1 files changed, 115 insertions, 0 deletions
diff --git a/drivers/mmc/fsl_esdhc_spl.c b/drivers/mmc/fsl_esdhc_spl.c
new file mode 100644
index 0000000000..65c52a22db
--- /dev/null
+++ b/drivers/mmc/fsl_esdhc_spl.c
@@ -0,0 +1,115 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <mmc.h>
+#include <malloc.h>
+
+/*
+ * The environment variables are written to just after the u-boot image
+ * on SDCard, so we must read the MBR to get the start address and code
+ * length of the u-boot image, then calculate the address of the env.
+ */
+#define ESDHC_BOOT_IMAGE_SIZE	0x48
+#define ESDHC_BOOT_IMAGE_ADDR	0x50
+#define MBRDBR_BOOT_SIG_55	0x1fe
+#define MBRDBR_BOOT_SIG_AA	0x1ff
+#define CONFIG_CFG_DATA_SECTOR	0
+
+/*
+ * The main entry for mmc booting. It's necessary that SDRAM is already
+ * configured and available since this code loads the main U-Boot image
+ * from mmc into SDRAM and starts it from there.
+ */
+
+void __noreturn mmc_boot(void)
+{
+	__attribute__((noreturn)) void (*uboot)(void);
+	uint blk_start, blk_cnt, err;
+	u32 blklen;
+	uchar *tmp_buf;
+	uchar val;
+	uint i, byte_num;
+	u32 offset, code_len;
+	struct mmc *mmc;
+
+	mmc = find_mmc_device(0);
+	if (!mmc) {
+		puts("spl: mmc device not found!!\n");
+		hang();
+	}
+
+	blklen = mmc->read_bl_len;
+	tmp_buf = malloc(blklen);
+	if (!tmp_buf) {
+		puts("spl: malloc memory failed!!\n");
+		hang();
+	}
+	memset(tmp_buf, 0, blklen);
+
+	/*
+	* Read source addr from sd card
+	*/
+	err = mmc->block_dev.block_read(0, CONFIG_CFG_DATA_SECTOR, 1, tmp_buf);
+	if (err != 1) {
+		puts("spl: mmc read failed!!\n");
+		free(tmp_buf);
+		hang();
+	}
+
+	val = *(tmp_buf + MBRDBR_BOOT_SIG_55);
+	if (0x55 != val) {
+		puts("spl: mmc signature is not valid!!\n");
+		free(tmp_buf);
+		hang();
+	}
+	val = *(tmp_buf + MBRDBR_BOOT_SIG_AA);
+	if (0xAA != val) {
+		puts("spl: mmc signature is not valid!!\n");
+		free(tmp_buf);
+		hang();
+	}
+
+	byte_num = 4;
+	offset = 0;
+	for (i = 0; i < byte_num; i++) {
+		val = *(tmp_buf + ESDHC_BOOT_IMAGE_ADDR + i);
+		offset = (offset << 8) + val;
+	}
+	offset += CONFIG_SYS_MMC_U_BOOT_OFFS;
+	/* Get the code size from offset 0x48 */
+	byte_num = 4;
+	code_len = 0;
+	for (i = 0; i < byte_num; i++) {
+		val = *(tmp_buf + ESDHC_BOOT_IMAGE_SIZE + i);
+		code_len = (code_len << 8) + val;
+	}
+	code_len -= CONFIG_SYS_MMC_U_BOOT_OFFS;
+	/*
+	* Load U-Boot image from mmc into RAM
+	*/
+	blk_start = ALIGN(offset, mmc->read_bl_len) / mmc->read_bl_len;
+	blk_cnt = ALIGN(code_len, mmc->read_bl_len) / mmc->read_bl_len;
+	err = mmc->block_dev.block_read(0, blk_start, blk_cnt,
+					(uchar *)CONFIG_SYS_MMC_U_BOOT_DST);
+	if (err != blk_cnt) {
+		puts("spl: mmc read failed!!\n");
+		free(tmp_buf);
+		hang();
+	}
+
+	/*
+	* Clean d-cache and invalidate i-cache, to
+	* make sure that no stale data is executed.
+	*/
+	flush_cache(CONFIG_SYS_MMC_U_BOOT_DST, CONFIG_SYS_MMC_U_BOOT_SIZE);
+
+	/*
+	* Jump to U-Boot image
+	*/
+	uboot = (void *)CONFIG_SYS_MMC_U_BOOT_START;
+	(*uboot)();
+}