summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-11-08powerpc/85xx: verify the current address of CCSR before relocating itTimur Tabi
Verify that CCSR is actually located where it is supposed to be before we relocate it. This is useful in detecting U-Boot configurations that are broken (e.g. an incorrect value for CONFIG_SYS_CCSRBAR_DEFAULT). If the current value is wrong, we enter an infinite loop, which is handy for debuggers. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08powerpc/85xx: add some missing sync instructions in the CCSR relocation codeTimur Tabi
Calls to tlbwe and tlbsx should be preceded with an isync/msync pair. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08powerpc/85xx: fix some comments in the CCSR relocation codeTimur Tabi
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08powerpc/85xx: fix definition of MAS register macrosTimur Tabi
Some of the MAS register macros do not protect the parameter with parentheses, which could cause wrong values if the parameter includes operators. Also fix the definition of TSIZE_TO_BYTES() so that it actually uses the parameter. This hasn't caused any problems to date because the parameter was always been 'tsize'. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08powerpc/mpc8548cds: Fix network initializationchenhui zhao
Add board_eth_init(). PCIe network card is also supported. Put RGMII init after tsec_eth_init(). Skip initializing eTSEC3 and eTSEC4 with Carrier boards prior to ver 1.3. Signed-off-by: Ebony Zhu Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
2011-11-08powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129chenhui zhao
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early verion silicons. This workaround detects if the eTSEC Rx logic is properly initialized, and reinitialize the eTSEC Rx logic. Signed-off-by: Gong Chen <g.chen@freescale.com> Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08powerpc/QorIQ: fix network frame manager TBI PHY address settingsRoy Zang
TBI PHY address (TBIPA) register has been set in general frame manager phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c So remove the duplicate code on QorIQ frame manager Ethernet related platforms, which include Hydra board, P4080DS board and P2041rdb board. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Cc: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08Merge branch 'master' of git://git.denx.de/u-boot-mpc83xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-mpc83xx: powerpc/mpc83xx: Add 33.33MHz support for mpc8360emds powerpc/mpc83xx: Add 512MB DDR support for mpc8360emds mpc83xx: Rename CONFIG_SYS_DDR_CONFIG and cleanup DDR csbnds code mpc83xx: Cleanup usage of LBC constants mpc83xx: Cleanup usage of DDR constants mpc83xx: Cleanup usage of BAT constants mpc83xx: cosmetic: vme8349.h checkpatch compliance mpc83xx: cosmetic: ve8313.h checkpatch compliance mpc83xx: cosmetic: sbc8349.h checkpatch compliance mpc83xx: cosmetic: mpc8308_p1m.h checkpatch compliance mpc83xx: cosmetic: kmeter1.h checkpatch compliance mpc83xx: cosmetic: TQM834x.h checkpatch compliance mpc83xx: cosmetic: SIMPC8313.h checkpatch compliance mpc83xx: cosmetic: MVBLM7.h checkpatch compliance mpc83xx: cosmetic: MPC837XERDB.h checkpatch compliance mpc83xx: cosmetic: MPC837XEMDS.h checkpatch compliance mpc83xx: cosmetic: MPC8360ERDK.h checkpatch compliance mpc83xx: cosmetic: MPC8360EMDS.h checkpatch compliance mpc83xx: cosmetic: MPC8349ITX.h checkpatch compliance mpc83xx: cosmetic: MPC8349EMDS.h checkpatch compliance mpc83xx: cosmetic: MPC832XEMDS.h checkpatch compliance mpc83xx: cosmetic: MPC8323ERDB.h checkpatch compliance mpc83xx: cosmetic: MPC8315ERDB.h checkpatch compliance mpc83xx: cosmetic: MPC8313ERDB.h checkpatch compliance mpc83xx: cosmetic: MPC8308RDB.h checkpatch compliance mpc83xx: cosmetic: MERGERBOX.h checkpatch compliance mpc83xx: Fix ipic structure definition powerpc, mpc83xx: add DDR SDRAM Timing Configuration 3 definitions cosmetic, powerpc, mpc83xx: checkpatch cleanup powerpc/83xx: move km 83xx specific i2c code to km83xx_i2c mpc83xx: fix global timer structure definition
2011-11-07powerpc/mpc83xx: Add 33.33MHz support for mpc8360emdsJerry Huang
The new MPC8360EMDS board changes the oscillator to 33.33MHz in order to support QE 500MHz since 2008. Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-11-08Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk
* 'master' of git://git.denx.de/u-boot-arm: Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board arm: jadecpu: Readd MACH_TYPE_JADECPU at91: defined mach-types for otc570 board in board config file at91: defined mach-types for meesc board in board config file mx31pdk: Enable D and I caches ehci-mxc: remove incorrect comment README: Fix supported i.MX SoC list for CONFIG_MXC_SPI mx53: Turn off child clocks before reconfigure perclk_root qong: enable support for compressed images imx: imx31_phycore.h: fix checkpatch warnings vision2: Remove unused get_board_rev function mx53smd: Remove unused get_board_rev function mx53ard: Remove unused get_board_rev function mx53evk: Remove unused get_board_rev function mx53evk: Add RTC support mx53loco: Remove unused get_board_rev function mx53evk: Remove unneeded '1' from mx53evk.h OMAP3: mvblx: Initial support for mvBlueLYNX-X ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE omap3: mem: Move comments next to definitions omap3: mem: Clean-up whitespaces omap3: mem: Define and use common macros Davinci: ea20: added PREBOOT to configuration Davinci: ea20: added I2C support Davinci: ea20: added video support VIDEO: davinci: add framebuffer to da8xx ARM: Davinci: added missing registers to hardware.h Davinci: ea20: add gpios for LCD backlight control Davinci: ea20: add gpio for keeping power on in board_late_init Davinci: ea20: Add default U-Boot environment Davinci: ea20: Add early init to get early output from console Davinci: ea20: Add NAND support Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console Davinci: ea20: set console on UART0 arm, davinci: add cam_enc_4xx support arm926ejs, davinci: add missing spi defines for dm365 arm926ejs, davinci: add cpuinfo for dm365 arm, davinci: add lowlevel function for dm365 soc arm, davinci: add header files for dm365 spl, nand: add 4bit HW ecc oob first nand_read_page function arm, davinci: add support for new spl framework spl: add option for adding post memory test to the SPL framework net, davinci_emac: make clock divider in MDIO control register configurable arm, usb, davinci: make USBPHY_CTL register configurable usb, davinci: add enable_vbus() weak function omap3evm: fix errors caused by multiple definitions omap3evm: Add (quick) configuration for NAND only omap3evm: Add (quick) configuration for MMC/SD only omap3evm: move common config options to new file omap3evm: Prepare to split configuration omap3evm: Reorder related config options omap/spl: actually enable the console davinci_emac: compilation fix, phy is array now omap3evm: Set environment variable 'ethaddr' arm, arm926: fix missing symbols in NAND_SPL mode arm, davinci: Add function lpsc_syncreset() arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD arm/km: portl2 environment address update to P1B arm/km: adapt bootcounter evaluation arm/km: enable jffs2 cmds arm/km: trigger reconfiguration for the Xilinx FPGA arm/km: add boardid and hwkey to kernel command line ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards netspace_v2: enable I2C EEPROM support netspace_v2: fix SDRAM configuration armada100: define CONFIG_SYS_CACHELINE_SIZE pantheon: define CONFIG_SYS_CACHELINE_SIZE kirkwood: define CONFIG_SYS_CACHELINE_SIZE kirkwood: drop empty asm-offsets.s file arm/km/mgcoge3un: enhance "waitforne" feature arm/km: add variable waitforne to mgcoge3un gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared ARM: dreamplug: fix compilation ARM: DockStar: fix compilation ARM: netspace_v2: fix warnings am335x: Drop board_sysinfo struct am335x: Temporarily add MACH_TYPE define misc:pmic:samsung Enable PMIC driver at C210 Universal target dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target smdkv310: use macro for mmc data read function address smdkv310: use spl framework for mmc spl SMDKV310: use get_ram_size() to validate dram size SMDKV310: Initialize board id using CONFIG_MACH_TYPE ORIGEN : use absolute paths and fix tool naming ORIGEN : enable device tree support MX25: tx25: Fix building due to missing MACH_TYPE mx31: Add board support for HALE TT-01 mx31: add ESD control registers mx31: define pins and init for UART2 and CSPI3 MX35: add support for flea3 board MX51: vision2: add MACH_TYPE in config file vision2: Remove unused header file mx51evk: Remove unused get_board_rev function mx51evk: Remove unneeded '1' from mx51evk.h I2C: Fix mxc_i2c.c problem on imx31_phycore mx35pdk: Add RTC support mx51evk: Use GPIO API for configuring the IOMUX mx51evk: Add RTC support rtc: Make mc13783-rtc driver generic qong: remove unneeded IOMUX settings qong: Use mx31_set_gpr to setup USBH2 pins mx31: Introduce mx31_set_gpr function mx31pdk: Add MC13783 PMIC support qong: remove unneeded "1" from qong.h misc: pmic: fix regression in pmic_fsl.c (SPI) mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME MX35: Drop unnecessary prototypes from imx-regs.h I2C: added I2C-2 and I2C-3 to MX35 MX35: factorize common assembly code MX35: add reset cause as provided by other i.MX MX35: add pins definition for UART3 MX35: added ESDC structure to imx-regs
2011-11-08Merge branch 'master' of git://git.denx.de/u-boot-coldfireWolfgang Denk
* 'master' of git://git.denx.de/u-boot-coldfire: ColdFire: The EB+MCF-EV123 boards config update ColdFire: Fix the compile issue for M52277 ColdFire:Moving the remaining coldfire boards to boards.cfg
2011-11-08Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk
* 'master' of git://git.denx.de/u-boot-i2c: Powerpc/i2c: Use the same initialize codes
2011-11-07board/siemens/SCM/scm.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: scm.c: In function 'config_scoh_cs': scm.c:400:16: warning: variable 'tmp' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/funkwerk/vovpn-gw/vovpn-gw.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: vovpn-gw.c: In function 'misc_init_r': vovpn-gw.c:266:16: warning: variable 'temp' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/freescale/mpc8266ads/mpc8266ads.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: mpc8266ads.c: In function 'initdram': mpc8266ads.c:278:9: warning: variable 'spd_size' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/freescale/mpc8266ads/mpc8266ads.c: CodingStyle cleanupWolfgang Denk
Make (mostly) checkpatch clean. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Rune Torgersen <runet@innovsys.com>
2011-11-07board/sacsng/sacsng.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: sacsng.c: In function 'initdram': sacsng.c:180:9: warning: variable 'spd_size' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
2011-11-07board/sacsng/sacsng.c: CodingStyle cleanupWolfgang Denk
Make (mostly) checkpatch clean. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
2011-11-07board/rpxsuper/flash.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: flash.c: In function 'flash_init': flash.c:52:19: warning: variable 'size' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/rpxsuper/flash.c: minimal CodingStyle cleanupWolfgang Denk
Really minimal and local, just good enough to make checkpatch not complain about the changes in the following commit. Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/ids8247/ids8247.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: ids8247.c: In function 'initdram': ids8247.c:284:14: warning: variable 'lsize' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
2011-11-07board/hymod/input.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: input.c: In function 'hymod_get_ethaddr': input.c:79:10: warning: variable 'ea' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Murray Jensen <Murray.Jensen@csiro.au>
2011-11-07board/ep82xxm/ep82xxm.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: ep82xxm.c: In function 'initdram': ep82xxm.c:233:16: warning: variable 'ramtmp' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/gw8260/flash.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: flash.c: In function 'flash_init': flash.c:81:16: warning: variable 'size' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Oliver Brown <obrown@adventnetworks.com>
2011-11-07board/gw8260/flash.c: minimal CodingStyle cleanupWolfgang Denk
Really minimal and local, just good enough to make checkpatch not complain about the changes in the following commit. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Oliver Brown <obrown@adventnetworks.com>
2011-11-07board/cogent/flash.c: Fix GCC 4.6 buiild warningWolfgang Denk
Fix: flash.c: In function 'flash_init': flash.c:295:16: warning: variable 'fip' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Murray Jensen <Murray.Jensen@csiro.au>
2011-11-07arch/powerpc/cpu/mpc8260/spi.c: Fix GCC 4.6 build warningsWolfgang Denk
Fix: spi.c: In function 'spi_init_r': spi.c:279:22: warning: variable 'cp' set but not used [-Wunused-but-set-variable] spi.c: In function 'spi_xfer': spi.c:361:22: warning: variable 'cp' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07common/cmd_flash.c: Fix GCC 4.6 build warningsWolfgang Denk
Fix: cmd_flash.c:355:32: warning: 'info' may be used uninitialized in this function [-Wuninitialized] cmd_flash.c:354:10: warning: 'sect_first' may be used uninitialized in this function [-Wuninitialized] cmd_flash.c:354:10: warning: 'sect_last' may be used uninitialized in this function [-Wuninitialized] cmd_flash.c: In function 'do_protect': cmd_flash.c:540:9: warning: 'info' may be used uninitialized in this function [-Wuninitialized] cmd_flash.c:538:9: warning: 'sect_first' may be used uninitialized in this function [-Wuninitialized] cmd_flash.c:538:9: warning: 'sect_last' may be used uninitialized in this function [-Wuninitialized] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07drivers/net/rtl8139.c: Fix GCC 4.6 build warningsWolfgang Denk
Fix: rtl8139.c: In function 'rtl8139_probe': rtl8139.c:256:15: warning: variable 'fullduplex' set but not used [-Wunused-but-set-variable] rtl8139.c:256:6: warning: variable 'speed10' set but not used [-Wunused-but-set-variable] rtl8139.c: In function 'rtl_transmit': rtl8139.c:419:16: warning: variable 'txstatus' set but not used [-Wunused-but-set-variable] Change code to use new debug macros; also fix the new errors and warnigns popping up now, like "error: 'to' undeclared" and some "warning: format '%X' expects argument of type 'unsigned int', but argument X has type 'long unsigned int'" Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/linkstation/ide.c: Fix GCC 4.6 build warningsWolfgang Denk
Fix: ide.c: In function 'ide_preinit': ide.c:69:21: warning: array subscript is above array bounds [-Warray-bounds] ide.c:69:21: warning: array subscript is above array bounds [-Warray-bounds] ide.c:70:17: warning: array subscript is above array bounds [-Warray-bounds] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
2011-11-07drivers/net/rtl8169.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: rtl8169.c: In function 'rtl_init': rtl8169.c:742:13: warning: variable 'printed_version' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/mousse/flash.c: Fix GCC 4.6 buil warningsWolfgang Denk
Fix: flash.c: In function 'flash_erase': flash.c:780:18: warning: variable 'l_sect' set but not used [-Wunused-but-set-variable] flash.c:779:11: warning: variable 'addr' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/etin/kvme080/multiverse.c: Fix GCC 4.6 build warning.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Sangmoon Kim <dogoil@etinsys.com>
2011-11-07drivers/net/pcnet.c: Change debug code to fix build warningWolfgang Denk
Fix: pcnet.c: In function 'pcnet_probe': pcnet.c:247:8: warning: variable 'chipname' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Wolfgang Grandegger <wg@denx.de>
2011-11-07board/alaska/flash.c: Fix GCC 4.6 build warningsWolfgang Denk
Fix: flash.c: In function 'flash_erase': flash.c:409:21: warning: variable 'last' set but not used [-Wunused-but-set-variable] flash.c:408:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] flash.c: In function 'write_data': flash.c:669:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] flash.c: In function 'write_data_block': flash.c:709:6: warning: variable 'flag' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07arch/powerpc/lib/bat_rw.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: bat_rw.c: In function 'write_bat': bat_rw.c:38:6: warning: variable 'batn' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Andy Fleming <afleming@gmail.com>
2011-11-07mpc8220/i2c.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: i2c.c: In function 'wait_for_bb': i2c.c:109:16: warning: variable 'temp' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
2011-11-07mpc8260/i2c.c: replace PRINTD() by debug()Wolfgang Denk
This also fixes some GCC 4.6 build warnings like: i2c.c: In function 'i2c_init': i2c.c:221:26: warning: variable 'txbd' set but not used [-Wunused-but-set-variable] i2c.c:221:19: warning: variable 'rxbd' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
2011-11-07mpc8260/i2c.c: CodingStyle cleanupWolfgang Denk
Make (mostly) checkpatch clean (don't convert to use I/O accessors yet, so there will be "Use of volatile is usually wrong" warnings left. Also accept some other harmless checkpatch warnings. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
2011-11-07mpc8220/fec.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: fec.c: In function 'mpc8220_fec_recv': fec.c:733:8: warning: variable 'frame' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07common/cmd_i2c.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: cmd_i2c.c: In function 'do_i2c_add_bus': cmd_i2c.c:1212:19: warning: variable 'dev' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Heiko Schocher <hs@denx.de>
2011-11-07board/tqc/tqm8272/tqm8272.c: Fix GCC 4.6 build warning:Wolfgang Denk
Fix: tqm8272.c: In function 'initdram': tqm8272.c:462:14: warning: variable 'lsize' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07mpc8260/speed.c: Fix GCC 4.6 build warningsWolfgang Denk
Fix: speed.c: In function 'get_clocks': speed.c:113:30: warning: variable 'cpmdf' set but not used [-Wunused-but-set-variable] speed.c:113:23: warning: variable 'busdf' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07TQM850M: Add missing CONFIG_BOOTDELAYWolfgang Denk
This also fixes a build warning: main.c: In function 'main_loop': main.c:311:16: warning: variable 'bootlimit' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/svm_sc8xx/flash.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: flash.c: In function 'write_word': flash.c:542:15: warning: variable 'last' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/svm_sc8xx/flash.c: CodingStyle cleanupWolfgang Denk
Make (mostly) checkpatch clean (don't convert to use I/O accessors yet, so there will be "Use of volatile is usually wrong" warnings left. Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/svm_sc8xx/svm_sc8xx.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: svm_sc8xx.c: In function 'checkboard': svm_sc8xx.c:83:6: warning: variable 'board_type' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/rbc823/flash.c: Fix flash initalizationWolfgang Denk
The RBC823 has only one NOR flash bank. Remove all code trying to deal with a second bank. This also fixes a number of GCC 4.6 build warnings: flash.c: In function 'flash_init': flash.c:62:12: warning: array subscript is above array bounds [-Warray-bounds] flash.c:63:12: warning: array subscript is above array bounds [-Warray-bounds] flash.c:66:12: warning: array subscript is above array bounds [-Warray-bounds] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/rbc823/flash.c: CodingStyle cleanupWolfgang Denk
Make (mostly) checkpatch clean (don't convert to use I/O accessors yet, so there will be "Use of volatile is usually wrong" warnings left. Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-11-07board/fads/fads.c: Fix GCC 4.6 build warningWolfgang Denk
Fix: fads.c: In function 'initdram': fads.c:606:7: warning: variable 'base' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
generated by cgit (git 2.34.1) at 2024-12-27 20:53:11 +0000