diff options
Diffstat (limited to 'include/configs/walnut.h')
| -rw-r--r-- | include/configs/walnut.h | 155 |
1 files changed, 15 insertions, 140 deletions
diff --git a/include/configs/walnut.h b/include/configs/walnut.h index adc420b9ad..e19c5f3482 100644 --- a/include/configs/walnut.h +++ b/include/configs/walnut.h @@ -38,122 +38,44 @@ #define CONFIG_WALNUT 1 /* ...on a WALNUT board */ /* ...and on a SYCAMORE board */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME walnut +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=walnut\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/walnut/uImage\0" \ +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff80000\0" \ "ramdisk_addr=fff80000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/walnut/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run net_nfs" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ - -#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - #define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - #define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. * If CFG_405_UART_ERRATA_59, then UART divisor is 31. * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. @@ -167,29 +89,11 @@ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -224,13 +128,8 @@ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFFF80000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) /* * Define here the location of the environment variables (FLASH or NVRAM). @@ -243,13 +142,6 @@ #define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ #endif -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * FLASH organization */ @@ -335,21 +227,4 @@ */ #define SPD_EEPROM_ADDRESS 0x50 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ |