Age | Commit message (Collapse) | Author |
|
from https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git/
tag "ux500-armsoc-v5.6-2"
commit 224bf0fe7292 ("ARM: dts: ux500: samsung-golden: Add Bluetooth")
(queued for merge in Linux 5.6)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Nomadik Multi Timer Unit (MTU) provides 4 decrementing
free-running timers. It is used in ST-Ericsson Ux500 SoCs.
The driver uses the first timer to implement UCLASS_TIMER.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
I'm also seeing the build failure that commit
7d4776545b env: solve compilation error in SPL
tried to fix, namely that the reference to env_flags_validate from
env_htab cannot be satisfied when flags.o is not built in. However,
that commit got reverted by
d90fc9c3de Revert "env: solve compilation error in SPL"
Necessary, but not sufficient conditions to see this are
CONFIG_SPL=y (obviously)
CONFIG_SPL_ENV_SUPPORT=n (so flags.o does not get compiled)
CONFIG_SPL_LIBCOMMON_SUPPORT=y (so env/built-in.o is part of the SPL link)
Now, these are satisfied for e.g. imx6q_logic_defconfig. But that
builds just fine, and spl/u-boot-spl.map lists .data.env_htab among
the discarded (garbage collected) sections. Yet, on our
mpc8309-derived board, we do see the build failure, so perhaps the
linker works a bit differently on ppc than on ARM, or there's yet some
other configuration option needed to observe the break.
This is another attempt at solving it, which also cleans up
env/Makefile a bit: Introduce a def_bool y symbol CONFIG_ENV_SUPPORT
which complements CONFIG_(SPL/TPL)_SUPPORT. Then use
CONFIG_$(SPL_TPL_)ENV_SUPPORT to decide whether to include the five
basic env/*.o files. For attr.o, flags.o and callback.o, this
shouldn't change anything. Also, common.o and env.o still get
unconditionally built for U-boot proper. But for TPL/SPL, those two
are only included if CONFIG_(SPL/TPL)_SUPPORT is set.
Having that symbol should also allow simplifying conditionals such as
#if !defined(CONFIG_SPL_BUILD) || CONFIG_IS_ENABLED(ENV_SUPPORT)
found in drivers/reset/reset-socfpga.c to just
CONFIG_IS_ENABLED(ENV_SUPPORT).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
|
|
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
- Clearfog: Add run-time board detection with TLV EEPROM support
(Baruch)
|
|
Clearfog Base carrier uses serdes lane #5 as USB host. Use EEPROM stored
device identification to configure the serdes accordingly when
available.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
Select the serdes configuration table based on the platform identity
read from EEPROM TLV data. Clearfog GTR needs a slightly different
serdes configuration.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
Set the kernel device-tree file (fdtfile environment variable) based on
run-time detection of the platform.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
Use the data from EEPROM TLV to display the board identity.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
Read RAM die capacity from the EEPROM TLV.
Follow the ONIE standard that defines the Vendor Extension entry type
for vendor specific data. We have no Private Enterprise Number at the
moment as the standard requires. Use the dummy all 0xff value for now.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
Add support for read/write of ONIE "Tlvinfo" EEPROM data format. TLV
stands for Type-Length-Value. The data format is described here:
https://opencomputeproject.github.io/onie/design-spec/hw_requirements.html#board-eeprom-information-format
Based on U-Boot patch from the Open Compute project:
https://github.com/opencomputeproject/onie/blob/ec87e872d46b9805565d2c6124b2f701ef1c07b1/patches/u-boot/common/feature-sys-eeprom-tlv-common.patch
Keep only I2C EEPROM support. Use the generic eeprom driver. Fix
checkpatch issues.
Add support for multiple EEPROM TLV stores on the same system. This is
useful in case of SOM and carrier that both provide ID and hardware
configuration information.
Add option to enable for SPL. This allows selection of RAM configuration
based on EEPROM stored board identification.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
Add device-tree description for the EEPROM devices on Armada 388 SOM rev
2.1.
Another EEPROM is now on Clearfog Pro carrier rev 2.2, and Clearfog Base
rev 1.3.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-imx
---------------------------------
imx8: cleanup, fix warnings
imx6ull: add VisionSOM SoM and EVK
mx7ulp: fix warning due network, cleanup
mx7dsabre: Fix dm probe pmic
imx6: fixed for vining2000
Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/639512296
|
|
Enabled both DDR clock signals to support Clearfog variants (currently,
Clearfog GTR) that need both clocks.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
DDR clock out might be unrelated to the number of active chip-select.
For example, the board might have two DDR components, but only one
chip-select. The clk_enable mask allows the board to enable DDR clocks
regardless of active chip-selects.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-ti
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
|
|
https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp1: split SOC and board and cleanup config
|
|
- Bring in Simon Glass's series that reduces what we have in <common.h>
even more.
|
|
- Based on bionic-20200112 tag from Ubuntu
- Add graphviz (Heinrich)
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/toradex/colibri-imx8x/colibri-imx8x.c:104:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
|
|
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/toradex/apalis-imx8/apalis-imx8.c:92:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
|
|
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:115:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
|
|
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:102:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
|
|
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/advantech/imx8qm_rom7720_a1/imx8qm_rom7720_a1.c:110:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
|
|
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:116:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
|
|
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:129:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
|
|
Add prototype to function spl_board_boot_device to fix the following
sparse warning:
board/freescale/imx8mm_evk/spl.c:26:5: warning: no previous prototype
for ‘spl_board_boot_device’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
|
|
Functions spl_dram_init() and power_init_board() are used only in
the scope of this file, so make them static to fix the following sparse
warnings:
board/freescale/imx8mm_evk/spl.c:40:6: warning: no previous prototype
for ‘spl_dram_init’ [-Wmissing-prototypes]
board/freescale/imx8mm_evk/spl.c:85:5: warning: no previous prototype
for ‘power_init_board’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
|
|
Functions fracpll_configure(), decode_intpll(), decode_fracpll(),
get_root_src_clk() and get_root_clk() are used only in the scope of this
file, so make them static to fix the following sparse warnings:
arch/arm/mach-imx/imx8m/clock_imx8mm.c:50:5: warning: no previous
prototype for ‘fracpll_configure’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:271:5: warning: no previous
prototype for ‘decode_intpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:418:5: warning: no previous
prototype for ‘decode_fracpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:483:5: warning: no previous
prototype for ‘get_root_src_clk’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:527:5: warning: no previous
prototype for ‘get_root_clk’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
|
|
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
|
|
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
|
|
Add sys_proto.h header file to fix the following sparse warning:
board/freescale/imx8mm_evk/imx8mm_evk.c:59:5: warning: no previous
prototype for ‘board_mmc_get_env_dev’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
|
|
The mux mode is embedded in the PAD definition and therefore there is
no need to repeat it in the PAD configuration value (more over since
this information will be masked out when the configuration value is
applied).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
The imx8mm doesn't require the hdmi firmware.
Update also the fw version.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
With commit 0d52bab4621 ("mx7dsabre: Enable DM_ETH")
Device Tree has been update and change pfuze3000 node
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
On SPL enabled systems, the current s_init code (wdog, clock and ldo
init) is executed twice (by SPL and u-boot). This is not necessary and
might lead to boot issues (ie, starting PMC1 when it is already running).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx7ulp-evk board does not have networking support, explicitly
disable networking.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
|
|
Fix dtb building warnings:
Warning (cooling_device_property): /thermal-zones/cpu-thermal0/cooling-maps/map0:
Missing property '#cooling-cells' in node /cpus/cpu@0 or bad phandle (referred from cooling-device[0])
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
|
|
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Enable SPL SDP fallback boot option in default build.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
The PFUZE100 and PFUZE200 PMICs can be discerned by bit 0 in DeviceID
register. Print the correct identification of the PMICs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Simplify the uSDHC4 eMMC controller setup. This is the only eMMC
present on the system and only controller that is used, so drop
the extra logic.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
In locked condition CLKOUT = CLKINP * [M / (N + 1)].
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add slack to the clock frequency parameters passed to firmware within
clk_set_rate. min-freq is changed to 0 and max-rate is changed to
ULONG_MAX. This fixes certain issues with pll clock rounding when the
firmware is not able to set the frequency exactly to the target, the
current implementation fails if the available frequency is even 1Hz off
the target. With the change, the firmware still tries its best to set
the frequency as close as possible to the target.
Reported-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Take over TI maintainership from Tom.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Enable USB keyboard to be used as input device at U-Boot prompt. Both
serial and USB keyboard will be active inputs simultaneously.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Enable configs related to USB Host mode, Peripheral mode and DFU.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Add env variables that set up dfu_alt_info for MMC/EMMC/OSPI. This
is required to allow update of firmware on these media.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|