Age | Commit message (Collapse) | Author |
|
We have a bunch of boards that define their vendor class identifier and
client archs in the board files or in the distro config. Move everything
to the generic Kconfig options.
We're missing the distinction between i386 and x86_64, as I couldn't find
any config variable that would tell us the difference. Is that really important
to people? I guess not, so I left it out.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Both the dhcp as well as the bootp case add vendor class identifier
parameters into their packets. Let's move that into a separate function
to make overlaying easier.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
We can now successfully boot EFI applications from disk, but users
may want to also run them from a PXE setup.
This patch implements rudimentary network support, allowing a payload
to send and receive network packets.
With this patch, I was able to successfully run grub2 with network
access inside of QEMU's -M xlnx-ep108.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
test/py raises an error, if a board has not enabled bdi command
> pytest.skip('bdinfo command not supported')
E NameError: global name 'pytest' is not defined
import pytest in test/py/u_boot_utils.py fixes this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
This patch fixes a bug that long word(.l) memory access in 'itest'
command reads the 8bytes of the actual memory on 64-bit architecture.
The cast to the memory pointer should use a fixed bit type.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
the last value acceptable value for offset is last_usable_lba + 1
and not last_usable_lba - 1
issue found with SDCARD partition commands on u-boot 2015.10
but this part of code don't change
1- create GPT partion on all the card
> gpt write mmc 0 name=test,start=0,size=0
> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x003a9fde "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: b710eb04-45b9-e94a-8d0b-21458d596f54
=> Start = 0x22*512 = 0x4400
=> Size = (0x003a9fde-0x22+1) * 512 = 0x753F7A00
2- try to recreate the same partition with the next command
(block size:512 bytes = 0x200)
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7A00
Writing GPT: Partitions layout exceds disk size
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7800
Writing GPT: Partitions layout exceds disk size
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7600
Writing GPT: success!
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x003a9fdc "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: 36ec30ef-7ca4-cd48-97cd-ea9fb95185d0
the max LBA when the size is indicated (0x003a9fdc) is lower than
when u-boot compute the max allowed value with size=0 (0x003a9fde)
in the code :
/* partition ending lba */
if ((i == parts - 1) && (partitions[i].size == 0))
/* extend the last partition to maximuim */
gpt_e[i].ending_lba = gpt_h->last_usable_lba;
else
gpt_e[i].ending_lba = cpu_to_le64(offset - 1);
so offset = gpt_h->last_usable_lba + 1 is acceptable !
but the test (offset >= last_usable_lba) cause the error
END
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>disk: part_efi: fix check of the max partition size
the last value acceptable value for offset is (last_usable_lba + 1)
and not (last_usable_lba - 1)
issue found with SDCARD partition commands on u-boot 2015.10
but this part of code don't change
1- I create GPT partion on all the card (start and size undefined)
> gpt write mmc 0 name=test,start=0,size=0
> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x003a9fde "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: b710eb04-45b9-e94a-8d0b-21458d596f54
=> Start = 0x22*512 = 0x4400
=> Size = (0x003a9fde-0x22+1) * 512 = 0x753F7A00
2- I try to recreate the same partition with the command gpt write
and with start and size values (block size:512 bytes = 0x200)
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7A00
Writing GPT: Partitions layout exceds disk size
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7800
Writing GPT: Partitions layout exceds disk size
> gpt write mmc 0 name=test,start=0x4400,size=0x753F7600
Writing GPT: success!
I check the partition created :
> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x003a9fdc "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: 36ec30ef-7ca4-cd48-97cd-ea9fb95185d0
=> but the max LBA when the size is indicated (0x003a9fdc) is lower than
when u-boot compute the max allowed value with size=0 (0x003a9fde)
3- in the code, just after my patch, line 446
/* partition ending lba */
if ((i == parts - 1) && (partitions[i].size == 0))
/* extend the last partition to maximuim */
gpt_e[i].ending_lba = gpt_h->last_usable_lba;
else
gpt_e[i].ending_lba = cpu_to_le64(offset - 1);
so offset = gpt_h->last_usable_lba + 1 is acceptable !
(it the value used when size is 0)
but today the test (offset >= last_usable_lba) cause the error
my patch only solve this issue
END
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
|
|
If serial support is not compiled into U-Boot, which may be the case
for some SPL builds, the following warning will be generated in disk.c:
cmd/disk.c: In function 'common_diskboot':
cmd/disk.c:16:6: warning: variable 'dev' set but not used [-Wunused-but-set-variable]
int dev, part;
^
The warning is a result of printf() calls being optimized away, and
thus the whole dev variable becomes indeed unused. Mark the variable
as __maybe_unused .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
If bl_len is not aligned it can caused a problem because another code
expects that start is aligned.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
A DM driver for PCA953x was recently introduced by Peng Fan, which lacked
support for the 40 GPIO versions.
This patch adds support for these chips.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
for double buffering to work, redundant buffers must have equal size
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
|
|
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
|
|
checkpatch complains about in succeding patch. Prefer to fix all
declarations in a dedicated patch.
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
|
|
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
|
|
|
|
GCC 5.3 report a warning: 'upper' and 'lower' may be used
uninitialized in this function [-Wmaybe-uninitialized].
Compiler might need explicit initializer.
Signed-off-by: Wills Wang <wills.wang@live.com>
|
|
We need reset the Ethernet Switch analog part before operation,
or the build-in Ethernet PHY don't work.
Signed-off-by: Wills Wang <wills.wang@live.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Remove the remnants of JZ4740 support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
|
|
Certain chips, like the JZ47xx, have extreme size constraints on the
SPL size and require custom start.S . Allow overriding the start.S
the same way ARM MXS does it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
|
|
Move CONFIG_SYS_TEXT_BASE to Kconfig, and add default values in board
Kconfig files matching what was present in their config headers. This
will make it cleaner to conditionalise the value for Malta based on 32
vs 64 bit builds.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
|
|
Make use of device model & device tree to probe the UART driver. This is
the initial step in bringing Malta up to date with driver model, and
allows for cleaner handling of the different I/O addresses for different
system controllers by specifying the ISA bus address instead of a
translated memory address.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
The address of the UART differs based upon the system controller because
it's actually within the I/O port region, which is in a different
location for each system controller. Rather than handling this as 2
UARTs with the correct one selected at runtime, use I/O port accessors
for the UART such that access to it gets translated into the I/O port
region automatically.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
If the UART is to be accessed using I/O port accessors (inb & outb) then
using map_physmem doesn't make sense, since it operates in a different
memory space. Remove the call to map_physmem when
CONFIG_SYS_NS16550_PORT_MAPPED is defined, allowing I/O port addresses
to not be mangled by the incorrect mapping.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Provide some documentation for the fields of struct of_bus, for
consistency with that provided for the new match field.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Support ISA busses in much the same way as Linux does. This allows for
ISA bus addresses to be translated, and only if CONFIG_OF_ISA_BUS is
selected in order to avoid including the code in builds which won't need
it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The arm64 Linux boot protocol [1] describes the fields in the Image
header as being 64-bit little endian values.
So fix the endianess conversion to use 64-bit sized operations, for
both image_size and text_offset.
Also we use a local variable for the image_size to avoid both writing
to the header and also accessing it after we actually unmapped it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[1] https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/Documentation/arm64/booting.txt
|
|
|
|
|
|
Sets LDO3 and LDO4 regulators at 2.8V. In the current config
these are off. This causes kernel to hang during
axp209 initialization.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.
Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The originally committed .dts files for the Pine64 were from an early
proof-of-concept version and should have never been committed upstream.
Replace them with much more mature versions, which also use a different
naming scheme.
Please note that at this point there is at least one binding which has
not been agreed upon, so this is subject to change.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
As arm64 has slightly different expectations about load addresses, lets
use a different set of default addresses for things like the kernel.
As arm64 kernels don't come with a decompressor right now, reserve some
more space for really big uncompressed kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The ARM Trusted Firmware (ATF) code now lives in SRAM on the Pine64/A64,
so we can claim the whole of DRAM for OS use.
This reverts commit 3ffe39ed2b66af71c7271d0cef2a248b5bf7dfdb.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This addresses a cosmetic issue when booting a sunxi device
over USB (FEL mode), where the SPL currently would just print
"Trying to boot from ". The patch fixes that to properly read
"Trying to boot from FEL".
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The current SPL header, created by the 'mksunxiboot' tool, has size
32 bytes. But the code in the boot ROM stores the information about
the boot media at the offset 0x28 before passing control to the SPL.
For example, when booting from the SD card, the magic number written
by the boot ROM is 0. And when booting from the SPI flash, the magic
number is 3. NAND and eMMC probably have their own special magic
numbers too.
Currently the corrupted byte is a part of one of the instructions in
the reset vectors table:
b reset
ldr pc, _undefined_instruction
ldr pc, _software_interrupt <- Corruption happens here
ldr pc, _prefetch_abort
ldr pc, _data_abort
ldr pc, _not_used
ldr pc, _irq
ldr pc, _fiq
In practice this does not cause any visible problems, but it's still
better to fix it. As a bonus, the reported boot media type can be
later used in the 'spl_boot_device' function, but this is out of
the scope of this patch.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The A80 uses the AXP809 as its primary PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Adds poweroff support for axp818 pmic.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The SW output of the PMIC supplies the ethernet PHY with power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The AXP818 has a switchable output, SW. This is commonly used for
controlling power to the LCD backlight.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Description said eldo2 instead of fldo2, a copy-paste error.
Fixes: 38491d9c6515 ("power: axp818: Add support for FLDOs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The ELDO enable bits and registers are contiguous for axp221. Instead
of a switch case testing against the index, just use the index to shift
the bit or register offset.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The newer chips use a newer display pipeline, which is not supported.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
A83T, H3, and A64 have a dedicated pin for card detect on the PF
pingroup. This is used in all designs. Set it as the default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
In most other places, we sort SoC descriptions by family (sunXi) first,
then by the chip name (A20).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The user should always select an SoC variant to support. Not choosing
one doesn't make sense for a bootloader.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Make the USB feature really available.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This is a low-cost ARMv8 SoC from Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Correct some register names.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This header will be shared between PH1-LD11 and PH1-LD20
(and hopefully new ARMv8 SoCs developed in the future),
so umc64-regs.h would be a better fit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Tidy up alignment of open parentheses.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|