summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-11-03imx: mx6sl: Add perclk_clk_sel bit define in CCMYe.Li
The MX6SL has the perclk_clk_sel to select the perclk source. Add its define in CCM Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-03imx: gpt: Add High frequency clock source support for GPTYe.Li
Introduce a new configuration "CONFIG_MXC_GPT_HCLK". When it is set, the GPT will select a high frequency clock as clock source. Otherwise, the GPT will stay to use 32Khz OSC as clock source. In the implementation, since only the GPT on i.MX6 series provide the clock source option for 24Mhz OSC. For others (only i.MX5 and i.MX6 compile the driver), if the configuration is set, the perclk will be selected as clock source. MX6Q/D Rev 1.0 and MX6SL are special in the implementation, because they don't have the 24Mhz OSC clock source option, so also select the perclk for them. For MX6SL, we will set the OSC 24Mhz to perclk in CCM, so eventually the clock comes from OSC 24Mhz. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-11-03imximage: Fix the bootdata.size calculationYe.Li
In system boot chapter of i.MX6 reference manual, the "Image Vector Table" figure shows the bootdata.start points to the beginning of the destination memory. It means the bootdata.size should contain the IVT offset part, but the calculation in imximage tool does not have. We found this issue when booting from QuadSPI NOR on i.MX6SX. The u-boot runs into abnormal (crash or stop) after booting. After checked the destination memory where the image is loaded to, there are hundreds of bytes at the image end are not loaded into memory. Since there is a 4096 bytes round in the calculation, for the booting devices using smaller IVT offset, such as SD and SPI booting, they are not easy to reproduce. Signed-off-by: Ye.Li <B37916@freescale.com>
2014-10-30arm: mxs: Define bootscript env variable on m28evkMarek Vasut
The patch below failed to define the variable, so define it to make it consistent with M53EVK. commit a428ac914b2b6db851c1feac98622f2d9844db45 Author: Lothar Rubusch <lothar@denx.de> Date: Thu Jun 26 11:01:29 2014 +0200 ARM: m28evk: Update default environment Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2014-10-30arm: arch-mx6: typo fixes in crm_regs.hSoeren Moch
fix typos in video pll related register names and bit defines Signed-off-by: Soeren Moch <smoch@web.de>
2014-10-30mtd: nand: mxs: Add ECC geometry for 2048b/112b NANDMarek Vasut
Add ECC geometry for NAND which has 2048b pagesize and 112b OOB size. This is for example Macronix MX30LF2G28AB chip. Signed-off-by: Marek Vasut <marex@denx.de>
2014-10-30arm: imx6: fix typos in CCM_ANALOG_PLL_VIDEO_DENOM register nameAnatolij Gustschin
Fix name for Video PLL denominator register. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2014-10-30novena: Fix ethernet PHY reset sequenceNikolay Dimitrov
This patch fixes conflict between PHY pins becoming outputs after reset and imx6 still driving the pins. It also fixes the reset timing as recommended by the PHY datasheet. Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg> Cc: Stefano Babic <sbabic@denx.de> Cc: Sean Cross <xobs@kosagi.com> Cc: Marek Vasut <marex@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-10-30ot1200: rework card detect for eMMCChristian Gmeiner
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2014-10-30ot1200: add support for usdhc4Christian Gmeiner
On the 'mr' variant switching to 'mmc dev 1' will result in "MMC: no card present". Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2014-10-30ot1200: add feature padsChristian Gmeiner
The older 'mr' variant and the generic variant of the OT1200 differ in some places. As the name suggests the generic variant supports more boot devices. In order to be compatible with the 'mr' variant we define some 'feature' GPIOs. On the 'mr' variant this pads are not connected so we define their state with the help of the internal pullups. On the generic variant this GPIOs are connected and represent the state of the hardware. Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2014-10-30tqma6: fix typo in header guard defineMarkus Niebel
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2014-10-30tqma6: fix sf detectionMarkus Niebel
Commit 155fa9af95ac5be857a7327e7a968a296e60d4c8 changed the way to define a GPIO line, which can be used to force CS high across multiple transactions. In order to fix sf detection change board code to make use of board_spi_cs_gpio(..). Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
2014-10-30mx6sabresd: Add Seiko WVGA panel supportFabio Estevam
Add support for the 4.3'' Seiko WVGA parallel display. In order to direct the splash screen to the Seiko display: => setenv panel SEIKO-WVGA => save => reset Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2014-10-30ARM: mx6: Add support for Kosagi NovenaMarek Vasut
Add support for the Kosagi Novena board. Currently supported are: - I2C busses - FEC Ethernet - MMC0, MMC1, Booting from MMC - SATA - USB ports - USB Ethernet Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Sean Cross <xobs@kosagi.com> Cc: Nikolay Dimitrov <picmaster@mail.bg> Reviewed-by: Nikolay Dimitrov <picmaster@mail.bg>
2014-10-30board: wandboard: add usb storageJeroen Hofstee
Cc: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-10-23ot1200: add sata supportChristian Gmeiner
One of the possible boot devices can be sata. Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2014-10-23ot1200: fix sf detectionChristian Gmeiner
Commit 155fa9af95ac5be857a7327e7a968a296e60d4c8 changed the way to define a GPIO line, which can be used to force CS high across multiple transactions. In order to fix sf detection change board code to make use of board_spi_cs_gpio(..). Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-10-21mx6sabre_common: Add HDMI config to common codeFabio Estevam
HDMI config options can be placed into the common mx6sabre_common.h file to avoid duplication. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-10-21mx6qsabreauto: Add HDMI supportFabio Estevam
Let HDMI splash screen support work by default. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-10-21ot1200: remove superfluous "string" tagChristian Gmeiner
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com> Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-21ARM: i.MX video: declare displays and display_count publiclyEric Nelson
Declare displays[] and display_count in imx-common/video.h to prevent "Should it be static?" messages when compiling board files with "make C=1". Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-21ARM: i.MX: provide declaration for board_spi_cs_gpioEric Nelson
Provide a public declaration of the board_spi_cs_gpio() callback for i.MX SPI chip selects to prevent the warning "Should it be static?" when compiling with "make C=1". Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-21ARM: i.MX6: include prototype for get_board_rev()Eric Nelson
Include <asm/bootm.h> to see the prototype for get_board_rev() and prevent warning "Should it be static?" with "make C=1". Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2014-10-21ARM: prevent compiler warnings from bootm.cEric Nelson
Without preceding declarations, "make C=1" generates "Should it be static?" warnings for symbols do_bootm_linux, boot_prep_vxworks, and boot_jump_vxworks Include of bootm.h also identified a signature mismatch (const on argv[]). Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-10-14Prepare v2014.10Tom Rini
Signed-off-by: Tom Rini <trini@ti.com>
2014-10-13sunxi: axp152: dcdc3 scale is 50mV / step not 25mV / stepHans de Goede
Currently uboot wrongly uses 25mV / step for dcdc3, this is a copy and paste error introduced when adding the axp152_mvolt_to_target during review of the axp152.c driver. This results in u-boot setting Vddr to 2.3V instead of 1.5V. This commit fixes this. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-10-13Makefile: drop "tools-only" from no-dot-config-targetsTom Rini
With the introduction of CONFIG_LOCALVERSION support we cannot build tools without having a config file (as we won't know our PLAIN_VERSION until then). Reported-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Tom Rini <trini@ti.com>
2014-10-10Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2014-10-11Merge branch 'u-boot-socfpga/topic/arm/socfpga-20141010' into ↵Albert ARIBAUD
'u-boot-arm/master'
2014-10-11Merge branch 'u-boot/master' into 'u-boot-arm/master'Albert ARIBAUD
2014-10-11arm: socfpga: Use EMAC1 on SoCDKMarek Vasut
The SoCDK uses EMAC1, not EMAC0. This patch fixes the issue. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Pavel Machek <pavel@denx.de>
2014-10-11arm: socfpga: add MAINTAINERS entryPavel Machek
Add MAINTAINERS entry. Signed-off-by: Pavel Machek <pavel@denx.de> Cc: Chin Liang See <clsee@altera.com> Cc: Dinh Nguyen <dinguyen@altera.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de> Cc: Pavel Machek <pavel@denx.de>
2014-10-10tools: compiler.h: Fix build on FreeBSDJeroen Hofstee
Commit 832472 "tools: socfpga: Add socfpga preloader signing to mkimage" added tools/socfpga.c which relies on htole32, le32toh and friends. While compiler.h includes these protypes for linux from endian.h, it doesn't do so for FreeBSD. Hence include <sys/endian.h> for FreeBSD. Cc: Marek Vasut <marex@denx.de> CC: Tom Rini <trini@ti.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-10arm, at91: add generic board support for the taurus and corvus boardHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-10-10ARM: atmel: switch at91sam9263ek to generic boardBo Shen
Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-10-10sama5d3xek: run PHY's configAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Bo Shen <voice.shen@atmel.com>
2014-10-10macb: simplify gmac initialisationAndreas Bießmann
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Bo Shen <voice.shen@atmel.com>
2014-10-10serial-uclass: Fix compilation errorHans de Goede
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-10-10ks2_evm: readme: align according to actual sourcesKhoronzhuk, Ivan
Update readme file for Keystone II EVM boards to actual sources. Also correct some typos. For now the Edison evaluation board is added, README for K2E is mostly the same, so update README to contain information also for K2E evm. Rename file to README as it contains information for all keystone evm boards. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-10configs:ks2_evm: update defconfigs to support SPLMurali Karicheri
The K2HK and K2E boards support SPL by default, so add CONFIG_SPL option. Also export CONFIG_ARM, CONFIG_ARCH_KEYSTONE and TARGET_K2*_EVM options to spl/.config as they are the same. So now it's convinient to build gph images using only two commands: make k2hk_evm_defconfig make u-boot-spi.gph Acked-By: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-10-10Merge branch 'master' of git://git.denx.de/u-boot-nand-flashTom Rini
2014-10-10am335x_evm: Correct BOOTCOUNT driver supportTom Rini
We need to set the 'BE' flag here for things to work right. Signed-off-by: Tom Rini <trini@ti.com>
2014-10-10common/board_r: remove warning in initr_mem for 64-bit phys_size_tValentin Longchamp
Since on powerpc phys_size_t can be unsigned long long, this printout line can result in a not nice compile warning. Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-10board/BuR: fix pinmux for MII Ethernet InterfaceHannes Petermaier
The lines COL (collision detect) and CRS (carrier sense) needs to be connected and muxed to the CPSW MAC for a proper function in half-duplex Mode of the interface. Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at> Cc: Tom Rini <trini@ti.com>
2014-10-10scripts/multiconfig.sh: Fix a typoYork Sun
Fix the spelling of "configs". Signed-off-by: York Sun <yorksun@freescale.com> CC: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-10multiconfig.sh: replace GNU sed specific matchJeroen Hofstee
A SPL/TPL enabled target would was not recognized as such by BSD sed, since it relies on a GNU extension. Instead of or-ing just spell out both matches. Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-10VCMA9: remove EXT2 supportDavid Müller (ELSOFT AG)
remove the seldomly used EXT2 support because the U-Boot binary will not fit into the 512KiB flash otherwise. Signed-off-by: David Müller <d.mueller@elsoft.ch>
2014-10-10PATI: fix broken SPI accessDavid Müller (ELSOFT AG)
fix broken SPI access by adding/activating BOARD_EARLY_INIT_F functionality and calling spi_init_f() from there. Signed-off-by: David Müller <d.mueller@elsoft.ch>
2014-10-10PATI: convert to generic boardDavid Müller (ELSOFT AG)
Signed-off-by: David Müller <d.mueller@elsoft.ch>
generated by cgit (git 2.34.1) at 2025-01-15 21:19:55 +0000