diff options
Diffstat (limited to 'cmd/Kconfig')
| -rw-r--r-- | cmd/Kconfig | 69 |
1 files changed, 60 insertions, 9 deletions
diff --git a/cmd/Kconfig b/cmd/Kconfig index 38406fcfda..e283cb9a8a 100644 --- a/cmd/Kconfig +++ b/cmd/Kconfig @@ -137,8 +137,6 @@ config AUTOBOOT_STOP_STR_SHA256 endmenu -source "cmd/fastboot/Kconfig" - config BUILD_BIN2C bool @@ -228,7 +226,7 @@ config CMD_BOOTEFI config CMD_BOOTEFI_HELLO_COMPILE bool "Compile a standard EFI hello world binary for testing" - depends on CMD_BOOTEFI && (ARM || X86) + depends on CMD_BOOTEFI && (ARM || X86 || RISCV) default y help This compiles a standard EFI hello world application with U-Boot so @@ -650,6 +648,18 @@ config CMD_DM can be useful to see the state of driver model for debugging or interest. +config CMD_FASTBOOT + bool "fastboot - Android fastboot support" + depends on FASTBOOT + help + This enables the command "fastboot" which enables the Android + fastboot mode for the platform. Fastboot is a protocol for + downloading images, flashing and device control used on + Android devices. Fastboot requires either the network stack + enabled or support for acting as a USB device. + + See doc/README.android-fastboot for more information. + config CMD_FDC bool "fdcboot - Boot from floppy device" help @@ -697,6 +707,13 @@ config CMD_FPGA_LOADP Supports loading an FPGA device from a bitstream buffer containing a partial bitstream. +config CMD_FPGA_LOAD_SECURE + bool "fpga loads - loads secure bitstreams (Xilinx only)" + depends on CMD_FPGA + help + Enables the fpga loads command which is used to load secure + (authenticated or encrypted or both) bitstreams on to FPGA. + config CMD_FPGAD bool "fpgad - dump FPGA registers" help @@ -816,6 +833,21 @@ config CMD_MMC help MMC memory mapped support. +config CMD_MMC_RPMB + bool "Enable support for RPMB in the mmc command" + depends on CMD_MMC + help + Enable the commands for reading, writing and programming the + key for the Replay Protection Memory Block partition in eMMC. + +config CMD_MMC_SWRITE + bool "mmc swrite" + depends on CMD_MMC && MMC_WRITE + select IMAGE_SPARSE + help + Enable support for the "mmc swrite" command to write Android sparse + images to eMMC. + config CMD_NAND bool "nand" default y if NAND_SUNXI @@ -1222,6 +1254,13 @@ config CMD_BMP the image into RAM, then using this command to look at it or display it. +config CMD_BOOTCOUNT + bool "bootcount" + depends on BOOTCOUNT_LIMIT + help + Enable the bootcount command, which allows interrogation and + reset of the bootcounter. + config CMD_BSP bool "Enable board-specific commands" help @@ -1477,25 +1516,37 @@ config HASH_VERIFY help Add -v option to verify data against a hash. +config CMD_TPM_V1 + bool + +config CMD_TPM_V2 + bool + config CMD_TPM bool "Enable the 'tpm' command" - depends on TPM + depends on TPM_V1 || TPM_V2 + select CMD_TPM_V1 if TPM_V1 + select CMD_TPM_V2 if TPM_V2 help This provides a means to talk to a TPM from the command line. A wide range of commands if provided - see 'tpm help' for details. The command requires a suitable TPM on your board and the correct driver must be enabled. +if CMD_TPM + config CMD_TPM_TEST bool "Enable the 'tpm test' command" - depends on CMD_TPM + depends on TPM_V1 help - This provides a a series of tests to confirm that the TPM is working - correctly. The tests cover initialisation, non-volatile RAM, extend, - global lock and checking that timing is within expectations. The - tests pass correctly on Infineon TPMs but may need to be adjusted + This provides a a series of tests to confirm that the TPMv1.x is + working correctly. The tests cover initialisation, non-volatile RAM, + extend, global lock and checking that timing is within expectations. + The tests pass correctly on Infineon TPMs but may need to be adjusted for other devices. +endif + endmenu menu "Firmware commands" |