diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/CRAYL1.h | 228 | ||||
| -rw-r--r-- | include/configs/KAREF.h | 284 | ||||
| -rw-r--r-- | include/configs/MERGERBOX.h | 599 | ||||
| -rw-r--r-- | include/configs/METROBOX.h | 349 | ||||
| -rw-r--r-- | include/configs/MIP405.h | 2 | ||||
| -rw-r--r-- | include/configs/MVBC_P.h | 300 | ||||
| -rw-r--r-- | include/configs/MVBLM7.h | 491 | ||||
| -rw-r--r-- | include/configs/MVSMR.h | 270 | ||||
| -rw-r--r-- | include/configs/PATI.h | 3 | ||||
| -rw-r--r-- | include/configs/PIP405.h | 2 | ||||
| -rw-r--r-- | include/configs/VCMA9.h | 3 | ||||
| -rw-r--r-- | include/configs/am335x_evm.h | 1 | ||||
| -rw-r--r-- | include/configs/axs101.h | 1 | ||||
| -rw-r--r-- | include/configs/bluestone.h | 168 | ||||
| -rw-r--r-- | include/configs/omap3_overo.h | 2 | ||||
| -rw-r--r-- | include/configs/omap5_uevm.h | 1 | ||||
| -rw-r--r-- | include/configs/siemens-am33x-common.h | 2 | ||||
| -rw-r--r-- | include/configs/socfpga_common.h | 196 | ||||
| -rw-r--r-- | include/configs/socfpga_cyclone5.h | 317 |
19 files changed, 273 insertions, 2946 deletions
diff --git a/include/configs/CRAYL1.h b/include/configs/CRAYL1.h deleted file mode 100644 index 788fa0f91c..0000000000 --- a/include/configs/CRAYL1.h +++ /dev/null @@ -1,228 +0,0 @@ -/* - * (C) Copyright 2000-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * David Updegraff, Cray, Inc. dave@cray.com: our 405 is walnut-lite.. - * - * SPDX-License-Identifier: GPL-2.0+ - */ -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_CRAYL1 -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_405GP 1 /* This is a PPC405 CPU */ - -/* - * Note: I make an "image" from U-Boot itself, which prefixes 0x40 - * bytes of header info, hence start address is thus shifted. - */ -#define CONFIG_SYS_TEXT_BASE 0xFFFD0040 - -#define CONFIG_SYS_CLK_FREQ 25000000 -#define CONFIG_BAUDRATE 9600 -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 1 /* PHY address; handling of ENET */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* early setup for 405gp */ -#define CONFIG_MISC_INIT_R 1 /* so that a misc_init_r() is called */ - -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() - -/* set PRAM to keep U-Boot out, mem= to keep linux out, and initrd_hi to - * keep possible initrd ramdisk decompression out. This is in k (1024 bytes) - #define CONFIG_PRAM 16 - */ -#define CONFIG_LOADADDR 0x100000 /* where TFTP images go */ -#undef CONFIG_BOOTARGS - -/* Bootcmd is overridden by the bootscript in board/cray/L1 - */ -#define CONFIG_SYS_AUTOLOAD "no" -#define CONFIG_BOOTCOMMAND "dhcp" - -/* - * ..during experiments.. - #define CONFIG_SERVERIP 10.0.0.1 - #define CONFIG_ETHADDR 00:40:a6:80:14:5 - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SDRAM_BANK0 1 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_IDENT_STRING "Cray L1" -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_SYS_HUSH_PARSER 1 -#define CONFIG_SOURCE 1 - - -/* - * Command line configuration. - */ - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_BDI -#define CONFIG_CMD_CONSOLE -#define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_FLASH -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IMI -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_MEMORY -#define CONFIG_CMD_NET -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_RUN -#define CONFIG_CMD_SAVEENV -#define CONFIG_CMD_SETGETDCR -#define CONFIG_CMD_SOURCE - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_VENDOREX -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_BOOTFILESIZE - - -/* - * how many time to fail & restart a net-TFTP before giving up & resetting - * the board hoping that a reset of net interface might help.. - */ -#define CONFIG_NET_RESET 5 - -/* - * bauds. Just to make it compile; in our case, I read the base_baud - * from the DCR anyway, so its kinda-tied to the above ref. clock which in turn - * drives the system clock. - */ -#define CONFIG_SYS_BASE_BAUD 403225 -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ - - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* where to load what we get from TFTP */ -#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_SYS_DRAM_TEST 1 - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0xFFC00000 -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE - - -#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 192 kB for Monitor */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -/* BEG ENVIRONNEMENT FLASH: needs to be a whole FlashSector */ -#define CONFIG_ENV_OFFSET 0x3c8000 -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment area */ -#define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sector total size */ - -/* Memory tests: U-BOOT relocates itself to the top of Ram, so its at - * 32meg-(128k+some_malloc_space+copy-of-ENV sector).. - */ -#define CONFIG_SYS_SDRAM_SIZE 32 /* megs of ram */ -#define CONFIG_SYS_MEMTEST_START 0x2000 /* memtest works from the end of */ - /* the exception vector table */ - /* to the end of the DRAM */ - /* less monitor and malloc area */ -#define CONFIG_SYS_STACK_USAGE 0x10000 /* Reserve 64k for the stack usage */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* 128k for malloc space */ -#define CONFIG_SYS_MEM_END_USAGE ( CONFIG_SYS_MONITOR_LEN \ - + CONFIG_SYS_MALLOC_LEN \ - + CONFIG_ENV_SECT_SIZE \ - + CONFIG_SYS_STACK_USAGE ) - -#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 - CONFIG_SYS_MEM_END_USAGE) -/* END ENVIRONNEMENT FLASH */ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ - - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in OnChipMem ) - */ -#if 1 -/* On Chip Memory location */ -#define CONFIG_SYS_TEMP_STACK_OCM 1 -#define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 - -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#else -#define CONFIG_SYS_OCM_DATA_ADDR 0xF0000000 -#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of On Chip SRAM */ -#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of On Chip SRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#endif - -/*----------------------------------------------------------------------- - * Definitions for Serial Presence Detect EEPROM address - */ -#define EEPROM_WRITE_ADDRESS 0xA0 -#define EEPROM_READ_ADDRESS 0xA1 - -#endif /* __CONFIG_H */ diff --git a/include/configs/KAREF.h b/include/configs/KAREF.h deleted file mode 100644 index 546b725317..0000000000 --- a/include/configs/KAREF.h +++ /dev/null @@ -1,284 +0,0 @@ -/* - * (C) Copyright 2004 Sandburst Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************ - * KAMINOREFDES.h - configuration for the Sandburst Kamino Reference - * design. - ***********************************************************************/ - -/* - * $Id: KAREF.h,v 1.6 2005/06/03 15:05:25 tsawyer Exp $ - * - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*----------------------------------------------------------------------- - * High Level Configuration Options - *----------------------------------------------------------------------*/ -#define CONFIG_KAREF 1 /* Board is Kamino Ref Variant */ -#define CONFIG_440GX 1 /* Specifc GX support */ -#define CONFIG_440 1 /* ... PPC440 family */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#define CONFIG_MISC_INIT_F 1 /* Call board misc_init_f */ -#define CONFIG_MISC_INIT_R 1 /* Call board misc_init_r */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF80000 - -#undef CONFIG_SYS_DRAM_TEST /* Disable-takes long time!*/ -#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ - -#define CONFIG_VERY_BIG_RAM 1 -#define CONFIG_VERSION_VARIABLE - -#define CONFIG_IDENT_STRING " Sandburst Kamino Reference Design" - -/*----------------------------------------------------------------------- - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */ -#define CONFIG_SYS_MONITOR_BASE 0xfff80000 /* start of monitor */ -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ -#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ - -#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) -#define CONFIG_SYS_KAREF_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08200000) -#define CONFIG_SYS_OFEM_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08400000) -#define CONFIG_SYS_BME32_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08500000) -#define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700) - -/* Here for completeness */ -#define CONFIG_SYS_OFEMAC_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08600000) - -/*----------------------------------------------------------------------- - * Initial RAM & stack pointer (placed in internal SRAM) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_TEMP_STACK_OCM 1 -#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Rsrv 256kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Rsrv 128kB for malloc */ - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() -#define CONFIG_BAUDRATE 9600 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -/*----------------------------------------------------------------------- - * NVRAM/RTC - * - * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located. - * The DS1743 code assumes this condition (i.e. -- it assumes the base - * address for the RTC registers is: - * - * CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE - * - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs*/ -#define CONFIG_RTC_DS174x 1 /* DS1743 RTC */ - -/*----------------------------------------------------------------------- - * FLASH related - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 8 /* sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase TO (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO(in ms) */ - -/*----------------------------------------------------------------------- - * DDR SDRAM - *----------------------------------------------------------------------*/ -#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup*/ -#define SPD_EEPROM_ADDRESS {0x53} /* SPD i2c spd addresses */ - -/*----------------------------------------------------------------------- - * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F -#define CONFIG_SYS_I2C_PPC4XX_CH1 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 400000 /* I2C speed 400kHz */ -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F -#define CONFIG_SYS_I2C_NOPROBES { { 0, 0x69} } /* Don't probe these addrs */ - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_NVRAM 1 /* Environment uses NVRAM */ -#undef CONFIG_ENV_IS_IN_FLASH /* ... not in flash */ -#undef CONFIG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ -#define CONFIG_ENV_OVERWRITE 1 /* allow env overwrite */ - -#define CONFIG_ENV_SIZE 0x1000 /* Size of Env vars */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_NVRAM_BASE_ADDR) - -#define CONFIG_BOOTDELAY 5 /* 5 second autoboot */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial dnld */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/*----------------------------------------------------------------------- - * Networking - *----------------------------------------------------------------------*/ -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */ -#define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */ -#define CONFIG_PHY2_ADDR 0x08 /* PHY addr, MGMT, EMAC2 */ -#define CONFIG_PHY3_ADDR 0x18 /* PHY addr, LCL, EMAC3 */ -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#define CONFIG_HAS_ETH3 -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CONFIG_CIS8201_PHY 1 /* RGMII mode for Cicada */ -#define CONFIG_CIS8201_SHORT_ETCH 1 /* Use short etch mode */ -#define CONFIG_PHY_GIGE 1 /* GbE speed/duplex detect */ -#define CONFIG_PHY_RESET_DELAY 1000 -#define CONFIG_NETMASK 255.255.0.0 -#define CONFIG_ETHADDR 00:00:00:00:00:00 /* No EMAC 0 support */ -#define CONFIG_ETH1ADDR 00:00:00:00:00:00 /* No EMAC 1 support */ -#define CONFIG_SYS_RX_ETH_BUFFER 32 /* #eth rx buff & descrs */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PCI -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_I2C -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DATE -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_PING -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_ELF -#define CONFIG_CMD_IDE -#define CONFIG_CMD_FAT - - -/* Include NetConsole support */ -#define CONFIG_NETCONSOLE - -/* Include auto complete with tabs */ -#define CONFIG_AUTO_COMPLETE 1 -#define CONFIG_SYS_ALT_MEMTEST 1 /* use real memory test */ - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "KaRefDes=> " /* Monitor Command Prompt */ - -#define CONFIG_SYS_HUSH_PARSER 1 /* HUSH for ext'd cli */ - - -/*----------------------------------------------------------------------- - * Console Buffer - *----------------------------------------------------------------------*/ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) - /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */ - -/*----------------------------------------------------------------------- - * Memory Test - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/*----------------------------------------------------------------------- - * Compact Flash (in true IDE mode) - *----------------------------------------------------------------------*/ -#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ -#undef CONFIG_IDE_LED /* no led for ide supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ - -#define CONFIG_SYS_ATA_BASE_ADDR 0xF0000000 -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses*/ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x100000 /* Offset for alternate registers */ - -#define CONFIG_SYS_ATA_STRIDE 2 /* Directly connected CF, needs a stride - to get to the correct offset */ -#define CONFIG_DOS_PARTITION 1 /* Include dos partition */ - -/*----------------------------------------------------------------------- - * PCI - *----------------------------------------------------------------------*/ -/* General PCI */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices */ -#define CONFIG_SYS_PCI_TARGBASE (CONFIG_SYS_PCI_MEMBASE) - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target*/ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x17BA /* Sandburst */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* kgdb serial port baud */ -#endif - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_SYS_LOAD_ADDR 0x8000000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/MERGERBOX.h b/include/configs/MERGERBOX.h deleted file mode 100644 index 19ea3167af..0000000000 --- a/include/configs/MERGERBOX.h +++ /dev/null @@ -1,599 +0,0 @@ -/* - * Copyright (C) 2007 Freescale Semiconductor, Inc. - * - * Copyright (C) 2011 Matrix Vision GmbH - * Andre Schwarz <andre.schwarz@matrix-vision.de> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <version.h> - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 -#define CONFIG_MPC837x 1 -#define CONFIG_MPC8377 1 - -#define CONFIG_SYS_TEXT_BASE 0xFC000000 - -#define CONFIG_PCI 1 -#define CONFIG_PCI_INDIRECT_BRIDGE 1 - -#define CONFIG_MASK_AER_AO -#define CONFIG_DISPLAY_AER_FULL - -#define CONFIG_MISC_INIT_R - -/* - * On-board devices - */ -#define CONFIG_TSEC_ENET - -/* - * System Clock Setup - */ -#define CONFIG_83XX_CLKIN 66666667 /* in Hz */ -#define CONFIG_PCIE -#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES -#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN - -/* - * Hardware Reset Configuration Word stored in EEPROM. - */ -#define CONFIG_SYS_HRCW_LOW 0 -#define CONFIG_SYS_HRCW_HIGH 0 - -/* Arbiter Configuration Register */ -#define CONFIG_SYS_ACR_PIPE_DEP 3 -#define CONFIG_SYS_ACR_RPTCNT 3 - -/* System Priority Control Regsiter */ -#define CONFIG_SYS_SPCR_TSECEP 3 - -/* System Clock Configuration Register */ -#define CONFIG_SYS_SCCR_TSEC1CM 3 -#define CONFIG_SYS_SCCR_TSEC2CM 0 -#define CONFIG_SYS_SCCR_SDHCCM 3 -#define CONFIG_SYS_SCCR_ENCCM 3 /* also clock for I2C-1 */ -#define CONFIG_SYS_SCCR_USBDRCM CONFIG_SYS_SCCR_ENCCM /* must match */ -#define CONFIG_SYS_SCCR_PCIEXP1CM 3 -#define CONFIG_SYS_SCCR_PCIEXP2CM 3 -#define CONFIG_SYS_SCCR_PCICM 1 -#define CONFIG_SYS_SCCR_SATACM 0xFF - -/* - * System IO Config - */ -#define CONFIG_SYS_SICRH 0x087c0000 -#define CONFIG_SYS_SICRL 0x40000000 - -/* - * Output Buffer Impedance - */ -#define CONFIG_SYS_OBIR 0x30000000 - -/* - * IMMR new address - */ -#define CONFIG_SYS_IMMR 0xE0000000 - -/* - * DDR Setup - */ -#define CONFIG_SYS_DDR_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_83XX_DDR_USES_CS0 - -#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN | DDRCDR_PZ_HIZ |\ - DDRCDR_NZ_HIZ | DDRCDR_ODT |\ - DDRCDR_Q_DRN) - -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 - -#define CONFIG_SYS_DDR_MODE_WEAK -#define CONFIG_SYS_DDR_WRITE_DATA_DELAY 2 -#define CONFIG_SYS_DDR_CPO 0x1f - -/* SPD table located at offset 0x20 in extended adressing ROM - * used for HRCW fetch after power-on reset - */ -#define CONFIG_SPD_EEPROM -#define SPD_EEPROM_ADDRESS 0x50 -#define SPD_EEPROM_OFFSET 0x20 -#define SPD_EEPROM_ADDR_LEN 2 - -/* - * The reserved memory - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_MONITOR_LEN (512*1024) -#define CONFIG_SYS_MALLOC_LEN (512*1024) - -/* - * Initial RAM Base Address Setup - */ -#define CONFIG_SYS_INIT_RAM_LOCK 1 -#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -\ - GENERATED_GBL_DATA_SIZE) - -/* - * Local Bus Configuration & Clock Setup - */ -#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP -#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8 -#define CONFIG_SYS_LBC_LBCR 0x00000000 -#define CONFIG_FSL_ELBC 1 - -/* - * FLASH on the Local Bus - */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_FLASH_SIZE 64 - -#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_PS_16 |\ - BR_MS_GPCM | BR_V) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_FLASH_BASE | OR_UPM_XAM |\ - OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 |\ - OR_GPCM_XACS | OR_GPCM_SCY_15 |\ - OR_GPCM_TRLX_SET | OR_GPCM_EHTR_SET |\ - OR_GPCM_EAD) - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 512 - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ - -/* - * NAND Flash on the Local Bus - */ -#define CONFIG_MTD_NAND_VERIFY_WRITE 1 -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_NAND_FSL_ELBC 1 - -#define CONFIG_SYS_NAND_BASE 0xE0600000 -#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE | BR_DECC_CHK_GEN |\ - BR_PS_8 | BR_MS_FCM | BR_V) -#define CONFIG_SYS_OR1_PRELIM (OR_AM_32KB | OR_FCM_BCTLD | OR_FCM_CST |\ - OR_FCM_CHT | OR_FCM_SCY_1 | OR_FCM_RST |\ - OR_FCM_TRLX | OR_FCM_EHTR) - -#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE -#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_32KB) - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) - -#define CONFIG_CONSOLE ttyS0 -#define CONFIG_BAUDRATE 115200 - -/* SERDES */ -#define CONFIG_FSL_SERDES -#define CONFIG_FSL_SERDES1 0xe3000 -#define CONFIG_FSL_SERDES2 0xe3100 - -/* Use the HUSH parser */ -#define CONFIG_SYS_HUSH_PARSER - -/* Pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 400000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 400000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 - -/* - * General PCI - * Addresses are mapped 1-1. - */ -#define CONFIG_SYS_PCI_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BASE -#define CONFIG_SYS_PCI_MEM_SIZE (256 << 20) -#define CONFIG_SYS_PCI_MMIO_BASE 0x90000000 -#define CONFIG_SYS_PCI_MMIO_PHYS CONFIG_SYS_PCI_MMIO_BASE -#define CONFIG_SYS_PCI_MMIO_SIZE (256 << 20) -#define CONFIG_SYS_PCI_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI_IO_PHYS 0xE0300000 -#define CONFIG_SYS_PCI_IO_SIZE (1 << 20) - -#ifdef CONFIG_PCIE -#define CONFIG_SYS_PCIE1_BASE 0xA0000000 -#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000 -#define CONFIG_SYS_PCIE1_CFG_SIZE (128 << 20) -#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000 -#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000 -#define CONFIG_SYS_PCIE1_MEM_SIZE (256 << 20) -#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000 -#define CONFIG_SYS_PCIE1_IO_SIZE (8 << 20) - -#define CONFIG_SYS_PCIE2_BASE 0xC0000000 -#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000 -#define CONFIG_SYS_PCIE2_CFG_SIZE (128 << 20) -#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000 -#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000 -#define CONFIG_SYS_PCIE2_MEM_SIZE (256 << 20) -#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000 -#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000 -#define CONFIG_SYS_PCIE2_IO_SIZE (8 << 20) -#endif - -#define CONFIG_PCI_PNP -#define CONFIG_PCI_SCAN_SHOW -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ - -/* - * TSEC - */ -#define CONFIG_GMII /* MII PHY management */ -#define CONFIG_SYS_VSC8601_SKEWFIX -#define CONFIG_SYS_VSC8601_SKEW_TX 3 -#define CONFIG_SYS_VSC8601_SKEW_RX 3 - -#define CONFIG_TSEC1 -#define CONFIG_HAS_ETH0 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define TSEC1_PHY_ADDR 0x10 -#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) -#define TSEC1_PHYIDX 0 - -#define CONFIG_ETHPRIME "TSEC0" -#define CONFIG_HAS_ETH0 - -/* - * SATA - */ -#define CONFIG_LIBATA -#define CONFIG_FSL_SATA - -#define CONFIG_SYS_SATA_MAX_DEVICE 2 -#define CONFIG_SATA1 -#define CONFIG_SYS_SATA1_OFFSET 0x18000 -#define CONFIG_SYS_SATA1 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET) -#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA -#define CONFIG_SATA2 -#define CONFIG_SYS_SATA2_OFFSET 0x19000 -#define CONFIG_SYS_SATA2 (CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET) -#define CONFIG_SYS_SATA2_FLAGS FLAGS_DMA - -#define CONFIG_LBA48 -#define CONFIG_CMD_SATA -#define CONFIG_DOS_PARTITION -#define CONFIG_CMD_EXT2 - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_VENDOREX -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_NTPSERVER -#define CONFIG_BOOTP_RANDOM_DELAY -#define CONFIG_BOOTP_SEND_HOSTNAME -#define CONFIG_LIB_RAND - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_NAND -#define CONFIG_CMD_PING -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_MII -#define CONFIG_CMD_PCI -#define CONFIG_CMD_USB -#define CONFIG_CMD_SPI -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_UBI -#define CONFIG_CMD_UBIFS -#define CONFIG_CMD_MTDPARTS -#define CONFIG_CMD_SATA - -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_JFFS2 - -#define CONFIG_RBTREE -#define CONFIG_LZO - -#define CONFIG_MTD_DEVICE -#define CONFIG_MTD_PARTITIONS - -#define CONFIG_FLASH_CFI_MTD -#define MTDIDS_DEFAULT "nor0=NOR,nand0=NAND" -#define MTDPARTS_DEFAULT "mtdparts=NOR:1M(u-boot),2M(FPGA);NAND:-(root)" - -#define CONFIG_FIT -#define CONFIG_FIT_VERBOSE 1 - -#define CONFIG_CMDLINE_EDITING 1 -#define CONFIG_AUTO_COMPLETE - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_LOAD_ADDR 0x2000000 -#define CONFIG_LOADADDR 0x4000000 -#define CONFIG_SYS_CBSIZE 256 - -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_LOADS_ECHO 1 -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 - -#define CONFIG_SYS_MEMTEST_START (60<<20) -#define CONFIG_SYS_MEMTEST_END (70<<20) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ - -/* - * Core HID Setup - */ -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ - HID0_ENABLE_INSTRUCTION_CACHE) -#define CONFIG_SYS_HID2 HID2_HBE - -/* - * MMU Setup - */ -#define CONFIG_HIGH_BATS 1 - -/* DDR: cache cacheable */ -#define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE - -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM | BATL_PP_RW |\ - BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM | BATU_BL_256M | BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U - -/* unused */ -#define CONFIG_SYS_IBAT1L (0) -#define CONFIG_SYS_IBAT1U (0) -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U - -/* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_IMMR | BATL_PP_RW |\ - BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_IMMR | BATU_BL_8M | BATU_VS |\ - BATU_VP) -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U - -/* unused */ -#define CONFIG_SYS_IBAT3L (0) -#define CONFIG_SYS_IBAT3U (0) -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U - -/* FLASH: icache cacheable, but dcache-inhibit and guarded */ -#define CONFIG_SYS_IBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW |\ - BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT4U (CONFIG_SYS_FLASH_BASE | BATU_BL_64M |\ - BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT4L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ - BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U - -/* Stack in dcache: cacheable, no memory coherence */ -#define CONFIG_SYS_IBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) -#define CONFIG_SYS_IBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K |\ - BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L -#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U - -/* PCI MEM space: cacheable */ -#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI_MEM_PHYS | BATL_PP_RW |\ - BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI_MEM_PHYS | BATU_BL_256M |\ - BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U - -/* PCI MMIO space: cache-inhibit and guarded */ -#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI_MMIO_PHYS | BATL_PP_RW | \ - BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI_MMIO_PHYS | BATU_BL_256M |\ - BATU_VS | BATU_VP) -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U - -/* - * I2C EEPROM settings - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_SIZE 0x4000 - -/* - * Environment Configuration - */ -#define CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_ENV_OVERWRITE -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0xFFD00000 -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE - -/* - * Video - */ -#define CONFIG_VIDEO -#define CONFIG_VIDEO_SM501_PCI -#define VIDEO_FB_LITTLE_ENDIAN -#define CONFIG_CMD_BMP -#define CONFIG_VIDEO_SM501 -#define CONFIG_VIDEO_SM501_32BPP -#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000 -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_BMP_LOGO -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SPLASH_SCREEN -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define CONFIG_VIDEO_BMP_GZIP -#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (2 << 20) - -/* - * SPI - */ -#define CONFIG_MPC8XXX_SPI - -/* - * USB - */ -#define CONFIG_SYS_USB_HOST -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_FSL -#define CONFIG_HAS_FSL_DR_USB -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET - -#define CONFIG_USB_STORAGE -#define CONFIG_USB_KEYBOARD -/* - * - */ -#define CONFIG_BOOTDELAY 5 -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_STOP_STR "s" -#define CONFIG_ZERO_BOOTDELAY_CHECK -#define CONFIG_RESET_TO_RETRY 1000 - -#define MV_CI "MergerBox" -#define MV_VCI "MergerBox" -#define MV_FPGA_DATA 0xfc100000 -#define MV_FPGA_SIZE 0x00200000 - -#define CONFIG_SHOW_BOOT_PROGRESS 1 - -#define MV_KERNEL_ADDR_RAM 0x02800000 -#define MV_DTB_ADDR_RAM 0x00600000 -#define MV_INITRD_ADDR_RAM 0x01000000 -#define MV_FITADDR 0xfc300000 -#define MV_SPLAH_ADDR 0xffe00000 - -#define CONFIG_BOOTCOMMAND "run i2c_init;if test ${boot_sqfs} -eq 1;"\ - "then; run fitboot;else;run ubiboot;fi;" -#define CONFIG_BOOTARGS "console=ttyS0,115200n8" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "console_nr=0\0"\ - "stdin=serial\0"\ - "stdout=serial\0"\ - "stderr=serial\0"\ - "boot_sqfs=1\0"\ - "usb_dr_mode=host\0"\ - "bootfile=MergerBox.fit\0"\ - "baudrate=" __stringify(CONFIG_BAUDRATE) "\0"\ - "fpga=0\0"\ - "fpgadata=" __stringify(MV_FPGA_DATA) "\0"\ - "fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0"\ - "mv_kernel_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0"\ - "mv_initrd_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0"\ - "mv_dtb_ram=" __stringify(MV_DTB_ADDR_RAM) "\0"\ - "uboota=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"\ - "fitaddr=" __stringify(MV_FITADDR) "\0"\ - "mv_version=" U_BOOT_VERSION "\0"\ - "mtdids=" MTDIDS_DEFAULT "\0"\ - "mtdparts=" MTDPARTS_DEFAULT "\0"\ - "dhcp_client_id=" MV_CI "\0"\ - "dhcp_vendor-class-identifier=" MV_VCI "\0"\ - "upd_uboot=dhcp;tftp bdi2000/u-boot-mergerbox-xp.bin;"\ - "protect off all;erase $uboota +0xC0000;"\ - "cp.b $loadaddr $uboota $filesize\0"\ - "upd_fpga=dhcp;tftp MergerBox.rbf;erase $fpgadata +$fpgadatasize;"\ - "cp.b $loadaddr $fpgadata $filesize\0"\ - "upd_fit=dhcp;tftp MergerBox.fit;erase $fitaddr +0x1000000;"\ - "cp.b $loadaddr $fitaddr $filesize\0"\ - "addsqshrfs=set bootargs $bootargs root=/dev/ram ro "\ - "rootfstype=squashfs\0"\ - "addubirfs=set bootargs $bootargs ubi.mtd=9 root=ubi0:rootfs rw "\ - "rootfstype=ubifs\0"\ - "addusbrfs=set bootargs $bootargs root=/dev/sda1 rw "\ - "rootfstype=ext3 usb-storage.delay_use=1 rootdelay=3\0"\ - "netusbboot=bootp;run fpganetload fitnetload addusbrfs doboot\0"\ - "netubiboot= bootp;run fpganetload fitnetload addubirfs doboot\0"\ - "ubiboot=run fitprep addubirfs;set mv_initrd_ram -;run doboot\0"\ - "doboot=bootm $mv_kernel_ram $mv_initrd_ram $mv_dtb_ram\0"\ - "fitprep=imxtract $fitaddr kernel $mv_kernel_ram;"\ - "imxtract $fitaddr ramdisk $mv_initrd_ram;"\ - "imxtract $fitaddr fdt $mv_dtb_ram\0"\ - "fdtprep=fdt addr $mv_dtb_ram;fdt boardsetup\0"\ - "fitboot=run fitprep fdtprep addsqshrfs doboot\0"\ - "i2c_init=run i2c_speed init_sdi_tx i2c_init_pll\0"\ - "i2c_init_pll=i2c mw 65 9 2;i2c mw 65 9 0;i2c mw 65 5 2b;"\ - "i2c mw 65 7 f;i2c mw 65 8 f;i2c mw 65 11 40;i2c mw 65 12 40;"\ - "i2c mw 65 13 40; i2c mw 65 14 40; i2c mw 65 a 0\0"\ - "i2c_speed=i2c dev 0;i2c speed 300000;i2c dev 1;i2c speed 120000\0"\ - "init_sdi_tx=i2c mw 21 6 0;i2c mw 21 2 0;i2c mw 21 3 0;sleep 1;"\ - "i2c mw 21 2 ff;i2c mw 21 3 3c\0"\ - "splashimage=" __stringify(MV_SPLAH_ADDR) "\0"\ - "" - -/* - * FPGA - */ -#define CONFIG_FPGA_COUNT 1 -#define CONFIG_FPGA -#define CONFIG_FPGA_ALTERA -#define CONFIG_FPGA_CYCLON2 - -#endif diff --git a/include/configs/METROBOX.h b/include/configs/METROBOX.h deleted file mode 100644 index 69ab5bb517..0000000000 --- a/include/configs/METROBOX.h +++ /dev/null @@ -1,349 +0,0 @@ -/* - * (C) Copyright 2004 Sandburst Corporation - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************ - * METROBOX.h - configuration Sandburst MetroBox - ***********************************************************************/ - -/* - * $Id: METROBOX.h,v 1.21 2005/06/03 15:05:25 tsawyer Exp $ - * - * - * $Log: METROBOX.h,v $ - * Revision 1.21 2005/06/03 15:05:25 tsawyer - * MB rev 2.0.3 KA rev 0.0.7. Add CONFIG_VERSION_VARIABLE, Add fakeled to MB - * - * Revision 1.20 2005/04/11 20:51:11 tsawyer - * fix ethernet - * - * Revision 1.19 2005/04/06 15:13:36 tsawyer - * Update appropriate files to coincide with u-boot 1.1.3 - * - * Revision 1.18 2005/03/10 14:16:02 tsawyer - * add def'n for cis8201 short etch option. - * - * Revision 1.17 2005/03/09 19:49:51 tsawyer - * Remove KGDB to allow use of 2nd serial port - * - * Revision 1.16 2004/12/02 19:00:23 tsawyer - * Add misc_init_f to turn on i2c-1 and all four fans before sdram init - * - * Revision 1.15 2004/09/15 18:04:12 tsawyer - * add multiple serial port support - * - * Revision 1.14 2004/09/03 15:27:51 tsawyer - * All metrobox boards are at 66.66 sys clock - * - * Revision 1.13 2004/08/05 20:27:46 tsawyer - * Remove system ace definitions, add net console support - * - * Revision 1.12 2004/07/29 20:00:13 tsawyer - * Add i2c bus 1 - * - * Revision 1.11 2004/07/21 13:44:18 tsawyer - * SystemACE is out, CF direct to local bus is in - * - * Revision 1.10 2004/06/29 19:08:55 tsawyer - * Add CONFIG_MISC_INIT_R - * - * Revision 1.9 2004/06/28 21:30:53 tsawyer - * Fix default BOOTARGS - * - * Revision 1.8 2004/06/17 15:51:08 tsawyer - * auto complete - * - * Revision 1.7 2004/06/17 15:08:49 tsawyer - * Add autocomplete - * - * Revision 1.6 2004/06/15 12:33:57 tsawyer - * debugging checkpoint - * - * Revision 1.5 2004/06/12 19:48:28 tsawyer - * Debugging checkpoint - * - * Revision 1.4 2004/06/02 13:03:06 tsawyer - * Fix eth addrs - * - * Revision 1.3 2004/05/18 19:56:10 tsawyer - * Change default bootcommand to pImage.metrobox - * - * Revision 1.2 2004/05/18 14:13:44 tsawyer - * Add bringup values for bootargs and bootcommand. - * Remove definition of ipaddress and serverip addresses. - * - * Revision 1.1 2004/04/16 15:08:54 tsawyer - * Initial Revision - * - * - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/*----------------------------------------------------------------------- - * High Level Configuration Options - *----------------------------------------------------------------------*/ -#define CONFIG_METROBOX 1 /* Board is Metrobox */ -#define CONFIG_440GX 1 /* Specifc GX support */ -#define CONFIG_440 1 /* ... PPC440 family */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#define CONFIG_MISC_INIT_F 1 /* Call board misc_init_f */ -#define CONFIG_MISC_INIT_R 1 /* Call board misc_init_r */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF80000 - -#undef CONFIG_SYS_DRAM_TEST /* Disable-takes long time!*/ -#define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ - -#define CONFIG_VERY_BIG_RAM 1 -#define CONFIG_VERSION_VARIABLE - -#define CONFIG_IDENT_STRING " Sandburst Metrobox" - -/*----------------------------------------------------------------------- - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CONFIG_SYS_FLASH_BASE 0xfff80000 /* start of FLASH */ -#define CONFIG_SYS_MONITOR_BASE 0xfff80000 /* start of monitor */ -#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ -#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ - -#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) -#define CONFIG_SYS_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08200000) -#define CONFIG_SYS_BME32_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08500000) -#define CONFIG_SYS_GPIO_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000700) - -/*----------------------------------------------------------------------- - * Initial RAM & stack pointer (placed in internal SRAM) - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_TEMP_STACK_OCM 1 -#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) - -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Rsrv 256kB for Mon */ -#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Rsrv 128kB for malloc */ - -/*----------------------------------------------------------------------- - * Serial Port - *----------------------------------------------------------------------*/ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_serial_clock() -#define CONFIG_BAUDRATE 9600 - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - -/*----------------------------------------------------------------------- - * NVRAM/RTC - * - * NOTE: Upper 8 bytes of NVRAM is where the RTC registers are located. - * The DS1743 code assumes this condition (i.e. -- it assumes the base - * address for the RTC registers is: - * - * CONFIG_SYS_NVRAM_BASE_ADDR + CONFIG_SYS_NVRAM_SIZE - * - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_NVRAM_SIZE (0x2000 - 8) /* NVRAM size(8k)- RTC regs*/ -#define CONFIG_RTC_DS174x 1 /* DS1743 RTC */ - -/*----------------------------------------------------------------------- - * FLASH related - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 8 /* sectors per device */ - -#undef CONFIG_SYS_FLASH_CHECKSUM -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Flash Erase TO (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO(in ms) */ - -/*----------------------------------------------------------------------- - * DDR SDRAM - *----------------------------------------------------------------------*/ -#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup*/ -#define SPD_EEPROM_ADDRESS {0x53} /* SPD i2c spd addresses */ - -/*----------------------------------------------------------------------- - * I2C - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_PPC4XX -#define CONFIG_SYS_I2C_PPC4XX_CH0 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F -#define CONFIG_SYS_I2C_PPC4XX_CH1 -#define CONFIG_SYS_I2C_PPC4XX_SPEED_1 400000 /* I2C speed 400kHz */ -#define CONFIG_SYS_I2C_PPC4XX_SLAVE_1 0x7F -#define CONFIG_SYS_I2C_NOPROBES { { 0, 0x69} } /* Don't probe these addrs */ - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#define CONFIG_ENV_IS_IN_NVRAM 1 /* Environment uses NVRAM */ -#undef CONFIG_ENV_IS_IN_FLASH /* ... not in flash */ -#undef CONFIG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ -#define CONFIG_ENV_OVERWRITE 1 /* allow env overwrite */ - -#define CONFIG_ENV_SIZE 0x1000 /* Size of Env vars */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_NVRAM_BASE_ADDR) - -#define CONFIG_BOOTARGS "console=ttyS0,9600 root=/dev/nfs rw nfsroot=$serverip:/home/metrobox0 nfsaddrs=$ipaddr:::::eth0:none " -#define CONFIG_BOOTCOMMAND "tftp 8000000 pImage.metrobox;bootm 8000000" -#define CONFIG_BOOTDELAY 5 /* disable autoboot */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial dnld */ -#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -/*----------------------------------------------------------------------- - * Networking - *----------------------------------------------------------------------*/ -#define CONFIG_PPC4xx_EMAC -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */ -#define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */ -#define CONFIG_PHY2_ADDR 0x08 /* PHY addr, MGMT, EMAC2 */ -#define CONFIG_PHY3_ADDR 0x18 /* PHY addr, LCL, EMAC3 */ -#define CONFIG_HAS_ETH0 -#define CONFIG_HAS_ETH1 -#define CONFIG_HAS_ETH2 -#define CONFIG_HAS_ETH3 -#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ -#define CONFIG_CIS8201_PHY 1 /* RGMII mode for Cicada */ -#define CONFIG_CIS8201_SHORT_ETCH 1 /* Use short etch mode */ -#define CONFIG_PHY_GIGE 1 /* GbE speed/duplex detect */ -#define CONFIG_PHY_RESET_DELAY 1000 -#define CONFIG_NETMASK 255.255.0.0 -#define CONFIG_ETHADDR 00:00:00:00:00:00 /* No EMAC 0 support */ -#define CONFIG_ETH1ADDR 00:00:00:00:00:00 /* No EMAC 1 support */ -#define CONFIG_SYS_RX_ETH_BUFFER 32 /* #eth rx buff & descrs */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_PCI -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_I2C -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DATE -#define CONFIG_CMD_BEDBUG -#define CONFIG_CMD_PING -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_ELF -#define CONFIG_CMD_IDE -#define CONFIG_CMD_FAT - - -/* Include NetConsole support */ -#define CONFIG_NETCONSOLE - -/* Include auto complete with tabs */ -#define CONFIG_AUTO_COMPLETE 1 -#define CONFIG_AUTO_COMPLETE 1 -#define CONFIG_SYS_ALT_MEMTEST 1 /* use real memory test */ - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "MetroBox=> " /* Monitor Command Prompt */ - -#define CONFIG_SYS_HUSH_PARSER 1 /* HUSH for ext'd cli */ - - -/*----------------------------------------------------------------------- - * Console Buffer - *----------------------------------------------------------------------*/ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) - /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buffer Size */ - -/*----------------------------------------------------------------------- - * Memory Test - *----------------------------------------------------------------------*/ -#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/*----------------------------------------------------------------------- - * Compact Flash (in true IDE mode) - *----------------------------------------------------------------------*/ -#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ -#undef CONFIG_IDE_LED /* no led for ide supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ - -#define CONFIG_SYS_ATA_BASE_ADDR 0xF0000000 -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses*/ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x100000 /* Offset for alternate registers */ - -#define CONFIG_SYS_ATA_STRIDE 2 /* Directly connected CF, needs a stride - to get to the correct offset */ -#define CONFIG_DOS_PARTITION 1 /* Include dos partition */ - -/*----------------------------------------------------------------------- - * PCI - *----------------------------------------------------------------------*/ -/* General PCI */ -#define CONFIG_PCI /* include pci support */ -#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ -#define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices */ -#define CONFIG_SYS_PCI_TARGBASE (CONFIG_SYS_PCI_MEMBASE) - -/* Board-specific PCI */ -#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target*/ - -#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x17BA /* Sandburst */ -#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* kgdb serial port baud */ -#endif - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#undef CONFIG_WATCHDOG /* watchdog disabled */ -#define CONFIG_SYS_LOAD_ADDR 0x8000000 /* default load address */ -#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/MIP405.h b/include/configs/MIP405.h index 68824fd2d4..147f122967 100644 --- a/include/configs/MIP405.h +++ b/include/configs/MIP405.h @@ -21,6 +21,8 @@ #define CONFIG_SYS_TEXT_BASE 0xFFF80000 +#define CONFIG_SYS_GENERIC_BOARD + /*********************************************************** * Note that it may also be a MIP405T board which is a subset of the * MIP405 diff --git a/include/configs/MVBC_P.h b/include/configs/MVBC_P.h deleted file mode 100644 index 1ab2b3d51a..0000000000 --- a/include/configs/MVBC_P.h +++ /dev/null @@ -1,300 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004-2008 - * Matrix-Vision GmbH, andre.schwarz@matrix-vision.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <version.h> - -#define CONFIG_MPC5200 1 - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFF800000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 - -#define CONFIG_MISC_INIT_R 1 - -#define CONFIG_SYS_CACHELINE_SIZE 32 -#ifdef CONFIG_CMD_KGDB -#define CONFIG_SYS_CACHELINE_SHIFT 5 -#endif - -#define CONFIG_PSC_CONSOLE 1 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200, 230400} - -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -#undef CONFIG_PCI_SCAN_SHOW -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_SYS_XLB_PIPELINING 1 -#define CONFIG_HIGH_BATS 1 - -#define MV_CI mvBlueCOUGAR-P -#define MV_VCI mvBlueCOUGAR-P -#define MV_FPGA_DATA 0xff860000 -#define MV_FPGA_SIZE 0 -#define MV_KERNEL_ADDR 0xffd00000 -#define MV_INITRD_ADDR 0xff900000 -#define MV_INITRD_LENGTH 0x00400000 -#define MV_SCRATCH_ADDR 0x00000000 -#define MV_SCRATCH_LENGTH MV_INITRD_LENGTH -#define MV_SCRIPT_ADDR 0xff840000 -#define MV_SCRIPT_ADDR2 0xff850000 -#define MV_DTB_ADDR 0xfffc0000 - -#define CONFIG_SHOW_BOOT_PROGRESS 1 - -#define MV_KERNEL_ADDR_RAM 0x00100000 -#define MV_DTB_ADDR_RAM 0x00600000 -#define MV_INITRD_ADDR_RAM 0x01000000 - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - -#define OF_CPU "PowerPC,5200@0" -#define OF_SOC "soc5200@f0000000" -#define OF_TBCLK (bd->bi_busfreq / 4) -#define MV_DTB_NAME mvbc-p.dtb -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 - -/* - * Supported commands - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_NET -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_PCI -#define CONFIG_CMD_FPGA -#define CONFIG_CMD_FPGA_LOADMK -#define CONFIG_CMD_I2C - -#undef CONFIG_WATCHDOG - -#define CONFIG_BOOTP_VENDOREX -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_NTPSERVER -#define CONFIG_BOOTP_RANDOM_DELAY -#define CONFIG_BOOTP_SEND_HOSTNAME -#define CONFIG_LIB_RAND - -/* - * Autoboot - */ -#define CONFIG_BOOTDELAY 2 -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_STOP_STR "s" -#define CONFIG_ZERO_BOOTDELAY_CHECK -#define CONFIG_RESET_TO_RETRY 1000 - -#define CONFIG_BOOTCOMMAND "if imi ${script_addr}; \ - then source ${script_addr}; \ - else source ${script_addr2}; \ - fi;" - -#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs" -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "console_nr=0\0" \ - "console=yes\0" \ - "stdin=serial\0" \ - "stdout=serial\0" \ - "stderr=serial\0" \ - "fpga=0\0" \ - "fpgadata=" __stringify(MV_FPGA_DATA) "\0" \ - "fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0" \ - "script_addr=" __stringify(MV_SCRIPT_ADDR) "\0" \ - "script_addr2=" __stringify(MV_SCRIPT_ADDR2) "\0" \ - "mv_kernel_addr=" __stringify(MV_KERNEL_ADDR) "\0" \ - "mv_kernel_addr_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0" \ - "mv_initrd_addr=" __stringify(MV_INITRD_ADDR) "\0" \ - "mv_initrd_addr_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0" \ - "mv_initrd_length=" __stringify(MV_INITRD_LENGTH) "\0" \ - "mv_dtb_addr=" __stringify(MV_DTB_ADDR) "\0" \ - "mv_dtb_addr_ram=" __stringify(MV_DTB_ADDR_RAM) "\0" \ - "dtb_name=" __stringify(MV_DTB_NAME) "\0" \ - "mv_scratch_addr=" __stringify(MV_SCRATCH_ADDR) "\0" \ - "mv_scratch_length=" __stringify(MV_SCRATCH_LENGTH) "\0" \ - "mv_version=" U_BOOT_VERSION "\0" \ - "dhcp_client_id=" __stringify(MV_CI) "\0" \ - "dhcp_vendor-class-identifier=" __stringify(MV_VCI) "\0" \ - "netretry=no\0" \ - "use_static_ipaddr=no\0" \ - "static_ipaddr=192.168.90.10\0" \ - "static_netmask=255.255.255.0\0" \ - "static_gateway=0.0.0.0\0" \ - "initrd_name=uInitrd.mvbc-p-rfs\0" \ - "zcip=no\0" \ - "netboot=yes\0" \ - "mvtest=Ff\0" \ - "tried_bootfromflash=no\0" \ - "tried_bootfromnet=no\0" \ - "use_dhcp=yes\0" \ - "gev_start=yes\0" \ - "mvbcdma_debug=0\0" \ - "mvbcia_debug=0\0" \ - "propdev_debug=0\0" \ - "gevss_debug=0\0" \ - "watchdog=1\0" \ - "sensor_cnt=1\0" \ - "" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK -#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 - -/* - * Flash configuration - */ -#undef CONFIG_FLASH_16BIT -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 -#define CONFIG_SYS_FLASH_EMPTY_INFO - -#define CONFIG_SYS_FLASH_ERASE_TOUT 50000 -#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 256 - -#define CONFIG_SYS_LOWBOOT -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_FLASH_SIZE 0x00800000 - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH -#undef CONFIG_SYS_FLASH_PROTECTION - -#define CONFIG_ENV_ADDR 0xFFFE0000 -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x10000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR+CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT 1 -#endif - -/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CONFIG_SYS_MONITOR_LEN (512 << 10) -#define CONFIG_SYS_MALLOC_LEN (512 << 10) -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_MODULE 1 -#define CONFIG_SYS_I2C_SPEED 86000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * Ethernet configuration - */ -#define CONFIG_NET_RETRY_COUNT 5 - -#define CONFIG_E1000 -#define CONFIG_E1000_FALLBACK_MAC { 0xb6, 0xb4, 0x45, 0xeb, 0xfb, 0xc0 } -#undef CONFIG_MPC5xxx_FEC -#undef CONFIG_PHY_ADDR -#define CONFIG_NETDEV eth0 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_CMDLINE_EDITING -#undef CONFIG_SYS_LONGHELP -#ifdef CONFIG_CMD_KGDB -#define CONFIG_SYS_CBSIZE 1024 -#else -#define CONFIG_SYS_CBSIZE 256 -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00800000 -#define CONFIG_SYS_MEMTEST_END 0x02f00000 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x02000000 -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 0x00200000 - -/* - * Various low-level settings - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x20000004 - -#define CONFIG_SYS_HID0_INIT (HID0_ICE | HID0_ICFI) -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00047800 -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_CS_BURST 0x000000f0 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333303 - -#define CONFIG_SYS_RESET_ADDRESS 0x00000100 - -#undef FPGA_DEBUG -#undef CONFIG_SYS_FPGA_PROG_FEEDBACK -#define CONFIG_FPGA -#define CONFIG_FPGA_ALTERA 1 -#define CONFIG_FPGA_CYCLON2 1 -#define CONFIG_FPGA_COUNT 1 - -#endif diff --git a/include/configs/MVBLM7.h b/include/configs/MVBLM7.h deleted file mode 100644 index 1ee4d7cc33..0000000000 --- a/include/configs/MVBLM7.h +++ /dev/null @@ -1,491 +0,0 @@ -/* - * Copyright (C) Matrix Vision GmbH 2008 - * - * Matrix Vision mvBlueLYNX-M7 configuration file - * based on Freescale's MPC8349ITX. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <version.h> - -/* - * High Level Configuration Options - */ -#define CONFIG_E300 1 -#define CONFIG_MPC834x 1 -#define CONFIG_MPC8343 1 - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#define CONFIG_SYS_IMMR 0xE0000000 - -#define CONFIG_PCI -#define CONFIG_PCI_INDIRECT_BRIDGE -#define CONFIG_PCI_SKIP_HOST_BRIDGE -#define CONFIG_TSEC_ENET -#define CONFIG_MPC8XXX_SPI -#define CONFIG_HARD_SPI -#define MVBLM7_MMC_CS 0x04000000 -#define CONFIG_MISC_INIT_R - -/* I2C */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_FSL -#define CONFIG_SYS_FSL_I2C_SPEED 100000 -#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 -#define CONFIG_SYS_FSL_I2C2_SPEED 100000 -#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F -#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 - -/* - * DDR Setup - */ -#undef CONFIG_SPD_EEPROM - -#define CONFIG_SYS_DDR_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE -#define CONFIG_SYS_83XX_DDR_USES_CS0 1 -#define CONFIG_SYS_MEMTEST_START (60<<20) -#define CONFIG_SYS_MEMTEST_END (70<<20) -#define CONFIG_VERY_BIG_RAM - -#define CONFIG_SYS_DDRCDR (DDRCDR_PZ_HIZ \ - | DDRCDR_NZ_HIZ \ - | DDRCDR_Q_DRN) - /* 0x22000001 */ -#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 - -#define CONFIG_SYS_DDR_SIZE 512 - -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 - -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f - -#define CONFIG_SYS_DDR_TIMING_0 0x00260802 -#define CONFIG_SYS_DDR_TIMING_1 0x3837c322 -#define CONFIG_SYS_DDR_TIMING_2 0x0f9848c6 -#define CONFIG_SYS_DDR_TIMING_3 0x00000000 - -#define CONFIG_SYS_DDR_SDRAM_CFG 0x43080008 -#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 -#define CONFIG_SYS_DDR_INTERVAL 0x02000100 - -#define CONFIG_SYS_DDR_MODE 0x04040242 -#define CONFIG_SYS_DDR_MODE2 0x00800000 - -/* Flash */ -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT - -#define CONFIG_SYS_FLASH_BASE 0xFF800000 -#define CONFIG_SYS_FLASH_SIZE 8 -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 256 - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ - | BR_PS_16 \ - | BR_MS_GPCM \ - | BR_V) -#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ - | OR_UPM_XAM \ - | OR_GPCM_CSNT \ - | OR_GPCM_ACS_DIV2 \ - | OR_GPCM_XACS \ - | OR_GPCM_SCY_15 \ - | OR_GPCM_TRLX_SET \ - | OR_GPCM_EHTR_SET \ - | OR_GPCM_EAD) -#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_8MB) - -/* - * U-Boot memory configuration - */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#undef CONFIG_SYS_RAMBOOT - -#define CONFIG_SYS_INIT_RAM_LOCK -#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ -#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ - -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CONFIG_SYS_MONITOR_LEN (512 * 1024) -#define CONFIG_SYS_MALLOC_LEN (512 * 1024) - -/* - * Local Bus LCRR and LBCR regs - * LCRR: DLL bypass, Clock divider is 4 - * External Local Bus rate is - * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV - */ -#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP -#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 -#define CONFIG_SYS_LBC_LBCR 0x00000000 - -/* LB sdram refresh timer, about 6us */ -#define CONFIG_SYS_LBC_LSRT 0x32000000 -/* LB refresh timer prescal, 266MHz/32*/ -#define CONFIG_SYS_LBC_MRTPR 0x20000000 - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE 1 -#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) - -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} - -#define CONFIG_CONSOLE ttyS0 -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) -#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 -#define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define MV_DTB_NAME "mvblm7.dtb" - -/* - * PCI - */ -#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 -#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE -#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 -#define CONFIG_SYS_PCI1_MMIO_BASE \ - (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE) -#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE -#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 -#define CONFIG_SYS_PCI1_IO_BASE 0x00000000 -#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 -#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 - -#define CONFIG_NET_RETRY_COUNT 3 - -#define CONFIG_PCI_66M -#define CONFIG_83XX_CLKIN 66666667 -#define CONFIG_PCI_PNP -#define CONFIG_PCI_SCAN_SHOW - -/* TSEC */ -#define CONFIG_GMII -#define CONFIG_SYS_VSC8601_SKEWFIX -#define CONFIG_SYS_VSC8601_SKEW_TX 3 -#define CONFIG_SYS_VSC8601_SKEW_RX 3 - -#define CONFIG_TSEC1 -#define CONFIG_TSEC2 - -#define CONFIG_HAS_ETH0 -#define CONFIG_TSEC1_NAME "TSEC0" -#define CONFIG_FEC1_PHY_NORXERR -#define CONFIG_SYS_TSEC1_OFFSET 0x24000 -#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET) -#define TSEC1_PHY_ADDR 0x10 -#define TSEC1_PHYIDX 0 -#define TSEC1_FLAGS (TSEC_GIGABIT|TSEC_REDUCED) - -#define CONFIG_HAS_ETH1 -#define CONFIG_TSEC2_NAME "TSEC1" -#define CONFIG_FEC2_PHY_NORXERR -#define CONFIG_SYS_TSEC2_OFFSET 0x25000 -#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET) -#define TSEC2_PHY_ADDR 0x11 -#define TSEC2_PHYIDX 0 -#define TSEC2_FLAGS (TSEC_GIGABIT|TSEC_REDUCED) - -#define CONFIG_ETHPRIME "TSEC0" - -#define CONFIG_BOOTP_VENDOREX -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_NTPSERVER -#define CONFIG_BOOTP_RANDOM_DELAY -#define CONFIG_BOOTP_SEND_HOSTNAME -#define CONFIG_LIB_RAND - -/* USB */ -#define CONFIG_SYS_USB_HOST -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_FSL -#define CONFIG_HAS_FSL_DR_USB -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET - -/* - * Environment - */ -#undef CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR 0xFF800000 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x2000 -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR+CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -#define CONFIG_LOADS_ECHO -#define CONFIG_SYS_LOADS_BAUD_CHANGE - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_PCI -#define CONFIG_CMD_I2C -#define CONFIG_CMD_FPGA -#define CONFIG_CMD_FPGA_LOADMK -#define CONFIG_CMD_USB -#define CONFIG_DOS_PARTITION - -#undef CONFIG_WATCHDOG - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_CMDLINE_EDITING -#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ -#define CONFIG_SYS_HUSH_PARSER - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x2000000 -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 0x200000 - -#define CONFIG_SYS_PROMPT "mvBL-M7> " -#define CONFIG_SYS_CBSIZE 256 - -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -/* - * For booting Linux, the board info and command line data - * have to be in the first 256 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ - /* Initial Memory map for Linux*/ -#define CONFIG_SYS_BOOTMAPSZ (256 << 20) - -#define CONFIG_SYS_HRCW_LOW 0x0 -#define CONFIG_SYS_HRCW_HIGH 0x0 - -/* - * System performance - */ -#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ -#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ -#define CONFIG_SYS_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */ -#define CONFIG_SYS_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */ - -/* clocking */ -#define CONFIG_SYS_SCCR_ENCCM 0 -#define CONFIG_SYS_SCCR_USBMPHCM 0 -#define CONFIG_SYS_SCCR_USBDRCM 2 -#define CONFIG_SYS_SCCR_TSEC1CM 1 -#define CONFIG_SYS_SCCR_TSEC2CM 1 - -#define CONFIG_SYS_SICRH 0x1fef0003 -#define CONFIG_SYS_SICRL (SICRL_LDP_A | SICRL_USB1 | SICRL_USB0) - -#define CONFIG_SYS_HID0_INIT 0x000000000 -#define CONFIG_SYS_HID0_FINAL (CONFIG_SYS_HID0_INIT | \ - HID0_ENABLE_INSTRUCTION_CACHE) - -#define CONFIG_SYS_HID2 HID2_HBE -#define CONFIG_HIGH_BATS 1 - -/* DDR */ -#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) - -/* PCI */ -#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE) -#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) - -/* no PCI2 */ -#define CONFIG_SYS_IBAT3L 0 -#define CONFIG_SYS_IBAT3U 0 -#define CONFIG_SYS_IBAT4L 0 -#define CONFIG_SYS_IBAT4U 0 - -/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ -#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR \ - | BATL_PP_RW \ - | BATL_CACHEINHIBIT \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) - -/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFF800000 */ -#define CONFIG_SYS_IBAT6L (0xF0000000 \ - | BATL_PP_RW \ - | BATL_MEMCOHERENCE \ - | BATL_GUARDEDSTORAGE) -#define CONFIG_SYS_IBAT6U (0xF0000000 \ - | BATU_BL_256M \ - | BATU_VS \ - | BATU_VP) -#define CONFIG_SYS_IBAT7L 0 -#define CONFIG_SYS_IBAT7U 0 - -#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L -#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U -#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L -#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U -#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L -#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U -#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L -#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U -#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L -#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U -#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L -#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U -#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L -#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U -#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L -#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U - -/* - * Environment Configuration - */ -#define CONFIG_ENV_OVERWRITE - -#define CONFIG_NETDEV eth0 - -/* Default path and filenames */ -#define CONFIG_BOOTDELAY 5 -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_STOP_STR "s" -#define CONFIG_ZERO_BOOTDELAY_CHECK -#define CONFIG_RESET_TO_RETRY 1000 - -#define MV_CI "mvBL-M7" -#define MV_VCI "mvBL-M7" -#define MV_FPGA_DATA 0xfff40000 -#define MV_FPGA_SIZE 0 -#define MV_KERNEL_ADDR 0xff810000 -#define MV_INITRD_ADDR 0xffb00000 -#define MV_SCRIPT_ADDR 0xff804000 -#define MV_SCRIPT_ADDR2 0xff806000 -#define MV_DTB_ADDR 0xff808000 -#define MV_INITRD_LENGTH 0x00400000 - -#define CONFIG_SHOW_BOOT_PROGRESS 1 - -#define MV_KERNEL_ADDR_RAM 0x00100000 -#define MV_DTB_ADDR_RAM 0x00600000 -#define MV_INITRD_ADDR_RAM 0x01000000 - -#define CONFIG_BOOTCOMMAND "if imi ${script_addr}; " \ - "then source ${script_addr}; " \ - "else source ${script_addr2}; " \ - "fi;" -#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "console_nr=0\0" \ - "baudrate=" __stringify(CONFIG_BAUDRATE) "\0" \ - "stdin=serial\0" \ - "stdout=serial\0" \ - "stderr=serial\0" \ - "fpga=0\0" \ - "fpgadata=" __stringify(MV_FPGA_DATA) "\0" \ - "fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0" \ - "script_addr=" __stringify(MV_SCRIPT_ADDR) "\0" \ - "script_addr2=" __stringify(MV_SCRIPT_ADDR2) "\0" \ - "mv_kernel_addr=" __stringify(MV_KERNEL_ADDR) "\0" \ - "mv_kernel_addr_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0" \ - "mv_initrd_addr=" __stringify(MV_INITRD_ADDR) "\0" \ - "mv_initrd_addr_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0" \ - "mv_initrd_length=" __stringify(MV_INITRD_LENGTH) "\0" \ - "mv_dtb_addr=" __stringify(MV_DTB_ADDR) "\0" \ - "mv_dtb_addr_ram=" __stringify(MV_DTB_ADDR_RAM) "\0" \ - "dtb_name=" __stringify(MV_DTB_NAME) "\0" \ - "mv_version=" U_BOOT_VERSION "\0" \ - "dhcp_client_id=" MV_CI "\0" \ - "dhcp_vendor-class-identifier=" MV_VCI "\0" \ - "netretry=no\0" \ - "use_static_ipaddr=no\0" \ - "static_ipaddr=192.168.90.10\0" \ - "static_netmask=255.255.255.0\0" \ - "static_gateway=0.0.0.0\0" \ - "initrd_name=uInitrd.mvBL-M7-rfs\0" \ - "zcip=no\0" \ - "netboot=yes\0" \ - "mvtest=Ff\0" \ - "tried_bootfromflash=no\0" \ - "tried_bootfromnet=no\0" \ - "bootfile=mvblm72625.boot\0" \ - "use_dhcp=yes\0" \ - "gev_start=yes\0" \ - "mvbcdma_debug=0\0" \ - "mvbcia_debug=0\0" \ - "propdev_debug=0\0" \ - "gevss_debug=0\0" \ - "watchdog=0\0" \ - "usb_dr_mode=host\0" \ - "sensor_cnt=2\0" \ - "" - -#define CONFIG_FPGA_COUNT 1 -#define CONFIG_FPGA -#define CONFIG_FPGA_ALTERA -#define CONFIG_FPGA_CYCLON2 - -#endif diff --git a/include/configs/MVSMR.h b/include/configs/MVSMR.h deleted file mode 100644 index 27f730d84b..0000000000 --- a/include/configs/MVSMR.h +++ /dev/null @@ -1,270 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * (C) Copyright 2004-2010 - * Matrix-Vision GmbH, andre.schwarz@matrix-vision.de - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include <version.h> - -#define CONFIG_MPC5200 1 - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFF800000 -#endif -#define CONFIG_SYS_LDSCRIPT "board/matrix_vision/mvsmr/u-boot.lds" - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 - -#define CONFIG_MISC_INIT_R 1 - -#define CONFIG_SYS_CACHELINE_SIZE 32 -#ifdef CONFIG_CMD_KGDB -#define CONFIG_SYS_CACHELINE_SHIFT 5 -#endif - -#define CONFIG_PSC_CONSOLE 1 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200,\ - 230400} - -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -#undef CONFIG_PCI_SCAN_SHOW -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_SYS_XLB_PIPELINING 1 -#define CONFIG_HIGH_BATS 1 - -#define MV_CI mvSMR -#define MV_VCI mvSMR -#define MV_FPGA_DATA 0xff840000 -#define MV_FPGA_SIZE 0x1ff88 -#define MV_KERNEL_ADDR 0xfff00000 -#define MV_SCRIPT_ADDR 0xff806000 -#define MV_INITRD_ADDR 0xff880000 -#define MV_INITRD_LENGTH 0x00240000 -#define MV_SCRATCH_ADDR 0xffcc0000 -#define MV_SCRATCH_LENGTH MV_INITRD_LENGTH - -#define CONFIG_SHOW_BOOT_PROGRESS 1 - -#define MV_KERNEL_ADDR_RAM 0x00100000 -#define MV_INITRD_ADDR_RAM 0x00400000 - -/* - * Supported commands - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_FPGA -#define CONFIG_CMD_FPGA_LOADMK -#define CONFIG_CMD_I2C -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_SDRAM - -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_NTPSERVER -#define CONFIG_BOOTP_RANDOM_DELAY -#define CONFIG_BOOTP_SEND_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_VENDOREX -#define CONFIG_LIB_RAND - -/* - * Autoboot - */ -#define CONFIG_BOOTDELAY 1 -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_STOP_STR "abcdefg" -#define CONFIG_ZERO_BOOTDELAY_CHECK - -#define CONFIG_BOOTCOMMAND "source ${script_addr}" -#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs" \ - " allocate=6M" - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "console_nr=0\0" \ - "console=no\0" \ - "stdin=serial\0" \ - "stdout=serial\0" \ - "stderr=serial\0" \ - "fpga=0\0" \ - "fpgadata=" __stringify(MV_FPGA_DATA) "\0" \ - "fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0" \ - "mv_kernel_addr=" __stringify(MV_KERNEL_ADDR) "\0" \ - "mv_kernel_addr_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0" \ - "script_addr=" __stringify(MV_SCRIPT_ADDR) "\0" \ - "mv_initrd_addr=" __stringify(MV_INITRD_ADDR) "\0" \ - "mv_initrd_addr_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0" \ - "mv_initrd_length=" __stringify(MV_INITRD_LENGTH) "\0" \ - "mv_scratch_addr=" __stringify(MV_SCRATCH_ADDR) "\0" \ - "mv_scratch_length=" __stringify(MV_SCRATCH_LENGTH) "\0" \ - "mv_version=" U_BOOT_VERSION "\0" \ - "dhcp_client_id=" __stringify(MV_CI) "\0" \ - "dhcp_vendor-class-identifier=" __stringify(MV_VCI) "\0" \ - "netretry=no\0" \ - "use_static_ipaddr=no\0" \ - "static_ipaddr=192.168.0.101\0" \ - "static_netmask=255.255.255.0\0" \ - "static_gateway=0.0.0.0\0" \ - "initrd_name=uInitrd.mvsmr-rfs\0" \ - "zcip=yes\0" \ - "netboot=no\0" \ - "" - -/* - * IPB Bus clocking configuration. - */ -#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK - -/* - * Flash configuration - */ -#undef CONFIG_FLASH_16BIT -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 -#define CONFIG_SYS_FLASH_EMPTY_INFO - -#define CONFIG_SYS_FLASH_ERASE_TOUT 50000 -#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -#define CONFIG_SYS_MAX_FLASH_SECT 256 - -#define CONFIG_SYS_LOWBOOT -#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_FLASH_SIZE 0x00800000 - -/* - * Environment settings - */ -#define CONFIG_ENV_IS_IN_FLASH -#undef CONFIG_SYS_FLASH_PROTECTION -#define CONFIG_OVERWRITE_ETHADDR_ONCE - -#define CONFIG_ENV_OFFSET 0x8000 -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x2000 - -/* used by linker script to wrap code around */ -#define CONFIG_SCRIPT_OFFSET 0x6000 -#define CONFIG_SCRIPT_SECT_SIZE 0x2000 - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT 1 -#endif - -/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */ -#define CONFIG_SYS_MONITOR_LEN (512 << 10) -#define CONFIG_SYS_MALLOC_LEN (512 << 10) -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) - -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 -#define CONFIG_SYS_I2C_MODULE 1 -#define CONFIG_SYS_I2C_SPEED 86000 -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * Ethernet configuration - */ -#define CONFIG_NET_RETRY_COUNT 5 - -#define CONFIG_MPC5xxx_FEC -#define CONFIG_MPC5xxx_FEC_MII100 -#define CONFIG_PHY_ADDR 0x00 -#define CONFIG_NETDEV eth0 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_CMDLINE_EDITING -#undef CONFIG_SYS_LONGHELP -#ifdef CONFIG_CMD_KGDB -#define CONFIG_SYS_CBSIZE 1024 -#else -#define CONFIG_SYS_CBSIZE 256 -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x00800000 -#define CONFIG_SYS_MEMTEST_END 0x02f00000 - -/* default load address */ -#define CONFIG_SYS_LOAD_ADDR 0x02000000 -/* default location for tftp and bootm */ -#define CONFIG_LOADADDR 0x00200000 - -/* - * Various low-level settings - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x00050044 - -#define CONFIG_SYS_HID0_INIT (HID0_ICE | HID0_ICFI) -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x00047800 -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_CS_BURST 0x000000f0 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333303 - -#define CONFIG_SYS_RESET_ADDRESS 0x00000100 - -#undef FPGA_DEBUG -#undef CONFIG_SYS_FPGA_PROG_FEEDBACK -#define CONFIG_FPGA -#define CONFIG_FPGA_XILINX 1 -#define CONFIG_FPGA_SPARTAN2 1 -#define CONFIG_FPGA_COUNT 1 - -#endif diff --git a/include/configs/PATI.h b/include/configs/PATI.h index d823b0f3cc..3ca204e1e2 100644 --- a/include/configs/PATI.h +++ b/include/configs/PATI.h @@ -21,6 +21,8 @@ #define CONFIG_SYS_TEXT_BASE 0xFFF00000 +#define CONFIG_SYS_GENERIC_BOARD + /* Serial Console Configuration */ #define CONFIG_5xx_CONS_SCI1 #undef CONFIG_5xx_CONS_SCI2 @@ -96,6 +98,7 @@ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 1250000 } +#define CONFIG_BOARD_EARLY_INIT_F /*********************************************************************** * Last Stage Init diff --git a/include/configs/PIP405.h b/include/configs/PIP405.h index a6f505aaa9..9a1b2acac3 100644 --- a/include/configs/PIP405.h +++ b/include/configs/PIP405.h @@ -21,6 +21,8 @@ #define CONFIG_SYS_TEXT_BASE 0xFFF80000 +#define CONFIG_SYS_GENERIC_BOARD + /*********************************************************** * Clock ***********************************************************/ diff --git a/include/configs/VCMA9.h b/include/configs/VCMA9.h index d40185e1e2..a97f5faae4 100644 --- a/include/configs/VCMA9.h +++ b/include/configs/VCMA9.h @@ -28,6 +28,8 @@ #define CONFIG_SYS_TEXT_BASE 0x0 +#define CONFIG_SYS_GENERIC_BOARD + #define CONFIG_SYS_ARM_CACHE_WRITETHROUGH /* input clock of PLL (VCMA9 has 12MHz input clock) */ @@ -214,7 +216,6 @@ /* File system */ #define CONFIG_CMD_FAT -#define CONFIG_CMD_EXT2 #define CONFIG_CMD_UBI #define CONFIG_CMD_UBIFS #define CONFIG_CMD_JFFS2 diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index e2f7ead9bc..476430ddd0 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -223,6 +223,7 @@ /* Bootcount using the RTC block */ #define CONFIG_BOOTCOUNT_LIMIT #define CONFIG_BOOTCOUNT_AM33XX +#define CONFIG_SYS_BOOTCOUNT_BE /* USB gadget RNDIS */ #define CONFIG_SPL_MUSB_NEW_SUPPORT diff --git a/include/configs/axs101.h b/include/configs/axs101.h index c22d6d0c75..1bf8390722 100644 --- a/include/configs/axs101.h +++ b/include/configs/axs101.h @@ -125,7 +125,6 @@ */ #define CONFIG_DESIGNWARE_ETH #define CONFIG_DW_AUTONEG -#define CONFIG_DW_SEARCH_PHY #define CONFIG_NET_MULTI /* diff --git a/include/configs/bluestone.h b/include/configs/bluestone.h deleted file mode 100644 index 8bd71c6a15..0000000000 --- a/include/configs/bluestone.h +++ /dev/null @@ -1,168 +0,0 @@ -/* - * bluestone.h - configuration for Bluestone (APM821XX) - * - * Copyright (c) 2010, Applied Micro Circuits Corporation - * Author: Tirumala R Marri <tmarri@apm.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ -#define CONFIG_APM821XX 1 /* APM821XX series */ -#define CONFIG_HOSTNAME bluestone - -#define CONFIG_440 1 - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFFA0000 -#endif - -/* - * Include common defines/options for all AMCC eval boards - */ -#include "amcc-common.h" -#define CONFIG_SYS_CLK_FREQ 50000000 - -#define CONFIG_BOARD_TYPES 1 /* support board types */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -/* EBC stuff */ -/* later mapped to this addr */ -#define CONFIG_SYS_FLASH_BASE 0xFFF00000 -#define CONFIG_SYS_FLASH_SIZE (4 << 20) /* 1MB usable */ - -/* EBC Boot Space: 0xFF000000 */ -#define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 -#define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 32k */ -#define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */ -#define CONFIG_SYS_AHB_BASE 0xE2000000 /* internal AHB peripherals*/ - -#define CONFIG_SYS_SRAM_SIZE (256 << 10) -/* - * Initial RAM & stack pointer (placed in OCM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ -#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) -#define CONFIG_SYS_GBL_DATA_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* - * Environment - */ -/* - * Define here the location of the environment variables (FLASH). - */ -#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ - -/* - * FLASH related - */ -#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ -#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} -/* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 -/* max number of sectors on one chip */ -#define CONFIG_SYS_MAX_FLASH_SECT 80 -/* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 -/* Timeout for Flash Write (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 -/* use buffered writes (20x faster) */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 -/* print 'E' for empty sector on flinfo */ -#define CONFIG_SYS_FLASH_EMPTY_INFO -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) -#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) -#endif /* CONFIG_ENV_IS_IN_FLASH */ - -/* SDRAM */ -#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */ -#define SPD_EEPROM_ADDRESS {0x53, 0x51} /* SPD i2c spd addresses */ -#define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */ -#define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */ -#define CONFIG_DDR_ECC 1 /* with ECC support */ - -/* - * Serial Port - */ -#define CONFIG_CONS_INDEX 1 /* Use UART0 */ - -/* - * I2C - */ -#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 -#define CONFIG_SYS_I2C_MULTI_EEPROMS -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 /* Data sheet */ - -/* I2C bootstrap EEPROM */ -#define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x52 -#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 -#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 - -/* - * Ethernet - */ -#define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_EMAC_PHY_MODE EMAC_PHY_MODE_NONE_RGMII -#define CONFIG_HAS_ETH0 -/* PHY address, See schematics */ -#define CONFIG_PHY_ADDR 0x1f -/* reset phy upon startup */ -#define CONFIG_PHY_RESET 1 -/* Include GbE speed/duplex detection */ -#define CONFIG_PHY_GIGE 1 -#define CONFIG_PHY_DYNAMIC_ANEG 1 - -/* - * External Bus Controller (EBC) Setup - **/ -#define CONFIG_SYS_EBC_CFG (EBC_CFG_LE_LOCK | \ - EBC_CFG_PTD_ENABLE | \ - EBC_CFG_RTC_2048PERCLK | \ - EBC_CFG_ATC_HI | \ - EBC_CFG_DTC_HI | \ - EBC_CFG_CTC_HI | \ - EBC_CFG_OEO_PREVIOUS) -/* NOR Flash */ -#define CONFIG_SYS_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \ - EBC_BXAP_TWT_ENCODE(64) | \ - EBC_BXAP_BCE_DISABLE | \ - EBC_BXAP_BCT_2TRANS | \ - EBC_BXAP_CSN_ENCODE(1) | \ - EBC_BXAP_OEN_ENCODE(2) | \ - EBC_BXAP_WBN_ENCODE(2) | \ - EBC_BXAP_WBF_ENCODE(2) | \ - EBC_BXAP_TH_ENCODE(7) | \ - EBC_BXAP_SOR_DELAYED | \ - EBC_BXAP_BEM_WRITEONLY | \ - EBC_BXAP_PEN_DISABLED) -/* Peripheral Bank Configuration Register - EBC_BxCR */ -#define CONFIG_SYS_EBC_PB0CR \ - (EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) | \ - EBC_BXCR_BS_1MB | \ - EBC_BXCR_BU_RW | \ - EBC_BXCR_BW_8BIT) - - -#endif /* __CONFIG_H */ diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h index e66f30655d..b17e495f5f 100644 --- a/include/configs/omap3_overo.h +++ b/include/configs/omap3_overo.h @@ -151,7 +151,7 @@ "run mmcboot;" \ "fi;" \ "if run loadzimage; then " \ - "if test $fdtfile; then " \ + "if test -z \"${fdtfile}\"; then " \ "setenv fdtfile omap3-${boardname}-${expansionname}.dtb;" \ "fi;" \ "if run loadfdt; then " \ diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h index 7e2ecd53f5..e8dc462f14 100644 --- a/include/configs/omap5_uevm.h +++ b/include/configs/omap5_uevm.h @@ -72,7 +72,6 @@ /* Max time to hold reset on this board, see doc/README.omap-reset-time */ #define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296 -#define CONFIG_BOARD_LATE_INIT #define CONFIG_CMD_SCSI #define CONFIG_LIBATA #define CONFIG_SCSI_AHCI diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h index bf9752f874..1ce0965912 100644 --- a/include/configs/siemens-am33x-common.h +++ b/include/configs/siemens-am33x-common.h @@ -231,7 +231,7 @@ #define CONFIG_MUSB_GADGET #define CONFIG_MUSB_PIO_ONLY #define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT -#define CONFIG_USB_GADGET_DUALSPEED +#undef CONFIG_USB_GADGET_DUALSPEED #define CONFIG_USB_GADGET_VBUS_DRAW 2 #define CONFIG_MUSB_HOST diff --git a/include/configs/socfpga_common.h b/include/configs/socfpga_common.h new file mode 100644 index 0000000000..49504dcafb --- /dev/null +++ b/include/configs/socfpga_common.h @@ -0,0 +1,196 @@ +/* + * Copyright (C) 2012 Altera Corporation <www.altera.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#ifndef __CONFIG_SOCFPGA_CYCLONE5_COMMON_H__ +#define __CONFIG_SOCFPGA_CYCLONE5_COMMON_H__ + +#define CONFIG_SYS_GENERIC_BOARD + +/* Virtual target or real hardware */ +#undef CONFIG_SOCFPGA_VIRTUAL_TARGET + +#define CONFIG_ARMV7 +#define CONFIG_SYS_THUMB_BUILD + +#define CONFIG_SOCFPGA + +/* + * High level configuration + */ +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_MISC_INIT_R +#define CONFIG_SYS_NO_FLASH +#define CONFIG_CLOCKS + +#define CONFIG_FIT +#define CONFIG_OF_LIBFDT +#define CONFIG_SYS_BOOTMAPSZ (64 * 1024 * 1024) + +#define CONFIG_TIMESTAMP /* Print image info with timestamp */ + +/* + * Memory configurations + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM_1 0x0 +#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) +#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1 +#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE + +#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000 +#define CONFIG_SYS_INIT_RAM_SIZE (0x10000 - 0x100) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define CONFIG_SYS_TEXT_BASE 0x08000040 +#else +#define CONFIG_SYS_TEXT_BASE 0x01000040 +#endif + +/* + * U-Boot general configurations + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + /* Print buffer size */ +#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + /* Boot argument buffer size */ +#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ +#define CONFIG_AUTO_COMPLETE /* Command auto complete */ +#define CONFIG_CMDLINE_EDITING /* Command history etc */ +#define CONFIG_SYS_HUSH_PARSER + +/* + * Cache + */ +#define CONFIG_SYS_ARM_CACHE_WRITEALLOC +#define CONFIG_SYS_CACHELINE_SIZE 32 +#define CONFIG_SYS_L2_PL310 +#define CONFIG_SYS_PL310_BASE SOCFPGA_MPUL2_ADDRESS + +/* + * Ethernet on SoC (EMAC) + */ +#if defined(CONFIG_CMD_NET) && !defined(CONFIG_SOCFPGA_VIRTUAL_TARGET) +#define CONFIG_DESIGNWARE_ETH +#define CONFIG_NET_MULTI +#define CONFIG_DW_ALTDESCRIPTOR +#define CONFIG_MII +#define CONFIG_AUTONEG_TIMEOUT (15 * CONFIG_SYS_HZ) +#define CONFIG_PHYLIB +#define CONFIG_PHY_GIGE +#endif + +/* + * FPGA Driver + */ +#ifdef CONFIG_CMD_FPGA +#define CONFIG_FPGA +#define CONFIG_FPGA_ALTERA +#define CONFIG_FPGA_SOCFPGA +#define CONFIG_FPGA_COUNT 1 +#endif + +/* + * L4 OSC1 Timer 0 + */ +/* This timer uses eosc1, whose clock frequency is fixed at any condition. */ +#define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS +#define CONFIG_SYS_TIMER_COUNTS_DOWN +#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4) +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define CONFIG_SYS_TIMER_RATE 2400000 +#else +#define CONFIG_SYS_TIMER_RATE 25000000 +#endif + +/* + * L4 Watchdog + */ +#ifdef CONFIG_HW_WATCHDOG +#define CONFIG_DESIGNWARE_WATCHDOG +#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS +#define CONFIG_DW_WDT_CLOCK_KHZ 25000 +#define CONFIG_HW_WATCHDOG_TIMEOUT_MS 12000 +#endif + +/* + * MMC Driver + */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_BOUNCE_BUFFER +#define CONFIG_GENERIC_MMC +#define CONFIG_DWMMC +#define CONFIG_SOCFPGA_DWMMC +#define CONFIG_SOCFPGA_DWMMC_FIFO_DEPTH 1024 +#define CONFIG_SOCFPGA_DWMMC_DRVSEL 3 +#define CONFIG_SOCFPGA_DWMMC_SMPSEL 0 +/* FIXME */ +/* using smaller max blk cnt to avoid flooding the limited stack we have */ +#define CONFIG_SYS_MMC_MAX_BLK_COUNT 256 /* FIXME -- SPL only? */ +#endif + +/* + * Serial Driver + */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE -4 +#define CONFIG_SYS_NS16550_COM1 SOCFPGA_UART0_ADDRESS +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define CONFIG_SYS_NS16550_CLK 1000000 +#else +#define CONFIG_SYS_NS16550_CLK 100000000 +#endif +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 + +/* + * U-Boot environment + */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE +#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE +#define CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_SIZE 4096 + +/* + * SPL + */ +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_RAM_DEVICE +#define CONFIG_SPL_TEXT_BASE 0xFFFF0000 +#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR +#define CONFIG_SPL_STACK_SIZE (4 * 1024) +#define CONFIG_SPL_MALLOC_SIZE (5 * 1024) /* FIXME */ +#define CONFIG_SYS_SPL_MALLOC_START ((unsigned long) (&__malloc_start)) +#define CONFIG_SYS_SPL_MALLOC_SIZE (&__malloc_end - &__malloc_start) + +#define CHUNKSZ_CRC32 (1 * 1024) /* FIXME: ewww */ +#define CONFIG_CRC32_VERIFY + +/* Linker script for SPL */ +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/socfpga/u-boot-spl.lds" + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_WATCHDOG_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT + +#ifdef CONFIG_SPL_BUILD +#undef CONFIG_PARTITIONS +#endif + +#endif /* __CONFIG_SOCFPGA_CYCLONE5_COMMON_H__ */ diff --git a/include/configs/socfpga_cyclone5.h b/include/configs/socfpga_cyclone5.h index 5d145cd821..8d54bf892d 100644 --- a/include/configs/socfpga_cyclone5.h +++ b/include/configs/socfpga_cyclone5.h @@ -1,287 +1,100 @@ /* - * Copyright (C) 2012 Altera Corporation <www.altera.com> + * Copyright (C) 2014 Marek Vasut <marex@denx.de> * * SPDX-License-Identifier: GPL-2.0+ */ -#ifndef __CONFIG_H -#define __CONFIG_H +#ifndef __CONFIG_SOCFPGA_CYCLONE5_H__ +#define __CONFIG_SOCFPGA_CYCLONE5_H__ #include <asm/arch/socfpga_base_addrs.h> #include "../../board/altera/socfpga/pinmux_config.h" #include "../../board/altera/socfpga/iocsr_config.h" #include "../../board/altera/socfpga/pll_config.h" -/* - * High level configuration - */ -/* Virtual target or real hardware */ -#undef CONFIG_SOCFPGA_VIRTUAL_TARGET - -#define CONFIG_ARMV7 -#define CONFIG_SYS_DCACHE_OFF -#undef CONFIG_USE_IRQ - -#define CONFIG_MISC_INIT_R -#define CONFIG_SINGLE_BOOTLOADER -#define CONFIG_SOCFPGA - -/* base address for .text section */ -#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET -#define CONFIG_SYS_TEXT_BASE 0x08000040 -#else -#define CONFIG_SYS_TEXT_BASE 0x01000040 -#endif -#define CONFIG_SYS_LOAD_ADDR 0x7fc0 - -/* Console I/O Buffer Size */ -#define CONFIG_SYS_CBSIZE 256 -/* Monitor Command Prompt */ -#define CONFIG_SYS_PROMPT "SOCFPGA_CYCLONE5 # " -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) - -/* - * Display CPU and Board Info - */ -#define CONFIG_DISPLAY_CPUINFO -#define CONFIG_DISPLAY_BOARDINFO - -/* - * Enable early stage initialization at C environment - */ -#define CONFIG_BOARD_EARLY_INIT_F - -/* flat device tree */ -#define CONFIG_OF_LIBFDT -/* skip updating the FDT blob */ -#define CONFIG_FDT_BLOB_SKIP_UPDATE -/* Initial Memory map size for Linux, minus 4k alignment for DFT blob */ -#define CONFIG_SYS_BOOTMAPSZ ((256*1024*1024) - (4*1024)) - -#define CONFIG_SPL_RAM_DEVICE -#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR -#define CONFIG_SYS_SPL_MALLOC_START ((unsigned long) (&__malloc_start)) -#define CONFIG_SYS_SPL_MALLOC_SIZE (&__malloc_end - &__malloc_start) - -/* - * Memory allocation (MALLOC) - */ -/* Room required on the stack for the environment data */ -#define CONFIG_ENV_SIZE 1024 -/* Size of DRAM reserved for malloc() use */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* SP location before relocation, must use scratch RAM */ -#define CONFIG_SYS_INIT_RAM_ADDR 0xFFFF0000 -/* Reserving 0x100 space at back of scratch RAM for debug info */ -#define CONFIG_SYS_INIT_RAM_SIZE (0x10000 - 0x100) -/* Stack pointer prior relocation, must situated at on-chip RAM */ -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - - -/* - * Command line configuration. - */ +/* U-Boot Commands */ #define CONFIG_SYS_NO_FLASH #include <config_cmd_default.h> -/* FAT file system support */ +#define CONFIG_DOS_PARTITION +#define CONFIG_FAT_WRITE +#define CONFIG_HW_WATCHDOG + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_BOOTZ +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_EXT4_WRITE #define CONFIG_CMD_FAT +#define CONFIG_CMD_FPGA +#define CONFIG_CMD_FS_GENERIC +#define CONFIG_CMD_GREPENV +#define CONFIG_CMD_MII +#define CONFIG_CMD_MMC +#define CONFIG_CMD_NET +#define CONFIG_CMD_PING +#define CONFIG_CMD_SETEXPR +#define CONFIG_REGEX /* Enable regular expression support */ -/* - * Misc - */ -#define CONFIG_DOS_PARTITION 1 +/* Memory configurations */ +#define PHYS_SDRAM_1_SIZE 0x40000000 /* 1GiB on SoCDK */ -#ifdef CONFIG_SPL_BUILD -#undef CONFIG_PARTITIONS +/* Booting Linux */ +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTFILE "zImage" +#define CONFIG_BOOTARGS "console=ttyS0" __stringify(CONFIG_BAUDRATE) +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define CONFIG_BOOTCOMMAND "run ramboot" +#else +#define CONFIG_BOOTCOMMAND "run mmcload; run mmcboot" #endif +#define CONFIG_LOADADDR 0x8000 +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* - * Environment setup - */ +/* Ethernet on SoC (EMAC) */ +#if defined(CONFIG_CMD_NET) +#define CONFIG_EMAC_BASE SOCFPGA_EMAC0_ADDRESS +#define CONFIG_PHY_INTERFACE_MODE PHY_INTERFACE_MODE_RGMII +#define CONFIG_EPHY0_PHY_ADDR 0 -/* Delay before automatically booting the default image */ -#define CONFIG_BOOTDELAY 3 -/* Enable auto completion of commands using TAB */ -#define CONFIG_AUTO_COMPLETE -/* use "hush" command parser */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_CMD_RUN +/* PHY */ +#define CONFIG_EPHY1_PHY_ADDR 4 +#define CONFIG_PHY_MICREL +#define CONFIG_PHY_MICREL_KSZ9021 +#define CONFIG_KSZ9021_CLK_SKEW_ENV "micrel-ksz9021-clk-skew" +#define CONFIG_KSZ9021_CLK_SKEW_VAL 0xf0f0 +#define CONFIG_KSZ9021_DATA_SKEW_ENV "micrel-ksz9021-data-skew" +#define CONFIG_KSZ9021_DATA_SKEW_VAL 0x0 -#define CONFIG_BOOTCOMMAND "run ramboot" +#endif -/* - * arguments passed to the bootm command. The value of - * CONFIG_BOOTARGS goes into the environment value "bootargs". - * Do note the value will overide also the chosen node in FDT blob. - */ -#define CONFIG_BOOTARGS "console=ttyS0,57600,mem=256M@0x0" +/* Extra Environment */ +#define CONFIG_HOSTNAME socfpga_cyclone5 #define CONFIG_EXTRA_ENV_SETTINGS \ "verify=n\0" \ "loadaddr= " __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \ "ramboot=setenv bootargs " CONFIG_BOOTARGS ";" \ "bootm ${loadaddr} - ${fdt_addr}\0" \ - "bootimage=uImage\0" \ + "bootimage=zImage\0" \ "fdt_addr=100\0" \ - "fsloadcmd=ext2load\0" \ - "bootm ${loadaddr} - ${fdt_addr}\0" \ + "fdtimage=socfpga.dtb\0" \ + "fsloadcmd=ext2load\0" \ + "bootm ${loadaddr} - ${fdt_addr}\0" \ + "mmcroot=/dev/mmcblk0p2\0" \ + "mmcboot=setenv bootargs " CONFIG_BOOTARGS \ + " root=${mmcroot} rw rootwait;" \ + "bootz ${loadaddr} - ${fdt_addr}\0" \ + "mmcload=mmc rescan;" \ + "load mmc 0:1 ${loadaddr} ${bootimage};" \ + "load mmc 0:1 ${fdt_addr} ${fdtimage}\0" \ "qspiroot=/dev/mtdblock0\0" \ "qspirootfstype=jffs2\0" \ "qspiboot=setenv bootargs " CONFIG_BOOTARGS \ " root=${qspiroot} rw rootfstype=${qspirootfstype};"\ "bootm ${loadaddr} - ${fdt_addr}\0" -/* using environment setting for stdin, stdout, stderr */ -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -/* Enable the call to overwrite_console() */ -#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE -/* Enable overwrite of previous console environment settings */ -#define CONFIG_SYS_CONSOLE_ENV_OVERWRITE - -/* max number of command args */ -#define CONFIG_SYS_MAXARGS 16 - - -/* - * Hardware drivers - */ - -/* - * SDRAM Memory Map - */ -/* We have 1 bank of DRAM */ -#define CONFIG_NR_DRAM_BANKS 1 -/* SDRAM Bank #1 */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -/* SDRAM memory size */ -#define PHYS_SDRAM_1_SIZE 0x40000000 - -#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE -#define CONFIG_SYS_MEMTEST_START 0x00000000 -#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE - -/* - * NS16550 Configuration - */ -#define UART0_BASE SOCFPGA_UART0_ADDRESS -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE -4 -#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SYS_NS16550_COM1 UART0_BASE -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200} -#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET -#define V_NS16550_CLK 1000000 -#else -#define V_NS16550_CLK 100000000 -#endif -#define CONFIG_BAUDRATE 115200 - -/* - * FLASH - */ -#define CONFIG_SYS_NO_FLASH - -/* - * L4 OSC1 Timer 0 - */ -/* This timer use eosc1 where the clock frequency is fixed - * throughout any condition */ -#define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS -/* reload value when timer count to zero */ -#define TIMER_LOAD_VAL 0xFFFFFFFF -/* Timer info */ -#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET -#define CONFIG_SYS_TIMER_RATE 2400000 -#else -#define CONFIG_SYS_TIMER_RATE 25000000 -#endif -#define CONFIG_SYS_TIMER_COUNTS_DOWN -#define CONFIG_SYS_TIMER_COUNTER (CONFIG_SYS_TIMERBASE + 0x4) - -#define CONFIG_ENV_IS_NOWHERE - -/* - * network support - */ -#ifndef CONFIG_SOCFPGA_VIRTUAL_TARGET -#define CONFIG_DESIGNWARE_ETH 1 -#endif - -#ifdef CONFIG_DESIGNWARE_ETH -#define CONFIG_EMAC0_BASE SOCFPGA_EMAC0_ADDRESS -#define CONFIG_EMAC1_BASE SOCFPGA_EMAC1_ADDRESS -/* console support for network */ -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_PING -/* designware */ -#define CONFIG_NET_MULTI -#define CONFIG_DW_ALTDESCRIPTOR -#define CONFIG_DW_SEARCH_PHY -#define CONFIG_MII -#define CONFIG_PHY_GIGE -#define CONFIG_DW_AUTONEG -#define CONFIG_AUTONEG_TIMEOUT (15 * CONFIG_SYS_HZ) -#define CONFIG_PHYLIB -#define CONFIG_PHY_MICREL -#define CONFIG_PHY_MICREL_KSZ9021 -/* EMAC controller and PHY used */ -#define CONFIG_EMAC_BASE CONFIG_EMAC1_BASE -#define CONFIG_EPHY_PHY_ADDR CONFIG_EPHY1_PHY_ADDR -#define CONFIG_PHY_INTERFACE_MODE PHY_INTERFACE_MODE_RGMII -#endif /* CONFIG_DESIGNWARE_ETH */ - -/* - * L4 Watchdog - */ -#define CONFIG_HW_WATCHDOG -#define CONFIG_HW_WATCHDOG_TIMEOUT_MS 2000 -#define CONFIG_DESIGNWARE_WATCHDOG -#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS -/* Clocks source frequency to watchdog timer */ -#define CONFIG_DW_WDT_CLOCK_KHZ 25000 - - -/* - * SPL "Second Program Loader" aka Initial Software - */ - -/* Enable building of SPL globally */ -#define CONFIG_SPL_FRAMEWORK - -/* TEXT_BASE for linking the SPL binary */ -#define CONFIG_SPL_TEXT_BASE 0xFFFF0000 - -/* Stack size for SPL */ -#define CONFIG_SPL_STACK_SIZE (4 * 1024) - -/* MALLOC size for SPL */ -#define CONFIG_SPL_MALLOC_SIZE (5 * 1024) - -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_BOARD_INIT - -#define CHUNKSZ_CRC32 (1 * 1024) - -#define CONFIG_CRC32_VERIFY - -/* Linker script for SPL */ -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/socfpga/u-boot-spl.lds" - -/* Support for common/libcommon.o in SPL binary */ -#define CONFIG_SPL_LIBCOMMON_SUPPORT -/* Support for lib/libgeneric.o in SPL binary */ -#define CONFIG_SPL_LIBGENERIC_SUPPORT - -/* Support for watchdog */ -#define CONFIG_SPL_WATCHDOG_SUPPORT +/* The rest of the configuration is shared */ +#include <configs/socfpga_common.h> -#endif /* __CONFIG_H */ +#endif /* __CONFIG_SOCFPGA_CYCLONE5_H__ */ |