summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2007-05-08add: Microblaze V5 exception handlingMichal Simek
2007-05-08add: FSL control read and writeMichal Simek
2007-05-08Merge git://www.denx.de/git/u-bootMichal Simek
Conflicts: include/asm-microblaze/microblaze_intc.h include/linux/stat.h
2007-05-07new: USE_MSR_INTR supportMichal Simek
2007-05-07fix: read and write MSR - repair number of parametersMichal Simek
2007-05-07new: fsl interrupt supportMichal Simek
FSL_Has_data is connected to INTC.
2007-05-07fix: interrupt handlerMichal Simek
remove asm code
2007-05-07fix: remove asm codeMichal Simek
2007-05-07fix: clean interruptMichal Simek
2007-05-07fix: interrupt handler for multiple sourcesMichal Simek
2007-05-07new: add writing to msr registerMichal Simek
2007-05-055xxx: write MAC address to mac-address and local-mac-addressTimur Tabi
Some device trees have a mac-address property, some have local-mac-address, and some have both. To support all of these device trees, ftp_cpu_setup() should write the MAC address to mac-address and local-mac-address, if they exist. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Grant Likely <grant.likely@secretlab.ca>
2007-05-05[PATCH] Use PVR to distinguish MPC5200B from MPC5200 in boot messageGrzegorz Wianecki
MPC5200B systems are incorrectly reported as MPC5200 in U-Boot start-up message. Use PVR to distinguish between the two variants, and print proper CPU information. Signed-off-by: Grzegorz Wianecki <grzegorz.wianecki@gmail.com> Signed-off-by: Bartlomiej Sieka <tur@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2007-05-05[PATCH] simplify silent consoleLadislav Michl
Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Acked-by: Stefan Roese <sr@denx.de>
2007-05-05[PATCH] Avoid assigning PCI resources from zero addressSergei Shtylyov
If a PCI IDE card happens to get a zero address assigned to it, the Linux IDE core complains and IDE drivers fails to work. Also, assigning zero to a BAR was illegal according to PCI 2.1 (the later revisions seem to have excluded the sentence about "0" being considered an invalid address) -- so, use a reasonable starting value of 0x1000 (that's what the most Linux archs are using). Alternatively, one might have fixed the calls to pci_set_region() individually (some code even seems to have taken care of this issue) but that would have been a lot more work. :-) Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: Stefan Roese <sr@denx.de>
2007-05-05[patch] setenv(...) can delete environmentalvariablesJeffrey Mann
update setenv() function so that entering a NULL value for the variable's value will delete the environmental variable Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com> Acked-by: Stefan Roese <sr@denx.de>
2007-05-05[patch] use unsigned char in smc91111 driver for macMike Frysinger
the v_mac variable in the smc91111 driver is declared as a signed char ... this causes problems when one of the bytes in the MAC is "signed" like 0xE0 because when it gets printed out, you get a display like: 0xFFFFFFE0 and that's no good Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2007-05-05new: FSL and MSR support #2Michal Simek
2007-05-05new: FSL and MSR supportMichal Simek
2007-05-05Coding stylke cleanup; update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-05-05Merge with /home/wd/git/u-boot/custodian/u-boot-ppc4xxWolfgang Denk
2007-05-05Add STX GP3 SSA board to MAKEALL script; update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-05-05Merge with /home/wd/git/u-boot/custodian/u-boot-mpc85xxWolfgang Denk
2007-05-05Make "file" command happy with some config.mk files; update CHANGELOGWolfgang Denk
2007-05-05Merge with /home/wd/git/u-boot/custodian/u-boot-nand-flashWolfgang Denk
2007-05-05Merge with /home/wd/git/u-boot/custodian/u-boot-mpc86xxWolfgang Denk
2007-05-05Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-05-05ppc4xx: Detect if the sysclk on Sequoia is 33 or 33.333 MHzJeffrey Mann
The AMCC Secquoia board has been changed in a new revision from using a 33.000 MHz clock to a 33.333 MHz system clock. A bit in the CPLD indicates the difference. This patch reads that bit and uses the correct clock speed for the board. This code is backward compatable will all prior boards. All prior boards will be read as 33.000. Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com> Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-05ppc4xx: Sequoia: Remove cpu/ppc4xx/speed.c from NAND bootingStefan Roese
Using cpu/ppc4xx/speed.c to calculate the bus frequency is too big for the 4k NAND boot image so define bus_frequency to 133MHz here which is save for the refresh counter setup. Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-05Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-05-05NAND: Wrong calculation of page number in nand_block_bad()Thomas Knobloch
In case that there is no memory based bad block table available the function nand_block_checkbad() in drivers/mtd/nand/nand_base.c will call nand_block_bad() directly. When parameter 'getchip' is set to zero, nand_block_bad() will not right shift the offset to calculate the correct page number. Signed-off-by: Thomas Knobloch <knobloch@siemens.com> Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-04Fix initrd length corruption in bootm command.Wolfgang Denk
When using FDT Images, the length of an inital ramdisk was overwritten (bug introduced by commit 87a449c8, 22 Aug 2006). Patches by Timur Tabi & Johns Daniel. Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-05-03Update board configuration for STX GP3SSA board:Wolfgang Denk
Enable hush shell, environment in flash rather in EEPROM, more user-friendly default environment, etc. The simple EEPROM environment can be selected easily in the board config file. Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-05-03Cleanup STX GP3SSA code; fix build and compile problems.Wolfgang Denk
2007-05-03Add support for STX GP3SSA (stxssa) BoardDan Malek
Signed-off-by Dan Malek, <dan@embeddedalley.com>
2007-05-02Cleaned up some 85xx PCI bugsAndy Fleming
* Cleaned up the CDS PCI Config Tables and added NULL entries to the end * Fixed PCIe LAWBAR assignemt to use the cpu-relative address * Fixed 85xx PCI code to assign powar region sizes based on the config values (rather than hard-coding them) * Fixed the 8548 CDS PCI2 IO to once again have 0 as the base address Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-05-02Add support for the 8568 MDS boardAndy Fleming
This included some changes to common files: * Add 8568 processor SVR to various places * Add support for setting the qe bus-frequency value in the dts * Add the 8568MDS target to the Makefile Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-05-02Add support for treating unknown PHYs as generic PHYs.David Updegraff
When bringing up u-boot on new boards, PHY support sometimes gets neglected. Most PHYs don't really need any special support, though. By adding a generic entry that always matches if nothing else does, we can provide support for "unsupported" PHYs for the tsec. The generic PHY driver supports most PHYs, including gigabit. Signed-off-by: David Updegraff <dave@cray.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-05-01Conditionalize 8641 Rev1.0 MCM workaroundsJames Yang
Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-05-01Rewrote picos_to_clk() to avoid rounding errors.James Yang
Clarified that conversion is to DRAM clocks rather than platform clocks. Made function static to spd_sdram.c. Signed-off-by: James Yang <James.Yang@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-04-29Merge with git://www.denx.de/git/u-boot.gitStefan Roese
2007-04-29Merge with /home/stefan/git/u-boot/u-boot-ppc4xxStefan Roese
2007-04-29ppc4xx: Bamboo: Use current NAND driver and *not* the legacy driverStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2007-04-24[PATCH] MTD partition support, JFFS2 supportMichal Simek
2007-04-24ppc4xx: setup 440EPx/GRx ZMII/RGMII bridge depending on PFC register content.Matthias Fuchs
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2007-04-23Reworked 85xx speed detection codeAndy Fleming
Changed the code to read the registers and calculate the clock rates, rather than using a "switch" statement. Idea from Andrew Klossner <andrew@cesa.opbu.xerox.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-04-23Enable 8544 supportAndy Fleming
* Add support to the Makefile * Add 8544 configuration support to the tsec driver * Add 8544 SVR numbers to processor.h Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-04-23Support 1G size on 8548Andy Fleming
e500v2 and newer cores support 1G page sizes. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-04-23Changed BOOKE_PAGESZ_nGB to BOOKE_PAGESZ_nGAndy Fleming
The other pagesz constants use one letter to specify order of magnitude. Also change the one reference to it in mpc8548cds/init.S Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-04-23Only set ddrioovcr for 8548 rev1.Andy Fleming
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
generated by cgit (git 2.34.1) at 2024-12-26 20:54:11 +0000