summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-05-05imx: mx53ard: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: ima3-mx53: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: iomux-v3: Add iomux-mx53.hBenoît Thébaudeau
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for the i.MX53. The content of the file is taken from Freescale's Linux kernel at commit 4ab3715, plus the required changes to make it work in U-Boot. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: vision2: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, except for older silicon revisions for which support is removed. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx51_efikamx/sb: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, except for older silicon revisions for which support is removed. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Tested-by: Matt Sealey <matt@genesi-usa.com>
2013-05-05imx: mx51evk: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, except for older silicon revisions for which support is removed. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: iomux-v3: Add missing definitions to iomux-mx51.hBenoît Thébaudeau
Add missing definitions that are required by future changes. By the way, make some cosmetic cleanup. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: iomux-mx51: Fix MX51_PAD_EIM_CS2__GPIO2_27Benoît Thébaudeau
In ALT1 mode, EIM_CS2 is GPIO2[27], not ESDHC1.CD. Hence, rename MX51_PAD_EIM_CS2__SD1_CD to MX51_PAD_EIM_CS2__GPIO2_27. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx35: Remove legacy iomux supportBenoît Thébaudeau
Legacy iomux support is no longer needed now that all boards have been converted to iomux-v3. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: woodburn: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx35pdk: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx35pdk: Fix WDOG_RST iomux functionBenoît Thébaudeau
The signal connected from this pin to the PMIC is WDOG_B, i.e. ALT0 mode, not ALT1 (which even corresponds to nothing). Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: flea3: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: iomux-v3: Add iomux-mx35.hBenoît Thébaudeau
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for the i.MX35. The content of the file is taken from Linux kernel at commit 267dd34, plus the required changes to make it work in U-Boot. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx25: Remove legacy iomux supportBenoît Thébaudeau
Legacy iomux support is no longer needed now that all boards have been converted to iomux-v3. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: zmx25: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: tx25: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx25pdk: Fix GPIO assignmentsBenoît Thébaudeau
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: mx25pdk: Convert to iomux-v3Benoît Thébaudeau
There is no change of behavior, even if some pad control values could probably be simplified. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05imx: iomux-v3: Add iomux-mx25.hBenoît Thébaudeau
Allow usage of the imx-common/iomux-v3.h framework by including pad settings for the i.MX25. The content of the file is taken from Linux kernel at commit 267dd34, plus the required changes to make it work in U-Boot. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05arm: mx5: Add support for DENX M53EVKMarek Vasut
Add basic support for the DENX M53EVK board. Currently supported is: MMC (incl. booting) NAND (incl. booting) Ethernet, I2C, USB, SATA, RTC. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Wolfgang Denk <wd@denx.de>
2013-05-05arm: mx5: Add NAND clock handlingMarek Vasut
Augment the MX5 clock code with function to enable and configure NFC clock. This is necessary to get NFC working on MX5. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
2013-05-05arm: mx5: Add SPL support code to MX5Marek Vasut
Fix minor adjustments needed to get SPL framework building on MX5. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
2013-05-05arm: imx: Pack u-boot.bin into uImage for SPLMarek Vasut
The U-Boot SPL can parse the uImage format and gather information from it about the payload. Make use of this and wrap u-boot.bin into uImage format. The benefit is the SPL will know the size of the payload instead of using fixed size of the payload defined at compile time. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
2013-05-05nand: Add SPL_NAND support to mxc_nand_splMarek Vasut
Add support for generic NAND SPL via the SPL framework into the mxc_nand_spl driver. This is basically just a simple rename and publication of the already implemented functions. To avoid the bare-bones functions getting in the way of the NAND_SPL, build them only if CONFIG_SPL_FRAMEWORK is not defined. Also make sure the requested payload is aligned to full pages, otherwise this simple driver fails to load the last page. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com> Acked-by: Scott Wood <scottwood@freescale.com>
2013-05-05imx: Align the imximage header and payload to multiples of 4kMarek Vasut
The MX53 ROM loads the data from NAND in multiples of pages and supports maximum page size of 4k. Thus, align the image and header to 4k to be safe from ROM bugs. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@ti.com>
2013-05-05mxs: spl_mem_init: Change EMI port priorityFabio Estevam
FSL bootlets code set the PORT_PRIORITY_ORDER field of register HW_EMI_CTRL as 0x2, which means: PORT0231 = 0x02 Priority Order: AXI0, AHB2, AHB3, AHB1 Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05mxs: spl_mem_init: Skip the initialization of some DRAM_CTL registersFabio Estevam
HW_DRAM_CTL27, HW_DRAM_CTL28 and HW_DRAM_CTL35 are not initialized as per FSL bootlets code. mx23 Reference Manual mark HW_DRAM_CTL27 and HW_DRAM_CTL28 as "reserved". HW_DRAM_CTL8 is setup as the last element. So skip the initialization of these DRAM_CTL registers. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05mxs: spl_mem_init: Remove erroneous DDR settingFabio Estevam
On mx23 there is no 'DRAM init complete' in register HW_DRAM_CTL18. Remove this erroneous setting. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05mxs: spl_mem_init: Fix comment about start bitFabio Estevam
Start bit is part of HW_DRAM_CTL8 register, so fix the comment. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05mx23_olinuxino: Fix DDR pin iomux settingsFabio Estevam
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from Freescale, which results in much better stability. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05mx23evk: Fix DDR pin iomux settingsFabio Estevam
Change MUX_CONFIG_EMI to use the same drive strength as the bootlets code from Freescale, which results in much better stability. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-05-05mx23: Fix pad voltage selection bitFabio Estevam
On mx23 the pad voltage selection bit needs to be always '0', since '1' is a reserved value. For example: Pin 108, EMI_A06 pin voltage selection: 0= 1.8V (mDDR) or 2.5V (DDR1); 1= reserved. Fix the pad voltage definitions for the mx23 case. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
2013-05-03P1022DS: Set CONFIG_SPL_MAX_SIZE directlyTom Rini
With the u-boot-with-spl.bin rule calling $(OBJCOPY) with CONFIG_SPL_PAD_TO, and CONFIG_SPL_PAD_TO defaulting to CONFIG_SPL_MAX_SIZE we cannot use math here, so set it to 4096 rather than 4 * 1024. Signed-off-by: Tom Rini <trini@ti.com>
2013-05-02Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini
2013-05-02powerpc/85xx: set USB2 default mode to 'device' for (super)hydra boardsShaohui Xie
The Hydra and Superhydra (P3041DS, P5020DS, and P5040DS) boards have a second USB port that can be configured in either host, peripheral (aka device), or OTG (on-the-go) mode. When configured in host mode, if the port is connected to another USB host, damage to the board can occur. To avoid this, we change the default setting to peripheral mode. Ideally, we'd set it to OTG mode, but currently there is no OTG support for these boards. Setting the hwconfig variable will also update the device tree, and so Linux will configure the port for peripheral mode as well. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Timur Tabi <timur@tabi.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/p1_p2_rdb_pc: Add a pin to reset the DDR chip for P1021RDB-PCXu Jiucheng
When P1021RDB-PC reboot system, the board will hung at uboot DDR configuration. For P1021RDB-PC DDR reset pin is multiplex with QE, so uboot will reserve this pin for QE and skip DDR reset. Other platforms without QE will do this reset. This patch adds a slight code to reset DDR chip by QE CE_PB8 pin for NAND and NOR FLASH boot. For booting from SPI FALSH and SD card, it seems possible to use the rom on chip to write to the GPIO pins before configuring the DDR. Signed-off-by: Xu Jiucheng <B37781@freescale.com> Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/mpc85xx: Changed LIODN offset valuesCristian Sovaiala
Extending LIODN offset range from 1-5 to 1-10 While using a qman portal with a higher index the LIODN offset is incorrectly set, thus extending the range of offsets covers all 10 qman portals Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com> Acked-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/mpc85xx: Extend workaround for erratum DDR_A003 to other SoCsYork Sun
Erratum DDR_A003 applies to P5020, P3041, P4080, P3060, P2041, P5040. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/p1010rdb: add readme document for p1010rdbShengzhou Liu
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/p1010rdb: Change flexcan compatible stringShengzhou Liu
Change flexcan compatible string from "fsl,flexcan-v1.0" to "fsl,p1010-flexcan" to match the device tree. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/85xx: add SerDes bank 4 lanesTimur Tabi
Only some chips have four SerDes banks, so don't define lanes for a bank that doesn't exist. Signed-off-by: Timur Tabi <timur@tabi.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02qoriq/p1_p2_rdb_pc: USB device-tree fixups for P1020Zhicheng Fan
Resolve P1020 second USB controller multiplexing with eLBC - mandatory to mention USB2 in hwconfig string to select it over eLBC, otherwise USB2 node is removed - works only for SPI and SD boot Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Zhicheng Fan <B32736@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02doc/ramboot.mpc85xx: Documented the RAMBOOT for MPC85xxPoonam Aggrwal
There could be scenarios where the user would like to manually(via JTAG) configure the DDR/L2SRAM and load the bootloader binary onto DDR/L2SRAM. This document explains thse usecases and the detailed explanation of what needs to be done to use it. Most of the code from CONFIG_SYS_RAMBOOT will be used except for small changes of CCSRBAR etc. The changes are not very large, but it is good to document them so that user can get it working at once. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/mpc85xx:IFC Errata A003399 is not valid for BSC913xPrabhakar Kushwaha
As per Errata list of BSC9131 and BSC9132, IFC Errata A003399 is no more valid. So donot compile its workaround. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02mpc85xx: Fix a compiler warning when CONFIG_WATCHDOG is turned onHorst Kronstorfer
cpu.c:288:2: warning: implicit declaration of function 'reset_85xx_watchdog' [-Wimplicit-function-declaration] Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/85xx: Add workaround for errata USB-14 (enable on P204x/P3041/P50x0)Xulei
On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal multi-bit ECC errors, which has impact on performance, so software should disable all ECC reporting from USB1 and USB2. In formal release document, the errata number should be USB14 instead of USB138. Signed-off-by: xulei <Lei.Xu@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: xulei <B33228@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/b4860qds: Add the tlb entries for SRIO interfacesLiu Gang
Add the tlb entries based on the configuration of the SRIO interfaces. Every SRIO interface has 256M space: #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02fman/mEMAC: set SETSP bit in IF_MODE regisgter for RGMII speedZang Roy-R61911
Some legacy RGMII phys don't have in band signaling for the speed information. so set the RGMII MAC mode according to the speed got from PHY. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Reported-by: John Traill <john.traill@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02powerpc/mpc85xx: set clock-frequency for T4/B4 clockgen nodeTang Yuantian
For T4/B4, the clockgen node compatible string is updated to version 2. Add clock-frequency setting for this new version. Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
generated by cgit (git 2.34.1) at 2025-01-18 18:25:04 +0000