diff options
Diffstat (limited to 'board')
40 files changed, 2311 insertions, 186 deletions
diff --git a/board/amcc/acadia/acadia.c b/board/amcc/acadia/acadia.c index baf598c677..3b63c8a741 100644 --- a/board/amcc/acadia/acadia.c +++ b/board/amcc/acadia/acadia.c @@ -62,6 +62,10 @@ int board_early_init_f(void) acadia_gpio_init(); + /* Configure 405EZ for NAND usage */ + mtsdr(sdrnand0, 0x80c00000); + mtsdr(sdrultra0, 0x8d110000); + /* USB Host core needs this bit set */ mfsdr(sdrultra1, reg); mtsdr(sdrultra1, reg | SDR_ULTRA1_LEDNENABLE); @@ -91,8 +95,11 @@ int misc_init_f(void) int checkboard(void) { char *s = getenv("serial#"); + u8 rev; + + rev = in8(CFG_CPLD_BASE + 0); + printf("Board: Acadia - AMCC PPC405EZ Evaluation Board, Rev. %X", rev); - printf("Board: Acadia - AMCC PPC405EZ Evaluation Board"); if (s != NULL) { puts(", serial# "); puts(s); diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c index b5bb145808..6260b016df 100644 --- a/board/amcc/bamboo/bamboo.c +++ b/board/amcc/bamboo/bamboo.c @@ -277,87 +277,6 @@ int board_early_init_f(void) return 0; } -#if (CONFIG_COMMANDS & CFG_CMD_NAND) -#include <linux/mtd/nand_legacy.h> -extern struct nand_chip nand_dev_desc[CFG_MAX_NAND_DEVICE]; - -/*----------------------------------------------------------------------------+ - | nand_reset. - | Reset Nand flash - | This routine will abort previous cmd - +----------------------------------------------------------------------------*/ -int nand_reset(ulong addr) -{ - int wait=0, stat=0; - - out8(addr + NAND_CMD_REG, NAND0_CMD_RESET); - out8(addr + NAND_CMD_REG, NAND0_CMD_READ_STATUS); - - while ((stat != 0xc0) && (wait != 0xffff)) { - stat = in8(addr + NAND_DATA_REG); - wait++; - } - - if (stat == 0xc0) { - return 0; - } else { - printf("NAND Reset timeout.\n"); - return -1; - } -} - -void board_nand_set_device(int cs, ulong addr) -{ - /* Set NandFlash Core Configuration Register */ - out32(addr + NAND_CCR_REG, 0x00001000 | (cs << 24)); - - switch (cs) { - case 1: - /* ------- - * NAND0 - * ------- - * K9F1208U0A : 4 addr cyc, 1 col + 3 Row - * Set NDF1CR - Enable External CS1 in NAND FLASH controller - */ - out32(addr + NAND_CR1_REG, 0x80002222); - break; - - case 2: - /* ------- - * NAND1 - * ------- - * K9K2G0B : 5 addr cyc, 2 col + 3 Row - * Set NDF2CR : Enable External CS2 in NAND FLASH controller - */ - out32(addr + NAND_CR2_REG, 0xC0007777); - break; - } - - /* Perform Reset Command */ - if (nand_reset(addr) != 0) - return; -} - -void nand_init(void) -{ - board_nand_set_device(1, CFG_NAND_ADDR); - - nand_probe(CFG_NAND_ADDR); - if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) { - print_size(nand_dev_desc[0].totlen, "\n"); - } - -#if 0 /* NAND1 not supported yet */ - board_nand_set_device(2, CFG_NAND2_ADDR); - - nand_probe(CFG_NAND2_ADDR); - if (nand_dev_desc[0].ChipID != NAND_ChipID_UNKNOWN) { - print_size(nand_dev_desc[0].totlen, "\n"); - } -#endif -} -#endif /* (CONFIG_COMMANDS & CFG_CMD_NAND) */ - int checkboard(void) { char *s = getenv("serial#"); diff --git a/board/amcc/bamboo/u-boot.lds b/board/amcc/bamboo/u-boot.lds index 176900ec2f..f6d7183199 100644 --- a/board/amcc/bamboo/u-boot.lds +++ b/board/amcc/bamboo/u-boot.lds @@ -68,19 +68,7 @@ SECTIONS cpu/ppc4xx/start.o (.text) board/amcc/bamboo/init.o (.text) - cpu/ppc4xx/kgdb.o (.text) - cpu/ppc4xx/traps.o (.text) - cpu/ppc4xx/interrupts.o (.text) - cpu/ppc4xx/serial.o (.text) - cpu/ppc4xx/cpu_init.o (.text) - cpu/ppc4xx/speed.o (.text) - common/dlmalloc.o (.text) - lib_generic/crc32.o (.text) - lib_ppc/extable.o (.text) - lib_generic/zlib.o (.text) - -/* . = env_offset;*/ -/* common/environment.o(.text)*/ + board/amcc/bamboo/bamboo.o (.text) *(.text) *(.fixup) diff --git a/board/amcc/sequoia/sdram.c b/board/amcc/sequoia/sdram.c index f8b837ed28..d045df1872 100644 --- a/board/amcc/sequoia/sdram.c +++ b/board/amcc/sequoia/sdram.c @@ -371,6 +371,14 @@ void denali_core_search_data_eye(unsigned long memory_size) } #endif /* CONFIG_DDR_DATA_EYE */ +#if defined(CONFIG_NAND_SPL) +/* Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big + * for the 4k NAND boot image so define bus_frequency to 133MHz here + * which is save for the refresh counter setup. + */ +#define get_bus_freq(val) 133000000 +#endif + /************************************************************************* * * initdram -- 440EPx's DDR controller is a DENALI Core @@ -404,7 +412,7 @@ long int initdram (int board_type) mtsdram(DDR0_22, 0x00267F0B); mtsdram(DDR0_23, 0x00000000); mtsdram(DDR0_24, 0x01010002); - if (speed > 133333333) + if (speed > 133333334) mtsdram(DDR0_26, 0x5B26050C); else mtsdram(DDR0_26, 0x5B260408); diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c index 930fa71cb9..870401458e 100644 --- a/board/amcc/sequoia/sequoia.c +++ b/board/amcc/sequoia/sequoia.c @@ -132,6 +132,12 @@ int board_early_init_f(void) (0x80000000 >> (28 + CFG_NAND_CS)); mtsdr(SDR0_CUST0, sdr0_cust0); + /* Update EBC speed after booting from i2c bootstrap settings + * on newer boards with 33.333 MHZ Clocks + */ + if (in8(CFG_BCSR_BASE + 3) & 0x80) + mtcpr(0xe0, 0x02000000); + return 0; } @@ -363,8 +369,8 @@ int checkboard(void) printf("Board: Rainier - AMCC PPC440GRx Evaluation Board"); #endif - rev = *(u8 *)(CFG_BCSR_BASE + 0); - val = *(u8 *)(CFG_BCSR_BASE + 5) & 0x01; + rev = in8(CFG_BCSR_BASE + 0); + val = in8(CFG_BCSR_BASE + 5) & 0x01; printf(", Rev. %X, PCI=%d MHz", rev, val ? 66 : 33); if (s != NULL) { diff --git a/board/cds/mpc8541cds/mpc8541cds.c b/board/cds/mpc8541cds/mpc8541cds.c index a42904cf73..4192324836 100644 --- a/board/cds/mpc8541cds/mpc8541cds.c +++ b/board/cds/mpc8541cds/mpc8541cds.c @@ -477,11 +477,14 @@ void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_ta static struct pci_config_table pci_mpc85xxcds_config_table[] = { {0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}}, {0x1106, 0x0686, PCI_ANY_ID, 1, 2, 0, mpc85xx_config_via, {0,0,0}}, - {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, mpc85xx_config_via_usbide, {0,0,0}}, + {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, + mpc85xx_config_via_usbide, {0,0,0}}, {0x1105, 0x3038, PCI_ANY_ID, 1, 2, 2, mpc85xx_config_via_usb, {0,0,0}}, {0x1106, 0x3038, PCI_ANY_ID, 1, 2, 3, mpc85xx_config_via_usb2, {0,0,0}}, - {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, mpc85xx_config_via_power, {0,0,0}}, - {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}} + {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, + mpc85xx_config_via_power, {0,0,0}}, + {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}}, + {}, }; static struct pci_controller hose[] = { diff --git a/board/cds/mpc8541cds/u-boot.lds b/board/cds/mpc8541cds/u-boot.lds index 1bea0074fa..dc87a122a1 100644 --- a/board/cds/mpc8541cds/u-boot.lds +++ b/board/cds/mpc8541cds/u-boot.lds @@ -69,6 +69,7 @@ SECTIONS cpu/mpc85xx/interrupts.o (.text) cpu/mpc85xx/cpu_init.o (.text) cpu/mpc85xx/cpu.o (.text) + drivers/tsec.o (.text) cpu/mpc85xx/speed.o (.text) cpu/mpc85xx/pci.o (.text) common/dlmalloc.o (.text) diff --git a/board/cds/mpc8548cds/init.S b/board/cds/mpc8548cds/init.S index 978bda5e4d..d468f5b618 100644 --- a/board/cds/mpc8548cds/init.S +++ b/board/cds/mpc8548cds/init.S @@ -64,8 +64,9 @@ tlb1_entry: /* * Number of TLB0 and TLB1 entries in the following table */ - .long 13 + .long (2f-1f)/16 +1: #if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR) /* * TLB0 4K Non-cacheable, guarded @@ -134,7 +135,7 @@ tlb1_entry: /* * TLB 1: 256M Non-cacheable, guarded - * 0x80000000 256M PCI1 MEM First half + * 0x80000000 256M PCI1 MEM */ .long TLB1_MAS0(1, 1, 0) .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) @@ -143,40 +144,37 @@ tlb1_entry: /* * TLB 2: 256M Non-cacheable, guarded - * 0x90000000 256M PCI1 MEM Second half + * 0x90000000 256M PCI2 MEM */ .long TLB1_MAS0(1, 2, 0) .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000), + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000), + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) /* - * TLB 3: 256M Non-cacheable, guarded - * 0xa0000000 256M PCI2 MEM First half + * TLB 3: 1GB Non-cacheable, guarded + * 0xa0000000 256M PEX MEM First half + * 0xb0000000 256M PEX MEM Second half + * 0xc0000000 256M Rapid IO MEM First half + * 0xd0000000 256M Rapid IO MEM Second half */ .long TLB1_MAS0(1, 3, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE), 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PEX_MEM_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PEX_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) /* - * TLB 4: 256M Non-cacheable, guarded - * 0xb0000000 256M PCI2 MEM Second half + * TLB 4: Reserved for future usage */ - .long TLB1_MAS0(1, 4, 0) - .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) - .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI2_MEM_BASE + 0x10000000), - 0,0,0,0,1,0,1,0) - .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI2_MEM_BASE + 0x10000000), - 0,0,0,0,0,1,0,1,0,1) /* * TLB 5: 64M Non-cacheable, guarded * 0xe000_0000 1M CCSRBAR - * 0xe200_0000 16M PCI1 IO - * 0xe300_0000 16M PCI2 IO + * 0xe200_0000 8M PCI1 IO + * 0xe280_0000 8M PCI2 IO + * 0xe300_0000 16M PEX IO */ .long TLB1_MAS0(1, 5, 0) .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) @@ -200,19 +198,22 @@ tlb1_entry: .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1M) .long TLB1_MAS2(E500_TLB_EPN(CADMUS_BASE_ADDR), 0,0,0,0,1,0,1,0) .long TLB1_MAS3(E500_TLB_RPN(CADMUS_BASE_ADDR), 0,0,0,0,0,1,0,1,0,1) - +2: entry_end /* * LAW(Local Access Window) configuration: * * 0x0000_0000 0x7fff_ffff DDR 2G - * 0x8000_0000 0x9fff_ffff PCI1 MEM 512M - * 0xa000_0000 0xbfff_ffff PCI2 MEM 512M + * 0x8000_0000 0x8fff_ffff PCI1 MEM 256M + * 0x9000_0000 0x9fff_ffff PCI2 MEM 256M + * 0xa000_0000 0xbfff_ffff PEX MEM 512M + * 0xc000_0000 0xdfff_ffff RapidIO 512M * 0xe000_0000 0xe000_ffff CCSR 1M - * 0xe200_0000 0xe20f_ffff PCI1 IO 1M - * 0xe210_0000 0xe21f_ffff PCI2 IO 1M - * 0xf000_0000 0xf7ff_ffff SDRAM 128M + * 0xe200_0000 0xe27f_ffff PCI1 IO 8M + * 0xe280_0000 0xe2ff_ffff PCI2 IO 8M + * 0xe300_0000 0xe3ff_ffff PEX IO 16M + * 0xf000_0000 0xf3ff_ffff SDRAM 64M * 0xf800_0000 0xf80f_ffff NVRAM/CADMUS (*) 1M * 0xff00_0000 0xff7f_ffff FLASH (2nd bank) 8M * 0xff80_0000 0xffff_ffff FLASH (boot bank) 8M @@ -229,27 +230,39 @@ tlb1_entry: #define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN) #define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff) -#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M)) +#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_256M)) #define LAWBAR2 ((CFG_PCI2_MEM_BASE>>12) & 0xfffff) -#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M)) +#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_256M)) #define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff) -#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_1M)) +#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_8M)) #define LAWBAR4 ((CFG_PCI2_IO_PHYS>>12) & 0xfffff) -#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_1M)) +#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_8M)) /* LBC window - maps 256M 0xf0000000 -> 0xffffffff */ #define LAWBAR5 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff) #define LAWAR5 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M)) +#define LAWBAR6 ((CFG_PEX_MEM_BASE>>12) & 0xfffff) +#define LAWAR6 (LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_512M)) + +#define LAWBAR7 ((CFG_PEX_IO_PHYS>>12) & 0xfffff) +#define LAWAR7 (LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_16M)) + +#define LAWBAR8 ((CFG_RIO_MEM_BASE>>12) & 0xfffff) +#define LAWAR8 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M)) + .section .bootpg, "ax" .globl law_entry law_entry: entry_start - .long 6 + .long (4f-3f)/8 +3: .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3 - .long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5 + .long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5,LAWBAR6,LAWAR6,LAWBAR7,LAWAR7 + .long LAWBAR8,LAWAR8 +4: entry_end diff --git a/board/cds/mpc8548cds/mpc8548cds.c b/board/cds/mpc8548cds/mpc8548cds.c index 7433ebf25b..929ff2e662 100644 --- a/board/cds/mpc8548cds/mpc8548cds.c +++ b/board/cds/mpc8548cds/mpc8548cds.c @@ -51,6 +51,7 @@ int checkboard (void) { volatile immap_t *immap = (immap_t *) CFG_CCSRBAR; volatile ccsr_gur_t *gur = &immap->im_gur; + volatile ccsr_local_ecm_t *ecm = &immap->im_local_ecm; /* PCI slot in USER bits CSR[6:7] by convention. */ uint pci_slot = get_pci_slot (); @@ -89,6 +90,12 @@ int checkboard (void) */ local_bus_init (); + /* + * Fix CPU2 errata: A core hang possible while executing a + * msync instruction and a snoopable transaction from an I/O + * master tagged to make quick forward progress is present. + */ + ecm->eebpcr |= (1 << 16); /* * Hack TSEC 3 and 4 IO voltages. @@ -303,11 +310,14 @@ void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_ta static struct pci_config_table pci_mpc85xxcds_config_table[] = { {0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}}, {0x1106, 0x0686, PCI_ANY_ID, 1, 2, 0, mpc85xx_config_via, {0,0,0}}, - {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, mpc85xx_config_via_usbide, {0,0,0}}, + {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, + mpc85xx_config_via_usbide, {0,0,0}}, {0x1105, 0x3038, PCI_ANY_ID, 1, 2, 2, mpc85xx_config_via_usb, {0,0,0}}, {0x1106, 0x3038, PCI_ANY_ID, 1, 2, 3, mpc85xx_config_via_usb2, {0,0,0}}, - {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, mpc85xx_config_via_power, {0,0,0}}, - {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}} + {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, + mpc85xx_config_via_power, {0,0,0}}, + {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}}, + {}, }; static struct pci_controller hose[] = { diff --git a/board/cds/mpc8548cds/u-boot.lds b/board/cds/mpc8548cds/u-boot.lds index 2c8fe9603d..c1f3495d75 100644 --- a/board/cds/mpc8548cds/u-boot.lds +++ b/board/cds/mpc8548cds/u-boot.lds @@ -69,6 +69,7 @@ SECTIONS cpu/mpc85xx/interrupts.o (.text) cpu/mpc85xx/cpu_init.o (.text) cpu/mpc85xx/cpu.o (.text) + drivers/tsec.o (.text) cpu/mpc85xx/speed.o (.text) cpu/mpc85xx/pci.o (.text) common/dlmalloc.o (.text) diff --git a/board/cds/mpc8555cds/mpc8555cds.c b/board/cds/mpc8555cds/mpc8555cds.c index d980ea6310..704bf03164 100644 --- a/board/cds/mpc8555cds/mpc8555cds.c +++ b/board/cds/mpc8555cds/mpc8555cds.c @@ -474,11 +474,14 @@ void dummy_func(struct pci_controller* hose, pci_dev_t dev, struct pci_config_ta static struct pci_config_table pci_mpc85xxcds_config_table[] = { {0x10e3, 0x0513, PCI_ANY_ID, 1, 3, PCI_ANY_ID, dummy_func, {0,0,0}}, {0x1106, 0x0686, PCI_ANY_ID, 1, 2, 0, mpc85xx_config_via, {0,0,0}}, - {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, mpc85xx_config_via_usbide, {0,0,0}}, + {0x1106, 0x0571, PCI_ANY_ID, 1, 2, 1, + mpc85xx_config_via_usbide, {0,0,0}}, {0x1105, 0x3038, PCI_ANY_ID, 1, 2, 2, mpc85xx_config_via_usb, {0,0,0}}, {0x1106, 0x3038, PCI_ANY_ID, 1, 2, 3, mpc85xx_config_via_usb2, {0,0,0}}, - {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, mpc85xx_config_via_power, {0,0,0}}, - {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}} + {0x1106, 0x3058, PCI_ANY_ID, 1, 2, 5, + mpc85xx_config_via_power, {0,0,0}}, + {0x1106, 0x3068, PCI_ANY_ID, 1, 2, 6, mpc85xx_config_via_ac97, {0,0,0}}, + {}, }; @@ -487,7 +490,7 @@ static struct pci_controller hose[] = { config_table: pci_mpc85xxcds_config_table, }, #ifdef CONFIG_MPC85XX_PCI2 - { } + {}, #endif }; diff --git a/board/cds/mpc8555cds/u-boot.lds b/board/cds/mpc8555cds/u-boot.lds index 2aa2ad78fc..9285928dc4 100644 --- a/board/cds/mpc8555cds/u-boot.lds +++ b/board/cds/mpc8555cds/u-boot.lds @@ -69,6 +69,7 @@ SECTIONS cpu/mpc85xx/interrupts.o (.text) cpu/mpc85xx/cpu_init.o (.text) cpu/mpc85xx/cpu.o (.text) + drivers/tsec.o (.text) cpu/mpc85xx/speed.o (.text) cpu/mpc85xx/pci.o (.text) common/dlmalloc.o (.text) diff --git a/board/freescale/mpc8544ds/Makefile b/board/freescale/mpc8544ds/Makefile new file mode 100644 index 0000000000..bec2168639 --- /dev/null +++ b/board/freescale/mpc8544ds/Makefile @@ -0,0 +1,58 @@ +# +# Copyright 2007 Freescale Semiconductor, Inc. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +# ifneq ($(OBJTREE),$(SRCTREE)) +# $(shell mkdir -p $(obj)./common) +# endif + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o \ + ../common/pixis.o + +SOBJS := init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) crv $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/freescale/mpc8544ds/config.mk b/board/freescale/mpc8544ds/config.mk new file mode 100644 index 0000000000..85663ef02b --- /dev/null +++ b/board/freescale/mpc8544ds/config.mk @@ -0,0 +1,32 @@ +# +# Copyright 2007 Freescale Semiconductor, Inc. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# mpc8544ds board +# +ifndef TEXT_BASE +TEXT_BASE = 0xfff80000 +endif + +PLATFORM_CPPFLAGS += -DCONFIG_E500=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC8544=1 diff --git a/board/freescale/mpc8544ds/init.S b/board/freescale/mpc8544ds/init.S new file mode 100644 index 0000000000..296fee5e60 --- /dev/null +++ b/board/freescale/mpc8544ds/init.S @@ -0,0 +1,243 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <ppc_asm.tmpl> +#include <ppc_defs.h> +#include <asm/cache.h> +#include <asm/mmu.h> +#include <config.h> +#include <mpc85xx.h> + +#define LAWAR_TRGT_PCI1 0x00000000 +#define LAWAR_TRGT_PCIE1 0x00200000 +#define LAWAR_TRGT_PCIE2 0x00100000 +#define LAWAR_TRGT_PCIE3 0x00300000 +#define LAWAR_TRGT_LBC 0x00400000 +#define LAWAR_TRGT_DDR 0x00f00000 + +/* + * TLB0 and TLB1 Entries + * + * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR. + * However, CCSRBAR is then relocated to CFG_CCSRBAR right after + * these TLB entries are established. + * + * The TLB entries for DDR are dynamically setup in spd_sdram() + * and use TLB1 Entries 8 through 15 as needed according to the + * size of DDR memory. + * + * MAS0: tlbsel, esel, nv + * MAS1: valid, iprot, tid, ts, tsize + * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr + */ + +#define entry_start \ + mflr r1 ; \ + bl 0f ; + +#define entry_end \ +0: mflr r0 ; \ + mtlr r1 ; \ + blr ; + + + .section .bootpg, "ax" + .globl tlb1_entry +tlb1_entry: + entry_start + + /* + * Number of TLB0 and TLB1 entries in the following table + */ + .long (2f-1f)/16 +1: + /* + * TLB0 4K Non-cacheable, guarded + * 0xff700000 4K Initial CCSRBAR mapping + * + * This ends up at a TLB0 Index==0 entry, and must not collide + * with other TLB0 Entries. + */ + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB0 16K Cacheable, guarded + * Temporary Global data for initialization + * + * Use four 4K TLB0 entries. These entries must be cacheable + * as they provide the bootstrap memory before the memory + * controler and real memory have been configured. + * + * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, + * and must not collide with other TLB0 entries. + */ + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), + 0,0,0,0,0,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), + 0,0,0,0,0,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), + 0,0,0,0,0,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), + 0,0,0,0,0,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + + /* + * TLB 0: 64M Non-cacheable, guarded + * 0xfc000000 64M Covers FLASH at 0xFE800000 and 0xFF800000 + * Out of reset this entry is only 4K. + */ + .long TLB1_MAS0(1, 0, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_BOOT_BLOCK), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_BOOT_BLOCK), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 1: 1G Non-cacheable, guarded + * 0x80000000 1G PCIE 8,9,a,b + */ + .long TLB1_MAS0(1, 1, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_1G) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCIE_PHYS), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCIE_PHYS), + 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 2: 256M Non-cacheable, guarded + */ + .long TLB1_MAS0(1, 2, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 3: 256M Non-cacheable, guarded + */ + .long TLB1_MAS0(1, 3, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI_PHYS + 0x10000000), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI_PHYS + 0x10000000), + 0,0,0,0,0,1,0,1,0,1) + + /* + * TLB 4: 64M Non-cacheable, guarded + * 0xe000_0000 1M CCSRBAR + * 0xe100_0000 255M PCI IO range + */ + .long TLB1_MAS0(1, 4, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + +#ifdef CFG_LBC_CACHE_BASE + /* + * TLB 5: 64M Cacheable, non-guarded + */ + .long TLB1_MAS0(1, 5, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_CACHE_BASE), 0,0,0,0,0,1,0,1,0,1) +#endif + /* + * TLB 6: 64M Non-cacheable, guarded + * 0xf8000000 64M PIXIS 0xF8000000 - 0xFBFFFFFF + */ + .long TLB1_MAS0(1, 6, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_NONCACHE_BASE), 0,0,0,0,0,1,0,1,0,1) +2: + entry_end + +/* + * LAW(Local Access Window) configuration: + * + * + * Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + * + * LAW 0 is reserved for boot mapping + */ + + .section .bootpg, "ax" + .globl law_entry +law_entry: + entry_start + + .long (4f-3f)/8 +3: + .long 0 + .long (LAWAR_TRGT_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN + + .long (CFG_PCI1_MEM_BASE>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M) + + .long (CFG_PCI1_IO_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M) + + .long (CFG_LBC_CACHE_BASE>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M) + + .long (CFG_PCIE1_MEM_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCIE1 | (LAWAR_SIZE & LAWAR_SIZE_256M) + + /* To keep to 10 LAWs, PCIE1_IO_PHYS must use top of mem region */ + + .long (CFG_PCIE2_MEM_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCIE2 | (LAWAR_SIZE & LAWAR_SIZE_512M) + + .long (CFG_PCIE2_IO_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCIE2 | (LAWAR_SIZE & LAWAR_SIZE_16M) + + .long (CFG_PCIE3_MEM_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCIE3 | (LAWAR_SIZE & LAWAR_SIZE_256M) + + .long (CFG_PCIE3_IO_PHYS>>12) & 0xfffff + .long LAWAR_EN | LAWAR_TRGT_PCIE3 | (LAWAR_SIZE & LAWAR_SIZE_16M) +4: + entry_end diff --git a/board/freescale/mpc8544ds/mpc8544ds.c b/board/freescale/mpc8544ds/mpc8544ds.c new file mode 100644 index 0000000000..4ff1da9301 --- /dev/null +++ b/board/freescale/mpc8544ds/mpc8544ds.c @@ -0,0 +1,201 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <command.h> +#include <asm/processor.h> +#include <asm/immap_85xx.h> +#include <spd.h> +#include <miiphy.h> + +#include "../common/pixis.h" + +#if defined(CONFIG_OF_FLAT_TREE) +#include <ft_build.h> +extern void ft_cpu_setup(void *blob, bd_t *bd); +#endif + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +extern void ddr_enable_ecc(unsigned int dram_size); +#endif + +extern long int spd_sdram(void); + +void sdram_init(void); + +int board_early_init_f (void) +{ + return 0; +} + +int checkboard (void) +{ + volatile immap_t *immap = (immap_t *) CFG_CCSRBAR; + volatile ccsr_gur_t *gur = &immap->im_gur; + + if ((uint)&gur->porpllsr != 0xe00e0000) { + printf("immap size error %x\n",&gur->porpllsr); + } + printf ("Board: MPC8544DS\n"); + + return 0; +} + +long int +initdram(int board_type) +{ + long dram_size = 0; + + puts("Initializing\n"); + + dram_size = spd_sdram(); + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* + * Initialize and enable DDR ECC. + */ + ddr_enable_ecc(dram_size); +#endif + puts(" DDR: "); + return dram_size; +} + +#if defined(CFG_DRAM_TEST) +int +testdram(void) +{ + uint *pstart = (uint *) CFG_MEMTEST_START; + uint *pend = (uint *) CFG_MEMTEST_END; + uint *p; + + printf("Testing DRAM from 0x%08x to 0x%08x\n", + CFG_MEMTEST_START, + CFG_MEMTEST_END); + + printf("DRAM test phase 1:\n"); + for (p = pstart; p < pend; p++) + *p = 0xaaaaaaaa; + + for (p = pstart; p < pend; p++) { + if (*p != 0xaaaaaaaa) { + printf ("DRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + printf("DRAM test phase 2:\n"); + for (p = pstart; p < pend; p++) + *p = 0x55555555; + + for (p = pstart; p < pend; p++) { + if (*p != 0x55555555) { + printf ("DRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + printf("DRAM test passed.\n"); + return 0; +} +#endif + +int last_stage_init(void) +{ + return 0; +} + + +unsigned long +get_board_sys_clk(ulong dummy) +{ + u8 i, go_bit, rd_clks; + ulong val = 0; + + go_bit = in8(PIXIS_BASE + PIXIS_VCTL); + go_bit &= 0x01; + + rd_clks = in8(PIXIS_BASE + PIXIS_VCFGEN0); + rd_clks &= 0x1C; + + /* + * Only if both go bit and the SCLK bit in VCFGEN0 are set + * should we be using the AUX register. Remember, we also set the + * GO bit to boot from the alternate bank on the on-board flash + */ + + if (go_bit) { + if (rd_clks == 0x1c) + i = in8(PIXIS_BASE + PIXIS_AUX); + else + i = in8(PIXIS_BASE + PIXIS_SPD); + } else { + i = in8(PIXIS_BASE + PIXIS_SPD); + } + + i &= 0x07; + + switch (i) { + case 0: + val = 33333333; + break; + case 1: + val = 40000000; + break; + case 2: + val = 50000000; + break; + case 3: + val = 66666666; + break; + case 4: + val = 83000000; + break; + case 5: + val = 100000000; + break; + case 6: + val = 133333333; + break; + case 7: + val = 166666666; + break; + } + + return val; +} + +#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) +void +ft_board_setup(void *blob, bd_t *bd) +{ + u32 *p; + int len; + + ft_cpu_setup(blob, bd); + + p = ft_get_prop(blob, "/memory/reg", &len); + if (p != NULL) { + *p++ = cpu_to_be32(bd->bi_memstart); + *p = cpu_to_be32(bd->bi_memsize); + } +} +#endif diff --git a/board/freescale/mpc8544ds/u-boot.lds b/board/freescale/mpc8544ds/u-boot.lds new file mode 100644 index 0000000000..1a8aaa9057 --- /dev/null +++ b/board/freescale/mpc8544ds/u-boot.lds @@ -0,0 +1,148 @@ +/* + * Copyright 2007 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ +SECTIONS +{ + .resetvec 0xFFFFFFFC : + { + *(.resetvec) + } = 0xffff + + .bootpg 0xFFFFF000 : + { + cpu/mpc85xx/start.o (.bootpg) + board/freescale/mpc8544ds/init.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc85xx/start.o (.text) + board/freescale/mpc8544ds/init.o (.text) + cpu/mpc85xx/traps.o (.text) + cpu/mpc85xx/interrupts.o (.text) + cpu/mpc85xx/cpu_init.o (.text) + cpu/mpc85xx/cpu.o (.text) + cpu/mpc85xx/speed.o (.text) + common/dlmalloc.o (.text) + lib_generic/crc32.o (.text) + lib_ppc/extable.o (.text) + lib_generic/zlib.o (.text) + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/board/ixdp425/config.mk b/board/ixdp425/config.mk index d49c0e7e6d..ecff8d7415 100644 --- a/board/ixdp425/config.mk +++ b/board/ixdp425/config.mk @@ -1,4 +1,2 @@ +# TEXT_BASE = 0x00f80000 - -# include NPE ethernet driver -BOARDLIBS = $(obj)cpu/ixp/npe/libnpe.a diff --git a/board/motionpro/motionpro.c b/board/motionpro/motionpro.c index d60d23332b..6eb5fe9cfc 100644 --- a/board/motionpro/motionpro.c +++ b/board/motionpro/motionpro.c @@ -28,7 +28,14 @@ #include <common.h> #include <mpc5xxx.h> +#include <miiphy.h> +#if defined(CONFIG_OF_FLAT_TREE) +#include <ft_build.h> +#endif +#if defined(CONFIG_STATUS_LED) +#include <status_led.h> +#endif /* CONFIG_STATUS_LED */ /* Kollmorgen DPR initialization data */ struct init_elem { @@ -75,11 +82,27 @@ int board_early_init_r(void) } +/* + * Additional PHY intialization. After being reset in mpc5xxx_fec_init_phy(), + * PHY goes into FX mode. To take it out of the FX mode and switch into + * desired TX operation, one needs to clear the FX_SEL bit of Mode Control + * Register. + */ +void reset_phy(void) +{ + unsigned short mode_control; + + miiphy_read("FEC ETHERNET", CONFIG_PHY_ADDR, 0x15, &mode_control); + miiphy_write("FEC ETHERNET", CONFIG_PHY_ADDR, 0x15, + mode_control & 0xfffe); + return; +} + #ifndef CFG_RAMBOOT /* * Helper function to initialize SDRAM controller. */ -static void sdram_start (int hi_addr) +static void sdram_start(int hi_addr) { long hi_addr_bit = hi_addr ? 0x01000000 : 0; @@ -111,7 +134,7 @@ static void sdram_start (int hi_addr) /* * Initalize SDRAM - configure SDRAM controller, detect memory size. */ -long int initdram (int board_type) +long int initdram(int board_type) { ulong dramsize = 0; #ifndef CFG_RAMBOOT @@ -165,8 +188,43 @@ long int initdram (int board_type) } -int checkboard (void) +int checkboard(void) { - puts("Board: Promess Motion-PRO board\n"); + uchar rev = *(vu_char *)CPLD_REV_REGISTER; + printf("Board: Promess Motion-PRO board (CPLD rev. 0x%02x)\n", rev); return 0; } + + +#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + ft_cpu_setup(blob, bd); +} +#endif /* defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) */ + + +#if defined(CONFIG_STATUS_LED) +void __led_init(led_id_t regaddr, int state) +{ + *((vu_long *) regaddr) |= ENABLE_GPIO_OUT; + + if (state == STATUS_LED_ON) + *((vu_long *) regaddr) |= LED_ON; + else + *((vu_long *) regaddr) &= ~LED_ON; +} + +void __led_set(led_id_t regaddr, int state) +{ + if (state == STATUS_LED_ON) + *((vu_long *) regaddr) |= LED_ON; + else + *((vu_long *) regaddr) &= ~LED_ON; +} + +void __led_toggle(led_id_t regaddr) +{ + *((vu_long *) regaddr) ^= LED_ON; +} +#endif /* CONFIG_STATUS_LED */ diff --git a/board/mpc8313erdb/Makefile b/board/mpc8313erdb/Makefile new file mode 100644 index 0000000000..a987e510dd --- /dev/null +++ b/board/mpc8313erdb/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o sdram.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(AR) crv $@ $(OBJS) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/mpc8313erdb/config.mk b/board/mpc8313erdb/config.mk new file mode 100644 index 0000000000..f76826495e --- /dev/null +++ b/board/mpc8313erdb/config.mk @@ -0,0 +1 @@ +TEXT_BASE = 0xFE000000 diff --git a/board/mpc8313erdb/mpc8313erdb.c b/board/mpc8313erdb/mpc8313erdb.c new file mode 100644 index 0000000000..999fe9e39b --- /dev/null +++ b/board/mpc8313erdb/mpc8313erdb.c @@ -0,0 +1,116 @@ +/* + * Copyright (C) Freescale Semiconductor, Inc. 2006-2007 + * + * Author: Scott Wood <scottwood@freescale.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <ft_build.h> +#include <pci.h> +#include <mpc83xx.h> + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ +#ifndef CFG_8313ERDB_BROKEN_PMC + volatile immap_t *im = (immap_t *)CFG_IMMR; + + if (im->pmc.pmccr1 & PMCCR1_POWER_OFF) + gd->flags |= GD_FLG_SILENT; +#endif + + return 0; +} + +int checkboard(void) +{ + puts("Board: Freescale MPC8313ERDB\n"); + return 0; +} + +static struct pci_region pci_regions[] = { + { + bus_start: CFG_PCI1_MEM_BASE, + phys_start: CFG_PCI1_MEM_PHYS, + size: CFG_PCI1_MEM_SIZE, + flags: PCI_REGION_MEM | PCI_REGION_PREFETCH + }, + { + bus_start: CFG_PCI1_MMIO_BASE, + phys_start: CFG_PCI1_MMIO_PHYS, + size: CFG_PCI1_MMIO_SIZE, + flags: PCI_REGION_MEM + }, + { + bus_start: CFG_PCI1_IO_BASE, + phys_start: CFG_PCI1_IO_PHYS, + size: CFG_PCI1_IO_SIZE, + flags: PCI_REGION_IO + } +}; + +void pci_init_board(void) +{ + volatile immap_t *immr = (volatile immap_t *)CFG_IMMR; + volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk; + volatile law83xx_t *pci_law = immr->sysconf.pcilaw; + struct pci_region *reg[] = { pci_regions }; + int warmboot; + + /* Enable all 3 PCI_CLK_OUTPUTs. */ + clk->occr |= 0xe0000000; + + /* + * Configure PCI Local Access Windows + */ + pci_law[0].bar = CFG_PCI1_MEM_PHYS & LAWBAR_BAR; + pci_law[0].ar = LBLAWAR_EN | LBLAWAR_512MB; + + pci_law[1].bar = CFG_PCI1_IO_PHYS & LAWBAR_BAR; + pci_law[1].ar = LBLAWAR_EN | LBLAWAR_1MB; + + warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM; +#ifndef CFG_8313ERDB_BROKEN_PMC + warmboot |= immr->pmc.pmccr1 & PMCCR1_POWER_OFF; +#endif + + mpc83xx_pci_init(1, reg, warmboot); +} + +#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) +void ft_board_setup(void *blob, bd_t *bd) +{ + u32 *p; + int len; + +#ifdef CONFIG_PCI + ft_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); + + p = ft_get_prop(blob, "/memory/reg", &len); + if (p) { + *p++ = cpu_to_be32(bd->bi_memstart); + *p = cpu_to_be32(bd->bi_memsize); + } +} +#endif diff --git a/board/mpc8313erdb/sdram.c b/board/mpc8313erdb/sdram.c new file mode 100644 index 0000000000..4b6778837f --- /dev/null +++ b/board/mpc8313erdb/sdram.c @@ -0,0 +1,133 @@ +/* + * Copyright (C) Freescale Semiconductor, Inc. 2006-2007 + * + * Authors: Nick.Spence@freescale.com + * Wilson.Lo@freescale.com + * scottwood@freescale.com + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <mpc83xx.h> +#include <spd_sdram.h> + +#include <asm/bitops.h> +#include <asm/io.h> + +#include <asm/processor.h> + +#ifndef CFG_8313ERDB_BROKEN_PMC +static void resume_from_sleep(void) +{ + DECLARE_GLOBAL_DATA_PTR; + u32 magic = *(u32 *)0; + + typedef void (*func_t)(void); + func_t resume = *(func_t *)4; + + if (magic == 0xf5153ae5) + resume(); + + gd->flags &= ~GD_FLG_SILENT; + puts("\nResume from sleep failed: bad magic word\n"); +} +#endif + +/* Fixed sdram init -- doesn't use serial presence detect. + * + * This is useful for faster booting in configs where the RAM is unlikely + * to be changed, or for things like NAND booting where space is tight. + */ +static long fixed_sdram(void) +{ + volatile immap_t *im = (volatile immap_t *)CFG_IMMR; + u32 msize = CFG_DDR_SIZE * 1024 * 1024; + u32 msize_log2 = __ilog2(msize); + + im->sysconf.ddrlaw[0].bar = CFG_DDR_SDRAM_BASE >> 12; + im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1); + im->sysconf.ddrcdr = CFG_DDRCDR_VALUE; + + /* + * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg], + * or the DDR2 controller may fail to initialize correctly. + */ + udelay(50000); + + im->ddr.csbnds[0].csbnds = (msize - 1) >> 24; + im->ddr.cs_config[0] = CFG_DDR_CONFIG; + + /* Currently we use only one CS, so disable the other bank. */ + im->ddr.cs_config[1] = 0; + + im->ddr.sdram_clk_cntl = CFG_DDR_CLK_CNTL; + im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3; + im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1; + im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2; + im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0; + +#ifndef CFG_8313ERDB_BROKEN_PMC + if (im->pmc.pmccr1 & PMCCR1_POWER_OFF) + im->ddr.sdram_cfg = CFG_SDRAM_CFG | SDRAM_CFG_BI; + else +#endif + im->ddr.sdram_cfg = CFG_SDRAM_CFG; + + im->ddr.sdram_cfg2 = CFG_SDRAM_CFG2; + im->ddr.sdram_mode = CFG_DDR_MODE; + im->ddr.sdram_mode2 = CFG_DDR_MODE_2; + + im->ddr.sdram_interval = CFG_DDR_INTERVAL; + sync(); + + /* enable DDR controller */ + im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN; + + return msize; +} + +long int initdram(int board_type) +{ + volatile immap_t *im = (volatile immap_t *)CFG_IMMR; + volatile lbus83xx_t *lbc = &im->lbus; + u32 msize; + + if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im) + return -1; + + puts("Initializing\n"); + + /* DDR SDRAM - Main SODIMM */ + msize = fixed_sdram(); + + /* Local Bus setup lbcr and mrtpr */ + lbc->lbcr = CFG_LBC_LBCR; + lbc->mrtpr = CFG_LBC_MRTPR; + sync(); + +#ifndef CFG_8313ERDB_BROKEN_PMC + if (im->pmc.pmccr1 & PMCCR1_POWER_OFF) + resume_from_sleep(); +#endif + + puts(" DDR RAM: "); + /* return total bus SDRAM size(bytes) -- DDR */ + return msize; +} diff --git a/board/mpc8313erdb/u-boot.lds b/board/mpc8313erdb/u-boot.lds new file mode 100644 index 0000000000..937c87a27c --- /dev/null +++ b/board/mpc8313erdb/u-boot.lds @@ -0,0 +1,123 @@ +/* + * (C) Copyright 2006 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SECTIONS +{ + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc83xx/start.o (.text) + *(.text) + *(.fixup) + *(.got1) + . = ALIGN(16); + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x0FFF) & 0xFFFFF000; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(4096); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(4096); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} +ENTRY(_start) diff --git a/board/mpc8349itx/mpc8349itx.c b/board/mpc8349itx/mpc8349itx.c index 2b3ded1762..178b1d36fb 100644 --- a/board/mpc8349itx/mpc8349itx.c +++ b/board/mpc8349itx/mpc8349itx.c @@ -80,8 +80,7 @@ int fixed_sdram(void) im->ddr.sdram_interval = (0x0410 << SDRAM_INTERVAL_REFINT_SHIFT) | (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT); - im->ddr.sdram_clk_cntl = - DDR_SDRAM_CLK_CNTL_SS_EN | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05; + im->ddr.sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL; udelay(200); diff --git a/board/mpc8540ads/init.S b/board/mpc8540ads/init.S index 242cb9fbc1..544fde94c4 100644 --- a/board/mpc8540ads/init.S +++ b/board/mpc8540ads/init.S @@ -260,8 +260,8 @@ tlb1_entry: #define LAWBAR2 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff) #define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M)) -#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff) -#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M)) +#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff) +#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_1M)) /* * Rapid IO at 0xc000_0000 for 512 M diff --git a/board/mpc8560ads/init.S b/board/mpc8560ads/init.S index 242cb9fbc1..544fde94c4 100644 --- a/board/mpc8560ads/init.S +++ b/board/mpc8560ads/init.S @@ -260,8 +260,8 @@ tlb1_entry: #define LAWBAR2 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff) #define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M)) -#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff) -#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M)) +#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff) +#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_1M)) /* * Rapid IO at 0xc000_0000 for 512 M diff --git a/board/mpc8568mds/Makefile b/board/mpc8568mds/Makefile new file mode 100644 index 0000000000..a799aa4cc5 --- /dev/null +++ b/board/mpc8568mds/Makefile @@ -0,0 +1,58 @@ +# +# Copyright 2004-2007 Freescale Semiconductor. +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk +ifneq ($(OBJTREE),$(SRCTREE)) +$(shell mkdir -p $(obj)../common) +endif + +LIB = $(obj)lib$(BOARD).a + +COBJS := $(BOARD).o \ + bcsr.o \ + ft_board.o + +SOBJS := init.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(AR) $(ARFLAGS) $@ $(OBJS) + +clean: + rm -f $(OBJS) $(SOBJS) + +distclean: clean + rm -f $(LIB) core *.bak .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/mpc8568mds/bcsr.c b/board/mpc8568mds/bcsr.c new file mode 100644 index 0000000000..2e2e8cd18f --- /dev/null +++ b/board/mpc8568mds/bcsr.c @@ -0,0 +1,49 @@ +/* + * Copyright 2007 Freescale Semiconductor. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include "bcsr.h" + +void enable_8568mds_duart() +{ + volatile uint* duart_mux = (uint *)(CFG_CCSRBAR + 0xe0060); + volatile uint* devices = (uint *)(CFG_CCSRBAR + 0xe0070); + volatile u8 *bcsr = (u8 *)(CFG_BCSR); + + *duart_mux = 0x80000000; /* Set the mux to Duart on PMUXCR */ + *devices = 0; /* Enable all peripheral devices */ + bcsr[5] |= 0x01; /* Enable Duart in BCSR*/ +} + +void enable_8568mds_flash_write() +{ + volatile u8 *bcsr = (u8 *)(CFG_BCSR); + + bcsr[9] |= 0x01; +} + +void disable_8568mds_flash_write() +{ + volatile u8 *bcsr = (u8 *)(CFG_BCSR); + + bcsr[9] &= ~(0x01); +} diff --git a/board/mpc8568mds/bcsr.h b/board/mpc8568mds/bcsr.h new file mode 100644 index 0000000000..8d4cb2f141 --- /dev/null +++ b/board/mpc8568mds/bcsr.h @@ -0,0 +1,99 @@ +/* + * Copyright 2007 Freescale Semiconductor. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __BCSR_H_ +#define __BCSR_H_ + +#include <common.h> + +/* BCSR Bit definitions + * BCSR 0 * + 0:3 ccb sys pll + 4:6 cfg core pll + 7 cfg boot seq + + * BCSR 1 * + 0:2 cfg rom lock + 3:5 cfg host agent + 6 PCI IO + 7 cfg RIO size + + * BCSR 2 * + 0:4 QE PLL + 5 QE clock + 6 cfg PCI arbiter + + * BCSR 3 * + 0 TSEC1 reduce + 1 TSEC2 reduce + 2:3 TSEC1 protocol + 4:5 TSEC2 protocol + 6 PHY1 slave + 7 PHY2 slave + + * BCSR 4 * + 4 clock enable + 5 boot EPROM + 6 GETH transactive reset + 7 BRD write potect + + * BCSR 5 * + 1:3 Leds 1-3 + 4 UPC1 enable + 5 UPC2 enable + 6 UPC2 pos + 7 RS232 enable + + * BCSR 6 * + 0 CFG ver 0 + 1 CFG ver 1 + 6 Register config led + 7 Power on reset + + * BCSR 7 * + 2 board host mode indication + 5 enable TSEC1 PHY + 6 enable TSEC2 PHY + + * BCSR 8 * + 0 UCC GETH1 enable + 1 UCC GMII enable + 3 UCC TBI enable + 5 UCC MII enable + 7 Real time clock reset + + * BCSR 9 * + 0 UCC2 GETH enable + 1 UCC2 GMII enable + 3 UCC2 TBI enable + 5 UCC2 MII enable + 6 Ready only - indicate flash ready after burning + 7 Flash write protect +*/ + +/*BCSR Utils functions*/ + +void enable_8568mds_duart(void); +void enable_8568mds_flash_write(void); +void disable_8568mds_flash_write(void); + +#endif /* __BCSR_H_ */ diff --git a/board/mpc8568mds/config.mk b/board/mpc8568mds/config.mk new file mode 100644 index 0000000000..021522cafc --- /dev/null +++ b/board/mpc8568mds/config.mk @@ -0,0 +1,30 @@ +# +# Copyright 2007 Freescale Semiconductor. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +# +# mpc8568mds board +# +TEXT_BASE = 0xfff80000 + +PLATFORM_CPPFLAGS += -DCONFIG_E500=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1 +PLATFORM_CPPFLAGS += -DCONFIG_MPC8568=1 diff --git a/board/mpc8568mds/ft_board.c b/board/mpc8568mds/ft_board.c new file mode 100644 index 0000000000..36815ccfbb --- /dev/null +++ b/board/mpc8568mds/ft_board.c @@ -0,0 +1,45 @@ +/* + * Copyright 2004-2007 Freescale Semiconductor. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> + +#include <ft_build.h> + +extern void ft_cpu_setup(void *blob, bd_t *bd); + +#if defined(CONFIG_OF_FLAT_TREE) && defined(CONFIG_OF_BOARD_SETUP) +void +ft_board_setup(void *blob, bd_t *bd) +{ + u32 *p; + int len; +#ifdef CONFIG_PCI + ft_pci_setup(blob, bd); +#endif + ft_cpu_setup(blob, bd); + p = ft_get_prop(blob, "/memory/reg", &len); + if (p != NULL) { + *p++ = cpu_to_be32(bd->bi_memstart); + *p = cpu_to_be32(bd->bi_memsize); + } +} +#endif /* CONFIG_OF_FLAT_TREE && CONFIG_OF_BOARD_SETUP */ diff --git a/board/mpc8568mds/init.S b/board/mpc8568mds/init.S new file mode 100644 index 0000000000..0d879821e3 --- /dev/null +++ b/board/mpc8568mds/init.S @@ -0,0 +1,258 @@ +/* + * Copyright 2004-2007 Freescale Semiconductor. + * Copyright 2002,2003, Motorola Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <ppc_asm.tmpl> +#include <ppc_defs.h> +#include <asm/cache.h> +#include <asm/mmu.h> +#include <config.h> +#include <mpc85xx.h> + + +/* + * TLB0 and TLB1 Entries + * + * Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR. + * However, CCSRBAR is then relocated to CFG_CCSRBAR right after + * these TLB entries are established. + * + * The TLB entries for DDR are dynamically setup in spd_sdram() + * and use TLB1 Entries 8 through 15 as needed according to the + * size of DDR memory. + * + * MAS0: tlbsel, esel, nv + * MAS1: valid, iprot, tid, ts, tsize + * MAS2: epn, sharen, x0, x1, w, i, m, g, e + * MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr + */ +#define entry_start \ + mflr r1 ; \ + bl 0f ; + +#define entry_end \ +0: mflr r0 ; \ + mtlr r1 ; \ + blr ; + + + .section .bootpg, "ax" + .globl tlb1_entry +tlb1_entry: + entry_start + + /* + * Number of TLB0 and TLB1 entries in the following table + */ + .long (2f-1f)/16 + +1: +#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR) + /* + * TLB0 4K Non-cacheable, guarded + * 0xff700000 4K Initial CCSRBAR mapping + * + * This ends up at a TLB0 Index==0 entry, and must not collide + * with other TLB0 Entries. + */ + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1) +#else +#error("Update the number of table entries in tlb1_entry") +#endif + + /* + * TLB0 16K Cacheable, non-guarded + * 0xd001_0000 16K Temporary Global data for initialization + * + * Use four 4K TLB0 entries. These entries must be cacheable + * as they provide the bootstrap memory before the memory + * controler and real memory have been configured. + * + * These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c, + * and must not collide with other TLB0 entries. + */ + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR), 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR), 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + .long TLB1_MAS0(0, 0, 0) + .long TLB1_MAS1(1, 0, 0, 0, 0) + .long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024), + 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024), + 0,0,0,0,0,1,0,1,0,1) + + /* TLB 1 Initializations */ + /* + * TLBe 0: 16M Non-cacheable, guarded + * 0xff000000 16M FLASH (upper half) + * Out of reset this entry is only 4K. + */ + .long TLB1_MAS0(1, 0, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE + 0x1000000), + 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE + 0x1000000), + 0,0,0,0,0,1,0,1,0,1) + + /* + * TLBe 1: 16M Non-cacheable, guarded + * 0xfe000000 16M FLASH (lower half) + */ + .long TLB1_MAS0(1, 1, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLBe 2: 256M Non-cacheable, guarded + * 0x80000000 256M PCI1 MEM + */ + .long TLB1_MAS0(1, 2, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLBe 3: 256M Non-cacheable, guarded + * 0xa0000000 256M PCIe Mem + */ + .long TLB1_MAS0(1, 3, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_PEX_MEM_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_PEX_MEM_BASE), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLBe 4: Reserved for future usage + */ + + /* + * TLBe 5: 64M Non-cacheable, guarded + * 0xe000_0000 1M CCSRBAR + * 0xe200_0000 8M PCI1 IO + * 0xe280_0000 8M PCIe IO + */ + .long TLB1_MAS0(1, 5, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLBe 6: 64M Cacheable, non-guarded + * 0xf000_0000 64M LBC SDRAM + */ + .long TLB1_MAS0(1, 6, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M) + .long TLB1_MAS2(E500_TLB_EPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,0,0,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_LBC_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1) + + /* + * TLBe 7: 256K Non-cacheable, guarded + * 0xf8000000 32K BCSR + * 0xf8008000 32K PIB (CS4) + * 0xf8010000 32K PIB (CS5) + */ + .long TLB1_MAS0(1, 7, 0) + .long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256K) + .long TLB1_MAS2(E500_TLB_EPN(CFG_BCSR_BASE), 0,0,0,0,1,0,1,0) + .long TLB1_MAS3(E500_TLB_RPN(CFG_BCSR_BASE), 0,0,0,0,0,1,0,1,0,1) + +2: + entry_end + +/* + * LAW(Local Access Window) configuration: + * + *0) 0x0000_0000 0x7fff_ffff DDR 2G + *1) 0x8000_0000 0x9fff_ffff PCI1 MEM 256MB + *2) 0xa000_0000 0xbfff_ffff PCIe MEM 256MB + *5) 0xc000_0000 0xdfff_ffff SRIO 256MB + *-) 0xe000_0000 0xe00f_ffff CCSR 1M + *3) 0xe200_0000 0xe27f_ffff PCI1 I/O 8M + *4) 0xe280_0000 0xe2ff_ffff PCIe I/0 8M + *6.a) 0xf000_0000 0xf3ff_ffff SDRAM 64MB + *6.b) 0xf800_0000 0xf800_7fff BCSR 32KB + *6.c) 0xf800_8000 0xf800_ffff PIB (CS4) 32KB + *6.d) 0xf801_0000 0xf801_7fff PIB (CS5) 32KB + *6.e) 0xfe00_0000 0xffff_ffff Flash 32MB + * + *Notes: + * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window. + * If flash is 8M at default position (last 8M), no LAW needed. + * + * The defines below are 1-off of the actual LAWAR0 usage. + * So LAWAR3 define uses the LAWAR4 register in the ECM. + */ + +#define LAWBAR0 0 +#define LAWAR0 ((LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_128M)) & ~LAWAR_EN) + +#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff) +#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_256M)) + +#define LAWBAR2 ((CFG_PEX_MEM_BASE>>12) & 0xfffff) +#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_256M)) + +#define LAWBAR3 ((CFG_PCI1_IO_PHYS>>12) & 0xfffff) +#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_8M)) + +#define LAWBAR4 ((CFG_PEX_IO_PHYS>>12) & 0xfffff) +#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_PEX | (LAWAR_SIZE & LAWAR_SIZE_16M)) + + +#define LAWBAR5 ((CFG_SRIO_MEM_BASE>>12) & 0xfffff) +#define LAWAR5 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_256M)) + +/* LBC window - maps 256M. That's SDRAM, BCSR, PIBs, and Flash */ +#define LAWBAR6 ((CFG_LBC_SDRAM_BASE>>12) & 0xfffff) +#define LAWAR6 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_256M)) + + .section .bootpg, "ax" + .globl law_entry + +law_entry: + entry_start + .long (4f-3f)/8 +3: + .long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3 + .long LAWBAR4,LAWAR4,LAWBAR5,LAWAR5,LAWBAR6,LAWAR6 +4: + entry_end diff --git a/board/mpc8568mds/mpc8568mds.c b/board/mpc8568mds/mpc8568mds.c new file mode 100644 index 0000000000..9c7960d47e --- /dev/null +++ b/board/mpc8568mds/mpc8568mds.c @@ -0,0 +1,288 @@ +/* + * Copyright 2007 Freescale Semiconductor. + * + * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <pci.h> +#include <asm/processor.h> +#include <asm/immap_85xx.h> +#include <spd.h> + +#include "bcsr.h" + + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) +extern void ddr_enable_ecc(unsigned int dram_size); +#endif + +extern long int spd_sdram(void); + +void local_bus_init(void); +void sdram_init(void); + +int board_early_init_f (void) +{ + /* + * Initialize local bus. + */ + local_bus_init (); + + enable_8568mds_duart(); + enable_8568mds_flash_write(); + + return 0; +} + +int checkboard (void) +{ + printf ("Board: 8568 MDS\n"); + + return 0; +} + +long int +initdram(int board_type) +{ + long dram_size = 0; + volatile immap_t *immap = (immap_t *)CFG_IMMR; + + puts("Initializing\n"); + +#if defined(CONFIG_DDR_DLL) + { + /* + * Work around to stabilize DDR DLL MSYNC_IN. + * Errata DDR9 seems to have been fixed. + * This is now the workaround for Errata DDR11: + * Override DLL = 1, Course Adj = 1, Tap Select = 0 + */ + + volatile ccsr_gur_t *gur= &immap->im_gur; + + gur->ddrdllcr = 0x81000000; + asm("sync;isync;msync"); + udelay(200); + } +#endif + dram_size = spd_sdram(); + +#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) + /* + * Initialize and enable DDR ECC. + */ + ddr_enable_ecc(dram_size); +#endif + /* + * SDRAM Initialization + */ + sdram_init(); + + puts(" DDR: "); + return dram_size; +} + +/* + * Initialize Local Bus + */ +void +local_bus_init(void) +{ + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile ccsr_gur_t *gur = &immap->im_gur; + volatile ccsr_lbc_t *lbc = &immap->im_lbc; + + uint clkdiv; + uint lbc_hz; + sys_info_t sysinfo; + + get_sys_info(&sysinfo); + clkdiv = (lbc->lcrr & 0x0f) * 2; + lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv; + + gur->lbiuiplldcr1 = 0x00078080; + if (clkdiv == 16) { + gur->lbiuiplldcr0 = 0x7c0f1bf0; + } else if (clkdiv == 8) { + gur->lbiuiplldcr0 = 0x6c0f1bf0; + } else if (clkdiv == 4) { + gur->lbiuiplldcr0 = 0x5c0f1bf0; + } + + lbc->lcrr |= 0x00030000; + + asm("sync;isync;msync"); +} + +/* + * Initialize SDRAM memory on the Local Bus. + */ +void +sdram_init(void) +{ +#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM) + + uint idx; + volatile immap_t *immap = (immap_t *)CFG_IMMR; + volatile ccsr_lbc_t *lbc = &immap->im_lbc; + uint *sdram_addr = (uint *)CFG_LBC_SDRAM_BASE; + uint lsdmr_common; + + puts(" SDRAM: "); + + print_size (CFG_LBC_SDRAM_SIZE * 1024 * 1024, "\n"); + + /* + * Setup SDRAM Base and Option Registers + */ + lbc->or2 = CFG_OR2_PRELIM; + asm("msync"); + + lbc->br2 = CFG_BR2_PRELIM; + asm("msync"); + + lbc->lbcr = CFG_LBC_LBCR; + asm("msync"); + + + lbc->lsrt = CFG_LBC_LSRT; + lbc->mrtpr = CFG_LBC_MRTPR; + asm("msync"); + + /* + * MPC8568 uses "new" 15-16 style addressing. + */ + lsdmr_common = CFG_LBC_LSDMR_COMMON; + lsdmr_common |= CFG_LBC_LSDMR_BSMA1516; + + /* + * Issue PRECHARGE ALL command. + */ + lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_PCHALL; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(100); + + /* + * Issue 8 AUTO REFRESH commands. + */ + for (idx = 0; idx < 8; idx++) { + lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_ARFRSH; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(100); + } + + /* + * Issue 8 MODE-set command. + */ + lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_MRW; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(100); + + /* + * Issue NORMAL OP command. + */ + lbc->lsdmr = lsdmr_common | CFG_LBC_LSDMR_OP_NORMAL; + asm("sync;msync"); + *sdram_addr = 0xff; + ppcDcbf((unsigned long) sdram_addr); + udelay(200); /* Overkill. Must wait > 200 bus cycles */ + +#endif /* enable SDRAM init */ +} + +#if defined(CFG_DRAM_TEST) +int +testdram(void) +{ + uint *pstart = (uint *) CFG_MEMTEST_START; + uint *pend = (uint *) CFG_MEMTEST_END; + uint *p; + + printf("Testing DRAM from 0x%08x to 0x%08x\n", + CFG_MEMTEST_START, + CFG_MEMTEST_END); + + printf("DRAM test phase 1:\n"); + for (p = pstart; p < pend; p++) + *p = 0xaaaaaaaa; + + for (p = pstart; p < pend; p++) { + if (*p != 0xaaaaaaaa) { + printf ("DRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + printf("DRAM test phase 2:\n"); + for (p = pstart; p < pend; p++) + *p = 0x55555555; + + for (p = pstart; p < pend; p++) { + if (*p != 0x55555555) { + printf ("DRAM test fails at: %08x\n", (uint) p); + return 1; + } + } + + printf("DRAM test passed.\n"); + return 0; +} +#endif + +#if defined(CONFIG_PCI) +#ifndef CONFIG_PCI_PNP +static struct pci_config_table pci_mpc8568mds_config_table[] = { + { + PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, + pci_cfgfunc_config_device, + {PCI_ENET0_IOADDR, + PCI_ENET0_MEMADDR, + PCI_COMMON_MEMORY | PCI_COMMAND_MASTER} + }, + {} +}; +#endif + +static struct pci_controller hose[] = { +#ifndef CONFIG_PCI_PNP + { config_table: pci_mpc8568mds_config_table,}, +#endif +#ifdef CONFIG_MPC85XX_PCI2 + {}, +#endif +}; + +#endif /* CONFIG_PCI */ + +void +pci_init_board(void) +{ +#ifdef CONFIG_PCI + pci_mpc85xx_init(&hose); +#endif +} diff --git a/board/mpc8568mds/u-boot.lds b/board/mpc8568mds/u-boot.lds new file mode 100644 index 0000000000..71099f6f13 --- /dev/null +++ b/board/mpc8568mds/u-boot.lds @@ -0,0 +1,152 @@ +/* + * Copyright 2004-2007 Freescale Semiconductor. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +OUTPUT_ARCH(powerpc) +SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib); +/* Do we need any of these for elf? + __DYNAMIC = 0; */ + +SECTIONS +{ + /* ELIOR - From RAM: From FLASH: 0xFFFFFFFC*/ + .resetvec 0xFFFFFFFC: + { + *(.resetvec) + } = 0xffff + + /*(ELIOR - From RAM: From FLASH: 0xFFFFF000*/ + .bootpg 0xFFFFF000: + { + cpu/mpc85xx/start.o (.bootpg) + board/mpc8568mds/init.o (.bootpg) + } = 0xffff + + /* Read-only sections, merged into text segment: */ + . = + SIZEOF_HEADERS; + .interp : { *(.interp) } + .hash : { *(.hash) } + .dynsym : { *(.dynsym) } + .dynstr : { *(.dynstr) } + .rel.text : { *(.rel.text) } + .rela.text : { *(.rela.text) } + .rel.data : { *(.rel.data) } + .rela.data : { *(.rela.data) } + .rel.rodata : { *(.rel.rodata) } + .rela.rodata : { *(.rela.rodata) } + .rel.got : { *(.rel.got) } + .rela.got : { *(.rela.got) } + .rel.ctors : { *(.rel.ctors) } + .rela.ctors : { *(.rela.ctors) } + .rel.dtors : { *(.rel.dtors) } + .rela.dtors : { *(.rela.dtors) } + .rel.bss : { *(.rel.bss) } + .rela.bss : { *(.rela.bss) } + .rel.plt : { *(.rel.plt) } + .rela.plt : { *(.rela.plt) } + .init : { *(.init) } + .plt : { *(.plt) } + .text : + { + cpu/mpc85xx/start.o (.text) + board/mpc8568mds/init.o (.text) + cpu/mpc85xx/traps.o (.text) + cpu/mpc85xx/interrupts.o (.text) + cpu/mpc85xx/cpu_init.o (.text) + cpu/mpc85xx/cpu.o (.text) + cpu/mpc85xx/speed.o (.text) + cpu/mpc85xx/pci.o (.text) + common/dlmalloc.o (.text) + lib_generic/crc32.o (.text) + lib_ppc/extable.o (.text) + lib_generic/zlib.o (.text) + *(.text) + *(.fixup) + *(.got1) + } + _etext = .; + PROVIDE (etext = .); + .rodata : + { + *(.rodata) + *(.rodata1) + *(.rodata.str1.4) + *(.eh_frame) + } + .fini : { *(.fini) } =0 + .ctors : { *(.ctors) } + .dtors : { *(.dtors) } + + /* Read-write section, merged into data segment: */ + . = (. + 0x00FF) & 0xFFFFFF00; + _erotext = .; + PROVIDE (erotext = .); + .reloc : + { + *(.got) + _GOT2_TABLE_ = .; + *(.got2) + _FIXUP_TABLE_ = .; + *(.fixup) + } + __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2; + __fixup_entries = (. - _FIXUP_TABLE_) >> 2; + + .data : + { + *(.data) + *(.data1) + *(.sdata) + *(.sdata2) + *(.dynamic) + CONSTRUCTORS + } + _edata = .; + PROVIDE (edata = .); + + . = .; + __u_boot_cmd_start = .; + .u_boot_cmd : { *(.u_boot_cmd) } + __u_boot_cmd_end = .; + + . = .; + __start___ex_table = .; + __ex_table : { *(__ex_table) } + __stop___ex_table = .; + + . = ALIGN(256); + __init_begin = .; + .text.init : { *(.text.init) } + .data.init : { *(.data.init) } + . = ALIGN(256); + __init_end = .; + + __bss_start = .; + .bss : + { + *(.sbss) *(.scommon) + *(.dynbss) + *(.bss) + *(COMMON) + } + _end = . ; + PROVIDE (end = .); +} diff --git a/board/mpc8641hpcn/init.S b/board/mpc8641hpcn/init.S index 6b3e2d275d..cb21ba6a75 100644 --- a/board/mpc8641hpcn/init.S +++ b/board/mpc8641hpcn/init.S @@ -59,7 +59,7 @@ #define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_512M)) #define LAWBAR3 ((CFG_PCI2_MEM_BASE>>12) & 0xffffff) -#define LAWAR3 (~LAWAR_EN & (LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M))) +#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_512M)) /* * This is not so much the SDRAM map as it is the whole localbus map. @@ -67,11 +67,11 @@ #define LAWBAR4 ((0xf8100000>>12) & 0xffffff) #define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_2M)) -#define LAWBAR5 ((CFG_PCI1_IO_BASE>>12) & 0xffffff) +#define LAWBAR5 ((CFG_PCI1_IO_PHYS>>12) & 0xffffff) #define LAWAR5 (LAWAR_EN | LAWAR_TRGT_IF_PCI1 | (LAWAR_SIZE & LAWAR_SIZE_16M)) -#define LAWBAR6 ((CFG_PCI2_IO_BASE>>12) & 0xffffff) -#define LAWAR6 (~LAWAR_EN &( LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M))) +#define LAWBAR6 ((CFG_PCI2_IO_PHYS>>12) & 0xffffff) +#define LAWAR6 (LAWAR_EN | LAWAR_TRGT_IF_PCI2 | (LAWAR_SIZE & LAWAR_SIZE_16M)) #define LAWBAR7 ((0xfe000000 >>12) & 0xffffff) #define LAWAR7 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_32M)) @@ -84,7 +84,7 @@ #define LAWAR8 ((LAWAR_TRGT_IF_DDR2 | (LAWAR_SIZE & LAWAR_SIZE_512M)) & ~LAWAR_EN) #endif -#define LAWBAR9 ((CFG_RIO_MEM_BASE>>12) & 0xfffff) +#define LAWBAR9 ((CFG_RIO_MEM_PHYS>>12) & 0xfffff) #define LAWAR9 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M)) .section .bootpg, "ax" diff --git a/board/prodrive/pdnb3/config.mk b/board/prodrive/pdnb3/config.mk index 767075884a..51dee86ae5 100644 --- a/board/prodrive/pdnb3/config.mk +++ b/board/prodrive/pdnb3/config.mk @@ -1,4 +1,2 @@ +# TEXT_BASE = 0x01f00000 - -# include NPE ethernet driver -BOARDLIBS = $(obj)cpu/ixp/npe/libnpe.a diff --git a/board/xilinx/ml401/config.mk b/board/xilinx/ml401/config.mk index 807f169fa7..c75daaf0b5 100644 --- a/board/xilinx/ml401/config.mk +++ b/board/xilinx/ml401/config.mk @@ -25,7 +25,7 @@ # Version: Xilinx EDK 6.3 EDK_Gmm.12.3 # -TEXT_BASE = 0x12000000 +TEXT_BASE = 0x29000000 PLATFORM_CPPFLAGS += -mno-xl-soft-mul PLATFORM_CPPFLAGS += -mno-xl-soft-div diff --git a/board/xilinx/ml401/ml401.c b/board/xilinx/ml401/ml401.c index b48103fdc0..955936d907 100644 --- a/board/xilinx/ml401/ml401.c +++ b/board/xilinx/ml401/ml401.c @@ -27,6 +27,8 @@ #include <common.h> #include <config.h> +#include <asm/microblaze_intc.h> +#include <asm/asm.h> void do_reset (void) { @@ -43,7 +45,25 @@ void do_reset (void) int gpio_init (void) { #ifdef CFG_GPIO_0 - *((unsigned long *)(CFG_GPIO_0_ADDR)) = 0x0; + *((unsigned long *)(CFG_GPIO_0_ADDR)) = 0xFFFFFFFF; #endif return 0; } + +#ifdef CFG_FSL_2 +void fsl_isr2 (void *arg) { + volatile int num; + *((unsigned int *)(CFG_GPIO_0_ADDR + 0x4)) = + ++(*((unsigned int *)(CFG_GPIO_0_ADDR + 0x4))); + GET (num, 2); + NGET (num, 2); + puts("*"); +} + +void fsl_init2 (void) { + puts("fsl_init2\n"); + install_interrupt_handler (FSL_INTR_2,\ + fsl_isr2,\ + NULL); +} +#endif diff --git a/board/xilinx/ml401/xparameters.h b/board/xilinx/ml401/xparameters.h index 18d24f9c1d..1a116ead1b 100644..100755 --- a/board/xilinx/ml401/xparameters.h +++ b/board/xilinx/ml401/xparameters.h @@ -21,47 +21,55 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA * - * * CAUTION: This file is automatically generated by libgen. - * Version: Xilinx EDK 6.3 EDK_Gmm.12.3 + * Version: Xilinx EDK 8.2.02 EDK_Im_Sp2.4 */ /* System Clock Frequency */ -#define XILINX_CLOCK_FREQ 66666667 +#define XILINX_CLOCK_FREQ 100000000 + +/* Microblaze is microblaze_0 */ +#define XILINX_USE_MSR_INSTR 1 +#define XILINX_FSL_NUMBER 3 -/* Interrupt controller is intc_0 */ -#define XILINX_INTC_BASEADDR 0xd1000fc0 -#define XILINX_INTC_NUM_INTR_INPUTS 12 +/* Interrupt controller is opb_intc_0 */ +#define XILINX_INTC_BASEADDR 0x41200000 +#define XILINX_INTC_NUM_INTR_INPUTS 6 -/* Timer pheriphery is opb_timer_0 */ -#define XILINX_TIMER_BASEADDR 0xa2000000 +/* Timer pheriphery is opb_timer_1 */ +#define XILINX_TIMER_BASEADDR 0x41c00000 #define XILINX_TIMER_IRQ 0 -/* Uart pheriphery is console_uart */ -#define XILINX_UART_BASEADDR 0xa0000000 +/* Uart pheriphery is RS232_Uart */ +#define XILINX_UART_BASEADDR 0x40600000 #define XILINX_UART_BAUDRATE 115200 -/* GPIO is opb_gpio_0*/ -#define XILINX_GPIO_BASEADDR 0x90000000 +/* IIC pheriphery is IIC_EEPROM */ +#define XILINX_IIC_0_BASEADDR 0x40800000 +#define XILINX_IIC_0_FREQ 100000 +#define XILINX_IIC_0_BIT 0 + +/* GPIO is LEDs_4Bit*/ +#define XILINX_GPIO_BASEADDR 0x40000000 -/* Flash Memory is opb_emc_0 */ -#define XILINX_FLASH_START 0x28000000 +/* Flash Memory is FLASH_2Mx32 */ +#define XILINX_FLASH_START 0x2c000000 #define XILINX_FLASH_SIZE 0x00800000 -/* Main Memory is plb_ddr_0 */ -#define XILINX_RAM_START 0x10000000 -#define XILINX_RAM_SIZE 0x10000000 +/* Main Memory is DDR_SDRAM_64Mx32 */ +#define XILINX_RAM_START 0x28000000 +#define XILINX_RAM_SIZE 0x04000000 -/* Sysace Controller is opb_sysace_0 */ -#define XILINX_SYSACE_BASEADDR 0xCF000000 -#define XILINX_SYSACE_HIGHADDR 0xCF0001FF +/* Sysace Controller is SysACE_CompactFlash */ +#define XILINX_SYSACE_BASEADDR 0x41800000 +#define XILINX_SYSACE_HIGHADDR 0x4180ffff #define XILINX_SYSACE_MEM_WIDTH 16 -/* Ethernet controller is opb_ethernet_0 */ +/* Ethernet controller is Ethernet_MAC */ #define XPAR_XEMAC_NUM_INSTANCES 1 #define XPAR_OPB_ETHERNET_0_DEVICE_ID 0 -#define XPAR_OPB_ETHERNET_0_BASEADDR 0x60000000 -#define XPAR_OPB_ETHERNET_0_HIGHADDR 0x60003FFF +#define XPAR_OPB_ETHERNET_0_BASEADDR 0x40c00000 +#define XPAR_OPB_ETHERNET_0_HIGHADDR 0x40c0ffff #define XPAR_OPB_ETHERNET_0_DMA_PRESENT 1 #define XPAR_OPB_ETHERNET_0_ERR_COUNT_EXIST 1 #define XPAR_OPB_ETHERNET_0_MII_EXIST 1 |