diff options
Diffstat (limited to 'cpu')
| -rw-r--r-- | cpu/ppc4xx/44x_spd_ddr2.c | 276 | ||||
| -rw-r--r-- | cpu/ppc4xx/4xx_enet.c | 492 | ||||
| -rw-r--r-- | cpu/ppc4xx/4xx_uart.c | 2 | ||||
| -rw-r--r-- | cpu/ppc4xx/Makefile | 13 | ||||
| -rw-r--r-- | cpu/ppc4xx/cpu.c | 41 | ||||
| -rw-r--r-- | cpu/ppc4xx/cpu_init.c | 15 | ||||
| -rw-r--r-- | cpu/ppc4xx/interrupts.c | 237 | ||||
| -rw-r--r-- | cpu/ppc4xx/iop480_uart.c | 1 | ||||
| -rw-r--r-- | cpu/ppc4xx/speed.c | 9 | ||||
| -rw-r--r-- | cpu/ppc4xx/start.S | 19 | ||||
| -rw-r--r-- | cpu/ppc4xx/uic.c | 180 | ||||
| -rw-r--r-- | cpu/ppc4xx/usbdev.c | 4 | ||||
| -rw-r--r-- | cpu/ppc4xx/xilinx_irq.c | 100 |
13 files changed, 694 insertions, 695 deletions
diff --git a/cpu/ppc4xx/44x_spd_ddr2.c b/cpu/ppc4xx/44x_spd_ddr2.c index e9940e8e5b..1c3632428c 100644 --- a/cpu/ppc4xx/44x_spd_ddr2.c +++ b/cpu/ppc4xx/44x_spd_ddr2.c @@ -50,9 +50,19 @@ #include "ecc.h" -#if defined(CONFIG_SPD_EEPROM) && \ - (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT)) +#if defined(CONFIG_SDRAM_PPC4xx_IBM_DDR2) + +#define PPC4xx_IBM_DDR2_DUMP_REGISTER(mnemonic) \ + do { \ + u32 data; \ + mfsdram(SDRAM_##mnemonic, data); \ + printf("%20s[%02x] = 0x%08X\n", \ + "SDRAM_" #mnemonic, SDRAM_##mnemonic, data); \ + } while (0) + +static inline void ppc4xx_ibm_ddr2_register_dump(void); + +#if defined(CONFIG_SPD_EEPROM) /*-----------------------------------------------------------------------------+ * Defines @@ -257,7 +267,6 @@ static void test(void); #else static void DQS_calibration_process(void); #endif -static void ppc440sp_sdram_register_dump(void); int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]); void dcbz_area(u32 start_address, u32 num_bytes); @@ -607,7 +616,7 @@ phys_size_t initdram(int board_type) remove_tlb(0, dram_size); program_tlb(0, 0, dram_size, MY_TLB_WORD2_I_ENABLE); - ppc440sp_sdram_register_dump(); + ppc4xx_ibm_ddr2_register_dump(); /* * Clear potential errors resulting from auto-calibration. @@ -2760,7 +2769,7 @@ calibration_loop: printf("\nERROR: Cannot determine a common read delay for the " "DIMM(s) installed.\n"); debug("%s[%d] ERROR : \n", __FUNCTION__,__LINE__); - ppc440sp_sdram_register_dump(); + ppc4xx_ibm_ddr2_register_dump(); spd_ddr_init_hang (); } @@ -2946,169 +2955,8 @@ static void test(void) } #endif -#if defined(DEBUG) -static void ppc440sp_sdram_register_dump(void) -{ - unsigned int sdram_reg; - unsigned int sdram_data; - unsigned int dcr_data; - - printf("\n Register Dump:\n"); - sdram_reg = SDRAM_MCSTAT; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MCSTAT = 0x%08X", sdram_data); - sdram_reg = SDRAM_MCOPT1; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MCOPT1 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MCOPT2; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MCOPT2 = 0x%08X", sdram_data); - sdram_reg = SDRAM_MODT0; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MODT0 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MODT1; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MODT1 = 0x%08X", sdram_data); - sdram_reg = SDRAM_MODT2; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MODT2 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MODT3; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MODT3 = 0x%08X", sdram_data); - sdram_reg = SDRAM_CODT; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_CODT = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_VVPR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_VVPR = 0x%08X", sdram_data); - sdram_reg = SDRAM_OPARS; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_OPARS = 0x%08X\n", sdram_data); - /* - * OPAR2 is only used as a trigger register. - * No data is contained in this register, and reading or writing - * to is can cause bad things to happen (hangs). Just skip it - * and report NA - * sdram_reg = SDRAM_OPAR2; - * mfsdram(sdram_reg, sdram_data); - * printf(" SDRAM_OPAR2 = 0x%08X\n", sdram_data); - */ - printf(" SDRAM_OPART = N/A "); - sdram_reg = SDRAM_RTR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_RTR = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MB0CF; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MB0CF = 0x%08X", sdram_data); - sdram_reg = SDRAM_MB1CF; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MB1CF = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MB2CF; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MB2CF = 0x%08X", sdram_data); - sdram_reg = SDRAM_MB3CF; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MB3CF = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR0; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR0 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR1; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR1 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR2; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR2 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR3; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR3 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR4; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR4 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR5; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR5 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR6; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR6 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR7; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR7 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR8; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR8 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR9; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR9 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR10; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR10 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR11; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR11 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR12; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR12 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR13; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR13 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_INITPLR14; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR14 = 0x%08X", sdram_data); - sdram_reg = SDRAM_INITPLR15; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_INITPLR15 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_RQDC; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_RQDC = 0x%08X", sdram_data); - sdram_reg = SDRAM_RFDC; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_RFDC = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_RDCC; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_RDCC = 0x%08X", sdram_data); - sdram_reg = SDRAM_DLCR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_DLCR = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_CLKTR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_CLKTR = 0x%08X", sdram_data); - sdram_reg = SDRAM_WRDTR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_WRDTR = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_SDTR1; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_SDTR1 = 0x%08X", sdram_data); - sdram_reg = SDRAM_SDTR2; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_SDTR2 = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_SDTR3; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_SDTR3 = 0x%08X", sdram_data); - sdram_reg = SDRAM_MMODE; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MMODE = 0x%08X\n", sdram_data); - sdram_reg = SDRAM_MEMODE; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_MEMODE = 0x%08X", sdram_data); - sdram_reg = SDRAM_ECCCR; - mfsdram(sdram_reg, sdram_data); - printf(" SDRAM_ECCCR = 0x%08X\n\n", sdram_data); - - dcr_data = mfdcr(SDRAM_R0BAS); - printf(" MQ0_B0BAS = 0x%08X", dcr_data); - dcr_data = mfdcr(SDRAM_R1BAS); - printf(" MQ1_B0BAS = 0x%08X\n", dcr_data); - dcr_data = mfdcr(SDRAM_R2BAS); - printf(" MQ2_B0BAS = 0x%08X", dcr_data); - dcr_data = mfdcr(SDRAM_R3BAS); - printf(" MQ3_B0BAS = 0x%08X\n", dcr_data); -} -#else /* !defined(DEBUG) */ -static void ppc440sp_sdram_register_dump(void) -{ -} -#endif /* defined(DEBUG) */ -#elif defined(CONFIG_405EX) +#else /* CONFIG_SPD_EEPROM */ + /*----------------------------------------------------------------------------- * Function: initdram * Description: Configures the PPC405EX(r) DDR1/DDR2 SDRAM memory @@ -3222,8 +3070,96 @@ phys_size_t initdram(int board_type) #if defined(CONFIG_DDR_ECC) ecc_init(CFG_SDRAM_BASE, CFG_MBYTES_SDRAM << 20); #endif /* defined(CONFIG_DDR_ECC) */ + + ppc4xx_ibm_ddr2_register_dump(); #endif /* !defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */ return (CFG_MBYTES_SDRAM << 20); } -#endif /* defined(CONFIG_SPD_EEPROM) && defined(CONFIG_440SP) || ... */ +#endif /* CONFIG_SPD_EEPROM */ + +static inline void ppc4xx_ibm_ddr2_register_dump(void) +{ +#if defined(DEBUG) + printf("\nPPC4xx IBM DDR2 Register Dump:\n"); + +#if (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT)) + PPC4xx_IBM_DDR2_DUMP_REGISTER(R0BAS); + PPC4xx_IBM_DDR2_DUMP_REGISTER(R1BAS); + PPC4xx_IBM_DDR2_DUMP_REGISTER(R2BAS); + PPC4xx_IBM_DDR2_DUMP_REGISTER(R3BAS); +#endif /* (defined(CONFIG_440SP) || ... */ +#if defined(CONFIG_405EX) + PPC4xx_IBM_DDR2_DUMP_REGISTER(BESR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(BEARL); + PPC4xx_IBM_DDR2_DUMP_REGISTER(BEARH); + PPC4xx_IBM_DDR2_DUMP_REGISTER(WMIRQ); + PPC4xx_IBM_DDR2_DUMP_REGISTER(PLBOPT); + PPC4xx_IBM_DDR2_DUMP_REGISTER(PUABA); +#endif /* defined(CONFIG_405EX) */ + PPC4xx_IBM_DDR2_DUMP_REGISTER(MB0CF); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MB1CF); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MB2CF); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MB3CF); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MCSTAT); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MCOPT1); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MCOPT2); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT0); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT1); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT2); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MODT3); + PPC4xx_IBM_DDR2_DUMP_REGISTER(CODT); +#if (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT)) + PPC4xx_IBM_DDR2_DUMP_REGISTER(VVPR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(OPARS); + /* + * OPART is only used as a trigger register. + * + * No data is contained in this register, and reading or writing + * to is can cause bad things to happen (hangs). Just skip it and + * report "N/A". + */ + printf("%20s = N/A\n", "SDRAM_OPART"); +#endif /* defined(CONFIG_440SP) || ... */ + PPC4xx_IBM_DDR2_DUMP_REGISTER(RTR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR0); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR1); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR2); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR3); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR4); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR5); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR6); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR7); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR8); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR9); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR10); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR11); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR12); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR13); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR14); + PPC4xx_IBM_DDR2_DUMP_REGISTER(INITPLR15); + PPC4xx_IBM_DDR2_DUMP_REGISTER(RQDC); + PPC4xx_IBM_DDR2_DUMP_REGISTER(RFDC); + PPC4xx_IBM_DDR2_DUMP_REGISTER(RDCC); + PPC4xx_IBM_DDR2_DUMP_REGISTER(DLCR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(CLKTR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(WRDTR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(SDTR1); + PPC4xx_IBM_DDR2_DUMP_REGISTER(SDTR2); + PPC4xx_IBM_DDR2_DUMP_REGISTER(SDTR3); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MMODE); + PPC4xx_IBM_DDR2_DUMP_REGISTER(MEMODE); + PPC4xx_IBM_DDR2_DUMP_REGISTER(ECCCR); +#if (defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT)) + PPC4xx_IBM_DDR2_DUMP_REGISTER(CID); +#endif /* defined(CONFIG_440SP) || ... */ + PPC4xx_IBM_DDR2_DUMP_REGISTER(RID); + PPC4xx_IBM_DDR2_DUMP_REGISTER(FCSR); + PPC4xx_IBM_DDR2_DUMP_REGISTER(RTSR); +#endif /* defined(DEBUG) */ +} + +#endif /* CONFIG_SDRAM_PPC4xx_IBM_DDR2 */ diff --git a/cpu/ppc4xx/4xx_enet.c b/cpu/ppc4xx/4xx_enet.c index 4e863dc911..8a3833513e 100644 --- a/cpu/ppc4xx/4xx_enet.c +++ b/cpu/ppc4xx/4xx_enet.c @@ -90,7 +90,6 @@ #include <405_mal.h> #include <miiphy.h> #include <malloc.h> -#include <asm/ppc4xx-intvec.h> /* * Only compile for platform with AMCC EMAC ethernet controller and @@ -122,11 +121,65 @@ * Defines for MAL/EMAC interrupt conditions as reported in the UIC (Universal * Interrupt Controller). *-----------------------------------------------------------------------------*/ -#define MAL_UIC_ERR ( UIC_MAL_SERR | UIC_MAL_TXDE | UIC_MAL_RXDE) -#define MAL_UIC_DEF (UIC_MAL_RXEOB | MAL_UIC_ERR) -#define EMAC_UIC_DEF UIC_ENET -#define EMAC_UIC_DEF1 UIC_ENET1 -#define SEL_UIC_DEF(p) (p ? UIC_ENET1 : UIC_ENET ) +#define ETH_IRQ_NUM(dev) (VECNUM_ETH0 + ((dev) * VECNUM_ETH1_OFFS)) + +#if defined(CONFIG_HAS_ETH3) +#if !defined(CONFIG_440GX) +#define UIC_ETHx (UIC_MASK(ETH_IRQ_NUM(0)) || UIC_MASK(ETH_IRQ_NUM(1)) || \ + UIC_MASK(ETH_IRQ_NUM(2)) || UIC_MASK(ETH_IRQ_NUM(3))) +#else +/* Unfortunately 440GX spreads EMAC interrupts on multiple UIC's */ +#define UIC_ETHx (UIC_MASK(ETH_IRQ_NUM(0)) || UIC_MASK(ETH_IRQ_NUM(1))) +#define UIC_ETHxB (UIC_MASK(ETH_IRQ_NUM(2)) || UIC_MASK(ETH_IRQ_NUM(3))) +#endif /* !defined(CONFIG_440GX) */ +#elif defined(CONFIG_HAS_ETH2) +#define UIC_ETHx (UIC_MASK(ETH_IRQ_NUM(0)) || UIC_MASK(ETH_IRQ_NUM(1)) || \ + UIC_MASK(ETH_IRQ_NUM(2))) +#elif defined(CONFIG_HAS_ETH1) +#define UIC_ETHx (UIC_MASK(ETH_IRQ_NUM(0)) || UIC_MASK(ETH_IRQ_NUM(1))) +#else +#define UIC_ETHx UIC_MASK(ETH_IRQ_NUM(0)) +#endif + +/* + * Define a default version for UIC_ETHxB for non 440GX so that we can + * use common code for all 4xx variants + */ +#if !defined(UIC_ETHxB) +#define UIC_ETHxB 0 +#endif + +#define UIC_MAL_SERR UIC_MASK(VECNUM_MAL_SERR) +#define UIC_MAL_TXDE UIC_MASK(VECNUM_MAL_TXDE) +#define UIC_MAL_RXDE UIC_MASK(VECNUM_MAL_RXDE) +#define UIC_MAL_TXEOB UIC_MASK(VECNUM_MAL_TXEOB) +#define UIC_MAL_RXEOB UIC_MASK(VECNUM_MAL_RXEOB) + +#define MAL_UIC_ERR (UIC_MAL_SERR | UIC_MAL_TXDE | UIC_MAL_RXDE) +#define MAL_UIC_DEF (UIC_MAL_RXEOB | MAL_UIC_ERR) + +/* + * We have 3 different interrupt types: + * - MAL interrupts indicating successful transfer + * - MAL error interrupts indicating MAL related errors + * - EMAC interrupts indicating EMAC related errors + * + * All those interrupts can be on different UIC's, but since + * now at least all interrupts from one type are on the same + * UIC. Only exception is 440GX where the EMAC interrupts are + * spread over two UIC's! + */ +#if defined(CONFIG_440GX) +#define UIC_BASE_MAL UIC1_DCR_BASE +#define UIC_BASE_MAL_ERR UIC2_DCR_BASE +#define UIC_BASE_EMAC UIC2_DCR_BASE +#define UIC_BASE_EMAC_B UIC3_DCR_BASE +#else +#define UIC_BASE_MAL (UIC0_DCR_BASE + (UIC_NR(VECNUM_MAL_TXEOB) * 0x10)) +#define UIC_BASE_MAL_ERR (UIC0_DCR_BASE + (UIC_NR(VECNUM_MAL_SERR) * 0x10)) +#define UIC_BASE_EMAC (UIC0_DCR_BASE + (UIC_NR(ETH_IRQ_NUM(0)) * 0x10)) +#define UIC_BASE_EMAC_B (UIC0_DCR_BASE + (UIC_NR(ETH_IRQ_NUM(0)) * 0x10)) +#endif #undef INFO_4XX_ENET @@ -166,9 +219,6 @@ /*-----------------------------------------------------------------------------+ * Global variables. TX and RX descriptors and buffers. *-----------------------------------------------------------------------------*/ -/* IER globals */ -static uint32_t mal_ier; - #if !defined(CONFIG_NET_MULTI) struct eth_device *emac0_dev = NULL; #endif @@ -200,12 +250,6 @@ struct eth_device *emac0_dev = NULL; #define CONFIG_EMAC_NR_START 0 #endif -#if defined(CONFIG_405EX) || defined(CONFIG_440EPX) -#define ETH_IRQ_NUM(dev) (VECNUM_ETH0 + ((dev))) -#else -#define ETH_IRQ_NUM(dev) (VECNUM_ETH0 + ((dev) * 2)) -#endif - #define MAL_RX_DESC_SIZE 2048 #define MAL_TX_DESC_SIZE 2048 #define MAL_ALLOC_SIZE (MAL_TX_DESC_SIZE + MAL_RX_DESC_SIZE) @@ -465,30 +509,88 @@ int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) #if defined(CONFIG_405EX) int ppc_4xx_eth_setup_bridge(int devnum, bd_t * bis) { - u32 gmiifer = 0; + u32 rgmiifer = 0; /* - * Right now only 2*RGMII is supported. Please extend when needed. - * sr - 2007-09-19 + * The 405EX(r)'s RGMII bridge can operate in one of several + * modes, only one of which (2 x RGMII) allows the + * simultaneous use of both EMACs on the 405EX. */ - switch (1) { - case 1: + + switch (CONFIG_EMAC_PHY_MODE) { + + case EMAC_PHY_MODE_NONE: + /* No ports */ + rgmiifer |= RGMII_FER_DIS << 0; + rgmiifer |= RGMII_FER_DIS << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_NONE; + bis->bi_phymode[1] = BI_PHYMODE_NONE; + break; + case EMAC_PHY_MODE_NONE_RGMII: + /* 1 x RGMII port on channel 0 */ + rgmiifer |= RGMII_FER_RGMII << 0; + rgmiifer |= RGMII_FER_DIS << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_RGMII; + bis->bi_phymode[1] = BI_PHYMODE_NONE; + break; + case EMAC_PHY_MODE_RGMII_NONE: + /* 1 x RGMII port on channel 1 */ + rgmiifer |= RGMII_FER_DIS << 0; + rgmiifer |= RGMII_FER_RGMII << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_NONE; + bis->bi_phymode[1] = BI_PHYMODE_RGMII; + break; + case EMAC_PHY_MODE_RGMII_RGMII: /* 2 x RGMII ports */ - out_be32((void *)RGMII_FER, 0x00000055); + rgmiifer |= RGMII_FER_RGMII << 0; + rgmiifer |= RGMII_FER_RGMII << 4; + out_be32((void *)RGMII_FER, rgmiifer); bis->bi_phymode[0] = BI_PHYMODE_RGMII; bis->bi_phymode[1] = BI_PHYMODE_RGMII; break; - case 2: - /* 2 x SMII ports */ + case EMAC_PHY_MODE_NONE_GMII: + /* 1 x GMII port on channel 0 */ + rgmiifer |= RGMII_FER_GMII << 0; + rgmiifer |= RGMII_FER_DIS << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_GMII; + bis->bi_phymode[1] = BI_PHYMODE_NONE; + break; + case EMAC_PHY_MODE_NONE_MII: + /* 1 x MII port on channel 0 */ + rgmiifer |= RGMII_FER_MII << 0; + rgmiifer |= RGMII_FER_DIS << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_MII; + bis->bi_phymode[1] = BI_PHYMODE_NONE; + break; + case EMAC_PHY_MODE_GMII_NONE: + /* 1 x GMII port on channel 1 */ + rgmiifer |= RGMII_FER_DIS << 0; + rgmiifer |= RGMII_FER_GMII << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_NONE; + bis->bi_phymode[1] = BI_PHYMODE_GMII; + break; + case EMAC_PHY_MODE_MII_NONE: + /* 1 x MII port on channel 1 */ + rgmiifer |= RGMII_FER_DIS << 0; + rgmiifer |= RGMII_FER_MII << 4; + out_be32((void *)RGMII_FER, rgmiifer); + bis->bi_phymode[0] = BI_PHYMODE_NONE; + bis->bi_phymode[1] = BI_PHYMODE_MII; break; default: break; } /* Ensure we setup mdio for this devnum and ONLY this devnum */ - gmiifer = in_be32((void *)RGMII_FER); - gmiifer |= (1 << (19-devnum)); - out_be32((void *)RGMII_FER, gmiifer); + rgmiifer = in_be32((void *)RGMII_FER); + rgmiifer |= (1 << (19-devnum)); + out_be32((void *)RGMII_FER, rgmiifer); return ((int)0x0); } @@ -1377,59 +1479,17 @@ static int ppc_4xx_eth_send (struct eth_device *dev, volatile void *ptr, } } - -#if defined (CONFIG_440) || defined(CONFIG_405EX) - -#if defined(CONFIG_440SP) || defined(CONFIG_440SPE) -/* - * Hack: On 440SP all enet irq sources are located on UIC1 - * Needs some cleanup. --sr - */ -#define UIC0MSR uic1msr -#define UIC0SR uic1sr -#define UIC1MSR uic1msr -#define UIC1SR uic1sr -#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) -/* - * Hack: On 460EX/GT all enet irq sources are located on UIC2 - * Needs some cleanup. --ag - */ -#define UIC0MSR uic2msr -#define UIC0SR uic2sr -#define UIC1MSR uic2msr -#define UIC1SR uic2sr -#else -#define UIC0MSR uic0msr -#define UIC0SR uic0sr -#define UIC1MSR uic1msr -#define UIC1SR uic1sr -#endif - -#if defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_405EX) -#define UICMSR_ETHX uic0msr -#define UICSR_ETHX uic0sr -#elif defined(CONFIG_460EX) || defined(CONFIG_460GT) -#define UICMSR_ETHX uic2msr -#define UICSR_ETHX uic2sr -#else -#define UICMSR_ETHX uic1msr -#define UICSR_ETHX uic1sr -#endif - int enetInt (struct eth_device *dev) { int serviced; int rc = -1; /* default to not us */ - unsigned long mal_isr; - unsigned long emac_isr = 0; - unsigned long mal_rx_eob; - unsigned long my_uic0msr, my_uic1msr; - unsigned long my_uicmsr_ethx; - -#if defined(CONFIG_440GX) - unsigned long my_uic2msr; -#endif + u32 mal_isr; + u32 emac_isr = 0; + u32 mal_eob; + u32 uic_mal; + u32 uic_mal_err; + u32 uic_emac; + u32 uic_emac_b; EMAC_4XX_HW_PST hw_p; /* @@ -1448,256 +1508,79 @@ int enetInt (struct eth_device *dev) do { serviced = 0; - my_uic0msr = mfdcr (UIC0MSR); - my_uic1msr = mfdcr (UIC1MSR); -#if defined(CONFIG_440GX) - my_uic2msr = mfdcr (uic2msr); -#endif - my_uicmsr_ethx = mfdcr (UICMSR_ETHX); + uic_mal = mfdcr(UIC_BASE_MAL + UIC_MSR); + uic_mal_err = mfdcr(UIC_BASE_MAL_ERR + UIC_MSR); + uic_emac = mfdcr(UIC_BASE_EMAC + UIC_MSR); + uic_emac_b = mfdcr(UIC_BASE_EMAC_B + UIC_MSR); - if (!(my_uic0msr & (UIC_MRE | UIC_MTE)) - && !(my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE)) - && !(my_uicmsr_ethx & (UIC_ETH0 | UIC_ETH1))) { - /* not for us */ - return (rc); - } -#if defined (CONFIG_440GX) - if (!(my_uic0msr & (UIC_MRE | UIC_MTE)) - && !(my_uic2msr & (UIC_ETH2 | UIC_ETH3))) { + if (!(uic_mal & (UIC_MAL_RXEOB | UIC_MAL_TXEOB)) + && !(uic_mal_err & (UIC_MAL_SERR | UIC_MAL_TXDE | UIC_MAL_RXDE)) + && !(uic_emac & UIC_ETHx) && !(uic_emac_b & UIC_ETHxB)) { /* not for us */ return (rc); } -#endif + /* get and clear controller status interrupts */ - /* look at Mal and EMAC interrupts */ - if ((my_uic0msr & (UIC_MRE | UIC_MTE)) - || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { - /* we have a MAL interrupt */ - mal_isr = mfdcr (malesr); - /* look for mal error */ - if (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE)) { - mal_err (dev, mal_isr, my_uic1msr, MAL_UIC_DEF, MAL_UIC_ERR); - serviced = 1; - rc = 0; - } - } + /* look at MAL and EMAC error interrupts */ + if (uic_mal_err & (UIC_MAL_SERR | UIC_MAL_TXDE | UIC_MAL_RXDE)) { + /* we have a MAL error interrupt */ + mal_isr = mfdcr(malesr); + mal_err(dev, mal_isr, uic_mal_err, + MAL_UIC_DEF, MAL_UIC_ERR); - /* port by port dispatch of emac interrupts */ - if (hw_p->devnum == 0) { - if (UIC_ETH0 & my_uicmsr_ethx) { /* look for EMAC errors */ - emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); - if ((hw_p->emac_ier & emac_isr) != 0) { - emac_err (dev, emac_isr); - serviced = 1; - rc = 0; - } - } - if ((hw_p->emac_ier & emac_isr) - || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { - mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */ - mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ - mtdcr (UICSR_ETHX, UIC_ETH0); /* Clear */ - return (rc); /* we had errors so get out */ - } - } + /* clear MAL error interrupt status bits */ + mtdcr(UIC_BASE_MAL_ERR + UIC_SR, + UIC_MAL_SERR | UIC_MAL_TXDE | UIC_MAL_RXDE); -#if !defined(CONFIG_440SP) - if (hw_p->devnum == 1) { - if (UIC_ETH1 & my_uicmsr_ethx) { /* look for EMAC errors */ - emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); - if ((hw_p->emac_ier & emac_isr) != 0) { - emac_err (dev, emac_isr); - serviced = 1; - rc = 0; - } - } - if ((hw_p->emac_ier & emac_isr) - || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { - mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */ - mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ - mtdcr (UICSR_ETHX, UIC_ETH1); /* Clear */ - return (rc); /* we had errors so get out */ - } - } -#if defined (CONFIG_440GX) - if (hw_p->devnum == 2) { - if (UIC_ETH2 & my_uic2msr) { /* look for EMAC errors */ - emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); - if ((hw_p->emac_ier & emac_isr) != 0) { - emac_err (dev, emac_isr); - serviced = 1; - rc = 0; - } - } - if ((hw_p->emac_ier & emac_isr) - || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { - mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */ - mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ - mtdcr (uic2sr, UIC_ETH2); - return (rc); /* we had errors so get out */ - } + return -1; } - if (hw_p->devnum == 3) { - if (UIC_ETH3 & my_uic2msr) { /* look for EMAC errors */ - emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); - if ((hw_p->emac_ier & emac_isr) != 0) { - emac_err (dev, emac_isr); - serviced = 1; - rc = 0; - } - } - if ((hw_p->emac_ier & emac_isr) - || (my_uic1msr & (UIC_MS | UIC_MTDE | UIC_MRDE))) { - mtdcr (UIC0SR, UIC_MRE | UIC_MTE); /* Clear */ - mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ - mtdcr (uic2sr, UIC_ETH3); - return (rc); /* we had errors so get out */ - } - } -#endif /* CONFIG_440GX */ -#endif /* !CONFIG_440SP */ + /* look for EMAC errors */ + if ((uic_emac & UIC_ETHx) || (uic_emac_b & UIC_ETHxB)) { + emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); + emac_err(dev, emac_isr); - /* handle MAX TX EOB interrupt from a tx */ - if (my_uic0msr & UIC_MTE) { - mal_rx_eob = mfdcr (maltxeobisr); - mtdcr (maltxeobisr, mal_rx_eob); - mtdcr (UIC0SR, UIC_MTE); - } - /* handle MAL RX EOB interupt from a receive */ - /* check for EOB on valid channels */ - if (my_uic0msr & UIC_MRE) { - mal_rx_eob = mfdcr (malrxeobisr); - if ((mal_rx_eob & - (0x80000000 >> (hw_p->devnum * MAL_RX_CHAN_MUL))) - != 0) { /* call emac routine for channel x */ - /* clear EOB - mtdcr(malrxeobisr, mal_rx_eob); */ - enet_rcv (dev, emac_isr); - /* indicate that we serviced an interrupt */ - serviced = 1; - rc = 0; - } - } + /* clear EMAC error interrupt status bits */ + mtdcr(UIC_BASE_EMAC + UIC_SR, UIC_ETHx); + mtdcr(UIC_BASE_EMAC_B + UIC_SR, UIC_ETHxB); - mtdcr (UIC0SR, UIC_MRE); /* Clear */ - mtdcr (UIC1SR, UIC_MS | UIC_MTDE | UIC_MRDE); /* Clear */ - switch (hw_p->devnum) { - case 0: - mtdcr (UICSR_ETHX, UIC_ETH0); - break; - case 1: - mtdcr (UICSR_ETHX, UIC_ETH1); - break; -#if defined (CONFIG_440GX) - case 2: - mtdcr (uic2sr, UIC_ETH2); - break; - case 3: - mtdcr (uic2sr, UIC_ETH3); - break; -#endif /* CONFIG_440GX */ - default: - break; + return -1; } - } while (serviced); - - return (rc); -} - -#else /* CONFIG_440 */ - -int enetInt (struct eth_device *dev) -{ - int serviced; - int rc = -1; /* default to not us */ - unsigned long mal_isr; - unsigned long emac_isr = 0; - unsigned long mal_rx_eob; - unsigned long my_uicmsr; - - EMAC_4XX_HW_PST hw_p; - - /* - * Because the mal is generic, we need to get the current - * eth device - */ -#if defined(CONFIG_NET_MULTI) - dev = eth_get_dev(); -#else - dev = emac0_dev; -#endif - - hw_p = dev->priv; - - /* enter loop that stays in interrupt code until nothing to service */ - do { - serviced = 0; - my_uicmsr = mfdcr (uicmsr); - - if ((my_uicmsr & (MAL_UIC_DEF | EMAC_UIC_DEF)) == 0) { /* not for us */ - return (rc); - } - /* get and clear controller status interrupts */ - /* look at Mal and EMAC interrupts */ - if ((MAL_UIC_DEF & my_uicmsr) != 0) { /* we have a MAL interrupt */ - mal_isr = mfdcr (malesr); - /* look for mal error */ - if ((my_uicmsr & MAL_UIC_ERR) != 0) { - mal_err (dev, mal_isr, my_uicmsr, MAL_UIC_DEF, MAL_UIC_ERR); - serviced = 1; - rc = 0; - } + /* handle MAX TX EOB interrupt from a tx */ + if (uic_mal & UIC_MAL_TXEOB) { + /* clear MAL interrupt status bits */ + mal_eob = mfdcr(maltxeobisr); + mtdcr(maltxeobisr, mal_eob); + mtdcr(UIC_BASE_MAL + UIC_SR, UIC_MAL_TXEOB); + + /* indicate that we serviced an interrupt */ + serviced = 1; + rc = 0; } - /* port by port dispatch of emac interrupts */ + /* handle MAL RX EOB interupt from a receive */ + /* check for EOB on valid channels */ + if (uic_mal & UIC_MAL_RXEOB) { + mal_eob = mfdcr(malrxeobisr); + if (mal_eob & + (0x80000000 >> (hw_p->devnum * MAL_RX_CHAN_MUL))) { + /* push packet to upper layer */ + enet_rcv(dev, emac_isr); - if ((SEL_UIC_DEF(hw_p->devnum) & my_uicmsr) != 0) { /* look for EMAC errors */ - emac_isr = in_be32((void *)EMAC_ISR + hw_p->hw_addr); - if ((hw_p->emac_ier & emac_isr) != 0) { - emac_err (dev, emac_isr); - serviced = 1; - rc = 0; - } - } - if (((hw_p->emac_ier & emac_isr) != 0) || ((MAL_UIC_ERR & my_uicmsr) != 0)) { - mtdcr (uicsr, MAL_UIC_DEF | SEL_UIC_DEF(hw_p->devnum)); /* Clear */ - return (rc); /* we had errors so get out */ - } + /* clear MAL interrupt status bits */ + mtdcr(UIC_BASE_MAL + UIC_SR, UIC_MAL_RXEOB); - /* handle MAX TX EOB interrupt from a tx */ - if (my_uicmsr & UIC_MAL_TXEOB) { - mal_rx_eob = mfdcr (maltxeobisr); - mtdcr (maltxeobisr, mal_rx_eob); - mtdcr (uicsr, UIC_MAL_TXEOB); - } - /* handle MAL RX EOB interupt from a receive */ - /* check for EOB on valid channels */ - if (my_uicmsr & UIC_MAL_RXEOB) - { - mal_rx_eob = mfdcr (malrxeobisr); - if ((mal_rx_eob & (0x80000000 >> hw_p->devnum)) != 0) { /* call emac routine for channel x */ - /* clear EOB - mtdcr(malrxeobisr, mal_rx_eob); */ - enet_rcv (dev, emac_isr); /* indicate that we serviced an interrupt */ serviced = 1; rc = 0; } } - mtdcr (uicsr, MAL_UIC_DEF|EMAC_UIC_DEF|EMAC_UIC_DEF1); /* Clear */ -#if defined(CONFIG_405EZ) - mtsdr (sdricintstat, SDR_ICRX_STAT | SDR_ICTX0_STAT | SDR_ICTX1_STAT); -#endif /* defined(CONFIG_405EZ) */ - } - while (serviced); + } while (serviced); return (rc); } -#endif /* CONFIG_440 */ - /*-----------------------------------------------------------------------------+ * MAL Error Routine *-----------------------------------------------------------------------------*/ @@ -1883,6 +1766,7 @@ int ppc_4xx_eth_initialize (bd_t * bis) EMAC_4XX_HW_PST hw = NULL; u8 ethaddr[4 + CONFIG_EMAC_NR_START][6]; u32 hw_addr[4]; + u32 mal_ier; #if defined(CONFIG_440GX) unsigned long pfc1; @@ -2020,19 +1904,19 @@ int ppc_4xx_eth_initialize (bd_t * bis) mtdcr (malier, mal_ier); /* install MAL interrupt handler */ - irq_install_handler (VECNUM_MS, + irq_install_handler (VECNUM_MAL_SERR, (interrupt_handler_t *) enetInt, dev); - irq_install_handler (VECNUM_MTE, + irq_install_handler (VECNUM_MAL_TXEOB, (interrupt_handler_t *) enetInt, dev); - irq_install_handler (VECNUM_MRE, + irq_install_handler (VECNUM_MAL_RXEOB, (interrupt_handler_t *) enetInt, dev); - irq_install_handler (VECNUM_TXDE, + irq_install_handler (VECNUM_MAL_TXDE, (interrupt_handler_t *) enetInt, dev); - irq_install_handler (VECNUM_RXDE, + irq_install_handler (VECNUM_MAL_RXDE, (interrupt_handler_t *) enetInt, dev); virgin = 1; diff --git a/cpu/ppc4xx/4xx_uart.c b/cpu/ppc4xx/4xx_uart.c index a7587d4351..766e586808 100644 --- a/cpu/ppc4xx/4xx_uart.c +++ b/cpu/ppc4xx/4xx_uart.c @@ -46,7 +46,7 @@ #include <asm/processor.h> #include <asm/io.h> #include <watchdog.h> -#include <asm/ppc4xx-intvec.h> +#include <ppc4xx.h> #ifdef CONFIG_SERIAL_MULTI #include <serial.h> diff --git a/cpu/ppc4xx/Makefile b/cpu/ppc4xx/Makefile index 800bb41d01..c773400a5d 100644 --- a/cpu/ppc4xx/Makefile +++ b/cpu/ppc4xx/Makefile @@ -35,10 +35,8 @@ SOBJS += kgdb.o COBJS := 40x_spd_sdram.o COBJS += 44x_spd_ddr.o COBJS += 44x_spd_ddr2.o -COBJS += 4xx_enet.o COBJS += 4xx_pci.o COBJS += 4xx_pcie.o -COBJS += 4xx_uart.o COBJS += bedbug_405.o COBJS += commproc.o COBJS += cpu.o @@ -47,11 +45,9 @@ COBJS += denali_data_eye.o COBJS += denali_spd_ddr2.o COBJS += ecc.o COBJS += fdt.o -COBJS += gpio.o COBJS += i2c.o COBJS += interrupts.o COBJS += iop480_uart.o -COBJS += miiphy.o COBJS += ndfc.o COBJS += sdram.o COBJS += speed.o @@ -60,6 +56,15 @@ COBJS += traps.o COBJS += usb.o COBJS += usb_ohci.o COBJS += usbdev.o +ifndef CONFIG_XILINX_440 +COBJS += 4xx_enet.o +COBJS += 4xx_uart.o +COBJS += gpio.o +COBJS += miiphy.o +COBJS += uic.o +else +COBJS += xilinx_irq.o +endif SRCS := $(START:.o=.S) $(SOBJS:.o=.S) $(COBJS:.o=.c) OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS)) diff --git a/cpu/ppc4xx/cpu.c b/cpu/ppc4xx/cpu.c index 39f439df98..bc9335a05e 100644 --- a/cpu/ppc4xx/cpu.c +++ b/cpu/ppc4xx/cpu.c @@ -184,6 +184,19 @@ static char *bootstrap_str[] = { static char bootstrap_char[] = { 'A', 'B', 'C', 'D', 'E', 'G', 'F', 'H' }; #endif +#if defined(CONFIG_460SX) +#define SDR0_PINSTP_SHIFT 29 +static char *bootstrap_str[] = { + "EBC (8 bits)", + "EBC (16 bits)", + "EBC (32 bits)", + "NAND (8 bits)", + "I2C (Addr 0x54)", /* A8 */ + "I2C (Addr 0x52)", /* A4 */ +}; +static char bootstrap_char[] = { 'A', 'B', 'C', 'D', 'E', 'G' }; +#endif + #if defined(CONFIG_405EZ) #define SDR0_PINSTP_SHIFT 28 static char *bootstrap_str[] = { @@ -266,7 +279,11 @@ int checkcpu (void) get_sys_info(&sys_info); +#if defined(CONFIG_XILINX_440) + puts("IBM PowerPC 4"); +#else puts("AMCC PowerPC 4"); +#endif #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \ defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \ @@ -509,6 +526,30 @@ int checkcpu (void) strcpy(addstr, "Security/Kasumi support"); break; + case PVR_460SX_RA: + puts("SX Rev. A"); + strcpy(addstr, "Security support"); + break; + + case PVR_460SX_RA_V1: + puts("SX Rev. A"); + strcpy(addstr, "No Security support"); + break; + + case PVR_460GX_RA: + puts("GX Rev. A"); + strcpy(addstr, "Security support"); + break; + + case PVR_460GX_RA_V1: + puts("GX Rev. A"); + strcpy(addstr, "No Security support"); + break; + + case PVR_VIRTEX5: + puts("x5 VIRTEX5"); + break; + default: printf (" UNKNOWN (PVR=%08x)", pvr); break; diff --git a/cpu/ppc4xx/cpu_init.c b/cpu/ppc4xx/cpu_init.c index ac64279051..e2d0402781 100644 --- a/cpu/ppc4xx/cpu_init.c +++ b/cpu/ppc4xx/cpu_init.c @@ -138,9 +138,10 @@ void reconfigure_pll(u32 new_cpu_freq) void cpu_init_f (void) { -#if defined(CONFIG_WATCHDOG) || defined(CONFIG_460EX) +#if defined(CONFIG_WATCHDOG) || defined(CONFIG_440GX) || defined(CONFIG_460EX) u32 val; #endif + reconfigure_pll(CFG_PLL_RECONFIG); #if (defined(CONFIG_405EP) || defined (CONFIG_405EX)) && !defined(CFG_4xx_GPIO_TABLE) @@ -273,6 +274,18 @@ cpu_init_f (void) reset_4xx_watchdog(); #endif /* CONFIG_WATCHDOG */ +#if defined(CONFIG_440GX) + /* Take the GX out of compatibility mode + * Travis Sawyer, 9 Mar 2004 + * NOTE: 440gx user manual inconsistency here + * Compatibility mode and Ethernet Clock select are not + * correct in the manual + */ + mfsdr(sdr_mfr, val); + val &= ~0x10000000; + mtsdr(sdr_mfr,val); +#endif /* CONFIG_440GX */ + #if defined(CONFIG_460EX) /* * Set SDR0_AHB_CFG[A2P_INCR4] (bit 24) and diff --git a/cpu/ppc4xx/interrupts.c b/cpu/ppc4xx/interrupts.c index 8620e2b484..494bd8c9ef 100644 --- a/cpu/ppc4xx/interrupts.c +++ b/cpu/ppc4xx/interrupts.c @@ -8,6 +8,10 @@ * (C) Copyright 2003 (440GX port) * Travis B. Sawyer, Sandburst Corporation, tsawyer@sandburst.com * + * (C) Copyright 2008 (PPC440X05 port for Virtex 5 FX) + * Ricardo Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * Work supported by Qtechnology (htpp://qtec.com) + * * See file CREDITS for list of people who contributed to this * project. * @@ -31,31 +35,14 @@ #include <watchdog.h> #include <command.h> #include <asm/processor.h> +#include <asm/interrupt.h> #include <ppc4xx.h> #include <ppc_asm.tmpl> #include <commproc.h> -#include <asm/ppc4xx-intvec.h> DECLARE_GLOBAL_DATA_PTR; /* - * Define the number of UIC's - */ -#if defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) -#define UIC_MAX 4 -#elif defined(CONFIG_440GX) || \ - defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ - defined(CONFIG_405EX) -#define UIC_MAX 3 -#elif defined(CONFIG_440GP) || defined(CONFIG_440SP) || \ - defined(CONFIG_440EP) || defined(CONFIG_440GR) -#define UIC_MAX 2 -#else -#define UIC_MAX 1 -#endif - -/* * CPM interrupt vector functions. */ struct irq_action { @@ -63,15 +50,7 @@ struct irq_action { void *arg; int count; }; - -static struct irq_action irq_vecs[UIC_MAX * 32]; - -u32 get_dcr(u16); -void set_dcr(u16, u32); - -#if (UIC_MAX > 1) && !defined(CONFIG_440GX) -static void uic_cascade_interrupt(void *para); -#endif +static struct irq_action irq_vecs[IRQ_MAX]; #if defined(CONFIG_440) @@ -112,7 +91,7 @@ int interrupt_init_cpu (unsigned *decrementer_count) /* * Mark all irqs as free */ - for (vec = 0; vec < (UIC_MAX * 32); vec++) { + for (vec = 0; vec < IRQ_MAX; vec++) { irq_vecs[vec].handler = NULL; irq_vecs[vec].arg = NULL; irq_vecs[vec].count = 0; @@ -156,160 +135,38 @@ int interrupt_init_cpu (unsigned *decrementer_count) */ set_evpr(0x00000000); -#if !defined(CONFIG_440GX) -#if (UIC_MAX > 1) - /* Install the UIC1 handlers */ - irq_install_handler(VECNUM_UIC1NC, uic_cascade_interrupt, 0); - irq_install_handler(VECNUM_UIC1C, uic_cascade_interrupt, 0); -#endif -#if (UIC_MAX > 2) - irq_install_handler(VECNUM_UIC2NC, uic_cascade_interrupt, 0); - irq_install_handler(VECNUM_UIC2C, uic_cascade_interrupt, 0); -#endif -#if (UIC_MAX > 3) - irq_install_handler(VECNUM_UIC3NC, uic_cascade_interrupt, 0); - irq_install_handler(VECNUM_UIC3C, uic_cascade_interrupt, 0); -#endif -#else /* !defined(CONFIG_440GX) */ - /* Take the GX out of compatibility mode - * Travis Sawyer, 9 Mar 2004 - * NOTE: 440gx user manual inconsistency here - * Compatibility mode and Ethernet Clock select are not - * correct in the manual + /* + * Call uic or xilinx_irq pic_enable */ - mfsdr(sdr_mfr, val); - val &= ~0x10000000; - mtsdr(sdr_mfr,val); - - /* Enable UIC interrupts via UIC Base Enable Register */ - mtdcr(uicb0sr, UICB0_ALL); - mtdcr(uicb0er, 0x54000000); - /* None are critical */ - mtdcr(uicb0cr, 0); -#endif /* !defined(CONFIG_440GX) */ + pic_enable(); return (0); } -/* Handler for UIC interrupt */ -static void uic_interrupt(u32 uic_base, int vec_base) +void timer_interrupt_cpu(struct pt_regs *regs) { - u32 uic_msr; - u32 msr_shift; - int vec; - - /* - * Read masked interrupt status register to determine interrupt source - */ - uic_msr = get_dcr(uic_base + UIC_MSR); - msr_shift = uic_msr; - vec = vec_base; - - while (msr_shift != 0) { - if (msr_shift & 0x80000000) { - /* - * Increment irq counter (for debug purpose only) - */ - irq_vecs[vec].count++; - - if (irq_vecs[vec].handler != NULL) { - /* call isr */ - (*irq_vecs[vec].handler)(irq_vecs[vec].arg); - } else { - set_dcr(uic_base + UIC_ER, - get_dcr(uic_base + UIC_ER) & - ~(0x80000000 >> (vec & 0x1f))); - printf("Masking bogus interrupt vector %d" - " (UIC_BASE=0x%x)\n", vec, uic_base); - } - - /* - * After servicing the interrupt, we have to remove the - * status indicator - */ - set_dcr(uic_base + UIC_SR, (0x80000000 >> (vec & 0x1f))); - } - - /* - * Shift msr to next position and increment vector - */ - msr_shift <<= 1; - vec++; - } + /* nothing to do here */ + return; } -#if (UIC_MAX > 1) && !defined(CONFIG_440GX) -static void uic_cascade_interrupt(void *para) +void interrupt_run_handler(int vec) { - external_interrupt(para); -} -#endif - -#if defined(CONFIG_440) -#if defined(CONFIG_440GX) -/* 440GX uses base uic register */ -#define UIC_BMSR uicb0msr -#define UIC_BSR uicb0sr -#else -#define UIC_BMSR uic0msr -#define UIC_BSR uic0sr -#endif -#else /* CONFIG_440 */ -#define UIC_BMSR uicmsr -#define UIC_BSR uicsr -#endif /* CONFIG_440 */ - -/* - * Handle external interrupts - */ -void external_interrupt(struct pt_regs *regs) -{ - u32 uic_msr; - - /* - * Read masked interrupt status register to determine interrupt source - */ - uic_msr = mfdcr(UIC_BMSR); - -#if (UIC_MAX > 1) - if ((UICB0_UIC1CI & uic_msr) || (UICB0_UIC1NCI & uic_msr)) - uic_interrupt(UIC1_DCR_BASE, 32); -#endif - -#if (UIC_MAX > 2) - if ((UICB0_UIC2CI & uic_msr) || (UICB0_UIC2NCI & uic_msr)) - uic_interrupt(UIC2_DCR_BASE, 64); -#endif - -#if (UIC_MAX > 3) - if ((UICB0_UIC3CI & uic_msr) || (UICB0_UIC3NCI & uic_msr)) - uic_interrupt(UIC3_DCR_BASE, 96); -#endif - -#if defined(CONFIG_440) -#if !defined(CONFIG_440GX) - if (uic_msr & ~(UICB0_ALL)) - uic_interrupt(UIC0_DCR_BASE, 0); -#else - if ((UICB0_UIC0CI & uic_msr) || (UICB0_UIC0NCI & uic_msr)) - uic_interrupt(UIC0_DCR_BASE, 0); -#endif -#else /* CONFIG_440 */ - uic_interrupt(UIC0_DCR_BASE, 0); -#endif /* CONFIG_440 */ - - mtdcr(UIC_BSR, uic_msr); + irq_vecs[vec].count++; + + if (irq_vecs[vec].handler != NULL) { + /* call isr */ + (*irq_vecs[vec].handler) (irq_vecs[vec].arg); + } else { + pic_irq_disable(vec); + printf("Masking bogus interrupt vector %d\n", vec); + } + pic_irq_ack(vec); return; } -/* - * Install and free a interrupt handler. - */ void irq_install_handler(int vec, interrupt_handler_t * handler, void *arg) { - int i; - /* * Print warning when replacing with a different irq vector */ @@ -320,55 +177,19 @@ void irq_install_handler(int vec, interrupt_handler_t * handler, void *arg) irq_vecs[vec].handler = handler; irq_vecs[vec].arg = arg; - i = vec & 0x1f; - if ((vec >= 0) && (vec < 32)) - mtdcr(uicer, mfdcr(uicer) | (0x80000000 >> i)); -#if (UIC_MAX > 1) - else if ((vec >= 32) && (vec < 64)) - mtdcr(uic1er, mfdcr(uic1er) | (0x80000000 >> i)); -#endif -#if (UIC_MAX > 2) - else if ((vec >= 64) && (vec < 96)) - mtdcr(uic2er, mfdcr(uic2er) | (0x80000000 >> i)); -#endif -#if (UIC_MAX > 3) - else if (vec >= 96) - mtdcr(uic3er, mfdcr(uic3er) | (0x80000000 >> i)); -#endif - - debug("Install interrupt for vector %d ==> %p\n", vec, handler); + pic_irq_enable(vec); + return; } -void irq_free_handler (int vec) +void irq_free_handler(int vec) { - int i; - debug("Free interrupt for vector %d ==> %p\n", vec, irq_vecs[vec].handler); - i = vec & 0x1f; - if ((vec >= 0) && (vec < 32)) - mtdcr(uicer, mfdcr(uicer) & ~(0x80000000 >> i)); -#if (UIC_MAX > 1) - else if ((vec >= 32) && (vec < 64)) - mtdcr(uic1er, mfdcr(uic1er) & ~(0x80000000 >> i)); -#endif -#if (UIC_MAX > 2) - else if ((vec >= 64) && (vec < 96)) - mtdcr(uic2er, mfdcr(uic2er) & ~(0x80000000 >> i)); -#endif -#if (UIC_MAX > 3) - else if (vec >= 96) - mtdcr(uic3er, mfdcr(uic3er) & ~(0x80000000 >> i)); -#endif + pic_irq_disable(vec); irq_vecs[vec].handler = NULL; irq_vecs[vec].arg = NULL; -} - -void timer_interrupt_cpu (struct pt_regs *regs) -{ - /* nothing to do here */ return; } @@ -380,7 +201,7 @@ int do_irqinfo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) printf ("Interrupt-Information:\n"); printf ("Nr Routine Arg Count\n"); - for (vec = 0; vec < (UIC_MAX * 32); vec++) { + for (vec = 0; vec < IRQ_MAX; vec++) { if (irq_vecs[vec].handler != NULL) { printf ("%02d %08lx %08lx %d\n", vec, diff --git a/cpu/ppc4xx/iop480_uart.c b/cpu/ppc4xx/iop480_uart.c index 3af0767c55..0e3423f7ab 100644 --- a/cpu/ppc4xx/iop480_uart.c +++ b/cpu/ppc4xx/iop480_uart.c @@ -26,7 +26,6 @@ #include <asm/processor.h> #include <asm/io.h> #include <watchdog.h> -#include <asm/ppc4xx-intvec.h> #ifdef CONFIG_SERIAL_MULTI #include <serial.h> diff --git a/cpu/ppc4xx/speed.c b/cpu/ppc4xx/speed.c index 34bd7214e7..d21bd82dc6 100644 --- a/cpu/ppc4xx/speed.c +++ b/cpu/ppc4xx/speed.c @@ -205,7 +205,8 @@ ulong get_PCI_freq (void) #elif defined(CONFIG_440) -#if defined(CONFIG_460EX) || defined(CONFIG_460GT) +#if defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) static u8 pll_fwdv_multi_bits[] = { /* values for: 1 - 16 */ 0x00, 0x01, 0x0f, 0x04, 0x09, 0x0a, 0x0d, 0x0e, 0x03, 0x0c, @@ -415,7 +416,8 @@ ulong get_PCI_freq (void) return sys_info.freqPCI; } -#elif !defined(CONFIG_440GX) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) +#elif !defined(CONFIG_440GX) && !defined(CONFIG_440SP) && !defined(CONFIG_440SPE) \ + && !defined(CONFIG_XILINX_440) void get_sys_info (sys_info_t * sysInfo) { unsigned long strp0; @@ -448,6 +450,8 @@ void get_sys_info (sys_info_t * sysInfo) sysInfo->freqUART = sysInfo->freqPLB; } #else + +#if !defined(CONFIG_XILINX_440) void get_sys_info (sys_info_t * sysInfo) { unsigned long strp0; @@ -534,6 +538,7 @@ void get_sys_info (sys_info_t * sysInfo) } #endif +#endif /* CONFIG_XILINX_440 */ #if defined(CONFIG_YUCCA) unsigned long determine_sysper(void) diff --git a/cpu/ppc4xx/start.S b/cpu/ppc4xx/start.S index 426bf3c6f9..97411bdb9d 100644 --- a/cpu/ppc4xx/start.S +++ b/cpu/ppc4xx/start.S @@ -677,7 +677,8 @@ _start: /* not all PPC's have internal SRAM usable as L2-cache */ #if defined(CONFIG_440GX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) + defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) mtdcr l2_cache_cfg,r0 /* Ensure L2 Cache is off */ #endif @@ -720,6 +721,19 @@ _start: lis r1,0x4000 /* BAS = 8000_0000 */ ori r1,r1,0x4580 /* 16k */ mtdcr isram0_sb0cr,r1 +#elif defined(CONFIG_460SX) + lis r1,0x0000 /* BAS = 0000_0000 */ + ori r1,r1,0x0B84 /* first 128k */ + mtdcr isram0_sb0cr,r1 + lis r1,0x0001 + ori r1,r1,0x0B84 /* second 128k */ + mtdcr isram0_sb1cr,r1 + lis r1, 0x0002 + ori r1,r1, 0x0B84 /* third 128k */ + mtdcr isram0_sb2cr,r1 + lis r1, 0x0003 + ori r1,r1, 0x0B84 /* fourth 128k */ + mtdcr isram0_sb3cr,r1 #elif defined(CONFIG_440GP) ori r1,r1,0x0380 /* 8k rw */ mtdcr isram0_sb0cr,r1 @@ -1415,7 +1429,8 @@ relocate_code: #if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \ defined(CONFIG_440EPX) || defined(CONFIG_440GRX) || \ defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \ - defined(CONFIG_460EX) || defined(CONFIG_460GT) + defined(CONFIG_460EX) || defined(CONFIG_460GT) || \ + defined(CONFIG_460SX) /* * On some 440er platforms the cache is enabled in the first TLB (Boot-CS) * to speed up the boot process. Now this cache needs to be disabled. diff --git a/cpu/ppc4xx/uic.c b/cpu/ppc4xx/uic.c new file mode 100644 index 0000000000..7944c6c3c2 --- /dev/null +++ b/cpu/ppc4xx/uic.c @@ -0,0 +1,180 @@ +/* + * (C) Copyright 2000-2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2002 (440 port) + * Scott McNutt, Artesyn Communication Producs, smcnutt@artsyncp.com + * + * (C) Copyright 2003 (440GX port) + * Travis B. Sawyer, Sandburst Corporation, tsawyer@sandburst.com + * + * (C) Copyright 2008 (PPC440X05 port for Virtex 5 FX) + * Ricardo Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * Work supported by Qtechnology (htpp://qtec.com) + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <watchdog.h> +#include <command.h> +#include <asm/processor.h> +#include <asm/interrupt.h> +#include <ppc4xx.h> +#include <ppc_asm.tmpl> +#include <commproc.h> + +#if (UIC_MAX > 3) +#define UICB0_ALL (UIC_MASK(VECNUM_UIC1CI) | UIC_MASK(VECNUM_UIC1NCI) | \ + UIC_MASK(VECNUM_UIC2CI) | UIC_MASK(VECNUM_UIC2NCI) | \ + UIC_MASK(VECNUM_UIC3CI) | UIC_MASK(VECNUM_UIC3NCI)) +#elif (UIC_MAX > 2) +#define UICB0_ALL (UIC_MASK(VECNUM_UIC1CI) | UIC_MASK(VECNUM_UIC1NCI) | \ + UIC_MASK(VECNUM_UIC2CI) | UIC_MASK(VECNUM_UIC2NCI)) +#elif (UIC_MAX > 1) +#define UICB0_ALL (UIC_MASK(VECNUM_UIC1CI) | UIC_MASK(VECNUM_UIC1NCI)) +#else +#define UICB0_ALL 0 +#endif + +u32 get_dcr(u16); + +DECLARE_GLOBAL_DATA_PTR; + +void pic_enable(void) +{ +#if (UIC_MAX > 1) + /* Install the UIC1 handlers */ + irq_install_handler(VECNUM_UIC1NCI, (void *)(void *)external_interrupt, 0); + irq_install_handler(VECNUM_UIC1CI, (void *)(void *)external_interrupt, 0); +#endif +#if (UIC_MAX > 2) + irq_install_handler(VECNUM_UIC2NCI, (void *)(void *)external_interrupt, 0); + irq_install_handler(VECNUM_UIC2CI, (void *)(void *)external_interrupt, 0); +#endif +#if (UIC_MAX > 3) + irq_install_handler(VECNUM_UIC3NCI, (void *)(void *)external_interrupt, 0); + irq_install_handler(VECNUM_UIC3CI, (void *)(void *)external_interrupt, 0); +#endif +} + +/* Handler for UIC interrupt */ +static void uic_interrupt(u32 uic_base, int vec_base) +{ + u32 uic_msr; + u32 msr_shift; + int vec; + + /* + * Read masked interrupt status register to determine interrupt source + */ + uic_msr = get_dcr(uic_base + UIC_MSR); + msr_shift = uic_msr; + vec = vec_base; + + while (msr_shift != 0) { + if (msr_shift & 0x80000000) + interrupt_run_handler(vec); + /* + * Shift msr to next position and increment vector + */ + msr_shift <<= 1; + vec++; + } +} + +/* + * Handle external interrupts + */ +void external_interrupt(struct pt_regs *regs) +{ + u32 uic_msr; + + /* + * Read masked interrupt status register to determine interrupt source + */ + uic_msr = mfdcr(uic0msr); + +#if (UIC_MAX > 1) + if ((UIC_MASK(VECNUM_UIC1CI) & uic_msr) || + (UIC_MASK(VECNUM_UIC1NCI) & uic_msr)) + uic_interrupt(UIC1_DCR_BASE, 32); +#endif + +#if (UIC_MAX > 2) + if ((UIC_MASK(VECNUM_UIC2CI) & uic_msr) || + (UIC_MASK(VECNUM_UIC2NCI) & uic_msr)) + uic_interrupt(UIC2_DCR_BASE, 64); +#endif + +#if (UIC_MAX > 3) + if ((UIC_MASK(VECNUM_UIC3CI) & uic_msr) || + (UIC_MASK(VECNUM_UIC3NCI) & uic_msr)) + uic_interrupt(UIC3_DCR_BASE, 96); +#endif + + if (uic_msr & ~(UICB0_ALL)) + uic_interrupt(UIC0_DCR_BASE, 0); + + mtdcr(uic0sr, uic_msr); + + return; +} + +void pic_irq_ack(unsigned int vec) +{ + if ((vec >= 0) && (vec < 32)) + mtdcr(uicsr, UIC_MASK(vec)); + else if ((vec >= 32) && (vec < 64)) + mtdcr(uic1sr, UIC_MASK(vec)); + else if ((vec >= 64) && (vec < 96)) + mtdcr(uic2sr, UIC_MASK(vec)); + else if (vec >= 96) + mtdcr(uic3sr, UIC_MASK(vec)); +} + +/* + * Install and free a interrupt handler. + */ +void pic_irq_enable(unsigned int vec) +{ + + if ((vec >= 0) && (vec < 32)) + mtdcr(uicer, mfdcr(uicer) | UIC_MASK(vec)); + else if ((vec >= 32) && (vec < 64)) + mtdcr(uic1er, mfdcr(uic1er) | UIC_MASK(vec)); + else if ((vec >= 64) && (vec < 96)) + mtdcr(uic2er, mfdcr(uic2er) | UIC_MASK(vec)); + else if (vec >= 96) + mtdcr(uic3er, mfdcr(uic3er) | UIC_MASK(vec)); + + debug("Install interrupt for vector %d ==> %p\n", vec, handler); +} + +void pic_irq_disable(unsigned int vec) +{ + if ((vec >= 0) && (vec < 32)) + mtdcr(uicer, mfdcr(uicer) & ~UIC_MASK(vec)); + else if ((vec >= 32) && (vec < 64)) + mtdcr(uic1er, mfdcr(uic1er) & ~UIC_MASK(vec)); + else if ((vec >= 64) && (vec < 96)) + mtdcr(uic2er, mfdcr(uic2er) & ~UIC_MASK(vec)); + else if (vec >= 96) + mtdcr(uic3er, mfdcr(uic3er) & ~UIC_MASK(vec)); +} diff --git a/cpu/ppc4xx/usbdev.c b/cpu/ppc4xx/usbdev.c index d71ba7710a..faf7f0878f 100644 --- a/cpu/ppc4xx/usbdev.c +++ b/cpu/ppc4xx/usbdev.c @@ -6,8 +6,8 @@ #if (defined(CONFIG_440EP) || defined(CONFIG_440EPX)) && defined(CONFIG_CMD_USB) #include <usb.h> +#include <asm/ppc4xx-uic.h> #include "usbdev.h" -#include <asm/ppc4xx-intvec.h> #define USB_DT_DEVICE 0x01 #define USB_DT_CONFIG 0x02 @@ -197,7 +197,7 @@ void usb_dev_init() /*enable interrupts */ *(unsigned char *)USB2D0_INTRUSBE_8 = 0x0f; - irq_install_handler(VECNUM_HSB2D, (interrupt_handler_t *) usbInt, + irq_install_handler(VECNUM_USBDEV, (interrupt_handler_t *) usbInt, NULL); } #else diff --git a/cpu/ppc4xx/xilinx_irq.c b/cpu/ppc4xx/xilinx_irq.c new file mode 100644 index 0000000000..71087771cb --- /dev/null +++ b/cpu/ppc4xx/xilinx_irq.c @@ -0,0 +1,100 @@ +/* + * (C) Copyright 2008 + * Ricado Ribalda-Universidad Autonoma de Madrid-ricardo.ribalda@uam.es + * This work has been supported by: QTechnology http://qtec.com/ + * Based on interrupts.c Wolfgang Denk-DENX Software Engineering-wd@denx.de + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include <common.h> +#include <watchdog.h> +#include <command.h> +#include <asm/processor.h> +#include <asm/interrupt.h> +#include <ppc4xx.h> +#include <ppc_asm.tmpl> +#include <commproc.h> +#include <asm/io.h> +#include <asm/xilinx_irq.h> + +DECLARE_GLOBAL_DATA_PTR; + +void pic_enable(void) +{ + debug("Xilinx PIC at 0x%8x\n", intc); + + /* + * Disable all external interrupts until they are + * explicitly requested. + */ + out_be32((u32 *) IER, 0); + + /* Acknowledge any pending interrupts just in case. */ + out_be32((u32 *) IAR, 0xffffffff); + + /* Turn on the Master Enable. */ + out_be32((u32 *) MER, 0x3UL); + + return; +} + +int xilinx_pic_irq_get(void) +{ + u32 irq; + irq = in_be32((u32 *) IVR); + + /* If no interrupt is pending then all bits of the IVR are set to 1. As + * the IVR is as many bits wide as numbers of inputs are available. + * Therefore, if all bits of the IVR are set to one, its content will + * be bigger than XPAR_INTC_MAX_NUM_INTR_INPUTS. + */ + if (irq >= XPAR_INTC_MAX_NUM_INTR_INPUTS) + irq = -1; /* report no pending interrupt. */ + + debug("get_irq: %d\n", irq); + return (irq); +} + +void pic_irq_enable(unsigned int irq) +{ + u32 mask = IRQ_MASK(irq); + debug("enable: %d\n", irq); + out_be32((u32 *) SIE, mask); +} + +void pic_irq_disable(unsigned int irq) +{ + u32 mask = IRQ_MASK(irq); + debug("disable: %d\n", irq); + out_be32((u32 *) CIE, mask); +} + +void pic_irq_ack(unsigned int irq) +{ + u32 mask = IRQ_MASK(irq); + debug("ack: %d\n", irq); + out_be32((u32 *) IAR, mask); +} + +void external_interrupt(struct pt_regs *regs) +{ + int irq; + + irq = xilinx_pic_irq_get(); + if (irq < 0) + return; + + interrupt_run_handler(irq); + + return; +} |