summaryrefslogtreecommitdiff
path: root/drivers/net/npe/include/IxI2cDrv.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/npe/include/IxI2cDrv.h')
-rw-r--r--drivers/net/npe/include/IxI2cDrv.h843
1 files changed, 0 insertions, 843 deletions
diff --git a/drivers/net/npe/include/IxI2cDrv.h b/drivers/net/npe/include/IxI2cDrv.h
deleted file mode 100644
index 033154046f..0000000000
--- a/drivers/net/npe/include/IxI2cDrv.h
+++ /dev/null
@@ -1,843 +0,0 @@
-/**
- * @file IxI2cDrv.h
- *
- * @brief Header file for the IXP400 I2C Driver (IxI2cDrv)
- *
- * @version $Revision: 0.1 $
- *
- * @par
- * IXP400 SW Release version 2.0
- *
- * -- Copyright Notice --
- *
- * @par
- * Copyright 2001-2005, Intel Corporation.
- * All rights reserved.
- *
- * @par
- * SPDX-License-Identifier: BSD-3-Clause
- * @par
- * -- End of Copyright Notice --
- */
-
-/**
- * @defgroup IxI2cDrv IXP400 I2C Driver(IxI2cDrv) API
- *
- * @brief IXP400 I2C Driver Public API
- *
- * @{
- */
-#ifndef IXI2CDRV_H
-#define IXI2CDRV_H
-
-#ifdef __ixp46X
-#include "IxOsal.h"
-
-/*
- * Section for #define
- */
-
-/**
- * @ingroup IxI2cDrv
- * @brief The interval of micro/mili seconds the IXP will wait before it polls for
- * status from the ixI2cIntrXferStatus; Every 20us is 1 byte @
- * 400Kbps and 4 bytes @ 100Kbps. This is dependent on delay type selected
- * through the API ixI2cDrvDelayTypeSelect.
- */
-#define IX_I2C_US_POLL_FOR_XFER_STATUS 20
-
-/**
- * @ingroup IxI2cDrv
- * @brief The number of tries that will be attempted to call a callback
- * function if the callback does not or is unable to resolve the
- * issue it is called to resolve
- */
-#define IX_I2C_NUM_OF_TRIES_TO_CALL_CALLBACK_FUNC 10
-
-
-/**
- * @ingroup IxI2cDrv
- * @brief Number of tries slave will poll the IDBR Rx full bit before it
- * gives up
- */
-#define IX_I2C_NUM_TO_POLL_IDBR_RX_FULL 0x100
-
-/**
- * @ingroup IxI2cDrv
- * @brief Number of tries slave will poll the IDBR Tx empty bit before it
- * gives up
- */
-#define IX_I2C_NUM_TO_POLL_IDBR_TX_EMPTY 0x100
-
-/*
- * Section for enum
- */
-
-/**
- * @ingroup IxI2cDrv
- *
- * @enum IxI2cMasterStatus
- *
- * @brief The master status - transfer complete, bus error or arbitration loss
- */
-typedef enum
-{
- IX_I2C_MASTER_XFER_COMPLETE = IX_SUCCESS,
- IX_I2C_MASTER_XFER_BUS_ERROR,
- IX_I2C_MASTER_XFER_ARB_LOSS
-} IxI2cMasterStatus;
-
-
-/**
- * @ingroup IxI2cDrv
- *
- * @enum IX_I2C_STATUS
- *
- * @brief The status that can be returned in a I2C driver initialization
- */
-typedef enum
-{
- IX_I2C_SUCCESS = IX_SUCCESS, /**< Success status */
- IX_I2C_FAIL, /**< Fail status */
- IX_I2C_NOT_SUPPORTED, /**< hardware does not have dedicated I2C hardware */
- IX_I2C_NULL_POINTER, /**< parameter passed in is NULL */
- IX_I2C_INVALID_SPEED_MODE_ENUM_VALUE, /**< speed mode selected is invalid */
- IX_I2C_INVALID_FLOW_MODE_ENUM_VALUE, /**< flow mode selected is invalid */
- IX_I2C_SLAVE_ADDR_CB_MISSING, /**< slave callback is NULL */
- IX_I2C_GEN_CALL_CB_MISSING, /**< general callback is NULL */
- IX_I2C_INVALID_SLAVE_ADDR, /**< invalid slave address specified */
- IX_I2C_INT_BIND_FAIL, /**< interrupt bind fail */
- IX_I2C_INT_UNBIND_FAIL, /**< interrupt unbind fail */
- IX_I2C_NOT_INIT, /**< I2C is not initialized yet */
- IX_I2C_MASTER_BUS_BUSY, /**< master detected a I2C bus busy */
- IX_I2C_MASTER_ARB_LOSS, /**< master experienced arbitration loss */
- IX_I2C_MASTER_XFER_ERROR, /**< master experienced a transfer error */
- IX_I2C_MASTER_BUS_ERROR, /**< master detected a I2C bus error */
- IX_I2C_MASTER_NO_BUFFER, /**< no buffer provided for master transfer */
- IX_I2C_MASTER_INVALID_XFER_MODE, /**< xfer mode selected is invalid */
- IX_I2C_SLAVE_ADDR_NOT_DETECTED, /**< polled slave addr not detected */
- IX_I2C_GEN_CALL_ADDR_DETECTED, /**< polling detected general call */
- IX_I2C_SLAVE_READ_DETECTED, /**< polling detected slave read request */
- IX_I2C_SLAVE_WRITE_DETECTED, /**< polling detected slave write request */
- IX_I2C_SLAVE_NO_BUFFER, /**< no buffer provided for slave transfers */
- IX_I2C_DATA_SIZE_ZERO, /**< data size transfer is zero - invalid */
- IX_I2C_SLAVE_WRITE_BUFFER_EMPTY, /**< slave buffer is used till empty */
- IX_I2C_SLAVE_WRITE_ERROR, /**< slave write experienced an error */
- IX_I2C_SLAVE_OR_GEN_READ_BUFFER_FULL, /**< slave buffer is filled up */
- IX_I2C_SLAVE_OR_GEN_READ_ERROR /**< slave read experienced an error */
-} IX_I2C_STATUS;
-
-/**
- * @ingroup IxI2cDrv
- *
- * @enum IxI2cSpeedMode
- *
- * @brief Type of speed modes supported by the I2C hardware.
- */
-typedef enum
-{
- IX_I2C_NORMAL_MODE = 0x0,
- IX_I2C_FAST_MODE
-} IxI2cSpeedMode;
-
-/**
- * @ingroup IxI2cDrv
- *
- * @enum IxI2cXferMode
- *
- * @brief Used for indicating it is a repeated start or normal transfer
- */
-typedef enum
-{
- IX_I2C_NORMAL = 0x0,
- IX_I2C_REPEATED_START
-} IxI2cXferMode;
-
-/**
- * @ingroup IxI2cDrv
- *
- * @enum IxI2cFlowMode
- *
- * @brief Used for indicating it is a poll or interrupt mode
- */
-typedef enum
-{
- IX_I2C_POLL_MODE = 0x0,
- IX_I2C_INTERRUPT_MODE
-} IxI2cFlowMode;
-
-/**
- * @ingroup IxI2cDrv
- *
- * @enum IxI2cDelayMode
- *
- * @brief Used for selecting looping delay or OS scheduler delay
- */
-typedef enum
-{
- IX_I2C_LOOP_DELAY = 1, /**< delay in microseconds */
- IX_I2C_SCHED_DELAY /**< delay in miliseconds */
-} IxI2cDelayMode;
-
-/**
- * @ingroup IxI2cDrv
- *
- * @brief The pointer to the function that will be called when the master
- * has completed its receive. The parameter that is passed will
- * provide the status of the read (success, arb loss, or bus
- * error), the transfer mode (normal or repeated start, the
- * buffer pointer and number of bytes transferred.
- */
-typedef void (*IxI2cMasterReadCallbackP)(IxI2cMasterStatus, IxI2cXferMode, char*, UINT32);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @brief The pointer to the function that will be called when the master
- * has completed its transmit. The parameter that is passed will
- * provide the status of the write (success, arb loss, or buss
- * error), the transfer mode (normal or repeated start), the
- * buffer pointer and number of bytes transferred.
- */
-typedef void (*IxI2cMasterWriteCallbackP)(IxI2cMasterStatus, IxI2cXferMode, char*, UINT32);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @brief The pointer to the function that will be called when a slave
- * address detected in interrupt mode for a read. The parameters
- * that is passed will provide the read status, buffer pointer,
- * buffer size, and the bytes received. When a start of a read
- * is initiated there will be no buffer allocated and this callback
- * will be called to request for a buffer. While receiving, if the
- * buffer gets filled, this callback will be called to request for
- * a new buffer while sending the filled buffer's pointer and size,
- * and data size received. When the receive is complete, this
- * callback will be called to process the data and free the memory
- * by passing the buffer's pointer and size, and data size received.
- */
-typedef void (*IxI2cSlaveReadCallbackP)(IX_I2C_STATUS, char*, UINT32, UINT32);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @brief The pointer to the function that will be called when a slave
- * address detected in interrupt mode for a write. The parameters
- * that is passed will provide the write status, buffer pointer,
- * buffer size, and the bytes received. When a start of a write is
- * initiated there will be no buffer allocated and this callback
- * will be called to request for a buffer and to fill it with data.
- * While transmitting, if the data in the buffer empties, this
- * callback will be called to request for more data to be filled in
- * the same or new buffer. When the transmit is complete, this
- * callback will be called to free the memory or other actions to
- * be taken.
- */
-typedef void (*IxI2cSlaveWriteCallbackP)(IX_I2C_STATUS, char*, UINT32, UINT32);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @brief The pointer to the function that will be called when a general
- * call detected in interrupt mode for a read. The parameters that
- * is passed will provide the read status, buffer pointer, buffer
- * size, and the bytes received. When a start of a read is
- * initiated there will be no buffer allocated and this callback
- * will be called to request for a buffer. While receiving, if the
- * buffer gets filled, this callback will be called to request for
- * a new buffer while sending the filled buffer's pointer and size,
- * and data size received. When the receive is complete, this
- * callback will be called to process the data and free the memory
- * by passing the buffer's pointer and size, and data size received.
- */
-typedef void (*IxI2cGenCallCallbackP)(IX_I2C_STATUS, char*, UINT32, UINT32);
-
-/*
- * Section for struct
- */
-
-/**
- * @brief contains all the variables required to initialize the I2C unit
- *
- * Structure to be filled and used for calling initialization
- */
-typedef struct
-{
- IxI2cSpeedMode I2cSpeedSelect; /**<Select either normal (100kbps)
- or fast mode (400kbps)*/
- IxI2cFlowMode I2cFlowSelect; /**<Select interrupt or poll mode*/
- IxI2cMasterReadCallbackP MasterReadCBP;
- /**<The master read callback pointer */
- IxI2cMasterWriteCallbackP MasterWriteCBP;
- /**<The master write callback pointer */
- IxI2cSlaveReadCallbackP SlaveReadCBP;
- /**<The slave read callback pointer */
- IxI2cSlaveWriteCallbackP SlaveWriteCBP;
- /**<The slave write callback pointer */
- IxI2cGenCallCallbackP GenCallCBP;
- /**<The general call callback pointer */
- BOOL I2cGenCallResponseEnable; /**<Enable/disable the unit to
- respond to generall calls.*/
- BOOL I2cSlaveAddrResponseEnable;/**<Enable/disable the unit to
- respond to the slave address set in
- ISAR*/
- BOOL SCLEnable; /**<Enable/disable the unit from
- driving the SCL line during master
- mode operation*/
- UINT8 I2cHWAddr; /**<The address the unit will
- response to as a slave device*/
-} IxI2cInitVars;
-
-/**
- * @brief contains results of counters and their overflow
- *
- * Structure contains all values of counters and associated overflows.
- */
-typedef struct
-{
- UINT32 ixI2cMasterXmitCounter; /**<Total bytes transmitted as
- master.*/
- UINT32 ixI2cMasterFailedXmitCounter; /**<Total bytes failed for
- transmission as master.*/
- UINT32 ixI2cMasterRcvCounter; /**<Total bytes received as
- master.*/
- UINT32 ixI2cMasterFailedRcvCounter; /**<Total bytes failed for
- receival as master.*/
- UINT32 ixI2cSlaveXmitCounter; /**<Total bytes transmitted as
- slave.*/
- UINT32 ixI2cSlaveFailedXmitCounter; /**<Total bytes failed for
- transmission as slave.*/
- UINT32 ixI2cSlaveRcvCounter; /**<Total bytes received as
- slave.*/
- UINT32 ixI2cSlaveFailedRcvCounter; /**<Total bytes failed for
- receival as slave.*/
- UINT32 ixI2cGenAddrCallSucceedCounter; /**<Total bytes successfully
- transmitted for general address.*/
- UINT32 ixI2cGenAddrCallFailedCounter; /**<Total bytes failed transmission
- for general address.*/
- UINT32 ixI2cArbLossCounter; /**<Total instances of arbitration
- loss has occured.*/
-} IxI2cStatsCounters;
-
-
-/*
- * Section for prototypes interface functions
- */
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvInit(
- IxI2cInitVars *InitVarsSelected)
- *
- * @brief Initializes the I2C Driver.
- *
- * @param "IxI2cInitVars [in] *InitVarsSelected" - struct containing required
- * variables for initialization
- *
- * Global Data :
- * - None.
- *
- * This API will check if the hardware supports this I2C driver and the validity
- * of the parameters passed in. It will continue to process the parameters
- * passed in by setting the speed of the I2C unit (100kbps or 400kbps), setting
- * the flow to either interrupt or poll mode, setting the address of the I2C unit,
- * enabling/disabling the respond to General Calls, enabling/disabling the respond
- * to Slave Address and SCL line driving. If it is interrupt mode, then it will
- * register the callback routines for master, slavetransfer and general call receive.
- *
- * @return
- * - IX_I2C_SUCCESS - Successfully initialize and enable the I2C
- * hardware.
- * - IX_I2C_NOT_SUPPORTED - The hardware does not support or have a
- * dedicated I2C unit to support this driver
- * - IX_I2C_NULL_POINTER - The parameter passed in is a NULL pointed
- * - IX_I2C_INVALID_SPEED_MODE_ENUM_VALUE - The speed mode selected in the
- * InitVarsSelected is invalid
- * - IX_I2C_INVALID_FLOW_MODE_ENUM_VALUE - The flow mode selected in the
- * InitVarsSelected is invalid
- * - IX_I2C_INVALID_SLAVE_ADDR - The address 0x0 is reserved for
- * general call.
- * - IX_I2C_SLAVE_ADDR_CB_MISSING - interrupt mode is selected but
- * slave address callback pointer is NULL
- * - IX_I2C_GEN_CALL_CB_MISSING - interrupt mode is selected but
- * general call callback pointer is NULL
- * - IX_I2C_INT_BIND_FAIL - The ISR for the I2C failed to bind
- * - IX_I2C_INT_UNBIND_FAIL - The ISR for the I2C failed to unbind
- *
- * @li Reentrant : yes
- * @li ISR Callable : yes
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvInit(IxI2cInitVars *InitVarsSelected);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvUninit(
- void)
- *
- * @brief Disables the I2C hardware
- *
- * @param - None
- *
- * Global Data :
- * - None.
- *
- * This API will disable the I2C hardware, unbind interrupt, and unmap memory.
- *
- * @return
- * - IX_I2C_SUCCESS - successfully un-initialized I2C
- * - IX_I2C_INT_UNBIND_FAIL - failed to unbind the I2C interrupt
- * - IX_I2C_NOT_INIT - I2C not init yet.
- *
- * @li Reentrant : yes
- * @li ISR Callable : yes
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvUninit(void);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvSlaveAddrSet(
- UINT8 SlaveAddrSet)
- *
- * @brief Sets the I2C Slave Address
- *
- * @param "UINT8 [in] SlaveAddrSet" - Slave Address to be inserted into ISAR
- *
- * Global Data :
- * - None.
- *
- * This API will insert the SlaveAddrSet into the ISAR.
- *
- * @return
- * - IX_I2C_SUCCESS - successfuly set the slave addr
- * - IX_I2C_INVALID_SLAVE_ADDR - invalid slave address (zero) specified
- * - IX_I2C_NOT_INIT - I2C not init yet.
- *
- * @li Reentrant : yes
- * @li ISR Callable : yes
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvSlaveAddrSet(UINT8 SlaveAddrSet);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvBusScan(
- void)
- *
- * @brief scans the I2C bus for slave devices
- *
- * @param - None
- *
- * Global Data :
- * - None.
- *
- * This API will prompt all slave addresses for a reply except its own
- *
- * @return
- * - IX_I2C_SUCCESS - found at least one slave device
- * - IX_I2C_FAIL - Fail to find even one slave device
- * - IX_I2C_BUS_BUSY - The I2C bus is busy (held by another I2C master)
- * - IX_I2C_ARB_LOSS - The I2C bus was loss to another I2C master
- * - IX_I2C_NOT_INIT - I2C not init yet.
- *
- * @li Reentrant : yes
- * @li ISR Callable : yes
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvBusScan(void);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvWriteTransfer(
- UINT8 SlaveAddr,
- char *bufP,
- UINT32 dataSize,
- IxI2cXferMode XferModeSelect)
- *
- * @param "UINT8 [in] SlaveAddr" - The slave address to request data from.
- * @param "char [in] *bufP" - The pointer to the data to be transmitted.
- * @param "UINT32 [in] dataSize" - The number of bytes requested.
- * @param "IxI2cXferMode [in] XferModeSelect" - the transfer mode selected,
- * either repeated start (ends w/o stop) or normal (start and stop)
- *
- * Global Data :
- * - None.
- *
- * This API will try to obtain master control of the I2C bus and transmit the
- * number of bytes, specified by dataSize, to the user specified slave
- * address from the buffer pointer. It will use either interrupt or poll mode
- * depending on the method selected.
- *
- * If in interrupt mode and IxI2cMasterWriteCallbackP is not NULL, the driver
- * will initiate the transfer and return immediately. The function pointed to
- * by IxI2cMasterWriteCallbackP will be called in the interrupt service
- * handlers when the operation is complete.
- *
- * If in interrupt mode and IxI2cMasterWriteCallbackP is NULL, then the driver
- * will wait for the operation to complete, and then return.
- *
- * And if the repeated start transfer mode is selected, then it will not send a
- * stop signal at the end of all the transfers.
- * *NOTE*: If repeated start transfer mode is selected, it has to end with a
- * normal mode transfer mode else the bus will continue to be held
- * by the IXP.
- *
- * @return
- * - IX_I2C_SUCCESS - Successfuuly wrote data to slave.
- * - IX_I2C_MASTER_BUS_BUSY - The I2C bus is busy (held by another I2C master)
- * - IX_I2C_MASTER_ARB_LOSS - The I2C bus was loss to another I2C master
- * - IX_I2C_MASTER_XFER_ERROR - There was a transfer error
- * - IX_I2C_MASTER_BUS_ERROR - There was a bus error during transfer
- * - IX_I2C_MASTER_NO_BUFFER - buffer pointer is NULL
- * - IX_I2C_MASTER_INVALID_XFER_MODE - Xfer mode selected is invalid
- * - IX_I2C_DATA_SIZE_ZERO - dataSize passed in is zero, which is invalid
- * - IX_I2C_NOT_INIT - I2C not init yet.
- *
- * @li Reentrant : no
- * @li ISR Callable : no
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvWriteTransfer(
- UINT8 SlaveAddr,
- char *bufP,
- UINT32 dataSize,
- IxI2cXferMode XferModeSelect);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvReadTransfer(
- UINT8 SlaveAddr,
- char *bufP,
- UINT32 dataSize,
- IxI2cXferMode XferModeSelect)
- *
- * @brief Initiates a transfer to receive bytes of data from a slave
- * device through the I2C bus.
- *
- * @param "UINT8 [in] SlaveAddr" - The slave address to request data from.
- * @param "char [out] *bufP" - The pointer to the buffer to store the
- * requested data.
- * @param "UINT32 [in] dataSize" - The number of bytes requested.
- * @param "IxI2cXferMode [in] XferModeSelect" - the transfer mode selected,
- * either repeated start (ends w/o stop) or normal (start and stop)
- *
- * Global Data :
- * - None.
- *
- * This API will try to obtain master control of the I2C bus and receive the
- * number of bytes, specified by dataSize, from the user specified address
- * into the receive buffer. It will use either interrupt or poll mode depending
- * on the mode selected.
- *
- * If in interrupt mode and IxI2cMasterReadCallbackP is not NULL, the driver
- * will initiate the transfer and return immediately. The function pointed to
- * by IxI2cMasterReadCallbackP will be called in the interrupt service
- * handlers when the operation is complete.
- *
- * If in interrupt mode and IxI2cMasterReadCallbackP is NULL, then the driver will
- * wait for the operation to complete, and then return.
- *
- * And if the repeated start transfer mode is selected, then it will not send a
- * stop signal at the end of all the transfers.
- * *NOTE*: If repeated start transfer mode is selected, it has to end with a
- * normal mode transfer mode else the bus will continue to be held
- * by the IXP.
- *
- * @return
- * - IX_I2C_SUCCESS - Successfuuly read slave data
- * - IX_I2C_MASTER_BUS_BUSY - The I2C bus is busy (held by another I2C master)
- * - IX_I2C_MASTER_ARB_LOSS - The I2C bus was loss to another I2C master
- * - IX_I2C_MASTER_XFER_ERROR - There was a bus error during transfer
- * - IX_I2C_MASTER_BUS_ERROR - There was a bus error during transfer
- * - IX_I2C_MASTER_NO_BUFFER - buffer pointer is NULL
- * - IX_I2C_MASTER_INVALID_XFER_MODE - Xfer mode selected is invalid
- * - IX_I2C_INVALID_SLAVE_ADDR - invalid slave address (zero) specified
- * - IX_I2C_DATA_SIZE_ZERO - dataSize passed in is zero, which is invalid
- * - IX_I2C_NOT_INIT - I2C not init yet.
- *
- * @li Reentrant : no
- * @li ISR Callable : no
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvReadTransfer(
- UINT8 SlaveAddr,
- char *bufP,
- UINT32 dataSize,
- IxI2cXferMode XferModeSelect);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvSlaveAddrAndGenCallDetectedCheck(
- void)
- *
- * @brief Checks the I2C Status Register to determine if a slave address is
- * detected
- *
- * @param - None
- *
- * Global Data :
- * - None.
- *
- * This API is used in polled mode to determine if the I2C unit is requested
- * for a slave or general call transfer. If it is requested for a slave
- * transfer then it will determine if it is a general call (read only), read,
- * or write transfer requested.
- *
- * @return
- * - IX_I2C_SLAVE_ADDR_NOT_DETECTED - The I2C unit is not requested for slave
- * transfer
- * - IX_I2C_GEN_CALL_ADDR_DETECTED - The I2C unit is not requested for slave
- * transfer but for general call
- * - IX_I2C_SLAVE_READ_DETECTED - The I2C unit is requested for a read
- * - IX_I2C_SLAVE_WRITE_DETECTED - The I2C unit is requested for a write
- * - IX_I2C_NOT_INIT - I2C not init yet.
- *
- * @li Reentrant : no
- * @li ISR Callable : no
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvSlaveAddrAndGenCallDetectedCheck(void);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvSlaveOrGenDataReceive(
- char *bufP,
- UINT32 bufSize,
- UINT32 *dataSizeRcvd)
- *
- * @brief Performs the slave receive or general call receive data transfer
- *
- * @param "char [in] *bufP" - the pointer to the buffer to store data
- * "UINT32 [in] bufSize" - the buffer size allocated
- * "UINT32 [in] *dataSizeRcvd" - the length of data received in bytes
- *
- * Global Data :
- * - None.
- *
- * This API is only used in polled mode to perform the slave read or general call
- * receive data. It will continuously store the data received into bufP until
- * complete or until bufP is full in which it will return
- * IX_I2C_SLAVE_OR_GEN_READ_BUFFER_FULL. If in interrupt mode, the callback will be
- * used.
- *
- * @return
- * - IX_I2C_SUCCESS - The I2C driver transferred the data successfully.
- * - IX_I2C_SLAVE_OR_GEN_READ_BUFFER_FULL - The I2C driver has ran out of
- * space to store the received data.
- * - IX_I2C_SLAVE_OR_GEN_READ_ERROR - The I2C driver didn't manage to
- * detect the IDBR Rx Full bit
- * - IX_I2C_DATA_SIZE_ZERO - bufSize passed in is zero, which is invalid
- * - IX_I2C_SLAVE_NO_BUFFER - buffer pointer is NULL
- * - IX_I2C_NULL_POINTER - dataSizeRcvd is NULL
- * - IX_I2C_NOT_INIT - I2C not init yet.
- *
- * @li Reentrant : no
- * @li ISR Callable : no
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvSlaveOrGenDataReceive(
- char *bufP,
- UINT32 bufSize,
- UINT32 *dataSizeRcvd);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvSlaveDataTransmit(
- char *bufP,
- UINT32 dataSize,
- UINT32 *dataSizeXmtd)
- *
- * @brief Performs the slave write data transfer
- *
- * @param "char [in] *bufP" - the pointer to the buffer for data to be
- * transmitted
- * "UINT32 [in] bufSize" - the buffer size allocated
- * "UINT32 [in] *dataSizeRcvd" - the length of data trasnmitted in
- * bytes
- *
- * Global Data :
- * - None.
- *
- * This API is only used in polled mode to perform the slave transmit data. It
- * will continuously transmit the data from bufP until complete or until bufP
- * is empty in which it will return IX_I2C_SLAVE_WRITE_BUFFER_EMPTY. If in
- * interrupt mode, the callback will be used.
- *
- * @return
- * - IX_I2C_SUCCESS - The I2C driver transferred the data successfully.
- * - IX_I2C_SLAVE_WRITE_BUFFER_EMPTY - The I2C driver needs more data to
- * transmit.
- * - IX_I2C_SLAVE_WRITE_ERROR -The I2C driver didn't manage to detect the
- * IDBR Tx empty bit or the slave stop bit.
- * - IX_I2C_DATA_SIZE_ZERO - dataSize passed in is zero, which is invalid
- * - IX_I2C_SLAVE_NO_BUFFER - buffer pointer is NULL
- * - IX_I2C_NULL_POINTER - dataSizeXmtd is NULL
- * - IX_I2C_NOT_INIT - I2C not init yet.
- *
- * @li Reentrant : no
- * @li ISR Callable : no
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvSlaveDataTransmit(
- char *bufP,
- UINT32 dataSize,
- UINT32 *dataSizeXmtd);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvSlaveOrGenCallBufReplenish(
- char *bufP,
- UINT32 bufSize)
- *
- * @brief Replenishes the buffer which stores buffer info for both slave and
- * general call
- *
- * @param "char [in] *bufP" - pointer to the buffer allocated
- * "UINT32 [in] bufSize" - size of the buffer
- *
- * Global Data :
- * - None.
- *
- * This API is only used in interrupt mode for replenishing the same buffer
- * that is used by both slave and generall call by updating the buffer info
- * with new info and clearing previous offsets set by previous transfers.
- *
- * @return
- * - None
- *
- * @li Reentrant : no
- * @li ISR Callable : no
- *
- */
-PUBLIC void
-ixI2cDrvSlaveOrGenCallBufReplenish(
- char *bufP,
- UINT32 bufSize);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvStatsGet(IxI2cStatsCounters *I2cStats)
- *
- * @brief Returns the I2C Statistics through the pointer passed in
- *
- * @param - "IxI2cStatsCounters [out] *I2cStats" - I2C statistics counter will
- * be read and written to the location pointed by this pointer.
- *
- * Global Data :
- * - None.
- *
- * This API will return the statistics counters of the I2C driver.
- *
- * @return
- * - IX_I2C_NULL_POINTER - pointer passed in is NULL
- * - IX_I2C_SUCCESS - successfully obtained I2C statistics
- *
- * @li Reentrant : yes
- * @li ISR Callable : no
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvStatsGet(IxI2cStatsCounters *I2cStats);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvStatsReset(void)
- *
- * @brief Reset I2C statistics counters.
- *
- * @param - None
- *
- * Global Data :
- * - None.
- *
- * This API will reset the statistics counters of the I2C driver.
- *
- * @return
- * - None
- *
- * @li Reentrant : yes
- * @li ISR Callable : no
- *
- */
-PUBLIC void
-ixI2cDrvStatsReset(void);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvShow(void)
- *
- * @brief Displays the I2C status register and the statistics counter.
- *
- * @param - None
- *
- * Global Data :
- * - None.
- *
- * This API will display the I2C Status register and is useful if any error
- * occurs. It displays the detection of bus error, slave address, general call,
- * address, IDBR receive full, IDBR transmit empty, arbitration loss, slave
- * STOP signal, I2C bus busy, unit busy, ack/nack, and read/write mode. It will
- * also call the ixI2cDrvGetStats and then display the statistics counter.
- *
- * @return
- * - IX_I2C_SUCCESS - successfully displayed statistics and status register
- * - IX_I2C_NOT_INIT - I2C not init yet.
- *
- * @li Reentrant : yes
- * @li ISR Callable : no
- *
- */
-PUBLIC IX_I2C_STATUS
-ixI2cDrvShow(void);
-
-/**
- * @ingroup IxI2cDrv
- *
- * @fn ixI2cDrvDelayTypeSelect (IxI2cDelayMode delayMechanismSelect)
- *
- * @brief Sets the delay type of either looping delay or OS scheduler delay
- * according to the argument provided.
- *
- * @param - "IxI2cDelayMode [in] delayTypeSelect" - the I2C delay type selected
- *
- * Global Data :
- * - None.
- *
- * This API will set the delay type used by the I2C Driver to either looping
- * delay or OS scheduler delay.
- *
- * @return
- * - None
- *
- * @li Reentrant : yes
- * @li ISR Callable : no
- *
- */
-PUBLIC void
-ixI2cDrvDelayTypeSelect (IxI2cDelayMode delayTypeSelect);
-
-#endif /* __ixp46X */
-#endif /* IXI2CDRV_H */