| Age | Commit message (Collapse) | Author |
|---|
|
Add do_bridge_reset() function for Arria 10, it is required by misc.c.
arch/arm/mach-socfpga/built-in.o: In function `do_bridge':
arch/arm/mach-socfpga/misc.c:221: undefined reference to `do_bridge_reset'
make[1]: *** [u-boot] Error 1
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add build support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Conflicts:
arch/arm/Kconfig
arch/arm/mach-socfpga/Kconfig
|
|
Add socdk board support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add DDR support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add timer support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Add SPL driver support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Restructure the SPL so each devices such as CV, A10 and S10
will have their own dedicated SPL file. SPL file determine
the HW initialization flow which is device specific
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Add MMU memory mapping table for Stratix SoC.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Add mailbox support for Stratix SoC
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Add misc support such as EMAC and cpu info printout for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Move bridge command to misc common driver, in preparation to used by
other platforms.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
Use "%p" to print cmdbuf.
Compilation warning as below:
CC spl/drivers/spi/cadence_qspi_apb.o
LD spl/lib/built-in.o
drivers/spi/cadence_qspi_apb.c: In function ‘cadence_qspi_apb_indirect_write_setup’:
drivers/spi/cadence_qspi_apb.c:696:18: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
cmdlen, (unsigned int)cmdbuf);
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Use "%zu" for size_t data type.
Compilation warning as below:
In file included from include/linux/bug.h:7:0,
from include/common.h:26,
from drivers/spi/cadence_qspi.c:8:
drivers/spi/cadence_qspi.c: In function ‘cadence_spi_xfer’:
drivers/spi/cadence_qspi.c:211:8: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
debug("%s: len=%d [bytes]\n", __func__, data_bytes);
^
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
#define pr_fmt(fmt) fmt
^~~
include/log.h:142:2: note: in expansion of macro ‘debug_cond’
debug_cond(_DEBUG, fmt, ##args)
^~~~~~~~~~
drivers/spi/cadence_qspi.c:211:2: note: in expansion of macro ‘debug’
debug("%s: len=%d [bytes]\n", __func__, data_bytes);
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
By checking ubifs source code, s_instances parameter is not
used anymore. So, set this parameter and the associated source
code under __UBOOT__ compilation.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
When trying to attach an UBI MTD partition via "ubi part", it may happen
that the MTD partition defined in U-Boot (via mtdparts) is not big
enough than the one, where the UBI device has been created on. This
may lead to errors, which are not really descriptive to debug and
solve this issue, like:
ubi0 error: vtbl_check: too large reserved_pebs 1982, good PEBs 1020
ubi0 error: vtbl_check: volume table check failed: record 0, error 9
or:
ubi0 error: init_volumes: not enough PEBs, required 1738, available 1020
ubi0 error: ubi_wl_init: no enough physical eraseblocks (-718, need 1)
ubi0 error: ubi_attach_mtd_dev: failed to attach mtd1, error -12
Lets add an additional message upon attach failure, to aid the U-Boot
user to solve this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
|
|
When using static volumes, the file size stored in the volume is
determined at runtime. Currently the ubi command prints the file
size specified on the console, which leads to a rather confusing
series of messages:
# ubi read ${fdt_addr_r} testvol
Read 0 bytes from volume testvol to 82000000
No size specified -> Using max size (179924992)
Make sure to print the actual size read in any case:
# ubi read ${fdt_addr_r} testvol
No size specified -> Using max size (179924992)
Read 179924992 bytes from volume testvol to 82000000
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
|
|
|
|
|
|
In the device tree, the address for the led is located
in the parent node (for exemple leds), not in the led node
(for exemple led@0).
The commit "led: bcm6328: convert to use live dt"
(sha1: 899455176058d673887a762aa38853188a030af4)
change this behaviour and read the address in the led node.
We fix this by reading the base address for led
in the parent node.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
In the device tree, the address for cpu is located in
the node "cpus", not in the cpu node (for exemple cpu@0).
So when probing cpu, the cpu address must be read in the
cpu parent.
The commit "cpu: bmips: convert to use live dt"
(sha1: c444afbbefa103d567f197393d39ec0fcca21a0c)
change this behaviour and read the address in the
cpu node when probing cpu.
We fix this by reading the address in the cpu parent.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
Now that Travis CI is building with gcc-7.3.0, we can add
build coverage for all combinations of MIPS Release 6
instruction sets (MIPS32, MIPS64, Big Endian, Little Endian).
Add mew default configs for Boston board for all MIPS Release 6
variants.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Since commit f916757300 (imx: Create distinct pre-processed mkimage
config files), *.cfgtmp files are no longer generated. There is no need
to remove them on the 'clean' target anymore.
Rename the .gitignore glob to *.cfgout.
Cc: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
|
|
When generating timestamps in signatures, use imagetool_get_source_date()
so we can be overridden by SOURCE_DATE_EPOCH to generate reproducible
images.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromum.org>
|
|
So we can use imagetool_get_source_date() from callers who do not have
the image tool params struct, just pass in the command name for the error
message.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromum.org>
|
|
In ARM 64-bits, memory size can be supported is more than 4GB,
hence increasing save array is needed to cope with testing larger memory.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
|
|
This patch moves CONFIG_MP to Kconfig
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Commit e19b0fb4851f (kbuild: generate u-boot.cfg as a byproduct of
include/autoconf.mk) removed the use of the cpp_cfg macro in Makefile,
but forgot to remove its definition.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Newer kernels have moved from ttyO0 to ttyS0, and when booting
it drops a notice:
WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
This ensures that you still see kernel messages. Please
update your kernel commandline.
This patch updates the console to use ttyS0 and eliminate the
chatter.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Typically init_scsi() does not output anything. So initr_scsi() should
provide a \n or we may see borked output like
SCSI: Net: No ethernet found.
as observed with sandbox_defconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The omap_gpio driver has a TODO that says when every board is converted
to DM and DT, the omap_gpio_bind can stop using calloc and switch
to auto-alloc.
This patch converts this driver to auto-calloc when DT is enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
The hashed-strings signature property includes two uint32_t values.
The first is unneeded as there should never be a start offset into the
strings region. The second, the size, is needed because the added
signature node appends to this region.
See tools/image-host.c, where a static 0 value is used for the offset.
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This adds a new config value FIT_SIGNATURE_MAX_SIZE, which controls the
max size of a FIT header's totalsize field. The field is checked before
signature checks are applied to protect from reading past the intended
FIT regions.
This field is not part of the vboot signature so it should be sanity
checked. If the field is corrupted then the structure or string region
reads may have unintended behavior, such as reading from device memory.
A default value of 256MB is set and intended to support most max storage
sizes.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
|
|
Verification of hashes needs to take place before any image post
processing, thus matching full FIT image processing.
This allows mechanisms such as encryption be applied to images
prior to fit generation at the spl level.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
|
|
Remove empty #ifdef/#ifndef..#endif blocks where the configuration they
guarded has been completely removed.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
Move the FPGA loading from IS_ENABLED(CONFIG_SPL_OS_BOOT) &&
IS_ENABLED(CONFIG_SPL_GZIP) conditional. The FPGA loading can
be used without OS loading and GZIP support in SPL. This issue
was most likely induced by some merge conflict, so fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
|
|
Handle the case where the full fitImage support is enabled. In this
case, the whole fitImage must be loaded up front as some parts of the
fitImage code require memory-mapped access to the entire fitImage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
|
|
Handle the case where the full fitImage support is enabled. In this
case, the whole fitImage must be loaded up front as some parts of the
fitImage code require memory-mapped access to the entire fitImage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
|
|
Rather than verifying configuration signature of the configuration node
containing the kernel image types, verify all configuration nodes, even
those that do not contain kernel images. This is useful when the nodes
contain ie. standalone OSes or U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The openssl command specified in test_with_algo() ultimately ends up
being run by RunAndLog::run(), which uses it to construct a Popen object
with the default shell=False. The stderr redirect in the command is
therefore simply passed to openssl as an argument. With at least openssl
1.1.0f this causes openssl, and therefore test_vboot, to fail with:
genpkey: Use -help for summary.
Exit code: 1
Any stderr output ought to be captured & stored in the RunAndLog
object's output field and returned from run() via run_and_log() to
test_with_algo() which then ignores it anyway, so we can drop the
shell-like redirection with no ill effects. With this fix test_vboot now
passes for me.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
In python 3.x the file() function has been removed. Use open() instead,
which works on both python 2.x & 3.x, and is described as the preferred
method of opening a file by python 2.x documentation anyway.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
The read_file() function in test_fit is used with files that are not
text files, as well as some that are. It is never used in a way that
requires it to decode text files to characters, so open all files in
binary mode such that read() doesn't attempt to decode characters for
files which are not text files.
Without this test_fit fails on python 3.x when reading an FDT in
run_fit_test() with:
UnicodeDecodeError: 'utf-8' codec can't decode byte 0xd0 in position
0: invalid continuation byte
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
In python 3.x the configparser module is named with all lower case.
Import it as such in order to avoid errors when running on python 3.x,
and fall back to the CamelCase version in order to keep working with
python 2.x.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
In python 3.x the xrange() function has been removed, and range()
returns an iterator much like Python 2.x's xrange(). Simply use range()
in place of xrange() in order to work on both python 2.x & 3.x. This
will mean a small cost on python 2.x since range() will return a list
there rather than an iterator, but the cost should be negligible.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
In python 3.x print must be called as a function rather than used as a
statement. Update uses of print to the function call syntax in order to
be python 3.x safe.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
|
|
|
|
Add code to reset all reset signals as in Ethernet DT node. A reset
property is an optional feature, so only print out a warning and do not
fail if a reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Add code to reset all reset signals as in serial DT node. A reset
property is an optional feature, so do not fail if a reset property is
not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add code to reset all reset signals as in mmc DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Change to use CONFIG_IS_ENABLED(DM_RESET), so this can work in SPL
build (CONFIG_SPL_DM_RESET) and U-boot build (CONFIG_DM_RESET).
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
