diff options
Diffstat (limited to 'include/configs/ti_armv7_keystone2.h')
| -rw-r--r-- | include/configs/ti_armv7_keystone2.h | 295 |
1 files changed, 295 insertions, 0 deletions
diff --git a/include/configs/ti_armv7_keystone2.h b/include/configs/ti_armv7_keystone2.h new file mode 100644 index 0000000000..2b6a2297e6 --- /dev/null +++ b/include/configs/ti_armv7_keystone2.h @@ -0,0 +1,295 @@ +/* + * Common configuration header file for all Keystone II EVM platforms + * + * (C) Copyright 2012-2014 + * Texas Instruments Incorporated, <www.ti.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_KS2_EVM_H +#define __CONFIG_KS2_EVM_H + +#define CONFIG_SOC_KEYSTONE + +/* U-Boot Build Configuration */ +#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 2nd stage loader */ +#define CONFIG_BOARD_EARLY_INIT_F + +/* SoC Configuration */ +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_SYS_ARCH_TIMER +#define CONFIG_SYS_TEXT_BASE 0x0c001000 +#define CONFIG_SPL_TARGET "u-boot-spi.gph" +#define CONFIG_SYS_DCACHE_OFF + +/* Memory Configuration */ +#define CONFIG_NR_DRAM_BANKS 2 +#define CONFIG_SYS_LPAE_SDRAM_BASE 0x800000000 +#define CONFIG_MAX_RAM_BANK_SIZE (2 << 30) /* 2GB */ +#define CONFIG_STACKSIZE (512 << 10) /* 512 KiB */ +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_TEXT_BASE - \ + GENERATED_GBL_DATA_SIZE) + +/* SPL SPI Loader Configuration */ +#define CONFIG_SPL_PAD_TO 65536 +#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_PAD_TO - 8) +#define CONFIG_SPL_BSS_START_ADDR (CONFIG_SPL_TEXT_BASE + \ + CONFIG_SPL_MAX_SIZE) +#define CONFIG_SPL_BSS_MAX_SIZE (32 * 1024) +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ + CONFIG_SPL_BSS_MAX_SIZE) +#define CONFIG_SYS_SPL_MALLOC_SIZE (32 * 1024) +#define CONFIG_SPL_STACK_SIZE (8 * 1024) +#define CONFIG_SPL_STACK (CONFIG_SYS_SPL_MALLOC_START + \ + CONFIG_SYS_SPL_MALLOC_SIZE + \ + CONFIG_SPL_STACK_SIZE - 4) +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_SPL_PAD_TO + +/* UART Configuration */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_MEM32 +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550_COM1 KS2_UART0_BASE +#define CONFIG_SYS_NS16550_COM2 KS2_UART1_BASE +#define CONFIG_SYS_NS16550_CLK clk_get_rate(KS2_CLK1_6) +#define CONFIG_CONS_INDEX 1 + +/* SPI Configuration */ +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_DAVINCI_SPI +#define CONFIG_SYS_SPI_CLK clk_get_rate(KS2_CLK1_6) +#define CONFIG_SF_DEFAULT_SPEED 30000000 +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#define CONFIG_SYS_SPI0 +#define CONFIG_SYS_SPI_BASE KS2_SPI0_BASE +#define CONFIG_SYS_SPI0_NUM_CS 4 +#define CONFIG_SYS_SPI1 +#define CONFIG_SYS_SPI1_BASE KS2_SPI1_BASE +#define CONFIG_SYS_SPI1_NUM_CS 4 +#define CONFIG_SYS_SPI2 +#define CONFIG_SYS_SPI2_BASE KS2_SPI2_BASE +#define CONFIG_SYS_SPI2_NUM_CS 4 + +/* Network Configuration */ +#define CONFIG_PHYLIB +#define CONFIG_PHY_MARVELL +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 32 +#define CONFIG_SYS_SGMII_REFCLK_MHZ 312 +#define CONFIG_SYS_SGMII_LINERATE_MHZ 1250 +#define CONFIG_SYS_SGMII_RATESCALE 2 + +/* Keyston Navigator Configuration */ +#define CONFIG_TI_KSNAV +#define CONFIG_KSNAV_QM_BASE_ADDRESS KS2_QM_BASE_ADDRESS +#define CONFIG_KSNAV_QM_CONF_BASE KS2_QM_CONF_BASE +#define CONFIG_KSNAV_QM_DESC_SETUP_BASE KS2_QM_DESC_SETUP_BASE +#define CONFIG_KSNAV_QM_STATUS_RAM_BASE KS2_QM_STATUS_RAM_BASE +#define CONFIG_KSNAV_QM_INTD_CONF_BASE KS2_QM_INTD_CONF_BASE +#define CONFIG_KSNAV_QM_PDSP1_CMD_BASE KS2_QM_PDSP1_CMD_BASE +#define CONFIG_KSNAV_QM_PDSP1_CTRL_BASE KS2_QM_PDSP1_CTRL_BASE +#define CONFIG_KSNAV_QM_PDSP1_IRAM_BASE KS2_QM_PDSP1_IRAM_BASE +#define CONFIG_KSNAV_QM_MANAGER_QUEUES_BASE KS2_QM_MANAGER_QUEUES_BASE +#define CONFIG_KSNAV_QM_MANAGER_Q_PROXY_BASE KS2_QM_MANAGER_Q_PROXY_BASE +#define CONFIG_KSNAV_QM_QUEUE_STATUS_BASE KS2_QM_QUEUE_STATUS_BASE +#define CONFIG_KSNAV_QM_LINK_RAM_BASE KS2_QM_LINK_RAM_BASE +#define CONFIG_KSNAV_QM_REGION_NUM KS2_QM_REGION_NUM +#define CONFIG_KSNAV_QM_QPOOL_NUM KS2_QM_QPOOL_NUM + +/* NETCP pktdma */ +#define CONFIG_KSNAV_PKTDMA_NETCP +#define CONFIG_KSNAV_NETCP_PDMA_CTRL_BASE KS2_NETCP_PDMA_CTRL_BASE +#define CONFIG_KSNAV_NETCP_PDMA_TX_BASE KS2_NETCP_PDMA_TX_BASE +#define CONFIG_KSNAV_NETCP_PDMA_TX_CH_NUM KS2_NETCP_PDMA_TX_CH_NUM +#define CONFIG_KSNAV_NETCP_PDMA_RX_BASE KS2_NETCP_PDMA_RX_BASE +#define CONFIG_KSNAV_NETCP_PDMA_RX_CH_NUM KS2_NETCP_PDMA_RX_CH_NUM +#define CONFIG_KSNAV_NETCP_PDMA_SCHED_BASE KS2_NETCP_PDMA_SCHED_BASE +#define CONFIG_KSNAV_NETCP_PDMA_RX_FLOW_BASE KS2_NETCP_PDMA_RX_FLOW_BASE +#define CONFIG_KSNAV_NETCP_PDMA_RX_FLOW_NUM KS2_NETCP_PDMA_RX_FLOW_NUM +#define CONFIG_KSNAV_NETCP_PDMA_RX_FREE_QUEUE KS2_NETCP_PDMA_RX_FREE_QUEUE +#define CONFIG_KSNAV_NETCP_PDMA_RX_RCV_QUEUE KS2_NETCP_PDMA_RX_RCV_QUEUE +#define CONFIG_KSNAV_NETCP_PDMA_TX_SND_QUEUE KS2_NETCP_PDMA_TX_SND_QUEUE + +/* Keystone net */ +#define CONFIG_DRIVER_TI_KEYSTONE_NET +#define CONFIG_KSNET_MAC_ID_BASE KS2_MAC_ID_BASE_ADDR +#define CONFIG_KSNET_NETCP_BASE KS2_NETCP_BASE +#define CONFIG_KSNET_SERDES_SGMII_BASE KS2_SGMII_SERDES_BASE +#define CONFIG_KSNET_SERDES_SGMII2_BASE KS2_SGMII_SERDES2_BASE +#define CONFIG_KSNET_SERDES_LANES_PER_SGMII KS2_LANES_PER_SGMII_SERDES + +/* SerDes */ +#define CONFIG_TI_KEYSTONE_SERDES + +/* AEMIF */ +#define CONFIG_TI_AEMIF +#define CONFIG_AEMIF_CNTRL_BASE KS2_AEMIF_CNTRL_BASE + +/* I2C Configuration */ +#define CONFIG_SYS_I2C_DAVINCI +#define CONFIG_SYS_DAVINCI_I2C_SPEED 100000 +#define CONFIG_SYS_DAVINCI_I2C_SLAVE 0x10 /* SMBus host address */ +#define CONFIG_SYS_DAVINCI_I2C_SPEED1 100000 +#define CONFIG_SYS_DAVINCI_I2C_SLAVE1 0x10 /* SMBus host address */ +#define CONFIG_SYS_DAVINCI_I2C_SPEED2 100000 +#define CONFIG_SYS_DAVINCI_I2C_SLAVE2 0x10 /* SMBus host address */ +#define I2C_BUS_MAX 3 + +/* EEPROM definitions */ +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 +#define CONFIG_ENV_EEPROM_IS_ON_I2C + +/* NAND Configuration */ +#define CONFIG_NAND_DAVINCI +#define CONFIG_KEYSTONE_RBL_NAND +#define CONFIG_KEYSTONE_NAND_MAX_RBL_SIZE CONFIG_ENV_OFFSET +#define CONFIG_SYS_NAND_MASK_CLE 0x4000 +#define CONFIG_SYS_NAND_MASK_ALE 0x2000 +#define CONFIG_SYS_NAND_CS 2 +#define CONFIG_SYS_NAND_USE_FLASH_BBT +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST + +#define CONFIG_SYS_NAND_LARGEPAGE +#define CONFIG_SYS_NAND_BASE_LIST { 0x30000000, } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_MAX_CHIPS 1 +#define CONFIG_SYS_NAND_NO_SUBPAGE_WRITE +#define CONFIG_ENV_SIZE (256 << 10) /* 256 KiB */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x100000 +#define CONFIG_MTD_PARTITIONS +#define CONFIG_RBTREE +#define CONFIG_LZO +#define MTDIDS_DEFAULT "nand0=davinci_nand.0" +#define MTDPARTS_DEFAULT "mtdparts=davinci_nand.0:" \ + "1024k(bootloader)ro,512k(params)ro," \ + "-(ubifs)" + +/* USB Configuration */ +#define CONFIG_USB_XHCI +#define CONFIG_USB_XHCI_DWC3 +#define CONFIG_USB_XHCI_KEYSTONE +#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 +#define CONFIG_EFI_PARTITION +#define CONFIG_FS_FAT +#define CONFIG_SYS_CACHELINE_SIZE 64 +#define CONFIG_USB_SS_BASE KS2_USB_SS_BASE +#define CONFIG_USB_HOST_XHCI_BASE KS2_USB_HOST_XHCI_BASE +#define CONFIG_DEV_USB_PHY_BASE KS2_DEV_USB_PHY_BASE +#define CONFIG_USB_PHY_CFG_BASE KS2_USB_PHY_CFG_BASE + +/* U-Boot command configuration */ +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_NAND +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#define CONFIG_CMD_SF +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_USB + +/* U-Boot general configuration */ +#define CONFIG_MISC_INIT_R +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC +#define CONFIG_TIMESTAMP + +/* EDMA3 */ +#define CONFIG_TI_EDMA3 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + DEFAULT_LINUX_BOOT_ENV \ + CONFIG_EXTRA_ENV_KS2_BOARD_SETTINGS \ + "boot=ubi\0" \ + "tftp_root=/\0" \ + "nfs_root=/export\0" \ + "mem_lpae=1\0" \ + "mem_reserve=512M\0" \ + "addr_ubi=0x82000000\0" \ + "addr_secdb_key=0xc000000\0" \ + "name_kern=zImage\0" \ + "run_mon=mon_install ${addr_mon}\0" \ + "run_kern=bootz ${loadaddr} - ${fdtaddr}\0" \ + "init_net=run args_all args_net\0" \ + "init_ubi=run args_all args_ubi; " \ + "ubi part ubifs; ubifsmount ubi:boot;" \ + "ubifsload ${addr_secdb_key} securedb.key.bin;\0" \ + "get_fdt_net=dhcp ${fdtaddr} ${tftp_root}/${name_fdt}\0" \ + "get_fdt_ubi=ubifsload ${fdtaddr} ${name_fdt}\0" \ + "get_kern_net=dhcp ${loadaddr} ${tftp_root}/${name_kern}\0" \ + "get_kern_ubi=ubifsload ${loadaddr} ${name_kern}\0" \ + "get_mon_net=dhcp ${addr_mon} ${tftp_root}/${name_mon}\0" \ + "get_mon_ubi=ubifsload ${addr_mon} ${name_mon}\0" \ + "get_uboot_net=dhcp ${addr_uboot} ${tftp_root}/${name_uboot}\0" \ + "burn_uboot_spi=sf probe; sf erase 0 0x100000; " \ + "sf write ${addr_uboot} 0 ${filesize}\0" \ + "burn_uboot_nand=nand erase 0 0x100000; " \ + "nand write ${addr_uboot} 0 ${filesize}\0" \ + "args_all=setenv bootargs console=ttyS0,115200n8 rootwait=1\0" \ + "args_net=setenv bootargs ${bootargs} rootfstype=nfs " \ + "root=/dev/nfs rw nfsroot=${serverip}:${nfs_root}," \ + "${nfs_options} ip=dhcp\0" \ + "nfs_options=v3,tcp,rsize=4096,wsize=4096\0" \ + "get_fdt_ramfs=dhcp ${fdtaddr} ${tftp_root}/${name_fdt}\0" \ + "get_kern_ramfs=dhcp ${loadaddr} ${tftp_root}/${name_kern}\0" \ + "get_mon_ramfs=dhcp ${addr_mon} ${tftp_root}/${name_mon}\0" \ + "get_fs_ramfs=dhcp ${rdaddr} ${tftp_root}/${name_fs}\0" \ + "get_ubi_net=dhcp ${addr_ubi} ${tftp_root}/${name_ubi}\0" \ + "burn_ubi=nand erase.part ubifs; " \ + "nand write ${addr_ubi} ubifs ${filesize}\0" \ + "init_ramfs=run args_all args_ramfs get_fs_ramfs\0" \ + "args_ramfs=setenv bootargs ${bootargs} " \ + "rdinit=/sbin/init rw root=/dev/ram0 " \ + "initrd=0x802000000,9M\0" \ + "no_post=1\0" \ + "mtdparts=mtdparts=davinci_nand.0:" \ + "1024k(bootloader)ro,512k(params)ro,-(ubifs)\0" + +#define CONFIG_BOOTCOMMAND \ + "run init_${boot} get_fdt_${boot} get_mon_${boot} " \ + "get_kern_${boot} run_mon run_kern" + +#define CONFIG_BOOTARGS \ + +/* Linux interfacing */ +#define CONFIG_OF_BOARD_SETUP + +/* Now for the remaining common defines */ +#include <configs/ti_armv7_common.h> + +/* We wont be loading up OS from SPL for now.. */ +#undef CONFIG_SPL_OS_BOOT + +/* We do not have MMC support.. yet.. */ +#undef CONFIG_SPL_LIBDISK_SUPPORT +#undef CONFIG_SPL_MMC_SUPPORT +#undef CONFIG_SPL_FAT_SUPPORT +#undef CONFIG_SPL_EXT_SUPPORT +#undef CONFIG_MMC +#undef CONFIG_GENERIC_MMC +#undef CONFIG_CMD_MMC + +/* And no support for GPIO, yet.. */ +#undef CONFIG_SPL_GPIO_SUPPORT +#undef CONFIG_CMD_GPIO + +/* we may include files below only after all above definitions */ +#include <asm/arch/hardware.h> +#include <asm/arch/clock.h> +#define CONFIG_SYS_HZ_CLOCK clk_get_rate(KS2_CLK1_6) + +#endif /* __CONFIG_KS2_EVM_H */ |