summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-05-19MX31: Added support for the Casio COM57H5M10XRC to QONGStefano Babic
The patch adds setup to connect a CASIO COM57H5M10XRC (640x480 TFT display) to the QONG module. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05Add SPI support to mx51evk boardStefano Babic
The patch adds SPI devices to the mx51evk board. The MC13892 chip (PMIC) is supported. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05MX: Added definition file for MC13892Stefano Babic
The MC13892 is a Power Controller used with processors of the family MX.51. The file adds definitions to be used to setup the internal registers via SPI. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05SPI: added support for MX51 to mxc_spiStefano Babic
This patch add SPI support for the MX51 processor. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05MX31: Add support for PMIC to the QONG moduleStefano Babic
Add support for the PMIC (MC13783) controller and enables charging of the RTC battery. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05MX: RTC13783 uses general function to access PMICStefano Babic
The RTC is part of the Freescale's PMIC controller. Use general function to access to PMIC internal registers. Signed-off-by: Stefano Babic <sbabic@denx.de> Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-05-05MX: Added Freescale Power Management DriverStefano Babic
The patch add supports for the Freescale's Power Management Controller (known as Atlas) used together with i.MX31/51 processors. It was tested with a MC13783 (MX31) and MC13892 (MX51). Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05i.MX31: Activate NAND support for i.MX31 Litekit board.Magnus Lilja
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-05-05MX51: Fix MX51 CPU detect messageFabio Estevam
Fix MX51 CPU detect message. Original string was: CPU: Freescale i.MX51 family 3.0V at 800 MHz which can be misinterpreted as 3.0 Volts instead of the silicon revision. ,change it to: CPU: Freescale i.MX51 family rev3.0 at 800 MHz Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2010-05-05MX51evk: Removed warningsStefano Babic
Changes reflect modifications in the fsl_esdhc driver (the clk_enable field war removed in the configuration structure). Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05tx25: fix crash while booting LinuxAnatolij Gustschin
Currently booting Linux on TX25 board doesn't work since there is no correct mach-id and boot parameters setup for tx25 board. Fix it now. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: John Rigby <jcrigby@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
2010-05-04configs: remove unused CONFIG_COMMAND_HISTORYKim Phillips
$ git grep CONFIG_COMMAND_HISTORY CHANGELOG: CONFIG_COMMAND_HISTORY include/configs/AP1000.h:#define CONFIG_COMMAND_HISTORY 1 include/configs/keymile-common.h:#define CONFIG_COMMAND_HISTORY 1 include/configs/manroland/common.h:#define CONFIG_COMMAND_HISTORY 1 $ Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Heiko Schocher <hs@denx.de>
2010-05-04mvsmr: fix link errorAnatolij Gustschin
MVSMR board support doesn't link since recent rework of U-Boot directory structure. Fix it now. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Fixed merge conflict Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-05-04Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk
2010-05-04Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
2010-05-03Blackfin: bfin_mac: hook up new write_hwaddr functionMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: ethoc: add write_hwaddr supportThomas Chou
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: altera_tse: add write_hwaddr supportThomas Chou
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: fec_mxc: add write_hwaddr supportHeiko Schocher
tested on the magnesium board. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net:kirkwood_egiga.c: MAC addresses programming using write_hwaddrPrafulla Wadaskar
Added a new function kwgbe_write_hwaddr for programming egiga controller's hardware address. This function will be called for each egiga port being used Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03Program net device MAC addresses after initializingBen Warren
Add a new function to the eth_device struct for programming a network controller's hardware address. After all network devices have been initialized and the proper MAC address for each has been determined, make a device driver call to program the address into the device. Only device instances with valid unicast addresses will be programmed. Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Acked-by: Detlev Zundel <dzu@denx.de> Tested-by: Prafulla Wadaskar <prafulla@marvell.com> Tested-by: Heiko Schocher <hs@denx.de> Tested-by: Thomas Chou <thomas@wytron.com.tw>
2010-05-03net: add altera triple speeds ethernet mac driverThomas Chou
This driver supports the Altera triple speeds 10/100/1000 ethernet mac. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: add opencore 10/100 ethernet mac driverThomas Chou
This patch ports the opencore 10/100 ethernet mac driver ethoc.c from linux kernel to u-boot. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03smc911x driver frame alignment patchValentin Yakovenkov
SMSC911x chips have alignment function to allow frame payload data (which comes after 14-bytes ethernet header) to be aligned at some boundary when reading it from fifo (usually - 4 bytes boundary). This is done by inserting fake zeros bytes BEFORE actual frame data when reading from SMSC's fifo. This function controlled by RX_CFG register. There are bits that represents amount of fake bytes to be inserted. Linux uses alignment of 4 bytes. Ethernet frame header is 14 bytes long, so we need to add 2 fake bytes to get payload data aligned at 4-bytes boundary. Linux driver does this by adding IP_ALIGNMENT constant (defined at skb.h) when calculating fifo data length. All network subsystem of Linux uses this constant too when calculating different offsets. But u-boot does not use any packet data alignment, so we don't need to add anything when calculating fifo data length. Moreover, driver zeros the RX_CFG register just one line up, so chip does not insert any fake data at the beginig. So calculated data length is always bigger by 1 word. It seems that at almost every packet read we get an underflow condition at fifo and possible corruption of data. Especially at continuous transfers, such as tftp. Just after removing this magic addition, I've got tftp transfer speed as it aught to be at 100Mbps. It was really slow before. It seems that fifo underflow occurs only when using byte packing on 32-bit blackfin bus (may be because of very small delay between reads). Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: Kirkwood_egiga.c bugfixes for rx pathPrafulla Wadaskar
Cosmetic changes: Few comments updated Functionality: Rx packet frame size is programming should be done when port is in disabled state. this is corrected Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03fec_mxc.c: Fix MX27 FEC MAC validity checkEric Jarrige
Fix MX27 FEC logic to check validity of the MAC address in fuse. Only null (empty fuse) or invalid MAC address was retrieved from mx27 fuses before this change. Signed-off-by: Eric Jarrige <jorasse@armadeus.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03tsec: Wait for both RX and TX to stopAndy Fleming
When gracefully stopping the controller, the driver was continuing if *either* RX or TX had stopped. We need to wait for both, or the controller could get into an invalid state. Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: dm9000x: use standard I/O accessorsMike Frysinger
The current dm9000x driver accesses its memory mapped registers directly instead of using the standard I/O accessors. This can cause problems on Blackfin systems as the accesses can get out of order. So convert the direct volatile dereferences to use the normal in/out macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03mpc512x_fec: Move PHY initialization from probe into init routine.Detlev Zundel
This saves the autonegotation delay when not using ethernet in U-Boot Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03fec_mxc don't use internal eeprom on MX25John Rigby
Avoid using the internal eeprom on MX25 like MX51 already does. Signed-off-by: John Rigby <jcrigby@gmail.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03fix lockup in mcfmii/mii_discover_phy() in case communication failsWolfgang Wegner
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-0383xx: UEC: Added support for bitBang MII driver access to PHYsRichard Retanubun
This patch enabled support for having PHYs on bitBang MII and uec MII operating at the same time. Modeled after the MPC8360ADS implementation. Added the ability to specify which ethernet interfaces have bitbang SMI on the board header file. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03./net/net.c - make Microsoft dns servers happy with random_port() numbersRobin Getz
For some reason, (which I can't find any documentation on), if U-Boot gives a port number higher than 17500 to a Microsoft DNS server, the server will reply to port 17500, and U-Boot will ignore things (since that isn't the port it asked the DNS server to reply to). This fixes that by ensuring the random port number is less than 17500. Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03Remove unused "local_crc32" function.Detlev Zundel
For code archeologists, this is a nice example of copy and paste history. Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: Trivial coding style issue with empty for statementDetlev Zundel
Signed-off-by: Detlev Zundel <dzu@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03net: Kirkwood_egiga.c: fixed build warningsPrafulla Wadaskar
This patch fixes following build warnings for kirkwood_egiga.c kirkwood_egiga.c: In function "kwgbe_init": kirkwood_egiga.c:448: warning: dereferencing type-punned pointer will break strict-aliasing rules kirkwood_egiga.c: In function "kwgbe_recv": kirkwood_egiga.c:609: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-01Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/masterWolfgang Denk
2010-05-01Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk
2010-04-30pm9263 converted to at91 soc accessAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-04-30at91: define matrix registers bit fieldsAsen Dimov
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-04-30MX31: Removed erroneous board name from QONGStefano Babic
QONG is a module that can be installed on several boards, not only on the QONG-EVB manufactured by Dave srl. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30MX31: Add UBI support to QONG moduleStefano Babic
The UBI/UBIFS support is added to the QONG module. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30MX31: Support 128MB RAM on QONG moduleStefano Babic
The QONG module can be downsized and delivered with 128MB instead of 256MB. The patch adds run time support for the two different memory configurations. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30MX31: Add support for NAND to QONG boardStefano Babic
The NAND device is connected to the FPGA of the QONG board and not to the NFC controller. For this reason, the FPGA must be set and initialized before accessing to the NAND itself. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30MX31: add pin definitions for NAND controllerStefano Babic
Add pin definitions ralted to the NAND controller to be used to set up the pin multiplexer. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30MX31: add accessor function to get a gpioStefano Babic
The patch adds an accessor function to get the value of a gpio. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30mx51evk: correct list of possible BOOT_FROM valuesStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30mkimage: correct spelling error in imximageStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30MX25 print arm clock instead of mpllclk on bootJohn Rigby
Replace call to imx_get_mpllclk with imx_get_armclk to show frequency of ARM core instead of mpll internal bus in print_cpuinfo. Signed-off-by: John Rigby <jcrigby@gmail.com> CC: Stefano Babic <sbabic@denx.de>
2010-04-30configs/openrd_base.h: reordered macrosFrans Meulenbroeks
moved CONFIG_CMD_FAT to filesystem section swapped CONFIG_CMD_NAND and CONFIG_CMD_MII so they are alpha correct Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
generated by cgit (git 2.34.1) at 2025-01-13 20:24:33 +0000