summaryrefslogtreecommitdiff
path: root/board
diff options
context:
space:
mode:
Diffstat (limited to 'board')
-rw-r--r--board/ti/omap5912osk/Kconfig23
-rw-r--r--board/ti/omap5912osk/MAINTAINERS6
-rw-r--r--board/ti/omap5912osk/Makefile9
-rw-r--r--board/ti/omap5912osk/config.mk30
-rw-r--r--board/ti/omap5912osk/lowlevel_init.S477
-rw-r--r--board/ti/omap5912osk/omap5912osk.c307
6 files changed, 0 insertions, 852 deletions
diff --git a/board/ti/omap5912osk/Kconfig b/board/ti/omap5912osk/Kconfig
deleted file mode 100644
index 9f7493a35f..0000000000
--- a/board/ti/omap5912osk/Kconfig
+++ /dev/null
@@ -1,23 +0,0 @@
-if TARGET_OMAP5912OSK
-
-config SYS_CPU
- string
- default "arm926ejs"
-
-config SYS_BOARD
- string
- default "omap5912osk"
-
-config SYS_VENDOR
- string
- default "ti"
-
-config SYS_SOC
- string
- default "omap"
-
-config SYS_CONFIG_NAME
- string
- default "omap5912osk"
-
-endif
diff --git a/board/ti/omap5912osk/MAINTAINERS b/board/ti/omap5912osk/MAINTAINERS
deleted file mode 100644
index 43ffb9b7b9..0000000000
--- a/board/ti/omap5912osk/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-OMAP5912OSK BOARD
-M: Rishi Bhattacharya <rishi@ti.com>
-S: Maintained
-F: board/ti/omap5912osk/
-F: include/configs/omap5912osk.h
-F: configs/omap5912osk_defconfig
diff --git a/board/ti/omap5912osk/Makefile b/board/ti/omap5912osk/Makefile
deleted file mode 100644
index d7c0ebd729..0000000000
--- a/board/ti/omap5912osk/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := omap5912osk.o
-obj-y += lowlevel_init.o
diff --git a/board/ti/omap5912osk/config.mk b/board/ti/omap5912osk/config.mk
deleted file mode 100644
index 5b8d952ba6..0000000000
--- a/board/ti/omap5912osk/config.mk
+++ /dev/null
@@ -1,30 +0,0 @@
-#
-# (C) Copyright 2002-2004
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Kshitij Gupta <Kshitij@ti.com>
-#
-# (C) Copyright 2004
-# Texas Instruments, <www.ti.com>
-# Rishi Bhattacharya <rishi@ti.com>
-#
-# TI OSK board with OMAP5912 (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# OSK has 1 bank of 32 MB SDRAM
-# Physical Address:
-# 1000'0000 to 1200'0000
-#
-#
-# Linux-Kernel is expected to be at 1000'8000, entry 1000'8000
-# (mem base + reserved)
-#
-# When running from RAM use address 1108'0000, otherwise when
-# booting from NOR flash link to address 0000'0000.
-#
-
-CONFIG_SYS_TEXT_BASE = 0x00000000
-#CONFIG_SYS_TEXT_BASE = 0x11080000
diff --git a/board/ti/omap5912osk/lowlevel_init.S b/board/ti/omap5912osk/lowlevel_init.S
deleted file mode 100644
index e05a1c7b55..0000000000
--- a/board/ti/omap5912osk/lowlevel_init.S
+++ /dev/null
@@ -1,477 +0,0 @@
-/*
- * Board specific setup info
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004
- *
- * Modified for OMAP 5912 OSK board by Rishi Bhattacharya, Apr 2004
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-#include <version.h>
-
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-.globl lowlevel_init
-lowlevel_init:
-
- /*------------------------------------------------------*
- * Ensure i-cache is enabled *
- * To configure TC regs without fetching instruction *
- *------------------------------------------------------*/
- mrc p15, 0, r0, c1, c0
- orr r0, r0, #0x1000
- mcr p15, 0, r0, c1, c0
-
- /*------------------------------------------------------*
- *mask all IRQs by setting all bits in the INTMR default*
- *------------------------------------------------------*/
- mov r1, #0xffffffff
- ldr r0, =REG_IHL1_MIR
- str r1, [r0]
- ldr r0, =REG_IHL2_MIR
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT1) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT1
- ldr r1, VAL_ARM_IDLECT1
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT2) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT2
- ldr r1, VAL_ARM_IDLECT2
- str r1, [r0]
-
- /*------------------------------------------------------*
- * Set up ARM CLM registers (IDLECT3) *
- *------------------------------------------------------*/
- ldr r0, REG_ARM_IDLECT3
- ldr r1, VAL_ARM_IDLECT3
- str r1, [r0]
-
- mov r1, #0x01 /* PER_EN bit */
- ldr r0, REG_ARM_RSTCT2
- strh r1, [r0] /* CLKM; Peripheral reset. */
-
- /* Set CLKM to Sync-Scalable */
- mov r1, #0x1000
- ldr r0, REG_ARM_SYSST
-
- mov r2, #0
-1: cmp r2, #1
- streqh r1, [r0]
- add r2, r2, #1
- cmp r2, #0x100 /* wait for any bubbles to finish */
- bne 1b
-
- ldr r1, VAL_ARM_CKCTL
- ldr r0, REG_ARM_CKCTL
- strh r1, [r0]
-
- /* a few nops to let settle */
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
- nop
-
- /* setup DPLL 1 */
- /* Ramp up the clock to 96Mhz */
- ldr r1, VAL_DPLL1_CTL
- ldr r0, REG_DPLL1_CTL
- strh r1, [r0]
- ands r1, r1, #0x10 /* Check if PLL is enabled. */
- beq lock_end /* Do not look for lock if BYPASS selected */
-2:
- ldrh r1, [r0]
- ands r1, r1, #0x01 /* Check the LOCK bit.*/
- beq 2b /* loop until bit goes hi. */
-lock_end:
-
- /*------------------------------------------------------*
- * Turn off the watchdog during init... *
- *------------------------------------------------------*/
- ldr r0, REG_WATCHDOG
- ldr r1, WATCHDOG_VAL1
- str r1, [r0]
- ldr r1, WATCHDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL1
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-
-watch1Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch1Wait
-
- ldr r0, REG_WSPRDOG
- ldr r1, WSPRDOG_VAL2
- str r1, [r0]
- ldr r0, REG_WWPSDOG
-watch2Wait:
- ldr r1, [r0]
- tst r1, #0x10
- bne watch2Wait
-
- /* Set memory timings corresponding to the new clock speed */
- ldr r3, VAL_SDRAM_CONFIG_SDF0
-
- /* Check execution location to determine current execution location
- * and branch to appropriate initialization code.
- */
- mov r0, #0x10000000 /* Load physical SDRAM base. */
- mov r1, pc /* Get current execution location. */
- cmp r1, r0 /* Compare. */
- bge skip_sdram /* Skip over EMIF-fast initialization if running from SDRAM. */
-
- /* identify the device revision, -- TMX or TMP(TMS) */
- ldr r0, REG_DEVICE_ID
- ldr r1, [r0]
-
- ldr r0, VAL_DEVICE_ID_TMP
- mov r1, r1, lsl #15
- mov r1, r1, lsr #16
- cmp r0, r1
- bne skip_TMP_Patch
-
- /* Enable TMP/TMS device new features */
- mov r0, #1
- ldr r1, REG_TC_EMIFF_DOUBLER
- str r0, [r1]
-
- /* Enable new ac parameters */
- mov r0, #0x0b
- ldr r1, REG_SDRAM_CONFIG2
- str r0, [r1]
-
- ldr r3, VAL_SDRAM_CONFIG_SDF1
-
-skip_TMP_Patch:
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r0, #0x1800 /* value should be checked */
-3:
- subs r0, r0, #0x1 /* Decrement count */
- bne 3b
-
- /*
- * Set SDRAM control values. Disable refresh before MRS command.
- */
-
- /* mobile ddr operation */
- ldr r0, REG_SDRAM_OPERATION
- mov r2, #07
- str r2, [r0]
-
- /* config register */
- ldr r0, REG_SDRAM_CONFIG
- str r3, [r0]
-
- /* manual command register */
- ldr r0, REG_SDRAM_MANUAL_CMD
-
- /* issue set cke high */
- mov r1, #CMD_SDRAM_CKE_SET_HIGH
- str r1, [r0]
-
- /* issue nop */
- mov r1, #CMD_SDRAM_NOP
- str r1, [r0]
-
- mov r2, #0x0100
-waitMDDR1:
- subs r2, r2, #1
- bne waitMDDR1 /* delay loop */
-
- /* issue precharge */
- mov r1, #CMD_SDRAM_PRECHARGE
- str r1, [r0]
-
- /* issue autorefresh x 2 */
- mov r1, #CMD_SDRAM_AUTOREFRESH
- str r1, [r0]
- str r1, [r0]
-
- /* mrs register ddr mobile */
- ldr r0, REG_SDRAM_MRS
- mov r1, #0x33
- str r1, [r0]
-
- /* emrs1 low-power register */
- ldr r0, REG_SDRAM_EMRS1
- /* self refresh on all banks */
- mov r1, #0
- str r1, [r0]
-
- ldr r0, REG_DLL_URD_CONTROL
- ldr r1, DLL_URD_CONTROL_VAL
- str r1, [r0]
-
- ldr r0, REG_DLL_LRD_CONTROL
- ldr r1, DLL_LRD_CONTROL_VAL
- str r1, [r0]
-
- ldr r0, REG_DLL_WRT_CONTROL
- ldr r1, DLL_WRT_CONTROL_VAL
- str r1, [r0]
-
- /* delay loop */
- mov r0, #0x0100
-waitMDDR2:
- subs r0, r0, #1
- bne waitMDDR2
-
- /*
- * Delay for SDRAM initialization.
- */
- mov r0, #0x1800
-4:
- subs r0, r0, #1 /* Decrement count. */
- bne 4b
- b common_tc
-
-skip_sdram:
- ldr r0, REG_SDRAM_CONFIG
- str r3, [r0]
-
-common_tc:
- /* slow interface */
- ldr r1, VAL_TC_EMIFS_CS0_CONFIG
- ldr r0, REG_TC_EMIFS_CS0_CONFIG
- str r1, [r0] /* Chip Select 0 */
-
- ldr r1, VAL_TC_EMIFS_CS1_CONFIG
- ldr r0, REG_TC_EMIFS_CS1_CONFIG
- str r1, [r0] /* Chip Select 1 */
-
- ldr r1, VAL_TC_EMIFS_CS3_CONFIG
- ldr r0, REG_TC_EMIFS_CS3_CONFIG
- str r1, [r0] /* Chip Select 3 */
-
- ldr r1, VAL_TC_EMIFS_DWS
- ldr r0, REG_TC_EMIFS_DWS
- str r1, [r0] /* Enable EMIFS.RDY for CS1 (ether) */
-
-#ifdef CONFIG_H2_OMAP1610
- /* inserting additional 2 clock cycle hold time for LAN */
- ldr r0, REG_TC_EMIFS_CS1_ADVANCED
- ldr r1, VAL_TC_EMIFS_CS1_ADVANCED
- str r1, [r0]
-#endif
- /* Start MPU Timer 1 */
- ldr r0, REG_MPU_LOAD_TIMER
- ldr r1, VAL_MPU_LOAD_TIMER
- str r1, [r0]
-
- ldr r0, REG_MPU_CNTL_TIMER
- ldr r1, VAL_MPU_CNTL_TIMER
- str r1, [r0]
-
- /*
- * Setup a temporary stack
- */
- ldr sp, SRAM_STACK
- bic sp, sp, #7 /* 8-byte alignment for ABI compliance */
-
- /*
- * Save the old lr(passed in ip) and the current lr to stack
- */
- push {ip, lr}
-
- /*
- * go setup pll, mux, memory
- */
- bl s_init
- pop {ip, pc}
-
- /* back to arch calling code */
- mov pc, lr
-
- /* the literal pools origin */
- .ltorg
-
-REG_DEVICE_ID: /* 32 bits */
- .word 0xfffe2004
-REG_TC_EMIFS_CONFIG:
- .word 0xfffecc0c
-REG_TC_EMIFS_CS0_CONFIG: /* 32 bits */
- .word 0xfffecc10
-REG_TC_EMIFS_CS1_CONFIG: /* 32 bits */
- .word 0xfffecc14
-REG_TC_EMIFS_CS2_CONFIG: /* 32 bits */
- .word 0xfffecc18
-REG_TC_EMIFS_CS3_CONFIG: /* 32 bits */
- .word 0xfffecc1c
-REG_TC_EMIFS_DWS: /* 32 bits */
- .word 0xfffecc40
-#ifdef CONFIG_H2_OMAP1610
-REG_TC_EMIFS_CS1_ADVANCED: /* 32 bits */
- .word 0xfffecc54
-#endif
-
-/* MPU clock/reset/power mode control registers */
-REG_ARM_CKCTL: /* 16 bits */
- .word 0xfffece00
-REG_ARM_IDLECT3: /* 16 bits */
- .word 0xfffece24
-REG_ARM_IDLECT2: /* 16 bits */
- .word 0xfffece08
-REG_ARM_IDLECT1: /* 16 bits */
- .word 0xfffece04
-REG_ARM_RSTCT2: /* 16 bits */
- .word 0xfffece14
-REG_ARM_SYSST: /* 16 bits */
- .word 0xfffece18
-
-/* DPLL control registers */
-REG_DPLL1_CTL: /* 16 bits */
- .word 0xfffecf00
-
-/* Watch Dog register */
-/* secure watchdog stop */
-REG_WSPRDOG:
- .word 0xfffeb048
-/* watchdog write pending */
-REG_WWPSDOG:
- .word 0xfffeb034
-
-WSPRDOG_VAL1:
- .word 0x0000aaaa
-WSPRDOG_VAL2:
- .word 0x00005555
-
-/* SDRAM config is: auto refresh enabled, 16 bit 4 bank,
- counter @8192 rows, 10 ns, 8 burst */
-REG_SDRAM_CONFIG:
- .word 0xfffecc20
-REG_SDRAM_CONFIG2:
- .word 0xfffecc3c
-REG_TC_EMIFF_DOUBLER: /* 32 bits */
- .word 0xfffecc60
-
-/* Operation register */
-REG_SDRAM_OPERATION:
- .word 0xfffecc80
-
-/* Manual command register */
-REG_SDRAM_MANUAL_CMD:
- .word 0xfffecc84
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_MRS:
- .word 0xfffecc70
-
-/* SDRAM MRS (New) config is: CAS latency is 2, burst length 8 */
-REG_SDRAM_EMRS1:
- .word 0xfffecc78
-
-/* WRT DLL register */
-REG_DLL_WRT_CONTROL:
- .word 0xfffecc68
-DLL_WRT_CONTROL_VAL:
- .word 0x03f00002 /* Phase of 72deg, write offset +31 */
-
-/* URD DLL register */
-REG_DLL_URD_CONTROL:
- .word 0xfffeccc0
-DLL_URD_CONTROL_VAL:
- .word 0x00800002 /* Phase of 72deg, read offset +31 */
-
-/* LRD DLL register */
-REG_DLL_LRD_CONTROL:
- .word 0xfffecccc
-DLL_LRD_CONTROL_VAL:
- .word 0x00800002 /* read offset +31 */
-
-REG_WATCHDOG:
- .word 0xfffec808
-WATCHDOG_VAL1:
- .word 0x000000f5
-WATCHDOG_VAL2:
- .word 0x000000a0
-
-REG_MPU_LOAD_TIMER:
- .word 0xfffec504
-REG_MPU_CNTL_TIMER:
- .word 0xfffec500
-VAL_MPU_LOAD_TIMER:
- .word 0xffffffff
-VAL_MPU_CNTL_TIMER:
- .word 0xffffffa1
-
-/* 96 MHz Samsung Mobile DDR */
-/* Original setting for TMX device */
-VAL_SDRAM_CONFIG_SDF0:
- .word 0x0014e6fe
-
-/* NEW_SYS_FREQ mode (valid only TMP/TMS devices) */
-VAL_SDRAM_CONFIG_SDF1:
- .word 0x0114e6fe
-
-VAL_ARM_CKCTL:
- .word 0x2000 /* was: 0x3000, now use CLK_REF for timer input */
-VAL_DPLL1_CTL:
- .word 0x2830
-
-#ifdef CONFIG_OSK_OMAP5912
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x002130b0
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x00001133
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0x000055f0
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x88013141
-VAL_TC_EMIFS_DWS: /* Enable EMIFS.RDY for CS1 access (ether) */
- .word 0x000000c0
-VAL_DEVICE_ID_TMP: /* TMP/TMS=0xb65f, TMX=0xb58c */
- .word 0xb65f
-#endif
-
-#ifdef CONFIG_H2_OMAP1610
-VAL_TC_EMIFS_CS0_CONFIG:
- .word 0x00203331
-VAL_TC_EMIFS_CS1_CONFIG:
- .word 0x8180fff3
-VAL_TC_EMIFS_CS2_CONFIG:
- .word 0xf800f22a
-VAL_TC_EMIFS_CS3_CONFIG:
- .word 0x88013141
-VAL_TC_EMIFS_CS1_ADVANCED:
- .word 0x00000022
-#endif
-
-VAL_ARM_IDLECT1:
- .word 0x00000400
-VAL_ARM_IDLECT2:
- .word 0x00000886
-VAL_ARM_IDLECT3:
- .word 0x00000015
-
-SRAM_STACK:
- .word CONFIG_SYS_INIT_SP_ADDR
-
-/* command values */
-.equ CMD_SDRAM_NOP, 0x00000000
-.equ CMD_SDRAM_PRECHARGE, 0x00000001
-.equ CMD_SDRAM_AUTOREFRESH, 0x00000002
-.equ CMD_SDRAM_CKE_SET_HIGH, 0x00000007
diff --git a/board/ti/omap5912osk/omap5912osk.c b/board/ti/omap5912osk/omap5912osk.c
deleted file mode 100644
index 88a7310cec..0000000000
--- a/board/ti/omap5912osk/omap5912osk.c
+++ /dev/null
@@ -1,307 +0,0 @@
-/*
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * (C) Copyright 2002
- * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
- *
- * (C) Copyright 2003
- * Texas Instruments, <www.ti.com>
- * Kshitij Gupta <Kshitij@ti.com>
- *
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
- * Rishi Bhattacharya <rishi@ti.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#if defined(CONFIG_OMAP1610)
-#include <./configs/omap1510.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void flash__init (void);
-void ether__init (void);
-void set_muxconf_regs (void);
-void peripheral_power_enable (void);
-
-#define COMP_MODE_ENABLE ((unsigned int)0x0000EAEF)
-
-static inline void delay (unsigned long loops)
-{
- __asm__ volatile ("1:\n"
- "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0" (loops));
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-
-int board_init (void)
-{
- gd->bd->bi_arch_number = MACH_TYPE_OMAP_OSK;
-
- /* adress of boot parameters */
- gd->bd->bi_boot_params = 0x10000100;
-
- flash__init();
- ether__init();
-
- return 0;
-}
-
-void s_init(void)
-{
- /* Configure MUX settings */
- set_muxconf_regs ();
- peripheral_power_enable ();
-
-/* this speeds up your boot a quite a bit. However to make it
- * work, you need make sure your kernel startup flush bug is fixed.
- * ... rkw ...
- */
- icache_enable ();
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-void flash__init (void)
-{
-#define EMIFS_GlB_Config_REG 0xfffecc0c
- unsigned int regval;
- regval = *((volatile unsigned int *) EMIFS_GlB_Config_REG);
- /* Turn off write protection for flash devices. */
- regval = regval | 0x0001;
- *((volatile unsigned int *) EMIFS_GlB_Config_REG) = regval;
-}
-/*************************************************************
- Routine:ether__init
- Description: take the Ethernet controller out of reset and wait
- for the EEPROM load to complete.
-*************************************************************/
-void ether__init (void)
-{
-#define ETH_CONTROL_REG 0x0480000b
- int i;
-
- *((volatile unsigned short *) 0xfffece08) = 0x03FF;
- *((volatile unsigned short *) 0xfffb3824) = 0x8000;
- *((volatile unsigned short *) 0xfffb3830) = 0x0000;
- *((volatile unsigned short *) 0xfffb3834) = 0x0009;
- *((volatile unsigned short *) 0xfffb3838) = 0x0009;
- *((volatile unsigned short *) 0xfffb3818) = 0x0002;
- *((volatile unsigned short *) 0xfffb382C) = 0x0048;
- *((volatile unsigned short *) 0xfffb3824) = 0x8603;
- udelay (3);
- for (i=0;i<2000;i++);
- *((volatile unsigned short *) 0xfffb381C) = 0x6610;
- udelay (30);
- for (i=0;i<10000;i++);
-
- *((volatile unsigned char *) ETH_CONTROL_REG) &= ~0x01;
- udelay (3);
-
-
-}
-
-/******************************
- Routine:
- Description:
-******************************/
-int dram_init(void)
-{
- gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
-
- return 0;
-}
-
-void dram_init_banksize(void)
-{
- gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-}
-
-/******************************************************
- Routine: set_muxconf_regs
- Description: Setting up the configuration Mux registers
- specific to the hardware
-*******************************************************/
-void set_muxconf_regs (void)
-{
- volatile unsigned int *MuxConfReg;
- /* set each registers to its reset value; */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
- /* setup for UART1 */
- *MuxConfReg &= ~(0x02000000); /* bit 25 */
- /* setup for UART2 */
- *MuxConfReg &= ~(0x01000000); /* bit 24 */
- /* Disable Uwire CS Hi-Z */
- *MuxConfReg |= 0x08000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_4);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_5);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_6);
- /*setup mux for UART3 */
- *MuxConfReg |= 0x00000001; /* bit3, 1, 0 (mux0 5,5,26) */
- *MuxConfReg &= ~0x0000003e;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_7);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_8);
- /* Disable Uwire CS Hi-Z */
- *MuxConfReg |= 0x00001200; /*bit 9 for CS0 12 for CS3 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_9);
- /* Need to turn on bits 21 and 12 in FUNC_MUX_CTRL_9 so the */
- /* hardware will actually use TX and RTS based on bit 25 in */
- /* FUNC_MUX_CTRL_0. I told you this thing was screwy! */
- *MuxConfReg |= 0x00201000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_A);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_B);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_C);
- /* setup for UART2 */
- /* Need to turn on bits 27 and 24 in FUNC_MUX_CTRL_C so the */
- /* hardware will actually use TX and RTS based on bit 24 in */
- /* FUNC_MUX_CTRL_0. */
- *MuxConfReg |= 0x09000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_D);
- *MuxConfReg |= 0x00000020;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_0);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_1);
- *MuxConfReg = 0x00000000;
- /* mux setup for SD/MMC driver */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_2);
- *MuxConfReg &= 0xFFFE0FFF;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- /* bit 13 for MMC2 XOR_CLK */
- *MuxConfReg &= ~(0x00002000);
- /* bit 29 for UART 1 */
- *MuxConfReg &= ~(0x00002000);
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) FUNC_MUX_CTRL_0);
- /* Configure for USB. Turn on VBUS_CTRL and VBUS_MODE. */
- *MuxConfReg |= 0x000C0000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int)USB_TRANSCEIVER_CTRL);
- *MuxConfReg &= ~(0x00000070);
- *MuxConfReg &= ~(0x00000008);
- *MuxConfReg |= 0x00000003;
- *MuxConfReg |= 0x00000180;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- /* bit 17, software controls VBUS */
- *MuxConfReg &= ~(0x00020000);
- /* Enable USB 48 and 12M clocks */
- *MuxConfReg |= 0x00000200;
- *MuxConfReg &= ~(0x00000180);
- /*2.75V for MMCSDIO1 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) VOLTAGE_CTRL_0);
- *MuxConfReg = 0x00001FE7;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_0);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_1);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_3);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_4);
- *MuxConfReg = 0x00000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PULL_DWN_CTRL_4);
- *MuxConfReg = 0x00000000;
- /* Turn on UART2 48 MHZ clock */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) MOD_CONF_CTRL_0);
- *MuxConfReg |= 0x40000000;
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) USB_OTG_CTRL);
- /* setup for USB VBus detection OMAP161x */
- *MuxConfReg |= 0x00040000; /* bit 18 */
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int) PU_PD_SEL_2);
- /* PullUps for SD/MMC driver */
- *MuxConfReg |= ~(0xFFFE0FFF);
- MuxConfReg =
- (volatile unsigned int *) ((unsigned int)COMP_MODE_CTRL_0);
- *MuxConfReg = COMP_MODE_ENABLE;
-}
-
-/******************************************************
- Routine: peripheral_power_enable
- Description: Enable the power for UART1
-*******************************************************/
-void peripheral_power_enable (void)
-{
-#define UART1_48MHZ_ENABLE ((unsigned short)0x0200)
-#define SW_CLOCK_REQUEST ((volatile unsigned short *)0xFFFE0834)
-
- *SW_CLOCK_REQUEST |= UART1_48MHZ_ENABLE;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
- char buf[64];
- int i = getenv_f("serial#", buf, sizeof(buf));
-
- puts("Board: OSK5912");
-
- if (i > 0) {
- puts(", serial# ");
- puts(buf);
- }
- putc('\n');
-
- return (0);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_LAN91C96
- rc = lan91c96_initialize(0, CONFIG_LAN91C96_BASE);
-#endif
- return rc;
-}
-#endif
generated by cgit (git 2.34.1) at 2024-12-25 06:45:55 +0000