diff options
Diffstat (limited to 'include')
93 files changed, 2279 insertions, 365 deletions
diff --git a/include/atmel_hlcdc.h b/include/atmel_hlcdc.h index 945b30acb0..fbd2f92457 100644 --- a/include/atmel_hlcdc.h +++ b/include/atmel_hlcdc.h @@ -217,6 +217,13 @@ struct atmel_hlcd_regs { #define LCDC_BASECFG3_RDEF(value) \ ((LCDC_BASECFG3_RDEF_Msk & ((value) << LCDC_BASECFG3_RDEF_Pos))) +#define LCDC_BASECLUT_BCLUT_Pos 0 +#define LCDC_BASECLUT_BCLUT_Msk (0xff << LCDC_BASECLUT_BCLUT_Pos) +#define LCDC_BASECLUT_GCLUT_Pos 8 +#define LCDC_BASECLUT_GCLUT_Msk (0xff << LCDC_BASECLUT_GCLUT_Pos) +#define LCDC_BASECLUT_RCLUT_Pos 16 +#define LCDC_BASECLUT_RCLUT_Msk (0xff << LCDC_BASECLUT_RCLUT_Pos) + #define LCDC_BASECFG4_DMA (0x1 << 8) #define LCDC_BASECFG4_REP (0x1 << 9) diff --git a/include/bouncebuf.h b/include/bouncebuf.h index 31021c5b85..707b588c73 100644 --- a/include/bouncebuf.h +++ b/include/bouncebuf.h @@ -25,6 +25,8 @@ #ifndef __INCLUDE_BOUNCEBUF_H__ #define __INCLUDE_BOUNCEBUF_H__ +#include <linux/types.h> + /* * GEN_BB_READ -- Data are read from the buffer eg. by DMA hardware. * The source buffer is copied into the bounce buffer (if unaligned, otherwise @@ -51,37 +53,36 @@ */ #define GEN_BB_RW (GEN_BB_READ | GEN_BB_WRITE) -#ifdef CONFIG_BOUNCE_BUFFER +struct bounce_buffer { + /* Copy of data parameter passed to start() */ + void *user_buffer; + /* + * DMA-aligned buffer. This field is always set to the value that + * should be used for DMA; either equal to .user_buffer, or to a + * freshly allocated aligned buffer. + */ + void *bounce_buffer; + /* Copy of len parameter passed to start() */ + size_t len; + /* DMA-aligned buffer length */ + size_t len_aligned; + /* Copy of flags parameter passed to start() */ + unsigned int flags; +}; + /** * bounce_buffer_start() -- Start the bounce buffer session + * state: stores state passed between bounce_buffer_{start,stop} * data: pointer to buffer to be aligned * len: length of the buffer - * backup: pointer to backup buffer (the original value is stored here if - * needed * flags: flags describing the transaction, see above. */ -int bounce_buffer_start(void **data, size_t len, void **backup, uint8_t flags); +int bounce_buffer_start(struct bounce_buffer *state, void *data, + size_t len, unsigned int flags); /** * bounce_buffer_stop() -- Finish the bounce buffer session - * data: pointer to buffer that was aligned - * len: length of the buffer - * backup: pointer to backup buffer (the original value is stored here if - * needed - * flags: flags describing the transaction, see above. + * state: stores state passed between bounce_buffer_{start,stop} */ -int bounce_buffer_stop(void **data, size_t len, void **backup, uint8_t flags); -#else -static inline int bounce_buffer_start(void **data, size_t len, void **backup, - uint8_t flags) -{ - return 0; -} - -static inline int bounce_buffer_stop(void **data, size_t len, void **backup, - uint8_t flags) -{ - return 0; -} -#endif +int bounce_buffer_stop(struct bounce_buffer *state); #endif diff --git a/include/cbfs.h b/include/cbfs.h index 6ea3f35119..5bb12c355c 100644 --- a/include/cbfs.h +++ b/include/cbfs.h @@ -1,9 +1,6 @@ /* * Copyright (c) 2011 The Chromium OS Authors. All rights reserved. * - * See file CREDITS for list of people who contributed to this - * project. - * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of @@ -77,46 +74,47 @@ struct cbfs_cachenode { extern enum cbfs_result file_cbfs_result; -/* - * Return a string describing the most recent error condition. +/** + * file_cbfs_error() - Return a string describing the most recent error + * condition. * * @return A pointer to the constant string. */ const char *file_cbfs_error(void); -/* - * Initialize the CBFS driver and load metadata into RAM. +/** + * file_cbfs_init() - Initialize the CBFS driver and load metadata into RAM. * - * @param end_of_rom Points to the end of the ROM the CBFS should be read + * @end_of_rom: Points to the end of the ROM the CBFS should be read * from. */ void file_cbfs_init(uintptr_t end_of_rom); -/* - * Get the header structure for the current CBFS. +/** + * file_cbfs_get_header() - Get the header structure for the current CBFS. * * @return A pointer to the constant structure, or NULL if there is none. */ const struct cbfs_header *file_cbfs_get_header(void); -/* - * Get a handle for the first file in CBFS. +/** + * file_cbfs_get_first() - Get a handle for the first file in CBFS. * * @return A handle for the first file in CBFS, NULL on error. */ const struct cbfs_cachenode *file_cbfs_get_first(void); -/* - * Get a handle to the file after this one in CBFS. +/** + * file_cbfs_get_next() - Get a handle to the file after this one in CBFS. * - * @param file A pointer to the handle to advance. + * @file: A pointer to the handle to advance. */ void file_cbfs_get_next(const struct cbfs_cachenode **file); -/* - * Find a file with a particular name in CBFS. +/** + * file_cbfs_find() - Find a file with a particular name in CBFS. * - * @param name The name to search for. + * @name: The name to search for. * * @return A handle to the file, or NULL on error. */ @@ -127,53 +125,55 @@ const struct cbfs_cachenode *file_cbfs_find(const char *name); /* All of the functions below can be used without first initializing CBFS. */ /***************************************************************************/ -/* - * Find a file with a particular name in CBFS without using the heap. +/** + * file_cbfs_find_uncached() - Find a file with a particular name in CBFS + * without using the heap. * - * @param end_of_rom Points to the end of the ROM the CBFS should be read + * @end_of_rom: Points to the end of the ROM the CBFS should be read * from. - * @param name The name to search for. + * @name: The name to search for. * * @return A handle to the file, or NULL on error. */ const struct cbfs_cachenode *file_cbfs_find_uncached(uintptr_t end_of_rom, const char *name); -/* - * Get the name of a file in CBFS. +/** + * file_cbfs_name() - Get the name of a file in CBFS. * - * @param file The handle to the file. + * @file: The handle to the file. * * @return The name of the file, NULL on error. */ const char *file_cbfs_name(const struct cbfs_cachenode *file); -/* - * Get the size of a file in CBFS. +/** + * file_cbfs_size() - Get the size of a file in CBFS. * - * @param file The handle to the file. + * @file: The handle to the file. * * @return The size of the file, zero on error. */ u32 file_cbfs_size(const struct cbfs_cachenode *file); -/* - * Get the type of a file in CBFS. +/** + * file_cbfs_type() - Get the type of a file in CBFS. * - * @param file The handle to the file. + * @file: The handle to the file. * * @return The type of the file, zero on error. */ u32 file_cbfs_type(const struct cbfs_cachenode *file); -/* - * Read a file from CBFS into RAM +/** + * file_cbfs_read() - Read a file from CBFS into RAM * - * @param file A handle to the file to read. - * @param buffer Where to read it into memory. + * @file: A handle to the file to read. + * @buffer: Where to read it into memory. + * @maxsize: Maximum number of bytes to read * * @return If positive or zero, the number of characters read. If negative, an - * error occurred. + * error occurred. */ long file_cbfs_read(const struct cbfs_cachenode *file, void *buffer, unsigned long maxsize); diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h index 9ecdad9c97..e3e5ebc53c 100644 --- a/include/configs/CPCI405.h +++ b/include/configs/CPCI405.h @@ -174,7 +174,7 @@ #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */ #define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */ diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h index efab11991d..c4fff486d8 100644 --- a/include/configs/CPCI4052.h +++ b/include/configs/CPCI4052.h @@ -195,7 +195,7 @@ #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */ #define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */ diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h index 83e9a046ad..9122cbd877 100644 --- a/include/configs/CPCI405AB.h +++ b/include/configs/CPCI405AB.h @@ -192,7 +192,7 @@ #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */ #define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */ diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h index 1944a071b4..f778af7e36 100644 --- a/include/configs/CPCI405DT.h +++ b/include/configs/CPCI405DT.h @@ -196,7 +196,7 @@ #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */ #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */ -#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2PCI (bd->bi_memsize) /* host use this pci address */ #define CONFIG_PCI_4xx_PTM_OVERWRITE 1 /* overwrite PTMx settings by env */ diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h index 57aef21e96..437ee6ee6b 100644 --- a/include/configs/P1010RDB.h +++ b/include/configs/P1010RDB.h @@ -553,6 +553,7 @@ extern unsigned long get_sdram_size(void); /* SATA */ #define CONFIG_FSL_SATA +#define CONFIG_FSL_SATA_V2 #define CONFIG_LIBATA #ifdef CONFIG_FSL_SATA diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h index b3c850d584..14d597aad2 100644 --- a/include/configs/P1022DS.h +++ b/include/configs/P1022DS.h @@ -360,6 +360,7 @@ /* SATA */ #define CONFIG_LIBATA #define CONFIG_FSL_SATA +#define CONFIG_FSL_SATA_V2 #define CONFIG_SYS_SATA_MAX_DEVICE 2 #define CONFIG_SATA1 diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h index 800d666ab2..878bd5fa5e 100644 --- a/include/configs/P1023RDS.h +++ b/include/configs/P1023RDS.h @@ -524,7 +524,7 @@ extern unsigned long get_clock_freq(void); /* Default address of microcode for the Linux Fman driver */ /* QE microcode/firmware address */ #define CONFIG_SYS_QE_FMAN_FW_IN_NOR -#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEF000000 +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 #else #define CONFIG_SYS_QE_FMAN_FW_IN_NAND #define CONFIG_SYS_QE_FMAN_FW_ADDR 0x1f00000 diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index 5cdb628ab1..8b9b0dbc22 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -202,15 +202,21 @@ unsigned long get_board_sys_clk(unsigned long dummy); /* Set the local bus clock 1/8 of platform clock */ #define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 -#define CONFIG_SYS_FLASH_BASE 0xe8000000 /* Start of PromJet */ +/* + * This board doesn't have a promjet connector. + * However, it uses commone corenet board LAW and TLB. + * It is necessary to use the same start address with proper offset. + */ +#define CONFIG_SYS_FLASH_BASE 0xe0000000 #ifdef CONFIG_PHYS_64BIT -#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe8000000ull +#define CONFIG_SYS_FLASH_BASE_PHYS 0xfe0000000ull #else #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE #endif #define CONFIG_SYS_FLASH_BR_PRELIM \ - (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V) + (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \ + BR_PS_16 | BR_V) #define CONFIG_SYS_FLASH_OR_PRELIM \ ((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \ | OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR) @@ -294,7 +300,7 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_FLASH_EMPTY_INFO #define CONFIG_SYS_FLASH_AMD_CHECK_DQ7 -#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000} #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ @@ -539,7 +545,7 @@ unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 #else #define CONFIG_SYS_QE_FMAN_FW_IN_NOR -#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEF000000 +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 #endif #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) @@ -560,8 +566,10 @@ unsigned long get_board_sys_clk(unsigned long dummy); #endif /* CONFIG_PCI */ /* SATA */ +#define CONFIG_FSL_SATA_V2 + +#ifdef CONFIG_FSL_SATA_V2 #define CONFIG_FSL_SATA -#ifdef CONFIG_FSL_SATA #define CONFIG_LIBATA #define CONFIG_SYS_SATA_MAX_DEVICE 2 diff --git a/include/configs/P3041DS.h b/include/configs/P3041DS.h index cf184e74ab..ce8f9b0b2e 100644 --- a/include/configs/P3041DS.h +++ b/include/configs/P3041DS.h @@ -32,6 +32,7 @@ #define CONFIG_MMC #define CONFIG_NAND_FSL_ELBC +#define CONFIG_FSL_SATA_V2 #define CONFIG_PCIE3 #define CONFIG_PCIE4 #define CONFIG_SYS_DPAA_RMAN diff --git a/include/configs/P5020DS.h b/include/configs/P5020DS.h index 7018d7a322..778230d335 100644 --- a/include/configs/P5020DS.h +++ b/include/configs/P5020DS.h @@ -32,6 +32,7 @@ #define CONFIG_MMC #define CONFIG_NAND_FSL_ELBC +#define CONFIG_FSL_SATA_V2 #define CONFIG_PCIE3 #define CONFIG_PCIE4 #define CONFIG_SYS_FSL_RAID_ENGINE diff --git a/include/configs/P5040DS.h b/include/configs/P5040DS.h new file mode 100644 index 0000000000..50d9e541a8 --- /dev/null +++ b/include/configs/P5040DS.h @@ -0,0 +1,40 @@ +/* + * Copyright 2009-2011 Freescale Semiconductor, Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * P5040 DS board configuration file + * + */ +#define CONFIG_P5040DS +#define CONFIG_PHYS_64BIT +#define CONFIG_PPC_P5040 + +#define CONFIG_FSL_NGPIXIS /* use common ngPIXIS code */ + +#define CONFIG_MMC +#define CONFIG_NAND_FSL_ELBC +#define CONFIG_PCIE3 +#define CONFIG_SYS_FSL_RAID_ENGINE + +#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ + +#include "corenet_ds.h" diff --git a/include/configs/PK1C20.h b/include/configs/PK1C20.h index 403fafa2f5..aced85b660 100644 --- a/include/configs/PK1C20.h +++ b/include/configs/PK1C20.h @@ -142,6 +142,7 @@ *----------------------------------------------------------------------*/ #define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */ #define CONFIG_STATUS_LED /* Enable status driver */ +#define CONFIG_BOARD_SPECIFIC_LED #define STATUS_LED_BIT 1 /* Bit-0 on PIO */ #define STATUS_LED_STATE 1 /* Blinking */ diff --git a/include/configs/a3m071.h b/include/configs/a3m071.h new file mode 100644 index 0000000000..df3b4ae90a --- /dev/null +++ b/include/configs/a3m071.h @@ -0,0 +1,380 @@ +/* + * Copyright 2012 Stefan Roese <sr@denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC5200 +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_A3M071 /* ... on A3M071 board */ +#define CONFIG_MPC5200_DDR /* ... use DDR RAM */ + +#define CONFIG_SYS_TEXT_BASE 0x01000000 /* boot low for 32 MiB boards */ + +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33MHz */ + +#define CONFIG_MISC_INIT_R +#define CONFIG_SYS_LOWBOOT /* Enable lowboot */ + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE \ + { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_BSP +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DATE +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_REGINFO + +/* + * IPB Bus clocking configuration. + */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ +/* define for 66MHz speed - undef for 33MHz PCI clock speed */ +#undef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + +/* maximum size of the flat tree (8K) */ +#define OF_FLAT_TREE_MAX_SIZE 8192 + +#define OF_CPU "PowerPC,5200@0" +#define OF_SOC "soc5200@f0000000" +#define OF_TBCLK (bd->bi_busfreq / 4) +#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000" + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ + +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* + * EEPROM configuration + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x53 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* + * RTC configuration + */ +#define CONFIG_RTC_PCF8563 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 + +/* + * NOR flash configuration + */ +#define CONFIG_SYS_FLASH_BASE 0xfc000000 +#define CONFIG_SYS_FLASH_SIZE 0x01000000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_MAX_FLASH_SECT 256 +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 +#define CONFIG_SYS_FLASH_LOCK_TOUT 5 +#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 +#define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_SECT_SIZE 0x20000 +#define CONFIG_ENV_OVERWRITE + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xf0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 + +/* Use SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE + + +#define CONFIG_SYS_GBL_DATA_SIZE 128 +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \ + CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) +#define CONFIG_SYS_MALLOC_LEN (1 << 20) +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC +#define CONFIG_MPC5xxx_FEC_MII100 +#define CONFIG_PHY_ADDR 0x00 + +/* + * GPIO configuration + */ + +/* + * GPIO-config depends on failsave-level + * failsave 0 means just MPX-config, no digiboard, no fpga + * 1 means digiboard ok + * 2 means fpga ok + */ + +/* for failsave-level 0 - full failsave */ +#define CONFIG_SYS_GPS_PORT_CONFIG 0x1005C005 +/* for failsave-level 1 - only digiboard ok */ +#define CONFIG_SYS_GPS_PORT_CONFIG_1 0x1005C005 +/* for failsave-level 2 - all ok */ +#define CONFIG_SYS_GPS_PORT_CONFIG_2 0x1005C005 + +/* + * Configuration matrix + * MSB LSB + * failsave 0 0x1005C005 00010000000001011100000001100101 ( full failsave ) + * failsave 1 0x1005C005 00010000000001011100000001100101 ( digib.-ver ok ) + * failsave 2 0x1005C005 00010000000001011100000001100101 ( all ok ) + * || ||| || | ||| | | | | + * || ||| || | ||| | | | | bit rev name + * ++-+++-++--+---+++-+---+---+---+- 0 31 CS1 + * +-+++-++--+---+++-+---+---+---+- 1 30 LPTZ + * ||| || | ||| | | | | 2 29 ALTs + * +++-++--+---+++-+---+---+---+- 3 28 ALTs + * ++-++--+---+++-+---+---+---+- 4 27 CS7 + * +-++--+---+++-+---+---+---+- 5 26 CS6 + * || | ||| | | | | 6 25 ATA + * ++--+---+++-+---+---+---+- 7 24 ATA + * +--+---+++-+---+---+---+- 8 23 IR_USB_CLK + * | ||| | | | | 9 22 IRDA + * | ||| | | | | 10 21 IRDA + * +---+++-+---+---+---+- 11 20 IRDA + * ||| | | | | 12 19 Ether + * ||| | | | | 13 18 Ether + * ||| | | | | 14 17 Ether + * +++-+---+---+---+- 15 16 Ether + * ++-+---+---+---+- 16 15 PCI_DIS + * +-+---+---+---+- 17 14 USB_SE + * | | | | 18 13 USB + * +---+---+---+- 19 12 USB + * | | | 20 11 PSC3 + * | | | 21 10 PSC3 + * | | | 22 9 PSC3 + * +---+---+- 23 8 PSC3 + * | | 24 7 - + * | | 25 6 PSC2 + * | | 26 5 PSC2 + * +---+- 27 4 PSC2 + * | 28 3 - + * | 29 2 PSC1 + * | 30 1 PSC1 + * +- 31 0 PSC1 + */ + + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "=> " + +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 +#else +#define CONFIG_SYS_CBSIZE 256 +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_MEMTEST_START 0x00100000 +#define CONFIG_SYS_MEMTEST_END 0x00f00000 + +#define CONFIG_SYS_LOAD_ADDR 0x00100000 + +#define CONFIG_SYS_HZ 1000 +#define CONFIG_LOOPW +#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup*/ + +/* + * Various low-level settings + */ +#define CONFIG_SYS_HID0_INIT (HID0_ICE | HID0_ICFI) +#define CONFIG_SYS_HID0_FINAL HID0_ICE + +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_CS2_START 0xe0000000 +#define CONFIG_SYS_CS2_SIZE 0x00100000 + +/* FPGA slave io (512kiB) - see ticket #66 */ +#define CONFIG_SYS_CS3_START 0xE9000000 +#define CONFIG_SYS_CS3_SIZE 0x00080000 +/* 00000000 00110010 1 0 1 1 10 01 00 00 0 0 0 0 = 0x0032B900 */ +#define CONFIG_SYS_CS3_CFG 0x0032B900 + +/* Diagnosis Interface - see ticket #63 */ +#define CONFIG_SYS_CS4_START 0xEA000000 +#define CONFIG_SYS_CS4_SIZE 0x00000001 +/* 00000000 00000010 1 0 1 1 10 01 00 00 0 0 0 0 = 0x0002B900 */ +#define CONFIG_SYS_CS4_CFG 0x0002B900 + +/* FPGA master io (64kiB) - see ticket #66 */ +#define CONFIG_SYS_CS5_START 0xE8000000 +#define CONFIG_SYS_CS5_SIZE 0x00010000 +/* 00000000 00110010 1 0 1 1 10 01 00 00 0 0 0 0 = 0x0032B900 */ +#define CONFIG_SYS_CS5_CFG 0x0032B900 + +#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* for pci_clk = 66 MHz */ +#define CONFIG_SYS_BOOTCS_CFG 0x0006F900 +#define CONFIG_SYS_CS1_CFG 0x0004FB00 +#define CONFIG_SYS_CS2_CFG 0x0006F90C +#else /* for pci_clk = 33 MHz */ +#define CONFIG_SYS_BOOTCS_CFG 0x0002F900 +#define CONFIG_SYS_CS1_CFG 0x0001FB00 +#define CONFIG_SYS_CS2_CFG 0x0002F90C +#endif + +#define CONFIG_SYS_CS_BURST 0x00000000 +/* set DC for FPGA CS5 and CS3 to 0 - see ticket #66 */ +/* R 7 R 6 R 5 R 4 R 3 R 2 R 1 R 0 */ +/* 00 11 00 11 00 00 00 11 00 00 00 00 00 00 00 00 */ +#define CONFIG_SYS_CS_DEADCYCLE 0x33030000 + +#define CONFIG_SYS_RESET_ADDRESS 0xff000000 + +/* + * Environment Configuration + */ + +#define CONFIG_BOOTDELAY 0 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS +#define CONFIG_ZERO_BOOTDELAY_CHECK + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_mtd\" to boot from flash with mtd filesystem;" \ + "echo Type \"run net_nfs\" to boot from tftp with nfs filesystem;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_SYS_OS_BASE 0xfc080000 +#define CONFIG_SYS_FDT_BASE 0xfc060000 + +#define xstr(s) str(s) +#define str(s) #s + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "verify=no\0" \ + "consoledev=ttyPSC0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "mtdargs=setenv bootargs root=/dev/mtdblock4 rw rootfstype=jffs2\0"\ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} " \ + "console=${consoledev},${baudrate}\0" \ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr} - ${fdtaddr}\0" \ + "flash_mtd=run mtdargs addip addtty;" \ + "bootm ${kernel_addr} - ${fdtaddr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdtaddr}\0" \ + "net_nfs=sleep 2; tftp ${loadaddr} ${bootfile};" \ + "tftp c00000 ${fdtfile};" \ + "run nfsargs addip addtty;" \ + "bootm ${loadaddr} - c00000\0" \ + "load=tftp ${loadaddr} u-boot.bin\0" \ + "update=protect off fc000000 fc03ffff; " \ + "era fc000000 fc03ffff; cp.b ${loadaddr} fc000000 40000\0"\ + "upd=run load;run update\0" \ + "fdtaddr=" xstr(CONFIG_SYS_FDT_BASE) "\0" \ + "fdtfile=dtbFile\0" \ + "kernel_addr=" xstr(CONFIG_SYS_OS_BASE) "\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run flash_mtd" + +/* + * SPL related defines + */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_NOR_SUPPORT +#define CONFIG_SPL_TEXT_BASE 0xfc000000 +#define CONFIG_SPL_START_S_PATH "arch/powerpc/cpu/mpc5xxx" +#define CONFIG_SPL_LDSCRIPT "arch/powerpc/cpu/mpc5xxx/u-boot-spl.lds" +#define CONFIG_SPL_LIBCOMMON_SUPPORT /* image.c */ +#define CONFIG_SPL_LIBGENERIC_SUPPORT /* string.c */ +#define CONFIG_SPL_SERIAL_SUPPORT + +/* Place BSS for SPL near end of SDRAM */ +#define CONFIG_SPL_BSS_START_ADDR ((128 - 1) << 20) +#define CONFIG_SPL_BSS_MAX_SIZE (64 << 10) + +#define CONFIG_SPL_OS_BOOT +/* Place patched DT blob (fdt) at this address */ +#define CONFIG_SYS_SPL_ARGS_ADDR 0x01800000 + +/* Settings for real U-Boot to be loaded from NOR flash */ +#ifndef __ASSEMBLY__ +extern char __spl_flash_end[]; +#endif +#define CONFIG_SYS_UBOOT_BASE __spl_flash_end +#define CONFIG_SYS_SPL_MAX_LEN (32 << 10) +#define CONFIG_SYS_UBOOT_START 0x1000100 + +#endif /* __CONFIG_H */ diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index b6e48f8a63..ab9549b93b 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -257,6 +257,33 @@ #define CONFIG_SKIP_LOWLEVEL_INIT #endif +/* + * USB configuration + */ +#define CONFIG_USB_MUSB_DSPS +#define CONFIG_ARCH_MISC_INIT +#define CONFIG_MUSB_GADGET +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_MUSB_HOST +#define CONFIG_AM335X_USB0 +#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL +#define CONFIG_AM335X_USB1 +#define CONFIG_AM335X_USB1_MODE MUSB_HOST + +#ifdef CONFIG_MUSB_HOST +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#endif + +#ifdef CONFIG_MUSB_GADGET +#define CONFIG_USB_ETHER +#define CONFIG_USB_ETH_RNDIS +#endif /* CONFIG_MUSB_GADGET */ + +/* Unsupported features */ +#undef CONFIG_USE_IRQ + #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP #define CONFIG_CMD_PING diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h index 20a3df5db2..e1ad1e58ff 100644 --- a/include/configs/am3517_crane.h +++ b/include/configs/am3517_crane.h @@ -337,6 +337,9 @@ #define CONFIG_SPL_FAT_SUPPORT #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h index ce71d1335c..ba1532540e 100644 --- a/include/configs/am3517_evm.h +++ b/include/configs/am3517_evm.h @@ -97,15 +97,16 @@ /* * USB configuration - * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard - * Enable CONFIG_MUSB_UDC for Device functionalities. + * Enable CONFIG_MUSB_HOST for Host functionalities MSC, keyboard + * Enable CONFIG_MUSB_GADGET for Device functionalities. */ -#define CONFIG_USB_AM35X 1 -#define CONFIG_MUSB_HCD 1 +#define CONFIG_USB_MUSB_AM35X +#define CONFIG_MUSB_HOST +#define CONFIG_MUSB_PIO_ONLY -#ifdef CONFIG_USB_AM35X +#ifdef CONFIG_USB_MUSB_AM35X -#ifdef CONFIG_MUSB_HCD +#ifdef CONFIG_MUSB_HOST #define CONFIG_CMD_USB #define CONFIG_USB_STORAGE @@ -117,21 +118,15 @@ #define CONFIG_PREBOOT "usb start" #endif /* CONFIG_USB_KEYBOARD */ -#endif /* CONFIG_MUSB_HCD */ +#endif /* CONFIG_MUSB_HOST */ -#ifdef CONFIG_MUSB_UDC -/* USB device configuration */ -#define CONFIG_USB_DEVICE 1 -#define CONFIG_USB_TTY 1 -#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 -/* Change these to suit your needs */ -#define CONFIG_USBD_VENDORID 0x0451 -#define CONFIG_USBD_PRODUCTID 0x5678 -#define CONFIG_USBD_MANUFACTURER "Texas Instruments" -#define CONFIG_USBD_PRODUCT_NAME "AM3517EVM" -#endif /* CONFIG_MUSB_UDC */ +#ifdef CONFIG_MUSB_GADGET +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_USB_ETHER +#define CONFIG_USB_ETH_RNDIS +#endif /* CONFIG_MUSB_GADGET */ -#endif /* CONFIG_USB_AM35X */ +#endif /* CONFIG_USB_MUSB_AM35X */ /* commands to include */ #include <config_cmd_default.h> @@ -336,6 +331,9 @@ #define CONFIG_SPL_FAT_SUPPORT #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" diff --git a/include/configs/at91sam9x5ek.h b/include/configs/at91sam9x5ek.h index 71f765b494..131758279c 100644 --- a/include/configs/at91sam9x5ek.h +++ b/include/configs/at91sam9x5ek.h @@ -168,8 +168,7 @@ #define CONFIG_BOOTCOMMAND "nand read " \ "0x22000000 0x200000 0x300000; " \ "bootm 0x22000000" -#else -#ifdef CONFIG_SYS_USE_SPIFLASH +#elif defined(CONFIG_SYS_USE_SPIFLASH) /* bootstrap + u-boot + env + linux in spi flash */ #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_OFFSET 0x5000 @@ -179,14 +178,28 @@ #define CONFIG_BOOTCOMMAND "sf probe 0; " \ "sf read 0x22000000 0x100000 0x300000; " \ "bootm 0x22000000" -#endif +#else /* CONFIG_SYS_USE_MMC */ +/* bootstrap + u-boot + env + linux in mmc */ +#define CONFIG_ENV_IS_IN_MMC +/* For FAT system, most cases it should be in the reserved sector */ +#define CONFIG_ENV_OFFSET 0x2000 +#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_SYS_MMC_ENV_DEV 0 #endif +#ifdef CONFIG_SYS_USE_MMC +#define CONFIG_BOOTARGS "mem=128M console=ttyS0,115200 " \ + "mtdparts=atmel_nand:" \ + "8M(bootstrap/uboot/kernel)ro,-(rootfs) " \ + "root=/dev/mmcblk0p2 " \ + "rw rootfstype=ext4 rootwait" +#else #define CONFIG_BOOTARGS "mem=128M console=ttyS0,115200 " \ "mtdparts=atmel_nand:" \ "8M(bootstrap/uboot/kernel)ro,-(rootfs) " \ "root=/dev/mtdblock1 rw " \ "rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs" +#endif #define CONFIG_BAUDRATE 115200 diff --git a/include/configs/cam_enc_4xx.h b/include/configs/cam_enc_4xx.h index 56dc1cbbd5..a7a698c0ca 100644 --- a/include/configs/cam_enc_4xx.h +++ b/include/configs/cam_enc_4xx.h @@ -219,6 +219,9 @@ #define CONFIG_SPL_BOARD_INIT #define CONFIG_SPL_LIBGENERIC_SUPPORT #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_NAND_SIMPLE #define CONFIG_SYS_NAND_HW_ECC_OOBFIRST #define CONFIG_SPL_SERIAL_SUPPORT diff --git a/include/configs/coreboot.h b/include/configs/coreboot.h index cc95e2be98..adeace0cf2 100644 --- a/include/configs/coreboot.h +++ b/include/configs/coreboot.h @@ -35,9 +35,13 @@ * (easy to change) */ #define CONFIG_SYS_COREBOOT -#undef CONFIG_SHOW_BOOT_PROGRESS +#define CONFIG_SHOW_BOOT_PROGRESS #define CONFIG_LAST_STAGE_INIT - +#define CONFIG_X86_NO_RESET_VECTOR +#define CONFIG_SYS_VSNPRINTF +#define CONFIG_INTEL_CORE_ARCH /* Sandy bridge and ivy bridge chipsets. */ +#define CONFIG_ZBOOT_32 +#define CONFIG_PHYSMEM /*----------------------------------------------------------------------- * Watchdog Configuration @@ -67,11 +71,16 @@ CONFIG_SYS_SCSI_MAX_LUN) #endif +/* Generic TPM interfaced through LPC bus */ +#define CONFIG_GENERIC_LPC_TPM +#define CONFIG_TPM_TIS_BASE_ADDRESS 0xfed40000 + /*----------------------------------------------------------------------- * Real Time Clock Configuration */ #define CONFIG_RTC_MC146818 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0 +#define CONFIG_SYS_ISA_IO CONFIG_SYS_ISA_IO_BASE_ADDRESS /*----------------------------------------------------------------------- * Serial Configuration @@ -88,18 +97,18 @@ #define CONFIG_SYS_NS16550_COM2 UART1_BASE #define CONFIG_SYS_NS16550_PORT_MAPPED -/* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXBUS 1 -/* max. 1 drive per IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) +#define CONFIG_STD_DEVICES_SETTINGS "stdin=usbkbd,vga,eserial0\0" \ + "stdout=vga,eserial0,cbmem\0" \ + "stderr=vga,eserial0,cbmem\0" -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_ISA_IO_BASE_ADDRESS -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x01f0 -#define CONFIG_SYS_ATA_IDE1_OFFSET 0x0170 -#define CONFIG_SYS_ATA_DATA_OFFSET 0 -#define CONFIG_SYS_ATA_REG_OFFSET 0 -#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 +#define CONFIG_CONSOLE_MUX +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_SYS_STDIO_DEREGISTER +#define CONFIG_CBMEM_CONSOLE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_COMMAND_HISTORY +#define CONFIG_AUTOCOMPLETE #define CONFIG_SUPPORT_VFAT /************************************************************ @@ -110,19 +119,30 @@ /************************************************************ * DISK Partition support ************************************************************/ +#define CONFIG_EFI_PARTITION #define CONFIG_DOS_PARTITION #define CONFIG_MAC_PARTITION #define CONFIG_ISO_PARTITION /* Experimental */ +#define CONFIG_CMD_PART #define CONFIG_CMD_CBFS #define CONFIG_CMD_EXT4 #define CONFIG_CMD_EXT4_WRITE +#define CONFIG_PARTITION_UUIDS /*----------------------------------------------------------------------- * Video Configuration */ -#undef CONFIG_VIDEO -#undef CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO +#define CONFIG_VIDEO_COREBOOT +#define CONFIG_VIDEO_SW_CURSOR +#define VIDEO_FB_16BPP_WORD_SWAP +#define CONFIG_I8042_KBD +#define CONFIG_CFB_CONSOLE +#define CONFIG_SYS_CONSOLE_INFO_QUIET + +/* x86 GPIOs are accessed through a PCI device */ +#define CONFIG_INTEL_ICH6_GPIO /*----------------------------------------------------------------------- * Command line configuration. @@ -136,6 +156,7 @@ #define CONFIG_CMD_ECHO #undef CONFIG_CMD_FLASH #define CONFIG_CMD_FPGA +#define CONFIG_CMD_GPIO #define CONFIG_CMD_IMI #undef CONFIG_CMD_IMLS #define CONFIG_CMD_IRQ @@ -153,12 +174,19 @@ #define CONFIG_CMD_SETGETDCR #define CONFIG_CMD_SOURCE #define CONFIG_CMD_XIMG -#define CONFIG_CMD_IDE +#define CONFIG_CMD_SCSI + #define CONFIG_CMD_FAT #define CONFIG_CMD_EXT2 +#define CONFIG_CMD_ZBOOT + #define CONFIG_BOOTDELAY 2 -#define CONFIG_BOOTARGS "root=/dev/mtdblock0 console=ttyS0,9600" +#define CONFIG_BOOTARGS \ + "root=/dev/sdb3 init=/sbin/init rootwait ro" +#define CONFIG_BOOTCOMMAND \ + "ext2load scsi 0:3 01000000 /boot/vmlinuz; zboot 01000000" + #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 115200 @@ -210,12 +238,11 @@ * (128kB + Environment Sector Size) malloc pool */ #define CONFIG_SYS_STACK_SIZE (32 * 1024) -#define CONFIG_SYS_INIT_SP_ADDR (256 * 1024 + 16 * 1024) +#define CONFIG_SYS_CAR_ADDR 0x19200000 +#define CONFIG_SYS_CAR_SIZE (16 * 1024) #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_MONITOR_LEN (256 * 1024) #define CONFIG_SYS_MALLOC_LEN (0x20000 + 128 * 1024) -/* Address of temporary Global Data */ -#define CONFIG_SYS_INIT_GD_ADDR (256 * 1024) /* allow to overwrite serial and ethaddr */ @@ -240,4 +267,7 @@ */ #define CONFIG_PCI +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_STD_DEVICES_SETTINGS + #endif /* __CONFIG_H */ diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h index c41b039996..3f42cd9a38 100644 --- a/include/configs/corenet_ds.h +++ b/include/configs/corenet_ds.h @@ -549,7 +549,7 @@ #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 #else #define CONFIG_SYS_QE_FMAN_FW_IN_NOR -#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEF000000 +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 #endif #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index ddd615509f..99b4de7288 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -227,6 +227,9 @@ #define CONFIG_SYS_NAND_ECCBYTES 10 #define CONFIG_SYS_NAND_OOBSIZE 64 #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_NAND_SIMPLE #define CONFIG_SPL_NAND_LOAD #endif diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h index da3263f4f5..83a8b5d59f 100644 --- a/include/configs/devkit8000.h +++ b/include/configs/devkit8000.h @@ -316,6 +316,9 @@ #define CONFIG_SPL_GPIO_SUPPORT #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_MMC_SUPPORT #define CONFIG_SPL_FAT_SUPPORT #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" diff --git a/include/configs/eNET.h b/include/configs/eNET.h index 4b1c21904c..28cf95b778 100644 --- a/include/configs/eNET.h +++ b/include/configs/eNET.h @@ -168,16 +168,10 @@ #define CONFIG_SYS_STACK_SIZE (32 * 1024) #define CONFIG_SYS_CAR_ADDR 0x19200000 #define CONFIG_SYS_CAR_SIZE (16 * 1024) -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_CAR_ADDR + \ - CONFIG_SYS_CAR_SIZE) #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_MONITOR_LEN (256 * 1024) #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SECT_SIZE + \ 128*1024) -/* Address of temporary Global Data */ -#define CONFIG_SYS_INIT_GD_ADDR CONFIG_SYS_CAR_ADDR - - /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE diff --git a/include/configs/eb_cpu5282.h b/include/configs/eb_cpu5282.h index 9ecc10bd1b..5a0d321f73 100644 --- a/include/configs/eb_cpu5282.h +++ b/include/configs/eb_cpu5282.h @@ -38,7 +38,7 @@ #define CONFIG_MCFUART #define CONFIG_SYS_UART_PORT (0) -#define CONFIG_BAUDRATE 9600 +#define CONFIG_BAUDRATE 115200 #undef CONFIG_MONITOR_IS_IN_RAM /* starts uboot direct */ @@ -52,20 +52,24 @@ #define CONFIG_RESET_TO_RETRY #define CONFIG_SPLASH_SCREEN +#define CONFIG_HW_WATCHDOG + +#define CONFIG_STATUS_LED +#define CONFIG_BOARD_SPECIFIC_LED +#define STATUS_LED_ACTIVE 0 +#define STATUS_LED_BIT 0x0008 /* Timer7 GPIO */ +#define STATUS_LED_BOOT 0 +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +#define STATUS_LED_STATE STATUS_LED_OFF + /*----------------------------------------------------------------------* * Configuration for environment * * Environment is in the second sector of the first 256k of flash * *----------------------------------------------------------------------*/ -#ifndef CONFIG_MONITOR_IS_IN_RAM -#define CONFIG_ENV_ADDR 0xF003C000 /* End of 256K */ -#define CONFIG_ENV_SECT_SIZE 0x4000 -#define CONFIG_ENV_IS_IN_FLASH 1 -#else -#define CONFIG_ENV_ADDR 0xFFE04000 -#define CONFIG_ENV_SECT_SIZE 0x2000 +#define CONFIG_ENV_ADDR 0xFF040000 +#define CONFIG_ENV_SECT_SIZE 0x00020000 #define CONFIG_ENV_IS_IN_FLASH 1 -#endif /* * BOOTP options @@ -78,26 +82,24 @@ /* * Command line configuration. */ +#define CONFIG_CMDLINE_EDITING #include <config_cmd_default.h> #undef CONFIG_CMD_LOADB +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_I2C +#define CONFIG_CMD_LED #define CONFIG_CMD_MII #define CONFIG_CMD_NET #define CONFIG_MCFTMR - #define CONFIG_BOOTDELAY 5 -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #define CONFIG_SYS_PROMPT "\nEB+CPU5282> " #define CONFIG_SYS_LONGHELP 1 -#if defined(CONFIG_CMD_KGDB) #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE @@ -112,12 +114,12 @@ /*----------------------------------------------------------------------* * Clock and PLL Configuration * *----------------------------------------------------------------------*/ -#define CONFIG_SYS_HZ 10000000 -#define CONFIG_SYS_CLK 58982400 /* 9,8304MHz * 6 */ +#define CONFIG_SYS_HZ 1000 +#define CONFIG_SYS_CLK 80000000 /* 8MHz * 8 */ -/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */ +/* PLL Configuration: Ext Clock * 8 (see table 9-4 of MCF user manual) */ -#define CONFIG_SYS_MFD 0x01 /* PLL Multiplication Factor Devider */ +#define CONFIG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */ #define CONFIG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */ /*----------------------------------------------------------------------* @@ -135,7 +137,6 @@ #define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE #define MCFFEC_TOUT_LOOP 50000 -#define CONFIG_ETHADDR 00:CF:52:82:EB:01 #define CONFIG_OVERWRITE_ETHADDR_ONCE /*------------------------------------------------------------------------- @@ -151,7 +152,7 @@ *-----------------------------------------------------------------------*/ #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 -#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 #define CONFIG_SYS_GBL_DATA_OFFSET \ (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET @@ -161,12 +162,11 @@ * (Set up by the startup code) * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CONFIG_SYS_SDRAM_BASE1 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE1 16 /* SDRAM size in MB */ - -#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM_BASE1 -#define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_SDRAM_SIZE1 +#define CONFIG_SYS_SDRAM_BASE0 0x00000000 +#define CONFIG_SYS_SDRAM_SIZE0 16 /* SDRAM size in MB */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM_BASE0 +#define CONFIG_SYS_SDRAM_SIZE CONFIG_SYS_SDRAM_SIZE0 /* If M5282 port is fully implemented the monitor base will be behind * the vector table. */ @@ -190,16 +190,24 @@ /*----------------------------------------------------------------------- * FLASH organization */ +#define CONFIG_FLASH_SHOW_PROGRESS 45 #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE #define CONFIG_SYS_INT_FLASH_BASE 0xF0000000 #define CONFIG_SYS_INT_FLASH_ENABLE 0x21 -#define CONFIG_SYS_MAX_FLASH_SECT 35 -#define CONFIG_SYS_MAX_FLASH_BANKS 2 +#define CONFIG_SYS_MAX_FLASH_SECT 128 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 #define CONFIG_SYS_FLASH_ERASE_TOUT 10000000 #define CONFIG_SYS_FLASH_PROTECTION +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_SIZE 16*1024*1024 +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } + /*----------------------------------------------------------------------- * Cache Configuration */ @@ -221,12 +229,16 @@ * Memory bank definitions */ -#define CONFIG_SYS_CS0_BASE 0xFFE00000 +#define CONFIG_SYS_CS0_BASE 0xFF000000 #define CONFIG_SYS_CS0_CTRL 0x00001980 -#define CONFIG_SYS_CS0_MASK 0x001F0001 +#define CONFIG_SYS_CS0_MASK 0x00FF0001 -#define CONFIG_SYS_CS3_BASE 0xE0000000 -#define CONFIG_SYS_CS0_CTRL 0x00001980 +#define CONFIG_SYS_CS2_BASE 0xE0000000 +#define CONFIG_SYS_CS2_CTRL 0x00001980 +#define CONFIG_SYS_CS2_MASK 0x000F0001 + +#define CONFIG_SYS_CS3_BASE 0xE0100000 +#define CONFIG_SYS_CS3_CTRL 0x00001980 #define CONFIG_SYS_CS3_MASK 0x000F0001 /*----------------------------------------------------------------------- @@ -248,24 +260,42 @@ #define CONFIG_SYS_PCDDR 0x0000000 #define CONFIG_SYS_PCDAT 0x0000000 +#define CONFIG_SYS_PASPAR 0x0F0F #define CONFIG_SYS_PEHLPAR 0xC0 #define CONFIG_SYS_PUAPAR 0x0F #define CONFIG_SYS_DDRUA 0x05 #define CONFIG_SYS_PJPAR 0xFF /*----------------------------------------------------------------------- + * I2C + */ + +#define CONFIG_HARD_I2C +#define CONFIG_FSL_I2C + +#define CONFIG_SYS_I2C_OFFSET 0x00000300 +#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR + +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 0 + +#ifdef CONFIG_CMD_DATE +#define CONFIG_RTC_DS1338 +#define CONFIG_I2C_RTC_ADDR 0x68 +#endif + +/*----------------------------------------------------------------------- * VIDEO configuration */ #define CONFIG_VIDEO #ifdef CONFIG_VIDEO -#define CONFIG_VIDEO_VCXK 1 +#define CONFIG_VIDEO_VCXK 1 #define CONFIG_SYS_VCXK_DEFAULT_LINEALIGN 2 #define CONFIG_SYS_VCXK_DOUBLEBUFFERED 1 -#define CONFIG_SYS_VCXK_BASE CONFIG_SYS_CS3_BASE -#define CONFIG_SYS_VCXK_AUTODETECT 1 +#define CONFIG_SYS_VCXK_BASE CONFIG_SYS_CS2_BASE #define CONFIG_SYS_VCXK_ACKNOWLEDGE_PORT MCFGPTB_GPTPORT #define CONFIG_SYS_VCXK_ACKNOWLEDGE_DDR MCFGPTB_GPTDDR diff --git a/include/configs/hawkboard.h b/include/configs/hawkboard.h index c0e3ed3efc..8d27590278 100644 --- a/include/configs/hawkboard.h +++ b/include/configs/hawkboard.h @@ -63,6 +63,9 @@ #define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_BOARD_INIT #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_NAND_SIMPLE #define CONFIG_SPL_LIBGENERIC_SUPPORT /* for udelay and __div64_32 for NAND */ #define CONFIG_SPL_SERIAL_SUPPORT diff --git a/include/configs/ib62x0.h b/include/configs/ib62x0.h index 85856f290e..f646ae5776 100644 --- a/include/configs/ib62x0.h +++ b/include/configs/ib62x0.h @@ -1,7 +1,7 @@ /* * Copyright (C) 2011-2012 * Gerald Kerma <dreagle@doukki.net> - * Luka Perkov <uboot@lukaperkov.net> + * Luka Perkov <luka@openwrt.org> * * See file CREDITS for list of people who contributed to this * project. diff --git a/include/configs/iconnect.h b/include/configs/iconnect.h index 2b523c9fc9..ba57849a60 100644 --- a/include/configs/iconnect.h +++ b/include/configs/iconnect.h @@ -1,7 +1,7 @@ /* * (C) Copyright 2009-2012 * Wojciech Dubowik <wojciech.dubowik@neratec.com> - * Luka Perkov <uboot@lukaperkov.net> + * Luka Perkov <luka@openwrt.org> * * See file CREDITS for list of people who contributed to this * project. diff --git a/include/configs/igep00x0.h b/include/configs/igep00x0.h index c81ab7622e..be7937d70e 100644 --- a/include/configs/igep00x0.h +++ b/include/configs/igep00x0.h @@ -338,6 +338,9 @@ #ifdef CONFIG_BOOT_NAND #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC /* NAND boot config */ #define CONFIG_SYS_NAND_5_ADDR_CYCLE diff --git a/include/configs/imx31_litekit.h b/include/configs/imx31_litekit.h index 6ae764a2d4..8fc3942450 100644 --- a/include/configs/imx31_litekit.h +++ b/include/configs/imx31_litekit.h @@ -72,9 +72,9 @@ #define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH) /* PMIC Controller */ -#define CONFIG_PMIC -#define CONFIG_PMIC_SPI -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_SPI +#define CONFIG_POWER_FSL #define CONFIG_FSL_PMIC_BUS 1 #define CONFIG_FSL_PMIC_CS 0 #define CONFIG_FSL_PMIC_CLK 1000000 diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 2d33ebcd71..2ebcd1615f 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -401,7 +401,6 @@ #define CONFIG_USB_EHCI /* Enable EHCI USB support */ #define CONFIG_USB_EHCI_PPC4XX /* on PPC4xx platform */ #define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300 -#define CONFIG_EHCI_DCACHE /* with dcache handling support */ #define CONFIG_EHCI_MMIO_BIG_ENDIAN #define CONFIG_EHCI_DESC_BIG_ENDIAN #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* re-init HCD after CMD_RESET */ diff --git a/include/configs/mcx.h b/include/configs/mcx.h index bf49cc1381..e304c99417 100644 --- a/include/configs/mcx.h +++ b/include/configs/mcx.h @@ -114,7 +114,6 @@ #define CONFIG_USB_EHCI_OMAP #define CONFIG_USB_ULPI #define CONFIG_USB_ULPI_VIEWPORT_OMAP -/*#define CONFIG_EHCI_DCACHE*/ /* leave it disabled for now */ #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 57 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 @@ -379,6 +378,9 @@ #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h index 9d9f4a7822..9e4006b441 100644 --- a/include/configs/mx31ads.h +++ b/include/configs/mx31ads.h @@ -68,9 +68,9 @@ #define CONFIG_MXC_GPIO /* PMIC Controller */ -#define CONFIG_PMIC -#define CONFIG_PMIC_SPI -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_SPI +#define CONFIG_POWER_FSL #define CONFIG_FSL_PMIC_BUS 1 #define CONFIG_FSL_PMIC_CS 0 #define CONFIG_FSL_PMIC_CLK 1000000 diff --git a/include/configs/mx31pdk.h b/include/configs/mx31pdk.h index 6572676970..138a941373 100644 --- a/include/configs/mx31pdk.h +++ b/include/configs/mx31pdk.h @@ -69,9 +69,9 @@ #define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH) /* PMIC Controller */ -#define CONFIG_PMIC -#define CONFIG_PMIC_SPI -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_SPI +#define CONFIG_POWER_FSL #define CONFIG_FSL_PMIC_BUS 1 #define CONFIG_FSL_PMIC_CS 2 #define CONFIG_FSL_PMIC_CLK 1000000 diff --git a/include/configs/mx35pdk.h b/include/configs/mx35pdk.h index 1c2f5993d8..88b2bd6ed4 100644 --- a/include/configs/mx35pdk.h +++ b/include/configs/mx35pdk.h @@ -65,9 +65,9 @@ /* * PMIC Configs */ -#define CONFIG_PMIC -#define CONFIG_PMIC_I2C -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_FSL #define CONFIG_PMIC_FSL_MC13892 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x08 #define CONFIG_RTC_MC13XXX diff --git a/include/configs/mx51_efikamx.h b/include/configs/mx51_efikamx.h index a056566efc..a74a0a71f1 100644 --- a/include/configs/mx51_efikamx.h +++ b/include/configs/mx51_efikamx.h @@ -127,9 +127,9 @@ #endif /* SPI PMIC */ -#define CONFIG_PMIC -#define CONFIG_PMIC_SPI -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_SPI +#define CONFIG_POWER_FSL #define CONFIG_FSL_PMIC_BUS 0 #define CONFIG_FSL_PMIC_CS (0 | 120 << 8) #define CONFIG_FSL_PMIC_CLK 25000000 diff --git a/include/configs/mx51evk.h b/include/configs/mx51evk.h index 4e82355334..fa0db3824b 100644 --- a/include/configs/mx51evk.h +++ b/include/configs/mx51evk.h @@ -69,9 +69,9 @@ #define CONFIG_MXC_SPI /* PMIC Controller */ -#define CONFIG_PMIC -#define CONFIG_PMIC_SPI -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_SPI +#define CONFIG_POWER_FSL #define CONFIG_FSL_PMIC_BUS 0 #define CONFIG_FSL_PMIC_CS 0 #define CONFIG_FSL_PMIC_CLK 2500000 diff --git a/include/configs/mx53evk.h b/include/configs/mx53evk.h index c472075c9a..a0af3eeb26 100644 --- a/include/configs/mx53evk.h +++ b/include/configs/mx53evk.h @@ -55,9 +55,9 @@ #define CONFIG_SYS_I2C_SPEED 100000 /* PMIC Configs */ -#define CONFIG_PMIC -#define CONFIG_PMIC_I2C -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_FSL #define CONFIG_SYS_FSL_PMIC_I2C_ADDR 8 #define CONFIG_PMIC_FSL_MC13892 #define CONFIG_RTC_MC13XXX diff --git a/include/configs/mx53loco.h b/include/configs/mx53loco.h index 37f9d69e26..e30502b4e2 100644 --- a/include/configs/mx53loco.h +++ b/include/configs/mx53loco.h @@ -89,10 +89,10 @@ #define CONFIG_SYS_I2C_SPEED 100000 /* PMIC Controller */ -#define CONFIG_PMIC -#define CONFIG_PMIC_I2C -#define CONFIG_DIALOG_PMIC -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_DIALOG_POWER +#define CONFIG_POWER_FSL #define CONFIG_PMIC_FSL_MC13892 #define CONFIG_SYS_DIALOG_PMIC_I2C_ADDR 0x48 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8 diff --git a/include/configs/mx6qarm2.h b/include/configs/mx6qarm2.h index 6ebdaa8768..138e460180 100644 --- a/include/configs/mx6qarm2.h +++ b/include/configs/mx6qarm2.h @@ -51,7 +51,7 @@ #define CONFIG_MMC #define CONFIG_CMD_MMC #define CONFIG_GENERIC_MMC -#define CONFIG_MMC_BOUNCE_BUFFER +#define CONFIG_BOUNCE_BUFFER #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION diff --git a/include/configs/mx6qsabre_common.h b/include/configs/mx6qsabre_common.h index b8621b8e1c..0f226f790e 100644 --- a/include/configs/mx6qsabre_common.h +++ b/include/configs/mx6qsabre_common.h @@ -46,7 +46,7 @@ #define CONFIG_MMC #define CONFIG_CMD_MMC #define CONFIG_GENERIC_MMC -#define CONFIG_MMC_BOUNCE_BUFFER +#define CONFIG_BOUNCE_BUFFER #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h index 759275a03a..4ce4d4c086 100644 --- a/include/configs/mx6qsabrelite.h +++ b/include/configs/mx6qsabrelite.h @@ -73,7 +73,7 @@ #define CONFIG_MMC #define CONFIG_CMD_MMC #define CONFIG_GENERIC_MMC -#define CONFIG_MMC_BOUNCE_BUFFER +#define CONFIG_BOUNCE_BUFFER #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT #define CONFIG_DOS_PARTITION diff --git a/include/configs/nios2-generic.h b/include/configs/nios2-generic.h index 69ff3efb50..624bd5c7ee 100644 --- a/include/configs/nios2-generic.h +++ b/include/configs/nios2-generic.h @@ -68,6 +68,7 @@ #define CONFIG_SYS_ALTERA_PIO_GPIO_NUM LED_PIO_WIDTH #define CONFIG_STATUS_LED /* Enable status driver */ +#define CONFIG_BOARD_SPECIFIC_LED #define CONFIG_GPIO_LED /* Enable GPIO LED driver */ #define CONFIG_GPIO /* Enable GPIO driver */ diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index 7a3cc16a09..12d65f2c4e 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -117,21 +117,19 @@ #define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}} /* USB */ -#define CONFIG_MUSB_UDC 1 -#define CONFIG_USB_OMAP3 1 +#define CONFIG_MUSB_GADGET +#define CONFIG_USB_MUSB_OMAP2PLUS +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_USB_GADGET_DUALSPEED #define CONFIG_TWL4030_USB 1 - -/* USB device configuration */ -#define CONFIG_USB_DEVICE 1 -#define CONFIG_USB_TTY 1 -#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +#define CONFIG_USB_ETHER +#define CONFIG_USB_ETHER_RNDIS /* USB EHCI */ #define CONFIG_CMD_USB #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_OMAP -/*#define CONFIG_EHCI_DCACHE*/ /* leave it disabled for now */ #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147 #define CONFIG_USB_ULPI @@ -414,6 +412,9 @@ #define CONFIG_SPL_FAT_SUPPORT #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_GPIO_SUPPORT #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_SPL_OMAP3_ID_NAND diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index f6e4236998..b4d925ed90 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -113,6 +113,9 @@ /* NAND SPL */ #define CONFIG_SPL_NAND_SIMPLE #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SYS_NAND_5_ADDR_CYCLE #define CONFIG_SYS_NAND_PAGE_COUNT 64 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 diff --git a/include/configs/omap3_evm_quick_nand.h b/include/configs/omap3_evm_quick_nand.h index 362fa1d720..8f0258491e 100644 --- a/include/configs/omap3_evm_quick_nand.h +++ b/include/configs/omap3_evm_quick_nand.h @@ -81,6 +81,9 @@ */ #define CONFIG_SPL_NAND_SIMPLE #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SYS_NAND_5_ADDR_CYCLE #define CONFIG_SYS_NAND_PAGE_COUNT 64 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h index 626cf7afd5..fd31c73964 100644 --- a/include/configs/omap3_overo.h +++ b/include/configs/omap3_overo.h @@ -319,6 +319,9 @@ #define CONFIG_SPL_FAT_SUPPORT #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_GPIO_SUPPORT #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h index 350150b115..964bfcd440 100644 --- a/include/configs/p1_p2_rdb_pc.h +++ b/include/configs/p1_p2_rdb_pc.h @@ -38,6 +38,7 @@ #define __SW_BOOT_MASK 0x03 #define __SW_BOOT_NOR 0xe4 #define __SW_BOOT_SD 0x54 +#define CONFIG_SYS_L2_SIZE (256 << 10) #endif #if defined(CONFIG_P1020UTM) @@ -46,6 +47,7 @@ #define __SW_BOOT_MASK 0x03 #define __SW_BOOT_NOR 0xe0 #define __SW_BOOT_SD 0x50 +#define CONFIG_SYS_L2_SIZE (256 << 10) #endif #if defined(CONFIG_P1020RDB) @@ -61,6 +63,7 @@ #define __SW_BOOT_SD 0x9c #define __SW_BOOT_NAND 0xec #define __SW_BOOT_PCIE 0x6c +#define CONFIG_SYS_L2_SIZE (256 << 10) #endif #if defined(CONFIG_P1021RDB) @@ -78,6 +81,7 @@ #define __SW_BOOT_SD 0x9c #define __SW_BOOT_NAND 0xec #define __SW_BOOT_PCIE 0x6c +#define CONFIG_SYS_L2_SIZE (256 << 10) #endif #if defined(CONFIG_P1024RDB) @@ -91,6 +95,7 @@ #define __SW_BOOT_SPI 0x08 #define __SW_BOOT_SD 0x04 #define __SW_BOOT_NAND 0x0c +#define CONFIG_SYS_L2_SIZE (256 << 10) #endif #if defined(CONFIG_P1025RDB) @@ -108,6 +113,7 @@ #define __SW_BOOT_SPI 0x08 #define __SW_BOOT_SD 0x04 #define __SW_BOOT_NAND 0x0c +#define CONFIG_SYS_L2_SIZE (256 << 10) #endif #if defined(CONFIG_P2020RDB) @@ -122,6 +128,14 @@ #define __SW_BOOT_SD 0x68 /* or 0x18 */ #define __SW_BOOT_NAND 0xe8 #define __SW_BOOT_PCIE 0xa8 +#define CONFIG_SYS_L2_SIZE (512 << 10) +#endif + +#if CONFIG_SYS_L2_SIZE >= (512 << 10) +/* must be 32-bit */ +#define CONFIG_SYS_INIT_L2_ADDR 0xf8f80000 +#define CONFIG_SYS_INIT_L2_ADDR_PHYS CONFIG_SYS_INIT_L2_ADDR +#define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE) #endif #ifdef CONFIG_SDCARD @@ -140,16 +154,39 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc #endif -#if defined(CONFIG_NAND) && defined(CONFIG_NAND_FSL_ELBC) -#define CONFIG_NAND_U_BOOT -#define CONFIG_SYS_EXTRA_ENV_RELOC -#define CONFIG_SYS_RAMBOOT -#define CONFIG_SYS_TEXT_BASE_SPL 0xff800000 -#ifdef CONFIG_NAND_SPL -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL +#ifdef CONFIG_NAND +#define CONFIG_SPL +#define CONFIG_SPL_INIT_MINIMAL +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" + +#define CONFIG_SPL_TEXT_BASE 0xfffff000 +#define CONFIG_SPL_MAX_SIZE (4 * 1024) + +#ifdef CONFIG_SYS_INIT_L2_ADDR +/* We multiply CONFIG_SPL_MAX_SIZE by two to leave some room for BSS. */ +#define CONFIG_SYS_TEXT_BASE 0xf8f82000 +#define CONFIG_SPL_RELOC_TEXT_BASE \ + (CONFIG_SYS_INIT_L2_END - CONFIG_SPL_MAX_SIZE * 2) +#define CONFIG_SPL_RELOC_STACK \ + (CONFIG_SYS_INIT_L2_END - CONFIG_SPL_MAX_SIZE * 2) +#define CONFIG_SYS_NAND_U_BOOT_DST (CONFIG_SYS_INIT_L2_ADDR) +#define CONFIG_SYS_NAND_U_BOOT_START \ + (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SPL_MAX_SIZE) #else -#define CONFIG_SYS_TEXT_BASE 0x11001000 -#endif /* CONFIG_NAND_SPL */ +#define CONFIG_SYS_TEXT_BASE 0x00201000 +#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000 +#define CONFIG_SPL_RELOC_STACK 0x00100000 +#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE) +#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 +#endif + +#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0 +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" #endif #ifndef CONFIG_SYS_TEXT_BASE @@ -161,8 +198,12 @@ #endif #ifndef CONFIG_SYS_MONITOR_BASE +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE +#else #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ #endif +#endif /* High Level Configuration Options */ #define CONFIG_BOOKE @@ -221,7 +262,7 @@ /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k SPL code*/ -#if defined(CONFIG_NAND_SPL) +#ifdef CONFIG_SPL_BUILD #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE #endif @@ -248,39 +289,7 @@ #define CONFIG_DIMM_SLOTS_PER_CTLR 1 /* Default settings for DDR3 */ -#ifdef CONFIG_P2020RDB -#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f -#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 -#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 -#define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 -#define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000 -#define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 - -#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef -#define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 -#define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 -#define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 - -#define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 -#define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8645F607 -#define CONFIG_SYS_DDR_SR_CNTR 0x00000000 -#define CONFIG_SYS_DDR_RCW_1 0x00000000 -#define CONFIG_SYS_DDR_RCW_2 0x00000000 -#define CONFIG_SYS_DDR_CONTROL 0xC7000000 /* Type = DDR3 */ -#define CONFIG_SYS_DDR_CONTROL_2 0x24401000 -#define CONFIG_SYS_DDR_TIMING_4 0x00220001 -#define CONFIG_SYS_DDR_TIMING_5 0x02401400 - -#define CONFIG_SYS_DDR_TIMING_3 0x00020000 -#define CONFIG_SYS_DDR_TIMING_0 0x00330104 -#define CONFIG_SYS_DDR_TIMING_1 0x6f6B4644 -#define CONFIG_SYS_DDR_TIMING_2 0x0FA88CCF -#define CONFIG_SYS_DDR_CLK_CTRL 0x02000000 -#define CONFIG_SYS_DDR_MODE_1 0x00421422 -#define CONFIG_SYS_DDR_MODE_2 0x04000000 -#define CONFIG_SYS_DDR_INTERVAL 0x0C300100 - -#else +#ifndef CONFIG_P2020RDB #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 @@ -318,21 +327,18 @@ /* * Memory map * - * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable + * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable * 0x8000_0000 0xdfff_ffff PCI Express Mem 1.5G non-cacheable(PCIe * 3) + * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 + * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 512K cacheable + * (early boot only) + * 0xff80_0000 0xff80_7fff NAND flash 32K non-cacheable CS1/0 + * 0xff98_0000 0xff98_ffff PMC 64K non-cacheable CS2 + * 0xffa0_0000 0xffaf_ffff CPLD 1M non-cacheable CS3 + * 0xffb0_0000 0xffbf_ffff VSC7385 switch 1M non-cacheable CS2 * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable - * - * Localbus cacheable (TBD) - * 0xXXXX_XXXX 0xXXXX_XXXX SRAM YZ M Cacheable - * - * Localbus non-cacheable - * 0xec00_0000 0xefff_ffff FLASH Up to 64M non-cacheable - * 0xff80_0000 0xff8f_ffff NAND flash 1M non-cacheable - * 0xff90_0000 0xff97_ffff L2 SDRAM(REV.) 512K cacheable(optional) - * 0xffa0_0000 0xffaf_ffff CPLD 1M non-cacheable - * 0xffb0_0000 0xffbf_ffff VSC7385 switch 1M non-cacheable - * 0xffd0_0000 0xffd0_3fff L1 for stack 16K Cacheable TLB0 - * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable + * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable + * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable */ @@ -392,15 +398,6 @@ #define CONFIG_CMD_NAND #define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024) -/* NAND boot: 4K NAND loader config */ -#define CONFIG_SYS_NAND_SPL_SIZE 0x1000 -#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) + CONFIG_SYS_NAND_SPL_SIZE) -#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000 - CONFIG_SYS_NAND_SPL_SIZE) -#define CONFIG_SYS_NAND_U_BOOT_START 0x11000000 -#define CONFIG_SYS_NAND_U_BOOT_OFFS (0) -#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000 -#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000) - #define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ | BR_PS_8 /* Port Size = 8 bit */ \ @@ -461,7 +458,7 @@ OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \ OR_GPCM_EAD) -#ifdef CONFIG_NAND_U_BOOT +#ifdef CONFIG_NAND #define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ #define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ #define CONFIG_SYS_BR1_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ @@ -511,7 +508,7 @@ #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#ifdef CONFIG_NAND_SPL +#ifdef CONFIG_SPL_BUILD #define CONFIG_NS16550_MIN_FUNCTIONS #endif @@ -709,7 +706,6 @@ /* * Environment */ -#ifdef CONFIG_SYS_RAMBOOT #ifdef CONFIG_RAMBOOT_SPIFLASH #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_SPI_BUS 0 @@ -724,16 +720,15 @@ #define CONFIG_FSL_FIXED_MMC_LOCATION #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_SYS_MMC_ENV_DEV 0 -#elif defined(CONFIG_NAND_U_BOOT) +#elif defined(CONFIG_NAND) #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE #define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) #define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) -#else +#elif defined(CONFIG_SYS_RAMBOOT) #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 -#endif #else #define CONFIG_ENV_IS_IN_FLASH #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 diff --git a/include/configs/qong.h b/include/configs/qong.h index e43a02110e..d9bf2010b8 100644 --- a/include/configs/qong.h +++ b/include/configs/qong.h @@ -58,9 +58,9 @@ #define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH) #define CONFIG_RTC_MC13XXX -#define CONFIG_PMIC -#define CONFIG_PMIC_SPI -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_SPI +#define CONFIG_POWER_FSL #define CONFIG_FSL_PMIC_BUS 1 #define CONFIG_FSL_PMIC_CS 0 #define CONFIG_FSL_PMIC_CLK 100000 diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h index 7e0b302935..56e83478f8 100644 --- a/include/configs/s5p_goni.h +++ b/include/configs/s5p_goni.h @@ -215,9 +215,9 @@ #define CONFIG_SYS_CACHELINE_SIZE 64 -#define CONFIG_PMIC -#define CONFIG_PMIC_I2C -#define CONFIG_PMIC_MAX8998 +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_MAX8998 #include <asm/arch/gpio.h> /* diff --git a/include/configs/s5pc210_universal.h b/include/configs/s5pc210_universal.h index 5fc6136435..894f38bd7d 100644 --- a/include/configs/s5pc210_universal.h +++ b/include/configs/s5pc210_universal.h @@ -253,9 +253,9 @@ #define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_MAX_I2C_BUS 7 -#define CONFIG_PMIC -#define CONFIG_PMIC_I2C -#define CONFIG_PMIC_MAX8998 +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_MAX8998 #define CONFIG_USB_GADGET #define CONFIG_USB_GADGET_S3C_UDC_OTG diff --git a/include/configs/sc_sps_1.h b/include/configs/sc_sps_1.h index f5dc393020..cb99d58644 100644 --- a/include/configs/sc_sps_1.h +++ b/include/configs/sc_sps_1.h @@ -140,7 +140,7 @@ #ifdef CONFIG_CMD_MMC #define CONFIG_APBH_DMA #define CONFIG_MMC -#define CONFIG_MMC_BOUNCE_BUFFER +#define CONFIG_BOUNCE_BUFFER #define CONFIG_GENERIC_MMC #define CONFIG_MXS_MMC #endif diff --git a/include/configs/seaboard.h b/include/configs/seaboard.h index 74d3b94887..ab10bd0abc 100644 --- a/include/configs/seaboard.h +++ b/include/configs/seaboard.h @@ -99,10 +99,8 @@ #define CONFIG_TEGRA_KEYBOARD #define CONFIG_KEYBOARD -#undef TEGRA_DEVICE_SETTINGS -#define TEGRA_DEVICE_SETTINGS "stdin=serial,tegra-kbc\0" \ - "stdout=serial\0" \ - "stderr=serial\0" +/* USB keyboard */ +#define CONFIG_USB_KEYBOARD #include "tegra-common-post.h" diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 8e6954e3aa..dd5d7cd260 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -288,9 +288,6 @@ #define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_EHCI_MMIO_BIG_ENDIAN #define CONFIG_EHCI_DESC_BIG_ENDIAN -#ifdef CONFIG_4xx_DCACHE -#define CONFIG_EHCI_DCACHE -#endif #else /* CONFIG_USB_EHCI */ #define CONFIG_USB_OHCI_NEW #define CONFIG_SYS_OHCI_BE_CONTROLLER diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h index dd7757cb97..ee73c277b9 100644 --- a/include/configs/tam3517-common.h +++ b/include/configs/tam3517-common.h @@ -106,8 +106,6 @@ #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #define CONFIG_USB_STORAGE -/* #define CONFIG_EHCI_DCACHE */ - /* commands to include */ #include <config_cmd_default.h> @@ -254,6 +252,9 @@ #define CONFIG_SPL_GPIO_SUPPORT #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" #define CONFIG_SPL_TEXT_BASE 0x40200000 /*CONFIG_SYS_SRAM_START*/ diff --git a/include/configs/tegra-common-post.h b/include/configs/tegra-common-post.h index 6835155d11..6f310bee60 100644 --- a/include/configs/tegra-common-post.h +++ b/include/configs/tegra-common-post.h @@ -165,6 +165,25 @@ "fdt_addr_r=0x02000000\0" \ "ramdisk_addr_r=0x02100000\0" \ +#ifdef CONFIG_TEGRA_KEYBOARD +#define STDIN_KBD_KBC ",tegra-kbc" +#else +#define STDIN_KBD_KBC "" +#endif + +#ifdef CONFIG_USB_KEYBOARD +#define STDIN_KBD_USB ",usbkbd" +#define CONFIG_SYS_USB_EVENT_POLL +#define CONFIG_PREBOOT "usb start" +#else +#define STDIN_KBD_USB "" +#endif + +#define TEGRA_DEVICE_SETTINGS \ + "stdin=serial" STDIN_KBD_KBC STDIN_KBD_USB "\0" \ + "stdout=serial\0" \ + "stderr=serial\0" \ + #define CONFIG_EXTRA_ENV_SETTINGS \ TEGRA_DEVICE_SETTINGS \ MEM_LAYOUT_ENV_SETTINGS \ diff --git a/include/configs/tegra20-common.h b/include/configs/tegra20-common.h index 15bd9bb146..5c0833a4d8 100644 --- a/include/configs/tegra20-common.h +++ b/include/configs/tegra20-common.h @@ -100,7 +100,6 @@ */ #define CONFIG_USB_EHCI_TXFIFO_THRESH 10 #define CONFIG_EHCI_IS_TDI -#define CONFIG_EHCI_DCACHE /* Total I2C ports on Tegra20 */ #define TEGRA_I2C_NUM_CONTROLLERS 4 @@ -125,12 +124,8 @@ #define CONFIG_SYS_NO_FLASH -/* Environment information, boards can override if required */ #define CONFIG_CONSOLE_MUX #define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define TEGRA_DEVICE_SETTINGS "stdin=serial\0" \ - "stdout=serial\0" \ - "stderr=serial\0" #define CONFIG_LOADADDR 0x408000 /* def. location for kernel */ #define CONFIG_BOOTDELAY 2 /* -1 to disable auto boot */ @@ -207,4 +202,7 @@ #define CONFIG_SYS_NAND_SELF_INIT #define CONFIG_SYS_NAND_ONFI_DETECTION +/* Misc utility code */ +#define CONFIG_BOUNCE_BUFFER + #endif /* __TEGRA20_COMMON_H */ diff --git a/include/configs/trats.h b/include/configs/trats.h index d7808aa712..355029e8d8 100644 --- a/include/configs/trats.h +++ b/include/configs/trats.h @@ -234,10 +234,16 @@ #define CONFIG_SOFT_I2C_GPIO_SDA get_multi_sda_pin() #define I2C_INIT multi_i2c_init() -#define CONFIG_PMIC -#define CONFIG_PMIC_I2C -#define CONFIG_PMIC_MAX8997 - +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_MAX8997 + +#define CONFIG_POWER_FG +#define CONFIG_POWER_FG_MAX17042 +#define CONFIG_POWER_MUIC +#define CONFIG_POWER_MUIC_MAX8997 +#define CONFIG_POWER_BATTERY +#define CONFIG_POWER_BATTERY_TRATS #define CONFIG_USB_GADGET #define CONFIG_USB_GADGET_S3C_UDC_OTG #define CONFIG_USB_GADGET_DUALSPEED diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h index 5859a7337b..be0d2ec3c7 100644 --- a/include/configs/tricorder.h +++ b/include/configs/tricorder.h @@ -282,6 +282,9 @@ #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_MMC_SUPPORT #define CONFIG_SPL_FAT_SUPPORT #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" diff --git a/include/configs/tt01.h b/include/configs/tt01.h index f46efa55f1..9f8f240f82 100644 --- a/include/configs/tt01.h +++ b/include/configs/tt01.h @@ -149,9 +149,9 @@ #define CONFIG_MXC_GPIO /* MC13783 connected to CSPI3 and SS0 */ -#define CONFIG_PMIC -#define CONFIG_PMIC_SPI -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_SPI +#define CONFIG_POWER_FSL #define CONFIG_FSL_PMIC_BUS 2 #define CONFIG_FSL_PMIC_CS 0 diff --git a/include/configs/vct.h b/include/configs/vct.h index b4b0949522..7aeb66801e 100644 --- a/include/configs/vct.h +++ b/include/configs/vct.h @@ -136,7 +136,6 @@ */ #define CONFIG_USB_EHCI /* Enable EHCI USB support */ #define CONFIG_USB_EHCI_VCT /* on VCT platform */ -#define CONFIG_EHCI_DCACHE /* with dcache handling support */ #define CONFIG_EHCI_MMIO_BIG_ENDIAN #define CONFIG_EHCI_DESC_BIG_ENDIAN #define CONFIG_EHCI_IS_TDI diff --git a/include/configs/ventana.h b/include/configs/ventana.h index b751d58bc8..4c9b31cce3 100644 --- a/include/configs/ventana.h +++ b/include/configs/ventana.h @@ -75,6 +75,9 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_DHCP +/* USB keyboard */ +#define CONFIG_USB_KEYBOARD + #include "tegra-common-post.h" #endif /* __CONFIG_H */ diff --git a/include/configs/vision2.h b/include/configs/vision2.h index 13c570299f..226d04901f 100644 --- a/include/configs/vision2.h +++ b/include/configs/vision2.h @@ -87,9 +87,9 @@ #define CONFIG_ENV_IS_IN_SPI_FLASH /* PMIC Controller */ -#define CONFIG_PMIC -#define CONFIG_PMIC_SPI -#define CONFIG_PMIC_FSL +#define CONFIG_POWER +#define CONFIG_POWER_SPI +#define CONFIG_POWER_FSL #define CONFIG_FSL_PMIC_BUS 0 #define CONFIG_FSL_PMIC_CS 0 #define CONFIG_FSL_PMIC_CLK 2500000 diff --git a/include/configs/woodburn_common.h b/include/configs/woodburn_common.h index 58a96cffce..a1452b96cf 100644 --- a/include/configs/woodburn_common.h +++ b/include/configs/woodburn_common.h @@ -66,10 +66,10 @@ #define CONFIG_MXC_GPIO /* PMIC Controller */ -#define CONFIG_PMIC -#define CONFIG_PMIC_I2C +#define CONFIG_POWER +#define CONFIG_POWER_I2C +#define CONFIG_POWER_FSL #define CONFIG_PMIC_FSL_MC13892 -#define CONFIG_PMIC_FSL #define CONFIG_SYS_FSL_PMIC_I2C_ADDR 0x8 #define CONFIG_RTC_MC13XXX diff --git a/include/fdtdec.h b/include/fdtdec.h index 0b140752ff..5164ce24e6 100644 --- a/include/fdtdec.h +++ b/include/fdtdec.h @@ -40,10 +40,12 @@ typedef u64 fdt_addr_t; #define FDT_ADDR_T_NONE (-1ULL) #define fdt_addr_to_cpu(reg) be64_to_cpu(reg) +#define fdt_size_to_cpu(reg) be64_to_cpu(reg) #else typedef u32 fdt_addr_t; #define FDT_ADDR_T_NONE (-1U) #define fdt_addr_to_cpu(reg) be32_to_cpu(reg) +#define fdt_size_to_cpu(reg) be32_to_cpu(reg) #endif /* Information obtained about memory from the FDT */ @@ -88,6 +90,22 @@ struct fdt_gpio_state { #define fdt_gpio_isvalid(x) ((x)->gpio != FDT_GPIO_NONE) /** + * Read the GPIO taking into account the polarity of the pin. + * + * @param gpio pointer to the decoded gpio + * @return value of the gpio if successful, < 0 if unsuccessful + */ +int fdtdec_get_gpio(struct fdt_gpio_state *gpio); + +/** + * Write the GPIO taking into account the polarity of the pin. + * + * @param gpio pointer to the decoded gpio + * @return 0 if successful + */ +int fdtdec_set_gpio(struct fdt_gpio_state *gpio, int val); + +/** * Find the next numbered alias for a peripheral. This is used to enumerate * all the peripherals of a certain type. * @@ -108,6 +126,19 @@ int fdtdec_next_alias(const void *blob, const char *name, enum fdt_compat_id id, int *upto); /** + * Find the compatible ID for a given node. + * + * Generally each node has at least one compatible string attached to it. + * This function looks through our list of known compatible strings and + * returns the corresponding ID which matches the compatible string. + * + * @param blob FDT blob to use + * @param node Node containing compatible string to find + * @return compatible ID, or COMPAT_UNKNOWN if we cannot find a match + */ +enum fdt_compat_id fdtdec_lookup(const void *blob, int node); + +/** * Find the next compatible node for a peripheral. * * Do the first call with node = 0. This function will return a pointer to @@ -167,6 +198,21 @@ s32 fdtdec_get_int(const void *blob, int node, const char *prop_name, s32 default_val); /** + * Look up a 64-bit integer property in a node and return it. The property + * must have at least 8 bytes of data (2 cells). The first two cells are + * concatenated to form a 8 bytes value, where the first cell is top half and + * the second cell is bottom half. + * + * @param blob FDT blob + * @param node node to examine + * @param prop_name name of property to find + * @param default_val default value to return if the property is not found + * @return integer value, if found, or default_val if not + */ +uint64_t fdtdec_get_uint64(const void *blob, int node, const char *prop_name, + uint64_t default_val); + +/** * Checks whether a node is enabled. * This looks for a 'status' property. If this exists, then returns 1 if * the status is 'ok' and 0 otherwise. If there is no status property, @@ -343,6 +389,22 @@ int fdtdec_decode_gpio(const void *blob, int node, const char *prop_name, struct fdt_gpio_state *gpio); /** + * Decode a list of GPIOs from an FDT. This creates a list of GPIOs with no + * terminating item. + * + * @param blob FDT blob to use + * @param node Node to look at + * @param prop_name Node property name + * @param gpio Array of gpio elements to fill from FDT. This will be + * untouched if either 0 or an error is returned + * @param max_count Maximum number of elements allowed + * @return number of GPIOs read if ok, -FDT_ERR_BADLAYOUT if max_count would + * be exceeded, or -FDT_ERR_NOTFOUND if the property is missing. + */ +int fdtdec_decode_gpios(const void *blob, int node, const char *prop_name, + struct fdt_gpio_state *gpio, int max_count); + +/** * Set up a GPIO pin according to the provided gpio information. At present this * just requests the GPIO. * @@ -354,6 +416,39 @@ int fdtdec_decode_gpio(const void *blob, int node, const char *prop_name, */ int fdtdec_setup_gpio(struct fdt_gpio_state *gpio); +/** + * Look in the FDT for a config item with the given name and return its value + * as a 32-bit integer. The property must have at least 4 bytes of data. The + * value of the first cell is returned. + * + * @param blob FDT blob to use + * @param prop_name Node property name + * @param default_val default value to return if the property is not found + * @return integer value, if found, or default_val if not + */ +int fdtdec_get_config_int(const void *blob, const char *prop_name, + int default_val); + +/** + * Look in the FDT for a config item with the given name + * and return whether it exists. + * + * @param blob FDT blob + * @param prop_name property name to look up + * @return 1, if it exists, or 0 if not + */ +int fdtdec_get_config_bool(const void *blob, const char *prop_name); + +/** + * Look in the FDT for a config item with the given name and return its value + * as a string. + * + * @param blob FDT blob + * @param prop_name property name to look up + * @returns property string, NULL on error. + */ +char *fdtdec_get_config_string(const void *blob, const char *prop_name); + /* * Look up a property in a node and return its contents in a byte * array of given length. The property must have at least enough data for @@ -385,4 +480,21 @@ int fdtdec_get_byte_array(const void *blob, int node, const char *prop_name, */ const u8 *fdtdec_locate_byte_array(const void *blob, int node, const char *prop_name, int count); + +/** + * Look up a property in a node which contains a memory region address and + * size. Then return a pointer to this address. + * + * The property must hold one address with a length. This is only tested on + * 32-bit machines. + * + * @param blob FDT blob + * @param node node to examine + * @param prop_name name of property to find + * @param ptrp returns pointer to region, or NULL if no address + * @param size returns size of region + * @return 0 if ok, -1 on error (propery not found) + */ +int fdtdec_decode_region(const void *blob, int node, + const char *prop_name, void **ptrp, size_t *size); #endif diff --git a/include/g_dnl.h b/include/g_dnl.h index 0ec7440306..f47395f35d 100644 --- a/include/g_dnl.h +++ b/include/g_dnl.h @@ -22,7 +22,6 @@ #define __G_DOWNLOAD_H_ #include <linux/usb/ch9.h> -#include <usbdescriptors.h> #include <linux/usb/gadget.h> int g_dnl_register(const char *s); diff --git a/include/image.h b/include/image.h index 0a895f2044..f54d983306 100644 --- a/include/image.h +++ b/include/image.h @@ -615,6 +615,7 @@ int fit_image_check_type(const void *fit, int noffset, uint8_t type); int fit_image_check_comp(const void *fit, int noffset, uint8_t comp); int fit_check_format(const void *fit); +int fit_conf_find_compat(const void *fit, const void *fdt); int fit_conf_get_node(const void *fit, const char *conf_uname); int fit_conf_get_kernel_node(const void *fit, int noffset); int fit_conf_get_ramdisk_node(const void *fit, int noffset); diff --git a/include/lcd.h b/include/lcd.h index 42070d7636..2517d39d41 100644 --- a/include/lcd.h +++ b/include/lcd.h @@ -294,6 +294,42 @@ void lcd_printf (const char *fmt, ...); void lcd_clear(void); int lcd_display_bitmap(ulong bmp_image, int x, int y); +/** + * Get the width of the LCD in pixels + * + * @return width of LCD in pixels + */ +int lcd_get_pixel_width(void); + +/** + * Get the height of the LCD in pixels + * + * @return height of LCD in pixels + */ +int lcd_get_pixel_height(void); + +/** + * Get the number of text lines/rows on the LCD + * + * @return number of rows + */ +int lcd_get_screen_rows(void); + +/** + * Get the number of text columns on the LCD + * + * @return number of columns + */ +int lcd_get_screen_columns(void); + +/** + * Set the position of the text cursor + * + * @param col Column to place cursor (0 = left side) + * @param row Row to place cursor (0 = top line) + */ +void lcd_position_cursor(unsigned col, unsigned row); + /* Allow boards to customize the information displayed */ void lcd_show_board_info(void); diff --git a/include/linux/byteorder/swab.h b/include/linux/byteorder/swab.h index bb4a046937..4334fa77e3 100644 --- a/include/linux/byteorder/swab.h +++ b/include/linux/byteorder/swab.h @@ -122,7 +122,6 @@ static __inline__ void __swab32s(__u32 *addr) __arch__swab32s(addr); } -#ifdef __BYTEORDER_HAS_U64__ static __inline__ __attribute__((const)) __u64 __fswab64(__u64 x) { # ifdef __SWAB_64_THRU_32__ @@ -141,7 +140,6 @@ static __inline__ void __swab64s(__u64 *addr) { __arch__swab64s(addr); } -#endif /* __BYTEORDER_HAS_U64__ */ #if defined(__KERNEL__) #define swab16 __swab16 diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h index f63e04b634..e9e904523a 100644 --- a/include/linux/mtd/nand.h +++ b/include/linux/mtd/nand.h @@ -194,6 +194,9 @@ typedef enum { /* Device behaves just like nand, but is readonly */ #define NAND_ROM 0x00000800 +/* Device supports subpage reads */ +#define NAND_SUBPAGE_READ 0x00001000 + /* Options valid for Samsung large page devices */ #define NAND_SAMSUNG_LP_OPTIONS \ (NAND_NO_PADDING | NAND_CACHEPRG | NAND_COPYBACK) @@ -203,9 +206,7 @@ typedef enum { #define NAND_MUST_PAD(chip) (!(chip->options & NAND_NO_PADDING)) #define NAND_HAS_CACHEPROG(chip) ((chip->options & NAND_CACHEPRG)) #define NAND_HAS_COPYBACK(chip) ((chip->options & NAND_COPYBACK)) -/* Large page NAND with SOFT_ECC should support subpage reads */ -#define NAND_SUBPAGE_READ(chip) ((chip->ecc.mode == NAND_ECC_SOFT) \ - && (chip->page_shift > 9)) +#define NAND_HAS_SUBPAGE_READ(chip) ((chip->options & NAND_SUBPAGE_READ)) /* Non chip related options */ /* diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h index ce1d1e10ba..d1d732c283 100644 --- a/include/linux/usb/ch9.h +++ b/include/linux/usb/ch9.h @@ -28,15 +28,13 @@ * [c] for consistency, removing all doubt even when it appears to * someone that the two other points are non-issues for that * particular descriptor type. - * - * Ported to U-boot by: Thomas Smits <ts.smits@gmail.com> and - * Remy Bohmer <linux@bohmer.net> */ #ifndef __LINUX_USB_CH9_H #define __LINUX_USB_CH9_H #include <linux/types.h> /* __u8 etc */ +#include <asm/byteorder.h> /* le16_to_cpu */ /*-------------------------------------------------------------------------*/ @@ -70,7 +68,7 @@ #define USB_RECIP_OTHER 0x03 /* From Wireless USB 1.0 */ #define USB_RECIP_PORT 0x04 -#define USB_RECIP_RPIPE 0x05 +#define USB_RECIP_RPIPE 0x05 /* * Standard requests, for the bRequest field of a SETUP packet. @@ -90,6 +88,8 @@ #define USB_REQ_GET_INTERFACE 0x0A #define USB_REQ_SET_INTERFACE 0x0B #define USB_REQ_SYNCH_FRAME 0x0C +#define USB_REQ_SET_SEL 0x30 +#define USB_REQ_SET_ISOCH_DELAY 0x31 #define USB_REQ_SET_ENCRYPTION 0x0D /* Wireless USB */ #define USB_REQ_GET_ENCRYPTION 0x0E @@ -105,10 +105,16 @@ #define USB_REQ_LOOPBACK_DATA_READ 0x16 #define USB_REQ_SET_INTERFACE_DS 0x17 +/* The Link Power Management (LPM) ECN defines USB_REQ_TEST_AND_SET command, + * used by hubs to put ports into a new L1 suspend state, except that it + * forgot to define its number ... + */ + /* * USB feature flags are written using USB_REQ_{CLEAR,SET}_FEATURE, and * are read as a bit array returned by USB_REQ_GET_STATUS. (So there - * are at most sixteen features of each type.) + * are at most sixteen features of each type.) Hubs may also support a + * new USB_REQ_TEST_AND_SET_FEATURE to put ports into L1 suspend. */ #define USB_DEVICE_SELF_POWERED 0 /* (read only) */ #define USB_DEVICE_REMOTE_WAKEUP 1 /* dev may initiate wakeup */ @@ -120,8 +126,38 @@ #define USB_DEVICE_A_ALT_HNP_SUPPORT 5 /* (otg) other RH port does */ #define USB_DEVICE_DEBUG_MODE 6 /* (special devices only) */ +/* + * Test Mode Selectors + * See USB 2.0 spec Table 9-7 + */ +#define TEST_J 1 +#define TEST_K 2 +#define TEST_SE0_NAK 3 +#define TEST_PACKET 4 +#define TEST_FORCE_EN 5 + +/* + * New Feature Selectors as added by USB 3.0 + * See USB 3.0 spec Table 9-6 + */ +#define USB_DEVICE_U1_ENABLE 48 /* dev may initiate U1 transition */ +#define USB_DEVICE_U2_ENABLE 49 /* dev may initiate U2 transition */ +#define USB_DEVICE_LTM_ENABLE 50 /* dev may send LTM */ +#define USB_INTRF_FUNC_SUSPEND 0 /* function suspend */ + +#define USB_INTR_FUNC_SUSPEND_OPT_MASK 0xFF00 +/* + * Suspend Options, Table 9-7 USB 3.0 spec + */ +#define USB_INTRF_FUNC_SUSPEND_LP (1 << (8 + 0)) +#define USB_INTRF_FUNC_SUSPEND_RW (1 << (8 + 1)) + #define USB_ENDPOINT_HALT 0 /* IN/OUT will STALL */ +/* Bit array elements as returned by the USB_REQ_GET_STATUS request. */ +#define USB_DEV_STAT_U1_ENABLED 2 /* transition into U1 state */ +#define USB_DEV_STAT_U2_ENABLED 3 /* transition into U2 state */ +#define USB_DEV_STAT_LTM_ENABLED 4 /* Latency tolerance messages */ /** * struct usb_ctrlrequest - SETUP data for a USB device control request @@ -140,10 +176,6 @@ * For most devices, interfaces don't coordinate with each other, so * such requests may be made at any time. */ -#if defined(__BIG_ENDIAN) || defined(__ARMEB__) -#error (functionality not verified for big endian targets, todo...) -#endif - struct usb_ctrlrequest { __u8 bRequestType; __u8 bRequest; @@ -159,8 +191,12 @@ struct usb_ctrlrequest { * (rarely) accepted by SET_DESCRIPTOR. * * Note that all multi-byte values here are encoded in little endian - * byte order "on the wire". But when exposed through Linux-USB APIs, - * they've been converted to cpu byte order. + * byte order "on the wire". Within the kernel and when exposed + * through the Linux-USB APIs, they are not converted to cpu byte + * order; it is the responsibility of the client code to do this. + * The single exception is when device and configuration descriptors (but + * not other descriptors) are read from usbfs (i.e. /proc/bus/usb/BBB/DDD); + * in this case the fields are converted to host endianness by the kernel. */ /* @@ -187,6 +223,11 @@ struct usb_ctrlrequest { #define USB_DT_WIRELESS_ENDPOINT_COMP 0x11 #define USB_DT_WIRE_ADAPTER 0x21 #define USB_DT_RPIPE 0x22 +#define USB_DT_CS_RADIO_CONTROL 0x23 +/* From the T10 UAS specification */ +#define USB_DT_PIPE_USAGE 0x24 +/* From the USB 3.0 spec */ +#define USB_DT_SS_ENDPOINT_COMP 0x30 /* Conventional codes for class-specific descriptors. The convention is * defined in the USB "Common Class" Spec (3.11). Individual class specs @@ -204,6 +245,28 @@ struct usb_descriptor_header { __u8 bDescriptorType; } __attribute__ ((packed)); + +/*-------------------------------------------------------------------------*/ + +/* USB_DT_DEVICE: Device descriptor */ +struct usb_device_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __le16 bcdUSB; + __u8 bDeviceClass; + __u8 bDeviceSubClass; + __u8 bDeviceProtocol; + __u8 bMaxPacketSize0; + __le16 idVendor; + __le16 idProduct; + __le16 bcdDevice; + __u8 iManufacturer; + __u8 iProduct; + __u8 iSerialNumber; + __u8 bNumConfigurations; +} __attribute__ ((packed)); + #define USB_DT_DEVICE_SIZE 18 @@ -230,6 +293,8 @@ struct usb_descriptor_header { #define USB_CLASS_APP_SPEC 0xfe #define USB_CLASS_VENDOR_SPEC 0xff +#define USB_SUBCLASS_VENDOR_SPEC 0xff + /*-------------------------------------------------------------------------*/ /* USB_DT_CONFIG: Configuration descriptor information. @@ -260,11 +325,56 @@ struct usb_config_descriptor { #define USB_CONFIG_ATT_WAKEUP (1 << 5) /* can wakeup */ #define USB_CONFIG_ATT_BATTERY (1 << 4) /* battery powered */ +/*-------------------------------------------------------------------------*/ + +/* USB_DT_STRING: String descriptor */ +struct usb_string_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __le16 wData[1]; /* UTF-16LE encoded */ +} __attribute__ ((packed)); + /* note that "string" zero is special, it holds language codes that * the device supports, not Unicode characters. */ +/*-------------------------------------------------------------------------*/ + +/* USB_DT_INTERFACE: Interface descriptor */ +struct usb_interface_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __u8 bInterfaceNumber; + __u8 bAlternateSetting; + __u8 bNumEndpoints; + __u8 bInterfaceClass; + __u8 bInterfaceSubClass; + __u8 bInterfaceProtocol; + __u8 iInterface; +} __attribute__ ((packed)); + #define USB_DT_INTERFACE_SIZE 9 + +/*-------------------------------------------------------------------------*/ + +/* USB_DT_ENDPOINT: Endpoint descriptor */ +struct usb_endpoint_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __u8 bEndpointAddress; + __u8 bmAttributes; + __le16 wMaxPacketSize; + __u8 bInterval; + + /* NOTE: these two are _only_ in audio endpoints. */ + /* use USB_DT_ENDPOINT*_SIZE in bLength, not sizeof. */ + __u8 bRefresh; + __u8 bSynchAddress; +} __attribute__ ((packed)); + #define USB_DT_ENDPOINT_SIZE 7 #define USB_DT_ENDPOINT_AUDIO_SIZE 9 /* Audio extension */ @@ -282,6 +392,254 @@ struct usb_config_descriptor { #define USB_ENDPOINT_XFER_INT 3 #define USB_ENDPOINT_MAX_ADJUSTABLE 0x80 +/* The USB 3.0 spec redefines bits 5:4 of bmAttributes as interrupt ep type. */ +#define USB_ENDPOINT_INTRTYPE 0x30 +#define USB_ENDPOINT_INTR_PERIODIC (0 << 4) +#define USB_ENDPOINT_INTR_NOTIFICATION (1 << 4) + +#define USB_ENDPOINT_SYNCTYPE 0x0c +#define USB_ENDPOINT_SYNC_NONE (0 << 2) +#define USB_ENDPOINT_SYNC_ASYNC (1 << 2) +#define USB_ENDPOINT_SYNC_ADAPTIVE (2 << 2) +#define USB_ENDPOINT_SYNC_SYNC (3 << 2) + +#define USB_ENDPOINT_USAGE_MASK 0x30 +#define USB_ENDPOINT_USAGE_DATA 0x00 +#define USB_ENDPOINT_USAGE_FEEDBACK 0x10 +#define USB_ENDPOINT_USAGE_IMPLICIT_FB 0x20 /* Implicit feedback Data endpoint */ + +/*-------------------------------------------------------------------------*/ + +/** + * usb_endpoint_num - get the endpoint's number + * @epd: endpoint to be checked + * + * Returns @epd's number: 0 to 15. + */ +static inline int usb_endpoint_num(const struct usb_endpoint_descriptor *epd) +{ + return epd->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK; +} + +/** + * usb_endpoint_type - get the endpoint's transfer type + * @epd: endpoint to be checked + * + * Returns one of USB_ENDPOINT_XFER_{CONTROL, ISOC, BULK, INT} according + * to @epd's transfer type. + */ +static inline int usb_endpoint_type(const struct usb_endpoint_descriptor *epd) +{ + return epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK; +} + +/** + * usb_endpoint_dir_in - check if the endpoint has IN direction + * @epd: endpoint to be checked + * + * Returns true if the endpoint is of type IN, otherwise it returns false. + */ +static inline int usb_endpoint_dir_in(const struct usb_endpoint_descriptor *epd) +{ + return ((epd->bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_IN); +} + +/** + * usb_endpoint_dir_out - check if the endpoint has OUT direction + * @epd: endpoint to be checked + * + * Returns true if the endpoint is of type OUT, otherwise it returns false. + */ +static inline int usb_endpoint_dir_out( + const struct usb_endpoint_descriptor *epd) +{ + return ((epd->bEndpointAddress & USB_ENDPOINT_DIR_MASK) == USB_DIR_OUT); +} + +/** + * usb_endpoint_xfer_bulk - check if the endpoint has bulk transfer type + * @epd: endpoint to be checked + * + * Returns true if the endpoint is of type bulk, otherwise it returns false. + */ +static inline int usb_endpoint_xfer_bulk( + const struct usb_endpoint_descriptor *epd) +{ + return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == + USB_ENDPOINT_XFER_BULK); +} + +/** + * usb_endpoint_xfer_control - check if the endpoint has control transfer type + * @epd: endpoint to be checked + * + * Returns true if the endpoint is of type control, otherwise it returns false. + */ +static inline int usb_endpoint_xfer_control( + const struct usb_endpoint_descriptor *epd) +{ + return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == + USB_ENDPOINT_XFER_CONTROL); +} + +/** + * usb_endpoint_xfer_int - check if the endpoint has interrupt transfer type + * @epd: endpoint to be checked + * + * Returns true if the endpoint is of type interrupt, otherwise it returns + * false. + */ +static inline int usb_endpoint_xfer_int( + const struct usb_endpoint_descriptor *epd) +{ + return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == + USB_ENDPOINT_XFER_INT); +} + +/** + * usb_endpoint_xfer_isoc - check if the endpoint has isochronous transfer type + * @epd: endpoint to be checked + * + * Returns true if the endpoint is of type isochronous, otherwise it returns + * false. + */ +static inline int usb_endpoint_xfer_isoc( + const struct usb_endpoint_descriptor *epd) +{ + return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) == + USB_ENDPOINT_XFER_ISOC); +} + +/** + * usb_endpoint_is_bulk_in - check if the endpoint is bulk IN + * @epd: endpoint to be checked + * + * Returns true if the endpoint has bulk transfer type and IN direction, + * otherwise it returns false. + */ +static inline int usb_endpoint_is_bulk_in( + const struct usb_endpoint_descriptor *epd) +{ + return usb_endpoint_xfer_bulk(epd) && usb_endpoint_dir_in(epd); +} + +/** + * usb_endpoint_is_bulk_out - check if the endpoint is bulk OUT + * @epd: endpoint to be checked + * + * Returns true if the endpoint has bulk transfer type and OUT direction, + * otherwise it returns false. + */ +static inline int usb_endpoint_is_bulk_out( + const struct usb_endpoint_descriptor *epd) +{ + return usb_endpoint_xfer_bulk(epd) && usb_endpoint_dir_out(epd); +} + +/** + * usb_endpoint_is_int_in - check if the endpoint is interrupt IN + * @epd: endpoint to be checked + * + * Returns true if the endpoint has interrupt transfer type and IN direction, + * otherwise it returns false. + */ +static inline int usb_endpoint_is_int_in( + const struct usb_endpoint_descriptor *epd) +{ + return usb_endpoint_xfer_int(epd) && usb_endpoint_dir_in(epd); +} + +/** + * usb_endpoint_is_int_out - check if the endpoint is interrupt OUT + * @epd: endpoint to be checked + * + * Returns true if the endpoint has interrupt transfer type and OUT direction, + * otherwise it returns false. + */ +static inline int usb_endpoint_is_int_out( + const struct usb_endpoint_descriptor *epd) +{ + return usb_endpoint_xfer_int(epd) && usb_endpoint_dir_out(epd); +} + +/** + * usb_endpoint_is_isoc_in - check if the endpoint is isochronous IN + * @epd: endpoint to be checked + * + * Returns true if the endpoint has isochronous transfer type and IN direction, + * otherwise it returns false. + */ +static inline int usb_endpoint_is_isoc_in( + const struct usb_endpoint_descriptor *epd) +{ + return usb_endpoint_xfer_isoc(epd) && usb_endpoint_dir_in(epd); +} + +/** + * usb_endpoint_is_isoc_out - check if the endpoint is isochronous OUT + * @epd: endpoint to be checked + * + * Returns true if the endpoint has isochronous transfer type and OUT direction, + * otherwise it returns false. + */ +static inline int usb_endpoint_is_isoc_out( + const struct usb_endpoint_descriptor *epd) +{ + return usb_endpoint_xfer_isoc(epd) && usb_endpoint_dir_out(epd); +} + +/** + * usb_endpoint_maxp - get endpoint's max packet size + * @epd: endpoint to be checked + * + * Returns @epd's max packet + */ +static inline int usb_endpoint_maxp(const struct usb_endpoint_descriptor *epd) +{ + return __le16_to_cpu(epd->wMaxPacketSize); +} + +static inline int usb_endpoint_interrupt_type( + const struct usb_endpoint_descriptor *epd) +{ + return epd->bmAttributes & USB_ENDPOINT_INTRTYPE; +} + +/*-------------------------------------------------------------------------*/ + +/* USB_DT_SS_ENDPOINT_COMP: SuperSpeed Endpoint Companion descriptor */ +struct usb_ss_ep_comp_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __u8 bMaxBurst; + __u8 bmAttributes; + __le16 wBytesPerInterval; +} __attribute__ ((packed)); + +#define USB_DT_SS_EP_COMP_SIZE 6 + +/* Bits 4:0 of bmAttributes if this is a bulk endpoint */ +static inline int +usb_ss_max_streams(const struct usb_ss_ep_comp_descriptor *comp) +{ + int max_streams; + + if (!comp) + return 0; + + max_streams = comp->bmAttributes & 0x1f; + + if (!max_streams) + return 0; + + max_streams = 1 << max_streams; + + return max_streams; +} + +/* Bits 1:0 of bmAttributes if this is an isoc endpoint */ +#define USB_SS_MULT(p) (1 + ((p) & 0x3)) /*-------------------------------------------------------------------------*/ @@ -388,7 +746,7 @@ struct usb_encryption_descriptor { /*-------------------------------------------------------------------------*/ -/* USB_DT_BOS: group of wireless capabilities */ +/* USB_DT_BOS: group of device-level capabilities */ struct usb_bos_descriptor { __u8 bLength; __u8 bDescriptorType; @@ -397,6 +755,7 @@ struct usb_bos_descriptor { __u8 bNumDeviceCaps; } __attribute__((packed)); +#define USB_DT_BOS_SIZE 5 /*-------------------------------------------------------------------------*/ /* USB_DT_DEVICE_CAPABILITY: grouped with BOS */ @@ -434,6 +793,61 @@ struct usb_wireless_cap_descriptor { /* Ultra Wide Band */ __u8 bReserved; } __attribute__((packed)); +/* USB 2.0 Extension descriptor */ +#define USB_CAP_TYPE_EXT 2 + +struct usb_ext_cap_descriptor { /* Link Power Management */ + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; + __le32 bmAttributes; +#define USB_LPM_SUPPORT (1 << 1) /* supports LPM */ +#define USB_BESL_SUPPORT (1 << 2) /* supports BESL */ +#define USB_BESL_BASELINE_VALID (1 << 3) /* Baseline BESL valid*/ +#define USB_BESL_DEEP_VALID (1 << 4) /* Deep BESL valid */ +#define USB_GET_BESL_BASELINE(p) (((p) & (0xf << 8)) >> 8) +#define USB_GET_BESL_DEEP(p) (((p) & (0xf << 12)) >> 12) +} __attribute__((packed)); + +#define USB_DT_USB_EXT_CAP_SIZE 7 + +/* + * SuperSpeed USB Capability descriptor: Defines the set of SuperSpeed USB + * specific device level capabilities + */ +#define USB_SS_CAP_TYPE 3 +struct usb_ss_cap_descriptor { /* Link Power Management */ + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; + __u8 bmAttributes; +#define USB_LTM_SUPPORT (1 << 1) /* supports LTM */ + __le16 wSpeedSupported; +#define USB_LOW_SPEED_OPERATION (1) /* Low speed operation */ +#define USB_FULL_SPEED_OPERATION (1 << 1) /* Full speed operation */ +#define USB_HIGH_SPEED_OPERATION (1 << 2) /* High speed operation */ +#define USB_5GBPS_OPERATION (1 << 3) /* Operation at 5Gbps */ + __u8 bFunctionalitySupport; + __u8 bU1devExitLat; + __le16 bU2DevExitLat; +} __attribute__((packed)); + +#define USB_DT_USB_SS_CAP_SIZE 10 + +/* + * Container ID Capability descriptor: Defines the instance unique ID used to + * identify the instance across all operating modes + */ +#define CONTAINER_ID_TYPE 4 +struct usb_ss_container_id_descriptor { + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; + __u8 bReserved; + __u8 ContainerID[16]; /* 128-bit number */ +} __attribute__((packed)); + +#define USB_DT_USB_SS_CONTN_ID_SIZE 20 /*-------------------------------------------------------------------------*/ /* USB_DT_WIRELESS_ENDPOINT_COMP: companion descriptor associated with @@ -491,9 +905,22 @@ enum usb_device_speed { USB_SPEED_UNKNOWN = 0, /* enumerating */ USB_SPEED_LOW, USB_SPEED_FULL, /* usb 1.1 */ USB_SPEED_HIGH, /* usb 2.0 */ - USB_SPEED_VARIABLE, /* wireless (usb 2.5) */ + USB_SPEED_WIRELESS, /* wireless (usb 2.5) */ + USB_SPEED_SUPER, /* usb 3.0 */ }; +#ifdef __KERNEL__ + +/** + * usb_speed_string() - Returns human readable-name of the speed. + * @speed: The speed to return human-readable name for. If it's not + * any of the speeds defined in usb_device_speed enum, string for + * USB_SPEED_UNKNOWN will be returned. + */ +extern const char *usb_speed_string(enum usb_device_speed speed); + +#endif + enum usb_device_state { /* NOTATTACHED isn't in the USB spec, and this state acts * the same as ATTACHED ... but it's clearer this way. @@ -503,8 +930,8 @@ enum usb_device_state { /* chapter 9 and authentication (wireless) device states */ USB_STATE_ATTACHED, USB_STATE_POWERED, /* wired */ - USB_STATE_UNAUTHENTICATED, /* auth */ USB_STATE_RECONNECTING, /* auth */ + USB_STATE_UNAUTHENTICATED, /* auth */ USB_STATE_DEFAULT, /* limited function */ USB_STATE_ADDRESS, USB_STATE_CONFIGURED, /* most functions */ @@ -514,7 +941,64 @@ enum usb_device_state { /* NOTE: there are actually four different SUSPENDED * states, returning to POWERED, DEFAULT, ADDRESS, or * CONFIGURED respectively when SOF tokens flow again. + * At this level there's no difference between L1 and L2 + * suspend states. (L2 being original USB 1.1 suspend.) */ }; -#endif /* __LINUX_USB_CH9_H */ +enum usb3_link_state { + USB3_LPM_U0 = 0, + USB3_LPM_U1, + USB3_LPM_U2, + USB3_LPM_U3 +}; + +/* + * A U1 timeout of 0x0 means the parent hub will reject any transitions to U1. + * 0xff means the parent hub will accept transitions to U1, but will not + * initiate a transition. + * + * A U1 timeout of 0x1 to 0x7F also causes the hub to initiate a transition to + * U1 after that many microseconds. Timeouts of 0x80 to 0xFE are reserved + * values. + * + * A U2 timeout of 0x0 means the parent hub will reject any transitions to U2. + * 0xff means the parent hub will accept transitions to U2, but will not + * initiate a transition. + * + * A U2 timeout of 0x1 to 0xFE also causes the hub to initiate a transition to + * U2 after N*256 microseconds. Therefore a U2 timeout value of 0x1 means a U2 + * idle timer of 256 microseconds, 0x2 means 512 microseconds, 0xFE means + * 65.024ms. + */ +#define USB3_LPM_DISABLED 0x0 +#define USB3_LPM_U1_MAX_TIMEOUT 0x7F +#define USB3_LPM_U2_MAX_TIMEOUT 0xFE +#define USB3_LPM_DEVICE_INITIATED 0xFF + +struct usb_set_sel_req { + __u8 u1_sel; + __u8 u1_pel; + __le16 u2_sel; + __le16 u2_pel; +} __attribute__ ((packed)); + +/* + * The Set System Exit Latency control transfer provides one byte each for + * U1 SEL and U1 PEL, so the max exit latency is 0xFF. U2 SEL and U2 PEL each + * are two bytes long. + */ +#define USB3_LPM_MAX_U1_SEL_PEL 0xFF +#define USB3_LPM_MAX_U2_SEL_PEL 0xFFFF + +/*-------------------------------------------------------------------------*/ + +/* + * As per USB compliance update, a device that is actively drawing + * more than 100mA from USB must report itself as bus-powered in + * the GetStatus(DEVICE) call. + * http://compliance.usb.org/index.asp?UpdateFile=Electrical&Format=Standard#34 + */ +#define USB_SELF_POWER_VBUS_MAX_DRAW 100 + +#endif /* __LINUX_USB_CH9_H */ diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h new file mode 100644 index 0000000000..9f65ef96ac --- /dev/null +++ b/include/linux/usb/musb.h @@ -0,0 +1,162 @@ +/* + * This is used to for host and peripheral modes of the driver for + * Inventra (Multidrop) Highspeed Dual-Role Controllers: (M)HDRC. + * + * Board initialization should put one of these into dev->platform_data, + * probably on some platform_device named "musb-hdrc". It encapsulates + * key configuration differences between boards. + */ + +#ifndef __LINUX_USB_MUSB_H +#define __LINUX_USB_MUSB_H + +#ifndef __deprecated +#define __deprecated +#endif + +/* The USB role is defined by the connector used on the board, so long as + * standards are being followed. (Developer boards sometimes won't.) + */ +enum musb_mode { + MUSB_UNDEFINED = 0, + MUSB_HOST, /* A or Mini-A connector */ + MUSB_PERIPHERAL, /* B or Mini-B connector */ + MUSB_OTG /* Mini-AB connector */ +}; + +struct clk; + +enum musb_fifo_style { + FIFO_RXTX, + FIFO_TX, + FIFO_RX +} __attribute__ ((packed)); + +enum musb_buf_mode { + BUF_SINGLE, + BUF_DOUBLE +} __attribute__ ((packed)); + +struct musb_fifo_cfg { + u8 hw_ep_num; + enum musb_fifo_style style; + enum musb_buf_mode mode; + u16 maxpacket; +}; + +#define MUSB_EP_FIFO(ep, st, m, pkt) \ +{ \ + .hw_ep_num = ep, \ + .style = st, \ + .mode = m, \ + .maxpacket = pkt, \ +} + +#define MUSB_EP_FIFO_SINGLE(ep, st, pkt) \ + MUSB_EP_FIFO(ep, st, BUF_SINGLE, pkt) + +#define MUSB_EP_FIFO_DOUBLE(ep, st, pkt) \ + MUSB_EP_FIFO(ep, st, BUF_DOUBLE, pkt) + +struct musb_hdrc_eps_bits { + const char name[16]; + u8 bits; +}; + +struct musb_hdrc_config { + struct musb_fifo_cfg *fifo_cfg; /* board fifo configuration */ + unsigned fifo_cfg_size; /* size of the fifo configuration */ + + /* MUSB configuration-specific details */ + unsigned multipoint:1; /* multipoint device */ + unsigned dyn_fifo:1 __deprecated; /* supports dynamic fifo sizing */ + unsigned soft_con:1 __deprecated; /* soft connect required */ + unsigned utm_16:1 __deprecated; /* utm data witdh is 16 bits */ + unsigned big_endian:1; /* true if CPU uses big-endian */ + unsigned mult_bulk_tx:1; /* Tx ep required for multbulk pkts */ + unsigned mult_bulk_rx:1; /* Rx ep required for multbulk pkts */ + unsigned high_iso_tx:1; /* Tx ep required for HB iso */ + unsigned high_iso_rx:1; /* Rx ep required for HD iso */ + unsigned dma:1 __deprecated; /* supports DMA */ + unsigned vendor_req:1 __deprecated; /* vendor registers required */ + + u8 num_eps; /* number of endpoints _with_ ep0 */ + u8 dma_channels __deprecated; /* number of dma channels */ + u8 dyn_fifo_size; /* dynamic size in bytes */ + u8 vendor_ctrl __deprecated; /* vendor control reg width */ + u8 vendor_stat __deprecated; /* vendor status reg witdh */ + u8 dma_req_chan __deprecated; /* bitmask for required dma channels */ + u8 ram_bits; /* ram address size */ + + struct musb_hdrc_eps_bits *eps_bits __deprecated; +#ifdef CONFIG_BLACKFIN + /* A GPIO controlling VRSEL in Blackfin */ + unsigned int gpio_vrsel; + unsigned int gpio_vrsel_active; + /* musb CLKIN in Blackfin in MHZ */ + unsigned char clkin; +#endif + +}; + +struct musb_hdrc_platform_data { + /* MUSB_HOST, MUSB_PERIPHERAL, or MUSB_OTG */ + u8 mode; + + /* for clk_get() */ + const char *clock; + + /* (HOST or OTG) switch VBUS on/off */ + int (*set_vbus)(struct device *dev, int is_on); + + /* (HOST or OTG) mA/2 power supplied on (default = 8mA) */ + u8 power; + + /* (PERIPHERAL) mA/2 max power consumed (default = 100mA) */ + u8 min_power; + + /* (HOST or OTG) msec/2 after VBUS on till power good */ + u8 potpgt; + + /* (HOST or OTG) program PHY for external Vbus */ + unsigned extvbus:1; + + /* Power the device on or off */ + int (*set_power)(int state); + + /* MUSB configuration-specific details */ + struct musb_hdrc_config *config; + + /* Architecture specific board data */ + void *board_data; + + /* Platform specific struct musb_ops pointer */ + const void *platform_ops; +}; + + +/* TUSB 6010 support */ + +#define TUSB6010_OSCCLK_60 16667 /* psec/clk @ 60.0 MHz */ +#define TUSB6010_REFCLK_24 41667 /* psec/clk @ 24.0 MHz XI */ +#define TUSB6010_REFCLK_19 52083 /* psec/clk @ 19.2 MHz CLKIN */ + +#ifdef CONFIG_ARCH_OMAP2 + +extern int __init tusb6010_setup_interface( + struct musb_hdrc_platform_data *data, + unsigned ps_refclk, unsigned waitpin, + unsigned async_cs, unsigned sync_cs, + unsigned irq, unsigned dmachan); + +extern int tusb6010_platform_retime(unsigned is_refclk); + +#endif /* OMAP2 */ + +/* + * U-Boot specfic stuff + */ +int musb_register(struct musb_hdrc_platform_data *plat, void *bdata, + void *ctl_regs); + +#endif /* __LINUX_USB_MUSB_H */ diff --git a/include/nand.h b/include/nand.h index bbe28b20bb..dded4e27f0 100644 --- a/include/nand.h +++ b/include/nand.h @@ -139,6 +139,7 @@ int nand_read_skip_bad(nand_info_t *nand, loff_t offset, size_t *length, int nand_write_skip_bad(nand_info_t *nand, loff_t offset, size_t *length, u_char *buffer, int flags); int nand_erase_opts(nand_info_t *meminfo, const nand_erase_options_t *opts); +int nand_torture(nand_info_t *nand, loff_t offset); #define NAND_LOCK_STATUS_TIGHT 0x01 #define NAND_LOCK_STATUS_UNLOCK 0x04 diff --git a/include/nios2.h b/include/nios2.h index df8126a66e..cbca0dc01f 100644 --- a/include/nios2.h +++ b/include/nios2.h @@ -24,8 +24,6 @@ #ifndef __NIOS2_H__ #define __NIOS2_H__ -#include <linux/stringify.h> - /*------------------------------------------------------------------------ * Control registers -- use with wrctl() & rdctl() *----------------------------------------------------------------------*/ @@ -39,14 +37,8 @@ * Access to control regs *----------------------------------------------------------------------*/ -#define rdctl(reg)\ - ({unsigned int val;\ - asm volatile("rdctl %0, ctl" __stringify(reg) \ - : "=r" (val) ); val;}) - -#define wrctl(reg,val)\ - asm volatile( "wrctl ctl" _str_(reg) ",%0"\ - : : "r" (val)) +#define rdctl(reg) __builtin_rdctl(reg) +#define wrctl(reg, val) __builtin_wrctl(reg, val) /*------------------------------------------------------------------------ * Control reg bit masks diff --git a/include/pci.h b/include/pci.h index eba122f8c0..15f583f069 100644 --- a/include/pci.h +++ b/include/pci.h @@ -67,7 +67,130 @@ #define PCI_CLASS_PROG 0x09 /* Reg. Level Programming Interface */ #define PCI_CLASS_DEVICE 0x0a /* Device class */ #define PCI_CLASS_CODE 0x0b /* Device class code */ +#define PCI_CLASS_CODE_TOO_OLD 0x00 +#define PCI_CLASS_CODE_STORAGE 0x01 +#define PCI_CLASS_CODE_NETWORK 0x02 +#define PCI_CLASS_CODE_DISPLAY 0x03 +#define PCI_CLASS_CODE_MULTIMEDIA 0x04 +#define PCI_CLASS_CODE_MEMORY 0x05 +#define PCI_CLASS_CODE_BRIDGE 0x06 +#define PCI_CLASS_CODE_COMM 0x07 +#define PCI_CLASS_CODE_PERIPHERAL 0x08 +#define PCI_CLASS_CODE_INPUT 0x09 +#define PCI_CLASS_CODE_DOCKING 0x0A +#define PCI_CLASS_CODE_PROCESSOR 0x0B +#define PCI_CLASS_CODE_SERIAL 0x0C +#define PCI_CLASS_CODE_WIRELESS 0x0D +#define PCI_CLASS_CODE_I2O 0x0E +#define PCI_CLASS_CODE_SATELLITE 0x0F +#define PCI_CLASS_CODE_CRYPTO 0x10 +#define PCI_CLASS_CODE_DATA 0x11 +/* Base Class 0x12 - 0xFE is reserved */ +#define PCI_CLASS_CODE_OTHER 0xFF + #define PCI_CLASS_SUB_CODE 0x0a /* Device sub-class code */ +#define PCI_CLASS_SUB_CODE_TOO_OLD_NOTVGA 0x00 +#define PCI_CLASS_SUB_CODE_TOO_OLD_VGA 0x01 +#define PCI_CLASS_SUB_CODE_STORAGE_SCSI 0x00 +#define PCI_CLASS_SUB_CODE_STORAGE_IDE 0x01 +#define PCI_CLASS_SUB_CODE_STORAGE_FLOPPY 0x02 +#define PCI_CLASS_SUB_CODE_STORAGE_IPIBUS 0x03 +#define PCI_CLASS_SUB_CODE_STORAGE_RAID 0x04 +#define PCI_CLASS_SUB_CODE_STORAGE_ATA 0x05 +#define PCI_CLASS_SUB_CODE_STORAGE_SATA 0x06 +#define PCI_CLASS_SUB_CODE_STORAGE_SAS 0x07 +#define PCI_CLASS_SUB_CODE_STORAGE_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_NETWORK_ETHERNET 0x00 +#define PCI_CLASS_SUB_CODE_NETWORK_TOKENRING 0x01 +#define PCI_CLASS_SUB_CODE_NETWORK_FDDI 0x02 +#define PCI_CLASS_SUB_CODE_NETWORK_ATM 0x03 +#define PCI_CLASS_SUB_CODE_NETWORK_ISDN 0x04 +#define PCI_CLASS_SUB_CODE_NETWORK_WORLDFIP 0x05 +#define PCI_CLASS_SUB_CODE_NETWORK_PICMG 0x06 +#define PCI_CLASS_SUB_CODE_NETWORK_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_DISPLAY_VGA 0x00 +#define PCI_CLASS_SUB_CODE_DISPLAY_XGA 0x01 +#define PCI_CLASS_SUB_CODE_DISPLAY_3D 0x02 +#define PCI_CLASS_SUB_CODE_DISPLAY_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_MULTIMEDIA_VIDEO 0x00 +#define PCI_CLASS_SUB_CODE_MULTIMEDIA_AUDIO 0x01 +#define PCI_CLASS_SUB_CODE_MULTIMEDIA_PHONE 0x02 +#define PCI_CLASS_SUB_CODE_MULTIMEDIA_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_MEMORY_RAM 0x00 +#define PCI_CLASS_SUB_CODE_MEMORY_FLASH 0x01 +#define PCI_CLASS_SUB_CODE_MEMORY_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_BRIDGE_HOST 0x00 +#define PCI_CLASS_SUB_CODE_BRIDGE_ISA 0x01 +#define PCI_CLASS_SUB_CODE_BRIDGE_EISA 0x02 +#define PCI_CLASS_SUB_CODE_BRIDGE_MCA 0x03 +#define PCI_CLASS_SUB_CODE_BRIDGE_PCI 0x04 +#define PCI_CLASS_SUB_CODE_BRIDGE_PCMCIA 0x05 +#define PCI_CLASS_SUB_CODE_BRIDGE_NUBUS 0x06 +#define PCI_CLASS_SUB_CODE_BRIDGE_CARDBUS 0x07 +#define PCI_CLASS_SUB_CODE_BRIDGE_RACEWAY 0x08 +#define PCI_CLASS_SUB_CODE_BRIDGE_SEMI_PCI 0x09 +#define PCI_CLASS_SUB_CODE_BRIDGE_INFINIBAND 0x0A +#define PCI_CLASS_SUB_CODE_BRIDGE_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_COMM_SERIAL 0x00 +#define PCI_CLASS_SUB_CODE_COMM_PARALLEL 0x01 +#define PCI_CLASS_SUB_CODE_COMM_MULTIPORT 0x02 +#define PCI_CLASS_SUB_CODE_COMM_MODEM 0x03 +#define PCI_CLASS_SUB_CODE_COMM_GPIB 0x04 +#define PCI_CLASS_SUB_CODE_COMM_SMARTCARD 0x05 +#define PCI_CLASS_SUB_CODE_COMM_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_PERIPHERAL_PIC 0x00 +#define PCI_CLASS_SUB_CODE_PERIPHERAL_DMA 0x01 +#define PCI_CLASS_SUB_CODE_PERIPHERAL_TIMER 0x02 +#define PCI_CLASS_SUB_CODE_PERIPHERAL_RTC 0x03 +#define PCI_CLASS_SUB_CODE_PERIPHERAL_HOTPLUG 0x04 +#define PCI_CLASS_SUB_CODE_PERIPHERAL_SD 0x05 +#define PCI_CLASS_SUB_CODE_PERIPHERAL_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_INPUT_KEYBOARD 0x00 +#define PCI_CLASS_SUB_CODE_INPUT_DIGITIZER 0x01 +#define PCI_CLASS_SUB_CODE_INPUT_MOUSE 0x02 +#define PCI_CLASS_SUB_CODE_INPUT_SCANNER 0x03 +#define PCI_CLASS_SUB_CODE_INPUT_GAMEPORT 0x04 +#define PCI_CLASS_SUB_CODE_INPUT_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_DOCKING_GENERIC 0x00 +#define PCI_CLASS_SUB_CODE_DOCKING_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_PROCESSOR_386 0x00 +#define PCI_CLASS_SUB_CODE_PROCESSOR_486 0x01 +#define PCI_CLASS_SUB_CODE_PROCESSOR_PENTIUM 0x02 +#define PCI_CLASS_SUB_CODE_PROCESSOR_ALPHA 0x10 +#define PCI_CLASS_SUB_CODE_PROCESSOR_POWERPC 0x20 +#define PCI_CLASS_SUB_CODE_PROCESSOR_MIPS 0x30 +#define PCI_CLASS_SUB_CODE_PROCESSOR_COPROC 0x40 +#define PCI_CLASS_SUB_CODE_SERIAL_1394 0x00 +#define PCI_CLASS_SUB_CODE_SERIAL_ACCESSBUS 0x01 +#define PCI_CLASS_SUB_CODE_SERIAL_SSA 0x02 +#define PCI_CLASS_SUB_CODE_SERIAL_USB 0x03 +#define PCI_CLASS_SUB_CODE_SERIAL_FIBRECHAN 0x04 +#define PCI_CLASS_SUB_CODE_SERIAL_SMBUS 0x05 +#define PCI_CLASS_SUB_CODE_SERIAL_INFINIBAND 0x06 +#define PCI_CLASS_SUB_CODE_SERIAL_IPMI 0x07 +#define PCI_CLASS_SUB_CODE_SERIAL_SERCOS 0x08 +#define PCI_CLASS_SUB_CODE_SERIAL_CANBUS 0x09 +#define PCI_CLASS_SUB_CODE_WIRELESS_IRDA 0x00 +#define PCI_CLASS_SUB_CODE_WIRELESS_IR 0x01 +#define PCI_CLASS_SUB_CODE_WIRELESS_RF 0x10 +#define PCI_CLASS_SUB_CODE_WIRELESS_BLUETOOTH 0x11 +#define PCI_CLASS_SUB_CODE_WIRELESS_BROADBAND 0x12 +#define PCI_CLASS_SUB_CODE_WIRELESS_80211A 0x20 +#define PCI_CLASS_SUB_CODE_WIRELESS_80211B 0x21 +#define PCI_CLASS_SUB_CODE_WIRELESS_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_I2O_V1_0 0x00 +#define PCI_CLASS_SUB_CODE_SATELLITE_TV 0x01 +#define PCI_CLASS_SUB_CODE_SATELLITE_AUDIO 0x02 +#define PCI_CLASS_SUB_CODE_SATELLITE_VOICE 0x03 +#define PCI_CLASS_SUB_CODE_SATELLITE_DATA 0x04 +#define PCI_CLASS_SUB_CODE_CRYPTO_NETWORK 0x00 +#define PCI_CLASS_SUB_CODE_CRYPTO_ENTERTAINMENT 0x10 +#define PCI_CLASS_SUB_CODE_CRYPTO_OTHER 0x80 +#define PCI_CLASS_SUB_CODE_DATA_DPIO 0x00 +#define PCI_CLASS_SUB_CODE_DATA_PERFCNTR 0x01 +#define PCI_CLASS_SUB_CODE_DATA_COMMSYNC 0x10 +#define PCI_CLASS_SUB_CODE_DATA_MGMT 0x20 +#define PCI_CLASS_SUB_CODE_DATA_OTHER 0x80 #define PCI_CACHE_LINE_SIZE 0x0c /* 8 bits */ #define PCI_LATENCY_TIMER 0x0d /* 8 bits */ diff --git a/include/physmem.h b/include/physmem.h new file mode 100644 index 0000000000..03d3a78b74 --- /dev/null +++ b/include/physmem.h @@ -0,0 +1,21 @@ +/* + * Copyright (c) 2012 The Chromium OS Authors. All rights reserved. + * Use of this source code is governed by a BSD-style license that can be + * found in the LICENSE file. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + */ + +/* + * These functions work like memset but operate on physical memory which may + * not be accessible directly. + * + * @param s The physical address to start setting memory at. + * @param c The character to set each byte of the region to. + * @param n The number of bytes to set. + * + * @return The physical address of the memory which was set. + */ +phys_addr_t arch_phys_memset(phys_addr_t s, int c, phys_size_t n); diff --git a/include/power/battery.h b/include/power/battery.h new file mode 100644 index 0000000000..e2fec687da --- /dev/null +++ b/include/power/battery.h @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2012 Samsung Electronics + * Lukasz Majewski <l.majewski@samsung.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __POWER_BATTERY_H_ +#define __POWER_BATTERY_H_ + +struct battery { + unsigned int version; + unsigned int state_of_chrg; + unsigned int time_to_empty; + unsigned int capacity; + unsigned int voltage_uV; + + unsigned int state; +}; + +int power_bat_init(unsigned char bus); +#endif /* __POWER_BATTERY_H_ */ diff --git a/include/power/fg_battery_cell_params.h b/include/power/fg_battery_cell_params.h new file mode 100644 index 0000000000..7ddf6f2ffa --- /dev/null +++ b/include/power/fg_battery_cell_params.h @@ -0,0 +1,90 @@ +/* + * Copyright (C) 2012 Samsung Electronics + * Lukasz Majewski <l.majewski@samsung.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __FG_BATTERY_CELL_PARAMS_H_ +#define __FG_BATTERY_CELL_PARAMS_H_ + +#if defined(CONFIG_POWER_FG_MAX17042) && defined(CONFIG_TRATS) + +/* Cell characteristics - Exynos4 TRATS development board */ +/* Shall be written to addr 0x80h */ +u16 cell_character0[16] = { + 0xA2A0, + 0xB6E0, + 0xB850, + 0xBAD0, + 0xBB20, + 0xBB70, + 0xBBC0, + 0xBC20, + 0xBC80, + 0xBCE0, + 0xBD80, + 0xBE20, + 0xC090, + 0xC420, + 0xC910, + 0xD070 +}; + +/* Shall be written to addr 0x90h */ +u16 cell_character1[16] = { + 0x0090, + 0x1A50, + 0x02F0, + 0x2060, + 0x2060, + 0x2E60, + 0x26A0, + 0x2DB0, + 0x2DB0, + 0x1870, + 0x2A20, + 0x16F0, + 0x08F0, + 0x0D40, + 0x08C0, + 0x08C0 +}; + +/* Shall be written to addr 0xA0h */ +u16 cell_character2[16] = { + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100, + 0x0100 +}; +#endif +#endif /* __FG_BATTERY_CELL_PARAMS_H_ */ diff --git a/include/power/max17042_fg.h b/include/power/max17042_fg.h new file mode 100644 index 0000000000..1103a483f2 --- /dev/null +++ b/include/power/max17042_fg.h @@ -0,0 +1,74 @@ +/* + * Copyright (C) 2012 Samsung Electronics + * Lukasz Majewski <l.majewski@samsung.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __MAX17042_FG_H_ +#define __MAX17042_FG_H_ + +/* MAX 17042 registers */ +enum { + MAX17042_STATUS = 0x00, + MAX17042_SOCREP = 0x06, + MAX17042_VCELL = 0x09, + MAX17042_CURRENT = 0x0A, + MAX17042_AVG_CURRENT = 0x0B, + MAX17042_SOCMIX = 0x0D, + MAX17042_SOCAV = 0x0E, + MAX17042_DESIGN_CAP = 0x18, + MAX17042_AVG_VCELL = 0x19, + MAX17042_CONFIG = 0x1D, + MAX17042_VERSION = 0x21, + MAX17042_LEARNCFG = 0x28, + MAX17042_FILTERCFG = 0x29, + MAX17042_RELAXCFG = 0x2A, + MAX17042_MISCCFG = 0x2B, + MAX17042_CGAIN = 0x2E, + MAX17042_COFF = 0x2F, + MAX17042_RCOMP0 = 0x38, + MAX17042_TEMPCO = 0x39, + MAX17042_FSTAT = 0x3D, + MAX17042_MLOCKReg1 = 0x62, + MAX17042_MLOCKReg2 = 0x63, + MAX17042_MODEL1 = 0x80, + MAX17042_MODEL2 = 0x90, + MAX17042_MODEL3 = 0xA0, + MAX17042_VFOCV = 0xFB, + MAX17042_VFSOC = 0xFF, + + FG_NUM_OF_REGS = 0x100, +}; + +#define RCOMP0 0x0060 +#define TempCo 0x1015 + + +#define MAX17042_POR (1 << 1) + +#define MODEL_UNLOCK1 0x0059 +#define MODEL_UNLOCK2 0x00c4 +#define MODEL_LOCK1 0x0000 +#define MODEL_LOCK2 0x0000 + +#define MAX17042_I2C_ADDR (0x6C >> 1) + +int power_fg_init(unsigned char bus); +#endif /* __MAX17042_FG_H_ */ diff --git a/include/power/max8997_muic.h b/include/power/max8997_muic.h new file mode 100644 index 0000000000..0149c12435 --- /dev/null +++ b/include/power/max8997_muic.h @@ -0,0 +1,61 @@ +/* + * Copyright (C) 2012 Samsung Electronics + * Lukasz Majewski <l.majewski@samsung.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __MAX8997_MUIC_H_ +#define __MAX8997_MUIC_H_ + +#include <power/power_chrg.h> + +/* MAX8997_MUIC_STATUS2 */ +#define MAX8997_MUIC_CHG_NO 0x00 +#define MAX8997_MUIC_CHG_USB 0x01 +#define MAX8997_MUIC_CHG_USB_D 0x02 +#define MAX8997_MUIC_CHG_TA 0x03 +#define MAX8997_MUIC_CHG_TA_500 0x04 +#define MAX8997_MUIC_CHG_TA_1A 0x05 +#define MAX8997_MUIC_CHG_MASK 0x07 + +/* MAX 8997 MUIC registers */ +enum { + MAX8997_MUIC_ID = 0x00, + MAX8997_MUIC_INT1 = 0x01, + MAX8997_MUIC_INT2 = 0x02, + MAX8997_MUIC_INT3 = 0x03, + MAX8997_MUIC_STATUS1 = 0x04, + MAX8997_MUIC_STATUS2 = 0x05, + MAX8997_MUIC_STATUS3 = 0x06, + MAX8997_MUIC_INTMASK1 = 0x07, + MAX8997_MUIC_INTMASK2 = 0x08, + MAX8997_MUIC_INTMASK3 = 0x09, + MAX8997_MUIC_CDETCTRL = 0x0A, + MAX8997_MUIC_CONTROL1 = 0x0C, + MAX8997_MUIC_CONTROL2 = 0x0D, + MAX8997_MUIC_CONTROL3 = 0x0E, + + MUIC_NUM_OF_REGS = 0x0F, +}; + +#define MAX8997_MUIC_I2C_ADDR (0x4A >> 1) + +int power_muic_init(unsigned int bus); +#endif /* __MAX8997_MUIC_H_ */ diff --git a/include/max8997_pmic.h b/include/power/max8997_pmic.h index 17ae24ea6a..5d2d94df9b 100644 --- a/include/max8997_pmic.h +++ b/include/power/max8997_pmic.h @@ -111,7 +111,7 @@ enum { MAX8997_REG_MBCCTRL6 = 0x55, MAX8997_REG_OTPCGHCVS = 0x56, - MAX8997_REG_SAFEOUTCTRL = 0x5a, + MAX8997_REG_SAFEOUTCTRL = 0x5a, MAX8997_REG_LBCNFG1 = 0x5e, MAX8997_REG_LBCNFG2 = 0x5f, @@ -171,9 +171,31 @@ enum { PMIC_NUM_OF_REGS = 0x9b, }; +#define ACTDISSAFEO1 (1 << 4) +#define ACTDISSAFEO2 (1 << 5) #define ENSAFEOUT1 (1 << 6) #define ENSAFEOUT2 (1 << 7) +#define ENBUCK (1 << 0) +#define ACTIVE_DISCHARGE (1 << 3) +#define GNSLCT (1 << 2) +#define LDO_ADE (1 << 1) +#define SAFEOUT_4_85V 0x00 +#define SAFEOUT_4_90V 0x01 +#define SAFEOUT_4_95V 0x02 +#define SAFEOUT_3_30V 0x03 + +/* Charger */ +enum {CHARGER_ENABLE, CHARGER_DISABLE}; +#define DETBAT (1 << 2) +#define MBCICHFCSET (1 << 4) +#define MBCHOSTEN (1 << 6) +#define VCHGR_FC (1 << 7) + +#define CHARGER_MIN_CURRENT 200 +#define CHARGER_MAX_CURRENT 950 +#define CHARGER_CURRENT_RESOLUTION 50 + #define MAX8997_I2C_ADDR (0xCC >> 1) #define MAX8997_RTC_ADDR (0x0C >> 1) #define MAX8997_MUIC_ADDR (0x4A >> 1) @@ -187,4 +209,6 @@ enum { EN_LDO = (0x3 << 6), }; +#define MAX8997_LDO_MAX_VAL 0x3F +unsigned char max8997_reg_ldo(int uV); #endif /* __MAX8997_PMIC_H_ */ diff --git a/include/max8998_pmic.h b/include/power/max8998_pmic.h index ca21f882c2..ca21f882c2 100644 --- a/include/max8998_pmic.h +++ b/include/power/max8998_pmic.h diff --git a/include/pmic.h b/include/power/pmic.h index 6a05b40aef..1ecfc0543c 100644 --- a/include/pmic.h +++ b/include/power/pmic.h @@ -1,5 +1,5 @@ /* - * Copyright (C) 2011 Samsung Electronics + * Copyright (C) 2011-2012 Samsung Electronics * Lukasz Majewski <l.majewski@samsung.com> * * See file CREDITS for list of people who contributed to this @@ -24,9 +24,15 @@ #ifndef __CORE_PMIC_H_ #define __CORE_PMIC_H_ -enum { PMIC_I2C, PMIC_SPI, }; +#include <common.h> +#include <linux/list.h> +#include <i2c.h> +#include <power/power_chrg.h> + +enum { PMIC_I2C, PMIC_SPI, PMIC_NONE}; enum { I2C_PMIC, I2C_NUM, }; enum { PMIC_READ, PMIC_WRITE, }; +enum { PMIC_SENSOR_BYTE_ORDER_LITTLE, PMIC_SENSOR_BYTE_ORDER_BIG, }; struct p_i2c { unsigned char addr; @@ -43,21 +49,52 @@ struct p_spi { u32 (*prepare_tx)(u32 reg, u32 *val, u32 write); }; +struct pmic; +struct power_fg { + int (*fg_battery_check) (struct pmic *p, struct pmic *bat); + int (*fg_battery_update) (struct pmic *p, struct pmic *bat); +}; + +struct power_chrg { + int (*chrg_type) (struct pmic *p); + int (*chrg_bat_present) (struct pmic *p); + int (*chrg_state) (struct pmic *p, int state, int current); +}; + +struct power_battery { + struct battery *bat; + int (*battery_init) (struct pmic *bat, struct pmic *p1, + struct pmic *p2, struct pmic *p3); + int (*battery_charge) (struct pmic *bat); + /* Keep info about power devices involved with battery operation */ + struct pmic *chrg, *fg, *muic; +}; + struct pmic { const char *name; unsigned char bus; unsigned char interface; - unsigned char number_of_regs; + unsigned char sensor_byte_order; + unsigned int number_of_regs; union hw { struct p_i2c i2c; struct p_spi spi; } hw; + + void (*low_power_mode) (void); + struct power_battery *pbat; + struct power_chrg *chrg; + struct power_fg *fg; + + struct pmic *parent; + struct list_head list; }; -int pmic_init(void); -int pmic_dialog_init(void); -int check_reg(u32 reg); -struct pmic *get_pmic(void); +int pmic_init(unsigned char bus); +int pmic_dialog_init(unsigned char bus); +int check_reg(struct pmic *p, u32 reg); +struct pmic *pmic_alloc(void); +struct pmic *pmic_get(const char *s); int pmic_probe(struct pmic *p); int pmic_reg_read(struct pmic *p, u32 reg, u32 *val); int pmic_reg_write(struct pmic *p, u32 reg, u32 val); diff --git a/include/power/power_chrg.h b/include/power/power_chrg.h new file mode 100644 index 0000000000..24c4cde739 --- /dev/null +++ b/include/power/power_chrg.h @@ -0,0 +1,43 @@ +/* + * Copyright (C) 2012 Samsung Electronics + * Lukasz Majewski <l.majewski@samsung.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __POWER_CHARGER_H_ +#define __POWER_CHARGER_H_ + +/* Type of available chargers */ +enum { + CHARGER_NO = 0, + CHARGER_TA, + CHARGER_USB, + CHARGER_TA_500, + CHARGER_UNKNOWN, +}; + +enum { + UNKNOWN, + EXT_SOURCE, + CHARGE, + NORMAL, +}; + +#endif /* __POWER_CHARGER_H_ */ diff --git a/include/sdhci.h b/include/sdhci.h index c44793d5ec..cffbe53621 100644 --- a/include/sdhci.h +++ b/include/sdhci.h @@ -225,6 +225,7 @@ #define SDHCI_QUIRK_BROKEN_VOLTAGE (1 << 4) #define SDHCI_QUIRK_NO_CD (1 << 5) #define SDHCI_QUIRK_WAIT_SEND_CMD (1 << 6) +#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER (1 << 7) /* to make gcc happy */ struct sdhci_host; diff --git a/include/status_led.h b/include/status_led.h index da9fae9203..27e9127694 100644 --- a/include/status_led.h +++ b/include/status_led.h @@ -273,9 +273,6 @@ void status_led_set (int led, int state); #elif defined(CONFIG_STXXTC) /* XXX empty just to avoid the error */ /************************************************************************/ -#elif defined(CONFIG_NIOS2) -/* XXX empty just to avoid the error */ -/************************************************************************/ #elif defined(CONFIG_V38B) # define STATUS_LED_BIT 0x0010 /* Timer7 GPIO */ diff --git a/include/stdio_dev.h b/include/stdio_dev.h index 23e0ee15f2..932d093345 100644 --- a/include/stdio_dev.h +++ b/include/stdio_dev.h @@ -120,5 +120,8 @@ int drv_nc_init (void); #ifdef CONFIG_JTAG_CONSOLE int drv_jtag_console_init (void); #endif +#ifdef CONFIG_CBMEM_CONSOLE +int cbmemc_init(void); +#endif #endif diff --git a/include/usb.h b/include/usb.h index 9dd8791947..8d8a2c9b9d 100644 --- a/include/usb.h +++ b/include/usb.h @@ -27,7 +27,7 @@ #define _USB_H_ #include <usb_defs.h> -#include <usbdescriptors.h> +#include <linux/usb/ch9.h> /* * The EHCI spec says that we must align to at least 32 bytes. However, @@ -67,12 +67,6 @@ struct devrequest { unsigned short length; } __attribute__ ((packed)); -/* All standard descriptors have these 2 fields in common */ -struct usb_descriptor_header { - unsigned char bLength; - unsigned char bDescriptorType; -} __attribute__ ((packed)); - /* Interface */ struct usb_interface { struct usb_interface_descriptor desc; @@ -86,7 +80,7 @@ struct usb_interface { /* Configuration information.. */ struct usb_config { - struct usb_configuration_descriptor desc; + struct usb_config_descriptor desc; unsigned char no_of_if; /* number of interfaces */ struct usb_interface if_desc[USB_MAXINTERFACES]; @@ -153,7 +147,9 @@ struct usb_device { defined(CONFIG_USB_SL811HS) || defined(CONFIG_USB_ISP116X_HCD) || \ defined(CONFIG_USB_R8A66597_HCD) || defined(CONFIG_USB_DAVINCI) || \ defined(CONFIG_USB_OMAP3) || defined(CONFIG_USB_DA8XX) || \ - defined(CONFIG_USB_BLACKFIN) || defined(CONFIG_USB_AM35X) + defined(CONFIG_USB_BLACKFIN) || defined(CONFIG_USB_AM35X) || \ + defined(CONFIG_USB_MUSB_DSPS) || defined(CONFIG_USB_MUSB_AM35X) || \ + defined(CONFIG_USB_MUSB_OMAP2PLUS) int usb_lowlevel_init(int index, void **controller); int usb_lowlevel_stop(int index); @@ -285,7 +281,6 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate); * - device: bits 8-14 * - endpoint: bits 15-18 * - Data0/1: bit 19 - * - speed: bit 26 (0 = Full, 1 = Low Speed, 2 = High) * - pipe type: bits 30-31 (00 = isochronous, 01 = interrupt, * 10 = control, 11 = bulk) * @@ -297,7 +292,7 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate); /* Create various pipes... */ #define create_pipe(dev,endpoint) \ (((dev)->devnum << 8) | ((endpoint) << 15) | \ - ((dev)->speed << 26) | (dev)->maxpacketsize) + (dev)->maxpacketsize) #define default_pipe(dev) ((dev)->speed << 26) #define usb_sndctrlpipe(dev, endpoint) ((PIPE_CONTROL << 30) | \ @@ -348,8 +343,6 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate); #define usb_pipe_endpdev(pipe) (((pipe) >> 8) & 0x7ff) #define usb_pipeendpoint(pipe) (((pipe) >> 15) & 0xf) #define usb_pipedata(pipe) (((pipe) >> 19) & 1) -#define usb_pipespeed(pipe) (((pipe) >> 26) & 3) -#define usb_pipeslow(pipe) (usb_pipespeed(pipe) == USB_SPEED_LOW) #define usb_pipetype(pipe) (((pipe) >> 30) & 3) #define usb_pipeisoc(pipe) (usb_pipetype((pipe)) == PIPE_ISOCHRONOUS) #define usb_pipeint(pipe) (usb_pipetype((pipe)) == PIPE_INTERRUPT) diff --git a/include/usb/s3c_udc.h b/include/usb/s3c_udc.h index 6a8fd44244..7114dae75d 100644 --- a/include/usb/s3c_udc.h +++ b/include/usb/s3c_udc.h @@ -24,7 +24,6 @@ #include <asm/errno.h> #include <linux/usb/ch9.h> -#include <usbdescriptors.h> #include <linux/usb/gadget.h> #include <linux/list.h> #include <usb/lin_gadget_compat.h> diff --git a/include/usb_defs.h b/include/usb_defs.h index 8032e57125..9502544b21 100644 --- a/include/usb_defs.h +++ b/include/usb_defs.h @@ -80,12 +80,6 @@ #define USB_DIR_OUT 0 #define USB_DIR_IN 0x80 -/* USB device speeds */ -#define USB_SPEED_FULL 0x0 /* 12Mbps */ -#define USB_SPEED_LOW 0x1 /* 1.5Mbps */ -#define USB_SPEED_HIGH 0x2 /* 480Mbps */ -#define USB_SPEED_RESERVED 0x3 - /* Descriptor types */ #define USB_DT_DEVICE 0x01 #define USB_DT_CONFIG 0x02 diff --git a/include/video.h b/include/video.h index 9519ceaf98..f7e27f8477 100644 --- a/include/video.h +++ b/include/video.h @@ -15,4 +15,52 @@ int video_init (void *videobase); void video_putc (const char c); void video_puts (const char *s); +/** + * Display a BMP format bitmap on the screen + * + * @param bmp_image Address of BMP image + * @param x X position to draw image + * @param y Y position to draw image + */ +int video_display_bitmap(ulong bmp_image, int x, int y); + +/** + * Get the width of the screen in pixels + * + * @return width of screen in pixels + */ +int video_get_pixel_width(void); + +/** + * Get the height of the screen in pixels + * + * @return height of screen in pixels + */ +int video_get_pixel_height(void); + +/** + * Get the number of text lines/rows on the screen + * + * @return number of rows + */ +int video_get_screen_rows(void); + +/** + * Get the number of text columns on the screen + * + * @return number of columns + */ +int video_get_screen_columns(void); + +/** + * Set the position of the text cursor + * + * @param col Column to place cursor (0 = left side) + * @param row Row to place cursor (0 = top line) + */ +void video_position_cursor(unsigned col, unsigned row); + +/* Clear the display */ +void video_clear(void); + #endif |