diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/asm-arm/arch-davinci/gpio_defs.h | 14 | ||||
| -rw-r--r-- | include/asm-blackfin/mach-common/bits/usb.h | 264 | ||||
| -rw-r--r-- | include/configs/da830evm.h | 38 | ||||
| -rw-r--r-- | include/configs/sequoia.h | 16 | ||||
| -rw-r--r-- | include/usb.h | 3 |
5 files changed, 328 insertions, 7 deletions
diff --git a/include/asm-arm/arch-davinci/gpio_defs.h b/include/asm-arm/arch-davinci/gpio_defs.h index ff629761b5..1be2ac2660 100644 --- a/include/asm-arm/arch-davinci/gpio_defs.h +++ b/include/asm-arm/arch-davinci/gpio_defs.h @@ -22,12 +22,21 @@ #ifndef _GPIO_DEFS_H_ #define _GPIO_DEFS_H_ +#ifndef CONFIG_SOC_DA8XX #define DAVINCI_GPIO_BINTEN 0x01C67008 #define DAVINCI_GPIO_BANK01 0x01C67010 #define DAVINCI_GPIO_BANK23 0x01C67038 #define DAVINCI_GPIO_BANK45 0x01C67060 #define DAVINCI_GPIO_BANK67 0x01C67088 +#else /* CONFIG_SOC_DA8XX */ +#define DAVINCI_GPIO_BINTEN 0x01E26008 +#define DAVINCI_GPIO_BANK01 0x01E26010 +#define DAVINCI_GPIO_BANK23 0x01E26038 +#define DAVINCI_GPIO_BANK45 0x01E26060 +#define DAVINCI_GPIO_BANK67 0x01E26088 +#endif /* CONFIG_SOC_DA8XX */ + struct davinci_gpio { unsigned int dir; unsigned int out_data; @@ -49,4 +58,9 @@ struct davinci_gpio_bank { unsigned long base; }; +#define davinci_gpio_bank01 ((struct davinci_gpio *)DAVINCI_GPIO_BANK01) +#define davinci_gpio_bank23 ((struct davinci_gpio *)DAVINCI_GPIO_BANK23) +#define davinci_gpio_bank45 ((struct davinci_gpio *)DAVINCI_GPIO_BANK45) +#define davinci_gpio_bank67 ((struct davinci_gpio *)DAVINCI_GPIO_BANK67) + #endif diff --git a/include/asm-blackfin/mach-common/bits/usb.h b/include/asm-blackfin/mach-common/bits/usb.h new file mode 100644 index 0000000000..c6390589bc --- /dev/null +++ b/include/asm-blackfin/mach-common/bits/usb.h @@ -0,0 +1,264 @@ +/* + * USB Masks + */ + +#ifndef __BFIN_PERIPHERAL_USB__ +#define __BFIN_PERIPHERAL_USB__ + +/* Bit masks for USB_FADDR */ + +#define FUNCTION_ADDRESS 0x7f /* Function address */ + +/* Bit masks for USB_POWER */ + +#define ENABLE_SUSPENDM 0x1 /* enable SuspendM output */ +#define SUSPEND_MODE 0x2 /* Suspend Mode indicator */ +#define RESUME_MODE 0x4 /* DMA Mode */ +#define RESET 0x8 /* Reset indicator */ +#define HS_MODE 0x10 /* High Speed mode indicator */ +#define HS_ENABLE 0x20 /* high Speed Enable */ +#define SOFT_CONN 0x40 /* Soft connect */ +#define ISO_UPDATE 0x80 /* Isochronous update */ + +/* Bit masks for USB_INTRTX */ + +#define EP0_TX 0x1 /* Tx Endpoint 0 interrupt */ +#define EP1_TX 0x2 /* Tx Endpoint 1 interrupt */ +#define EP2_TX 0x4 /* Tx Endpoint 2 interrupt */ +#define EP3_TX 0x8 /* Tx Endpoint 3 interrupt */ +#define EP4_TX 0x10 /* Tx Endpoint 4 interrupt */ +#define EP5_TX 0x20 /* Tx Endpoint 5 interrupt */ +#define EP6_TX 0x40 /* Tx Endpoint 6 interrupt */ +#define EP7_TX 0x80 /* Tx Endpoint 7 interrupt */ + +/* Bit masks for USB_INTRRX */ + +#define EP1_RX 0x2 /* Rx Endpoint 1 interrupt */ +#define EP2_RX 0x4 /* Rx Endpoint 2 interrupt */ +#define EP3_RX 0x8 /* Rx Endpoint 3 interrupt */ +#define EP4_RX 0x10 /* Rx Endpoint 4 interrupt */ +#define EP5_RX 0x20 /* Rx Endpoint 5 interrupt */ +#define EP6_RX 0x40 /* Rx Endpoint 6 interrupt */ +#define EP7_RX 0x80 /* Rx Endpoint 7 interrupt */ + +/* Bit masks for USB_INTRTXE */ + +#define EP0_TX_E 0x1 /* Endpoint 0 interrupt Enable */ +#define EP1_TX_E 0x2 /* Tx Endpoint 1 interrupt enable */ +#define EP2_TX_E 0x4 /* Tx Endpoint 2 interrupt enable */ +#define EP3_TX_E 0x8 /* Tx Endpoint 3 interrupt enable */ +#define EP4_TX_E 0x10 /* Tx Endpoint 4 interrupt enable */ +#define EP5_TX_E 0x20 /* Tx Endpoint 5 interrupt enable */ +#define EP6_TX_E 0x40 /* Tx Endpoint 6 interrupt enable */ +#define EP7_TX_E 0x80 /* Tx Endpoint 7 interrupt enable */ + +/* Bit masks for USB_INTRRXE */ + +#define EP1_RX_E 0x02 /* Rx Endpoint 1 interrupt enable */ +#define EP2_RX_E 0x04 /* Rx Endpoint 2 interrupt enable */ +#define EP3_RX_E 0x08 /* Rx Endpoint 3 interrupt enable */ +#define EP4_RX_E 0x10 /* Rx Endpoint 4 interrupt enable */ +#define EP5_RX_E 0x20 /* Rx Endpoint 5 interrupt enable */ +#define EP6_RX_E 0x40 /* Rx Endpoint 6 interrupt enable */ +#define EP7_RX_E 0x80 /* Rx Endpoint 7 interrupt enable */ + +/* Bit masks for USB_INTRUSB */ + +#define SUSPEND_B 0x01 /* Suspend indicator */ +#define RESUME_B 0x02 /* Resume indicator */ +#define RESET_OR_BABLE_B 0x04 /* Reset/babble indicator */ +#define SOF_B 0x08 /* Start of frame */ +#define CONN_B 0x10 /* Connection indicator */ +#define DISCON_B 0x20 /* Disconnect indicator */ +#define SESSION_REQ_B 0x40 /* Session Request */ +#define VBUS_ERROR_B 0x80 /* Vbus threshold indicator */ + +/* Bit masks for USB_INTRUSBE */ + +#define SUSPEND_BE 0x01 /* Suspend indicator int enable */ +#define RESUME_BE 0x02 /* Resume indicator int enable */ +#define RESET_OR_BABLE_BE 0x04 /* Reset/babble indicator int enable */ +#define SOF_BE 0x08 /* Start of frame int enable */ +#define CONN_BE 0x10 /* Connection indicator int enable */ +#define DISCON_BE 0x20 /* Disconnect indicator int enable */ +#define SESSION_REQ_BE 0x40 /* Session Request int enable */ +#define VBUS_ERROR_BE 0x80 /* Vbus threshold indicator int enable */ + +/* Bit masks for USB_FRAME */ + +#define FRAME_NUMBER 0x7ff /* Frame number */ + +/* Bit masks for USB_INDEX */ + +#define SELECTED_ENDPOINT 0xf /* selected endpoint */ + +/* Bit masks for USB_GLOBAL_CTL */ + +#define GLOBAL_ENA 0x0001 /* enables USB module */ +#define EP1_TX_ENA 0x0002 /* Transmit endpoint 1 enable */ +#define EP2_TX_ENA 0x0004 /* Transmit endpoint 2 enable */ +#define EP3_TX_ENA 0x0008 /* Transmit endpoint 3 enable */ +#define EP4_TX_ENA 0x0010 /* Transmit endpoint 4 enable */ +#define EP5_TX_ENA 0x0020 /* Transmit endpoint 5 enable */ +#define EP6_TX_ENA 0x0040 /* Transmit endpoint 6 enable */ +#define EP7_TX_ENA 0x0080 /* Transmit endpoint 7 enable */ +#define EP1_RX_ENA 0x0100 /* Receive endpoint 1 enable */ +#define EP2_RX_ENA 0x0200 /* Receive endpoint 2 enable */ +#define EP3_RX_ENA 0x0400 /* Receive endpoint 3 enable */ +#define EP4_RX_ENA 0x0800 /* Receive endpoint 4 enable */ +#define EP5_RX_ENA 0x1000 /* Receive endpoint 5 enable */ +#define EP6_RX_ENA 0x2000 /* Receive endpoint 6 enable */ +#define EP7_RX_ENA 0x4000 /* Receive endpoint 7 enable */ + +/* Bit masks for USB_OTG_DEV_CTL */ + +#define SESSION 0x1 /* session indicator */ +#define HOST_REQ 0x2 /* Host negotiation request */ +#define HOST_MODE 0x4 /* indicates USBDRC is a host */ +#define VBUS0 0x8 /* Vbus level indicator[0] */ +#define VBUS1 0x10 /* Vbus level indicator[1] */ +#define LSDEV 0x20 /* Low-speed indicator */ +#define FSDEV 0x40 /* Full or High-speed indicator */ +#define B_DEVICE 0x80 /* A' or 'B' device indicator */ + +/* Bit masks for USB_OTG_VBUS_IRQ */ + +#define DRIVE_VBUS_ON 0x1 /* indicator to drive VBUS control circuit */ +#define DRIVE_VBUS_OFF 0x2 /* indicator to shut off charge pump */ +#define CHRG_VBUS_START 0x4 /* indicator for external circuit to start charging VBUS */ +#define CHRG_VBUS_END 0x8 /* indicator for external circuit to end charging VBUS */ +#define DISCHRG_VBUS_START 0x10 /* indicator to start discharging VBUS */ +#define DISCHRG_VBUS_END 0x20 /* indicator to stop discharging VBUS */ + +/* Bit masks for USB_OTG_VBUS_MASK */ + +#define DRIVE_VBUS_ON_ENA 0x01 /* enable DRIVE_VBUS_ON interrupt */ +#define DRIVE_VBUS_OFF_ENA 0x02 /* enable DRIVE_VBUS_OFF interrupt */ +#define CHRG_VBUS_START_ENA 0x04 /* enable CHRG_VBUS_START interrupt */ +#define CHRG_VBUS_END_ENA 0x08 /* enable CHRG_VBUS_END interrupt */ +#define DISCHRG_VBUS_START_ENA 0x10 /* enable DISCHRG_VBUS_START interrupt */ +#define DISCHRG_VBUS_END_ENA 0x20 /* enable DISCHRG_VBUS_END interrupt */ + +/* Bit masks for USB_CSR0 */ + +#define RXPKTRDY 0x1 /* data packet receive indicator */ +#define TXPKTRDY 0x2 /* data packet in FIFO indicator */ +#define STALL_SENT 0x4 /* STALL handshake sent */ +#define DATAEND 0x8 /* Data end indicator */ +#define SETUPEND 0x10 /* Setup end */ +#define SENDSTALL 0x20 /* Send STALL handshake */ +#define SERVICED_RXPKTRDY 0x40 /* used to clear the RxPktRdy bit */ +#define SERVICED_SETUPEND 0x80 /* used to clear the SetupEnd bit */ +#define FLUSHFIFO 0x100 /* flush endpoint FIFO */ +#define STALL_RECEIVED_H 0x4 /* STALL handshake received host mode */ +#define SETUPPKT_H 0x8 /* send Setup token host mode */ +#define ERROR_H 0x10 /* timeout error indicator host mode */ +#define REQPKT_H 0x20 /* Request an IN transaction host mode */ +#define STATUSPKT_H 0x40 /* Status stage transaction host mode */ +#define NAK_TIMEOUT_H 0x80 /* EP0 halted after a NAK host mode */ + +/* Bit masks for USB_COUNT0 */ + +#define EP0_RX_COUNT 0x7f /* number of received bytes in EP0 FIFO */ + +/* Bit masks for USB_NAKLIMIT0 */ + +#define EP0_NAK_LIMIT 0x1f /* frames/micro frames count after which EP0 timeouts */ + +/* Bit masks for USB_TX_MAX_PACKET */ + +#define MAX_PACKET_SIZE_T 0x7ff /* maximum data pay load in a frame */ + +/* Bit masks for USB_RX_MAX_PACKET */ + +#define MAX_PACKET_SIZE_R 0x7ff /* maximum data pay load in a frame */ + +/* Bit masks for USB_TXCSR */ + +#define TXPKTRDY_T 0x1 /* data packet in FIFO indicator */ +#define FIFO_NOT_EMPTY_T 0x2 /* FIFO not empty */ +#define UNDERRUN_T 0x4 /* TxPktRdy not set for an IN token */ +#define FLUSHFIFO_T 0x8 /* flush endpoint FIFO */ +#define STALL_SEND_T 0x10 /* issue a Stall handshake */ +#define STALL_SENT_T 0x20 /* Stall handshake transmitted */ +#define CLEAR_DATATOGGLE_T 0x40 /* clear endpoint data toggle */ +#define INCOMPTX_T 0x80 /* indicates that a large packet is split */ +#define DMAREQMODE_T 0x400 /* DMA mode (0 or 1) selection */ +#define FORCE_DATATOGGLE_T 0x800 /* Force data toggle */ +#define DMAREQ_ENA_T 0x1000 /* Enable DMA request for Tx EP */ +#define ISO_T 0x4000 /* enable Isochronous transfers */ +#define AUTOSET_T 0x8000 /* allows TxPktRdy to be set automatically */ +#define ERROR_TH 0x4 /* error condition host mode */ +#define STALL_RECEIVED_TH 0x20 /* Stall handshake received host mode */ +#define NAK_TIMEOUT_TH 0x80 /* NAK timeout host mode */ + +/* Bit masks for USB_TXCOUNT */ + +#define TX_COUNT 0x1fff /* Byte len for the selected endpoint Tx FIFO */ + +/* Bit masks for USB_RXCSR */ + +#define RXPKTRDY_R 0x1 /* data packet in FIFO indicator */ +#define FIFO_FULL_R 0x2 /* FIFO not empty */ +#define OVERRUN_R 0x4 /* TxPktRdy not set for an IN token */ +#define DATAERROR_R 0x8 /* Out packet cannot be loaded into Rx FIFO */ +#define FLUSHFIFO_R 0x10 /* flush endpoint FIFO */ +#define STALL_SEND_R 0x20 /* issue a Stall handshake */ +#define STALL_SENT_R 0x40 /* Stall handshake transmitted */ +#define CLEAR_DATATOGGLE_R 0x80 /* clear endpoint data toggle */ +#define INCOMPRX_R 0x100 /* indicates that a large packet is split */ +#define DMAREQMODE_R 0x800 /* DMA mode (0 or 1) selection */ +#define DISNYET_R 0x1000 /* disable Nyet handshakes */ +#define DMAREQ_ENA_R 0x2000 /* Enable DMA request for Tx EP */ +#define ISO_R 0x4000 /* enable Isochronous transfers */ +#define AUTOCLEAR_R 0x8000 /* allows TxPktRdy to be set automatically */ +#define ERROR_RH 0x4 /* TxPktRdy not set for an IN token host mode */ +#define REQPKT_RH 0x20 /* request an IN transaction host mode */ +#define STALL_RECEIVED_RH 0x40 /* Stall handshake received host mode */ +#define INCOMPRX_RH 0x100 /* large packet is split host mode */ +#define DMAREQMODE_RH 0x800 /* DMA mode (0 or 1) selection host mode */ +#define AUTOREQ_RH 0x4000 /* sets ReqPkt automatically host mode */ + +/* Bit masks for USB_RXCOUNT */ + +#define RX_COUNT 0x1fff /* Packet byte len in the Rx FIFO */ + +/* Bit masks for USB_TXTYPE */ + +#define TARGET_EP_NO_T 0xf /* EP number */ +#define PROTOCOL_T 0xc /* transfer type */ + +/* Bit masks for USB_TXINTERVAL */ + +#define TX_POLL_INTERVAL 0xff /* polling interval for selected Tx EP */ + +/* Bit masks for USB_RXTYPE */ + +#define TARGET_EP_NO_R 0xf /* EP number */ +#define PROTOCOL_R 0xc /* transfer type */ + +/* Bit masks for USB_RXINTERVAL */ + +#define RX_POLL_INTERVAL 0xff /* polling interval for selected Rx EP */ + +/* Bit masks for USB_DMA_INTERRUPT */ + +#define DMA0_INT 0x1 /* DMA0 pending interrupt */ +#define DMA1_INT 0x2 /* DMA1 pending interrupt */ +#define DMA2_INT 0x4 /* DMA2 pending interrupt */ +#define DMA3_INT 0x8 /* DMA3 pending interrupt */ +#define DMA4_INT 0x10 /* DMA4 pending interrupt */ +#define DMA5_INT 0x20 /* DMA5 pending interrupt */ +#define DMA6_INT 0x40 /* DMA6 pending interrupt */ +#define DMA7_INT 0x80 /* DMA7 pending interrupt */ + +/* Bit masks for USB_DMAxCONTROL */ + +#define DMA_ENA 0x1 /* DMA enable */ +#define DIRECTION 0x2 /* direction of DMA transfer */ +#define MODE 0x4 /* DMA Bus error */ +#define INT_ENA 0x8 /* Interrupt enable */ +#define EPNUM 0xf0 /* EP number */ +#define BUSERROR 0x100 /* DMA Bus error */ + +#endif diff --git a/include/configs/da830evm.h b/include/configs/da830evm.h index 38e2ce1f1c..432cd57a70 100644 --- a/include/configs/da830evm.h +++ b/include/configs/da830evm.h @@ -149,6 +149,11 @@ #define CONFIG_SYS_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED #endif +/* + * USB configuration + */ +#define CONFIG_USB_DA8XX /* Platform hookup to MUSB controller */ +#define CONFIG_MUSB_HCD /* * U-Boot general configuration @@ -234,10 +239,33 @@ #endif #ifdef CONFIG_USB_DA8XX -#define CONFIG_CMD_USB /* include support for usb */ -#define CONFIG_CMD_STORAGE /* include support for usb */ -#define CONFIG_CMD_FAT /* include support for FAT/storage*/ -#define CONFIG_DOS_PARTITION /* include support for FAT/storage*/ -#endif +#ifdef CONFIG_MUSB_HCD /* include support for usb host */ +#define CONFIG_CMD_USB /* include support for usb cmd */ + +#define CONFIG_USB_STORAGE /* MSC class support */ +#define CONFIG_CMD_STORAGE /* inclue support for usb-storage cmd */ +#define CONFIG_CMD_FAT /* inclue support for FAT/storage */ +#define CONFIG_DOS_PARTITION /* inclue support for FAT/storage */ + +#ifdef CONFIG_USB_KEYBOARD /* HID class support */ +#define CONFIG_SYS_USB_EVENT_POLL +#define CONFIG_PREBOOT "usb start" +#endif /* CONFIG_USB_KEYBOARD */ + +#endif /* CONFIG_MUSB_HCD */ + +#ifdef CONFIG_MUSB_UDC +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "DA830EVM" +#endif /* CONFIG_MUSB_UDC */ + +#endif /* CONFIG_USB_DA8XX */ #endif /* __CONFIG_H */ diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 5788d581af..568d9fc0cd 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -282,8 +282,20 @@ /* USB */ #ifdef CONFIG_440EPX + +#undef CONFIG_USB_EHCI /* OHCI by default */ + +#ifdef CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_PPC4XX +#define CONFIG_SYS_PPC4XX_USB_ADDR 0xe0000300 +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_EHCI_MMIO_BIG_ENDIAN +#define CONFIG_EHCI_DESC_BIG_ENDIAN +#ifdef CONFIG_4xx_DCACHE +#define CONFIG_EHCI_DCACHE +#endif +#else /* CONFIG_USB_EHCI */ #define CONFIG_USB_OHCI_NEW -#define CONFIG_USB_STORAGE #define CONFIG_SYS_OHCI_BE_CONTROLLER #undef CONFIG_SYS_USB_OHCI_BOARD_INIT @@ -291,7 +303,9 @@ #define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 +#endif +#define CONFIG_USB_STORAGE /* Comment this out to enable USB 1.1 device */ #define USB_2_0_DEVICE diff --git a/include/usb.h b/include/usb.h index 1cc3e4229d..a1f09d4d7a 100644 --- a/include/usb.h +++ b/include/usb.h @@ -132,7 +132,8 @@ struct usb_device { defined(CONFIG_USB_EHCI) || defined(CONFIG_USB_OHCI_NEW) || \ defined(CONFIG_USB_SL811HS) || defined(CONFIG_USB_ISP116X_HCD) || \ defined(CONFIG_USB_R8A66597_HCD) || defined(CONFIG_USB_DAVINCI) || \ - defined(CONFIG_USB_OMAP3) + defined(CONFIG_USB_OMAP3) || defined(CONFIG_USB_DA8XX) || \ + defined(CONFIG_USB_BLACKFIN) int usb_lowlevel_init(void); int usb_lowlevel_stop(void); |