summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-01-14efi_loader: Add a wchar_t cast in efi_file_open()Simon Glass
The printf() string here is not actually correct. Add a cast to avoid a warning when checking is enabled. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-01-14sandbox: Correct SDL build flagsSimon Glass
The check for CONFIG_SANDBOX_SDL in config.mk does not work since the build config is not available by the time that file is included. Remove it so that we always call sdl-config except when NO_SDL is used. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-01-14buildman: Deal nicely with invalid build-status fileSimon Glass
The 'done' files created by buildman may end up being empty if buildman runs out of disk space while writing them. This error is then persistent, since even if disk space is reclaimed and the build retries, the empty file causes an exception in the builder thread. Deal with this silently by doing a rebuild. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-01-14test: dm: regmap: Fix the long test delaySimon Glass
At present one of the regmap tests takes 5 seconds to run since it waits for a timeout. This should be handled using sandbox_timer_add_offset() which advances time for test purposes. This requires a little change to make the regmap_read_poll_timeout() testable. Update the macro and the test. Fixes: ebe3497c9c ("test: regmap: add regmap_read_poll_timeout test") Signed-off-by: Simon Glass <sjg@chromium.org>
2019-01-14common: fdt_support: print hexadecimal numbers in debugSekhar Nori
We usually deal with hexadecimal addresses and sizes in device-tree. Its much easier if debug logs print hexadecimal values too. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-01-14dm: Tidy up 'dm tree' output when there are many devicesSimon Glass
At present the 'Index' column assumes there is only one digit. But on some devices (e.g. snow) there are a lot of regulators and GPIO banks. Adjust the output to allow for two digits without messing up the display. Also capatalise the heading to match. Fixes: 5197dafc42 (dm: core: Widen the dump tree to show more of the driver's name.) Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Liviu Dudau <liviu.dudau@foss.arm.com>
2019-01-14buildman: Drop comment about Ctrl-C problemSimon Glass
This bug is now fixed, so drop this comment. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-01-14sandbox: add memset_io(..), memcpy_fromio(..) and memcpy_toio(..)Christian GMEINER
These functions could be used by drivers. Signed-off-by: Christian GMEINER <christian.GMEINER@bachmann.info> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-01-14Prepare v2019.01Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-14mmc: fsl_esdhc: Avoid infinite loop in esdhc_send_cmd_common()Fabio Estevam
The following hang is observed on a Hummingboard 2 MicroSOM i2eX iMX6D - rev 1.3 with no eMMC populated on board: U-Boot SPL 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000) Trying to boot from MMC1 U-Boot 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000) CPU: Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz) CPU: Extended Commercial temperature grade (-20C to 105C) at 33C Reset cause: POR Board: MX6 HummingBoard2 DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment No panel detected: default to HDMI Display: HDMI (1024x768) In: serial Out: serial Err: serial ---> hangs which is caused by the following infinite loop inside esdhc_send_cmd_common() while (!(esdhc_read32(&regs->irqstat) & flags)) ; Instead of looping forever, provide an exit path so that a timeout error can be propagated in the case irqstat does not report any interrupts, which may happen when no eMMC is populated on board. Reported-by: Ricardo Salveti <rsalveti@rsalveti.net> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Tested-by: Ricardo Salveti <rsalveti@rsalveti.net>
2019-01-14imx8mq_evk_defconfig: Move file system options to KconfigFabio Estevam
Chris Spencer reports that when enabling ext4 read support without also enabling write support the following error is seen: fs/fs.c:198:12: error: 'ext4_write_file' undeclared here (not in a function); did you mean 'ext4_read_file'? .write = ext4_write_file, ^~~~~~~~~~~~~~~ Fix this problem by moving these options to Kconfig. Reported-by: Chris Spencer <spencercw@gmail.com> Acked-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-01-14poplar: save environment at a different offsetAlex Elder
Change CONFIG_ENV_OFFSET for Poplar to be 1MB further into the eMMC than before. This puts it immediately prior to the space we are reserving offset 0x200000-0x400000 for UEFI to save its persistent data. Define CONFIG_ENV_SIZE as a product of env_mmc_nblks and the sector size, like CONFIG_ENV_OFFSET is. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2019-01-11Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2019-01-11Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2019-01-11Revert "fs: fat: assign rootdir sector when accessing root directory"Tom Rini
This particular commit is causing a regression on stih410-b2260 and other platforms when reading from FAT16. Noting that I had rebased the original fix from Thomas onto then-current master, there is also question from Akashi-san if the change is still needed after other FAT fixes that have gone in. This reverts commit a68b0e11ea774492713a65d9fd5bb525fcaefff3. Reported-by: Patrice Chotard <patrice.chotard@st.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Thomas RIENOESSL <thomas.rienoessl@bachmann.info> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-11Revert "dm: pinctrl: Prevent (re-)configuring pins when already done before ↵Lukasz Majewski
relocation" This reverts commit a7f4b4b344396590845e6552c82829ef68ef9f89. As reported by Alex Kiernan the above optimization introduces a regression in the below use case where: 1. Device has defined 'u-boot,dm-spl' property (@ eMMC DTS node) 2. The device downloads its MLO/SPL via UART (not eMMC - the eMMC pinmux pins are NOT probed/configured in MLO/SPL). 3. The loaded via UART MLO/SPL wants to load Linux from eMMC. In this case the DM core and pinctrl uclass checks 'u-boot,dm-spl' and don't configure pins (as it thinks that those were initialized in MLO/SPL). As we are very close to release - please revert this commit. Reported-by: Alex Kiernan <alex.kiernan@gmail.com> Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-01-11ARM: dts: socfpga: Add missing SDMMC resetTien Fong Chee
The SDMMC reset is missing from DT, so the reset manager cannot unreset the SDMMC. Add the missing DT reset entry. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
2019-01-10dm: usb: gadget: Fix boot breakage on sunxi platformsJean-Jacques Hiblot
Fixes commit 013116243950 ("dm: usb: create a new UCLASS ID for USB gadget devices") The UCLASS_DRIVER for id UCLASS_USB_GADGET_GENERIC needs to be declared even for platforms that do not enable DM_USB_GADGET. Otherwise the driver for their usb peripheral controller fails to bind. Reported-by: Priit Laes <plaes@plaes.org> Reported-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Tested-by: Priit Laes <plaes@plaes.org> Acked-by: Jagan Teki <jagan@openedev.com>
2019-01-10usb: Make compiling gadget support optionalJean-Jacques Hiblot
There is no need to compile and include this code if it is not used. CONFIG_USB_GADGET can be used for the purpose. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-01-10Kconfig: rename CONFIG_SPL_USB_GADGET_SUPPORT as CONFIG_SPL_USB_GADGETJean-Jacques Hiblot
The SPL option for USB gadget should be named after the option for u-boot (CONFIG_USB_GADGET) Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-01-10ARM: dts: define USB aliases for all omap5 platformsJean-Jacques Hiblot
This allows us to properly map the USB controller indexes Tested on dra76 evm, am572 evm Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-01-10dm: usb: udc: Use SEQ_ALIAS to index the USB gadget portsJean-Jacques Hiblot
dfu, fastbot and other usb gadget commands take the USB port index as a parameter. Currently this index is assigned in the order of the driver bindings. Changing this behavior using the SEQ_ALIAS feature. This option assign to the device a SEQ number based on its alias (if it exists) To use it we must set the DM_UC_FLAG_SEQ_ALIAS flag and follow the existing naming convention: use "usb" for the name of the gadget UCLASS_DRIVER (same as for the UCLASS_USB). If no alias is provided, then the index falls back to the order in which the bindings took place. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reported-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
2019-01-10Merge branch 'master' of git://git.denx.de/u-boot-sunxiTom Rini
2019-01-10Merge tag 'u-boot-imx-20190110' of git://git.denx.de/u-boot-imxTom Rini
Fixes for 2019.01
2019-01-10mmc: sunxi: Fix mmc clocks for DM_MMCJagan Teki
Existing clock configure code has been followed based on the legacy MMC dt node definitions and it cannot work with recent dts(i) sync from Linux. So, add clock configure code for Allwinner platforms which support DM_MMC and eventually this will drop once CLK support is in Mainline. Fixes: 3c92cca3cda0 ("ARM: dts: sun4i: Update A10 dts(i) files from Linux-v4.18-rc3") Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Priit Laes <plaes@plaes.org> # Gemei G9 A10 Tablet Tested-by: Marek Kraus <gamelasterv2@gmail.com> # A10-OLinuXino-Lime
2019-01-09Merge branch '2019-01-08-master-imports'Tom Rini
- stm32f7 GPIO fixes - SATA env fixes - More DM migration deadline warnings - Regression fix for non-DM MMC drivers - dma_alloc_coherent size fix on ARM.
2019-01-09imx8m: clock: Fix oscillator valuesFabio Estevam
OSC_27M_CLK should return 27MHz and OSC_32K_CLK should return 32768Hz to reflect the reality. This also keeps the values in sync with the Linux clock tree. Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-01-09tools: imx8image: set dcd_skip to truePeng Fan
To B0[+] chips, dcd_skip needs to be true. For A0 chip, it needs to be false, however A0 chip is no longer being supported anymore. Considering we are moving code from imx-mkimage to uboot mkimage, to make sure we not introduce some surprise, we still keep dcd_skip code there. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-09imx8: cpu: correct infoPeng Fan
The CPU banner printed is as following: CPU: CPU: Freescale i.MX8QXP RevB A35 at 147228 MHz 1. Drop the CPU: 2. Change vendor from Freescale to NXP Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-09misc: imx8: scu: use platdata instead of priv dataPeng Fan
priv data has not been allocated when doing bind, so it is wrong to use dev_get_priv in bind call back. Let's switch to use platdata in the driver to fix the issue. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-01-09misc: imx: scu: avoid write null pointerPeng Fan
When boot_dev is true, fill boot device. However the original logic is when boot_dev is false, fill boot device, this will trigger data abort. Also fix sc_misc_get_control when using pointer val. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-09clk: imx8: fix build warningPeng Fan
When build clk driver in spl, met the warning: " drivers/clk/imx/clk-imx8.c:21:25: warning: ‘imx8_clk_names’ defined but not used [-Wunused-variable] static struct imx8_clks imx8_clk_names[] = { ^~~~~~~~~~~~~~ " Fix with wrapping the array with CONFIG_CMD_CLK. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-09MAINTAINERS: update NXP i.MX mail list addressPeng Fan
Update NXP i.MX mail list address Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-01-09board: tbs2910: Remove FIT support in defconfig to reduce u-boot sizeSoeren Moch
The current defconfig build generates a u-boot.imx file that is too large for the available space on a eMMC/SD card. Installing this file overwrites the u-boot environment. So disable the unused FIT support to reduce the size of the u-boot binary. Signed-off-by: Soeren Moch <smoch@web.de>
2019-01-09board: tbs2910: Add u-boot.imx size limit checkSoeren Moch
Check the size of the generated u-boot.imx file. Report an error if it would be too big and overwrite the u-boot environment. Signed-off-by: Soeren Moch <smoch@web.de>
2019-01-09imx: Add Makefile dependency for mkimage_fit_atf.shChris Spencer
The mkimage_fit_atf.sh SPL FIT generator script requires u-boot-nodtb.bin, but this was not enforced by the Makefile. This could cause the generator script to be executed before u-boot-nodtb.bin has been created. Signed-off-by: Chris Spencer <christopher.spencer@sea.co.uk> Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
2019-01-09arm: mx5: Enable WDT and bootcounter on M53MenloMarek Vasut
Enable watchdog and bootcounter support on the M53Menlo board. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2019-01-09ARM: vf610: ddrmc: do not write CR79 by defaultStefan Agner
The current value CTLUPD_AREF(0) is the reset value of the register, so there is no need to write a value. If needed, the register can be written using board specific CR settings. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-01-09ARM: vf610: ddrmc: fix initialization completion detectionStefan Agner
The CR80 register has multiple interrupt bits, the code is supposed to check bit 8 but instead uses a logical and. In most cases this probably did not affect real operations since at that stage typically none of the other bits are set. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-01-09ARM: vf610: ddrmc: fix CR138 preprocessor defineStefan Agner
According to the data sheet bits 10-8 are PHYDRAM_CK_EN. Fix mask to allow setting PHYDRAM_CK_EN correctly. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-01-09toradex: colibri_vf: fix memory initializationStefan Agner
Commit 3f353ceccbbb ("vf610: refactor DDRMC code") changed on-die termination (ODT) values from 120 Ohm to 60 Ohm and enabled a static read/write leveling which has not been tested with this board. This commit reverts both changes and makes sure that memory gets initialized as it has been done before the mentioned commit. Fixes: 3f353ceccbbb ("vf610: refactor DDRMC code") Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-01-09ARM: vf610: ddrmc: program Dummy DDRBYTE1/2Stefan Agner
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter 5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed for correct operation of DDR. Assume the default DDR pin configuration which seems to work well on a Colibri VF50. Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2019-01-09board: toradex: colibri_vf: unset NFS and LOADS/BStefan Agner
Safe some space by not selecting CMD_NFS and CMD_LOADS/B. Signed-off-by: Stefan Agner <stefan.agner@toradex.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-01-09usb: xhci-mem: Fix scratchpad array issueYe Li
After updating the value of dev_context_ptrs[0], we should flush this from cache to memory. Otherwise the xhci controller won't use it. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Marek Vasut <marex@denx.de>
2019-01-09gpio: stm32f7: Fix SPL code sizePatrice Chotard
In order to keep SPL code size below the 32Kb limit, put under CONFIG_SPL_BUILD flag all unused code in SPL. This is needed for stm32f7xx board which are using SPL. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-01-09gpio: stm32f7: Fix gpio bank hole managementPatrice Chotard
In case "gpio-ranges" property is not present in device tree, use default value for gpio_count and gpio_range. This fixes an issue on stm32 F7 and H7 boards where "pinmux status -a" command didn't return any pin status due to the fact that both stm32 F7 and H7 board DT doesn't use the gpio-ranges property. Fixes: dbf928dd2634a6("gpio: stm32f7: Add gpio bank holes management") Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-01-09env: sata: Fix saveenv issueYe Li
Wrong env buffer was passed into sata write function, cause the saveenv not work. Signed-off-by: Ye Li <ye.li@nxp.com>
2019-01-09arm: ti: boot: Remove legacy Android partitionsSam Protsenko
Remove unused Android partitions: - efs, crypto, cache: we don't use it anymore (images are not built in AOSP - ipu1, ipu2: IPU firmware is now a part of vendor image and doesn't reside as a separate partition While at it, rename "reserved" partition to "uboot-env", as it's actually stores U-Boot environment. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
2019-01-09env: sata: Add missed env location for SATA bootYe Li
The env location label ENVL_ESATA is missed in location tables, so when we configure the ENV in SATA, u-boot fails to get correct env location and cause boot hang in board_f. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-01-09arm: Round the dma_alloc_coherent memory size to cache line alignedYe Li
When running usb dwc3 gadget driver, we meet random USB enumeration failure in fastboot. The root cause is a cache coherence issue. When it happens, the ctrl_req in gadget driver is allocated at 0xfe932f40, and the usb_composite_dev (cdev) is allocated at 0xfe932f60. So after we submit the setup request (cache flushed) to USB controller, any accessing to usb_composite_dev variable will cause the cache line refill, then when setup transfer is completed, reading the setup data in ctrl_req will gets old value from cache not from memory. The ctrl_req is allocated by API dma_alloc_coherent, but u-boot don't have cohernet memory. so it still needs cache maintain operations before/after HW accessing. Since the cache flush or invalidate bases on cache line, so when the allocated memory size is not cache line aligned, potentially it may meet such issue. This patch modifies the dma_alloc_coherent API to round the size to cache line aligned. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-29 17:47:34 +0000