diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/am65x_evm.h | 67 |
1 files changed, 57 insertions, 10 deletions
diff --git a/include/configs/am65x_evm.h b/include/configs/am65x_evm.h index b043bf886b..1415bb1b15 100644 --- a/include/configs/am65x_evm.h +++ b/include/configs/am65x_evm.h @@ -19,6 +19,32 @@ #define CONFIG_SYS_SDRAM_BASE1 0x880000000 /* SPL Loader Configuration */ +#ifdef CONFIG_TARGET_AM654_A53_EVM +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \ + CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE) +#else +/* + * Maximum size in memory allocated to the SPL BSS. Keep it as tight as + * possible (to allow the build to go through), as this directly affects + * our memory footprint. The less we use for BSS the more we have available + * for everything else. + */ +#define CONFIG_SPL_BSS_MAX_SIZE 0x5000 +/* + * Link BSS to be within SPL in a dedicated region located near the top of + * the MCU SRAM, this way making it available also before relocation. Note + * that we are not using the actual top of the MCU SRAM as there is a memory + * location filled in by the boot ROM that we want to read out without any + * interference from the C context. + */ +#define CONFIG_SPL_BSS_START_ADDR (CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX -\ + CONFIG_SPL_BSS_MAX_SIZE) +/* Set the stack right below the SPL BSS section */ +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_BSS_START_ADDR +/* Configure R5 SPL post-relocation malloc pool in DDR */ +#define CONFIG_SYS_SPL_MALLOC_START 0x84000000 +#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M +#endif #ifdef CONFIG_SYS_K3_SPL_ATF #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "tispl.bin" @@ -29,26 +55,26 @@ #endif #define CONFIG_SPL_MAX_SIZE CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \ - CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE - 4) #define CONFIG_SYS_BOOTM_LEN SZ_64M +#define PARTS_DEFAULT \ + /* Linux partitions */ \ + "name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0" + /* U-Boot general configuration */ #define EXTRA_ENV_AM65X_BOARD_SETTINGS \ "findfdt=" \ - "if test $board_name = am65x; then " \ - "setenv name_fdt k3-am654-base-board.dtb; " \ - "else if test $name_fdt = undefined; then " \ - "echo WARNING: Could not determine device tree to use;"\ - "fi; fi; " \ - "setenv fdtfile ${name_fdt}\0" \ + "setenv name_fdt k3-am654-base-board.dtb;" \ + "setenv fdtfile ${name_fdt};" \ + "setenv overlay_files ${name_overlays}\0" \ "loadaddr=0x80080000\0" \ "fdtaddr=0x82000000\0" \ + "overlayaddr=0x83000000\0" \ "name_kern=Image\0" \ "console=ttyS2,115200n8\0" \ "args_all=setenv optargs earlycon=ns16550a,mmio32,0x02800000\0" \ - "run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0" + "run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0" \ /* U-Boot MMC-specific configuration */ #define EXTRA_ENV_AM65X_BOARD_SETTINGS_MMC \ @@ -59,8 +85,17 @@ "rd_spec=-\0" \ "init_mmc=run args_all args_mmc\0" \ "get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \ + "get_overlay_mmc=" \ + "fdt address ${fdtaddr};" \ + "fdt resize 0x100000;" \ + "for overlay in $overlay_files;" \ + "do;" \ + "load mmc ${bootpart} ${overlayaddr} ${bootdir}/${overlay};" \ + "fdt apply ${overlayaddr};" \ + "done;\0" \ "get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \ - "${bootdir}/${name_kern}\0" + "${bootdir}/${name_kern}\0" \ + "partitions=" PARTS_DEFAULT /* Incorporate settings into the U-Boot environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ @@ -68,6 +103,18 @@ EXTRA_ENV_AM65X_BOARD_SETTINGS \ EXTRA_ENV_AM65X_BOARD_SETTINGS_MMC +/* MMC ENV related defines */ +#ifdef CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_SYS_MMC_ENV_PART 1 +#define CONFIG_ENV_SIZE (128 << 10) +#define CONFIG_ENV_OFFSET 0x680000 +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +#endif + +#define CONFIG_SUPPORT_EMMC_BOOT + /* Now for the remaining common defines */ #include <configs/ti_armv7_common.h> |