diff options
Diffstat (limited to 'drivers/usb/host/ehci-omap.c')
| -rw-r--r-- | drivers/usb/host/ehci-omap.c | 60 |
1 files changed, 46 insertions, 14 deletions
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c index a47e078f62..3c58f9e656 100644 --- a/drivers/usb/host/ehci-omap.c +++ b/drivers/usb/host/ehci-omap.c @@ -28,18 +28,21 @@ static struct omap_ehci *const ehci = (struct omap_ehci *)OMAP_EHCI_BASE; static int omap_uhh_reset(void) { - unsigned long init = get_timer(0); - - /* perform UHH soft reset, and wait until reset is complete */ - writel(OMAP_UHH_SYSCONFIG_SOFTRESET, &uhh->sysc); - - /* Wait for UHH reset to complete */ - while (!(readl(&uhh->syss) & OMAP_UHH_SYSSTATUS_EHCI_RESETDONE)) - if (get_timer(init) > CONFIG_SYS_HZ) { - debug("OMAP UHH error: timeout resetting ehci\n"); - return -EL3RST; - } - +/* + * Soft resetting the UHH module causes instability issues on + * all OMAPs so we just avoid it. + * + * See OMAP36xx Errata + * i571: USB host EHCI may stall when entering smart-standby mode + * i660: USBHOST Configured In Smart-Idle Can Lead To a Deadlock + * + * On OMAP4/5, soft-resetting the UHH module will put it into + * Smart-Idle mode and lead to a deadlock. + * + * On OMAP3, this doesn't seem to be the case but still instabilities + * are observed on beagle (3530 ES1.0) if soft-reset is used. + * e.g. NFS root failures with Linux kernel. + */ return 0; } @@ -76,6 +79,7 @@ static void omap_usbhs_hsic_init(int port) writel(reg, &usbtll->channel_conf + port); } +#ifdef CONFIG_USB_ULPI static void omap_ehci_soft_phy_reset(int port) { struct ulpi_viewport ulpi_vp; @@ -85,6 +89,12 @@ static void omap_ehci_soft_phy_reset(int port) ulpi_reset(&ulpi_vp); } +#else +static void omap_ehci_soft_phy_reset(int port) +{ + return; +} +#endif inline int __board_usb_init(void) { @@ -93,7 +103,8 @@ inline int __board_usb_init(void) int board_usb_init(void) __attribute__((weak, alias("__board_usb_init"))); #if defined(CONFIG_OMAP_EHCI_PHY1_RESET_GPIO) || \ - defined(CONFIG_OMAP_EHCI_PHY2_RESET_GPIO) + defined(CONFIG_OMAP_EHCI_PHY2_RESET_GPIO) || \ + defined(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO) /* controls PHY(s) reset signal(s) */ static inline void omap_ehci_phy_reset(int on, int delay) { @@ -112,6 +123,10 @@ static inline void omap_ehci_phy_reset(int on, int delay) gpio_request(CONFIG_OMAP_EHCI_PHY2_RESET_GPIO, "USB PHY2 reset"); gpio_direction_output(CONFIG_OMAP_EHCI_PHY2_RESET_GPIO, !on); #endif +#ifdef CONFIG_OMAP_EHCI_PHY3_RESET_GPIO + gpio_request(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, "USB PHY3 reset"); + gpio_direction_output(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, !on); +#endif /* Hold the PHY in RESET for enough time till DIR is high */ /* Refer: ISSUE1 */ @@ -195,10 +210,27 @@ int omap_ehci_hcd_init(struct omap_usbhs_board_data *usbhs_pdata, else setbits_le32(®, OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS); } else if (rev == OMAP_USBHS_REV2) { + clrsetbits_le32(®, (OMAP_P1_MODE_CLEAR | OMAP_P2_MODE_CLEAR), OMAP4_UHH_HOSTCONFIG_APP_START_CLK); - /* Clear port mode fields for PHY mode*/ + /* Clear port mode fields for PHY mode */ + + if (is_ehci_hsic_mode(usbhs_pdata->port_mode[0])) + setbits_le32(®, OMAP_P1_MODE_HSIC); + + if (is_ehci_hsic_mode(usbhs_pdata->port_mode[1])) + setbits_le32(®, OMAP_P2_MODE_HSIC); + + } else if (rev == OMAP_USBHS_REV2_1) { + + clrsetbits_le32(®, + (OMAP_P1_MODE_CLEAR | + OMAP_P2_MODE_CLEAR | + OMAP_P3_MODE_CLEAR), + OMAP4_UHH_HOSTCONFIG_APP_START_CLK); + + /* Clear port mode fields for PHY mode */ if (is_ehci_hsic_mode(usbhs_pdata->port_mode[0])) setbits_le32(®, OMAP_P1_MODE_HSIC); |