-state Enable for pin 56, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI_SHIFT 24 -#define IOU_SLCR_MIO_MST_TRI1_PIN_56_TRI_MASK 0x01000000U - -/*Master Tri-state Enable for pin 57, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI_SHIFT 25 -#define IOU_SLCR_MIO_MST_TRI1_PIN_57_TRI_MASK 0x02000000U - -/*Master Tri-state Enable for pin 58, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI_SHIFT 26 -#define IOU_SLCR_MIO_MST_TRI1_PIN_58_TRI_MASK 0x04000000U - -/*Master Tri-state Enable for pin 59, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI_SHIFT 27 -#define IOU_SLCR_MIO_MST_TRI1_PIN_59_TRI_MASK 0x08000000U - -/*Master Tri-state Enable for pin 60, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI_SHIFT 28 -#define IOU_SLCR_MIO_MST_TRI1_PIN_60_TRI_MASK 0x10000000U - -/*Master Tri-state Enable for pin 61, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI_SHIFT 29 -#define IOU_SLCR_MIO_MST_TRI1_PIN_61_TRI_MASK 0x20000000U - -/*Master Tri-state Enable for pin 62, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI_SHIFT 30 -#define IOU_SLCR_MIO_MST_TRI1_PIN_62_TRI_MASK 0x40000000U - -/*Master Tri-state Enable for pin 63, active high*/ -#undef IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI_DEFVAL 0xFFFFFFFF -#define IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI_SHIFT 31 -#define IOU_SLCR_MIO_MST_TRI1_PIN_63_TRI_MASK 0x80000000U - -/*Master Tri-state Enable for pin 64, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI_SHIFT 0 -#define IOU_SLCR_MIO_MST_TRI2_PIN_64_TRI_MASK 0x00000001U - -/*Master Tri-state Enable for pin 65, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI_SHIFT 1 -#define IOU_SLCR_MIO_MST_TRI2_PIN_65_TRI_MASK 0x00000002U - -/*Master Tri-state Enable for pin 66, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI_SHIFT 2 -#define IOU_SLCR_MIO_MST_TRI2_PIN_66_TRI_MASK 0x00000004U - -/*Master Tri-state Enable for pin 67, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI_SHIFT 3 -#define IOU_SLCR_MIO_MST_TRI2_PIN_67_TRI_MASK 0x00000008U - -/*Master Tri-state Enable for pin 68, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI_SHIFT 4 -#define IOU_SLCR_MIO_MST_TRI2_PIN_68_TRI_MASK 0x00000010U - -/*Master Tri-state Enable for pin 69, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI_SHIFT 5 -#define IOU_SLCR_MIO_MST_TRI2_PIN_69_TRI_MASK 0x00000020U - -/*Master Tri-state Enable for pin 70, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI_SHIFT 6 -#define IOU_SLCR_MIO_MST_TRI2_PIN_70_TRI_MASK 0x00000040U - -/*Master Tri-state Enable for pin 71, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI_SHIFT 7 -#define IOU_SLCR_MIO_MST_TRI2_PIN_71_TRI_MASK 0x00000080U - -/*Master Tri-state Enable for pin 72, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI_SHIFT 8 -#define IOU_SLCR_MIO_MST_TRI2_PIN_72_TRI_MASK 0x00000100U - -/*Master Tri-state Enable for pin 73, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI_SHIFT 9 -#define IOU_SLCR_MIO_MST_TRI2_PIN_73_TRI_MASK 0x00000200U - -/*Master Tri-state Enable for pin 74, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI_SHIFT 10 -#define IOU_SLCR_MIO_MST_TRI2_PIN_74_TRI_MASK 0x00000400U - -/*Master Tri-state Enable for pin 75, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI_SHIFT 11 -#define IOU_SLCR_MIO_MST_TRI2_PIN_75_TRI_MASK 0x00000800U - -/*Master Tri-state Enable for pin 76, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI_SHIFT 12 -#define IOU_SLCR_MIO_MST_TRI2_PIN_76_TRI_MASK 0x00001000U - -/*Master Tri-state Enable for pin 77, active high*/ -#undef IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI_DEFVAL -#undef IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI_SHIFT -#undef IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI_MASK -#define IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI_DEFVAL 0x00003FFF -#define IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI_SHIFT 13 -#define IOU_SLCR_MIO_MST_TRI2_PIN_77_TRI_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25_DEFVAL -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25_SHIFT -#undef IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25_MASK -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25_DEFVAL -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK0_CTRL0_DRIVE0_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25_DEFVAL -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25_SHIFT -#undef IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25_MASK -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25_DEFVAL -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK0_CTRL1_DRIVE1_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25_DEFVAL -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25_SHIFT -#undef IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25_MASK -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25_DEFVAL -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK0_CTRL3_SCHMITT_CMOS_N_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25_DEFVAL -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25_SHIFT -#undef IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25_MASK -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25_DEFVAL -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK0_CTRL4_PULL_HIGH_LOW_N_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25_DEFVAL -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25_SHIFT -#undef IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25_MASK -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25_DEFVAL -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK0_CTRL5_PULL_ENABLE_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[0].*/ -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25_DEFVAL -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25_SHIFT -#undef IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25_MASK -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25_DEFVAL -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK0_CTRL6_SLOW_FAST_SLEW_N_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25_DEFVAL -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25_SHIFT -#undef IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25_MASK -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25_DEFVAL -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK1_CTRL0_DRIVE0_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25_DEFVAL -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25_SHIFT -#undef IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25_MASK -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25_DEFVAL -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK1_CTRL1_DRIVE1_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25_DEFVAL -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25_SHIFT -#undef IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25_MASK -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25_DEFVAL -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK1_CTRL3_SCHMITT_CMOS_N_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25_DEFVAL -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25_SHIFT -#undef IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25_MASK -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25_DEFVAL -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK1_CTRL4_PULL_HIGH_LOW_N_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0_SHIFT 12 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_0_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1_SHIFT 13 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_1_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2_SHIFT 14 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_2_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3_SHIFT 15 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_3_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4_SHIFT 16 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_4_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5_SHIFT 17 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_5_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6_SHIFT 18 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_6_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7_SHIFT 19 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_7_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8_SHIFT 20 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_8_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9_SHIFT 21 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_9_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10_SHIFT 22 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_10_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11_SHIFT 23 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_11_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12_SHIFT 24 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_12_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13_SHIFT 25 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_13_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14_SHIFT 0 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_14_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15_SHIFT 1 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_15_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16_SHIFT 2 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_16_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17_SHIFT 3 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_17_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18_SHIFT 4 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_18_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19_SHIFT 5 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_19_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20_SHIFT 6 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_20_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21_SHIFT 7 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_21_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22_SHIFT 8 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_22_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23_SHIFT 9 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_23_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24_SHIFT 10 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_24_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25_DEFVAL -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25_SHIFT -#undef IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25_MASK -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25_DEFVAL -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25_SHIFT 11 -#define IOU_SLCR_BANK1_CTRL5_PULL_ENABLE_BIT_25_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[26].*/ -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25_DEFVAL -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25_SHIFT -#undef IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25_MASK -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25_DEFVAL -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK1_CTRL6_SLOW_FAST_SLEW_N_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25_DEFVAL -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25_SHIFT -#undef IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25_MASK -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25_DEFVAL -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK2_CTRL0_DRIVE0_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25_DEFVAL -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25_SHIFT -#undef IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25_MASK -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25_DEFVAL -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK2_CTRL1_DRIVE1_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25_DEFVAL -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25_SHIFT -#undef IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25_MASK -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25_DEFVAL -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK2_CTRL3_SCHMITT_CMOS_N_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25_DEFVAL -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25_SHIFT -#undef IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25_MASK -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25_DEFVAL -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK2_CTRL4_PULL_HIGH_LOW_N_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25_DEFVAL -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25_SHIFT -#undef IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25_MASK -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25_DEFVAL -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK2_CTRL5_PULL_ENABLE_BIT_25_MASK 0x02000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0_SHIFT 0 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_0_MASK 0x00000001U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1_SHIFT 1 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_1_MASK 0x00000002U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2_SHIFT 2 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_2_MASK 0x00000004U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3_SHIFT 3 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_3_MASK 0x00000008U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4_SHIFT 4 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_4_MASK 0x00000010U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5_SHIFT 5 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_5_MASK 0x00000020U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6_SHIFT 6 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_6_MASK 0x00000040U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7_SHIFT 7 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_7_MASK 0x00000080U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8_SHIFT 8 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_8_MASK 0x00000100U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9_SHIFT 9 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_9_MASK 0x00000200U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10_SHIFT 10 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_10_MASK 0x00000400U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11_SHIFT 11 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_11_MASK 0x00000800U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12_SHIFT 12 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_12_MASK 0x00001000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13_SHIFT 13 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_13_MASK 0x00002000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14_SHIFT 14 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_14_MASK 0x00004000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15_SHIFT 15 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_15_MASK 0x00008000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16_SHIFT 16 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_16_MASK 0x00010000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17_SHIFT 17 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_17_MASK 0x00020000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18_SHIFT 18 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_18_MASK 0x00040000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19_SHIFT 19 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_19_MASK 0x00080000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20_SHIFT 20 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_20_MASK 0x00100000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21_SHIFT 21 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_21_MASK 0x00200000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22_SHIFT 22 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_22_MASK 0x00400000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23_SHIFT 23 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_23_MASK 0x00800000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24_SHIFT 24 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_24_MASK 0x01000000U - -/*Each bit applies to a single IO. Bit 0 for MIO[52].*/ -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25_DEFVAL -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25_SHIFT -#undef IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25_MASK -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25_DEFVAL -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25_SHIFT 25 -#define IOU_SLCR_BANK2_CTRL6_SLOW_FAST_SLEW_N_BIT_25_MASK 0x02000000U - -/*I2C Loopback Control. 0 = Connect I2C inputs according to MIO mapping. 1 = Loop I2C 0 outputs to I2C 1 inputs, and I2C 1 outp - ts to I2C 0 inputs.*/ -#undef IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1_DEFVAL -#undef IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1_SHIFT -#undef IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1_MASK -#define IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1_SHIFT 3 -#define IOU_SLCR_MIO_LOOPBACK_I2C0_LOOP_I2C1_MASK 0x00000008U - -/*CAN Loopback Control. 0 = Connect CAN inputs according to MIO mapping. 1 = Loop CAN 0 Tx to CAN 1 Rx, and CAN 1 Tx to CAN 0 R - .*/ -#undef IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1_DEFVAL -#undef IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1_SHIFT -#undef IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1_MASK -#define IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1_SHIFT 2 -#define IOU_SLCR_MIO_LOOPBACK_CAN0_LOOP_CAN1_MASK 0x00000004U - -/*UART Loopback Control. 0 = Connect UART inputs according to MIO mapping. 1 = Loop UART 0 outputs to UART 1 inputs, and UART 1 - outputs to UART 0 inputs. RXD/TXD cross-connected. RTS/CTS cross-connected. DSR, DTR, DCD and RI not used.*/ -#undef IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1_DEFVAL -#undef IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1_SHIFT -#undef IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1_MASK -#define IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1_SHIFT 1 -#define IOU_SLCR_MIO_LOOPBACK_UA0_LOOP_UA1_MASK 0x00000002U - -/*SPI Loopback Control. 0 = Connect SPI inputs according to MIO mapping. 1 = Loop SPI 0 outputs to SPI 1 inputs, and SPI 1 outp - ts to SPI 0 inputs. The other SPI core will appear on the LS Slave Select.*/ -#undef IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1_DEFVAL -#undef IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1_SHIFT -#undef IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1_MASK -#define IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1_DEFVAL 0x00000000 -#define IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1_SHIFT 0 -#define IOU_SLCR_MIO_LOOPBACK_SPI0_LOOP_SPI1_MASK 0x00000001U -#undef CRL_APB_RST_LPD_IOU2_OFFSET -#define CRL_APB_RST_LPD_IOU2_OFFSET 0XFF5E0238 -#undef CRL_APB_RST_LPD_IOU0_OFFSET -#define CRL_APB_RST_LPD_IOU0_OFFSET 0XFF5E0230 -#undef CRL_APB_RST_LPD_IOU2_OFFSET -#define CRL_APB_RST_LPD_IOU2_OFFSET 0XFF5E0238 -#undef IOU_SLCR_IOU_TAPDLY_BYPASS_OFFSET -#define IOU_SLCR_IOU_TAPDLY_BYPASS_OFFSET 0XFF180390 -#undef CRL_APB_RST_LPD_TOP_OFFSET -#define CRL_APB_RST_LPD_TOP_OFFSET 0XFF5E023C -#undef CRF_APB_RST_FPD_TOP_OFFSET -#define CRF_APB_RST_FPD_TOP_OFFSET 0XFD1A0100 -#undef CRL_APB_RST_LPD_IOU2_OFFSET -#define CRL_APB_RST_LPD_IOU2_OFFSET 0XFF5E0238 -#undef IOU_SLCR_CTRL_REG_SD_OFFSET -#define IOU_SLCR_CTRL_REG_SD_OFFSET 0XFF180310 -#undef IOU_SLCR_SD_CONFIG_REG2_OFFSET -#define IOU_SLCR_SD_CONFIG_REG2_OFFSET 0XFF180320 -#undef IOU_SLCR_SD_CONFIG_REG1_OFFSET -#define IOU_SLCR_SD_CONFIG_REG1_OFFSET 0XFF18031C -#undef IOU_SLCR_SD_CONFIG_REG3_OFFSET -#define IOU_SLCR_SD_CONFIG_REG3_OFFSET 0XFF180324 -#undef CRL_APB_RST_LPD_IOU2_OFFSET -#define CRL_APB_RST_LPD_IOU2_OFFSET 0XFF5E0238 -#undef CRL_APB_RST_LPD_IOU2_OFFSET -#define CRL_APB_RST_LPD_IOU2_OFFSET 0XFF5E0238 -#undef CRL_APB_RST_LPD_IOU2_OFFSET -#define CRL_APB_RST_LPD_IOU2_OFFSET 0XFF5E0238 -#undef CRL_APB_RST_LPD_IOU2_OFFSET -#define CRL_APB_RST_LPD_IOU2_OFFSET 0XFF5E0238 -#undef CRL_APB_RST_LPD_IOU2_OFFSET -#define CRL_APB_RST_LPD_IOU2_OFFSET 0XFF5E0238 -#undef TPIU_LAR_OFFSET -#define TPIU_LAR_OFFSET 0XFE980FB0 -#undef TPIU_CURRENT_PORT_SIZE_OFFSET -#define TPIU_CURRENT_PORT_SIZE_OFFSET 0XFE980004 -#undef TPIU_LAR_OFFSET -#define TPIU_LAR_OFFSET 0XFE980FB0 -#undef UART0_BAUD_RATE_DIVIDER_REG0_OFFSET -#define UART0_BAUD_RATE_DIVIDER_REG0_OFFSET 0XFF000034 -#undef UART0_BAUD_RATE_GEN_REG0_OFFSET -#define UART0_BAUD_RATE_GEN_REG0_OFFSET 0XFF000018 -#undef UART0_CONTROL_REG0_OFFSET -#define UART0_CONTROL_REG0_OFFSET 0XFF000000 -#undef UART0_MODE_REG0_OFFSET -#define UART0_MODE_REG0_OFFSET 0XFF000004 -#undef UART1_BAUD_RATE_DIVIDER_REG0_OFFSET -#define UART1_BAUD_RATE_DIVIDER_REG0_OFFSET 0XFF010034 -#undef UART1_BAUD_RATE_GEN_REG0_OFFSET -#define UART1_BAUD_RATE_GEN_REG0_OFFSET 0XFF010018 -#undef UART1_CONTROL_REG0_OFFSET -#define UART1_CONTROL_REG0_OFFSET 0XFF010000 -#undef UART1_MODE_REG0_OFFSET -#define UART1_MODE_REG0_OFFSET 0XFF010004 -#undef LPD_SLCR_SECURE_SLCR_ADMA_OFFSET -#define LPD_SLCR_SECURE_SLCR_ADMA_OFFSET 0XFF4B0024 -#undef CSU_TAMPER_STATUS_OFFSET -#define CSU_TAMPER_STATUS_OFFSET 0XFFCA5000 -#undef APU_ACE_CTRL_OFFSET -#define APU_ACE_CTRL_OFFSET 0XFD5C0060 -#undef RTC_CONTROL_OFFSET -#define RTC_CONTROL_OFFSET 0XFFA60040 -#undef IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_OFFSET -#define IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_OFFSET 0XFF260020 -#undef IOU_SCNTRS_COUNTER_CONTROL_REGISTER_OFFSET -#define IOU_SCNTRS_COUNTER_CONTROL_REGISTER_OFFSET 0XFF260000 - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_TIMESTAMP_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_TIMESTAMP_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_TIMESTAMP_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_TIMESTAMP_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_TIMESTAMP_RESET_SHIFT 20 -#define CRL_APB_RST_LPD_IOU2_TIMESTAMP_RESET_MASK 0x00100000U - -/*GEM 3 reset*/ -#undef CRL_APB_RST_LPD_IOU0_GEM3_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU0_GEM3_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU0_GEM3_RESET_MASK -#define CRL_APB_RST_LPD_IOU0_GEM3_RESET_DEFVAL 0x0000000F -#define CRL_APB_RST_LPD_IOU0_GEM3_RESET_SHIFT 3 -#define CRL_APB_RST_LPD_IOU0_GEM3_RESET_MASK 0x00000008U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_QSPI_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_QSPI_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_QSPI_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_QSPI_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_QSPI_RESET_SHIFT 0 -#define CRL_APB_RST_LPD_IOU2_QSPI_RESET_MASK 0x00000001U - -/*0: Do not by pass the tap delays on the Rx clock signal of LQSPI 1: Bypass the Tap delay on the Rx clock signal of LQSPI*/ -#undef IOU_SLCR_IOU_TAPDLY_BYPASS_LQSPI_RX_DEFVAL -#undef IOU_SLCR_IOU_TAPDLY_BYPASS_LQSPI_RX_SHIFT -#undef IOU_SLCR_IOU_TAPDLY_BYPASS_LQSPI_RX_MASK -#define IOU_SLCR_IOU_TAPDLY_BYPASS_LQSPI_RX_DEFVAL 0x00000007 -#define IOU_SLCR_IOU_TAPDLY_BYPASS_LQSPI_RX_SHIFT 2 -#define IOU_SLCR_IOU_TAPDLY_BYPASS_LQSPI_RX_MASK 0x00000004U - -/*USB 0 reset for control registers*/ -#undef CRL_APB_RST_LPD_TOP_USB0_APB_RESET_DEFVAL -#undef CRL_APB_RST_LPD_TOP_USB0_APB_RESET_SHIFT -#undef CRL_APB_RST_LPD_TOP_USB0_APB_RESET_MASK -#define CRL_APB_RST_LPD_TOP_USB0_APB_RESET_DEFVAL 0x00188FDF -#define CRL_APB_RST_LPD_TOP_USB0_APB_RESET_SHIFT 10 -#define CRL_APB_RST_LPD_TOP_USB0_APB_RESET_MASK 0x00000400U - -/*USB 0 sleep circuit reset*/ -#undef CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_DEFVAL -#undef CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_SHIFT -#undef CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_MASK -#define CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_DEFVAL 0x00188FDF -#define CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_SHIFT 8 -#define CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_MASK 0x00000100U - -/*USB 0 reset*/ -#undef CRL_APB_RST_LPD_TOP_USB0_CORERESET_DEFVAL -#undef CRL_APB_RST_LPD_TOP_USB0_CORERESET_SHIFT -#undef CRL_APB_RST_LPD_TOP_USB0_CORERESET_MASK -#define CRL_APB_RST_LPD_TOP_USB0_CORERESET_DEFVAL 0x00188FDF -#define CRL_APB_RST_LPD_TOP_USB0_CORERESET_SHIFT 6 -#define CRL_APB_RST_LPD_TOP_USB0_CORERESET_MASK 0x00000040U - -/*Display Port block level reset (includes DPDMA)*/ -#undef CRF_APB_RST_FPD_TOP_DP_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_DP_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_DP_RESET_MASK -#define CRF_APB_RST_FPD_TOP_DP_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_DP_RESET_SHIFT 16 -#define CRF_APB_RST_FPD_TOP_DP_RESET_MASK 0x00010000U - -/*FPD WDT reset*/ -#undef CRF_APB_RST_FPD_TOP_SWDT_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_SWDT_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_SWDT_RESET_MASK -#define CRF_APB_RST_FPD_TOP_SWDT_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_SWDT_RESET_SHIFT 15 -#define CRF_APB_RST_FPD_TOP_SWDT_RESET_MASK 0x00008000U - -/*GDMA block level reset*/ -#undef CRF_APB_RST_FPD_TOP_GDMA_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_GDMA_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_GDMA_RESET_MASK -#define CRF_APB_RST_FPD_TOP_GDMA_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_GDMA_RESET_SHIFT 6 -#define CRF_APB_RST_FPD_TOP_GDMA_RESET_MASK 0x00000040U - -/*Pixel Processor (submodule of GPU) block level reset*/ -#undef CRF_APB_RST_FPD_TOP_GPU_PP0_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_GPU_PP0_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_GPU_PP0_RESET_MASK -#define CRF_APB_RST_FPD_TOP_GPU_PP0_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_GPU_PP0_RESET_SHIFT 4 -#define CRF_APB_RST_FPD_TOP_GPU_PP0_RESET_MASK 0x00000010U - -/*Pixel Processor (submodule of GPU) block level reset*/ -#undef CRF_APB_RST_FPD_TOP_GPU_PP1_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_GPU_PP1_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_GPU_PP1_RESET_MASK -#define CRF_APB_RST_FPD_TOP_GPU_PP1_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_GPU_PP1_RESET_SHIFT 5 -#define CRF_APB_RST_FPD_TOP_GPU_PP1_RESET_MASK 0x00000020U - -/*GPU block level reset*/ -#undef CRF_APB_RST_FPD_TOP_GPU_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_GPU_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_GPU_RESET_MASK -#define CRF_APB_RST_FPD_TOP_GPU_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_GPU_RESET_SHIFT 3 -#define CRF_APB_RST_FPD_TOP_GPU_RESET_MASK 0x00000008U - -/*GT block level reset*/ -#undef CRF_APB_RST_FPD_TOP_GT_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_GT_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_GT_RESET_MASK -#define CRF_APB_RST_FPD_TOP_GT_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_GT_RESET_SHIFT 2 -#define CRF_APB_RST_FPD_TOP_GT_RESET_MASK 0x00000004U - -/*Sata block level reset*/ -#undef CRF_APB_RST_FPD_TOP_SATA_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_SATA_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_SATA_RESET_MASK -#define CRF_APB_RST_FPD_TOP_SATA_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_SATA_RESET_SHIFT 1 -#define CRF_APB_RST_FPD_TOP_SATA_RESET_MASK 0x00000002U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_SDIO1_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_SDIO1_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_SDIO1_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_SDIO1_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_SDIO1_RESET_SHIFT 6 -#define CRL_APB_RST_LPD_IOU2_SDIO1_RESET_MASK 0x00000040U - -/*SD or eMMC selection on SDIO1 0: SD enabled 1: eMMC enabled*/ -#undef IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL_DEFVAL -#undef IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL_SHIFT -#undef IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL_MASK -#define IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL_DEFVAL 0x00000000 -#define IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL_SHIFT 15 -#define IOU_SLCR_CTRL_REG_SD_SD1_EMMC_SEL_MASK 0x00008000U - -/*Should be set based on the final product usage 00 - Removable SCard Slot 01 - Embedded Slot for One Device 10 - Shared Bus Sl - t 11 - Reserved*/ -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE_DEFVAL -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE_SHIFT -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE_MASK -#define IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE_DEFVAL 0x0FFC0FFC -#define IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE_SHIFT 28 -#define IOU_SLCR_SD_CONFIG_REG2_SD1_SLOTTYPE_MASK 0x30000000U - -/*1.8V Support 1: 1.8V supported 0: 1.8V not supported support*/ -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V_DEFVAL -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V_SHIFT -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V_MASK -#define IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V_DEFVAL 0x0FFC0FFC -#define IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V_SHIFT 25 -#define IOU_SLCR_SD_CONFIG_REG2_SD1_1P8V_MASK 0x02000000U - -/*3.0V Support 1: 3.0V supported 0: 3.0V not supported support*/ -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V_DEFVAL -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V_SHIFT -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V_MASK -#define IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V_DEFVAL 0x0FFC0FFC -#define IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V_SHIFT 24 -#define IOU_SLCR_SD_CONFIG_REG2_SD1_3P0V_MASK 0x01000000U - -/*3.3V Support 1: 3.3V supported 0: 3.3V not supported support*/ -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V_DEFVAL -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V_SHIFT -#undef IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V_MASK -#define IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V_DEFVAL 0x0FFC0FFC -#define IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V_SHIFT 23 -#define IOU_SLCR_SD_CONFIG_REG2_SD1_3P3V_MASK 0x00800000U - -/*Base Clock Frequency for SD Clock. This is the frequency of the xin_clk.*/ -#undef IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK_DEFVAL -#undef IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK_SHIFT -#undef IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK_MASK -#define IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK_DEFVAL 0x32403240 -#define IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK_SHIFT 23 -#define IOU_SLCR_SD_CONFIG_REG1_SD1_BASECLK_MASK 0x7F800000U - -/*This is the Timer Count for Re-Tuning Timer for Re-Tuning Mode 1 to 3. Setting to 4'b0 disables Re-Tuning Timer. 0h - Get inf - rmation via other source 1h = 1 seconds 2h = 2 seconds 3h = 4 seconds 4h = 8 seconds -- n = 2(n-1) seconds -- Bh = 1024 secon - s Fh - Ch = Reserved*/ -#undef IOU_SLCR_SD_CONFIG_REG3_SD1_RETUNETMR_DEFVAL -#undef IOU_SLCR_SD_CONFIG_REG3_SD1_RETUNETMR_SHIFT -#undef IOU_SLCR_SD_CONFIG_REG3_SD1_RETUNETMR_MASK -#define IOU_SLCR_SD_CONFIG_REG3_SD1_RETUNETMR_DEFVAL 0x06070607 -#define IOU_SLCR_SD_CONFIG_REG3_SD1_RETUNETMR_SHIFT 22 -#define IOU_SLCR_SD_CONFIG_REG3_SD1_RETUNETMR_MASK 0x03C00000U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_CAN1_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_CAN1_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_CAN1_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_CAN1_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_CAN1_RESET_SHIFT 8 -#define CRL_APB_RST_LPD_IOU2_CAN1_RESET_MASK 0x00000100U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_I2C0_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_I2C0_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_I2C0_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_I2C0_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_I2C0_RESET_SHIFT 9 -#define CRL_APB_RST_LPD_IOU2_I2C0_RESET_MASK 0x00000200U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_I2C1_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_I2C1_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_I2C1_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_I2C1_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_I2C1_RESET_SHIFT 10 -#define CRL_APB_RST_LPD_IOU2_I2C1_RESET_MASK 0x00000400U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_SWDT_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_SWDT_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_SWDT_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_SWDT_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_SWDT_RESET_SHIFT 15 -#define CRL_APB_RST_LPD_IOU2_SWDT_RESET_MASK 0x00008000U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_TTC0_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_TTC0_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_TTC0_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_TTC0_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_TTC0_RESET_SHIFT 11 -#define CRL_APB_RST_LPD_IOU2_TTC0_RESET_MASK 0x00000800U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_TTC1_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_TTC1_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_TTC1_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_TTC1_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_TTC1_RESET_SHIFT 12 -#define CRL_APB_RST_LPD_IOU2_TTC1_RESET_MASK 0x00001000U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_TTC2_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_TTC2_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_TTC2_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_TTC2_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_TTC2_RESET_SHIFT 13 -#define CRL_APB_RST_LPD_IOU2_TTC2_RESET_MASK 0x00002000U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_TTC3_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_TTC3_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_TTC3_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_TTC3_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_TTC3_RESET_SHIFT 14 -#define CRL_APB_RST_LPD_IOU2_TTC3_RESET_MASK 0x00004000U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_UART0_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_UART0_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_UART0_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_UART0_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_UART0_RESET_SHIFT 1 -#define CRL_APB_RST_LPD_IOU2_UART0_RESET_MASK 0x00000002U - -/*Block level reset*/ -#undef CRL_APB_RST_LPD_IOU2_UART1_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU2_UART1_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU2_UART1_RESET_MASK -#define CRL_APB_RST_LPD_IOU2_UART1_RESET_DEFVAL 0x0017FFFF -#define CRL_APB_RST_LPD_IOU2_UART1_RESET_SHIFT 2 -#define CRL_APB_RST_LPD_IOU2_UART1_RESET_MASK 0x00000004U - -/*A write of 0xC5ACCE55 enables further write access to this device. A write of any value other than 0xC5ACCE55 will have the a - fect of removing write access.*/ -#undef TPIU_LAR_ACCESS_W_DEFVAL -#undef TPIU_LAR_ACCESS_W_SHIFT -#undef TPIU_LAR_ACCESS_W_MASK -#define TPIU_LAR_ACCESS_W_DEFVAL -#define TPIU_LAR_ACCESS_W_SHIFT 0 -#define TPIU_LAR_ACCESS_W_MASK 0xFFFFFFFFU - -/*Indicates whether the current port size of the TPIU is 32 bits.*/ -#undef TPIU_CURRENT_PORT_SIZE_PORT_SIZE_32_DEFVAL -#undef TPIU_CURRENT_PORT_SIZE_PORT_SIZE_32_SHIFT -#undef TPIU_CURRENT_PORT_SIZE_PORT_SIZE_32_MASK -#define TPIU_CURRENT_PORT_SIZE_PORT_SIZE_32_DEFVAL 0x00000001 -#define TPIU_CURRENT_PORT_SIZE_PORT_SIZE_32_SHIFT 31 -#define TPIU_CURRENT_PORT_SIZE_PORT_SIZE_32_MASK 0x80000000U - -/*A write of 0xC5ACCE55 enables further write access to this device. A write of any value other than 0xC5ACCE55 will have the a - fect of removing write access.*/ -#undef TPIU_LAR_ACCESS_W_DEFVAL -#undef TPIU_LAR_ACCESS_W_SHIFT -#undef TPIU_LAR_ACCESS_W_MASK -#define TPIU_LAR_ACCESS_W_DEFVAL -#define TPIU_LAR_ACCESS_W_SHIFT 0 -#define TPIU_LAR_ACCESS_W_MASK 0xFFFFFFFFU - -/*Baud rate divider value: 0 - 3: ignored 4 - 255: Baud rate*/ -#undef UART0_BAUD_RATE_DIVIDER_REG0_BDIV_DEFVAL -#undef UART0_BAUD_RATE_DIVIDER_REG0_BDIV_SHIFT -#undef UART0_BAUD_RATE_DIVIDER_REG0_BDIV_MASK -#define UART0_BAUD_RATE_DIVIDER_REG0_BDIV_DEFVAL 0x0000000F -#define UART0_BAUD_RATE_DIVIDER_REG0_BDIV_SHIFT 0 -#define UART0_BAUD_RATE_DIVIDER_REG0_BDIV_MASK 0x000000FFU - -/*Baud Rate Clock Divisor Value: 0: Disables baud_sample 1: Clock divisor bypass (baud_sample = sel_clk) 2 - 65535: baud_sample*/ -#undef UART0_BAUD_RATE_GEN_REG0_CD_DEFVAL -#undef UART0_BAUD_RATE_GEN_REG0_CD_SHIFT -#undef UART0_BAUD_RATE_GEN_REG0_CD_MASK -#define UART0_BAUD_RATE_GEN_REG0_CD_DEFVAL 0x0000028B -#define UART0_BAUD_RATE_GEN_REG0_CD_SHIFT 0 -#define UART0_BAUD_RATE_GEN_REG0_CD_MASK 0x0000FFFFU - -/*Stop transmitter break: 0: no affect 1: stop transmission of the break after a minimum of one character length and transmit a - high level during 12 bit periods. It can be set regardless of the value of STTBRK.*/ -#undef UART0_CONTROL_REG0_STPBRK_DEFVAL -#undef UART0_CONTROL_REG0_STPBRK_SHIFT -#undef UART0_CONTROL_REG0_STPBRK_MASK -#define UART0_CONTROL_REG0_STPBRK_DEFVAL 0x00000128 -#define UART0_CONTROL_REG0_STPBRK_SHIFT 8 -#define UART0_CONTROL_REG0_STPBRK_MASK 0x00000100U - -/*Start transmitter break: 0: no affect 1: start to transmit a break after the characters currently present in the FIFO and the - transmit shift register have been transmitted. It can only be set if STPBRK (Stop transmitter break) is not high.*/ -#undef UART0_CONTROL_REG0_STTBRK_DEFVAL -#undef UART0_CONTROL_REG0_STTBRK_SHIFT -#undef UART0_CONTROL_REG0_STTBRK_MASK -#define UART0_CONTROL_REG0_STTBRK_DEFVAL 0x00000128 -#define UART0_CONTROL_REG0_STTBRK_SHIFT 7 -#define UART0_CONTROL_REG0_STTBRK_MASK 0x00000080U - -/*Restart receiver timeout counter: 1: receiver timeout counter is restarted. This bit is self clearing once the restart has co - pleted.*/ -#undef UART0_CONTROL_REG0_RSTTO_DEFVAL -#undef UART0_CONTROL_REG0_RSTTO_SHIFT -#undef UART0_CONTROL_REG0_RSTTO_MASK -#define UART0_CONTROL_REG0_RSTTO_DEFVAL 0x00000128 -#define UART0_CONTROL_REG0_RSTTO_SHIFT 6 -#define UART0_CONTROL_REG0_RSTTO_MASK 0x00000040U - -/*Transmit disable: 0: enable transmitter 1: disable transmitter*/ -#undef UART0_CONTROL_REG0_TXDIS_DEFVAL -#undef UART0_CONTROL_REG0_TXDIS_SHIFT -#undef UART0_CONTROL_REG0_TXDIS_MASK -#define UART0_CONTROL_REG0_TXDIS_DEFVAL 0x00000128 -#define UART0_CONTROL_REG0_TXDIS_SHIFT 5 -#define UART0_CONTROL_REG0_TXDIS_MASK 0x00000020U - -/*Transmit enable: 0: disable transmitter 1: enable transmitter, provided the TXDIS field is set to 0.*/ -#undef UART0_CONTROL_REG0_TXEN_DEFVAL -#undef UART0_CONTROL_REG0_TXEN_SHIFT -#undef UART0_CONTROL_REG0_TXEN_MASK -#define UART0_CONTROL_REG0_TXEN_DEFVAL 0x00000128 -#define UART0_CONTROL_REG0_TXEN_SHIFT 4 -#define UART0_CONTROL_REG0_TXEN_MASK 0x00000010U - -/*Receive disable: 0: enable 1: disable, regardless of the value of RXEN*/ -#undef UART0_CONTROL_REG0_RXDIS_DEFVAL -#undef UART0_CONTROL_REG0_RXDIS_SHIFT -#undef UART0_CONTROL_REG0_RXDIS_MASK -#define UART0_CONTROL_REG0_RXDIS_DEFVAL 0x00000128 -#define UART0_CONTROL_REG0_RXDIS_SHIFT 3 -#define UART0_CONTROL_REG0_RXDIS_MASK 0x00000008U - -/*Receive enable: 0: disable 1: enable When set to one, the receiver logic is enabled, provided the RXDIS field is set to zero.*/ -#undef UART0_CONTROL_REG0_RXEN_DEFVAL -#undef UART0_CONTROL_REG0_RXEN_SHIFT -#undef UART0_CONTROL_REG0_RXEN_MASK -#define UART0_CONTROL_REG0_RXEN_DEFVAL 0x00000128 -#define UART0_CONTROL_REG0_RXEN_SHIFT 2 -#define UART0_CONTROL_REG0_RXEN_MASK 0x00000004U - -/*Software reset for Tx data path: 0: no affect 1: transmitter logic is reset and all pending transmitter data is discarded Thi - bit is self clearing once the reset has completed.*/ -#undef UART0_CONTROL_REG0_TXRES_DEFVAL -#undef UART0_CONTROL_REG0_TXRES_SHIFT -#undef UART0_CONTROL_REG0_TXRES_MASK -#define UART0_CONTROL_REG0_TXRES_DEFVAL 0x00000128 -#define UART0_CONTROL_REG0_TXRES_SHIFT 1 -#define UART0_CONTROL_REG0_TXRES_MASK 0x00000002U - -/*Software reset for Rx data path: 0: no affect 1: receiver logic is reset and all pending receiver data is discarded. This bit - is self clearing once the reset has completed.*/ -#undef UART0_CONTROL_REG0_RXRES_DEFVAL -#undef UART0_CONTROL_REG0_RXRES_SHIFT -#undef UART0_CONTROL_REG0_RXRES_MASK -#define UART0_CONTROL_REG0_RXRES_DEFVAL 0x00000128 -#define UART0_CONTROL_REG0_RXRES_SHIFT 0 -#define UART0_CONTROL_REG0_RXRES_MASK 0x00000001U - -/*Channel mode: Defines the mode of operation of the UART. 00: normal 01: automatic echo 10: local loopback 11: remote loopback*/ -#undef UART0_MODE_REG0_CHMODE_DEFVAL -#undef UART0_MODE_REG0_CHMODE_SHIFT -#undef UART0_MODE_REG0_CHMODE_MASK -#define UART0_MODE_REG0_CHMODE_DEFVAL 0x00000000 -#define UART0_MODE_REG0_CHMODE_SHIFT 8 -#define UART0_MODE_REG0_CHMODE_MASK 0x00000300U - -/*Number of stop bits: Defines the number of stop bits to detect on receive and to generate on transmit. 00: 1 stop bit 01: 1.5 - stop bits 10: 2 stop bits 11: reserved*/ -#undef UART0_MODE_REG0_NBSTOP_DEFVAL -#undef UART0_MODE_REG0_NBSTOP_SHIFT -#undef UART0_MODE_REG0_NBSTOP_MASK -#define UART0_MODE_REG0_NBSTOP_DEFVAL 0x00000000 -#define UART0_MODE_REG0_NBSTOP_SHIFT 6 -#define UART0_MODE_REG0_NBSTOP_MASK 0x000000C0U - -/*Parity type select: Defines the expected parity to check on receive and the parity to generate on transmit. 000: even parity - 01: odd parity 010: forced to 0 parity (space) 011: forced to 1 parity (mark) 1xx: no parity*/ -#undef UART0_MODE_REG0_PAR_DEFVAL -#undef UART0_MODE_REG0_PAR_SHIFT -#undef UART0_MODE_REG0_PAR_MASK -#define UART0_MODE_REG0_PAR_DEFVAL 0x00000000 -#define UART0_MODE_REG0_PAR_SHIFT 3 -#define UART0_MODE_REG0_PAR_MASK 0x00000038U - -/*Character length select: Defines the number of bits in each character. 11: 6 bits 10: 7 bits 0x: 8 bits*/ -#undef UART0_MODE_REG0_CHRL_DEFVAL -#undef UART0_MODE_REG0_CHRL_SHIFT -#undef UART0_MODE_REG0_CHRL_MASK -#define UART0_MODE_REG0_CHRL_DEFVAL 0x00000000 -#define UART0_MODE_REG0_CHRL_SHIFT 1 -#define UART0_MODE_REG0_CHRL_MASK 0x00000006U - -/*Clock source select: This field defines whether a pre-scalar of 8 is applied to the baud rate generator input clock. 0: clock - source is uart_ref_clk 1: clock source is uart_ref_clk/8*/ -#undef UART0_MODE_REG0_CLKS_DEFVAL -#undef UART0_MODE_REG0_CLKS_SHIFT -#undef UART0_MODE_REG0_CLKS_MASK -#define UART0_MODE_REG0_CLKS_DEFVAL 0x00000000 -#define UART0_MODE_REG0_CLKS_SHIFT 0 -#define UART0_MODE_REG0_CLKS_MASK 0x00000001U - -/*Baud rate divider value: 0 - 3: ignored 4 - 255: Baud rate*/ -#undef UART1_BAUD_RATE_DIVIDER_REG0_BDIV_DEFVAL -#undef UART1_BAUD_RATE_DIVIDER_REG0_BDIV_SHIFT -#undef UART1_BAUD_RATE_DIVIDER_REG0_BDIV_MASK -#define UART1_BAUD_RATE_DIVIDER_REG0_BDIV_DEFVAL 0x0000000F -#define UART1_BAUD_RATE_DIVIDER_REG0_BDIV_SHIFT 0 -#define UART1_BAUD_RATE_DIVIDER_REG0_BDIV_MASK 0x000000FFU - -/*Baud Rate Clock Divisor Value: 0: Disables baud_sample 1: Clock divisor bypass (baud_sample = sel_clk) 2 - 65535: baud_sample*/ -#undef UART1_BAUD_RATE_GEN_REG0_CD_DEFVAL -#undef UART1_BAUD_RATE_GEN_REG0_CD_SHIFT -#undef UART1_BAUD_RATE_GEN_REG0_CD_MASK -#define UART1_BAUD_RATE_GEN_REG0_CD_DEFVAL 0x0000028B -#define UART1_BAUD_RATE_GEN_REG0_CD_SHIFT 0 -#define UART1_BAUD_RATE_GEN_REG0_CD_MASK 0x0000FFFFU - -/*Stop transmitter break: 0: no affect 1: stop transmission of the break after a minimum of one character length and transmit a - high level during 12 bit periods. It can be set regardless of the value of STTBRK.*/ -#undef UART1_CONTROL_REG0_STPBRK_DEFVAL -#undef UART1_CONTROL_REG0_STPBRK_SHIFT -#undef UART1_CONTROL_REG0_STPBRK_MASK -#define UART1_CONTROL_REG0_STPBRK_DEFVAL 0x00000128 -#define UART1_CONTROL_REG0_STPBRK_SHIFT 8 -#define UART1_CONTROL_REG0_STPBRK_MASK 0x00000100U - -/*Start transmitter break: 0: no affect 1: start to transmit a break after the characters currently present in the FIFO and the - transmit shift register have been transmitted. It can only be set if STPBRK (Stop transmitter break) is not high.*/ -#undef UART1_CONTROL_REG0_STTBRK_DEFVAL -#undef UART1_CONTROL_REG0_STTBRK_SHIFT -#undef UART1_CONTROL_REG0_STTBRK_MASK -#define UART1_CONTROL_REG0_STTBRK_DEFVAL 0x00000128 -#define UART1_CONTROL_REG0_STTBRK_SHIFT 7 -#define UART1_CONTROL_REG0_STTBRK_MASK 0x00000080U - -/*Restart receiver timeout counter: 1: receiver timeout counter is restarted. This bit is self clearing once the restart has co - pleted.*/ -#undef UART1_CONTROL_REG0_RSTTO_DEFVAL -#undef UART1_CONTROL_REG0_RSTTO_SHIFT -#undef UART1_CONTROL_REG0_RSTTO_MASK -#define UART1_CONTROL_REG0_RSTTO_DEFVAL 0x00000128 -#define UART1_CONTROL_REG0_RSTTO_SHIFT 6 -#define UART1_CONTROL_REG0_RSTTO_MASK 0x00000040U - -/*Transmit disable: 0: enable transmitter 1: disable transmitter*/ -#undef UART1_CONTROL_REG0_TXDIS_DEFVAL -#undef UART1_CONTROL_REG0_TXDIS_SHIFT -#undef UART1_CONTROL_REG0_TXDIS_MASK -#define UART1_CONTROL_REG0_TXDIS_DEFVAL 0x00000128 -#define UART1_CONTROL_REG0_TXDIS_SHIFT 5 -#define UART1_CONTROL_REG0_TXDIS_MASK 0x00000020U - -/*Transmit enable: 0: disable transmitter 1: enable transmitter, provided the TXDIS field is set to 0.*/ -#undef UART1_CONTROL_REG0_TXEN_DEFVAL -#undef UART1_CONTROL_REG0_TXEN_SHIFT -#undef UART1_CONTROL_REG0_TXEN_MASK -#define UART1_CONTROL_REG0_TXEN_DEFVAL 0x00000128 -#define UART1_CONTROL_REG0_TXEN_SHIFT 4 -#define UART1_CONTROL_REG0_TXEN_MASK 0x00000010U - -/*Receive disable: 0: enable 1: disable, regardless of the value of RXEN*/ -#undef UART1_CONTROL_REG0_RXDIS_DEFVAL -#undef UART1_CONTROL_REG0_RXDIS_SHIFT -#undef UART1_CONTROL_REG0_RXDIS_MASK -#define UART1_CONTROL_REG0_RXDIS_DEFVAL 0x00000128 -#define UART1_CONTROL_REG0_RXDIS_SHIFT 3 -#define UART1_CONTROL_REG0_RXDIS_MASK 0x00000008U - -/*Receive enable: 0: disable 1: enable When set to one, the receiver logic is enabled, provided the RXDIS field is set to zero.*/ -#undef UART1_CONTROL_REG0_RXEN_DEFVAL -#undef UART1_CONTROL_REG0_RXEN_SHIFT -#undef UART1_CONTROL_REG0_RXEN_MASK -#define UART1_CONTROL_REG0_RXEN_DEFVAL 0x00000128 -#define UART1_CONTROL_REG0_RXEN_SHIFT 2 -#define UART1_CONTROL_REG0_RXEN_MASK 0x00000004U - -/*Software reset for Tx data path: 0: no affect 1: transmitter logic is reset and all pending transmitter data is discarded Thi - bit is self clearing once the reset has completed.*/ -#undef UART1_CONTROL_REG0_TXRES_DEFVAL -#undef UART1_CONTROL_REG0_TXRES_SHIFT -#undef UART1_CONTROL_REG0_TXRES_MASK -#define UART1_CONTROL_REG0_TXRES_DEFVAL 0x00000128 -#define UART1_CONTROL_REG0_TXRES_SHIFT 1 -#define UART1_CONTROL_REG0_TXRES_MASK 0x00000002U - -/*Software reset for Rx data path: 0: no affect 1: receiver logic is reset and all pending receiver data is discarded. This bit - is self clearing once the reset has completed.*/ -#undef UART1_CONTROL_REG0_RXRES_DEFVAL -#undef UART1_CONTROL_REG0_RXRES_SHIFT -#undef UART1_CONTROL_REG0_RXRES_MASK -#define UART1_CONTROL_REG0_RXRES_DEFVAL 0x00000128 -#define UART1_CONTROL_REG0_RXRES_SHIFT 0 -#define UART1_CONTROL_REG0_RXRES_MASK 0x00000001U - -/*Channel mode: Defines the mode of operation of the UART. 00: normal 01: automatic echo 10: local loopback 11: remote loopback*/ -#undef UART1_MODE_REG0_CHMODE_DEFVAL -#undef UART1_MODE_REG0_CHMODE_SHIFT -#undef UART1_MODE_REG0_CHMODE_MASK -#define UART1_MODE_REG0_CHMODE_DEFVAL 0x00000000 -#define UART1_MODE_REG0_CHMODE_SHIFT 8 -#define UART1_MODE_REG0_CHMODE_MASK 0x00000300U - -/*Number of stop bits: Defines the number of stop bits to detect on receive and to generate on transmit. 00: 1 stop bit 01: 1.5 - stop bits 10: 2 stop bits 11: reserved*/ -#undef UART1_MODE_REG0_NBSTOP_DEFVAL -#undef UART1_MODE_REG0_NBSTOP_SHIFT -#undef UART1_MODE_REG0_NBSTOP_MASK -#define UART1_MODE_REG0_NBSTOP_DEFVAL 0x00000000 -#define UART1_MODE_REG0_NBSTOP_SHIFT 6 -#define UART1_MODE_REG0_NBSTOP_MASK 0x000000C0U - -/*Parity type select: Defines the expected parity to check on receive and the parity to generate on transmit. 000: even parity - 01: odd parity 010: forced to 0 parity (space) 011: forced to 1 parity (mark) 1xx: no parity*/ -#undef UART1_MODE_REG0_PAR_DEFVAL -#undef UART1_MODE_REG0_PAR_SHIFT -#undef UART1_MODE_REG0_PAR_MASK -#define UART1_MODE_REG0_PAR_DEFVAL 0x00000000 -#define UART1_MODE_REG0_PAR_SHIFT 3 -#define UART1_MODE_REG0_PAR_MASK 0x00000038U - -/*Character length select: Defines the number of bits in each character. 11: 6 bits 10: 7 bits 0x: 8 bits*/ -#undef UART1_MODE_REG0_CHRL_DEFVAL -#undef UART1_MODE_REG0_CHRL_SHIFT -#undef UART1_MODE_REG0_CHRL_MASK -#define UART1_MODE_REG0_CHRL_DEFVAL 0x00000000 -#define UART1_MODE_REG0_CHRL_SHIFT 1 -#define UART1_MODE_REG0_CHRL_MASK 0x00000006U - -/*Clock source select: This field defines whether a pre-scalar of 8 is applied to the baud rate generator input clock. 0: clock - source is uart_ref_clk 1: clock source is uart_ref_clk/8*/ -#undef UART1_MODE_REG0_CLKS_DEFVAL -#undef UART1_MODE_REG0_CLKS_SHIFT -#undef UART1_MODE_REG0_CLKS_MASK -#define UART1_MODE_REG0_CLKS_DEFVAL 0x00000000 -#define UART1_MODE_REG0_CLKS_SHIFT 0 -#define UART1_MODE_REG0_CLKS_MASK 0x00000001U - -/*TrustZone Classification for ADMA*/ -#undef LPD_SLCR_SECURE_SLCR_ADMA_TZ_DEFVAL -#undef LPD_SLCR_SECURE_SLCR_ADMA_TZ_SHIFT -#undef LPD_SLCR_SECURE_SLCR_ADMA_TZ_MASK -#define LPD_SLCR_SECURE_SLCR_ADMA_TZ_DEFVAL -#define LPD_SLCR_SECURE_SLCR_ADMA_TZ_SHIFT 0 -#define LPD_SLCR_SECURE_SLCR_ADMA_TZ_MASK 0x000000FFU - -/*CSU regsiter*/ -#undef CSU_TAMPER_STATUS_TAMPER_0_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_0_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_0_MASK -#define CSU_TAMPER_STATUS_TAMPER_0_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_0_SHIFT 0 -#define CSU_TAMPER_STATUS_TAMPER_0_MASK 0x00000001U - -/*External MIO*/ -#undef CSU_TAMPER_STATUS_TAMPER_1_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_1_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_1_MASK -#define CSU_TAMPER_STATUS_TAMPER_1_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_1_SHIFT 1 -#define CSU_TAMPER_STATUS_TAMPER_1_MASK 0x00000002U - -/*JTAG toggle detect*/ -#undef CSU_TAMPER_STATUS_TAMPER_2_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_2_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_2_MASK -#define CSU_TAMPER_STATUS_TAMPER_2_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_2_SHIFT 2 -#define CSU_TAMPER_STATUS_TAMPER_2_MASK 0x00000004U - -/*PL SEU error*/ -#undef CSU_TAMPER_STATUS_TAMPER_3_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_3_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_3_MASK -#define CSU_TAMPER_STATUS_TAMPER_3_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_3_SHIFT 3 -#define CSU_TAMPER_STATUS_TAMPER_3_MASK 0x00000008U - -/*AMS over temperature alarm for LPD*/ -#undef CSU_TAMPER_STATUS_TAMPER_4_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_4_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_4_MASK -#define CSU_TAMPER_STATUS_TAMPER_4_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_4_SHIFT 4 -#define CSU_TAMPER_STATUS_TAMPER_4_MASK 0x00000010U - -/*AMS over temperature alarm for APU*/ -#undef CSU_TAMPER_STATUS_TAMPER_5_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_5_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_5_MASK -#define CSU_TAMPER_STATUS_TAMPER_5_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_5_SHIFT 5 -#define CSU_TAMPER_STATUS_TAMPER_5_MASK 0x00000020U - -/*AMS voltage alarm for VCCPINT_FPD*/ -#undef CSU_TAMPER_STATUS_TAMPER_6_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_6_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_6_MASK -#define CSU_TAMPER_STATUS_TAMPER_6_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_6_SHIFT 6 -#define CSU_TAMPER_STATUS_TAMPER_6_MASK 0x00000040U - -/*AMS voltage alarm for VCCPINT_LPD*/ -#undef CSU_TAMPER_STATUS_TAMPER_7_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_7_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_7_MASK -#define CSU_TAMPER_STATUS_TAMPER_7_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_7_SHIFT 7 -#define CSU_TAMPER_STATUS_TAMPER_7_MASK 0x00000080U - -/*AMS voltage alarm for VCCPAUX*/ -#undef CSU_TAMPER_STATUS_TAMPER_8_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_8_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_8_MASK -#define CSU_TAMPER_STATUS_TAMPER_8_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_8_SHIFT 8 -#define CSU_TAMPER_STATUS_TAMPER_8_MASK 0x00000100U - -/*AMS voltage alarm for DDRPHY*/ -#undef CSU_TAMPER_STATUS_TAMPER_9_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_9_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_9_MASK -#define CSU_TAMPER_STATUS_TAMPER_9_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_9_SHIFT 9 -#define CSU_TAMPER_STATUS_TAMPER_9_MASK 0x00000200U - -/*AMS voltage alarm for PSIO bank 0/1/2*/ -#undef CSU_TAMPER_STATUS_TAMPER_10_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_10_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_10_MASK -#define CSU_TAMPER_STATUS_TAMPER_10_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_10_SHIFT 10 -#define CSU_TAMPER_STATUS_TAMPER_10_MASK 0x00000400U - -/*AMS voltage alarm for PSIO bank 3 (dedicated pins)*/ -#undef CSU_TAMPER_STATUS_TAMPER_11_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_11_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_11_MASK -#define CSU_TAMPER_STATUS_TAMPER_11_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_11_SHIFT 11 -#define CSU_TAMPER_STATUS_TAMPER_11_MASK 0x00000800U - -/*AMS voltaage alarm for GT*/ -#undef CSU_TAMPER_STATUS_TAMPER_12_DEFVAL -#undef CSU_TAMPER_STATUS_TAMPER_12_SHIFT -#undef CSU_TAMPER_STATUS_TAMPER_12_MASK -#define CSU_TAMPER_STATUS_TAMPER_12_DEFVAL 0x00000000 -#define CSU_TAMPER_STATUS_TAMPER_12_SHIFT 12 -#define CSU_TAMPER_STATUS_TAMPER_12_MASK 0x00001000U - -/*Set ACE outgoing AWQOS value*/ -#undef APU_ACE_CTRL_AWQOS_DEFVAL -#undef APU_ACE_CTRL_AWQOS_SHIFT -#undef APU_ACE_CTRL_AWQOS_MASK -#define APU_ACE_CTRL_AWQOS_DEFVAL 0x000F000F -#define APU_ACE_CTRL_AWQOS_SHIFT 16 -#define APU_ACE_CTRL_AWQOS_MASK 0x000F0000U - -/*Set ACE outgoing ARQOS value*/ -#undef APU_ACE_CTRL_ARQOS_DEFVAL -#undef APU_ACE_CTRL_ARQOS_SHIFT -#undef APU_ACE_CTRL_ARQOS_MASK -#define APU_ACE_CTRL_ARQOS_DEFVAL 0x000F000F -#define APU_ACE_CTRL_ARQOS_SHIFT 0 -#define APU_ACE_CTRL_ARQOS_MASK 0x0000000FU - -/*Enables the RTC. By writing a 0 to this bit, RTC will be powered off and the only module that potentially draws current from - he battery will be BBRAM. The value read through this bit does not necessarily reflect whether RTC is enabled or not. It is e - pected that RTC is enabled every time it is being configured. If RTC is not used in the design, FSBL will disable it by writi - g a 0 to this bit.*/ -#undef RTC_CONTROL_BATTERY_DISABLE_DEFVAL -#undef RTC_CONTROL_BATTERY_DISABLE_SHIFT -#undef RTC_CONTROL_BATTERY_DISABLE_MASK -#define RTC_CONTROL_BATTERY_DISABLE_DEFVAL 0x01000000 -#define RTC_CONTROL_BATTERY_DISABLE_SHIFT 31 -#define RTC_CONTROL_BATTERY_DISABLE_MASK 0x80000000U - -/*Frequency in number of ticks per second. Valid range from 10 MHz to 100 MHz.*/ -#undef IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_FREQ_DEFVAL -#undef IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_FREQ_SHIFT -#undef IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_FREQ_MASK -#define IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_FREQ_DEFVAL -#define IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_FREQ_SHIFT 0 -#define IOU_SCNTRS_BASE_FREQUENCY_ID_REGISTER_FREQ_MASK 0xFFFFFFFFU - -/*Enable 0: The counter is disabled and not incrementing. 1: The counter is enabled and is incrementing.*/ -#undef IOU_SCNTRS_COUNTER_CONTROL_REGISTER_EN_DEFVAL -#undef IOU_SCNTRS_COUNTER_CONTROL_REGISTER_EN_SHIFT -#undef IOU_SCNTRS_COUNTER_CONTROL_REGISTER_EN_MASK -#define IOU_SCNTRS_COUNTER_CONTROL_REGISTER_EN_DEFVAL 0x00000000 -#define IOU_SCNTRS_COUNTER_CONTROL_REGISTER_EN_SHIFT 0 -#define IOU_SCNTRS_COUNTER_CONTROL_REGISTER_EN_MASK 0x00000001U -#undef LPD_XPPU_CFG_MASTER_ID00_OFFSET -#define LPD_XPPU_CFG_MASTER_ID00_OFFSET 0XFF980100 -#undef LPD_XPPU_CFG_MASTER_ID01_OFFSET -#define LPD_XPPU_CFG_MASTER_ID01_OFFSET 0XFF980104 -#undef LPD_XPPU_CFG_MASTER_ID02_OFFSET -#define LPD_XPPU_CFG_MASTER_ID02_OFFSET 0XFF980108 -#undef LPD_XPPU_CFG_MASTER_ID03_OFFSET -#define LPD_XPPU_CFG_MASTER_ID03_OFFSET 0XFF98010C -#undef LPD_XPPU_CFG_MASTER_ID04_OFFSET -#define LPD_XPPU_CFG_MASTER_ID04_OFFSET 0XFF980110 -#undef LPD_XPPU_CFG_MASTER_ID05_OFFSET -#define LPD_XPPU_CFG_MASTER_ID05_OFFSET 0XFF980114 -#undef LPD_XPPU_CFG_MASTER_ID06_OFFSET -#define LPD_XPPU_CFG_MASTER_ID06_OFFSET 0XFF980118 -#undef LPD_XPPU_CFG_MASTER_ID07_OFFSET -#define LPD_XPPU_CFG_MASTER_ID07_OFFSET 0XFF98011C -#undef LPD_XPPU_CFG_MASTER_ID19_OFFSET -#define LPD_XPPU_CFG_MASTER_ID19_OFFSET 0XFF98014C -#undef LPD_XPPU_CFG_APERPERM_048_OFFSET -#define LPD_XPPU_CFG_APERPERM_048_OFFSET 0XFF9810C0 -#undef LPD_XPPU_CFG_APERPERM_049_OFFSET -#define LPD_XPPU_CFG_APERPERM_049_OFFSET 0XFF9810C4 -#undef LPD_XPPU_CFG_APERPERM_050_OFFSET -#define LPD_XPPU_CFG_APERPERM_050_OFFSET 0XFF9810C8 -#undef LPD_XPPU_CFG_APERPERM_051_OFFSET -#define LPD_XPPU_CFG_APERPERM_051_OFFSET 0XFF9810CC -#undef LPD_XPPU_CFG_APERPERM_256_OFFSET -#define LPD_XPPU_CFG_APERPERM_256_OFFSET 0XFF981400 -#undef LPD_XPPU_CFG_APERPERM_257_OFFSET -#define LPD_XPPU_CFG_APERPERM_257_OFFSET 0XFF981404 -#undef LPD_XPPU_CFG_APERPERM_258_OFFSET -#define LPD_XPPU_CFG_APERPERM_258_OFFSET 0XFF981408 -#undef LPD_XPPU_CFG_APERPERM_259_OFFSET -#define LPD_XPPU_CFG_APERPERM_259_OFFSET 0XFF98140C -#undef LPD_XPPU_CFG_APERPERM_260_OFFSET -#define LPD_XPPU_CFG_APERPERM_260_OFFSET 0XFF981410 -#undef LPD_XPPU_CFG_APERPERM_261_OFFSET -#define LPD_XPPU_CFG_APERPERM_261_OFFSET 0XFF981414 -#undef LPD_XPPU_CFG_APERPERM_262_OFFSET -#define LPD_XPPU_CFG_APERPERM_262_OFFSET 0XFF981418 -#undef LPD_XPPU_CFG_APERPERM_263_OFFSET -#define LPD_XPPU_CFG_APERPERM_263_OFFSET 0XFF98141C -#undef LPD_XPPU_CFG_APERPERM_264_OFFSET -#define LPD_XPPU_CFG_APERPERM_264_OFFSET 0XFF981420 -#undef LPD_XPPU_CFG_APERPERM_265_OFFSET -#define LPD_XPPU_CFG_APERPERM_265_OFFSET 0XFF981424 -#undef LPD_XPPU_CFG_APERPERM_266_OFFSET -#define LPD_XPPU_CFG_APERPERM_266_OFFSET 0XFF981428 -#undef LPD_XPPU_CFG_APERPERM_267_OFFSET -#define LPD_XPPU_CFG_APERPERM_267_OFFSET 0XFF98142C -#undef LPD_XPPU_CFG_APERPERM_268_OFFSET -#define LPD_XPPU_CFG_APERPERM_268_OFFSET 0XFF981430 -#undef LPD_XPPU_CFG_APERPERM_269_OFFSET -#define LPD_XPPU_CFG_APERPERM_269_OFFSET 0XFF981434 -#undef LPD_XPPU_CFG_APERPERM_270_OFFSET -#define LPD_XPPU_CFG_APERPERM_270_OFFSET 0XFF981438 -#undef LPD_XPPU_CFG_APERPERM_271_OFFSET -#define LPD_XPPU_CFG_APERPERM_271_OFFSET 0XFF98143C -#undef LPD_XPPU_CFG_APERPERM_272_OFFSET -#define LPD_XPPU_CFG_APERPERM_272_OFFSET 0XFF981440 -#undef LPD_XPPU_CFG_APERPERM_273_OFFSET -#define LPD_XPPU_CFG_APERPERM_273_OFFSET 0XFF981444 -#undef LPD_XPPU_CFG_APERPERM_274_OFFSET -#define LPD_XPPU_CFG_APERPERM_274_OFFSET 0XFF981448 -#undef LPD_XPPU_CFG_APERPERM_275_OFFSET -#define LPD_XPPU_CFG_APERPERM_275_OFFSET 0XFF98144C -#undef LPD_XPPU_CFG_APERPERM_276_OFFSET -#define LPD_XPPU_CFG_APERPERM_276_OFFSET 0XFF981450 -#undef LPD_XPPU_CFG_APERPERM_277_OFFSET -#define LPD_XPPU_CFG_APERPERM_277_OFFSET 0XFF981454 -#undef LPD_XPPU_CFG_APERPERM_278_OFFSET -#define LPD_XPPU_CFG_APERPERM_278_OFFSET 0XFF981458 -#undef LPD_XPPU_CFG_APERPERM_279_OFFSET -#define LPD_XPPU_CFG_APERPERM_279_OFFSET 0XFF98145C -#undef LPD_XPPU_CFG_APERPERM_280_OFFSET -#define LPD_XPPU_CFG_APERPERM_280_OFFSET 0XFF981460 -#undef LPD_XPPU_CFG_APERPERM_281_OFFSET -#define LPD_XPPU_CFG_APERPERM_281_OFFSET 0XFF981464 -#undef LPD_XPPU_CFG_APERPERM_282_OFFSET -#define LPD_XPPU_CFG_APERPERM_282_OFFSET 0XFF981468 -#undef LPD_XPPU_CFG_APERPERM_283_OFFSET -#define LPD_XPPU_CFG_APERPERM_283_OFFSET 0XFF98146C -#undef LPD_XPPU_CFG_APERPERM_284_OFFSET -#define LPD_XPPU_CFG_APERPERM_284_OFFSET 0XFF981470 -#undef LPD_XPPU_CFG_APERPERM_285_OFFSET -#define LPD_XPPU_CFG_APERPERM_285_OFFSET 0XFF981474 -#undef LPD_XPPU_CFG_APERPERM_286_OFFSET -#define LPD_XPPU_CFG_APERPERM_286_OFFSET 0XFF981478 -#undef LPD_XPPU_CFG_APERPERM_287_OFFSET -#define LPD_XPPU_CFG_APERPERM_287_OFFSET 0XFF98147C -#undef LPD_XPPU_CFG_APERPERM_288_OFFSET -#define LPD_XPPU_CFG_APERPERM_288_OFFSET 0XFF981480 -#undef LPD_XPPU_CFG_APERPERM_289_OFFSET -#define LPD_XPPU_CFG_APERPERM_289_OFFSET 0XFF981484 -#undef LPD_XPPU_CFG_APERPERM_290_OFFSET -#define LPD_XPPU_CFG_APERPERM_290_OFFSET 0XFF981488 -#undef LPD_XPPU_CFG_APERPERM_291_OFFSET -#define LPD_XPPU_CFG_APERPERM_291_OFFSET 0XFF98148C -#undef LPD_XPPU_CFG_APERPERM_292_OFFSET -#define LPD_XPPU_CFG_APERPERM_292_OFFSET 0XFF981490 -#undef LPD_XPPU_CFG_APERPERM_293_OFFSET -#define LPD_XPPU_CFG_APERPERM_293_OFFSET 0XFF981494 -#undef LPD_XPPU_CFG_APERPERM_294_OFFSET -#define LPD_XPPU_CFG_APERPERM_294_OFFSET 0XFF981498 -#undef LPD_XPPU_CFG_APERPERM_295_OFFSET -#define LPD_XPPU_CFG_APERPERM_295_OFFSET 0XFF98149C -#undef LPD_XPPU_CFG_APERPERM_296_OFFSET -#define LPD_XPPU_CFG_APERPERM_296_OFFSET 0XFF9814A0 -#undef LPD_XPPU_CFG_APERPERM_297_OFFSET -#define LPD_XPPU_CFG_APERPERM_297_OFFSET 0XFF9814A4 -#undef LPD_XPPU_CFG_APERPERM_298_OFFSET -#define LPD_XPPU_CFG_APERPERM_298_OFFSET 0XFF9814A8 -#undef LPD_XPPU_CFG_APERPERM_299_OFFSET -#define LPD_XPPU_CFG_APERPERM_299_OFFSET 0XFF9814AC -#undef LPD_XPPU_CFG_APERPERM_300_OFFSET -#define LPD_XPPU_CFG_APERPERM_300_OFFSET 0XFF9814B0 -#undef LPD_XPPU_CFG_APERPERM_301_OFFSET -#define LPD_XPPU_CFG_APERPERM_301_OFFSET 0XFF9814B4 -#undef LPD_XPPU_CFG_APERPERM_302_OFFSET -#define LPD_XPPU_CFG_APERPERM_302_OFFSET 0XFF9814B8 -#undef LPD_XPPU_CFG_APERPERM_303_OFFSET -#define LPD_XPPU_CFG_APERPERM_303_OFFSET 0XFF9814BC -#undef LPD_XPPU_CFG_APERPERM_304_OFFSET -#define LPD_XPPU_CFG_APERPERM_304_OFFSET 0XFF9814C0 -#undef LPD_XPPU_CFG_APERPERM_305_OFFSET -#define LPD_XPPU_CFG_APERPERM_305_OFFSET 0XFF9814C4 -#undef LPD_XPPU_CFG_APERPERM_306_OFFSET -#define LPD_XPPU_CFG_APERPERM_306_OFFSET 0XFF9814C8 -#undef LPD_XPPU_CFG_APERPERM_307_OFFSET -#define LPD_XPPU_CFG_APERPERM_307_OFFSET 0XFF9814CC -#undef LPD_XPPU_CFG_APERPERM_308_OFFSET -#define LPD_XPPU_CFG_APERPERM_308_OFFSET 0XFF9814D0 -#undef LPD_XPPU_CFG_APERPERM_309_OFFSET -#define LPD_XPPU_CFG_APERPERM_309_OFFSET 0XFF9814D4 -#undef LPD_XPPU_CFG_APERPERM_318_OFFSET -#define LPD_XPPU_CFG_APERPERM_318_OFFSET 0XFF9814F8 -#undef LPD_XPPU_CFG_APERPERM_319_OFFSET -#define LPD_XPPU_CFG_APERPERM_319_OFFSET 0XFF9814FC -#undef LPD_XPPU_CFG_APERPERM_320_OFFSET -#define LPD_XPPU_CFG_APERPERM_320_OFFSET 0XFF981500 -#undef LPD_XPPU_CFG_APERPERM_321_OFFSET -#define LPD_XPPU_CFG_APERPERM_321_OFFSET 0XFF981504 -#undef LPD_XPPU_CFG_APERPERM_322_OFFSET -#define LPD_XPPU_CFG_APERPERM_322_OFFSET 0XFF981508 -#undef LPD_XPPU_CFG_APERPERM_323_OFFSET -#define LPD_XPPU_CFG_APERPERM_323_OFFSET 0XFF98150C -#undef LPD_XPPU_CFG_APERPERM_324_OFFSET -#define LPD_XPPU_CFG_APERPERM_324_OFFSET 0XFF981510 -#undef LPD_XPPU_CFG_APERPERM_325_OFFSET -#define LPD_XPPU_CFG_APERPERM_325_OFFSET 0XFF981514 -#undef LPD_XPPU_CFG_APERPERM_334_OFFSET -#define LPD_XPPU_CFG_APERPERM_334_OFFSET 0XFF981538 -#undef LPD_XPPU_CFG_APERPERM_335_OFFSET -#define LPD_XPPU_CFG_APERPERM_335_OFFSET 0XFF98153C -#undef LPD_XPPU_CFG_APERPERM_336_OFFSET -#define LPD_XPPU_CFG_APERPERM_336_OFFSET 0XFF981540 -#undef LPD_XPPU_CFG_APERPERM_337_OFFSET -#define LPD_XPPU_CFG_APERPERM_337_OFFSET 0XFF981544 -#undef LPD_XPPU_CFG_APERPERM_338_OFFSET -#define LPD_XPPU_CFG_APERPERM_338_OFFSET 0XFF981548 -#undef LPD_XPPU_CFG_APERPERM_339_OFFSET -#define LPD_XPPU_CFG_APERPERM_339_OFFSET 0XFF98154C -#undef LPD_XPPU_CFG_APERPERM_340_OFFSET -#define LPD_XPPU_CFG_APERPERM_340_OFFSET 0XFF981550 -#undef LPD_XPPU_CFG_APERPERM_341_OFFSET -#define LPD_XPPU_CFG_APERPERM_341_OFFSET 0XFF981554 -#undef LPD_XPPU_CFG_APERPERM_350_OFFSET -#define LPD_XPPU_CFG_APERPERM_350_OFFSET 0XFF981578 -#undef LPD_XPPU_CFG_APERPERM_351_OFFSET -#define LPD_XPPU_CFG_APERPERM_351_OFFSET 0XFF98157C -#undef LPD_XPPU_CFG_APERPERM_352_OFFSET -#define LPD_XPPU_CFG_APERPERM_352_OFFSET 0XFF981580 -#undef LPD_XPPU_CFG_APERPERM_353_OFFSET -#define LPD_XPPU_CFG_APERPERM_353_OFFSET 0XFF981584 -#undef LPD_XPPU_CFG_APERPERM_354_OFFSET -#define LPD_XPPU_CFG_APERPERM_354_OFFSET 0XFF981588 -#undef LPD_XPPU_CFG_APERPERM_355_OFFSET -#define LPD_XPPU_CFG_APERPERM_355_OFFSET 0XFF98158C -#undef LPD_XPPU_CFG_APERPERM_356_OFFSET -#define LPD_XPPU_CFG_APERPERM_356_OFFSET 0XFF981590 -#undef LPD_XPPU_CFG_APERPERM_357_OFFSET -#define LPD_XPPU_CFG_APERPERM_357_OFFSET 0XFF981594 -#undef LPD_XPPU_CFG_APERPERM_366_OFFSET -#define LPD_XPPU_CFG_APERPERM_366_OFFSET 0XFF9815B8 -#undef LPD_XPPU_CFG_APERPERM_367_OFFSET -#define LPD_XPPU_CFG_APERPERM_367_OFFSET 0XFF9815BC -#undef LPD_XPPU_CFG_APERPERM_368_OFFSET -#define LPD_XPPU_CFG_APERPERM_368_OFFSET 0XFF9815C0 -#undef LPD_XPPU_CFG_APERPERM_369_OFFSET -#define LPD_XPPU_CFG_APERPERM_369_OFFSET 0XFF9815C4 -#undef LPD_XPPU_CFG_APERPERM_370_OFFSET -#define LPD_XPPU_CFG_APERPERM_370_OFFSET 0XFF9815C8 -#undef LPD_XPPU_CFG_APERPERM_371_OFFSET -#define LPD_XPPU_CFG_APERPERM_371_OFFSET 0XFF9815CC -#undef LPD_XPPU_CFG_APERPERM_372_OFFSET -#define LPD_XPPU_CFG_APERPERM_372_OFFSET 0XFF9815D0 -#undef LPD_XPPU_CFG_APERPERM_373_OFFSET -#define LPD_XPPU_CFG_APERPERM_373_OFFSET 0XFF9815D4 -#undef LPD_XPPU_CFG_APERPERM_374_OFFSET -#define LPD_XPPU_CFG_APERPERM_374_OFFSET 0XFF9815D8 -#undef LPD_XPPU_CFG_APERPERM_375_OFFSET -#define LPD_XPPU_CFG_APERPERM_375_OFFSET 0XFF9815DC -#undef LPD_XPPU_CFG_APERPERM_376_OFFSET -#define LPD_XPPU_CFG_APERPERM_376_OFFSET 0XFF9815E0 -#undef LPD_XPPU_CFG_APERPERM_377_OFFSET -#define LPD_XPPU_CFG_APERPERM_377_OFFSET 0XFF9815E4 -#undef LPD_XPPU_CFG_APERPERM_378_OFFSET -#define LPD_XPPU_CFG_APERPERM_378_OFFSET 0XFF9815E8 -#undef LPD_XPPU_CFG_APERPERM_379_OFFSET -#define LPD_XPPU_CFG_APERPERM_379_OFFSET 0XFF9815EC -#undef LPD_XPPU_CFG_APERPERM_380_OFFSET -#define LPD_XPPU_CFG_APERPERM_380_OFFSET 0XFF9815F0 -#undef LPD_XPPU_CFG_APERPERM_381_OFFSET -#define LPD_XPPU_CFG_APERPERM_381_OFFSET 0XFF9815F4 -#undef LPD_XPPU_CFG_APERPERM_382_OFFSET -#define LPD_XPPU_CFG_APERPERM_382_OFFSET 0XFF9815F8 -#undef LPD_XPPU_CFG_APERPERM_383_OFFSET -#define LPD_XPPU_CFG_APERPERM_383_OFFSET 0XFF9815FC -#undef LPD_XPPU_SINK_ERR_CTRL_OFFSET -#define LPD_XPPU_SINK_ERR_CTRL_OFFSET 0XFF9CFFEC -#undef LPD_XPPU_CFG_CTRL_OFFSET -#define LPD_XPPU_CFG_CTRL_OFFSET 0XFF980000 -#undef LPD_XPPU_CFG_IEN_OFFSET -#define LPD_XPPU_CFG_IEN_OFFSET 0XFF980018 - -/*If set, only read transactions are allowed for the masters matching this register*/ -#undef LPD_XPPU_CFG_MASTER_ID00_MIDR_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID00_MIDR_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID00_MIDR_MASK -#define LPD_XPPU_CFG_MASTER_ID00_MIDR_DEFVAL 0x83FF0040 -#define LPD_XPPU_CFG_MASTER_ID00_MIDR_SHIFT 30 -#define LPD_XPPU_CFG_MASTER_ID00_MIDR_MASK 0x40000000U - -/*Mask to be applied before comparing*/ -#undef LPD_XPPU_CFG_MASTER_ID00_MIDM_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID00_MIDM_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID00_MIDM_MASK -#define LPD_XPPU_CFG_MASTER_ID00_MIDM_DEFVAL 0x83FF0040 -#define LPD_XPPU_CFG_MASTER_ID00_MIDM_SHIFT 16 -#define LPD_XPPU_CFG_MASTER_ID00_MIDM_MASK 0x03FF0000U - -/*Predefined Master ID for PMU*/ -#undef LPD_XPPU_CFG_MASTER_ID00_MID_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID00_MID_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID00_MID_MASK -#define LPD_XPPU_CFG_MASTER_ID00_MID_DEFVAL 0x83FF0040 -#define LPD_XPPU_CFG_MASTER_ID00_MID_SHIFT 0 -#define LPD_XPPU_CFG_MASTER_ID00_MID_MASK 0x000003FFU - -/*If set, only read transactions are allowed for the masters matching this register*/ -#undef LPD_XPPU_CFG_MASTER_ID01_MIDR_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID01_MIDR_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID01_MIDR_MASK -#define LPD_XPPU_CFG_MASTER_ID01_MIDR_DEFVAL 0x03F00000 -#define LPD_XPPU_CFG_MASTER_ID01_MIDR_SHIFT 30 -#define LPD_XPPU_CFG_MASTER_ID01_MIDR_MASK 0x40000000U - -/*Mask to be applied before comparing*/ -#undef LPD_XPPU_CFG_MASTER_ID01_MIDM_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID01_MIDM_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID01_MIDM_MASK -#define LPD_XPPU_CFG_MASTER_ID01_MIDM_DEFVAL 0x03F00000 -#define LPD_XPPU_CFG_MASTER_ID01_MIDM_SHIFT 16 -#define LPD_XPPU_CFG_MASTER_ID01_MIDM_MASK 0x03FF0000U - -/*Predefined Master ID for RPU0*/ -#undef LPD_XPPU_CFG_MASTER_ID01_MID_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID01_MID_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID01_MID_MASK -#define LPD_XPPU_CFG_MASTER_ID01_MID_DEFVAL 0x03F00000 -#define LPD_XPPU_CFG_MASTER_ID01_MID_SHIFT 0 -#define LPD_XPPU_CFG_MASTER_ID01_MID_MASK 0x000003FFU - -/*If set, only read transactions are allowed for the masters matching this register*/ -#undef LPD_XPPU_CFG_MASTER_ID02_MIDR_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID02_MIDR_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID02_MIDR_MASK -#define LPD_XPPU_CFG_MASTER_ID02_MIDR_DEFVAL 0x83F00010 -#define LPD_XPPU_CFG_MASTER_ID02_MIDR_SHIFT 30 -#define LPD_XPPU_CFG_MASTER_ID02_MIDR_MASK 0x40000000U - -/*Mask to be applied before comparing*/ -#undef LPD_XPPU_CFG_MASTER_ID02_MIDM_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID02_MIDM_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID02_MIDM_MASK -#define LPD_XPPU_CFG_MASTER_ID02_MIDM_DEFVAL 0x83F00010 -#define LPD_XPPU_CFG_MASTER_ID02_MIDM_SHIFT 16 -#define LPD_XPPU_CFG_MASTER_ID02_MIDM_MASK 0x03FF0000U - -/*Predefined Master ID for RPU1*/ -#undef LPD_XPPU_CFG_MASTER_ID02_MID_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID02_MID_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID02_MID_MASK -#define LPD_XPPU_CFG_MASTER_ID02_MID_DEFVAL 0x83F00010 -#define LPD_XPPU_CFG_MASTER_ID02_MID_SHIFT 0 -#define LPD_XPPU_CFG_MASTER_ID02_MID_MASK 0x000003FFU - -/*If set, only read transactions are allowed for the masters matching this register*/ -#undef LPD_XPPU_CFG_MASTER_ID03_MIDR_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID03_MIDR_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID03_MIDR_MASK -#define LPD_XPPU_CFG_MASTER_ID03_MIDR_DEFVAL 0x83C00080 -#define LPD_XPPU_CFG_MASTER_ID03_MIDR_SHIFT 30 -#define LPD_XPPU_CFG_MASTER_ID03_MIDR_MASK 0x40000000U - -/*Mask to be applied before comparing*/ -#undef LPD_XPPU_CFG_MASTER_ID03_MIDM_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID03_MIDM_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID03_MIDM_MASK -#define LPD_XPPU_CFG_MASTER_ID03_MIDM_DEFVAL 0x83C00080 -#define LPD_XPPU_CFG_MASTER_ID03_MIDM_SHIFT 16 -#define LPD_XPPU_CFG_MASTER_ID03_MIDM_MASK 0x03FF0000U - -/*Predefined Master ID for APU*/ -#undef LPD_XPPU_CFG_MASTER_ID03_MID_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID03_MID_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID03_MID_MASK -#define LPD_XPPU_CFG_MASTER_ID03_MID_DEFVAL 0x83C00080 -#define LPD_XPPU_CFG_MASTER_ID03_MID_SHIFT 0 -#define LPD_XPPU_CFG_MASTER_ID03_MID_MASK 0x000003FFU - -/*If set, only read transactions are allowed for the masters matching this register*/ -#undef LPD_XPPU_CFG_MASTER_ID04_MIDR_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID04_MIDR_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID04_MIDR_MASK -#define LPD_XPPU_CFG_MASTER_ID04_MIDR_DEFVAL 0x83C30080 -#define LPD_XPPU_CFG_MASTER_ID04_MIDR_SHIFT 30 -#define LPD_XPPU_CFG_MASTER_ID04_MIDR_MASK 0x40000000U - -/*Mask to be applied before comparing*/ -#undef LPD_XPPU_CFG_MASTER_ID04_MIDM_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID04_MIDM_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID04_MIDM_MASK -#define LPD_XPPU_CFG_MASTER_ID04_MIDM_DEFVAL 0x83C30080 -#define LPD_XPPU_CFG_MASTER_ID04_MIDM_SHIFT 16 -#define LPD_XPPU_CFG_MASTER_ID04_MIDM_MASK 0x03FF0000U - -/*Predefined Master ID for A53 Core 0*/ -#undef LPD_XPPU_CFG_MASTER_ID04_MID_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID04_MID_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID04_MID_MASK -#define LPD_XPPU_CFG_MASTER_ID04_MID_DEFVAL 0x83C30080 -#define LPD_XPPU_CFG_MASTER_ID04_MID_SHIFT 0 -#define LPD_XPPU_CFG_MASTER_ID04_MID_MASK 0x000003FFU - -/*If set, only read transactions are allowed for the masters matching this register*/ -#undef LPD_XPPU_CFG_MASTER_ID05_MIDR_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID05_MIDR_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID05_MIDR_MASK -#define LPD_XPPU_CFG_MASTER_ID05_MIDR_DEFVAL 0x03C30081 -#define LPD_XPPU_CFG_MASTER_ID05_MIDR_SHIFT 30 -#define LPD_XPPU_CFG_MASTER_ID05_MIDR_MASK 0x40000000U - -/*Mask to be applied before comparing*/ -#undef LPD_XPPU_CFG_MASTER_ID05_MIDM_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID05_MIDM_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID05_MIDM_MASK -#define LPD_XPPU_CFG_MASTER_ID05_MIDM_DEFVAL 0x03C30081 -#define LPD_XPPU_CFG_MASTER_ID05_MIDM_SHIFT 16 -#define LPD_XPPU_CFG_MASTER_ID05_MIDM_MASK 0x03FF0000U - -/*Predefined Master ID for A53 Core 1*/ -#undef LPD_XPPU_CFG_MASTER_ID05_MID_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID05_MID_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID05_MID_MASK -#define LPD_XPPU_CFG_MASTER_ID05_MID_DEFVAL 0x03C30081 -#define LPD_XPPU_CFG_MASTER_ID05_MID_SHIFT 0 -#define LPD_XPPU_CFG_MASTER_ID05_MID_MASK 0x000003FFU - -/*If set, only read transactions are allowed for the masters matching this register*/ -#undef LPD_XPPU_CFG_MASTER_ID06_MIDR_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID06_MIDR_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID06_MIDR_MASK -#define LPD_XPPU_CFG_MASTER_ID06_MIDR_DEFVAL 0x03C30082 -#define LPD_XPPU_CFG_MASTER_ID06_MIDR_SHIFT 30 -#define LPD_XPPU_CFG_MASTER_ID06_MIDR_MASK 0x40000000U - -/*Mask to be applied before comparing*/ -#undef LPD_XPPU_CFG_MASTER_ID06_MIDM_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID06_MIDM_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID06_MIDM_MASK -#define LPD_XPPU_CFG_MASTER_ID06_MIDM_DEFVAL 0x03C30082 -#define LPD_XPPU_CFG_MASTER_ID06_MIDM_SHIFT 16 -#define LPD_XPPU_CFG_MASTER_ID06_MIDM_MASK 0x03FF0000U - -/*Predefined Master ID for A53 Core 2*/ -#undef LPD_XPPU_CFG_MASTER_ID06_MID_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID06_MID_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID06_MID_MASK -#define LPD_XPPU_CFG_MASTER_ID06_MID_DEFVAL 0x03C30082 -#define LPD_XPPU_CFG_MASTER_ID06_MID_SHIFT 0 -#define LPD_XPPU_CFG_MASTER_ID06_MID_MASK 0x000003FFU - -/*If set, only read transactions are allowed for the masters matching this register*/ -#undef LPD_XPPU_CFG_MASTER_ID07_MIDR_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID07_MIDR_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID07_MIDR_MASK -#define LPD_XPPU_CFG_MASTER_ID07_MIDR_DEFVAL 0x83C30083 -#define LPD_XPPU_CFG_MASTER_ID07_MIDR_SHIFT 30 -#define LPD_XPPU_CFG_MASTER_ID07_MIDR_MASK 0x40000000U - -/*Mask to be applied before comparing*/ -#undef LPD_XPPU_CFG_MASTER_ID07_MIDM_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID07_MIDM_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID07_MIDM_MASK -#define LPD_XPPU_CFG_MASTER_ID07_MIDM_DEFVAL 0x83C30083 -#define LPD_XPPU_CFG_MASTER_ID07_MIDM_SHIFT 16 -#define LPD_XPPU_CFG_MASTER_ID07_MIDM_MASK 0x03FF0000U - -/*Predefined Master ID for A53 Core 3*/ -#undef LPD_XPPU_CFG_MASTER_ID07_MID_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID07_MID_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID07_MID_MASK -#define LPD_XPPU_CFG_MASTER_ID07_MID_DEFVAL 0x83C30083 -#define LPD_XPPU_CFG_MASTER_ID07_MID_SHIFT 0 -#define LPD_XPPU_CFG_MASTER_ID07_MID_MASK 0x000003FFU - -/*If set, only read transactions are allowed for the masters matching this register*/ -#undef LPD_XPPU_CFG_MASTER_ID19_MIDR_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID19_MIDR_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID19_MIDR_MASK -#define LPD_XPPU_CFG_MASTER_ID19_MIDR_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_MASTER_ID19_MIDR_SHIFT 30 -#define LPD_XPPU_CFG_MASTER_ID19_MIDR_MASK 0x40000000U - -/*Mask to be applied before comparing*/ -#undef LPD_XPPU_CFG_MASTER_ID19_MIDM_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID19_MIDM_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID19_MIDM_MASK -#define LPD_XPPU_CFG_MASTER_ID19_MIDM_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_MASTER_ID19_MIDM_SHIFT 16 -#define LPD_XPPU_CFG_MASTER_ID19_MIDM_MASK 0x03FF0000U - -/*Programmable Master ID*/ -#undef LPD_XPPU_CFG_MASTER_ID19_MID_DEFVAL -#undef LPD_XPPU_CFG_MASTER_ID19_MID_SHIFT -#undef LPD_XPPU_CFG_MASTER_ID19_MID_MASK -#define LPD_XPPU_CFG_MASTER_ID19_MID_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_MASTER_ID19_MID_SHIFT 0 -#define LPD_XPPU_CFG_MASTER_ID19_MID_MASK 0x000003FFU - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_048_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_048_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_048_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_048_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_048_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_048_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_048_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_048_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_048_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_048_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_048_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_048_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_048_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_048_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_048_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_048_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_048_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_048_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_049_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_049_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_049_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_049_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_049_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_049_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_049_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_049_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_049_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_049_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_049_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_049_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_049_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_049_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_049_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_049_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_049_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_049_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_050_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_050_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_050_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_050_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_050_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_050_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_050_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_050_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_050_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_050_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_050_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_050_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_050_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_050_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_050_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_050_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_050_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_050_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_051_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_051_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_051_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_051_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_051_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_051_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_051_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_051_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_051_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_051_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_051_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_051_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_051_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_051_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_051_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_051_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_051_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_051_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_256_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_256_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_256_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_256_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_256_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_256_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_256_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_256_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_256_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_256_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_256_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_256_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_256_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_256_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_256_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_256_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_256_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_256_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_257_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_257_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_257_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_257_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_257_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_257_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_257_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_257_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_257_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_257_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_257_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_257_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_257_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_257_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_257_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_257_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_257_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_257_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_258_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_258_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_258_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_258_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_258_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_258_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_258_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_258_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_258_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_258_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_258_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_258_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_258_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_258_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_258_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_258_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_258_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_258_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_259_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_259_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_259_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_259_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_259_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_259_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_259_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_259_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_259_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_259_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_259_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_259_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_259_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_259_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_259_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_259_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_259_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_259_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_260_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_260_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_260_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_260_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_260_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_260_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_260_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_260_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_260_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_260_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_260_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_260_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_260_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_260_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_260_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_260_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_260_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_260_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_261_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_261_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_261_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_261_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_261_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_261_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_261_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_261_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_261_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_261_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_261_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_261_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_261_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_261_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_261_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_261_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_261_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_261_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_262_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_262_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_262_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_262_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_262_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_262_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_262_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_262_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_262_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_262_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_262_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_262_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_262_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_262_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_262_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_262_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_262_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_262_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_263_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_263_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_263_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_263_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_263_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_263_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_263_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_263_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_263_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_263_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_263_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_263_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_263_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_263_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_263_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_263_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_263_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_263_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_264_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_264_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_264_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_264_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_264_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_264_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_264_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_264_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_264_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_264_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_264_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_264_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_264_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_264_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_264_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_264_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_264_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_264_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_265_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_265_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_265_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_265_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_265_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_265_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_265_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_265_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_265_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_265_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_265_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_265_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_265_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_265_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_265_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_265_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_265_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_265_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_266_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_266_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_266_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_266_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_266_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_266_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_266_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_266_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_266_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_266_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_266_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_266_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_266_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_266_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_266_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_266_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_266_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_266_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_267_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_267_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_267_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_267_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_267_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_267_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_267_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_267_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_267_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_267_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_267_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_267_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_267_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_267_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_267_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_267_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_267_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_267_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_268_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_268_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_268_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_268_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_268_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_268_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_268_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_268_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_268_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_268_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_268_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_268_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_268_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_268_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_268_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_268_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_268_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_268_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_269_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_269_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_269_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_269_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_269_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_269_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_269_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_269_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_269_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_269_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_269_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_269_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_269_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_269_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_269_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_269_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_269_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_269_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_270_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_270_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_270_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_270_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_270_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_270_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_270_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_270_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_270_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_270_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_270_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_270_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_270_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_270_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_270_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_270_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_270_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_270_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_271_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_271_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_271_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_271_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_271_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_271_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_271_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_271_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_271_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_271_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_271_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_271_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_271_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_271_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_271_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_271_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_271_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_271_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_272_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_272_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_272_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_272_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_272_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_272_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_272_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_272_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_272_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_272_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_272_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_272_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_272_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_272_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_272_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_272_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_272_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_272_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_273_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_273_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_273_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_273_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_273_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_273_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_273_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_273_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_273_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_273_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_273_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_273_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_273_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_273_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_273_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_273_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_273_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_273_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_274_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_274_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_274_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_274_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_274_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_274_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_274_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_274_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_274_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_274_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_274_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_274_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_274_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_274_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_274_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_274_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_274_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_274_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_275_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_275_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_275_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_275_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_275_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_275_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_275_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_275_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_275_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_275_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_275_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_275_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_275_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_275_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_275_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_275_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_275_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_275_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_276_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_276_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_276_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_276_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_276_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_276_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_276_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_276_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_276_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_276_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_276_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_276_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_276_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_276_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_276_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_276_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_276_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_276_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_277_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_277_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_277_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_277_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_277_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_277_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_277_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_277_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_277_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_277_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_277_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_277_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_277_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_277_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_277_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_277_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_277_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_277_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_278_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_278_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_278_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_278_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_278_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_278_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_278_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_278_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_278_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_278_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_278_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_278_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_278_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_278_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_278_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_278_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_278_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_278_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_279_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_279_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_279_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_279_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_279_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_279_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_279_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_279_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_279_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_279_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_279_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_279_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_279_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_279_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_279_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_279_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_279_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_279_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_280_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_280_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_280_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_280_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_280_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_280_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_280_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_280_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_280_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_280_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_280_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_280_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_280_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_280_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_280_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_280_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_280_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_280_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_281_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_281_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_281_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_281_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_281_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_281_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_281_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_281_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_281_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_281_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_281_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_281_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_281_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_281_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_281_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_281_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_281_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_281_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_282_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_282_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_282_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_282_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_282_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_282_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_282_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_282_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_282_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_282_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_282_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_282_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_282_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_282_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_282_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_282_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_282_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_282_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_283_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_283_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_283_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_283_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_283_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_283_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_283_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_283_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_283_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_283_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_283_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_283_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_283_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_283_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_283_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_283_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_283_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_283_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_284_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_284_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_284_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_284_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_284_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_284_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_284_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_284_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_284_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_284_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_284_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_284_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_284_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_284_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_284_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_284_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_284_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_284_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_285_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_285_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_285_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_285_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_285_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_285_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_285_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_285_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_285_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_285_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_285_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_285_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_285_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_285_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_285_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_285_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_285_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_285_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_286_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_286_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_286_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_286_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_286_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_286_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_286_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_286_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_286_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_286_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_286_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_286_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_286_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_286_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_286_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_286_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_286_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_286_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_287_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_287_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_287_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_287_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_287_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_287_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_287_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_287_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_287_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_287_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_287_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_287_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_287_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_287_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_287_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_287_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_287_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_287_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_288_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_288_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_288_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_288_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_288_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_288_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_288_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_288_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_288_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_288_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_288_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_288_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_288_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_288_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_288_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_288_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_288_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_288_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_289_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_289_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_289_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_289_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_289_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_289_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_289_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_289_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_289_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_289_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_289_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_289_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_289_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_289_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_289_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_289_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_289_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_289_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_290_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_290_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_290_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_290_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_290_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_290_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_290_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_290_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_290_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_290_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_290_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_290_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_290_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_290_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_290_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_290_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_290_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_290_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_291_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_291_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_291_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_291_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_291_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_291_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_291_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_291_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_291_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_291_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_291_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_291_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_291_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_291_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_291_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_291_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_291_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_291_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_292_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_292_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_292_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_292_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_292_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_292_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_292_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_292_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_292_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_292_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_292_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_292_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_292_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_292_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_292_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_292_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_292_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_292_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_293_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_293_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_293_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_293_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_293_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_293_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_293_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_293_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_293_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_293_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_293_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_293_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_293_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_293_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_293_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_293_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_293_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_293_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_294_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_294_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_294_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_294_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_294_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_294_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_294_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_294_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_294_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_294_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_294_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_294_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_294_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_294_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_294_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_294_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_294_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_294_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_295_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_295_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_295_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_295_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_295_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_295_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_295_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_295_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_295_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_295_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_295_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_295_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_295_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_295_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_295_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_295_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_295_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_295_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_296_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_296_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_296_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_296_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_296_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_296_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_296_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_296_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_296_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_296_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_296_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_296_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_296_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_296_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_296_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_296_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_296_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_296_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_297_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_297_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_297_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_297_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_297_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_297_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_297_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_297_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_297_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_297_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_297_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_297_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_297_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_297_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_297_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_297_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_297_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_297_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_298_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_298_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_298_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_298_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_298_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_298_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_298_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_298_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_298_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_298_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_298_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_298_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_298_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_298_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_298_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_298_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_298_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_298_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_299_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_299_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_299_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_299_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_299_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_299_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_299_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_299_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_299_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_299_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_299_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_299_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_299_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_299_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_299_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_299_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_299_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_299_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_300_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_300_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_300_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_300_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_300_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_300_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_300_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_300_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_300_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_300_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_300_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_300_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_300_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_300_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_300_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_300_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_300_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_300_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_301_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_301_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_301_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_301_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_301_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_301_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_301_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_301_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_301_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_301_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_301_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_301_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_301_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_301_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_301_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_301_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_301_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_301_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_302_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_302_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_302_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_302_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_302_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_302_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_302_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_302_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_302_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_302_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_302_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_302_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_302_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_302_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_302_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_302_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_302_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_302_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_303_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_303_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_303_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_303_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_303_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_303_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_303_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_303_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_303_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_303_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_303_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_303_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_303_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_303_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_303_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_303_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_303_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_303_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_304_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_304_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_304_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_304_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_304_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_304_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_304_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_304_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_304_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_304_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_304_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_304_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_304_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_304_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_304_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_304_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_304_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_304_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_305_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_305_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_305_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_305_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_305_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_305_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_305_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_305_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_305_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_305_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_305_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_305_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_305_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_305_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_305_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_305_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_305_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_305_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_306_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_306_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_306_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_306_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_306_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_306_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_306_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_306_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_306_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_306_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_306_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_306_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_306_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_306_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_306_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_306_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_306_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_306_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_307_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_307_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_307_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_307_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_307_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_307_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_307_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_307_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_307_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_307_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_307_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_307_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_307_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_307_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_307_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_307_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_307_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_307_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_308_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_308_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_308_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_308_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_308_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_308_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_308_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_308_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_308_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_308_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_308_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_308_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_308_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_308_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_308_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_308_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_308_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_308_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_309_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_309_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_309_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_309_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_309_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_309_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_309_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_309_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_309_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_309_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_309_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_309_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_309_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_309_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_309_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_309_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_309_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_309_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_318_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_318_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_318_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_318_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_318_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_318_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_318_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_318_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_318_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_318_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_318_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_318_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_318_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_318_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_318_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_318_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_318_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_318_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_319_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_319_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_319_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_319_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_319_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_319_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_319_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_319_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_319_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_319_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_319_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_319_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_319_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_319_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_319_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_319_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_319_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_319_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_320_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_320_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_320_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_320_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_320_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_320_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_320_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_320_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_320_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_320_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_320_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_320_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_320_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_320_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_320_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_320_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_320_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_320_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_321_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_321_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_321_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_321_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_321_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_321_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_321_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_321_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_321_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_321_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_321_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_321_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_321_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_321_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_321_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_321_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_321_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_321_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_322_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_322_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_322_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_322_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_322_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_322_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_322_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_322_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_322_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_322_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_322_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_322_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_322_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_322_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_322_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_322_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_322_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_322_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_323_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_323_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_323_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_323_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_323_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_323_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_323_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_323_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_323_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_323_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_323_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_323_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_323_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_323_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_323_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_323_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_323_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_323_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_324_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_324_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_324_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_324_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_324_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_324_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_324_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_324_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_324_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_324_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_324_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_324_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_324_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_324_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_324_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_324_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_324_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_324_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_325_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_325_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_325_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_325_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_325_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_325_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_325_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_325_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_325_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_325_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_325_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_325_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_325_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_325_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_325_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_325_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_325_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_325_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_334_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_334_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_334_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_334_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_334_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_334_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_334_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_334_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_334_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_334_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_334_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_334_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_334_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_334_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_334_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_334_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_334_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_334_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_335_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_335_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_335_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_335_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_335_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_335_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_335_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_335_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_335_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_335_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_335_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_335_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_335_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_335_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_335_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_335_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_335_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_335_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_336_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_336_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_336_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_336_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_336_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_336_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_336_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_336_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_336_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_336_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_336_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_336_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_336_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_336_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_336_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_336_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_336_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_336_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_337_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_337_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_337_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_337_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_337_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_337_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_337_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_337_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_337_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_337_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_337_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_337_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_337_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_337_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_337_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_337_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_337_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_337_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_338_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_338_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_338_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_338_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_338_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_338_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_338_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_338_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_338_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_338_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_338_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_338_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_338_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_338_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_338_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_338_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_338_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_338_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_339_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_339_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_339_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_339_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_339_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_339_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_339_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_339_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_339_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_339_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_339_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_339_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_339_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_339_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_339_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_339_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_339_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_339_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_340_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_340_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_340_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_340_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_340_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_340_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_340_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_340_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_340_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_340_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_340_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_340_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_340_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_340_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_340_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_340_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_340_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_340_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_341_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_341_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_341_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_341_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_341_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_341_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_341_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_341_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_341_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_341_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_341_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_341_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_341_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_341_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_341_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_341_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_341_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_341_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_350_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_350_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_350_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_350_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_350_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_350_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_350_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_350_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_350_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_350_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_350_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_350_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_350_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_350_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_350_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_350_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_350_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_350_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_351_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_351_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_351_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_351_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_351_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_351_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_351_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_351_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_351_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_351_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_351_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_351_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_351_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_351_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_351_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_351_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_351_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_351_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_352_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_352_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_352_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_352_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_352_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_352_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_352_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_352_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_352_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_352_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_352_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_352_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_352_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_352_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_352_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_352_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_352_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_352_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_353_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_353_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_353_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_353_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_353_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_353_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_353_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_353_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_353_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_353_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_353_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_353_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_353_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_353_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_353_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_353_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_353_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_353_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_354_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_354_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_354_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_354_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_354_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_354_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_354_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_354_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_354_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_354_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_354_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_354_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_354_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_354_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_354_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_354_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_354_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_354_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_355_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_355_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_355_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_355_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_355_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_355_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_355_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_355_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_355_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_355_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_355_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_355_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_355_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_355_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_355_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_355_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_355_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_355_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_356_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_356_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_356_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_356_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_356_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_356_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_356_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_356_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_356_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_356_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_356_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_356_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_356_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_356_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_356_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_356_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_356_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_356_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_357_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_357_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_357_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_357_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_357_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_357_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_357_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_357_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_357_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_357_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_357_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_357_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_357_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_357_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_357_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_357_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_357_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_357_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_366_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_366_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_366_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_366_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_366_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_366_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_366_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_366_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_366_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_366_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_366_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_366_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_366_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_366_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_366_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_366_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_366_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_366_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_367_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_367_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_367_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_367_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_367_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_367_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_367_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_367_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_367_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_367_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_367_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_367_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_367_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_367_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_367_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_367_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_367_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_367_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_368_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_368_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_368_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_368_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_368_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_368_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_368_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_368_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_368_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_368_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_368_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_368_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_368_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_368_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_368_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_368_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_368_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_368_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_369_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_369_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_369_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_369_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_369_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_369_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_369_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_369_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_369_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_369_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_369_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_369_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_369_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_369_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_369_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_369_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_369_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_369_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_370_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_370_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_370_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_370_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_370_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_370_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_370_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_370_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_370_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_370_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_370_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_370_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_370_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_370_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_370_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_370_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_370_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_370_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_371_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_371_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_371_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_371_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_371_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_371_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_371_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_371_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_371_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_371_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_371_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_371_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_371_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_371_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_371_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_371_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_371_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_371_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_372_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_372_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_372_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_372_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_372_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_372_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_372_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_372_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_372_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_372_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_372_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_372_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_372_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_372_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_372_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_372_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_372_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_372_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_373_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_373_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_373_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_373_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_373_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_373_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_373_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_373_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_373_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_373_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_373_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_373_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_373_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_373_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_373_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_373_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_373_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_373_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_374_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_374_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_374_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_374_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_374_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_374_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_374_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_374_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_374_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_374_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_374_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_374_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_374_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_374_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_374_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_374_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_374_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_374_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_375_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_375_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_375_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_375_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_375_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_375_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_375_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_375_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_375_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_375_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_375_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_375_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_375_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_375_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_375_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_375_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_375_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_375_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_376_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_376_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_376_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_376_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_376_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_376_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_376_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_376_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_376_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_376_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_376_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_376_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_376_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_376_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_376_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_376_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_376_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_376_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_377_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_377_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_377_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_377_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_377_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_377_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_377_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_377_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_377_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_377_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_377_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_377_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_377_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_377_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_377_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_377_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_377_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_377_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_378_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_378_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_378_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_378_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_378_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_378_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_378_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_378_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_378_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_378_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_378_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_378_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_378_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_378_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_378_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_378_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_378_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_378_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_379_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_379_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_379_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_379_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_379_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_379_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_379_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_379_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_379_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_379_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_379_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_379_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_379_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_379_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_379_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_379_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_379_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_379_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_380_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_380_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_380_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_380_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_380_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_380_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_380_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_380_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_380_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_380_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_380_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_380_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_380_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_380_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_380_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_380_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_380_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_380_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_381_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_381_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_381_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_381_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_381_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_381_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_381_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_381_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_381_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_381_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_381_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_381_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_381_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_381_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_381_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_381_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_381_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_381_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_382_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_382_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_382_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_382_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_382_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_382_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_382_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_382_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_382_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_382_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_382_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_382_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_382_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_382_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_382_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_382_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_382_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_382_PARITY_MASK 0xF0000000U - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_383_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_383_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_383_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_383_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_383_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_383_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_383_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_383_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_383_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_383_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_383_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_383_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_383_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_383_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_383_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_383_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_383_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_383_PARITY_MASK 0xF0000000U - -/*Whether an APB access to the "hole" region and to an unimplemented register space causes PSLVERR*/ -#undef LPD_XPPU_SINK_ERR_CTRL_PSLVERR_DEFVAL -#undef LPD_XPPU_SINK_ERR_CTRL_PSLVERR_SHIFT -#undef LPD_XPPU_SINK_ERR_CTRL_PSLVERR_MASK -#define LPD_XPPU_SINK_ERR_CTRL_PSLVERR_DEFVAL 0x00000000 -#define LPD_XPPU_SINK_ERR_CTRL_PSLVERR_SHIFT 0 -#define LPD_XPPU_SINK_ERR_CTRL_PSLVERR_MASK 0x00000001U - -/*0=Bypass XPPU (transparent) 1=Enable XPPU permission checking*/ -#undef LPD_XPPU_CFG_CTRL_ENABLE_DEFVAL -#undef LPD_XPPU_CFG_CTRL_ENABLE_SHIFT -#undef LPD_XPPU_CFG_CTRL_ENABLE_MASK -#define LPD_XPPU_CFG_CTRL_ENABLE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_CTRL_ENABLE_SHIFT 0 -#define LPD_XPPU_CFG_CTRL_ENABLE_MASK 0x00000001U - -/*See Interuppt Status Register for details*/ -#undef LPD_XPPU_CFG_IEN_APER_PARITY_DEFVAL -#undef LPD_XPPU_CFG_IEN_APER_PARITY_SHIFT -#undef LPD_XPPU_CFG_IEN_APER_PARITY_MASK -#define LPD_XPPU_CFG_IEN_APER_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_IEN_APER_PARITY_SHIFT 7 -#define LPD_XPPU_CFG_IEN_APER_PARITY_MASK 0x00000080U - -/*See Interuppt Status Register for details*/ -#undef LPD_XPPU_CFG_IEN_APER_TZ_DEFVAL -#undef LPD_XPPU_CFG_IEN_APER_TZ_SHIFT -#undef LPD_XPPU_CFG_IEN_APER_TZ_MASK -#define LPD_XPPU_CFG_IEN_APER_TZ_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_IEN_APER_TZ_SHIFT 6 -#define LPD_XPPU_CFG_IEN_APER_TZ_MASK 0x00000040U - -/*See Interuppt Status Register for details*/ -#undef LPD_XPPU_CFG_IEN_APER_PERM_DEFVAL -#undef LPD_XPPU_CFG_IEN_APER_PERM_SHIFT -#undef LPD_XPPU_CFG_IEN_APER_PERM_MASK -#define LPD_XPPU_CFG_IEN_APER_PERM_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_IEN_APER_PERM_SHIFT 5 -#define LPD_XPPU_CFG_IEN_APER_PERM_MASK 0x00000020U - -/*See Interuppt Status Register for details*/ -#undef LPD_XPPU_CFG_IEN_MID_PARITY_DEFVAL -#undef LPD_XPPU_CFG_IEN_MID_PARITY_SHIFT -#undef LPD_XPPU_CFG_IEN_MID_PARITY_MASK -#define LPD_XPPU_CFG_IEN_MID_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_IEN_MID_PARITY_SHIFT 3 -#define LPD_XPPU_CFG_IEN_MID_PARITY_MASK 0x00000008U - -/*See Interuppt Status Register for details*/ -#undef LPD_XPPU_CFG_IEN_MID_RO_DEFVAL -#undef LPD_XPPU_CFG_IEN_MID_RO_SHIFT -#undef LPD_XPPU_CFG_IEN_MID_RO_MASK -#define LPD_XPPU_CFG_IEN_MID_RO_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_IEN_MID_RO_SHIFT 2 -#define LPD_XPPU_CFG_IEN_MID_RO_MASK 0x00000004U - -/*See Interuppt Status Register for details*/ -#undef LPD_XPPU_CFG_IEN_MID_MISS_DEFVAL -#undef LPD_XPPU_CFG_IEN_MID_MISS_SHIFT -#undef LPD_XPPU_CFG_IEN_MID_MISS_MASK -#define LPD_XPPU_CFG_IEN_MID_MISS_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_IEN_MID_MISS_SHIFT 1 -#define LPD_XPPU_CFG_IEN_MID_MISS_MASK 0x00000002U - -/*See Interuppt Status Register for details*/ -#undef LPD_XPPU_CFG_IEN_INV_APB_DEFVAL -#undef LPD_XPPU_CFG_IEN_INV_APB_SHIFT -#undef LPD_XPPU_CFG_IEN_INV_APB_MASK -#define LPD_XPPU_CFG_IEN_INV_APB_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_IEN_INV_APB_SHIFT 0 -#define LPD_XPPU_CFG_IEN_INV_APB_MASK 0x00000001U -#undef LPD_XPPU_CFG_APERPERM_152_OFFSET -#define LPD_XPPU_CFG_APERPERM_152_OFFSET 0XFF981260 - -/*This field defines the MASTER ID match criteria. Each entry in the IDL corresponds to a bit in this field. 0=not match, 1=mat - h.*/ -#undef LPD_XPPU_CFG_APERPERM_152_PERMISSION_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_152_PERMISSION_SHIFT -#undef LPD_XPPU_CFG_APERPERM_152_PERMISSION_MASK -#define LPD_XPPU_CFG_APERPERM_152_PERMISSION_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_152_PERMISSION_SHIFT 0 -#define LPD_XPPU_CFG_APERPERM_152_PERMISSION_MASK 0x000FFFFFU - -/*1=secure or non-secure transactions are allowed 0=only secure transactiona are allowed*/ -#undef LPD_XPPU_CFG_APERPERM_152_TRUSTZONE_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_152_TRUSTZONE_SHIFT -#undef LPD_XPPU_CFG_APERPERM_152_TRUSTZONE_MASK -#define LPD_XPPU_CFG_APERPERM_152_TRUSTZONE_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_152_TRUSTZONE_SHIFT 27 -#define LPD_XPPU_CFG_APERPERM_152_TRUSTZONE_MASK 0x08000000U - -/*SW must calculate and set up parity, if parity check is enabled by the CTRL register. 31: parity for bits 19:15 30: parity fo - bits 14:10 29: parity for bits 9:5 28: parity for bits 27, 4:0*/ -#undef LPD_XPPU_CFG_APERPERM_152_PARITY_DEFVAL -#undef LPD_XPPU_CFG_APERPERM_152_PARITY_SHIFT -#undef LPD_XPPU_CFG_APERPERM_152_PARITY_MASK -#define LPD_XPPU_CFG_APERPERM_152_PARITY_DEFVAL 0x00000000 -#define LPD_XPPU_CFG_APERPERM_152_PARITY_SHIFT 28 -#define LPD_XPPU_CFG_APERPERM_152_PARITY_MASK 0xF0000000U -#undef SERDES_PLL_REF_SEL0_OFFSET -#define SERDES_PLL_REF_SEL0_OFFSET 0XFD410000 -#undef SERDES_PLL_REF_SEL1_OFFSET -#define SERDES_PLL_REF_SEL1_OFFSET 0XFD410004 -#undef SERDES_PLL_REF_SEL2_OFFSET -#define SERDES_PLL_REF_SEL2_OFFSET 0XFD410008 -#undef SERDES_PLL_REF_SEL3_OFFSET -#define SERDES_PLL_REF_SEL3_OFFSET 0XFD41000C -#undef SERDES_L0_L0_REF_CLK_SEL_OFFSET -#define SERDES_L0_L0_REF_CLK_SEL_OFFSET 0XFD402860 -#undef SERDES_L0_L1_REF_CLK_SEL_OFFSET -#define SERDES_L0_L1_REF_CLK_SEL_OFFSET 0XFD402864 -#undef SERDES_L0_L2_REF_CLK_SEL_OFFSET -#define SERDES_L0_L2_REF_CLK_SEL_OFFSET 0XFD402868 -#undef SERDES_L0_L3_REF_CLK_SEL_OFFSET -#define SERDES_L0_L3_REF_CLK_SEL_OFFSET 0XFD40286C -#undef SERDES_L2_TM_PLL_DIG_37_OFFSET -#define SERDES_L2_TM_PLL_DIG_37_OFFSET 0XFD40A094 -#undef SERDES_L2_PLL_SS_STEPS_0_LSB_OFFSET -#define SERDES_L2_PLL_SS_STEPS_0_LSB_OFFSET 0XFD40A368 -#undef SERDES_L2_PLL_SS_STEPS_1_MSB_OFFSET -#define SERDES_L2_PLL_SS_STEPS_1_MSB_OFFSET 0XFD40A36C -#undef SERDES_L3_PLL_SS_STEPS_0_LSB_OFFSET -#define SERDES_L3_PLL_SS_STEPS_0_LSB_OFFSET 0XFD40E368 -#undef SERDES_L3_PLL_SS_STEPS_1_MSB_OFFSET -#define SERDES_L3_PLL_SS_STEPS_1_MSB_OFFSET 0XFD40E36C -#undef SERDES_L0_PLL_SS_STEPS_0_LSB_OFFSET -#define SERDES_L0_PLL_SS_STEPS_0_LSB_OFFSET 0XFD402368 -#undef SERDES_L0_PLL_SS_STEPS_1_MSB_OFFSET -#define SERDES_L0_PLL_SS_STEPS_1_MSB_OFFSET 0XFD40236C -#undef SERDES_L1_PLL_SS_STEPS_0_LSB_OFFSET -#define SERDES_L1_PLL_SS_STEPS_0_LSB_OFFSET 0XFD406368 -#undef SERDES_L1_PLL_SS_STEPS_1_MSB_OFFSET -#define SERDES_L1_PLL_SS_STEPS_1_MSB_OFFSET 0XFD40636C -#undef SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_OFFSET -#define SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_OFFSET 0XFD402370 -#undef SERDES_L0_PLL_SS_STEP_SIZE_1_OFFSET -#define SERDES_L0_PLL_SS_STEP_SIZE_1_OFFSET 0XFD402374 -#undef SERDES_L0_PLL_SS_STEP_SIZE_2_OFFSET -#define SERDES_L0_PLL_SS_STEP_SIZE_2_OFFSET 0XFD402378 -#undef SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_OFFSET -#define SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_OFFSET 0XFD40237C -#undef SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_OFFSET -#define SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_OFFSET 0XFD406370 -#undef SERDES_L1_PLL_SS_STEP_SIZE_1_OFFSET -#define SERDES_L1_PLL_SS_STEP_SIZE_1_OFFSET 0XFD406374 -#undef SERDES_L1_PLL_SS_STEP_SIZE_2_OFFSET -#define SERDES_L1_PLL_SS_STEP_SIZE_2_OFFSET 0XFD406378 -#undef SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_OFFSET -#define SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_OFFSET 0XFD40637C -#undef SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_OFFSET -#define SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_OFFSET 0XFD40A370 -#undef SERDES_L2_PLL_SS_STEP_SIZE_1_OFFSET -#define SERDES_L2_PLL_SS_STEP_SIZE_1_OFFSET 0XFD40A374 -#undef SERDES_L2_PLL_SS_STEP_SIZE_2_OFFSET -#define SERDES_L2_PLL_SS_STEP_SIZE_2_OFFSET 0XFD40A378 -#undef SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_OFFSET -#define SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_OFFSET 0XFD40A37C -#undef SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_OFFSET -#define SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_OFFSET 0XFD40E370 -#undef SERDES_L3_PLL_SS_STEP_SIZE_1_OFFSET -#define SERDES_L3_PLL_SS_STEP_SIZE_1_OFFSET 0XFD40E374 -#undef SERDES_L3_PLL_SS_STEP_SIZE_2_OFFSET -#define SERDES_L3_PLL_SS_STEP_SIZE_2_OFFSET 0XFD40E378 -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_OFFSET -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_OFFSET 0XFD40E37C -#undef SERDES_L2_TM_DIG_6_OFFSET -#define SERDES_L2_TM_DIG_6_OFFSET 0XFD40906C -#undef SERDES_L2_TX_DIG_TM_61_OFFSET -#define SERDES_L2_TX_DIG_TM_61_OFFSET 0XFD4080F4 -#undef SERDES_L3_PLL_FBDIV_FRAC_3_MSB_OFFSET -#define SERDES_L3_PLL_FBDIV_FRAC_3_MSB_OFFSET 0XFD40E360 -#undef SERDES_L3_TM_DIG_6_OFFSET -#define SERDES_L3_TM_DIG_6_OFFSET 0XFD40D06C -#undef SERDES_L3_TX_DIG_TM_61_OFFSET -#define SERDES_L3_TX_DIG_TM_61_OFFSET 0XFD40C0F4 -#undef SERDES_L3_TXPMA_ST_0_OFFSET -#define SERDES_L3_TXPMA_ST_0_OFFSET 0XFD40CB00 -#undef SERDES_L2_TM_AUX_0_OFFSET -#define SERDES_L2_TM_AUX_0_OFFSET 0XFD4090CC -#undef SERDES_L0_TM_DIG_8_OFFSET -#define SERDES_L0_TM_DIG_8_OFFSET 0XFD401074 -#undef SERDES_L1_TM_DIG_8_OFFSET -#define SERDES_L1_TM_DIG_8_OFFSET 0XFD405074 -#undef SERDES_L2_TM_DIG_8_OFFSET -#define SERDES_L2_TM_DIG_8_OFFSET 0XFD409074 -#undef SERDES_L3_TM_DIG_8_OFFSET -#define SERDES_L3_TM_DIG_8_OFFSET 0XFD40D074 -#undef SERDES_L2_TM_MISC2_OFFSET -#define SERDES_L2_TM_MISC2_OFFSET 0XFD40989C -#undef SERDES_L2_TM_IQ_ILL1_OFFSET -#define SERDES_L2_TM_IQ_ILL1_OFFSET 0XFD4098F8 -#undef SERDES_L2_TM_IQ_ILL2_OFFSET -#define SERDES_L2_TM_IQ_ILL2_OFFSET 0XFD4098FC -#undef SERDES_L2_TM_ILL12_OFFSET -#define SERDES_L2_TM_ILL12_OFFSET 0XFD409990 -#undef SERDES_L2_TM_E_ILL1_OFFSET -#define SERDES_L2_TM_E_ILL1_OFFSET 0XFD409924 -#undef SERDES_L2_TM_E_ILL2_OFFSET -#define SERDES_L2_TM_E_ILL2_OFFSET 0XFD409928 -#undef SERDES_L2_TM_IQ_ILL3_OFFSET -#define SERDES_L2_TM_IQ_ILL3_OFFSET 0XFD409900 -#undef SERDES_L2_TM_E_ILL3_OFFSET -#define SERDES_L2_TM_E_ILL3_OFFSET 0XFD40992C -#undef SERDES_L2_TM_ILL8_OFFSET -#define SERDES_L2_TM_ILL8_OFFSET 0XFD409980 -#undef SERDES_L2_TM_IQ_ILL8_OFFSET -#define SERDES_L2_TM_IQ_ILL8_OFFSET 0XFD409914 -#undef SERDES_L2_TM_IQ_ILL9_OFFSET -#define SERDES_L2_TM_IQ_ILL9_OFFSET 0XFD409918 -#undef SERDES_L2_TM_E_ILL8_OFFSET -#define SERDES_L2_TM_E_ILL8_OFFSET 0XFD409940 -#undef SERDES_L2_TM_E_ILL9_OFFSET -#define SERDES_L2_TM_E_ILL9_OFFSET 0XFD409944 -#undef SERDES_L3_TM_MISC2_OFFSET -#define SERDES_L3_TM_MISC2_OFFSET 0XFD40D89C -#undef SERDES_L3_TM_IQ_ILL1_OFFSET -#define SERDES_L3_TM_IQ_ILL1_OFFSET 0XFD40D8F8 -#undef SERDES_L3_TM_IQ_ILL2_OFFSET -#define SERDES_L3_TM_IQ_ILL2_OFFSET 0XFD40D8FC -#undef SERDES_L3_TM_ILL12_OFFSET -#define SERDES_L3_TM_ILL12_OFFSET 0XFD40D990 -#undef SERDES_L3_TM_E_ILL1_OFFSET -#define SERDES_L3_TM_E_ILL1_OFFSET 0XFD40D924 -#undef SERDES_L3_TM_E_ILL2_OFFSET -#define SERDES_L3_TM_E_ILL2_OFFSET 0XFD40D928 -#undef SERDES_L3_TM_ILL11_OFFSET -#define SERDES_L3_TM_ILL11_OFFSET 0XFD40D98C -#undef SERDES_L3_TM_IQ_ILL3_OFFSET -#define SERDES_L3_TM_IQ_ILL3_OFFSET 0XFD40D900 -#undef SERDES_L3_TM_E_ILL3_OFFSET -#define SERDES_L3_TM_E_ILL3_OFFSET 0XFD40D92C -#undef SERDES_L3_TM_ILL8_OFFSET -#define SERDES_L3_TM_ILL8_OFFSET 0XFD40D980 -#undef SERDES_L3_TM_IQ_ILL8_OFFSET -#define SERDES_L3_TM_IQ_ILL8_OFFSET 0XFD40D914 -#undef SERDES_L3_TM_IQ_ILL9_OFFSET -#define SERDES_L3_TM_IQ_ILL9_OFFSET 0XFD40D918 -#undef SERDES_L3_TM_E_ILL8_OFFSET -#define SERDES_L3_TM_E_ILL8_OFFSET 0XFD40D940 -#undef SERDES_L3_TM_E_ILL9_OFFSET -#define SERDES_L3_TM_E_ILL9_OFFSET 0XFD40D944 -#undef SERDES_L0_TM_RST_DLY_OFFSET -#define SERDES_L0_TM_RST_DLY_OFFSET 0XFD4019A4 -#undef SERDES_L0_TM_ANA_BYP_15_OFFSET -#define SERDES_L0_TM_ANA_BYP_15_OFFSET 0XFD401038 -#undef SERDES_L0_TM_ANA_BYP_12_OFFSET -#define SERDES_L0_TM_ANA_BYP_12_OFFSET 0XFD40102C -#undef SERDES_L1_TM_RST_DLY_OFFSET -#define SERDES_L1_TM_RST_DLY_OFFSET 0XFD4059A4 -#undef SERDES_L1_TM_ANA_BYP_15_OFFSET -#define SERDES_L1_TM_ANA_BYP_15_OFFSET 0XFD405038 -#undef SERDES_L1_TM_ANA_BYP_12_OFFSET -#define SERDES_L1_TM_ANA_BYP_12_OFFSET 0XFD40502C -#undef SERDES_L2_TM_RST_DLY_OFFSET -#define SERDES_L2_TM_RST_DLY_OFFSET 0XFD4099A4 -#undef SERDES_L2_TM_ANA_BYP_15_OFFSET -#define SERDES_L2_TM_ANA_BYP_15_OFFSET 0XFD409038 -#undef SERDES_L2_TM_ANA_BYP_12_OFFSET -#define SERDES_L2_TM_ANA_BYP_12_OFFSET 0XFD40902C -#undef SERDES_L3_TM_RST_DLY_OFFSET -#define SERDES_L3_TM_RST_DLY_OFFSET 0XFD40D9A4 -#undef SERDES_L3_TM_ANA_BYP_15_OFFSET -#define SERDES_L3_TM_ANA_BYP_15_OFFSET 0XFD40D038 -#undef SERDES_L3_TM_ANA_BYP_12_OFFSET -#define SERDES_L3_TM_ANA_BYP_12_OFFSET 0XFD40D02C -#undef SERDES_ICM_CFG0_OFFSET -#define SERDES_ICM_CFG0_OFFSET 0XFD410010 -#undef SERDES_ICM_CFG1_OFFSET -#define SERDES_ICM_CFG1_OFFSET 0XFD410014 -#undef SERDES_L0_TXPMD_TM_45_OFFSET -#define SERDES_L0_TXPMD_TM_45_OFFSET 0XFD400CB4 -#undef SERDES_L1_TXPMD_TM_45_OFFSET -#define SERDES_L1_TXPMD_TM_45_OFFSET 0XFD404CB4 -#undef SERDES_L0_TX_ANA_TM_118_OFFSET -#define SERDES_L0_TX_ANA_TM_118_OFFSET 0XFD4001D8 -#undef SERDES_L1_TX_ANA_TM_118_OFFSET -#define SERDES_L1_TX_ANA_TM_118_OFFSET 0XFD4041D8 -#undef SERDES_L3_TX_ANA_TM_118_OFFSET -#define SERDES_L3_TX_ANA_TM_118_OFFSET 0XFD40C1D8 -#undef SERDES_L3_TM_CDR5_OFFSET -#define SERDES_L3_TM_CDR5_OFFSET 0XFD40DC14 -#undef SERDES_L3_TM_CDR16_OFFSET -#define SERDES_L3_TM_CDR16_OFFSET 0XFD40DC40 -#undef SERDES_L3_TM_EQ0_OFFSET -#define SERDES_L3_TM_EQ0_OFFSET 0XFD40D94C -#undef SERDES_L3_TM_EQ1_OFFSET -#define SERDES_L3_TM_EQ1_OFFSET 0XFD40D950 -#undef SERDES_L1_TXPMD_TM_48_OFFSET -#define SERDES_L1_TXPMD_TM_48_OFFSET 0XFD404CC0 -#undef SERDES_L0_TXPMD_TM_48_OFFSET -#define SERDES_L0_TXPMD_TM_48_OFFSET 0XFD400CC0 -#undef SERDES_L1_TX_ANA_TM_18_OFFSET -#define SERDES_L1_TX_ANA_TM_18_OFFSET 0XFD404048 -#undef SERDES_L0_TX_ANA_TM_18_OFFSET -#define SERDES_L0_TX_ANA_TM_18_OFFSET 0XFD400048 -#undef SERDES_L3_TX_ANA_TM_18_OFFSET -#define SERDES_L3_TX_ANA_TM_18_OFFSET 0XFD40C048 - -/*PLL0 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - - 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135 - Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved*/ -#undef SERDES_PLL_REF_SEL0_PLLREFSEL0_DEFVAL -#undef SERDES_PLL_REF_SEL0_PLLREFSEL0_SHIFT -#undef SERDES_PLL_REF_SEL0_PLLREFSEL0_MASK -#define SERDES_PLL_REF_SEL0_PLLREFSEL0_DEFVAL 0x0000000D -#define SERDES_PLL_REF_SEL0_PLLREFSEL0_SHIFT 0 -#define SERDES_PLL_REF_SEL0_PLLREFSEL0_MASK 0x0000001FU - -/*PLL1 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - - 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135 - Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved*/ -#undef SERDES_PLL_REF_SEL1_PLLREFSEL1_DEFVAL -#undef SERDES_PLL_REF_SEL1_PLLREFSEL1_SHIFT -#undef SERDES_PLL_REF_SEL1_PLLREFSEL1_MASK -#define SERDES_PLL_REF_SEL1_PLLREFSEL1_DEFVAL 0x00000008 -#define SERDES_PLL_REF_SEL1_PLLREFSEL1_SHIFT 0 -#define SERDES_PLL_REF_SEL1_PLLREFSEL1_MASK 0x0000001FU - -/*PLL2 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - - 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135 - Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved*/ -#undef SERDES_PLL_REF_SEL2_PLLREFSEL2_DEFVAL -#undef SERDES_PLL_REF_SEL2_PLLREFSEL2_SHIFT -#undef SERDES_PLL_REF_SEL2_PLLREFSEL2_MASK -#define SERDES_PLL_REF_SEL2_PLLREFSEL2_DEFVAL 0x0000000F -#define SERDES_PLL_REF_SEL2_PLLREFSEL2_SHIFT 0 -#define SERDES_PLL_REF_SEL2_PLLREFSEL2_MASK 0x0000001FU - -/*PLL3 Reference Selection. 0x0 - 5MHz, 0x1 - 9.6MHz, 0x2 - 10MHz, 0x3 - 12MHz, 0x4 - 13MHz, 0x5 - 19.2MHz, 0x6 - 20MHz, 0x7 - - 4MHz, 0x8 - 26MHz, 0x9 - 27MHz, 0xA - 38.4MHz, 0xB - 40MHz, 0xC - 52MHz, 0xD - 100MHz, 0xE - 108MHz, 0xF - 125MHz, 0x10 - 135 - Hz, 0x11 - 150 MHz. 0x12 to 0x1F - Reserved*/ -#undef SERDES_PLL_REF_SEL3_PLLREFSEL3_DEFVAL -#undef SERDES_PLL_REF_SEL3_PLLREFSEL3_SHIFT -#undef SERDES_PLL_REF_SEL3_PLLREFSEL3_MASK -#define SERDES_PLL_REF_SEL3_PLLREFSEL3_DEFVAL 0x0000000E -#define SERDES_PLL_REF_SEL3_PLLREFSEL3_SHIFT 0 -#define SERDES_PLL_REF_SEL3_PLLREFSEL3_MASK 0x0000001FU - -/*Sel of lane 0 ref clock local mux. Set to 1 to select lane 0 slicer output. Set to 0 to select lane0 ref clock mux output.*/ -#undef SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL_DEFVAL -#undef SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL_SHIFT -#undef SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL_MASK -#define SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL_DEFVAL 0x00000080 -#define SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL_SHIFT 7 -#define SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_LCL_SEL_MASK 0x00000080U - -/*Bit 3 of lane 0 ref clock mux one hot sel. Set to 1 to select lane 3 slicer output from ref clock network*/ -#undef SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_SEL_3_DEFVAL -#undef SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_SEL_3_SHIFT -#undef SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_SEL_3_MASK -#define SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_SEL_3_DEFVAL 0x00000080 -#define SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_SEL_3_SHIFT 3 -#define SERDES_L0_L0_REF_CLK_SEL_L0_REF_CLK_SEL_3_MASK 0x00000008U - -/*Sel of lane 1 ref clock local mux. Set to 1 to select lane 1 slicer output. Set to 0 to select lane1 ref clock mux output.*/ -#undef SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL_DEFVAL -#undef SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL_SHIFT -#undef SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL_MASK -#define SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL_DEFVAL 0x00000080 -#define SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL_SHIFT 7 -#define SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_LCL_SEL_MASK 0x00000080U - -/*Bit 3 of lane 1 ref clock mux one hot sel. Set to 1 to select lane 3 slicer output from ref clock network*/ -#undef SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3_DEFVAL -#undef SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3_SHIFT -#undef SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3_MASK -#define SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3_DEFVAL 0x00000080 -#define SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3_SHIFT 3 -#define SERDES_L0_L1_REF_CLK_SEL_L1_REF_CLK_SEL_3_MASK 0x00000008U - -/*Sel of lane 2 ref clock local mux. Set to 1 to select lane 1 slicer output. Set to 0 to select lane2 ref clock mux output.*/ -#undef SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL_DEFVAL -#undef SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL_SHIFT -#undef SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL_MASK -#define SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL_DEFVAL 0x00000080 -#define SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL_SHIFT 7 -#define SERDES_L0_L2_REF_CLK_SEL_L2_REF_CLK_LCL_SEL_MASK 0x00000080U - -/*Sel of lane 3 ref clock local mux. Set to 1 to select lane 3 slicer output. Set to 0 to select lane3 ref clock mux output.*/ -#undef SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL_DEFVAL -#undef SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL_SHIFT -#undef SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL_MASK -#define SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL_DEFVAL 0x00000080 -#define SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL_SHIFT 7 -#define SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_LCL_SEL_MASK 0x00000080U - -/*Bit 1 of lane 3 ref clock mux one hot sel. Set to 1 to select lane 1 slicer output from ref clock network*/ -#undef SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1_DEFVAL -#undef SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1_SHIFT -#undef SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1_MASK -#define SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1_DEFVAL 0x00000080 -#define SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1_SHIFT 1 -#define SERDES_L0_L3_REF_CLK_SEL_L3_REF_CLK_SEL_1_MASK 0x00000002U - -/*Enable/Disable coarse code satureation limiting logic*/ -#undef SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION_DEFVAL -#undef SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION_SHIFT -#undef SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION_MASK -#define SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION_DEFVAL 0x00000000 -#define SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION_SHIFT 4 -#define SERDES_L2_TM_PLL_DIG_37_TM_ENABLE_COARSE_SATURATION_MASK 0x00000010U - -/*Spread Spectrum No of Steps [7:0]*/ -#undef SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_DEFVAL -#undef SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT -#undef SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK -#define SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_DEFVAL 0x00000000 -#define SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT 0 -#define SERDES_L2_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK 0x000000FFU - -/*Spread Spectrum No of Steps [10:8]*/ -#undef SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_DEFVAL -#undef SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT -#undef SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK -#define SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_DEFVAL 0x00000000 -#define SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT 0 -#define SERDES_L2_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK 0x00000007U - -/*Spread Spectrum No of Steps [7:0]*/ -#undef SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_DEFVAL -#undef SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT -#undef SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK -#define SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_DEFVAL 0x00000000 -#define SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT 0 -#define SERDES_L3_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK 0x000000FFU - -/*Spread Spectrum No of Steps [10:8]*/ -#undef SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_DEFVAL -#undef SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT -#undef SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK -#define SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_DEFVAL 0x00000000 -#define SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT 0 -#define SERDES_L3_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK 0x00000007U - -/*Spread Spectrum No of Steps [7:0]*/ -#undef SERDES_L0_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_DEFVAL -#undef SERDES_L0_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT -#undef SERDES_L0_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK -#define SERDES_L0_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_DEFVAL 0x00000000 -#define SERDES_L0_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT 0 -#define SERDES_L0_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK 0x000000FFU - -/*Spread Spectrum No of Steps [10:8]*/ -#undef SERDES_L0_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_DEFVAL -#undef SERDES_L0_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT -#undef SERDES_L0_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK -#define SERDES_L0_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_DEFVAL 0x00000000 -#define SERDES_L0_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT 0 -#define SERDES_L0_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK 0x00000007U - -/*Spread Spectrum No of Steps [7:0]*/ -#undef SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_DEFVAL -#undef SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT -#undef SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK -#define SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_DEFVAL 0x00000000 -#define SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_SHIFT 0 -#define SERDES_L1_PLL_SS_STEPS_0_LSB_SS_NUM_OF_STEPS_0_LSB_MASK 0x000000FFU - -/*Spread Spectrum No of Steps [10:8]*/ -#undef SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_DEFVAL -#undef SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT -#undef SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK -#define SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_DEFVAL 0x00000000 -#define SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_SHIFT 0 -#define SERDES_L1_PLL_SS_STEPS_1_MSB_SS_NUM_OF_STEPS_1_MSB_MASK 0x00000007U - -/*Step Size for Spread Spectrum [7:0]*/ -#undef SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_DEFVAL -#undef SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT -#undef SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK -#define SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_DEFVAL 0x00000000 -#define SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT 0 -#define SERDES_L0_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [15:8]*/ -#undef SERDES_L0_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_DEFVAL -#undef SERDES_L0_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT -#undef SERDES_L0_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK -#define SERDES_L0_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_DEFVAL 0x00000000 -#define SERDES_L0_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT 0 -#define SERDES_L0_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [23:16]*/ -#undef SERDES_L0_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_DEFVAL -#undef SERDES_L0_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT -#undef SERDES_L0_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK -#define SERDES_L0_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_DEFVAL 0x00000000 -#define SERDES_L0_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT 0 -#define SERDES_L0_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [25:24]*/ -#undef SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_DEFVAL -#undef SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT -#undef SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK -#define SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_DEFVAL 0x00000000 -#define SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT 0 -#define SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK 0x00000003U - -/*Enable/Disable test mode force on SS step size*/ -#undef SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_DEFVAL -#undef SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT -#undef SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK -#define SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_DEFVAL 0x00000000 -#define SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT 4 -#define SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK 0x00000010U - -/*Enable/Disable test mode force on SS no of steps*/ -#undef SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_DEFVAL -#undef SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT -#undef SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK -#define SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_DEFVAL 0x00000000 -#define SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT 5 -#define SERDES_L0_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK 0x00000020U - -/*Step Size for Spread Spectrum [7:0]*/ -#undef SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_DEFVAL -#undef SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT -#undef SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK -#define SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_DEFVAL 0x00000000 -#define SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT 0 -#define SERDES_L1_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [15:8]*/ -#undef SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_DEFVAL -#undef SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT -#undef SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK -#define SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_DEFVAL 0x00000000 -#define SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT 0 -#define SERDES_L1_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [23:16]*/ -#undef SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_DEFVAL -#undef SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT -#undef SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK -#define SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_DEFVAL 0x00000000 -#define SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT 0 -#define SERDES_L1_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [25:24]*/ -#undef SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_DEFVAL -#undef SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT -#undef SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK -#define SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_DEFVAL 0x00000000 -#define SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT 0 -#define SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK 0x00000003U - -/*Enable/Disable test mode force on SS step size*/ -#undef SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_DEFVAL -#undef SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT -#undef SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK -#define SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_DEFVAL 0x00000000 -#define SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT 4 -#define SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK 0x00000010U - -/*Enable/Disable test mode force on SS no of steps*/ -#undef SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_DEFVAL -#undef SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT -#undef SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK -#define SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_DEFVAL 0x00000000 -#define SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT 5 -#define SERDES_L1_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK 0x00000020U - -/*Step Size for Spread Spectrum [7:0]*/ -#undef SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_DEFVAL -#undef SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT -#undef SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK -#define SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_DEFVAL 0x00000000 -#define SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT 0 -#define SERDES_L2_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [15:8]*/ -#undef SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_DEFVAL -#undef SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT -#undef SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK -#define SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_DEFVAL 0x00000000 -#define SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT 0 -#define SERDES_L2_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [23:16]*/ -#undef SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_DEFVAL -#undef SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT -#undef SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK -#define SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_DEFVAL 0x00000000 -#define SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT 0 -#define SERDES_L2_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [25:24]*/ -#undef SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_DEFVAL -#undef SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT -#undef SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK -#define SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_DEFVAL 0x00000000 -#define SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT 0 -#define SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK 0x00000003U - -/*Enable/Disable test mode force on SS step size*/ -#undef SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_DEFVAL -#undef SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT -#undef SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK -#define SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_DEFVAL 0x00000000 -#define SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT 4 -#define SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK 0x00000010U - -/*Enable/Disable test mode force on SS no of steps*/ -#undef SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_DEFVAL -#undef SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT -#undef SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK -#define SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_DEFVAL 0x00000000 -#define SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT 5 -#define SERDES_L2_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK 0x00000020U - -/*Step Size for Spread Spectrum [7:0]*/ -#undef SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_DEFVAL -#undef SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT -#undef SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK -#define SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_DEFVAL 0x00000000 -#define SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_SHIFT 0 -#define SERDES_L3_PLL_SS_STEP_SIZE_0_LSB_SS_STEP_SIZE_0_LSB_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [15:8]*/ -#undef SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_DEFVAL -#undef SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT -#undef SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK -#define SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_DEFVAL 0x00000000 -#define SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_SHIFT 0 -#define SERDES_L3_PLL_SS_STEP_SIZE_1_SS_STEP_SIZE_1_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [23:16]*/ -#undef SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_DEFVAL -#undef SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT -#undef SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK -#define SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_DEFVAL 0x00000000 -#define SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_SHIFT 0 -#define SERDES_L3_PLL_SS_STEP_SIZE_2_SS_STEP_SIZE_2_MASK 0x000000FFU - -/*Step Size for Spread Spectrum [25:24]*/ -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_DEFVAL -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_DEFVAL 0x00000000 -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_SHIFT 0 -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_SS_STEP_SIZE_3_MSB_MASK 0x00000003U - -/*Enable/Disable test mode force on SS step size*/ -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_DEFVAL -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_DEFVAL 0x00000000 -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_SHIFT 4 -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_STEP_SIZE_MASK 0x00000010U - -/*Enable/Disable test mode force on SS no of steps*/ -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_DEFVAL -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_DEFVAL 0x00000000 -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_SHIFT 5 -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_FORCE_SS_NUM_OF_STEPS_MASK 0x00000020U - -/*Enable test mode forcing on enable Spread Spectrum*/ -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS_DEFVAL -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS_SHIFT -#undef SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS_MASK -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS_DEFVAL 0x00000000 -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS_SHIFT 7 -#define SERDES_L3_PLL_SS_STEP_SIZE_3_MSB_TM_FORCE_EN_SS_MASK 0x00000080U - -/*Bypass Descrambler*/ -#undef SERDES_L2_TM_DIG_6_BYPASS_DESCRAM_DEFVAL -#undef SERDES_L2_TM_DIG_6_BYPASS_DESCRAM_SHIFT -#undef SERDES_L2_TM_DIG_6_BYPASS_DESCRAM_MASK -#define SERDES_L2_TM_DIG_6_BYPASS_DESCRAM_DEFVAL 0x00000000 -#define SERDES_L2_TM_DIG_6_BYPASS_DESCRAM_SHIFT 1 -#define SERDES_L2_TM_DIG_6_BYPASS_DESCRAM_MASK 0x00000002U - -/*Enable Bypass for <1> TM_DIG_CTRL_6*/ -#undef SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM_DEFVAL -#undef SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM_SHIFT -#undef SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM_MASK -#define SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM_DEFVAL 0x00000000 -#define SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM_SHIFT 0 -#define SERDES_L2_TM_DIG_6_FORCE_BYPASS_DESCRAM_MASK 0x00000001U - -/*Bypass scrambler signal*/ -#undef SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM_DEFVAL -#undef SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM_SHIFT -#undef SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM_MASK -#define SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM_DEFVAL 0x00000000 -#define SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM_SHIFT 1 -#define SERDES_L2_TX_DIG_TM_61_BYPASS_SCRAM_MASK 0x00000002U - -/*Enable/disable scrambler bypass signal*/ -#undef SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_DEFVAL -#undef SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_SHIFT -#undef SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_MASK -#define SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_DEFVAL 0x00000000 -#define SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_SHIFT 0 -#define SERDES_L2_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_MASK 0x00000001U - -/*Enable test mode force on fractional mode enable*/ -#undef SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC_DEFVAL -#undef SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC_SHIFT -#undef SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC_MASK -#define SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC_DEFVAL 0x00000000 -#define SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC_SHIFT 6 -#define SERDES_L3_PLL_FBDIV_FRAC_3_MSB_TM_FORCE_EN_FRAC_MASK 0x00000040U - -/*Bypass 8b10b decoder*/ -#undef SERDES_L3_TM_DIG_6_BYPASS_DECODER_DEFVAL -#undef SERDES_L3_TM_DIG_6_BYPASS_DECODER_SHIFT -#undef SERDES_L3_TM_DIG_6_BYPASS_DECODER_MASK -#define SERDES_L3_TM_DIG_6_BYPASS_DECODER_DEFVAL 0x00000000 -#define SERDES_L3_TM_DIG_6_BYPASS_DECODER_SHIFT 3 -#define SERDES_L3_TM_DIG_6_BYPASS_DECODER_MASK 0x00000008U - -/*Enable Bypass for <3> TM_DIG_CTRL_6*/ -#undef SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC_DEFVAL -#undef SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC_SHIFT -#undef SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC_MASK -#define SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC_DEFVAL 0x00000000 -#define SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC_SHIFT 2 -#define SERDES_L3_TM_DIG_6_FORCE_BYPASS_DEC_MASK 0x00000004U - -/*Bypass Descrambler*/ -#undef SERDES_L3_TM_DIG_6_BYPASS_DESCRAM_DEFVAL -#undef SERDES_L3_TM_DIG_6_BYPASS_DESCRAM_SHIFT -#undef SERDES_L3_TM_DIG_6_BYPASS_DESCRAM_MASK -#define SERDES_L3_TM_DIG_6_BYPASS_DESCRAM_DEFVAL 0x00000000 -#define SERDES_L3_TM_DIG_6_BYPASS_DESCRAM_SHIFT 1 -#define SERDES_L3_TM_DIG_6_BYPASS_DESCRAM_MASK 0x00000002U - -/*Enable Bypass for <1> TM_DIG_CTRL_6*/ -#undef SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM_DEFVAL -#undef SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM_SHIFT -#undef SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM_MASK -#define SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM_DEFVAL 0x00000000 -#define SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM_SHIFT 0 -#define SERDES_L3_TM_DIG_6_FORCE_BYPASS_DESCRAM_MASK 0x00000001U - -/*Enable/disable encoder bypass signal*/ -#undef SERDES_L3_TX_DIG_TM_61_BYPASS_ENC_DEFVAL -#undef SERDES_L3_TX_DIG_TM_61_BYPASS_ENC_SHIFT -#undef SERDES_L3_TX_DIG_TM_61_BYPASS_ENC_MASK -#define SERDES_L3_TX_DIG_TM_61_BYPASS_ENC_DEFVAL 0x00000000 -#define SERDES_L3_TX_DIG_TM_61_BYPASS_ENC_SHIFT 3 -#define SERDES_L3_TX_DIG_TM_61_BYPASS_ENC_MASK 0x00000008U - -/*Bypass scrambler signal*/ -#undef SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM_DEFVAL -#undef SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM_SHIFT -#undef SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM_MASK -#define SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM_DEFVAL 0x00000000 -#define SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM_SHIFT 1 -#define SERDES_L3_TX_DIG_TM_61_BYPASS_SCRAM_MASK 0x00000002U - -/*Enable/disable scrambler bypass signal*/ -#undef SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_DEFVAL -#undef SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_SHIFT -#undef SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_MASK -#define SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_DEFVAL 0x00000000 -#define SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_SHIFT 0 -#define SERDES_L3_TX_DIG_TM_61_FORCE_BYPASS_SCRAM_MASK 0x00000001U - -/*PHY Mode: 4'b000 - PCIe, 4'b001 - USB3, 4'b0010 - SATA, 4'b0100 - SGMII, 4'b0101 - DP, 4'b1000 - MPHY*/ -#undef SERDES_L3_TXPMA_ST_0_TX_PHY_MODE_DEFVAL -#undef SERDES_L3_TXPMA_ST_0_TX_PHY_MODE_SHIFT -#undef SERDES_L3_TXPMA_ST_0_TX_PHY_MODE_MASK -#define SERDES_L3_TXPMA_ST_0_TX_PHY_MODE_DEFVAL 0x00000001 -#define SERDES_L3_TXPMA_ST_0_TX_PHY_MODE_SHIFT 4 -#define SERDES_L3_TXPMA_ST_0_TX_PHY_MODE_MASK 0x000000F0U - -/*Spare- not used*/ -#undef SERDES_L2_TM_AUX_0_BIT_2_DEFVAL -#undef SERDES_L2_TM_AUX_0_BIT_2_SHIFT -#undef SERDES_L2_TM_AUX_0_BIT_2_MASK -#define SERDES_L2_TM_AUX_0_BIT_2_DEFVAL 0x00000000 -#define SERDES_L2_TM_AUX_0_BIT_2_SHIFT 5 -#define SERDES_L2_TM_AUX_0_BIT_2_MASK 0x00000020U - -/*Enable Eye Surf*/ -#undef SERDES_L0_TM_DIG_8_EYESURF_ENABLE_DEFVAL -#undef SERDES_L0_TM_DIG_8_EYESURF_ENABLE_SHIFT -#undef SERDES_L0_TM_DIG_8_EYESURF_ENABLE_MASK -#define SERDES_L0_TM_DIG_8_EYESURF_ENABLE_DEFVAL 0x00000000 -#define SERDES_L0_TM_DIG_8_EYESURF_ENABLE_SHIFT 4 -#define SERDES_L0_TM_DIG_8_EYESURF_ENABLE_MASK 0x00000010U - -/*Enable Eye Surf*/ -#undef SERDES_L1_TM_DIG_8_EYESURF_ENABLE_DEFVAL -#undef SERDES_L1_TM_DIG_8_EYESURF_ENABLE_SHIFT -#undef SERDES_L1_TM_DIG_8_EYESURF_ENABLE_MASK -#define SERDES_L1_TM_DIG_8_EYESURF_ENABLE_DEFVAL 0x00000000 -#define SERDES_L1_TM_DIG_8_EYESURF_ENABLE_SHIFT 4 -#define SERDES_L1_TM_DIG_8_EYESURF_ENABLE_MASK 0x00000010U - -/*Enable Eye Surf*/ -#undef SERDES_L2_TM_DIG_8_EYESURF_ENABLE_DEFVAL -#undef SERDES_L2_TM_DIG_8_EYESURF_ENABLE_SHIFT -#undef SERDES_L2_TM_DIG_8_EYESURF_ENABLE_MASK -#define SERDES_L2_TM_DIG_8_EYESURF_ENABLE_DEFVAL 0x00000000 -#define SERDES_L2_TM_DIG_8_EYESURF_ENABLE_SHIFT 4 -#define SERDES_L2_TM_DIG_8_EYESURF_ENABLE_MASK 0x00000010U - -/*Enable Eye Surf*/ -#undef SERDES_L3_TM_DIG_8_EYESURF_ENABLE_DEFVAL -#undef SERDES_L3_TM_DIG_8_EYESURF_ENABLE_SHIFT -#undef SERDES_L3_TM_DIG_8_EYESURF_ENABLE_MASK -#define SERDES_L3_TM_DIG_8_EYESURF_ENABLE_DEFVAL 0x00000000 -#define SERDES_L3_TM_DIG_8_EYESURF_ENABLE_SHIFT 4 -#define SERDES_L3_TM_DIG_8_EYESURF_ENABLE_MASK 0x00000010U - -/*ILL calib counts BYPASSED with calcode bits*/ -#undef SERDES_L2_TM_MISC2_ILL_CAL_BYPASS_COUNTS_DEFVAL -#undef SERDES_L2_TM_MISC2_ILL_CAL_BYPASS_COUNTS_SHIFT -#undef SERDES_L2_TM_MISC2_ILL_CAL_BYPASS_COUNTS_MASK -#define SERDES_L2_TM_MISC2_ILL_CAL_BYPASS_COUNTS_DEFVAL 0x00000000 -#define SERDES_L2_TM_MISC2_ILL_CAL_BYPASS_COUNTS_SHIFT 7 -#define SERDES_L2_TM_MISC2_ILL_CAL_BYPASS_COUNTS_MASK 0x00000080U - -/*IQ ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , USB3 : SS*/ -#undef SERDES_L2_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_DEFVAL -#undef SERDES_L2_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_SHIFT -#undef SERDES_L2_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_MASK -#define SERDES_L2_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_DEFVAL 0x00000000 -#define SERDES_L2_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_SHIFT 0 -#define SERDES_L2_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_MASK 0x000000FFU - -/*IQ ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2*/ -#undef SERDES_L2_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_DEFVAL -#undef SERDES_L2_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_SHIFT -#undef SERDES_L2_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_MASK -#define SERDES_L2_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_DEFVAL 0x00000000 -#define SERDES_L2_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_SHIFT 0 -#define SERDES_L2_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_MASK 0x000000FFU - -/*G1A pll ctr bypass value*/ -#undef SERDES_L2_TM_ILL12_G1A_PLL_CTR_BYP_VAL_DEFVAL -#undef SERDES_L2_TM_ILL12_G1A_PLL_CTR_BYP_VAL_SHIFT -#undef SERDES_L2_TM_ILL12_G1A_PLL_CTR_BYP_VAL_MASK -#define SERDES_L2_TM_ILL12_G1A_PLL_CTR_BYP_VAL_DEFVAL 0x00000000 -#define SERDES_L2_TM_ILL12_G1A_PLL_CTR_BYP_VAL_SHIFT 0 -#define SERDES_L2_TM_ILL12_G1A_PLL_CTR_BYP_VAL_MASK 0x000000FFU - -/*E ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , USB3 : SS*/ -#undef SERDES_L2_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_DEFVAL -#undef SERDES_L2_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_SHIFT -#undef SERDES_L2_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_MASK -#define SERDES_L2_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_DEFVAL 0x00000000 -#define SERDES_L2_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_SHIFT 0 -#define SERDES_L2_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_MASK 0x000000FFU - -/*E ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2*/ -#undef SERDES_L2_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_DEFVAL -#undef SERDES_L2_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_SHIFT -#undef SERDES_L2_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_MASK -#define SERDES_L2_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_DEFVAL 0x00000000 -#define SERDES_L2_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_SHIFT 0 -#define SERDES_L2_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_MASK 0x000000FFU - -/*IQ ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3*/ -#undef SERDES_L2_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_DEFVAL -#undef SERDES_L2_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_SHIFT -#undef SERDES_L2_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_MASK -#define SERDES_L2_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_DEFVAL 0x00000000 -#define SERDES_L2_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_SHIFT 0 -#define SERDES_L2_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_MASK 0x000000FFU - -/*E ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3*/ -#undef SERDES_L2_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_DEFVAL -#undef SERDES_L2_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_SHIFT -#undef SERDES_L2_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_MASK -#define SERDES_L2_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_DEFVAL 0x00000000 -#define SERDES_L2_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_SHIFT 0 -#define SERDES_L2_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_MASK 0x000000FFU - -/*ILL calibration code change wait time*/ -#undef SERDES_L2_TM_ILL8_ILL_CAL_ITER_WAIT_DEFVAL -#undef SERDES_L2_TM_ILL8_ILL_CAL_ITER_WAIT_SHIFT -#undef SERDES_L2_TM_ILL8_ILL_CAL_ITER_WAIT_MASK -#define SERDES_L2_TM_ILL8_ILL_CAL_ITER_WAIT_DEFVAL 0x00000002 -#define SERDES_L2_TM_ILL8_ILL_CAL_ITER_WAIT_SHIFT 0 -#define SERDES_L2_TM_ILL8_ILL_CAL_ITER_WAIT_MASK 0x000000FFU - -/*IQ ILL polytrim bypass value*/ -#undef SERDES_L2_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_DEFVAL -#undef SERDES_L2_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_SHIFT -#undef SERDES_L2_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_MASK -#define SERDES_L2_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_DEFVAL 0x00000000 -#define SERDES_L2_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_SHIFT 0 -#define SERDES_L2_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_MASK 0x000000FFU - -/*bypass IQ polytrim*/ -#undef SERDES_L2_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_DEFVAL -#undef SERDES_L2_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_SHIFT -#undef SERDES_L2_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_MASK -#define SERDES_L2_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_DEFVAL 0x00000000 -#define SERDES_L2_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_SHIFT 0 -#define SERDES_L2_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_MASK 0x00000001U - -/*E ILL polytrim bypass value*/ -#undef SERDES_L2_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_DEFVAL -#undef SERDES_L2_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_SHIFT -#undef SERDES_L2_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_MASK -#define SERDES_L2_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_DEFVAL 0x00000000 -#define SERDES_L2_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_SHIFT 0 -#define SERDES_L2_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_MASK 0x000000FFU - -/*bypass E polytrim*/ -#undef SERDES_L2_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_DEFVAL -#undef SERDES_L2_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_SHIFT -#undef SERDES_L2_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_MASK -#define SERDES_L2_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_DEFVAL 0x00000000 -#define SERDES_L2_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_SHIFT 0 -#define SERDES_L2_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_MASK 0x00000001U - -/*ILL calib counts BYPASSED with calcode bits*/ -#undef SERDES_L3_TM_MISC2_ILL_CAL_BYPASS_COUNTS_DEFVAL -#undef SERDES_L3_TM_MISC2_ILL_CAL_BYPASS_COUNTS_SHIFT -#undef SERDES_L3_TM_MISC2_ILL_CAL_BYPASS_COUNTS_MASK -#define SERDES_L3_TM_MISC2_ILL_CAL_BYPASS_COUNTS_DEFVAL 0x00000000 -#define SERDES_L3_TM_MISC2_ILL_CAL_BYPASS_COUNTS_SHIFT 7 -#define SERDES_L3_TM_MISC2_ILL_CAL_BYPASS_COUNTS_MASK 0x00000080U - -/*IQ ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , USB3 : SS*/ -#undef SERDES_L3_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_DEFVAL -#undef SERDES_L3_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_SHIFT -#undef SERDES_L3_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_MASK -#define SERDES_L3_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_DEFVAL 0x00000000 -#define SERDES_L3_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_SHIFT 0 -#define SERDES_L3_TM_IQ_ILL1_ILL_BYPASS_IQ_CALCODE_F0_MASK 0x000000FFU - -/*IQ ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2*/ -#undef SERDES_L3_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_DEFVAL -#undef SERDES_L3_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_SHIFT -#undef SERDES_L3_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_MASK -#define SERDES_L3_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_DEFVAL 0x00000000 -#define SERDES_L3_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_SHIFT 0 -#define SERDES_L3_TM_IQ_ILL2_ILL_BYPASS_IQ_CALCODE_F1_MASK 0x000000FFU - -/*G1A pll ctr bypass value*/ -#undef SERDES_L3_TM_ILL12_G1A_PLL_CTR_BYP_VAL_DEFVAL -#undef SERDES_L3_TM_ILL12_G1A_PLL_CTR_BYP_VAL_SHIFT -#undef SERDES_L3_TM_ILL12_G1A_PLL_CTR_BYP_VAL_MASK -#define SERDES_L3_TM_ILL12_G1A_PLL_CTR_BYP_VAL_DEFVAL 0x00000000 -#define SERDES_L3_TM_ILL12_G1A_PLL_CTR_BYP_VAL_SHIFT 0 -#define SERDES_L3_TM_ILL12_G1A_PLL_CTR_BYP_VAL_MASK 0x000000FFU - -/*E ILL F0 CALCODE bypass value. MPHY : G1a, PCIE : Gen 1, SATA : Gen1 , USB3 : SS*/ -#undef SERDES_L3_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_DEFVAL -#undef SERDES_L3_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_SHIFT -#undef SERDES_L3_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_MASK -#define SERDES_L3_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_DEFVAL 0x00000000 -#define SERDES_L3_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_SHIFT 0 -#define SERDES_L3_TM_E_ILL1_ILL_BYPASS_E_CALCODE_F0_MASK 0x000000FFU - -/*E ILL F1 CALCODE bypass value. MPHY : G1b, PCIE : Gen2, SATA: Gen2*/ -#undef SERDES_L3_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_DEFVAL -#undef SERDES_L3_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_SHIFT -#undef SERDES_L3_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_MASK -#define SERDES_L3_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_DEFVAL 0x00000000 -#define SERDES_L3_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_SHIFT 0 -#define SERDES_L3_TM_E_ILL2_ILL_BYPASS_E_CALCODE_F1_MASK 0x000000FFU - -/*G2A_PCIe1 PLL ctr bypass value*/ -#undef SERDES_L3_TM_ILL11_G2A_PCIEG1_PLL_CTR_11_8_BYP_VAL_DEFVAL -#undef SERDES_L3_TM_ILL11_G2A_PCIEG1_PLL_CTR_11_8_BYP_VAL_SHIFT -#undef SERDES_L3_TM_ILL11_G2A_PCIEG1_PLL_CTR_11_8_BYP_VAL_MASK -#define SERDES_L3_TM_ILL11_G2A_PCIEG1_PLL_CTR_11_8_BYP_VAL_DEFVAL 0x00000000 -#define SERDES_L3_TM_ILL11_G2A_PCIEG1_PLL_CTR_11_8_BYP_VAL_SHIFT 4 -#define SERDES_L3_TM_ILL11_G2A_PCIEG1_PLL_CTR_11_8_BYP_VAL_MASK 0x000000F0U - -/*IQ ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3*/ -#undef SERDES_L3_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_DEFVAL -#undef SERDES_L3_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_SHIFT -#undef SERDES_L3_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_MASK -#define SERDES_L3_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_DEFVAL 0x00000000 -#define SERDES_L3_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_SHIFT 0 -#define SERDES_L3_TM_IQ_ILL3_ILL_BYPASS_IQ_CALCODE_F2_MASK 0x000000FFU - -/*E ILL F2CALCODE bypass value. MPHY : G2a, SATA : Gen3*/ -#undef SERDES_L3_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_DEFVAL -#undef SERDES_L3_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_SHIFT -#undef SERDES_L3_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_MASK -#define SERDES_L3_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_DEFVAL 0x00000000 -#define SERDES_L3_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_SHIFT 0 -#define SERDES_L3_TM_E_ILL3_ILL_BYPASS_E_CALCODE_F2_MASK 0x000000FFU - -/*ILL calibration code change wait time*/ -#undef SERDES_L3_TM_ILL8_ILL_CAL_ITER_WAIT_DEFVAL -#undef SERDES_L3_TM_ILL8_ILL_CAL_ITER_WAIT_SHIFT -#undef SERDES_L3_TM_ILL8_ILL_CAL_ITER_WAIT_MASK -#define SERDES_L3_TM_ILL8_ILL_CAL_ITER_WAIT_DEFVAL 0x00000002 -#define SERDES_L3_TM_ILL8_ILL_CAL_ITER_WAIT_SHIFT 0 -#define SERDES_L3_TM_ILL8_ILL_CAL_ITER_WAIT_MASK 0x000000FFU - -/*IQ ILL polytrim bypass value*/ -#undef SERDES_L3_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_DEFVAL -#undef SERDES_L3_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_SHIFT -#undef SERDES_L3_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_MASK -#define SERDES_L3_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_DEFVAL 0x00000000 -#define SERDES_L3_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_SHIFT 0 -#define SERDES_L3_TM_IQ_ILL8_ILL_BYPASS_IQ_POLYTRIM_VAL_MASK 0x000000FFU - -/*bypass IQ polytrim*/ -#undef SERDES_L3_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_DEFVAL -#undef SERDES_L3_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_SHIFT -#undef SERDES_L3_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_MASK -#define SERDES_L3_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_DEFVAL 0x00000000 -#define SERDES_L3_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_SHIFT 0 -#define SERDES_L3_TM_IQ_ILL9_ILL_BYPASS_IQ_POLYTIM_MASK 0x00000001U - -/*E ILL polytrim bypass value*/ -#undef SERDES_L3_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_DEFVAL -#undef SERDES_L3_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_SHIFT -#undef SERDES_L3_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_MASK -#define SERDES_L3_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_DEFVAL 0x00000000 -#define SERDES_L3_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_SHIFT 0 -#define SERDES_L3_TM_E_ILL8_ILL_BYPASS_E_POLYTRIM_VAL_MASK 0x000000FFU - -/*bypass E polytrim*/ -#undef SERDES_L3_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_DEFVAL -#undef SERDES_L3_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_SHIFT -#undef SERDES_L3_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_MASK -#define SERDES_L3_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_DEFVAL 0x00000000 -#define SERDES_L3_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_SHIFT 0 -#define SERDES_L3_TM_E_ILL9_ILL_BYPASS_E_POLYTIM_MASK 0x00000001U - -/*Delay apb reset by specified amount*/ -#undef SERDES_L0_TM_RST_DLY_APB_RST_DLY_DEFVAL -#undef SERDES_L0_TM_RST_DLY_APB_RST_DLY_SHIFT -#undef SERDES_L0_TM_RST_DLY_APB_RST_DLY_MASK -#define SERDES_L0_TM_RST_DLY_APB_RST_DLY_DEFVAL 0x00000000 -#define SERDES_L0_TM_RST_DLY_APB_RST_DLY_SHIFT 0 -#define SERDES_L0_TM_RST_DLY_APB_RST_DLY_MASK 0x000000FFU - -/*Enable Bypass for <7> of TM_ANA_BYPS_15*/ -#undef SERDES_L0_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_DEFVAL -#undef SERDES_L0_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT -#undef SERDES_L0_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK -#define SERDES_L0_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_DEFVAL 0x00000000 -#define SERDES_L0_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT 6 -#define SERDES_L0_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK 0x00000040U - -/*Enable Bypass for <7> of TM_ANA_BYPS_12*/ -#undef SERDES_L0_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_DEFVAL -#undef SERDES_L0_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT -#undef SERDES_L0_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK -#define SERDES_L0_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_DEFVAL 0x00000000 -#define SERDES_L0_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT 6 -#define SERDES_L0_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK 0x00000040U - -/*Delay apb reset by specified amount*/ -#undef SERDES_L1_TM_RST_DLY_APB_RST_DLY_DEFVAL -#undef SERDES_L1_TM_RST_DLY_APB_RST_DLY_SHIFT -#undef SERDES_L1_TM_RST_DLY_APB_RST_DLY_MASK -#define SERDES_L1_TM_RST_DLY_APB_RST_DLY_DEFVAL 0x00000000 -#define SERDES_L1_TM_RST_DLY_APB_RST_DLY_SHIFT 0 -#define SERDES_L1_TM_RST_DLY_APB_RST_DLY_MASK 0x000000FFU - -/*Enable Bypass for <7> of TM_ANA_BYPS_15*/ -#undef SERDES_L1_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_DEFVAL -#undef SERDES_L1_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT -#undef SERDES_L1_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK -#define SERDES_L1_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_DEFVAL 0x00000000 -#define SERDES_L1_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT 6 -#define SERDES_L1_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK 0x00000040U - -/*Enable Bypass for <7> of TM_ANA_BYPS_12*/ -#undef SERDES_L1_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_DEFVAL -#undef SERDES_L1_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT -#undef SERDES_L1_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK -#define SERDES_L1_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_DEFVAL 0x00000000 -#define SERDES_L1_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT 6 -#define SERDES_L1_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK 0x00000040U - -/*Delay apb reset by specified amount*/ -#undef SERDES_L2_TM_RST_DLY_APB_RST_DLY_DEFVAL -#undef SERDES_L2_TM_RST_DLY_APB_RST_DLY_SHIFT -#undef SERDES_L2_TM_RST_DLY_APB_RST_DLY_MASK -#define SERDES_L2_TM_RST_DLY_APB_RST_DLY_DEFVAL 0x00000000 -#define SERDES_L2_TM_RST_DLY_APB_RST_DLY_SHIFT 0 -#define SERDES_L2_TM_RST_DLY_APB_RST_DLY_MASK 0x000000FFU - -/*Enable Bypass for <7> of TM_ANA_BYPS_15*/ -#undef SERDES_L2_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_DEFVAL -#undef SERDES_L2_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT -#undef SERDES_L2_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK -#define SERDES_L2_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_DEFVAL 0x00000000 -#define SERDES_L2_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT 6 -#define SERDES_L2_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK 0x00000040U - -/*Enable Bypass for <7> of TM_ANA_BYPS_12*/ -#undef SERDES_L2_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_DEFVAL -#undef SERDES_L2_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT -#undef SERDES_L2_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK -#define SERDES_L2_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_DEFVAL 0x00000000 -#define SERDES_L2_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT 6 -#define SERDES_L2_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK 0x00000040U - -/*Delay apb reset by specified amount*/ -#undef SERDES_L3_TM_RST_DLY_APB_RST_DLY_DEFVAL -#undef SERDES_L3_TM_RST_DLY_APB_RST_DLY_SHIFT -#undef SERDES_L3_TM_RST_DLY_APB_RST_DLY_MASK -#define SERDES_L3_TM_RST_DLY_APB_RST_DLY_DEFVAL 0x00000000 -#define SERDES_L3_TM_RST_DLY_APB_RST_DLY_SHIFT 0 -#define SERDES_L3_TM_RST_DLY_APB_RST_DLY_MASK 0x000000FFU - -/*Enable Bypass for <7> of TM_ANA_BYPS_15*/ -#undef SERDES_L3_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_DEFVAL -#undef SERDES_L3_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT -#undef SERDES_L3_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK -#define SERDES_L3_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_DEFVAL 0x00000000 -#define SERDES_L3_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_SHIFT 6 -#define SERDES_L3_TM_ANA_BYP_15_FORCE_UPHY_ENABLE_LOW_LEAKAGE_MASK 0x00000040U - -/*Enable Bypass for <7> of TM_ANA_BYPS_12*/ -#undef SERDES_L3_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_DEFVAL -#undef SERDES_L3_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT -#undef SERDES_L3_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK -#define SERDES_L3_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_DEFVAL 0x00000000 -#define SERDES_L3_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_SHIFT 6 -#define SERDES_L3_TM_ANA_BYP_12_FORCE_UPHY_PSO_HSRXDIG_MASK 0x00000040U - -/*Controls UPHY Lane 0 protocol configuration. 0 - PowerDown, 1 - PCIe .0, 2 - Sata0, 3 - USB0, 4 - DP.1, 5 - SGMII0, 6 - Unuse - , 7 - Unused*/ -#undef SERDES_ICM_CFG0_L0_ICM_CFG_DEFVAL -#undef SERDES_ICM_CFG0_L0_ICM_CFG_SHIFT -#undef SERDES_ICM_CFG0_L0_ICM_CFG_MASK -#define SERDES_ICM_CFG0_L0_ICM_CFG_DEFVAL 0x00000000 -#define SERDES_ICM_CFG0_L0_ICM_CFG_SHIFT 0 -#define SERDES_ICM_CFG0_L0_ICM_CFG_MASK 0x00000007U - -/*Controls UPHY Lane 1 protocol configuration. 0 - PowerDown, 1 - PCIe.1, 2 - Sata1, 3 - USB0, 4 - DP.0, 5 - SGMII1, 6 - Unused - 7 - Unused*/ -#undef SERDES_ICM_CFG0_L1_ICM_CFG_DEFVAL -#undef SERDES_ICM_CFG0_L1_ICM_CFG_SHIFT -#undef SERDES_ICM_CFG0_L1_ICM_CFG_MASK -#define SERDES_ICM_CFG0_L1_ICM_CFG_DEFVAL 0x00000000 -#define SERDES_ICM_CFG0_L1_ICM_CFG_SHIFT 4 -#define SERDES_ICM_CFG0_L1_ICM_CFG_MASK 0x00000070U - -/*Controls UPHY Lane 2 protocol configuration. 0 - PowerDown, 1 - PCIe.1, 2 - Sata0, 3 - USB0, 4 - DP.1, 5 - SGMII2, 6 - Unused - 7 - Unused*/ -#undef SERDES_ICM_CFG1_L2_ICM_CFG_DEFVAL -#undef SERDES_ICM_CFG1_L2_ICM_CFG_SHIFT -#undef SERDES_ICM_CFG1_L2_ICM_CFG_MASK -#define SERDES_ICM_CFG1_L2_ICM_CFG_DEFVAL 0x00000000 -#define SERDES_ICM_CFG1_L2_ICM_CFG_SHIFT 0 -#define SERDES_ICM_CFG1_L2_ICM_CFG_MASK 0x00000007U - -/*Controls UPHY Lane 3 protocol configuration. 0 - PowerDown, 1 - PCIe.3, 2 - Sata1, 3 - USB1, 4 - DP.0, 5 - SGMII3, 6 - Unused - 7 - Unused*/ -#undef SERDES_ICM_CFG1_L3_ICM_CFG_DEFVAL -#undef SERDES_ICM_CFG1_L3_ICM_CFG_SHIFT -#undef SERDES_ICM_CFG1_L3_ICM_CFG_MASK -#define SERDES_ICM_CFG1_L3_ICM_CFG_DEFVAL 0x00000000 -#define SERDES_ICM_CFG1_L3_ICM_CFG_SHIFT 4 -#define SERDES_ICM_CFG1_L3_ICM_CFG_MASK 0x00000070U - -/*Enable/disable DP post2 path*/ -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_DEFVAL -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_SHIFT -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_MASK -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_DEFVAL 0x00000000 -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_SHIFT 5 -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_MASK 0x00000020U - -/*Override enable/disable of DP post2 path*/ -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_DEFVAL -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_SHIFT -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_MASK -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_DEFVAL 0x00000000 -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_SHIFT 4 -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_MASK 0x00000010U - -/*Override enable/disable of DP post1 path*/ -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_DEFVAL -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_SHIFT -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_MASK -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_DEFVAL 0x00000000 -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_SHIFT 2 -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_MASK 0x00000004U - -/*Enable/disable DP main path*/ -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_DEFVAL -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_SHIFT -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_MASK -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_DEFVAL 0x00000000 -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_SHIFT 1 -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_MASK 0x00000002U - -/*Override enable/disable of DP main path*/ -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_DEFVAL -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_SHIFT -#undef SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_MASK -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_DEFVAL 0x00000000 -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_SHIFT 0 -#define SERDES_L0_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_MASK 0x00000001U - -/*Enable/disable DP post2 path*/ -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_DEFVAL -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_SHIFT -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_MASK -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_DEFVAL 0x00000000 -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_SHIFT 5 -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_POST2_PATH_MASK 0x00000020U - -/*Override enable/disable of DP post2 path*/ -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_DEFVAL -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_SHIFT -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_MASK -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_DEFVAL 0x00000000 -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_SHIFT 4 -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST2_PATH_MASK 0x00000010U - -/*Override enable/disable of DP post1 path*/ -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_DEFVAL -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_SHIFT -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_MASK -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_DEFVAL 0x00000000 -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_SHIFT 2 -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_POST1_PATH_MASK 0x00000004U - -/*Enable/disable DP main path*/ -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_DEFVAL -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_SHIFT -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_MASK -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_DEFVAL 0x00000000 -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_SHIFT 1 -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_DP_ENABLE_MAIN_PATH_MASK 0x00000002U - -/*Override enable/disable of DP main path*/ -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_DEFVAL -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_SHIFT -#undef SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_MASK -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_DEFVAL 0x00000000 -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_SHIFT 0 -#define SERDES_L1_TXPMD_TM_45_DP_TM_TX_OVRD_DP_ENABLE_MAIN_PATH_MASK 0x00000001U - -/*Test register force for enabling/disablign TX deemphasis bits <17:0>*/ -#undef SERDES_L0_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_DEFVAL -#undef SERDES_L0_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_SHIFT -#undef SERDES_L0_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_MASK -#define SERDES_L0_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_DEFVAL 0x00000000 -#define SERDES_L0_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_SHIFT 0 -#define SERDES_L0_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_MASK 0x00000001U - -/*Test register force for enabling/disablign TX deemphasis bits <17:0>*/ -#undef SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_DEFVAL -#undef SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_SHIFT -#undef SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_MASK -#define SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_DEFVAL 0x00000000 -#define SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_SHIFT 0 -#define SERDES_L1_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_MASK 0x00000001U - -/*Test register force for enabling/disablign TX deemphasis bits <17:0>*/ -#undef SERDES_L3_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_DEFVAL -#undef SERDES_L3_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_SHIFT -#undef SERDES_L3_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_MASK -#define SERDES_L3_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_DEFVAL 0x00000000 -#define SERDES_L3_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_SHIFT 0 -#define SERDES_L3_TX_ANA_TM_118_FORCE_TX_DEEMPH_17_0_MASK 0x00000001U - -/*FPHL FSM accumulate cycles*/ -#undef SERDES_L3_TM_CDR5_FPHL_FSM_ACC_CYCLES_DEFVAL -#undef SERDES_L3_TM_CDR5_FPHL_FSM_ACC_CYCLES_SHIFT -#undef SERDES_L3_TM_CDR5_FPHL_FSM_ACC_CYCLES_MASK -#define SERDES_L3_TM_CDR5_FPHL_FSM_ACC_CYCLES_DEFVAL 0x00000000 -#define SERDES_L3_TM_CDR5_FPHL_FSM_ACC_CYCLES_SHIFT 5 -#define SERDES_L3_TM_CDR5_FPHL_FSM_ACC_CYCLES_MASK 0x000000E0U - -/*FFL Phase0 int gain aka 2ol SD update rate*/ -#undef SERDES_L3_TM_CDR5_FFL_PH0_INT_GAIN_DEFVAL -#undef SERDES_L3_TM_CDR5_FFL_PH0_INT_GAIN_SHIFT -#undef SERDES_L3_TM_CDR5_FFL_PH0_INT_GAIN_MASK -#define SERDES_L3_TM_CDR5_FFL_PH0_INT_GAIN_DEFVAL 0x00000000 -#define SERDES_L3_TM_CDR5_FFL_PH0_INT_GAIN_SHIFT 0 -#define SERDES_L3_TM_CDR5_FFL_PH0_INT_GAIN_MASK 0x0000001FU - -/*FFL Phase0 prop gain aka 1ol SD update rate*/ -#undef SERDES_L3_TM_CDR16_FFL_PH0_PROP_GAIN_DEFVAL -#undef SERDES_L3_TM_CDR16_FFL_PH0_PROP_GAIN_SHIFT -#undef SERDES_L3_TM_CDR16_FFL_PH0_PROP_GAIN_MASK -#define SERDES_L3_TM_CDR16_FFL_PH0_PROP_GAIN_DEFVAL 0x00000000 -#define SERDES_L3_TM_CDR16_FFL_PH0_PROP_GAIN_SHIFT 0 -#define SERDES_L3_TM_CDR16_FFL_PH0_PROP_GAIN_MASK 0x0000001FU - -/*EQ stg 2 controls BYPASSED*/ -#undef SERDES_L3_TM_EQ0_EQ_STG2_CTRL_BYP_DEFVAL -#undef SERDES_L3_TM_EQ0_EQ_STG2_CTRL_BYP_SHIFT -#undef SERDES_L3_TM_EQ0_EQ_STG2_CTRL_BYP_MASK -#define SERDES_L3_TM_EQ0_EQ_STG2_CTRL_BYP_DEFVAL 0x00000000 -#define SERDES_L3_TM_EQ0_EQ_STG2_CTRL_BYP_SHIFT 5 -#define SERDES_L3_TM_EQ0_EQ_STG2_CTRL_BYP_MASK 0x00000020U - -/*EQ STG2 RL PROG*/ -#undef SERDES_L3_TM_EQ1_EQ_STG2_RL_PROG_DEFVAL -#undef SERDES_L3_TM_EQ1_EQ_STG2_RL_PROG_SHIFT -#undef SERDES_L3_TM_EQ1_EQ_STG2_RL_PROG_MASK -#define SERDES_L3_TM_EQ1_EQ_STG2_RL_PROG_DEFVAL 0x00000000 -#define SERDES_L3_TM_EQ1_EQ_STG2_RL_PROG_SHIFT 0 -#define SERDES_L3_TM_EQ1_EQ_STG2_RL_PROG_MASK 0x00000003U - -/*EQ stg 2 preamp mode val*/ -#undef SERDES_L3_TM_EQ1_EQ_STG2_PREAMP_MODE_VAL_DEFVAL -#undef SERDES_L3_TM_EQ1_EQ_STG2_PREAMP_MODE_VAL_SHIFT -#undef SERDES_L3_TM_EQ1_EQ_STG2_PREAMP_MODE_VAL_MASK -#define SERDES_L3_TM_EQ1_EQ_STG2_PREAMP_MODE_VAL_DEFVAL 0x00000000 -#define SERDES_L3_TM_EQ1_EQ_STG2_PREAMP_MODE_VAL_SHIFT 2 -#define SERDES_L3_TM_EQ1_EQ_STG2_PREAMP_MODE_VAL_MASK 0x00000004U - -/*Margining factor value*/ -#undef SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_DEFVAL -#undef SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_SHIFT -#undef SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_MASK -#define SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_DEFVAL 0x00000000 -#define SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_SHIFT 0 -#define SERDES_L1_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_MASK 0x0000001FU - -/*Margining factor value*/ -#undef SERDES_L0_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_DEFVAL -#undef SERDES_L0_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_SHIFT -#undef SERDES_L0_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_MASK -#define SERDES_L0_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_DEFVAL 0x00000000 -#define SERDES_L0_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_SHIFT 0 -#define SERDES_L0_TXPMD_TM_48_TM_RESULTANT_MARGINING_FACTOR_MASK 0x0000001FU - -/*pipe_TX_Deemph. 0: -6dB de-emphasis, 1: -3.5dB de-emphasis, 2 : No de-emphasis, Others: reserved*/ -#undef SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_DEFVAL -#undef SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_SHIFT -#undef SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_MASK -#define SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_DEFVAL 0x00000002 -#define SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_SHIFT 0 -#define SERDES_L1_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_MASK 0x000000FFU - -/*pipe_TX_Deemph. 0: -6dB de-emphasis, 1: -3.5dB de-emphasis, 2 : No de-emphasis, Others: reserved*/ -#undef SERDES_L0_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_DEFVAL -#undef SERDES_L0_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_SHIFT -#undef SERDES_L0_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_MASK -#define SERDES_L0_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_DEFVAL 0x00000002 -#define SERDES_L0_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_SHIFT 0 -#define SERDES_L0_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_MASK 0x000000FFU - -/*pipe_TX_Deemph. 0: -6dB de-emphasis, 1: -3.5dB de-emphasis, 2 : No de-emphasis, Others: reserved*/ -#undef SERDES_L3_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_DEFVAL -#undef SERDES_L3_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_SHIFT -#undef SERDES_L3_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_MASK -#define SERDES_L3_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_DEFVAL 0x00000002 -#define SERDES_L3_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_SHIFT 0 -#define SERDES_L3_TX_ANA_TM_18_PIPE_TX_DEEMPH_7_0_MASK 0x000000FFU -#undef CRL_APB_RST_LPD_TOP_OFFSET -#define CRL_APB_RST_LPD_TOP_OFFSET 0XFF5E023C -#undef USB3_0_FPD_POWER_PRSNT_OFFSET -#define USB3_0_FPD_POWER_PRSNT_OFFSET 0XFF9D0080 -#undef USB3_0_FPD_PIPE_CLK_OFFSET -#define USB3_0_FPD_PIPE_CLK_OFFSET 0XFF9D007C -#undef CRL_APB_RST_LPD_TOP_OFFSET -#define CRL_APB_RST_LPD_TOP_OFFSET 0XFF5E023C -#undef CRL_APB_RST_LPD_IOU0_OFFSET -#define CRL_APB_RST_LPD_IOU0_OFFSET 0XFF5E0230 -#undef SIOU_SATA_MISC_CTRL_OFFSET -#define SIOU_SATA_MISC_CTRL_OFFSET 0XFD3D0100 -#undef CRF_APB_RST_FPD_TOP_OFFSET -#define CRF_APB_RST_FPD_TOP_OFFSET 0XFD1A0100 -#undef CRF_APB_RST_FPD_TOP_OFFSET -#define CRF_APB_RST_FPD_TOP_OFFSET 0XFD1A0100 -#undef DP_DP_PHY_RESET_OFFSET -#define DP_DP_PHY_RESET_OFFSET 0XFD4A0200 -#undef DP_DP_TX_PHY_POWER_DOWN_OFFSET -#define DP_DP_TX_PHY_POWER_DOWN_OFFSET 0XFD4A0238 -#undef USB3_0_XHCI_GUSB2PHYCFG_OFFSET -#define USB3_0_XHCI_GUSB2PHYCFG_OFFSET 0XFE20C200 -#undef USB3_0_XHCI_GFLADJ_OFFSET -#define USB3_0_XHCI_GFLADJ_OFFSET 0XFE20C630 -#undef PCIE_ATTRIB_ATTR_25_OFFSET -#define PCIE_ATTRIB_ATTR_25_OFFSET 0XFD480064 -#undef SATA_AHCI_VENDOR_PP2C_OFFSET -#define SATA_AHCI_VENDOR_PP2C_OFFSET 0XFD0C00AC -#undef SATA_AHCI_VENDOR_PP3C_OFFSET -#define SATA_AHCI_VENDOR_PP3C_OFFSET 0XFD0C00B0 -#undef SATA_AHCI_VENDOR_PP4C_OFFSET -#define SATA_AHCI_VENDOR_PP4C_OFFSET 0XFD0C00B4 -#undef SATA_AHCI_VENDOR_PP5C_OFFSET -#define SATA_AHCI_VENDOR_PP5C_OFFSET 0XFD0C00B8 - -/*USB 0 reset for control registers*/ -#undef CRL_APB_RST_LPD_TOP_USB0_APB_RESET_DEFVAL -#undef CRL_APB_RST_LPD_TOP_USB0_APB_RESET_SHIFT -#undef CRL_APB_RST_LPD_TOP_USB0_APB_RESET_MASK -#define CRL_APB_RST_LPD_TOP_USB0_APB_RESET_DEFVAL 0x00188FDF -#define CRL_APB_RST_LPD_TOP_USB0_APB_RESET_SHIFT 10 -#define CRL_APB_RST_LPD_TOP_USB0_APB_RESET_MASK 0x00000400U - -/*This bit is used to choose between PIPE power present and 1'b1*/ -#undef USB3_0_FPD_POWER_PRSNT_OPTION_DEFVAL -#undef USB3_0_FPD_POWER_PRSNT_OPTION_SHIFT -#undef USB3_0_FPD_POWER_PRSNT_OPTION_MASK -#define USB3_0_FPD_POWER_PRSNT_OPTION_DEFVAL -#define USB3_0_FPD_POWER_PRSNT_OPTION_SHIFT 0 -#define USB3_0_FPD_POWER_PRSNT_OPTION_MASK 0x00000001U - -/*This bit is used to choose between PIPE clock coming from SerDes and the suspend clk*/ -#undef USB3_0_FPD_PIPE_CLK_OPTION_DEFVAL -#undef USB3_0_FPD_PIPE_CLK_OPTION_SHIFT -#undef USB3_0_FPD_PIPE_CLK_OPTION_MASK -#define USB3_0_FPD_PIPE_CLK_OPTION_DEFVAL -#define USB3_0_FPD_PIPE_CLK_OPTION_SHIFT 0 -#define USB3_0_FPD_PIPE_CLK_OPTION_MASK 0x00000001U - -/*USB 0 sleep circuit reset*/ -#undef CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_DEFVAL -#undef CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_SHIFT -#undef CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_MASK -#define CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_DEFVAL 0x00188FDF -#define CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_SHIFT 8 -#define CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_MASK 0x00000100U - -/*USB 0 reset*/ -#undef CRL_APB_RST_LPD_TOP_USB0_CORERESET_DEFVAL -#undef CRL_APB_RST_LPD_TOP_USB0_CORERESET_SHIFT -#undef CRL_APB_RST_LPD_TOP_USB0_CORERESET_MASK -#define CRL_APB_RST_LPD_TOP_USB0_CORERESET_DEFVAL 0x00188FDF -#define CRL_APB_RST_LPD_TOP_USB0_CORERESET_SHIFT 6 -#define CRL_APB_RST_LPD_TOP_USB0_CORERESET_MASK 0x00000040U - -/*GEM 3 reset*/ -#undef CRL_APB_RST_LPD_IOU0_GEM3_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU0_GEM3_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU0_GEM3_RESET_MASK -#define CRL_APB_RST_LPD_IOU0_GEM3_RESET_DEFVAL 0x0000000F -#define CRL_APB_RST_LPD_IOU0_GEM3_RESET_SHIFT 3 -#define CRL_APB_RST_LPD_IOU0_GEM3_RESET_MASK 0x00000008U - -/*Sata PM clock control select*/ -#undef SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL_DEFVAL -#undef SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL_SHIFT -#undef SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL_MASK -#define SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL_DEFVAL -#define SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL_SHIFT 0 -#define SIOU_SATA_MISC_CTRL_SATA_PM_CLK_SEL_MASK 0x00000003U - -/*Sata block level reset*/ -#undef CRF_APB_RST_FPD_TOP_SATA_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_SATA_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_SATA_RESET_MASK -#define CRF_APB_RST_FPD_TOP_SATA_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_SATA_RESET_SHIFT 1 -#define CRF_APB_RST_FPD_TOP_SATA_RESET_MASK 0x00000002U - -/*Display Port block level reset (includes DPDMA)*/ -#undef CRF_APB_RST_FPD_TOP_DP_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_DP_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_DP_RESET_MASK -#define CRF_APB_RST_FPD_TOP_DP_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_DP_RESET_SHIFT 16 -#define CRF_APB_RST_FPD_TOP_DP_RESET_MASK 0x00010000U - -/*Set to '1' to hold the GT in reset. Clear to release.*/ -#undef DP_DP_PHY_RESET_GT_RESET_DEFVAL -#undef DP_DP_PHY_RESET_GT_RESET_SHIFT -#undef DP_DP_PHY_RESET_GT_RESET_MASK -#define DP_DP_PHY_RESET_GT_RESET_DEFVAL 0x00010003 -#define DP_DP_PHY_RESET_GT_RESET_SHIFT 1 -#define DP_DP_PHY_RESET_GT_RESET_MASK 0x00000002U - -/*Two bits per lane. When set to 11, moves the GT to power down mode. When set to 00, GT will be in active state. bits [1:0] - - ane0 Bits [3:2] - lane 1*/ -#undef DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_DEFVAL -#undef DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_SHIFT -#undef DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_MASK -#define DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_DEFVAL 0x00000000 -#define DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_SHIFT 0 -#define DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_MASK 0x0000000FU - -/*USB 2.0 Turnaround Time (USBTrdTim) Sets the turnaround time in PHY clocks. Specifies the response time for a MAC request to - he Packet FIFO Controller (PFC) to fetch data from the DFIFO (SPRAM). The following are the required values for the minimum S - C bus frequency of 60 MHz. USB turnaround time is a critical certification criteria when using long cables and five hub level - . The required values for this field: - 4'h5: When the MAC interface is 16-bit UTMI+. - 4'h9: When the MAC interface is 8-bit - UTMI+/ULPI. If SoC bus clock is less than 60 MHz, and USB turnaround time is not critical, this field can be set to a larger - alue. Note: This field is valid only in device mode.*/ -#undef USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM_DEFVAL -#undef USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM_SHIFT -#undef USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM_MASK -#define USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM_DEFVAL 0x00000000 -#define USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM_SHIFT 10 -#define USB3_0_XHCI_GUSB2PHYCFG_USBTRDTIM_MASK 0x00003C00U - -/*Transceiver Delay: Enables a delay between the assertion of the UTMI/ULPI Transceiver Select signal (for HS) and the assertio - of the TxValid signal during a HS Chirp. When this bit is set to 1, a delay (of approximately 2.5 us) is introduced from the - time when the Transceiver Select is set to 2'b00 (HS) to the time the TxValid is driven to 0 for sending the chirp-K. This de - ay is required for some UTMI/ULPI PHYs. Note: - If you enable the hibernation feature when the device core comes out of power - off, you must re-initialize this bit with the appropriate value because the core does not save and restore this bit value dur - ng hibernation. - This bit is valid only in device mode.*/ -#undef USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY_DEFVAL -#undef USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY_SHIFT -#undef USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY_MASK -#define USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY_DEFVAL 0x00000000 -#define USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY_SHIFT 9 -#define USB3_0_XHCI_GUSB2PHYCFG_XCVRDLY_MASK 0x00000200U - -/*Enable utmi_sleep_n and utmi_l1_suspend_n (EnblSlpM) The application uses this bit to control utmi_sleep_n and utmi_l1_suspen - _n assertion to the PHY in the L1 state. - 1'b0: utmi_sleep_n and utmi_l1_suspend_n assertion from the core is not transferre - to the external PHY. - 1'b1: utmi_sleep_n and utmi_l1_suspend_n assertion from the core is transferred to the external PHY. - ote: This bit must be set high for Port0 if PHY is used. Note: In Device mode - Before issuing any device endpoint command wh - n operating in 2.0 speeds, disable this bit and enable it after the command completes. Without disabling this bit, if a comma - d is issued when the device is in L1 state and if mac2_clk (utmi_clk/ulpi_clk) is gated off, the command will not get complet - d.*/ -#undef USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM_DEFVAL -#undef USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM_SHIFT -#undef USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM_MASK -#define USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM_DEFVAL 0x00000000 -#define USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM_SHIFT 8 -#define USB3_0_XHCI_GUSB2PHYCFG_ENBLSLPM_MASK 0x00000100U - -/*USB 2.0 High-Speed PHY or USB 1.1 Full-Speed Serial Transceiver Select The application uses this bit to select a high-speed P - Y or a full-speed transceiver. - 1'b0: USB 2.0 high-speed UTMI+ or ULPI PHY. This bit is always 0, with Write Only access. - - 'b1: USB 1.1 full-speed serial transceiver. This bit is always 1, with Write Only access. If both interface types are selecte - in coreConsultant (that is, parameters' values are not zero), the application uses this bit to select the active interface i - active, with Read-Write bit access. Note: USB 1.1 full-serial transceiver is not supported. This bit always reads as 1'b0.*/ -#undef USB3_0_XHCI_GUSB2PHYCFG_PHYSEL_DEFVAL -#undef USB3_0_XHCI_GUSB2PHYCFG_PHYSEL_SHIFT -#undef USB3_0_XHCI_GUSB2PHYCFG_PHYSEL_MASK -#define USB3_0_XHCI_GUSB2PHYCFG_PHYSEL_DEFVAL 0x00000000 -#define USB3_0_XHCI_GUSB2PHYCFG_PHYSEL_SHIFT 7 -#define USB3_0_XHCI_GUSB2PHYCFG_PHYSEL_MASK 0x00000080U - -/*Full-Speed Serial Interface Select (FSIntf) The application uses this bit to select a unidirectional or bidirectional USB 1.1 - full-speed serial transceiver interface. - 1'b0: 6-pin unidirectional full-speed serial interface. This bit is set to 0 with - ead Only access. - 1'b1: 3-pin bidirectional full-speed serial interface. This bit is set to 0 with Read Only access. Note: U - B 1.1 full-speed serial interface is not supported. This bit always reads as 1'b0.*/ -#undef USB3_0_XHCI_GUSB2PHYCFG_FSINTF_DEFVAL -#undef USB3_0_XHCI_GUSB2PHYCFG_FSINTF_SHIFT -#undef USB3_0_XHCI_GUSB2PHYCFG_FSINTF_MASK -#define USB3_0_XHCI_GUSB2PHYCFG_FSINTF_DEFVAL 0x00000000 -#define USB3_0_XHCI_GUSB2PHYCFG_FSINTF_SHIFT 5 -#define USB3_0_XHCI_GUSB2PHYCFG_FSINTF_MASK 0x00000020U - -/*ULPI or UTMI+ Select (ULPI_UTMI_Sel) The application uses this bit to select a UTMI+ or ULPI Interface. - 1'b0: UTMI+ Interfa - e - 1'b1: ULPI Interface This bit is writable only if UTMI+ and ULPI is specified for High-Speed PHY Interface(s) in coreCons - ltant configuration (DWC_USB3_HSPHY_INTERFACE = 3). Otherwise, this bit is read-only and the value depends on the interface s - lected through DWC_USB3_HSPHY_INTERFACE.*/ -#undef USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL_DEFVAL -#undef USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL_SHIFT -#undef USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL_MASK -#define USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL_DEFVAL 0x00000000 -#define USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL_SHIFT 4 -#define USB3_0_XHCI_GUSB2PHYCFG_ULPI_UTMI_SEL_MASK 0x00000010U - -/*PHY Interface (PHYIf) If UTMI+ is selected, the application uses this bit to configure the core to support a UTMI+ PHY with a - 8- or 16-bit interface. - 1'b0: 8 bits - 1'b1: 16 bits ULPI Mode: 1'b0 Note: - All the enabled 2.0 ports must have the same - lock frequency as Port0 clock frequency (utmi_clk[0]). - The UTMI 8-bit and 16-bit modes cannot be used together for differen - ports at the same time (that is, all the ports must be in 8-bit mode, or all of them must be in 16-bit mode, at a time). - I - any of the USB 2.0 ports is selected as ULPI port for operation, then all the USB 2.0 ports must be operating at 60 MHz.*/ -#undef USB3_0_XHCI_GUSB2PHYCFG_PHYIF_DEFVAL -#undef USB3_0_XHCI_GUSB2PHYCFG_PHYIF_SHIFT -#undef USB3_0_XHCI_GUSB2PHYCFG_PHYIF_MASK -#define USB3_0_XHCI_GUSB2PHYCFG_PHYIF_DEFVAL 0x00000000 -#define USB3_0_XHCI_GUSB2PHYCFG_PHYIF_SHIFT 3 -#define USB3_0_XHCI_GUSB2PHYCFG_PHYIF_MASK 0x00000008U - -/*HS/FS Timeout Calibration (TOutCal) The number of PHY clocks, as indicated by the application in this field, is multiplied by - a bit-time factor; this factor is added to the high-speed/full-speed interpacket timeout duration in the core to account for - dditional delays introduced by the PHY. This may be required, since the delay introduced by the PHY in generating the linesta - e condition may vary among PHYs. The USB standard timeout value for high-speed operation is 736 to 816 (inclusive) bit times. - The USB standard timeout value for full-speed operation is 16 to 18 (inclusive) bit times. The application must program this - ield based on the speed of connection. The number of bit times added per PHY clock are: High-speed operation: - One 30-MHz PH - clock = 16 bit times - One 60-MHz PHY clock = 8 bit times Full-speed operation: - One 30-MHz PHY clock = 0.4 bit times - One - 60-MHz PHY clock = 0.2 bit times - One 48-MHz PHY clock = 0.25 bit times*/ -#undef USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL_DEFVAL -#undef USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL_SHIFT -#undef USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL_MASK -#define USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL_DEFVAL 0x00000000 -#define USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL_SHIFT 0 -#define USB3_0_XHCI_GUSB2PHYCFG_TOUTCAL_MASK 0x00000007U - -/*This field indicates the frame length adjustment to be applied when SOF/ITP counter is running on the ref_clk. This register - alue is used to adjust the ITP interval when GCTL[SOFITPSYNC] is set to '1'; SOF and ITP interval when GLADJ.GFLADJ_REFCLK_LP - _SEL is set to '1'. This field must be programmed to a non-zero value only if GFLADJ_REFCLK_LPM_SEL is set to '1' or GCTL.SOF - TPSYNC is set to '1'. The value is derived as follows: FLADJ_REF_CLK_FLADJ=((125000/ref_clk_period_integer)-(125000/ref_clk_p - riod)) * ref_clk_period where - the ref_clk_period_integer is the integer value of the ref_clk period got by truncating the d - cimal (fractional) value that is programmed in the GUCTL.REF_CLK_PERIOD field. - the ref_clk_period is the ref_clk period inc - uding the fractional value. Examples: If the ref_clk is 24 MHz then - GUCTL.REF_CLK_PERIOD = 41 - GFLADJ.GLADJ_REFCLK_FLADJ = - ((125000/41)-(125000/41.6666))*41.6666 = 2032 (ignoring the fractional value) If the ref_clk is 48 MHz then - GUCTL.REF_CLK_P - RIOD = 20 - GFLADJ.GLADJ_REFCLK_FLADJ = ((125000/20)-(125000/20.8333))*20.8333 = 5208 (ignoring the fractional value)*/ -#undef USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ_DEFVAL -#undef USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ_SHIFT -#undef USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ_MASK -#define USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ_DEFVAL 0x00000000 -#define USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ_SHIFT 8 -#define USB3_0_XHCI_GFLADJ_GFLADJ_REFCLK_FLADJ_MASK 0x003FFF00U - -/*If TRUE Completion Timeout Disable is supported. This is required to be TRUE for Endpoint and either setting allowed for Root - ports. Drives Device Capability 2 [4]; EP=0x0001; RP=0x0001*/ -#undef PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED_DEFVAL -#undef PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED_SHIFT -#undef PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED_MASK -#define PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED_DEFVAL 0x00000905 -#define PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED_SHIFT 9 -#define PCIE_ATTRIB_ATTR_25_ATTR_CPL_TIMEOUT_DISABLE_SUPPORTED_MASK 0x00000200U - -/*Status Read value of PLL Lock*/ -#undef SERDES_L1_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_DEFVAL -#undef SERDES_L1_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_SHIFT -#undef SERDES_L1_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_MASK -#define SERDES_L1_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_DEFVAL 0x00000001 -#define SERDES_L1_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_SHIFT 4 -#define SERDES_L1_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_MASK 0x00000010U -#define SERDES_L1_PLL_STATUS_READ_1_OFFSET 0XFD4063E4 - -/*Status Read value of PLL Lock*/ -#undef SERDES_L2_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_DEFVAL -#undef SERDES_L2_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_SHIFT -#undef SERDES_L2_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_MASK -#define SERDES_L2_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_DEFVAL 0x00000001 -#define SERDES_L2_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_SHIFT 4 -#define SERDES_L2_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_MASK 0x00000010U -#define SERDES_L2_PLL_STATUS_READ_1_OFFSET 0XFD40A3E4 - -/*Status Read value of PLL Lock*/ -#undef SERDES_L3_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_DEFVAL -#undef SERDES_L3_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_SHIFT -#undef SERDES_L3_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_MASK -#define SERDES_L3_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_DEFVAL 0x00000001 -#define SERDES_L3_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_SHIFT 4 -#define SERDES_L3_PLL_STATUS_READ_1_PLL_LOCK_STATUS_READ_MASK 0x00000010U -#define SERDES_L3_PLL_STATUS_READ_1_OFFSET 0XFD40E3E4 - -/*CIBGMN: COMINIT Burst Gap Minimum.*/ -#undef SATA_AHCI_VENDOR_PP2C_CIBGMN_DEFVAL -#undef SATA_AHCI_VENDOR_PP2C_CIBGMN_SHIFT -#undef SATA_AHCI_VENDOR_PP2C_CIBGMN_MASK -#define SATA_AHCI_VENDOR_PP2C_CIBGMN_DEFVAL 0x28184D1B -#define SATA_AHCI_VENDOR_PP2C_CIBGMN_SHIFT 0 -#define SATA_AHCI_VENDOR_PP2C_CIBGMN_MASK 0x000000FFU - -/*CIBGMX: COMINIT Burst Gap Maximum.*/ -#undef SATA_AHCI_VENDOR_PP2C_CIBGMX_DEFVAL -#undef SATA_AHCI_VENDOR_PP2C_CIBGMX_SHIFT -#undef SATA_AHCI_VENDOR_PP2C_CIBGMX_MASK -#define SATA_AHCI_VENDOR_PP2C_CIBGMX_DEFVAL 0x28184D1B -#define SATA_AHCI_VENDOR_PP2C_CIBGMX_SHIFT 8 -#define SATA_AHCI_VENDOR_PP2C_CIBGMX_MASK 0x0000FF00U - -/*CIBGN: COMINIT Burst Gap Nominal.*/ -#undef SATA_AHCI_VENDOR_PP2C_CIBGN_DEFVAL -#undef SATA_AHCI_VENDOR_PP2C_CIBGN_SHIFT -#undef SATA_AHCI_VENDOR_PP2C_CIBGN_MASK -#define SATA_AHCI_VENDOR_PP2C_CIBGN_DEFVAL 0x28184D1B -#define SATA_AHCI_VENDOR_PP2C_CIBGN_SHIFT 16 -#define SATA_AHCI_VENDOR_PP2C_CIBGN_MASK 0x00FF0000U - -/*CINMP: COMINIT Negate Minimum Period.*/ -#undef SATA_AHCI_VENDOR_PP2C_CINMP_DEFVAL -#undef SATA_AHCI_VENDOR_PP2C_CINMP_SHIFT -#undef SATA_AHCI_VENDOR_PP2C_CINMP_MASK -#define SATA_AHCI_VENDOR_PP2C_CINMP_DEFVAL 0x28184D1B -#define SATA_AHCI_VENDOR_PP2C_CINMP_SHIFT 24 -#define SATA_AHCI_VENDOR_PP2C_CINMP_MASK 0xFF000000U - -/*CWBGMN: COMWAKE Burst Gap Minimum.*/ -#undef SATA_AHCI_VENDOR_PP3C_CWBGMN_DEFVAL -#undef SATA_AHCI_VENDOR_PP3C_CWBGMN_SHIFT -#undef SATA_AHCI_VENDOR_PP3C_CWBGMN_MASK -#define SATA_AHCI_VENDOR_PP3C_CWBGMN_DEFVAL 0x0E081906 -#define SATA_AHCI_VENDOR_PP3C_CWBGMN_SHIFT 0 -#define SATA_AHCI_VENDOR_PP3C_CWBGMN_MASK 0x000000FFU - -/*CWBGMX: COMWAKE Burst Gap Maximum.*/ -#undef SATA_AHCI_VENDOR_PP3C_CWBGMX_DEFVAL -#undef SATA_AHCI_VENDOR_PP3C_CWBGMX_SHIFT -#undef SATA_AHCI_VENDOR_PP3C_CWBGMX_MASK -#define SATA_AHCI_VENDOR_PP3C_CWBGMX_DEFVAL 0x0E081906 -#define SATA_AHCI_VENDOR_PP3C_CWBGMX_SHIFT 8 -#define SATA_AHCI_VENDOR_PP3C_CWBGMX_MASK 0x0000FF00U - -/*CWBGN: COMWAKE Burst Gap Nominal.*/ -#undef SATA_AHCI_VENDOR_PP3C_CWBGN_DEFVAL -#undef SATA_AHCI_VENDOR_PP3C_CWBGN_SHIFT -#undef SATA_AHCI_VENDOR_PP3C_CWBGN_MASK -#define SATA_AHCI_VENDOR_PP3C_CWBGN_DEFVAL 0x0E081906 -#define SATA_AHCI_VENDOR_PP3C_CWBGN_SHIFT 16 -#define SATA_AHCI_VENDOR_PP3C_CWBGN_MASK 0x00FF0000U - -/*CWNMP: COMWAKE Negate Minimum Period.*/ -#undef SATA_AHCI_VENDOR_PP3C_CWNMP_DEFVAL -#undef SATA_AHCI_VENDOR_PP3C_CWNMP_SHIFT -#undef SATA_AHCI_VENDOR_PP3C_CWNMP_MASK -#define SATA_AHCI_VENDOR_PP3C_CWNMP_DEFVAL 0x0E081906 -#define SATA_AHCI_VENDOR_PP3C_CWNMP_SHIFT 24 -#define SATA_AHCI_VENDOR_PP3C_CWNMP_MASK 0xFF000000U - -/*BMX: COM Burst Maximum.*/ -#undef SATA_AHCI_VENDOR_PP4C_BMX_DEFVAL -#undef SATA_AHCI_VENDOR_PP4C_BMX_SHIFT -#undef SATA_AHCI_VENDOR_PP4C_BMX_MASK -#define SATA_AHCI_VENDOR_PP4C_BMX_DEFVAL 0x064A0813 -#define SATA_AHCI_VENDOR_PP4C_BMX_SHIFT 0 -#define SATA_AHCI_VENDOR_PP4C_BMX_MASK 0x000000FFU - -/*BNM: COM Burst Nominal.*/ -#undef SATA_AHCI_VENDOR_PP4C_BNM_DEFVAL -#undef SATA_AHCI_VENDOR_PP4C_BNM_SHIFT -#undef SATA_AHCI_VENDOR_PP4C_BNM_MASK -#define SATA_AHCI_VENDOR_PP4C_BNM_DEFVAL 0x064A0813 -#define SATA_AHCI_VENDOR_PP4C_BNM_SHIFT 8 -#define SATA_AHCI_VENDOR_PP4C_BNM_MASK 0x0000FF00U - -/*SFD: Signal Failure Detection, if the signal detection de-asserts for a time greater than this then the OOB detector will det - rmine this is a line idle and cause the PhyInit state machine to exit the Phy Ready State. A value of zero disables the Signa - Failure Detector. The value is based on the OOB Detector Clock typically (PMCLK Clock Period) * SFD giving a nominal time of - 500ns based on a 150MHz PMCLK.*/ -#undef SATA_AHCI_VENDOR_PP4C_SFD_DEFVAL -#undef SATA_AHCI_VENDOR_PP4C_SFD_SHIFT -#undef SATA_AHCI_VENDOR_PP4C_SFD_MASK -#define SATA_AHCI_VENDOR_PP4C_SFD_DEFVAL 0x064A0813 -#define SATA_AHCI_VENDOR_PP4C_SFD_SHIFT 16 -#define SATA_AHCI_VENDOR_PP4C_SFD_MASK 0x00FF0000U - -/*PTST: Partial to Slumber timer value, specific delay the controller should apply while in partial before entering slumber. Th - value is bases on the system clock divided by 128, total delay = (Sys Clock Period) * PTST * 128*/ -#undef SATA_AHCI_VENDOR_PP4C_PTST_DEFVAL -#undef SATA_AHCI_VENDOR_PP4C_PTST_SHIFT -#undef SATA_AHCI_VENDOR_PP4C_PTST_MASK -#define SATA_AHCI_VENDOR_PP4C_PTST_DEFVAL 0x064A0813 -#define SATA_AHCI_VENDOR_PP4C_PTST_SHIFT 24 -#define SATA_AHCI_VENDOR_PP4C_PTST_MASK 0xFF000000U - -/*RIT: Retry Interval Timer. The calculated value divided by two, the lower digit of precision is not needed.*/ -#undef SATA_AHCI_VENDOR_PP5C_RIT_DEFVAL -#undef SATA_AHCI_VENDOR_PP5C_RIT_SHIFT -#undef SATA_AHCI_VENDOR_PP5C_RIT_MASK -#define SATA_AHCI_VENDOR_PP5C_RIT_DEFVAL 0x3FFC96A4 -#define SATA_AHCI_VENDOR_PP5C_RIT_SHIFT 0 -#define SATA_AHCI_VENDOR_PP5C_RIT_MASK 0x000FFFFFU - -/*RCT: Rate Change Timer, a value based on the 54.2us for which a SATA device will transmit at a fixed rate ALIGNp after OOB ha - completed, for a fast SERDES it is suggested that this value be 54.2us / 4*/ -#undef SATA_AHCI_VENDOR_PP5C_RCT_DEFVAL -#undef SATA_AHCI_VENDOR_PP5C_RCT_SHIFT -#undef SATA_AHCI_VENDOR_PP5C_RCT_MASK -#define SATA_AHCI_VENDOR_PP5C_RCT_DEFVAL 0x3FFC96A4 -#define SATA_AHCI_VENDOR_PP5C_RCT_SHIFT 20 -#define SATA_AHCI_VENDOR_PP5C_RCT_MASK 0xFFF00000U -#undef CRL_APB_RST_LPD_TOP_OFFSET -#define CRL_APB_RST_LPD_TOP_OFFSET 0XFF5E023C -#undef CRL_APB_RST_LPD_IOU0_OFFSET -#define CRL_APB_RST_LPD_IOU0_OFFSET 0XFF5E0230 -#undef CRF_APB_RST_FPD_TOP_OFFSET -#define CRF_APB_RST_FPD_TOP_OFFSET 0XFD1A0100 -#undef DP_DP_TX_PHY_POWER_DOWN_OFFSET -#define DP_DP_TX_PHY_POWER_DOWN_OFFSET 0XFD4A0238 -#undef DP_DP_PHY_RESET_OFFSET -#define DP_DP_PHY_RESET_OFFSET 0XFD4A0200 -#undef CRF_APB_RST_FPD_TOP_OFFSET -#define CRF_APB_RST_FPD_TOP_OFFSET 0XFD1A0100 - -/*USB 0 reset for control registers*/ -#undef CRL_APB_RST_LPD_TOP_USB0_APB_RESET_DEFVAL -#undef CRL_APB_RST_LPD_TOP_USB0_APB_RESET_SHIFT -#undef CRL_APB_RST_LPD_TOP_USB0_APB_RESET_MASK -#define CRL_APB_RST_LPD_TOP_USB0_APB_RESET_DEFVAL 0x00188FDF -#define CRL_APB_RST_LPD_TOP_USB0_APB_RESET_SHIFT 10 -#define CRL_APB_RST_LPD_TOP_USB0_APB_RESET_MASK 0x00000400U - -/*USB 0 sleep circuit reset*/ -#undef CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_DEFVAL -#undef CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_SHIFT -#undef CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_MASK -#define CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_DEFVAL 0x00188FDF -#define CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_SHIFT 8 -#define CRL_APB_RST_LPD_TOP_USB0_HIBERRESET_MASK 0x00000100U - -/*USB 0 reset*/ -#undef CRL_APB_RST_LPD_TOP_USB0_CORERESET_DEFVAL -#undef CRL_APB_RST_LPD_TOP_USB0_CORERESET_SHIFT -#undef CRL_APB_RST_LPD_TOP_USB0_CORERESET_MASK -#define CRL_APB_RST_LPD_TOP_USB0_CORERESET_DEFVAL 0x00188FDF -#define CRL_APB_RST_LPD_TOP_USB0_CORERESET_SHIFT 6 -#define CRL_APB_RST_LPD_TOP_USB0_CORERESET_MASK 0x00000040U - -/*GEM 3 reset*/ -#undef CRL_APB_RST_LPD_IOU0_GEM3_RESET_DEFVAL -#undef CRL_APB_RST_LPD_IOU0_GEM3_RESET_SHIFT -#undef CRL_APB_RST_LPD_IOU0_GEM3_RESET_MASK -#define CRL_APB_RST_LPD_IOU0_GEM3_RESET_DEFVAL 0x0000000F -#define CRL_APB_RST_LPD_IOU0_GEM3_RESET_SHIFT 3 -#define CRL_APB_RST_LPD_IOU0_GEM3_RESET_MASK 0x00000008U - -/*Sata block level reset*/ -#undef CRF_APB_RST_FPD_TOP_SATA_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_SATA_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_SATA_RESET_MASK -#define CRF_APB_RST_FPD_TOP_SATA_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_SATA_RESET_SHIFT 1 -#define CRF_APB_RST_FPD_TOP_SATA_RESET_MASK 0x00000002U - -/*Two bits per lane. When set to 11, moves the GT to power down mode. When set to 00, GT will be in active state. bits [1:0] - - ane0 Bits [3:2] - lane 1*/ -#undef DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_DEFVAL -#undef DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_SHIFT -#undef DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_MASK -#define DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_DEFVAL 0x00000000 -#define DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_SHIFT 0 -#define DP_DP_TX_PHY_POWER_DOWN_POWER_DWN_MASK 0x0000000FU - -/*Set to '1' to hold the GT in reset. Clear to release.*/ -#undef DP_DP_PHY_RESET_GT_RESET_DEFVAL -#undef DP_DP_PHY_RESET_GT_RESET_SHIFT -#undef DP_DP_PHY_RESET_GT_RESET_MASK -#define DP_DP_PHY_RESET_GT_RESET_DEFVAL 0x00010003 -#define DP_DP_PHY_RESET_GT_RESET_SHIFT 1 -#define DP_DP_PHY_RESET_GT_RESET_MASK 0x00000002U - -/*Display Port block level reset (includes DPDMA)*/ -#undef CRF_APB_RST_FPD_TOP_DP_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_DP_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_DP_RESET_MASK -#define CRF_APB_RST_FPD_TOP_DP_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_DP_RESET_SHIFT 16 -#define CRF_APB_RST_FPD_TOP_DP_RESET_MASK 0x00010000U -#undef CRF_APB_RST_FPD_TOP_OFFSET -#define CRF_APB_RST_FPD_TOP_OFFSET 0XFD1A0100 -#undef CRL_APB_RST_LPD_TOP_OFFSET -#define CRL_APB_RST_LPD_TOP_OFFSET 0XFF5E023C -#undef FPD_SLCR_AFI_FS_OFFSET -#define FPD_SLCR_AFI_FS_OFFSET 0XFD615000 -#undef LPD_SLCR_AFI_FS_OFFSET -#define LPD_SLCR_AFI_FS_OFFSET 0XFF419000 -#undef AFIFM0_AFIFM_RDCTRL_OFFSET -#define AFIFM0_AFIFM_RDCTRL_OFFSET 0XFD360000 -#undef AFIFM1_AFIFM_RDCTRL_OFFSET -#define AFIFM1_AFIFM_RDCTRL_OFFSET 0XFD370000 -#undef AFIFM2_AFIFM_RDCTRL_OFFSET -#define AFIFM2_AFIFM_RDCTRL_OFFSET 0XFD380000 -#undef AFIFM3_AFIFM_RDCTRL_OFFSET -#define AFIFM3_AFIFM_RDCTRL_OFFSET 0XFD390000 -#undef AFIFM4_AFIFM_RDCTRL_OFFSET -#define AFIFM4_AFIFM_RDCTRL_OFFSET 0XFD3A0000 -#undef AFIFM5_AFIFM_RDCTRL_OFFSET -#define AFIFM5_AFIFM_RDCTRL_OFFSET 0XFD3B0000 -#undef AFIFM6_AFIFM_RDCTRL_OFFSET -#define AFIFM6_AFIFM_RDCTRL_OFFSET 0XFF9B0000 -#undef AFIFM0_AFIFM_WRCTRL_OFFSET -#define AFIFM0_AFIFM_WRCTRL_OFFSET 0XFD360014 -#undef AFIFM1_AFIFM_WRCTRL_OFFSET -#define AFIFM1_AFIFM_WRCTRL_OFFSET 0XFD370014 -#undef AFIFM2_AFIFM_WRCTRL_OFFSET -#define AFIFM2_AFIFM_WRCTRL_OFFSET 0XFD380014 -#undef AFIFM3_AFIFM_WRCTRL_OFFSET -#define AFIFM3_AFIFM_WRCTRL_OFFSET 0XFD390014 -#undef AFIFM4_AFIFM_WRCTRL_OFFSET -#define AFIFM4_AFIFM_WRCTRL_OFFSET 0XFD3A0014 -#undef AFIFM5_AFIFM_WRCTRL_OFFSET -#define AFIFM5_AFIFM_WRCTRL_OFFSET 0XFD3B0014 -#undef AFIFM6_AFIFM_WRCTRL_OFFSET -#define AFIFM6_AFIFM_WRCTRL_OFFSET 0XFF9B0014 -#undef PMU_GLOBAL_REQ_PWRUP_INT_EN_OFFSET -#define PMU_GLOBAL_REQ_PWRUP_INT_EN_OFFSET 0XFFD80118 -#undef PMU_GLOBAL_REQ_PWRUP_TRIG_OFFSET -#define PMU_GLOBAL_REQ_PWRUP_TRIG_OFFSET 0XFFD80120 - -/*AF_FM0 block level reset*/ -#undef CRF_APB_RST_FPD_TOP_AFI_FM0_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_AFI_FM0_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_AFI_FM0_RESET_MASK -#define CRF_APB_RST_FPD_TOP_AFI_FM0_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_AFI_FM0_RESET_SHIFT 7 -#define CRF_APB_RST_FPD_TOP_AFI_FM0_RESET_MASK 0x00000080U - -/*AF_FM1 block level reset*/ -#undef CRF_APB_RST_FPD_TOP_AFI_FM1_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_AFI_FM1_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_AFI_FM1_RESET_MASK -#define CRF_APB_RST_FPD_TOP_AFI_FM1_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_AFI_FM1_RESET_SHIFT 8 -#define CRF_APB_RST_FPD_TOP_AFI_FM1_RESET_MASK 0x00000100U - -/*AF_FM2 block level reset*/ -#undef CRF_APB_RST_FPD_TOP_AFI_FM2_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_AFI_FM2_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_AFI_FM2_RESET_MASK -#define CRF_APB_RST_FPD_TOP_AFI_FM2_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_AFI_FM2_RESET_SHIFT 9 -#define CRF_APB_RST_FPD_TOP_AFI_FM2_RESET_MASK 0x00000200U - -/*AF_FM3 block level reset*/ -#undef CRF_APB_RST_FPD_TOP_AFI_FM3_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_AFI_FM3_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_AFI_FM3_RESET_MASK -#define CRF_APB_RST_FPD_TOP_AFI_FM3_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_AFI_FM3_RESET_SHIFT 10 -#define CRF_APB_RST_FPD_TOP_AFI_FM3_RESET_MASK 0x00000400U - -/*AF_FM4 block level reset*/ -#undef CRF_APB_RST_FPD_TOP_AFI_FM4_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_AFI_FM4_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_AFI_FM4_RESET_MASK -#define CRF_APB_RST_FPD_TOP_AFI_FM4_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_AFI_FM4_RESET_SHIFT 11 -#define CRF_APB_RST_FPD_TOP_AFI_FM4_RESET_MASK 0x00000800U - -/*AF_FM5 block level reset*/ -#undef CRF_APB_RST_FPD_TOP_AFI_FM5_RESET_DEFVAL -#undef CRF_APB_RST_FPD_TOP_AFI_FM5_RESET_SHIFT -#undef CRF_APB_RST_FPD_TOP_AFI_FM5_RESET_MASK -#define CRF_APB_RST_FPD_TOP_AFI_FM5_RESET_DEFVAL 0x000F9FFE -#define CRF_APB_RST_FPD_TOP_AFI_FM5_RESET_SHIFT 12 -#define CRF_APB_RST_FPD_TOP_AFI_FM5_RESET_MASK 0x00001000U - -/*AFI FM 6*/ -#undef CRL_APB_RST_LPD_TOP_AFI_FM6_RESET_DEFVAL -#undef CRL_APB_RST_LPD_TOP_AFI_FM6_RESET_SHIFT -#undef CRL_APB_RST_LPD_TOP_AFI_FM6_RESET_MASK -#define CRL_APB_RST_LPD_TOP_AFI_FM6_RESET_DEFVAL 0x00188FDF -#define CRL_APB_RST_LPD_TOP_AFI_FM6_RESET_SHIFT 19 -#define CRL_APB_RST_LPD_TOP_AFI_FM6_RESET_MASK 0x00080000U - -/*Select the 32/64/128-bit data width selection for the Slave 0 00: 32-bit AXI data width (default) 01: 64-bit AXI data width 1 - : 128-bit AXI data width 11: reserved*/ -#undef FPD_SLCR_AFI_FS_DW_SS0_SEL_DEFVAL -#undef FPD_SLCR_AFI_FS_DW_SS0_SEL_SHIFT -#undef FPD_SLCR_AFI_FS_DW_SS0_SEL_MASK -#define FPD_SLCR_AFI_FS_DW_SS0_SEL_DEFVAL 0x00000A00 -#define FPD_SLCR_AFI_FS_DW_SS0_SEL_SHIFT 8 -#define FPD_SLCR_AFI_FS_DW_SS0_SEL_MASK 0x00000300U - -/*Select the 32/64/128-bit data width selection for the Slave 1 00: 32-bit AXI data width (default) 01: 64-bit AXI data width 1 - : 128-bit AXI data width 11: reserved*/ -#undef FPD_SLCR_AFI_FS_DW_SS1_SEL_DEFVAL -#undef FPD_SLCR_AFI_FS_DW_SS1_SEL_SHIFT -#undef FPD_SLCR_AFI_FS_DW_SS1_SEL_MASK -#define FPD_SLCR_AFI_FS_DW_SS1_SEL_DEFVAL 0x00000A00 -#define FPD_SLCR_AFI_FS_DW_SS1_SEL_SHIFT 10 -#define FPD_SLCR_AFI_FS_DW_SS1_SEL_MASK 0x00000C00U - -/*Select the 32/64/128-bit data width selection for the Slave 0 00: 32-bit AXI data width (default) 01: 64-bit AXI data width 1 - : 128-bit AXI data width 11: reserved*/ -#undef LPD_SLCR_AFI_FS_DW_SS2_SEL_DEFVAL -#undef LPD_SLCR_AFI_FS_DW_SS2_SEL_SHIFT -#undef LPD_SLCR_AFI_FS_DW_SS2_SEL_MASK -#define LPD_SLCR_AFI_FS_DW_SS2_SEL_DEFVAL 0x00000200 -#define LPD_SLCR_AFI_FS_DW_SS2_SEL_SHIFT 8 -#define LPD_SLCR_AFI_FS_DW_SS2_SEL_MASK 0x00000300U - -/*Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled*/ -#undef AFIFM0_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM0_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM0_AFIFM_RDCTRL_FABRIC_WIDTH_MASK -#define AFIFM0_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM0_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM0_AFIFM_RDCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled*/ -#undef AFIFM1_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM1_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM1_AFIFM_RDCTRL_FABRIC_WIDTH_MASK -#define AFIFM1_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM1_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM1_AFIFM_RDCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled*/ -#undef AFIFM2_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM2_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM2_AFIFM_RDCTRL_FABRIC_WIDTH_MASK -#define AFIFM2_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM2_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM2_AFIFM_RDCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled*/ -#undef AFIFM3_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM3_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM3_AFIFM_RDCTRL_FABRIC_WIDTH_MASK -#define AFIFM3_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM3_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM3_AFIFM_RDCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled*/ -#undef AFIFM4_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM4_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM4_AFIFM_RDCTRL_FABRIC_WIDTH_MASK -#define AFIFM4_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM4_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM4_AFIFM_RDCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled*/ -#undef AFIFM5_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM5_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM5_AFIFM_RDCTRL_FABRIC_WIDTH_MASK -#define AFIFM5_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM5_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM5_AFIFM_RDCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Read Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 128 - bit enabled*/ -#undef AFIFM6_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM6_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM6_AFIFM_RDCTRL_FABRIC_WIDTH_MASK -#define AFIFM6_AFIFM_RDCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM6_AFIFM_RDCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM6_AFIFM_RDCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled*/ -#undef AFIFM0_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM0_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM0_AFIFM_WRCTRL_FABRIC_WIDTH_MASK -#define AFIFM0_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM0_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM0_AFIFM_WRCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled*/ -#undef AFIFM1_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM1_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM1_AFIFM_WRCTRL_FABRIC_WIDTH_MASK -#define AFIFM1_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM1_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM1_AFIFM_WRCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled*/ -#undef AFIFM2_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM2_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM2_AFIFM_WRCTRL_FABRIC_WIDTH_MASK -#define AFIFM2_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM2_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM2_AFIFM_WRCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled*/ -#undef AFIFM3_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM3_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM3_AFIFM_WRCTRL_FABRIC_WIDTH_MASK -#define AFIFM3_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM3_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM3_AFIFM_WRCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled*/ -#undef AFIFM4_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM4_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM4_AFIFM_WRCTRL_FABRIC_WIDTH_MASK -#define AFIFM4_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM4_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM4_AFIFM_WRCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled*/ -#undef AFIFM5_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM5_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM5_AFIFM_WRCTRL_FABRIC_WIDTH_MASK -#define AFIFM5_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM5_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM5_AFIFM_WRCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Configures the Write Channel Fabric interface width. 2'b11 : Reserved 2'b10 : 32-bit Fabric 2'b01 : 64-bit enabled 2'b00 : 12 - -bit enabled*/ -#undef AFIFM6_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL -#undef AFIFM6_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT -#undef AFIFM6_AFIFM_WRCTRL_FABRIC_WIDTH_MASK -#define AFIFM6_AFIFM_WRCTRL_FABRIC_WIDTH_DEFVAL 0x000003B0 -#define AFIFM6_AFIFM_WRCTRL_FABRIC_WIDTH_SHIFT 0 -#define AFIFM6_AFIFM_WRCTRL_FABRIC_WIDTH_MASK 0x00000003U - -/*Power-up Request Interrupt Enable for PL*/ -#undef PMU_GLOBAL_REQ_PWRUP_INT_EN_PL_DEFVAL -#undef PMU_GLOBAL_REQ_PWRUP_INT_EN_PL_SHIFT -#undef PMU_GLOBAL_REQ_PWRUP_INT_EN_PL_MASK -#define PMU_GLOBAL_REQ_PWRUP_INT_EN_PL_DEFVAL 0x00000000 -#define PMU_GLOBAL_REQ_PWRUP_INT_EN_PL_SHIFT 23 -#define PMU_GLOBAL_REQ_PWRUP_INT_EN_PL_MASK 0x00800000U - -/*Power-up Request Trigger for PL*/ -#undef PMU_GLOBAL_REQ_PWRUP_TRIG_PL_DEFVAL -#undef PMU_GLOBAL_REQ_PWRUP_TRIG_PL_SHIFT -#undef PMU_GLOBAL_REQ_PWRUP_TRIG_PL_MASK -#define PMU_GLOBAL_REQ_PWRUP_TRIG_PL_DEFVAL 0x00000000 -#define PMU_GLOBAL_REQ_PWRUP_TRIG_PL_SHIFT 23 -#define PMU_GLOBAL_REQ_PWRUP_TRIG_PL_MASK 0x00800000U - -/*Power-up Request Status for PL*/ -#undef PMU_GLOBAL_REQ_PWRUP_STATUS_PL_DEFVAL -#undef PMU_GLOBAL_REQ_PWRUP_STATUS_PL_SHIFT -#undef PMU_GLOBAL_REQ_PWRUP_STATUS_PL_MASK -#define PMU_GLOBAL_REQ_PWRUP_STATUS_PL_DEFVAL 0x00000000 -#define PMU_GLOBAL_REQ_PWRUP_STATUS_PL_SHIFT 23 -#define PMU_GLOBAL_REQ_PWRUP_STATUS_PL_MASK 0x00800000U -#define PMU_GLOBAL_REQ_PWRUP_STATUS_OFFSET 0XFFD80110 -#undef GPIO_MASK_DATA_5_MSW_OFFSET -#define GPIO_MASK_DATA_5_MSW_OFFSET 0XFF0A002C -#undef GPIO_DIRM_5_OFFSET -#define GPIO_DIRM_5_OFFSET 0XFF0A0344 -#undef GPIO_OEN_5_OFFSET -#define GPIO_OEN_5_OFFSET 0XFF0A0348 -#undef GPIO_DATA_5_OFFSET -#define GPIO_DATA_5_OFFSET 0XFF0A0054 -#undef GPIO_DATA_5_OFFSET -#define GPIO_DATA_5_OFFSET 0XFF0A0054 -#undef GPIO_DATA_5_OFFSET -#define GPIO_DATA_5_OFFSET 0XFF0A0054 - -/*Operation is the same as MASK_DATA_0_LSW[MASK_0_LSW]*/ -#undef GPIO_MASK_DATA_5_MSW_MASK_5_MSW_DEFVAL -#undef GPIO_MASK_DATA_5_MSW_MASK_5_MSW_SHIFT -#undef GPIO_MASK_DATA_5_MSW_MASK_5_MSW_MASK -#define GPIO_MASK_DATA_5_MSW_MASK_5_MSW_DEFVAL 0x00000000 -#define GPIO_MASK_DATA_5_MSW_MASK_5_MSW_SHIFT 16 -#define GPIO_MASK_DATA_5_MSW_MASK_5_MSW_MASK 0xFFFF0000U - -/*Operation is the same as DIRM_0[DIRECTION_0]*/ -#undef GPIO_DIRM_5_DIRECTION_5_DEFVAL -#undef GPIO_DIRM_5_DIRECTION_5_SHIFT -#undef GPIO_DIRM_5_DIRECTION_5_MASK -#define GPIO_DIRM_5_DIRECTION_5_DEFVAL -#define GPIO_DIRM_5_DIRECTION_5_SHIFT 0 -#define GPIO_DIRM_5_DIRECTION_5_MASK 0xFFFFFFFFU - -/*Operation is the same as OEN_0[OP_ENABLE_0]*/ -#undef GPIO_OEN_5_OP_ENABLE_5_DEFVAL -#undef GPIO_OEN_5_OP_ENABLE_5_SHIFT -#undef GPIO_OEN_5_OP_ENABLE_5_MASK -#define GPIO_OEN_5_OP_ENABLE_5_DEFVAL -#define GPIO_OEN_5_OP_ENABLE_5_SHIFT 0 -#define GPIO_OEN_5_OP_ENABLE_5_MASK 0xFFFFFFFFU - -/*Output Data*/ -#undef GPIO_DATA_5_DATA_5_DEFVAL -#undef GPIO_DATA_5_DATA_5_SHIFT -#undef GPIO_DATA_5_DATA_5_MASK -#define GPIO_DATA_5_DATA_5_DEFVAL -#define GPIO_DATA_5_DATA_5_SHIFT 0 -#define GPIO_DATA_5_DATA_5_MASK 0xFFFFFFFFU - -/*Output Data*/ -#undef GPIO_DATA_5_DATA_5_DEFVAL -#undef GPIO_DATA_5_DATA_5_SHIFT -#undef GPIO_DATA_5_DATA_5_MASK -#define GPIO_DATA_5_DATA_5_DEFVAL -#define GPIO_DATA_5_DATA_5_SHIFT 0 -#define GPIO_DATA_5_DATA_5_MASK 0xFFFFFFFFU - -/*Output Data*/ -#undef GPIO_DATA_5_DATA_5_DEFVAL -#undef GPIO_DATA_5_DATA_5_SHIFT -#undef GPIO_DATA_5_DATA_5_MASK -#define GPIO_DATA_5_DATA_5_DEFVAL -#define GPIO_DATA_5_DATA_5_SHIFT 0 -#define GPIO_DATA_5_DATA_5_MASK 0xFFFFFFFFU -#ifdef __cplusplus -extern "C" { -#endif - int psu_init (); - unsigned long psu_ps_pl_isolation_removal_data(); - unsigned long psu_ps_pl_reset_config_data(); - int psu_protection(); - int psu_fpd_protection(); - int psu_ocm_protection(); - int psu_ddr_protection(); - int psu_lpd_protection(); - int psu_protection_lock(); - unsigned long psu_apply_master_tz(); -#ifdef __cplusplus -} -#endif diff --git a/board/xilinx/zynqmp/zynqmp.c b/board/xilinx/zynqmp/zynqmp.c index 9136c46cc7..cef1f6a13a 100644 --- a/board/xilinx/zynqmp/zynqmp.c +++ b/board/xilinx/zynqmp/zynqmp.c @@ -180,75 +180,123 @@ int zynq_board_read_rom_ethaddr(unsigned char *ethaddr) } #if !defined(CONFIG_SYS_SDRAM_BASE) && !defined(CONFIG_SYS_SDRAM_SIZE) -static const void *get_memory_reg_prop(const void *fdt, int *lenp) -{ - int offset; - - offset = fdt_path_offset(fdt, "/memory"); - if (offset < 0) - return NULL; - - return fdt_getprop(fdt, offset, "reg", lenp); -} - -int dram_init(void) +/* + * fdt_get_reg - Fill buffer by information from DT + */ +static phys_size_t fdt_get_reg(const void *fdt, int nodeoffset, void *buf, + const u32 *cell, int n) { - const void *fdt = gd->fdt_blob; - const fdt32_t *val; - int ac, sc, len; - - ac = fdt_address_cells(fdt, 0); - sc = fdt_size_cells(fdt, 0); - if (ac < 0 || sc < 1 || sc > 2) { - printf("invalid address/size cells\n"); - return -EINVAL; + int i = 0, b, banks; + int parent_offset = fdt_parent_offset(fdt, nodeoffset); + int address_cells = fdt_address_cells(fdt, parent_offset); + int size_cells = fdt_size_cells(fdt, parent_offset); + char *p = buf; + u64 val; + u64 vals; + + debug("%s: addr_cells=%x, size_cell=%x, buf=%p, cell=%p\n", + __func__, address_cells, size_cells, buf, cell); + + /* Check memory bank setup */ + banks = n % (address_cells + size_cells); + if (banks) + panic("Incorrect memory setup cells=%d, ac=%d, sc=%d\n", + n, address_cells, size_cells); + + banks = n / (address_cells + size_cells); + + for (b = 0; b < banks; b++) { + debug("%s: Bank #%d:\n", __func__, b); + if (address_cells == 2) { + val = cell[i + 1]; + val <<= 32; + val |= cell[i]; + val = fdt64_to_cpu(val); + debug("%s: addr64=%llx, ptr=%p, cell=%p\n", + __func__, val, p, &cell[i]); + *(phys_addr_t *)p = val; + } else { + debug("%s: addr32=%x, ptr=%p\n", + __func__, fdt32_to_cpu(cell[i]), p); + *(phys_addr_t *)p = fdt32_to_cpu(cell[i]); + } + p += sizeof(phys_addr_t); + i += address_cells; + + debug("%s: pa=%p, i=%x, size=%zu\n", __func__, p, i, + sizeof(phys_addr_t)); + + if (size_cells == 2) { + vals = cell[i + 1]; + vals <<= 32; + vals |= cell[i]; + vals = fdt64_to_cpu(vals); + + debug("%s: size64=%llx, ptr=%p, cell=%p\n", + __func__, vals, p, &cell[i]); + *(phys_size_t *)p = vals; + } else { + debug("%s: size32=%x, ptr=%p\n", + __func__, fdt32_to_cpu(cell[i]), p); + *(phys_size_t *)p = fdt32_to_cpu(cell[i]); + } + p += sizeof(phys_size_t); + i += size_cells; + + debug("%s: ps=%p, i=%x, size=%zu\n", + __func__, p, i, sizeof(phys_size_t)); } - val = get_memory_reg_prop(fdt, &len); - if (len / sizeof(*val) < ac + sc) - return -EINVAL; + /* Return the first address size */ + return *(phys_size_t *)((char *)buf + sizeof(phys_addr_t)); +} - val += ac; +#define FDT_REG_SIZE sizeof(u32) +/* Temp location for sharing data for storing */ +/* Up to 64-bit address + 64-bit size */ +static u8 tmp[CONFIG_NR_DRAM_BANKS * 16]; - gd->ram_size = fdtdec_get_number(val, sc); +void dram_init_banksize(void) +{ + int bank; - debug("DRAM size = %08lx\n", (unsigned long)gd->ram_size); + memcpy(&gd->bd->bi_dram[0], &tmp, sizeof(tmp)); - return 0; + for (bank = 0; bank < CONFIG_NR_DRAM_BANKS; bank++) { + debug("Bank #%d: start %llx\n", bank, + (unsigned long long)gd->bd->bi_dram[bank].start); + debug("Bank #%d: size %llx\n", bank, + (unsigned long long)gd->bd->bi_dram[bank].size); + } } -void dram_init_banksize(void) +int dram_init(void) { - const void *fdt = gd->fdt_blob; - const fdt32_t *val; - int ac, sc, cells, len, i; - - val = get_memory_reg_prop(fdt, &len); - if (len < 0) - return; - - ac = fdt_address_cells(fdt, 0); - sc = fdt_size_cells(fdt, 0); - if (ac < 1 || sc > 2 || sc < 1 || sc > 2) { - printf("invalid address/size cells\n"); - return; + int node, len; + const void *blob = gd->fdt_blob; + const u32 *cell; + + memset(&tmp, 0, sizeof(tmp)); + + /* find or create "/memory" node. */ + node = fdt_subnode_offset(blob, 0, "memory"); + if (node < 0) { + printf("%s: Can't get memory node\n", __func__); + return node; } - cells = ac + sc; + /* Get pointer to cells and lenght of it */ + cell = fdt_getprop(blob, node, "reg", &len); + if (!cell) { + printf("%s: Can't get reg property\n", __func__); + return -1; + } - len /= sizeof(*val); + gd->ram_size = fdt_get_reg(blob, node, &tmp, cell, len / FDT_REG_SIZE); - for (i = 0; i < CONFIG_NR_DRAM_BANKS && len >= cells; - i++, len -= cells) { - gd->bd->bi_dram[i].start = fdtdec_get_number(val, ac); - val += ac; - gd->bd->bi_dram[i].size = fdtdec_get_number(val, sc); - val += sc; + debug("%s: Initial DRAM size %llx\n", __func__, (u64)gd->ram_size); - debug("DRAM bank %d: start = %08lx, size = %08lx\n", - i, (unsigned long)gd->bd->bi_dram[i].start, - (unsigned long)gd->bd->bi_dram[i].size); - } + return 0; } #else int dram_init(void) @@ -263,6 +311,17 @@ void reset_cpu(ulong addr) { } +#ifdef CONFIG_SCSI_AHCI_PLAT +void scsi_init(void) +{ +#if defined(CONFIG_SATA_CEVA) + init_sata(0); +#endif + ahci_init((void __iomem *)ZYNQMP_SATA_BASEADDR); + scsi_scan(1); +} +#endif + int board_late_init(void) { u32 reg = 0; |