diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/cmi_mpc5xx.h | 240 |
1 files changed, 0 insertions, 240 deletions
diff --git a/include/configs/cmi_mpc5xx.h b/include/configs/cmi_mpc5xx.h deleted file mode 100644 index d081865749..0000000000 --- a/include/configs/cmi_mpc5xx.h +++ /dev/null @@ -1,240 +0,0 @@ -/* - * (C) Copyright 2003 - * Martin Winistoerfer, martinwinistoerfer@gmx.ch. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * File: cmi_mpc5xx.h - * - * Discription: Config header file for cmi - * board using an MPC5xx CPU - * - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - */ - -#define CONFIG_MPC555 1 /* This is an MPC555 CPU */ -#define CONFIG_CMI 1 /* Using the customized cmi board */ - -#define CONFIG_SYS_TEXT_BASE 0x02000000 /* Boot from flash at location 0x00000000 */ - -/* Serial Console Configuration */ -#define CONFIG_5xx_CONS_SCI1 -#undef CONFIG_5xx_CONS_SCI2 - -#define CONFIG_BAUDRATE 57600 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_ASKENV - - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif -#define CONFIG_BOOTCOMMAND "go 02034004" /* autoboot command */ - -#define CONFIG_BOOTARGS "" /* Assuming OS Image in 4 flash sector at offset 4004 */ - -#define CONFIG_WATCHDOG /* turn on platform specific watchdog */ - -#define CONFIG_STATUS_LED 1 /* Enable status led */ - -#define CONFIG_LOADS_ECHO 1 /* Echo on for serial download */ - -/* - * Miscellaneous configurable options - */ - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x000fa000 /* 1 MB in SRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 1250000 } - - -/* - * Low Level Configuration Settings - */ - -/* - * Internal Memory Mapped (This is not the IMMR content) - */ -#define CONFIG_SYS_IMMR 0x01000000 /* Physical start adress of internal memory map */ - -/* - * Definitions for initial stack pointer and data area - */ -#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_IMMR + 0x003f9800) /* Physical start adress of internal MPC555 writable RAM */ -#define CONFIG_SYS_INIT_RAM_SIZE (CONFIG_SYS_IMMR + 0x003fffff) /* Physical end adress of internal MPC555 used RAM area */ -#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - CONFIG_SYS_INIT_RAM_ADDR) - GENERATED_GBL_DATA_SIZE) /* Offset from the beginning of ram */ -#define CONFIG_SYS_INIT_SP_ADDR 0x013fa000 /* Physical start adress of inital stack */ - -/* - * Start addresses for the final memory configuration - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Monitor won't change memory map */ -#define CONFIG_SYS_FLASH_BASE 0x02000000 /* External flash */ -#define PLD_BASE 0x03000000 /* PLD */ -#define ANYBUS_BASE 0x03010000 /* Anybus Module */ - -#define CONFIG_SYS_RESET_ADRESS 0x01000000 /* Adress which causes reset */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* CONFIG_SYS_TEXT_BASE is defined in the board config.mk file. */ - /* This adress is given to the linker with -Ttext to */ - /* locate the text section at this adress. */ -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (64 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - - -/*----------------------------------------------------------------------- - * FLASH organization - *----------------------------------------------------------------------- - * - */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors on one chip */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Physically section protection on */ - -#define CONFIG_ENV_IS_IN_FLASH 1 - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_OFFSET 0x00020000 /* Environment starts at this adress */ -#define CONFIG_ENV_SIZE 0x00010000 /* Set whole sector as env */ -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWP) -#endif /* CONFIG_WATCHDOG */ - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PITF) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF00 -#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_RTDIV | SCCR_RTSEL | \ - SCCR_COM00 | SCCR_DFNL000 | SCCR_DFNH000) - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration - *----------------------------------------------------------------------- - * Data show cycle - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00) /* Disable data show cycle */ - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register - *----------------------------------------------------------------------- - * Set all bits to 40 Mhz - * - */ -#define CONFIG_SYS_OSC_CLK ((uint)4000000) /* Oscillator clock is 4MHz */ -#define CONFIG_SYS_PLPRCR (PLPRCR_MF_9 | PLPRCR_DIVF_0) - - -/*----------------------------------------------------------------------- - * UMCR - UIMB Module Configuration Register - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_UMCR (UMCR_FSPEED) /* IMB clock same as U-bus */ - -/*----------------------------------------------------------------------- - * ICTRL - I-Bus Support Control Register - */ -#define CONFIG_SYS_ICTRL (ICTRL_ISCT_SER_7) /* Take out of serialized mode */ - -/*----------------------------------------------------------------------- - * USIU - Memory Controller Register - *----------------------------------------------------------------------- - */ - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | BR_V | BR_BI | BR_PS_16) -#define CONFIG_SYS_OR0_PRELIM (OR_ADDR_MK_FF | OR_SCY_3) -#define CONFIG_SYS_BR1_PRELIM (ANYBUS_BASE) -#define CONFIG_SYS_OR1_PRELIM (OR_ADDR_MK_FFFF | OR_SCY_1 | OR_ETHR) -#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_SDRAM_BASE | BR_V | BR_PS_32) -#define CONFIG_SYS_OR2_PRELIM (OR_ADDR_MK_FF) -#define CONFIG_SYS_BR3_PRELIM (PLD_BASE | BR_V | BR_BI | BR_LBDIR | BR_PS_8) -#define CONFIG_SYS_OR3_PRELIM (OR_ADDR_MK_FF | OR_TRLX | OR_BSCY | OR_SCY_8 | \ - OR_ACS_10 | OR_ETHR | OR_CSNT) - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* We don't realign the flash */ - -/*----------------------------------------------------------------------- - * DER - Timer Decrementer - *----------------------------------------------------------------------- - * Initialise to zero - */ -#define CONFIG_SYS_DER 0x00000000 - -#endif /* __CONFIG_H */ |