diff options
Diffstat (limited to 'include/configs/cm-bf548.h')
| -rw-r--r-- | include/configs/cm-bf548.h | 131 |
1 files changed, 0 insertions, 131 deletions
diff --git a/include/configs/cm-bf548.h b/include/configs/cm-bf548.h deleted file mode 100644 index 10e8efde5d..0000000000 --- a/include/configs/cm-bf548.h +++ /dev/null @@ -1,131 +0,0 @@ -/* - * U-Boot - Configuration file for cm-bf548 board - */ - -#ifndef __CONFIG_CM_BF548_H__ -#define __CONFIG_CM_BF548_H__ - -#include <asm/config-pre.h> - -/* - * Processor Settings - */ -#define CONFIG_BFIN_CPU bf548-0.0 -#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA - -/* - * Clock Settings - * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV - * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV - */ -/* CONFIG_CLKIN_HZ is any value in Hz */ -#define CONFIG_CLKIN_HZ 25000000 -/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ -/* 1 = CLKIN / 2 */ -#define CONFIG_CLKIN_HALF 0 -/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ -/* 1 = bypass PLL */ -#define CONFIG_PLL_BYPASS 0 -/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ -/* Values can range from 0-63 (where 0 means 64) */ -#define CONFIG_VCO_MULT 21 -/* CCLK_DIV controls the core clock divider */ -/* Values can be 1, 2, 4, or 8 ONLY */ -#define CONFIG_CCLK_DIV 1 -/* SCLK_DIV controls the system clock divider */ -/* Values can range from 1-15 */ -#define CONFIG_SCLK_DIV 4 - -/* Decrease core voltage */ -#define CONFIG_VR_CTL_VAL (VLEV_115 | GAIN_20 | FREQ_1000) - -/* - * Memory Settings - */ -#define CONFIG_MEM_ADD_WDTH 10 -#define CONFIG_MEM_SIZE 64 - -#define CONFIG_EBIU_DDRCTL0_VAL 0x218A83FE -#define CONFIG_EBIU_DDRCTL1_VAL 0x20022222 -#define CONFIG_EBIU_DDRCTL2_VAL 0x00000021 - -/* Default bank mapping: - * Async Bank 0 - 32MB Burst Flash - * Async Bank 1 - Ethernet - * Async Bank 2 - Nothing - * Async Bank 3 - Nothing - */ -#define CONFIG_EBIU_AMGCTL_VAL 0xFF -#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 -#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 -#define CONFIG_EBIU_FCTL_VAL (BCLK_4) -#define CONFIG_EBIU_MODE_VAL (B0MODE_FLASH) - -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) -#define CONFIG_SYS_MALLOC_LEN (640 * 1024) - -/* - * Network Settings - */ -#define ADI_CMDS_NETWORK 1 -#define CONFIG_SMC911X 1 -#define CONFIG_SMC911X_BASE 0x24000000 -#define CONFIG_SMC911X_16_BIT -#define CONFIG_HOSTNAME cm-bf548 - -/* - * Flash Settings - */ -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_BASE 0x20000000 -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 259 - -/* - * Env Storage Settings - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0x20008000 -#define CONFIG_ENV_OFFSET 0x8000 -#define CONFIG_ENV_SIZE 0x8000 -#define CONFIG_ENV_IS_EMBEDDED_IN_LDR - -/* - * I2C Settings - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_ADI - -/* - * Misc Settings - */ -#define CONFIG_RTC_BFIN -#define CONFIG_UART_CONSOLE 1 -#define CONFIG_BOOTCOMMAND "run flashboot" -#define FLASHBOOT_ENV_SETTINGS "flashboot=bootm 0x20040000\0" - -#define CONFIG_ADI_GPIO2 - -#ifndef __ADSPBF542__ -/* Don't waste time transferring a logo over the UART */ -# if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART) -# define EASYLOGO_HEADER <asm/bfin_logo_230x230_gzip.h> -# endif -# define CONFIG_DEB_DMA_URGENT -#endif - -/* Define if want to do post memory test */ -#undef CONFIG_POST -#ifdef CONFIG_POST -#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */ -#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */ -#endif - -/* - * Pull in common ADI header for remaining command/environment setup - */ -#include <configs/bfin_adi_common.h> - -#endif |