| Age | Commit message (Collapse) | Author |
|---|
|
The ending LBA is inclusive. Hence, the partition size should be
((ending-LBA + 1) - starting-LBA) to get the proper partition size.
This is confirmed against the results from the parted tool.
(e.g. use parted /dev/sda -s unit S print) and observe the size.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
|
|
This patch fixes a bug (?) introduced after inclusion of the new
JFFS2 code.
When not using CONFIG_JFFS2_CMDLINE, the code in cmd_jffs2.c doesn't
fill in part->sector_size (keeping it as 0), but a correct value is
needed by the code in jffs2_1pass.c. This causes all JFFS2 accesses
to be in the same place of the memory, what obviously means
impossibility to use the JFFS2 partition.
This problem is fixed in this patch by including sector size
calculation in non-CONFIG_JFFS2_CMDLINE mtdparts_init variant.
Signed-off-by: Tomasz Figa <tomasz.figa_at_gmail.com>
|
|
Rather than special casing each environment type for enabling the saveenv
command, have them all behave the same. This avoids bitrot as new env
sources are added/removed.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This patch adds a #define to optionally change the behaviour of
i2c_read() in soft_i2c.c to send an I2C repeated start instead of a
stop-start between sending the device address pointer write and
reading back the data. The current behaviour is retained as the
default.
While most devices will work either way, I have a smart battery(*)
that requires repeated start, and someone at some point found a
device that required a stop-start.
(*) http://www.inspired-energy.com/Standard_Products/NL2054/NL2054%20Rev1.0%20Data%20Sheet.pdf
Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
|
|
Commit 9d803d8c mistakenly changed some constants
from 0x300 into 300 - this patch fixes it.
Pointed out by Tom Evans <tom@ceos.com.au>, see
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/51992 for
details.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Stefan Althoefer <stefan.althoefer@web.de>
|
|
Fix based on suggestion by David Hawkins <dwh@ovro.caltech.edu>.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
U-Boot's gunzip() function does not handle the return code
of zlib's inflate() function correctly. gunzip() is implemented
to uncompress all input data in one run. So the correct return
code for the good case is Z_STREAM_END. In case of insufficient
output buffer memory inflate returns Z_OK. For gunzip() this
is an error.
It also makes sense to me to call inflateEnd() also in case
of an error.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
|
|
|
|
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch adds flush_/invalidate_dcache_range() to the MIPS architecture.
Those functions are needed for the upcoming dcache support for the USB
EHCI driver. I chose this API because those cache handling functions are
already present in the PPC architecture.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
|
This patch removes the now obsolete and additionally wrongly defined
board_nand_init() prototype from nand_spl/nand_boot.c.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Added flash_fixup_stm to fix geometry reversal on STMicro M29W320ET flash chip.
Modeled after flash_fixup_amd, this patch handles the geometry reversal
or erase sectors that exist for ST Micro (now Numonyx) M29W320ET flash.
Since I cannot test all STM's chips, the detection is implemented as
narrow as possible for now.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Tested on TQM5200S-BD with Samsung K8P2815UQB
Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The function find_sector() doesn't need to be called twice in
the case of AMD command set.
Tested on TQM5200S-BD with Samsung K8P2815UQB.
Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Lot's of 405 board config files use CONFIG_SYS_IGNORE_405_UART_ERRATA_59.
Either they define or undef it. Because it's not used in any source
files this patch removes any references to it.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Board support for the Guntermann & Drunck PowerPC 440 ETX module.
Based on the AMCC Yosemite board support by Stefan Roese.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Added support for a second memory bank to DDR autodetection for 440
platforms.
Made hardcoded values configurable.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add CONFIG_NET_MULTI in config file, because sh_eth changed new newwork API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
This change is needed for mgcoge because it uses two ethernet drivers.
Add a check for the presence of the PIGGY board on mgcoge. Without this
board networking cannot work and the initialization must be aborted.
Only allocate rtx once to prevent DPRAM exhaustion.
Initialize ether_scc.c and the keymile-specific HDLC driver (to be added
soon) in eth.c.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
sh_eth used old network API. This patch changed new API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
This patch changes the reg_read/_write to smc911x_reg_read/_write
and defines then as weak so that they can be overridden by board
specific version.
This will be used by the upcoming VCTH board support.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
|
|
The NMDK8815 board is distributed by ST Microelectornics.
Other (proprietary) code must be run to unlock the CPU before
U-Boot runs. doc/README.nmdk8815 outlines the boot sequence.
This is the initial port, with basic infrastructure and
a working serial port.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Add I2C support.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
Add MMC support.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
Add NAND support.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
Add common board, interrupt and system info code.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
Add common clock, memory and low level code
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
Add common cpu and start code.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
Add OMAP3, memory and function prototype header files for OMAP3.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
Add pin mux, clock and cpu header files for OMAP3.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
Signed-off-by: Maxim Artamonov <scn1874 at yandex.ru>
|
|
|
|
|
|
Some images can be quite large, so add an option to compress the
image data with gzip in the U-Boot image. Then at runtime, the
board can decompress it with the normal zlib functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
A couple of buffers in the fat code are declared as an array of bytes.
But it is then cast up to a structure with 16bit and 32bit members.
Since GCC assumes structure alignment here, we have to force the
buffers to be aligned according to the structure usage.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Higher spi flash layers expect to be given back a pointer that was
malloced so that it can free the result, but the lower layers return
a pointer that is in the middle of the malloced memory. Reorder the
members of the lower spi structures so that things work out.
Signed-off-by: Brad Bozarth <bflinux@yumbrad.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
When compile u-boot with the 2.18 binutils the following
warning messages for each object file in post/lib_ppc/fpu/ is
produced at the linking stage:
post/libpost.a(acc1.o) uses hard float, u-boot uses soft-float
...
This is because of the fact that, in general, the soft-float and
hard-float ABIs are incompatible; the 2.18 binutils do checking
of the Tag_GNU_Power_ABI_FP attribute of the files to be linked, and
produce the worning like above if these are not compatible.
The incompatibility of ABIs is concerned only the float values:
e.g. the soft-float ABI assumes the float argument passing in the
pair of rX registers, and the hard-float ABI assumes passing of
the float argument in the fX register. When we don't pass the float
arguments between the functions compiled with different floatness,
then such an application will work correctly.
This is the case for the FPU POST: u-boot (compiled with soft-float)
doesn't pass to (and doesn't get from) the FPU POST functions any
floats; there are no functions exported from the post/lib_ppc/fpu/
objects which would work with float parameters/returns too. So, we
can reassure the linker not to worry about the difference in ABI
attributes of linking files just by setting the 'soft-float'
attribute for the objects in post/lib_ppc/fpu. And this patch does
this.
Also, to avoid passing both soft- and hard-float options in CFLAGS
when compiling the files from post/lib_ppc/fpu (which is OK, but
looks rather dirty) this patch removes the soft-float string from
CFLAGS in post/lib_ppc/fpu/Makefile.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
|
|
Initial support for the DS4510, a CPU supervisor with
integrated EEPROM, SRAM, and 4 programmable non-volatile
GPIO pins. The CONFIG_DS4510 define enables support
for the device while the CONFIG_CMD_DS4510 define
enables the ds4510 command. The additional
CONFIG_DS4510_INFO, CONFIG_DS4510_MEM, and
CONFIG_DS4510_RST defines add additional sub-commands
to the ds4510 command when defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
The iteration limit is passed to mtest as a fourth parameter:
[start [end [pattern [iterations]]]]
If no fourth parameter is supplied, there is no iteration limit and the
test will loop forever.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
|
|
Moved driver vcth.c to vct.c to better reflect the VCT board series.
This driver is now used by the VCT platforms:
vct_premium
vct_platinum
vct_platinumsvc
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
|
Support bootdelay=0 in abortboot for the CONFIG_AUTOBOOT_KEYED case
similar to the CONFIG_ZERO_BOOTDELAY_CHECK support for the
!CONFIG_AUTOBOOT_KEYED case.
Do this by reversing the loop so we do at least one iteration before
checking for timeout.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
|
|
|
