diff options
Diffstat (limited to 'include/configs/wireless_space.h')
| -rw-r--r-- | include/configs/wireless_space.h | 179 |
1 files changed, 0 insertions, 179 deletions
diff --git a/include/configs/wireless_space.h b/include/configs/wireless_space.h deleted file mode 100644 index 191ac1b73f..0000000000 --- a/include/configs/wireless_space.h +++ /dev/null @@ -1,179 +0,0 @@ -/* - * Copyright (C) 2011 Albert ARIBAUD <albert.u.boot@aribaud.net> - * - * Based on the netspace_v2 code which is - * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef _CONFIG_WIRELESS_SPACE_H -#define _CONFIG_WIRELESS_SPACE_H - -/* - * Machine number definition - */ -#define MACH_TYPE_WIRELESS_SPACE 2500 /* is missing in mach-types.h */ -#define CONFIG_MACH_TYPE MACH_TYPE_WIRELESS_SPACE -#define CONFIG_IDENT_STRING " Wireless Space" - -/* - * High Level Configuration Options (easy to change) - */ -#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */ -/* SoC name */ -#define CONFIG_KW88F6281 -#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ - -/* - * Commands configuration - */ -#define CONFIG_SYS_NO_FLASH /* no NOR or SPI flash */ -#define CONFIG_CMD_ENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_PING -#define CONFIG_CMD_NAND -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE -#define CONFIG_CMD_USB - -/* - * Core clock definition - */ -#define CONFIG_SYS_TCLK 166000000 /* 166MHz */ - -/* - * SDRAM configuration - */ -#define CONFIG_NR_DRAM_BANKS 1 - -/* - * Different SDRAM configuration and size for some of the boards derived - * from the Network Space v2 - */ - -/* - * mv-common.h should be defined after CMD configs since it used them - * to enable certain macros - */ -#include "mv-common.h" - -/* Remove or override few declarations from mv-common.h */ -#undef CONFIG_RBTREE -#undef CONFIG_SYS_IDE_MAXBUS -#undef CONFIG_SYS_IDE_MAXDEVICE -#define CONFIG_SYS_IDE_MAXBUS 1 -#define CONFIG_SYS_IDE_MAXDEVICE 1 - -/* - * Ethernet Driver configuration - */ -#ifdef CONFIG_CMD_NET -#define CONFIG_MISC_INIT_R /* misc_init_r() initializes MAC address */ -#define CONFIG_MVGBE_PORTS {1, 0} /* enable only egiga0... */ -#define PORT_SERIAL_CONTROL_VALUE 0x00A4260E /* ... tied to the switch... */ -#define CONFIG_PHY_BASE_ADR 0xa /* ... through a 'fake' PHY */ -#define CONFIG_MII -#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN -#define CONFIG_NETCONSOLE -#define CONFIG_MV88E61XX_SWITCH -#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE -#define CONFIG_MV88E61XX_CMD -#define CONFIG_CMD_TFTPPUT -#endif /* CONFIG_CMD_NET */ - -/* - * SATA Driver configuration - */ -#ifdef CONFIG_MVSATA_IDE -#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET -#endif /* CONFIG_MVSATA_IDE */ - -/* - * Enable GPI0 support - */ -#define CONFIG_KIRKWOOD_GPIO - -/* - * Enable I2C support - */ -#ifdef CONFIG_CMD_I2C -/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */ -#define CONFIG_CMD_EEPROM -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */ -#endif /* CONFIG_CMD_I2C */ - -/* - * Partition support - */ -#define CONFIG_DOS_PARTITION -#define CONFIG_EFI_PARTITION - -/* - * File systems support - */ -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT - -/* - * Use the HUSH parser - */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * Console configuration - */ -#define CONFIG_CONSOLE_MUX -#define CONFIG_SYS_CONSOLE_IS_IN_ENV - -/* - * Enable device tree support - */ -#define CONFIG_OF_LIBFDT - -/* - * Environment variables configurations - */ - -#define CONFIG_ENV_IS_IN_NAND -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128KB */ -#define CONFIG_ENV_SIZE 0x20000 /* 128KB */ -#define CONFIG_ENV_OFFSET 0x80000 /* env starts here */ - -/* - * Board-specific command to make using buttons etc easier - */ - -#define CONFIG_WIRELESS_SPACE_CMD - -/* - * Default environment variables - */ -#define CONFIG_PREBOOT - -#define CONFIG_BOOTARGS "console=ttyS0,115200" - -#define CONFIG_BOOTCOMMAND \ - "if run usbload || run diskload; then bootm; fi" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "stdin=serial\0" \ - "stdout=serial\0" \ - "stderr=serial\0" \ - "bootfile=uImage\0" \ - "loadaddr=0x800000\0" \ - "autoload=no\0" \ - "netconsole=" \ - "set stdin $stdin,nc; " \ - "set stdout $stdout,nc; " \ - "set stderr $stderr,nc;\0" \ - "diskload=ide reset && " \ - "ext2load ide 0:1 $loadaddr /boot/$bootfile\0" \ - "usbload=usb start && " \ - "fatload usb 0:1 $loadaddr /boot/$bootfile\0" \ - "preboot=" \ - "dhcp && run netconsole\0" - -#endif /* _CONFIG_WIRELESS_SPACE_H */ |