summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-04-22imx: ventana: add i210 supportTim Harvey
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22imx: ventana: disable 4k tftp/nfs packetsTim Harvey
I've encountered issues when using 4k packets through certain switches. For now disable this and go back to using MTU size packets. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22mx6: Add initial SPL support for HummingBoard-i2eXFabio Estevam
Add the initial SPL support for HummingBoard-i2eX, which is based on a MX6 Dual. For more information about HummingBoard, please check: http://www.solid-run.com/products/hummingboard/ Based on the work from Jon Nettleton and Rabeeh Khoury. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-22fdt: add new fdt_fixup_display function to configure displayTim Harvey
Add 'fdt_fixup_display' function to fixup device-tree native-mode property of display-timings node to select timings for a specific display. This is useful if a device-tree has configurations for multiple display timings for undetectable displays. see kernel Documentation/devicetree/bindings/video/display-timing.txt Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Simon Glass <sjg@chromium.org>
2015-04-22arm: mx6: ddr: add pd_fast_exit flag to system informationTim Harvey
DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit. In slow-exit mode the DLL is off but in some quiescent state that makes it easy to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK). In fast-exist mode the DLL is maintained such that it is ready again in about 3tCK. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-04-22ARM: mxs: Get boot mode from OCRAMJörg Krause
Reading the boot mode pins after power-up does not necessarily represent the boot mode used by the ROM loader. For example the state of a pin may have changed because a recovery switch which was pressed to enter USB mode is already released after plugging in USB. The ROM loader stores the value a fixed address in OCRAM. Use this value instead of reading the boot map pins. The GLOBAL_BOOT_MODE_ADDR for i.MX28 is taken from an U-Boot patch for the MX28EVK: http://repository.timesys.com/buildsources/u/u-boot/u-boot-2009.08/u-boot-2009.08-mx28-201012211513.patch Leave the boot mode detection for the i.MX23 untouched. Someone has to test whether the i.MX ROM loader does also store the boot mode in OCRAM and if the address match. This patch superseeds my incorrect patch: ARM: mxs: get boot mode from OTP http://patchwork.ozlabs.org/patch/454930/ Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks> Cc: Stefano Babic <sbabic@denx.de>
2015-04-13Prepare v2015.04Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-04-13break build if it would produce broken binaryPavel Machek
Add an error in known-bad case so that we don't produce broken and hard to debug binaries. Signed-off-by: Pavel Machek <pavel@denx.de>
2015-04-13Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2015-04-13ARM: rpi: add a couple more revision IDsStephen Warren
According to Gordon Henderson's WiringPi library, there are some more Pi revision IDs out there. Add support for them. http://git.drogon.net/?p=wiringPi;a=blob_plain;f=wiringPi/wiringPi.c;hb=5edd177112c99416f68ba3e8c6c4db6ed942e796 At least ID 0x13 is out in the wild: Reported-by: Chee-Yang Chau <cychau@gmail.com> Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2015-04-11ARM: fix arch/arm/Makefile for TegraMasahiro Yamada
Since commit 79d75d752717 (ARM: move -march=* and -mtune= options to arch/arm/Makefile), all the Tegra boards are broken because the SPL is built for ARMv7. Insert Tegra-specific code to arch/arm/Makefile to set compiler flags for an earlier ARM architecture. Note: The v1 patch for commit 79d75d752717 *was* correct when it was submitted. Notice it was originally written for multi .config configuration where Kconfig set CONFIG_CPU_V7/CONFIG_CPU_ARM720T for Tegra U-Boot Main/SPL, respectively. But, until it was merged into the mainline, commit e02ee2548afe (kconfig: switch to single .config configuration) had been already applied there. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reported-by: Stephen Warren <swarren@nvidia.com> Reported-by: Jan Kiszka <jan.kiszka@siemens.com> Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
2015-04-11arm: armada-xp: Fix SPL for AXP by using save_boot_params_retStefan Roese
Patch e11c6c27 (arm: Allow lr to be saved by board code) introduced a different method to return from save_boot_params(). The SPL support for AXP has been pulled and changing to this new method is now required for SPL to work correctly. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Cc: Luka Perkov <luka.perkov@sartura.hr>
2015-04-10Merge git://git.denx.de/u-boot-arcTom Rini
2015-04-10arc: fix separate compilation of start.oAlexey Brodkin
While testing "arc: make sure _start is in the beginning of .text section" I haven't done proper clean-up of built binaries and so missed another tiny bit that lead to the following error: --->8--- LD u-boot arc-linux-ld.bfd: cannot find arch/arc/lib/start.o Makefile:1107: recipe for target 'u-boot' failed make: *** [u-boot] Error 1 --->8--- Fix is trivial: put "start.o" in "extra-y". Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-04-10integrator: consolidate flash infoLinus Walleij
This consolidates the flash settings for the Integrator and activates the new ARM flash image support for them so images can be loaded by name from flash. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-10vexpress64: juno: add default NOR flash bootLinus Walleij
This modifies the vexpress64 Juno configuration so that it will by default load and boot a kernel and a device tree from the images stored in the NOR flash. When we are at it, also define the proper command line for the Juno and indicate that the USB stick (/dev/sda1) is the default root file system. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-10common/armflash: Support for ARM flash imagesLinus Walleij
The ARM reference designs all use a special flash image format that stores a footer (two versions exist) at the end of the last erase block of the image in flash memory. Version one of the footer is indicated by the magic number 0xA0FFFF9F at 12 bytes before the end of the flash block and version two is indicated by the magic number 0x464F4F54 0x464C5348 (ASCII for "FLSHFOOT") in the very last 8 bytes of the erase block. This command driver implements support for both versions of the AFS images (the name comes from the Linux driver in drivers/mtd/afs.c) and makes it possible to list images and load an image by name into the memory with these commands: afs - lists flash contents afs load <image> - loads image to address indicated in the image afs load <image> <addres> - loads image to a specified address This image scheme is used on the ARM Integrator family, ARM Versatile family, ARM RealView family (not yet supported in U-Boot) and ARM Versatile Express family up to and including the new Juno board for 64 bit development. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-10Merge branch 'master' of git://git.denx.de/u-boot-fdtTom Rini
2015-04-10Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini
2015-04-10common, ubi: use positive return values for ubi checkStefan Agner
The ubi check command is expected to not fail and just check whether a volume exist or not. Currently, when a volume does not exist, the command fails which leads to an error: "exit not allowed from main input shell." Use 1 to indicate that a volume does not exist. This allows to use ubi check in an if statement, e.g. if ubi check rootfs; then; echo "exists"; else; echo "not there"; fi
2015-04-10arc: make sure _start is in the beginning of .text sectionAlexey Brodkin
This is important to have entry point in the beginning of .text section because it allows simple loading and execution of U-Boot. For example pre-bootloader loads U-Boot in memory starting from offset 0x81000000 and then just jumps to the same address. Otherwise pre-bootloader would need to find-out where entry-point is. In its turn if it deals with binary image of U-Boot there's no way for pre-bootloader to get required value. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-04-10fdt: nios: Fix warning in ft_cpu_setup()Simon Glass
This function should not return a value. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Thomas Chou <thomas@wytron.com.tw>
2015-04-10lpc32xx: add support for board work_92105Albert ARIBAUD \(3ADEV\)
Work_92105 from Work Microwave is an LPC3250- based board with the following features: - 64MB or 128MB SDR DRAM - 1 GB SLC NAND, managed through MLC controller. - Ethernet - Ethernet + PHY SMSC8710 - I2C: - EEPROM (24M01-compatible) - RTC (DS1374-compatible) - Temperature sensor (DS620) - DACs (2 x MAX518) - SPI (through SSP interface) - Port expander MAX6957 - LCD display (HD44780-compatible), controlled through the port expander and DACs This board has SPL support, and uses the LPC32XX boot image format. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10Introduce CONFIG_SPL_PANIC_ON_RAW_IMAGEAlbert ARIBAUD \(3ADEV\)
introduce CONFIG_SPL_PANIC_ON_RAW_IMAGE. An SPL which define this will panic() if the image it has loaded does not have a mkimage signature. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: add lpc32xx-spl.bin boot image targetAlbert ARIBAUD \(3ADEV\)
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10dtt: add ds620 supportAlbert ARIBAUD \(3ADEV\)
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: add LPC32xx SSP support (SPI mode)Albert ARIBAUD \(3ADEV\)
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: add GPIO supportAlbert ARIBAUD \(3ADEV\)
This driver only supports Driver Model, not legacy model. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: i2c: add LPC32xx I2C interface supportAlbert ARIBAUD \(3ADEV\)
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: mtd: nand: add MLC NAND controllerAlbert ARIBAUD \(3ADEV\)
The controller's Reed-Solomon ECC hardware is used except of course for raw reads and writes. It covers in- and out-of-band data together. The SPL framework is supported. Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10lpc32xx: add Ethernet supportAlbert ARIBAUD \(3ADEV\)
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2015-04-10Merge branch 'u-boot/master'Albert ARIBAUD
2015-04-09omap3: pandora: use common configurationGrazvydas Ignotas
This allows to clean up the config a good deal and also converts pandora to Generic Board. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
2015-04-09odroid-XU3: update board maintainerPrzemyslaw Marczak
At present Hyungwon can't take care of this board in U-Boot, so I will keep it working. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Hyungwon Hwang <human.hwang@samsung.com>
2015-04-09mcx: update maintainer and convert to generic boardAnatolij Gustschin
Remove obsolete email address from MAINTAINERS. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Tom Rini <trini@konsulko.com>
2015-04-09MAINTAINERS: fix TI DaVinci directory path and add KeyStoneMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-04-09board: axs10x - support v3 mother-boardAlexey Brodkin
There're 2 versions of motherboards that could be used in ARC SDP. The only important difference for U-Boot is different NAND IC in use: [1] v2 board (we used to support up until now) sports MT29F4G08ABADAWP while [2] v3 board sports MT29F4G16ABADAWP They are almost the same except data bus width 8-bit in [1] and 16-bit in [2]. And for proper support of 16-bit data bus we have to pass NAND_BUSWIDTH_16 option to NAND driver core - which we do now knowing board type we're running on. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2015-04-09ARM: mx5: add support for USB armory boardAndrej Rosano
Add support for Inverse Path USB armory board, an open source flash-drive sized computer based on Freescale i.MX53 SoC. http://inversepath.com/usbarmory Signed-off-by: Andrej Rosano <andrej@inversepath.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Chris Kuethe <chris.kuethe@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Vagrant Cascadian <vagrant@debian.org> Tested-By: Vagrant Cascadian <vagrant@debian.org> Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
2015-04-09ARM: mx5: move to a standard arch/board approachAndrej Rosano
Move the MX5 based boards to arch/arm/cpu/armv7/mx5, following the commit: 89ebc82137bebb11a8191f8b9cbf08f2533ae8bc Signed-off-by: Andrej Rosano <andrej@inversepath.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Vagrant Cascadian <vagrant@debian.org> Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
2015-04-08ARM: zynq: Remove Jagan from list of maintainersMichal Simek
Email address is not longer valid that's why remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-04-08ARM: zynq: disable CONFIG_SYS_MALLOC_F to fix MMC bootMasahiro Yamada
Since commit 326a682358c1 (malloc_f: enable SYS_MALLOC_F by default if DM is on), Zynq MMC boot hangs up after printing the following: U-Boot SPL 2015.04-rc5-00053-gadcc570 (Apr 08 2015 - 12:59:11) mmc boot reading system.dtb Prior to commit 326a682358c1, Zynq boards enabled CONFIG_DM, but not CONFIG_SYS_MALLOC_F. That commit forcibly turned on CONFIG_SYS_MALLOC_F. I have not figured out the root cause, but anyway it looks like CONFIG_SYS_MALLOC_F gave a bad impact on the Zynq MMC boot. We are planning to have the v2015.04 release in a few days. I know this is a defensive fixup, but what I can do now is to add # CONFIG_SYS_MALLOC_F is not set to every Zynq defconfig file to get back the original behavior. Tested on: - Zedboard - ZC706 board Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Cc: Simon Glass <sjg@chromium.org>
2015-04-08Fix mxc_hab documenation for DEK blob generationUlises Cardenas
Include/fsl_sec.h defines sec_in and sec_out, according to the platform's endianess. Therefore, CONFIG_SYS_FSL_LE needs to be declared in the configuration file of the target, in order to use enable the DEK blob generation command. This requirement is not explicit in the README.mxc_hab. Signed-off-by: Ulises Cardenas <Ulises.Cardenas@freescale.com>
2015-04-08mx53loco: Disable printing cpuinfoFabio Estevam
Since commit 32df39c741788e ("mx5: fix get_reset_cause") we have the following boot messages on a mx53qsb: U-Boot 2015.04-rc5-00029-gd68df02 (Apr 06 2015 - 11:15:39) CPU: Freescale i.MX53 rev2.1 at 800 MHz Reset cause: POR Board: MX53 LOCO I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 In: serial Out: serial Err: serial CPU: Freescale i.MX53 rev2.1 at 1000 MHz Reset cause: unknown reset Net: FEC [PRIME] The CPU and Reset cause lines appear twice. Initially mx53 boots at 800MHz, then at a later point the PMIC is configured via I2C to raise the CPU voltage so that it can run at 1GHz. To avoid such misleading double printings, disable printing cpu info for now. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Jason Liu <r64343@freescale.com>
2015-04-07cmd_mem.c: Update 'iteration_limit' to unsigned longTom Rini
With e37f1eb we now use strict_strtoul() in do_mem_mtest() and this gives us a warning: ../include/vsprintf.h:38:5: note: expected 'long unsigned int *' but argument is of type 'int *' Signed-off-by: Tom Rini <trini@konsulko.com>
2015-04-07fix makefiles to respect DTC settingPavel Machek
Top-level Makefile has option to select dtc binary, but it is ignored due to bug in Makefile.lib. Fix it. Signed-off-by: Pavel Machek <pavel@denx.de>
2015-04-07MAKEALL: fix get_target_arch() to adjust to '-' in Status fieldMasahiro Yamada
Since the Kconfig conversion, boards.cfg scanned by MAKEALL is generated by tools/genboardscfg.py. Every board is supposed to have its own MAINTAINERS that contains maintainer and status information, but, in fact, MAINTAINERS is missing from some boards. For such boards, the first field, Status, is filled with '-'. It causes a problem for "set" command, which ignores '-' in its arguments. Consequently, get_target_arch() returns a wrong field and MAKEALL fails to get a correct toolchain. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2015-04-07kbuild: include config.mk when auto.conf is not older than .configMasahiro Yamada
Since the Kconfig conversion, config.mk has been included only when include/config/auto.conf is newer than the .config file. It causes build error if both files have the same time-stamps. It is actually possible because EXT* file systems have a 1s time-stamp resolution. The config.mk should be included when include/config/auto.conf is *not older* than the .config file. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reported-by: Tom Rini <trini@konsulko.com> Reported-by: York Sun <yorksun@freescale.com> Reported-by: Stephen Warren <swarren@nvidia.com> Reported-by: Matthew Gerlach <mgerlach@opensource.altera.com> Tested-by: Stephen Warren <swarren@nvidia.com>
2015-04-07am33xx/ddr.c: Fix regression on DDR2 platformsTom Rini
Back in fc46bae a "clean up" was introduced that intended to reconcile some of the AM335x codepaths based on how AM43xx operates. Unfortunately this introduced a regression on the DDR2 platforms. This was un-noticed on DDR3 (everything except for Beaglebone White) as we had already populated sdram_config correctly in sequence. This change brings us back to the older behavior and is fine on all platforms. Tested on Beaglebone White, Beaglebone Black and AM335x GP EVM Reported-by: Matt Ranostay <mranostay@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2015-04-07cmd_mem: cleanups, catch bad usagePavel Machek
Currently, memtest will silently accept bad data. Perform error checking on user intput. Signed-off-by: Pavel Machek <pavel@denx.de>
2015-04-07ahci: Fix a wrong parameter passTang Yuantian
In stead of user_buffer_size, transfer_size should be used to pass to ahci_device_data_io(). transfer_size is the length that we want the low level function to transfer each time. If we use user_buffer_size which is the totally data length as parameter, low level function will actually create many SGs to transfer as many data as possible each time. That will produce many redundant data transfer. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Reviewed-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-29 07:15:30 +0000