| Age | Commit message (Collapse) | Author |
|---|
|
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF
for NAND specific warning removal, same is done in this patch
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
The TRAB board references local libgcc helper routines
(lib_arm/div0.o and lib_arm/_umodsi3.o) which cause build problems
when we try to use the normal, compiler provided libgcc instead.
Removing these references allows to build both with and without the
local libgcc helper routines.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Commit f62fb99941c6 fixed handling of all rodata sections by using a
wildcard combined with calls to ld's builtin functions SORT_BY_ALIGNMENT()
and SORT_BY_NAME(). Unfortunately these functions were only
introduced with biunutils version 2.16, so the modification broke
building with all tool chains using older binutils.
This patch makes it work again. This is done by omitting the use of
these functions for such old tool chains. This will result in
slightly larger target binaries, as the rodata sections are no longer
in optimal order alignment-wise which reauls in unused gaps, but the
effect was found to be insignificant - especially compared to the fact
that you cannot build U-Boot at all in the current state.
As ld seems to have no support for conditionals we run the linker
script through the C preprocessor which can be easily used to remove
the unwanted function calls.
Note that the C preprocessor must be run with the "-ansi" (or a
"-std=") option to make sure all the system-specific predefined
macros outside the reserved namespace are suppressed. Otherise, cpp
might for example substitute "powerpc" to "1", thus corrupting for
example "OUTPUT_ARCH(powerpc)" etc.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
|
|
For some time there have been repeated reports about build problems
with some ARM (cross) tool chains. Especially issues about
(in)compatibility with the tool chain provided runtime support
library libgcc.a caused to add and support a private implementation
of such runtime support code in U-Boot. A closer look at the code
indicated that some of these issues are actually home-made. This
patch attempts to clean up some of the most obvious problems and make
building of U-Boot with different tool chains easier:
- Even though all ARM systems basicy used the same compiler options
to select a specific ABI from the tool chain, the code for this was
distributed over all cpu/*/config.mk files. We move this one level
up into lib_arm/config.mk instead.
- So far, we only checked if "-mapcs-32" was supported by the tool
chain; if yes, this was used, if not, "-mabi=apcs-gnu" was
selected, no matter if the tool chain actually understood this
option. There was no support for EABI conformant tool chains.
This patch implements the following logic:
1) If the tool chain supports
"-mabi=aapcs-linux -mno-thumb-interwork"
we use these options (EABI conformant tool chain).
2) Otherwise, we check first if
"-mapcs-32"
is supported, and then check for
"-mabi=apcs-gnu"
If one test succeeds, we use the first found option.
3) In case 2), we also test if "-mno-thumb-interwork", and use
this if the test succeeds. [For "-mabi=aapcs-linux" we set
"-mno-thumb-interwork" mandatorily.]
This way we use a similar logic for the compile options as the
Linux kernel does.
- Some EABI conformant tool chains cause external references to
utility functions like raise(); such functions are provided in the
new file lib_arm/eabi_compat.c
Note that lib_arm/config.mk gets parsed several times, so we must
make sure to add eabi_compat.o only once to the linker list.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Dirk Behme <dirk.behme@googlemail.com>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Sergey Kubushyn <ksi@koi8.net>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
Tested-by: Andrzej Wolski <awolski@poczta.fm>
Tested-by: Gaye Abdoulaye Walsimou <walsimou@walsimou.com>
Tested-by: Tom Rix <Tom.Rix@windriver.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
|
|
|
|
|
|
The code copy data from NAND flash block by block, so when
the data length isn't a whole-number multiple of the block
size, it will overlap the rest space.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Signed-off-by: giulio.benetti@micronovasrl.com
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
Previously, waiting for auto-negotiation would only occur if a valid
link had been detected. Problems arose when attempting to use a
tsec immediately after bootup but before link was achieved, eg:
=> dhcp
Auto-neg error, defaulting to 10BT/HD
eTSEC1: No link.
Auto-neg error, defaulting to 10BT/HD
eTSEC2: No link.
=>
With this patch applied the same operation as above resulted in:
=> dhcp
Waiting for PHY auto negotiation to complete. done
Enet starting in 1000BT/FD
Speed: 1000, full duplex
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
U-boot might use non-8-byte-aligned addresses for sending data, which
the kwgbe_send doesn't accept (bootp does this for me). This patch
copies the data to be sent to a malloced temporary buffer if it is
non-aligned.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
This patch makes the device wait for up to 5 seconds for the link to
come up, similar to what many of the other network drivers do. This
avoids confusing situations where, e.g., a tftp fails when initiated
early after U-boot has started (before the link has come up).
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
The Intel E1000 driver was making assumptions about the relationship between
some virtual, physical, and PCI addresses.
Also fix some bad usage of the DEBUGOUT macro
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
We should call jffs2_clean_cache() if we return from jffs2_build_lists()
with an error to prevent usage of incomplete lists. Also we should
free() a local buffer to prevent memory leaks.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
|
|
|
|
The name of the atmel nand driver in the kernel changed from at91_nand
to atmel_nand back in June 2008, but the at91-based boards config files
still refer to at91_nand. This patch updates them with the new name
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
|
|
In commit 187af954cf7958c24efcf0fd62289bbdb4f1f24e there
was a typo that offset all the ecc registers by 4 bytes, fixed that.
Signed-off-by: Ben Goska <goskab@onid.oregonstate.edu>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
This patch fixes the "chip_config" command for I2C bootstrap EEPROM
configuration. First it changes the I2C bootstrap EEPROM address to
0x54 as this is used on Arches (instead of 0x52 on Canyonlands/
Glacier). Additionally, the NAND bootstrap settings are removed
for Arches since Arches doesn't support NAND-booting.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Current code for the Monahans CPU defined OSCR_CLK_FREQ as 3.250 (MHz)
which caused floating point operations to be used. This resulted in
unresolved references to some FP related libgcc functions when using
U-Boot's private libgcc functions.
Change the code to use fixed point math only.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
When we init the addrmap based on the TLB we will not end up getting
the TLB that covers memory if we are using SPD. The reason is we
haven't relocated at the point that we setup the memory TLB and thus it
will not get setup in the addrmap.
Instead we can just walk over the TLB array after we've relocated and
see all the TLBs that have been set and use that information to populate
the initial addrmap. By doing this we insure that we get the TLB
entries that cover memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Fix bug introduced by 9c048b523413ae5f3ff34e00cf57569c3368ab51.
The cfi_flash.c driver cast the flash buffer size to a uchar in
flash_write_cfibuffer(). On some flash parts, (tested on Numonyx
part PC32F512M29EWH), the buffer size is 1KB. Remove the cast to
uchar to enable buffer sizes to be larger.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The local board-specific spi_init() function conflicts with the common SPI
layer, so rename it to something board-specific.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
This patch adds watchdog reset call to allow its invokation during decompression
phase. This control was present on old zlib version and here it is
backported for those relevant routines. This patch is sent as a zlib separate
one beacuse it was not tested due to specific board lack.
zlib patches will be unified just in one when this will be validated through
tests.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
|
|
This patch updates zlib to the latest stable version.
Only relevant zlib parts were ported to u-boot tree, as already did for the
current zlib (0.95). New zlib guarantees a faster inflate performances
other then others improvements as explained at www.zlib.net.
It also includes Alessandro Rubini's patches to allow 0 as destination pointer
and to call watchdog reset if required by architecture.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Reviewed-by: Angelo Castello <angelo.castello@st.com>
Reviewed-by: Alessandro Rubini <rubini-list@gnudd.com>
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
|
|
|
|
|
|
The initial pixclock for the MIMC200 board is wrong (and causes
screen corruption due to DMA underruns).
This patch simply reduces the pixel clock to fix the problem.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
|
|
Fixed a misunderstanding in the original implementation, 'devnum' that
was used in the cpu/ppc4xx/4xx_enet.c implementation was NOT the
PHY's SMI address, rather it was the number of the MAC interface on
the CPU. The equivalent of this for uec_phy will be the UEC number
stored in mii_info->dev->name. Usage example is updated for uec.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
It is set to 0x1F by default and can be overwritten on the board
header file by defining CONFIG_UTBIPAR_INIT_TBIPA. This allows
the CPU to simply "reserve" one SMI address instead of using
a different one for each UEC.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
eth_setenv_enetaddr is avaible by upper layer
using this saves 204 bytes on total image size
used Local OUI instead of Marvell OUI for
random MAC address generation logic
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Fix E1000 build warning on AP1000 board
Fix the build warning on AP1000 board:
e1000.c:131: warning: 'e1000_read_eeprom' used but never defined
e1000.c:2012: warning: 'e1000_set_phy_mode' defined but not used
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Due to recent changes to the NET support on U-boot, DM9000
is no longer detected on the DM355 EVM.
This minor update enables DM9000 on the DM355 EVM.
Tested on the DM355 EVM
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
1. mv88E61xx driver compiler warnings fixed
2. idstr if-else statements changed to switch() construct
and added default case too.
This fixed idstr may be uninitialized warning
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
This patch adds an FTMAC100 ethernet driver for Faraday A320 evaluation board.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
For some reason the MPC8544 enabled BEDBUG if PCI was enabled and that
got copied int the MPC8536, MPC8572 and P2020 DS boards. The BEDBUG
support has never been made to work completely on e500/85xx so we
just disable it to save space and match the other FSL 85xx boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
tftp.c:294: warning: pointer targets in passing argument 1 of 'strlen'
differ in signedness
This was only visible for the utx8245 board which seems to have DEBUG
enabled.
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Remove bogus config.mk entry, fix newline and remove redundant
omap3/config.mk
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
Applying two indepenent OMAP3 patches resulted in missing
GPMC_CONFIG_CS0_BASE. Patch "omap3: embedd gpmc_cs into gpmc
config struct" removes GPMC_CONFIG_CS0_BASE, independent patch
"omap3: bug fix for NOR boot support" introduces it's usage.
Re-introduce GPMC_CONFIG_CS0_BASE.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
|
|
This is a port of Linux driver for SDHC host controller hardware
found on Freescale's MX2 and MX3 processors. Uses new generic MMC
framework (CONFIG_GENERIC_MMC) and it looks like there are some
problems with a framework (at least on LE cpus). Some of these
problems are addressed in the following patches.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
|
|
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
|
|
This chip is used in a number of boards manufactured by Calao-Systems
which should be supported soon. This driver provides the necessary
spi_read and spi_write functions necessary to communicate with the chip.
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
|
|
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF
for NAND specific warning removal, same is done in this patch
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
|
|
It was brought to our attention that U-Boot contains code derived from the
IBM OpenBIOS source code originally provided with some of the older PowerPC
4xx development boards. As a result, the original license of this code has
been carried in the various files for a number of years in the U-Boot project.
IBM is dual-licensing the IBM code contributions already present in U-Boot
under either the terms of the GNU General Public License version 2, or the
original code license already present.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
