summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-09-11ARM: uniphier: remove ad-hoc clock enabling for EHCIMasahiro Yamada
The MIO clock is enabled by default, and the STDMAC clock is enabled by the clk driver. The ad-hoc way to enable the clock is no longer needed. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11mmc: uniphier-sd: sync with LinuxMasahiro Yamada
Sync with the driver code and the binding recently merged in Linux. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11ARM: uniphier: enable CONFIG_CMD_UBIMasahiro Yamada
Now that CONFIG_SYS_MONITOR_LEN increased, we have room for enabling more options again. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11ARM: uniphier: increase CONFIG_SYS_MONITOR_LEN againMasahiro Yamada
With the migration to distro-boot, the size of the U-Boot proper image for uniphier_v7_defconfig exceeded the current limit, 576KB. Increase it to 832KB. CONFIG_SYS_UBOOT_BASE must be moved as well to avoid the image over-wrap because the boot ROM of Pro4, Pro5, PXs2/LD6b loads the SPL to the physical address 0x100000. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11ARM: dts: uniphier: sync DT with Linux 4.19-rc1Masahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-11MAINTAINERS: Add myself as the FPGA maintainerMichal Simek
FPGA subsystem requires special care that's why it should be maintained via one tree. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Fix loads commandMichal Simek
Convert last loads command to fpga subcommands. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Use CMD_RET_FAILURE instead of simple 1Michal Simek
Use standard return command failure macro. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Add support for missing fpga loadmk commandsMichal Simek
There are ways how to call fpga loadmk 1. Full command fpga loadmk [dev] [address] 2. Dev setup via variable set fpga [dev] fpga loadmk [address] 3. Address setup via variable set fpgadata [address] fpga loadmk [dev] 4. Dev and address setup via variables set fpga [dev] set fpgadata [address] fpga loadmk Before this patch only cases 1 and 3 are working but the part of code was trying to support also cases 2 and 4. This patch is adding support for cases 2 and 4 to have all of combinations supported. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Fix loadmk commandMichal Simek
Convert loadmk command to fpga subcommands. Not all combinations are working but they have never worked properly. This will be fixed later. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Fix loadfs commandMichal Simek
Convert loadfs command to fpga subcommands. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Fix dump and all direct fpga load commandsMichal Simek
Separate dump, load, loadb, loadp and loadbp commands to separate functions to make it clear how they are called and what parameters they need. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Extract fpga info command to separate functionMichal Simek
Move fpga info to U_BOOT_CMD_MKENT subcommand. Also use strtol instead of simple_strtoul. The reason is that if -1 is passed (or fpga info without "fpga" variable) the list of all fpgas is shown. This functionality is in the fpga core but it couldn't be performed. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Create new do_fpga_wrapper for using u-boot subcommandsMichal Simek
Create command wrapper to clean fpga subcommands. The function logic is taken from cmd_dm.c Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Clean wrong_parms handlingMichal Simek
There is no reason to check parameters in separate switch. Check them directly when they are read. Also there is no reason to check loadmk case separately because fpga_data address must be non zero too. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Remove parameter checking from fpga loadfs commandMichal Simek
Parameter checking is dead code because all the time there must be all params assigned. If they are not assigned there is no 9th parameters passed and checking before return CMD_RET_USAGE. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Move parameter checking for loadfs/loadsMichal Simek
There is no reason to check parameters in separate switch before main one. This patch is simplifying error path and checking parameters right after assignment. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Cleanup error handling in connection to FPGA_NONEMichal Simek
Incorrect command is already handled and FPGA_NONE should be used only one. In case of error CMD_RET_USAGE can be returned directly without any addition logic around. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Move fpga_get_op to avoid local function declarationMichal Simek
Move fpga_get_op() to top of file to remove local function declaration and also remove useless retyping. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Move error handling to do_fpga()Michal Simek
Clean fpga_get_op() error handling by moving checking/print to do_fpga. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11test/py: Extend fpga command to test all fpga load typesMichal Simek
Add support for info, load, loadp, loadb, loadbp, loadmk_legacy, loadmk_legacy_gz, loadmk_fit, loadfs also with variable support. There are probably missing failed tests. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11cmd: fpga: Remove fit image support passed without fpga deviceMichal Simek
The patch applied in 2010 "cmd_fpga: cleanup help and check parameters" (sha1: a790b5b2326be9d7c9ad9e3d9b51a8bfabc62d07" was adding this checking + if (dev == FPGA_INVALID_DEVICE) { + puts("FPGA device not specified\n"); + op = FPGA_NONE; + } which simply broke one command flow which was setenv fpga <dev> fpga loadmk <addr> // legacy image fpga loadmk <addr>:<fit_image_name> //fit image Also this sequence for FIT image is completely broken setenv fpga <dev> setenv fpgadata <addr>:<fit_image_name> fpga loadmk (Note: For legacy images this is working fine). even from code I don't think this has ever worked properly for fit image (dev = FPGA_INVALID_DEVICE should be rejected by fpga core). Fit image support was in 2008 added by: "[new uImage] Add new uImage fromat support to fpga command" (sha1: c28c4d193dbfb20b2dd3a5447640fd6de7fd0720) Just a summary of these facts that none found this for pretty long time it shouldn't be a problem to remove this flow (without fpga dev) completely to simplify the code. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-11fpga: Kconfig: Replace spaces with tabsMichal Simek
Trivial Kconfig cleanup. Use tabs instead of spaces. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-09-10cmd: part: use MAX_SEARCH_PARTITIONS for part searchKever Yang
Use Macro instead of hard code. Signed-off-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-09-10arm: armv7m: clean up armv7m unified code compilationVikas Manocha
unified syntax should be selected by config ARM_ASM_UNIFIED Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2018-09-10arm: armv7m: remove un-necessary If then instructionVikas Manocha
With gas option -mimplicit-it=always, IT block is inserted by the assembler for thumb2. Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2018-09-10arm: stm32: Remove redundant thumb build selectionVikas Manocha
All armv7m arch builds are thumb & SYS_THUMB_BUILD is already selected by CPU_ARMV7M. Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2018-09-10arm: spear: enable GPIO3 and 4 clocks when the GPIO controller driver is builtQuentin Schulz
There are multiple GPIOs that can be used with the same driver depending on the CONFIG_GPIO_BASE defined in the controller driver. GPIO3 and 4 require a clock to be enabled so let's enable them when the driver is built. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
2018-09-10tools: mkimage: Ensure munmap unmaps the same length that was mappedMark Tomlinson
The set_header call in kwbimage.c adds a checksum to the end of the image in addition to setting up the header. It 'helpfully' updates the st_size to match the fact that the file is now longer. However, mkimage uses this length in the munmap call. This can lead to unmapping an extra page, of perhaps required data. When this happens, a SEGV can occur. To prevent this from happening, the munmap call now uses the same length that was passed to mmap. This could also have been fixed by not changing the length in kwbimage.c, however changing it in the main file means that other plugins will also not fall for the same trap. Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: Chris Packham <judge.packham@gmail.com> [cp: resolve checkpatch complaints] Tested-by: Chris Packham <judge.packham@gmail.com>
2018-09-10serial: omap: Introduce DM specific omap serialLokesh Vutla
Add driver model support for OMAP_SERIAL while reusing the functions in ns16550.c Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Tested-by: Derald D. Woods <woods.technical@gmail.com>
2018-09-10omap3: pandora: Enable DM_SERIALGrazvydas Ignotas
This patch enables DM_SERIAL for the pandora board. Verified that the default kernel can still be booted with this. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2018-09-10board: arm: Add support for Broadcom BCM7260Thomas Fitzsimmons
Add support for loading U-Boot on the Broadcom 7260 SoC. This port assumes Broadcom's BOLT bootloader is acting as the second stage bootloader, and U-Boot is acting as the third stage bootloader, loaded as an ELF program by BOLT. Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com>
2018-09-10arm: bcm7445: Change serial console indexThomas Fitzsimmons
Change the configured serial console index to reflect that it is the first physical UART, reorder some defconfig lines and move some environment configuration from bcmstb.h to bcm7445.h. Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org> Cc: Florian Fainelli <f.fainelli@gmail.com>
2018-09-10ARM: CPU: arm926ejs: Consolidate cache routines to common fileAdam Ford
Four different boards had different options for enabling cache that were virtually all the same. This consolidates these common functions into arch/arm/cpu/arm926ejs/cache.c This also has the positive side-effect of enabling cache on the Davinci (da850) boards. Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Add mach-at91 to the list of consolidations] Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-10serial: arm_dcc: Add DCC support for V7R based coresLokesh Vutla
DCC is supported on Cortex R series as well. Enable DCC support for V7R. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-10pinctrl: Fix build warning with ARM64Lokesh Vutla
Following build warning appears when pinctrl-single is built for ARM64: In file included from drivers/pinctrl/pinctrl-single.c:10:0: drivers/pinctrl/pinctrl-single.c: In function ‘single_configure_pins’: ./arch/arm/include/asm/io.h:43:28: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] #define __arch_getw(a) (*(volatile unsigned short *)(a)) Fix this by using phys_addr_t for variable reg instead of u32 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-10dm: omap-timer: Update clock rate only if not populatedLokesh Vutla
timer_pre_probe() tries to populate the clock rate from DT. omap timer driver tries to overwrite this value irrespective of the value populated fro DT. So update this value only when DT doesn't populate the clock rate. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-10dm: omap-timer: Use 64bit for counter valuesLokesh Vutla
In order to handle counter overflows use 64 bit values for counter. Also load the initial value during probe. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-09-10mmc: fsl_esdhc: enable HS400 featurePeng Fan
The strobe dll code is ported from Linux Kernel: drivers/mmc/host/sdhci-esdhc-imx.c The comments are from the above file, "For HS400 eMMC, there is a data_strobe line. This signal is generated by the device and used for data output and CRC status response output in HS400 mode. The frequency of this signal follows the frequency of CLK generated by host. The host receives the data which is aligned to the edge of data_strobe line. Due to the time delay between CLK line and data_strobe line, if the delay time is larger than one clock cycle, then CLK and data_strobe line will be misaligned, read error shows up. So when the CLK is higher than 100MHz, each clock cycle is short enough, host should configure the delay target. " Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Stefano Babic <sbabic@denx.de>
2018-09-10mmc: add HS400 supportPeng Fan
Add HS400 support. Selecting HS400 needs first select HS200 according to spec, so use a dedicated function for HS400. Add HS400 related macros. Remove the restriction of only using the low 6 bits of EXT_CSD_CARD_TYPE, using all the 8 bits. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Jean-Jacques Hiblot <jjhiblot@ti.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: Marek Vasut <marex@denx.de> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-09-10at91: fix devicetree warningsEugen Hristev
This commit fixes various devicetree warnings in the at91 devicetrees like: arch/arm/dts/sama5d36ek_cmp.dtb: Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property These warnings make buildman report failed builds for most of at91 boards. Thus, fixing it. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-10ARM: dts: Makefile: fix build for at91familyEugen Hristev
For at91family, makefile was building unwanted DTBs Moved them under specific target configuration. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-10gpio: stm32f7: replace ODR update by BSRR writePatrice Chotard
Replace clrsetbits on ODR register (2 operations: one read + one write) by writing on the correct bit (SET or RESET) of the BSRR register (only 1 write operation). Moreover this register if safe for simultaneous access by 2 master on the bus. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-09-10clk: clk_meson: Add mux and div support for reparent and rate settingNeil Armstrong
This patch adds support for : - Rate calculation through muxes and generic dividers - Basic gate setting propagation - Reparenting for muxes - Clock rate setting through generic dividers without reparenting Support is only added to the Composite VPU and VAPB clocks in order to support the Video Processing Unit Power Domain clock setup. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-09-10power: domain: Add the VPU Power Domain driverNeil Armstrong
The Amlogic Meson SoCs embeds a specific Power Domain dedicated to the Video Processing Unit. This patch implements support for this power domain in preparation of the future support for the Video display support in U-Boot. This driver will depend on changes in the clock driver to handle the setup of the VPU and VAPB clocks configured from DT using assigned-clocks entries. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-09-10Remove <inttypes.h> includes and PRI* usages in printf() entirelyMasahiro Yamada
In int-ll64.h, we always use the following typedefs: typedef unsigned int u32; typedef unsigned long uintptr_t; typedef unsigned long long u64; This does not need to match to the compiler's <inttypes.h>. Do not include it. The use of PRI* makes the code super-ugly. You can simply use "l" for printing uintptr_t, "ll" for u64, and no modifier for u32. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-10arch: types.h: factor out fixed width typedefs to int-ll64.hMasahiro Yamada
All architectures have the same definition for s8/16/32/64 and u8/16/32/64. Factor out the duplicated code into <asm-generic/int-ll64.h>. BTW, Linux unified the kernel space definition into int-ll64.h a few years ago as you see in Linux commit 0c79a8e29b5f ("asm/types.h: Remove include/asm-generic/int-l64.h"). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-10Remove CONFIG_USE_STDINTMasahiro Yamada
You do not need to use the typedefs provided by compiler. Our compilers are either IPL32 or LP64. Hence, U-Boot can/should always use int-ll64.h typedefs like Linux kernel, whatever the typedefs the compiler internally uses. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-09-10arm: armv7-a: Compile and tune for armv7-a instead of armv5Adam Ford
arch/arm/Makefile references armv5 for backwards compatibility with older compilers. This patch removes those references to armv5, since by now newer compilers are required which should have armv7 support enabled. The Makefile also also has a list of options for mtune, but the entry for CONFIG_CPU_V7A is empty, so this patch tunes the CPU_V7A architecture to generic-armv7-a. The following size changed apply to omap3_logic using GCC. Stock text data bss dec hex filename 50910 429 67580 118919 1d087 spl/u-boot-spl 540713 22700 327072 890485 d9675 u-boot Without Armv5 text data bss dec hex filename 50916 429 67580 118925 1d08d spl/u-boot-spl 540719 22700 327064 890483 d9673 u-boot mtune=generic-armv7-a text data bss dec hex filename 50932 429 67580 118941 1d09d spl/u-boot-spl 540519 22700 327080 890299 d95bb u-boot Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-10sandbox: Add serial testPatrice Chotard
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2025-01-01 15:04:10 +0000