summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-08-22nand_util: delete a useless variableMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-22cmd_nand: Do not show usage when scrub is abortedMasahiro Yamada
When executing nand scrub, the user gets the prompt: Really scrub this NAND flash? <y/N> We do not want the annoying usage displayed when saying N here. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-22cmd_nand: slight optimization of nand_dump functionMasahiro Yamada
If a non-zero value is given to only_oob argument, printing the main area is skipped. With a little modification, we can skip the whole while loop. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-22cmd_nand: fix a memory leak in nand_dump functionMasahiro Yamada
If datbuf = memalign(ARCH_DMA_MINALIGN, nand->writesize); succeeds and oobbuf = memalign(ARCH_DMA_MINALIGN, nand->oobsize); fails, nand_dump function should free databuf. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-08-22arm: atmel: cpux9k2: board update and enhancementJens Scharsig (BuS Elektronik)
- fix adresses in env settings in config header - add missing CONFIG_STANDALONE_LOAD_ADDR to eb_cpux9k2 config header - remove jffs2 support, board doesn't use this anymore - add ubifs support - change sizes and start for partitions Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22gpio: atmel: add copyright and remove error header infoBo Shen
Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Jens Scharsig <js_at_ng@scharsoft.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22gpio: atmel: add gpio common API supportBo Shen
add gpio common API support for gpio command Signed-off-by: Bo Shen <voice.shen@atmel.com> [fix unnecessary cast] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22gpio: atmel: fix code to use pointer for pio portBo Shen
fix code to use pointer for pio port as the warning message suggested remove the warning message Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: atmel: remove the config.mk fileBo Shen
remove the config.mk file move text base define to board config file for following boards - at91sam9m10g45ek - at91sam9x5ek Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: atmel: sama5d3: fix typo error for CONFIG_ENV_IS_NOWHEREBo Shen
fix typo error for CONFIG_ENV_IS_NOWHERE from CONIG_ENV_IS_NOWHERE Signed-off-by: Bo Shen <voice.shen@gmail.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: sama5d3: remove unused defineBo Shen
The CONFIG_MAX_NAND_CHIPS never used, remove it No where define LCD_TEST_PATTERN, so no need undefine Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: sama5d3: fix smc cs related registers offsetBo Shen
the smc cs related registers start at 0x600 and loop with 5 registers so the reserved register should be in at91_smc structure while no in at91_cs structure. So fix it Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22ARM: at91: atmel_nand: add code to check the ONFI parameter ECC requirementWu, Josh
1. if CONFIG_SYS_NAND_ONFI_DETECTION is defined, driver will check NAND flash's ecc minimum requirement in ONFI parameter. a) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are defined. then use it. Driver will display a WARNING if the values are different from ONFI parameters. b) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are not defined, then use the value from ONFI parameters. * If ONFI ECC parameters are in ONFI extended parameter page, since we are not support it, so assume the minimum ecc requirement is 2 bits in 512 bytes. * For non-ONFI support nand flash, also assume the minimum ecc requirement is 2 bits in 512 bytes. 2. if CONFIG_SYS_NAND_ONFI_DETECTION is not defined, just use CONFIG_PMECC_CAP and CONFIG_PMECC_SECTOR_SIZE. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22mtd: atmel_nand: alloc memory instead of use static array for pmecc dataWu, Josh
In this way, the pmecc corraction capbility can change in run time. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22linux/compat.h: move dev_err, dev_info and dev_dbg from usb driver to compat.hWu, Josh
Since kernel code current use many dev_xxx() instead of using printk. To compatible, move those dev_xxx from usb driver to linux/compat.h. Then all driver code can use dev_err, dev_info and dev_vdbg. This patch also removed duplicated macro definitions in usb driver. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22ARM: at91: sama5d3: remove unused definition about PMECC alpha table offsetWu, Josh
Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22ARM: at91: atmel_nand: pmecc driver will select the galois table by sector sizeWu, Josh
Define the galois index table offset in chip head file. So user do not need to set by himself. Driver will set it correctly according to sector_size. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Scott Wood <scottwood@freescale.com> [rebased on master] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: atmel: add nand trimffs subcommand for at91sam9n12 and at91sam9x5Bo Shen
as the at91sam9n12 and at91sam9x5 soc support PMECC, when use u-boot to flash the rootfs, in order to avoid flash one sector with all 0xff into NAND, so use nand trimffs subcommand to avoid it Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22arm: atmel: add gmac support for sama5d3xek boardBo Shen
add gmac support for sama5d3xek board, the gmac embedded in: - sama5d33, sama5d34, sama5d35 Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-22net: macb: fix the following building warningBo Shen
fix the following building warning ---8>--- macb.c: In function 'macb_init': macb.c:400:14: warning: 'phydev' may be used uninitialized in this function macb.c:377:21: note: 'phydev' was declared here ---<8--- Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-08-21Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2013-08-21fec_mxc: set ethaddr if fuses burned and not previously setEric Nelson
Without this change, the following message is generated: Warning: FEC using MAC address from net device See doc/README.enetaddr for details. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-08-21ARM: mxs: Add mx28evk_auart_console targetAndreas Wass
The target uses AUART 3 instead of the DUART for console output. Signed-off-by: Andreas Wass <andreas.wass@dalelven.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Marek Vasut <marex@denx.de>
2013-08-21ARM: mxs: Added application UART driverAndreas Wass
The driver makes it possible to use an application UART as the U-Boot output console for Freescale i.MX23/i.MX28 devices. Signed-off-by: Andreas Wass <andreas.wass@dalelven.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Marek Vasut <marex@denx.de> Acked-by: Marek Vasut <marex@denx.de>
2013-08-21i.MX6: nitrogen6x: force HDMI onto IPU0/DI0Eric Nelson
Our Linux kernel switches the HDMI connector onto IPU0/DI1, but the U-Boot display driver only supports IPU0/DI0 for the time being. Because of this, a soft re-boot will leave the HDMI output connected to the wrong display port and prevent video from being displayed. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-08-21Makefile: Fix build in a separated directory treeYork Sun
Fix a bug introduced by commit 3aa29dee TPL : introduce the TPL based on the SPL Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-20Fix for incorrect conversion hex string to number (FMAN firmware address).Николай Пузанов
Signed-off-by: Николай Пузанов <punzik@gmail.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc/sec: Add workaround for SEC A-003571Shengzhou Liu
Multiple read/write transactions initiated by security engine may cause system to hang. Workaround: set MCFGR[AXIPIPE] to 0 to avoid hang. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc/p1010rdb: fix calculating ddr_freq_mhzShengzhou Liu
There was a bug for calculating ddr_freq_mhz, it should be divided by 1000000 rather than 0x1000000. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc/t4240: add QSGMII interface supportShaohui Xie
Also some fix for QSGMII. 1. fix QSGMII configure of Serdes2. 2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN. 3. fix dtb for QSGMII interface. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc/t4240: fix lanes routing for QSGMII protocolsShaohui Xie
When using QSGMII protocols, the first lane and third lane on each slot need to be swapped. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc/common/vsc3316: remove const from vsc3316_config parameter defineShaohui Xie
Since the parameters need to be modified according to different Serdes protocols at runtime, the const will block this. Also remove const from arrays define used by vsc3316_config. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpcv2: Print hardcoded size like print_size() doesShruti Kanetkar
Makes the startup output more consistent Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: Use print_size() where appropriateShruti Kanetkar
Makes the startup output more consistent Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com> Acked-by: Andy Fleming <afleming@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20SPDX-License-Identifier: clean up license headerYork Sun
This patch cleans up license header in these files: board/freescale/p1022ds/spl.c drivers/mmc/fsl_esdhc_spl.c drivers/mtd/spi/fsl_espi_spl.c Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: Fix CamelCase checkpatch warningsPrabhakar Kushwaha
85xx, 86xx PowerPC folders have code variables with CamelCase naming conventions. because of this code checkpatch script generates "WARNING: Avoid CamelCase". Convert variables name to normal naming convention and modify board, driver files with updated the new structure. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: p1022ds: add TPL for p1022ds nand bootYing Zhang
TPL is introduced in the patch "NAND: TPL : introduce the TPL based on the SPL", here enable TPL for p1022ds nand boot. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20TPL : introduce the TPL based on the SPLYing Zhang
Due to the nand SPL on some board(e.g. P1022DS)has a size limit, it can not be more than 4K. So, the SPL cannot initialize the DDR with the SPD code. This patch introduces TPL to enable a loader stub that is loaded by the code from the SPL. It initializes the DDR with the SPD or other operations. The TPL's size is sizeable, the maximum size is decided by the memory's size that TPL runs. It initializes the DDR through SPD code, and copys final uboot image to DDR. So there are three stage uboot images: * spl_boot, * tpl_boot, * final uboot image Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc : p1022ds : Enable p1022ds to start from eSPI with SPLYing Zhang
Enable p1022ds to start from eSPI with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc : spi flash : Support to start from eSPI with SPLYing Zhang
This patch introduces SPL to enable a loader stub that being loaded by the code from the internal on-chip ROM. It loads the final uboot image into DDR, then jump to it to begin execution. The SPL's size is sizeable, the maximum size must not exceed the size of L2 SRAM. It initializes the DDR through SPD code, and copys final uboot image to DDR. So there are two stage uboot images: * spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that ddr spd code can get the interleaving mode setting in env. It loads final uboot image from offset 96KB. * final uboot image, size is variable depends on the functions enabled. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: p1022ds: Enable P1022DS to boot from SD Card with SPLYing Zhang
Enable p1022ds to start from eSDHC with SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: mpc85xx: Support booting from SD Card with SPLYing Zhang
The code from the internal on-chip ROM. It loads the final uboot image into DDR, then jump to it to begin execution. The SPL's size is sizeable, the maximum size must not exceed the size of L2 SRAM. It initializes the DDR through SPD code, and copys final uboot image to DDR. So there are two stage uboot images: * spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that ddr spd code can get the interleaving mode setting in env. It loads final uboot image from offset 96KB. * final uboot image, size is variable depends on the functions enabled. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20powerpc: deleted unused symbol CONFIG_SPL_NAND_MINIMAL and enabled some ↵Ying Zhang
functionality for common SPL 1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it. 2. Some functions were unused in the minimal SPL, but it is useful in the common SPL. So, enabled some functionality for common SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20spl: env_common.c: make CONFIG_SPL_BUILD contain function env_importYing Zhang
The functionality env_import will be used in the SPL. They had been excluded by ifndef CONFIG_SPL_BUILD. Now, put it into the SPL. Signed-off-by: Ying Zhang <b40530@freescale.com> Acked-by: Tom Rini <trini@ti.com> Acked-by: York Sun <yorksun@freescale.com>
2013-08-20ppc4xx: Remove support for PPC405CR CPUsMatthias Fuchs
This patch removes support for the APM 405CR CPU. This CPU is EOL and no board uses this chip. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
2013-08-20ppc4xx: Remove CANBT boardMatthias Fuchs
This board and especially the CPU (PPC405CR) is EOL. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu> Acked-by: Wolfgang Denk <wd@denx.de>
2013-08-20Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2013-08-20pmic:i2c: Replace legacy I2C_SET_BUS macro with i2c_set_bus_num()Łukasz Majewski
After introduction of unified i2c model, the I2C_SET_BUS() macro is regarded as obsolete. Hence it is replaced with i2c_set_bus_num() function call. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
2013-08-20i2c:samsung: Adjust Trats, GONI and Universal_c210 boards to work with new ↵Łukasz Majewski
I2C framework New I2C framework, introduced after v2013.07 final release, imposed I2C code adjustment for some Samsung boards - namely Trats, GONI and Universal_c210. Those boards were using schematic based I2C enumeration (I2C_5, I2C_9). However, new I2C framework imposes usage of logical I2C adapters numbering (e.g. I2C_0, I2C_1, etc). Additionally, I2C_GET_* macros were replaced with i2c_*_bus_num() functions. Trats board gained definition of second soft I2C adapter. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Heiko Schocher <hs@denx.de>
2013-08-20i2c:multibus:fix: Correct I2C_MULTI_BUS value when support for many buses is ↵Łukasz Majewski
enabled The I2C_MULTI_BUS needs to be defined for correct I2C operation with many software emulated I2C controllers. This fix restores correct value of the I2C_MULTI_BUS changed by following commit: SHA1: 385c9ef5a7215b2b0c22836fee6c692dfc8559d7 i2c: add i2c_core and prepare for new multibus support Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Heiko Schocher <hs@denx.de>
generated by cgit (git 2.34.1) at 2025-02-13 11:29:52 +0000