diff options
Diffstat (limited to 'include/configs/a4m072.h')
| -rw-r--r-- | include/configs/a4m072.h | 324 |
1 files changed, 0 insertions, 324 deletions
diff --git a/include/configs/a4m072.h b/include/configs/a4m072.h deleted file mode 100644 index 6a26269807..0000000000 --- a/include/configs/a4m072.h +++ /dev/null @@ -1,324 +0,0 @@ -/* - * (C) Copyright 2003-2005 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2010 - * Sergei Poselenov, Emcraft Systems, sposelenov@emcraft.com. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */ -#define CONFIG_A4M072 1 /* ... on A4M072 board */ -#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */ - -#define CONFIG_SYS_TEXT_BASE 0xFE000000 - -#define CONFIG_MISC_INIT_R - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } -/* define to enable silent console */ -#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ - -#if defined(CONFIG_PCI) -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 -#endif - -#define CONFIG_SYS_XLB_PIPELINING 1 - -#undef CONFIG_EEPRO100 - -/* USB */ -#define CONFIG_USB_OHCI_NEW -#define CONFIG_SYS_OHCI_BE_CONTROLLER -#undef CONFIG_SYS_USB_OHCI_BOARD_INIT -#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 -#define CONFIG_SYS_USB_OHCI_REGS_BASE MPC5XXX_USB -#define CONFIG_SYS_USB_OHCI_SLOT_NAME "mpc5200" -#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 - -#define CONFIG_TIMESTAMP /* Print image info with timestamp */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ - -#if defined(CONFIG_PCI) -#define CONFIG_CMD_PCI -#endif - -#if (CONFIG_SYS_TEXT_BASE == 0xFE000000) /* Boot low with 32 MB Flash */ -#define CONFIG_SYS_LOWBOOT 1 -#define CONFIG_SYS_LOWBOOT32 1 -#endif - -/* - * Autobooting - */ - -#define CONFIG_SYS_AUTOLOAD "n" - -#undef CONFIG_BOOTARGS -#define CONFIG_PREBOOT "run try_update" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "bk=run add_mtd ; run add_consolespec ; bootm 200000\0" \ - "cf1=diskboot 200000 0:1\0" \ - "bootcmd_cf1=run bcf1\0" \ - "bcf=setenv bootargs root=/dev/hda3\0" \ - "bootcmd_nfs=run bnfs\0" \ - "norargs=setenv bootargs root=/dev/mtdblock3 rootfstype=cramfs "\ - "panic=1\0" \ - "bootcmd_nor=cp.b ${kernel_addr} 200000 100000;" \ - "run norargs addip; run bk\0" \ - "bnfs=nfs 200000 ${rootpath}/boot/uImage;" \ - "run nfsargs addip ; run bk\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "try_update=usb start;sleep 2;usb start;sleep 1;" \ - "fatload usb 0 2F0000 PCPUUPDT 2FF;usb stop;" \ - "source 2F0000\0" \ - "env_addr=FE060000\0" \ - "kernel_addr=FE100000\0" \ - "rootfs_addr=FE200000\0" \ - "add_mtd=setenv bootargs ${bootargs} mtdparts=" \ - "phys_mapped_flash:384k(u),640k(e),1m(k),30m(r)\0" \ - "bcf1=run cf1; run bcf; run addip; run bk\0" \ - "add_consolespec=setenv bootargs ${bootargs} " \ - "console=/dev/null quiet\0" \ - "addip=if test -n ${ethaddr};" \ - "then if test -n ${ipaddr};" \ - "then setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:"\ - "${netmask}:${hostname}:${netdev}:off;" \ - "fi;" \ - "else;" \ - "setenv bootargs ${bootargs} no_ethaddr;" \ - "fi\0" \ - "hostname=CPUP0\0" \ - "netdev=eth0\0" \ - "bootcmd=run bootcmd_nor\0" \ - "" -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ - -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_FLASH_SIZE 0x02000000 -#if !defined(CONFIG_SYS_LOWBOOT) -#error "CONFIG_SYS_LOWBOOT not defined?" -#else /* CONFIG_SYS_LOWBOOT */ -#if defined(CONFIG_SYS_LOWBOOT32) -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) -#endif -#endif /* CONFIG_SYS_LOWBOOT */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_CS0_START} -#define CONFIG_SYS_FLASH_BANKS_SIZES {CONFIG_SYS_CS0_SIZE} - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -#define CONFIG_ENV_OVERWRITE 1 - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -/* - * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb - */ -/* #define CONFIG_MPC5xxx_FEC_MII10 */ -#define CONFIG_PHY_ADDR 0x1f -#define CONFIG_PHY_TYPE 0x79c874 /* AMD Phy Controller */ - -/* - * GPIO configuration - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x18000004 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_CMDLINE_EDITING 1 -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE -/* Flash at CSBoot, CS0 */ -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x0002DD00 -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE -/* External SRAM at CS1 */ -#define CONFIG_SYS_CS1_START 0x62000000 -#define CONFIG_SYS_CS1_SIZE 0x00400000 -#define CONFIG_SYS_CS1_CFG 0x00009930 -#define CONFIG_SYS_SRAM_BASE CONFIG_SYS_CS1_START -#define CONFIG_SYS_SRAM_SIZE CONFIG_SYS_CS1_SIZE -/* LED display at CS7 */ -#define CONFIG_SYS_CS7_START 0x6a000000 -#define CONFIG_SYS_CS7_SIZE (64*1024) -#define CONFIG_SYS_CS7_CFG 0x0000bf30 - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333003 - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 /* 0x4000 for SE mode */ - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 2 drives per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#define CONFIG_ATAPI 1 - -/*----------------------------------------------------------------------- - * Open firmware flat tree support - *----------------------------------------------------------------------- - */ -#define OF_CPU "PowerPC,5200@0" -#define OF_SOC "soc5200@f0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" - -/* Support for the 7-segment display */ -#define CONFIG_SYS_DISP_CHR_RAM CONFIG_SYS_CS7_START -#define CONFIG_SHOW_ACTIVITY /* used for display realization */ - -#define CONFIG_SHOW_BOOT_PROGRESS - -#endif /* __CONFIG_H */ |