diff options
Diffstat (limited to 'include/configs/RPXsuper.h')
| -rw-r--r-- | include/configs/RPXsuper.h | 501 |
1 files changed, 0 insertions, 501 deletions
diff --git a/include/configs/RPXsuper.h b/include/configs/RPXsuper.h deleted file mode 100644 index f5e0968011..0000000000 --- a/include/configs/RPXsuper.h +++ /dev/null @@ -1,501 +0,0 @@ -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_SYS_TEXT_BASE 0x80F00000 - -/***************************************************************************** - * - * These settings must match the way _your_ board is set up - * - *****************************************************************************/ -/* for the AY-Revision which does not use the HRCW */ -#define CONFIG_SYS_DEFAULT_IMMR 0x00010000 - -/* What is the oscillator's (UX2) frequency in Hz? */ -#define CONFIG_8260_CLKIN (66 * 1000 * 1000) - -/* How is switch S2 set? We really only want the MODCK[1-3] bits, so - * only the 3 least significant bits are important. -*/ -#define CONFIG_SYS_SBC_S2 0x04 - -/* What should MODCK_H be? It is dependent on the oscillator - * frequency, MODCK[1-3], and desired CPM and core frequencies. - * Some example values (all frequencies are in MHz): - * - * MODCK_H MODCK[1-3] Osc CPM Core - * 0x2 0x2 33 133 133 - * 0x2 0x4 33 133 200 - * 0x5 0x5 66 133 133 - * 0x5 0x7 66 133 200 - */ -#define CONFIG_SYS_SBC_MODCK_H 0x06 - -#define CONFIG_SYS_SBC_BOOT_LOW 1 /* only for HRCW */ -#undef CONFIG_SYS_SBC_BOOT_LOW - -/* What should the base address of the main FLASH be and how big is - * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE. - * The main FLASH is whichever is connected to *CS0. U-Boot expects - * this to be the SIMM. - */ -#define CONFIG_SYS_FLASH0_BASE 0x80000000 -#define CONFIG_SYS_FLASH0_SIZE 16 - -/* What should the base address of the secondary FLASH be and how big - * is it (in Mbytes)? The secondary FLASH is whichever is connected - * to *CS6. U-Boot expects this to be the on board FLASH. If you don't - * want it enabled, don't define these constants. - */ -#define CONFIG_SYS_FLASH1_BASE 0 -#define CONFIG_SYS_FLASH1_SIZE 0 -#undef CONFIG_SYS_FLASH1_BASE -#undef CONFIG_SYS_FLASH1_SIZE - -/* What should be the base address of SDRAM DIMM and how big is - * it (in Mbytes)? -*/ -#define CONFIG_SYS_SDRAM0_BASE 0x00000000 -#define CONFIG_SYS_SDRAM0_SIZE 64 - -/* What should be the base address of SDRAM DIMM and how big is - * it (in Mbytes)? -*/ -#define CONFIG_SYS_SDRAM1_BASE 0x04000000 -#define CONFIG_SYS_SDRAM1_SIZE 32 - -/* What should be the base address of the LEDs and switch S0? - * If you don't want them enabled, don't define this. - */ -#define CONFIG_SYS_LED_BASE 0x00000000 - -/* - * select serial console configuration - * - * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - * - * if CONFIG_CONS_NONE is defined, then the serial console routines must - * defined elsewhere. - */ -#define CONFIG_CONS_ON_SMC /* define if console on SMC */ -#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on neither */ -#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */ - -/* - * select ethernet configuration - * - * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then - * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 - * for FCC) - * - * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be - * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. - */ -#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */ -#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */ -#undef CONFIG_ETHER_NONE /* define if ethernet on neither */ -#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */ - -#if ( CONFIG_ETHER_INDEX == 3 ) - -/* - * - Rx-CLK is CLK15 - * - Tx-CLK is CLK16 - * - RAM for BD/Buffers is on the 60x Bus (see 28-13) - * - Enable Half Duplex in FSMR - */ -# define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK) -# define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16) -# define CONFIG_SYS_CPMFCR_RAMTYPE 0 -/*#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */ -# define CONFIG_SYS_FCC_PSMR 0 - -#else /* CONFIG_ETHER_INDEX */ -# error "on RPX Super ethernet must be FCC3" -#endif /* CONFIG_ETHER_INDEX */ - -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - - -/* Define this to reserve an entire FLASH sector (256 KB) for - * environment variables. Otherwise, the environment will be - * put in the same sector as U-Boot, and changing variables - * will erase U-Boot temporarily - */ -#define CONFIG_ENV_IN_OWN_SECT - -/* Define to allow the user to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* What should the console's baud rate be? */ -#define CONFIG_BAUDRATE 115200 - -/* Ethernet MAC address */ -#define CONFIG_ETHADDR 08:00:22:50:70:63 - -#define CONFIG_IPADDR 192.168.1.99 -#define CONFIG_SERVERIP 192.168.1.3 - -/* Set to a positive value to delay for running BOOTCOMMAND */ -#define CONFIG_BOOTDELAY -1 - -/* undef this to save memory */ -#define CONFIG_SYS_LONGHELP - -/* Monitor Command Prompt */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_I2C -#define CONFIG_CMD_REGINFO - -#undef CONFIG_CMD_KGDB - - -/* Where do the internal registers live? */ -#define CONFIG_SYS_IMMR 0xF0000000 - -/* Where do the on board registers (CS4) live? */ -#define CONFIG_SYS_REGS_BASE 0xFA000000 - -/***************************************************************************** - * - * You should not have to modify any of the following settings - * - *****************************************************************************/ - -#define CONFIG_RPXSUPER 1 /* on an Embedded Planet RPX Super Board */ -#define CONFIG_CPM2 1 /* Has a CPM2 */ - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ - -/* - * Miscellaneous configurable options - */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) - -#define CONFIG_SYS_MAXARGS 8 /* max number of command args */ - -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x04000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */ - -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ - -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE - -/*----------------------------------------------------------------------- - * Hard Reset Configuration Words - */ -#if defined(CONFIG_SYS_SBC_BOOT_LOW) -# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS) -#else -# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0) -#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */ - -/* get the HRCW ISB field from CONFIG_SYS_IMMR */ -#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) |\ - ((CONFIG_SYS_IMMR & 0x01000000) >> 7) |\ - ((CONFIG_SYS_IMMR & 0x00100000) >> 4) ) - -#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS11 |\ - HRCW_DPPC11 |\ - CONFIG_SYS_SBC_HRCW_IMMR |\ - HRCW_MMR00 |\ - HRCW_LBPC11 |\ - HRCW_APPC10 |\ - HRCW_CS10PC00 |\ - (CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) |\ - CONFIG_SYS_SBC_HRCW_BOOT_FLAGS) - -/* no slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent. - */ -#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH0_BASE + 0x00F00000) - -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ - -#ifndef CONFIG_SYS_RAMBOOT -# define CONFIG_ENV_IS_IN_FLASH 1 - -# ifdef CONFIG_ENV_IN_OWN_SECT -# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) -# define CONFIG_ENV_SECT_SIZE 0x40000 -# else -# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE) -# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */ -# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */ -# endif /* CONFIG_ENV_IN_OWN_SECT */ -#else -# define CONFIG_ENV_IS_IN_NVRAM 1 -# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -# define CONFIG_ENV_SIZE 0x200 -#endif /* CONFIG_SYS_RAMBOOT */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ - -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * HIDx - Hardware Implementation-dependent Registers 2-11 - *----------------------------------------------------------------------- - * HID0 also contains cache control - initially enable both caches and - * invalidate contents, then the final state leaves only the instruction - * cache enabled. Note that Power-On and Hard reset invalidate the caches, - * but Soft reset does not. - * - * HID1 has only read-only information - nothing to set. - */ -#define CONFIG_SYS_HID0_INIT (/*HID0_ICE |*/\ - /*HID0_DCE |*/\ - HID0_ICFI |\ - HID0_DCI |\ - HID0_IFEM |\ - HID0_ABE) - -#define CONFIG_SYS_HID0_FINAL (/*HID0_ICE |*/\ - HID0_IFEM |\ - HID0_ABE |\ - HID0_EMCP) -#define CONFIG_SYS_HID2 0 - -/*----------------------------------------------------------------------- - * RMR - Reset Mode Register - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RMR 0 - -/*----------------------------------------------------------------------- - * BCR - Bus Configuration 4-25 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_BCR (BCR_EBM |\ - BCR_PLDP |\ - BCR_EAV |\ - BCR_NPQM0) - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 4-31 - *----------------------------------------------------------------------- - */ - -#define CONFIG_SYS_SIUMCR (SIUMCR_L2CPC01 |\ - SIUMCR_APPC10 |\ - SIUMCR_CS10PC01) - - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable - */ -#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\ - SYPCR_BMT |\ - SYPCR_PBME |\ - SYPCR_LBME |\ - SYPCR_SWRI |\ - SYPCR_SWP) - -/*----------------------------------------------------------------------- - * TMCNTSC - Time Counter Status and Control 4-40 - *----------------------------------------------------------------------- - * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, - * and enable Time Counter - */ -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\ - TMCNTSC_ALR |\ - TMCNTSC_TCF |\ - TMCNTSC_TCE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 4-42 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable - * Periodic timer - */ -#define CONFIG_SYS_PISCR (PISCR_PS |\ - PISCR_PTF |\ - PISCR_PTE) - -/*----------------------------------------------------------------------- - * SCCR - System Clock Control 9-8 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_SCCR (SCCR_DFBRG01) - -/*----------------------------------------------------------------------- - * RCCR - RISC Controller Configuration 13-7 - *----------------------------------------------------------------------- - */ -#define CONFIG_SYS_RCCR 0 - -/* - * Init Memory Controller: - * - * Bank Bus Machine PortSz Device - * ---- --- ------- ------ ------ - * 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90) - * 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Hitachi HM5225325FBP-B60) - * 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Hitachi HM5225325FBP-B60) - * 3 unused - * 4 60x GPCM 8 bit Board Regs, LEDs, switches - * 5 unused - * 6 unused - * 7 unused - * 8 PCMCIA - * 9 unused - * 10 unused - * 11 unused -*/ - -/* Bank 0 - FLASH - * - */ -#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_DECC_NONE |\ - BRx_MS_GPCM_P |\ - BRx_V) - -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\ - ORxG_CSNT |\ - ORxG_ACS_DIV1 |\ - ORxG_SCY_6_CLK |\ - ORxG_EHTR) - -/* Bank 1 - SDRAM - * - */ -#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\ - BRx_PS_64 |\ - BRx_MS_SDRAM_P |\ - BRx_V) - -#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI0_A8 |\ - ORxS_NUMR_12 |\ - ORxS_IBID) - -#define CONFIG_SYS_PSDMR 0x014DA412 -#define CONFIG_SYS_PSRT 0x79 - - -/* Bank 2 - SDRAM - * - */ -#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\ - BRx_PS_32 |\ - BRx_MS_SDRAM_L |\ - BRx_V) - -#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) |\ - ORxS_BPD_4 |\ - ORxS_ROWST_PBI0_A9 |\ - ORxS_NUMR_12) - -#define CONFIG_SYS_LSDMR 0x0169A512 -#define CONFIG_SYS_LSRT 0x79 - -#define CONFIG_SYS_MPTPR (0x0800 & MPTPR_PTP_MSK) - -/* Bank 4 - On board registers - * - */ -#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\ - BRx_PS_8 |\ - BRx_MS_GPCM_P |\ - BRx_V) - -#define CONFIG_SYS_OR4_PRELIM (ORxG_AM_MSK |\ - ORxG_CSNT |\ - ORxG_ACS_DIV1 |\ - ORxG_SCY_5_CLK |\ - ORxG_TRLX) - -#endif /* __CONFIG_H */ |