diff options
Diffstat (limited to 'include/mvebu_mmc.h')
| -rw-r--r-- | include/mvebu_mmc.h | 278 |
1 files changed, 278 insertions, 0 deletions
diff --git a/include/mvebu_mmc.h b/include/mvebu_mmc.h new file mode 100644 index 0000000000..28d98fe148 --- /dev/null +++ b/include/mvebu_mmc.h @@ -0,0 +1,278 @@ +/* + * Marvell MMC/SD/SDIO driver + * + * (C) Copyright 2012 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Maen Suleiman, Gerald Kerma + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __MVEBU_MMC_H__ +#define __MVEBU_MMC_H__ + +/* needed for the mmc_cfg definition */ +#include <mmc.h> + +#define MMC_BLOCK_SIZE 512 + +/* + * Clock rates + */ + +#define MVEBU_MMC_CLOCKRATE_MAX 50000000 +#define MVEBU_MMC_BASE_DIV_MAX 0x7ff +#define MVEBU_MMC_BASE_FAST_CLOCK CONFIG_SYS_TCLK +#define MVEBU_MMC_BASE_FAST_CLK_100 100000000 +#define MVEBU_MMC_BASE_FAST_CLK_200 200000000 + +/* SDIO register */ +#define SDIO_SYS_ADDR_LOW 0x000 +#define SDIO_SYS_ADDR_HI 0x004 +#define SDIO_BLK_SIZE 0x008 +#define SDIO_BLK_COUNT 0x00c +#define SDIO_ARG_LOW 0x010 +#define SDIO_ARG_HI 0x014 +#define SDIO_XFER_MODE 0x018 +#define SDIO_CMD 0x01c +#define SDIO_RSP(i) (0x020 + ((i)<<2)) +#define SDIO_RSP0 0x020 +#define SDIO_RSP1 0x024 +#define SDIO_RSP2 0x028 +#define SDIO_RSP3 0x02c +#define SDIO_RSP4 0x030 +#define SDIO_RSP5 0x034 +#define SDIO_RSP6 0x038 +#define SDIO_RSP7 0x03c +#define SDIO_BUF_DATA_PORT 0x040 +#define SDIO_RSVED 0x044 +#define SDIO_HW_STATE 0x048 +#define SDIO_PRESENT_STATE0 0x048 +#define SDIO_PRESENT_STATE1 0x04c +#define SDIO_HOST_CTRL 0x050 +#define SDIO_BLK_GAP_CTRL 0x054 +#define SDIO_CLK_CTRL 0x058 +#define SDIO_SW_RESET 0x05c +#define SDIO_NOR_INTR_STATUS 0x060 +#define SDIO_ERR_INTR_STATUS 0x064 +#define SDIO_NOR_STATUS_EN 0x068 +#define SDIO_ERR_STATUS_EN 0x06c +#define SDIO_NOR_INTR_EN 0x070 +#define SDIO_ERR_INTR_EN 0x074 +#define SDIO_AUTOCMD12_ERR_STATUS 0x078 +#define SDIO_CURR_BYTE_LEFT 0x07c +#define SDIO_CURR_BLK_LEFT 0x080 +#define SDIO_AUTOCMD12_ARG_LOW 0x084 +#define SDIO_AUTOCMD12_ARG_HI 0x088 +#define SDIO_AUTOCMD12_INDEX 0x08c +#define SDIO_AUTO_RSP(i) (0x090 + ((i)<<2)) +#define SDIO_AUTO_RSP0 0x090 +#define SDIO_AUTO_RSP1 0x094 +#define SDIO_AUTO_RSP2 0x098 +#define SDIO_CLK_DIV 0x128 + +#define WINDOW_CTRL(i) (0x108 + ((i) << 3)) +#define WINDOW_BASE(i) (0x10c + ((i) << 3)) + +/* SDIO_PRESENT_STATE */ +#define CARD_BUSY (1 << 1) +#define CMD_INHIBIT (1 << 0) +#define CMD_TXACTIVE (1 << 8) +#define CMD_RXACTIVE (1 << 9) +#define CMD_AUTOCMD12ACTIVE (1 << 14) +#define CMD_BUS_BUSY (CMD_AUTOCMD12ACTIVE | \ + CMD_RXACTIVE | \ + CMD_TXACTIVE | \ + CMD_INHIBIT | \ + CARD_BUSY) + +/* + * SDIO_CMD + */ + +#define SDIO_CMD_RSP_NONE (0 << 0) +#define SDIO_CMD_RSP_136 (1 << 0) +#define SDIO_CMD_RSP_48 (2 << 0) +#define SDIO_CMD_RSP_48BUSY (3 << 0) + +#define SDIO_CMD_CHECK_DATACRC16 (1 << 2) +#define SDIO_CMD_CHECK_CMDCRC (1 << 3) +#define SDIO_CMD_INDX_CHECK (1 << 4) +#define SDIO_CMD_DATA_PRESENT (1 << 5) +#define SDIO_UNEXPECTED_RESP (1 << 7) + +#define SDIO_CMD_INDEX(x) ((x) << 8) + +/* + * SDIO_XFER_MODE + */ + +#define SDIO_XFER_MODE_STOP_CLK (1 << 5) +#define SDIO_XFER_MODE_HW_WR_DATA_EN (1 << 1) +#define SDIO_XFER_MODE_AUTO_CMD12 (1 << 2) +#define SDIO_XFER_MODE_INT_CHK_EN (1 << 3) +#define SDIO_XFER_MODE_TO_HOST (1 << 4) +#define SDIO_XFER_MODE_DMA (0 << 6) + +/* + * SDIO_HOST_CTRL + */ + +#define SDIO_HOST_CTRL_PUSH_PULL_EN (1 << 0) + +#define SDIO_HOST_CTRL_CARD_TYPE_MEM_ONLY (0 << 1) +#define SDIO_HOST_CTRL_CARD_TYPE_IO_ONLY (1 << 1) +#define SDIO_HOST_CTRL_CARD_TYPE_IO_MEM_COMBO (2 << 1) +#define SDIO_HOST_CTRL_CARD_TYPE_IO_MMC (3 << 1) +#define SDIO_HOST_CTRL_CARD_TYPE_MASK (3 << 1) + +#define SDIO_HOST_CTRL_BIG_ENDIAN (1 << 3) +#define SDIO_HOST_CTRL_LSB_FIRST (1 << 4) +#define SDIO_HOST_CTRL_DATA_WIDTH_1_BIT (0 << 9) +#define SDIO_HOST_CTRL_DATA_WIDTH_4_BITS (1 << 9) +#define SDIO_HOST_CTRL_HI_SPEED_EN (1 << 10) + +#define SDIO_HOST_CTRL_TMOUT_MAX 0xf +#define SDIO_HOST_CTRL_TMOUT_MASK (0xf << 11) +#define SDIO_HOST_CTRL_TMOUT(x) ((x) << 11) +#define SDIO_HOST_CTRL_TMOUT_EN (1 << 15) + +/* + * SDIO_SW_RESET + */ + +#define SDIO_SW_RESET_NOW (1 << 8) + +/* + * Normal interrupt status bits + */ + +#define SDIO_NOR_ERROR (1 << 15) +#define SDIO_NOR_UNEXP_RSP (1 << 14) +#define SDIO_NOR_AUTOCMD12_DONE (1 << 13) +#define SDIO_NOR_SUSPEND_ON (1 << 12) +#define SDIO_NOR_LMB_FF_8W_AVAIL (1 << 11) +#define SDIO_NOR_LMB_FF_8W_FILLED (1 << 10) +#define SDIO_NOR_READ_WAIT_ON (1 << 9) +#define SDIO_NOR_CARD_INT (1 << 8) +#define SDIO_NOR_READ_READY (1 << 5) +#define SDIO_NOR_WRITE_READY (1 << 4) +#define SDIO_NOR_DMA_INI (1 << 3) +#define SDIO_NOR_BLK_GAP_EVT (1 << 2) +#define SDIO_NOR_XFER_DONE (1 << 1) +#define SDIO_NOR_CMD_DONE (1 << 0) + +/* + * Error status bits + */ + +#define SDIO_ERR_CRC_STATUS (1 << 14) +#define SDIO_ERR_CRC_STARTBIT (1 << 13) +#define SDIO_ERR_CRC_ENDBIT (1 << 12) +#define SDIO_ERR_RESP_TBIT (1 << 11) +#define SDIO_ERR_XFER_SIZE (1 << 10) +#define SDIO_ERR_CMD_STARTBIT (1 << 9) +#define SDIO_ERR_AUTOCMD12 (1 << 8) +#define SDIO_ERR_DATA_ENDBIT (1 << 6) +#define SDIO_ERR_DATA_CRC (1 << 5) +#define SDIO_ERR_DATA_TIMEOUT (1 << 4) +#define SDIO_ERR_CMD_INDEX (1 << 3) +#define SDIO_ERR_CMD_ENDBIT (1 << 2) +#define SDIO_ERR_CMD_CRC (1 << 1) +#define SDIO_ERR_CMD_TIMEOUT (1 << 0) +/* enable all for polling */ +#define SDIO_POLL_MASK 0xffff + +/* + * CMD12 error status bits + */ + +#define SDIO_AUTOCMD12_ERR_NOTEXE (1 << 0) +#define SDIO_AUTOCMD12_ERR_TIMEOUT (1 << 1) +#define SDIO_AUTOCMD12_ERR_CRC (1 << 2) +#define SDIO_AUTOCMD12_ERR_ENDBIT (1 << 3) +#define SDIO_AUTOCMD12_ERR_INDEX (1 << 4) +#define SDIO_AUTOCMD12_ERR_RESP_T_BIT (1 << 5) +#define SDIO_AUTOCMD12_ERR_RESP_STARTBIT (1 << 6) + +#define MMC_RSP_PRESENT (1 << 0) +/* 136 bit response */ +#define MMC_RSP_136 (1 << 1) +/* expect valid crc */ +#define MMC_RSP_CRC (1 << 2) +/* card may send busy */ +#define MMC_RSP_BUSY (1 << 3) +/* response contains opcode */ +#define MMC_RSP_OPCODE (1 << 4) + +#define MMC_BUSMODE_OPENDRAIN 1 +#define MMC_BUSMODE_PUSHPULL 2 + +#define MMC_BUS_WIDTH_1 0 +#define MMC_BUS_WIDTH_4 2 +#define MMC_BUS_WIDTH_8 3 + +/* Can the host do 4 bit transfers */ +#define MMC_CAP_4_BIT_DATA (1 << 0) +/* Can do MMC high-speed timing */ +#define MMC_CAP_MMC_HIGHSPEED (1 << 1) +/* Can do SD high-speed timing */ +#define MMC_CAP_SD_HIGHSPEED (1 << 2) +/* Can signal pending SDIO IRQs */ +#define MMC_CAP_SDIO_IRQ (1 << 3) +/* Talks only SPI protocols */ +#define MMC_CAP_SPI (1 << 4) +/* Needs polling for card-detection */ +#define MMC_CAP_NEEDS_POLL (1 << 5) +/* Can the host do 8 bit transfers */ +#define MMC_CAP_8_BIT_DATA (1 << 6) + +/* Nonremovable e.g. eMMC */ +#define MMC_CAP_NONREMOVABLE (1 << 8) +/* Waits while card is busy */ +#define MMC_CAP_WAIT_WHILE_BUSY (1 << 9) +/* Allow erase/trim commands */ +#define MMC_CAP_ERASE (1 << 10) +/* can support DDR mode at 1.8V */ +#define MMC_CAP_1_8V_DDR (1 << 11) +/* can support DDR mode at 1.2V */ +#define MMC_CAP_1_2V_DDR (1 << 12) +/* Can power off after boot */ +#define MMC_CAP_POWER_OFF_CARD (1 << 13) +/* CMD14/CMD19 bus width ok */ +#define MMC_CAP_BUS_WIDTH_TEST (1 << 14) +/* Host supports UHS SDR12 mode */ +#define MMC_CAP_UHS_SDR12 (1 << 15) +/* Host supports UHS SDR25 mode */ +#define MMC_CAP_UHS_SDR25 (1 << 16) +/* Host supports UHS SDR50 mode */ +#define MMC_CAP_UHS_SDR50 (1 << 17) +/* Host supports UHS SDR104 mode */ +#define MMC_CAP_UHS_SDR104 (1 << 18) +/* Host supports UHS DDR50 mode */ +#define MMC_CAP_UHS_DDR50 (1 << 19) +/* Host supports Driver Type A */ +#define MMC_CAP_DRIVER_TYPE_A (1 << 23) +/* Host supports Driver Type C */ +#define MMC_CAP_DRIVER_TYPE_C (1 << 24) +/* Host supports Driver Type D */ +#define MMC_CAP_DRIVER_TYPE_D (1 << 25) +/* CMD23 supported. */ +#define MMC_CAP_CMD23 (1 << 30) +/* Hardware reset */ +#define MMC_CAP_HW_RESET (1 << 31) + +struct mvebu_mmc_cfg { + u32 mvebu_mmc_base; + u32 mvebu_mmc_clk; + u8 max_bus_width; + struct mmc_config cfg; +}; + +/* + * Functions prototypes + */ + +int mvebu_mmc_init(bd_t *bis); + +#endif /* __MVEBU_MMC_H__ */ |