diff options
Diffstat (limited to 'drivers/spi/cadence_qspi_apb.c')
| -rw-r--r-- | drivers/spi/cadence_qspi_apb.c | 185 |
1 files changed, 84 insertions, 101 deletions
diff --git a/drivers/spi/cadence_qspi_apb.c b/drivers/spi/cadence_qspi_apb.c index e285d3c1e7..df6a91fc9f 100644 --- a/drivers/spi/cadence_qspi_apb.c +++ b/drivers/spi/cadence_qspi_apb.c @@ -32,37 +32,37 @@ #include <spi.h> #include "cadence_qspi.h" -#define CQSPI_REG_POLL_US (1) /* 1us */ -#define CQSPI_REG_RETRY (10000) -#define CQSPI_POLL_IDLE_RETRY (3) +#define CQSPI_REG_POLL_US 1 /* 1us */ +#define CQSPI_REG_RETRY 10000 +#define CQSPI_POLL_IDLE_RETRY 3 -#define CQSPI_FIFO_WIDTH (4) +#define CQSPI_FIFO_WIDTH 4 -#define CQSPI_REG_SRAM_THRESHOLD_WORDS (50) +#define CQSPI_REG_SRAM_THRESHOLD_WORDS 50 /* Transfer mode */ -#define CQSPI_INST_TYPE_SINGLE (0) -#define CQSPI_INST_TYPE_DUAL (1) -#define CQSPI_INST_TYPE_QUAD (2) +#define CQSPI_INST_TYPE_SINGLE 0 +#define CQSPI_INST_TYPE_DUAL 1 +#define CQSPI_INST_TYPE_QUAD 2 -#define CQSPI_STIG_DATA_LEN_MAX (8) - -#define CQSPI_DUMMY_CLKS_PER_BYTE (8) -#define CQSPI_DUMMY_BYTES_MAX (4) +#define CQSPI_STIG_DATA_LEN_MAX 8 +#define CQSPI_DUMMY_CLKS_PER_BYTE 8 +#define CQSPI_DUMMY_BYTES_MAX 4 #define CQSPI_REG_SRAM_FILL_THRESHOLD \ ((CQSPI_REG_SRAM_SIZE_WORD / 2) * CQSPI_FIFO_WIDTH) + /**************************************************************************** * Controller's configuration and status register (offset from QSPI_BASE) ****************************************************************************/ #define CQSPI_REG_CONFIG 0x00 -#define CQSPI_REG_CONFIG_CLK_POL_LSB 1 -#define CQSPI_REG_CONFIG_CLK_PHA_LSB 2 -#define CQSPI_REG_CONFIG_ENABLE_MASK BIT(0) -#define CQSPI_REG_CONFIG_DIRECT_MASK BIT(7) -#define CQSPI_REG_CONFIG_DECODE_MASK BIT(9) -#define CQSPI_REG_CONFIG_XIP_IMM_MASK BIT(18) +#define CQSPI_REG_CONFIG_ENABLE BIT(0) +#define CQSPI_REG_CONFIG_CLK_POL BIT(1) +#define CQSPI_REG_CONFIG_CLK_PHA BIT(2) +#define CQSPI_REG_CONFIG_DIRECT BIT(7) +#define CQSPI_REG_CONFIG_DECODE BIT(9) +#define CQSPI_REG_CONFIG_XIP_IMM BIT(18) #define CQSPI_REG_CONFIG_CHIPSELECT_LSB 10 #define CQSPI_REG_CONFIG_BAUD_LSB 19 #define CQSPI_REG_CONFIG_IDLE_LSB 31 @@ -94,10 +94,10 @@ #define CQSPI_REG_DELAY_TSD2D_MASK 0xFF #define CQSPI_REG_DELAY_TSHSL_MASK 0xFF -#define CQSPI_READLCAPTURE 0x10 -#define CQSPI_READLCAPTURE_BYPASS_LSB 0 -#define CQSPI_READLCAPTURE_DELAY_LSB 1 -#define CQSPI_READLCAPTURE_DELAY_MASK 0xF +#define CQSPI_REG_RD_DATA_CAPTURE 0x10 +#define CQSPI_REG_RD_DATA_CAPTURE_BYPASS BIT(0) +#define CQSPI_REG_RD_DATA_CAPTURE_DELAY_LSB 1 +#define CQSPI_REG_RD_DATA_CAPTURE_DELAY_MASK 0xF #define CQSPI_REG_SIZE 0x14 #define CQSPI_REG_SIZE_ADDRESS_LSB 0 @@ -123,18 +123,18 @@ #define CQSPI_REG_IRQMASK 0x44 #define CQSPI_REG_INDIRECTRD 0x60 -#define CQSPI_REG_INDIRECTRD_START_MASK BIT(0) -#define CQSPI_REG_INDIRECTRD_CANCEL_MASK BIT(1) -#define CQSPI_REG_INDIRECTRD_INPROGRESS_MASK BIT(2) -#define CQSPI_REG_INDIRECTRD_DONE_MASK BIT(5) +#define CQSPI_REG_INDIRECTRD_START BIT(0) +#define CQSPI_REG_INDIRECTRD_CANCEL BIT(1) +#define CQSPI_REG_INDIRECTRD_INPROGRESS BIT(2) +#define CQSPI_REG_INDIRECTRD_DONE BIT(5) #define CQSPI_REG_INDIRECTRDWATERMARK 0x64 #define CQSPI_REG_INDIRECTRDSTARTADDR 0x68 #define CQSPI_REG_INDIRECTRDBYTES 0x6C #define CQSPI_REG_CMDCTRL 0x90 -#define CQSPI_REG_CMDCTRL_EXECUTE_MASK BIT(0) -#define CQSPI_REG_CMDCTRL_INPROGRESS_MASK BIT(1) +#define CQSPI_REG_CMDCTRL_EXECUTE BIT(0) +#define CQSPI_REG_CMDCTRL_INPROGRESS BIT(1) #define CQSPI_REG_CMDCTRL_DUMMY_LSB 7 #define CQSPI_REG_CMDCTRL_WR_BYTES_LSB 12 #define CQSPI_REG_CMDCTRL_WR_EN_LSB 15 @@ -150,10 +150,10 @@ #define CQSPI_REG_CMDCTRL_OPCODE_MASK 0xFF #define CQSPI_REG_INDIRECTWR 0x70 -#define CQSPI_REG_INDIRECTWR_START_MASK BIT(0) -#define CQSPI_REG_INDIRECTWR_CANCEL_MASK BIT(1) -#define CQSPI_REG_INDIRECTWR_INPROGRESS_MASK BIT(2) -#define CQSPI_REG_INDIRECTWR_DONE_MASK BIT(5) +#define CQSPI_REG_INDIRECTWR_START BIT(0) +#define CQSPI_REG_INDIRECTWR_CANCEL BIT(1) +#define CQSPI_REG_INDIRECTWR_INPROGRESS BIT(2) +#define CQSPI_REG_INDIRECTWR_DONE BIT(5) #define CQSPI_REG_INDIRECTWRWATERMARK 0x74 #define CQSPI_REG_INDIRECTWRSTARTADDR 0x78 @@ -169,9 +169,6 @@ ((readl(base + CQSPI_REG_CONFIG) >> \ CQSPI_REG_CONFIG_IDLE_LSB) & 0x1) -#define CQSPI_CAL_DELAY(tdelay_ns, tref_ns, tsclk_ns) \ - ((((tdelay_ns) - (tsclk_ns)) / (tref_ns))) - #define CQSPI_GET_RD_SRAM_LEVEL(reg_base) \ (((readl(reg_base + CQSPI_REG_SDRAMLEVEL)) >> \ CQSPI_REG_SDRAMLEVEL_RD_LSB) & CQSPI_REG_SDRAMLEVEL_RD_MASK) @@ -197,18 +194,16 @@ void cadence_qspi_apb_controller_enable(void *reg_base) { unsigned int reg; reg = readl(reg_base + CQSPI_REG_CONFIG); - reg |= CQSPI_REG_CONFIG_ENABLE_MASK; + reg |= CQSPI_REG_CONFIG_ENABLE; writel(reg, reg_base + CQSPI_REG_CONFIG); - return; } void cadence_qspi_apb_controller_disable(void *reg_base) { unsigned int reg; reg = readl(reg_base + CQSPI_REG_CONFIG); - reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK; + reg &= ~CQSPI_REG_CONFIG_ENABLE; writel(reg, reg_base + CQSPI_REG_CONFIG); - return; } /* Return 1 if idle, otherwise return 0 (busy). */ @@ -244,23 +239,22 @@ void cadence_qspi_apb_readdata_capture(void *reg_base, unsigned int reg; cadence_qspi_apb_controller_disable(reg_base); - reg = readl(reg_base + CQSPI_READLCAPTURE); + reg = readl(reg_base + CQSPI_REG_RD_DATA_CAPTURE); if (bypass) - reg |= (1 << CQSPI_READLCAPTURE_BYPASS_LSB); + reg |= CQSPI_REG_RD_DATA_CAPTURE_BYPASS; else - reg &= ~(1 << CQSPI_READLCAPTURE_BYPASS_LSB); + reg &= ~CQSPI_REG_RD_DATA_CAPTURE_BYPASS; - reg &= ~(CQSPI_READLCAPTURE_DELAY_MASK - << CQSPI_READLCAPTURE_DELAY_LSB); + reg &= ~(CQSPI_REG_RD_DATA_CAPTURE_DELAY_MASK + << CQSPI_REG_RD_DATA_CAPTURE_DELAY_LSB); - reg |= ((delay & CQSPI_READLCAPTURE_DELAY_MASK) - << CQSPI_READLCAPTURE_DELAY_LSB); + reg |= (delay & CQSPI_REG_RD_DATA_CAPTURE_DELAY_MASK) + << CQSPI_REG_RD_DATA_CAPTURE_DELAY_LSB; - writel(reg, reg_base + CQSPI_READLCAPTURE); + writel(reg, reg_base + CQSPI_REG_RD_DATA_CAPTURE); cadence_qspi_apb_controller_enable(reg_base); - return; } void cadence_qspi_apb_config_baudrate_div(void *reg_base, @@ -273,54 +267,42 @@ void cadence_qspi_apb_config_baudrate_div(void *reg_base, reg = readl(reg_base + CQSPI_REG_CONFIG); reg &= ~(CQSPI_REG_CONFIG_BAUD_MASK << CQSPI_REG_CONFIG_BAUD_LSB); - div = ref_clk_hz / sclk_hz; - - if (div > 32) - div = 32; - - /* Check if even number. */ - if ((div & 1)) { - div = (div / 2); - } else { - if (ref_clk_hz % sclk_hz) - /* ensure generated SCLK doesn't exceed user - specified sclk_hz */ - div = (div / 2); - else - div = (div / 2) - 1; - } - - debug("%s: ref_clk %dHz sclk %dHz Div 0x%x\n", __func__, - ref_clk_hz, sclk_hz, div); + /* + * The baud_div field in the config reg is 4 bits, and the ref clock is + * divided by 2 * (baud_div + 1). Round up the divider to ensure the + * SPI clock rate is less than or equal to the requested clock rate. + */ + div = DIV_ROUND_UP(ref_clk_hz, sclk_hz * 2) - 1; /* ensure the baud rate doesn't exceed the max value */ if (div > CQSPI_REG_CONFIG_BAUD_MASK) div = CQSPI_REG_CONFIG_BAUD_MASK; + debug("%s: ref_clk %dHz sclk %dHz Div 0x%x, actual %dHz\n", __func__, + ref_clk_hz, sclk_hz, div, ref_clk_hz / (2 * (div + 1))); + reg |= (div << CQSPI_REG_CONFIG_BAUD_LSB); writel(reg, reg_base + CQSPI_REG_CONFIG); cadence_qspi_apb_controller_enable(reg_base); - return; } -void cadence_qspi_apb_set_clk_mode(void *reg_base, - unsigned int clk_pol, unsigned int clk_pha) +void cadence_qspi_apb_set_clk_mode(void *reg_base, uint mode) { unsigned int reg; cadence_qspi_apb_controller_disable(reg_base); reg = readl(reg_base + CQSPI_REG_CONFIG); - reg &= ~(1 << - (CQSPI_REG_CONFIG_CLK_POL_LSB | CQSPI_REG_CONFIG_CLK_PHA_LSB)); + reg &= ~(CQSPI_REG_CONFIG_CLK_POL | CQSPI_REG_CONFIG_CLK_PHA); - reg |= ((clk_pol & 0x1) << CQSPI_REG_CONFIG_CLK_POL_LSB); - reg |= ((clk_pha & 0x1) << CQSPI_REG_CONFIG_CLK_PHA_LSB); + if (mode & SPI_CPOL) + reg |= CQSPI_REG_CONFIG_CLK_POL; + if (mode & SPI_CPHA) + reg |= CQSPI_REG_CONFIG_CLK_PHA; writel(reg, reg_base + CQSPI_REG_CONFIG); cadence_qspi_apb_controller_enable(reg_base); - return; } void cadence_qspi_apb_chipselect(void *reg_base, @@ -336,9 +318,9 @@ void cadence_qspi_apb_chipselect(void *reg_base, reg = readl(reg_base + CQSPI_REG_CONFIG); /* docoder */ if (decoder_enable) { - reg |= CQSPI_REG_CONFIG_DECODE_MASK; + reg |= CQSPI_REG_CONFIG_DECODE; } else { - reg &= ~CQSPI_REG_CONFIG_DECODE_MASK; + reg &= ~CQSPI_REG_CONFIG_DECODE; /* Convert CS if without decoder. * CS0 to 4b'1110 * CS1 to 4b'1101 @@ -355,7 +337,6 @@ void cadence_qspi_apb_chipselect(void *reg_base, writel(reg, reg_base + CQSPI_REG_CONFIG); cadence_qspi_apb_controller_enable(reg_base); - return; } void cadence_qspi_apb_delay(void *reg_base, @@ -371,16 +352,20 @@ void cadence_qspi_apb_delay(void *reg_base, cadence_qspi_apb_controller_disable(reg_base); /* Convert to ns. */ - ref_clk_ns = (1000000000) / ref_clk; + ref_clk_ns = DIV_ROUND_UP(1000000000, ref_clk); /* Convert to ns. */ - sclk_ns = (1000000000) / sclk_hz; - - /* Plus 1 to round up 1 clock cycle. */ - tshsl = CQSPI_CAL_DELAY(tshsl_ns, ref_clk_ns, sclk_ns) + 1; - tchsh = CQSPI_CAL_DELAY(tchsh_ns, ref_clk_ns, sclk_ns) + 1; - tslch = CQSPI_CAL_DELAY(tslch_ns, ref_clk_ns, sclk_ns) + 1; - tsd2d = CQSPI_CAL_DELAY(tsd2d_ns, ref_clk_ns, sclk_ns) + 1; + sclk_ns = DIV_ROUND_UP(1000000000, sclk_hz); + + /* The controller adds additional delay to that programmed in the reg */ + if (tshsl_ns >= sclk_ns + ref_clk_ns) + tshsl_ns -= sclk_ns + ref_clk_ns; + if (tchsh_ns >= sclk_ns + 3 * ref_clk_ns) + tchsh_ns -= sclk_ns + 3 * ref_clk_ns; + tshsl = DIV_ROUND_UP(tshsl_ns, ref_clk_ns); + tchsh = DIV_ROUND_UP(tchsh_ns, ref_clk_ns); + tslch = DIV_ROUND_UP(tslch_ns, ref_clk_ns); + tsd2d = DIV_ROUND_UP(tsd2d_ns, ref_clk_ns); reg = ((tshsl & CQSPI_REG_DELAY_TSHSL_MASK) << CQSPI_REG_DELAY_TSHSL_LSB); @@ -393,7 +378,6 @@ void cadence_qspi_apb_delay(void *reg_base, writel(reg, reg_base + CQSPI_REG_DELAY); cadence_qspi_apb_controller_enable(reg_base); - return; } void cadence_qspi_apb_controller_init(struct cadence_spi_platdata *plat) @@ -421,7 +405,6 @@ void cadence_qspi_apb_controller_init(struct cadence_spi_platdata *plat) writel(0, plat->regbase + CQSPI_REG_IRQMASK); cadence_qspi_apb_controller_enable(plat->regbase); - return; } static int cadence_qspi_apb_exec_flash_cmd(void *reg_base, @@ -432,12 +415,12 @@ static int cadence_qspi_apb_exec_flash_cmd(void *reg_base, /* Write the CMDCTRL without start execution. */ writel(reg, reg_base + CQSPI_REG_CMDCTRL); /* Start execute */ - reg |= CQSPI_REG_CMDCTRL_EXECUTE_MASK; + reg |= CQSPI_REG_CMDCTRL_EXECUTE; writel(reg, reg_base + CQSPI_REG_CMDCTRL); while (retry--) { reg = readl(reg_base + CQSPI_REG_CMDCTRL); - if ((reg & CQSPI_REG_CMDCTRL_INPROGRESS_MASK) == 0) + if ((reg & CQSPI_REG_CMDCTRL_INPROGRESS) == 0) break; udelay(1); } @@ -655,7 +638,7 @@ int cadence_qspi_apb_indirect_read_execute(struct cadence_spi_platdata *plat, writel(n_rx, plat->regbase + CQSPI_REG_INDIRECTRDBYTES); /* Start the indirect read transfer */ - writel(CQSPI_REG_INDIRECTRD_START_MASK, + writel(CQSPI_REG_INDIRECTRD_START, plat->regbase + CQSPI_REG_INDIRECTRD); while (remaining > 0) { @@ -684,21 +667,21 @@ int cadence_qspi_apb_indirect_read_execute(struct cadence_spi_platdata *plat, /* Check indirect done status */ ret = wait_for_bit("QSPI", plat->regbase + CQSPI_REG_INDIRECTRD, - CQSPI_REG_INDIRECTRD_DONE_MASK, 1, 10, 0); + CQSPI_REG_INDIRECTRD_DONE, 1, 10, 0); if (ret) { printf("Indirect read completion error (%i)\n", ret); goto failrd; } /* Clear indirect completion status */ - writel(CQSPI_REG_INDIRECTRD_DONE_MASK, + writel(CQSPI_REG_INDIRECTRD_DONE, plat->regbase + CQSPI_REG_INDIRECTRD); return 0; failrd: /* Cancel the indirect read */ - writel(CQSPI_REG_INDIRECTRD_CANCEL_MASK, + writel(CQSPI_REG_INDIRECTRD_CANCEL, plat->regbase + CQSPI_REG_INDIRECTRD); return ret; } @@ -746,7 +729,7 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat, writel(n_tx, plat->regbase + CQSPI_REG_INDIRECTWRBYTES); /* Start the indirect write transfer */ - writel(CQSPI_REG_INDIRECTWR_START_MASK, + writel(CQSPI_REG_INDIRECTWR_START, plat->regbase + CQSPI_REG_INDIRECTWR); while (remaining > 0) { @@ -771,20 +754,20 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat, /* Check indirect done status */ ret = wait_for_bit("QSPI", plat->regbase + CQSPI_REG_INDIRECTWR, - CQSPI_REG_INDIRECTWR_DONE_MASK, 1, 10, 0); + CQSPI_REG_INDIRECTWR_DONE, 1, 10, 0); if (ret) { printf("Indirect write completion error (%i)\n", ret); goto failwr; } /* Clear indirect completion status */ - writel(CQSPI_REG_INDIRECTWR_DONE_MASK, + writel(CQSPI_REG_INDIRECTWR_DONE, plat->regbase + CQSPI_REG_INDIRECTWR); return 0; failwr: /* Cancel the indirect write */ - writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK, + writel(CQSPI_REG_INDIRECTWR_CANCEL, plat->regbase + CQSPI_REG_INDIRECTWR); return ret; } @@ -795,9 +778,9 @@ void cadence_qspi_apb_enter_xip(void *reg_base, char xip_dummy) /* enter XiP mode immediately and enable direct mode */ reg = readl(reg_base + CQSPI_REG_CONFIG); - reg |= CQSPI_REG_CONFIG_ENABLE_MASK; - reg |= CQSPI_REG_CONFIG_DIRECT_MASK; - reg |= CQSPI_REG_CONFIG_XIP_IMM_MASK; + reg |= CQSPI_REG_CONFIG_ENABLE; + reg |= CQSPI_REG_CONFIG_DIRECT; + reg |= CQSPI_REG_CONFIG_XIP_IMM; writel(reg, reg_base + CQSPI_REG_CONFIG); /* keep the XiP mode */ |