| Age | Commit message (Collapse) | Author |
|---|
|
The Pine H64 board comes with some onboard SPI flash chip, which is
perfect for loading SPL, ATF and U-Boot proper from there.
Enable the functionality in the defconfig, so that we use sunxi-fel to
transfer a bootable image to the NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
The Allwinner H6 SoC uses a quite different memory map, also changes the
clocks quite a bit. This requires some changes to the SPL SPI routine,
which hardcodes these values so far.
Using the just introduced helper functions to determine base address
and SPI controller generation, we can cover some of these differences
easily.
The clock setup is different, so requires some explicit code changes
there (reset and clock gate in one register at a different address).
Also we need to change the pinmux function to use a different set of
pins that the H6 uses for SPI0.
Eventually we can enable the H6 to use SPI booting in Kconfig.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Now that we can easily select an SoC specific SPI0 base address, adding
support for the Allwinner R40 is fairly trivial:
We set the base address, add this SoC to the ones that use PC23 and
enable it in Kconfig.
This allows booting from SPI flash on R40 boards.
Tested on a Bananapi M2 Berry with SPI flash connected to the header pins.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
So far we were using the CONFIG_SUNXI_GEN_SUN6I symbol to select between
the two SPI controller generations used on Allwinner SoCs. This is a
convenience symbol to roughly differentiate between "older" and "newer"
generation of SoCs.
The H6 SoCs is the newest SoC so far, but is sufficiently different to
not define this symbol. However it is using a SPI controller compatible
to the "new gen" SoCs.
To prepare for H6 support, we replace the check for this single symbol
with an explicit function, which can later be extended.
For now we just return CONFIG_SUNXI_GEN_SUN6I in there, so this does not
create a functional change.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
So far on all supported Allwinner SoCs we find the old generation SPI
controller always at address 0x1c05000, and the new generation one at
0x1c68000. However the Allwinner R40 SoC has a new generation SPI at
the old address, and the H6 uses a completely different address.
So split off the base address from the respective SPI registers, by
changing the #defines to just contain offsets.
The base address is provided by a function, so it can easily be extended
later when support for those SoCs materialises.
This does not change the code size (since the toolchain is clever enough
to optimise this properly), also does not bring any functional change at
this point.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
- Revert "sunxi: psci: avoid error address-of-packed-member"
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc4 (4)
This series fixes several bugs:
* consider the /reserved-memory node in the device tree
* consider memory reservations created in ft_board_setup()
* correct output of 'efidebug memmap' on the sandbox
* correct the definition of efi_capsule_header()
Furthermore some definitions needed for future patches are added to
header files.
|
|
- Fix sbi_remote_sfence_vma{,_asid}.
- Avoid calling sbi_clear_ipi().
- Add new SBI v0.2 extensions support.
|
|
Using memcpy() for some MMIO access is generally frowned upon and might
break things on some platforms. Allwinner H3, which fails to boot, being
an example here.
Moreover, fields being accessed are naturally aligned and warnings
produced by GCC have been quiesced for some time already by:
53dc8ae ("gcc-9: silence 'address-of-packed-member' warning")
That said, it should be okay to revert this commit.
This reverts commit 9bd34a69a453d409792e08c00953ce8862145e65.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Tomasz Duszynski <tduszyns@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
See UEFI specification, section 8.5.3.
In addition, the structure, efi_capsule_header, should be "packed"
as it is a serialized binary format in a capsule file.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
|
|
This is a preparatory patch.
Those functions will be used in an implementation of UEFI firmware
management protocol as part of my capsule update patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
|
|
Some of those values will be used in an implementation of UEFI firmware
management protocol as part of my capsule update patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
|
|
These flags are expected to be set in OsIndicationsSupported variable
if corresponding features are supported. See UEFI specification,
section 8.5.4.
In particular, capsule-related flags will be used in my capsule
update patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Fix misspelled EFI_OS_INDICATIONS_BOOT_TO_FW_UI.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Currently, bootefi only parses memory reservation block to setup
EFI reserved memory mappings. However, it doesn't parse the
reserved-memory[1] device tree node that also can contain the
reserved memory regions.
Add capability to parse reserved-memory node and update the EFI memory
mappings accordingly.
1. <U-Boot source>/doc/device-tree-bindings/reserved-memory/reserved-memory.txt]
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Fix an endless loop.
The /reserved-memory node may have children without reg property. Remove
a superfluous debug statement.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Addresses in the sandbox's device tree are in the sandbox's virtual address
space. If we want to compare memory reservations in the device-tree with
the output of 'efidebug memmap', we need to convert back to this address
space.
Adjust the output of the 'efidebug memmap' command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Some memory reservations are made in ft_board_setup(). Ensure that we
create reserved memory map entries after ft_board_setup().
The downside of this patch is that if bootefi is called multiple times with
an devicetree argument superfluous reservations for the old copies of the
device tree will exist. But that is still better than missing a reservation.
Deleting the superfluous reservations is not possible because reservations
in the memory map are rounded to page size and may be coallesced.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Few v0.1 SBI calls are being replaced by new SBI calls that follows
v0.2 calling convention.
Implement the replacement extensions and few additional new SBI
function calls that makes way for a better SBI interface in future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
We now have SBI v0.2 which is more scalable and extendable to handle
future needs for RISC-V supervisor interfaces.
Introduce a new config and move all SBI v0.1 code under that config.
This allows to implement the new replacement SBI extensions cleanly
and remove v0.1 extensions easily in future. Currently, the config
is enabled by default. Once all M-mode software, with v0.1, is no
longer in use, this config option and all relevant code can be easily
removed.
This commit is inspired from Linux kernel patch:
https://patchwork.kernel.org/patch/11407361/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
Few v0.1 SBI calls are being replaced by new SBI calls that follows
v0.2 calling convention.
This patch just defines these new extensions.
This commit is inspired from Linux kernel patch:
https://patchwork.kernel.org/patch/11407359/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
The SBI v0.2 introduces a base extension which is backward compatible
with v0.1. Implement all helper functions and minimum required SBI
calls from v0.2 for now. All other base extension function will be
added later as per need.
As v0.2 calling convention is backward compatible with v0.1, remove
the v0.1 helper functions and just use v0.2 calling convention.
Add a new Kconfig options CONFIG_SBI for the new SBI v0.2 codes, and
let CONFIG_SBI_IPI depend on it.
This commit is inspired from Linux kernel patch:
https://patchwork.kernel.org/patch/11407363/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
As per the new SBI specification, current SBI implementation version
is defined as 0.1 and will be removed/replaced in future. Each of the
function call in 0.1 is defined as a separate extension which makes
easier to replace them one at a time.
Rename existing implementation to reflect that. This patch is just
a preparatory patch for SBI v0.2 and doesn't introduce any functional
changes.
This commit is inspired from Linux kernel patch:
https://patchwork.kernel.org/patch/11407355/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
|
|
There is no need for S-mode U-Boot to call sbi_clear_ipi() as it
can be cleared directly from S-mode. This saves some cycles.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas@auer.io>
|
|
Currently sbi_remote_sfence_vma{,_asid} does not pass their arguments
to SBI at all, which is semantically incorrect.
This keeps in sync with Linux kernel commit:
a21344dfc6ad: fix sbi_remote_sfence_vma{,_asid}
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas@auer.io>
|
|
- Fix timer wrap (Chris)
- Use dev_read only if OF_PLATDATA is not enabled (Walter)
|
|
On some platforms/architectures the value from get_timer() can wrap.
This is particularly problematic when long-running code needs to measure
a time difference as is the case with watchdog_reset() which tries to
avoid tickling the watchdog too frequently.
Use time_after() from time.h instead of a plain > comparison to avoid
any issues with the time wrapping on a system that has been sitting in
u-boot for a long time.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Currently watchdog tries to use dev_read_u32_default to get timeout
configuration in case OF_CONTROL is enabled. However, if SPL is
built with OF_PLATDATA this has no sense as there is no device tree.
This patch fixes this issue by only use dev_read_u32_default if OF_CONTROL
is enabled but OF_PLATDATA is not.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
- Address the regression with the 'gpio' command
- Fix mcfuart regression
- Other minor fixes
|
|
Add STi drivers/include files and git tree.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
GCC-10 reports:
In file included from tools/common/image-fit.c:1:
include/image.h: In function ‘fit_image_get_data_and_size’:
./tools/../common/image-fit.c:1015:9: warning: ‘len’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
1015 | *size = len;
| ~~~~~~^~~~~
./tools/../common/image-fit.c:996:6: note: ‘len’ was declared here
996 | int len;
| ^~~
Add the missing check of the return value of fit_image_get_data_size().
Fixes: c3c863880479 ("add FIT data-position & data-offset property support")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
|
|
Just cleanup help indentation to be the same for all options.
It means <tab><space><space> indentation.
OMAP3 should be indented by tabs which is also fixed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
4dbc107f4683 ("cmd: gpio: Correct do_gpio() return value") correctly
changed the behaviour of the gpio command to return CMD_RET_SUCCESS or
CMD_RET_FAILURE, but any existing script which expects the return value
to be the pin value is broken by this change.
Reinstate the legacy behaviour for `gpio input` only.
Fixes: 4dbc107f4683 ("cmd: gpio: Correct do_gpio() return value")
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Alex Kiernan <alex.kiernan@hivehome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The commit 5fed97af20da ("Makefile: ensure DTB doesn't overflow into
initial stack") adds an extra check for stack size in BSS if
CONFIG_SYS_INIT_SP_BSS_OFFSET is enabled.
This check, however, doesn't make sense under the configuration where
control dtb won't be built in and it should be void in such cases.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Fixes: 5fed97af20da ("Makefile: ensure DTB doesn't overflow into initial stack")
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
All drivers seems to align now to serial_xxx maning, so, aligning
also this driver, to allow to be found easily.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
|
|
Actually, using dev->seq value before probe to deduce the current
serial port index leads to reading an invalid seq value (-1).
So, getting dev->seq at probe time.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc4 (3)
This pull request provides the hardware RNG driver for Amlogic systems needed
for the EFI_RNG_PROTOCOL.
Furthermore bug fixes are provided:
* correct an error message in the efidebug command
* correct an error in the 'efidebug rm' command
* remove an unnecessary assignment in efi_queue_event()
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp: fix dependency for CONFIG_STM32_ETZPC
|
|
Add support for the hardware random number generator of Amlogic SOCs.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
|
|
For all sandbox systems with DM_RNG we enable RNG_SANDBOX. So we can simply
set the default to yes.
All rng drivers depend on DM_RNG. Use a single 'if' instead of individual
dependencies. Now 'make menuconfig' shows the individual drivers neatly
indented under the DM_RNG entry.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
|
|
The assigned value NULL is never used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Add the missing line feed at the error message if the variable referred to
by 'efidebug boot rm' does not exist.
Shorten the format string by using the variable name instead of the number
of the boot variable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
There is a wrong usage of utf8_utf16_strncpy() in "boot rm" command, and
then it will end up with a failure of this command due to a wrong
value of an interim variable ("var_name16").
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Currently, if GetMemoryMap API returns EFI_BUFFER_TOO_SMALL, it doesn't
set valid values to other parameters, descriptor_size and
descriptor_version, except memory_map_size.
Some efi applications, however, may use those value; in particular,
xen uses descriptor_size to calculate a size of buffer to be allocated.
While UEFI specification is ambiguous in this point, it would be better
to address this issue proactively to maximize the compatibility with
existing efi applications.
With this patch, for example, xen.efi (and hence linux kernel) can be
started via bootefi without modification.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
- DM support for CAxxxx SoCs
- eMMC board for presidio-asic
- Add defer probe for mmc sdhci
- TI SoCs mmc misc update
|
|
The binman-option BINMAN_FDT is introduced by this commit:
commit 3c10dc95bdd0 ("binman: Add a library to access binman entries")
BINMAN_FDT being selected when BINMAN=y that resulting in mt7623
and mt7622 are unable to boot. The root cause of this issue is commit:
commit cbd2fba1eca1 ("arm: MediaTek: add basic support for MT7629 boards")
select BINMAN=y in all mediatek SoCs, and others mediatek SoCs not
expect to use BINMAN_FDT.
This patch remove BINMAN=y option when ARCH_MEDIATEK=y and
move this to the specify SoCs part config.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
|
|
Currently when booting the kernel on i.MX8 U-Boot hangs in an
endless loop when switching off dma, connectivity or lsio power
domains during device removal. It hapens first when removing
gpio0 (gpio@5d080000) device, here its power domain device
'lsio_gpio0' is obtained for switching off power. Since the
obtained 'lsio_gpio0' device is removed afterwards, its power
domain is also switched off and here the parent power domain
device 'lsio_power_domain' is optained for switching off the
power. Thereafter, when the obtained 'lsio_power_domain' is
removed, device_remove() removes its first child 'lsio_gpio0'.
During this child removal the 'lsio_power_domain' device is
obtained again for switching and when removing it later,
the same child removal is repeated, so we are stuck in an
endless loop. Below is a snippet from dm tree on i.MX8QXP
for better illustration of the DM devices relationship:
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
...
simple_bus 0 [ + ] generic_simple_bus |-- imx8qx-pm
power_doma 0 [ + ] imx8_power_domain | |-- lsio_power_domain
power_doma 1 [ + ] imx8_power_domain | | |-- lsio_gpio0
power_doma 2 [ + ] imx8_power_domain | | |-- lsio_gpio1
Do not remove a power domain device if it is a parent of the
currently controlled device.
Fixes: 52edfed65de9 ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Oliver Graute <oliver.graute@gmail.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2020.04
-----------------
- DM : mx6sabresd
- mx6ul_14x14_evk: fix video
- mx8qxp; fix console for booting
- sync DTS with kernel (imx6sx)
- drop obsolete woodburn (mx35)
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/660550811
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2020.04 cycle:
- Includes two small configuration fixes that will solve the SPL booting
on sama5d3_xplained board.
|
|
Correct the dependency for STM32 ETZPC protection, linked to SOC
STM32MP identified by CONFIG_STM32MP15x and not linked to
CONFIG_TARGET_STM32MP1 (no more existing).
This patch fix an issue introduced by commit 846254888e2e ("stm32mp1:
split board and SOC support for STM32MP15x family").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
|
|
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
