summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-06-08ARM: dts: imx: m53menlo: Convert to DM_ETHMarek Vasut
Convert the board to DM_ETH instead of legacy networking. This requires a minor addition to the DT to satisfy the requirement for specifying a PHY node. No functional change from board user perspective. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2020-06-08ARM: imx: m53menlo: Do not fail boot on invalid splash screenMarek Vasut
None of these splash screen loading errors are so critical as to justify complete failure to boot, so just print error message as needed and return 0, the boot can very likely continue without the splash. Fix a couple of missing free(dst) instances as well. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2020-06-08ARM: imx: ddr: Add missing PHY resetMarek Vasut
The iMX7D RM 9.2.4.9.3 Power removal flow Table 9-11. Re-enabling power explicitly says both the DDR controller and the PHY must be reset in the correct sequence. Currently the code only resets the controller. This leads to a misbehavior where the system brings the DRAM up after reboot, but the DRAM is unstable. Add the missing reset. The easiest way to trigger this is by triggering WDT without having the WDT assert WDOG_B signal, i.e. mw.w 0x30280000 0x25 . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
2020-06-08power: pmic: Add SPL Kconfig entry for PFUZE100Marek Vasut
Add Kconfig entry for the PFUZE PMIC, SPL variant. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-06-08imx: imx8mp_evk: fix boot issuePeng Fan
The u-boot-spl.bin pad with ddr firmware conflicts with the CONFIG_MALLOC_F_ADDR area, the ddr firmware will be overwritten by malloc in SPL stage and cause ddr initialization not able to finish. So update the related addresses to fix the issue. Reported-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx8mp_evk: spl: no need the code since spl framework could do thatPeng Fan
We no need invoke the code, since spl framework could help us do that. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx8mp_evk: spl: use spl_early_initPeng Fan
Use spl_early_init to replace spl_init, spl_init will be invoked in board_init_r, we only need use spl_early_init to setup malloc and scan early dt. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx8mp_evk: spl: drop timer_initPeng Fan
timer_init has been invoked in arch_cpu_init, no need to invoke it again in board code. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx8mp_evk: spl: drop useless codePeng Fan
Drop useless getting ccm device, there is no need to explicted do this in board code, and we not enable SPL CLK currently. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx: Update MTD partitions layout for display5 (i.MX6Q) boardLukasz Majewski
This change updates the MTD partition layout on SPI-NOR memory for display5 board. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2020-06-08imx: rom api: fix image offset computationSébastien Szymanski
When not booting from FlexSPI, the offset computation is: offset = image_offset + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000; When booting from SD card or eMMC user partition, image_offset is 0x8000. It is useless to add and remove 0x8000. When booting from other device, image_offset is 0 so this computation is wrong. Simplfy this computation to work on all booting devices. Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2020-06-08verdin-imx8mm: Select the watchdog driverFabio Estevam
Currently watchdog driver is not selected, which causes system to reboot after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Signed-off-by: Fabio Estevam <festevam@gmail.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-06-08imx8mp_evk: Select the watchdog driverFabio Estevam
Currently watchdog driver is not selected, which causes system to reboot after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx8mm_beacon: Select the watchdog driverFabio Estevam
Currently watchdog driver is not selected, which causes system to reboot after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Adam Ford <aford173@gmail.com>
2020-06-08imx8mn_ddr4_evk: Select the watchdog driverFabio Estevam
Currently watchdog driver is not selected, which causes system to reboot after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx8mm_evk: Select the watchdog driverFabio Estevam
Currently the watchdog driver is not selected, which causes the following warnings in both SPL and U-Boot proper: U-Boot SPL 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300) Normal Boot WDT: Started without servicing (60s timeout) Trying to boot from MMC1 U-Boot 2020.07-rc1-00387-g67887903af (May 07 2020 - 23:49:27 -0300) CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz Reset cause: POR Model: FSL i.MX8MM EVK board DRAM: 2 GiB WDT: Started without servicing (60s timeout) .... System reboots after staying 60s in the U-Boot prompt. Fix this problem by enabling CONFIG_WATCHDOG so that watchdog can be properly serviced. Suggested-by: Marek Vasut <marex@denx.de> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx8mp_evk: Add a README fileFabio Estevam
Add a README file explaining the U-Boot build and SD card flash procedures. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2020-06-08imx: move ATF to the back of the FIT to fix loading over yModemPatrick Wildt
With yModem the FIT Image is only supplied once, so we can only seek forward in the yModem supplied image and never backwards. With the recent changes to the SPL mechanism, including loading U-Boot first, FDT after, then the loadables, we must also reorder the FIT image script to make sure that the loadables are last in the FIT image. Signed-off-by: Patrick Wildt <patrick@blueri.se> Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2020-06-08imx: Kconfig: enable IMX_BOOTAUX for i.MX8MPeng Fan
i.MX8M could use imx bootaux to boot m4/m7 core, so let's add it to the dependency list. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-06-08ARM: dts: imxrt1050: indent lcdif node correctlyGiulio Benetti
Accidentally submitted a patch with indentation not correct, let's fix it by indenting wrong lines. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Acked-by: Peng Fan <peng.fan@nxp.com>
2020-06-07rockchip: enable PCIe and NVMe on Pinebook ProPatrick Wildt
Enable CONFIG_PCI and CONFIG_NVME and related configs for the Pinebook Pro. Signed-off-by: Patrick Wildt <patrick@blueri.se> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: enable new usb config optionsHeiko Stuebner
With recently added changes we get support for usb3 including handling of the phys (type-c and inno-usb2), so enable the necessary config options on puma. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: drop special handling of usb host regulatorHeiko Stuebner
With the current usb stack in u-boot, all host ports on puma work flawlessly without any additional special handling, so drop that usb hub hacking from the puma board. Tested with mass-storage and usb-ethernet on both usb3 and usb2 ports. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2020-06-07rockchip: puma: remove separate fit generatorHeiko Stuebner
The introduction of the puma-specific generator was mainly a way to split the pmu firmware from the ATF binary and not having to distribute that 4GB (sparse) image that was created before moving to the bl31.elf as base. Looking at the publically available repository for that separate pmu firmware https://git.theobroma-systems.com/rk3399-cortex-m0.git/ there is also no activity for 3 years and apart from some build customizations no other changes were done. And even then, if changes need to be made, this can very well also happen in the atf context itself, so there is no real need to diverge from the established build procedure and we can just go back to using the main make_fit_atf.py script. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: reorganize devicetrees to actually work and match upstreamHeiko Stuebner
So far the puma dts files only just included the main puma dtsi without handling the actual baseboard and rk3399-puma.dtsi was very much detached from the variant in the mainline Linux kernel. Recent changes resulted in a strange situation with nonworking puma boards. Commit ab800e5a6f28 ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi") moved the sdram include from rk3399-puma-ddrX.dts to new files rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though. Commit 167efc2c7a46 ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux") replaced the rk3399-puma.dtsi nearly completely, but in the kernel it definitly depends on a baseboard dts to actually enable peripherals like sd-slot, uarts, etc. So to untagle this and bring the whole thing more in line with mainline Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate DDR-option devicetrees and instead replace them with a puma Kconfig option to select and include the needed DDR variant. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: fix indentation of misc_init_rHeiko Stuebner
The commit moving puma to the generic cpuid/macaddr helpers used 7 spaces as indentation, so correct that by moving to the required tabs. Fixes: fa177ff0208b ("board: puma: Use rockchip_* helpers to setup cpuid and macaddr") Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: puma: fix indentation for -u-boot.dtsiHeiko Stuebner
Tabs not spaces, so transform it to the common styling. Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07arm64: dts: rk3399-puma: fix gpio levels for vcc5v0-host regulatorHeiko Stuebner
The regulator enable-gpio uses opposite values for the declaration vs. the enable_active_low property, breaking the regulator enablement. Make the usbhost-supply work again by bringing them in sync again. This mimics the upstream Linux change found on: http://lore.kernel.org/r/20200604091239.424318-1-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2020-06-07arm64: dts: rk3399-puma: fix gpio levels for gmac reset pinHeiko Stuebner
The gmac reset has opposite values for the gpio declaration and the separate reset-active, bring this in line to make u-boot also find the ethernet-phy. This mimics the upstream Linux commit found on https://lore.kernel.org/r/20200603132836.362519-1-heiko@sntech.de Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rockpro64: add SPI bootMarcin Juszkiewicz
U-Boot TPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=16/15 CS=1 Die BW=16 Size=2048MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200) Trying to boot from SPI U-Boot 2020.07-rc3-00121-gab88251130 (Jun 03 2020 - 16:43:42 +0200) SoC: Rockchip rk3399 Reset cause: RST Model: Pine64 RockPro64 v2.1 DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe310000: 2, mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: vidconsole Err: vidconsole Model: Pine64 RockPro64 v2.1 Net: eth0: ethernet@fe300000 Hit any key to stop autoboot: 0 => Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rockpro64: Store default env into SPIMarcin Juszkiewicz
Board has flash chip on board so let store U-Boot environment there. Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07doc: rockchip: Document SPI flash program stepsJagan Teki
Document SPI flash program steps for rockchip platforms. Suggested-by: Hugh Cole-Baker <sigmaris@gmail.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07roc-rk3399-pc: Add SPI bootJagan Teki
U-Boot TPL 2020.07-rc3-00090-gd4e919f927-dirty (Jun 01 2020 - 23:45:53) Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stride 256B stride lpddr4_set_rate: change freq to 400000000 mhz 0, 1 lpddr4_set_rate: change freq to 800000000 mhz 1, 0 Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) Trying to boot from MMC1 NOTICE: BL31: v2.2(release): NOTICE: BL31: Built : 15:05:37, May 12 2020 U-Boot 2020.07-rc3-00087-ga21e9fd385 (Jun 02 2020 - 00:09:45 +0530) SoC: Rockchip rk3399 Reset cause: POR Model: Firefly ROC-RK3399-PC Board DRAM: 3.9 GiB PMIC: RK808 MMC: mmc@fe320000: 1, sdhci@fe330000: 0 Loading Environment from SPI Flash... SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Model: Firefly ROC-RK3399-PC Board Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07roc-rk3399-pc: Mark default env from SPIJagan Teki
Mark the default U-Boot environment as SPI flash since this is an on board flash device. Updated env offset, size in contrast with default since the U-Boot proper has to start from 384K. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07Makefile: Drop to handle rkspi image typeJagan Teki
On rockchip platforms, SPI boot image creation is not straightforward like MMC boot image creation where former requires to specify tpl, spl in multimage format in mkimage, and later simply do a concatenate mkimaged-tpl with spl. On this note, let drop rkspi image type creation via kbuild and let inform via rockchip.rst Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rk3399-evb: add stdout-path for the boardKever Yang
The 'stdout-path' is missing after dts sync. Fixes: 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux") Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: rk3328: add rock-pi-e-rk3328_defconfig fileb.l.huang
This commit add the default configuration file and relevant description for rock-pi-e board Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
2020-06-07rockchip: rk3328: add rock-pi-e dts fileb.l.huang
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328 Quad-Core ARM Cortex A53. Net - Dual ethernet port, 1 X Gbe, 1 X 100M USB - USB 3.0 DC - USB-Type C, 5V 2A Storage - TF card, eMMC Just build idbloader.img and u-boot.itb for Rockpi E board and follow the blow steps to replace the relevant partition. dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
2020-06-07rockchip: Enable PCIe and NVMe on ROCKPro64Mark Kettenis
Enable CONFIG_PCI and CONFIG_NVME and related configs for the ROCKPro64 board. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-07rockchip: Enable PCIe/M.2 and NVMe on Firefly RK3399Mark Kettenis
Enable CONFIG_PCI and CONFIG_NVME and related configs for the Firefly RK3399 board. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2020-06-06Merge tag 'efi-2020-07-rc4-2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-07-rc4 (2) The following problems are resolved: * When booting via UEFI an SMBIOS table is presented to the operating system. If U-Boot tries to add an empty string, this results in corrupted SMBIOS information. We will now use "Unknown" as property value. * The EFI_RNG_PROTOCOL uses the DM_RNG drivers. For the virtio RNG driver the missing DM_RNG Kconfig dependency is added. * Missing function descriptions for the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL are added.
2020-06-05efi_loader: comments EFI_SIMPLE_TEXT_OUTPUT_PROTOCOLHeinrich Schuchardt
Provide missing comments for the functions implementing the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-06-05virtio: VIRTIO_RNG depends on DM_RNGHeinrich Schuchardt
Add the missing Kconfig dependency and let VIRTIO_RNG default to yes. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-06-05smbios: empty strings in smbios_add_string()Heinrich Schuchardt
smbios_add_string() cannot deal with empty strings. This leads to incorrect property values and invalid tables. E.g. for the pine64-lts_defconfig CONFIG_SMBIOS_MANUFACTURER="". Linux command dmidecode shows: Table 1: Manufacturer: sunxi Product Name: sunxi Table 3: Invalid entry length (2). DMI table is broken! Stop. Replace empty strings by "Unknown". Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-06-04configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04Merge branch '2020-06-04-misc-bugfixes'Tom Rini
- Resync checkpatch.pl (largely) with v5.7 and introduce U-Boot specific checks in a localized area, so they aren't lost in the future. - Complete / re-migrate some options from config headers to defconfigs - Add dependencies to the various debug uart drivers
2020-06-04checkpatch.pl: Add check for defining CONFIG_CMD_xxx via config filesTom Rini
All of our cmds have a Kconfig entry. Making enabling a CMD via the config file an error to checkpatch.pl. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-04checkpatch.pl: Request if() instead #ifdefSimon Glass
There is a lot of use of #ifdefs in U-Boot. In an effort reduce this, suggest using the compile-time construct. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Request a test when a new command is addedSimon Glass
This request is made with nearly every new command. Point to some docs on how to do it. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-06-04checkpatch.pl: Warn if the flattree API is usedSimon Glass
We want people to use the livetree API, so request it. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-26 00:45:24 +0000