diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/clearfog.h | 176 | ||||
| -rw-r--r-- | include/configs/db-88f6820-gp.h | 25 | ||||
| -rw-r--r-- | include/configs/db-mv784mp-gp.h | 60 | ||||
| -rw-r--r-- | include/configs/ds414.h | 162 | ||||
| -rw-r--r-- | include/configs/maxbcm.h | 15 |
5 files changed, 369 insertions, 69 deletions
diff --git a/include/configs/clearfog.h b/include/configs/clearfog.h new file mode 100644 index 0000000000..f0de827fd2 --- /dev/null +++ b/include/configs/clearfog.h @@ -0,0 +1,176 @@ +/* + * Copyright (C) 2015 Stefan Roese <sr@denx.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_CLEARFOG_H +#define _CONFIG_CLEARFOG_H + +/* + * High Level Configuration Options (easy to change) + */ + +#define CONFIG_DISPLAY_BOARDINFO_LATE + +/* + * TEXT_BASE needs to be below 16MiB, since this area is scrubbed + * for DDR ECC byte filling in the SPL before loading the main + * U-Boot into it. + */ +#define CONFIG_SYS_TEXT_BASE 0x00800000 +#define CONFIG_SYS_TCLK 250000000 /* 250MHz */ + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#define CONFIG_CMD_BOOTZ +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ENV +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_FS_GENERIC +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MMC +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_SF +#define CONFIG_CMD_SPI +#define CONFIG_CMD_TFTPPUT +#define CONFIG_CMD_TIME + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MVTWSI +#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE +#define CONFIG_SYS_I2C_SLAVE 0x0 +#define CONFIG_SYS_I2C_SPEED 100000 + +/* SPI NOR flash default params, used by sf commands */ +#define CONFIG_SF_DEFAULT_SPEED 1000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 +#define CONFIG_SPI_FLASH_STMICRO + +/* + * SDIO/MMC Card Configuration + */ +#define CONFIG_MMC +#define CONFIG_MMC_SDMA +#define CONFIG_GENERIC_MMC +#define CONFIG_SDHCI +#define CONFIG_MV_SDHCI +#define CONFIG_SYS_MMC_BASE MVEBU_SDIO_BASE + +/* Partition support */ +#define CONFIG_DOS_PARTITION +#define CONFIG_EFI_PARTITION + +/* Additional FS support/configuration */ +#define CONFIG_SUPPORT_VFAT + +/* USB/EHCI configuration */ +#define CONFIG_EHCI_IS_TDI + +#define CONFIG_ENV_MIN_ENTRIES 128 + +/* Environment in MMC */ +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_SECT_SIZE 0x200 +#define CONFIG_ENV_SIZE 0x10000 +/* + * For SD - reserve 1 LBA for MBR + 1M for u-boot image. The MMC/eMMC + * boot image starts @ LBA-0. + * As result in MMC/eMMC case it will be a 1 sector gap between u-boot + * image and environment + */ +#define CONFIG_ENV_OFFSET 0xf0000 +#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET + +#define CONFIG_PHY_MARVELL /* there is a marvell phy */ +#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ + +/* PCIe support */ +#ifndef CONFIG_SPL_BUILD +#define CONFIG_PCI +#define CONFIG_PCI_MVEBU +#define CONFIG_PCI_PNP +#define CONFIG_PCI_SCAN_SHOW +#endif + +#define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ +#define CONFIG_SYS_ALT_MEMTEST + +/* Keep device tree and initrd in lower memory so the kernel can access them */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "fdt_high=0x10000000\0" \ + "initrd_high=0x10000000\0" + +/* SPL */ +/* + * Select the boot device here + * + * Currently supported are: + * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash + * SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1) + */ +#define SPL_BOOT_SPI_NOR_FLASH 1 +#define SPL_BOOT_SDIO_MMC_CARD 2 +#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SDIO_MMC_CARD + +/* Defines for SPL */ +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_SIZE (140 << 10) +#define CONFIG_SPL_TEXT_BASE 0x40000030 +#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030) + +#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) +#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MALLOC_SIMPLE +#endif + +#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) +#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT + +#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH +/* SPL related SPI defines */ +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SPL_SPI_CS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 +#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS +#endif + +#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD +/* SPL related MMC defines */ +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10) +#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR ((CONFIG_SYS_U_BOOT_OFFS / 512)\ + + 1) +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS ((512 << 10) / 512) /* 512KiB */ +#ifdef CONFIG_SPL_BUILD +#define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */ +#endif +#endif + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +#endif /* _CONFIG_CLEARFOG_H */ diff --git a/include/configs/db-88f6820-gp.h b/include/configs/db-88f6820-gp.h index 3673e5e368..ef14132b89 100644 --- a/include/configs/db-88f6820-gp.h +++ b/include/configs/db-88f6820-gp.h @@ -10,15 +10,7 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_ARMADA_XP /* SOC Family Name */ -#define CONFIG_ARMADA_38X -#define CONFIG_DB_88F6820_GP /* Board target name for DDR training */ -#define CONFIG_SYS_L2_PL310 - -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#endif #define CONFIG_DISPLAY_BOARDINFO_LATE /* @@ -99,16 +91,15 @@ #define CONFIG_ENV_SECT_SIZE (256 << 10) /* 256KiB sectors */ #define CONFIG_PHY_MARVELL /* there is a marvell phy */ -#define CONFIG_PHY_ADDR { 1, 0 } -#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ /* PCIe support */ +#ifndef CONFIG_SPL_BUILD #define CONFIG_PCI #define CONFIG_PCI_MVEBU #define CONFIG_PCI_PNP #define CONFIG_PCI_SCAN_SHOW -#define CONFIG_E1000 /* enable Intel E1000 support for testing */ +#endif #define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ #define CONFIG_SYS_ALT_MEMTEST @@ -139,9 +130,9 @@ #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE) #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) -#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ - CONFIG_SPL_BSS_MAX_SIZE) -#define CONFIG_SYS_SPL_MALLOC_SIZE (16 << 10) +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MALLOC_SIMPLE +#endif #define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) @@ -158,7 +149,7 @@ #define CONFIG_SPL_SPI_LOAD #define CONFIG_SPL_SPI_BUS 0 #define CONFIG_SPL_SPI_CS 0 -#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000 #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS #endif @@ -176,10 +167,6 @@ #endif #endif -/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */ -#define CONFIG_SYS_MVEBU_DDR_A38X -#define CONFIG_DDR3 - /* * mv-common.h should be defined after CMD configs since it used them * to enable certain macros diff --git a/include/configs/db-mv784mp-gp.h b/include/configs/db-mv784mp-gp.h index ab6e5a5bce..c8b0344185 100644 --- a/include/configs/db-mv784mp-gp.h +++ b/include/configs/db-mv784mp-gp.h @@ -1,5 +1,5 @@ /* - * Copyright (C) 2014 Stefan Roese <sr@denx.de> + * Copyright (C) 2014-2015 Stefan Roese <sr@denx.de> * * SPDX-License-Identifier: GPL-2.0+ */ @@ -10,12 +10,8 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_ARMADA_XP /* SOC Family Name */ #define CONFIG_DB_784MP_GP /* Board target name for DDR training */ -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#endif #define CONFIG_DISPLAY_BOARDINFO_LATE /* @@ -30,13 +26,18 @@ * Commands configuration */ #define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#define CONFIG_CMD_CACHE #define CONFIG_CMD_DHCP #define CONFIG_CMD_ENV +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_EXT4 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_FS_GENERIC #define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_PING +#define CONFIG_CMD_SATA #define CONFIG_CMD_SF #define CONFIG_CMD_SPI #define CONFIG_CMD_TFTPPUT @@ -64,48 +65,29 @@ #define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */ #define CONFIG_PHY_MARVELL /* there is a marvell phy */ -#define CONFIG_PHY_ADDR { 0x10, 0x11, 0x12, 0x13 } -#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_QSGMII #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ -#define CONFIG_RESET_PHY_R #define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ #define CONFIG_SYS_ALT_MEMTEST /* SATA support */ -#ifdef CONFIG_CMD_IDE -#define __io -#define CONFIG_IDE_PREINIT -#define CONFIG_MVSATA_IDE - -/* Needs byte-swapping for ATA data register */ -#define CONFIG_IDE_SWAP_IO - -#define CONFIG_SYS_ATA_REG_OFFSET 0x0100 /* Offset for register access */ -#define CONFIG_SYS_ATA_DATA_OFFSET 0x0100 /* Offset for data I/O */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 - -/* Each 8-bit ATA register is aligned to a 4-bytes address */ -#define CONFIG_SYS_ATA_STRIDE 4 - -/* CONFIG_CMD_IDE requires some #defines for ATA registers */ -#define CONFIG_SYS_IDE_MAXBUS 2 -#define CONFIG_SYS_IDE_MAXDEVICE CONFIG_SYS_IDE_MAXBUS - -/* ATA registers base is at SATA controller base */ -#define CONFIG_SYS_ATA_BASE_ADDR MVEBU_AXP_SATA_BASE -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x2000 -#define CONFIG_SYS_ATA_IDE1_OFFSET 0x4000 - +#define CONFIG_SYS_SATA_MAX_DEVICE 2 +#define CONFIG_SATA_MV +#define CONFIG_LIBATA +#define CONFIG_LBA48 +#define CONFIG_EFI_PARTITION #define CONFIG_DOS_PARTITION -#endif /* CONFIG_CMD_IDE */ + +/* Additional FS support/configuration */ +#define CONFIG_SUPPORT_VFAT /* PCIe support */ +#ifndef CONFIG_SPL_BUILD #define CONFIG_PCI #define CONFIG_PCI_MVEBU #define CONFIG_PCI_PNP #define CONFIG_PCI_SCAN_SHOW -#define CONFIG_E1000 /* enable Intel E1000 support for testing */ +#endif /* NAND */ #define CONFIG_SYS_NAND_USE_FLASH_BBT @@ -139,9 +121,9 @@ #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10)) #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) -#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ - CONFIG_SPL_BSS_MAX_SIZE) -#define CONFIG_SYS_SPL_MALLOC_SIZE (16 << 10) +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MALLOC_SIMPLE +#endif #define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) @@ -161,7 +143,7 @@ #define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS /* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */ -#define CONFIG_SYS_MVEBU_DDR_AXP #define CONFIG_SPD_EEPROM 0x4e +#define CONFIG_BOARD_ECC_SUPPORT /* this board supports ECC */ #endif /* _CONFIG_DB_MV7846MP_GP_H */ diff --git a/include/configs/ds414.h b/include/configs/ds414.h new file mode 100644 index 0000000000..e3c7087a1f --- /dev/null +++ b/include/configs/ds414.h @@ -0,0 +1,162 @@ +/* + * Copyright (C) 2014 Stefan Roese <sr@denx.de> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef _CONFIG_SYNOLOGY_DS414_H +#define _CONFIG_SYNOLOGY_DS414_H + +/* + * High Level Configuration Options (easy to change) + */ +#define CONFIG_DISPLAY_BOARDINFO_LATE + +/* + * TEXT_BASE needs to be below 16MiB, since this area is scrubbed + * for DDR ECC byte filling in the SPL before loading the main + * U-Boot into it. + */ +#define CONFIG_SYS_TEXT_BASE 0x00800000 +#define CONFIG_SYS_TCLK 250000000 /* 250MHz */ + +/* + * Commands configuration + */ +#define CONFIG_SYS_NO_FLASH /* Declare no flash (NOR/SPI) */ +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ENV +#define CONFIG_CMD_I2C +#define CONFIG_CMD_PING +#define CONFIG_CMD_SF +#define CONFIG_CMD_SPI +#define CONFIG_CMD_TFTPPUT +#define CONFIG_CMD_TIME +#define CONFIG_CMD_USB + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MVTWSI +#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE +#define CONFIG_SYS_I2C_SLAVE 0x0 +#define CONFIG_SYS_I2C_SPEED 100000 + +/* SPI NOR flash default params, used by sf commands */ +#define CONFIG_SF_DEFAULT_SPEED 1000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_3 + +/* Environment in SPI NOR flash */ +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_OFFSET 0x7E0000 /* RedBoot config partition in DTS */ +#define CONFIG_ENV_SIZE (64 << 10) /* 64KiB */ +#define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */ + +#define CONFIG_PHY_MARVELL /* there is a marvell phy */ +#define CONFIG_PHY_ADDR { 0x1, 0x0 } +#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII + +#define CONFIG_SYS_ALT_MEMTEST + +/* PCIe support */ +#ifndef CONFIG_SPL_BUILD +#define CONFIG_PCI +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PCI_ENUM +#define CONFIG_PCI_MVEBU +#define CONFIG_PCI_SCAN_SHOW +#endif + +/* USB/EHCI/XHCI configuration */ + +#define CONFIG_DM_USB +#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 + +/* FIXME: broken XHCI support + * Below defines should enable support for the two rear USB3 ports. Sadly, this + * does not work because: + * - xhci-pci seems to not support DM_USB, so with that enabled it is not + * found. + * - USB init fails, controller does not respond in time */ +#if 0 +#undef CONFIG_DM_USB +#define CONFIG_USB_XHCI +#define CONFIG_USB_XHCI_PCI +#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 +#endif + +#if !defined(CONFIG_USB_XHCI) +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_MARVELL +#define CONFIG_EHCI_IS_TDI +#endif + +/* why is this only defined in mv-common.h if CONFIG_DM is undefined? */ +#define CONFIG_USB_STORAGE +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION +#define CONFIG_SUPPORT_VFAT +#define CONFIG_SYS_MVFS + +/* + * mv-common.h should be defined after CMD configs since it used them + * to enable certain macros + */ +#include "mv-common.h" + +/* + * Memory layout while starting into the bin_hdr via the + * BootROM: + * + * 0x4000.4000 - 0x4003.4000 headers space (192KiB) + * 0x4000.4030 bin_hdr start address + * 0x4003.4000 - 0x4004.7c00 BootROM memory allocations (15KiB) + * 0x4007.fffc BootROM stack top + * + * The address space between 0x4007.fffc and 0x400f.fff is not locked in + * L2 cache thus cannot be used. + */ + +/* SPL */ +/* Defines for SPL */ +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_TEXT_BASE 0x40004030 +#define CONFIG_SPL_MAX_SIZE ((128 << 10) - 0x4030) + +#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10)) +#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MALLOC_SIMPLE +#endif + +#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) +#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT + +/* SPL related SPI defines */ +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SPL_SPI_CS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000 + +/* DS414 bus width is 32bits */ +#define CONFIG_DDR_32BIT + +/* Use random ethernet address if not configured */ +#define CONFIG_LIB_RAND +#define CONFIG_NET_RANDOM_ETHADDR + +/* Default Environment */ +#define CONFIG_BOOTCOMMAND "sf read ${loadaddr} 0xd0000 0x700000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200" +#define CONFIG_LOADADDR 0x80000 +#undef CONFIG_PREBOOT /* override preboot for USB and SPI flash init */ +#define CONFIG_PREBOOT "usb start; sf probe" + +#endif /* _CONFIG_SYNOLOGY_DS414_H */ diff --git a/include/configs/maxbcm.h b/include/configs/maxbcm.h index da49243ebf..43d7fd03a3 100644 --- a/include/configs/maxbcm.h +++ b/include/configs/maxbcm.h @@ -10,10 +10,6 @@ /* * High Level Configuration Options (easy to change) */ -#define CONFIG_ARMADA_XP /* SOC Family Name */ -#ifdef CONFIG_SPL_BUILD -#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ -#endif #define CONFIG_DISPLAY_BOARDINFO_LATE /* @@ -55,10 +51,7 @@ #define CONFIG_ENV_SECT_SIZE (64 << 10) /* 64KiB sectors */ #define CONFIG_PHY_MARVELL /* there is a marvell phy */ -#define CONFIG_PHY_ADDR { 0x0, 0x1, 0x2, 0x3 } -#define CONFIG_SYS_NETA_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII #define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */ -#define CONFIG_RESET_PHY_R #define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup */ #define CONFIG_SYS_ALT_MEMTEST @@ -91,9 +84,9 @@ #define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10)) #define CONFIG_SPL_BSS_MAX_SIZE (16 << 10) -#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ - CONFIG_SPL_BSS_MAX_SIZE) -#define CONFIG_SYS_SPL_MALLOC_SIZE (16 << 10) +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MALLOC_SIMPLE +#endif #define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10)) #define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4) @@ -112,7 +105,7 @@ #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 /* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */ -#define CONFIG_SYS_MVEBU_DDR_AXP #define CONFIG_DDR_FIXED_SIZE (1 << 20) /* 1GiB */ +#define CONFIG_BOARD_ECC_SUPPORT /* this board supports ECC */ #endif /* _CONFIG_DB_MV7846MP_GP_H */ |