| Age | Commit message (Collapse) | Author |
|---|
|
Reusing the loadaddr to load the boot script breaks some of the logic we
want to have around the bootscript/FIT load addresses. Making a dedicated
bootscript address allows us to differentiate the bootscript load address
from the Linux Kernel or OPTEE load address, thus ensuring that no matter
what the load sequence the bootscript and Kernel/OPTEE binary load
addresses do not conflict.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
|
|
When obtaining the bootscript from a FIT image we need to specify the name
of the bootscript as defined inside of the FIT.
This patch makes a define that appends a "bootscr" parameter to the source
command when compiling up in FIT mode on warp7.
An environment variable is supplied to enable others to use a different
name than "bootscr" as the image name of the boot script in their FIT.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
|
|
This patch switches on FIT verification of boot.scr. After this commit your
boot.scr must be in the FIT format.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
|
|
BD71837 and BD71847 is PMIC intended for powering single-core,
dual-core, and quad-core SoC’s such as NXP-i.MX 8M. BD71847
is used for example on NXP imx8mm EVK.
Add regulator driver for ROHM BD71837 and BD71847 PMICs.
BD71837 contains 8 bucks and 7 LDOS. BD71847 is reduced
version containing 6 bucks and 6 LDOs. Voltages for DVS
bucks (1-4 on BD71837, 1 and 2 on BD71847) can be adjusted
when regulators are enabled. For other bucks and LDOs we may
have over- or undershooting if voltage is adjusted when
regulator is enabled. Thus this is prevented by default.
BD718x7 has a quirk which may leave power output disabled
after reset if enable/disable state was controlled by SW.
Thus the SW control is only allowed for BD71837 bucks
3 and 4 by default. The impact of this limitation must be
evaluated board-by board and restrictions may need to be
modified. (Linux driver get's these limitations from DT and we
may want to implement same on u-Boot driver).
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add thermal dts node
Enable thermal in defconfig
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add i.MX8 thermal driver to support get temperature from SCU.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Add sc_misc_get_temp to support get temperature
Signed-off-by: Peng Fan <peng.fan@nxp.com>
|
|
Commit 32ce6179fb99 ("optee: Add lib entries for sharing OPTEE code across
ports") adds code into lib/optee but neglects to update MAINTAINERS to make
me buggable for questions and maintenance.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Jens Wiklander <jens.wiklander@linaro.org>
|
|
When booting in BL33 mode i.e. with u-boot loaded by OP-TEE we get the
following print-out.
Board: WARP7 in secure mode OPTEE DRAM 0xa0000000-0xa0000000
This is incorrect the right range is 0x9e000000-0xa0000000. This patch
fixes the defines on the warp7_bl33_defconfig file to tidy up the output.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
|
|
Commit c7b3a7ee5351 ("optee: adjust dependencies and default values for
dram") makes the TZDRAM defines for OPTEE show up for all configs as a
side-effect. While not harmful its not what we really want.
This patch makes the following defines contingent on CONFIG_OPTEE=y
CONFIG_OPTEE_TZDRAM_BASE
CONFIG_OPTEE_TZDRAM_SIZE
Rightly, if you don't have CONFIG_OPTEE=y you don't care about the above
two defines.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Acked-by: Rui Miguel Silva <rui.silva@linaro.org>
|
|
This patch converts mxs_spi driver to support DM/DTS.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
The code responsible for setting proper values in the MUX registers
(in the mxs_pinctrl_set_state()) has been ported from Linux kernel
- SHA1: 17bb763e7eaf tag v5.1.11 from linux-stable.
As the pinctrl node in the imx28.dtsi file has gpio pins nodes as subnodes,
it was necessary to use 'dm_scan_fdt_dev()' (as a .bind method) to also
make them 'visible' by the DM's "gpio_mxs" driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
This patch adds support for DM/DTS in the mxs_gpio.c driver.
Information regarding per gpio controller pin number is passed via DTS.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Those properties are U-Boot specific as the mxs gpio Linux driver (up to
version v5.1.11) is not supporting them.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The fec_mxc.c driver can be reused by i.MX28 when DM_ETH is enabled.
One only needs to add proper compatible and dependency on FEC_MXC in the
Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
This patch copies from the Linux kernel stable (tag v5.1.11)
SHA1: 17bb763e7eaf i.MX28 related device tree files.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Since the board uses SPL_OF_CONTROL now, we don't need to
explicitly initialize the MMC driver, but we still need to
pinmux the corresponding pins. This patch removes the
initialization code and leave just the muxing behind.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
With the spl code correctly returning either MMC1 or MMC2,
this board can not boot either from internal eMMC (MMC1) or
the uSD card on the baseboard (MMC2) using the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Currently, when the spl_boot_device checks the boot device, it
will only return MMC1 when it's either sd or eMMC regardless
of whether or not it's MMC1 or MMC2. This is a problem when
booting from MMC2 if MMC isn't being manually configured like in
the DM_SPL case with SPL_OF_CONTROL.
This patch will check the register and return either MMC1 or MMC2.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
|
|
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
|
|
The clock subsystem needs active maintenance as it steadily grows.
I do offer my help for this task.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Enable by default the Common Clock Framework [CCF] clock code for sandbox.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This patch provides code to implement the CCF clock tree in sandbox. It
uses all the introduced primitives; some generic ones are reused, some
sandbox specific were developed.
In that way (after introducing the real CCF tree in sandbox) the recently
added to clk-uclass.c: clk_get_by_id() and clk_get_parent_rate() are tested
in their natural work environment.
Usage (sandbox_defconfig and sandbox_flattree_defconfig):
./u-boot --fdt arch/sandbox/dts/test.dtb --command "ut dm clk_ccf"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The generic mux clock code for CCF requires reading the clock multiplexer
value from HW registers. As sandbox by design has readl() as no-op it was
necessary to provide this value in the other way.
The new field in the mux structure (accessible only when sandbox is run)
has been introduced for this purpose.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
The generic divider clock code for CCF requires reading the divider value
from HW registers. As sandbox by design has readl() as no-op it was
necessary to provide this value in the other way.
The new field in the divider structure (accessible only when sandbox is
run) has been introduced for this purpose.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This patch adds the 'osc' fixed clock to facilitate the CCF testing in
the sandbox U-Boot. It is a starting point for building CCF hierarchy of
clocks.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
If the CLK_GET_RATE_NOCACHE flag is set - the clk_get_parent_rate()
provides recalculated clock value without considering the cache setting.
This may be necessary for some clocks tightly coupled with power domains
(i.e. imx8), and prevents from reading invalid cached values.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This patch brings the files from Linux kernel (linux-stable/linux-5.1.y
SHA1: 5752b50477da)to provide clocks support as it is used on the Linux
kernel with Common Clock Framework [CCF] setup.
The directory structure has been preserved. The ported code only supports
reading information from PLL, MUX, Divider, etc and enabling/disabling
the clocks USDHCx/ECSPIx depending on used bus. Moreover, it is agnostic
to the alias numbering as the information about the clock is read from the
device tree.
One needs to pay attention to the comments indicating necessary for U-Boot's
driver model changes.
If needed, the code can be extended to support the "set" part of the clock
management.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This commit adds the clk_get_by_id() function, which is responsible
for getting the udevice with matching clk->id. Such approach allows
re-usage of inherit DM list relationship for the same class (UCLASS_CLK).
As a result - we don't need any other external list - it is just enough
to look for UCLASS_CLK related udevices.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This commit adds the clk_get_parent_rate() function, which is responsible
for getting the rate of parent clock.
Unfortunately, u-boot's DM support for getting parent is different
(the parent relationship is in udevice) than the one in Common Clock
Framework [CCF] in Linux.
To alleviate this problem - the clk_get_parent_rate() function has been
introduced to clk-uclass.c.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This commit adds the clk_get_parent() function, which is responsible
for getting the parent's struct clock pointer.
U-Boot's DM support for getting parent is different (the parent
relationship is in udevice) than the one in Common Clock Framework [CCF]
in Linux. To obtain the pointer to struct clk of parent the
pdev->uclass_priv field is read via dev_get_clk_ptr() wrapper.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This file now stores the dev_get_clk_ptr() wrapper on the dev_get_uclass_priv()
function.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Up till now the fixed rate clock ('osc') has been added to UCLASS_CLK
without declaring struct clk. As a result it was only accessible by
iterating the udevice's uclass list.
This is a problem for clock code, which operates on pointers to struct
clk (like clk_get_rate()), not udevices.
After this change struct clk is accessible from udevice and udevice from
struct clk.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This commit extends the struct clk to provide information regarding the
flags related to this devices.
Those flags are clk device agnostic and indicate generic features
(like e.g. CLK_GET_RATE_NOCACHE - the need to always recalculate the rate).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This commit extends the struct clk to provide information regarding the
clock rate.
As a result the clock tree traversal is performed at most once, and further
reads are using the cached value.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
This check requires the struct clk passed to .get_rate() to be always
cleared out as any clock with valid ID causes -EINVAL return value.
The return code of fixed clocks shall always be returned.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
There is no UCLASS_CLOCK uclass defined. Instead we do use the UCLASS_CLK.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
|
|
This patch describes the design decisions considerations and taken approach
for porting in a separate documentation entry.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
|
|
We now have a proper fix for this test, stop disabling it in CI.
This reverts commit ae8d23a668755d804748a1cf848426b28338b3d5.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
barno was mistakely readed from the target structure,
resulting in undefined behavious depending on the previous memory
content. fix that.
Fixes: bb413337826e ("pci_ep: add pci endpoint sandbox driver")
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
[trini: Drop unused bar_idx]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Removed one of the defconfig(obsoleted) file
and unused CONFIG_MMC_SPI definition to avoid confusion
about if this board using non-DM stuff or not.
uCP1020 is completely DM free board, tested and runs well.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Some storage devices have multiple hw partitions and both address from
zero, for example eMMC.
However currently block cache invalidation only applies to block
write/erase.
This can cause a problem that data of current hw partition is cached
before switching to another hw partition. And the following read
operation of the latter hw partition will get wrong data when reading
from the addresses that have been cached previously.
To solve this problem, invalidate block cache after a successful
select_hwpart operation.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch removes tick-timer as all mt7629 boards should use arch timer.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
This patch changes mt7629_rfb to use ARM's generic arch timer instead of
MediaTek's soc timer.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
The timer0 node has its two clocks written in reversed order. The timer0
is used as the tick timer which causes a problem that the time a delay
function used is 4 times longer.
This patch reverses these two clocks to solve this issue.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
We don't need a full checkout of Chrome OS to build U-Boot with
Chromium OS verified boot. Update the instructions accordingly and fix a
typo which joins the output directory and defconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This patch sets CNTVOFF of ARM CP15 timer to zero to make sure the virtual
counter is fully usable for linux kernel.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
|
|
%s/ot/to/
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
