| Age | Commit message (Collapse) | Author |
|---|
|
cache_wback_all() is a local function and it is called from
cache_control() only, which is in turn jumps to P2 area.
The change fixes an issue when cache_wback_all() returns from P2 to
P1, however cache_control() continues to manipulate with CCR
register, according to the User's Manual this is restricted.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
Both jump_to_P2() and back_to_P1() functions are found in asm/system.h
header file and functionally they are the same, don't redefine them.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The change is similar to commit 994b56616bae ("sh: delete an unused
source file") for SH2, however here the removed cache.c file was
built and included into an image as a dead code.
If it is needed in future the contents can be reused from a similar
arch/sh/cpu/sh4/cache.c file, which is in turn will be moved to
a shared among all core flavours location at arch/sh/lib/cache.c.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In common usecases flush_cache() assumes both cache invalidation and
write-back to memory, instead of doing cache invalidation only with
the wrapped 'ocbi' instruction pin flush_cache() to cache invalidation
with memory write-back done by 'ocbp'.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In common usecases flush_cache() assumes both cache invalidation and
write-back to memory, thus in flush_dcache_range() implementation
change SH4 cache write-back only instruction 'ocbwb' with cache purge
instruction 'ocbp', according to the User's Manual there should be no
performance penalty for that.
Note that under circumstances only cache invalidation is expected from
flush_cache() call, in these occasional cases the current version of
flush_cache() works, which is a wrapper over invalidate_dcache_range()
at the moment, this will be fixed in the following change.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
|
|
When building u-boot on sparc64 and powerpc hosts it became clear that
u-boot expects endian conversion defines to be macros:
lib/crc32.c:87: error: braced-group within expression allowed only inside a function
For OpenBSD switch from using system definitions equivalent to the u-boot ones
and define glibc __BYTE_ORDER __BIG_ENDIAN __LITTLE_ENDIAN names, as at least
some parts of the non-cross build assumes those names are present (ie crc32.c).
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
|
|
AM57xx GP EVM has USB2 port of the SoC exposed as
USB client port.
It is useful to be able to use this port for USB
DFU downloads.
Enable USB DFU support. Tested on AM57x GP EVM Rev
A3 using DFU to download to connected SD card.
configs for HS version of the AM57x EVM are
included in the patch but not really tested.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Introduce include/environment/ti/dfu.h that
consolidates environment variable definitions
for various TI boards that support DFU today.
Tested on AM335x EVM, AM437x SK EVM and DRA74x
EVM by using DFU to write to SD card.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Move the macro to Kconfig SYS_FSL_NUM_LAWS.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Clean up existing definitions and drop from white list.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Some header files have this macro defined conditionally and
redefined unconditionally. Remove all existing definitions.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Move from CONFIG_SYS_EXTRA_OPTIONS to Kconfig option.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Move from CONFIG_SYS_EXTRA_OPTIONS to Kconfig option.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Move from CONFIG_SYS_EXTRA_OPTIONS to Kconfig option.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
At present buildman leaves behind a few characters during its progress
updates, which looks odd. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
When using #define CONFIG_SOME_OPTION, the value it set to '1'. When using
defconfig (i.e. CONFIG_SOME_OPTION=y) the value is set to 'y'. This results
in differences showing up with -K. These differences are seldom useful.
Adjust buildman to suppress these differences by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
The -K option is not mentioned in the README at present. Add some notes
to describe how this is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Normally buildman does a full build of a board. This includes creating the
u-boot.cfg file which contains all the configuration options. Buildman uses
this file with the -K option, to show differences in effective configuration
for each commit.
Doing a full build of U-Boot just to create the u-boot.cfg file is wasteful.
Add a -D option which causes buildman to only create the configuration. This
is enough to support use of -K and can be done much more quickly (typically
5-10 times faster).
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
A common requirement when converting CONFIG options to Kconfig is to check
that the effective configuration has not changed due to the conversion. Add
a target which creates this configuration (in the form of u-boot.cfg) but
does not build U-Boot. This speeds up the checking.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Now that we free resources in sandbox_fs_ls Coverity is letting us know
that in some cases we might leak. So in case of error we should still
let os_dirent_free free anything that was allocated.
Fixes: 86167089b71c ("sandbox/fs: Free memory allocated by os_dirent_ls")
Reported-by: Coverity (CID: 153450)
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The Atmel AT97SC3204 is also TIS compliant.
Modify the tpm_tis_lpc driver to check for the vid/did used by the
Atmel AT97SC3204 and report an appropriate description.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
GCC 6.2 reasonably complains about the current code:
../cmd/tpm_test.c: In function ‘do_tpmtest’:
../cmd/tpm_test.c:540:3: warning: this ‘for’ clause does not guard... [-Wmisleading-indentation]
for (i = 0; i < argc; i++)
^~~
../cmd/tpm_test.c:542:4: note: ...this statement, but the latter is misleadingly indented as if it is guarded by the ‘for’
printf("\n------\n");
^~~~~~
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Updated to remove C99 variable decl:
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Now all mpc85xx and mpc86xx have converted to use SYS_CCSRBAR_DEFAULT
in Kconfig. Drop this macro for LSCH2 and remove from white list.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Move default value definitions to Kconfig SYS_CCSRBAR_DEFAULT.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Move default value definitions to to Kconfig SYS_CCSRBAR_DEFAULT.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Instead of using EXTRA options in defconfig, use two targets
in Kconfig to select correct SoC.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
Two functions should be static because they are not exported to any
other file.
Warnings were reported by sparse C=1.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When blk_create_device() is called some parameters in blk_desc are
automatically filled. Separate SCSI private initialization and SCSI full
block device initialization not to rewrite already prepared data.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With DM_SCSI this function will return more than one return value to
cover errors.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Several functions should be static because they are not exported to any
other file.
Warnings were reported by sparse C=1.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
These functions are not called for any location.
This patch removes them scsi_trim_trail(), scsi_get_disk_count()
and scsi_setup_read6().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
There is no reason to directly point to static allocated array
when we have proper block_dev pointer available via parameter
in !CONFIG_BLK. For CONFIG_BLK this is read directly from uclass
platdata.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
pccb is pointer to temporary buffer which is used only for sending
command. Make it local as is done in scsi_read/scsi_write.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Prepare LUN(Logical unit number) directly in block description structure
and reuse it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The patch enables running detection algorithm on block device
description structure.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Extract block device initialization to specific function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
It is confusing that mdio commands work and report phy id as
decimal value when mii is working with hex values.
For example:
ZynqMP> mdio list
gem:
21 - TI DP83867 <--> ethernet@ff0e0000
ZynqMP> mdio read ethernet@ff0e0000 0
Reading from bus gem
PHY at address 21:
0 - 0x1140
ZynqMP> mii dump 21 0
Incorrect PHY address. Range should be 0-31
...
ZynqMP> mii dump 15
0. (1140) -- PHY control register --
(8000:0000) 0.15 = 0 reset
U-Boot normally takes hex values that's why this patch is changing mdio
command to handle hex instead of changing mii command to handle decimal
values.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Enable SD1 and qspi for picozed board.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
ARCH_ZYNQ(MP) selects DM_USB, where CONFIG_USB_MAX_CONTROLLER_COUNT
is not used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Using alternative bootmode field to support automatic secondary boot
modes. It is purely software setting where SW modes are using free
bootmode combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
CONFIG_SYS_CONFIG_NAME is not proper config option for different low
level init files because different board revisions requires different
psu_init_gpl* files.
Also at the end of moving drivers to DM all board specific configuration
files should be removed.
The same changes was done for Zynq.
"ARM: zynq: Simplify zynq configuration"
(sha1: ad5b5801264e573bfbf17a20b04c546985c5bfc1)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
ZynqMP provides an option to overwrite bootmode setting which
can change SPL behavior.
For example: boot SPL via JTAG and then SPL loads images from SD.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
|
|
Offset 0x1 in the generated kwb image file is a set of flags, bit 0
enables debug output from the BootROM firmware. Allow a DEBUG option in
the kwb configuration to request debug output from the BootROM firmware.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Offset 0x18 in some Marvell datasheets this field is redacted as
"reserved". This offset is actually a set of options and bits 2:0 allow
the selection of the UART baudrate.
Allow a BAUDRATE option to set the UART baudrate for any messages coming
from the BootROM firmware.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The main PLL frequency is 2GHz for Armada-XP and 1GHZ for Armada 375,
38x and 39x.
[ Linux commit ae142bd9976532aa5232ab0b00e621690d8bfe6a ]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Make the spl_mmc_load_image() available globally, so it can be
invoked directly by SPL on extremely space-constrained systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Add new configuration option CONFIG_MMC_TINY which strips away all
memory allocation within the MMC code and code for handling multiple
cards. This allows extremely space-constrained SPL code use the MMC
framework.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
|
|
If debug() is not used, then the whole content of debug(...) will
be removed by the preprocessor, which will result in the following
warning. This patch adds __maybe_unused annotation to fix this.
drivers/mmc/mmc.c: In function ‘mmc_init’:
drivers/mmc/mmc.c:1685:11: warning: variable ‘start’ set but not used [-Wunused-but-set-variable]
unsigned start;
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
|
