diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/arndale.h | 4 | ||||
| -rw-r--r-- | include/configs/at91-sama5_common.h | 8 | ||||
| -rw-r--r-- | include/configs/ls1021atwr.h | 6 | ||||
| -rw-r--r-- | include/configs/lwmon5.h | 633 | ||||
| -rw-r--r-- | include/configs/pcm052.h | 120 | ||||
| -rw-r--r-- | include/configs/smartweb.h | 4 | ||||
| -rw-r--r-- | include/configs/sunxi-common.h | 42 | ||||
| -rw-r--r-- | include/configs/tegra114-common.h | 2 | ||||
| -rw-r--r-- | include/configs/tegra20-common.h | 2 | ||||
| -rw-r--r-- | include/configs/tegra210-common.h | 2 | ||||
| -rw-r--r-- | include/configs/tegra30-common.h | 2 | ||||
| -rw-r--r-- | include/configs/ti_omap3_common.h | 2 | ||||
| -rw-r--r-- | include/configs/vexpress_aemv8a.h | 61 |
13 files changed, 818 insertions, 70 deletions
diff --git a/include/configs/arndale.h b/include/configs/arndale.h index 437a745414..b08f341227 100644 --- a/include/configs/arndale.h +++ b/include/configs/arndale.h @@ -49,6 +49,10 @@ /* The PERIPHBASE in the CBAR register is wrong on the Arndale, so override it */ #define CONFIG_ARM_GIC_BASE_ADDRESS 0x10480000 +/* CPU Errata */ +#define CONFIG_ARM_ERRATA_773022 +#define CONFIG_ARM_ERRATA_774769 + /* Power */ #define CONFIG_POWER #define CONFIG_POWER_I2C diff --git a/include/configs/at91-sama5_common.h b/include/configs/at91-sama5_common.h index 3d6b0ae0c3..a5990cec03 100644 --- a/include/configs/at91-sama5_common.h +++ b/include/configs/at91-sama5_common.h @@ -53,6 +53,13 @@ #define CONFIG_CMD_DHCP #ifdef CONFIG_SYS_USE_MMC + +#ifdef CONFIG_ENV_IS_IN_MMC +/* Use raw reserved sectors to save environment */ +#define CONFIG_ENV_OFFSET 0x2000 +#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_SYS_MMC_ENV_DEV 0 +#else /* u-boot env in sd/mmc card */ #define CONFIG_ENV_IS_IN_FAT #define CONFIG_FAT_WRITE @@ -60,6 +67,7 @@ #define FAT_ENV_DEVICE_AND_PART "0" #define FAT_ENV_FILE "uboot.env" #define CONFIG_ENV_SIZE 0x4000 +#endif #define CONFIG_BOOTCOMMAND "if test ! -n ${dtb_name}; then " \ "setenv dtb_name at91-${board_name}.dtb; " \ diff --git a/include/configs/ls1021atwr.h b/include/configs/ls1021atwr.h index f6bd5fcece..02cc09c82b 100644 --- a/include/configs/ls1021atwr.h +++ b/include/configs/ls1021atwr.h @@ -310,12 +310,16 @@ #define FSL_QSPI_FLASH_NUM 2 #define CONFIG_SPI_FLASH_STMICRO +/* DSPI */ +#define CONFIG_FSL_DSPI +#define CONFIG_SPI_FLASH_ATMEL +#endif + /* DM SPI */ #if defined(CONFIG_FSL_DSPI) || defined(CONFIG_FSL_QSPI) #define CONFIG_CMD_SF #define CONFIG_DM_SPI_FLASH #endif -#endif /* * Video diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h new file mode 100644 index 0000000000..26136a52ce --- /dev/null +++ b/include/configs/lwmon5.h @@ -0,0 +1,633 @@ +/* + * (C) Copyright 2007-2013 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * lwmon5.h - configuration for lwmon5 board + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * Liebherr extra version info + */ +#define CONFIG_IDENT_STRING " - v2.0" + +/* + * High Level Configuration Options + */ +#define CONFIG_LWMON5 1 /* Board is lwmon5 */ +#define CONFIG_440EPX 1 /* Specific PPC440EPx */ +#define CONFIG_440 1 /* ... PPC440 family */ + +#define CONFIG_SYS_GENERIC_BOARD + +#define CONFIG_SYS_TEXT_BASE 0xFFF80000 +#define CONFIG_HOSTNAME lwmon5 + +#define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */ + +#define CONFIG_4xx_DCACHE /* enable cache in SDRAM */ + +#define CONFIG_BOARD_EARLY_INIT_F /* Call board_early_init_f */ +#define CONFIG_BOARD_EARLY_INIT_R /* Call board_early_init_r */ +#define CONFIG_BOARD_POSTCLK_INIT /* Call board_postclk_init */ +#define CONFIG_MISC_INIT_R /* Call misc_init_r */ +#define CONFIG_BOARD_RESET /* Call board_reset */ + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* Start of U-Boot */ +#define CONFIG_SYS_MONITOR_LEN 0x80000 +#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* Reserved for malloc */ + +#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */ +#define CONFIG_SYS_LIME_BASE_0 0xc0000000 +#define CONFIG_SYS_LIME_BASE_1 0xc1000000 +#define CONFIG_SYS_LIME_BASE_2 0xc2000000 +#define CONFIG_SYS_LIME_BASE_3 0xc3000000 +#define CONFIG_SYS_FPGA_BASE_0 0xc4000000 +#define CONFIG_SYS_FPGA_BASE_1 0xc4200000 +#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ +#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CONFIG_SYS_PCI_MEMBASE1 (CONFIG_SYS_PCI_MEMBASE + 0x10000000) +#define CONFIG_SYS_PCI_MEMBASE2 (CONFIG_SYS_PCI_MEMBASE1 + 0x10000000) +#define CONFIG_SYS_PCI_MEMBASE3 (CONFIG_SYS_PCI_MEMBASE2 + 0x10000000) + +#define CONFIG_SYS_USB2D0_BASE 0xe0000100 +#define CONFIG_SYS_USB_DEVICE 0xe0000000 +#define CONFIG_SYS_USB_HOST 0xe0000400 + +/* + * Initial RAM & stack pointer + * + * On LWMON5 we use D-cache as init-ram and stack pointer. We also move + * the POST_WORD from OCM to a 440EPx register that preserves it's + * content during reset (GPT0_COMP6). This way we reserve the OCM (16k) + * for logbuffer only. (GPT0_COMP1-COMP5 are reserved for logbuffer header.) + */ +#define CONFIG_SYS_INIT_RAM_DCACHE 1 /* d-cache as init ram */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* DCache */ +#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* unused GPT0 COMP reg */ +#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6) +#define CONFIG_SYS_OCM_SIZE (16 << 10) +/* 440EPx errata CHIP 11: don't use last 4kbytes */ +#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) + +/* Additional registers for watchdog timer post test */ +#define CONFIG_SYS_WATCHDOG_TIME_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK2) +#define CONFIG_SYS_WATCHDOG_FLAGS_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_MASK1) +#define CONFIG_SYS_DSPIC_TEST_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR +#define CONFIG_SYS_OCM_STATUS_ADDR CONFIG_SYS_WATCHDOG_FLAGS_ADDR +#define CONFIG_SYS_WATCHDOG_MAGIC 0x12480000 +#define CONFIG_SYS_WATCHDOG_MAGIC_MASK 0xFFFF0000 +#define CONFIG_SYS_DSPIC_TEST_MASK 0x00000001 +#define CONFIG_SYS_OCM_STATUS_OK 0x00009A00 +#define CONFIG_SYS_OCM_STATUS_FAIL 0x0000A300 +#define CONFIG_SYS_OCM_STATUS_MASK 0x0000FF00 + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 2 /* Use UART1 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external clock provided */ +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH /* use FLASH for environment vars */ + +/* + * FLASH related + */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ + +#define CONFIG_SYS_FLASH0 0xFC000000 +#define CONFIG_SYS_FLASH1 0xF8000000 +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 } + +#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_PROTECTION /* use hardware flash protection */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_QUIET_TEST /* don't warn upon unknown flash */ + +#define CONFIG_ENV_SECT_SIZE 0x40000 /* size of one complete sector */ +#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN) - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +/* + * DDR SDRAM + */ +#define CONFIG_SYS_MBYTES_SDRAM 256 +#define CONFIG_SYS_DDR_CACHED_ADDR 0x40000000 /* setup 2nd TLB cached here */ +#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ +#define CONFIG_DDR_ECC /* enable ECC */ + +/* POST support */ +#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_ECC | \ + CONFIG_SYS_POST_ETHER | \ + CONFIG_SYS_POST_FPU | \ + CONFIG_SYS_POST_I2C | \ + CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_OCM | \ + CONFIG_SYS_POST_RTC | \ + CONFIG_SYS_POST_SPR | \ + CONFIG_SYS_POST_UART | \ + CONFIG_SYS_POST_SYSMON | \ + CONFIG_SYS_POST_WATCHDOG | \ + CONFIG_SYS_POST_DSP | \ + CONFIG_SYS_POST_BSPEC1 | \ + CONFIG_SYS_POST_BSPEC2 | \ + CONFIG_SYS_POST_BSPEC3 | \ + CONFIG_SYS_POST_BSPEC4 | \ + CONFIG_SYS_POST_BSPEC5) + +/* Define here the base-addresses of the UARTs to test in POST */ +#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \ + CONFIG_SYS_NS16550_COM2 } + +#define CONFIG_POST_UART { \ + "UART test", \ + "uart", \ + "This test verifies the UART operation.", \ + POST_RAM | POST_SLOWTEST | POST_ALWAYS | POST_MANUAL, \ + &uart_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_UART \ + } + +#define CONFIG_POST_WATCHDOG { \ + "Watchdog timer test", \ + "watchdog", \ + "This test checks the watchdog timer.", \ + POST_RAM | POST_POWERON | POST_SLOWTEST | POST_MANUAL | POST_REBOOT, \ + &lwmon5_watchdog_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_WATCHDOG \ + } + +#define CONFIG_POST_BSPEC1 { \ + "dsPIC init test", \ + "dspic_init", \ + "This test returns result of dsPIC READY test run earlier.", \ + POST_RAM | POST_ALWAYS, \ + &dspic_init_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_BSPEC1 \ + } + +#define CONFIG_POST_BSPEC2 { \ + "dsPIC test", \ + "dspic", \ + "This test gets result of dsPIC POST and dsPIC version.", \ + POST_RAM | POST_ALWAYS, \ + &dspic_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_BSPEC2 \ + } + +#define CONFIG_POST_BSPEC3 { \ + "FPGA test", \ + "fpga", \ + "This test checks FPGA registers and memory.", \ + POST_RAM | POST_ALWAYS | POST_MANUAL, \ + &fpga_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_BSPEC3 \ + } + +#define CONFIG_POST_BSPEC4 { \ + "GDC test", \ + "gdc", \ + "This test checks GDC registers and memory.", \ + POST_RAM | POST_ALWAYS | POST_MANUAL,\ + &gdc_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_BSPEC4 \ + } + +#define CONFIG_POST_BSPEC5 { \ + "SYSMON1 test", \ + "sysmon1", \ + "This test checks GPIO_62_EPX pin indicating power failure.", \ + POST_RAM | POST_MANUAL | POST_NORMAL | POST_SLOWTEST, \ + &sysmon1_post_test, \ + NULL, \ + NULL, \ + CONFIG_SYS_POST_BSPEC5 \ + } + +#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ +#define CONFIG_LOGBUFFER +/* Reserve GPT0_COMP1-COMP5 for logbuffer header */ +#define CONFIG_ALT_LH_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP1) +#define CONFIG_ALT_LB_ADDR (CONFIG_SYS_OCM_BASE) +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ + +/* + * I2C + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F + +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* RTC */ +#define CONFIG_SYS_I2C_EEPROM_CPU_ADDR 0x52 /* EEPROM (CPU Modul) */ +#define CONFIG_SYS_I2C_EEPROM_MB_ADDR 0x53 /* EEPROM AT24C128 (MainBoard) */ +#define CONFIG_SYS_I2C_DSPIC_ADDR 0x54 /* dsPIC */ +#define CONFIG_SYS_I2C_DSPIC_2_ADDR 0x55 /* dsPIC */ +#define CONFIG_SYS_I2C_DSPIC_KEYB_ADDR 0x56 /* dsPIC */ +#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* dsPIC */ + +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel AT24C128 has */ + /* 64 byte page write mode using*/ + /* last 6 bits of the address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE + +#define CONFIG_RTC_PCF8563 /* enable Philips PCF8563 RTC */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */ +#define CONFIG_SYS_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ +#define CONFIG_SYS_I2C_DSPIC_IO_ADDR 0x57 /* PIC I/O addr */ + +#define CONFIG_SYS_POST_I2C_ADDRS {CONFIG_SYS_I2C_RTC_ADDR, \ + CONFIG_SYS_I2C_EEPROM_CPU_ADDR,\ + CONFIG_SYS_I2C_EEPROM_MB_ADDR, \ + CONFIG_SYS_I2C_DSPIC_ADDR, \ + CONFIG_SYS_I2C_DSPIC_2_ADDR, \ + CONFIG_SYS_I2C_DSPIC_KEYB_ADDR,\ + CONFIG_SYS_I2C_DSPIC_IO_ADDR } + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +/* Update size in "reg" property of NOR FLASH device tree nodes */ +#define CONFIG_FDT_FIXUP_NOR_FLASH_SIZE + +#define CONFIG_FIT /* enable FIT image support */ + +#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ + +#define CONFIG_PREBOOT "setenv bootdelay 15" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hostname=lwmon5\0" \ + "netdev=eth0\0" \ + "unlock=yes\0" \ + "logversion=2\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\ + "addmisc=setenv bootargs ${bootargs} rtc-pcf8563.probe=0,0x51\0"\ + "flash_nfs=run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};" \ + "run nfsargs addip addtty addmisc;bootm\0" \ + "rootpath=/opt/eldk/ppc_4xxFP\0" \ + "bootfile=/tftpboot/lwmon5/uImage\0" \ + "kernel_addr=FC000000\0" \ + "ramdisk_addr=FC180000\0" \ + "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ + "update=protect off FFF80000 FFFFFFFF;era FFF80000 FFFFFFFF;" \ + "cp.b 200000 FFF80000 80000\0" \ + "upd=run load update\0" \ + "lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;" \ + "autoscr 200000\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_PPC4xx_EMAC +#define CONFIG_IBM_EMAC4_V4 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 3 /* PHY address, See schematics */ + +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_RESET_DELAY 300 + +#define CONFIG_HAS_ETH0 +#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ +#define CONFIG_PHY1_ADDR 1 + +/* Video console */ +#define CONFIG_VIDEO +#define CONFIG_VIDEO_MB862xx +#define CONFIG_VIDEO_MB862xx_ACCEL +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_LOGO +#define CONFIG_CONSOLE_EXTRA_INFO +#define VIDEO_FB_16BPP_PIXEL_SWAP +#define VIDEO_FB_16BPP_WORD_SWAP + +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_SPLASH_SCREEN + +/* + * USB/EHCI + */ +#define CONFIG_USB_EHCI /* Enable EHCI USB support */ +#define CONFIG_USB_EHCI_PPC4XX /* on PPC4xx platform */ +#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300 +#define CONFIG_EHCI_MMIO_BIG_ENDIAN +#define CONFIG_EHCI_DESC_BIG_ENDIAN +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* re-init HCD after CMD_RESET */ +#define CONFIG_USB_STORAGE + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_FAT +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SDRAM + +#ifdef CONFIG_VIDEO +#define CONFIG_CMD_BMP +#endif + +#ifdef CONFIG_440EPX +#define CONFIG_CMD_USB +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SUPPORT_VFAT + +#define CONFIG_SYS_LONGHELP /* undef to save memory */ + +#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup*/ + +#ifndef DEBUG +#define CONFIG_HW_WATCHDOG 1 /* Use external HW-Watchdog */ +#endif +#define CONFIG_WD_PERIOD 40000 /* in usec */ +#define CONFIG_WD_MAX_RATE 66600 /* in ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 16 MB of memory, since this is + * the maximum mapped by the 40x Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ + +/* + * External Bus Controller (EBC) Setup + */ +#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE + +/* Memory Bank 0 (NOR-FLASH) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x03000280 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0xfc000) + +/* Memory Bank 1 (Lime) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x01004380 +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_LIME_BASE_0 | 0xbc000) + +/* Memory Bank 2 (FPGA) initialization */ +#define CONFIG_SYS_EBC_PB2AP 0x01004400 +#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA_BASE_0 | 0x1c000) + +/* Memory Bank 3 (FPGA2) initialization */ +#define CONFIG_SYS_EBC_PB3AP 0x01004400 +#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_FPGA_BASE_1 | 0x1c000) + +#define CONFIG_SYS_EBC_CFG 0xb8400000 + +/* + * Graphics (Fujitsu Lime) + */ +/* SDRAM Clock frequency adjustment register */ +#define CONFIG_SYS_LIME_SDRAM_CLOCK 0xC1FC0038 +#if 1 /* 133MHz is not tested enough, use 100MHz for now */ +/* Lime Clock frequency is to set 100MHz */ +#define CONFIG_SYS_LIME_CLOCK_100MHZ 0x00000 +#else +/* Lime Clock frequency for 133MHz */ +#define CONFIG_SYS_LIME_CLOCK_133MHZ 0x10000 +#endif + +/* SDRAM Parameter register */ +#define CONFIG_SYS_LIME_MMR 0xC1FCFFFC +/* + * SDRAM parameter value; was 0x414FB7F2, caused several vertical bars + * and pixel flare on display when 133MHz was configured. According to + * SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed + * Grade + */ +#ifdef CONFIG_SYS_LIME_CLOCK_133MHZ +#define CONFIG_SYS_MB862xx_MMR 0x414FB7F3 +#define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_133MHZ +#else +#define CONFIG_SYS_MB862xx_MMR 0x414FB7F2 +#define CONFIG_SYS_MB862xx_CCF CONFIG_SYS_LIME_CLOCK_100MHZ +#endif + +/* + * GPIO Setup + */ +#define CONFIG_SYS_GPIO_PHY1_RST 12 +#define CONFIG_SYS_GPIO_FLASH_WP 14 +#define CONFIG_SYS_GPIO_PHY0_RST 22 +#define CONFIG_SYS_GPIO_PERM_VOLT_FEED 49 +#define CONFIG_SYS_GPIO_DSPIC_READY 51 +#define CONFIG_SYS_GPIO_CAN_ENABLE 53 +#define CONFIG_SYS_GPIO_LSB_ENABLE 54 +#define CONFIG_SYS_GPIO_EEPROM_EXT_WP 55 +#define CONFIG_SYS_GPIO_HIGHSIDE 56 +#define CONFIG_SYS_GPIO_EEPROM_INT_WP 57 +#define CONFIG_SYS_GPIO_BOARD_RESET 58 +#define CONFIG_SYS_GPIO_LIME_S 59 +#define CONFIG_SYS_GPIO_LIME_RST 60 +#define CONFIG_SYS_GPIO_SYSMON_STATUS 62 +#define CONFIG_SYS_GPIO_WATCHDOG 63 + +#define GPIO49_VAL 1 + +/* + * PPC440 GPIO Configuration + */ +#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +{ \ +/* GPIO Core 0 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 EBC_ADDR(6) DMA_ACK(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 EBC_ADDR(5) DMA_EOT/TC(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 EBC_ADDR(4) DMA_REQ(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 EBC_ADDR(3) DMA_ACK(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 EBC_ADDR(2) DMA_EOT/TC(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 EBC_CS_N(1) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 EBC_CS_N(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS_N(3) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS_N(4) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS_N(5) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 EBC_BUS_ERR */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO12 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO13 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO14 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO15 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 GMCTxD(4) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMCTxD(5) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMCTxD(6) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 GMCTxD(7) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 RejectPkt0 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 RejectPkt1 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO22 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 SCPD0 */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 GMCTxD(2) */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 GMCTxD(3) */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO26 */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EXT_EBC_REQ USB2D_RXERROR */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 USB2D_TXVALID */ \ +{GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO29 EBC_EXT_HDLA USB2D_PAD_SUSPNDM */ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 EBC_EXT_ACK USB2D_XCVRSELECT*/ \ +{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO31 EBC_EXR_BUSREQ USB2D_TERMSELECT*/ \ +}, \ +{ \ +/* GPIO Core 1 */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO32 USB2D_OPMODE0 EBC_DATA(2) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO33 USB2D_OPMODE1 EBC_DATA(3) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_0}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N EBC_DATA(0) UART3_SIN*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EBC_DATA(1) UART3_SOUT*/ \ +{GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 UIC_IRQ(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 UIC_IRQ(1) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 UIC_IRQ(2) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 UIC_IRQ(3) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO44 UIC_IRQ(4) DMA_ACK(1) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO45 UIC_IRQ(6) DMA_EOT/TC(1) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 UIC_IRQ(7) DMA_REQ(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 UIC_IRQ(8) DMA_ACK(0) */ \ +{GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 UIC_IRQ(9) DMA_EOT/TC(0) */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO49_VAL}, /* GPIO49 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO50 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO51 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO52 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO53 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO54 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO55 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO57 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO62 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO63 Unselect via TraceSelect Bit */ \ +} \ +} + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#endif + +#endif /* __CONFIG_H */ diff --git a/include/configs/pcm052.h b/include/configs/pcm052.h index 903f94c17e..150698ecaa 100644 --- a/include/configs/pcm052.h +++ b/include/configs/pcm052.h @@ -60,14 +60,15 @@ #define CONFIG_CMD_MTDPARTS #define CONFIG_MTD_PARTITIONS #define CONFIG_MTD_DEVICE -#define MTDIDS_DEFAULT "nand0=NAND,nor0=qspi0-a,nor1=qspi0-b" +#define MTDIDS_DEFAULT "nand0=NAND" #define MTDPARTS_DEFAULT "mtdparts=NAND:256k(spare)"\ ",384k(bootloader)"\ ",128k(env1)"\ ",128k(env2)"\ - ",3840k(kernel)"\ - ",-(rootfs)"\ - ",qspi0-a:-(jffs2),qspio0-b:-(jffs2)" + ",128k(dtb)"\ + ",6144k(kernel)"\ + ",65536k(ramdisk)"\ + ",450944k(root)" #endif #define CONFIG_MMC @@ -135,36 +136,85 @@ #define CONFIG_BOARD_SIZE_LIMIT 524288 #define CONFIG_BOOTCOMMAND "run bootcmd_sd" -#define CONFIG_EXTRA_ENV_SETTINGS \ - "bootfile=uImage\0" \ - "bootargs_base=setenv bootargs rw mem=256M " \ - "console=ttymxc1,115200n8\0" \ - "bootargs_sd=setenv bootargs ${bootargs} " \ - "root=/dev/mmcblk0p2 rootwait\0" \ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "blimg_file=u-boot.imx\0" \ + "blsec_addr=0x81000000\0" \ + "blimg_addr=0x81000400\0" \ + "kernel_file=zImage\0" \ + "kernel_addr=0x82000000\0" \ + "fdt_file=vf610-pcm052.dtb\0" \ + "fdt_addr=0x81000000\0" \ + "ram_file=uRamdisk\0" \ + "ram_addr=0x83000000\0" \ + "filesys=rootfs.ubifs\0" \ + "sys_addr=0x81000000\0" \ + "tftploc=/path/to/tftp/directory/\0" \ + "nfs_root=/path/to/nfs/root\0" \ + "tftptimeout=1000\0" \ + "tftptimeoutcountmax=1000000\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "bootargs_base=setenv bootargs rw mem=256M " \ + "console=ttyLP1,115200n8\0" \ + "bootargs_sd=setenv bootargs ${bootargs} " \ + "root=/dev/mmcblk0p2 rootwait\0" \ "bootargs_net=setenv bootargs ${bootargs} root=/dev/nfs ip=dhcp " \ - "nfsroot=${serverip}:${nfs_root},v3,tcp\0" \ - "bootargs_nand=setenv bootargs ${bootargs} " \ - "root=/dev/mtdblock2 rootfstype=jffs2\0" \ - "bootargs_mtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ - "bootcmd_sd=run bootargs_base bootargs_sd bootargs_mtd; mmc rescan; " \ - "fatload mmc 0:1 ${loadaddr} ${bootfile}; bootm ${loadaddr}\0" \ - "bootcmd_net=run bootargs_base bootargs_net bootargs_mtd; " \ - "tftpboot ${loadaddr} ${tftploc}${bootfile}; bootm\0" \ - "bootcmd_nand='run bootargs_base bootargs_nand bootargs_mtd; " \ - "nand read ${loadaddr} 0x000E0000 0x3C0000; " \ - "bootm ${loadaddr}\0" \ - "tftploc=/path/to/tftp/directory/\0" \ - "nfs_root=/path/to/nfs/root\0" \ - "mtdparts=" MTDPARTS_DEFAULT "\0" \ - "update_kernel_from_sd=mw.b $(loadaddr) 0xff 0x3C0000; " \ - "mmc rescan; fatload mmc 0:2 ${loadaddr} ${bootfile}; " \ - "nand erase 0xE0000 0x3C0000; " \ - "nand write.i ${loadaddr} 0xE0000 0x3C0000\0" \ - "update_rootfs_from_tftp=mw.b ${loadaddr} 0xff 0x8F20000; " \ - "tftp ${loadaddr} ${tftp}${filesys}; " \ - "nand erase 0x4A0000 0x8F20000; " \ - "nand write.i ${loadaddr} 0x4A0000 0x8F20000\0" \ - "filesys=rootfs.jffs2\0" + "nfsroot=${serverip}:${nfs_root},v3,tcp\0" \ + "bootargs_nand=setenv bootargs ${bootargs} " \ + "ubi.mtd=6 rootfstype=ubifs root=ubi0:rootfs\0" \ + "bootargs_ram=setenv bootargs ${bootargs} " \ + "root=/dev/ram rw initrd=${ram_addr}\0" \ + "bootargs_mtd=setenv bootargs ${bootargs} ${mtdparts}\0" \ + "bootcmd_sd=run bootargs_base bootargs_sd bootargs_mtd; " \ + "fatload mmc 0:1 ${kernel_addr} ${kernel_file}; " \ + "fatload mmc 0:1 ${fdt_addr} ${fdt_file}; " \ + "bootz ${kernel_addr} - ${fdt_addr}\0" \ + "bootcmd_net=run bootargs_base bootargs_net bootargs_mtd; " \ + "tftpboot ${kernel_addr} ${tftpdir}${kernel_file}; " \ + "tftpboot ${fdt_addr} ${tftpdir}${fdt_file}; " \ + "bootz ${kernel_addr} - ${fdt_addr}\0" \ + "bootcmd_nand=run bootargs_base bootargs_nand bootargs_mtd; " \ + "nand read ${fdt_addr} dtb; " \ + "nand read ${kernel_addr} kernel; " \ + "bootz ${kernel_addr} - ${fdt_addr}\0" \ + "bootcmd_ram=run bootargs_base bootargs_ram bootargs_mtd; " \ + "nand read ${fdt_addr} dtb; " \ + "nand read ${kernel_addr} kernel; " \ + "nand read ${ram_addr} ramdisk; " \ + "bootz ${kernel_addr} ${ram_addr} ${fdt_addr}\0" \ + "update_bootloader_from_tftp=mtdparts default; " \ + "nand read ${blsec_addr} bootloader; " \ + "mw.b ${blimg_addr} 0xff 0x5FC00; " \ + "if tftp ${blimg_addr} ${tftpdir}${blimg_file}; then " \ + "nand erase.part bootloader; " \ + "nand write ${blsec_addr} bootloader ${filesize}; fi\0" \ + "update_kernel_from_sd=if fatload mmc 0:2 ${kernel_addr} " \ + "${kernel_file}; " \ + "then mtdparts default; " \ + "nand erase.part kernel; " \ + "nand write ${kernel_addr} kernel ${filesize}; " \ + "if fatload mmc 0:2 ${fdt_addr} ${fdt_file}; then " \ + "nand erase.part dtb; " \ + "nand write ${fdt_addr} dtb ${filesize}; fi\0" \ + "update_kernel_from_tftp=if tftp ${fdt_addr} ${tftpdir}${fdt_file}; " \ + "then setenv fdtsize ${filesize}; " \ + "if tftp ${kernel_addr} ${tftpdir}${kernel_file}; then " \ + "mtdparts default; " \ + "nand erase.part dtb; " \ + "nand write ${fdt_addr} dtb ${fdtsize}; " \ + "nand erase.part kernel; " \ + "nand write ${kernel_addr} kernel ${filesize}; fi; fi\0" \ + "update_rootfs_from_tftp=if tftp ${sys_addr} ${tftpdir}${filesys}; " \ + "then mtdparts default; " \ + "nand erase.part root; " \ + "ubi part root; " \ + "ubi create rootfs; " \ + "ubi write ${sys_addr} rootfs ${filesize}; fi\0" \ + "update_ramdisk_from_tftp=if tftp ${ram_addr} ${tftpdir}${ram_file}; " \ + "then mtdparts default; " \ + "nand erase.part ramdisk; " \ + "nand write ${ram_addr} ramdisk ${filesize}; fi\0" /* miscellaneous commands */ #define CONFIG_CMD_ELF @@ -220,9 +270,9 @@ #ifdef CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_SECT_SIZE (128 * 1024) #define CONFIG_ENV_SIZE (8 * 1024) -#define CONFIG_ENV_OFFSET 0x80000 +#define CONFIG_ENV_OFFSET 0xA0000 #define CONFIG_ENV_SIZE_REDUND (8 * 1024) -#define CONFIG_ENV_OFFSET_REDUND 0xA0000 +#define CONFIG_ENV_OFFSET_REDUND 0xC0000 #endif #define CONFIG_OF_LIBFDT diff --git a/include/configs/smartweb.h b/include/configs/smartweb.h index d189c3fde9..e11c016aed 100644 --- a/include/configs/smartweb.h +++ b/include/configs/smartweb.h @@ -117,6 +117,9 @@ * */ #define CONFIG_MACB +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_ASIX +#define CONFIG_USB_ETHER_MCS7830 #define CONFIG_RMII /* use reduced MII inteface */ #define CONFIG_NET_RETRY_COUNT 20 /* # of DHCP/BOOTP retries */ #define CONFIG_AT91_WANTS_COMMON_PHY @@ -182,6 +185,7 @@ /* General Boot Parameter */ #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTCOMMAND "run flashboot" +#define CONFIG_BOOT_RETRY_TIME 30 #define CONFIG_SYS_CBSIZE 512 #define CONFIG_SYS_MAXARGS 16 #define CONFIG_SYS_PBSIZE \ diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h index 48cc4ed6f6..e1ba7914cd 100644 --- a/include/configs/sunxi-common.h +++ b/include/configs/sunxi-common.h @@ -13,6 +13,7 @@ #ifndef _SUNXI_COMMON_CONFIG_H #define _SUNXI_COMMON_CONFIG_H +#include <asm/arch/cpu.h> #include <linux/stringify.h> #ifdef CONFIG_OLD_SUNXI_KERNEL_COMPAT @@ -39,23 +40,14 @@ #define CONFIG_SYS_THUMB_BUILD /* Thumbs mode to save space in SPL */ #endif -#include <asm/arch/cpu.h> /* get chip and board defs */ - -#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_DM_SERIAL) -# define CONFIG_DW_SERIAL -#endif - -/* - * Display CPU information - */ -#define CONFIG_DISPLAY_CPUINFO - /* Serial & console */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL /* ns16550 reg in the low bits of cpu reg */ #define CONFIG_SYS_NS16550_CLK 24000000 -#ifndef CONFIG_DM_SERIAL +#ifdef CONFIG_DM_SERIAL +# define CONFIG_DW_SERIAL +#else # define CONFIG_SYS_NS16550_REG_SIZE -4 # define CONFIG_SYS_NS16550_COM1 SUNXI_UART0_BASE # define CONFIG_SYS_NS16550_COM2 SUNXI_UART1_BASE @@ -65,6 +57,7 @@ #endif /* CPU */ +#define CONFIG_DISPLAY_CPUINFO #define CONFIG_SYS_CACHELINE_SIZE 64 /* @@ -152,8 +145,8 @@ #define CONFIG_SYS_MMC_ENV_DEV 0 /* first detected MMC controller */ #endif -/* 4MB of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (4 << 20)) +/* 64MB of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (64 << 20)) /* * Miscellaneous configurable options @@ -282,11 +275,7 @@ extern int soft_i2c_gpio_scl; * The amount of RAM to keep free at the top of RAM when relocating u-boot, * to use as framebuffer. This must be a multiple of 4096. */ -#ifdef CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804 -#define CONFIG_SUNXI_MAX_FB_SIZE (12 << 20) -#else -#define CONFIG_SUNXI_MAX_FB_SIZE (9 << 20) -#endif +#define CONFIG_SUNXI_MAX_FB_SIZE (16 << 20) /* Do we want to initialize a simple FB? */ #define CONFIG_VIDEO_DT_SIMPLEFB @@ -393,12 +382,12 @@ extern int soft_i2c_gpio_scl; #define CONFIG_PRE_CON_BUF_SZ 4096 /* Aprox 2 80*25 screens */ /* - * 240M RAM (256M minimum minus space for the framebuffer), + * 160M RAM (256M minimum minus 64MB heap + 32MB for u-boot, stack, fb, etc. * 32M uncompressed kernel, 16M compressed kernel, 1M fdt, * 1M script, 1M pxe and the ramdisk at the end. */ #define MEM_LAYOUT_ENV_SETTINGS \ - "bootm_size=0xf000000\0" \ + "bootm_size=0xa000000\0" \ "kernel_addr_r=" __stringify(SDRAM_OFFSET(2000000)) "\0" \ "fdt_addr_r=" __stringify(SDRAM_OFFSET(3000000)) "\0" \ "scriptaddr=" __stringify(SDRAM_OFFSET(3100000)) "\0" \ @@ -423,7 +412,18 @@ extern int soft_i2c_gpio_scl; #define BOOT_TARGET_DEVICES_USB(func) #endif +/* FEL boot support, auto-execute boot.scr if a script address was provided */ +#define BOOTENV_DEV_FEL(devtypeu, devtypel, instance) \ + "bootcmd_fel=" \ + "if test -n ${fel_booted} && test -n ${fel_scriptaddr}; then " \ + "echo '(FEL boot)'; " \ + "source ${fel_scriptaddr}; " \ + "fi\0" +#define BOOTENV_DEV_NAME_FEL(devtypeu, devtypel, instance) \ + "fel " + #define BOOT_TARGET_DEVICES(func) \ + func(FEL, fel, na) \ BOOT_TARGET_DEVICES_MMC(func) \ BOOT_TARGET_DEVICES_SCSI(func) \ BOOT_TARGET_DEVICES_USB(func) \ diff --git a/include/configs/tegra114-common.h b/include/configs/tegra114-common.h index 252e607d73..671071ba98 100644 --- a/include/configs/tegra114-common.h +++ b/include/configs/tegra114-common.h @@ -34,7 +34,7 @@ /*----------------------------------------------------------------------- * Physical Memory Map */ -#define CONFIG_SYS_TEXT_BASE 0x8010E000 +#define CONFIG_SYS_TEXT_BASE 0x80110000 /* * Memory layout for where various images get loaded by boot scripts: diff --git a/include/configs/tegra20-common.h b/include/configs/tegra20-common.h index 0841f33bfc..00e85c48c4 100644 --- a/include/configs/tegra20-common.h +++ b/include/configs/tegra20-common.h @@ -32,7 +32,7 @@ /*----------------------------------------------------------------------- * Physical Memory Map */ -#define CONFIG_SYS_TEXT_BASE 0x0010E000 +#define CONFIG_SYS_TEXT_BASE 0x00110000 /* * Memory layout for where various images get loaded by boot scripts: diff --git a/include/configs/tegra210-common.h b/include/configs/tegra210-common.h index e6c815212d..8f35a7bf3d 100644 --- a/include/configs/tegra210-common.h +++ b/include/configs/tegra210-common.h @@ -26,7 +26,7 @@ /*----------------------------------------------------------------------- * Physical Memory Map */ -#define CONFIG_SYS_TEXT_BASE 0x8010E000 +#define CONFIG_SYS_TEXT_BASE 0x80110000 /* Generic Interrupt Controller */ #define CONFIG_GICV2 diff --git a/include/configs/tegra30-common.h b/include/configs/tegra30-common.h index 3e8e3c1e5b..9afd86484b 100644 --- a/include/configs/tegra30-common.h +++ b/include/configs/tegra30-common.h @@ -31,7 +31,7 @@ /*----------------------------------------------------------------------- * Physical Memory Map */ -#define CONFIG_SYS_TEXT_BASE 0x8010E000 +#define CONFIG_SYS_TEXT_BASE 0x80110000 /* * Memory layout for where various images get loaded by boot scripts: diff --git a/include/configs/ti_omap3_common.h b/include/configs/ti_omap3_common.h index be231a5513..e399a879ac 100644 --- a/include/configs/ti_omap3_common.h +++ b/include/configs/ti_omap3_common.h @@ -66,7 +66,7 @@ #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* TWL4030 */ -#define CONFIG_TWL4030_POWER 1 +#define CONFIG_TWL4030_POWER /* SPL */ #define CONFIG_SPL_TEXT_BASE 0x40200800 diff --git a/include/configs/vexpress_aemv8a.h b/include/configs/vexpress_aemv8a.h index 6107c64dd2..ef3014d68b 100644 --- a/include/configs/vexpress_aemv8a.h +++ b/include/configs/vexpress_aemv8a.h @@ -30,7 +30,8 @@ #define CONFIG_BOOTP_VCI_STRING "U-boot.armv8.vexpress_aemv8a" /* Link Definitions */ -#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP +#if defined(CONFIG_TARGET_VEXPRESS64_BASE_FVP) || \ + defined(CONFIG_TARGET_VEXPRESS64_BASE_FVP_DRAM) /* ATF loads u-boot here for BASE_FVP model */ #define CONFIG_SYS_TEXT_BASE 0x88000000 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x03f00000) @@ -41,6 +42,8 @@ #error "Unknown board variant" #endif +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + /* Flat Device Tree Definitions */ #define CONFIG_OF_LIBFDT @@ -101,7 +104,8 @@ #define GICR_BASE (0x2f100000) #else -#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP +#if defined(CONFIG_TARGET_VEXPRESS64_BASE_FVP) || \ + defined(CONFIG_TARGET_VEXPRESS64_BASE_FVP_DRAM) #define GICD_BASE (0x2f000000) #define GICC_BASE (0x2c000000) #elif CONFIG_TARGET_VEXPRESS64_JUNO @@ -183,25 +187,46 @@ * be copied into DRAM */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "kernel_name=Image\0" \ + "kernel_name=norkern\0" \ + "kernel_alt_name=Image\0" \ "kernel_addr=0x80000000\0" \ - "fdt_name=juno\0" \ + "initrd_name=ramdisk.img\0" \ + "initrd_addr=0x84000000\0" \ + "fdt_name=board.dtb\0" \ + "fdt_alt_name=juno\0" \ "fdt_addr=0x83000000\0" \ "fdt_high=0xffffffffffffffff\0" \ "initrd_high=0xffffffffffffffff\0" \ /* Assume we boot with root on the first partition of a USB stick */ #define CONFIG_BOOTARGS "console=ttyAMA0,115200n8 " \ - "root=/dev/sda1 rw " \ + "root=/dev/sda2 rw " \ "rootwait "\ - "earlyprintk=pl011,0x7ff80000 debug user_debug=31 "\ + "earlyprintk=pl011,0x7ff80000 debug "\ + "user_debug=31 "\ + "androidboot.hardware=juno "\ "loglevel=9" /* Copy the kernel and FDT to DRAM memory and boot */ #define CONFIG_BOOTCOMMAND "afs load ${kernel_name} ${kernel_addr} ; " \ + "if test $? -eq 1; then "\ + " echo Loading ${kernel_alt_name} instead of "\ + "${kernel_name}; "\ + " afs load ${kernel_alt_name} ${kernel_addr};"\ + "fi ; "\ "afs load ${fdt_name} ${fdt_addr} ; " \ + "if test $? -eq 1; then "\ + " echo Loading ${fdt_alt_name} instead of "\ + "${fdt_name}; "\ + " afs load ${fdt_alt_name} ${fdt_addr}; "\ + "fi ; "\ "fdt addr ${fdt_addr}; fdt resize; " \ - "booti ${kernel_addr} - ${fdt_addr}" + "if afs load ${initrd_name} ${initrd_addr} ; "\ + "then "\ + " setenv initrd_param ${initrd_addr}; "\ + " else setenv initrd_param -; "\ + "fi ; " \ + "booti ${kernel_addr} ${initrd_param} ${fdt_addr}" #define CONFIG_BOOTDELAY 1 @@ -222,13 +247,33 @@ #define CONFIG_BOOTCOMMAND "smhload ${kernel_name} ${kernel_addr}; " \ "smhload ${fdt_name} ${fdt_addr}; " \ - "smhload ${initrd_name} ${initrd_addr} initrd_end; " \ + "smhload ${initrd_name} ${initrd_addr} "\ + "initrd_end; " \ "fdt addr ${fdt_addr}; fdt resize; " \ "fdt chosen ${initrd_addr} ${initrd_end}; " \ "booti $kernel_addr - $fdt_addr" #define CONFIG_BOOTDELAY 1 +#elif CONFIG_TARGET_VEXPRESS64_BASE_FVP_DRAM +#define CONFIG_EXTRA_ENV_SETTINGS \ + "kernel_addr=0x80080000\0" \ + "initrd_addr=0x84000000\0" \ + "fdt_addr=0x83000000\0" \ + "fdt_high=0xffffffffffffffff\0" \ + "initrd_high=0xffffffffffffffff\0" + +#define CONFIG_BOOTARGS "console=ttyAMA0 earlyprintk=pl011,"\ + "0x1c090000 debug user_debug=31 "\ + "androidboot.hardware=fvpbase "\ + "root=/dev/vda2 rw "\ + "rootwait "\ + "loglevel=9" + +#define CONFIG_BOOTCOMMAND "booti $kernel_addr $initrd_addr $fdt_addr" + +#define CONFIG_BOOTDELAY 1 + #else #error "Unknown board variant" #endif |