summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-09-12test: do no assume hush parser in validate_empty()Heinrich Schuchardt
The environment variable test uses function validate_empty() to check that a variable is not defined. If the hush parser is not enabled, we cannot refer to a variable by $var_name but only by ${var_name}. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Stephen Warren <swarren@nvidia.com>
2020-09-12Makefile: mrproper shall delete doc/output/Heinrich Schuchardt
HTML documentation is generated in doc/output/. This directory shall be deleted by 'make mrproper' Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-09-12doc: describe building with GCCHeinrich Schuchardt
Provide a description of the U-Boot build process with GCC in the HTML documentation. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-12doc: describe source repositoryHeinrich Schuchardt
Add a chapter to the HTML documentation describing how to retrieve the U-Boot sources. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-12ARM: MediaTek: amend IC description for MediaTek MT8512Mingming Lee
The description for MT8512 has some mistake, so correct it. Signed-off-by: Mingming Lee <Mingming.Lee@mediatek.com>
2020-09-11Fix data abort caused by mis-aligning FIT dataReuben Dowle
Attempting to place device tree immediately after an image in memory can lead to mis-aligned data accesses if that image size is not divisible by the alignment requirements of the architecture. Data aborts caused by this were observed on a custom Marvel A388 based system, where the image was a uboot FIT file. The total size varies depending on the uboot device tree size, which does not always lead to correct alignment. The minimum alignment specified for ARM [1] and ARM64 [2] linux booting has been used [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/arm/booting.rst#n126 [2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/arm64/booting.rst#n45 Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
2020-09-11mtd: nand: Fix nand write error with bad block addresses above 32-bitT Karthik Reddy
Nand writes should skip the bad blocks with "nand write" command. In case of bad blocks with above 32-bit address, nand_block_isbad() returns false due to truncated bad block address. In below code segment, if (nand_block_isbad(mtd, offset & ~(mtd->erasesize - 1))) offset is 64-bit and mtd->erasesize is 32-bit, hence the truncation is happening. Cast 'mtd->erasesize' with loff_t to fix this issue. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-09-11env: Crash in 'env import' when using checksum and a specific sizePedro Aguilar
This patch adds a sanity check that avoids 'size' to overflow and crash when importing an environment that contains a checksum. Example with the wrong size that causes the crash: => env import -c 0x4100000 3 v1 This assumes that v1 has already been successfully exported with 'env export -c -s 0x100 0x4100000 v1' Signed-off-by: Pedro Aguilar <pedro.aguilar@vimar.com>
2020-09-11bootm: update image OS image size when decompressingHeinrich Schuchardt
In bootm_load_os() the OS image is decompressed. In later stages of the boot process we need the decompressed size of the image. Update images->os.image_len after decompression. Passing the correct size is necessary if we want to check loaded EFI binararies for file truncation by comparing the loaded size to the header field SizeOfImage. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-09-11common: Kconfig: Add dependency for default variables stringsMichal Simek
Kconfig provides several config options for setting up default variables but these are unused when variables are passed to U-Boot via file. That's why cover this dependency in Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-09-10PCI: mediatek: Release the resource when PCIe enable port failChuanjia Liu
On the mt7623 platform, if one port enable fail and other port enable succeed. It will hang on when using pci enum because the resource was not released correctly. Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com> Tested-by: Frank Wunderlich <frank-w@public-files.de>
2020-09-10Merge tag 'u-boot-amlogic-20200910' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - enables HDMI output & USB keyboard for Odroid-N2 - setups HDMI output background & enables USB keyboard
2020-09-10configs: odroid-c4: update for HDMI output background & USB keyboardAnand Moon
Enable options SYS_WHITE_ON_BLACK to permit HDMI background screen from white to back, also enable USB_KEYBOARD. Signed-off-by: Anand Moon <linux.amoon@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-09-10configs: odroid-n2: update for HDMI output & USB keyboardAnand Moon
Enable options to permit HDMI output on Odroid-N2 G12B boards. Enable VPU Power Domain. Enable USB_KEYBOARD. Signed-off-by: Anand Moon <linux.amoon@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-09-09Merge tag 'u-boot-stm32-20200909' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - fixes on AV96 board: pull up on UART4 RX and adjust PLL4
2020-09-09ARM: dts: stm32: Adjust PLL4 settings on AV96 againMarek Vasut
PLL4Q is supplying both FDCAN and LTDC. In case HDMI is in use, the 50 MHz generated from PLL4Q cannot be divided well enough to produce accurate clock for HDMI pixel clock. Adjust it to generate 74.25 MHz instead. The PLL4P/PLL4R are generating 99 MHz instead of 100 MHz, which is in tolerance for the SDMMC. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Gerald Baeza <gerald.baeza@st.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-09-09ARM: dts: stm32: Pull UART4 RX high on AV96Marek Vasut
There is no dedicated pull resistor on the AV96 UART4 (console UART) pin. In case there is no UART adapter installed on the AV96, the line is floating and can trigger reception of garbage characters, which in turn can abort U-Boot autoboot. Add default pull up to mitigate this problem. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2020-09-09arm: stm32mp: cleanup test on eth_env_set_enetaddr resultPatrick Delaunay
Remove the unnecessary inversion on the eth_env_set_enetaddr() result which only make complex the code of setup_mac_address() and display an invalid value in the associated pr_err. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Marek Vasut <marex@denx.de>
2020-09-09Merge tag 'rpi-next-2020.10.2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi - fixes for bcmgenet - enable USB keyboard for RPi4 32 bit
2020-09-08config: Enable USB Keyboard suuport on RPi4 32 bitMatthias Brugger
Supporting USB keyboards out of the box is both handy for development and production. Notably if u-boot is used to boot into GRUB. This patch adds USB keyboard support for 32 bit RPi4 config. Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-09-08bcmgenet: Add support for rgmii-rxidJason Wessel
The commit 57805f2270c4 ("net: bcmgenet: Don't set ID_MODE_DIS when not using RGMII") needed to be extended for the case of using the rgmii-rxid. The latest version of the Rasbperry Pi4 dtb files for the 5.4 now specify the rgmii-rxid. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Tested-by: Petr Tesarik <ptesarik@suse.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-09-08bcmgenet: fix DMA buffer managementJason Wessel
This commit fixes a serious issue occurring when several network commands are run on a raspberry pi 4 board: for instance a "dhcp" command and then one or several "tftp" commands. In this case, packet recv callbacks were called several times on the same packets, and send function was failing most of the time. note: if the boot procedure is made of a single network command, the issue is not visible. The issue is related to management of the packet ring buffers (producer / consumer) and DMA. Each time a packet is received, the ethernet device stores it in the buffer and increments an index called RDMA_PROD_INDEX. Each time the driver outputs a received packet, it increments another index called RDMA_CONS_INDEX. Between each pair of network commands, as part of the driver 'start' function, previous code tried to reset both RDMA_CONS_INDEX and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from driver side, thus its value was actually not updated, and only RDMA_CONS_INDEX was reset to 0. This was resulting in a major synchronization issue between the driver and the device. Most visible behavior was that the driver seemed to receive again the packets from the previous commands (e.g. DHCP response packets "received" again when performing the first TFTP command). This fix consists in setting RDMA_CONS_INDEX to the same value as RDMA_PROD_INDEX, when resetting the driver. The same kind of fix was needed on the TX side, and a few variables had to be reset accordingly (c_index, tx_index, rx_index). The rx_index and tx_index have only 256 entries so the bottom 8 bits must be masked off. Originated-by: Etienne Dublé <etienne.duble@imag.fr> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Tested-by: Petr Tesarik <ptesarik@suse.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-09-07Prepare v2020.10-rc4Tom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-09-07configs: Resync with savedefconfigTom Rini
Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-09-07Merge tag 'efi-2020-10-rc4' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-10-rc4 Bug fixes are provided in the following areas: * convert file system debug and print messages go log messages * convert UEFI booting messages to log messages * UEFI related code clean up and simplification
2020-09-06efi_selftest: simplify MakefileHeinrich Schuchardt
CONFIG_EFI_LOADER cannot be selected for ARMv7-M CPUs. So don't check it in the Makefile. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-06efi_loader: remove duplicate image size checkHeinrich Schuchardt
The image size is checked in efi_load_pe(). Avoid checking it twice. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-06efi: clean up efi commandHeinrich Schuchardt
* Eliminate superfluous enum value EFI_TABLE_END. * Use correct variable type for the memory type. * Check validity of memory type. * Make efi_build_mem_table static. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-06efi_loader: error message if image not authenticatedHeinrich Schuchardt
Currently if the bootefi command fails due to missing authentication, the user gets no feedback. Write a log message 'Image not authenticated' if LoadImage() fails due to missing authentication. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-06efi_loader: log function in image loaderHeinrich Schuchardt
Use log_err() for error messages. Replace debug() by EFI_PRINT(). Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-06efi_loader: log messages for bootefi commandHeinrich Schuchardt
Write log messages when booting via the bootefi command to allow tracking on the syslog server. Example messages are Booting /snp.efi or Booting /MemoryMapped(0x0,0x4fe00000,0x35a40) Loading image failed Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-06fs: convert error and debug messages to logHeinrich Schuchardt
Use log functions for error and debug messages of the file-system. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-09-04Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvellTom Rini
- Fix SATA issue on Armada 3720 - Enable more SPI NOR chips in espressobin defconfig
2020-09-04defconfig: espressobin: Add support for ISSI SPI flashesKonstantin Porotchkin
Enable support of ISSI SPI flashes found on EspressoBIN boards Change-Id: I6de61c48f108fb4f410f321b9db45887d23212e5 Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/61455 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: Stefan Chulski <stefanc@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
2020-09-04defconfig: espressobin: Include support for Gigadevice SPIKonstantin Porotchkin
Include support for CONFIG_SPI_FLASH_GIGADEVICE for supporting newly produces EspressoBin boards (v7) Change-Id: I5d4b972cbe2ee5a9d52ce9908794ad4e1b59ee3b Signed-off-by: Konstantin Porotchkin <kostap@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/61236 Tested-by: iSoC Platform CI <ykjenk@marvell.com> Reviewed-by: Igal Liberman <igall@marvell.com> Reviewed-by: Stefan Roese <sr@denx.de>
2020-09-04phy: marvell: a3700: add sata comphy on lane 2 with invert optionzachary
- This patch moves sata phy powerup from dedicate phy to compphy and adds invert option for sata powerup routine. Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90 Signed-off-by: zachary <zhangzg@marvell.com> Signed-off-by: Ken Ma <make@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/53601 Reviewed-by: Igal Liberman <igall@marvell.com> Tested-by: Igal Liberman <igall@marvell.com> [a.heider: adapt to mainline] Signed-off-by: Andre Heider <a.heider@gmail.com> Tested-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2020-09-03Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- Mostly DFU fixes and r8152 fixes
2020-09-03Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- SH serial bugfix
2020-09-03Merge branch 'for-tom' of https://github.com/lftan/u-bootTom Rini
- SoCFPGA bugfix
2020-09-03arm: socfpga: soc64: Check FPGA Config status register before bridge resetChee Hong Ang
Instead of querying SDM for FPGA configuration status through mailbox messages, U-Boot now checks System Manager's FPGA Config status register for FPGA configuration status before resetting bridge. Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com> Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
2020-09-02Azure/GitLab: Update to latest Docker containerTom Rini
- New base snapshot - Fix for high UID/GID numbers on a toolchain Signed-off-by: Tom Rini <trini@konsulko.com>
2020-09-01Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86Tom Rini
- Fix parsing of "mtrr list" command - Introduce USE_EARLY_BOARD_INIT option and remove dead codes for most x86 boards
2020-09-01fastboot: getvar: fix partition-size return valueGary Bisson
The size returned by 'getvar partition-size' should be in bytes, not in blocks as fastboot uses that value to generate empty partition when running format [1]. Note that the function was already returning the proper size in bytes for NAND devices (see struct part_info details). [1] https://android.googlesource.com/platform/system/core/+/refs/heads/android10-release/fastboot/fastboot.cpp#1500 Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
2020-09-01fastboot: Fix fastboot reboot fail by changing functions orderyurii.pidhornyi
It was revealed that when the fastboot_tx_write_str function is called without the previously initialized fastboot_func->in_req->complete field, a copy of in_req will be sent to the I/O requests queue without an initialized field. Moving a piece of code with the initializing of the fastboot_func->in_req->complete field above transmit_tx allows to solve this problem. Fixes: 65c96757fe9 "usb: fastboot: Convert USB f_fastboot to shared fastboot" Signed-off-by: yurii.pidhornyi <yurii.pidhornyi@globallogic.com>
2020-09-01f_sdp: Change bInterval of interrupt endpoint to 3Sherry Sun
Since the USB HID limits the maximum bandwidth(3072) for interrupt endpoint transfers, when the bInterval set to 1, we can only support 3 boards to run sdp at the same time. In order to support more boards, change the bInterval of interrupt endpoint to 3, which will not affect the transmission speed. Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01f_sdp: Add EP1_OUT as default data receive pipe in sdpSherry Sun
EP0 has been used to transfer file data in sdp before, but the max packetsize of ep0 is 64 bytes. So in order to improve the file transfer speed, here add the EP1_OUT interrupt endpoint which max packetsize is set to 1024 byte. After testing, it turns out that using ep1out is twice as fast as using ep0 while receiving data in sdp. Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01spl: add g_dnl_get_board_bcd_device_numberPeng Fan
Add g_dnl_get_board_bcd_device_number, the new BCD value is used by uuu to distinguish if the SPL supports the SDPV. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-09-01f_sdp: Support searching and loading FIT or container imagePeng Fan
Add support to f_sdp to search and load iMX8 container image or iMX8M FIT image by new UUU command SDPV. When using the SDPV, the uuu will continue to send out data after first level boot loader used by ROM. This means uuu won't skip to the offset of the second boot loader, and the padding data before second boot loader will be sent out. So we have to search the FIT header or container header in the buffer that SDP received. Also change to more common method to exit f_sdp handler not depending on SPL_FIT_FOUND flag because container loader won't set this. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01f_sdp: Fix wrong usb request sizeYe Li
Because the buffer length of sdp usb request is 65, we have to allocate 65 bytes not 64 bytes. Otherwise there is potential buffer overflow. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-09-01f_sdp: Add high speed endpoint descriptorYe Li
Add HS endpoint descriptor for SDP. So that we can use high speed endpoint, and the SDP device can send packet with 512 byte size. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
generated by cgit (git 2.34.1) at 2024-12-23 18:25:19 +0000