6 files changed, 11 insertions, 11 deletions
diff --git a/board/denx/m28evk/Kconfig b/board/aries/m28evk/Kconfig
index dd4dc4d096..ab5577cf74 100644
--- a/board/denx/m28evk/Kconfig
+++ b/board/aries/m28evk/Kconfig
@@ -4,7 +4,7 @@ config SYS_BOARD
 	default "m28evk"
 
 config SYS_VENDOR
-	default "denx"
+	default "aries"
 
 config SYS_SOC
 	default "mxs"
diff --git a/board/denx/m28evk/MAINTAINERS b/board/aries/m28evk/MAINTAINERS
index b0535a9186..f600e7d884 100644
--- a/board/denx/m28evk/MAINTAINERS
+++ b/board/aries/m28evk/MAINTAINERS
@@ -1,6 +1,6 @@
 M28EVK BOARD
 M:	Marek Vasut <marek.vasut@gmail.com>
 S:	Maintained
-F:	board/denx/m28evk/
+F:	board/aries/m28evk/
 F:	include/configs/m28evk.h
 F:	configs/m28evk_defconfig
diff --git a/board/denx/m28evk/Makefile b/board/aries/m28evk/Makefile
index 5e890b1eaf..5e890b1eaf 100644
--- a/board/denx/m28evk/Makefile
+++ b/board/aries/m28evk/Makefile
diff --git a/board/denx/m28evk/README b/board/aries/m28evk/README
index cb3ae20f86..9f0d995452 100644
--- a/board/denx/m28evk/README
+++ b/board/aries/m28evk/README
@@ -1,12 +1,12 @@
-DENX M28EVK
-===========
+Aries M28EVK
+============
 
 Files of the M28/M28EVK port
 ----------------------------
 
 arch/arm/cpu/arm926ejs/mxs/	- The CPU support code for the Freescale i.MX28
 arch/arm/include/asm/arch-mxs/	- Header files for the Freescale i.MX28
-board/denx/m28evk/		- M28EVK board specific files
+board/aries/m28evk/		- M28EVK board specific files
 include/configs/m28evk.h	- M28EVK configuration file
 
 Follow the instructions from doc/README.mxs to generate a bootable SD card or to
diff --git a/board/denx/m28evk/m28evk.c b/board/aries/m28evk/m28evk.c
index 33d38cfc54..c990ea9fec 100644
--- a/board/denx/m28evk/m28evk.c
+++ b/board/aries/m28evk/m28evk.c
@@ -1,5 +1,5 @@
 /*
- * DENX M28 module
+ * Aries M28 module
  *
  * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
  * on behalf of DENX Software Engineering GmbH
@@ -93,7 +93,7 @@ int board_mmc_init(bd_t *bis)
 
 int fecmxc_mii_postcall(int phy)
 {
-#if	defined(CONFIG_DENX_M28_V11) || defined(CONFIG_DENX_M28_V10)
+#if	defined(CONFIG_ARIES_M28_V11) || defined(CONFIG_ARIES_M28_V10)
 	/* KZ8031 PHY on old boards. */
 	const uint32_t freq = 0x0080;
 #else
@@ -123,7 +123,7 @@ int board_eth_init(bd_t *bis)
 		CLKCTRL_ENET_TIME_SEL_MASK | CLKCTRL_ENET_CLK_OUT_EN,
 		CLKCTRL_ENET_TIME_SEL_RMII_CLK);
 
-#if !defined(CONFIG_DENX_M28_V11) && !defined(CONFIG_DENX_M28_V10)
+#if !defined(CONFIG_ARIES_M28_V11) && !defined(CONFIG_ARIES_M28_V10)
 	/* Reset the new PHY */
 	gpio_direction_output(MX28_PAD_AUART2_RTS__GPIO_3_11, 0);
 	udelay(10000);
diff --git a/board/denx/m28evk/spl_boot.c b/board/aries/m28evk/spl_boot.c
index 5a1010e595..e27a74e07a 100644
--- a/board/denx/m28evk/spl_boot.c
+++ b/board/aries/m28evk/spl_boot.c
@@ -1,5 +1,5 @@
 /*
- * DENX M28 Boot setup
+ * ARIES M28 Boot setup
  *
  * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
  * on behalf of DENX Software Engineering GmbH
@@ -56,7 +56,7 @@ const iomux_cfg_t iomux_setup[] = {
 	MX28_PAD_LCD_ENABLE__LCD_ENABLE | MUX_CONFIG_LCD,
 
 	/* UART1 */
-#ifdef	CONFIG_DENX_M28_V10
+#ifdef	CONFIG_ARIES_M28_V10
 	MX28_PAD_AUART0_CTS__DUART_RX,
 	MX28_PAD_AUART0_RTS__DUART_TX,
 #else
@@ -132,7 +132,7 @@ const iomux_cfg_t iomux_setup[] = {
 	MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
 	MX28_PAD_ENET0_TXD2__ENET1_TXD0 | MUX_CONFIG_ENET,
 	MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
-#if !defined(CONFIG_DENX_M28_V11) && !defined(CONFIG_DENX_M28_V10)
+#if !defined(CONFIG_ARIES_M28_V11) && !defined(CONFIG_ARIES_M28_V10)
 	MX28_PAD_AUART2_RTS__GPIO_3_11,	/* PHY reset */
 #endif