summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-12-03ARM: dts: rmobile: Enable SDR104 on Salvator-X and ULCBMarek Vasut
Enable SDR104 modes on M3W and H3 boards. With the SDHI fixes in place, it is now possible to use SDR104. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-03ARM: dts: rmobile: Add eMMC DS pinmuxMarek Vasut
Add pinmux entry for the eMMC DS line, as it is connected on these boards. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-03mmc: tmio: sdhi: Add HS400 supportMarek Vasut
Add support for the HS400 mode to SDHI driver. This uses the up-tune mechanism from already supported HS200 tuning. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-03mmc: tmio: sdhi: Move tap_pos to private dataMarek Vasut
Move the tap_pos variable, which is the HS200/HS400/SDR104 calibration offset, into private data, so it can be passed around. This is done in preparation for the HS400 mode, which needs to adjust this value. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-03mmc: tmio: sdhi: Filter out HS400 on certain SoCsMarek Vasut
Filter out HS400 support on SoCs where HS400 is not supported yet. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-03mmc: tmio: Reorder TMIO clock handlingMarek Vasut
Reorder the tmio_sd_set_clk_rate() function such that it handles all of the clock requiests correctly. Specifically, before this patch, clock request with (mmc->clock == 0 && mmc->clk_disable) could leave the clock enabled, as the function would exit on if (!mmc->clock) condition on top and will not handle the mmc->clk_disable at all. Rather than band-aid fixing just that particular problem, reorder the entire function to make it easier to understand and verify that all the cases are covered. The function has three sections now: First, if mmc->clock != 0, we calculate divider for the SD block. Second, if mmc->clock != 0 and SD block clock are enabled and current divider is not equal to the new divider, then stop the clock and update the divider. Third, if mmc->clk_disable is set, disable the clock, otherwise enable the clock. This happens independently of divider update now. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-03mmc: tmio: Keep generating clock when clock are enabledMarek Vasut
The TMIO core has a feature where it can automatically disable clock output when the bus is not in use. While this is useful, it also interferes with switching the bus to 1.8V and other background tasks of the SD/MMC cards, which require clock to be enabled. This patch respects the mmc->clk_disable and only disables the clock when the MMC core requests it. Otherwise the clock are continuously generated on the bus. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-03mmc: tmio: Do not set divider to 1 in DDR modeMarek Vasut
The TMIO core has a quirk where divider == 1 must not be set in DDR modes. Handle this by setting divider to 2, as suggested in the documentation. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-12-03mmc: tmio: Switch to clock frameworkMarek Vasut
Switch the driver to using clk_get_rate()/clk_set_rate() instead of caching the mclk frequency in it's private data. This is required on the SDHI variant of the controller, where the upstream mclk need to be adjusted when using UHS modes. Platforms which do not support clock framework or do not support it in eg. SPL default to 100 MHz clock. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> --- V2: - Fix build on certain platforms using SPL without clock framework V3: - Turn clk_get_rate into a callback and fill it as needed on both renesas and socionext platforms
2018-12-03mmc: Parse HS400 DT propertiesMarek Vasut
Add HS400 properties parsing support to mmc_of_parse(). Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Jean-Jacques Hiblot <jjhiblot@ti.com> Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org>
2018-12-03clk: renesas: Allow reconfiguring SDHI clock on Gen3Marek Vasut
The SDHI clock must be configured differently for HS200/HS400/SDR104 modes. Add support for reconfiguring the SDHI clock settings into the clock driver. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-12-03arc: devboards: Implement checkboard()Alexey Brodkin
This allows us to print nice board name on boot. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-12-03arc: emsdp: Refactor register and bit accessesAlexey Brodkin
Instead of "base + offset" define all registers right away and access them later via direct defines. Generate bit masks with "BIT" macro. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-12-03arc: emsdp: Read real CPU clock value from hardwareAlexey Brodkin
We do real CPU clock measurement with help of built-in counters. Thus we may accommodate different real clock values that appear in different FPA images instead of relying on something hard-coded in the .dtb. And while at it make make SDIO base address define look similar to others with casting to "(void *)". Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-12-03arc: Get rid of board-specific print_cpuinfo()Alexey Brodkin
Since we now do advanced CPU identification in generic ARC code there's no need to have per-board hardcoded data. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-12-03ARC: Improve identification of ARC coresAlexey Brodkin
1. Try to guess a ARC core template that was used i.e. not just name a core family but something more menaingful like "ARC HS38", "ARC EM11D" etc. We do it checking availability of the key differentiation features like: - Caches (we actually only check for L1 I$ fpr simplicity) - XY-memory - DSP extensions etc. 2. Identify ARC subsystems 3. Print core clock frequency Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-12-03arc: emsdp: Bump RAM size to 16 MbAlexey Brodkin
On v2 boards that will hit real stock we'll have 16 Mb of RAM. Note on v1 boards (if anybody ever get one out of trash bin) this leads to U-Boot execution freeze in the middle ofthe relocation so don't be surprised. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2018-12-03efi_loader: bootmgr: add load option helper functionsAKASHI Takahiro
In this patch, helper functions for an load option variable (BootXXXX) are added: * efi_deserialize_load_option(): parse a string into load_option data (renamed from parse_load_option and exported) * efi_serialize_load_option(): convert load_option data into a string Those functions will be used to implement efishell command. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-03efi_loader: allow device == NULL in efi_dp_from_name()AKASHI Takahiro
This is a preparatory patch for use in efi_serialize_load_option() as a load option's file_path should have both a device path and a file path. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02ARM: rpi_*_defconfig: Add support to find UUID for filesystemOtavio Salvador
The most generic way of having a stable boot behavior is to rely on UUID instead of device names for root partition, so the order of probing does not cause issues with booting. This enables the `CMD_FS_UUID` for following defconfig files: - rpi_0_w_defconfig - rpi_2_defconfig - rpi_3_32b_defconfig - rpi_3_defconfig - rpi_defconfig Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02rpi: Add mmc 1 as a boot targetEmmanuel Vadot
When booting with the rpi-firmware "mmc" overlay that disable the SDHOST controller and use the SDHCI one for the sd card, mmc 1 because a viable boot target. Add it to the list Signed-off-by: Oleksandr Tymoshenko <gonzo@FreeBSD.org> Signed-off-by: Emmanuel Vadot <manu@freebsd.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02doc: README.iscsi: Open-iSCSI configurationHeinrich Schuchardt
Provide settings for Open-iSCSI Reformat headers. h3-headers marked with ^^^ are not recognized in some markup editors. Use the ### notation instead. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: Align runtime section to 64kbAlexander Graf
The UEFI spec mandates that runtime sections are 64kb aligned to enable support for 64kb page size OSs. This patch ensures that we extend the runtime section to 64kb to be spec compliant. Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_selftest: rename setup_okHeinrich Schuchardt
The variable name setup_ok might suggest a boolean with true indicating OK. Let's avoid the misleading name. %s/setup_ok/setup_status/g Suggested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: fix simple network protocolHeinrich Schuchardt
We should not call eth_rx() before the network interface is initialized. The services of the simple network protocol should check the state of the network adapter. Add and correct comments. Without this patch i.mx6 system Wandboard Quad rev B1 fails to execute bootefi selftest. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: correctly aligned transmit bufferHeinrich Schuchardt
Calling net_send_packet() requires that the buffer is aligned to a multiple of PKTALIGN (= ARCH_DMA_MINALIGN). The UEFI spec does not require efi_net_transmit() to be called with a buffer with any special alignment. So we have to copy to an aligned buffer. The current coding copies to an aligned buffer only if CONFIG_EFI_LOADER_BOUNCE_BUFFER=y. Many boards like the Odroid C2 do not use a bounce buffer. With the patch we copy to a correctly aligned buffer in all cases. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_selftest: fix simple network protocol testHeinrich Schuchardt
To use the simple network protocol we have to call the start service first and the initialize service second. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02MAINTAINERS: add EFI PAYLOAD reviewerHeinrich Schuchardt
Alex suggested to add me as a reviewer for the EFI subsystem. The patch also adds a description for R: entries. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_selftest: check fdt is marked as runtime dataHeinrich Schuchardt
Check that the memory area containing the device tree is marked as runtime data. Update the Python test to pass ${fdtcontroladdr} to bootefi. Update the description of the Python test. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: create fdt reservation before copyHeinrich Schuchardt
When copying the device we must ensure that the copy does not fall into a memory area reserved by the same. So let's change the sequence: first create memory reservations and then copy the device tree. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: fix memory mapping for sandboxHeinrich Schuchardt
The sandbox is using a virtual address space which is neither the physical address space of the operating system nor the virtual address space in which Linux aplications live. The addresses used insided the flattened device tree use this sandbox virtual address space. The EFI subsystem uses the virtual address space of the operating system and this is where the fdt is stored. Fix all incorrect addresses for the fdt in cmd/bootefi.cmd. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02fdt_support: fdt reservations on the sandboxHeinrich Schuchardt
On the sandbox the memory addresses in the device tree refer to the virtual address space of the sandbox. This implies that the memory reservations for the fdt also have to be converted to this address space. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02fdt: sandbox: correct use of ${fdtcontroladdr}Heinrich Schuchardt
The sandbox uses a virtual address space that is neither the physical nor the virtual address space of the operating system. All address used on the command line live in this address space. So also the environment variable ${fdtcontroladdr} has to be in this address space. Commands like bootefi and booti receive the fdt address as parameter. Without the patch ${fdtcontroladdr} cannot be used as parameter value on the sandbox. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: macro efi_size_in_pages()Heinrich Schuchardt
When allocating EFI memory pages the size in bytes has to be converted to pages. Provide a macro efi_size_in_pages() for this conversion. Use it in the EFI subsystem and correct related comments. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_selftest: building sandbox with EFI_SELFTESTHeinrich Schuchardt
Enable building the sandbox with CONFIG_EFI_SELFTEST. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_selftest: add test for memory allocationHeinrich Schuchardt
This unit test checks the following runtime services: AllocatePages, FreePages, GetMemoryMap Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: eliminate sandbox addressesHeinrich Schuchardt
Do not use the sandbox's virtual address space for the internal structures of the memory map. This way we can eliminate a whole lot of unnecessary conversions. The only conversion remaining is the one when adding known memory. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi: Rename bootefi_test_finish() to bootefi_run_finish()Simon Glass
This function can be used from do_bootefi_exec() so that we use mostly the same code for a normal EFI application and an EFI test. Rename the function and use it in both places. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi: Create a function to set up for running EFI codeSimon Glass
There is still duplicated code in efi_loader for tests and normal operation. Add a new bootefi_run_prepare() function which holds common code used to set up U-Boot to run EFI code. Make use of this from the existing bootefi_test_prepare() function, as well as do_bootefi_exec(). Also shorten a few variable names. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi: Split out test init/uninit into functionsSimon Glass
The functions in bootefi are very long because they mix high-level code and control with the low-level implementation. To help with this, create functions which handle preparing for running the test and cleaning up afterwards. Also shorten the awfully long variable names here. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi: Check for failure to create objects in selftestSimon Glass
At present a few error conditions are not checked. Before refactoring this code, add some basic checks. Note that this code still leaks memory in the event of error. This will be tackled after the refactor. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: Reserve unaccessible memoryAlexander Graf
On some systems, not all RAM may be usable within U-Boot. Maybe the memory maps are incomplete, maybe it's used as workaround for broken DMA. But whatever the reason may be, a platform can say that it does not wish to have its RAM accessed above a certain address by defining board_get_usable_ram_top(). In the efi_loader world, we ignored that hint, mostly because very few boards actually have real restrictions around this. So let's honor the board's wish to not access high addresses during boot time. The best way to do so is by indicating the respective pages as "allocated by firmware". That way, Operating Systems will still use the pages after boot, but before boot no allocation will use them. Reported-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by: Baruch Siach <baruch@tkos.co.il>
2018-12-02efi_selftest: incorrect use of bitwise orHeinrich Schuchardt
We should use a logical or when combining logical values. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02sandbox: smbios: Update to support sandboxSimon Glass
At present this code casts addresses to pointers so cannot be used with sandbox. Update it to use mapmem instead. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02Revert "efi_loader: remove efi_exit_caches()"Alexander Graf
This reverts commit 3170db63c41a2eda6ee6573353bb4de8c7c1b9d5. It reportedly breaks OpenBSD/armv7 booting and I've already received complaints from people that it breaks some Linux armv7 systems as well. We'll have to give this whole caching story a good bit more thought. Reported-by: Jonathan Gray <jsg@jsg.id.au> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: use u16* for UTF16 stringsHeinrich Schuchardt
We should be consistent in the types that we use to store Unicode strings. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: SetVirtualAddressMap() should return EFI_UNSUPPORTEDAKASHI Takahiro
See UEFI specification 2.7, section 8.4. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: correct a function prototype of QueryCapsuleCapabilities()AKASHI Takahiro
See UEFI specification v2.7, section 8.5.3. Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: correct efi_add_known_memory()Heinrich Schuchardt
If a memory bank is not EFI_PAGE_SIZE aligned efi_add_known_memory() the number of memory pages may be incorrectly calculated. We have to round up the start address and to round down the end address to determine which complete pages are provided by the memory bank. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
2018-12-02efi_loader: carving out memory reservationsHeinrich Schuchardt
The "Devicetree Specification 0.2" does not prescribe that memory reservations must be EFI page aligned. So let's not make such an assumption in our code. Do not carve out the pages for the device tree. This memory area is already marked as EFI_RUNTIME_SERVICES_DATA. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Alexander Graf <agraf@suse.de>
generated by cgit (git 2.34.1) at 2025-01-01 01:36:19 +0000