diff options
Diffstat (limited to 'include/configs/sbc8240.h')
| -rw-r--r-- | include/configs/sbc8240.h | 364 |
1 files changed, 0 insertions, 364 deletions
diff --git a/include/configs/sbc8240.h b/include/configs/sbc8240.h deleted file mode 100644 index 2267677d2e..0000000000 --- a/include/configs/sbc8240.h +++ /dev/null @@ -1,364 +0,0 @@ -/* - * (C) Copyright 2001 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -/* - * Configuration settings for the sbc8240 board. - */ - -/* ------------------------------------------------------------------------- */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC824X 1 -#define CONFIG_MPC8240 1 -#define CONFIG_WRSBC8240 1 - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 9600 -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -#define CONFIG_PREBOOT "echo;echo Welcome to U-Boot for the sbc8240;echo;echo Type \"? or help\" to get on-line help;echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_BOOTCOMMAND "version;echo;tftpboot $loadaddr $loadfile;bootvx" /* autoboot command */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "bootargs=$fei(0,0)host:/T221ppc/target/config/sbc8240/vxWorks.st " \ - "e=192.168.193.102 h=192.168.193.99 u=target pw=hello f=0x08 " \ - "tn=sbc8240 o=fei \0" \ - "env_startaddr=FFF70000\0" \ - "env_endaddr=FFF7FFFF\0" \ - "loadfile=vxWorks.st\0" \ - "loadaddr=0x01000000\0" \ - "net_load=tftpboot $loadaddr $loadfile\0" \ - "uboot_startaddr=FFF00000\0" \ - "uboot_endaddr=FFF3FFFF\0" \ - "update=tftp $loadaddr /u-boot.bin;" \ - "protect off $uboot_startaddr $uboot_endaddr;" \ - "era $uboot_startaddr $uboot_endaddr;" \ - "cp.b $loadaddr $uboot_startaddr $filesize;" \ - "protect on $uboot_startaddr $uboot_endaddr\0" \ - "zapenv=protect off $env_startaddr $env_endaddr;" \ - "era $env_startaddr $env_endaddr;" \ - "protect on $env_startaddr $env_endaddr\0" - -#define CONFIG_BOOTDELAY 5 - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE - - -#define CONFIG_ENV_OVERWRITE - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_BSP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_SDRAM - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ - -#if 1 -#define CONFIG_SYS_HUSH_PARSER 1 /* use "hush" command parser */ -#endif -#ifdef CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#endif - -#define CONFIG_ETHADDR DE:AD:BE:EF:01:01 /* Ethernet address */ -#define CONFIG_IPADDR 192.168.193.102 -#define CONFIG_NETMASK 255.255.255.248 -#define CONFIG_SERVERIP 192.168.193.99 - -#define CONFIG_STATUS_LED /* Status LED enabled */ -#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ - -#define STATUS_LED_BIT 0x00000001 -#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -#define STATUS_LED_STATE STATUS_LED_BLINKING -#define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ -#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ - -#ifndef __ASSEMBLY__ -/* LEDs */ -typedef unsigned int led_id_t; - -#define __led_toggle(_msk) \ - do { \ - *((volatile char *) (CONFIG_SYS_LED_BASE)) ^= (_msk); \ - } while(0) - -#define __led_set(_msk, _st) \ - do { \ - if ((_st)) \ - *((volatile char *) (CONFIG_SYS_LED_BASE)) |= (_msk); \ - else \ - *((volatile char *) (CONFIG_SYS_LED_BASE)) &= ~(_msk); \ - } while(0) - -#define __led_init(msk, st) __led_set(msk, st) - -#endif - -#define CONFIG_MISC_INIT_R -#define CONFIG_SYS_LED_BASE 0xFFE80000 - -/* Print Buffer Size - */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */ - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFF00000 - -#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 - -#define CONFIG_SYS_EUMB_ADDR 0xFCE00000 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ - - /* Maximum amount of RAM. - */ -#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000 - -#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE -#undef CONFIG_SYS_RAMBOOT -#else -#define CONFIG_SYS_RAMBOOT -#endif - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area - */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL - -#define CONFIG_SYS_NS16550_REG_SIZE 1 - -#define CONFIG_SYS_NS16550_CLK 3686400 - -#define CONFIG_SYS_NS16550_COM1 0xFFF80000 - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - * For the detail description refer to the MPC8240 user's manual. - */ - -#define CONFIG_SYS_CLK_FREQ 33000000 -#define CONFIG_SYS_HZ 1000 -#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3 - - /* Bit-field values for MCCR1. - */ -#define CONFIG_SYS_ROMNAL 0 -#define CONFIG_SYS_ROMFAL 7 - - /* Bit-field values for MCCR2. - */ -#define CONFIG_SYS_REFINT 430 /* Refresh interval */ - - /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. - */ -#define CONFIG_SYS_BSTOPRE 192 - - /* Bit-field values for MCCR3. - */ -#define CONFIG_SYS_REFREC 2 /* Refresh to activate interval */ -#define CONFIG_SYS_RDLAT 3 /* Data latancy from read command */ - - /* Bit-field values for MCCR4. - */ -#define CONFIG_SYS_PRETOACT 2 /* Precharge to activate interval */ -#define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */ -#define CONFIG_SYS_SDMODE_CAS_LAT 2 /* SDMODE CAS latancy */ -#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */ -#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length */ -#define CONFIG_SYS_ACTORW 2 -#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1 - -/* Memory bank settings. - * Only bits 20-29 are actually used from these vales to set the - * start/end addresses. The upper two bits will always be 0, and the lower - * 20 bits will be 0x00000 for a start address, or 0xfffff for an end - * address. Refer to the MPC8240 book. - */ - -#define CONFIG_SYS_BANK0_START 0x00000000 -#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1) -#define CONFIG_SYS_BANK0_ENABLE 1 -#define CONFIG_SYS_BANK1_START 0x3ff00000 -#define CONFIG_SYS_BANK1_END 0x3fffffff -#define CONFIG_SYS_BANK1_ENABLE 0 -#define CONFIG_SYS_BANK2_START 0x3ff00000 -#define CONFIG_SYS_BANK2_END 0x3fffffff -#define CONFIG_SYS_BANK2_ENABLE 0 -#define CONFIG_SYS_BANK3_START 0x3ff00000 -#define CONFIG_SYS_BANK3_END 0x3fffffff -#define CONFIG_SYS_BANK3_ENABLE 0 -#define CONFIG_SYS_BANK4_START 0x3ff00000 -#define CONFIG_SYS_BANK4_END 0x3fffffff -#define CONFIG_SYS_BANK4_ENABLE 0 -#define CONFIG_SYS_BANK5_START 0x3ff00000 -#define CONFIG_SYS_BANK5_END 0x3fffffff -#define CONFIG_SYS_BANK5_ENABLE 0 -#define CONFIG_SYS_BANK6_START 0x3ff00000 -#define CONFIG_SYS_BANK6_END 0x3fffffff -#define CONFIG_SYS_BANK6_ENABLE 0 -#define CONFIG_SYS_BANK7_START 0x3ff00000 -#define CONFIG_SYS_BANK7_END 0x3fffffff -#define CONFIG_SYS_BANK7_ENABLE 0 - -#define CONFIG_SYS_ODCR 0xff - -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_IBAT3L (0xFC000000 | BATL_PP_10 | BATL_CACHEINHIBIT) -#define CONFIG_SYS_IBAT3U (0xFC000000 | BATU_BL_64M | BATU_VS | BATU_VP) - -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* Max number of sectors in one bank */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ - - /* Warining: environment is not EMBEDDED in the U-Boot code. - * It's stored in flash separately. - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0xFFF70000 -#define CONFIG_ENV_SIZE 0x4000 /* Size of the Environment */ -#define CONFIG_ENV_OFFSET 0 /* starting right at the beginning */ -#define CONFIG_ENV_SECT_SIZE 0x40000 /* Size of the Environment Sector */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 32 -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * PCI stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_PNP /* we need Plug 'n Play */ -#define CONFIG_NET_MULTI /* Multi ethernet cards support */ -#define CONFIG_TULIP -#define CONFIG_EEPRO100 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#endif /* __CONFIG_H */ |