summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-12-11Fix use of conditional LMBSimon Glass
This code was not guarded with CONFIG_LMB so failed to build on x86. Signed-off-by: Simon Glass <sjg@chromium.org>
2012-12-11Add a command to read raw blocks from a partitionKenneth Waters
Sometimes data is on a block device and within a partition, but not in a particular filesystem. This commands permits reading raw data from a partition. Signed-off-by: Kenneth Waters <kwaters@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
2012-12-11Add gettime commandAnton Staaf
Gettime returns the current timer value. If CONFIG_SYS_HZ is defined then the timer value is also converted to seconds. Tegra20 (SeaBoard) # gettime Timer val: 7754 Seconds : 7 Remainder : 754 sys_hz = 1000 There has been some discussion about whether this is useful enough to be included in U-Boot. The following boards do not have CONFIG_SYS_HZ defined: M52277EVB M52277EVB_stmicro M53017EVB M54418TWR M54418TWR_nand_mii M54418TWR_nand_rmii M54418TWR_nand_rmii_lowfreq M54418TWR_serial_mii M54418TWR_serial_rmii Signed-off-by: Anton Staaf <robotboy@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org>
2012-12-11Add new bootstage step for the main loopSimon Glass
Mark when we get to the main loop. Signed-off-by: Simon Glass <sjg@chromium.org>
2012-12-11gpio: remove duplicate function signatureNikita Kiryanov
gpio_request() appears twice in asm-generic/gpio.h Remove one of the definitions. Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2012-12-11designware_i2c.h: Define IC_CLK only if not already defined in config fileArmando Visconti
Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11designware_i2c.h: Fixed the correct values for SCL low/high timeArmando Visconti
Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11designware_i2c: Fixed the setting of the i2c bus speedArmando Visconti
There are three couple (hcnt/lcnt) of registers for each speed (SS/FS/HS). The driver needs to set the proper couple of regs according to what speed we are setting. Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11designware_i2c: Added s/w generation of stop bitArmando Visconti
In the newer versions of designware i2c IP there is the possibility of configuring it with IC_EMPTYFIFO_HOLD_MASTER_EN=1, which basically requires the s/w to generate the stop bit condition directly, as the h/w will not automatically generate it when TX_FIFO is empty. To avoid generation of an extra 0x0 byte sent as data, the IC_STOP command must be sent along with the last IC_CMD. This patch always writes bit[9] of ic_data_cmd even in the older versions, assuming that it is a noop there. Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11designware_i2c.c: Added the support for MULTI_BUSArmando Visconti
This patch adds the capability to switch between 10 different I2C busses (from 0 to 9). Signed-off-by: Armando Visconti <armando.visconti@st.com>
2012-12-11drivers:i2c: Modify I2C driver for Exynos4Piotr Wilczek
This patch modifies the S3C i2c driver to support both Exynos4 and Exynos5 Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com>
2012-12-11exynos:pinmux: Add pinmux support for i2cPiotr Wilczek
This patch add pinmux for I2C for Exynos4 Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com>
2012-12-11exynos:cpu: Add Exynos4 I2C spacingPiotr Wilczek
This patch add the spacing for i2c for Exynos4 Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com>
2012-12-11exynos:clock: Add i2c clockPiotr Wilczek
This patch adds i2c clock for Exynos4 Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com>
2012-12-11omap24xx_i2c: Handle OMAP5 like OMAP2,3,4Vincent Stehlé
OMAP5 has 8b i2c data register field, like OMAP2, 3 and 4. Handle in the same way. This fixes the following error on OMAP5: OMAP5430 EVM # mmc rescan timed out in wait_for_bb: I2C_STAT=1410 twl6035: could not turn on LDO9. Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
2012-12-11mxs: i2c: Implement algorithm to set up arbitrary i2c speedMarek Vasut
This algorithm computes the values of TIMING{0,1,2} registers for the MX28 I2C block. This algorithm was derived by using a scope, but the result seems correct. The resulting values programmed into the registers do not correlate with the contents in datasheet. When using the values from the datasheet, the I2C clock were completely wrong. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Wolfgang Denk <wd@denx.de>
2012-12-11mxs: i2c: Restore speed setting after block resetMarek Vasut
The I2C block reset configures the I2C bus speed to strange value. Read the I2C speed from the block before reseting the block and restore it afterwards, so the I2C operates correctly. This issue can be replicated by doing unsuccessful I2C transfer, after such transfer finishes, the I2C block clock speed is misconfigured. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11i2c: mxs: Fix TIMING2 register valueMarek Vasut
According to FSL, the value in the TIMING2 register shall be 0x00300030 instead of what's written in the datasheet. This new value correlates with older STMP36xx datasheet. Issues were detected in Linux when this register was misconfigured, so write this correct value. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11i2c: mxs: Use i2c_set_bus_speed() in i2c_init()Marek Vasut
Use i2c_set_bus_speed() in i2c_init() within the mxs i2c driver to avoid duplication of code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11i2c: mxs: Implement i2c_get/set_bus_speed()Marek Vasut
This patch implements the setup and retrieval functions for the I2C bus speed on the MXS I2C IP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11i2c: mxs: Abstract out the MXS I2C speed setupMarek Vasut
This patch pulls out the I2C speed setup from the i2c_init() call and implements the bus configuration lookup table with register values that needs to be programmed into the I2C IP to run at particular speed. This patch is a first step towards implementing run-time I2C bus speed configuration for the MXS I2C IP. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-11i2c: kerneldoc: Add kerneldoc annotations to cmd_i2c.cMarek Vasut
Add kerneldoc style documentation into cmd_i2c.c to properly describe all overridable functions and most of the command interface. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de>
2012-12-11i2c: Staticize local functions in mxc i2c driverMarek Vasut
Some functions in the MXC i2c driver were not static, fix this by making them so. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de>
2012-12-11i2c: Use __weak instead of __attribute__((weak, alias))Marek Vasut
Use __weak from linux/compiler.h instead of __attribute__((weak, alias)) to define overridable function. This patch is intended as a cleanup patch to bring some consistency into the code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de>
2012-12-11soft_i2c: add necessary includes for AVR32Andreas Bießmann
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2012-12-11woodburn: Set gpio value in gpio_direction_output()Fabio Estevam
Set the gpio value in gpio_direction_output() instead of an extra gpio_set_value call. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-12-11mx25pdk: Adapt it for the new PMIC frameworkFabio Estevam
Make the necessary adaptions for the new PMIC framework, so that mx25pdk can be built again. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
2012-12-11Correct comment to show the parameters as defined in tools/mkimage.hLars Rasmusson
Signed-off-by: Lars Rasmusson <Lars.Rasmusson@sics.se>
2012-12-11universal_c210: check the NULL pointer when get the PMICMinkyu Kang
PMIC 2.0 require to test return pointer from pmic_get() Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2012-12-11SMDK5250: Enable pmic MAX77686Rajeshwari Shinde
Enabled pmic MAX77686 for SMDK5250. Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-12-11POWER: MAX77686: Modified as per the latest ImplementationRajeshwari Shinde
Moved the pmic_max77686.c max77686_pmic.h to drivers/power and made required changes accordingly Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com> Acked-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2012-12-10cm-t35: enable zero bootdelay checkNikita Kiryanov
Enable zero bootdelay check to make it possible to abort autoboot even if bootdelay == 0 Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2012-12-10power: twl6035: complain on LDO9 errorVincent Stehlé
We handle i2c_write return code and complain in case of error. We propagate the error, too, to allow better handling at the upper level in the future. Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
2012-12-10omap24xx_i2c: Handle wait_for_bb errorVincent Stehlé
We add a return code to wait_for_bb() to be able to report errors to the callers properly. We in turn handle this new error code in i2c_read, i2c_write and i2c_probe. Signed-off-by: Vincent Stehlé <v-stehle@ti.com>
2012-12-10gpio: add gpio_is_valid() to omap_gpio APINikita Kiryanov
Add gpio_is_valid() to omap_gpio API Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2012-12-10OMAP3: Remove unused PHYS_SDRAM_1_SIZEThomas Weber
Remove the unused PHYS_SDRAM_1_SIZE from OMAP3 config files. Signed-off-by: Thomas Weber <thomas@tomweber.eu>
2012-12-10am335x: cpsw: make phy address configurableYegor Yefremov
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2012-12-10am335x: disable internal delay for RGMII modeYegor Yefremov
According to errata the AM335x device does not support internal delay mode, so RGMII1_IDMODE and RGMII2_IDMODE must be set to 1. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2012-12-10OMAP3: TAM3517: add macros for reading eepromStefano Babic
Added macros to read SOM information from the I2C EEPROM. Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-12-10OMAP3: fix panel timing on the mt_ventoux boardStefano Babic
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-12-10davinci: fixed cpu resetDavide Bonfanti
The reset procedure works on watchdog timer while before it was modifying TIMER_1 registers. Tested on DM365. Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
2012-12-10OMAP3 SPI : Fixed bugs related to SPI transferajoy
Added posted writes (read after writes) to effect the change immediately for channel confiuration and channel enable register Disable the channel to purge receieve data in TX_ONLY mode transfer otherwise rx data will get affected by the next immediate RX_ONLY mode transfer Wait for the EOT bit to be set after last byte has been loaded to TX shift register in the the TX_ONLY mode.This ensures TX data has been completely shifted out Disable the channel in RX_ONLY mode before reading the last data from RXX register to prevent the SPI slave to transmit next word Signed-off-by: Ajoy Kumar Das <akdas75@yahoo.in> Cc: Tom Rini <trini@ti.com> Cc: jacopo mondi <j.mondi@voltaelectronics.com>
2012-12-10omap: emif: configure emif only when requiredLokesh Vutla
DMM_LISA_MAP registers program whether memory is mapped on particular EMIF or not. Irrespective of these registers EMIF is getting configured. Correcting the same. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2012-12-10OMAP: Tweak omap-common/Makefile since reset.S -> reset.cRobert P. J. Day
Git commit d417d1db5f9092d125ddea882ced77eaa5f3d236 replaced the omap-common file reset.S with reset.c, but the Makefile was not adjusted for that. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-12-10omap4: Add comments on some "#endif"s for readability.Robert P. J. Day
No functional changes, simply for readability. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-12-10omap3: Add a few comments to "#endif"s for readability.Robert P. J. Day
No functional changes, just more comments for readability when a preprocessor check spans more than a few lines, and for consistency. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-12-10Pass sdrc timing values through board_sdrc_timings structurePeter Barada
Instead of passing individual registers by value to board_get_mem_timings, pass a board_mem_timings structure pointer for the board files to fill in. Pass same structure pointer to write_sdrc_timings. This saves about 90 bytes of space in SPL. Signed-off-by: Peter Barada <peter.barada@logicpd.com>
2012-12-10omap3_beagle.h: Fix comment for true/false return value.Robert P. J. Day
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
2012-12-10am335x_evm: enable SPL NAND supportIlya Yanok
Enable booting from NAND support from AM335x boards as well as environment in NAND. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-12-10am33xx_spl_bch: simple SPL nand loader for AM33XXIlya Yanok
AM33XX with BCH8 can't work with nand_spl_simple correctly because custom read_page implementation is required for proper syndrome generation. This simple driver mostly duplicates nand_spl_simple but has nand_read_page changed to suit our needs. Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
generated by cgit (git 2.34.1) at 2025-01-17 06:33:41 +0000