diff options
Diffstat (limited to 'include/configs/linkstation.h')
| -rw-r--r-- | include/configs/linkstation.h | 504 |
1 files changed, 0 insertions, 504 deletions
diff --git a/include/configs/linkstation.h b/include/configs/linkstation.h deleted file mode 100644 index fcd809dfbf..0000000000 --- a/include/configs/linkstation.h +++ /dev/null @@ -1,504 +0,0 @@ -/* - * Copyright (C) 2006 Mihai Georgian <u-boot@linuxnotincluded.org.uk> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * Valid values for CONFIG_SYS_TEXT_BASE are: - * - * Standard configuration - all models - * 0xFFF00000 boot from flash - * - * Test configuration (boot from RAM using uloader.o) - * LinkStation HD-HLAN and KuroBox Standard - * 0x03F00000 boot from RAM - * LinkStation HD-HGLAN and KuroBox HG - * 0x07F00000 boot from RAM - */ -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#endif - -#if 0 -#define DEBUG -#endif - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ - -/*----------------------------------------------------------------------- - * User configurable settings: - * Mandatory settings: - * CONFIG_IPADDR_LS - the IP address of the LinkStation - * CONFIG_SERVERIP_LS - the address of the server for NFS/TFTP/DHCP/BOOTP - * Optional settins: - * CONFIG_NCIP_LS - the adress of the computer running net console - * if not configured, it will be set to - * CONFIG_SERVERIP_LS - */ - - -#define CONFIG_IPADDR_LS 192.168.11.150 -#define CONFIG_SERVERIP_LS 192.168.11.149 - -#if !defined(CONFIG_IPADDR_LS) || !defined(CONFIG_SERVERIP_LS) -#error Both CONFIG_IPADDR_LS and CONFIG_SERVERIP_LS must be defined -#endif - -#if !defined(CONFIG_NCIP_LS) -#define CONFIG_NCIP_LS CONFIG_SERVERIP_LS -#endif - -/*---------------------------------------------------------------------- - * DO NOT CHANGE ANYTHING BELOW, UNLESS YOU KNOW WHAT YOU ARE DOING - *---------------------------------------------------------------------*/ - -#define CONFIG_MPC8245 1 -#define CONFIG_LINKSTATION 1 - -/*--------------------------------------- - * Supported models - * - * LinkStation HDLAN /KuroBox Standard (CONFIG_HLAN) - * LinkStation old model (CONFIG_LAN) - totally untested - * LinkStation HGLAN / KuroBox HG (CONFIG_HGLAN) - * - * Models not supported yet - * TeraStatin (CONFIG_HTGL) - */ - -#if defined(CONFIG_HLAN) || defined(CONFIG_LAN) -#define CONFIG_IDENT_STRING " LinkStation / KuroBox" -#elif defined(CONFIG_HGLAN) -#define CONFIG_IDENT_STRING " LinkStation HG / KuroBox HG" -#elif defined(CONFIG_HTGL) -#define CONFIG_IDENT_STRING " TeraStation" -#else -#error No LinkStation model defined -#endif - -#define CONFIG_BOOTDELAY 5 -#define CONFIG_ZERO_BOOTDELAY_CHECK -#undef CONFIG_BOOT_RETRY_TIME - -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT \ - "Boot in %02d seconds ('s' to stop)...", bootdelay -#define CONFIG_AUTOBOOT_STOP_STR "s" - -#define CONFIG_CMD_IDE -#define CONFIG_CMD_PCI -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_PING -#define CONFIG_CMD_EXT2 - -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_NISDOMAIN -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_SEND_HOSTNAME -#define CONFIG_BOOTP_NTPSERVER -#define CONFIG_BOOTP_TIMEOFFSET - -#define CONFIG_OF_LIBFDT 1 - -#define OF_STDOUT_PATH "/soc10x/serial@80004600" - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include <config_cmd_default.h> - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* Default load address: 8 MB */ - -#define CONFIG_BOOTCOMMAND "run bootcmd1" -#define CONFIG_BOOTARGS "root=/dev/sda1 console=ttyS1,57600 netconsole=@192.168.1.7/eth0,@192.168.1.1/00:50:BF:A4:59:71 rtc-rs5c372.probe=0,0x32 debug" -#define CONFIG_NFSBOOTCOMMAND "bootp;run nfsargs;bootm" - -#define CONFIG_SYS_CONSOLE_IS_IN_ENV - -#if defined(CONFIG_HLAN) || defined(CONFIG_LAN) -#define UBFILE "share/u-boot/u-boot-hd.flash.bin" -#elif defined(CONFIG_HGLAN) -#define UBFILE "share/u-boot/u-boot-hg.flash.bin" -#elif defined(CONFIG_HTGL) -#define UBFILE "share/u-boot/u-boot-ht.flash.bin" -#else -#error No LinkStation model defined -#endif - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "autoload=no\0" \ - "stdin=nc\0" \ - "stdout=nc\0" \ - "stderr=nc\0" \ - "ipaddr="__stringify(CONFIG_IPADDR_LS)"\0" \ - "netmask=255.255.255.0\0" \ - "serverip="__stringify(CONFIG_SERVERIP_LS)"\0" \ - "ncip="__stringify(CONFIG_NCIP_LS)"\0" \ - "netretry=no\0" \ - "nc=setenv stdin nc;setenv stdout nc;setenv stderr nc\0" \ - "ser=setenv stdin serial;setenv stdout serial;setenv stderr serial\0" \ - "ldaddr=800000\0" \ - "hdpart=0:1\0" \ - "hdfile=boot/uImage\0" \ - "hdload=echo Loading ${hdpart}:${hdfile};ext2load ide ${hdpart} ${ldaddr} ${hdfile};ext2load ide ${hdpart} 7f0000 boot/kuroboxHG.dtb\0" \ - "boothd=setenv bootargs " CONFIG_BOOTARGS ";bootm ${ldaddr} - 7f0000\0" \ - "hdboot=run hdload;run boothd\0" \ - "flboot=setenv bootargs root=/dev/hda1;bootm ffc00000\0" \ - "emboot=setenv bootargs root=/dev/ram0;bootm ffc00000\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off\0" \ - "bootretry=30\0" \ - "bootcmd1=run hdboot;run flboot\0" \ - "bootcmd2=run flboot\0" \ - "bootcmd3=run emboot\0" \ - "writeng=protect off fff70000 fff7ffff;era fff70000 fff7ffff;mw.l 800000 4e474e47 1;cp.b 800000 fff70000 4\0" \ - "writeok=protect off fff70000 fff7ffff;era fff70000 fff7ffff;mw.l 800000 4f4b4f4b 1;cp.b 800000 fff70000 4\0" \ - "ubpart=0:3\0" \ - "ubfile="UBFILE"\0" \ - "ubload=echo Loading ${ubpart}:${ubfile};ext2load ide ${ubpart} ${ldaddr} ${ubfile}\0" \ - "ubsaddr=fff00000\0" \ - "ubeaddr=fff2ffff\0" \ - "ubflash=protect off ${ubsaddr} ${ubeaddr};era ${ubsaddr} ${ubeaddr};cp.b ${ldaddr} ${ubsaddr} ${filesize};cmp.b ${ldaddr} ${ubsaddr} ${filesize}\0" \ - "upgrade=run ubload ubflash\0" - -/*----------------------------------------------------------------------- - * PCI stuff - */ -#define CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -/* Verified: CONFIG_PCI_PNP doesn't work */ -#undef CONFIG_PCI_PNP -#define CONFIG_PCI_SCAN_SHOW - -#ifndef CONFIG_PCI_PNP -/* Keep the following defines in sync with the BAT mappings */ - -#define PCI_ETH_IOADDR 0xbfff00 -#define PCI_ETH_MEMADDR 0xbffffc00 -#define PCI_IDE_IOADDR 0xbffed0 -#define PCI_IDE_MEMADDR 0xbffffb00 -#define PCI_USB0_IOADDR 0 -#define PCI_USB0_MEMADDR 0xbfffe000 -#define PCI_USB1_IOADDR 0 -#define PCI_USB1_MEMADDR 0xbfffd000 -#define PCI_USB2_IOADDR 0 -#define PCI_USB2_MEMADDR 0xbfffcf00 - -#endif - -/*----------------------------------------------------------------------- - * Ethernet stuff - */ - -#if defined(CONFIG_LAN) || defined(CONFIG_HLAN) -#define CONFIG_TULIP -#define CONFIG_TULIP_USE_IO -#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL) -#define CONFIG_RTL8169 -#endif - -#define CONFIG_NET_RETRY_COUNT 5 - -#define CONFIG_NETCONSOLE - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_SYS_FLASH_BASE 0xFFC00000 -#define CONFIG_SYS_FLASH_SIZE 0x00400000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - -#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 -#define CONFIG_SYS_EUMB_ADDR 0x80000000 -#define CONFIG_SYS_PCI_MEM_ADDR 0xB0000000 -#define CONFIG_SYS_MISC_REGION_ADDR 0xFE000000 - -#define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256 kB */ -#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve some kB for malloc() */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 1M ... 8M in DRAM */ - -/* Maximum amount of RAM */ -#if defined(CONFIG_HLAN) || defined(CONFIG_LAN) -#define CONFIG_SYS_MAX_RAM_SIZE 0x04000000 /* 64MB of SDRAM */ -#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL) -#define CONFIG_SYS_MAX_RAM_SIZE 0x08000000 /* 128MB of SDRAM */ -#else -#error Unknown LinkStation type -#endif - -/*----------------------------------------------------------------------- - * Change CONFIG_SYS_TEXT_BASE in bord/linkstation/config.mk to get a RAM build - * - * RAM based builds are for testing purposes. A Linux module, uloader.o, - * exists to load U-Boot and pass control to it - * - * Always do "make clean" after changing the build type - */ -#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_RAMBOOT -#endif - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area - */ -#if 1 /* RAM is available when the first C function is called */ -#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_MAX_RAM_SIZE - 0x1000) -#else -#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 -#endif -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/*---------------------------------------------------------------------- - * Serial configuration - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 57600 - -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL - -#define CONFIG_SYS_NS16550_REG_SIZE 1 - -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4600) /* Console port */ -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4500) /* AVR port */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - * For the detail description refer to the MPC8245 user's manual. - * - * Unless indicated otherwise, the values are - * taken from the orignal Linkstation boot code - * - * Most of the low level configuration setttings are normally used - * in arch/powerpc/cpu/mpc824x/cpu_init.c which is NOT used by this implementation. - * Low level initialisation is done in board/linkstation/early_init.S - * The values below are included for reference purpose only - */ - -/* FIXME: 32.768 MHz is the crystal frequency but */ -/* the real frequency is lower by about 0.75% */ -#define CONFIG_SYS_CLK_FREQ 32768000 - -/* Bit-field values for MCCR1. */ -#define CONFIG_SYS_ROMNAL 0 -#define CONFIG_SYS_ROMFAL 11 - -#define CONFIG_SYS_BANK0_ROW 2 /* Only bank 0 used: 13 x n x 4 */ -#define CONFIG_SYS_BANK1_ROW 0 -#define CONFIG_SYS_BANK2_ROW 0 -#define CONFIG_SYS_BANK3_ROW 0 -#define CONFIG_SYS_BANK4_ROW 0 -#define CONFIG_SYS_BANK5_ROW 0 -#define CONFIG_SYS_BANK6_ROW 0 -#define CONFIG_SYS_BANK7_ROW 0 - -/* Bit-field values for MCCR2. */ -#define CONFIG_SYS_TSWAIT 0 -#if defined(CONFIG_LAN) || defined(CONFIG_HLAN) -#define CONFIG_SYS_REFINT 0x15e0 -#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL) -#define CONFIG_SYS_REFINT 0x1580 -#endif - -/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */ -#define CONFIG_SYS_BSTOPRE 0x91c - -/* Bit-field values for MCCR3. */ -#define CONFIG_SYS_REFREC 7 - -/* Bit-field values for MCCR4. */ -#define CONFIG_SYS_PRETOACT 2 -#define CONFIG_SYS_ACTTOPRE 2 /* Original value was 2 */ -#define CONFIG_SYS_ACTORW 2 -#if defined(CONFIG_LAN) || defined(CONFIG_HLAN) -#define CONFIG_SYS_SDMODE_CAS_LAT 2 /* For 100MHz bus */ -/*#define CONFIG_SYS_SDMODE_BURSTLEN 3*/ -#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL) -#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* For 133MHz bus */ -/*#define CONFIG_SYS_SDMODE_BURSTLEN 2*/ -#endif -#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 -#define CONFIG_SYS_EXTROM 1 /* Original setting but there is no EXTROM */ -#define CONFIG_SYS_REGDIMM 0 -#define CONFIG_SYS_DBUS_SIZE2 1 -#define CONFIG_SYS_SDMODE_WRAP 0 - -#define CONFIG_SYS_PGMAX 0x32 /* All boards use this setting. Original 0x92 */ -#define CONFIG_SYS_SDRAM_DSCD 0x30 - -/* Memory bank settings. - * Only bits 20-29 are actually used from these vales to set the - * start/end addresses. The upper two bits will always be 0, and the lower - * 20 bits will be 0x00000 for a start address, or 0xfffff for an end - * address. Refer to the MPC8240 book. - */ - -#define CONFIG_SYS_BANK0_START 0x00000000 -#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) -#define CONFIG_SYS_BANK0_ENABLE 1 -#define CONFIG_SYS_BANK1_START 0x3ff00000 -#define CONFIG_SYS_BANK1_END 0x3fffffff -#define CONFIG_SYS_BANK1_ENABLE 0 -#define CONFIG_SYS_BANK2_START 0x3ff00000 -#define CONFIG_SYS_BANK2_END 0x3fffffff -#define CONFIG_SYS_BANK2_ENABLE 0 -#define CONFIG_SYS_BANK3_START 0x3ff00000 -#define CONFIG_SYS_BANK3_END 0x3fffffff -#define CONFIG_SYS_BANK3_ENABLE 0 -#define CONFIG_SYS_BANK4_START 0x3ff00000 -#define CONFIG_SYS_BANK4_END 0x3fffffff -#define CONFIG_SYS_BANK4_ENABLE 0 -#define CONFIG_SYS_BANK5_START 0x3ff00000 -#define CONFIG_SYS_BANK5_END 0x3fffffff -#define CONFIG_SYS_BANK5_ENABLE 0 -#define CONFIG_SYS_BANK6_START 0x3ff00000 -#define CONFIG_SYS_BANK6_END 0x3fffffff -#define CONFIG_SYS_BANK6_ENABLE 0 -#define CONFIG_SYS_BANK7_START 0x3ff00000 -#define CONFIG_SYS_BANK7_END 0x3fffffff -#define CONFIG_SYS_BANK7_ENABLE 0 - -#define CONFIG_SYS_ODCR 0x15 - -/*---------------------------------------------------------------------- - * Initial BAT mappings - */ - -/* NOTES: - * 1) GUARDED and WRITETHROUGH not allowed in IBATS - * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT - */ - -/* SDRAM */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -/* EUMB: 1MB of address space */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_EUMB_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_EUMB_ADDR | BATU_BL_1M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_DBAT1L (CONFIG_SYS_IBAT1L | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* PCI Mem: 256MB of address space */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI_MEM_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI_MEM_ADDR | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_DBAT2L (CONFIG_SYS_IBAT2L | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -/* PCI and local ROM/Flash: last 32MB of address space */ -#define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_ADDR | BATU_BL_32M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_DBAT3L (CONFIG_SYS_IBAT3L | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - * - * FIXME: This doesn't appear to be true for the newer kernels - * which map more that 8 MB - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ - -#undef CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 72 /* Max number of sectors per flash */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 12000 -#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ - -#define CONFIG_ENV_IS_IN_FLASH -/* - * The original LinkStation flash organisation uses - * 448 kB (0xFFF00000 - 0xFFF6FFFF) for the boot loader - * We use the last sector of this area to store the environment - * which leaves max. 384 kB for the U-Boot itself - */ -#define CONFIG_ENV_ADDR 0xFFF60000 -#define CONFIG_ENV_SIZE 0x00010000 -#define CONFIG_ENV_SECT_SIZE 0x00010000 - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 -#ifdef CONFIG_CMD_KGDB -#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * IDE/ATA definitions - */ -#undef CONFIG_IDE_LED /* No IDE LED */ -#define CONFIG_IDE_RESET /* no reset for ide supported */ -#define CONFIG_IDE_PREINIT /* check for units */ -#define CONFIG_LBA48 /* 48 bit LBA supported */ - -#if defined(CONFIG_LAN) || defined(CONFIG_HLAN) || defined(CONFIG_HGLAN) -#define CONFIG_SYS_IDE_MAXBUS 1 /* Scan only 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* Only 1 drive per IDE bus */ -#elif defined(CONFIG_HGTL) -#define CONFIG_SYS_IDE_MAXBUS 2 /* Max. 2 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ -#else -#error Config IDE: Unknown LinkStation type -#endif - -#define CONFIG_SYS_ATA_BASE_ADDR 0 - -#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0 /* Offset for normal registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0 /* Offset for alternate registers */ - -/*----------------------------------------------------------------------- - * Partitions and file system - */ -#define CONFIG_DOS_PARTITION - -#endif /* __CONFIG_H */ |