diff options
Diffstat (limited to 'include/configs/aria.h')
-rw-r--r-- | include/configs/aria.h | 591 |
1 files changed, 0 insertions, 591 deletions
diff --git a/include/configs/aria.h b/include/configs/aria.h deleted file mode 100644 index 0a7ef9919e..0000000000 --- a/include/configs/aria.h +++ /dev/null @@ -1,591 +0,0 @@ -/* - * (C) Copyright 2009 Wolfgang Denk <wd@denx.de> - * (C) Copyright 2009, DAVE Srl <www.dave.eu> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * Aria board configuration file - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_ARIA 1 - -/* - * Memory map for the ARIA board: - * - * 0x0000_0000-0x0FFF_FFFF DDR RAM (256 MB) - * 0x3000_0000-0x3001_FFFF On Chip SRAM (128 KB) - * 0x3010_0000-0x3011_FFFF On Board SRAM (128 KB) - CS6 - * 0x3020_0000-0x3021_FFFF FPGA (128 KB) - CS2 - * 0x8000_0000-0x803F_FFFF IMMR (4 MB) - * 0x8400_0000-0x82FF_FFFF PCI I/O space (16 MB) - * 0xA000_0000-0xAFFF_FFFF PCI memory space (256 MB) - * 0xB000_0000-0xBFFF_FFFF PCI memory mapped I/O space (256 MB) - * 0xFC00_0000-0xFFFF_FFFF NOR Boot FLASH (64 MB) - */ - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 /* E300 Family */ -#define CONFIG_FSL_DIU_FB 1 /* FSL DIU */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -/* video */ - -/* CONFIG_PCI is defined at config time */ - -#define CONFIG_SYS_MPC512X_CLKIN 33000000 /* in Hz */ - -#define CONFIG_MISC_INIT_R - -#define CONFIG_SYS_IMMR 0x80000000 -#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_IMMR+0x2100) - -#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ -#define CONFIG_SYS_MEMTEST_END 0x00400000 - -/* - * DDR Setup - manually set all parameters as there's no SPD etc. - */ -#define CONFIG_SYS_DDR_SIZE 256 /* MB */ -#define CONFIG_SYS_DDR_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_MAX_RAM_SIZE 0x20000000 - -#define CONFIG_SYS_IOCTRL_MUX_DDR 0x00000036 - -/* DDR Controller Configuration - * - * SYS_CFG: - * [31:31] MDDRC Soft Reset: Diabled - * [30:30] DRAM CKE pin: Enabled - * [29:29] DRAM CLK: Enabled - * [28:28] Command Mode: Enabled (For initialization only) - * [27:25] DRAM Row Select: dram_row[15:0] = magenta_address[25:10] - * [24:21] DRAM Bank Select: dram_bank[1:0] = magenta_address[11:10] - * [20:19] Read Test: DON'T USE - * [18:18] Self Refresh: Enabled - * [17:17] 16bit Mode: Disabled - * [16:13] Ready Delay: 2 - * [12:12] Half DQS Delay: Disabled - * [11:11] Quarter DQS Delay: Disabled - * [10:08] Write Delay: 2 - * [07:07] Early ODT: Disabled - * [06:06] On DIE Termination: Disabled - * [05:05] FIFO Overflow Clear: DON'T USE here - * [04:04] FIFO Underflow Clear: DON'T USE here - * [03:03] FIFO Overflow Pending: DON'T USE here - * [02:02] FIFO Underlfow Pending: DON'T USE here - * [01:01] FIFO Overlfow Enabled: Enabled - * [00:00] FIFO Underflow Enabled: Enabled - * TIME_CFG0 - * [31:16] DRAM Refresh Time: 0 CSB clocks - * [15:8] DRAM Command Time: 0 CSB clocks - * [07:00] DRAM Precharge Time: 0 CSB clocks - * TIME_CFG1 - * [31:26] DRAM tRFC: - * [25:21] DRAM tWR1: - * [20:17] DRAM tWRT1: - * [16:11] DRAM tDRR: - * [10:05] DRAM tRC: - * [04:00] DRAM tRAS: - * TIME_CFG2 - * [31:28] DRAM tRCD: - * [27:23] DRAM tFAW: - * [22:19] DRAM tRTW1: - * [18:15] DRAM tCCD: - * [14:10] DRAM tRTP: - * [09:05] DRAM tRP: - * [04:00] DRAM tRPA - */ -#define CONFIG_SYS_MDDRC_SYS_CFG ( (1 << 31) | /* RST_B */ \ - (1 << 30) | /* CKE */ \ - (1 << 29) | /* CLK_ON */ \ - (0 << 28) | /* CMD_MODE */ \ - (4 << 25) | /* DRAM_ROW_SELECT */ \ - (3 << 21) | /* DRAM_BANK_SELECT */ \ - (0 << 18) | /* SELF_REF_EN */ \ - (0 << 17) | /* 16BIT_MODE */ \ - (2 << 13) | /* RDLY */ \ - (0 << 12) | /* HALF_DQS_DLY */ \ - (1 << 11) | /* QUART_DQS_DLY */ \ - (2 << 8) | /* WDLY */ \ - (0 << 7) | /* EARLY_ODT */ \ - (1 << 6) | /* ON_DIE_TERMINATE */ \ - (0 << 5) | /* FIFO_OV_CLEAR */ \ - (0 << 4) | /* FIFO_UV_CLEAR */ \ - (0 << 1) | /* FIFO_OV_EN */ \ - (0 << 0) /* FIFO_UV_EN */ \ - ) - -#define CONFIG_SYS_MDDRC_TIME_CFG0 0x030C3D2E -#define CONFIG_SYS_MDDRC_TIME_CFG1 0x55D81189 -#define CONFIG_SYS_MDDRC_TIME_CFG2 0x34790863 - -#define CONFIG_SYS_DDRCMD_NOP 0x01380000 -#define CONFIG_SYS_DDRCMD_PCHG_ALL 0x01100400 -#define CONFIG_SYS_MICRON_EMR ( (1 << 24) | /* CMD_REQ */ \ - (0 << 22) | /* DRAM_CS */ \ - (0 << 21) | /* DRAM_RAS */ \ - (0 << 20) | /* DRAM_CAS */ \ - (0 << 19) | /* DRAM_WEB */ \ - (1 << 16) | /* DRAM_BS[2:0] */ \ - (0 << 15) | /* */ \ - (0 << 12) | /* A12->out */ \ - (0 << 11) | /* A11->RDQS */ \ - (0 << 10) | /* A10->DQS# */ \ - (0 << 7) | /* OCD program */ \ - (0 << 6) | /* Rtt1 */ \ - (0 << 3) | /* posted CAS# */ \ - (0 << 2) | /* Rtt0 */ \ - (1 << 1) | /* ODS */ \ - (0 << 0) /* DLL */ \ - ) -#define CONFIG_SYS_MICRON_EMR2 0x01020000 -#define CONFIG_SYS_MICRON_EMR3 0x01030000 -#define CONFIG_SYS_DDRCMD_RFSH 0x01080000 -#define CONFIG_SYS_MICRON_INIT_DEV_OP 0x01000432 -#define CONFIG_SYS_MICRON_EMR_OCD ( (1 << 24) | /* CMD_REQ */ \ - (0 << 22) | /* DRAM_CS */ \ - (0 << 21) | /* DRAM_RAS */ \ - (0 << 20) | /* DRAM_CAS */ \ - (0 << 19) | /* DRAM_WEB */ \ - (1 << 16) | /* DRAM_BS[2:0] */ \ - (0 << 15) | /* */ \ - (0 << 12) | /* A12->out */ \ - (0 << 11) | /* A11->RDQS */ \ - (1 << 10) | /* A10->DQS# */ \ - (7 << 7) | /* OCD program */ \ - (0 << 6) | /* Rtt1 */ \ - (0 << 3) | /* posted CAS# */ \ - (1 << 2) | /* Rtt0 */ \ - (0 << 1) | /* ODS (Output Drive Strength) */ \ - (0 << 0) /* DLL */ \ - ) - -/* - * Backward compatible definitions, - * so we do not have to change arch/powerpc/cpu/mpc512x/fixed_sdram.c - */ -#define CONFIG_SYS_DDRCMD_EM2 (CONFIG_SYS_MICRON_EMR2) -#define CONFIG_SYS_DDRCMD_EM3 (CONFIG_SYS_MICRON_EMR3) -#define CONFIG_SYS_DDRCMD_EN_DLL (CONFIG_SYS_MICRON_EMR) -#define CONFIG_SYS_DDRCMD_OCD_DEFAULT (CONFIG_SYS_MICRON_EMR_OCD) - -/* DDR Priority Manager Configuration */ -#define CONFIG_SYS_MDDRCGRP_PM_CFG1 0x00077777 -#define CONFIG_SYS_MDDRCGRP_PM_CFG2 0x00000000 -#define CONFIG_SYS_MDDRCGRP_HIPRIO_CFG 0x00000001 -#define CONFIG_SYS_MDDRCGRP_LUT0_MU 0xFFEEDDCC -#define CONFIG_SYS_MDDRCGRP_LUT0_ML 0xBBAAAAAA -#define CONFIG_SYS_MDDRCGRP_LUT1_MU 0x66666666 -#define CONFIG_SYS_MDDRCGRP_LUT1_ML 0x55555555 -#define CONFIG_SYS_MDDRCGRP_LUT2_MU 0x44444444 -#define CONFIG_SYS_MDDRCGRP_LUT2_ML 0x44444444 -#define CONFIG_SYS_MDDRCGRP_LUT3_MU 0x55555555 -#define CONFIG_SYS_MDDRCGRP_LUT3_ML 0x55555558 -#define CONFIG_SYS_MDDRCGRP_LUT4_MU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT4_ML 0x11111122 -#define CONFIG_SYS_MDDRCGRP_LUT0_AU 0xaaaaaaaa -#define CONFIG_SYS_MDDRCGRP_LUT0_AL 0xaaaaaaaa -#define CONFIG_SYS_MDDRCGRP_LUT1_AU 0x66666666 -#define CONFIG_SYS_MDDRCGRP_LUT1_AL 0x66666666 -#define CONFIG_SYS_MDDRCGRP_LUT2_AU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT2_AL 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT3_AU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT3_AL 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT4_AU 0x11111111 -#define CONFIG_SYS_MDDRCGRP_LUT4_AL 0x11111111 - -/* - * NOR FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_CFI /* use the CFI code */ -#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ -#define CONFIG_SYS_FLASH_BASE 0xF8000000 /* start of FLASH */ -#define CONFIG_SYS_FLASH_SIZE 0x08000000 /* max flash size */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* max sectors */ - -#undef CONFIG_SYS_FLASH_CHECKSUM - -/* - * NAND FLASH support - * drivers/mtd/nand/mpc5121_nfc.c (rev 2 silicon only) - */ -#define CONFIG_CMD_NAND /* enable NAND support */ -#define CONFIG_JFFS2_NAND /* with JFFS2 on it */ -#define CONFIG_NAND_MPC5121_NFC -#define CONFIG_SYS_NAND_BASE 0x40000000 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 - -/* - * Configuration parameters for MPC5121 NAND driver - */ -#define CONFIG_FSL_NFC_WIDTH 1 -#define CONFIG_FSL_NFC_WRITE_SIZE 2048 -#define CONFIG_FSL_NFC_SPARE_SIZE 64 -#define CONFIG_FSL_NFC_CHIPS CONFIG_SYS_MAX_NAND_DEVICE - -#define CONFIG_SYS_SRAM_BASE 0x30000000 -#define CONFIG_SYS_SRAM_SIZE 0x00020000 /* 128 KB */ - -/* Make two SRAM regions contiguous */ -#define CONFIG_SYS_ARIA_SRAM_BASE (CONFIG_SYS_SRAM_BASE + \ - CONFIG_SYS_SRAM_SIZE) -#define CONFIG_SYS_ARIA_SRAM_SIZE 0x00100000 /* reserve 1MB-window */ -#define CONFIG_SYS_CS6_START CONFIG_SYS_ARIA_SRAM_BASE -#define CONFIG_SYS_CS6_SIZE CONFIG_SYS_ARIA_SRAM_SIZE - -#define CONFIG_SYS_ARIA_FPGA_BASE (CONFIG_SYS_ARIA_SRAM_BASE + \ - CONFIG_SYS_ARIA_SRAM_SIZE) -#define CONFIG_SYS_ARIA_FPGA_SIZE 0x20000 /* 128 KB */ - -#define CONFIG_SYS_CS2_START CONFIG_SYS_ARIA_FPGA_BASE -#define CONFIG_SYS_CS2_SIZE CONFIG_SYS_ARIA_FPGA_SIZE - -#define CONFIG_SYS_CS0_CFG 0x05059150 -#define CONFIG_SYS_CS2_CFG ( (5 << 24) | \ - (5 << 16) | \ - (1 << 15) | \ - (0 << 14) | \ - (0 << 13) | \ - (1 << 12) | \ - (0 << 10) | \ - (3 << 8) | /* 32 bit */ \ - (0 << 7) | \ - (1 << 6) | \ - (1 << 4) | \ - (0 << 3) | \ - (0 << 2) | \ - (0 << 1) | \ - (0 << 0) \ - ) -#define CONFIG_SYS_CS6_CFG 0x05059150 - -/* Use alternative CS timing for CS0 and CS2 */ -#define CONFIG_SYS_CS_ALETIMING 0x00000005 - -/* Use SRAM for initial stack */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SRAM_BASE -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_SRAM_SIZE - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (384 * 1024) - -#ifdef CONFIG_FSL_DIU_FB -#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) -#else -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) -#endif - -/* FPGA */ -#define CONFIG_ARIA_FPGA 1 - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 - -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 3 /* console on PSC3 */ -#define CONFIG_SYS_PSC3 -#if CONFIG_PSC_CONSOLE != 3 -#error CONFIG_PSC_CONSOLE must be 3 -#endif - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} - -#define CONSOLE_FIFO_TX_SIZE FIFOC_PSC3_TX_SIZE -#define CONSOLE_FIFO_TX_ADDR FIFOC_PSC3_TX_ADDR -#define CONSOLE_FIFO_RX_SIZE FIFOC_PSC3_RX_SIZE -#define CONSOLE_FIFO_RX_ADDR FIFOC_PSC3_RX_ADDR - -#define CONFIG_CMDLINE_EDITING 1 /* command line history */ - -/* - * PCI - */ -#ifdef CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE - -#define CONFIG_SYS_PCI_MEM_BASE 0xA0000000 -#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE -#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI_MMIO_BASE (CONFIG_SYS_PCI_MEM_BASE + \ - CONFIG_SYS_PCI_MEM_SIZE) -#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE -#define CONFIG_SYS_PCI_MMIO_SIZE 0x10000000 /* 256M */ -#define CONFIG_SYS_PCI_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI_IO_PHYS 0x84000000 -#define CONFIG_SYS_PCI_IO_SIZE 0x01000000 /* 16M */ - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ - -#endif - -/* - * IIM - IC Identification Module - */ -#undef CONFIG_FSL_IIM - -/* - * Ethernet configuration - */ -#define CONFIG_MPC512x_FEC 1 -#define CONFIG_PHY_ADDR 0x17 -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_FEC_AN_TIMEOUT 1 -#define CONFIG_HAS_ETH0 - -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -/* This has to be a multiple of the flash sector size */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ - CONFIG_SYS_MONITOR_LEN) -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* one sector (256K) */ - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + \ - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) - -#define CONFIG_LOADS_ECHO 1 -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 - -#define CONFIG_CMD_REGINFO - -#if defined(CONFIG_PCI) -#define CONFIG_CMD_PCI -#endif - -/* - * Dynamic MTD partition support - */ -#define CONFIG_CMD_MTDPARTS -#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ -#define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=f8000000.flash,nand0=mpc5121.nand" - -/* - * NOR flash layout: - * - * F8000000 - FEAFFFFF 107 MiB User Data - * FEB00000 - FFAFFFFF 16 MiB Root File System - * FFB00000 - FFFEFFFF 4 MiB Linux Kernel - * FFF00000 - FFFBFFFF 768 KiB U-Boot (up to 512 KiB) and 2 x * env - * FFFC0000 - FFFFFFFF 256 KiB Device Tree - * - * NAND flash layout: one big partition - */ -#define MTDPARTS_DEFAULT "mtdparts=f8000000.flash:107m(user)," \ - "16m(rootfs)," \ - "4m(kernel)," \ - "768k(u-boot)," \ - "256k(dtb);" \ - "mpc5121.nand:-(data)" - -/* - * Watchdog timeout = CONFIG_SYS_WATCHDOG_VALUE * 65536 / IPS clock. - * For example, when IPS is set to 66MHz and CONFIG_SYS_WATCHDOG_VALUE - * is set to 0xFFFF, watchdog timeouts after about 64s. For details - * refer to chapter 36 of the MPC5121e Reference Manual. - */ -/* #define CONFIG_WATCHDOG */ /* enable watchdog */ -#define CONFIG_SYS_WATCHDOG_VALUE 0xFFFF - - /* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ - -#ifdef CONFIG_CMD_KGDB -# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif - -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 32 -/* Boot Argument Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) - -/* Cache Configuration */ -#define CONFIG_SYS_DCACHE_SIZE 32768 -#define CONFIG_SYS_CACHELINE_SIZE 32 -#ifdef CONFIG_CMD_KGDB -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of 32 */ -#endif - -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ - HID0_ICE) -#define CONFIG_SYS_HID2 HID2_HBE - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ - -#ifdef CONFIG_CMD_KGDB -#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ -#endif - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_TIMESTAMP - -#define CONFIG_HOSTNAME aria -#define CONFIG_BOOTFILE "aria/uImage" -#define CONFIG_ROOTPATH "/opt/eldk/ppc_6xx" - -#define CONFIG_LOADADDR 400000 /* default load addr */ - -#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "u-boot_addr_r=200000\0" \ - "kernel_addr_r=600000\0" \ - "fdt_addr_r=880000\0" \ - "ramdisk_addr_r=900000\0" \ - "u-boot_addr=FFF00000\0" \ - "kernel_addr=FFB00000\0" \ - "fdt_addr=FFFC0000\0" \ - "ramdisk_addr=FEB00000\0" \ - "ramdiskfile=aria/uRamdisk\0" \ - "u-boot=aria/u-boot.bin\0" \ - "fdtfile=aria/aria.dtb\0" \ - "netdev=eth0\0" \ - "consdev=ttyPSC0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} " \ - "console=${consdev},${baudrate}\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ - "tftp ${fdt_addr_r} ${fdtfile};" \ - "run nfsargs addip addtty;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "net_self=tftp ${kernel_addr_r} ${bootfile};" \ - "tftp ${ramdisk_addr_r} ${ramdiskfile};" \ - "tftp ${fdt_addr_r} ${fdtfile};" \ - "run ramargs addip addtty;" \ - "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0"\ - "load=tftp ${u-boot_addr_r} ${u-boot}\0" \ - "update=protect off ${u-boot_addr} +${filesize};" \ - "era ${u-boot_addr} +${filesize};" \ - "cp.b ${u-boot_addr_r} ${u-boot_addr} ${filesize}\0" \ - "upd=run load update\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_OF_SUPPORT_OLD_DEVICE_TREES 1 - -#define OF_CPU "PowerPC,5121@0" -#define OF_SOC_COMPAT "fsl,mpc5121-immr" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc@80000000/serial@11300" - -/*----------------------------------------------------------------------- - * IDE/ATA stuff - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for IDE not supported */ - -#define CONFIG_IDE_RESET /* reset for IDE supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_BASE_ADDR get_pata_base() - -/* Offset for data I/O RefMan MPC5121EE Table 28-10 */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x00A0) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers RefMan MPC5121EE Table 28-23 */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x00D8) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -#define ATA_BASE_ADDR get_pata_base() - -/* - * Control register bit definitions - */ -#define FSL_ATA_CTRL_FIFO_RST_B 0x80000000 -#define FSL_ATA_CTRL_ATA_RST_B 0x40000000 -#define FSL_ATA_CTRL_FIFO_TX_EN 0x20000000 -#define FSL_ATA_CTRL_FIFO_RCV_EN 0x10000000 -#define FSL_ATA_CTRL_DMA_PENDING 0x08000000 -#define FSL_ATA_CTRL_DMA_ULTRA 0x04000000 -#define FSL_ATA_CTRL_DMA_WRITE 0x02000000 -#define FSL_ATA_CTRL_IORDY_EN 0x01000000 - -/* Clocks in use */ -#define SCCR1_CLOCKS_EN (CLOCK_SCCR1_CFG_EN | \ - CLOCK_SCCR1_LPC_EN | \ - CLOCK_SCCR1_PSC_EN(CONFIG_PSC_CONSOLE) | \ - CLOCK_SCCR1_PSCFIFO_EN | \ - CLOCK_SCCR1_DDR_EN | \ - CLOCK_SCCR1_FEC_EN | \ - CLOCK_SCCR1_NFC_EN | \ - CLOCK_SCCR1_PATA_EN | \ - CLOCK_SCCR1_PCI_EN | \ - CLOCK_SCCR1_TPR_EN) - -#define SCCR2_CLOCKS_EN (CLOCK_SCCR2_MEM_EN | \ - CLOCK_SCCR2_SPDIF_EN | \ - CLOCK_SCCR2_DIU_EN | \ - CLOCK_SCCR2_I2C_EN) - -#endif /* __CONFIG_H */ |